1# 2# Physical Layer USB driver configuration 3# 4menu "USB Physical Layer drivers" 5 6config USB_PHY 7 def_bool n 8 9# 10# USB Transceiver Drivers 11# 12config AB8500_USB 13 tristate "AB8500 USB Transceiver Driver" 14 depends on AB8500_CORE 15 select USB_PHY 16 help 17 Enable this to support the USB OTG transceiver in AB8500 chip. 18 This transceiver supports high and full speed devices plus, 19 in host mode, low speed. 20 21config FSL_USB2_OTG 22 bool "Freescale USB OTG Transceiver Driver" 23 depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM_RUNTIME 24 select USB_OTG 25 select USB_PHY 26 help 27 Enable this to support Freescale USB OTG transceiver. 28 29config ISP1301_OMAP 30 tristate "Philips ISP1301 with OMAP OTG" 31 depends on I2C && ARCH_OMAP_OTG 32 depends on USB 33 select USB_PHY 34 help 35 If you say yes here you get support for the Philips ISP1301 36 USB-On-The-Go transceiver working with the OMAP OTG controller. 37 The ISP1301 is a full speed USB transceiver which is used in 38 products including H2, H3, and H4 development boards for Texas 39 Instruments OMAP processors. 40 41 This driver can also be built as a module. If so, the module 42 will be called phy-isp1301-omap. 43 44config KEYSTONE_USB_PHY 45 tristate "Keystone USB PHY Driver" 46 depends on ARCH_KEYSTONE || COMPILE_TEST 47 select NOP_USB_XCEIV 48 help 49 Enable this to support Keystone USB phy. This driver provides 50 interface to interact with USB 2.0 and USB 3.0 PHY that is part 51 of the Keystone SOC. 52 53config NOP_USB_XCEIV 54 tristate "NOP USB Transceiver Driver" 55 select USB_PHY 56 help 57 This driver is to be used by all the usb transceiver which are either 58 built-in with usb ip or which are autonomous and doesn't require any 59 phy programming such as ISP1x04 etc. 60 61config AM335X_CONTROL_USB 62 tristate 63 64config AM335X_PHY_USB 65 tristate "AM335x USB PHY Driver" 66 depends on ARM || COMPILE_TEST 67 select USB_PHY 68 select AM335X_CONTROL_USB 69 select NOP_USB_XCEIV 70 help 71 This driver provides PHY support for that phy which part for the 72 AM335x SoC. 73 74config SAMSUNG_USBPHY 75 tristate 76 help 77 Enable this to support Samsung USB phy helper driver for Samsung SoCs. 78 This driver provides common interface to interact, for Samsung USB 2.0 PHY 79 driver and later for Samsung USB 3.0 PHY driver. 80 81config SAMSUNG_USB2PHY 82 tristate "Samsung USB 2.0 PHY controller Driver" 83 select SAMSUNG_USBPHY 84 select USB_PHY 85 help 86 Enable this to support Samsung USB 2.0 (High Speed) PHY controller 87 driver for Samsung SoCs. 88 89config SAMSUNG_USB3PHY 90 tristate "Samsung USB 3.0 PHY controller Driver" 91 select SAMSUNG_USBPHY 92 select USB_PHY 93 help 94 Enable this to support Samsung USB 3.0 (Super Speed) phy controller 95 for samsung SoCs. 96 97config TWL6030_USB 98 tristate "TWL6030 USB Transceiver Driver" 99 depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS 100 help 101 Enable this to support the USB OTG transceiver on TWL6030 102 family chips. This TWL6030 transceiver has the VBUS and ID GND 103 and OTG SRP events capabilities. For all other transceiver functionality 104 UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs 105 are hooked to this driver through platform_data structure. 106 The definition of internal PHY APIs are in the mach-omap2 layer. 107 108config USB_GPIO_VBUS 109 tristate "GPIO based peripheral-only VBUS sensing 'transceiver'" 110 depends on GPIOLIB 111 select USB_PHY 112 help 113 Provides simple GPIO VBUS sensing for controllers with an 114 internal transceiver via the usb_phy interface, and 115 optionally control of a D+ pullup GPIO as well as a VBUS 116 current limit regulator. 117 118config OMAP_OTG 119 tristate "OMAP USB OTG controller driver" 120 depends on ARCH_OMAP_OTG && EXTCON 121 help 122 Enable this to support some transceivers on OMAP1 platforms. OTG 123 controller is needed to switch between host and peripheral modes. 124 125 This driver can also be built as a module. If so, the module 126 will be called phy-omap-otg. 127 128config TAHVO_USB 129 tristate "Tahvo USB transceiver driver" 130 depends on MFD_RETU && EXTCON 131 select USB_PHY 132 help 133 Enable this to support USB transceiver on Tahvo. This is used 134 at least on Nokia 770. 135 136config TAHVO_USB_HOST_BY_DEFAULT 137 depends on TAHVO_USB 138 boolean "Device in USB host mode by default" 139 help 140 Say Y here, if you want the device to enter USB host mode 141 by default on bootup. 142 143config USB_ISP1301 144 tristate "NXP ISP1301 USB transceiver support" 145 depends on USB || USB_GADGET 146 depends on I2C 147 select USB_PHY 148 help 149 Say Y here to add support for the NXP ISP1301 USB transceiver driver. 150 This chip is typically used as USB transceiver for USB host, gadget 151 and OTG drivers (to be selected separately). 152 153 To compile this driver as a module, choose M here: the 154 module will be called phy-isp1301. 155 156config USB_MSM_OTG 157 tristate "Qualcomm on-chip USB OTG controller support" 158 depends on (USB || USB_GADGET) && (ARCH_MSM || ARCH_QCOM || COMPILE_TEST) 159 depends on RESET_CONTROLLER 160 select USB_PHY 161 help 162 Enable this to support the USB OTG transceiver on Qualcomm chips. It 163 handles PHY initialization, clock management, and workarounds 164 required after resetting the hardware and power management. 165 This driver is required even for peripheral only or host only 166 mode configurations. 167 This driver is not supported on boards like trout which 168 has an external PHY. 169 170config USB_MV_OTG 171 tristate "Marvell USB OTG support" 172 depends on USB_EHCI_MV && USB_MV_UDC && PM_RUNTIME 173 select USB_OTG 174 select USB_PHY 175 help 176 Say Y here if you want to build Marvell USB OTG transciever 177 driver in kernel (including PXA and MMP series). This driver 178 implements role switch between EHCI host driver and gadget driver. 179 180 To compile this driver as a module, choose M here. 181 182config USB_MXS_PHY 183 tristate "Freescale MXS USB PHY support" 184 depends on ARCH_MXC || ARCH_MXS 185 select STMP_DEVICE 186 select USB_PHY 187 help 188 Enable this to support the Freescale MXS USB PHY. 189 190 MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x. 191 192config USB_RCAR_PHY 193 tristate "Renesas R-Car USB PHY support" 194 depends on USB || USB_GADGET 195 depends on ARCH_R8A7778 || ARCH_R8A7779 || COMPILE_TEST 196 select USB_PHY 197 help 198 Say Y here to add support for the Renesas R-Car USB common PHY driver. 199 This chip is typically used as USB PHY for USB host, gadget. 200 This driver supports R8A7778 and R8A7779. 201 202 To compile this driver as a module, choose M here: the 203 module will be called phy-rcar-usb. 204 205config USB_RCAR_GEN2_PHY 206 tristate "Renesas R-Car Gen2 USB PHY support" 207 depends on ARCH_R8A7790 || ARCH_R8A7791 || COMPILE_TEST 208 select USB_PHY 209 help 210 Say Y here to add support for the Renesas R-Car Gen2 USB PHY driver. 211 It is typically used to control internal USB PHY for USBHS, 212 and to configure shared USB channels 0 and 2. 213 This driver supports R8A7790 and R8A7791. 214 215 To compile this driver as a module, choose M here: the 216 module will be called phy-rcar-gen2-usb. 217 218config USB_ULPI 219 bool "Generic ULPI Transceiver Driver" 220 depends on ARM || ARM64 221 help 222 Enable this to support ULPI connected USB OTG transceivers which 223 are likely found on embedded boards. 224 225config USB_ULPI_VIEWPORT 226 bool 227 depends on USB_ULPI 228 help 229 Provides read/write operations to the ULPI phy register set for 230 controllers with a viewport register (e.g. Chipidea/ARC controllers). 231 232endmenu 233