1# 2# Physical Layer USB driver configuration 3# 4menu "USB Physical Layer drivers" 5 6config USB_PHY 7 def_bool n 8 9# 10# USB Transceiver Drivers 11# 12config AB8500_USB 13 tristate "AB8500 USB Transceiver Driver" 14 depends on AB8500_CORE 15 select USB_PHY 16 help 17 Enable this to support the USB OTG transceiver in AB8500 chip. 18 This transceiver supports high and full speed devices plus, 19 in host mode, low speed. 20 21config FSL_USB2_OTG 22 bool "Freescale USB OTG Transceiver Driver" 23 depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM 24 select USB_OTG 25 select USB_PHY 26 help 27 Enable this to support Freescale USB OTG transceiver. 28 29config ISP1301_OMAP 30 tristate "Philips ISP1301 with OMAP OTG" 31 depends on I2C && ARCH_OMAP_OTG 32 depends on USB 33 select USB_PHY 34 help 35 If you say yes here you get support for the Philips ISP1301 36 USB-On-The-Go transceiver working with the OMAP OTG controller. 37 The ISP1301 is a full speed USB transceiver which is used in 38 products including H2, H3, and H4 development boards for Texas 39 Instruments OMAP processors. 40 41 This driver can also be built as a module. If so, the module 42 will be called phy-isp1301-omap. 43 44config KEYSTONE_USB_PHY 45 tristate "Keystone USB PHY Driver" 46 depends on ARCH_KEYSTONE || COMPILE_TEST 47 select NOP_USB_XCEIV 48 help 49 Enable this to support Keystone USB phy. This driver provides 50 interface to interact with USB 2.0 and USB 3.0 PHY that is part 51 of the Keystone SOC. 52 53config NOP_USB_XCEIV 54 tristate "NOP USB Transceiver Driver" 55 select USB_PHY 56 help 57 This driver is to be used by all the usb transceiver which are either 58 built-in with usb ip or which are autonomous and doesn't require any 59 phy programming such as ISP1x04 etc. 60 61config AM335X_CONTROL_USB 62 tristate 63 64config AM335X_PHY_USB 65 tristate "AM335x USB PHY Driver" 66 depends on ARM || COMPILE_TEST 67 select USB_PHY 68 select AM335X_CONTROL_USB 69 select NOP_USB_XCEIV 70 help 71 This driver provides PHY support for that phy which part for the 72 AM335x SoC. 73 74config SAMSUNG_USBPHY 75 tristate 76 help 77 Enable this to support Samsung USB phy helper driver for Samsung SoCs. 78 This driver provides common interface to interact, for Samsung USB 2.0 PHY 79 driver and later for Samsung USB 3.0 PHY driver. 80 81config TWL6030_USB 82 tristate "TWL6030 USB Transceiver Driver" 83 depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS 84 help 85 Enable this to support the USB OTG transceiver on TWL6030 86 family chips. This TWL6030 transceiver has the VBUS and ID GND 87 and OTG SRP events capabilities. For all other transceiver functionality 88 UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs 89 are hooked to this driver through platform_data structure. 90 The definition of internal PHY APIs are in the mach-omap2 layer. 91 92config USB_GPIO_VBUS 93 tristate "GPIO based peripheral-only VBUS sensing 'transceiver'" 94 depends on GPIOLIB 95 select USB_PHY 96 help 97 Provides simple GPIO VBUS sensing for controllers with an 98 internal transceiver via the usb_phy interface, and 99 optionally control of a D+ pullup GPIO as well as a VBUS 100 current limit regulator. 101 102config OMAP_OTG 103 tristate "OMAP USB OTG controller driver" 104 depends on ARCH_OMAP_OTG && EXTCON 105 help 106 Enable this to support some transceivers on OMAP1 platforms. OTG 107 controller is needed to switch between host and peripheral modes. 108 109 This driver can also be built as a module. If so, the module 110 will be called phy-omap-otg. 111 112config TAHVO_USB 113 tristate "Tahvo USB transceiver driver" 114 depends on MFD_RETU && EXTCON 115 select USB_PHY 116 help 117 Enable this to support USB transceiver on Tahvo. This is used 118 at least on Nokia 770. 119 120config TAHVO_USB_HOST_BY_DEFAULT 121 depends on TAHVO_USB 122 bool "Device in USB host mode by default" 123 help 124 Say Y here, if you want the device to enter USB host mode 125 by default on bootup. 126 127config USB_ISP1301 128 tristate "NXP ISP1301 USB transceiver support" 129 depends on USB || USB_GADGET 130 depends on I2C 131 select USB_PHY 132 help 133 Say Y here to add support for the NXP ISP1301 USB transceiver driver. 134 This chip is typically used as USB transceiver for USB host, gadget 135 and OTG drivers (to be selected separately). 136 137 To compile this driver as a module, choose M here: the 138 module will be called phy-isp1301. 139 140config USB_MSM_OTG 141 tristate "Qualcomm on-chip USB OTG controller support" 142 depends on (USB || USB_GADGET) && (ARCH_MSM || ARCH_QCOM || COMPILE_TEST) 143 depends on RESET_CONTROLLER 144 select USB_PHY 145 help 146 Enable this to support the USB OTG transceiver on Qualcomm chips. It 147 handles PHY initialization, clock management, and workarounds 148 required after resetting the hardware and power management. 149 This driver is required even for peripheral only or host only 150 mode configurations. 151 This driver is not supported on boards like trout which 152 has an external PHY. 153 154config USB_MV_OTG 155 tristate "Marvell USB OTG support" 156 depends on USB_EHCI_MV && USB_MV_UDC && PM 157 select USB_OTG 158 select USB_PHY 159 help 160 Say Y here if you want to build Marvell USB OTG transciever 161 driver in kernel (including PXA and MMP series). This driver 162 implements role switch between EHCI host driver and gadget driver. 163 164 To compile this driver as a module, choose M here. 165 166config USB_MXS_PHY 167 tristate "Freescale MXS USB PHY support" 168 depends on ARCH_MXC || ARCH_MXS 169 select STMP_DEVICE 170 select USB_PHY 171 help 172 Enable this to support the Freescale MXS USB PHY. 173 174 MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x. 175 176config USB_RCAR_PHY 177 tristate "Renesas R-Car USB PHY support" 178 depends on USB || USB_GADGET 179 depends on ARCH_R8A7778 || ARCH_R8A7779 || COMPILE_TEST 180 select USB_PHY 181 help 182 Say Y here to add support for the Renesas R-Car USB common PHY driver. 183 This chip is typically used as USB PHY for USB host, gadget. 184 This driver supports R8A7778 and R8A7779. 185 186 To compile this driver as a module, choose M here: the 187 module will be called phy-rcar-usb. 188 189config USB_RCAR_GEN2_PHY 190 tristate "Renesas R-Car Gen2 USB PHY support" 191 depends on ARCH_R8A7790 || ARCH_R8A7791 || COMPILE_TEST 192 select USB_PHY 193 help 194 Say Y here to add support for the Renesas R-Car Gen2 USB PHY driver. 195 It is typically used to control internal USB PHY for USBHS, 196 and to configure shared USB channels 0 and 2. 197 This driver supports R8A7790 and R8A7791. 198 199 To compile this driver as a module, choose M here: the 200 module will be called phy-rcar-gen2-usb. 201 202config USB_ULPI 203 bool "Generic ULPI Transceiver Driver" 204 depends on ARM || ARM64 205 help 206 Enable this to support ULPI connected USB OTG transceivers which 207 are likely found on embedded boards. 208 209config USB_ULPI_VIEWPORT 210 bool 211 depends on USB_ULPI 212 help 213 Provides read/write operations to the ULPI phy register set for 214 controllers with a viewport register (e.g. Chipidea/ARC controllers). 215 216endmenu 217