1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * MUSB OTG driver host support 4 * 5 * Copyright 2005 Mentor Graphics Corporation 6 * Copyright (C) 2005-2006 by Texas Instruments 7 * Copyright (C) 2006-2007 Nokia Corporation 8 * Copyright (C) 2008-2009 MontaVista Software, Inc. <source@mvista.com> 9 */ 10 11 #include <linux/module.h> 12 #include <linux/kernel.h> 13 #include <linux/delay.h> 14 #include <linux/sched.h> 15 #include <linux/slab.h> 16 #include <linux/errno.h> 17 #include <linux/list.h> 18 #include <linux/dma-mapping.h> 19 20 #include "musb_core.h" 21 #include "musb_host.h" 22 #include "musb_trace.h" 23 24 /* MUSB HOST status 22-mar-2006 25 * 26 * - There's still lots of partial code duplication for fault paths, so 27 * they aren't handled as consistently as they need to be. 28 * 29 * - PIO mostly behaved when last tested. 30 * + including ep0, with all usbtest cases 9, 10 31 * + usbtest 14 (ep0out) doesn't seem to run at all 32 * + double buffered OUT/TX endpoints saw stalls(!) with certain usbtest 33 * configurations, but otherwise double buffering passes basic tests. 34 * + for 2.6.N, for N > ~10, needs API changes for hcd framework. 35 * 36 * - DMA (CPPI) ... partially behaves, not currently recommended 37 * + about 1/15 the speed of typical EHCI implementations (PCI) 38 * + RX, all too often reqpkt seems to misbehave after tx 39 * + TX, no known issues (other than evident silicon issue) 40 * 41 * - DMA (Mentor/OMAP) ...has at least toggle update problems 42 * 43 * - [23-feb-2009] minimal traffic scheduling to avoid bulk RX packet 44 * starvation ... nothing yet for TX, interrupt, or bulk. 45 * 46 * - Not tested with HNP, but some SRP paths seem to behave. 47 * 48 * NOTE 24-August-2006: 49 * 50 * - Bulk traffic finally uses both sides of hardware ep1, freeing up an 51 * extra endpoint for periodic use enabling hub + keybd + mouse. That 52 * mostly works, except that with "usbnet" it's easy to trigger cases 53 * with "ping" where RX loses. (a) ping to davinci, even "ping -f", 54 * fine; but (b) ping _from_ davinci, even "ping -c 1", ICMP RX loses 55 * although ARP RX wins. (That test was done with a full speed link.) 56 */ 57 58 59 /* 60 * NOTE on endpoint usage: 61 * 62 * CONTROL transfers all go through ep0. BULK ones go through dedicated IN 63 * and OUT endpoints ... hardware is dedicated for those "async" queue(s). 64 * (Yes, bulk _could_ use more of the endpoints than that, and would even 65 * benefit from it.) 66 * 67 * INTERUPPT and ISOCHRONOUS transfers are scheduled to the other endpoints. 68 * So far that scheduling is both dumb and optimistic: the endpoint will be 69 * "claimed" until its software queue is no longer refilled. No multiplexing 70 * of transfers between endpoints, or anything clever. 71 */ 72 73 struct musb *hcd_to_musb(struct usb_hcd *hcd) 74 { 75 return *(struct musb **) hcd->hcd_priv; 76 } 77 78 79 static void musb_ep_program(struct musb *musb, u8 epnum, 80 struct urb *urb, int is_out, 81 u8 *buf, u32 offset, u32 len); 82 83 /* 84 * Clear TX fifo. Needed to avoid BABBLE errors. 85 */ 86 static void musb_h_tx_flush_fifo(struct musb_hw_ep *ep) 87 { 88 struct musb *musb = ep->musb; 89 void __iomem *epio = ep->regs; 90 u16 csr; 91 int retries = 1000; 92 93 csr = musb_readw(epio, MUSB_TXCSR); 94 while (csr & MUSB_TXCSR_FIFONOTEMPTY) { 95 csr |= MUSB_TXCSR_FLUSHFIFO | MUSB_TXCSR_TXPKTRDY; 96 musb_writew(epio, MUSB_TXCSR, csr); 97 csr = musb_readw(epio, MUSB_TXCSR); 98 99 /* 100 * FIXME: sometimes the tx fifo flush failed, it has been 101 * observed during device disconnect on AM335x. 102 * 103 * To reproduce the issue, ensure tx urb(s) are queued when 104 * unplug the usb device which is connected to AM335x usb 105 * host port. 106 * 107 * I found using a usb-ethernet device and running iperf 108 * (client on AM335x) has very high chance to trigger it. 109 * 110 * Better to turn on musb_dbg() in musb_cleanup_urb() with 111 * CPPI enabled to see the issue when aborting the tx channel. 112 */ 113 if (dev_WARN_ONCE(musb->controller, retries-- < 1, 114 "Could not flush host TX%d fifo: csr: %04x\n", 115 ep->epnum, csr)) 116 return; 117 mdelay(1); 118 } 119 } 120 121 static void musb_h_ep0_flush_fifo(struct musb_hw_ep *ep) 122 { 123 void __iomem *epio = ep->regs; 124 u16 csr; 125 int retries = 5; 126 127 /* scrub any data left in the fifo */ 128 do { 129 csr = musb_readw(epio, MUSB_TXCSR); 130 if (!(csr & (MUSB_CSR0_TXPKTRDY | MUSB_CSR0_RXPKTRDY))) 131 break; 132 musb_writew(epio, MUSB_TXCSR, MUSB_CSR0_FLUSHFIFO); 133 csr = musb_readw(epio, MUSB_TXCSR); 134 udelay(10); 135 } while (--retries); 136 137 WARN(!retries, "Could not flush host TX%d fifo: csr: %04x\n", 138 ep->epnum, csr); 139 140 /* and reset for the next transfer */ 141 musb_writew(epio, MUSB_TXCSR, 0); 142 } 143 144 /* 145 * Start transmit. Caller is responsible for locking shared resources. 146 * musb must be locked. 147 */ 148 static inline void musb_h_tx_start(struct musb_hw_ep *ep) 149 { 150 u16 txcsr; 151 152 /* NOTE: no locks here; caller should lock and select EP */ 153 if (ep->epnum) { 154 txcsr = musb_readw(ep->regs, MUSB_TXCSR); 155 txcsr |= MUSB_TXCSR_TXPKTRDY | MUSB_TXCSR_H_WZC_BITS; 156 musb_writew(ep->regs, MUSB_TXCSR, txcsr); 157 } else { 158 txcsr = MUSB_CSR0_H_SETUPPKT | MUSB_CSR0_TXPKTRDY; 159 musb_writew(ep->regs, MUSB_CSR0, txcsr); 160 } 161 162 } 163 164 static inline void musb_h_tx_dma_start(struct musb_hw_ep *ep) 165 { 166 u16 txcsr; 167 168 /* NOTE: no locks here; caller should lock and select EP */ 169 txcsr = musb_readw(ep->regs, MUSB_TXCSR); 170 txcsr |= MUSB_TXCSR_DMAENAB | MUSB_TXCSR_H_WZC_BITS; 171 if (is_cppi_enabled(ep->musb)) 172 txcsr |= MUSB_TXCSR_DMAMODE; 173 musb_writew(ep->regs, MUSB_TXCSR, txcsr); 174 } 175 176 static void musb_ep_set_qh(struct musb_hw_ep *ep, int is_in, struct musb_qh *qh) 177 { 178 if (is_in != 0 || ep->is_shared_fifo) 179 ep->in_qh = qh; 180 if (is_in == 0 || ep->is_shared_fifo) 181 ep->out_qh = qh; 182 } 183 184 static struct musb_qh *musb_ep_get_qh(struct musb_hw_ep *ep, int is_in) 185 { 186 return is_in ? ep->in_qh : ep->out_qh; 187 } 188 189 /* 190 * Start the URB at the front of an endpoint's queue 191 * end must be claimed from the caller. 192 * 193 * Context: controller locked, irqs blocked 194 */ 195 static void 196 musb_start_urb(struct musb *musb, int is_in, struct musb_qh *qh) 197 { 198 u32 len; 199 void __iomem *mbase = musb->mregs; 200 struct urb *urb = next_urb(qh); 201 void *buf = urb->transfer_buffer; 202 u32 offset = 0; 203 struct musb_hw_ep *hw_ep = qh->hw_ep; 204 int epnum = hw_ep->epnum; 205 206 /* initialize software qh state */ 207 qh->offset = 0; 208 qh->segsize = 0; 209 210 /* gather right source of data */ 211 switch (qh->type) { 212 case USB_ENDPOINT_XFER_CONTROL: 213 /* control transfers always start with SETUP */ 214 is_in = 0; 215 musb->ep0_stage = MUSB_EP0_START; 216 buf = urb->setup_packet; 217 len = 8; 218 break; 219 case USB_ENDPOINT_XFER_ISOC: 220 qh->iso_idx = 0; 221 qh->frame = 0; 222 offset = urb->iso_frame_desc[0].offset; 223 len = urb->iso_frame_desc[0].length; 224 break; 225 default: /* bulk, interrupt */ 226 /* actual_length may be nonzero on retry paths */ 227 buf = urb->transfer_buffer + urb->actual_length; 228 len = urb->transfer_buffer_length - urb->actual_length; 229 } 230 231 trace_musb_urb_start(musb, urb); 232 233 /* Configure endpoint */ 234 musb_ep_set_qh(hw_ep, is_in, qh); 235 musb_ep_program(musb, epnum, urb, !is_in, buf, offset, len); 236 237 /* transmit may have more work: start it when it is time */ 238 if (is_in) 239 return; 240 241 /* determine if the time is right for a periodic transfer */ 242 switch (qh->type) { 243 case USB_ENDPOINT_XFER_ISOC: 244 case USB_ENDPOINT_XFER_INT: 245 musb_dbg(musb, "check whether there's still time for periodic Tx"); 246 /* FIXME this doesn't implement that scheduling policy ... 247 * or handle framecounter wrapping 248 */ 249 if (1) { /* Always assume URB_ISO_ASAP */ 250 /* REVISIT the SOF irq handler shouldn't duplicate 251 * this code; and we don't init urb->start_frame... 252 */ 253 qh->frame = 0; 254 goto start; 255 } else { 256 qh->frame = urb->start_frame; 257 /* enable SOF interrupt so we can count down */ 258 musb_dbg(musb, "SOF for %d", epnum); 259 #if 1 /* ifndef CONFIG_ARCH_DAVINCI */ 260 musb_writeb(mbase, MUSB_INTRUSBE, 0xff); 261 #endif 262 } 263 break; 264 default: 265 start: 266 musb_dbg(musb, "Start TX%d %s", epnum, 267 hw_ep->tx_channel ? "dma" : "pio"); 268 269 if (!hw_ep->tx_channel) 270 musb_h_tx_start(hw_ep); 271 else if (is_cppi_enabled(musb) || tusb_dma_omap(musb)) 272 musb_h_tx_dma_start(hw_ep); 273 } 274 } 275 276 /* Context: caller owns controller lock, IRQs are blocked */ 277 static void musb_giveback(struct musb *musb, struct urb *urb, int status) 278 __releases(musb->lock) 279 __acquires(musb->lock) 280 { 281 trace_musb_urb_gb(musb, urb); 282 283 usb_hcd_unlink_urb_from_ep(musb->hcd, urb); 284 spin_unlock(&musb->lock); 285 usb_hcd_giveback_urb(musb->hcd, urb, status); 286 spin_lock(&musb->lock); 287 } 288 289 /* 290 * Advance this hardware endpoint's queue, completing the specified URB and 291 * advancing to either the next URB queued to that qh, or else invalidating 292 * that qh and advancing to the next qh scheduled after the current one. 293 * 294 * Context: caller owns controller lock, IRQs are blocked 295 */ 296 static void musb_advance_schedule(struct musb *musb, struct urb *urb, 297 struct musb_hw_ep *hw_ep, int is_in) 298 { 299 struct musb_qh *qh = musb_ep_get_qh(hw_ep, is_in); 300 struct musb_hw_ep *ep = qh->hw_ep; 301 int ready = qh->is_ready; 302 int status; 303 u16 toggle; 304 305 status = (urb->status == -EINPROGRESS) ? 0 : urb->status; 306 307 /* save toggle eagerly, for paranoia */ 308 switch (qh->type) { 309 case USB_ENDPOINT_XFER_BULK: 310 case USB_ENDPOINT_XFER_INT: 311 toggle = musb->io.get_toggle(qh, !is_in); 312 usb_settoggle(urb->dev, qh->epnum, !is_in, toggle ? 1 : 0); 313 break; 314 case USB_ENDPOINT_XFER_ISOC: 315 if (status == 0 && urb->error_count) 316 status = -EXDEV; 317 break; 318 } 319 320 qh->is_ready = 0; 321 musb_giveback(musb, urb, status); 322 qh->is_ready = ready; 323 324 /* reclaim resources (and bandwidth) ASAP; deschedule it, and 325 * invalidate qh as soon as list_empty(&hep->urb_list) 326 */ 327 if (list_empty(&qh->hep->urb_list)) { 328 struct list_head *head; 329 struct dma_controller *dma = musb->dma_controller; 330 331 if (is_in) { 332 ep->rx_reinit = 1; 333 if (ep->rx_channel) { 334 dma->channel_release(ep->rx_channel); 335 ep->rx_channel = NULL; 336 } 337 } else { 338 ep->tx_reinit = 1; 339 if (ep->tx_channel) { 340 dma->channel_release(ep->tx_channel); 341 ep->tx_channel = NULL; 342 } 343 } 344 345 /* Clobber old pointers to this qh */ 346 musb_ep_set_qh(ep, is_in, NULL); 347 qh->hep->hcpriv = NULL; 348 349 switch (qh->type) { 350 351 case USB_ENDPOINT_XFER_CONTROL: 352 case USB_ENDPOINT_XFER_BULK: 353 /* fifo policy for these lists, except that NAKing 354 * should rotate a qh to the end (for fairness). 355 */ 356 if (qh->mux == 1) { 357 head = qh->ring.prev; 358 list_del(&qh->ring); 359 kfree(qh); 360 qh = first_qh(head); 361 break; 362 } 363 fallthrough; 364 365 case USB_ENDPOINT_XFER_ISOC: 366 case USB_ENDPOINT_XFER_INT: 367 /* this is where periodic bandwidth should be 368 * de-allocated if it's tracked and allocated; 369 * and where we'd update the schedule tree... 370 */ 371 kfree(qh); 372 qh = NULL; 373 break; 374 } 375 } 376 377 if (qh != NULL && qh->is_ready) { 378 musb_dbg(musb, "... next ep%d %cX urb %p", 379 hw_ep->epnum, is_in ? 'R' : 'T', next_urb(qh)); 380 musb_start_urb(musb, is_in, qh); 381 } 382 } 383 384 static u16 musb_h_flush_rxfifo(struct musb_hw_ep *hw_ep, u16 csr) 385 { 386 /* we don't want fifo to fill itself again; 387 * ignore dma (various models), 388 * leave toggle alone (may not have been saved yet) 389 */ 390 csr |= MUSB_RXCSR_FLUSHFIFO | MUSB_RXCSR_RXPKTRDY; 391 csr &= ~(MUSB_RXCSR_H_REQPKT 392 | MUSB_RXCSR_H_AUTOREQ 393 | MUSB_RXCSR_AUTOCLEAR); 394 395 /* write 2x to allow double buffering */ 396 musb_writew(hw_ep->regs, MUSB_RXCSR, csr); 397 musb_writew(hw_ep->regs, MUSB_RXCSR, csr); 398 399 /* flush writebuffer */ 400 return musb_readw(hw_ep->regs, MUSB_RXCSR); 401 } 402 403 /* 404 * PIO RX for a packet (or part of it). 405 */ 406 static bool 407 musb_host_packet_rx(struct musb *musb, struct urb *urb, u8 epnum, u8 iso_err) 408 { 409 u16 rx_count; 410 u8 *buf; 411 u16 csr; 412 bool done = false; 413 u32 length; 414 int do_flush = 0; 415 struct musb_hw_ep *hw_ep = musb->endpoints + epnum; 416 void __iomem *epio = hw_ep->regs; 417 struct musb_qh *qh = hw_ep->in_qh; 418 int pipe = urb->pipe; 419 void *buffer = urb->transfer_buffer; 420 421 /* musb_ep_select(mbase, epnum); */ 422 rx_count = musb_readw(epio, MUSB_RXCOUNT); 423 musb_dbg(musb, "RX%d count %d, buffer %p len %d/%d", epnum, rx_count, 424 urb->transfer_buffer, qh->offset, 425 urb->transfer_buffer_length); 426 427 /* unload FIFO */ 428 if (usb_pipeisoc(pipe)) { 429 int status = 0; 430 struct usb_iso_packet_descriptor *d; 431 432 if (iso_err) { 433 status = -EILSEQ; 434 urb->error_count++; 435 } 436 437 d = urb->iso_frame_desc + qh->iso_idx; 438 buf = buffer + d->offset; 439 length = d->length; 440 if (rx_count > length) { 441 if (status == 0) { 442 status = -EOVERFLOW; 443 urb->error_count++; 444 } 445 musb_dbg(musb, "OVERFLOW %d into %d", rx_count, length); 446 do_flush = 1; 447 } else 448 length = rx_count; 449 urb->actual_length += length; 450 d->actual_length = length; 451 452 d->status = status; 453 454 /* see if we are done */ 455 done = (++qh->iso_idx >= urb->number_of_packets); 456 } else { 457 /* non-isoch */ 458 buf = buffer + qh->offset; 459 length = urb->transfer_buffer_length - qh->offset; 460 if (rx_count > length) { 461 if (urb->status == -EINPROGRESS) 462 urb->status = -EOVERFLOW; 463 musb_dbg(musb, "OVERFLOW %d into %d", rx_count, length); 464 do_flush = 1; 465 } else 466 length = rx_count; 467 urb->actual_length += length; 468 qh->offset += length; 469 470 /* see if we are done */ 471 done = (urb->actual_length == urb->transfer_buffer_length) 472 || (rx_count < qh->maxpacket) 473 || (urb->status != -EINPROGRESS); 474 if (done 475 && (urb->status == -EINPROGRESS) 476 && (urb->transfer_flags & URB_SHORT_NOT_OK) 477 && (urb->actual_length 478 < urb->transfer_buffer_length)) 479 urb->status = -EREMOTEIO; 480 } 481 482 musb_read_fifo(hw_ep, length, buf); 483 484 csr = musb_readw(epio, MUSB_RXCSR); 485 csr |= MUSB_RXCSR_H_WZC_BITS; 486 if (unlikely(do_flush)) 487 musb_h_flush_rxfifo(hw_ep, csr); 488 else { 489 /* REVISIT this assumes AUTOCLEAR is never set */ 490 csr &= ~(MUSB_RXCSR_RXPKTRDY | MUSB_RXCSR_H_REQPKT); 491 if (!done) 492 csr |= MUSB_RXCSR_H_REQPKT; 493 musb_writew(epio, MUSB_RXCSR, csr); 494 } 495 496 return done; 497 } 498 499 /* we don't always need to reinit a given side of an endpoint... 500 * when we do, use tx/rx reinit routine and then construct a new CSR 501 * to address data toggle, NYET, and DMA or PIO. 502 * 503 * it's possible that driver bugs (especially for DMA) or aborting a 504 * transfer might have left the endpoint busier than it should be. 505 * the busy/not-empty tests are basically paranoia. 506 */ 507 static void 508 musb_rx_reinit(struct musb *musb, struct musb_qh *qh, u8 epnum) 509 { 510 struct musb_hw_ep *ep = musb->endpoints + epnum; 511 u16 csr; 512 513 /* NOTE: we know the "rx" fifo reinit never triggers for ep0. 514 * That always uses tx_reinit since ep0 repurposes TX register 515 * offsets; the initial SETUP packet is also a kind of OUT. 516 */ 517 518 /* if programmed for Tx, put it in RX mode */ 519 if (ep->is_shared_fifo) { 520 csr = musb_readw(ep->regs, MUSB_TXCSR); 521 if (csr & MUSB_TXCSR_MODE) { 522 musb_h_tx_flush_fifo(ep); 523 csr = musb_readw(ep->regs, MUSB_TXCSR); 524 musb_writew(ep->regs, MUSB_TXCSR, 525 csr | MUSB_TXCSR_FRCDATATOG); 526 } 527 528 /* 529 * Clear the MODE bit (and everything else) to enable Rx. 530 * NOTE: we mustn't clear the DMAMODE bit before DMAENAB. 531 */ 532 if (csr & MUSB_TXCSR_DMAMODE) 533 musb_writew(ep->regs, MUSB_TXCSR, MUSB_TXCSR_DMAMODE); 534 musb_writew(ep->regs, MUSB_TXCSR, 0); 535 536 /* scrub all previous state, clearing toggle */ 537 } 538 csr = musb_readw(ep->regs, MUSB_RXCSR); 539 if (csr & MUSB_RXCSR_RXPKTRDY) 540 WARNING("rx%d, packet/%d ready?\n", ep->epnum, 541 musb_readw(ep->regs, MUSB_RXCOUNT)); 542 543 musb_h_flush_rxfifo(ep, MUSB_RXCSR_CLRDATATOG); 544 545 /* target addr and (for multipoint) hub addr/port */ 546 if (musb->is_multipoint) { 547 musb_write_rxfunaddr(musb, epnum, qh->addr_reg); 548 musb_write_rxhubaddr(musb, epnum, qh->h_addr_reg); 549 musb_write_rxhubport(musb, epnum, qh->h_port_reg); 550 } else 551 musb_writeb(musb->mregs, MUSB_FADDR, qh->addr_reg); 552 553 /* protocol/endpoint, interval/NAKlimit, i/o size */ 554 musb_writeb(ep->regs, MUSB_RXTYPE, qh->type_reg); 555 musb_writeb(ep->regs, MUSB_RXINTERVAL, qh->intv_reg); 556 /* NOTE: bulk combining rewrites high bits of maxpacket */ 557 /* Set RXMAXP with the FIFO size of the endpoint 558 * to disable double buffer mode. 559 */ 560 musb_writew(ep->regs, MUSB_RXMAXP, 561 qh->maxpacket | ((qh->hb_mult - 1) << 11)); 562 563 ep->rx_reinit = 0; 564 } 565 566 static void musb_tx_dma_set_mode_mentor(struct musb_hw_ep *hw_ep, 567 struct musb_qh *qh, 568 u32 *length, u8 *mode) 569 { 570 struct dma_channel *channel = hw_ep->tx_channel; 571 void __iomem *epio = hw_ep->regs; 572 u16 pkt_size = qh->maxpacket; 573 u16 csr; 574 575 if (*length > channel->max_len) 576 *length = channel->max_len; 577 578 csr = musb_readw(epio, MUSB_TXCSR); 579 if (*length > pkt_size) { 580 *mode = 1; 581 csr |= MUSB_TXCSR_DMAMODE | MUSB_TXCSR_DMAENAB; 582 /* autoset shouldn't be set in high bandwidth */ 583 /* 584 * Enable Autoset according to table 585 * below 586 * bulk_split hb_mult Autoset_Enable 587 * 0 1 Yes(Normal) 588 * 0 >1 No(High BW ISO) 589 * 1 1 Yes(HS bulk) 590 * 1 >1 Yes(FS bulk) 591 */ 592 if (qh->hb_mult == 1 || (qh->hb_mult > 1 && 593 can_bulk_split(hw_ep->musb, qh->type))) 594 csr |= MUSB_TXCSR_AUTOSET; 595 } else { 596 *mode = 0; 597 csr &= ~(MUSB_TXCSR_AUTOSET | MUSB_TXCSR_DMAMODE); 598 csr |= MUSB_TXCSR_DMAENAB; /* against programmer's guide */ 599 } 600 channel->desired_mode = *mode; 601 musb_writew(epio, MUSB_TXCSR, csr); 602 } 603 604 static void musb_tx_dma_set_mode_cppi_tusb(struct musb_hw_ep *hw_ep, 605 struct urb *urb, 606 u8 *mode) 607 { 608 struct dma_channel *channel = hw_ep->tx_channel; 609 610 channel->actual_len = 0; 611 612 /* 613 * TX uses "RNDIS" mode automatically but needs help 614 * to identify the zero-length-final-packet case. 615 */ 616 *mode = (urb->transfer_flags & URB_ZERO_PACKET) ? 1 : 0; 617 } 618 619 static bool musb_tx_dma_program(struct dma_controller *dma, 620 struct musb_hw_ep *hw_ep, struct musb_qh *qh, 621 struct urb *urb, u32 offset, u32 length) 622 { 623 struct dma_channel *channel = hw_ep->tx_channel; 624 u16 pkt_size = qh->maxpacket; 625 u8 mode; 626 627 if (musb_dma_inventra(hw_ep->musb) || musb_dma_ux500(hw_ep->musb)) 628 musb_tx_dma_set_mode_mentor(hw_ep, qh, 629 &length, &mode); 630 else if (is_cppi_enabled(hw_ep->musb) || tusb_dma_omap(hw_ep->musb)) 631 musb_tx_dma_set_mode_cppi_tusb(hw_ep, urb, &mode); 632 else 633 return false; 634 635 qh->segsize = length; 636 637 /* 638 * Ensure the data reaches to main memory before starting 639 * DMA transfer 640 */ 641 wmb(); 642 643 if (!dma->channel_program(channel, pkt_size, mode, 644 urb->transfer_dma + offset, length)) { 645 void __iomem *epio = hw_ep->regs; 646 u16 csr; 647 648 dma->channel_release(channel); 649 hw_ep->tx_channel = NULL; 650 651 csr = musb_readw(epio, MUSB_TXCSR); 652 csr &= ~(MUSB_TXCSR_AUTOSET | MUSB_TXCSR_DMAENAB); 653 musb_writew(epio, MUSB_TXCSR, csr | MUSB_TXCSR_H_WZC_BITS); 654 return false; 655 } 656 return true; 657 } 658 659 /* 660 * Program an HDRC endpoint as per the given URB 661 * Context: irqs blocked, controller lock held 662 */ 663 static void musb_ep_program(struct musb *musb, u8 epnum, 664 struct urb *urb, int is_out, 665 u8 *buf, u32 offset, u32 len) 666 { 667 struct dma_controller *dma_controller; 668 struct dma_channel *dma_channel; 669 u8 dma_ok; 670 void __iomem *mbase = musb->mregs; 671 struct musb_hw_ep *hw_ep = musb->endpoints + epnum; 672 void __iomem *epio = hw_ep->regs; 673 struct musb_qh *qh = musb_ep_get_qh(hw_ep, !is_out); 674 u16 packet_sz = qh->maxpacket; 675 u8 use_dma = 1; 676 u16 csr; 677 678 musb_dbg(musb, "%s hw%d urb %p spd%d dev%d ep%d%s " 679 "h_addr%02x h_port%02x bytes %d", 680 is_out ? "-->" : "<--", 681 epnum, urb, urb->dev->speed, 682 qh->addr_reg, qh->epnum, is_out ? "out" : "in", 683 qh->h_addr_reg, qh->h_port_reg, 684 len); 685 686 musb_ep_select(mbase, epnum); 687 688 if (is_out && !len) { 689 use_dma = 0; 690 csr = musb_readw(epio, MUSB_TXCSR); 691 csr &= ~MUSB_TXCSR_DMAENAB; 692 musb_writew(epio, MUSB_TXCSR, csr); 693 hw_ep->tx_channel = NULL; 694 } 695 696 /* candidate for DMA? */ 697 dma_controller = musb->dma_controller; 698 if (use_dma && is_dma_capable() && epnum && dma_controller) { 699 dma_channel = is_out ? hw_ep->tx_channel : hw_ep->rx_channel; 700 if (!dma_channel) { 701 dma_channel = dma_controller->channel_alloc( 702 dma_controller, hw_ep, is_out); 703 if (is_out) 704 hw_ep->tx_channel = dma_channel; 705 else 706 hw_ep->rx_channel = dma_channel; 707 } 708 } else 709 dma_channel = NULL; 710 711 /* make sure we clear DMAEnab, autoSet bits from previous run */ 712 713 /* OUT/transmit/EP0 or IN/receive? */ 714 if (is_out) { 715 u16 csr; 716 u16 int_txe; 717 u16 load_count; 718 719 csr = musb_readw(epio, MUSB_TXCSR); 720 721 /* disable interrupt in case we flush */ 722 int_txe = musb->intrtxe; 723 musb_writew(mbase, MUSB_INTRTXE, int_txe & ~(1 << epnum)); 724 725 /* general endpoint setup */ 726 if (epnum) { 727 /* flush all old state, set default */ 728 /* 729 * We could be flushing valid 730 * packets in double buffering 731 * case 732 */ 733 if (!hw_ep->tx_double_buffered) 734 musb_h_tx_flush_fifo(hw_ep); 735 736 /* 737 * We must not clear the DMAMODE bit before or in 738 * the same cycle with the DMAENAB bit, so we clear 739 * the latter first... 740 */ 741 csr &= ~(MUSB_TXCSR_H_NAKTIMEOUT 742 | MUSB_TXCSR_AUTOSET 743 | MUSB_TXCSR_DMAENAB 744 | MUSB_TXCSR_FRCDATATOG 745 | MUSB_TXCSR_H_RXSTALL 746 | MUSB_TXCSR_H_ERROR 747 | MUSB_TXCSR_TXPKTRDY 748 ); 749 csr |= MUSB_TXCSR_MODE; 750 751 if (!hw_ep->tx_double_buffered) 752 csr |= musb->io.set_toggle(qh, is_out, urb); 753 754 musb_writew(epio, MUSB_TXCSR, csr); 755 /* REVISIT may need to clear FLUSHFIFO ... */ 756 csr &= ~MUSB_TXCSR_DMAMODE; 757 musb_writew(epio, MUSB_TXCSR, csr); 758 csr = musb_readw(epio, MUSB_TXCSR); 759 } else { 760 /* endpoint 0: just flush */ 761 musb_h_ep0_flush_fifo(hw_ep); 762 } 763 764 /* target addr and (for multipoint) hub addr/port */ 765 if (musb->is_multipoint) { 766 musb_write_txfunaddr(musb, epnum, qh->addr_reg); 767 musb_write_txhubaddr(musb, epnum, qh->h_addr_reg); 768 musb_write_txhubport(musb, epnum, qh->h_port_reg); 769 /* FIXME if !epnum, do the same for RX ... */ 770 } else 771 musb_writeb(mbase, MUSB_FADDR, qh->addr_reg); 772 773 /* protocol/endpoint/interval/NAKlimit */ 774 if (epnum) { 775 musb_writeb(epio, MUSB_TXTYPE, qh->type_reg); 776 if (can_bulk_split(musb, qh->type)) { 777 qh->hb_mult = hw_ep->max_packet_sz_tx 778 / packet_sz; 779 musb_writew(epio, MUSB_TXMAXP, packet_sz 780 | ((qh->hb_mult) - 1) << 11); 781 } else { 782 musb_writew(epio, MUSB_TXMAXP, 783 qh->maxpacket | 784 ((qh->hb_mult - 1) << 11)); 785 } 786 musb_writeb(epio, MUSB_TXINTERVAL, qh->intv_reg); 787 } else { 788 musb_writeb(epio, MUSB_NAKLIMIT0, qh->intv_reg); 789 if (musb->is_multipoint) 790 musb_writeb(epio, MUSB_TYPE0, 791 qh->type_reg); 792 } 793 794 if (can_bulk_split(musb, qh->type)) 795 load_count = min((u32) hw_ep->max_packet_sz_tx, 796 len); 797 else 798 load_count = min((u32) packet_sz, len); 799 800 if (dma_channel && musb_tx_dma_program(dma_controller, 801 hw_ep, qh, urb, offset, len)) 802 load_count = 0; 803 804 if (load_count) { 805 /* PIO to load FIFO */ 806 qh->segsize = load_count; 807 if (!buf) { 808 sg_miter_start(&qh->sg_miter, urb->sg, 1, 809 SG_MITER_ATOMIC 810 | SG_MITER_FROM_SG); 811 if (!sg_miter_next(&qh->sg_miter)) { 812 dev_err(musb->controller, 813 "error: sg" 814 "list empty\n"); 815 sg_miter_stop(&qh->sg_miter); 816 goto finish; 817 } 818 buf = qh->sg_miter.addr + urb->sg->offset + 819 urb->actual_length; 820 load_count = min_t(u32, load_count, 821 qh->sg_miter.length); 822 musb_write_fifo(hw_ep, load_count, buf); 823 qh->sg_miter.consumed = load_count; 824 sg_miter_stop(&qh->sg_miter); 825 } else 826 musb_write_fifo(hw_ep, load_count, buf); 827 } 828 finish: 829 /* re-enable interrupt */ 830 musb_writew(mbase, MUSB_INTRTXE, int_txe); 831 832 /* IN/receive */ 833 } else { 834 u16 csr = 0; 835 836 if (hw_ep->rx_reinit) { 837 musb_rx_reinit(musb, qh, epnum); 838 csr |= musb->io.set_toggle(qh, is_out, urb); 839 840 if (qh->type == USB_ENDPOINT_XFER_INT) 841 csr |= MUSB_RXCSR_DISNYET; 842 843 } else { 844 csr = musb_readw(hw_ep->regs, MUSB_RXCSR); 845 846 if (csr & (MUSB_RXCSR_RXPKTRDY 847 | MUSB_RXCSR_DMAENAB 848 | MUSB_RXCSR_H_REQPKT)) 849 ERR("broken !rx_reinit, ep%d csr %04x\n", 850 hw_ep->epnum, csr); 851 852 /* scrub any stale state, leaving toggle alone */ 853 csr &= MUSB_RXCSR_DISNYET; 854 } 855 856 /* kick things off */ 857 858 if ((is_cppi_enabled(musb) || tusb_dma_omap(musb)) && dma_channel) { 859 /* Candidate for DMA */ 860 dma_channel->actual_len = 0L; 861 qh->segsize = len; 862 863 /* AUTOREQ is in a DMA register */ 864 musb_writew(hw_ep->regs, MUSB_RXCSR, csr); 865 csr = musb_readw(hw_ep->regs, MUSB_RXCSR); 866 867 /* 868 * Unless caller treats short RX transfers as 869 * errors, we dare not queue multiple transfers. 870 */ 871 dma_ok = dma_controller->channel_program(dma_channel, 872 packet_sz, !(urb->transfer_flags & 873 URB_SHORT_NOT_OK), 874 urb->transfer_dma + offset, 875 qh->segsize); 876 if (!dma_ok) { 877 dma_controller->channel_release(dma_channel); 878 hw_ep->rx_channel = dma_channel = NULL; 879 } else 880 csr |= MUSB_RXCSR_DMAENAB; 881 } 882 883 csr |= MUSB_RXCSR_H_REQPKT; 884 musb_dbg(musb, "RXCSR%d := %04x", epnum, csr); 885 musb_writew(hw_ep->regs, MUSB_RXCSR, csr); 886 csr = musb_readw(hw_ep->regs, MUSB_RXCSR); 887 } 888 } 889 890 /* Schedule next QH from musb->in_bulk/out_bulk and move the current qh to 891 * the end; avoids starvation for other endpoints. 892 */ 893 static void musb_bulk_nak_timeout(struct musb *musb, struct musb_hw_ep *ep, 894 int is_in) 895 { 896 struct dma_channel *dma; 897 struct urb *urb; 898 void __iomem *mbase = musb->mregs; 899 void __iomem *epio = ep->regs; 900 struct musb_qh *cur_qh, *next_qh; 901 u16 rx_csr, tx_csr; 902 u16 toggle; 903 904 musb_ep_select(mbase, ep->epnum); 905 if (is_in) { 906 dma = is_dma_capable() ? ep->rx_channel : NULL; 907 908 /* 909 * Need to stop the transaction by clearing REQPKT first 910 * then the NAK Timeout bit ref MUSBMHDRC USB 2.0 HIGH-SPEED 911 * DUAL-ROLE CONTROLLER Programmer's Guide, section 9.2.2 912 */ 913 rx_csr = musb_readw(epio, MUSB_RXCSR); 914 rx_csr |= MUSB_RXCSR_H_WZC_BITS; 915 rx_csr &= ~MUSB_RXCSR_H_REQPKT; 916 musb_writew(epio, MUSB_RXCSR, rx_csr); 917 rx_csr &= ~MUSB_RXCSR_DATAERROR; 918 musb_writew(epio, MUSB_RXCSR, rx_csr); 919 920 cur_qh = first_qh(&musb->in_bulk); 921 } else { 922 dma = is_dma_capable() ? ep->tx_channel : NULL; 923 924 /* clear nak timeout bit */ 925 tx_csr = musb_readw(epio, MUSB_TXCSR); 926 tx_csr |= MUSB_TXCSR_H_WZC_BITS; 927 tx_csr &= ~MUSB_TXCSR_H_NAKTIMEOUT; 928 musb_writew(epio, MUSB_TXCSR, tx_csr); 929 930 cur_qh = first_qh(&musb->out_bulk); 931 } 932 if (cur_qh) { 933 urb = next_urb(cur_qh); 934 if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { 935 dma->status = MUSB_DMA_STATUS_CORE_ABORT; 936 musb->dma_controller->channel_abort(dma); 937 urb->actual_length += dma->actual_len; 938 dma->actual_len = 0L; 939 } 940 toggle = musb->io.get_toggle(cur_qh, !is_in); 941 usb_settoggle(urb->dev, cur_qh->epnum, !is_in, toggle ? 1 : 0); 942 943 if (is_in) { 944 /* move cur_qh to end of queue */ 945 list_move_tail(&cur_qh->ring, &musb->in_bulk); 946 947 /* get the next qh from musb->in_bulk */ 948 next_qh = first_qh(&musb->in_bulk); 949 950 /* set rx_reinit and schedule the next qh */ 951 ep->rx_reinit = 1; 952 } else { 953 /* move cur_qh to end of queue */ 954 list_move_tail(&cur_qh->ring, &musb->out_bulk); 955 956 /* get the next qh from musb->out_bulk */ 957 next_qh = first_qh(&musb->out_bulk); 958 959 /* set tx_reinit and schedule the next qh */ 960 ep->tx_reinit = 1; 961 } 962 963 if (next_qh) 964 musb_start_urb(musb, is_in, next_qh); 965 } 966 } 967 968 /* 969 * Service the default endpoint (ep0) as host. 970 * Return true until it's time to start the status stage. 971 */ 972 static bool musb_h_ep0_continue(struct musb *musb, u16 len, struct urb *urb) 973 { 974 bool more = false; 975 u8 *fifo_dest = NULL; 976 u16 fifo_count = 0; 977 struct musb_hw_ep *hw_ep = musb->control_ep; 978 struct musb_qh *qh = hw_ep->in_qh; 979 struct usb_ctrlrequest *request; 980 981 switch (musb->ep0_stage) { 982 case MUSB_EP0_IN: 983 fifo_dest = urb->transfer_buffer + urb->actual_length; 984 fifo_count = min_t(size_t, len, urb->transfer_buffer_length - 985 urb->actual_length); 986 if (fifo_count < len) 987 urb->status = -EOVERFLOW; 988 989 musb_read_fifo(hw_ep, fifo_count, fifo_dest); 990 991 urb->actual_length += fifo_count; 992 if (len < qh->maxpacket) { 993 /* always terminate on short read; it's 994 * rarely reported as an error. 995 */ 996 } else if (urb->actual_length < 997 urb->transfer_buffer_length) 998 more = true; 999 break; 1000 case MUSB_EP0_START: 1001 request = (struct usb_ctrlrequest *) urb->setup_packet; 1002 1003 if (!request->wLength) { 1004 musb_dbg(musb, "start no-DATA"); 1005 break; 1006 } else if (request->bRequestType & USB_DIR_IN) { 1007 musb_dbg(musb, "start IN-DATA"); 1008 musb->ep0_stage = MUSB_EP0_IN; 1009 more = true; 1010 break; 1011 } else { 1012 musb_dbg(musb, "start OUT-DATA"); 1013 musb->ep0_stage = MUSB_EP0_OUT; 1014 more = true; 1015 } 1016 fallthrough; 1017 case MUSB_EP0_OUT: 1018 fifo_count = min_t(size_t, qh->maxpacket, 1019 urb->transfer_buffer_length - 1020 urb->actual_length); 1021 if (fifo_count) { 1022 fifo_dest = (u8 *) (urb->transfer_buffer 1023 + urb->actual_length); 1024 musb_dbg(musb, "Sending %d byte%s to ep0 fifo %p", 1025 fifo_count, 1026 (fifo_count == 1) ? "" : "s", 1027 fifo_dest); 1028 musb_write_fifo(hw_ep, fifo_count, fifo_dest); 1029 1030 urb->actual_length += fifo_count; 1031 more = true; 1032 } 1033 break; 1034 default: 1035 ERR("bogus ep0 stage %d\n", musb->ep0_stage); 1036 break; 1037 } 1038 1039 return more; 1040 } 1041 1042 /* 1043 * Handle default endpoint interrupt as host. Only called in IRQ time 1044 * from musb_interrupt(). 1045 * 1046 * called with controller irqlocked 1047 */ 1048 irqreturn_t musb_h_ep0_irq(struct musb *musb) 1049 { 1050 struct urb *urb; 1051 u16 csr, len; 1052 int status = 0; 1053 void __iomem *mbase = musb->mregs; 1054 struct musb_hw_ep *hw_ep = musb->control_ep; 1055 void __iomem *epio = hw_ep->regs; 1056 struct musb_qh *qh = hw_ep->in_qh; 1057 bool complete = false; 1058 irqreturn_t retval = IRQ_NONE; 1059 1060 /* ep0 only has one queue, "in" */ 1061 urb = next_urb(qh); 1062 1063 musb_ep_select(mbase, 0); 1064 csr = musb_readw(epio, MUSB_CSR0); 1065 len = (csr & MUSB_CSR0_RXPKTRDY) 1066 ? musb_readb(epio, MUSB_COUNT0) 1067 : 0; 1068 1069 musb_dbg(musb, "<== csr0 %04x, qh %p, count %d, urb %p, stage %d", 1070 csr, qh, len, urb, musb->ep0_stage); 1071 1072 /* if we just did status stage, we are done */ 1073 if (MUSB_EP0_STATUS == musb->ep0_stage) { 1074 retval = IRQ_HANDLED; 1075 complete = true; 1076 } 1077 1078 /* prepare status */ 1079 if (csr & MUSB_CSR0_H_RXSTALL) { 1080 musb_dbg(musb, "STALLING ENDPOINT"); 1081 status = -EPIPE; 1082 1083 } else if (csr & MUSB_CSR0_H_ERROR) { 1084 musb_dbg(musb, "no response, csr0 %04x", csr); 1085 status = -EPROTO; 1086 1087 } else if (csr & MUSB_CSR0_H_NAKTIMEOUT) { 1088 musb_dbg(musb, "control NAK timeout"); 1089 1090 /* NOTE: this code path would be a good place to PAUSE a 1091 * control transfer, if another one is queued, so that 1092 * ep0 is more likely to stay busy. That's already done 1093 * for bulk RX transfers. 1094 * 1095 * if (qh->ring.next != &musb->control), then 1096 * we have a candidate... NAKing is *NOT* an error 1097 */ 1098 musb_writew(epio, MUSB_CSR0, 0); 1099 retval = IRQ_HANDLED; 1100 } 1101 1102 if (status) { 1103 musb_dbg(musb, "aborting"); 1104 retval = IRQ_HANDLED; 1105 if (urb) 1106 urb->status = status; 1107 complete = true; 1108 1109 /* use the proper sequence to abort the transfer */ 1110 if (csr & MUSB_CSR0_H_REQPKT) { 1111 csr &= ~MUSB_CSR0_H_REQPKT; 1112 musb_writew(epio, MUSB_CSR0, csr); 1113 csr &= ~MUSB_CSR0_H_NAKTIMEOUT; 1114 musb_writew(epio, MUSB_CSR0, csr); 1115 } else { 1116 musb_h_ep0_flush_fifo(hw_ep); 1117 } 1118 1119 musb_writeb(epio, MUSB_NAKLIMIT0, 0); 1120 1121 /* clear it */ 1122 musb_writew(epio, MUSB_CSR0, 0); 1123 } 1124 1125 if (unlikely(!urb)) { 1126 /* stop endpoint since we have no place for its data, this 1127 * SHOULD NEVER HAPPEN! */ 1128 ERR("no URB for end 0\n"); 1129 1130 musb_h_ep0_flush_fifo(hw_ep); 1131 goto done; 1132 } 1133 1134 if (!complete) { 1135 /* call common logic and prepare response */ 1136 if (musb_h_ep0_continue(musb, len, urb)) { 1137 /* more packets required */ 1138 csr = (MUSB_EP0_IN == musb->ep0_stage) 1139 ? MUSB_CSR0_H_REQPKT : MUSB_CSR0_TXPKTRDY; 1140 } else { 1141 /* data transfer complete; perform status phase */ 1142 if (usb_pipeout(urb->pipe) 1143 || !urb->transfer_buffer_length) 1144 csr = MUSB_CSR0_H_STATUSPKT 1145 | MUSB_CSR0_H_REQPKT; 1146 else 1147 csr = MUSB_CSR0_H_STATUSPKT 1148 | MUSB_CSR0_TXPKTRDY; 1149 1150 /* disable ping token in status phase */ 1151 csr |= MUSB_CSR0_H_DIS_PING; 1152 1153 /* flag status stage */ 1154 musb->ep0_stage = MUSB_EP0_STATUS; 1155 1156 musb_dbg(musb, "ep0 STATUS, csr %04x", csr); 1157 1158 } 1159 musb_writew(epio, MUSB_CSR0, csr); 1160 retval = IRQ_HANDLED; 1161 } else 1162 musb->ep0_stage = MUSB_EP0_IDLE; 1163 1164 /* call completion handler if done */ 1165 if (complete) 1166 musb_advance_schedule(musb, urb, hw_ep, 1); 1167 done: 1168 return retval; 1169 } 1170 1171 1172 #ifdef CONFIG_USB_INVENTRA_DMA 1173 1174 /* Host side TX (OUT) using Mentor DMA works as follows: 1175 submit_urb -> 1176 - if queue was empty, Program Endpoint 1177 - ... which starts DMA to fifo in mode 1 or 0 1178 1179 DMA Isr (transfer complete) -> TxAvail() 1180 - Stop DMA (~DmaEnab) (<--- Alert ... currently happens 1181 only in musb_cleanup_urb) 1182 - TxPktRdy has to be set in mode 0 or for 1183 short packets in mode 1. 1184 */ 1185 1186 #endif 1187 1188 /* Service a Tx-Available or dma completion irq for the endpoint */ 1189 void musb_host_tx(struct musb *musb, u8 epnum) 1190 { 1191 int pipe; 1192 bool done = false; 1193 u16 tx_csr; 1194 size_t length = 0; 1195 size_t offset = 0; 1196 struct musb_hw_ep *hw_ep = musb->endpoints + epnum; 1197 void __iomem *epio = hw_ep->regs; 1198 struct musb_qh *qh = hw_ep->out_qh; 1199 struct urb *urb = next_urb(qh); 1200 u32 status = 0; 1201 void __iomem *mbase = musb->mregs; 1202 struct dma_channel *dma; 1203 bool transfer_pending = false; 1204 1205 musb_ep_select(mbase, epnum); 1206 tx_csr = musb_readw(epio, MUSB_TXCSR); 1207 1208 /* with CPPI, DMA sometimes triggers "extra" irqs */ 1209 if (!urb) { 1210 musb_dbg(musb, "extra TX%d ready, csr %04x", epnum, tx_csr); 1211 return; 1212 } 1213 1214 pipe = urb->pipe; 1215 dma = is_dma_capable() ? hw_ep->tx_channel : NULL; 1216 trace_musb_urb_tx(musb, urb); 1217 musb_dbg(musb, "OUT/TX%d end, csr %04x%s", epnum, tx_csr, 1218 dma ? ", dma" : ""); 1219 1220 /* check for errors */ 1221 if (tx_csr & MUSB_TXCSR_H_RXSTALL) { 1222 /* dma was disabled, fifo flushed */ 1223 musb_dbg(musb, "TX end %d stall", epnum); 1224 1225 /* stall; record URB status */ 1226 status = -EPIPE; 1227 1228 } else if (tx_csr & MUSB_TXCSR_H_ERROR) { 1229 /* (NON-ISO) dma was disabled, fifo flushed */ 1230 musb_dbg(musb, "TX 3strikes on ep=%d", epnum); 1231 1232 status = -ETIMEDOUT; 1233 1234 } else if (tx_csr & MUSB_TXCSR_H_NAKTIMEOUT) { 1235 if (USB_ENDPOINT_XFER_BULK == qh->type && qh->mux == 1 1236 && !list_is_singular(&musb->out_bulk)) { 1237 musb_dbg(musb, "NAK timeout on TX%d ep", epnum); 1238 musb_bulk_nak_timeout(musb, hw_ep, 0); 1239 } else { 1240 musb_dbg(musb, "TX ep%d device not responding", epnum); 1241 /* NOTE: this code path would be a good place to PAUSE a 1242 * transfer, if there's some other (nonperiodic) tx urb 1243 * that could use this fifo. (dma complicates it...) 1244 * That's already done for bulk RX transfers. 1245 * 1246 * if (bulk && qh->ring.next != &musb->out_bulk), then 1247 * we have a candidate... NAKing is *NOT* an error 1248 */ 1249 musb_ep_select(mbase, epnum); 1250 musb_writew(epio, MUSB_TXCSR, 1251 MUSB_TXCSR_H_WZC_BITS 1252 | MUSB_TXCSR_TXPKTRDY); 1253 } 1254 return; 1255 } 1256 1257 done: 1258 if (status) { 1259 if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { 1260 dma->status = MUSB_DMA_STATUS_CORE_ABORT; 1261 musb->dma_controller->channel_abort(dma); 1262 } 1263 1264 /* do the proper sequence to abort the transfer in the 1265 * usb core; the dma engine should already be stopped. 1266 */ 1267 musb_h_tx_flush_fifo(hw_ep); 1268 tx_csr &= ~(MUSB_TXCSR_AUTOSET 1269 | MUSB_TXCSR_DMAENAB 1270 | MUSB_TXCSR_H_ERROR 1271 | MUSB_TXCSR_H_RXSTALL 1272 | MUSB_TXCSR_H_NAKTIMEOUT 1273 ); 1274 1275 musb_ep_select(mbase, epnum); 1276 musb_writew(epio, MUSB_TXCSR, tx_csr); 1277 /* REVISIT may need to clear FLUSHFIFO ... */ 1278 musb_writew(epio, MUSB_TXCSR, tx_csr); 1279 musb_writeb(epio, MUSB_TXINTERVAL, 0); 1280 1281 done = true; 1282 } 1283 1284 /* second cppi case */ 1285 if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { 1286 musb_dbg(musb, "extra TX%d ready, csr %04x", epnum, tx_csr); 1287 return; 1288 } 1289 1290 if (is_dma_capable() && dma && !status) { 1291 /* 1292 * DMA has completed. But if we're using DMA mode 1 (multi 1293 * packet DMA), we need a terminal TXPKTRDY interrupt before 1294 * we can consider this transfer completed, lest we trash 1295 * its last packet when writing the next URB's data. So we 1296 * switch back to mode 0 to get that interrupt; we'll come 1297 * back here once it happens. 1298 */ 1299 if (tx_csr & MUSB_TXCSR_DMAMODE) { 1300 /* 1301 * We shouldn't clear DMAMODE with DMAENAB set; so 1302 * clear them in a safe order. That should be OK 1303 * once TXPKTRDY has been set (and I've never seen 1304 * it being 0 at this moment -- DMA interrupt latency 1305 * is significant) but if it hasn't been then we have 1306 * no choice but to stop being polite and ignore the 1307 * programmer's guide... :-) 1308 * 1309 * Note that we must write TXCSR with TXPKTRDY cleared 1310 * in order not to re-trigger the packet send (this bit 1311 * can't be cleared by CPU), and there's another caveat: 1312 * TXPKTRDY may be set shortly and then cleared in the 1313 * double-buffered FIFO mode, so we do an extra TXCSR 1314 * read for debouncing... 1315 */ 1316 tx_csr &= musb_readw(epio, MUSB_TXCSR); 1317 if (tx_csr & MUSB_TXCSR_TXPKTRDY) { 1318 tx_csr &= ~(MUSB_TXCSR_DMAENAB | 1319 MUSB_TXCSR_TXPKTRDY); 1320 musb_writew(epio, MUSB_TXCSR, 1321 tx_csr | MUSB_TXCSR_H_WZC_BITS); 1322 } 1323 tx_csr &= ~(MUSB_TXCSR_DMAMODE | 1324 MUSB_TXCSR_TXPKTRDY); 1325 musb_writew(epio, MUSB_TXCSR, 1326 tx_csr | MUSB_TXCSR_H_WZC_BITS); 1327 1328 /* 1329 * There is no guarantee that we'll get an interrupt 1330 * after clearing DMAMODE as we might have done this 1331 * too late (after TXPKTRDY was cleared by controller). 1332 * Re-read TXCSR as we have spoiled its previous value. 1333 */ 1334 tx_csr = musb_readw(epio, MUSB_TXCSR); 1335 } 1336 1337 /* 1338 * We may get here from a DMA completion or TXPKTRDY interrupt. 1339 * In any case, we must check the FIFO status here and bail out 1340 * only if the FIFO still has data -- that should prevent the 1341 * "missed" TXPKTRDY interrupts and deal with double-buffered 1342 * FIFO mode too... 1343 */ 1344 if (tx_csr & (MUSB_TXCSR_FIFONOTEMPTY | MUSB_TXCSR_TXPKTRDY)) { 1345 musb_dbg(musb, 1346 "DMA complete but FIFO not empty, CSR %04x", 1347 tx_csr); 1348 return; 1349 } 1350 } 1351 1352 if (!status || dma || usb_pipeisoc(pipe)) { 1353 if (dma) 1354 length = dma->actual_len; 1355 else 1356 length = qh->segsize; 1357 qh->offset += length; 1358 1359 if (usb_pipeisoc(pipe)) { 1360 struct usb_iso_packet_descriptor *d; 1361 1362 d = urb->iso_frame_desc + qh->iso_idx; 1363 d->actual_length = length; 1364 d->status = status; 1365 if (++qh->iso_idx >= urb->number_of_packets) { 1366 done = true; 1367 } else { 1368 d++; 1369 offset = d->offset; 1370 length = d->length; 1371 } 1372 } else if (dma && urb->transfer_buffer_length == qh->offset) { 1373 done = true; 1374 } else { 1375 /* see if we need to send more data, or ZLP */ 1376 if (qh->segsize < qh->maxpacket) 1377 done = true; 1378 else if (qh->offset == urb->transfer_buffer_length 1379 && !(urb->transfer_flags 1380 & URB_ZERO_PACKET)) 1381 done = true; 1382 if (!done) { 1383 offset = qh->offset; 1384 length = urb->transfer_buffer_length - offset; 1385 transfer_pending = true; 1386 } 1387 } 1388 } 1389 1390 /* urb->status != -EINPROGRESS means request has been faulted, 1391 * so we must abort this transfer after cleanup 1392 */ 1393 if (urb->status != -EINPROGRESS) { 1394 done = true; 1395 if (status == 0) 1396 status = urb->status; 1397 } 1398 1399 if (done) { 1400 /* set status */ 1401 urb->status = status; 1402 urb->actual_length = qh->offset; 1403 musb_advance_schedule(musb, urb, hw_ep, USB_DIR_OUT); 1404 return; 1405 } else if ((usb_pipeisoc(pipe) || transfer_pending) && dma) { 1406 if (musb_tx_dma_program(musb->dma_controller, hw_ep, qh, urb, 1407 offset, length)) { 1408 if (is_cppi_enabled(musb) || tusb_dma_omap(musb)) 1409 musb_h_tx_dma_start(hw_ep); 1410 return; 1411 } 1412 } else if (tx_csr & MUSB_TXCSR_DMAENAB) { 1413 musb_dbg(musb, "not complete, but DMA enabled?"); 1414 return; 1415 } 1416 1417 /* 1418 * PIO: start next packet in this URB. 1419 * 1420 * REVISIT: some docs say that when hw_ep->tx_double_buffered, 1421 * (and presumably, FIFO is not half-full) we should write *two* 1422 * packets before updating TXCSR; other docs disagree... 1423 */ 1424 if (length > qh->maxpacket) 1425 length = qh->maxpacket; 1426 /* Unmap the buffer so that CPU can use it */ 1427 usb_hcd_unmap_urb_for_dma(musb->hcd, urb); 1428 1429 /* 1430 * We need to map sg if the transfer_buffer is 1431 * NULL. 1432 */ 1433 if (!urb->transfer_buffer) { 1434 /* sg_miter_start is already done in musb_ep_program */ 1435 if (!sg_miter_next(&qh->sg_miter)) { 1436 dev_err(musb->controller, "error: sg list empty\n"); 1437 sg_miter_stop(&qh->sg_miter); 1438 status = -EINVAL; 1439 goto done; 1440 } 1441 length = min_t(u32, length, qh->sg_miter.length); 1442 musb_write_fifo(hw_ep, length, qh->sg_miter.addr); 1443 qh->sg_miter.consumed = length; 1444 sg_miter_stop(&qh->sg_miter); 1445 } else { 1446 musb_write_fifo(hw_ep, length, urb->transfer_buffer + offset); 1447 } 1448 1449 qh->segsize = length; 1450 1451 musb_ep_select(mbase, epnum); 1452 musb_writew(epio, MUSB_TXCSR, 1453 MUSB_TXCSR_H_WZC_BITS | MUSB_TXCSR_TXPKTRDY); 1454 } 1455 1456 #ifdef CONFIG_USB_TI_CPPI41_DMA 1457 /* Seems to set up ISO for cppi41 and not advance len. See commit c57c41d */ 1458 static int musb_rx_dma_iso_cppi41(struct dma_controller *dma, 1459 struct musb_hw_ep *hw_ep, 1460 struct musb_qh *qh, 1461 struct urb *urb, 1462 size_t len) 1463 { 1464 struct dma_channel *channel = hw_ep->rx_channel; 1465 void __iomem *epio = hw_ep->regs; 1466 dma_addr_t *buf; 1467 u32 length; 1468 u16 val; 1469 1470 buf = (void *)urb->iso_frame_desc[qh->iso_idx].offset + 1471 (u32)urb->transfer_dma; 1472 1473 length = urb->iso_frame_desc[qh->iso_idx].length; 1474 1475 val = musb_readw(epio, MUSB_RXCSR); 1476 val |= MUSB_RXCSR_DMAENAB; 1477 musb_writew(hw_ep->regs, MUSB_RXCSR, val); 1478 1479 return dma->channel_program(channel, qh->maxpacket, 0, 1480 (u32)buf, length); 1481 } 1482 #else 1483 static inline int musb_rx_dma_iso_cppi41(struct dma_controller *dma, 1484 struct musb_hw_ep *hw_ep, 1485 struct musb_qh *qh, 1486 struct urb *urb, 1487 size_t len) 1488 { 1489 return false; 1490 } 1491 #endif 1492 1493 #if defined(CONFIG_USB_INVENTRA_DMA) || defined(CONFIG_USB_UX500_DMA) || \ 1494 defined(CONFIG_USB_TI_CPPI41_DMA) 1495 /* Host side RX (IN) using Mentor DMA works as follows: 1496 submit_urb -> 1497 - if queue was empty, ProgramEndpoint 1498 - first IN token is sent out (by setting ReqPkt) 1499 LinuxIsr -> RxReady() 1500 /\ => first packet is received 1501 | - Set in mode 0 (DmaEnab, ~ReqPkt) 1502 | -> DMA Isr (transfer complete) -> RxReady() 1503 | - Ack receive (~RxPktRdy), turn off DMA (~DmaEnab) 1504 | - if urb not complete, send next IN token (ReqPkt) 1505 | | else complete urb. 1506 | | 1507 --------------------------- 1508 * 1509 * Nuances of mode 1: 1510 * For short packets, no ack (+RxPktRdy) is sent automatically 1511 * (even if AutoClear is ON) 1512 * For full packets, ack (~RxPktRdy) and next IN token (+ReqPkt) is sent 1513 * automatically => major problem, as collecting the next packet becomes 1514 * difficult. Hence mode 1 is not used. 1515 * 1516 * REVISIT 1517 * All we care about at this driver level is that 1518 * (a) all URBs terminate with REQPKT cleared and fifo(s) empty; 1519 * (b) termination conditions are: short RX, or buffer full; 1520 * (c) fault modes include 1521 * - iff URB_SHORT_NOT_OK, short RX status is -EREMOTEIO. 1522 * (and that endpoint's dma queue stops immediately) 1523 * - overflow (full, PLUS more bytes in the terminal packet) 1524 * 1525 * So for example, usb-storage sets URB_SHORT_NOT_OK, and would 1526 * thus be a great candidate for using mode 1 ... for all but the 1527 * last packet of one URB's transfer. 1528 */ 1529 static int musb_rx_dma_inventra_cppi41(struct dma_controller *dma, 1530 struct musb_hw_ep *hw_ep, 1531 struct musb_qh *qh, 1532 struct urb *urb, 1533 size_t len) 1534 { 1535 struct dma_channel *channel = hw_ep->rx_channel; 1536 void __iomem *epio = hw_ep->regs; 1537 u16 val; 1538 int pipe; 1539 bool done; 1540 1541 pipe = urb->pipe; 1542 1543 if (usb_pipeisoc(pipe)) { 1544 struct usb_iso_packet_descriptor *d; 1545 1546 d = urb->iso_frame_desc + qh->iso_idx; 1547 d->actual_length = len; 1548 1549 /* even if there was an error, we did the dma 1550 * for iso_frame_desc->length 1551 */ 1552 if (d->status != -EILSEQ && d->status != -EOVERFLOW) 1553 d->status = 0; 1554 1555 if (++qh->iso_idx >= urb->number_of_packets) { 1556 done = true; 1557 } else { 1558 /* REVISIT: Why ignore return value here? */ 1559 if (musb_dma_cppi41(hw_ep->musb)) 1560 done = musb_rx_dma_iso_cppi41(dma, hw_ep, qh, 1561 urb, len); 1562 done = false; 1563 } 1564 1565 } else { 1566 /* done if urb buffer is full or short packet is recd */ 1567 done = (urb->actual_length + len >= 1568 urb->transfer_buffer_length 1569 || channel->actual_len < qh->maxpacket 1570 || channel->rx_packet_done); 1571 } 1572 1573 /* send IN token for next packet, without AUTOREQ */ 1574 if (!done) { 1575 val = musb_readw(epio, MUSB_RXCSR); 1576 val |= MUSB_RXCSR_H_REQPKT; 1577 musb_writew(epio, MUSB_RXCSR, MUSB_RXCSR_H_WZC_BITS | val); 1578 } 1579 1580 return done; 1581 } 1582 1583 /* Disadvantage of using mode 1: 1584 * It's basically usable only for mass storage class; essentially all 1585 * other protocols also terminate transfers on short packets. 1586 * 1587 * Details: 1588 * An extra IN token is sent at the end of the transfer (due to AUTOREQ) 1589 * If you try to use mode 1 for (transfer_buffer_length - 512), and try 1590 * to use the extra IN token to grab the last packet using mode 0, then 1591 * the problem is that you cannot be sure when the device will send the 1592 * last packet and RxPktRdy set. Sometimes the packet is recd too soon 1593 * such that it gets lost when RxCSR is re-set at the end of the mode 1 1594 * transfer, while sometimes it is recd just a little late so that if you 1595 * try to configure for mode 0 soon after the mode 1 transfer is 1596 * completed, you will find rxcount 0. Okay, so you might think why not 1597 * wait for an interrupt when the pkt is recd. Well, you won't get any! 1598 */ 1599 static int musb_rx_dma_in_inventra_cppi41(struct dma_controller *dma, 1600 struct musb_hw_ep *hw_ep, 1601 struct musb_qh *qh, 1602 struct urb *urb, 1603 size_t len, 1604 u8 iso_err) 1605 { 1606 struct musb *musb = hw_ep->musb; 1607 void __iomem *epio = hw_ep->regs; 1608 struct dma_channel *channel = hw_ep->rx_channel; 1609 u16 rx_count, val; 1610 int length, pipe, done; 1611 dma_addr_t buf; 1612 1613 rx_count = musb_readw(epio, MUSB_RXCOUNT); 1614 pipe = urb->pipe; 1615 1616 if (usb_pipeisoc(pipe)) { 1617 int d_status = 0; 1618 struct usb_iso_packet_descriptor *d; 1619 1620 d = urb->iso_frame_desc + qh->iso_idx; 1621 1622 if (iso_err) { 1623 d_status = -EILSEQ; 1624 urb->error_count++; 1625 } 1626 if (rx_count > d->length) { 1627 if (d_status == 0) { 1628 d_status = -EOVERFLOW; 1629 urb->error_count++; 1630 } 1631 musb_dbg(musb, "** OVERFLOW %d into %d", 1632 rx_count, d->length); 1633 1634 length = d->length; 1635 } else 1636 length = rx_count; 1637 d->status = d_status; 1638 buf = urb->transfer_dma + d->offset; 1639 } else { 1640 length = rx_count; 1641 buf = urb->transfer_dma + urb->actual_length; 1642 } 1643 1644 channel->desired_mode = 0; 1645 #ifdef USE_MODE1 1646 /* because of the issue below, mode 1 will 1647 * only rarely behave with correct semantics. 1648 */ 1649 if ((urb->transfer_flags & URB_SHORT_NOT_OK) 1650 && (urb->transfer_buffer_length - urb->actual_length) 1651 > qh->maxpacket) 1652 channel->desired_mode = 1; 1653 if (rx_count < hw_ep->max_packet_sz_rx) { 1654 length = rx_count; 1655 channel->desired_mode = 0; 1656 } else { 1657 length = urb->transfer_buffer_length; 1658 } 1659 #endif 1660 1661 /* See comments above on disadvantages of using mode 1 */ 1662 val = musb_readw(epio, MUSB_RXCSR); 1663 val &= ~MUSB_RXCSR_H_REQPKT; 1664 1665 if (channel->desired_mode == 0) 1666 val &= ~MUSB_RXCSR_H_AUTOREQ; 1667 else 1668 val |= MUSB_RXCSR_H_AUTOREQ; 1669 val |= MUSB_RXCSR_DMAENAB; 1670 1671 /* autoclear shouldn't be set in high bandwidth */ 1672 if (qh->hb_mult == 1) 1673 val |= MUSB_RXCSR_AUTOCLEAR; 1674 1675 musb_writew(epio, MUSB_RXCSR, MUSB_RXCSR_H_WZC_BITS | val); 1676 1677 /* REVISIT if when actual_length != 0, 1678 * transfer_buffer_length needs to be 1679 * adjusted first... 1680 */ 1681 done = dma->channel_program(channel, qh->maxpacket, 1682 channel->desired_mode, 1683 buf, length); 1684 1685 if (!done) { 1686 dma->channel_release(channel); 1687 hw_ep->rx_channel = NULL; 1688 channel = NULL; 1689 val = musb_readw(epio, MUSB_RXCSR); 1690 val &= ~(MUSB_RXCSR_DMAENAB 1691 | MUSB_RXCSR_H_AUTOREQ 1692 | MUSB_RXCSR_AUTOCLEAR); 1693 musb_writew(epio, MUSB_RXCSR, val); 1694 } 1695 1696 return done; 1697 } 1698 #else 1699 static inline int musb_rx_dma_inventra_cppi41(struct dma_controller *dma, 1700 struct musb_hw_ep *hw_ep, 1701 struct musb_qh *qh, 1702 struct urb *urb, 1703 size_t len) 1704 { 1705 return false; 1706 } 1707 1708 static inline int musb_rx_dma_in_inventra_cppi41(struct dma_controller *dma, 1709 struct musb_hw_ep *hw_ep, 1710 struct musb_qh *qh, 1711 struct urb *urb, 1712 size_t len, 1713 u8 iso_err) 1714 { 1715 return false; 1716 } 1717 #endif 1718 1719 /* 1720 * Service an RX interrupt for the given IN endpoint; docs cover bulk, iso, 1721 * and high-bandwidth IN transfer cases. 1722 */ 1723 void musb_host_rx(struct musb *musb, u8 epnum) 1724 { 1725 struct urb *urb; 1726 struct musb_hw_ep *hw_ep = musb->endpoints + epnum; 1727 struct dma_controller *c = musb->dma_controller; 1728 void __iomem *epio = hw_ep->regs; 1729 struct musb_qh *qh = hw_ep->in_qh; 1730 size_t xfer_len; 1731 void __iomem *mbase = musb->mregs; 1732 u16 rx_csr, val; 1733 bool iso_err = false; 1734 bool done = false; 1735 u32 status; 1736 struct dma_channel *dma; 1737 unsigned int sg_flags = SG_MITER_ATOMIC | SG_MITER_TO_SG; 1738 1739 musb_ep_select(mbase, epnum); 1740 1741 urb = next_urb(qh); 1742 dma = is_dma_capable() ? hw_ep->rx_channel : NULL; 1743 status = 0; 1744 xfer_len = 0; 1745 1746 rx_csr = musb_readw(epio, MUSB_RXCSR); 1747 val = rx_csr; 1748 1749 if (unlikely(!urb)) { 1750 /* REVISIT -- THIS SHOULD NEVER HAPPEN ... but, at least 1751 * usbtest #11 (unlinks) triggers it regularly, sometimes 1752 * with fifo full. (Only with DMA??) 1753 */ 1754 musb_dbg(musb, "BOGUS RX%d ready, csr %04x, count %d", 1755 epnum, val, musb_readw(epio, MUSB_RXCOUNT)); 1756 musb_h_flush_rxfifo(hw_ep, MUSB_RXCSR_CLRDATATOG); 1757 return; 1758 } 1759 1760 trace_musb_urb_rx(musb, urb); 1761 1762 /* check for errors, concurrent stall & unlink is not really 1763 * handled yet! */ 1764 if (rx_csr & MUSB_RXCSR_H_RXSTALL) { 1765 musb_dbg(musb, "RX end %d STALL", epnum); 1766 1767 /* stall; record URB status */ 1768 status = -EPIPE; 1769 1770 } else if (rx_csr & MUSB_RXCSR_H_ERROR) { 1771 dev_err(musb->controller, "ep%d RX three-strikes error", epnum); 1772 1773 /* 1774 * The three-strikes error could only happen when the USB 1775 * device is not accessible, for example detached or powered 1776 * off. So return the fatal error -ESHUTDOWN so hopefully the 1777 * USB device drivers won't immediately resubmit the same URB. 1778 */ 1779 status = -ESHUTDOWN; 1780 musb_writeb(epio, MUSB_RXINTERVAL, 0); 1781 1782 rx_csr &= ~MUSB_RXCSR_H_ERROR; 1783 musb_writew(epio, MUSB_RXCSR, rx_csr); 1784 1785 } else if (rx_csr & MUSB_RXCSR_DATAERROR) { 1786 1787 if (USB_ENDPOINT_XFER_ISOC != qh->type) { 1788 musb_dbg(musb, "RX end %d NAK timeout", epnum); 1789 1790 /* NOTE: NAKing is *NOT* an error, so we want to 1791 * continue. Except ... if there's a request for 1792 * another QH, use that instead of starving it. 1793 * 1794 * Devices like Ethernet and serial adapters keep 1795 * reads posted at all times, which will starve 1796 * other devices without this logic. 1797 */ 1798 if (usb_pipebulk(urb->pipe) 1799 && qh->mux == 1 1800 && !list_is_singular(&musb->in_bulk)) { 1801 musb_bulk_nak_timeout(musb, hw_ep, 1); 1802 return; 1803 } 1804 musb_ep_select(mbase, epnum); 1805 rx_csr |= MUSB_RXCSR_H_WZC_BITS; 1806 rx_csr &= ~MUSB_RXCSR_DATAERROR; 1807 musb_writew(epio, MUSB_RXCSR, rx_csr); 1808 1809 goto finish; 1810 } else { 1811 musb_dbg(musb, "RX end %d ISO data error", epnum); 1812 /* packet error reported later */ 1813 iso_err = true; 1814 } 1815 } else if (rx_csr & MUSB_RXCSR_INCOMPRX) { 1816 musb_dbg(musb, "end %d high bandwidth incomplete ISO packet RX", 1817 epnum); 1818 status = -EPROTO; 1819 } 1820 1821 /* faults abort the transfer */ 1822 if (status) { 1823 /* clean up dma and collect transfer count */ 1824 if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { 1825 dma->status = MUSB_DMA_STATUS_CORE_ABORT; 1826 musb->dma_controller->channel_abort(dma); 1827 xfer_len = dma->actual_len; 1828 } 1829 musb_h_flush_rxfifo(hw_ep, MUSB_RXCSR_CLRDATATOG); 1830 musb_writeb(epio, MUSB_RXINTERVAL, 0); 1831 done = true; 1832 goto finish; 1833 } 1834 1835 if (unlikely(dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY)) { 1836 /* SHOULD NEVER HAPPEN ... but at least DaVinci has done it */ 1837 ERR("RX%d dma busy, csr %04x\n", epnum, rx_csr); 1838 goto finish; 1839 } 1840 1841 /* thorough shutdown for now ... given more precise fault handling 1842 * and better queueing support, we might keep a DMA pipeline going 1843 * while processing this irq for earlier completions. 1844 */ 1845 1846 /* FIXME this is _way_ too much in-line logic for Mentor DMA */ 1847 if (!musb_dma_inventra(musb) && !musb_dma_ux500(musb) && 1848 (rx_csr & MUSB_RXCSR_H_REQPKT)) { 1849 /* REVISIT this happened for a while on some short reads... 1850 * the cleanup still needs investigation... looks bad... 1851 * and also duplicates dma cleanup code above ... plus, 1852 * shouldn't this be the "half full" double buffer case? 1853 */ 1854 if (dma_channel_status(dma) == MUSB_DMA_STATUS_BUSY) { 1855 dma->status = MUSB_DMA_STATUS_CORE_ABORT; 1856 musb->dma_controller->channel_abort(dma); 1857 xfer_len = dma->actual_len; 1858 done = true; 1859 } 1860 1861 musb_dbg(musb, "RXCSR%d %04x, reqpkt, len %zu%s", epnum, rx_csr, 1862 xfer_len, dma ? ", dma" : ""); 1863 rx_csr &= ~MUSB_RXCSR_H_REQPKT; 1864 1865 musb_ep_select(mbase, epnum); 1866 musb_writew(epio, MUSB_RXCSR, 1867 MUSB_RXCSR_H_WZC_BITS | rx_csr); 1868 } 1869 1870 if (dma && (rx_csr & MUSB_RXCSR_DMAENAB)) { 1871 xfer_len = dma->actual_len; 1872 1873 val &= ~(MUSB_RXCSR_DMAENAB 1874 | MUSB_RXCSR_H_AUTOREQ 1875 | MUSB_RXCSR_AUTOCLEAR 1876 | MUSB_RXCSR_RXPKTRDY); 1877 musb_writew(hw_ep->regs, MUSB_RXCSR, val); 1878 1879 if (musb_dma_inventra(musb) || musb_dma_ux500(musb) || 1880 musb_dma_cppi41(musb)) { 1881 done = musb_rx_dma_inventra_cppi41(c, hw_ep, qh, urb, xfer_len); 1882 musb_dbg(hw_ep->musb, 1883 "ep %d dma %s, rxcsr %04x, rxcount %d", 1884 epnum, done ? "off" : "reset", 1885 musb_readw(epio, MUSB_RXCSR), 1886 musb_readw(epio, MUSB_RXCOUNT)); 1887 } else { 1888 done = true; 1889 } 1890 1891 } else if (urb->status == -EINPROGRESS) { 1892 /* if no errors, be sure a packet is ready for unloading */ 1893 if (unlikely(!(rx_csr & MUSB_RXCSR_RXPKTRDY))) { 1894 status = -EPROTO; 1895 ERR("Rx interrupt with no errors or packet!\n"); 1896 1897 /* FIXME this is another "SHOULD NEVER HAPPEN" */ 1898 1899 /* SCRUB (RX) */ 1900 /* do the proper sequence to abort the transfer */ 1901 musb_ep_select(mbase, epnum); 1902 val &= ~MUSB_RXCSR_H_REQPKT; 1903 musb_writew(epio, MUSB_RXCSR, val); 1904 goto finish; 1905 } 1906 1907 /* we are expecting IN packets */ 1908 if ((musb_dma_inventra(musb) || musb_dma_ux500(musb) || 1909 musb_dma_cppi41(musb)) && dma) { 1910 musb_dbg(hw_ep->musb, 1911 "RX%d count %d, buffer 0x%llx len %d/%d", 1912 epnum, musb_readw(epio, MUSB_RXCOUNT), 1913 (unsigned long long) urb->transfer_dma 1914 + urb->actual_length, 1915 qh->offset, 1916 urb->transfer_buffer_length); 1917 1918 if (musb_rx_dma_in_inventra_cppi41(c, hw_ep, qh, urb, 1919 xfer_len, iso_err)) 1920 goto finish; 1921 else 1922 dev_err(musb->controller, "error: rx_dma failed\n"); 1923 } 1924 1925 if (!dma) { 1926 unsigned int received_len; 1927 1928 /* Unmap the buffer so that CPU can use it */ 1929 usb_hcd_unmap_urb_for_dma(musb->hcd, urb); 1930 1931 /* 1932 * We need to map sg if the transfer_buffer is 1933 * NULL. 1934 */ 1935 if (!urb->transfer_buffer) { 1936 qh->use_sg = true; 1937 sg_miter_start(&qh->sg_miter, urb->sg, 1, 1938 sg_flags); 1939 } 1940 1941 if (qh->use_sg) { 1942 if (!sg_miter_next(&qh->sg_miter)) { 1943 dev_err(musb->controller, "error: sg list empty\n"); 1944 sg_miter_stop(&qh->sg_miter); 1945 status = -EINVAL; 1946 done = true; 1947 goto finish; 1948 } 1949 urb->transfer_buffer = qh->sg_miter.addr; 1950 received_len = urb->actual_length; 1951 qh->offset = 0x0; 1952 done = musb_host_packet_rx(musb, urb, epnum, 1953 iso_err); 1954 /* Calculate the number of bytes received */ 1955 received_len = urb->actual_length - 1956 received_len; 1957 qh->sg_miter.consumed = received_len; 1958 sg_miter_stop(&qh->sg_miter); 1959 } else { 1960 done = musb_host_packet_rx(musb, urb, 1961 epnum, iso_err); 1962 } 1963 musb_dbg(musb, "read %spacket", done ? "last " : ""); 1964 } 1965 } 1966 1967 finish: 1968 urb->actual_length += xfer_len; 1969 qh->offset += xfer_len; 1970 if (done) { 1971 if (qh->use_sg) { 1972 qh->use_sg = false; 1973 urb->transfer_buffer = NULL; 1974 } 1975 1976 if (urb->status == -EINPROGRESS) 1977 urb->status = status; 1978 musb_advance_schedule(musb, urb, hw_ep, USB_DIR_IN); 1979 } 1980 } 1981 1982 /* schedule nodes correspond to peripheral endpoints, like an OHCI QH. 1983 * the software schedule associates multiple such nodes with a given 1984 * host side hardware endpoint + direction; scheduling may activate 1985 * that hardware endpoint. 1986 */ 1987 static int musb_schedule( 1988 struct musb *musb, 1989 struct musb_qh *qh, 1990 int is_in) 1991 { 1992 int idle = 0; 1993 int best_diff; 1994 int best_end, epnum; 1995 struct musb_hw_ep *hw_ep = NULL; 1996 struct list_head *head = NULL; 1997 u8 toggle; 1998 u8 txtype; 1999 struct urb *urb = next_urb(qh); 2000 2001 /* use fixed hardware for control and bulk */ 2002 if (qh->type == USB_ENDPOINT_XFER_CONTROL) { 2003 head = &musb->control; 2004 hw_ep = musb->control_ep; 2005 goto success; 2006 } 2007 2008 /* else, periodic transfers get muxed to other endpoints */ 2009 2010 /* 2011 * We know this qh hasn't been scheduled, so all we need to do 2012 * is choose which hardware endpoint to put it on ... 2013 * 2014 * REVISIT what we really want here is a regular schedule tree 2015 * like e.g. OHCI uses. 2016 */ 2017 best_diff = 4096; 2018 best_end = -1; 2019 2020 for (epnum = 1, hw_ep = musb->endpoints + 1; 2021 epnum < musb->nr_endpoints; 2022 epnum++, hw_ep++) { 2023 int diff; 2024 2025 if (musb_ep_get_qh(hw_ep, is_in) != NULL) 2026 continue; 2027 2028 if (hw_ep == musb->bulk_ep) 2029 continue; 2030 2031 if (is_in) 2032 diff = hw_ep->max_packet_sz_rx; 2033 else 2034 diff = hw_ep->max_packet_sz_tx; 2035 diff -= (qh->maxpacket * qh->hb_mult); 2036 2037 if (diff >= 0 && best_diff > diff) { 2038 2039 /* 2040 * Mentor controller has a bug in that if we schedule 2041 * a BULK Tx transfer on an endpoint that had earlier 2042 * handled ISOC then the BULK transfer has to start on 2043 * a zero toggle. If the BULK transfer starts on a 1 2044 * toggle then this transfer will fail as the mentor 2045 * controller starts the Bulk transfer on a 0 toggle 2046 * irrespective of the programming of the toggle bits 2047 * in the TXCSR register. Check for this condition 2048 * while allocating the EP for a Tx Bulk transfer. If 2049 * so skip this EP. 2050 */ 2051 hw_ep = musb->endpoints + epnum; 2052 toggle = usb_gettoggle(urb->dev, qh->epnum, !is_in); 2053 txtype = (musb_readb(hw_ep->regs, MUSB_TXTYPE) 2054 >> 4) & 0x3; 2055 if (!is_in && (qh->type == USB_ENDPOINT_XFER_BULK) && 2056 toggle && (txtype == USB_ENDPOINT_XFER_ISOC)) 2057 continue; 2058 2059 best_diff = diff; 2060 best_end = epnum; 2061 } 2062 } 2063 /* use bulk reserved ep1 if no other ep is free */ 2064 if (best_end < 0 && qh->type == USB_ENDPOINT_XFER_BULK) { 2065 hw_ep = musb->bulk_ep; 2066 if (is_in) 2067 head = &musb->in_bulk; 2068 else 2069 head = &musb->out_bulk; 2070 2071 /* Enable bulk RX/TX NAK timeout scheme when bulk requests are 2072 * multiplexed. This scheme does not work in high speed to full 2073 * speed scenario as NAK interrupts are not coming from a 2074 * full speed device connected to a high speed device. 2075 * NAK timeout interval is 8 (128 uframe or 16ms) for HS and 2076 * 4 (8 frame or 8ms) for FS device. 2077 */ 2078 if (qh->dev) 2079 qh->intv_reg = 2080 (USB_SPEED_HIGH == qh->dev->speed) ? 8 : 4; 2081 goto success; 2082 } else if (best_end < 0) { 2083 dev_err(musb->controller, 2084 "%s hwep alloc failed for %dx%d\n", 2085 musb_ep_xfertype_string(qh->type), 2086 qh->hb_mult, qh->maxpacket); 2087 return -ENOSPC; 2088 } 2089 2090 idle = 1; 2091 qh->mux = 0; 2092 hw_ep = musb->endpoints + best_end; 2093 musb_dbg(musb, "qh %p periodic slot %d", qh, best_end); 2094 success: 2095 if (head) { 2096 idle = list_empty(head); 2097 list_add_tail(&qh->ring, head); 2098 qh->mux = 1; 2099 } 2100 qh->hw_ep = hw_ep; 2101 qh->hep->hcpriv = qh; 2102 if (idle) 2103 musb_start_urb(musb, is_in, qh); 2104 return 0; 2105 } 2106 2107 static int musb_urb_enqueue( 2108 struct usb_hcd *hcd, 2109 struct urb *urb, 2110 gfp_t mem_flags) 2111 { 2112 unsigned long flags; 2113 struct musb *musb = hcd_to_musb(hcd); 2114 struct usb_host_endpoint *hep = urb->ep; 2115 struct musb_qh *qh; 2116 struct usb_endpoint_descriptor *epd = &hep->desc; 2117 int ret; 2118 unsigned type_reg; 2119 unsigned interval; 2120 2121 /* host role must be active */ 2122 if (!is_host_active(musb) || !musb->is_active) 2123 return -ENODEV; 2124 2125 trace_musb_urb_enq(musb, urb); 2126 2127 spin_lock_irqsave(&musb->lock, flags); 2128 ret = usb_hcd_link_urb_to_ep(hcd, urb); 2129 qh = ret ? NULL : hep->hcpriv; 2130 if (qh) 2131 urb->hcpriv = qh; 2132 spin_unlock_irqrestore(&musb->lock, flags); 2133 2134 /* DMA mapping was already done, if needed, and this urb is on 2135 * hep->urb_list now ... so we're done, unless hep wasn't yet 2136 * scheduled onto a live qh. 2137 * 2138 * REVISIT best to keep hep->hcpriv valid until the endpoint gets 2139 * disabled, testing for empty qh->ring and avoiding qh setup costs 2140 * except for the first urb queued after a config change. 2141 */ 2142 if (qh || ret) 2143 return ret; 2144 2145 /* Allocate and initialize qh, minimizing the work done each time 2146 * hw_ep gets reprogrammed, or with irqs blocked. Then schedule it. 2147 * 2148 * REVISIT consider a dedicated qh kmem_cache, so it's harder 2149 * for bugs in other kernel code to break this driver... 2150 */ 2151 qh = kzalloc(sizeof *qh, mem_flags); 2152 if (!qh) { 2153 spin_lock_irqsave(&musb->lock, flags); 2154 usb_hcd_unlink_urb_from_ep(hcd, urb); 2155 spin_unlock_irqrestore(&musb->lock, flags); 2156 return -ENOMEM; 2157 } 2158 2159 qh->hep = hep; 2160 qh->dev = urb->dev; 2161 INIT_LIST_HEAD(&qh->ring); 2162 qh->is_ready = 1; 2163 2164 qh->maxpacket = usb_endpoint_maxp(epd); 2165 qh->type = usb_endpoint_type(epd); 2166 2167 /* Bits 11 & 12 of wMaxPacketSize encode high bandwidth multiplier. 2168 * Some musb cores don't support high bandwidth ISO transfers; and 2169 * we don't (yet!) support high bandwidth interrupt transfers. 2170 */ 2171 qh->hb_mult = usb_endpoint_maxp_mult(epd); 2172 if (qh->hb_mult > 1) { 2173 int ok = (qh->type == USB_ENDPOINT_XFER_ISOC); 2174 2175 if (ok) 2176 ok = (usb_pipein(urb->pipe) && musb->hb_iso_rx) 2177 || (usb_pipeout(urb->pipe) && musb->hb_iso_tx); 2178 if (!ok) { 2179 dev_err(musb->controller, 2180 "high bandwidth %s (%dx%d) not supported\n", 2181 musb_ep_xfertype_string(qh->type), 2182 qh->hb_mult, qh->maxpacket & 0x7ff); 2183 ret = -EMSGSIZE; 2184 goto done; 2185 } 2186 qh->maxpacket &= 0x7ff; 2187 } 2188 2189 qh->epnum = usb_endpoint_num(epd); 2190 2191 /* NOTE: urb->dev->devnum is wrong during SET_ADDRESS */ 2192 qh->addr_reg = (u8) usb_pipedevice(urb->pipe); 2193 2194 /* precompute rxtype/txtype/type0 register */ 2195 type_reg = (qh->type << 4) | qh->epnum; 2196 switch (urb->dev->speed) { 2197 case USB_SPEED_LOW: 2198 type_reg |= 0xc0; 2199 break; 2200 case USB_SPEED_FULL: 2201 type_reg |= 0x80; 2202 break; 2203 default: 2204 type_reg |= 0x40; 2205 } 2206 qh->type_reg = type_reg; 2207 2208 /* Precompute RXINTERVAL/TXINTERVAL register */ 2209 switch (qh->type) { 2210 case USB_ENDPOINT_XFER_INT: 2211 /* 2212 * Full/low speeds use the linear encoding, 2213 * high speed uses the logarithmic encoding. 2214 */ 2215 if (urb->dev->speed <= USB_SPEED_FULL) { 2216 interval = max_t(u8, epd->bInterval, 1); 2217 break; 2218 } 2219 fallthrough; 2220 case USB_ENDPOINT_XFER_ISOC: 2221 /* ISO always uses logarithmic encoding */ 2222 interval = min_t(u8, epd->bInterval, 16); 2223 break; 2224 default: 2225 /* REVISIT we actually want to use NAK limits, hinting to the 2226 * transfer scheduling logic to try some other qh, e.g. try 2227 * for 2 msec first: 2228 * 2229 * interval = (USB_SPEED_HIGH == urb->dev->speed) ? 16 : 2; 2230 * 2231 * The downside of disabling this is that transfer scheduling 2232 * gets VERY unfair for nonperiodic transfers; a misbehaving 2233 * peripheral could make that hurt. That's perfectly normal 2234 * for reads from network or serial adapters ... so we have 2235 * partial NAKlimit support for bulk RX. 2236 * 2237 * The upside of disabling it is simpler transfer scheduling. 2238 */ 2239 interval = 0; 2240 } 2241 qh->intv_reg = interval; 2242 2243 /* precompute addressing for external hub/tt ports */ 2244 if (musb->is_multipoint) { 2245 struct usb_device *parent = urb->dev->parent; 2246 2247 if (parent != hcd->self.root_hub) { 2248 qh->h_addr_reg = (u8) parent->devnum; 2249 2250 /* set up tt info if needed */ 2251 if (urb->dev->tt) { 2252 qh->h_port_reg = (u8) urb->dev->ttport; 2253 if (urb->dev->tt->hub) 2254 qh->h_addr_reg = 2255 (u8) urb->dev->tt->hub->devnum; 2256 if (urb->dev->tt->multi) 2257 qh->h_addr_reg |= 0x80; 2258 } 2259 } 2260 } 2261 2262 /* invariant: hep->hcpriv is null OR the qh that's already scheduled. 2263 * until we get real dma queues (with an entry for each urb/buffer), 2264 * we only have work to do in the former case. 2265 */ 2266 spin_lock_irqsave(&musb->lock, flags); 2267 if (hep->hcpriv || !next_urb(qh)) { 2268 /* some concurrent activity submitted another urb to hep... 2269 * odd, rare, error prone, but legal. 2270 */ 2271 kfree(qh); 2272 qh = NULL; 2273 ret = 0; 2274 } else 2275 ret = musb_schedule(musb, qh, 2276 epd->bEndpointAddress & USB_ENDPOINT_DIR_MASK); 2277 2278 if (ret == 0) { 2279 urb->hcpriv = qh; 2280 /* FIXME set urb->start_frame for iso/intr, it's tested in 2281 * musb_start_urb(), but otherwise only konicawc cares ... 2282 */ 2283 } 2284 spin_unlock_irqrestore(&musb->lock, flags); 2285 2286 done: 2287 if (ret != 0) { 2288 spin_lock_irqsave(&musb->lock, flags); 2289 usb_hcd_unlink_urb_from_ep(hcd, urb); 2290 spin_unlock_irqrestore(&musb->lock, flags); 2291 kfree(qh); 2292 } 2293 return ret; 2294 } 2295 2296 2297 /* 2298 * abort a transfer that's at the head of a hardware queue. 2299 * called with controller locked, irqs blocked 2300 * that hardware queue advances to the next transfer, unless prevented 2301 */ 2302 static int musb_cleanup_urb(struct urb *urb, struct musb_qh *qh) 2303 { 2304 struct musb_hw_ep *ep = qh->hw_ep; 2305 struct musb *musb = ep->musb; 2306 void __iomem *epio = ep->regs; 2307 unsigned hw_end = ep->epnum; 2308 void __iomem *regs = ep->musb->mregs; 2309 int is_in = usb_pipein(urb->pipe); 2310 int status = 0; 2311 u16 csr; 2312 struct dma_channel *dma = NULL; 2313 2314 musb_ep_select(regs, hw_end); 2315 2316 if (is_dma_capable()) { 2317 dma = is_in ? ep->rx_channel : ep->tx_channel; 2318 if (dma) { 2319 status = ep->musb->dma_controller->channel_abort(dma); 2320 musb_dbg(musb, "abort %cX%d DMA for urb %p --> %d", 2321 is_in ? 'R' : 'T', ep->epnum, 2322 urb, status); 2323 urb->actual_length += dma->actual_len; 2324 } 2325 } 2326 2327 /* turn off DMA requests, discard state, stop polling ... */ 2328 if (ep->epnum && is_in) { 2329 /* giveback saves bulk toggle */ 2330 csr = musb_h_flush_rxfifo(ep, 0); 2331 2332 /* clear the endpoint's irq status here to avoid bogus irqs */ 2333 if (is_dma_capable() && dma) 2334 musb_platform_clear_ep_rxintr(musb, ep->epnum); 2335 } else if (ep->epnum) { 2336 musb_h_tx_flush_fifo(ep); 2337 csr = musb_readw(epio, MUSB_TXCSR); 2338 csr &= ~(MUSB_TXCSR_AUTOSET 2339 | MUSB_TXCSR_DMAENAB 2340 | MUSB_TXCSR_H_RXSTALL 2341 | MUSB_TXCSR_H_NAKTIMEOUT 2342 | MUSB_TXCSR_H_ERROR 2343 | MUSB_TXCSR_TXPKTRDY); 2344 musb_writew(epio, MUSB_TXCSR, csr); 2345 /* REVISIT may need to clear FLUSHFIFO ... */ 2346 musb_writew(epio, MUSB_TXCSR, csr); 2347 /* flush cpu writebuffer */ 2348 csr = musb_readw(epio, MUSB_TXCSR); 2349 } else { 2350 musb_h_ep0_flush_fifo(ep); 2351 } 2352 if (status == 0) 2353 musb_advance_schedule(ep->musb, urb, ep, is_in); 2354 return status; 2355 } 2356 2357 static int musb_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status) 2358 { 2359 struct musb *musb = hcd_to_musb(hcd); 2360 struct musb_qh *qh; 2361 unsigned long flags; 2362 int is_in = usb_pipein(urb->pipe); 2363 int ret; 2364 2365 trace_musb_urb_deq(musb, urb); 2366 2367 spin_lock_irqsave(&musb->lock, flags); 2368 ret = usb_hcd_check_unlink_urb(hcd, urb, status); 2369 if (ret) 2370 goto done; 2371 2372 qh = urb->hcpriv; 2373 if (!qh) 2374 goto done; 2375 2376 /* 2377 * Any URB not actively programmed into endpoint hardware can be 2378 * immediately given back; that's any URB not at the head of an 2379 * endpoint queue, unless someday we get real DMA queues. And even 2380 * if it's at the head, it might not be known to the hardware... 2381 * 2382 * Otherwise abort current transfer, pending DMA, etc.; urb->status 2383 * has already been updated. This is a synchronous abort; it'd be 2384 * OK to hold off until after some IRQ, though. 2385 * 2386 * NOTE: qh is invalid unless !list_empty(&hep->urb_list) 2387 */ 2388 if (!qh->is_ready 2389 || urb->urb_list.prev != &qh->hep->urb_list 2390 || musb_ep_get_qh(qh->hw_ep, is_in) != qh) { 2391 int ready = qh->is_ready; 2392 2393 qh->is_ready = 0; 2394 musb_giveback(musb, urb, 0); 2395 qh->is_ready = ready; 2396 2397 /* If nothing else (usually musb_giveback) is using it 2398 * and its URB list has emptied, recycle this qh. 2399 */ 2400 if (ready && list_empty(&qh->hep->urb_list)) { 2401 qh->hep->hcpriv = NULL; 2402 list_del(&qh->ring); 2403 kfree(qh); 2404 } 2405 } else 2406 ret = musb_cleanup_urb(urb, qh); 2407 done: 2408 spin_unlock_irqrestore(&musb->lock, flags); 2409 return ret; 2410 } 2411 2412 /* disable an endpoint */ 2413 static void 2414 musb_h_disable(struct usb_hcd *hcd, struct usb_host_endpoint *hep) 2415 { 2416 u8 is_in = hep->desc.bEndpointAddress & USB_DIR_IN; 2417 unsigned long flags; 2418 struct musb *musb = hcd_to_musb(hcd); 2419 struct musb_qh *qh; 2420 struct urb *urb; 2421 2422 spin_lock_irqsave(&musb->lock, flags); 2423 2424 qh = hep->hcpriv; 2425 if (qh == NULL) 2426 goto exit; 2427 2428 /* NOTE: qh is invalid unless !list_empty(&hep->urb_list) */ 2429 2430 /* Kick the first URB off the hardware, if needed */ 2431 qh->is_ready = 0; 2432 if (musb_ep_get_qh(qh->hw_ep, is_in) == qh) { 2433 urb = next_urb(qh); 2434 2435 /* make software (then hardware) stop ASAP */ 2436 if (!urb->unlinked) 2437 urb->status = -ESHUTDOWN; 2438 2439 /* cleanup */ 2440 musb_cleanup_urb(urb, qh); 2441 2442 /* Then nuke all the others ... and advance the 2443 * queue on hw_ep (e.g. bulk ring) when we're done. 2444 */ 2445 while (!list_empty(&hep->urb_list)) { 2446 urb = next_urb(qh); 2447 urb->status = -ESHUTDOWN; 2448 musb_advance_schedule(musb, urb, qh->hw_ep, is_in); 2449 } 2450 } else { 2451 /* Just empty the queue; the hardware is busy with 2452 * other transfers, and since !qh->is_ready nothing 2453 * will activate any of these as it advances. 2454 */ 2455 while (!list_empty(&hep->urb_list)) 2456 musb_giveback(musb, next_urb(qh), -ESHUTDOWN); 2457 2458 hep->hcpriv = NULL; 2459 list_del(&qh->ring); 2460 kfree(qh); 2461 } 2462 exit: 2463 spin_unlock_irqrestore(&musb->lock, flags); 2464 } 2465 2466 static int musb_h_get_frame_number(struct usb_hcd *hcd) 2467 { 2468 struct musb *musb = hcd_to_musb(hcd); 2469 2470 return musb_readw(musb->mregs, MUSB_FRAME); 2471 } 2472 2473 static int musb_h_start(struct usb_hcd *hcd) 2474 { 2475 struct musb *musb = hcd_to_musb(hcd); 2476 2477 /* NOTE: musb_start() is called when the hub driver turns 2478 * on port power, or when (OTG) peripheral starts. 2479 */ 2480 hcd->state = HC_STATE_RUNNING; 2481 musb->port1_status = 0; 2482 return 0; 2483 } 2484 2485 static void musb_h_stop(struct usb_hcd *hcd) 2486 { 2487 musb_stop(hcd_to_musb(hcd)); 2488 hcd->state = HC_STATE_HALT; 2489 } 2490 2491 static int musb_bus_suspend(struct usb_hcd *hcd) 2492 { 2493 struct musb *musb = hcd_to_musb(hcd); 2494 u8 devctl; 2495 int ret; 2496 2497 ret = musb_port_suspend(musb, true); 2498 if (ret) 2499 return ret; 2500 2501 if (!is_host_active(musb)) 2502 return 0; 2503 2504 switch (musb_get_state(musb)) { 2505 case OTG_STATE_A_SUSPEND: 2506 return 0; 2507 case OTG_STATE_A_WAIT_VRISE: 2508 /* ID could be grounded even if there's no device 2509 * on the other end of the cable. NOTE that the 2510 * A_WAIT_VRISE timers are messy with MUSB... 2511 */ 2512 devctl = musb_readb(musb->mregs, MUSB_DEVCTL); 2513 if ((devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS) 2514 musb_set_state(musb, OTG_STATE_A_WAIT_BCON); 2515 break; 2516 default: 2517 break; 2518 } 2519 2520 if (musb->is_active) { 2521 WARNING("trying to suspend as %s while active\n", 2522 musb_otg_state_string(musb)); 2523 return -EBUSY; 2524 } else 2525 return 0; 2526 } 2527 2528 static int musb_bus_resume(struct usb_hcd *hcd) 2529 { 2530 struct musb *musb = hcd_to_musb(hcd); 2531 2532 if (musb->config && 2533 musb->config->host_port_deassert_reset_at_resume) 2534 musb_port_reset(musb, false); 2535 2536 return 0; 2537 } 2538 2539 #ifndef CONFIG_MUSB_PIO_ONLY 2540 2541 #define MUSB_USB_DMA_ALIGN 4 2542 2543 struct musb_temp_buffer { 2544 void *kmalloc_ptr; 2545 void *old_xfer_buffer; 2546 u8 data[]; 2547 }; 2548 2549 static void musb_free_temp_buffer(struct urb *urb) 2550 { 2551 enum dma_data_direction dir; 2552 struct musb_temp_buffer *temp; 2553 size_t length; 2554 2555 if (!(urb->transfer_flags & URB_ALIGNED_TEMP_BUFFER)) 2556 return; 2557 2558 dir = usb_urb_dir_in(urb) ? DMA_FROM_DEVICE : DMA_TO_DEVICE; 2559 2560 temp = container_of(urb->transfer_buffer, struct musb_temp_buffer, 2561 data); 2562 2563 if (dir == DMA_FROM_DEVICE) { 2564 if (usb_pipeisoc(urb->pipe)) 2565 length = urb->transfer_buffer_length; 2566 else 2567 length = urb->actual_length; 2568 2569 memcpy(temp->old_xfer_buffer, temp->data, length); 2570 } 2571 urb->transfer_buffer = temp->old_xfer_buffer; 2572 kfree(temp->kmalloc_ptr); 2573 2574 urb->transfer_flags &= ~URB_ALIGNED_TEMP_BUFFER; 2575 } 2576 2577 static int musb_alloc_temp_buffer(struct urb *urb, gfp_t mem_flags) 2578 { 2579 enum dma_data_direction dir; 2580 struct musb_temp_buffer *temp; 2581 void *kmalloc_ptr; 2582 size_t kmalloc_size; 2583 2584 if (urb->num_sgs || urb->sg || 2585 urb->transfer_buffer_length == 0 || 2586 !((uintptr_t)urb->transfer_buffer & (MUSB_USB_DMA_ALIGN - 1))) 2587 return 0; 2588 2589 dir = usb_urb_dir_in(urb) ? DMA_FROM_DEVICE : DMA_TO_DEVICE; 2590 2591 /* Allocate a buffer with enough padding for alignment */ 2592 kmalloc_size = urb->transfer_buffer_length + 2593 sizeof(struct musb_temp_buffer) + MUSB_USB_DMA_ALIGN - 1; 2594 2595 kmalloc_ptr = kmalloc(kmalloc_size, mem_flags); 2596 if (!kmalloc_ptr) 2597 return -ENOMEM; 2598 2599 /* Position our struct temp_buffer such that data is aligned */ 2600 temp = PTR_ALIGN(kmalloc_ptr, MUSB_USB_DMA_ALIGN); 2601 2602 2603 temp->kmalloc_ptr = kmalloc_ptr; 2604 temp->old_xfer_buffer = urb->transfer_buffer; 2605 if (dir == DMA_TO_DEVICE) 2606 memcpy(temp->data, urb->transfer_buffer, 2607 urb->transfer_buffer_length); 2608 urb->transfer_buffer = temp->data; 2609 2610 urb->transfer_flags |= URB_ALIGNED_TEMP_BUFFER; 2611 2612 return 0; 2613 } 2614 2615 static int musb_map_urb_for_dma(struct usb_hcd *hcd, struct urb *urb, 2616 gfp_t mem_flags) 2617 { 2618 struct musb *musb = hcd_to_musb(hcd); 2619 int ret; 2620 2621 /* 2622 * The DMA engine in RTL1.8 and above cannot handle 2623 * DMA addresses that are not aligned to a 4 byte boundary. 2624 * For such engine implemented (un)map_urb_for_dma hooks. 2625 * Do not use these hooks for RTL<1.8 2626 */ 2627 if (musb->hwvers < MUSB_HWVERS_1800) 2628 return usb_hcd_map_urb_for_dma(hcd, urb, mem_flags); 2629 2630 ret = musb_alloc_temp_buffer(urb, mem_flags); 2631 if (ret) 2632 return ret; 2633 2634 ret = usb_hcd_map_urb_for_dma(hcd, urb, mem_flags); 2635 if (ret) 2636 musb_free_temp_buffer(urb); 2637 2638 return ret; 2639 } 2640 2641 static void musb_unmap_urb_for_dma(struct usb_hcd *hcd, struct urb *urb) 2642 { 2643 struct musb *musb = hcd_to_musb(hcd); 2644 2645 usb_hcd_unmap_urb_for_dma(hcd, urb); 2646 2647 /* Do not use this hook for RTL<1.8 (see description above) */ 2648 if (musb->hwvers < MUSB_HWVERS_1800) 2649 return; 2650 2651 musb_free_temp_buffer(urb); 2652 } 2653 #endif /* !CONFIG_MUSB_PIO_ONLY */ 2654 2655 static const struct hc_driver musb_hc_driver = { 2656 .description = "musb-hcd", 2657 .product_desc = "MUSB HDRC host driver", 2658 .hcd_priv_size = sizeof(struct musb *), 2659 .flags = HCD_USB2 | HCD_DMA | HCD_MEMORY, 2660 2661 /* not using irq handler or reset hooks from usbcore, since 2662 * those must be shared with peripheral code for OTG configs 2663 */ 2664 2665 .start = musb_h_start, 2666 .stop = musb_h_stop, 2667 2668 .get_frame_number = musb_h_get_frame_number, 2669 2670 .urb_enqueue = musb_urb_enqueue, 2671 .urb_dequeue = musb_urb_dequeue, 2672 .endpoint_disable = musb_h_disable, 2673 2674 #ifndef CONFIG_MUSB_PIO_ONLY 2675 .map_urb_for_dma = musb_map_urb_for_dma, 2676 .unmap_urb_for_dma = musb_unmap_urb_for_dma, 2677 #endif 2678 2679 .hub_status_data = musb_hub_status_data, 2680 .hub_control = musb_hub_control, 2681 .bus_suspend = musb_bus_suspend, 2682 .bus_resume = musb_bus_resume, 2683 /* .start_port_reset = NULL, */ 2684 /* .hub_irq_enable = NULL, */ 2685 }; 2686 2687 int musb_host_alloc(struct musb *musb) 2688 { 2689 struct device *dev = musb->controller; 2690 2691 /* usbcore sets dev->driver_data to hcd, and sometimes uses that... */ 2692 musb->hcd = usb_create_hcd(&musb_hc_driver, dev, dev_name(dev)); 2693 if (!musb->hcd) 2694 return -EINVAL; 2695 2696 *musb->hcd->hcd_priv = (unsigned long) musb; 2697 musb->hcd->self.uses_pio_for_control = 1; 2698 musb->hcd->uses_new_polling = 1; 2699 musb->hcd->has_tt = 1; 2700 2701 return 0; 2702 } 2703 2704 void musb_host_cleanup(struct musb *musb) 2705 { 2706 if (musb->port_mode == MUSB_PERIPHERAL) 2707 return; 2708 usb_remove_hcd(musb->hcd); 2709 } 2710 2711 void musb_host_free(struct musb *musb) 2712 { 2713 usb_put_hcd(musb->hcd); 2714 } 2715 2716 int musb_host_setup(struct musb *musb, int power_budget) 2717 { 2718 int ret; 2719 struct usb_hcd *hcd = musb->hcd; 2720 2721 if (musb->port_mode == MUSB_HOST) { 2722 MUSB_HST_MODE(musb); 2723 musb_set_state(musb, OTG_STATE_A_IDLE); 2724 } 2725 2726 if (musb->xceiv) { 2727 otg_set_host(musb->xceiv->otg, &hcd->self); 2728 musb->xceiv->otg->host = &hcd->self; 2729 } else { 2730 phy_set_mode(musb->phy, PHY_MODE_USB_HOST); 2731 } 2732 2733 /* don't support otg protocols */ 2734 hcd->self.otg_port = 0; 2735 hcd->power_budget = 2 * (power_budget ? : 250); 2736 hcd->skip_phy_initialization = 1; 2737 2738 ret = usb_add_hcd(hcd, 0, 0); 2739 if (ret < 0) 2740 return ret; 2741 2742 device_wakeup_enable(hcd->self.controller); 2743 return 0; 2744 } 2745 2746 void musb_host_resume_root_hub(struct musb *musb) 2747 { 2748 usb_hcd_resume_root_hub(musb->hcd); 2749 } 2750 2751 void musb_host_poke_root_hub(struct musb *musb) 2752 { 2753 MUSB_HST_MODE(musb); 2754 if (musb->hcd->status_urb) 2755 usb_hcd_poll_rh_status(musb->hcd); 2756 else 2757 usb_hcd_resume_root_hub(musb->hcd); 2758 } 2759