1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Copyright (C) 2010 Google, Inc. 4 * Copyright (C) 2013 NVIDIA Corporation 5 * 6 * Author: 7 * Erik Gilling <konkers@google.com> 8 * Benoit Goby <benoit@android.com> 9 * Venu Byravarasu <vbyravarasu@nvidia.com> 10 */ 11 12 #include <linux/delay.h> 13 #include <linux/err.h> 14 #include <linux/export.h> 15 #include <linux/gpio/consumer.h> 16 #include <linux/iopoll.h> 17 #include <linux/module.h> 18 #include <linux/of.h> 19 #include <linux/of_platform.h> 20 #include <linux/platform_device.h> 21 #include <linux/resource.h> 22 #include <linux/slab.h> 23 #include <linux/spinlock.h> 24 25 #include <linux/regulator/consumer.h> 26 27 #include <linux/usb/ehci_def.h> 28 #include <linux/usb/of.h> 29 #include <linux/usb/tegra_usb_phy.h> 30 #include <linux/usb/ulpi.h> 31 32 #define ULPI_VIEWPORT 0x170 33 34 /* PORTSC PTS/PHCD bits, Tegra20 only */ 35 #define TEGRA_USB_PORTSC1 0x184 36 #define TEGRA_USB_PORTSC1_PTS(x) (((x) & 0x3) << 30) 37 #define TEGRA_USB_PORTSC1_PHCD BIT(23) 38 39 /* HOSTPC1 PTS/PHCD bits, Tegra30 and above */ 40 #define TEGRA_USB_HOSTPC1_DEVLC 0x1b4 41 #define TEGRA_USB_HOSTPC1_DEVLC_PTS(x) (((x) & 0x7) << 29) 42 #define TEGRA_USB_HOSTPC1_DEVLC_PHCD BIT(22) 43 44 /* Bits of PORTSC1, which will get cleared by writing 1 into them */ 45 #define TEGRA_PORTSC1_RWC_BITS (PORT_CSC | PORT_PEC | PORT_OCC) 46 47 #define USB_SUSP_CTRL 0x400 48 #define USB_WAKE_ON_RESUME_EN BIT(2) 49 #define USB_WAKE_ON_CNNT_EN_DEV BIT(3) 50 #define USB_WAKE_ON_DISCON_EN_DEV BIT(4) 51 #define USB_SUSP_CLR BIT(5) 52 #define USB_PHY_CLK_VALID BIT(7) 53 #define UTMIP_RESET BIT(11) 54 #define UHSIC_RESET BIT(11) 55 #define UTMIP_PHY_ENABLE BIT(12) 56 #define ULPI_PHY_ENABLE BIT(13) 57 #define USB_SUSP_SET BIT(14) 58 #define USB_WAKEUP_DEBOUNCE_COUNT(x) (((x) & 0x7) << 16) 59 60 #define USB_PHY_VBUS_SENSORS 0x404 61 #define B_SESS_VLD_WAKEUP_EN BIT(14) 62 #define A_SESS_VLD_WAKEUP_EN BIT(22) 63 #define A_VBUS_VLD_WAKEUP_EN BIT(30) 64 65 #define USB_PHY_VBUS_WAKEUP_ID 0x408 66 #define ID_INT_EN BIT(0) 67 #define ID_CHG_DET BIT(1) 68 #define VBUS_WAKEUP_INT_EN BIT(8) 69 #define VBUS_WAKEUP_CHG_DET BIT(9) 70 #define VBUS_WAKEUP_STS BIT(10) 71 #define VBUS_WAKEUP_WAKEUP_EN BIT(30) 72 73 #define USB1_LEGACY_CTRL 0x410 74 #define USB1_NO_LEGACY_MODE BIT(0) 75 #define USB1_VBUS_SENSE_CTL_MASK (3 << 1) 76 #define USB1_VBUS_SENSE_CTL_VBUS_WAKEUP (0 << 1) 77 #define USB1_VBUS_SENSE_CTL_AB_SESS_VLD_OR_VBUS_WAKEUP \ 78 (1 << 1) 79 #define USB1_VBUS_SENSE_CTL_AB_SESS_VLD (2 << 1) 80 #define USB1_VBUS_SENSE_CTL_A_SESS_VLD (3 << 1) 81 82 #define ULPI_TIMING_CTRL_0 0x424 83 #define ULPI_OUTPUT_PINMUX_BYP BIT(10) 84 #define ULPI_CLKOUT_PINMUX_BYP BIT(11) 85 86 #define ULPI_TIMING_CTRL_1 0x428 87 #define ULPI_DATA_TRIMMER_LOAD BIT(0) 88 #define ULPI_DATA_TRIMMER_SEL(x) (((x) & 0x7) << 1) 89 #define ULPI_STPDIRNXT_TRIMMER_LOAD BIT(16) 90 #define ULPI_STPDIRNXT_TRIMMER_SEL(x) (((x) & 0x7) << 17) 91 #define ULPI_DIR_TRIMMER_LOAD BIT(24) 92 #define ULPI_DIR_TRIMMER_SEL(x) (((x) & 0x7) << 25) 93 94 #define UTMIP_PLL_CFG1 0x804 95 #define UTMIP_XTAL_FREQ_COUNT(x) (((x) & 0xfff) << 0) 96 #define UTMIP_PLLU_ENABLE_DLY_COUNT(x) (((x) & 0x1f) << 27) 97 98 #define UTMIP_XCVR_CFG0 0x808 99 #define UTMIP_XCVR_SETUP(x) (((x) & 0xf) << 0) 100 #define UTMIP_XCVR_SETUP_MSB(x) ((((x) & 0x70) >> 4) << 22) 101 #define UTMIP_XCVR_LSRSLEW(x) (((x) & 0x3) << 8) 102 #define UTMIP_XCVR_LSFSLEW(x) (((x) & 0x3) << 10) 103 #define UTMIP_FORCE_PD_POWERDOWN BIT(14) 104 #define UTMIP_FORCE_PD2_POWERDOWN BIT(16) 105 #define UTMIP_FORCE_PDZI_POWERDOWN BIT(18) 106 #define UTMIP_XCVR_LSBIAS_SEL BIT(21) 107 #define UTMIP_XCVR_HSSLEW(x) (((x) & 0x3) << 4) 108 #define UTMIP_XCVR_HSSLEW_MSB(x) ((((x) & 0x1fc) >> 2) << 25) 109 110 #define UTMIP_BIAS_CFG0 0x80c 111 #define UTMIP_OTGPD BIT(11) 112 #define UTMIP_BIASPD BIT(10) 113 #define UTMIP_HSSQUELCH_LEVEL(x) (((x) & 0x3) << 0) 114 #define UTMIP_HSDISCON_LEVEL(x) (((x) & 0x3) << 2) 115 #define UTMIP_HSDISCON_LEVEL_MSB(x) ((((x) & 0x4) >> 2) << 24) 116 117 #define UTMIP_HSRX_CFG0 0x810 118 #define UTMIP_ELASTIC_LIMIT(x) (((x) & 0x1f) << 10) 119 #define UTMIP_IDLE_WAIT(x) (((x) & 0x1f) << 15) 120 121 #define UTMIP_HSRX_CFG1 0x814 122 #define UTMIP_HS_SYNC_START_DLY(x) (((x) & 0x1f) << 1) 123 124 #define UTMIP_TX_CFG0 0x820 125 #define UTMIP_FS_PREABMLE_J BIT(19) 126 #define UTMIP_HS_DISCON_DISABLE BIT(8) 127 128 #define UTMIP_MISC_CFG0 0x824 129 #define UTMIP_DPDM_OBSERVE BIT(26) 130 #define UTMIP_DPDM_OBSERVE_SEL(x) (((x) & 0xf) << 27) 131 #define UTMIP_DPDM_OBSERVE_SEL_FS_J UTMIP_DPDM_OBSERVE_SEL(0xf) 132 #define UTMIP_DPDM_OBSERVE_SEL_FS_K UTMIP_DPDM_OBSERVE_SEL(0xe) 133 #define UTMIP_DPDM_OBSERVE_SEL_FS_SE1 UTMIP_DPDM_OBSERVE_SEL(0xd) 134 #define UTMIP_DPDM_OBSERVE_SEL_FS_SE0 UTMIP_DPDM_OBSERVE_SEL(0xc) 135 #define UTMIP_SUSPEND_EXIT_ON_EDGE BIT(22) 136 137 #define UTMIP_MISC_CFG1 0x828 138 #define UTMIP_PLL_ACTIVE_DLY_COUNT(x) (((x) & 0x1f) << 18) 139 #define UTMIP_PLLU_STABLE_COUNT(x) (((x) & 0xfff) << 6) 140 141 #define UTMIP_DEBOUNCE_CFG0 0x82c 142 #define UTMIP_BIAS_DEBOUNCE_A(x) (((x) & 0xffff) << 0) 143 144 #define UTMIP_BAT_CHRG_CFG0 0x830 145 #define UTMIP_PD_CHRG BIT(0) 146 147 #define UTMIP_SPARE_CFG0 0x834 148 #define FUSE_SETUP_SEL BIT(3) 149 150 #define UTMIP_XCVR_CFG1 0x838 151 #define UTMIP_FORCE_PDDISC_POWERDOWN BIT(0) 152 #define UTMIP_FORCE_PDCHRP_POWERDOWN BIT(2) 153 #define UTMIP_FORCE_PDDR_POWERDOWN BIT(4) 154 #define UTMIP_XCVR_TERM_RANGE_ADJ(x) (((x) & 0xf) << 18) 155 156 #define UTMIP_BIAS_CFG1 0x83c 157 #define UTMIP_BIAS_PDTRK_COUNT(x) (((x) & 0x1f) << 3) 158 159 /* For Tegra30 and above only, the address is different in Tegra20 */ 160 #define USB_USBMODE 0x1f8 161 #define USB_USBMODE_MASK (3 << 0) 162 #define USB_USBMODE_HOST (3 << 0) 163 #define USB_USBMODE_DEVICE (2 << 0) 164 165 #define PMC_USB_AO 0xf0 166 #define VBUS_WAKEUP_PD_P0 BIT(2) 167 #define ID_PD_P0 BIT(3) 168 169 static DEFINE_SPINLOCK(utmip_pad_lock); 170 static unsigned int utmip_pad_count; 171 172 struct tegra_xtal_freq { 173 unsigned int freq; 174 u8 enable_delay; 175 u8 stable_count; 176 u8 active_delay; 177 u8 xtal_freq_count; 178 u16 debounce; 179 }; 180 181 static const struct tegra_xtal_freq tegra_freq_table[] = { 182 { 183 .freq = 12000000, 184 .enable_delay = 0x02, 185 .stable_count = 0x2F, 186 .active_delay = 0x04, 187 .xtal_freq_count = 0x76, 188 .debounce = 0x7530, 189 }, 190 { 191 .freq = 13000000, 192 .enable_delay = 0x02, 193 .stable_count = 0x33, 194 .active_delay = 0x05, 195 .xtal_freq_count = 0x7F, 196 .debounce = 0x7EF4, 197 }, 198 { 199 .freq = 19200000, 200 .enable_delay = 0x03, 201 .stable_count = 0x4B, 202 .active_delay = 0x06, 203 .xtal_freq_count = 0xBB, 204 .debounce = 0xBB80, 205 }, 206 { 207 .freq = 26000000, 208 .enable_delay = 0x04, 209 .stable_count = 0x66, 210 .active_delay = 0x09, 211 .xtal_freq_count = 0xFE, 212 .debounce = 0xFDE8, 213 }, 214 }; 215 216 static inline struct tegra_usb_phy *to_tegra_usb_phy(struct usb_phy *u_phy) 217 { 218 return container_of(u_phy, struct tegra_usb_phy, u_phy); 219 } 220 221 static void set_pts(struct tegra_usb_phy *phy, u8 pts_val) 222 { 223 void __iomem *base = phy->regs; 224 u32 val; 225 226 if (phy->soc_config->has_hostpc) { 227 val = readl_relaxed(base + TEGRA_USB_HOSTPC1_DEVLC); 228 val &= ~TEGRA_USB_HOSTPC1_DEVLC_PTS(~0); 229 val |= TEGRA_USB_HOSTPC1_DEVLC_PTS(pts_val); 230 writel_relaxed(val, base + TEGRA_USB_HOSTPC1_DEVLC); 231 } else { 232 val = readl_relaxed(base + TEGRA_USB_PORTSC1); 233 val &= ~TEGRA_PORTSC1_RWC_BITS; 234 val &= ~TEGRA_USB_PORTSC1_PTS(~0); 235 val |= TEGRA_USB_PORTSC1_PTS(pts_val); 236 writel_relaxed(val, base + TEGRA_USB_PORTSC1); 237 } 238 } 239 240 static void set_phcd(struct tegra_usb_phy *phy, bool enable) 241 { 242 void __iomem *base = phy->regs; 243 u32 val; 244 245 if (phy->soc_config->has_hostpc) { 246 val = readl_relaxed(base + TEGRA_USB_HOSTPC1_DEVLC); 247 if (enable) 248 val |= TEGRA_USB_HOSTPC1_DEVLC_PHCD; 249 else 250 val &= ~TEGRA_USB_HOSTPC1_DEVLC_PHCD; 251 writel_relaxed(val, base + TEGRA_USB_HOSTPC1_DEVLC); 252 } else { 253 val = readl_relaxed(base + TEGRA_USB_PORTSC1) & ~PORT_RWC_BITS; 254 if (enable) 255 val |= TEGRA_USB_PORTSC1_PHCD; 256 else 257 val &= ~TEGRA_USB_PORTSC1_PHCD; 258 writel_relaxed(val, base + TEGRA_USB_PORTSC1); 259 } 260 } 261 262 static int utmip_pad_open(struct tegra_usb_phy *phy) 263 { 264 int ret; 265 266 ret = clk_prepare_enable(phy->pad_clk); 267 if (ret) { 268 dev_err(phy->u_phy.dev, 269 "Failed to enable UTMI-pads clock: %d\n", ret); 270 return ret; 271 } 272 273 spin_lock(&utmip_pad_lock); 274 275 ret = reset_control_deassert(phy->pad_rst); 276 if (ret) { 277 dev_err(phy->u_phy.dev, 278 "Failed to initialize UTMI-pads reset: %d\n", ret); 279 goto unlock; 280 } 281 282 ret = reset_control_assert(phy->pad_rst); 283 if (ret) { 284 dev_err(phy->u_phy.dev, 285 "Failed to assert UTMI-pads reset: %d\n", ret); 286 goto unlock; 287 } 288 289 udelay(1); 290 291 ret = reset_control_deassert(phy->pad_rst); 292 if (ret) 293 dev_err(phy->u_phy.dev, 294 "Failed to deassert UTMI-pads reset: %d\n", ret); 295 unlock: 296 spin_unlock(&utmip_pad_lock); 297 298 clk_disable_unprepare(phy->pad_clk); 299 300 return ret; 301 } 302 303 static int utmip_pad_close(struct tegra_usb_phy *phy) 304 { 305 int ret; 306 307 ret = clk_prepare_enable(phy->pad_clk); 308 if (ret) { 309 dev_err(phy->u_phy.dev, 310 "Failed to enable UTMI-pads clock: %d\n", ret); 311 return ret; 312 } 313 314 ret = reset_control_assert(phy->pad_rst); 315 if (ret) 316 dev_err(phy->u_phy.dev, 317 "Failed to assert UTMI-pads reset: %d\n", ret); 318 319 udelay(1); 320 321 clk_disable_unprepare(phy->pad_clk); 322 323 return ret; 324 } 325 326 static int utmip_pad_power_on(struct tegra_usb_phy *phy) 327 { 328 struct tegra_utmip_config *config = phy->config; 329 void __iomem *base = phy->pad_regs; 330 u32 val; 331 int err; 332 333 err = clk_prepare_enable(phy->pad_clk); 334 if (err) 335 return err; 336 337 spin_lock(&utmip_pad_lock); 338 339 if (utmip_pad_count++ == 0) { 340 val = readl_relaxed(base + UTMIP_BIAS_CFG0); 341 val &= ~(UTMIP_OTGPD | UTMIP_BIASPD); 342 343 if (phy->soc_config->requires_extra_tuning_parameters) { 344 val &= ~(UTMIP_HSSQUELCH_LEVEL(~0) | 345 UTMIP_HSDISCON_LEVEL(~0) | 346 UTMIP_HSDISCON_LEVEL_MSB(~0)); 347 348 val |= UTMIP_HSSQUELCH_LEVEL(config->hssquelch_level); 349 val |= UTMIP_HSDISCON_LEVEL(config->hsdiscon_level); 350 val |= UTMIP_HSDISCON_LEVEL_MSB(config->hsdiscon_level); 351 } 352 writel_relaxed(val, base + UTMIP_BIAS_CFG0); 353 } 354 355 if (phy->pad_wakeup) { 356 phy->pad_wakeup = false; 357 utmip_pad_count--; 358 } 359 360 spin_unlock(&utmip_pad_lock); 361 362 clk_disable_unprepare(phy->pad_clk); 363 364 return 0; 365 } 366 367 static int utmip_pad_power_off(struct tegra_usb_phy *phy) 368 { 369 void __iomem *base = phy->pad_regs; 370 u32 val; 371 int ret; 372 373 ret = clk_prepare_enable(phy->pad_clk); 374 if (ret) 375 return ret; 376 377 spin_lock(&utmip_pad_lock); 378 379 if (!utmip_pad_count) { 380 dev_err(phy->u_phy.dev, "UTMIP pad already powered off\n"); 381 ret = -EINVAL; 382 goto ulock; 383 } 384 385 /* 386 * In accordance to TRM, OTG and Bias pad circuits could be turned off 387 * to save power if wake is enabled, but the VBUS-change detection 388 * method is board-specific and these circuits may need to be enabled 389 * to generate wakeup event, hence we will just keep them both enabled. 390 */ 391 if (phy->wakeup_enabled) { 392 phy->pad_wakeup = true; 393 utmip_pad_count++; 394 } 395 396 if (--utmip_pad_count == 0) { 397 val = readl_relaxed(base + UTMIP_BIAS_CFG0); 398 val |= UTMIP_OTGPD | UTMIP_BIASPD; 399 writel_relaxed(val, base + UTMIP_BIAS_CFG0); 400 } 401 ulock: 402 spin_unlock(&utmip_pad_lock); 403 404 clk_disable_unprepare(phy->pad_clk); 405 406 return ret; 407 } 408 409 static int utmi_wait_register(void __iomem *reg, u32 mask, u32 result) 410 { 411 u32 tmp; 412 413 return readl_relaxed_poll_timeout(reg, tmp, (tmp & mask) == result, 414 2000, 6000); 415 } 416 417 static void utmi_phy_clk_disable(struct tegra_usb_phy *phy) 418 { 419 void __iomem *base = phy->regs; 420 u32 val; 421 422 /* 423 * The USB driver may have already initiated the phy clock 424 * disable so wait to see if the clock turns off and if not 425 * then proceed with gating the clock. 426 */ 427 if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, 0) == 0) 428 return; 429 430 if (phy->is_legacy_phy) { 431 val = readl_relaxed(base + USB_SUSP_CTRL); 432 val |= USB_SUSP_SET; 433 writel_relaxed(val, base + USB_SUSP_CTRL); 434 435 usleep_range(10, 100); 436 437 val = readl_relaxed(base + USB_SUSP_CTRL); 438 val &= ~USB_SUSP_SET; 439 writel_relaxed(val, base + USB_SUSP_CTRL); 440 } else { 441 set_phcd(phy, true); 442 } 443 444 if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, 0)) 445 dev_err(phy->u_phy.dev, 446 "Timeout waiting for PHY to stabilize on disable\n"); 447 } 448 449 static void utmi_phy_clk_enable(struct tegra_usb_phy *phy) 450 { 451 void __iomem *base = phy->regs; 452 u32 val; 453 454 /* 455 * The USB driver may have already initiated the phy clock 456 * enable so wait to see if the clock turns on and if not 457 * then proceed with ungating the clock. 458 */ 459 if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, 460 USB_PHY_CLK_VALID) == 0) 461 return; 462 463 if (phy->is_legacy_phy) { 464 val = readl_relaxed(base + USB_SUSP_CTRL); 465 val |= USB_SUSP_CLR; 466 writel_relaxed(val, base + USB_SUSP_CTRL); 467 468 usleep_range(10, 100); 469 470 val = readl_relaxed(base + USB_SUSP_CTRL); 471 val &= ~USB_SUSP_CLR; 472 writel_relaxed(val, base + USB_SUSP_CTRL); 473 } else { 474 set_phcd(phy, false); 475 } 476 477 if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, 478 USB_PHY_CLK_VALID)) 479 dev_err(phy->u_phy.dev, 480 "Timeout waiting for PHY to stabilize on enable\n"); 481 } 482 483 static int utmi_phy_power_on(struct tegra_usb_phy *phy) 484 { 485 struct tegra_utmip_config *config = phy->config; 486 void __iomem *base = phy->regs; 487 u32 val; 488 int err; 489 490 val = readl_relaxed(base + USB_SUSP_CTRL); 491 val |= UTMIP_RESET; 492 writel_relaxed(val, base + USB_SUSP_CTRL); 493 494 if (phy->is_legacy_phy) { 495 val = readl_relaxed(base + USB1_LEGACY_CTRL); 496 val |= USB1_NO_LEGACY_MODE; 497 writel_relaxed(val, base + USB1_LEGACY_CTRL); 498 } 499 500 val = readl_relaxed(base + UTMIP_TX_CFG0); 501 val |= UTMIP_FS_PREABMLE_J; 502 writel_relaxed(val, base + UTMIP_TX_CFG0); 503 504 val = readl_relaxed(base + UTMIP_HSRX_CFG0); 505 val &= ~(UTMIP_IDLE_WAIT(~0) | UTMIP_ELASTIC_LIMIT(~0)); 506 val |= UTMIP_IDLE_WAIT(config->idle_wait_delay); 507 val |= UTMIP_ELASTIC_LIMIT(config->elastic_limit); 508 writel_relaxed(val, base + UTMIP_HSRX_CFG0); 509 510 val = readl_relaxed(base + UTMIP_HSRX_CFG1); 511 val &= ~UTMIP_HS_SYNC_START_DLY(~0); 512 val |= UTMIP_HS_SYNC_START_DLY(config->hssync_start_delay); 513 writel_relaxed(val, base + UTMIP_HSRX_CFG1); 514 515 val = readl_relaxed(base + UTMIP_DEBOUNCE_CFG0); 516 val &= ~UTMIP_BIAS_DEBOUNCE_A(~0); 517 val |= UTMIP_BIAS_DEBOUNCE_A(phy->freq->debounce); 518 writel_relaxed(val, base + UTMIP_DEBOUNCE_CFG0); 519 520 val = readl_relaxed(base + UTMIP_MISC_CFG0); 521 val &= ~UTMIP_SUSPEND_EXIT_ON_EDGE; 522 writel_relaxed(val, base + UTMIP_MISC_CFG0); 523 524 if (!phy->soc_config->utmi_pll_config_in_car_module) { 525 val = readl_relaxed(base + UTMIP_MISC_CFG1); 526 val &= ~(UTMIP_PLL_ACTIVE_DLY_COUNT(~0) | 527 UTMIP_PLLU_STABLE_COUNT(~0)); 528 val |= UTMIP_PLL_ACTIVE_DLY_COUNT(phy->freq->active_delay) | 529 UTMIP_PLLU_STABLE_COUNT(phy->freq->stable_count); 530 writel_relaxed(val, base + UTMIP_MISC_CFG1); 531 532 val = readl_relaxed(base + UTMIP_PLL_CFG1); 533 val &= ~(UTMIP_XTAL_FREQ_COUNT(~0) | 534 UTMIP_PLLU_ENABLE_DLY_COUNT(~0)); 535 val |= UTMIP_XTAL_FREQ_COUNT(phy->freq->xtal_freq_count) | 536 UTMIP_PLLU_ENABLE_DLY_COUNT(phy->freq->enable_delay); 537 writel_relaxed(val, base + UTMIP_PLL_CFG1); 538 } 539 540 val = readl_relaxed(base + USB_SUSP_CTRL); 541 val &= ~USB_WAKE_ON_RESUME_EN; 542 writel_relaxed(val, base + USB_SUSP_CTRL); 543 544 if (phy->mode != USB_DR_MODE_HOST) { 545 val = readl_relaxed(base + USB_SUSP_CTRL); 546 val &= ~(USB_WAKE_ON_CNNT_EN_DEV | USB_WAKE_ON_DISCON_EN_DEV); 547 writel_relaxed(val, base + USB_SUSP_CTRL); 548 549 val = readl_relaxed(base + USB_PHY_VBUS_WAKEUP_ID); 550 val &= ~VBUS_WAKEUP_WAKEUP_EN; 551 val &= ~(ID_CHG_DET | VBUS_WAKEUP_CHG_DET); 552 writel_relaxed(val, base + USB_PHY_VBUS_WAKEUP_ID); 553 554 val = readl_relaxed(base + USB_PHY_VBUS_SENSORS); 555 val &= ~(A_VBUS_VLD_WAKEUP_EN | A_SESS_VLD_WAKEUP_EN); 556 val &= ~(B_SESS_VLD_WAKEUP_EN); 557 writel_relaxed(val, base + USB_PHY_VBUS_SENSORS); 558 559 val = readl_relaxed(base + UTMIP_BAT_CHRG_CFG0); 560 val &= ~UTMIP_PD_CHRG; 561 writel_relaxed(val, base + UTMIP_BAT_CHRG_CFG0); 562 } else { 563 val = readl_relaxed(base + UTMIP_BAT_CHRG_CFG0); 564 val |= UTMIP_PD_CHRG; 565 writel_relaxed(val, base + UTMIP_BAT_CHRG_CFG0); 566 } 567 568 err = utmip_pad_power_on(phy); 569 if (err) 570 return err; 571 572 val = readl_relaxed(base + UTMIP_XCVR_CFG0); 573 val &= ~(UTMIP_FORCE_PD_POWERDOWN | UTMIP_FORCE_PD2_POWERDOWN | 574 UTMIP_FORCE_PDZI_POWERDOWN | UTMIP_XCVR_LSBIAS_SEL | 575 UTMIP_XCVR_SETUP(~0) | UTMIP_XCVR_SETUP_MSB(~0) | 576 UTMIP_XCVR_LSFSLEW(~0) | UTMIP_XCVR_LSRSLEW(~0)); 577 578 if (!config->xcvr_setup_use_fuses) { 579 val |= UTMIP_XCVR_SETUP(config->xcvr_setup); 580 val |= UTMIP_XCVR_SETUP_MSB(config->xcvr_setup); 581 } 582 val |= UTMIP_XCVR_LSFSLEW(config->xcvr_lsfslew); 583 val |= UTMIP_XCVR_LSRSLEW(config->xcvr_lsrslew); 584 585 if (phy->soc_config->requires_extra_tuning_parameters) { 586 val &= ~(UTMIP_XCVR_HSSLEW(~0) | UTMIP_XCVR_HSSLEW_MSB(~0)); 587 val |= UTMIP_XCVR_HSSLEW(config->xcvr_hsslew); 588 val |= UTMIP_XCVR_HSSLEW_MSB(config->xcvr_hsslew); 589 } 590 writel_relaxed(val, base + UTMIP_XCVR_CFG0); 591 592 val = readl_relaxed(base + UTMIP_XCVR_CFG1); 593 val &= ~(UTMIP_FORCE_PDDISC_POWERDOWN | UTMIP_FORCE_PDCHRP_POWERDOWN | 594 UTMIP_FORCE_PDDR_POWERDOWN | UTMIP_XCVR_TERM_RANGE_ADJ(~0)); 595 val |= UTMIP_XCVR_TERM_RANGE_ADJ(config->term_range_adj); 596 writel_relaxed(val, base + UTMIP_XCVR_CFG1); 597 598 val = readl_relaxed(base + UTMIP_BIAS_CFG1); 599 val &= ~UTMIP_BIAS_PDTRK_COUNT(~0); 600 val |= UTMIP_BIAS_PDTRK_COUNT(0x5); 601 writel_relaxed(val, base + UTMIP_BIAS_CFG1); 602 603 val = readl_relaxed(base + UTMIP_SPARE_CFG0); 604 if (config->xcvr_setup_use_fuses) 605 val |= FUSE_SETUP_SEL; 606 else 607 val &= ~FUSE_SETUP_SEL; 608 writel_relaxed(val, base + UTMIP_SPARE_CFG0); 609 610 if (!phy->is_legacy_phy) { 611 val = readl_relaxed(base + USB_SUSP_CTRL); 612 val |= UTMIP_PHY_ENABLE; 613 writel_relaxed(val, base + USB_SUSP_CTRL); 614 } 615 616 val = readl_relaxed(base + USB_SUSP_CTRL); 617 val &= ~UTMIP_RESET; 618 writel_relaxed(val, base + USB_SUSP_CTRL); 619 620 if (phy->is_legacy_phy) { 621 val = readl_relaxed(base + USB1_LEGACY_CTRL); 622 val &= ~USB1_VBUS_SENSE_CTL_MASK; 623 val |= USB1_VBUS_SENSE_CTL_A_SESS_VLD; 624 writel_relaxed(val, base + USB1_LEGACY_CTRL); 625 626 val = readl_relaxed(base + USB_SUSP_CTRL); 627 val &= ~USB_SUSP_SET; 628 writel_relaxed(val, base + USB_SUSP_CTRL); 629 } 630 631 utmi_phy_clk_enable(phy); 632 633 if (phy->soc_config->requires_usbmode_setup) { 634 val = readl_relaxed(base + USB_USBMODE); 635 val &= ~USB_USBMODE_MASK; 636 if (phy->mode == USB_DR_MODE_HOST) 637 val |= USB_USBMODE_HOST; 638 else 639 val |= USB_USBMODE_DEVICE; 640 writel_relaxed(val, base + USB_USBMODE); 641 } 642 643 if (!phy->is_legacy_phy) 644 set_pts(phy, 0); 645 646 return 0; 647 } 648 649 static int utmi_phy_power_off(struct tegra_usb_phy *phy) 650 { 651 void __iomem *base = phy->regs; 652 u32 val; 653 654 /* 655 * Give hardware time to settle down after VBUS disconnection, 656 * otherwise PHY will immediately wake up from suspend. 657 */ 658 if (phy->wakeup_enabled && phy->mode != USB_DR_MODE_HOST) 659 readl_relaxed_poll_timeout(base + USB_PHY_VBUS_WAKEUP_ID, 660 val, !(val & VBUS_WAKEUP_STS), 661 5000, 100000); 662 663 utmi_phy_clk_disable(phy); 664 665 /* PHY won't resume if reset is asserted */ 666 if (!phy->wakeup_enabled) { 667 val = readl_relaxed(base + USB_SUSP_CTRL); 668 val |= UTMIP_RESET; 669 writel_relaxed(val, base + USB_SUSP_CTRL); 670 } 671 672 val = readl_relaxed(base + UTMIP_BAT_CHRG_CFG0); 673 val |= UTMIP_PD_CHRG; 674 writel_relaxed(val, base + UTMIP_BAT_CHRG_CFG0); 675 676 if (!phy->wakeup_enabled) { 677 val = readl_relaxed(base + UTMIP_XCVR_CFG0); 678 val |= UTMIP_FORCE_PD_POWERDOWN | UTMIP_FORCE_PD2_POWERDOWN | 679 UTMIP_FORCE_PDZI_POWERDOWN; 680 writel_relaxed(val, base + UTMIP_XCVR_CFG0); 681 } 682 683 val = readl_relaxed(base + UTMIP_XCVR_CFG1); 684 val |= UTMIP_FORCE_PDDISC_POWERDOWN | UTMIP_FORCE_PDCHRP_POWERDOWN | 685 UTMIP_FORCE_PDDR_POWERDOWN; 686 writel_relaxed(val, base + UTMIP_XCVR_CFG1); 687 688 if (phy->wakeup_enabled) { 689 val = readl_relaxed(base + USB_SUSP_CTRL); 690 val &= ~USB_WAKEUP_DEBOUNCE_COUNT(~0); 691 val |= USB_WAKEUP_DEBOUNCE_COUNT(5); 692 val |= USB_WAKE_ON_RESUME_EN; 693 writel_relaxed(val, base + USB_SUSP_CTRL); 694 695 /* 696 * Ask VBUS sensor to generate wake event once cable is 697 * connected. 698 */ 699 if (phy->mode != USB_DR_MODE_HOST) { 700 val = readl_relaxed(base + USB_PHY_VBUS_WAKEUP_ID); 701 val |= VBUS_WAKEUP_WAKEUP_EN; 702 val &= ~(ID_CHG_DET | VBUS_WAKEUP_CHG_DET); 703 writel_relaxed(val, base + USB_PHY_VBUS_WAKEUP_ID); 704 705 val = readl_relaxed(base + USB_PHY_VBUS_SENSORS); 706 val |= A_VBUS_VLD_WAKEUP_EN; 707 writel_relaxed(val, base + USB_PHY_VBUS_SENSORS); 708 } 709 } 710 711 return utmip_pad_power_off(phy); 712 } 713 714 static void utmi_phy_preresume(struct tegra_usb_phy *phy) 715 { 716 void __iomem *base = phy->regs; 717 u32 val; 718 719 val = readl_relaxed(base + UTMIP_TX_CFG0); 720 val |= UTMIP_HS_DISCON_DISABLE; 721 writel_relaxed(val, base + UTMIP_TX_CFG0); 722 } 723 724 static void utmi_phy_postresume(struct tegra_usb_phy *phy) 725 { 726 void __iomem *base = phy->regs; 727 u32 val; 728 729 val = readl_relaxed(base + UTMIP_TX_CFG0); 730 val &= ~UTMIP_HS_DISCON_DISABLE; 731 writel_relaxed(val, base + UTMIP_TX_CFG0); 732 } 733 734 static void utmi_phy_restore_start(struct tegra_usb_phy *phy, 735 enum tegra_usb_phy_port_speed port_speed) 736 { 737 void __iomem *base = phy->regs; 738 u32 val; 739 740 val = readl_relaxed(base + UTMIP_MISC_CFG0); 741 val &= ~UTMIP_DPDM_OBSERVE_SEL(~0); 742 if (port_speed == TEGRA_USB_PHY_PORT_SPEED_LOW) 743 val |= UTMIP_DPDM_OBSERVE_SEL_FS_K; 744 else 745 val |= UTMIP_DPDM_OBSERVE_SEL_FS_J; 746 writel_relaxed(val, base + UTMIP_MISC_CFG0); 747 usleep_range(1, 10); 748 749 val = readl_relaxed(base + UTMIP_MISC_CFG0); 750 val |= UTMIP_DPDM_OBSERVE; 751 writel_relaxed(val, base + UTMIP_MISC_CFG0); 752 usleep_range(10, 100); 753 } 754 755 static void utmi_phy_restore_end(struct tegra_usb_phy *phy) 756 { 757 void __iomem *base = phy->regs; 758 u32 val; 759 760 val = readl_relaxed(base + UTMIP_MISC_CFG0); 761 val &= ~UTMIP_DPDM_OBSERVE; 762 writel_relaxed(val, base + UTMIP_MISC_CFG0); 763 usleep_range(10, 100); 764 } 765 766 static int ulpi_phy_power_on(struct tegra_usb_phy *phy) 767 { 768 void __iomem *base = phy->regs; 769 u32 val; 770 int err; 771 772 gpiod_set_value_cansleep(phy->reset_gpio, 1); 773 774 err = clk_prepare_enable(phy->clk); 775 if (err) 776 return err; 777 778 usleep_range(5000, 6000); 779 780 gpiod_set_value_cansleep(phy->reset_gpio, 0); 781 782 usleep_range(1000, 2000); 783 784 val = readl_relaxed(base + USB_SUSP_CTRL); 785 val |= UHSIC_RESET; 786 writel_relaxed(val, base + USB_SUSP_CTRL); 787 788 val = readl_relaxed(base + ULPI_TIMING_CTRL_0); 789 val |= ULPI_OUTPUT_PINMUX_BYP | ULPI_CLKOUT_PINMUX_BYP; 790 writel_relaxed(val, base + ULPI_TIMING_CTRL_0); 791 792 val = readl_relaxed(base + USB_SUSP_CTRL); 793 val |= ULPI_PHY_ENABLE; 794 writel_relaxed(val, base + USB_SUSP_CTRL); 795 796 val = 0; 797 writel_relaxed(val, base + ULPI_TIMING_CTRL_1); 798 799 val |= ULPI_DATA_TRIMMER_SEL(4); 800 val |= ULPI_STPDIRNXT_TRIMMER_SEL(4); 801 val |= ULPI_DIR_TRIMMER_SEL(4); 802 writel_relaxed(val, base + ULPI_TIMING_CTRL_1); 803 usleep_range(10, 100); 804 805 val |= ULPI_DATA_TRIMMER_LOAD; 806 val |= ULPI_STPDIRNXT_TRIMMER_LOAD; 807 val |= ULPI_DIR_TRIMMER_LOAD; 808 writel_relaxed(val, base + ULPI_TIMING_CTRL_1); 809 810 /* Fix VbusInvalid due to floating VBUS */ 811 err = usb_phy_io_write(phy->ulpi, 0x40, 0x08); 812 if (err) { 813 dev_err(phy->u_phy.dev, "ULPI write failed: %d\n", err); 814 goto disable_clk; 815 } 816 817 err = usb_phy_io_write(phy->ulpi, 0x80, 0x0B); 818 if (err) { 819 dev_err(phy->u_phy.dev, "ULPI write failed: %d\n", err); 820 goto disable_clk; 821 } 822 823 val = readl_relaxed(base + USB_SUSP_CTRL); 824 val |= USB_SUSP_CLR; 825 writel_relaxed(val, base + USB_SUSP_CTRL); 826 usleep_range(100, 1000); 827 828 val = readl_relaxed(base + USB_SUSP_CTRL); 829 val &= ~USB_SUSP_CLR; 830 writel_relaxed(val, base + USB_SUSP_CTRL); 831 832 return 0; 833 834 disable_clk: 835 clk_disable_unprepare(phy->clk); 836 837 return err; 838 } 839 840 static int ulpi_phy_power_off(struct tegra_usb_phy *phy) 841 { 842 gpiod_set_value_cansleep(phy->reset_gpio, 1); 843 usleep_range(5000, 6000); 844 clk_disable_unprepare(phy->clk); 845 846 /* 847 * Wakeup currently unimplemented for ULPI, thus PHY needs to be 848 * force-resumed. 849 */ 850 if (WARN_ON_ONCE(phy->wakeup_enabled)) { 851 ulpi_phy_power_on(phy); 852 return -EOPNOTSUPP; 853 } 854 855 return 0; 856 } 857 858 static int tegra_usb_phy_power_on(struct tegra_usb_phy *phy) 859 { 860 int err; 861 862 if (phy->powered_on) 863 return 0; 864 865 if (phy->is_ulpi_phy) 866 err = ulpi_phy_power_on(phy); 867 else 868 err = utmi_phy_power_on(phy); 869 if (err) 870 return err; 871 872 phy->powered_on = true; 873 874 /* Let PHY settle down */ 875 usleep_range(2000, 2500); 876 877 return 0; 878 } 879 880 static int tegra_usb_phy_power_off(struct tegra_usb_phy *phy) 881 { 882 int err; 883 884 if (!phy->powered_on) 885 return 0; 886 887 if (phy->is_ulpi_phy) 888 err = ulpi_phy_power_off(phy); 889 else 890 err = utmi_phy_power_off(phy); 891 if (err) 892 return err; 893 894 phy->powered_on = false; 895 896 return 0; 897 } 898 899 static void tegra_usb_phy_shutdown(struct usb_phy *u_phy) 900 { 901 struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); 902 903 if (WARN_ON(!phy->freq)) 904 return; 905 906 usb_phy_set_wakeup(u_phy, false); 907 tegra_usb_phy_power_off(phy); 908 909 if (!phy->is_ulpi_phy) 910 utmip_pad_close(phy); 911 912 regulator_disable(phy->vbus); 913 clk_disable_unprepare(phy->pll_u); 914 915 phy->freq = NULL; 916 } 917 918 static irqreturn_t tegra_usb_phy_isr(int irq, void *data) 919 { 920 u32 val, int_mask = ID_CHG_DET | VBUS_WAKEUP_CHG_DET; 921 struct tegra_usb_phy *phy = data; 922 void __iomem *base = phy->regs; 923 924 /* 925 * The PHY interrupt also wakes the USB controller driver since 926 * interrupt is shared. We don't do anything in the PHY driver, 927 * so just clear the interrupt. 928 */ 929 val = readl_relaxed(base + USB_PHY_VBUS_WAKEUP_ID); 930 writel_relaxed(val, base + USB_PHY_VBUS_WAKEUP_ID); 931 932 return val & int_mask ? IRQ_HANDLED : IRQ_NONE; 933 } 934 935 static int tegra_usb_phy_set_wakeup(struct usb_phy *u_phy, bool enable) 936 { 937 struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); 938 void __iomem *base = phy->regs; 939 int ret = 0; 940 u32 val; 941 942 if (phy->wakeup_enabled && phy->mode != USB_DR_MODE_HOST && 943 phy->irq > 0) { 944 disable_irq(phy->irq); 945 946 val = readl_relaxed(base + USB_PHY_VBUS_WAKEUP_ID); 947 val &= ~(ID_INT_EN | VBUS_WAKEUP_INT_EN); 948 writel_relaxed(val, base + USB_PHY_VBUS_WAKEUP_ID); 949 950 enable_irq(phy->irq); 951 952 free_irq(phy->irq, phy); 953 954 phy->wakeup_enabled = false; 955 } 956 957 if (enable && phy->mode != USB_DR_MODE_HOST && phy->irq > 0) { 958 ret = request_irq(phy->irq, tegra_usb_phy_isr, IRQF_SHARED, 959 dev_name(phy->u_phy.dev), phy); 960 if (!ret) { 961 disable_irq(phy->irq); 962 963 /* 964 * USB clock will be resumed once wake event will be 965 * generated. The ID-change event requires to have 966 * interrupts enabled, otherwise it won't be generated. 967 */ 968 val = readl_relaxed(base + USB_PHY_VBUS_WAKEUP_ID); 969 val |= ID_INT_EN | VBUS_WAKEUP_INT_EN; 970 writel_relaxed(val, base + USB_PHY_VBUS_WAKEUP_ID); 971 972 enable_irq(phy->irq); 973 } else { 974 dev_err(phy->u_phy.dev, 975 "Failed to request interrupt: %d", ret); 976 enable = false; 977 } 978 } 979 980 phy->wakeup_enabled = enable; 981 982 return ret; 983 } 984 985 static int tegra_usb_phy_set_suspend(struct usb_phy *u_phy, int suspend) 986 { 987 struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); 988 int ret; 989 990 if (WARN_ON(!phy->freq)) 991 return -EINVAL; 992 993 /* 994 * PHY is sharing IRQ with the CI driver, hence here we either 995 * disable interrupt for both PHY and CI or for CI only. The 996 * interrupt needs to be disabled while hardware is reprogrammed 997 * because interrupt touches the programmed registers, and thus, 998 * there could be a race condition. 999 */ 1000 if (phy->irq > 0) 1001 disable_irq(phy->irq); 1002 1003 if (suspend) 1004 ret = tegra_usb_phy_power_off(phy); 1005 else 1006 ret = tegra_usb_phy_power_on(phy); 1007 1008 if (phy->irq > 0) 1009 enable_irq(phy->irq); 1010 1011 return ret; 1012 } 1013 1014 static int tegra_usb_phy_configure_pmc(struct tegra_usb_phy *phy) 1015 { 1016 int err, val = 0; 1017 1018 /* older device-trees don't have PMC regmap */ 1019 if (!phy->pmc_regmap) 1020 return 0; 1021 1022 /* 1023 * Tegra20 has a different layout of PMC USB register bits and AO is 1024 * enabled by default after system reset on Tegra20, so assume nothing 1025 * to do on Tegra20. 1026 */ 1027 if (!phy->soc_config->requires_pmc_ao_power_up) 1028 return 0; 1029 1030 /* enable VBUS wake-up detector */ 1031 if (phy->mode != USB_DR_MODE_HOST) 1032 val |= VBUS_WAKEUP_PD_P0 << phy->instance * 4; 1033 1034 /* enable ID-pin ACC detector for OTG mode switching */ 1035 if (phy->mode == USB_DR_MODE_OTG) 1036 val |= ID_PD_P0 << phy->instance * 4; 1037 1038 /* disable detectors to reset them */ 1039 err = regmap_set_bits(phy->pmc_regmap, PMC_USB_AO, val); 1040 if (err) { 1041 dev_err(phy->u_phy.dev, "Failed to disable PMC AO: %d\n", err); 1042 return err; 1043 } 1044 1045 usleep_range(10, 100); 1046 1047 /* enable detectors */ 1048 err = regmap_clear_bits(phy->pmc_regmap, PMC_USB_AO, val); 1049 if (err) { 1050 dev_err(phy->u_phy.dev, "Failed to enable PMC AO: %d\n", err); 1051 return err; 1052 } 1053 1054 /* detectors starts to work after 10ms */ 1055 usleep_range(10000, 15000); 1056 1057 return 0; 1058 } 1059 1060 static int tegra_usb_phy_init(struct usb_phy *u_phy) 1061 { 1062 struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); 1063 unsigned long parent_rate; 1064 unsigned int i; 1065 int err; 1066 1067 if (WARN_ON(phy->freq)) 1068 return 0; 1069 1070 err = clk_prepare_enable(phy->pll_u); 1071 if (err) 1072 return err; 1073 1074 parent_rate = clk_get_rate(clk_get_parent(phy->pll_u)); 1075 for (i = 0; i < ARRAY_SIZE(tegra_freq_table); i++) { 1076 if (tegra_freq_table[i].freq == parent_rate) { 1077 phy->freq = &tegra_freq_table[i]; 1078 break; 1079 } 1080 } 1081 if (!phy->freq) { 1082 dev_err(phy->u_phy.dev, "Invalid pll_u parent rate %ld\n", 1083 parent_rate); 1084 err = -EINVAL; 1085 goto disable_clk; 1086 } 1087 1088 err = regulator_enable(phy->vbus); 1089 if (err) { 1090 dev_err(phy->u_phy.dev, 1091 "Failed to enable USB VBUS regulator: %d\n", err); 1092 goto disable_clk; 1093 } 1094 1095 if (!phy->is_ulpi_phy) { 1096 err = utmip_pad_open(phy); 1097 if (err) 1098 goto disable_vbus; 1099 } 1100 1101 err = tegra_usb_phy_configure_pmc(phy); 1102 if (err) 1103 goto close_phy; 1104 1105 err = tegra_usb_phy_power_on(phy); 1106 if (err) 1107 goto close_phy; 1108 1109 return 0; 1110 1111 close_phy: 1112 if (!phy->is_ulpi_phy) 1113 utmip_pad_close(phy); 1114 1115 disable_vbus: 1116 regulator_disable(phy->vbus); 1117 1118 disable_clk: 1119 clk_disable_unprepare(phy->pll_u); 1120 1121 phy->freq = NULL; 1122 1123 return err; 1124 } 1125 1126 void tegra_usb_phy_preresume(struct usb_phy *u_phy) 1127 { 1128 struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); 1129 1130 if (!phy->is_ulpi_phy) 1131 utmi_phy_preresume(phy); 1132 } 1133 EXPORT_SYMBOL_GPL(tegra_usb_phy_preresume); 1134 1135 void tegra_usb_phy_postresume(struct usb_phy *u_phy) 1136 { 1137 struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); 1138 1139 if (!phy->is_ulpi_phy) 1140 utmi_phy_postresume(phy); 1141 } 1142 EXPORT_SYMBOL_GPL(tegra_usb_phy_postresume); 1143 1144 void tegra_ehci_phy_restore_start(struct usb_phy *u_phy, 1145 enum tegra_usb_phy_port_speed port_speed) 1146 { 1147 struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); 1148 1149 if (!phy->is_ulpi_phy) 1150 utmi_phy_restore_start(phy, port_speed); 1151 } 1152 EXPORT_SYMBOL_GPL(tegra_ehci_phy_restore_start); 1153 1154 void tegra_ehci_phy_restore_end(struct usb_phy *u_phy) 1155 { 1156 struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); 1157 1158 if (!phy->is_ulpi_phy) 1159 utmi_phy_restore_end(phy); 1160 } 1161 EXPORT_SYMBOL_GPL(tegra_ehci_phy_restore_end); 1162 1163 static int read_utmi_param(struct platform_device *pdev, const char *param, 1164 u8 *dest) 1165 { 1166 u32 value; 1167 int err; 1168 1169 err = of_property_read_u32(pdev->dev.of_node, param, &value); 1170 if (err) 1171 dev_err(&pdev->dev, 1172 "Failed to read USB UTMI parameter %s: %d\n", 1173 param, err); 1174 else 1175 *dest = value; 1176 1177 return err; 1178 } 1179 1180 static int utmi_phy_probe(struct tegra_usb_phy *tegra_phy, 1181 struct platform_device *pdev) 1182 { 1183 struct tegra_utmip_config *config; 1184 struct resource *res; 1185 int err; 1186 1187 tegra_phy->is_ulpi_phy = false; 1188 1189 res = platform_get_resource(pdev, IORESOURCE_MEM, 1); 1190 if (!res) { 1191 dev_err(&pdev->dev, "Failed to get UTMI pad regs\n"); 1192 return -ENXIO; 1193 } 1194 1195 /* 1196 * Note that UTMI pad registers are shared by all PHYs, therefore 1197 * devm_platform_ioremap_resource() can't be used here. 1198 */ 1199 tegra_phy->pad_regs = devm_ioremap(&pdev->dev, res->start, 1200 resource_size(res)); 1201 if (!tegra_phy->pad_regs) { 1202 dev_err(&pdev->dev, "Failed to remap UTMI pad regs\n"); 1203 return -ENOMEM; 1204 } 1205 1206 tegra_phy->config = devm_kzalloc(&pdev->dev, sizeof(*config), 1207 GFP_KERNEL); 1208 if (!tegra_phy->config) 1209 return -ENOMEM; 1210 1211 config = tegra_phy->config; 1212 1213 err = read_utmi_param(pdev, "nvidia,hssync-start-delay", 1214 &config->hssync_start_delay); 1215 if (err) 1216 return err; 1217 1218 err = read_utmi_param(pdev, "nvidia,elastic-limit", 1219 &config->elastic_limit); 1220 if (err) 1221 return err; 1222 1223 err = read_utmi_param(pdev, "nvidia,idle-wait-delay", 1224 &config->idle_wait_delay); 1225 if (err) 1226 return err; 1227 1228 err = read_utmi_param(pdev, "nvidia,term-range-adj", 1229 &config->term_range_adj); 1230 if (err) 1231 return err; 1232 1233 err = read_utmi_param(pdev, "nvidia,xcvr-lsfslew", 1234 &config->xcvr_lsfslew); 1235 if (err) 1236 return err; 1237 1238 err = read_utmi_param(pdev, "nvidia,xcvr-lsrslew", 1239 &config->xcvr_lsrslew); 1240 if (err) 1241 return err; 1242 1243 if (tegra_phy->soc_config->requires_extra_tuning_parameters) { 1244 err = read_utmi_param(pdev, "nvidia,xcvr-hsslew", 1245 &config->xcvr_hsslew); 1246 if (err) 1247 return err; 1248 1249 err = read_utmi_param(pdev, "nvidia,hssquelch-level", 1250 &config->hssquelch_level); 1251 if (err) 1252 return err; 1253 1254 err = read_utmi_param(pdev, "nvidia,hsdiscon-level", 1255 &config->hsdiscon_level); 1256 if (err) 1257 return err; 1258 } 1259 1260 config->xcvr_setup_use_fuses = of_property_read_bool( 1261 pdev->dev.of_node, "nvidia,xcvr-setup-use-fuses"); 1262 1263 if (!config->xcvr_setup_use_fuses) { 1264 err = read_utmi_param(pdev, "nvidia,xcvr-setup", 1265 &config->xcvr_setup); 1266 if (err) 1267 return err; 1268 } 1269 1270 return 0; 1271 } 1272 1273 static void tegra_usb_phy_put_pmc_device(void *dev) 1274 { 1275 put_device(dev); 1276 } 1277 1278 static int tegra_usb_phy_parse_pmc(struct device *dev, 1279 struct tegra_usb_phy *phy) 1280 { 1281 struct platform_device *pmc_pdev; 1282 struct of_phandle_args args; 1283 int err; 1284 1285 err = of_parse_phandle_with_fixed_args(dev->of_node, "nvidia,pmc", 1286 1, 0, &args); 1287 if (err) { 1288 if (err != -ENOENT) 1289 return err; 1290 1291 dev_warn_once(dev, "nvidia,pmc is missing, please update your device-tree\n"); 1292 return 0; 1293 } 1294 1295 pmc_pdev = of_find_device_by_node(args.np); 1296 of_node_put(args.np); 1297 if (!pmc_pdev) 1298 return -ENODEV; 1299 1300 err = devm_add_action_or_reset(dev, tegra_usb_phy_put_pmc_device, 1301 &pmc_pdev->dev); 1302 if (err) 1303 return err; 1304 1305 if (!platform_get_drvdata(pmc_pdev)) 1306 return -EPROBE_DEFER; 1307 1308 phy->pmc_regmap = dev_get_regmap(&pmc_pdev->dev, "usb_sleepwalk"); 1309 if (!phy->pmc_regmap) 1310 return -EINVAL; 1311 1312 phy->instance = args.args[0]; 1313 1314 return 0; 1315 } 1316 1317 static const struct tegra_phy_soc_config tegra20_soc_config = { 1318 .utmi_pll_config_in_car_module = false, 1319 .has_hostpc = false, 1320 .requires_usbmode_setup = false, 1321 .requires_extra_tuning_parameters = false, 1322 .requires_pmc_ao_power_up = false, 1323 }; 1324 1325 static const struct tegra_phy_soc_config tegra30_soc_config = { 1326 .utmi_pll_config_in_car_module = true, 1327 .has_hostpc = true, 1328 .requires_usbmode_setup = true, 1329 .requires_extra_tuning_parameters = true, 1330 .requires_pmc_ao_power_up = true, 1331 }; 1332 1333 static const struct of_device_id tegra_usb_phy_id_table[] = { 1334 { .compatible = "nvidia,tegra30-usb-phy", .data = &tegra30_soc_config }, 1335 { .compatible = "nvidia,tegra20-usb-phy", .data = &tegra20_soc_config }, 1336 { }, 1337 }; 1338 MODULE_DEVICE_TABLE(of, tegra_usb_phy_id_table); 1339 1340 static int tegra_usb_phy_probe(struct platform_device *pdev) 1341 { 1342 struct device_node *np = pdev->dev.of_node; 1343 struct tegra_usb_phy *tegra_phy; 1344 enum usb_phy_interface phy_type; 1345 struct reset_control *reset; 1346 struct gpio_desc *gpiod; 1347 struct resource *res; 1348 struct usb_phy *phy; 1349 int err; 1350 1351 tegra_phy = devm_kzalloc(&pdev->dev, sizeof(*tegra_phy), GFP_KERNEL); 1352 if (!tegra_phy) 1353 return -ENOMEM; 1354 1355 tegra_phy->soc_config = of_device_get_match_data(&pdev->dev); 1356 tegra_phy->irq = platform_get_irq_optional(pdev, 0); 1357 1358 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1359 if (!res) { 1360 dev_err(&pdev->dev, "Failed to get I/O memory\n"); 1361 return -ENXIO; 1362 } 1363 1364 /* 1365 * Note that PHY and USB controller are using shared registers, 1366 * therefore devm_platform_ioremap_resource() can't be used here. 1367 */ 1368 tegra_phy->regs = devm_ioremap(&pdev->dev, res->start, 1369 resource_size(res)); 1370 if (!tegra_phy->regs) { 1371 dev_err(&pdev->dev, "Failed to remap I/O memory\n"); 1372 return -ENOMEM; 1373 } 1374 1375 tegra_phy->is_legacy_phy = 1376 of_property_read_bool(np, "nvidia,has-legacy-mode"); 1377 1378 if (of_property_present(np, "dr_mode")) 1379 tegra_phy->mode = usb_get_dr_mode(&pdev->dev); 1380 else 1381 tegra_phy->mode = USB_DR_MODE_HOST; 1382 1383 if (tegra_phy->mode == USB_DR_MODE_UNKNOWN) { 1384 dev_err(&pdev->dev, "dr_mode is invalid\n"); 1385 return -EINVAL; 1386 } 1387 1388 /* On some boards, the VBUS regulator doesn't need to be controlled */ 1389 tegra_phy->vbus = devm_regulator_get(&pdev->dev, "vbus"); 1390 if (IS_ERR(tegra_phy->vbus)) 1391 return PTR_ERR(tegra_phy->vbus); 1392 1393 tegra_phy->pll_u = devm_clk_get(&pdev->dev, "pll_u"); 1394 err = PTR_ERR_OR_ZERO(tegra_phy->pll_u); 1395 if (err) { 1396 dev_err(&pdev->dev, "Failed to get pll_u clock: %d\n", err); 1397 return err; 1398 } 1399 1400 err = tegra_usb_phy_parse_pmc(&pdev->dev, tegra_phy); 1401 if (err) { 1402 dev_err_probe(&pdev->dev, err, "Failed to get PMC regmap\n"); 1403 return err; 1404 } 1405 1406 phy_type = of_usb_get_phy_mode(np); 1407 switch (phy_type) { 1408 case USBPHY_INTERFACE_MODE_UTMI: 1409 err = utmi_phy_probe(tegra_phy, pdev); 1410 if (err) 1411 return err; 1412 1413 tegra_phy->pad_clk = devm_clk_get(&pdev->dev, "utmi-pads"); 1414 err = PTR_ERR_OR_ZERO(tegra_phy->pad_clk); 1415 if (err) { 1416 dev_err(&pdev->dev, 1417 "Failed to get UTMIP pad clock: %d\n", err); 1418 return err; 1419 } 1420 1421 reset = devm_reset_control_get_optional_shared(&pdev->dev, 1422 "utmi-pads"); 1423 err = PTR_ERR_OR_ZERO(reset); 1424 if (err) { 1425 dev_err(&pdev->dev, 1426 "Failed to get UTMI-pads reset: %d\n", err); 1427 return err; 1428 } 1429 tegra_phy->pad_rst = reset; 1430 break; 1431 1432 case USBPHY_INTERFACE_MODE_ULPI: 1433 tegra_phy->is_ulpi_phy = true; 1434 1435 tegra_phy->clk = devm_clk_get(&pdev->dev, "ulpi-link"); 1436 err = PTR_ERR_OR_ZERO(tegra_phy->clk); 1437 if (err) { 1438 dev_err(&pdev->dev, 1439 "Failed to get ULPI clock: %d\n", err); 1440 return err; 1441 } 1442 1443 gpiod = devm_gpiod_get(&pdev->dev, "nvidia,phy-reset", 1444 GPIOD_OUT_HIGH); 1445 err = PTR_ERR_OR_ZERO(gpiod); 1446 if (err) { 1447 dev_err(&pdev->dev, 1448 "Request failed for reset GPIO: %d\n", err); 1449 return err; 1450 } 1451 1452 err = gpiod_set_consumer_name(gpiod, "ulpi_phy_reset_b"); 1453 if (err) { 1454 dev_err(&pdev->dev, 1455 "Failed to set up reset GPIO name: %d\n", err); 1456 return err; 1457 } 1458 1459 tegra_phy->reset_gpio = gpiod; 1460 1461 phy = devm_otg_ulpi_create(&pdev->dev, 1462 &ulpi_viewport_access_ops, 0); 1463 if (!phy) { 1464 dev_err(&pdev->dev, "Failed to create ULPI OTG\n"); 1465 return -ENOMEM; 1466 } 1467 1468 tegra_phy->ulpi = phy; 1469 tegra_phy->ulpi->io_priv = tegra_phy->regs + ULPI_VIEWPORT; 1470 break; 1471 1472 default: 1473 dev_err(&pdev->dev, "phy_type %u is invalid or unsupported\n", 1474 phy_type); 1475 return -EINVAL; 1476 } 1477 1478 tegra_phy->u_phy.dev = &pdev->dev; 1479 tegra_phy->u_phy.init = tegra_usb_phy_init; 1480 tegra_phy->u_phy.shutdown = tegra_usb_phy_shutdown; 1481 tegra_phy->u_phy.set_wakeup = tegra_usb_phy_set_wakeup; 1482 tegra_phy->u_phy.set_suspend = tegra_usb_phy_set_suspend; 1483 1484 platform_set_drvdata(pdev, tegra_phy); 1485 1486 return usb_add_phy_dev(&tegra_phy->u_phy); 1487 } 1488 1489 static void tegra_usb_phy_remove(struct platform_device *pdev) 1490 { 1491 struct tegra_usb_phy *tegra_phy = platform_get_drvdata(pdev); 1492 1493 usb_remove_phy(&tegra_phy->u_phy); 1494 } 1495 1496 static struct platform_driver tegra_usb_phy_driver = { 1497 .probe = tegra_usb_phy_probe, 1498 .remove_new = tegra_usb_phy_remove, 1499 .driver = { 1500 .name = "tegra-phy", 1501 .of_match_table = tegra_usb_phy_id_table, 1502 }, 1503 }; 1504 module_platform_driver(tegra_usb_phy_driver); 1505 1506 MODULE_DESCRIPTION("Tegra USB PHY driver"); 1507 MODULE_LICENSE("GPL v2"); 1508