1 /* SPDX-License-Identifier: GPL-2.0 */ 2 3 /* 4 * xHCI host controller driver 5 * 6 * Copyright (C) 2008 Intel Corp. 7 * 8 * Author: Sarah Sharp 9 * Some code borrowed from the Linux EHCI driver. 10 */ 11 12 #ifndef __LINUX_XHCI_HCD_H 13 #define __LINUX_XHCI_HCD_H 14 15 #include <linux/usb.h> 16 #include <linux/timer.h> 17 #include <linux/kernel.h> 18 #include <linux/usb/hcd.h> 19 #include <linux/io-64-nonatomic-lo-hi.h> 20 21 /* Code sharing between pci-quirks and xhci hcd */ 22 #include "xhci-ext-caps.h" 23 #include "pci-quirks.h" 24 25 #include "xhci-port.h" 26 #include "xhci-caps.h" 27 28 /* max buffer size for trace and debug messages */ 29 #define XHCI_MSG_MAX 500 30 31 /* xHCI PCI Configuration Registers */ 32 #define XHCI_SBRN_OFFSET (0x60) 33 34 /* Max number of USB devices for any host controller - limit in section 6.1 */ 35 #define MAX_HC_SLOTS 256 36 /* Section 5.3.3 - MaxPorts */ 37 #define MAX_HC_PORTS 127 38 39 /* 40 * xHCI register interface. 41 * This corresponds to the eXtensible Host Controller Interface (xHCI) 42 * Revision 0.95 specification 43 */ 44 45 /** 46 * struct xhci_cap_regs - xHCI Host Controller Capability Registers. 47 * @hc_capbase: length of the capabilities register and HC version number 48 * @hcs_params1: HCSPARAMS1 - Structural Parameters 1 49 * @hcs_params2: HCSPARAMS2 - Structural Parameters 2 50 * @hcs_params3: HCSPARAMS3 - Structural Parameters 3 51 * @hcc_params: HCCPARAMS - Capability Parameters 52 * @db_off: DBOFF - Doorbell array offset 53 * @run_regs_off: RTSOFF - Runtime register space offset 54 * @hcc_params2: HCCPARAMS2 Capability Parameters 2, xhci 1.1 only 55 */ 56 struct xhci_cap_regs { 57 __le32 hc_capbase; 58 __le32 hcs_params1; 59 __le32 hcs_params2; 60 __le32 hcs_params3; 61 __le32 hcc_params; 62 __le32 db_off; 63 __le32 run_regs_off; 64 __le32 hcc_params2; /* xhci 1.1 */ 65 /* Reserved up to (CAPLENGTH - 0x1C) */ 66 }; 67 68 /* Number of registers per port */ 69 #define NUM_PORT_REGS 4 70 71 #define PORTSC 0 72 #define PORTPMSC 1 73 #define PORTLI 2 74 #define PORTHLPMC 3 75 76 /** 77 * struct xhci_op_regs - xHCI Host Controller Operational Registers. 78 * @command: USBCMD - xHC command register 79 * @status: USBSTS - xHC status register 80 * @page_size: This indicates the page size that the host controller 81 * supports. If bit n is set, the HC supports a page size 82 * of 2^(n+12), up to a 128MB page size. 83 * 4K is the minimum page size. 84 * @cmd_ring: CRP - 64-bit Command Ring Pointer 85 * @dcbaa_ptr: DCBAAP - 64-bit Device Context Base Address Array Pointer 86 * @config_reg: CONFIG - Configure Register 87 * @port_status_base: PORTSCn - base address for Port Status and Control 88 * Each port has a Port Status and Control register, 89 * followed by a Port Power Management Status and Control 90 * register, a Port Link Info register, and a reserved 91 * register. 92 * @port_power_base: PORTPMSCn - base address for 93 * Port Power Management Status and Control 94 * @port_link_base: PORTLIn - base address for Port Link Info (current 95 * Link PM state and control) for USB 2.1 and USB 3.0 96 * devices. 97 */ 98 struct xhci_op_regs { 99 __le32 command; 100 __le32 status; 101 __le32 page_size; 102 __le32 reserved1; 103 __le32 reserved2; 104 __le32 dev_notification; 105 __le64 cmd_ring; 106 /* rsvd: offset 0x20-2F */ 107 __le32 reserved3[4]; 108 __le64 dcbaa_ptr; 109 __le32 config_reg; 110 /* rsvd: offset 0x3C-3FF */ 111 __le32 reserved4[241]; 112 /* port 1 registers, which serve as a base address for other ports */ 113 __le32 port_status_base; 114 __le32 port_power_base; 115 __le32 port_link_base; 116 __le32 reserved5; 117 /* registers for ports 2-255 */ 118 __le32 reserved6[NUM_PORT_REGS*254]; 119 }; 120 121 /* USBCMD - USB command - command bitmasks */ 122 /* start/stop HC execution - do not write unless HC is halted*/ 123 #define CMD_RUN XHCI_CMD_RUN 124 /* Reset HC - resets internal HC state machine and all registers (except 125 * PCI config regs). HC does NOT drive a USB reset on the downstream ports. 126 * The xHCI driver must reinitialize the xHC after setting this bit. 127 */ 128 #define CMD_RESET (1 << 1) 129 /* Event Interrupt Enable - a '1' allows interrupts from the host controller */ 130 #define CMD_EIE XHCI_CMD_EIE 131 /* Host System Error Interrupt Enable - get out-of-band signal for HC errors */ 132 #define CMD_HSEIE XHCI_CMD_HSEIE 133 /* bits 4:6 are reserved (and should be preserved on writes). */ 134 /* light reset (port status stays unchanged) - reset completed when this is 0 */ 135 #define CMD_LRESET (1 << 7) 136 /* host controller save/restore state. */ 137 #define CMD_CSS (1 << 8) 138 #define CMD_CRS (1 << 9) 139 /* Enable Wrap Event - '1' means xHC generates an event when MFINDEX wraps. */ 140 #define CMD_EWE XHCI_CMD_EWE 141 /* MFINDEX power management - '1' means xHC can stop MFINDEX counter if all root 142 * hubs are in U3 (selective suspend), disconnect, disabled, or powered-off. 143 * '0' means the xHC can power it off if all ports are in the disconnect, 144 * disabled, or powered-off state. 145 */ 146 #define CMD_PM_INDEX (1 << 11) 147 /* bit 14 Extended TBC Enable, changes Isoc TRB fields to support larger TBC */ 148 #define CMD_ETE (1 << 14) 149 /* bits 15:31 are reserved (and should be preserved on writes). */ 150 151 #define XHCI_RESET_LONG_USEC (10 * 1000 * 1000) 152 #define XHCI_RESET_SHORT_USEC (250 * 1000) 153 154 /* IMAN - Interrupt Management Register */ 155 #define IMAN_IE (1 << 1) 156 #define IMAN_IP (1 << 0) 157 158 /* USBSTS - USB status - status bitmasks */ 159 /* HC not running - set to 1 when run/stop bit is cleared. */ 160 #define STS_HALT XHCI_STS_HALT 161 /* serious error, e.g. PCI parity error. The HC will clear the run/stop bit. */ 162 #define STS_FATAL (1 << 2) 163 /* event interrupt - clear this prior to clearing any IP flags in IR set*/ 164 #define STS_EINT (1 << 3) 165 /* port change detect */ 166 #define STS_PORT (1 << 4) 167 /* bits 5:7 reserved and zeroed */ 168 /* save state status - '1' means xHC is saving state */ 169 #define STS_SAVE (1 << 8) 170 /* restore state status - '1' means xHC is restoring state */ 171 #define STS_RESTORE (1 << 9) 172 /* true: save or restore error */ 173 #define STS_SRE (1 << 10) 174 /* true: Controller Not Ready to accept doorbell or op reg writes after reset */ 175 #define STS_CNR XHCI_STS_CNR 176 /* true: internal Host Controller Error - SW needs to reset and reinitialize */ 177 #define STS_HCE (1 << 12) 178 /* bits 13:31 reserved and should be preserved */ 179 180 /* 181 * DNCTRL - Device Notification Control Register - dev_notification bitmasks 182 * Generate a device notification event when the HC sees a transaction with a 183 * notification type that matches a bit set in this bit field. 184 */ 185 #define DEV_NOTE_MASK (0xffff) 186 #define ENABLE_DEV_NOTE(x) (1 << (x)) 187 /* Most of the device notification types should only be used for debug. 188 * SW does need to pay attention to function wake notifications. 189 */ 190 #define DEV_NOTE_FWAKE ENABLE_DEV_NOTE(1) 191 192 /* CRCR - Command Ring Control Register - cmd_ring bitmasks */ 193 /* bit 0 is the command ring cycle state */ 194 /* stop ring operation after completion of the currently executing command */ 195 #define CMD_RING_PAUSE (1 << 1) 196 /* stop ring immediately - abort the currently executing command */ 197 #define CMD_RING_ABORT (1 << 2) 198 /* true: command ring is running */ 199 #define CMD_RING_RUNNING (1 << 3) 200 /* bits 4:5 reserved and should be preserved */ 201 /* Command Ring pointer - bit mask for the lower 32 bits. */ 202 #define CMD_RING_RSVD_BITS (0x3f) 203 204 /* CONFIG - Configure Register - config_reg bitmasks */ 205 /* bits 0:7 - maximum number of device slots enabled (NumSlotsEn) */ 206 #define MAX_DEVS(p) ((p) & 0xff) 207 /* bit 8: U3 Entry Enabled, assert PLC when root port enters U3, xhci 1.1 */ 208 #define CONFIG_U3E (1 << 8) 209 /* bit 9: Configuration Information Enable, xhci 1.1 */ 210 #define CONFIG_CIE (1 << 9) 211 /* bits 10:31 - reserved and should be preserved */ 212 213 /** 214 * struct xhci_intr_reg - Interrupt Register Set 215 * @irq_pending: IMAN - Interrupt Management Register. Used to enable 216 * interrupts and check for pending interrupts. 217 * @irq_control: IMOD - Interrupt Moderation Register. 218 * Used to throttle interrupts. 219 * @erst_size: Number of segments in the Event Ring Segment Table (ERST). 220 * @erst_base: ERST base address. 221 * @erst_dequeue: Event ring dequeue pointer. 222 * 223 * Each interrupter (defined by a MSI-X vector) has an event ring and an Event 224 * Ring Segment Table (ERST) associated with it. The event ring is comprised of 225 * multiple segments of the same size. The HC places events on the ring and 226 * "updates the Cycle bit in the TRBs to indicate to software the current 227 * position of the Enqueue Pointer." The HCD (Linux) processes those events and 228 * updates the dequeue pointer. 229 */ 230 struct xhci_intr_reg { 231 __le32 irq_pending; 232 __le32 irq_control; 233 __le32 erst_size; 234 __le32 rsvd; 235 __le64 erst_base; 236 __le64 erst_dequeue; 237 }; 238 239 /* irq_pending bitmasks */ 240 #define ER_IRQ_PENDING(p) ((p) & 0x1) 241 /* bits 2:31 need to be preserved */ 242 /* THIS IS BUGGY - FIXME - IP IS WRITE 1 TO CLEAR */ 243 #define ER_IRQ_CLEAR(p) ((p) & 0xfffffffe) 244 #define ER_IRQ_ENABLE(p) ((ER_IRQ_CLEAR(p)) | 0x2) 245 #define ER_IRQ_DISABLE(p) ((ER_IRQ_CLEAR(p)) & ~(0x2)) 246 247 /* irq_control bitmasks */ 248 /* Minimum interval between interrupts (in 250ns intervals). The interval 249 * between interrupts will be longer if there are no events on the event ring. 250 * Default is 4000 (1 ms). 251 */ 252 #define ER_IRQ_INTERVAL_MASK (0xffff) 253 /* Counter used to count down the time to the next interrupt - HW use only */ 254 #define ER_IRQ_COUNTER_MASK (0xffff << 16) 255 256 /* erst_size bitmasks */ 257 /* Preserve bits 16:31 of erst_size */ 258 #define ERST_SIZE_MASK (0xffff << 16) 259 260 /* erst_base bitmasks */ 261 #define ERST_BASE_RSVDP (GENMASK_ULL(5, 0)) 262 263 /* erst_dequeue bitmasks */ 264 /* Dequeue ERST Segment Index (DESI) - Segment number (or alias) 265 * where the current dequeue pointer lies. This is an optional HW hint. 266 */ 267 #define ERST_DESI_MASK (0x7) 268 /* Event Handler Busy (EHB) - is the event ring scheduled to be serviced by 269 * a work queue (or delayed service routine)? 270 */ 271 #define ERST_EHB (1 << 3) 272 #define ERST_PTR_MASK (GENMASK_ULL(63, 4)) 273 274 /** 275 * struct xhci_run_regs 276 * @microframe_index: 277 * MFINDEX - current microframe number 278 * 279 * Section 5.5 Host Controller Runtime Registers: 280 * "Software should read and write these registers using only Dword (32 bit) 281 * or larger accesses" 282 */ 283 struct xhci_run_regs { 284 __le32 microframe_index; 285 __le32 rsvd[7]; 286 struct xhci_intr_reg ir_set[128]; 287 }; 288 289 /** 290 * struct doorbell_array 291 * 292 * Bits 0 - 7: Endpoint target 293 * Bits 8 - 15: RsvdZ 294 * Bits 16 - 31: Stream ID 295 * 296 * Section 5.6 297 */ 298 struct xhci_doorbell_array { 299 __le32 doorbell[256]; 300 }; 301 302 #define DB_VALUE(ep, stream) ((((ep) + 1) & 0xff) | ((stream) << 16)) 303 #define DB_VALUE_HOST 0x00000000 304 305 #define PLT_MASK (0x03 << 6) 306 #define PLT_SYM (0x00 << 6) 307 #define PLT_ASYM_RX (0x02 << 6) 308 #define PLT_ASYM_TX (0x03 << 6) 309 310 /** 311 * struct xhci_container_ctx 312 * @type: Type of context. Used to calculated offsets to contained contexts. 313 * @size: Size of the context data 314 * @bytes: The raw context data given to HW 315 * @dma: dma address of the bytes 316 * 317 * Represents either a Device or Input context. Holds a pointer to the raw 318 * memory used for the context (bytes) and dma address of it (dma). 319 */ 320 struct xhci_container_ctx { 321 unsigned type; 322 #define XHCI_CTX_TYPE_DEVICE 0x1 323 #define XHCI_CTX_TYPE_INPUT 0x2 324 325 int size; 326 327 u8 *bytes; 328 dma_addr_t dma; 329 }; 330 331 /** 332 * struct xhci_slot_ctx 333 * @dev_info: Route string, device speed, hub info, and last valid endpoint 334 * @dev_info2: Max exit latency for device number, root hub port number 335 * @tt_info: tt_info is used to construct split transaction tokens 336 * @dev_state: slot state and device address 337 * 338 * Slot Context - section 6.2.1.1. This assumes the HC uses 32-byte context 339 * structures. If the HC uses 64-byte contexts, there is an additional 32 bytes 340 * reserved at the end of the slot context for HC internal use. 341 */ 342 struct xhci_slot_ctx { 343 __le32 dev_info; 344 __le32 dev_info2; 345 __le32 tt_info; 346 __le32 dev_state; 347 /* offset 0x10 to 0x1f reserved for HC internal use */ 348 __le32 reserved[4]; 349 }; 350 351 /* dev_info bitmasks */ 352 /* Route String - 0:19 */ 353 #define ROUTE_STRING_MASK (0xfffff) 354 /* Device speed - values defined by PORTSC Device Speed field - 20:23 */ 355 #define DEV_SPEED (0xf << 20) 356 #define GET_DEV_SPEED(n) (((n) & DEV_SPEED) >> 20) 357 /* bit 24 reserved */ 358 /* Is this LS/FS device connected through a HS hub? - bit 25 */ 359 #define DEV_MTT (0x1 << 25) 360 /* Set if the device is a hub - bit 26 */ 361 #define DEV_HUB (0x1 << 26) 362 /* Index of the last valid endpoint context in this device context - 27:31 */ 363 #define LAST_CTX_MASK (0x1f << 27) 364 #define LAST_CTX(p) ((p) << 27) 365 #define LAST_CTX_TO_EP_NUM(p) (((p) >> 27) - 1) 366 #define SLOT_FLAG (1 << 0) 367 #define EP0_FLAG (1 << 1) 368 369 /* dev_info2 bitmasks */ 370 /* Max Exit Latency (ms) - worst case time to wake up all links in dev path */ 371 #define MAX_EXIT (0xffff) 372 /* Root hub port number that is needed to access the USB device */ 373 #define ROOT_HUB_PORT(p) (((p) & 0xff) << 16) 374 #define DEVINFO_TO_ROOT_HUB_PORT(p) (((p) >> 16) & 0xff) 375 /* Maximum number of ports under a hub device */ 376 #define XHCI_MAX_PORTS(p) (((p) & 0xff) << 24) 377 #define DEVINFO_TO_MAX_PORTS(p) (((p) & (0xff << 24)) >> 24) 378 379 /* tt_info bitmasks */ 380 /* 381 * TT Hub Slot ID - for low or full speed devices attached to a high-speed hub 382 * The Slot ID of the hub that isolates the high speed signaling from 383 * this low or full-speed device. '0' if attached to root hub port. 384 */ 385 #define TT_SLOT (0xff) 386 /* 387 * The number of the downstream facing port of the high-speed hub 388 * '0' if the device is not low or full speed. 389 */ 390 #define TT_PORT (0xff << 8) 391 #define TT_THINK_TIME(p) (((p) & 0x3) << 16) 392 #define GET_TT_THINK_TIME(p) (((p) & (0x3 << 16)) >> 16) 393 394 /* dev_state bitmasks */ 395 /* USB device address - assigned by the HC */ 396 #define DEV_ADDR_MASK (0xff) 397 /* bits 8:26 reserved */ 398 /* Slot state */ 399 #define SLOT_STATE (0x1f << 27) 400 #define GET_SLOT_STATE(p) (((p) & (0x1f << 27)) >> 27) 401 402 #define SLOT_STATE_DISABLED 0 403 #define SLOT_STATE_ENABLED SLOT_STATE_DISABLED 404 #define SLOT_STATE_DEFAULT 1 405 #define SLOT_STATE_ADDRESSED 2 406 #define SLOT_STATE_CONFIGURED 3 407 408 /** 409 * struct xhci_ep_ctx 410 * @ep_info: endpoint state, streams, mult, and interval information. 411 * @ep_info2: information on endpoint type, max packet size, max burst size, 412 * error count, and whether the HC will force an event for all 413 * transactions. 414 * @deq: 64-bit ring dequeue pointer address. If the endpoint only 415 * defines one stream, this points to the endpoint transfer ring. 416 * Otherwise, it points to a stream context array, which has a 417 * ring pointer for each flow. 418 * @tx_info: 419 * Average TRB lengths for the endpoint ring and 420 * max payload within an Endpoint Service Interval Time (ESIT). 421 * 422 * Endpoint Context - section 6.2.1.2. This assumes the HC uses 32-byte context 423 * structures. If the HC uses 64-byte contexts, there is an additional 32 bytes 424 * reserved at the end of the endpoint context for HC internal use. 425 */ 426 struct xhci_ep_ctx { 427 __le32 ep_info; 428 __le32 ep_info2; 429 __le64 deq; 430 __le32 tx_info; 431 /* offset 0x14 - 0x1f reserved for HC internal use */ 432 __le32 reserved[3]; 433 }; 434 435 /* ep_info bitmasks */ 436 /* 437 * Endpoint State - bits 0:2 438 * 0 - disabled 439 * 1 - running 440 * 2 - halted due to halt condition - ok to manipulate endpoint ring 441 * 3 - stopped 442 * 4 - TRB error 443 * 5-7 - reserved 444 */ 445 #define EP_STATE_MASK (0x7) 446 #define EP_STATE_DISABLED 0 447 #define EP_STATE_RUNNING 1 448 #define EP_STATE_HALTED 2 449 #define EP_STATE_STOPPED 3 450 #define EP_STATE_ERROR 4 451 #define GET_EP_CTX_STATE(ctx) (le32_to_cpu((ctx)->ep_info) & EP_STATE_MASK) 452 453 /* Mult - Max number of burtst within an interval, in EP companion desc. */ 454 #define EP_MULT(p) (((p) & 0x3) << 8) 455 #define CTX_TO_EP_MULT(p) (((p) >> 8) & 0x3) 456 /* bits 10:14 are Max Primary Streams */ 457 /* bit 15 is Linear Stream Array */ 458 /* Interval - period between requests to an endpoint - 125u increments. */ 459 #define EP_INTERVAL(p) (((p) & 0xff) << 16) 460 #define EP_INTERVAL_TO_UFRAMES(p) (1 << (((p) >> 16) & 0xff)) 461 #define CTX_TO_EP_INTERVAL(p) (((p) >> 16) & 0xff) 462 #define EP_MAXPSTREAMS_MASK (0x1f << 10) 463 #define EP_MAXPSTREAMS(p) (((p) << 10) & EP_MAXPSTREAMS_MASK) 464 #define CTX_TO_EP_MAXPSTREAMS(p) (((p) & EP_MAXPSTREAMS_MASK) >> 10) 465 /* Endpoint is set up with a Linear Stream Array (vs. Secondary Stream Array) */ 466 #define EP_HAS_LSA (1 << 15) 467 /* hosts with LEC=1 use bits 31:24 as ESIT high bits. */ 468 #define CTX_TO_MAX_ESIT_PAYLOAD_HI(p) (((p) >> 24) & 0xff) 469 470 /* ep_info2 bitmasks */ 471 /* 472 * Force Event - generate transfer events for all TRBs for this endpoint 473 * This will tell the HC to ignore the IOC and ISP flags (for debugging only). 474 */ 475 #define FORCE_EVENT (0x1) 476 #define ERROR_COUNT(p) (((p) & 0x3) << 1) 477 #define CTX_TO_EP_TYPE(p) (((p) >> 3) & 0x7) 478 #define EP_TYPE(p) ((p) << 3) 479 #define ISOC_OUT_EP 1 480 #define BULK_OUT_EP 2 481 #define INT_OUT_EP 3 482 #define CTRL_EP 4 483 #define ISOC_IN_EP 5 484 #define BULK_IN_EP 6 485 #define INT_IN_EP 7 486 /* bit 6 reserved */ 487 /* bit 7 is Host Initiate Disable - for disabling stream selection */ 488 #define MAX_BURST(p) (((p)&0xff) << 8) 489 #define CTX_TO_MAX_BURST(p) (((p) >> 8) & 0xff) 490 #define MAX_PACKET(p) (((p)&0xffff) << 16) 491 #define MAX_PACKET_MASK (0xffff << 16) 492 #define MAX_PACKET_DECODED(p) (((p) >> 16) & 0xffff) 493 494 /* tx_info bitmasks */ 495 #define EP_AVG_TRB_LENGTH(p) ((p) & 0xffff) 496 #define EP_MAX_ESIT_PAYLOAD_LO(p) (((p) & 0xffff) << 16) 497 #define EP_MAX_ESIT_PAYLOAD_HI(p) ((((p) >> 16) & 0xff) << 24) 498 #define CTX_TO_MAX_ESIT_PAYLOAD(p) (((p) >> 16) & 0xffff) 499 500 /* deq bitmasks */ 501 #define EP_CTX_CYCLE_MASK (1 << 0) 502 #define SCTX_DEQ_MASK (~0xfL) 503 504 505 /** 506 * struct xhci_input_control_context 507 * Input control context; see section 6.2.5. 508 * 509 * @drop_context: set the bit of the endpoint context you want to disable 510 * @add_context: set the bit of the endpoint context you want to enable 511 */ 512 struct xhci_input_control_ctx { 513 __le32 drop_flags; 514 __le32 add_flags; 515 __le32 rsvd2[6]; 516 }; 517 518 #define EP_IS_ADDED(ctrl_ctx, i) \ 519 (le32_to_cpu(ctrl_ctx->add_flags) & (1 << (i + 1))) 520 #define EP_IS_DROPPED(ctrl_ctx, i) \ 521 (le32_to_cpu(ctrl_ctx->drop_flags) & (1 << (i + 1))) 522 523 /* Represents everything that is needed to issue a command on the command ring. 524 * It's useful to pre-allocate these for commands that cannot fail due to 525 * out-of-memory errors, like freeing streams. 526 */ 527 struct xhci_command { 528 /* Input context for changing device state */ 529 struct xhci_container_ctx *in_ctx; 530 u32 status; 531 int slot_id; 532 /* If completion is null, no one is waiting on this command 533 * and the structure can be freed after the command completes. 534 */ 535 struct completion *completion; 536 union xhci_trb *command_trb; 537 struct list_head cmd_list; 538 /* xHCI command response timeout in milliseconds */ 539 unsigned int timeout_ms; 540 }; 541 542 /* drop context bitmasks */ 543 #define DROP_EP(x) (0x1 << x) 544 /* add context bitmasks */ 545 #define ADD_EP(x) (0x1 << x) 546 547 struct xhci_stream_ctx { 548 /* 64-bit stream ring address, cycle state, and stream type */ 549 __le64 stream_ring; 550 /* offset 0x14 - 0x1f reserved for HC internal use */ 551 __le32 reserved[2]; 552 }; 553 554 /* Stream Context Types (section 6.4.1) - bits 3:1 of stream ctx deq ptr */ 555 #define SCT_FOR_CTX(p) (((p) & 0x7) << 1) 556 /* Secondary stream array type, dequeue pointer is to a transfer ring */ 557 #define SCT_SEC_TR 0 558 /* Primary stream array type, dequeue pointer is to a transfer ring */ 559 #define SCT_PRI_TR 1 560 /* Dequeue pointer is for a secondary stream array (SSA) with 8 entries */ 561 #define SCT_SSA_8 2 562 #define SCT_SSA_16 3 563 #define SCT_SSA_32 4 564 #define SCT_SSA_64 5 565 #define SCT_SSA_128 6 566 #define SCT_SSA_256 7 567 568 /* Assume no secondary streams for now */ 569 struct xhci_stream_info { 570 struct xhci_ring **stream_rings; 571 /* Number of streams, including stream 0 (which drivers can't use) */ 572 unsigned int num_streams; 573 /* The stream context array may be bigger than 574 * the number of streams the driver asked for 575 */ 576 struct xhci_stream_ctx *stream_ctx_array; 577 unsigned int num_stream_ctxs; 578 dma_addr_t ctx_array_dma; 579 /* For mapping physical TRB addresses to segments in stream rings */ 580 struct radix_tree_root trb_address_map; 581 struct xhci_command *free_streams_command; 582 }; 583 584 #define SMALL_STREAM_ARRAY_SIZE 256 585 #define MEDIUM_STREAM_ARRAY_SIZE 1024 586 587 /* Some Intel xHCI host controllers need software to keep track of the bus 588 * bandwidth. Keep track of endpoint info here. Each root port is allocated 589 * the full bus bandwidth. We must also treat TTs (including each port under a 590 * multi-TT hub) as a separate bandwidth domain. The direct memory interface 591 * (DMI) also limits the total bandwidth (across all domains) that can be used. 592 */ 593 struct xhci_bw_info { 594 /* ep_interval is zero-based */ 595 unsigned int ep_interval; 596 /* mult and num_packets are one-based */ 597 unsigned int mult; 598 unsigned int num_packets; 599 unsigned int max_packet_size; 600 unsigned int max_esit_payload; 601 unsigned int type; 602 }; 603 604 /* "Block" sizes in bytes the hardware uses for different device speeds. 605 * The logic in this part of the hardware limits the number of bits the hardware 606 * can use, so must represent bandwidth in a less precise manner to mimic what 607 * the scheduler hardware computes. 608 */ 609 #define FS_BLOCK 1 610 #define HS_BLOCK 4 611 #define SS_BLOCK 16 612 #define DMI_BLOCK 32 613 614 /* Each device speed has a protocol overhead (CRC, bit stuffing, etc) associated 615 * with each byte transferred. SuperSpeed devices have an initial overhead to 616 * set up bursts. These are in blocks, see above. LS overhead has already been 617 * translated into FS blocks. 618 */ 619 #define DMI_OVERHEAD 8 620 #define DMI_OVERHEAD_BURST 4 621 #define SS_OVERHEAD 8 622 #define SS_OVERHEAD_BURST 32 623 #define HS_OVERHEAD 26 624 #define FS_OVERHEAD 20 625 #define LS_OVERHEAD 128 626 /* The TTs need to claim roughly twice as much bandwidth (94 bytes per 627 * microframe ~= 24Mbps) of the HS bus as the devices can actually use because 628 * of overhead associated with split transfers crossing microframe boundaries. 629 * 31 blocks is pure protocol overhead. 630 */ 631 #define TT_HS_OVERHEAD (31 + 94) 632 #define TT_DMI_OVERHEAD (25 + 12) 633 634 /* Bandwidth limits in blocks */ 635 #define FS_BW_LIMIT 1285 636 #define TT_BW_LIMIT 1320 637 #define HS_BW_LIMIT 1607 638 #define SS_BW_LIMIT_IN 3906 639 #define DMI_BW_LIMIT_IN 3906 640 #define SS_BW_LIMIT_OUT 3906 641 #define DMI_BW_LIMIT_OUT 3906 642 643 /* Percentage of bus bandwidth reserved for non-periodic transfers */ 644 #define FS_BW_RESERVED 10 645 #define HS_BW_RESERVED 20 646 #define SS_BW_RESERVED 10 647 648 struct xhci_virt_ep { 649 struct xhci_virt_device *vdev; /* parent */ 650 unsigned int ep_index; 651 struct xhci_ring *ring; 652 /* Related to endpoints that are configured to use stream IDs only */ 653 struct xhci_stream_info *stream_info; 654 /* Temporary storage in case the configure endpoint command fails and we 655 * have to restore the device state to the previous state 656 */ 657 struct xhci_ring *new_ring; 658 unsigned int err_count; 659 unsigned int ep_state; 660 #define SET_DEQ_PENDING (1 << 0) 661 #define EP_HALTED (1 << 1) /* For stall handling */ 662 #define EP_STOP_CMD_PENDING (1 << 2) /* For URB cancellation */ 663 /* Transitioning the endpoint to using streams, don't enqueue URBs */ 664 #define EP_GETTING_STREAMS (1 << 3) 665 #define EP_HAS_STREAMS (1 << 4) 666 /* Transitioning the endpoint to not using streams, don't enqueue URBs */ 667 #define EP_GETTING_NO_STREAMS (1 << 5) 668 #define EP_HARD_CLEAR_TOGGLE (1 << 6) 669 #define EP_SOFT_CLEAR_TOGGLE (1 << 7) 670 /* usb_hub_clear_tt_buffer is in progress */ 671 #define EP_CLEARING_TT (1 << 8) 672 /* ---- Related to URB cancellation ---- */ 673 struct list_head cancelled_td_list; 674 struct xhci_hcd *xhci; 675 /* Dequeue pointer and dequeue segment for a submitted Set TR Dequeue 676 * command. We'll need to update the ring's dequeue segment and dequeue 677 * pointer after the command completes. 678 */ 679 struct xhci_segment *queued_deq_seg; 680 union xhci_trb *queued_deq_ptr; 681 /* 682 * Sometimes the xHC can not process isochronous endpoint ring quickly 683 * enough, and it will miss some isoc tds on the ring and generate 684 * a Missed Service Error Event. 685 * Set skip flag when receive a Missed Service Error Event and 686 * process the missed tds on the endpoint ring. 687 */ 688 bool skip; 689 /* Bandwidth checking storage */ 690 struct xhci_bw_info bw_info; 691 struct list_head bw_endpoint_list; 692 /* Isoch Frame ID checking storage */ 693 int next_frame_id; 694 /* Use new Isoch TRB layout needed for extended TBC support */ 695 bool use_extended_tbc; 696 }; 697 698 enum xhci_overhead_type { 699 LS_OVERHEAD_TYPE = 0, 700 FS_OVERHEAD_TYPE, 701 HS_OVERHEAD_TYPE, 702 }; 703 704 struct xhci_interval_bw { 705 unsigned int num_packets; 706 /* Sorted by max packet size. 707 * Head of the list is the greatest max packet size. 708 */ 709 struct list_head endpoints; 710 /* How many endpoints of each speed are present. */ 711 unsigned int overhead[3]; 712 }; 713 714 #define XHCI_MAX_INTERVAL 16 715 716 struct xhci_interval_bw_table { 717 unsigned int interval0_esit_payload; 718 struct xhci_interval_bw interval_bw[XHCI_MAX_INTERVAL]; 719 /* Includes reserved bandwidth for async endpoints */ 720 unsigned int bw_used; 721 unsigned int ss_bw_in; 722 unsigned int ss_bw_out; 723 }; 724 725 #define EP_CTX_PER_DEV 31 726 727 struct xhci_virt_device { 728 int slot_id; 729 struct usb_device *udev; 730 /* 731 * Commands to the hardware are passed an "input context" that 732 * tells the hardware what to change in its data structures. 733 * The hardware will return changes in an "output context" that 734 * software must allocate for the hardware. We need to keep 735 * track of input and output contexts separately because 736 * these commands might fail and we don't trust the hardware. 737 */ 738 struct xhci_container_ctx *out_ctx; 739 /* Used for addressing devices and configuration changes */ 740 struct xhci_container_ctx *in_ctx; 741 struct xhci_virt_ep eps[EP_CTX_PER_DEV]; 742 struct xhci_port *rhub_port; 743 struct xhci_interval_bw_table *bw_table; 744 struct xhci_tt_bw_info *tt_info; 745 /* 746 * flags for state tracking based on events and issued commands. 747 * Software can not rely on states from output contexts because of 748 * latency between events and xHC updating output context values. 749 * See xhci 1.1 section 4.8.3 for more details 750 */ 751 unsigned long flags; 752 #define VDEV_PORT_ERROR BIT(0) /* Port error, link inactive */ 753 754 /* The current max exit latency for the enabled USB3 link states. */ 755 u16 current_mel; 756 /* Used for the debugfs interfaces. */ 757 void *debugfs_private; 758 }; 759 760 /* 761 * For each roothub, keep track of the bandwidth information for each periodic 762 * interval. 763 * 764 * If a high speed hub is attached to the roothub, each TT associated with that 765 * hub is a separate bandwidth domain. The interval information for the 766 * endpoints on the devices under that TT will appear in the TT structure. 767 */ 768 struct xhci_root_port_bw_info { 769 struct list_head tts; 770 unsigned int num_active_tts; 771 struct xhci_interval_bw_table bw_table; 772 }; 773 774 struct xhci_tt_bw_info { 775 struct list_head tt_list; 776 int slot_id; 777 int ttport; 778 struct xhci_interval_bw_table bw_table; 779 int active_eps; 780 }; 781 782 783 /** 784 * struct xhci_device_context_array 785 * @dev_context_ptr array of 64-bit DMA addresses for device contexts 786 */ 787 struct xhci_device_context_array { 788 /* 64-bit device addresses; we only write 32-bit addresses */ 789 __le64 dev_context_ptrs[MAX_HC_SLOTS]; 790 /* private xHCD pointers */ 791 dma_addr_t dma; 792 }; 793 /* TODO: write function to set the 64-bit device DMA address */ 794 /* 795 * TODO: change this to be dynamically sized at HC mem init time since the HC 796 * might not be able to handle the maximum number of devices possible. 797 */ 798 799 800 struct xhci_transfer_event { 801 /* 64-bit buffer address, or immediate data */ 802 __le64 buffer; 803 __le32 transfer_len; 804 /* This field is interpreted differently based on the type of TRB */ 805 __le32 flags; 806 }; 807 808 /* Transfer event TRB length bit mask */ 809 /* bits 0:23 */ 810 #define EVENT_TRB_LEN(p) ((p) & 0xffffff) 811 812 /** Transfer Event bit fields **/ 813 #define TRB_TO_EP_ID(p) (((p) >> 16) & 0x1f) 814 815 /* Completion Code - only applicable for some types of TRBs */ 816 #define COMP_CODE_MASK (0xff << 24) 817 #define GET_COMP_CODE(p) (((p) & COMP_CODE_MASK) >> 24) 818 #define COMP_INVALID 0 819 #define COMP_SUCCESS 1 820 #define COMP_DATA_BUFFER_ERROR 2 821 #define COMP_BABBLE_DETECTED_ERROR 3 822 #define COMP_USB_TRANSACTION_ERROR 4 823 #define COMP_TRB_ERROR 5 824 #define COMP_STALL_ERROR 6 825 #define COMP_RESOURCE_ERROR 7 826 #define COMP_BANDWIDTH_ERROR 8 827 #define COMP_NO_SLOTS_AVAILABLE_ERROR 9 828 #define COMP_INVALID_STREAM_TYPE_ERROR 10 829 #define COMP_SLOT_NOT_ENABLED_ERROR 11 830 #define COMP_ENDPOINT_NOT_ENABLED_ERROR 12 831 #define COMP_SHORT_PACKET 13 832 #define COMP_RING_UNDERRUN 14 833 #define COMP_RING_OVERRUN 15 834 #define COMP_VF_EVENT_RING_FULL_ERROR 16 835 #define COMP_PARAMETER_ERROR 17 836 #define COMP_BANDWIDTH_OVERRUN_ERROR 18 837 #define COMP_CONTEXT_STATE_ERROR 19 838 #define COMP_NO_PING_RESPONSE_ERROR 20 839 #define COMP_EVENT_RING_FULL_ERROR 21 840 #define COMP_INCOMPATIBLE_DEVICE_ERROR 22 841 #define COMP_MISSED_SERVICE_ERROR 23 842 #define COMP_COMMAND_RING_STOPPED 24 843 #define COMP_COMMAND_ABORTED 25 844 #define COMP_STOPPED 26 845 #define COMP_STOPPED_LENGTH_INVALID 27 846 #define COMP_STOPPED_SHORT_PACKET 28 847 #define COMP_MAX_EXIT_LATENCY_TOO_LARGE_ERROR 29 848 #define COMP_ISOCH_BUFFER_OVERRUN 31 849 #define COMP_EVENT_LOST_ERROR 32 850 #define COMP_UNDEFINED_ERROR 33 851 #define COMP_INVALID_STREAM_ID_ERROR 34 852 #define COMP_SECONDARY_BANDWIDTH_ERROR 35 853 #define COMP_SPLIT_TRANSACTION_ERROR 36 854 855 static inline const char *xhci_trb_comp_code_string(u8 status) 856 { 857 switch (status) { 858 case COMP_INVALID: 859 return "Invalid"; 860 case COMP_SUCCESS: 861 return "Success"; 862 case COMP_DATA_BUFFER_ERROR: 863 return "Data Buffer Error"; 864 case COMP_BABBLE_DETECTED_ERROR: 865 return "Babble Detected"; 866 case COMP_USB_TRANSACTION_ERROR: 867 return "USB Transaction Error"; 868 case COMP_TRB_ERROR: 869 return "TRB Error"; 870 case COMP_STALL_ERROR: 871 return "Stall Error"; 872 case COMP_RESOURCE_ERROR: 873 return "Resource Error"; 874 case COMP_BANDWIDTH_ERROR: 875 return "Bandwidth Error"; 876 case COMP_NO_SLOTS_AVAILABLE_ERROR: 877 return "No Slots Available Error"; 878 case COMP_INVALID_STREAM_TYPE_ERROR: 879 return "Invalid Stream Type Error"; 880 case COMP_SLOT_NOT_ENABLED_ERROR: 881 return "Slot Not Enabled Error"; 882 case COMP_ENDPOINT_NOT_ENABLED_ERROR: 883 return "Endpoint Not Enabled Error"; 884 case COMP_SHORT_PACKET: 885 return "Short Packet"; 886 case COMP_RING_UNDERRUN: 887 return "Ring Underrun"; 888 case COMP_RING_OVERRUN: 889 return "Ring Overrun"; 890 case COMP_VF_EVENT_RING_FULL_ERROR: 891 return "VF Event Ring Full Error"; 892 case COMP_PARAMETER_ERROR: 893 return "Parameter Error"; 894 case COMP_BANDWIDTH_OVERRUN_ERROR: 895 return "Bandwidth Overrun Error"; 896 case COMP_CONTEXT_STATE_ERROR: 897 return "Context State Error"; 898 case COMP_NO_PING_RESPONSE_ERROR: 899 return "No Ping Response Error"; 900 case COMP_EVENT_RING_FULL_ERROR: 901 return "Event Ring Full Error"; 902 case COMP_INCOMPATIBLE_DEVICE_ERROR: 903 return "Incompatible Device Error"; 904 case COMP_MISSED_SERVICE_ERROR: 905 return "Missed Service Error"; 906 case COMP_COMMAND_RING_STOPPED: 907 return "Command Ring Stopped"; 908 case COMP_COMMAND_ABORTED: 909 return "Command Aborted"; 910 case COMP_STOPPED: 911 return "Stopped"; 912 case COMP_STOPPED_LENGTH_INVALID: 913 return "Stopped - Length Invalid"; 914 case COMP_STOPPED_SHORT_PACKET: 915 return "Stopped - Short Packet"; 916 case COMP_MAX_EXIT_LATENCY_TOO_LARGE_ERROR: 917 return "Max Exit Latency Too Large Error"; 918 case COMP_ISOCH_BUFFER_OVERRUN: 919 return "Isoch Buffer Overrun"; 920 case COMP_EVENT_LOST_ERROR: 921 return "Event Lost Error"; 922 case COMP_UNDEFINED_ERROR: 923 return "Undefined Error"; 924 case COMP_INVALID_STREAM_ID_ERROR: 925 return "Invalid Stream ID Error"; 926 case COMP_SECONDARY_BANDWIDTH_ERROR: 927 return "Secondary Bandwidth Error"; 928 case COMP_SPLIT_TRANSACTION_ERROR: 929 return "Split Transaction Error"; 930 default: 931 return "Unknown!!"; 932 } 933 } 934 935 struct xhci_link_trb { 936 /* 64-bit segment pointer*/ 937 __le64 segment_ptr; 938 __le32 intr_target; 939 __le32 control; 940 }; 941 942 /* control bitfields */ 943 #define LINK_TOGGLE (0x1<<1) 944 945 /* Command completion event TRB */ 946 struct xhci_event_cmd { 947 /* Pointer to command TRB, or the value passed by the event data trb */ 948 __le64 cmd_trb; 949 __le32 status; 950 __le32 flags; 951 }; 952 953 /* flags bitmasks */ 954 955 /* Address device - disable SetAddress */ 956 #define TRB_BSR (1<<9) 957 958 /* Configure Endpoint - Deconfigure */ 959 #define TRB_DC (1<<9) 960 961 /* Stop Ring - Transfer State Preserve */ 962 #define TRB_TSP (1<<9) 963 964 enum xhci_ep_reset_type { 965 EP_HARD_RESET, 966 EP_SOFT_RESET, 967 }; 968 969 /* Force Event */ 970 #define TRB_TO_VF_INTR_TARGET(p) (((p) & (0x3ff << 22)) >> 22) 971 #define TRB_TO_VF_ID(p) (((p) & (0xff << 16)) >> 16) 972 973 /* Set Latency Tolerance Value */ 974 #define TRB_TO_BELT(p) (((p) & (0xfff << 16)) >> 16) 975 976 /* Get Port Bandwidth */ 977 #define TRB_TO_DEV_SPEED(p) (((p) & (0xf << 16)) >> 16) 978 979 /* Force Header */ 980 #define TRB_TO_PACKET_TYPE(p) ((p) & 0x1f) 981 #define TRB_TO_ROOTHUB_PORT(p) (((p) & (0xff << 24)) >> 24) 982 983 enum xhci_setup_dev { 984 SETUP_CONTEXT_ONLY, 985 SETUP_CONTEXT_ADDRESS, 986 }; 987 988 /* bits 16:23 are the virtual function ID */ 989 /* bits 24:31 are the slot ID */ 990 #define TRB_TO_SLOT_ID(p) (((p) & (0xff<<24)) >> 24) 991 #define SLOT_ID_FOR_TRB(p) (((p) & 0xff) << 24) 992 993 /* Stop Endpoint TRB - ep_index to endpoint ID for this TRB */ 994 #define TRB_TO_EP_INDEX(p) ((((p) & (0x1f << 16)) >> 16) - 1) 995 #define EP_ID_FOR_TRB(p) ((((p) + 1) & 0x1f) << 16) 996 997 #define SUSPEND_PORT_FOR_TRB(p) (((p) & 1) << 23) 998 #define TRB_TO_SUSPEND_PORT(p) (((p) & (1 << 23)) >> 23) 999 #define LAST_EP_INDEX 30 1000 1001 /* Set TR Dequeue Pointer command TRB fields, 6.4.3.9 */ 1002 #define TRB_TO_STREAM_ID(p) ((((p) & (0xffff << 16)) >> 16)) 1003 #define STREAM_ID_FOR_TRB(p) ((((p)) & 0xffff) << 16) 1004 #define SCT_FOR_TRB(p) (((p) << 1) & 0x7) 1005 1006 /* Link TRB specific fields */ 1007 #define TRB_TC (1<<1) 1008 1009 /* Port Status Change Event TRB fields */ 1010 /* Port ID - bits 31:24 */ 1011 #define GET_PORT_ID(p) (((p) & (0xff << 24)) >> 24) 1012 1013 #define EVENT_DATA (1 << 2) 1014 1015 /* Normal TRB fields */ 1016 /* transfer_len bitmasks - bits 0:16 */ 1017 #define TRB_LEN(p) ((p) & 0x1ffff) 1018 /* TD Size, packets remaining in this TD, bits 21:17 (5 bits, so max 31) */ 1019 #define TRB_TD_SIZE(p) (min((p), (u32)31) << 17) 1020 #define GET_TD_SIZE(p) (((p) & 0x3e0000) >> 17) 1021 /* xhci 1.1 uses the TD_SIZE field for TBC if Extended TBC is enabled (ETE) */ 1022 #define TRB_TD_SIZE_TBC(p) (min((p), (u32)31) << 17) 1023 /* Interrupter Target - which MSI-X vector to target the completion event at */ 1024 #define TRB_INTR_TARGET(p) (((p) & 0x3ff) << 22) 1025 #define GET_INTR_TARGET(p) (((p) >> 22) & 0x3ff) 1026 /* Total burst count field, Rsvdz on xhci 1.1 with Extended TBC enabled (ETE) */ 1027 #define TRB_TBC(p) (((p) & 0x3) << 7) 1028 #define TRB_TLBPC(p) (((p) & 0xf) << 16) 1029 1030 /* Cycle bit - indicates TRB ownership by HC or HCD */ 1031 #define TRB_CYCLE (1<<0) 1032 /* 1033 * Force next event data TRB to be evaluated before task switch. 1034 * Used to pass OS data back after a TD completes. 1035 */ 1036 #define TRB_ENT (1<<1) 1037 /* Interrupt on short packet */ 1038 #define TRB_ISP (1<<2) 1039 /* Set PCIe no snoop attribute */ 1040 #define TRB_NO_SNOOP (1<<3) 1041 /* Chain multiple TRBs into a TD */ 1042 #define TRB_CHAIN (1<<4) 1043 /* Interrupt on completion */ 1044 #define TRB_IOC (1<<5) 1045 /* The buffer pointer contains immediate data */ 1046 #define TRB_IDT (1<<6) 1047 /* TDs smaller than this might use IDT */ 1048 #define TRB_IDT_MAX_SIZE 8 1049 1050 /* Block Event Interrupt */ 1051 #define TRB_BEI (1<<9) 1052 1053 /* Control transfer TRB specific fields */ 1054 #define TRB_DIR_IN (1<<16) 1055 #define TRB_TX_TYPE(p) ((p) << 16) 1056 #define TRB_DATA_OUT 2 1057 #define TRB_DATA_IN 3 1058 1059 /* Isochronous TRB specific fields */ 1060 #define TRB_SIA (1<<31) 1061 #define TRB_FRAME_ID(p) (((p) & 0x7ff) << 20) 1062 1063 /* TRB cache size for xHC with TRB cache */ 1064 #define TRB_CACHE_SIZE_HS 8 1065 #define TRB_CACHE_SIZE_SS 16 1066 1067 struct xhci_generic_trb { 1068 __le32 field[4]; 1069 }; 1070 1071 union xhci_trb { 1072 struct xhci_link_trb link; 1073 struct xhci_transfer_event trans_event; 1074 struct xhci_event_cmd event_cmd; 1075 struct xhci_generic_trb generic; 1076 }; 1077 1078 /* TRB bit mask */ 1079 #define TRB_TYPE_BITMASK (0xfc00) 1080 #define TRB_TYPE(p) ((p) << 10) 1081 #define TRB_FIELD_TO_TYPE(p) (((p) & TRB_TYPE_BITMASK) >> 10) 1082 /* TRB type IDs */ 1083 /* bulk, interrupt, isoc scatter/gather, and control data stage */ 1084 #define TRB_NORMAL 1 1085 /* setup stage for control transfers */ 1086 #define TRB_SETUP 2 1087 /* data stage for control transfers */ 1088 #define TRB_DATA 3 1089 /* status stage for control transfers */ 1090 #define TRB_STATUS 4 1091 /* isoc transfers */ 1092 #define TRB_ISOC 5 1093 /* TRB for linking ring segments */ 1094 #define TRB_LINK 6 1095 #define TRB_EVENT_DATA 7 1096 /* Transfer Ring No-op (not for the command ring) */ 1097 #define TRB_TR_NOOP 8 1098 /* Command TRBs */ 1099 /* Enable Slot Command */ 1100 #define TRB_ENABLE_SLOT 9 1101 /* Disable Slot Command */ 1102 #define TRB_DISABLE_SLOT 10 1103 /* Address Device Command */ 1104 #define TRB_ADDR_DEV 11 1105 /* Configure Endpoint Command */ 1106 #define TRB_CONFIG_EP 12 1107 /* Evaluate Context Command */ 1108 #define TRB_EVAL_CONTEXT 13 1109 /* Reset Endpoint Command */ 1110 #define TRB_RESET_EP 14 1111 /* Stop Transfer Ring Command */ 1112 #define TRB_STOP_RING 15 1113 /* Set Transfer Ring Dequeue Pointer Command */ 1114 #define TRB_SET_DEQ 16 1115 /* Reset Device Command */ 1116 #define TRB_RESET_DEV 17 1117 /* Force Event Command (opt) */ 1118 #define TRB_FORCE_EVENT 18 1119 /* Negotiate Bandwidth Command (opt) */ 1120 #define TRB_NEG_BANDWIDTH 19 1121 /* Set Latency Tolerance Value Command (opt) */ 1122 #define TRB_SET_LT 20 1123 /* Get port bandwidth Command */ 1124 #define TRB_GET_BW 21 1125 /* Force Header Command - generate a transaction or link management packet */ 1126 #define TRB_FORCE_HEADER 22 1127 /* No-op Command - not for transfer rings */ 1128 #define TRB_CMD_NOOP 23 1129 /* TRB IDs 24-31 reserved */ 1130 /* Event TRBS */ 1131 /* Transfer Event */ 1132 #define TRB_TRANSFER 32 1133 /* Command Completion Event */ 1134 #define TRB_COMPLETION 33 1135 /* Port Status Change Event */ 1136 #define TRB_PORT_STATUS 34 1137 /* Bandwidth Request Event (opt) */ 1138 #define TRB_BANDWIDTH_EVENT 35 1139 /* Doorbell Event (opt) */ 1140 #define TRB_DOORBELL 36 1141 /* Host Controller Event */ 1142 #define TRB_HC_EVENT 37 1143 /* Device Notification Event - device sent function wake notification */ 1144 #define TRB_DEV_NOTE 38 1145 /* MFINDEX Wrap Event - microframe counter wrapped */ 1146 #define TRB_MFINDEX_WRAP 39 1147 /* TRB IDs 40-47 reserved, 48-63 is vendor-defined */ 1148 #define TRB_VENDOR_DEFINED_LOW 48 1149 /* Nec vendor-specific command completion event. */ 1150 #define TRB_NEC_CMD_COMP 48 1151 /* Get NEC firmware revision. */ 1152 #define TRB_NEC_GET_FW 49 1153 1154 static inline const char *xhci_trb_type_string(u8 type) 1155 { 1156 switch (type) { 1157 case TRB_NORMAL: 1158 return "Normal"; 1159 case TRB_SETUP: 1160 return "Setup Stage"; 1161 case TRB_DATA: 1162 return "Data Stage"; 1163 case TRB_STATUS: 1164 return "Status Stage"; 1165 case TRB_ISOC: 1166 return "Isoch"; 1167 case TRB_LINK: 1168 return "Link"; 1169 case TRB_EVENT_DATA: 1170 return "Event Data"; 1171 case TRB_TR_NOOP: 1172 return "No-Op"; 1173 case TRB_ENABLE_SLOT: 1174 return "Enable Slot Command"; 1175 case TRB_DISABLE_SLOT: 1176 return "Disable Slot Command"; 1177 case TRB_ADDR_DEV: 1178 return "Address Device Command"; 1179 case TRB_CONFIG_EP: 1180 return "Configure Endpoint Command"; 1181 case TRB_EVAL_CONTEXT: 1182 return "Evaluate Context Command"; 1183 case TRB_RESET_EP: 1184 return "Reset Endpoint Command"; 1185 case TRB_STOP_RING: 1186 return "Stop Ring Command"; 1187 case TRB_SET_DEQ: 1188 return "Set TR Dequeue Pointer Command"; 1189 case TRB_RESET_DEV: 1190 return "Reset Device Command"; 1191 case TRB_FORCE_EVENT: 1192 return "Force Event Command"; 1193 case TRB_NEG_BANDWIDTH: 1194 return "Negotiate Bandwidth Command"; 1195 case TRB_SET_LT: 1196 return "Set Latency Tolerance Value Command"; 1197 case TRB_GET_BW: 1198 return "Get Port Bandwidth Command"; 1199 case TRB_FORCE_HEADER: 1200 return "Force Header Command"; 1201 case TRB_CMD_NOOP: 1202 return "No-Op Command"; 1203 case TRB_TRANSFER: 1204 return "Transfer Event"; 1205 case TRB_COMPLETION: 1206 return "Command Completion Event"; 1207 case TRB_PORT_STATUS: 1208 return "Port Status Change Event"; 1209 case TRB_BANDWIDTH_EVENT: 1210 return "Bandwidth Request Event"; 1211 case TRB_DOORBELL: 1212 return "Doorbell Event"; 1213 case TRB_HC_EVENT: 1214 return "Host Controller Event"; 1215 case TRB_DEV_NOTE: 1216 return "Device Notification Event"; 1217 case TRB_MFINDEX_WRAP: 1218 return "MFINDEX Wrap Event"; 1219 case TRB_NEC_CMD_COMP: 1220 return "NEC Command Completion Event"; 1221 case TRB_NEC_GET_FW: 1222 return "NET Get Firmware Revision Command"; 1223 default: 1224 return "UNKNOWN"; 1225 } 1226 } 1227 1228 #define TRB_TYPE_LINK(x) (((x) & TRB_TYPE_BITMASK) == TRB_TYPE(TRB_LINK)) 1229 /* Above, but for __le32 types -- can avoid work by swapping constants: */ 1230 #define TRB_TYPE_LINK_LE32(x) (((x) & cpu_to_le32(TRB_TYPE_BITMASK)) == \ 1231 cpu_to_le32(TRB_TYPE(TRB_LINK))) 1232 #define TRB_TYPE_NOOP_LE32(x) (((x) & cpu_to_le32(TRB_TYPE_BITMASK)) == \ 1233 cpu_to_le32(TRB_TYPE(TRB_TR_NOOP))) 1234 1235 #define NEC_FW_MINOR(p) (((p) >> 0) & 0xff) 1236 #define NEC_FW_MAJOR(p) (((p) >> 8) & 0xff) 1237 1238 /* 1239 * TRBS_PER_SEGMENT must be a multiple of 4, 1240 * since the command ring is 64-byte aligned. 1241 * It must also be greater than 16. 1242 */ 1243 #define TRBS_PER_SEGMENT 256 1244 /* Allow two commands + a link TRB, along with any reserved command TRBs */ 1245 #define MAX_RSVD_CMD_TRBS (TRBS_PER_SEGMENT - 3) 1246 #define TRB_SEGMENT_SIZE (TRBS_PER_SEGMENT*16) 1247 #define TRB_SEGMENT_SHIFT (ilog2(TRB_SEGMENT_SIZE)) 1248 /* TRB buffer pointers can't cross 64KB boundaries */ 1249 #define TRB_MAX_BUFF_SHIFT 16 1250 #define TRB_MAX_BUFF_SIZE (1 << TRB_MAX_BUFF_SHIFT) 1251 /* How much data is left before the 64KB boundary? */ 1252 #define TRB_BUFF_LEN_UP_TO_BOUNDARY(addr) (TRB_MAX_BUFF_SIZE - \ 1253 (addr & (TRB_MAX_BUFF_SIZE - 1))) 1254 #define MAX_SOFT_RETRY 3 1255 /* 1256 * Limits of consecutive isoc trbs that can Block Event Interrupt (BEI) if 1257 * XHCI_AVOID_BEI quirk is in use. 1258 */ 1259 #define AVOID_BEI_INTERVAL_MIN 8 1260 #define AVOID_BEI_INTERVAL_MAX 32 1261 1262 struct xhci_segment { 1263 union xhci_trb *trbs; 1264 /* private to HCD */ 1265 struct xhci_segment *next; 1266 unsigned int num; 1267 dma_addr_t dma; 1268 /* Max packet sized bounce buffer for td-fragmant alignment */ 1269 dma_addr_t bounce_dma; 1270 void *bounce_buf; 1271 unsigned int bounce_offs; 1272 unsigned int bounce_len; 1273 }; 1274 1275 enum xhci_cancelled_td_status { 1276 TD_DIRTY = 0, 1277 TD_HALTED, 1278 TD_CLEARING_CACHE, 1279 TD_CLEARED, 1280 }; 1281 1282 struct xhci_td { 1283 struct list_head td_list; 1284 struct list_head cancelled_td_list; 1285 int status; 1286 enum xhci_cancelled_td_status cancel_status; 1287 struct urb *urb; 1288 struct xhci_segment *start_seg; 1289 union xhci_trb *first_trb; 1290 union xhci_trb *last_trb; 1291 struct xhci_segment *last_trb_seg; 1292 struct xhci_segment *bounce_seg; 1293 /* actual_length of the URB has already been set */ 1294 bool urb_length_set; 1295 bool error_mid_td; 1296 unsigned int num_trbs; 1297 }; 1298 1299 /* 1300 * xHCI command default timeout value in milliseconds. 1301 * USB 3.2 spec, section 9.2.6.1 1302 */ 1303 #define XHCI_CMD_DEFAULT_TIMEOUT 5000 1304 1305 /* command descriptor */ 1306 struct xhci_cd { 1307 struct xhci_command *command; 1308 union xhci_trb *cmd_trb; 1309 }; 1310 1311 enum xhci_ring_type { 1312 TYPE_CTRL = 0, 1313 TYPE_ISOC, 1314 TYPE_BULK, 1315 TYPE_INTR, 1316 TYPE_STREAM, 1317 TYPE_COMMAND, 1318 TYPE_EVENT, 1319 }; 1320 1321 static inline const char *xhci_ring_type_string(enum xhci_ring_type type) 1322 { 1323 switch (type) { 1324 case TYPE_CTRL: 1325 return "CTRL"; 1326 case TYPE_ISOC: 1327 return "ISOC"; 1328 case TYPE_BULK: 1329 return "BULK"; 1330 case TYPE_INTR: 1331 return "INTR"; 1332 case TYPE_STREAM: 1333 return "STREAM"; 1334 case TYPE_COMMAND: 1335 return "CMD"; 1336 case TYPE_EVENT: 1337 return "EVENT"; 1338 } 1339 1340 return "UNKNOWN"; 1341 } 1342 1343 struct xhci_ring { 1344 struct xhci_segment *first_seg; 1345 struct xhci_segment *last_seg; 1346 union xhci_trb *enqueue; 1347 struct xhci_segment *enq_seg; 1348 union xhci_trb *dequeue; 1349 struct xhci_segment *deq_seg; 1350 struct list_head td_list; 1351 /* 1352 * Write the cycle state into the TRB cycle field to give ownership of 1353 * the TRB to the host controller (if we are the producer), or to check 1354 * if we own the TRB (if we are the consumer). See section 4.9.1. 1355 */ 1356 u32 cycle_state; 1357 unsigned int stream_id; 1358 unsigned int num_segs; 1359 unsigned int num_trbs_free; /* used only by xhci DbC */ 1360 unsigned int bounce_buf_len; 1361 enum xhci_ring_type type; 1362 bool last_td_was_short; 1363 struct radix_tree_root *trb_address_map; 1364 }; 1365 1366 struct xhci_erst_entry { 1367 /* 64-bit event ring segment address */ 1368 __le64 seg_addr; 1369 __le32 seg_size; 1370 /* Set to zero */ 1371 __le32 rsvd; 1372 }; 1373 1374 struct xhci_erst { 1375 struct xhci_erst_entry *entries; 1376 unsigned int num_entries; 1377 /* xhci->event_ring keeps track of segment dma addresses */ 1378 dma_addr_t erst_dma_addr; 1379 /* Num entries the ERST can contain */ 1380 unsigned int erst_size; 1381 }; 1382 1383 struct xhci_scratchpad { 1384 u64 *sp_array; 1385 dma_addr_t sp_dma; 1386 void **sp_buffers; 1387 }; 1388 1389 struct urb_priv { 1390 int num_tds; 1391 int num_tds_done; 1392 struct xhci_td td[] __counted_by(num_tds); 1393 }; 1394 1395 /* Reasonable limit for number of Event Ring segments (spec allows 32k) */ 1396 #define ERST_MAX_SEGS 2 1397 /* Poll every 60 seconds */ 1398 #define POLL_TIMEOUT 60 1399 /* Stop endpoint command timeout (secs) for URB cancellation watchdog timer */ 1400 #define XHCI_STOP_EP_CMD_TIMEOUT 5 1401 /* XXX: Make these module parameters */ 1402 1403 struct s3_save { 1404 u32 command; 1405 u32 dev_nt; 1406 u64 dcbaa_ptr; 1407 u32 config_reg; 1408 }; 1409 1410 /* Use for lpm */ 1411 struct dev_info { 1412 u32 dev_id; 1413 struct list_head list; 1414 }; 1415 1416 struct xhci_bus_state { 1417 unsigned long bus_suspended; 1418 unsigned long next_statechange; 1419 1420 /* Port suspend arrays are indexed by the portnum of the fake roothub */ 1421 /* ports suspend status arrays - max 31 ports for USB2, 15 for USB3 */ 1422 u32 port_c_suspend; 1423 u32 suspended_ports; 1424 u32 port_remote_wakeup; 1425 /* which ports have started to resume */ 1426 unsigned long resuming_ports; 1427 }; 1428 1429 struct xhci_interrupter { 1430 struct xhci_ring *event_ring; 1431 struct xhci_erst erst; 1432 struct xhci_intr_reg __iomem *ir_set; 1433 unsigned int intr_num; 1434 bool ip_autoclear; 1435 u32 isoc_bei_interval; 1436 /* For interrupter registers save and restore over suspend/resume */ 1437 u32 s3_irq_pending; 1438 u32 s3_irq_control; 1439 u32 s3_erst_size; 1440 u64 s3_erst_base; 1441 u64 s3_erst_dequeue; 1442 }; 1443 /* 1444 * It can take up to 20 ms to transition from RExit to U0 on the 1445 * Intel Lynx Point LP xHCI host. 1446 */ 1447 #define XHCI_MAX_REXIT_TIMEOUT_MS 20 1448 struct xhci_port_cap { 1449 u32 *psi; /* array of protocol speed ID entries */ 1450 u8 psi_count; 1451 u8 psi_uid_count; 1452 u8 maj_rev; 1453 u8 min_rev; 1454 }; 1455 1456 struct xhci_port { 1457 __le32 __iomem *addr; 1458 int hw_portnum; 1459 int hcd_portnum; 1460 struct xhci_hub *rhub; 1461 struct xhci_port_cap *port_cap; 1462 unsigned int lpm_incapable:1; 1463 unsigned long resume_timestamp; 1464 bool rexit_active; 1465 /* Slot ID is the index of the device directly connected to the port */ 1466 int slot_id; 1467 struct completion rexit_done; 1468 struct completion u3exit_done; 1469 }; 1470 1471 struct xhci_hub { 1472 struct xhci_port **ports; 1473 unsigned int num_ports; 1474 struct usb_hcd *hcd; 1475 /* keep track of bus suspend info */ 1476 struct xhci_bus_state bus_state; 1477 /* supported prococol extended capabiliy values */ 1478 u8 maj_rev; 1479 u8 min_rev; 1480 }; 1481 1482 /* There is one xhci_hcd structure per controller */ 1483 struct xhci_hcd { 1484 struct usb_hcd *main_hcd; 1485 struct usb_hcd *shared_hcd; 1486 /* glue to PCI and HCD framework */ 1487 struct xhci_cap_regs __iomem *cap_regs; 1488 struct xhci_op_regs __iomem *op_regs; 1489 struct xhci_run_regs __iomem *run_regs; 1490 struct xhci_doorbell_array __iomem *dba; 1491 1492 /* Cached register copies of read-only HC data */ 1493 __u32 hcs_params1; 1494 __u32 hcs_params2; 1495 __u32 hcs_params3; 1496 __u32 hcc_params; 1497 __u32 hcc_params2; 1498 1499 spinlock_t lock; 1500 1501 /* packed release number */ 1502 u8 sbrn; 1503 u16 hci_version; 1504 u8 max_slots; 1505 u16 max_interrupters; 1506 u8 max_ports; 1507 u8 isoc_threshold; 1508 /* imod_interval in ns (I * 250ns) */ 1509 u32 imod_interval; 1510 int event_ring_max; 1511 /* 4KB min, 128MB max */ 1512 int page_size; 1513 /* Valid values are 12 to 20, inclusive */ 1514 int page_shift; 1515 /* MSI-X/MSI vectors */ 1516 int nvecs; 1517 /* optional clocks */ 1518 struct clk *clk; 1519 struct clk *reg_clk; 1520 /* optional reset controller */ 1521 struct reset_control *reset; 1522 /* data structures */ 1523 struct xhci_device_context_array *dcbaa; 1524 struct xhci_interrupter **interrupters; 1525 struct xhci_ring *cmd_ring; 1526 unsigned int cmd_ring_state; 1527 #define CMD_RING_STATE_RUNNING (1 << 0) 1528 #define CMD_RING_STATE_ABORTED (1 << 1) 1529 #define CMD_RING_STATE_STOPPED (1 << 2) 1530 struct list_head cmd_list; 1531 unsigned int cmd_ring_reserved_trbs; 1532 struct delayed_work cmd_timer; 1533 struct completion cmd_ring_stop_completion; 1534 struct xhci_command *current_cmd; 1535 1536 /* Scratchpad */ 1537 struct xhci_scratchpad *scratchpad; 1538 1539 /* slot enabling and address device helpers */ 1540 /* these are not thread safe so use mutex */ 1541 struct mutex mutex; 1542 /* Internal mirror of the HW's dcbaa */ 1543 struct xhci_virt_device *devs[MAX_HC_SLOTS]; 1544 /* For keeping track of bandwidth domains per roothub. */ 1545 struct xhci_root_port_bw_info *rh_bw; 1546 1547 /* DMA pools */ 1548 struct dma_pool *device_pool; 1549 struct dma_pool *segment_pool; 1550 struct dma_pool *small_streams_pool; 1551 struct dma_pool *medium_streams_pool; 1552 1553 /* Host controller watchdog timer structures */ 1554 unsigned int xhc_state; 1555 unsigned long run_graceperiod; 1556 struct s3_save s3; 1557 /* Host controller is dying - not responding to commands. "I'm not dead yet!" 1558 * 1559 * xHC interrupts have been disabled and a watchdog timer will (or has already) 1560 * halt the xHCI host, and complete all URBs with an -ESHUTDOWN code. Any code 1561 * that sees this status (other than the timer that set it) should stop touching 1562 * hardware immediately. Interrupt handlers should return immediately when 1563 * they see this status (any time they drop and re-acquire xhci->lock). 1564 * xhci_urb_dequeue() should call usb_hcd_check_unlink_urb() and return without 1565 * putting the TD on the canceled list, etc. 1566 * 1567 * There are no reports of xHCI host controllers that display this issue. 1568 */ 1569 #define XHCI_STATE_DYING (1 << 0) 1570 #define XHCI_STATE_HALTED (1 << 1) 1571 #define XHCI_STATE_REMOVING (1 << 2) 1572 unsigned long long quirks; 1573 #define XHCI_LINK_TRB_QUIRK BIT_ULL(0) 1574 #define XHCI_RESET_EP_QUIRK BIT_ULL(1) /* Deprecated */ 1575 #define XHCI_NEC_HOST BIT_ULL(2) 1576 #define XHCI_AMD_PLL_FIX BIT_ULL(3) 1577 #define XHCI_SPURIOUS_SUCCESS BIT_ULL(4) 1578 /* 1579 * Certain Intel host controllers have a limit to the number of endpoint 1580 * contexts they can handle. Ideally, they would signal that they can't handle 1581 * anymore endpoint contexts by returning a Resource Error for the Configure 1582 * Endpoint command, but they don't. Instead they expect software to keep track 1583 * of the number of active endpoints for them, across configure endpoint 1584 * commands, reset device commands, disable slot commands, and address device 1585 * commands. 1586 */ 1587 #define XHCI_EP_LIMIT_QUIRK BIT_ULL(5) 1588 #define XHCI_BROKEN_MSI BIT_ULL(6) 1589 #define XHCI_RESET_ON_RESUME BIT_ULL(7) 1590 #define XHCI_SW_BW_CHECKING BIT_ULL(8) 1591 #define XHCI_AMD_0x96_HOST BIT_ULL(9) 1592 #define XHCI_TRUST_TX_LENGTH BIT_ULL(10) 1593 #define XHCI_LPM_SUPPORT BIT_ULL(11) 1594 #define XHCI_INTEL_HOST BIT_ULL(12) 1595 #define XHCI_SPURIOUS_REBOOT BIT_ULL(13) 1596 #define XHCI_COMP_MODE_QUIRK BIT_ULL(14) 1597 #define XHCI_AVOID_BEI BIT_ULL(15) 1598 #define XHCI_PLAT BIT_ULL(16) /* Deprecated */ 1599 #define XHCI_SLOW_SUSPEND BIT_ULL(17) 1600 #define XHCI_SPURIOUS_WAKEUP BIT_ULL(18) 1601 /* For controllers with a broken beyond repair streams implementation */ 1602 #define XHCI_BROKEN_STREAMS BIT_ULL(19) 1603 #define XHCI_PME_STUCK_QUIRK BIT_ULL(20) 1604 #define XHCI_MTK_HOST BIT_ULL(21) 1605 #define XHCI_SSIC_PORT_UNUSED BIT_ULL(22) 1606 #define XHCI_NO_64BIT_SUPPORT BIT_ULL(23) 1607 #define XHCI_MISSING_CAS BIT_ULL(24) 1608 /* For controller with a broken Port Disable implementation */ 1609 #define XHCI_BROKEN_PORT_PED BIT_ULL(25) 1610 #define XHCI_LIMIT_ENDPOINT_INTERVAL_7 BIT_ULL(26) 1611 #define XHCI_U2_DISABLE_WAKE BIT_ULL(27) 1612 #define XHCI_ASMEDIA_MODIFY_FLOWCONTROL BIT_ULL(28) 1613 #define XHCI_HW_LPM_DISABLE BIT_ULL(29) 1614 #define XHCI_SUSPEND_DELAY BIT_ULL(30) 1615 #define XHCI_INTEL_USB_ROLE_SW BIT_ULL(31) 1616 #define XHCI_ZERO_64B_REGS BIT_ULL(32) 1617 #define XHCI_DEFAULT_PM_RUNTIME_ALLOW BIT_ULL(33) 1618 #define XHCI_RESET_PLL_ON_DISCONNECT BIT_ULL(34) 1619 #define XHCI_SNPS_BROKEN_SUSPEND BIT_ULL(35) 1620 #define XHCI_RENESAS_FW_QUIRK BIT_ULL(36) 1621 #define XHCI_SKIP_PHY_INIT BIT_ULL(37) 1622 #define XHCI_DISABLE_SPARSE BIT_ULL(38) 1623 #define XHCI_SG_TRB_CACHE_SIZE_QUIRK BIT_ULL(39) 1624 #define XHCI_NO_SOFT_RETRY BIT_ULL(40) 1625 #define XHCI_BROKEN_D3COLD_S2I BIT_ULL(41) 1626 #define XHCI_EP_CTX_BROKEN_DCS BIT_ULL(42) 1627 #define XHCI_SUSPEND_RESUME_CLKS BIT_ULL(43) 1628 #define XHCI_RESET_TO_DEFAULT BIT_ULL(44) 1629 #define XHCI_ZHAOXIN_TRB_FETCH BIT_ULL(45) 1630 #define XHCI_ZHAOXIN_HOST BIT_ULL(46) 1631 1632 unsigned int num_active_eps; 1633 unsigned int limit_active_eps; 1634 struct xhci_port *hw_ports; 1635 struct xhci_hub usb2_rhub; 1636 struct xhci_hub usb3_rhub; 1637 /* support xHCI 1.0 spec USB2 hardware LPM */ 1638 unsigned hw_lpm_support:1; 1639 /* Broken Suspend flag for SNPS Suspend resume issue */ 1640 unsigned broken_suspend:1; 1641 /* Indicates that omitting hcd is supported if root hub has no ports */ 1642 unsigned allow_single_roothub:1; 1643 /* cached usb2 extened protocol capabilites */ 1644 u32 *ext_caps; 1645 unsigned int num_ext_caps; 1646 /* cached extended protocol port capabilities */ 1647 struct xhci_port_cap *port_caps; 1648 unsigned int num_port_caps; 1649 /* Compliance Mode Recovery Data */ 1650 struct timer_list comp_mode_recovery_timer; 1651 u32 port_status_u0; 1652 u16 test_mode; 1653 /* Compliance Mode Timer Triggered every 2 seconds */ 1654 #define COMP_MODE_RCVRY_MSECS 2000 1655 1656 struct dentry *debugfs_root; 1657 struct dentry *debugfs_slots; 1658 struct list_head regset_list; 1659 1660 void *dbc; 1661 /* platform-specific data -- must come last */ 1662 unsigned long priv[] __aligned(sizeof(s64)); 1663 }; 1664 1665 /* Platform specific overrides to generic XHCI hc_driver ops */ 1666 struct xhci_driver_overrides { 1667 size_t extra_priv_size; 1668 int (*reset)(struct usb_hcd *hcd); 1669 int (*start)(struct usb_hcd *hcd); 1670 int (*add_endpoint)(struct usb_hcd *hcd, struct usb_device *udev, 1671 struct usb_host_endpoint *ep); 1672 int (*drop_endpoint)(struct usb_hcd *hcd, struct usb_device *udev, 1673 struct usb_host_endpoint *ep); 1674 int (*check_bandwidth)(struct usb_hcd *, struct usb_device *); 1675 void (*reset_bandwidth)(struct usb_hcd *, struct usb_device *); 1676 int (*update_hub_device)(struct usb_hcd *hcd, struct usb_device *hdev, 1677 struct usb_tt *tt, gfp_t mem_flags); 1678 int (*hub_control)(struct usb_hcd *hcd, u16 typeReq, u16 wValue, 1679 u16 wIndex, char *buf, u16 wLength); 1680 }; 1681 1682 #define XHCI_CFC_DELAY 10 1683 1684 /* convert between an HCD pointer and the corresponding EHCI_HCD */ 1685 static inline struct xhci_hcd *hcd_to_xhci(struct usb_hcd *hcd) 1686 { 1687 struct usb_hcd *primary_hcd; 1688 1689 if (usb_hcd_is_primary_hcd(hcd)) 1690 primary_hcd = hcd; 1691 else 1692 primary_hcd = hcd->primary_hcd; 1693 1694 return (struct xhci_hcd *) (primary_hcd->hcd_priv); 1695 } 1696 1697 static inline struct usb_hcd *xhci_to_hcd(struct xhci_hcd *xhci) 1698 { 1699 return xhci->main_hcd; 1700 } 1701 1702 static inline struct usb_hcd *xhci_get_usb3_hcd(struct xhci_hcd *xhci) 1703 { 1704 if (xhci->shared_hcd) 1705 return xhci->shared_hcd; 1706 1707 if (!xhci->usb2_rhub.num_ports) 1708 return xhci->main_hcd; 1709 1710 return NULL; 1711 } 1712 1713 static inline bool xhci_hcd_is_usb3(struct usb_hcd *hcd) 1714 { 1715 struct xhci_hcd *xhci = hcd_to_xhci(hcd); 1716 1717 return hcd == xhci_get_usb3_hcd(xhci); 1718 } 1719 1720 static inline bool xhci_has_one_roothub(struct xhci_hcd *xhci) 1721 { 1722 return xhci->allow_single_roothub && 1723 (!xhci->usb2_rhub.num_ports || !xhci->usb3_rhub.num_ports); 1724 } 1725 1726 #define xhci_dbg(xhci, fmt, args...) \ 1727 dev_dbg(xhci_to_hcd(xhci)->self.controller , fmt , ## args) 1728 #define xhci_err(xhci, fmt, args...) \ 1729 dev_err(xhci_to_hcd(xhci)->self.controller , fmt , ## args) 1730 #define xhci_warn(xhci, fmt, args...) \ 1731 dev_warn(xhci_to_hcd(xhci)->self.controller , fmt , ## args) 1732 #define xhci_warn_ratelimited(xhci, fmt, args...) \ 1733 dev_warn_ratelimited(xhci_to_hcd(xhci)->self.controller , fmt , ## args) 1734 #define xhci_info(xhci, fmt, args...) \ 1735 dev_info(xhci_to_hcd(xhci)->self.controller , fmt , ## args) 1736 1737 /* 1738 * Registers should always be accessed with double word or quad word accesses. 1739 * 1740 * Some xHCI implementations may support 64-bit address pointers. Registers 1741 * with 64-bit address pointers should be written to with dword accesses by 1742 * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second. 1743 * xHCI implementations that do not support 64-bit address pointers will ignore 1744 * the high dword, and write order is irrelevant. 1745 */ 1746 static inline u64 xhci_read_64(const struct xhci_hcd *xhci, 1747 __le64 __iomem *regs) 1748 { 1749 return lo_hi_readq(regs); 1750 } 1751 static inline void xhci_write_64(struct xhci_hcd *xhci, 1752 const u64 val, __le64 __iomem *regs) 1753 { 1754 lo_hi_writeq(val, regs); 1755 } 1756 1757 static inline int xhci_link_trb_quirk(struct xhci_hcd *xhci) 1758 { 1759 return xhci->quirks & XHCI_LINK_TRB_QUIRK; 1760 } 1761 1762 /* xHCI debugging */ 1763 char *xhci_get_slot_state(struct xhci_hcd *xhci, 1764 struct xhci_container_ctx *ctx); 1765 void xhci_dbg_trace(struct xhci_hcd *xhci, void (*trace)(struct va_format *), 1766 const char *fmt, ...); 1767 1768 /* xHCI memory management */ 1769 void xhci_mem_cleanup(struct xhci_hcd *xhci); 1770 int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags); 1771 void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id); 1772 int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id, struct usb_device *udev, gfp_t flags); 1773 int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *udev); 1774 void xhci_copy_ep0_dequeue_into_input_ctx(struct xhci_hcd *xhci, 1775 struct usb_device *udev); 1776 unsigned int xhci_get_endpoint_index(struct usb_endpoint_descriptor *desc); 1777 unsigned int xhci_last_valid_endpoint(u32 added_ctxs); 1778 void xhci_endpoint_zero(struct xhci_hcd *xhci, struct xhci_virt_device *virt_dev, struct usb_host_endpoint *ep); 1779 void xhci_update_tt_active_eps(struct xhci_hcd *xhci, 1780 struct xhci_virt_device *virt_dev, 1781 int old_active_eps); 1782 void xhci_clear_endpoint_bw_info(struct xhci_bw_info *bw_info); 1783 void xhci_update_bw_info(struct xhci_hcd *xhci, 1784 struct xhci_container_ctx *in_ctx, 1785 struct xhci_input_control_ctx *ctrl_ctx, 1786 struct xhci_virt_device *virt_dev); 1787 void xhci_endpoint_copy(struct xhci_hcd *xhci, 1788 struct xhci_container_ctx *in_ctx, 1789 struct xhci_container_ctx *out_ctx, 1790 unsigned int ep_index); 1791 void xhci_slot_copy(struct xhci_hcd *xhci, 1792 struct xhci_container_ctx *in_ctx, 1793 struct xhci_container_ctx *out_ctx); 1794 int xhci_endpoint_init(struct xhci_hcd *xhci, struct xhci_virt_device *virt_dev, 1795 struct usb_device *udev, struct usb_host_endpoint *ep, 1796 gfp_t mem_flags); 1797 struct xhci_ring *xhci_ring_alloc(struct xhci_hcd *xhci, 1798 unsigned int num_segs, unsigned int cycle_state, 1799 enum xhci_ring_type type, unsigned int max_packet, gfp_t flags); 1800 void xhci_ring_free(struct xhci_hcd *xhci, struct xhci_ring *ring); 1801 int xhci_ring_expansion(struct xhci_hcd *xhci, struct xhci_ring *ring, 1802 unsigned int num_trbs, gfp_t flags); 1803 void xhci_initialize_ring_info(struct xhci_ring *ring, 1804 unsigned int cycle_state); 1805 void xhci_free_endpoint_ring(struct xhci_hcd *xhci, 1806 struct xhci_virt_device *virt_dev, 1807 unsigned int ep_index); 1808 struct xhci_stream_info *xhci_alloc_stream_info(struct xhci_hcd *xhci, 1809 unsigned int num_stream_ctxs, 1810 unsigned int num_streams, 1811 unsigned int max_packet, gfp_t flags); 1812 void xhci_free_stream_info(struct xhci_hcd *xhci, 1813 struct xhci_stream_info *stream_info); 1814 void xhci_setup_streams_ep_input_ctx(struct xhci_hcd *xhci, 1815 struct xhci_ep_ctx *ep_ctx, 1816 struct xhci_stream_info *stream_info); 1817 void xhci_setup_no_streams_ep_input_ctx(struct xhci_ep_ctx *ep_ctx, 1818 struct xhci_virt_ep *ep); 1819 void xhci_free_device_endpoint_resources(struct xhci_hcd *xhci, 1820 struct xhci_virt_device *virt_dev, bool drop_control_ep); 1821 struct xhci_ring *xhci_dma_to_transfer_ring( 1822 struct xhci_virt_ep *ep, 1823 u64 address); 1824 struct xhci_command *xhci_alloc_command(struct xhci_hcd *xhci, 1825 bool allocate_completion, gfp_t mem_flags); 1826 struct xhci_command *xhci_alloc_command_with_ctx(struct xhci_hcd *xhci, 1827 bool allocate_completion, gfp_t mem_flags); 1828 void xhci_urb_free_priv(struct urb_priv *urb_priv); 1829 void xhci_free_command(struct xhci_hcd *xhci, 1830 struct xhci_command *command); 1831 struct xhci_container_ctx *xhci_alloc_container_ctx(struct xhci_hcd *xhci, 1832 int type, gfp_t flags); 1833 void xhci_free_container_ctx(struct xhci_hcd *xhci, 1834 struct xhci_container_ctx *ctx); 1835 struct xhci_interrupter * 1836 xhci_create_secondary_interrupter(struct usb_hcd *hcd, int num_seg); 1837 void xhci_remove_secondary_interrupter(struct usb_hcd 1838 *hcd, struct xhci_interrupter *ir); 1839 1840 /* xHCI host controller glue */ 1841 typedef void (*xhci_get_quirks_t)(struct device *, struct xhci_hcd *); 1842 int xhci_handshake(void __iomem *ptr, u32 mask, u32 done, u64 timeout_us); 1843 int xhci_handshake_check_state(struct xhci_hcd *xhci, void __iomem *ptr, 1844 u32 mask, u32 done, int usec, unsigned int exit_state); 1845 void xhci_quiesce(struct xhci_hcd *xhci); 1846 int xhci_halt(struct xhci_hcd *xhci); 1847 int xhci_start(struct xhci_hcd *xhci); 1848 int xhci_reset(struct xhci_hcd *xhci, u64 timeout_us); 1849 int xhci_run(struct usb_hcd *hcd); 1850 int xhci_gen_setup(struct usb_hcd *hcd, xhci_get_quirks_t get_quirks); 1851 void xhci_shutdown(struct usb_hcd *hcd); 1852 void xhci_stop(struct usb_hcd *hcd); 1853 void xhci_init_driver(struct hc_driver *drv, 1854 const struct xhci_driver_overrides *over); 1855 int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, 1856 struct usb_host_endpoint *ep); 1857 int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev, 1858 struct usb_host_endpoint *ep); 1859 int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev); 1860 void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev); 1861 int xhci_update_hub_device(struct usb_hcd *hcd, struct usb_device *hdev, 1862 struct usb_tt *tt, gfp_t mem_flags); 1863 int xhci_disable_slot(struct xhci_hcd *xhci, u32 slot_id); 1864 int xhci_ext_cap_init(struct xhci_hcd *xhci); 1865 1866 int xhci_suspend(struct xhci_hcd *xhci, bool do_wakeup); 1867 int xhci_resume(struct xhci_hcd *xhci, pm_message_t msg); 1868 1869 irqreturn_t xhci_irq(struct usb_hcd *hcd); 1870 irqreturn_t xhci_msi_irq(int irq, void *hcd); 1871 int xhci_alloc_dev(struct usb_hcd *hcd, struct usb_device *udev); 1872 int xhci_alloc_tt_info(struct xhci_hcd *xhci, 1873 struct xhci_virt_device *virt_dev, 1874 struct usb_device *hdev, 1875 struct usb_tt *tt, gfp_t mem_flags); 1876 1877 /* xHCI ring, segment, TRB, and TD functions */ 1878 dma_addr_t xhci_trb_virt_to_dma(struct xhci_segment *seg, union xhci_trb *trb); 1879 struct xhci_segment *trb_in_td(struct xhci_hcd *xhci, 1880 struct xhci_segment *start_seg, union xhci_trb *start_trb, 1881 union xhci_trb *end_trb, dma_addr_t suspect_dma, bool debug); 1882 int xhci_is_vendor_info_code(struct xhci_hcd *xhci, unsigned int trb_comp_code); 1883 void xhci_ring_cmd_db(struct xhci_hcd *xhci); 1884 int xhci_queue_slot_control(struct xhci_hcd *xhci, struct xhci_command *cmd, 1885 u32 trb_type, u32 slot_id); 1886 int xhci_queue_address_device(struct xhci_hcd *xhci, struct xhci_command *cmd, 1887 dma_addr_t in_ctx_ptr, u32 slot_id, enum xhci_setup_dev); 1888 int xhci_queue_vendor_command(struct xhci_hcd *xhci, struct xhci_command *cmd, 1889 u32 field1, u32 field2, u32 field3, u32 field4); 1890 int xhci_queue_stop_endpoint(struct xhci_hcd *xhci, struct xhci_command *cmd, 1891 int slot_id, unsigned int ep_index, int suspend); 1892 int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct urb *urb, 1893 int slot_id, unsigned int ep_index); 1894 int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct urb *urb, 1895 int slot_id, unsigned int ep_index); 1896 int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct urb *urb, 1897 int slot_id, unsigned int ep_index); 1898 int xhci_queue_isoc_tx_prepare(struct xhci_hcd *xhci, gfp_t mem_flags, 1899 struct urb *urb, int slot_id, unsigned int ep_index); 1900 int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, 1901 struct xhci_command *cmd, dma_addr_t in_ctx_ptr, u32 slot_id, 1902 bool command_must_succeed); 1903 int xhci_queue_evaluate_context(struct xhci_hcd *xhci, struct xhci_command *cmd, 1904 dma_addr_t in_ctx_ptr, u32 slot_id, bool command_must_succeed); 1905 int xhci_queue_reset_ep(struct xhci_hcd *xhci, struct xhci_command *cmd, 1906 int slot_id, unsigned int ep_index, 1907 enum xhci_ep_reset_type reset_type); 1908 int xhci_queue_reset_device(struct xhci_hcd *xhci, struct xhci_command *cmd, 1909 u32 slot_id); 1910 void xhci_cleanup_stalled_ring(struct xhci_hcd *xhci, unsigned int slot_id, 1911 unsigned int ep_index, unsigned int stream_id, 1912 struct xhci_td *td); 1913 void xhci_stop_endpoint_command_watchdog(struct timer_list *t); 1914 void xhci_handle_command_timeout(struct work_struct *work); 1915 1916 void xhci_ring_ep_doorbell(struct xhci_hcd *xhci, unsigned int slot_id, 1917 unsigned int ep_index, unsigned int stream_id); 1918 void xhci_ring_doorbell_for_active_rings(struct xhci_hcd *xhci, 1919 unsigned int slot_id, 1920 unsigned int ep_index); 1921 void xhci_cleanup_command_queue(struct xhci_hcd *xhci); 1922 void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring); 1923 unsigned int count_trbs(u64 addr, u64 len); 1924 1925 /* xHCI roothub code */ 1926 void xhci_set_link_state(struct xhci_hcd *xhci, struct xhci_port *port, 1927 u32 link_state); 1928 void xhci_test_and_clear_bit(struct xhci_hcd *xhci, struct xhci_port *port, 1929 u32 port_bit); 1930 int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex, 1931 char *buf, u16 wLength); 1932 int xhci_hub_status_data(struct usb_hcd *hcd, char *buf); 1933 int xhci_find_raw_port_number(struct usb_hcd *hcd, int port1); 1934 struct xhci_hub *xhci_get_rhub(struct usb_hcd *hcd); 1935 1936 void xhci_hc_died(struct xhci_hcd *xhci); 1937 1938 #ifdef CONFIG_PM 1939 int xhci_bus_suspend(struct usb_hcd *hcd); 1940 int xhci_bus_resume(struct usb_hcd *hcd); 1941 unsigned long xhci_get_resuming_ports(struct usb_hcd *hcd); 1942 #else 1943 #define xhci_bus_suspend NULL 1944 #define xhci_bus_resume NULL 1945 #define xhci_get_resuming_ports NULL 1946 #endif /* CONFIG_PM */ 1947 1948 u32 xhci_port_state_to_neutral(u32 state); 1949 void xhci_ring_device(struct xhci_hcd *xhci, int slot_id); 1950 1951 /* xHCI contexts */ 1952 struct xhci_input_control_ctx *xhci_get_input_control_ctx(struct xhci_container_ctx *ctx); 1953 struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx); 1954 struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int ep_index); 1955 1956 struct xhci_ring *xhci_triad_to_transfer_ring(struct xhci_hcd *xhci, 1957 unsigned int slot_id, unsigned int ep_index, 1958 unsigned int stream_id); 1959 1960 static inline struct xhci_ring *xhci_urb_to_transfer_ring(struct xhci_hcd *xhci, 1961 struct urb *urb) 1962 { 1963 return xhci_triad_to_transfer_ring(xhci, urb->dev->slot_id, 1964 xhci_get_endpoint_index(&urb->ep->desc), 1965 urb->stream_id); 1966 } 1967 1968 /* 1969 * TODO: As per spec Isochronous IDT transmissions are supported. We bypass 1970 * them anyways as we where unable to find a device that matches the 1971 * constraints. 1972 */ 1973 static inline bool xhci_urb_suitable_for_idt(struct urb *urb) 1974 { 1975 if (!usb_endpoint_xfer_isoc(&urb->ep->desc) && usb_urb_dir_out(urb) && 1976 usb_endpoint_maxp(&urb->ep->desc) >= TRB_IDT_MAX_SIZE && 1977 urb->transfer_buffer_length <= TRB_IDT_MAX_SIZE && 1978 !(urb->transfer_flags & URB_NO_TRANSFER_DMA_MAP) && 1979 !urb->num_sgs) 1980 return true; 1981 1982 return false; 1983 } 1984 1985 static inline char *xhci_slot_state_string(u32 state) 1986 { 1987 switch (state) { 1988 case SLOT_STATE_ENABLED: 1989 return "enabled/disabled"; 1990 case SLOT_STATE_DEFAULT: 1991 return "default"; 1992 case SLOT_STATE_ADDRESSED: 1993 return "addressed"; 1994 case SLOT_STATE_CONFIGURED: 1995 return "configured"; 1996 default: 1997 return "reserved"; 1998 } 1999 } 2000 2001 static inline const char *xhci_decode_trb(char *str, size_t size, 2002 u32 field0, u32 field1, u32 field2, u32 field3) 2003 { 2004 int type = TRB_FIELD_TO_TYPE(field3); 2005 2006 switch (type) { 2007 case TRB_LINK: 2008 snprintf(str, size, 2009 "LINK %08x%08x intr %d type '%s' flags %c:%c:%c:%c", 2010 field1, field0, GET_INTR_TARGET(field2), 2011 xhci_trb_type_string(type), 2012 field3 & TRB_IOC ? 'I' : 'i', 2013 field3 & TRB_CHAIN ? 'C' : 'c', 2014 field3 & TRB_TC ? 'T' : 't', 2015 field3 & TRB_CYCLE ? 'C' : 'c'); 2016 break; 2017 case TRB_TRANSFER: 2018 case TRB_COMPLETION: 2019 case TRB_PORT_STATUS: 2020 case TRB_BANDWIDTH_EVENT: 2021 case TRB_DOORBELL: 2022 case TRB_HC_EVENT: 2023 case TRB_DEV_NOTE: 2024 case TRB_MFINDEX_WRAP: 2025 snprintf(str, size, 2026 "TRB %08x%08x status '%s' len %d slot %d ep %d type '%s' flags %c:%c", 2027 field1, field0, 2028 xhci_trb_comp_code_string(GET_COMP_CODE(field2)), 2029 EVENT_TRB_LEN(field2), TRB_TO_SLOT_ID(field3), 2030 /* Macro decrements 1, maybe it shouldn't?!? */ 2031 TRB_TO_EP_INDEX(field3) + 1, 2032 xhci_trb_type_string(type), 2033 field3 & EVENT_DATA ? 'E' : 'e', 2034 field3 & TRB_CYCLE ? 'C' : 'c'); 2035 2036 break; 2037 case TRB_SETUP: 2038 snprintf(str, size, 2039 "bRequestType %02x bRequest %02x wValue %02x%02x wIndex %02x%02x wLength %d length %d TD size %d intr %d type '%s' flags %c:%c:%c", 2040 field0 & 0xff, 2041 (field0 & 0xff00) >> 8, 2042 (field0 & 0xff000000) >> 24, 2043 (field0 & 0xff0000) >> 16, 2044 (field1 & 0xff00) >> 8, 2045 field1 & 0xff, 2046 (field1 & 0xff000000) >> 16 | 2047 (field1 & 0xff0000) >> 16, 2048 TRB_LEN(field2), GET_TD_SIZE(field2), 2049 GET_INTR_TARGET(field2), 2050 xhci_trb_type_string(type), 2051 field3 & TRB_IDT ? 'I' : 'i', 2052 field3 & TRB_IOC ? 'I' : 'i', 2053 field3 & TRB_CYCLE ? 'C' : 'c'); 2054 break; 2055 case TRB_DATA: 2056 snprintf(str, size, 2057 "Buffer %08x%08x length %d TD size %d intr %d type '%s' flags %c:%c:%c:%c:%c:%c:%c", 2058 field1, field0, TRB_LEN(field2), GET_TD_SIZE(field2), 2059 GET_INTR_TARGET(field2), 2060 xhci_trb_type_string(type), 2061 field3 & TRB_IDT ? 'I' : 'i', 2062 field3 & TRB_IOC ? 'I' : 'i', 2063 field3 & TRB_CHAIN ? 'C' : 'c', 2064 field3 & TRB_NO_SNOOP ? 'S' : 's', 2065 field3 & TRB_ISP ? 'I' : 'i', 2066 field3 & TRB_ENT ? 'E' : 'e', 2067 field3 & TRB_CYCLE ? 'C' : 'c'); 2068 break; 2069 case TRB_STATUS: 2070 snprintf(str, size, 2071 "Buffer %08x%08x length %d TD size %d intr %d type '%s' flags %c:%c:%c:%c", 2072 field1, field0, TRB_LEN(field2), GET_TD_SIZE(field2), 2073 GET_INTR_TARGET(field2), 2074 xhci_trb_type_string(type), 2075 field3 & TRB_IOC ? 'I' : 'i', 2076 field3 & TRB_CHAIN ? 'C' : 'c', 2077 field3 & TRB_ENT ? 'E' : 'e', 2078 field3 & TRB_CYCLE ? 'C' : 'c'); 2079 break; 2080 case TRB_NORMAL: 2081 case TRB_ISOC: 2082 case TRB_EVENT_DATA: 2083 case TRB_TR_NOOP: 2084 snprintf(str, size, 2085 "Buffer %08x%08x length %d TD size %d intr %d type '%s' flags %c:%c:%c:%c:%c:%c:%c:%c", 2086 field1, field0, TRB_LEN(field2), GET_TD_SIZE(field2), 2087 GET_INTR_TARGET(field2), 2088 xhci_trb_type_string(type), 2089 field3 & TRB_BEI ? 'B' : 'b', 2090 field3 & TRB_IDT ? 'I' : 'i', 2091 field3 & TRB_IOC ? 'I' : 'i', 2092 field3 & TRB_CHAIN ? 'C' : 'c', 2093 field3 & TRB_NO_SNOOP ? 'S' : 's', 2094 field3 & TRB_ISP ? 'I' : 'i', 2095 field3 & TRB_ENT ? 'E' : 'e', 2096 field3 & TRB_CYCLE ? 'C' : 'c'); 2097 break; 2098 2099 case TRB_CMD_NOOP: 2100 case TRB_ENABLE_SLOT: 2101 snprintf(str, size, 2102 "%s: flags %c", 2103 xhci_trb_type_string(type), 2104 field3 & TRB_CYCLE ? 'C' : 'c'); 2105 break; 2106 case TRB_DISABLE_SLOT: 2107 case TRB_NEG_BANDWIDTH: 2108 snprintf(str, size, 2109 "%s: slot %d flags %c", 2110 xhci_trb_type_string(type), 2111 TRB_TO_SLOT_ID(field3), 2112 field3 & TRB_CYCLE ? 'C' : 'c'); 2113 break; 2114 case TRB_ADDR_DEV: 2115 snprintf(str, size, 2116 "%s: ctx %08x%08x slot %d flags %c:%c", 2117 xhci_trb_type_string(type), 2118 field1, field0, 2119 TRB_TO_SLOT_ID(field3), 2120 field3 & TRB_BSR ? 'B' : 'b', 2121 field3 & TRB_CYCLE ? 'C' : 'c'); 2122 break; 2123 case TRB_CONFIG_EP: 2124 snprintf(str, size, 2125 "%s: ctx %08x%08x slot %d flags %c:%c", 2126 xhci_trb_type_string(type), 2127 field1, field0, 2128 TRB_TO_SLOT_ID(field3), 2129 field3 & TRB_DC ? 'D' : 'd', 2130 field3 & TRB_CYCLE ? 'C' : 'c'); 2131 break; 2132 case TRB_EVAL_CONTEXT: 2133 snprintf(str, size, 2134 "%s: ctx %08x%08x slot %d flags %c", 2135 xhci_trb_type_string(type), 2136 field1, field0, 2137 TRB_TO_SLOT_ID(field3), 2138 field3 & TRB_CYCLE ? 'C' : 'c'); 2139 break; 2140 case TRB_RESET_EP: 2141 snprintf(str, size, 2142 "%s: ctx %08x%08x slot %d ep %d flags %c:%c", 2143 xhci_trb_type_string(type), 2144 field1, field0, 2145 TRB_TO_SLOT_ID(field3), 2146 /* Macro decrements 1, maybe it shouldn't?!? */ 2147 TRB_TO_EP_INDEX(field3) + 1, 2148 field3 & TRB_TSP ? 'T' : 't', 2149 field3 & TRB_CYCLE ? 'C' : 'c'); 2150 break; 2151 case TRB_STOP_RING: 2152 snprintf(str, size, 2153 "%s: slot %d sp %d ep %d flags %c", 2154 xhci_trb_type_string(type), 2155 TRB_TO_SLOT_ID(field3), 2156 TRB_TO_SUSPEND_PORT(field3), 2157 /* Macro decrements 1, maybe it shouldn't?!? */ 2158 TRB_TO_EP_INDEX(field3) + 1, 2159 field3 & TRB_CYCLE ? 'C' : 'c'); 2160 break; 2161 case TRB_SET_DEQ: 2162 snprintf(str, size, 2163 "%s: deq %08x%08x stream %d slot %d ep %d flags %c", 2164 xhci_trb_type_string(type), 2165 field1, field0, 2166 TRB_TO_STREAM_ID(field2), 2167 TRB_TO_SLOT_ID(field3), 2168 /* Macro decrements 1, maybe it shouldn't?!? */ 2169 TRB_TO_EP_INDEX(field3) + 1, 2170 field3 & TRB_CYCLE ? 'C' : 'c'); 2171 break; 2172 case TRB_RESET_DEV: 2173 snprintf(str, size, 2174 "%s: slot %d flags %c", 2175 xhci_trb_type_string(type), 2176 TRB_TO_SLOT_ID(field3), 2177 field3 & TRB_CYCLE ? 'C' : 'c'); 2178 break; 2179 case TRB_FORCE_EVENT: 2180 snprintf(str, size, 2181 "%s: event %08x%08x vf intr %d vf id %d flags %c", 2182 xhci_trb_type_string(type), 2183 field1, field0, 2184 TRB_TO_VF_INTR_TARGET(field2), 2185 TRB_TO_VF_ID(field3), 2186 field3 & TRB_CYCLE ? 'C' : 'c'); 2187 break; 2188 case TRB_SET_LT: 2189 snprintf(str, size, 2190 "%s: belt %d flags %c", 2191 xhci_trb_type_string(type), 2192 TRB_TO_BELT(field3), 2193 field3 & TRB_CYCLE ? 'C' : 'c'); 2194 break; 2195 case TRB_GET_BW: 2196 snprintf(str, size, 2197 "%s: ctx %08x%08x slot %d speed %d flags %c", 2198 xhci_trb_type_string(type), 2199 field1, field0, 2200 TRB_TO_SLOT_ID(field3), 2201 TRB_TO_DEV_SPEED(field3), 2202 field3 & TRB_CYCLE ? 'C' : 'c'); 2203 break; 2204 case TRB_FORCE_HEADER: 2205 snprintf(str, size, 2206 "%s: info %08x%08x%08x pkt type %d roothub port %d flags %c", 2207 xhci_trb_type_string(type), 2208 field2, field1, field0 & 0xffffffe0, 2209 TRB_TO_PACKET_TYPE(field0), 2210 TRB_TO_ROOTHUB_PORT(field3), 2211 field3 & TRB_CYCLE ? 'C' : 'c'); 2212 break; 2213 default: 2214 snprintf(str, size, 2215 "type '%s' -> raw %08x %08x %08x %08x", 2216 xhci_trb_type_string(type), 2217 field0, field1, field2, field3); 2218 } 2219 2220 return str; 2221 } 2222 2223 static inline const char *xhci_decode_ctrl_ctx(char *str, 2224 unsigned long drop, unsigned long add) 2225 { 2226 unsigned int bit; 2227 int ret = 0; 2228 2229 str[0] = '\0'; 2230 2231 if (drop) { 2232 ret = sprintf(str, "Drop:"); 2233 for_each_set_bit(bit, &drop, 32) 2234 ret += sprintf(str + ret, " %d%s", 2235 bit / 2, 2236 bit % 2 ? "in":"out"); 2237 ret += sprintf(str + ret, ", "); 2238 } 2239 2240 if (add) { 2241 ret += sprintf(str + ret, "Add:%s%s", 2242 (add & SLOT_FLAG) ? " slot":"", 2243 (add & EP0_FLAG) ? " ep0":""); 2244 add &= ~(SLOT_FLAG | EP0_FLAG); 2245 for_each_set_bit(bit, &add, 32) 2246 ret += sprintf(str + ret, " %d%s", 2247 bit / 2, 2248 bit % 2 ? "in":"out"); 2249 } 2250 return str; 2251 } 2252 2253 static inline const char *xhci_decode_slot_context(char *str, 2254 u32 info, u32 info2, u32 tt_info, u32 state) 2255 { 2256 u32 speed; 2257 u32 hub; 2258 u32 mtt; 2259 int ret = 0; 2260 2261 speed = info & DEV_SPEED; 2262 hub = info & DEV_HUB; 2263 mtt = info & DEV_MTT; 2264 2265 ret = sprintf(str, "RS %05x %s%s%s Ctx Entries %d MEL %d us Port# %d/%d", 2266 info & ROUTE_STRING_MASK, 2267 ({ char *s; 2268 switch (speed) { 2269 case SLOT_SPEED_FS: 2270 s = "full-speed"; 2271 break; 2272 case SLOT_SPEED_LS: 2273 s = "low-speed"; 2274 break; 2275 case SLOT_SPEED_HS: 2276 s = "high-speed"; 2277 break; 2278 case SLOT_SPEED_SS: 2279 s = "super-speed"; 2280 break; 2281 case SLOT_SPEED_SSP: 2282 s = "super-speed plus"; 2283 break; 2284 default: 2285 s = "UNKNOWN speed"; 2286 } s; }), 2287 mtt ? " multi-TT" : "", 2288 hub ? " Hub" : "", 2289 (info & LAST_CTX_MASK) >> 27, 2290 info2 & MAX_EXIT, 2291 DEVINFO_TO_ROOT_HUB_PORT(info2), 2292 DEVINFO_TO_MAX_PORTS(info2)); 2293 2294 ret += sprintf(str + ret, " [TT Slot %d Port# %d TTT %d Intr %d] Addr %d State %s", 2295 tt_info & TT_SLOT, (tt_info & TT_PORT) >> 8, 2296 GET_TT_THINK_TIME(tt_info), GET_INTR_TARGET(tt_info), 2297 state & DEV_ADDR_MASK, 2298 xhci_slot_state_string(GET_SLOT_STATE(state))); 2299 2300 return str; 2301 } 2302 2303 2304 static inline const char *xhci_portsc_link_state_string(u32 portsc) 2305 { 2306 switch (portsc & PORT_PLS_MASK) { 2307 case XDEV_U0: 2308 return "U0"; 2309 case XDEV_U1: 2310 return "U1"; 2311 case XDEV_U2: 2312 return "U2"; 2313 case XDEV_U3: 2314 return "U3"; 2315 case XDEV_DISABLED: 2316 return "Disabled"; 2317 case XDEV_RXDETECT: 2318 return "RxDetect"; 2319 case XDEV_INACTIVE: 2320 return "Inactive"; 2321 case XDEV_POLLING: 2322 return "Polling"; 2323 case XDEV_RECOVERY: 2324 return "Recovery"; 2325 case XDEV_HOT_RESET: 2326 return "Hot Reset"; 2327 case XDEV_COMP_MODE: 2328 return "Compliance mode"; 2329 case XDEV_TEST_MODE: 2330 return "Test mode"; 2331 case XDEV_RESUME: 2332 return "Resume"; 2333 default: 2334 break; 2335 } 2336 return "Unknown"; 2337 } 2338 2339 static inline const char *xhci_decode_portsc(char *str, u32 portsc) 2340 { 2341 int ret; 2342 2343 ret = sprintf(str, "%s %s %s Link:%s PortSpeed:%d ", 2344 portsc & PORT_POWER ? "Powered" : "Powered-off", 2345 portsc & PORT_CONNECT ? "Connected" : "Not-connected", 2346 portsc & PORT_PE ? "Enabled" : "Disabled", 2347 xhci_portsc_link_state_string(portsc), 2348 DEV_PORT_SPEED(portsc)); 2349 2350 if (portsc & PORT_OC) 2351 ret += sprintf(str + ret, "OverCurrent "); 2352 if (portsc & PORT_RESET) 2353 ret += sprintf(str + ret, "In-Reset "); 2354 2355 ret += sprintf(str + ret, "Change: "); 2356 if (portsc & PORT_CSC) 2357 ret += sprintf(str + ret, "CSC "); 2358 if (portsc & PORT_PEC) 2359 ret += sprintf(str + ret, "PEC "); 2360 if (portsc & PORT_WRC) 2361 ret += sprintf(str + ret, "WRC "); 2362 if (portsc & PORT_OCC) 2363 ret += sprintf(str + ret, "OCC "); 2364 if (portsc & PORT_RC) 2365 ret += sprintf(str + ret, "PRC "); 2366 if (portsc & PORT_PLC) 2367 ret += sprintf(str + ret, "PLC "); 2368 if (portsc & PORT_CEC) 2369 ret += sprintf(str + ret, "CEC "); 2370 if (portsc & PORT_CAS) 2371 ret += sprintf(str + ret, "CAS "); 2372 2373 ret += sprintf(str + ret, "Wake: "); 2374 if (portsc & PORT_WKCONN_E) 2375 ret += sprintf(str + ret, "WCE "); 2376 if (portsc & PORT_WKDISC_E) 2377 ret += sprintf(str + ret, "WDE "); 2378 if (portsc & PORT_WKOC_E) 2379 ret += sprintf(str + ret, "WOE "); 2380 2381 return str; 2382 } 2383 2384 static inline const char *xhci_decode_usbsts(char *str, u32 usbsts) 2385 { 2386 int ret = 0; 2387 2388 ret = sprintf(str, " 0x%08x", usbsts); 2389 2390 if (usbsts == ~(u32)0) 2391 return str; 2392 2393 if (usbsts & STS_HALT) 2394 ret += sprintf(str + ret, " HCHalted"); 2395 if (usbsts & STS_FATAL) 2396 ret += sprintf(str + ret, " HSE"); 2397 if (usbsts & STS_EINT) 2398 ret += sprintf(str + ret, " EINT"); 2399 if (usbsts & STS_PORT) 2400 ret += sprintf(str + ret, " PCD"); 2401 if (usbsts & STS_SAVE) 2402 ret += sprintf(str + ret, " SSS"); 2403 if (usbsts & STS_RESTORE) 2404 ret += sprintf(str + ret, " RSS"); 2405 if (usbsts & STS_SRE) 2406 ret += sprintf(str + ret, " SRE"); 2407 if (usbsts & STS_CNR) 2408 ret += sprintf(str + ret, " CNR"); 2409 if (usbsts & STS_HCE) 2410 ret += sprintf(str + ret, " HCE"); 2411 2412 return str; 2413 } 2414 2415 static inline const char *xhci_decode_doorbell(char *str, u32 slot, u32 doorbell) 2416 { 2417 u8 ep; 2418 u16 stream; 2419 int ret; 2420 2421 ep = (doorbell & 0xff); 2422 stream = doorbell >> 16; 2423 2424 if (slot == 0) { 2425 sprintf(str, "Command Ring %d", doorbell); 2426 return str; 2427 } 2428 ret = sprintf(str, "Slot %d ", slot); 2429 if (ep > 0 && ep < 32) 2430 ret = sprintf(str + ret, "ep%d%s", 2431 ep / 2, 2432 ep % 2 ? "in" : "out"); 2433 else if (ep == 0 || ep < 248) 2434 ret = sprintf(str + ret, "Reserved %d", ep); 2435 else 2436 ret = sprintf(str + ret, "Vendor Defined %d", ep); 2437 if (stream) 2438 ret = sprintf(str + ret, " Stream %d", stream); 2439 2440 return str; 2441 } 2442 2443 static inline const char *xhci_ep_state_string(u8 state) 2444 { 2445 switch (state) { 2446 case EP_STATE_DISABLED: 2447 return "disabled"; 2448 case EP_STATE_RUNNING: 2449 return "running"; 2450 case EP_STATE_HALTED: 2451 return "halted"; 2452 case EP_STATE_STOPPED: 2453 return "stopped"; 2454 case EP_STATE_ERROR: 2455 return "error"; 2456 default: 2457 return "INVALID"; 2458 } 2459 } 2460 2461 static inline const char *xhci_ep_type_string(u8 type) 2462 { 2463 switch (type) { 2464 case ISOC_OUT_EP: 2465 return "Isoc OUT"; 2466 case BULK_OUT_EP: 2467 return "Bulk OUT"; 2468 case INT_OUT_EP: 2469 return "Int OUT"; 2470 case CTRL_EP: 2471 return "Ctrl"; 2472 case ISOC_IN_EP: 2473 return "Isoc IN"; 2474 case BULK_IN_EP: 2475 return "Bulk IN"; 2476 case INT_IN_EP: 2477 return "Int IN"; 2478 default: 2479 return "INVALID"; 2480 } 2481 } 2482 2483 static inline const char *xhci_decode_ep_context(char *str, u32 info, 2484 u32 info2, u64 deq, u32 tx_info) 2485 { 2486 int ret; 2487 2488 u32 esit; 2489 u16 maxp; 2490 u16 avg; 2491 2492 u8 max_pstr; 2493 u8 ep_state; 2494 u8 interval; 2495 u8 ep_type; 2496 u8 burst; 2497 u8 cerr; 2498 u8 mult; 2499 2500 bool lsa; 2501 bool hid; 2502 2503 esit = CTX_TO_MAX_ESIT_PAYLOAD_HI(info) << 16 | 2504 CTX_TO_MAX_ESIT_PAYLOAD(tx_info); 2505 2506 ep_state = info & EP_STATE_MASK; 2507 max_pstr = CTX_TO_EP_MAXPSTREAMS(info); 2508 interval = CTX_TO_EP_INTERVAL(info); 2509 mult = CTX_TO_EP_MULT(info) + 1; 2510 lsa = !!(info & EP_HAS_LSA); 2511 2512 cerr = (info2 & (3 << 1)) >> 1; 2513 ep_type = CTX_TO_EP_TYPE(info2); 2514 hid = !!(info2 & (1 << 7)); 2515 burst = CTX_TO_MAX_BURST(info2); 2516 maxp = MAX_PACKET_DECODED(info2); 2517 2518 avg = EP_AVG_TRB_LENGTH(tx_info); 2519 2520 ret = sprintf(str, "State %s mult %d max P. Streams %d %s", 2521 xhci_ep_state_string(ep_state), mult, 2522 max_pstr, lsa ? "LSA " : ""); 2523 2524 ret += sprintf(str + ret, "interval %d us max ESIT payload %d CErr %d ", 2525 (1 << interval) * 125, esit, cerr); 2526 2527 ret += sprintf(str + ret, "Type %s %sburst %d maxp %d deq %016llx ", 2528 xhci_ep_type_string(ep_type), hid ? "HID" : "", 2529 burst, maxp, deq); 2530 2531 ret += sprintf(str + ret, "avg trb len %d", avg); 2532 2533 return str; 2534 } 2535 2536 #endif /* __LINUX_XHCI_HCD_H */ 2537