1 /* 2 * omap_udc.c -- for OMAP full speed udc; most chips support OTG. 3 * 4 * Copyright (C) 2004 Texas Instruments, Inc. 5 * Copyright (C) 2004-2005 David Brownell 6 * 7 * OMAP2 & DMA support by Kyungmin Park <kyungmin.park@samsung.com> 8 * 9 * This program is free software; you can redistribute it and/or modify 10 * it under the terms of the GNU General Public License as published by 11 * the Free Software Foundation; either version 2 of the License, or 12 * (at your option) any later version. 13 */ 14 15 #undef DEBUG 16 #undef VERBOSE 17 18 #include <linux/module.h> 19 #include <linux/kernel.h> 20 #include <linux/ioport.h> 21 #include <linux/types.h> 22 #include <linux/errno.h> 23 #include <linux/delay.h> 24 #include <linux/slab.h> 25 #include <linux/timer.h> 26 #include <linux/list.h> 27 #include <linux/interrupt.h> 28 #include <linux/proc_fs.h> 29 #include <linux/mm.h> 30 #include <linux/moduleparam.h> 31 #include <linux/platform_device.h> 32 #include <linux/usb/ch9.h> 33 #include <linux/usb/gadget.h> 34 #include <linux/usb/otg.h> 35 #include <linux/dma-mapping.h> 36 #include <linux/clk.h> 37 #include <linux/err.h> 38 #include <linux/prefetch.h> 39 #include <linux/io.h> 40 41 #include <asm/byteorder.h> 42 #include <asm/irq.h> 43 #include <asm/unaligned.h> 44 #include <asm/mach-types.h> 45 46 #include <linux/omap-dma.h> 47 48 #include <mach/usb.h> 49 50 #include "omap_udc.h" 51 52 #undef USB_TRACE 53 54 /* bulk DMA seems to be behaving for both IN and OUT */ 55 #define USE_DMA 56 57 /* ISO too */ 58 #define USE_ISO 59 60 #define DRIVER_DESC "OMAP UDC driver" 61 #define DRIVER_VERSION "4 October 2004" 62 63 #define OMAP_DMA_USB_W2FC_TX0 29 64 #define OMAP_DMA_USB_W2FC_RX0 26 65 66 /* 67 * The OMAP UDC needs _very_ early endpoint setup: before enabling the 68 * D+ pullup to allow enumeration. That's too early for the gadget 69 * framework to use from usb_endpoint_enable(), which happens after 70 * enumeration as part of activating an interface. (But if we add an 71 * optional new "UDC not yet running" state to the gadget driver model, 72 * even just during driver binding, the endpoint autoconfig logic is the 73 * natural spot to manufacture new endpoints.) 74 * 75 * So instead of using endpoint enable calls to control the hardware setup, 76 * this driver defines a "fifo mode" parameter. It's used during driver 77 * initialization to choose among a set of pre-defined endpoint configs. 78 * See omap_udc_setup() for available modes, or to add others. That code 79 * lives in an init section, so use this driver as a module if you need 80 * to change the fifo mode after the kernel boots. 81 * 82 * Gadget drivers normally ignore endpoints they don't care about, and 83 * won't include them in configuration descriptors. That means only 84 * misbehaving hosts would even notice they exist. 85 */ 86 #ifdef USE_ISO 87 static unsigned fifo_mode = 3; 88 #else 89 static unsigned fifo_mode; 90 #endif 91 92 /* "modprobe omap_udc fifo_mode=42", or else as a kernel 93 * boot parameter "omap_udc:fifo_mode=42" 94 */ 95 module_param(fifo_mode, uint, 0); 96 MODULE_PARM_DESC(fifo_mode, "endpoint configuration"); 97 98 #ifdef USE_DMA 99 static bool use_dma = 1; 100 101 /* "modprobe omap_udc use_dma=y", or else as a kernel 102 * boot parameter "omap_udc:use_dma=y" 103 */ 104 module_param(use_dma, bool, 0); 105 MODULE_PARM_DESC(use_dma, "enable/disable DMA"); 106 #else /* !USE_DMA */ 107 108 /* save a bit of code */ 109 #define use_dma 0 110 #endif /* !USE_DMA */ 111 112 113 static const char driver_name[] = "omap_udc"; 114 static const char driver_desc[] = DRIVER_DESC; 115 116 /*-------------------------------------------------------------------------*/ 117 118 /* there's a notion of "current endpoint" for modifying endpoint 119 * state, and PIO access to its FIFO. 120 */ 121 122 static void use_ep(struct omap_ep *ep, u16 select) 123 { 124 u16 num = ep->bEndpointAddress & 0x0f; 125 126 if (ep->bEndpointAddress & USB_DIR_IN) 127 num |= UDC_EP_DIR; 128 omap_writew(num | select, UDC_EP_NUM); 129 /* when select, MUST deselect later !! */ 130 } 131 132 static inline void deselect_ep(void) 133 { 134 u16 w; 135 136 w = omap_readw(UDC_EP_NUM); 137 w &= ~UDC_EP_SEL; 138 omap_writew(w, UDC_EP_NUM); 139 /* 6 wait states before TX will happen */ 140 } 141 142 static void dma_channel_claim(struct omap_ep *ep, unsigned preferred); 143 144 /*-------------------------------------------------------------------------*/ 145 146 static int omap_ep_enable(struct usb_ep *_ep, 147 const struct usb_endpoint_descriptor *desc) 148 { 149 struct omap_ep *ep = container_of(_ep, struct omap_ep, ep); 150 struct omap_udc *udc; 151 unsigned long flags; 152 u16 maxp; 153 154 /* catch various bogus parameters */ 155 if (!_ep || !desc 156 || desc->bDescriptorType != USB_DT_ENDPOINT 157 || ep->bEndpointAddress != desc->bEndpointAddress 158 || ep->maxpacket < usb_endpoint_maxp(desc)) { 159 DBG("%s, bad ep or descriptor\n", __func__); 160 return -EINVAL; 161 } 162 maxp = usb_endpoint_maxp(desc); 163 if ((desc->bmAttributes == USB_ENDPOINT_XFER_BULK 164 && maxp != ep->maxpacket) 165 || usb_endpoint_maxp(desc) > ep->maxpacket 166 || !desc->wMaxPacketSize) { 167 DBG("%s, bad %s maxpacket\n", __func__, _ep->name); 168 return -ERANGE; 169 } 170 171 #ifdef USE_ISO 172 if ((desc->bmAttributes == USB_ENDPOINT_XFER_ISOC 173 && desc->bInterval != 1)) { 174 /* hardware wants period = 1; USB allows 2^(Interval-1) */ 175 DBG("%s, unsupported ISO period %dms\n", _ep->name, 176 1 << (desc->bInterval - 1)); 177 return -EDOM; 178 } 179 #else 180 if (desc->bmAttributes == USB_ENDPOINT_XFER_ISOC) { 181 DBG("%s, ISO nyet\n", _ep->name); 182 return -EDOM; 183 } 184 #endif 185 186 /* xfer types must match, except that interrupt ~= bulk */ 187 if (ep->bmAttributes != desc->bmAttributes 188 && ep->bmAttributes != USB_ENDPOINT_XFER_BULK 189 && desc->bmAttributes != USB_ENDPOINT_XFER_INT) { 190 DBG("%s, %s type mismatch\n", __func__, _ep->name); 191 return -EINVAL; 192 } 193 194 udc = ep->udc; 195 if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN) { 196 DBG("%s, bogus device state\n", __func__); 197 return -ESHUTDOWN; 198 } 199 200 spin_lock_irqsave(&udc->lock, flags); 201 202 ep->ep.desc = desc; 203 ep->irqs = 0; 204 ep->stopped = 0; 205 ep->ep.maxpacket = maxp; 206 207 /* set endpoint to initial state */ 208 ep->dma_channel = 0; 209 ep->has_dma = 0; 210 ep->lch = -1; 211 use_ep(ep, UDC_EP_SEL); 212 omap_writew(udc->clr_halt, UDC_CTRL); 213 ep->ackwait = 0; 214 deselect_ep(); 215 216 if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) 217 list_add(&ep->iso, &udc->iso); 218 219 /* maybe assign a DMA channel to this endpoint */ 220 if (use_dma && desc->bmAttributes == USB_ENDPOINT_XFER_BULK) 221 /* FIXME ISO can dma, but prefers first channel */ 222 dma_channel_claim(ep, 0); 223 224 /* PIO OUT may RX packets */ 225 if (desc->bmAttributes != USB_ENDPOINT_XFER_ISOC 226 && !ep->has_dma 227 && !(ep->bEndpointAddress & USB_DIR_IN)) { 228 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 229 ep->ackwait = 1 + ep->double_buf; 230 } 231 232 spin_unlock_irqrestore(&udc->lock, flags); 233 VDBG("%s enabled\n", _ep->name); 234 return 0; 235 } 236 237 static void nuke(struct omap_ep *, int status); 238 239 static int omap_ep_disable(struct usb_ep *_ep) 240 { 241 struct omap_ep *ep = container_of(_ep, struct omap_ep, ep); 242 unsigned long flags; 243 244 if (!_ep || !ep->ep.desc) { 245 DBG("%s, %s not enabled\n", __func__, 246 _ep ? ep->ep.name : NULL); 247 return -EINVAL; 248 } 249 250 spin_lock_irqsave(&ep->udc->lock, flags); 251 ep->ep.desc = NULL; 252 nuke(ep, -ESHUTDOWN); 253 ep->ep.maxpacket = ep->maxpacket; 254 ep->has_dma = 0; 255 omap_writew(UDC_SET_HALT, UDC_CTRL); 256 list_del_init(&ep->iso); 257 del_timer(&ep->timer); 258 259 spin_unlock_irqrestore(&ep->udc->lock, flags); 260 261 VDBG("%s disabled\n", _ep->name); 262 return 0; 263 } 264 265 /*-------------------------------------------------------------------------*/ 266 267 static struct usb_request * 268 omap_alloc_request(struct usb_ep *ep, gfp_t gfp_flags) 269 { 270 struct omap_req *req; 271 272 req = kzalloc(sizeof(*req), gfp_flags); 273 if (!req) 274 return NULL; 275 276 INIT_LIST_HEAD(&req->queue); 277 278 return &req->req; 279 } 280 281 static void 282 omap_free_request(struct usb_ep *ep, struct usb_request *_req) 283 { 284 struct omap_req *req = container_of(_req, struct omap_req, req); 285 286 kfree(req); 287 } 288 289 /*-------------------------------------------------------------------------*/ 290 291 static void 292 done(struct omap_ep *ep, struct omap_req *req, int status) 293 { 294 struct omap_udc *udc = ep->udc; 295 unsigned stopped = ep->stopped; 296 297 list_del_init(&req->queue); 298 299 if (req->req.status == -EINPROGRESS) 300 req->req.status = status; 301 else 302 status = req->req.status; 303 304 if (use_dma && ep->has_dma) 305 usb_gadget_unmap_request(&udc->gadget, &req->req, 306 (ep->bEndpointAddress & USB_DIR_IN)); 307 308 #ifndef USB_TRACE 309 if (status && status != -ESHUTDOWN) 310 #endif 311 VDBG("complete %s req %p stat %d len %u/%u\n", 312 ep->ep.name, &req->req, status, 313 req->req.actual, req->req.length); 314 315 /* don't modify queue heads during completion callback */ 316 ep->stopped = 1; 317 spin_unlock(&ep->udc->lock); 318 usb_gadget_giveback_request(&ep->ep, &req->req); 319 spin_lock(&ep->udc->lock); 320 ep->stopped = stopped; 321 } 322 323 /*-------------------------------------------------------------------------*/ 324 325 #define UDC_FIFO_FULL (UDC_NON_ISO_FIFO_FULL | UDC_ISO_FIFO_FULL) 326 #define UDC_FIFO_UNWRITABLE (UDC_EP_HALTED | UDC_FIFO_FULL) 327 328 #define FIFO_EMPTY (UDC_NON_ISO_FIFO_EMPTY | UDC_ISO_FIFO_EMPTY) 329 #define FIFO_UNREADABLE (UDC_EP_HALTED | FIFO_EMPTY) 330 331 static inline int 332 write_packet(u8 *buf, struct omap_req *req, unsigned max) 333 { 334 unsigned len; 335 u16 *wp; 336 337 len = min(req->req.length - req->req.actual, max); 338 req->req.actual += len; 339 340 max = len; 341 if (likely((((int)buf) & 1) == 0)) { 342 wp = (u16 *)buf; 343 while (max >= 2) { 344 omap_writew(*wp++, UDC_DATA); 345 max -= 2; 346 } 347 buf = (u8 *)wp; 348 } 349 while (max--) 350 omap_writeb(*buf++, UDC_DATA); 351 return len; 352 } 353 354 /* FIXME change r/w fifo calling convention */ 355 356 357 /* return: 0 = still running, 1 = completed, negative = errno */ 358 static int write_fifo(struct omap_ep *ep, struct omap_req *req) 359 { 360 u8 *buf; 361 unsigned count; 362 int is_last; 363 u16 ep_stat; 364 365 buf = req->req.buf + req->req.actual; 366 prefetch(buf); 367 368 /* PIO-IN isn't double buffered except for iso */ 369 ep_stat = omap_readw(UDC_STAT_FLG); 370 if (ep_stat & UDC_FIFO_UNWRITABLE) 371 return 0; 372 373 count = ep->ep.maxpacket; 374 count = write_packet(buf, req, count); 375 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 376 ep->ackwait = 1; 377 378 /* last packet is often short (sometimes a zlp) */ 379 if (count != ep->ep.maxpacket) 380 is_last = 1; 381 else if (req->req.length == req->req.actual 382 && !req->req.zero) 383 is_last = 1; 384 else 385 is_last = 0; 386 387 /* NOTE: requests complete when all IN data is in a 388 * FIFO (or sometimes later, if a zlp was needed). 389 * Use usb_ep_fifo_status() where needed. 390 */ 391 if (is_last) 392 done(ep, req, 0); 393 return is_last; 394 } 395 396 static inline int 397 read_packet(u8 *buf, struct omap_req *req, unsigned avail) 398 { 399 unsigned len; 400 u16 *wp; 401 402 len = min(req->req.length - req->req.actual, avail); 403 req->req.actual += len; 404 avail = len; 405 406 if (likely((((int)buf) & 1) == 0)) { 407 wp = (u16 *)buf; 408 while (avail >= 2) { 409 *wp++ = omap_readw(UDC_DATA); 410 avail -= 2; 411 } 412 buf = (u8 *)wp; 413 } 414 while (avail--) 415 *buf++ = omap_readb(UDC_DATA); 416 return len; 417 } 418 419 /* return: 0 = still running, 1 = queue empty, negative = errno */ 420 static int read_fifo(struct omap_ep *ep, struct omap_req *req) 421 { 422 u8 *buf; 423 unsigned count, avail; 424 int is_last; 425 426 buf = req->req.buf + req->req.actual; 427 prefetchw(buf); 428 429 for (;;) { 430 u16 ep_stat = omap_readw(UDC_STAT_FLG); 431 432 is_last = 0; 433 if (ep_stat & FIFO_EMPTY) { 434 if (!ep->double_buf) 435 break; 436 ep->fnf = 1; 437 } 438 if (ep_stat & UDC_EP_HALTED) 439 break; 440 441 if (ep_stat & UDC_FIFO_FULL) 442 avail = ep->ep.maxpacket; 443 else { 444 avail = omap_readw(UDC_RXFSTAT); 445 ep->fnf = ep->double_buf; 446 } 447 count = read_packet(buf, req, avail); 448 449 /* partial packet reads may not be errors */ 450 if (count < ep->ep.maxpacket) { 451 is_last = 1; 452 /* overflowed this request? flush extra data */ 453 if (count != avail) { 454 req->req.status = -EOVERFLOW; 455 avail -= count; 456 while (avail--) 457 omap_readw(UDC_DATA); 458 } 459 } else if (req->req.length == req->req.actual) 460 is_last = 1; 461 else 462 is_last = 0; 463 464 if (!ep->bEndpointAddress) 465 break; 466 if (is_last) 467 done(ep, req, 0); 468 break; 469 } 470 return is_last; 471 } 472 473 /*-------------------------------------------------------------------------*/ 474 475 static u16 dma_src_len(struct omap_ep *ep, dma_addr_t start) 476 { 477 dma_addr_t end; 478 479 /* IN-DMA needs this on fault/cancel paths, so 15xx misreports 480 * the last transfer's bytecount by more than a FIFO's worth. 481 */ 482 if (cpu_is_omap15xx()) 483 return 0; 484 485 end = omap_get_dma_src_pos(ep->lch); 486 if (end == ep->dma_counter) 487 return 0; 488 489 end |= start & (0xffff << 16); 490 if (end < start) 491 end += 0x10000; 492 return end - start; 493 } 494 495 static u16 dma_dest_len(struct omap_ep *ep, dma_addr_t start) 496 { 497 dma_addr_t end; 498 499 end = omap_get_dma_dst_pos(ep->lch); 500 if (end == ep->dma_counter) 501 return 0; 502 503 end |= start & (0xffff << 16); 504 if (cpu_is_omap15xx()) 505 end++; 506 if (end < start) 507 end += 0x10000; 508 return end - start; 509 } 510 511 512 /* Each USB transfer request using DMA maps to one or more DMA transfers. 513 * When DMA completion isn't request completion, the UDC continues with 514 * the next DMA transfer for that USB transfer. 515 */ 516 517 static void next_in_dma(struct omap_ep *ep, struct omap_req *req) 518 { 519 u16 txdma_ctrl, w; 520 unsigned length = req->req.length - req->req.actual; 521 const int sync_mode = cpu_is_omap15xx() 522 ? OMAP_DMA_SYNC_FRAME 523 : OMAP_DMA_SYNC_ELEMENT; 524 int dma_trigger = 0; 525 526 /* measure length in either bytes or packets */ 527 if ((cpu_is_omap16xx() && length <= UDC_TXN_TSC) 528 || (cpu_is_omap15xx() && length < ep->maxpacket)) { 529 txdma_ctrl = UDC_TXN_EOT | length; 530 omap_set_dma_transfer_params(ep->lch, OMAP_DMA_DATA_TYPE_S8, 531 length, 1, sync_mode, dma_trigger, 0); 532 } else { 533 length = min(length / ep->maxpacket, 534 (unsigned) UDC_TXN_TSC + 1); 535 txdma_ctrl = length; 536 omap_set_dma_transfer_params(ep->lch, OMAP_DMA_DATA_TYPE_S16, 537 ep->ep.maxpacket >> 1, length, sync_mode, 538 dma_trigger, 0); 539 length *= ep->maxpacket; 540 } 541 omap_set_dma_src_params(ep->lch, OMAP_DMA_PORT_EMIFF, 542 OMAP_DMA_AMODE_POST_INC, req->req.dma + req->req.actual, 543 0, 0); 544 545 omap_start_dma(ep->lch); 546 ep->dma_counter = omap_get_dma_src_pos(ep->lch); 547 w = omap_readw(UDC_DMA_IRQ_EN); 548 w |= UDC_TX_DONE_IE(ep->dma_channel); 549 omap_writew(w, UDC_DMA_IRQ_EN); 550 omap_writew(UDC_TXN_START | txdma_ctrl, UDC_TXDMA(ep->dma_channel)); 551 req->dma_bytes = length; 552 } 553 554 static void finish_in_dma(struct omap_ep *ep, struct omap_req *req, int status) 555 { 556 u16 w; 557 558 if (status == 0) { 559 req->req.actual += req->dma_bytes; 560 561 /* return if this request needs to send data or zlp */ 562 if (req->req.actual < req->req.length) 563 return; 564 if (req->req.zero 565 && req->dma_bytes != 0 566 && (req->req.actual % ep->maxpacket) == 0) 567 return; 568 } else 569 req->req.actual += dma_src_len(ep, req->req.dma 570 + req->req.actual); 571 572 /* tx completion */ 573 omap_stop_dma(ep->lch); 574 w = omap_readw(UDC_DMA_IRQ_EN); 575 w &= ~UDC_TX_DONE_IE(ep->dma_channel); 576 omap_writew(w, UDC_DMA_IRQ_EN); 577 done(ep, req, status); 578 } 579 580 static void next_out_dma(struct omap_ep *ep, struct omap_req *req) 581 { 582 unsigned packets = req->req.length - req->req.actual; 583 int dma_trigger = 0; 584 u16 w; 585 586 /* set up this DMA transfer, enable the fifo, start */ 587 packets /= ep->ep.maxpacket; 588 packets = min(packets, (unsigned)UDC_RXN_TC + 1); 589 req->dma_bytes = packets * ep->ep.maxpacket; 590 omap_set_dma_transfer_params(ep->lch, OMAP_DMA_DATA_TYPE_S16, 591 ep->ep.maxpacket >> 1, packets, 592 OMAP_DMA_SYNC_ELEMENT, 593 dma_trigger, 0); 594 omap_set_dma_dest_params(ep->lch, OMAP_DMA_PORT_EMIFF, 595 OMAP_DMA_AMODE_POST_INC, req->req.dma + req->req.actual, 596 0, 0); 597 ep->dma_counter = omap_get_dma_dst_pos(ep->lch); 598 599 omap_writew(UDC_RXN_STOP | (packets - 1), UDC_RXDMA(ep->dma_channel)); 600 w = omap_readw(UDC_DMA_IRQ_EN); 601 w |= UDC_RX_EOT_IE(ep->dma_channel); 602 omap_writew(w, UDC_DMA_IRQ_EN); 603 omap_writew(ep->bEndpointAddress & 0xf, UDC_EP_NUM); 604 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 605 606 omap_start_dma(ep->lch); 607 } 608 609 static void 610 finish_out_dma(struct omap_ep *ep, struct omap_req *req, int status, int one) 611 { 612 u16 count, w; 613 614 if (status == 0) 615 ep->dma_counter = (u16) (req->req.dma + req->req.actual); 616 count = dma_dest_len(ep, req->req.dma + req->req.actual); 617 count += req->req.actual; 618 if (one) 619 count--; 620 if (count <= req->req.length) 621 req->req.actual = count; 622 623 if (count != req->dma_bytes || status) 624 omap_stop_dma(ep->lch); 625 626 /* if this wasn't short, request may need another transfer */ 627 else if (req->req.actual < req->req.length) 628 return; 629 630 /* rx completion */ 631 w = omap_readw(UDC_DMA_IRQ_EN); 632 w &= ~UDC_RX_EOT_IE(ep->dma_channel); 633 omap_writew(w, UDC_DMA_IRQ_EN); 634 done(ep, req, status); 635 } 636 637 static void dma_irq(struct omap_udc *udc, u16 irq_src) 638 { 639 u16 dman_stat = omap_readw(UDC_DMAN_STAT); 640 struct omap_ep *ep; 641 struct omap_req *req; 642 643 /* IN dma: tx to host */ 644 if (irq_src & UDC_TXN_DONE) { 645 ep = &udc->ep[16 + UDC_DMA_TX_SRC(dman_stat)]; 646 ep->irqs++; 647 /* can see TXN_DONE after dma abort */ 648 if (!list_empty(&ep->queue)) { 649 req = container_of(ep->queue.next, 650 struct omap_req, queue); 651 finish_in_dma(ep, req, 0); 652 } 653 omap_writew(UDC_TXN_DONE, UDC_IRQ_SRC); 654 655 if (!list_empty(&ep->queue)) { 656 req = container_of(ep->queue.next, 657 struct omap_req, queue); 658 next_in_dma(ep, req); 659 } 660 } 661 662 /* OUT dma: rx from host */ 663 if (irq_src & UDC_RXN_EOT) { 664 ep = &udc->ep[UDC_DMA_RX_SRC(dman_stat)]; 665 ep->irqs++; 666 /* can see RXN_EOT after dma abort */ 667 if (!list_empty(&ep->queue)) { 668 req = container_of(ep->queue.next, 669 struct omap_req, queue); 670 finish_out_dma(ep, req, 0, dman_stat & UDC_DMA_RX_SB); 671 } 672 omap_writew(UDC_RXN_EOT, UDC_IRQ_SRC); 673 674 if (!list_empty(&ep->queue)) { 675 req = container_of(ep->queue.next, 676 struct omap_req, queue); 677 next_out_dma(ep, req); 678 } 679 } 680 681 if (irq_src & UDC_RXN_CNT) { 682 ep = &udc->ep[UDC_DMA_RX_SRC(dman_stat)]; 683 ep->irqs++; 684 /* omap15xx does this unasked... */ 685 VDBG("%s, RX_CNT irq?\n", ep->ep.name); 686 omap_writew(UDC_RXN_CNT, UDC_IRQ_SRC); 687 } 688 } 689 690 static void dma_error(int lch, u16 ch_status, void *data) 691 { 692 struct omap_ep *ep = data; 693 694 /* if ch_status & OMAP_DMA_DROP_IRQ ... */ 695 /* if ch_status & OMAP1_DMA_TOUT_IRQ ... */ 696 ERR("%s dma error, lch %d status %02x\n", ep->ep.name, lch, ch_status); 697 698 /* complete current transfer ... */ 699 } 700 701 static void dma_channel_claim(struct omap_ep *ep, unsigned channel) 702 { 703 u16 reg; 704 int status, restart, is_in; 705 int dma_channel; 706 707 is_in = ep->bEndpointAddress & USB_DIR_IN; 708 if (is_in) 709 reg = omap_readw(UDC_TXDMA_CFG); 710 else 711 reg = omap_readw(UDC_RXDMA_CFG); 712 reg |= UDC_DMA_REQ; /* "pulse" activated */ 713 714 ep->dma_channel = 0; 715 ep->lch = -1; 716 if (channel == 0 || channel > 3) { 717 if ((reg & 0x0f00) == 0) 718 channel = 3; 719 else if ((reg & 0x00f0) == 0) 720 channel = 2; 721 else if ((reg & 0x000f) == 0) /* preferred for ISO */ 722 channel = 1; 723 else { 724 status = -EMLINK; 725 goto just_restart; 726 } 727 } 728 reg |= (0x0f & ep->bEndpointAddress) << (4 * (channel - 1)); 729 ep->dma_channel = channel; 730 731 if (is_in) { 732 dma_channel = OMAP_DMA_USB_W2FC_TX0 - 1 + channel; 733 status = omap_request_dma(dma_channel, 734 ep->ep.name, dma_error, ep, &ep->lch); 735 if (status == 0) { 736 omap_writew(reg, UDC_TXDMA_CFG); 737 /* EMIFF or SDRC */ 738 omap_set_dma_src_burst_mode(ep->lch, 739 OMAP_DMA_DATA_BURST_4); 740 omap_set_dma_src_data_pack(ep->lch, 1); 741 /* TIPB */ 742 omap_set_dma_dest_params(ep->lch, 743 OMAP_DMA_PORT_TIPB, 744 OMAP_DMA_AMODE_CONSTANT, 745 UDC_DATA_DMA, 746 0, 0); 747 } 748 } else { 749 dma_channel = OMAP_DMA_USB_W2FC_RX0 - 1 + channel; 750 status = omap_request_dma(dma_channel, 751 ep->ep.name, dma_error, ep, &ep->lch); 752 if (status == 0) { 753 omap_writew(reg, UDC_RXDMA_CFG); 754 /* TIPB */ 755 omap_set_dma_src_params(ep->lch, 756 OMAP_DMA_PORT_TIPB, 757 OMAP_DMA_AMODE_CONSTANT, 758 UDC_DATA_DMA, 759 0, 0); 760 /* EMIFF or SDRC */ 761 omap_set_dma_dest_burst_mode(ep->lch, 762 OMAP_DMA_DATA_BURST_4); 763 omap_set_dma_dest_data_pack(ep->lch, 1); 764 } 765 } 766 if (status) 767 ep->dma_channel = 0; 768 else { 769 ep->has_dma = 1; 770 omap_disable_dma_irq(ep->lch, OMAP_DMA_BLOCK_IRQ); 771 772 /* channel type P: hw synch (fifo) */ 773 if (!cpu_is_omap15xx()) 774 omap_set_dma_channel_mode(ep->lch, OMAP_DMA_LCH_P); 775 } 776 777 just_restart: 778 /* restart any queue, even if the claim failed */ 779 restart = !ep->stopped && !list_empty(&ep->queue); 780 781 if (status) 782 DBG("%s no dma channel: %d%s\n", ep->ep.name, status, 783 restart ? " (restart)" : ""); 784 else 785 DBG("%s claimed %cxdma%d lch %d%s\n", ep->ep.name, 786 is_in ? 't' : 'r', 787 ep->dma_channel - 1, ep->lch, 788 restart ? " (restart)" : ""); 789 790 if (restart) { 791 struct omap_req *req; 792 req = container_of(ep->queue.next, struct omap_req, queue); 793 if (ep->has_dma) 794 (is_in ? next_in_dma : next_out_dma)(ep, req); 795 else { 796 use_ep(ep, UDC_EP_SEL); 797 (is_in ? write_fifo : read_fifo)(ep, req); 798 deselect_ep(); 799 if (!is_in) { 800 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 801 ep->ackwait = 1 + ep->double_buf; 802 } 803 /* IN: 6 wait states before it'll tx */ 804 } 805 } 806 } 807 808 static void dma_channel_release(struct omap_ep *ep) 809 { 810 int shift = 4 * (ep->dma_channel - 1); 811 u16 mask = 0x0f << shift; 812 struct omap_req *req; 813 int active; 814 815 /* abort any active usb transfer request */ 816 if (!list_empty(&ep->queue)) 817 req = container_of(ep->queue.next, struct omap_req, queue); 818 else 819 req = NULL; 820 821 active = omap_get_dma_active_status(ep->lch); 822 823 DBG("%s release %s %cxdma%d %p\n", ep->ep.name, 824 active ? "active" : "idle", 825 (ep->bEndpointAddress & USB_DIR_IN) ? 't' : 'r', 826 ep->dma_channel - 1, req); 827 828 /* NOTE: re-setting RX_REQ/TX_REQ because of a chip bug (before 829 * OMAP 1710 ES2.0) where reading the DMA_CFG can clear them. 830 */ 831 832 /* wait till current packet DMA finishes, and fifo empties */ 833 if (ep->bEndpointAddress & USB_DIR_IN) { 834 omap_writew((omap_readw(UDC_TXDMA_CFG) & ~mask) | UDC_DMA_REQ, 835 UDC_TXDMA_CFG); 836 837 if (req) { 838 finish_in_dma(ep, req, -ECONNRESET); 839 840 /* clear FIFO; hosts probably won't empty it */ 841 use_ep(ep, UDC_EP_SEL); 842 omap_writew(UDC_CLR_EP, UDC_CTRL); 843 deselect_ep(); 844 } 845 while (omap_readw(UDC_TXDMA_CFG) & mask) 846 udelay(10); 847 } else { 848 omap_writew((omap_readw(UDC_RXDMA_CFG) & ~mask) | UDC_DMA_REQ, 849 UDC_RXDMA_CFG); 850 851 /* dma empties the fifo */ 852 while (omap_readw(UDC_RXDMA_CFG) & mask) 853 udelay(10); 854 if (req) 855 finish_out_dma(ep, req, -ECONNRESET, 0); 856 } 857 omap_free_dma(ep->lch); 858 ep->dma_channel = 0; 859 ep->lch = -1; 860 /* has_dma still set, till endpoint is fully quiesced */ 861 } 862 863 864 /*-------------------------------------------------------------------------*/ 865 866 static int 867 omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) 868 { 869 struct omap_ep *ep = container_of(_ep, struct omap_ep, ep); 870 struct omap_req *req = container_of(_req, struct omap_req, req); 871 struct omap_udc *udc; 872 unsigned long flags; 873 int is_iso = 0; 874 875 /* catch various bogus parameters */ 876 if (!_req || !req->req.complete || !req->req.buf 877 || !list_empty(&req->queue)) { 878 DBG("%s, bad params\n", __func__); 879 return -EINVAL; 880 } 881 if (!_ep || (!ep->ep.desc && ep->bEndpointAddress)) { 882 DBG("%s, bad ep\n", __func__); 883 return -EINVAL; 884 } 885 if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) { 886 if (req->req.length > ep->ep.maxpacket) 887 return -EMSGSIZE; 888 is_iso = 1; 889 } 890 891 /* this isn't bogus, but OMAP DMA isn't the only hardware to 892 * have a hard time with partial packet reads... reject it. 893 */ 894 if (use_dma 895 && ep->has_dma 896 && ep->bEndpointAddress != 0 897 && (ep->bEndpointAddress & USB_DIR_IN) == 0 898 && (req->req.length % ep->ep.maxpacket) != 0) { 899 DBG("%s, no partial packet OUT reads\n", __func__); 900 return -EMSGSIZE; 901 } 902 903 udc = ep->udc; 904 if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN) 905 return -ESHUTDOWN; 906 907 if (use_dma && ep->has_dma) 908 usb_gadget_map_request(&udc->gadget, &req->req, 909 (ep->bEndpointAddress & USB_DIR_IN)); 910 911 VDBG("%s queue req %p, len %d buf %p\n", 912 ep->ep.name, _req, _req->length, _req->buf); 913 914 spin_lock_irqsave(&udc->lock, flags); 915 916 req->req.status = -EINPROGRESS; 917 req->req.actual = 0; 918 919 /* maybe kickstart non-iso i/o queues */ 920 if (is_iso) { 921 u16 w; 922 923 w = omap_readw(UDC_IRQ_EN); 924 w |= UDC_SOF_IE; 925 omap_writew(w, UDC_IRQ_EN); 926 } else if (list_empty(&ep->queue) && !ep->stopped && !ep->ackwait) { 927 int is_in; 928 929 if (ep->bEndpointAddress == 0) { 930 if (!udc->ep0_pending || !list_empty(&ep->queue)) { 931 spin_unlock_irqrestore(&udc->lock, flags); 932 return -EL2HLT; 933 } 934 935 /* empty DATA stage? */ 936 is_in = udc->ep0_in; 937 if (!req->req.length) { 938 939 /* chip became CONFIGURED or ADDRESSED 940 * earlier; drivers may already have queued 941 * requests to non-control endpoints 942 */ 943 if (udc->ep0_set_config) { 944 u16 irq_en = omap_readw(UDC_IRQ_EN); 945 946 irq_en |= UDC_DS_CHG_IE | UDC_EP0_IE; 947 if (!udc->ep0_reset_config) 948 irq_en |= UDC_EPN_RX_IE 949 | UDC_EPN_TX_IE; 950 omap_writew(irq_en, UDC_IRQ_EN); 951 } 952 953 /* STATUS for zero length DATA stages is 954 * always an IN ... even for IN transfers, 955 * a weird case which seem to stall OMAP. 956 */ 957 omap_writew(UDC_EP_SEL | UDC_EP_DIR, 958 UDC_EP_NUM); 959 omap_writew(UDC_CLR_EP, UDC_CTRL); 960 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 961 omap_writew(UDC_EP_DIR, UDC_EP_NUM); 962 963 /* cleanup */ 964 udc->ep0_pending = 0; 965 done(ep, req, 0); 966 req = NULL; 967 968 /* non-empty DATA stage */ 969 } else if (is_in) { 970 omap_writew(UDC_EP_SEL | UDC_EP_DIR, 971 UDC_EP_NUM); 972 } else { 973 if (udc->ep0_setup) 974 goto irq_wait; 975 omap_writew(UDC_EP_SEL, UDC_EP_NUM); 976 } 977 } else { 978 is_in = ep->bEndpointAddress & USB_DIR_IN; 979 if (!ep->has_dma) 980 use_ep(ep, UDC_EP_SEL); 981 /* if ISO: SOF IRQs must be enabled/disabled! */ 982 } 983 984 if (ep->has_dma) 985 (is_in ? next_in_dma : next_out_dma)(ep, req); 986 else if (req) { 987 if ((is_in ? write_fifo : read_fifo)(ep, req) == 1) 988 req = NULL; 989 deselect_ep(); 990 if (!is_in) { 991 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 992 ep->ackwait = 1 + ep->double_buf; 993 } 994 /* IN: 6 wait states before it'll tx */ 995 } 996 } 997 998 irq_wait: 999 /* irq handler advances the queue */ 1000 if (req != NULL) 1001 list_add_tail(&req->queue, &ep->queue); 1002 spin_unlock_irqrestore(&udc->lock, flags); 1003 1004 return 0; 1005 } 1006 1007 static int omap_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req) 1008 { 1009 struct omap_ep *ep = container_of(_ep, struct omap_ep, ep); 1010 struct omap_req *req; 1011 unsigned long flags; 1012 1013 if (!_ep || !_req) 1014 return -EINVAL; 1015 1016 spin_lock_irqsave(&ep->udc->lock, flags); 1017 1018 /* make sure it's actually queued on this endpoint */ 1019 list_for_each_entry(req, &ep->queue, queue) { 1020 if (&req->req == _req) 1021 break; 1022 } 1023 if (&req->req != _req) { 1024 spin_unlock_irqrestore(&ep->udc->lock, flags); 1025 return -EINVAL; 1026 } 1027 1028 if (use_dma && ep->dma_channel && ep->queue.next == &req->queue) { 1029 int channel = ep->dma_channel; 1030 1031 /* releasing the channel cancels the request, 1032 * reclaiming the channel restarts the queue 1033 */ 1034 dma_channel_release(ep); 1035 dma_channel_claim(ep, channel); 1036 } else 1037 done(ep, req, -ECONNRESET); 1038 spin_unlock_irqrestore(&ep->udc->lock, flags); 1039 return 0; 1040 } 1041 1042 /*-------------------------------------------------------------------------*/ 1043 1044 static int omap_ep_set_halt(struct usb_ep *_ep, int value) 1045 { 1046 struct omap_ep *ep = container_of(_ep, struct omap_ep, ep); 1047 unsigned long flags; 1048 int status = -EOPNOTSUPP; 1049 1050 spin_lock_irqsave(&ep->udc->lock, flags); 1051 1052 /* just use protocol stalls for ep0; real halts are annoying */ 1053 if (ep->bEndpointAddress == 0) { 1054 if (!ep->udc->ep0_pending) 1055 status = -EINVAL; 1056 else if (value) { 1057 if (ep->udc->ep0_set_config) { 1058 WARNING("error changing config?\n"); 1059 omap_writew(UDC_CLR_CFG, UDC_SYSCON2); 1060 } 1061 omap_writew(UDC_STALL_CMD, UDC_SYSCON2); 1062 ep->udc->ep0_pending = 0; 1063 status = 0; 1064 } else /* NOP */ 1065 status = 0; 1066 1067 /* otherwise, all active non-ISO endpoints can halt */ 1068 } else if (ep->bmAttributes != USB_ENDPOINT_XFER_ISOC && ep->ep.desc) { 1069 1070 /* IN endpoints must already be idle */ 1071 if ((ep->bEndpointAddress & USB_DIR_IN) 1072 && !list_empty(&ep->queue)) { 1073 status = -EAGAIN; 1074 goto done; 1075 } 1076 1077 if (value) { 1078 int channel; 1079 1080 if (use_dma && ep->dma_channel 1081 && !list_empty(&ep->queue)) { 1082 channel = ep->dma_channel; 1083 dma_channel_release(ep); 1084 } else 1085 channel = 0; 1086 1087 use_ep(ep, UDC_EP_SEL); 1088 if (omap_readw(UDC_STAT_FLG) & UDC_NON_ISO_FIFO_EMPTY) { 1089 omap_writew(UDC_SET_HALT, UDC_CTRL); 1090 status = 0; 1091 } else 1092 status = -EAGAIN; 1093 deselect_ep(); 1094 1095 if (channel) 1096 dma_channel_claim(ep, channel); 1097 } else { 1098 use_ep(ep, 0); 1099 omap_writew(ep->udc->clr_halt, UDC_CTRL); 1100 ep->ackwait = 0; 1101 if (!(ep->bEndpointAddress & USB_DIR_IN)) { 1102 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 1103 ep->ackwait = 1 + ep->double_buf; 1104 } 1105 } 1106 } 1107 done: 1108 VDBG("%s %s halt stat %d\n", ep->ep.name, 1109 value ? "set" : "clear", status); 1110 1111 spin_unlock_irqrestore(&ep->udc->lock, flags); 1112 return status; 1113 } 1114 1115 static struct usb_ep_ops omap_ep_ops = { 1116 .enable = omap_ep_enable, 1117 .disable = omap_ep_disable, 1118 1119 .alloc_request = omap_alloc_request, 1120 .free_request = omap_free_request, 1121 1122 .queue = omap_ep_queue, 1123 .dequeue = omap_ep_dequeue, 1124 1125 .set_halt = omap_ep_set_halt, 1126 /* fifo_status ... report bytes in fifo */ 1127 /* fifo_flush ... flush fifo */ 1128 }; 1129 1130 /*-------------------------------------------------------------------------*/ 1131 1132 static int omap_get_frame(struct usb_gadget *gadget) 1133 { 1134 u16 sof = omap_readw(UDC_SOF); 1135 return (sof & UDC_TS_OK) ? (sof & UDC_TS) : -EL2NSYNC; 1136 } 1137 1138 static int omap_wakeup(struct usb_gadget *gadget) 1139 { 1140 struct omap_udc *udc; 1141 unsigned long flags; 1142 int retval = -EHOSTUNREACH; 1143 1144 udc = container_of(gadget, struct omap_udc, gadget); 1145 1146 spin_lock_irqsave(&udc->lock, flags); 1147 if (udc->devstat & UDC_SUS) { 1148 /* NOTE: OTG spec erratum says that OTG devices may 1149 * issue wakeups without host enable. 1150 */ 1151 if (udc->devstat & (UDC_B_HNP_ENABLE|UDC_R_WK_OK)) { 1152 DBG("remote wakeup...\n"); 1153 omap_writew(UDC_RMT_WKP, UDC_SYSCON2); 1154 retval = 0; 1155 } 1156 1157 /* NOTE: non-OTG systems may use SRP TOO... */ 1158 } else if (!(udc->devstat & UDC_ATT)) { 1159 if (!IS_ERR_OR_NULL(udc->transceiver)) 1160 retval = otg_start_srp(udc->transceiver->otg); 1161 } 1162 spin_unlock_irqrestore(&udc->lock, flags); 1163 1164 return retval; 1165 } 1166 1167 static int 1168 omap_set_selfpowered(struct usb_gadget *gadget, int is_selfpowered) 1169 { 1170 struct omap_udc *udc; 1171 unsigned long flags; 1172 u16 syscon1; 1173 1174 udc = container_of(gadget, struct omap_udc, gadget); 1175 spin_lock_irqsave(&udc->lock, flags); 1176 syscon1 = omap_readw(UDC_SYSCON1); 1177 if (is_selfpowered) 1178 syscon1 |= UDC_SELF_PWR; 1179 else 1180 syscon1 &= ~UDC_SELF_PWR; 1181 omap_writew(syscon1, UDC_SYSCON1); 1182 spin_unlock_irqrestore(&udc->lock, flags); 1183 1184 return 0; 1185 } 1186 1187 static int can_pullup(struct omap_udc *udc) 1188 { 1189 return udc->driver && udc->softconnect && udc->vbus_active; 1190 } 1191 1192 static void pullup_enable(struct omap_udc *udc) 1193 { 1194 u16 w; 1195 1196 w = omap_readw(UDC_SYSCON1); 1197 w |= UDC_PULLUP_EN; 1198 omap_writew(w, UDC_SYSCON1); 1199 if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx()) { 1200 u32 l; 1201 1202 l = omap_readl(OTG_CTRL); 1203 l |= OTG_BSESSVLD; 1204 omap_writel(l, OTG_CTRL); 1205 } 1206 omap_writew(UDC_DS_CHG_IE, UDC_IRQ_EN); 1207 } 1208 1209 static void pullup_disable(struct omap_udc *udc) 1210 { 1211 u16 w; 1212 1213 if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx()) { 1214 u32 l; 1215 1216 l = omap_readl(OTG_CTRL); 1217 l &= ~OTG_BSESSVLD; 1218 omap_writel(l, OTG_CTRL); 1219 } 1220 omap_writew(UDC_DS_CHG_IE, UDC_IRQ_EN); 1221 w = omap_readw(UDC_SYSCON1); 1222 w &= ~UDC_PULLUP_EN; 1223 omap_writew(w, UDC_SYSCON1); 1224 } 1225 1226 static struct omap_udc *udc; 1227 1228 static void omap_udc_enable_clock(int enable) 1229 { 1230 if (udc == NULL || udc->dc_clk == NULL || udc->hhc_clk == NULL) 1231 return; 1232 1233 if (enable) { 1234 clk_enable(udc->dc_clk); 1235 clk_enable(udc->hhc_clk); 1236 udelay(100); 1237 } else { 1238 clk_disable(udc->hhc_clk); 1239 clk_disable(udc->dc_clk); 1240 } 1241 } 1242 1243 /* 1244 * Called by whatever detects VBUS sessions: external transceiver 1245 * driver, or maybe GPIO0 VBUS IRQ. May request 48 MHz clock. 1246 */ 1247 static int omap_vbus_session(struct usb_gadget *gadget, int is_active) 1248 { 1249 struct omap_udc *udc; 1250 unsigned long flags; 1251 u32 l; 1252 1253 udc = container_of(gadget, struct omap_udc, gadget); 1254 spin_lock_irqsave(&udc->lock, flags); 1255 VDBG("VBUS %s\n", is_active ? "on" : "off"); 1256 udc->vbus_active = (is_active != 0); 1257 if (cpu_is_omap15xx()) { 1258 /* "software" detect, ignored if !VBUS_MODE_1510 */ 1259 l = omap_readl(FUNC_MUX_CTRL_0); 1260 if (is_active) 1261 l |= VBUS_CTRL_1510; 1262 else 1263 l &= ~VBUS_CTRL_1510; 1264 omap_writel(l, FUNC_MUX_CTRL_0); 1265 } 1266 if (udc->dc_clk != NULL && is_active) { 1267 if (!udc->clk_requested) { 1268 omap_udc_enable_clock(1); 1269 udc->clk_requested = 1; 1270 } 1271 } 1272 if (can_pullup(udc)) 1273 pullup_enable(udc); 1274 else 1275 pullup_disable(udc); 1276 if (udc->dc_clk != NULL && !is_active) { 1277 if (udc->clk_requested) { 1278 omap_udc_enable_clock(0); 1279 udc->clk_requested = 0; 1280 } 1281 } 1282 spin_unlock_irqrestore(&udc->lock, flags); 1283 return 0; 1284 } 1285 1286 static int omap_vbus_draw(struct usb_gadget *gadget, unsigned mA) 1287 { 1288 struct omap_udc *udc; 1289 1290 udc = container_of(gadget, struct omap_udc, gadget); 1291 if (!IS_ERR_OR_NULL(udc->transceiver)) 1292 return usb_phy_set_power(udc->transceiver, mA); 1293 return -EOPNOTSUPP; 1294 } 1295 1296 static int omap_pullup(struct usb_gadget *gadget, int is_on) 1297 { 1298 struct omap_udc *udc; 1299 unsigned long flags; 1300 1301 udc = container_of(gadget, struct omap_udc, gadget); 1302 spin_lock_irqsave(&udc->lock, flags); 1303 udc->softconnect = (is_on != 0); 1304 if (can_pullup(udc)) 1305 pullup_enable(udc); 1306 else 1307 pullup_disable(udc); 1308 spin_unlock_irqrestore(&udc->lock, flags); 1309 return 0; 1310 } 1311 1312 static int omap_udc_start(struct usb_gadget *g, 1313 struct usb_gadget_driver *driver); 1314 static int omap_udc_stop(struct usb_gadget *g); 1315 1316 static const struct usb_gadget_ops omap_gadget_ops = { 1317 .get_frame = omap_get_frame, 1318 .wakeup = omap_wakeup, 1319 .set_selfpowered = omap_set_selfpowered, 1320 .vbus_session = omap_vbus_session, 1321 .vbus_draw = omap_vbus_draw, 1322 .pullup = omap_pullup, 1323 .udc_start = omap_udc_start, 1324 .udc_stop = omap_udc_stop, 1325 }; 1326 1327 /*-------------------------------------------------------------------------*/ 1328 1329 /* dequeue ALL requests; caller holds udc->lock */ 1330 static void nuke(struct omap_ep *ep, int status) 1331 { 1332 struct omap_req *req; 1333 1334 ep->stopped = 1; 1335 1336 if (use_dma && ep->dma_channel) 1337 dma_channel_release(ep); 1338 1339 use_ep(ep, 0); 1340 omap_writew(UDC_CLR_EP, UDC_CTRL); 1341 if (ep->bEndpointAddress && ep->bmAttributes != USB_ENDPOINT_XFER_ISOC) 1342 omap_writew(UDC_SET_HALT, UDC_CTRL); 1343 1344 while (!list_empty(&ep->queue)) { 1345 req = list_entry(ep->queue.next, struct omap_req, queue); 1346 done(ep, req, status); 1347 } 1348 } 1349 1350 /* caller holds udc->lock */ 1351 static void udc_quiesce(struct omap_udc *udc) 1352 { 1353 struct omap_ep *ep; 1354 1355 udc->gadget.speed = USB_SPEED_UNKNOWN; 1356 nuke(&udc->ep[0], -ESHUTDOWN); 1357 list_for_each_entry(ep, &udc->gadget.ep_list, ep.ep_list) 1358 nuke(ep, -ESHUTDOWN); 1359 } 1360 1361 /*-------------------------------------------------------------------------*/ 1362 1363 static void update_otg(struct omap_udc *udc) 1364 { 1365 u16 devstat; 1366 1367 if (!gadget_is_otg(&udc->gadget)) 1368 return; 1369 1370 if (omap_readl(OTG_CTRL) & OTG_ID) 1371 devstat = omap_readw(UDC_DEVSTAT); 1372 else 1373 devstat = 0; 1374 1375 udc->gadget.b_hnp_enable = !!(devstat & UDC_B_HNP_ENABLE); 1376 udc->gadget.a_hnp_support = !!(devstat & UDC_A_HNP_SUPPORT); 1377 udc->gadget.a_alt_hnp_support = !!(devstat & UDC_A_ALT_HNP_SUPPORT); 1378 1379 /* Enable HNP early, avoiding races on suspend irq path. 1380 * ASSUMES OTG state machine B_BUS_REQ input is true. 1381 */ 1382 if (udc->gadget.b_hnp_enable) { 1383 u32 l; 1384 1385 l = omap_readl(OTG_CTRL); 1386 l |= OTG_B_HNPEN | OTG_B_BUSREQ; 1387 l &= ~OTG_PULLUP; 1388 omap_writel(l, OTG_CTRL); 1389 } 1390 } 1391 1392 static void ep0_irq(struct omap_udc *udc, u16 irq_src) 1393 { 1394 struct omap_ep *ep0 = &udc->ep[0]; 1395 struct omap_req *req = NULL; 1396 1397 ep0->irqs++; 1398 1399 /* Clear any pending requests and then scrub any rx/tx state 1400 * before starting to handle the SETUP request. 1401 */ 1402 if (irq_src & UDC_SETUP) { 1403 u16 ack = irq_src & (UDC_EP0_TX|UDC_EP0_RX); 1404 1405 nuke(ep0, 0); 1406 if (ack) { 1407 omap_writew(ack, UDC_IRQ_SRC); 1408 irq_src = UDC_SETUP; 1409 } 1410 } 1411 1412 /* IN/OUT packets mean we're in the DATA or STATUS stage. 1413 * This driver uses only uses protocol stalls (ep0 never halts), 1414 * and if we got this far the gadget driver already had a 1415 * chance to stall. Tries to be forgiving of host oddities. 1416 * 1417 * NOTE: the last chance gadget drivers have to stall control 1418 * requests is during their request completion callback. 1419 */ 1420 if (!list_empty(&ep0->queue)) 1421 req = container_of(ep0->queue.next, struct omap_req, queue); 1422 1423 /* IN == TX to host */ 1424 if (irq_src & UDC_EP0_TX) { 1425 int stat; 1426 1427 omap_writew(UDC_EP0_TX, UDC_IRQ_SRC); 1428 omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM); 1429 stat = omap_readw(UDC_STAT_FLG); 1430 if (stat & UDC_ACK) { 1431 if (udc->ep0_in) { 1432 /* write next IN packet from response, 1433 * or set up the status stage. 1434 */ 1435 if (req) 1436 stat = write_fifo(ep0, req); 1437 omap_writew(UDC_EP_DIR, UDC_EP_NUM); 1438 if (!req && udc->ep0_pending) { 1439 omap_writew(UDC_EP_SEL, UDC_EP_NUM); 1440 omap_writew(UDC_CLR_EP, UDC_CTRL); 1441 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 1442 omap_writew(0, UDC_EP_NUM); 1443 udc->ep0_pending = 0; 1444 } /* else: 6 wait states before it'll tx */ 1445 } else { 1446 /* ack status stage of OUT transfer */ 1447 omap_writew(UDC_EP_DIR, UDC_EP_NUM); 1448 if (req) 1449 done(ep0, req, 0); 1450 } 1451 req = NULL; 1452 } else if (stat & UDC_STALL) { 1453 omap_writew(UDC_CLR_HALT, UDC_CTRL); 1454 omap_writew(UDC_EP_DIR, UDC_EP_NUM); 1455 } else { 1456 omap_writew(UDC_EP_DIR, UDC_EP_NUM); 1457 } 1458 } 1459 1460 /* OUT == RX from host */ 1461 if (irq_src & UDC_EP0_RX) { 1462 int stat; 1463 1464 omap_writew(UDC_EP0_RX, UDC_IRQ_SRC); 1465 omap_writew(UDC_EP_SEL, UDC_EP_NUM); 1466 stat = omap_readw(UDC_STAT_FLG); 1467 if (stat & UDC_ACK) { 1468 if (!udc->ep0_in) { 1469 stat = 0; 1470 /* read next OUT packet of request, maybe 1471 * reactiviting the fifo; stall on errors. 1472 */ 1473 stat = read_fifo(ep0, req); 1474 if (!req || stat < 0) { 1475 omap_writew(UDC_STALL_CMD, UDC_SYSCON2); 1476 udc->ep0_pending = 0; 1477 stat = 0; 1478 } else if (stat == 0) 1479 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 1480 omap_writew(0, UDC_EP_NUM); 1481 1482 /* activate status stage */ 1483 if (stat == 1) { 1484 done(ep0, req, 0); 1485 /* that may have STALLed ep0... */ 1486 omap_writew(UDC_EP_SEL | UDC_EP_DIR, 1487 UDC_EP_NUM); 1488 omap_writew(UDC_CLR_EP, UDC_CTRL); 1489 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 1490 omap_writew(UDC_EP_DIR, UDC_EP_NUM); 1491 udc->ep0_pending = 0; 1492 } 1493 } else { 1494 /* ack status stage of IN transfer */ 1495 omap_writew(0, UDC_EP_NUM); 1496 if (req) 1497 done(ep0, req, 0); 1498 } 1499 } else if (stat & UDC_STALL) { 1500 omap_writew(UDC_CLR_HALT, UDC_CTRL); 1501 omap_writew(0, UDC_EP_NUM); 1502 } else { 1503 omap_writew(0, UDC_EP_NUM); 1504 } 1505 } 1506 1507 /* SETUP starts all control transfers */ 1508 if (irq_src & UDC_SETUP) { 1509 union u { 1510 u16 word[4]; 1511 struct usb_ctrlrequest r; 1512 } u; 1513 int status = -EINVAL; 1514 struct omap_ep *ep; 1515 1516 /* read the (latest) SETUP message */ 1517 do { 1518 omap_writew(UDC_SETUP_SEL, UDC_EP_NUM); 1519 /* two bytes at a time */ 1520 u.word[0] = omap_readw(UDC_DATA); 1521 u.word[1] = omap_readw(UDC_DATA); 1522 u.word[2] = omap_readw(UDC_DATA); 1523 u.word[3] = omap_readw(UDC_DATA); 1524 omap_writew(0, UDC_EP_NUM); 1525 } while (omap_readw(UDC_IRQ_SRC) & UDC_SETUP); 1526 1527 #define w_value le16_to_cpu(u.r.wValue) 1528 #define w_index le16_to_cpu(u.r.wIndex) 1529 #define w_length le16_to_cpu(u.r.wLength) 1530 1531 /* Delegate almost all control requests to the gadget driver, 1532 * except for a handful of ch9 status/feature requests that 1533 * hardware doesn't autodecode _and_ the gadget API hides. 1534 */ 1535 udc->ep0_in = (u.r.bRequestType & USB_DIR_IN) != 0; 1536 udc->ep0_set_config = 0; 1537 udc->ep0_pending = 1; 1538 ep0->stopped = 0; 1539 ep0->ackwait = 0; 1540 switch (u.r.bRequest) { 1541 case USB_REQ_SET_CONFIGURATION: 1542 /* udc needs to know when ep != 0 is valid */ 1543 if (u.r.bRequestType != USB_RECIP_DEVICE) 1544 goto delegate; 1545 if (w_length != 0) 1546 goto do_stall; 1547 udc->ep0_set_config = 1; 1548 udc->ep0_reset_config = (w_value == 0); 1549 VDBG("set config %d\n", w_value); 1550 1551 /* update udc NOW since gadget driver may start 1552 * queueing requests immediately; clear config 1553 * later if it fails the request. 1554 */ 1555 if (udc->ep0_reset_config) 1556 omap_writew(UDC_CLR_CFG, UDC_SYSCON2); 1557 else 1558 omap_writew(UDC_DEV_CFG, UDC_SYSCON2); 1559 update_otg(udc); 1560 goto delegate; 1561 case USB_REQ_CLEAR_FEATURE: 1562 /* clear endpoint halt */ 1563 if (u.r.bRequestType != USB_RECIP_ENDPOINT) 1564 goto delegate; 1565 if (w_value != USB_ENDPOINT_HALT 1566 || w_length != 0) 1567 goto do_stall; 1568 ep = &udc->ep[w_index & 0xf]; 1569 if (ep != ep0) { 1570 if (w_index & USB_DIR_IN) 1571 ep += 16; 1572 if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC 1573 || !ep->ep.desc) 1574 goto do_stall; 1575 use_ep(ep, 0); 1576 omap_writew(udc->clr_halt, UDC_CTRL); 1577 ep->ackwait = 0; 1578 if (!(ep->bEndpointAddress & USB_DIR_IN)) { 1579 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 1580 ep->ackwait = 1 + ep->double_buf; 1581 } 1582 /* NOTE: assumes the host behaves sanely, 1583 * only clearing real halts. Else we may 1584 * need to kill pending transfers and then 1585 * restart the queue... very messy for DMA! 1586 */ 1587 } 1588 VDBG("%s halt cleared by host\n", ep->name); 1589 goto ep0out_status_stage; 1590 case USB_REQ_SET_FEATURE: 1591 /* set endpoint halt */ 1592 if (u.r.bRequestType != USB_RECIP_ENDPOINT) 1593 goto delegate; 1594 if (w_value != USB_ENDPOINT_HALT 1595 || w_length != 0) 1596 goto do_stall; 1597 ep = &udc->ep[w_index & 0xf]; 1598 if (w_index & USB_DIR_IN) 1599 ep += 16; 1600 if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC 1601 || ep == ep0 || !ep->ep.desc) 1602 goto do_stall; 1603 if (use_dma && ep->has_dma) { 1604 /* this has rude side-effects (aborts) and 1605 * can't really work if DMA-IN is active 1606 */ 1607 DBG("%s host set_halt, NYET\n", ep->name); 1608 goto do_stall; 1609 } 1610 use_ep(ep, 0); 1611 /* can't halt if fifo isn't empty... */ 1612 omap_writew(UDC_CLR_EP, UDC_CTRL); 1613 omap_writew(UDC_SET_HALT, UDC_CTRL); 1614 VDBG("%s halted by host\n", ep->name); 1615 ep0out_status_stage: 1616 status = 0; 1617 omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM); 1618 omap_writew(UDC_CLR_EP, UDC_CTRL); 1619 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 1620 omap_writew(UDC_EP_DIR, UDC_EP_NUM); 1621 udc->ep0_pending = 0; 1622 break; 1623 case USB_REQ_GET_STATUS: 1624 /* USB_ENDPOINT_HALT status? */ 1625 if (u.r.bRequestType != (USB_DIR_IN|USB_RECIP_ENDPOINT)) 1626 goto intf_status; 1627 1628 /* ep0 never stalls */ 1629 if (!(w_index & 0xf)) 1630 goto zero_status; 1631 1632 /* only active endpoints count */ 1633 ep = &udc->ep[w_index & 0xf]; 1634 if (w_index & USB_DIR_IN) 1635 ep += 16; 1636 if (!ep->ep.desc) 1637 goto do_stall; 1638 1639 /* iso never stalls */ 1640 if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) 1641 goto zero_status; 1642 1643 /* FIXME don't assume non-halted endpoints!! */ 1644 ERR("%s status, can't report\n", ep->ep.name); 1645 goto do_stall; 1646 1647 intf_status: 1648 /* return interface status. if we were pedantic, 1649 * we'd detect non-existent interfaces, and stall. 1650 */ 1651 if (u.r.bRequestType 1652 != (USB_DIR_IN|USB_RECIP_INTERFACE)) 1653 goto delegate; 1654 1655 zero_status: 1656 /* return two zero bytes */ 1657 omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM); 1658 omap_writew(0, UDC_DATA); 1659 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 1660 omap_writew(UDC_EP_DIR, UDC_EP_NUM); 1661 status = 0; 1662 VDBG("GET_STATUS, interface %d\n", w_index); 1663 /* next, status stage */ 1664 break; 1665 default: 1666 delegate: 1667 /* activate the ep0out fifo right away */ 1668 if (!udc->ep0_in && w_length) { 1669 omap_writew(0, UDC_EP_NUM); 1670 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 1671 } 1672 1673 /* gadget drivers see class/vendor specific requests, 1674 * {SET,GET}_{INTERFACE,DESCRIPTOR,CONFIGURATION}, 1675 * and more 1676 */ 1677 VDBG("SETUP %02x.%02x v%04x i%04x l%04x\n", 1678 u.r.bRequestType, u.r.bRequest, 1679 w_value, w_index, w_length); 1680 1681 #undef w_value 1682 #undef w_index 1683 #undef w_length 1684 1685 /* The gadget driver may return an error here, 1686 * causing an immediate protocol stall. 1687 * 1688 * Else it must issue a response, either queueing a 1689 * response buffer for the DATA stage, or halting ep0 1690 * (causing a protocol stall, not a real halt). A 1691 * zero length buffer means no DATA stage. 1692 * 1693 * It's fine to issue that response after the setup() 1694 * call returns, and this IRQ was handled. 1695 */ 1696 udc->ep0_setup = 1; 1697 spin_unlock(&udc->lock); 1698 status = udc->driver->setup(&udc->gadget, &u.r); 1699 spin_lock(&udc->lock); 1700 udc->ep0_setup = 0; 1701 } 1702 1703 if (status < 0) { 1704 do_stall: 1705 VDBG("req %02x.%02x protocol STALL; stat %d\n", 1706 u.r.bRequestType, u.r.bRequest, status); 1707 if (udc->ep0_set_config) { 1708 if (udc->ep0_reset_config) 1709 WARNING("error resetting config?\n"); 1710 else 1711 omap_writew(UDC_CLR_CFG, UDC_SYSCON2); 1712 } 1713 omap_writew(UDC_STALL_CMD, UDC_SYSCON2); 1714 udc->ep0_pending = 0; 1715 } 1716 } 1717 } 1718 1719 /*-------------------------------------------------------------------------*/ 1720 1721 #define OTG_FLAGS (UDC_B_HNP_ENABLE|UDC_A_HNP_SUPPORT|UDC_A_ALT_HNP_SUPPORT) 1722 1723 static void devstate_irq(struct omap_udc *udc, u16 irq_src) 1724 { 1725 u16 devstat, change; 1726 1727 devstat = omap_readw(UDC_DEVSTAT); 1728 change = devstat ^ udc->devstat; 1729 udc->devstat = devstat; 1730 1731 if (change & (UDC_USB_RESET|UDC_ATT)) { 1732 udc_quiesce(udc); 1733 1734 if (change & UDC_ATT) { 1735 /* driver for any external transceiver will 1736 * have called omap_vbus_session() already 1737 */ 1738 if (devstat & UDC_ATT) { 1739 udc->gadget.speed = USB_SPEED_FULL; 1740 VDBG("connect\n"); 1741 if (IS_ERR_OR_NULL(udc->transceiver)) 1742 pullup_enable(udc); 1743 /* if (driver->connect) call it */ 1744 } else if (udc->gadget.speed != USB_SPEED_UNKNOWN) { 1745 udc->gadget.speed = USB_SPEED_UNKNOWN; 1746 if (IS_ERR_OR_NULL(udc->transceiver)) 1747 pullup_disable(udc); 1748 DBG("disconnect, gadget %s\n", 1749 udc->driver->driver.name); 1750 if (udc->driver->disconnect) { 1751 spin_unlock(&udc->lock); 1752 udc->driver->disconnect(&udc->gadget); 1753 spin_lock(&udc->lock); 1754 } 1755 } 1756 change &= ~UDC_ATT; 1757 } 1758 1759 if (change & UDC_USB_RESET) { 1760 if (devstat & UDC_USB_RESET) { 1761 VDBG("RESET=1\n"); 1762 } else { 1763 udc->gadget.speed = USB_SPEED_FULL; 1764 INFO("USB reset done, gadget %s\n", 1765 udc->driver->driver.name); 1766 /* ep0 traffic is legal from now on */ 1767 omap_writew(UDC_DS_CHG_IE | UDC_EP0_IE, 1768 UDC_IRQ_EN); 1769 } 1770 change &= ~UDC_USB_RESET; 1771 } 1772 } 1773 if (change & UDC_SUS) { 1774 if (udc->gadget.speed != USB_SPEED_UNKNOWN) { 1775 /* FIXME tell isp1301 to suspend/resume (?) */ 1776 if (devstat & UDC_SUS) { 1777 VDBG("suspend\n"); 1778 update_otg(udc); 1779 /* HNP could be under way already */ 1780 if (udc->gadget.speed == USB_SPEED_FULL 1781 && udc->driver->suspend) { 1782 spin_unlock(&udc->lock); 1783 udc->driver->suspend(&udc->gadget); 1784 spin_lock(&udc->lock); 1785 } 1786 if (!IS_ERR_OR_NULL(udc->transceiver)) 1787 usb_phy_set_suspend( 1788 udc->transceiver, 1); 1789 } else { 1790 VDBG("resume\n"); 1791 if (!IS_ERR_OR_NULL(udc->transceiver)) 1792 usb_phy_set_suspend( 1793 udc->transceiver, 0); 1794 if (udc->gadget.speed == USB_SPEED_FULL 1795 && udc->driver->resume) { 1796 spin_unlock(&udc->lock); 1797 udc->driver->resume(&udc->gadget); 1798 spin_lock(&udc->lock); 1799 } 1800 } 1801 } 1802 change &= ~UDC_SUS; 1803 } 1804 if (!cpu_is_omap15xx() && (change & OTG_FLAGS)) { 1805 update_otg(udc); 1806 change &= ~OTG_FLAGS; 1807 } 1808 1809 change &= ~(UDC_CFG|UDC_DEF|UDC_ADD); 1810 if (change) 1811 VDBG("devstat %03x, ignore change %03x\n", 1812 devstat, change); 1813 1814 omap_writew(UDC_DS_CHG, UDC_IRQ_SRC); 1815 } 1816 1817 static irqreturn_t omap_udc_irq(int irq, void *_udc) 1818 { 1819 struct omap_udc *udc = _udc; 1820 u16 irq_src; 1821 irqreturn_t status = IRQ_NONE; 1822 unsigned long flags; 1823 1824 spin_lock_irqsave(&udc->lock, flags); 1825 irq_src = omap_readw(UDC_IRQ_SRC); 1826 1827 /* Device state change (usb ch9 stuff) */ 1828 if (irq_src & UDC_DS_CHG) { 1829 devstate_irq(_udc, irq_src); 1830 status = IRQ_HANDLED; 1831 irq_src &= ~UDC_DS_CHG; 1832 } 1833 1834 /* EP0 control transfers */ 1835 if (irq_src & (UDC_EP0_RX|UDC_SETUP|UDC_EP0_TX)) { 1836 ep0_irq(_udc, irq_src); 1837 status = IRQ_HANDLED; 1838 irq_src &= ~(UDC_EP0_RX|UDC_SETUP|UDC_EP0_TX); 1839 } 1840 1841 /* DMA transfer completion */ 1842 if (use_dma && (irq_src & (UDC_TXN_DONE|UDC_RXN_CNT|UDC_RXN_EOT))) { 1843 dma_irq(_udc, irq_src); 1844 status = IRQ_HANDLED; 1845 irq_src &= ~(UDC_TXN_DONE|UDC_RXN_CNT|UDC_RXN_EOT); 1846 } 1847 1848 irq_src &= ~(UDC_IRQ_SOF | UDC_EPN_TX|UDC_EPN_RX); 1849 if (irq_src) 1850 DBG("udc_irq, unhandled %03x\n", irq_src); 1851 spin_unlock_irqrestore(&udc->lock, flags); 1852 1853 return status; 1854 } 1855 1856 /* workaround for seemingly-lost IRQs for RX ACKs... */ 1857 #define PIO_OUT_TIMEOUT (jiffies + HZ/3) 1858 #define HALF_FULL(f) (!((f)&(UDC_NON_ISO_FIFO_FULL|UDC_NON_ISO_FIFO_EMPTY))) 1859 1860 static void pio_out_timer(unsigned long _ep) 1861 { 1862 struct omap_ep *ep = (void *) _ep; 1863 unsigned long flags; 1864 u16 stat_flg; 1865 1866 spin_lock_irqsave(&ep->udc->lock, flags); 1867 if (!list_empty(&ep->queue) && ep->ackwait) { 1868 use_ep(ep, UDC_EP_SEL); 1869 stat_flg = omap_readw(UDC_STAT_FLG); 1870 1871 if ((stat_flg & UDC_ACK) && (!(stat_flg & UDC_FIFO_EN) 1872 || (ep->double_buf && HALF_FULL(stat_flg)))) { 1873 struct omap_req *req; 1874 1875 VDBG("%s: lose, %04x\n", ep->ep.name, stat_flg); 1876 req = container_of(ep->queue.next, 1877 struct omap_req, queue); 1878 (void) read_fifo(ep, req); 1879 omap_writew(ep->bEndpointAddress, UDC_EP_NUM); 1880 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 1881 ep->ackwait = 1 + ep->double_buf; 1882 } else 1883 deselect_ep(); 1884 } 1885 mod_timer(&ep->timer, PIO_OUT_TIMEOUT); 1886 spin_unlock_irqrestore(&ep->udc->lock, flags); 1887 } 1888 1889 static irqreturn_t omap_udc_pio_irq(int irq, void *_dev) 1890 { 1891 u16 epn_stat, irq_src; 1892 irqreturn_t status = IRQ_NONE; 1893 struct omap_ep *ep; 1894 int epnum; 1895 struct omap_udc *udc = _dev; 1896 struct omap_req *req; 1897 unsigned long flags; 1898 1899 spin_lock_irqsave(&udc->lock, flags); 1900 epn_stat = omap_readw(UDC_EPN_STAT); 1901 irq_src = omap_readw(UDC_IRQ_SRC); 1902 1903 /* handle OUT first, to avoid some wasteful NAKs */ 1904 if (irq_src & UDC_EPN_RX) { 1905 epnum = (epn_stat >> 8) & 0x0f; 1906 omap_writew(UDC_EPN_RX, UDC_IRQ_SRC); 1907 status = IRQ_HANDLED; 1908 ep = &udc->ep[epnum]; 1909 ep->irqs++; 1910 1911 omap_writew(epnum | UDC_EP_SEL, UDC_EP_NUM); 1912 ep->fnf = 0; 1913 if (omap_readw(UDC_STAT_FLG) & UDC_ACK) { 1914 ep->ackwait--; 1915 if (!list_empty(&ep->queue)) { 1916 int stat; 1917 req = container_of(ep->queue.next, 1918 struct omap_req, queue); 1919 stat = read_fifo(ep, req); 1920 if (!ep->double_buf) 1921 ep->fnf = 1; 1922 } 1923 } 1924 /* min 6 clock delay before clearing EP_SEL ... */ 1925 epn_stat = omap_readw(UDC_EPN_STAT); 1926 epn_stat = omap_readw(UDC_EPN_STAT); 1927 omap_writew(epnum, UDC_EP_NUM); 1928 1929 /* enabling fifo _after_ clearing ACK, contrary to docs, 1930 * reduces lossage; timer still needed though (sigh). 1931 */ 1932 if (ep->fnf) { 1933 omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); 1934 ep->ackwait = 1 + ep->double_buf; 1935 } 1936 mod_timer(&ep->timer, PIO_OUT_TIMEOUT); 1937 } 1938 1939 /* then IN transfers */ 1940 else if (irq_src & UDC_EPN_TX) { 1941 epnum = epn_stat & 0x0f; 1942 omap_writew(UDC_EPN_TX, UDC_IRQ_SRC); 1943 status = IRQ_HANDLED; 1944 ep = &udc->ep[16 + epnum]; 1945 ep->irqs++; 1946 1947 omap_writew(epnum | UDC_EP_DIR | UDC_EP_SEL, UDC_EP_NUM); 1948 if (omap_readw(UDC_STAT_FLG) & UDC_ACK) { 1949 ep->ackwait = 0; 1950 if (!list_empty(&ep->queue)) { 1951 req = container_of(ep->queue.next, 1952 struct omap_req, queue); 1953 (void) write_fifo(ep, req); 1954 } 1955 } 1956 /* min 6 clock delay before clearing EP_SEL ... */ 1957 epn_stat = omap_readw(UDC_EPN_STAT); 1958 epn_stat = omap_readw(UDC_EPN_STAT); 1959 omap_writew(epnum | UDC_EP_DIR, UDC_EP_NUM); 1960 /* then 6 clocks before it'd tx */ 1961 } 1962 1963 spin_unlock_irqrestore(&udc->lock, flags); 1964 return status; 1965 } 1966 1967 #ifdef USE_ISO 1968 static irqreturn_t omap_udc_iso_irq(int irq, void *_dev) 1969 { 1970 struct omap_udc *udc = _dev; 1971 struct omap_ep *ep; 1972 int pending = 0; 1973 unsigned long flags; 1974 1975 spin_lock_irqsave(&udc->lock, flags); 1976 1977 /* handle all non-DMA ISO transfers */ 1978 list_for_each_entry(ep, &udc->iso, iso) { 1979 u16 stat; 1980 struct omap_req *req; 1981 1982 if (ep->has_dma || list_empty(&ep->queue)) 1983 continue; 1984 req = list_entry(ep->queue.next, struct omap_req, queue); 1985 1986 use_ep(ep, UDC_EP_SEL); 1987 stat = omap_readw(UDC_STAT_FLG); 1988 1989 /* NOTE: like the other controller drivers, this isn't 1990 * currently reporting lost or damaged frames. 1991 */ 1992 if (ep->bEndpointAddress & USB_DIR_IN) { 1993 if (stat & UDC_MISS_IN) 1994 /* done(ep, req, -EPROTO) */; 1995 else 1996 write_fifo(ep, req); 1997 } else { 1998 int status = 0; 1999 2000 if (stat & UDC_NO_RXPACKET) 2001 status = -EREMOTEIO; 2002 else if (stat & UDC_ISO_ERR) 2003 status = -EILSEQ; 2004 else if (stat & UDC_DATA_FLUSH) 2005 status = -ENOSR; 2006 2007 if (status) 2008 /* done(ep, req, status) */; 2009 else 2010 read_fifo(ep, req); 2011 } 2012 deselect_ep(); 2013 /* 6 wait states before next EP */ 2014 2015 ep->irqs++; 2016 if (!list_empty(&ep->queue)) 2017 pending = 1; 2018 } 2019 if (!pending) { 2020 u16 w; 2021 2022 w = omap_readw(UDC_IRQ_EN); 2023 w &= ~UDC_SOF_IE; 2024 omap_writew(w, UDC_IRQ_EN); 2025 } 2026 omap_writew(UDC_IRQ_SOF, UDC_IRQ_SRC); 2027 2028 spin_unlock_irqrestore(&udc->lock, flags); 2029 return IRQ_HANDLED; 2030 } 2031 #endif 2032 2033 /*-------------------------------------------------------------------------*/ 2034 2035 static inline int machine_without_vbus_sense(void) 2036 { 2037 return machine_is_omap_innovator() 2038 || machine_is_omap_osk() 2039 || machine_is_sx1() 2040 /* No known omap7xx boards with vbus sense */ 2041 || cpu_is_omap7xx(); 2042 } 2043 2044 static int omap_udc_start(struct usb_gadget *g, 2045 struct usb_gadget_driver *driver) 2046 { 2047 int status = -ENODEV; 2048 struct omap_ep *ep; 2049 unsigned long flags; 2050 2051 2052 spin_lock_irqsave(&udc->lock, flags); 2053 /* reset state */ 2054 list_for_each_entry(ep, &udc->gadget.ep_list, ep.ep_list) { 2055 ep->irqs = 0; 2056 if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) 2057 continue; 2058 use_ep(ep, 0); 2059 omap_writew(UDC_SET_HALT, UDC_CTRL); 2060 } 2061 udc->ep0_pending = 0; 2062 udc->ep[0].irqs = 0; 2063 udc->softconnect = 1; 2064 2065 /* hook up the driver */ 2066 driver->driver.bus = NULL; 2067 udc->driver = driver; 2068 spin_unlock_irqrestore(&udc->lock, flags); 2069 2070 if (udc->dc_clk != NULL) 2071 omap_udc_enable_clock(1); 2072 2073 omap_writew(UDC_IRQ_SRC_MASK, UDC_IRQ_SRC); 2074 2075 /* connect to bus through transceiver */ 2076 if (!IS_ERR_OR_NULL(udc->transceiver)) { 2077 status = otg_set_peripheral(udc->transceiver->otg, 2078 &udc->gadget); 2079 if (status < 0) { 2080 ERR("can't bind to transceiver\n"); 2081 udc->driver = NULL; 2082 goto done; 2083 } 2084 } else { 2085 if (can_pullup(udc)) 2086 pullup_enable(udc); 2087 else 2088 pullup_disable(udc); 2089 } 2090 2091 /* boards that don't have VBUS sensing can't autogate 48MHz; 2092 * can't enter deep sleep while a gadget driver is active. 2093 */ 2094 if (machine_without_vbus_sense()) 2095 omap_vbus_session(&udc->gadget, 1); 2096 2097 done: 2098 if (udc->dc_clk != NULL) 2099 omap_udc_enable_clock(0); 2100 2101 return status; 2102 } 2103 2104 static int omap_udc_stop(struct usb_gadget *g) 2105 { 2106 unsigned long flags; 2107 int status = -ENODEV; 2108 2109 if (udc->dc_clk != NULL) 2110 omap_udc_enable_clock(1); 2111 2112 if (machine_without_vbus_sense()) 2113 omap_vbus_session(&udc->gadget, 0); 2114 2115 if (!IS_ERR_OR_NULL(udc->transceiver)) 2116 (void) otg_set_peripheral(udc->transceiver->otg, NULL); 2117 else 2118 pullup_disable(udc); 2119 2120 spin_lock_irqsave(&udc->lock, flags); 2121 udc_quiesce(udc); 2122 spin_unlock_irqrestore(&udc->lock, flags); 2123 2124 udc->driver = NULL; 2125 2126 if (udc->dc_clk != NULL) 2127 omap_udc_enable_clock(0); 2128 2129 return status; 2130 } 2131 2132 /*-------------------------------------------------------------------------*/ 2133 2134 #ifdef CONFIG_USB_GADGET_DEBUG_FILES 2135 2136 #include <linux/seq_file.h> 2137 2138 static const char proc_filename[] = "driver/udc"; 2139 2140 #define FOURBITS "%s%s%s%s" 2141 #define EIGHTBITS "%s%s%s%s%s%s%s%s" 2142 2143 static void proc_ep_show(struct seq_file *s, struct omap_ep *ep) 2144 { 2145 u16 stat_flg; 2146 struct omap_req *req; 2147 char buf[20]; 2148 2149 use_ep(ep, 0); 2150 2151 if (use_dma && ep->has_dma) 2152 snprintf(buf, sizeof buf, "(%cxdma%d lch%d) ", 2153 (ep->bEndpointAddress & USB_DIR_IN) ? 't' : 'r', 2154 ep->dma_channel - 1, ep->lch); 2155 else 2156 buf[0] = 0; 2157 2158 stat_flg = omap_readw(UDC_STAT_FLG); 2159 seq_printf(s, 2160 "\n%s %s%s%sirqs %ld stat %04x " EIGHTBITS FOURBITS "%s\n", 2161 ep->name, buf, 2162 ep->double_buf ? "dbuf " : "", 2163 ({ char *s; 2164 switch (ep->ackwait) { 2165 case 0: 2166 s = ""; 2167 break; 2168 case 1: 2169 s = "(ackw) "; 2170 break; 2171 case 2: 2172 s = "(ackw2) "; 2173 break; 2174 default: 2175 s = "(?) "; 2176 break; 2177 } s; }), 2178 ep->irqs, stat_flg, 2179 (stat_flg & UDC_NO_RXPACKET) ? "no_rxpacket " : "", 2180 (stat_flg & UDC_MISS_IN) ? "miss_in " : "", 2181 (stat_flg & UDC_DATA_FLUSH) ? "data_flush " : "", 2182 (stat_flg & UDC_ISO_ERR) ? "iso_err " : "", 2183 (stat_flg & UDC_ISO_FIFO_EMPTY) ? "iso_fifo_empty " : "", 2184 (stat_flg & UDC_ISO_FIFO_FULL) ? "iso_fifo_full " : "", 2185 (stat_flg & UDC_EP_HALTED) ? "HALT " : "", 2186 (stat_flg & UDC_STALL) ? "STALL " : "", 2187 (stat_flg & UDC_NAK) ? "NAK " : "", 2188 (stat_flg & UDC_ACK) ? "ACK " : "", 2189 (stat_flg & UDC_FIFO_EN) ? "fifo_en " : "", 2190 (stat_flg & UDC_NON_ISO_FIFO_EMPTY) ? "fifo_empty " : "", 2191 (stat_flg & UDC_NON_ISO_FIFO_FULL) ? "fifo_full " : ""); 2192 2193 if (list_empty(&ep->queue)) 2194 seq_printf(s, "\t(queue empty)\n"); 2195 else 2196 list_for_each_entry(req, &ep->queue, queue) { 2197 unsigned length = req->req.actual; 2198 2199 if (use_dma && buf[0]) { 2200 length += ((ep->bEndpointAddress & USB_DIR_IN) 2201 ? dma_src_len : dma_dest_len) 2202 (ep, req->req.dma + length); 2203 buf[0] = 0; 2204 } 2205 seq_printf(s, "\treq %p len %d/%d buf %p\n", 2206 &req->req, length, 2207 req->req.length, req->req.buf); 2208 } 2209 } 2210 2211 static char *trx_mode(unsigned m, int enabled) 2212 { 2213 switch (m) { 2214 case 0: 2215 return enabled ? "*6wire" : "unused"; 2216 case 1: 2217 return "4wire"; 2218 case 2: 2219 return "3wire"; 2220 case 3: 2221 return "6wire"; 2222 default: 2223 return "unknown"; 2224 } 2225 } 2226 2227 static int proc_otg_show(struct seq_file *s) 2228 { 2229 u32 tmp; 2230 u32 trans = 0; 2231 char *ctrl_name = "(UNKNOWN)"; 2232 2233 tmp = omap_readl(OTG_REV); 2234 ctrl_name = "tranceiver_ctrl"; 2235 trans = omap_readw(USB_TRANSCEIVER_CTRL); 2236 seq_printf(s, "\nOTG rev %d.%d, %s %05x\n", 2237 tmp >> 4, tmp & 0xf, ctrl_name, trans); 2238 tmp = omap_readw(OTG_SYSCON_1); 2239 seq_printf(s, "otg_syscon1 %08x usb2 %s, usb1 %s, usb0 %s," 2240 FOURBITS "\n", tmp, 2241 trx_mode(USB2_TRX_MODE(tmp), trans & CONF_USB2_UNI_R), 2242 trx_mode(USB1_TRX_MODE(tmp), trans & CONF_USB1_UNI_R), 2243 (USB0_TRX_MODE(tmp) == 0 && !cpu_is_omap1710()) 2244 ? "internal" 2245 : trx_mode(USB0_TRX_MODE(tmp), 1), 2246 (tmp & OTG_IDLE_EN) ? " !otg" : "", 2247 (tmp & HST_IDLE_EN) ? " !host" : "", 2248 (tmp & DEV_IDLE_EN) ? " !dev" : "", 2249 (tmp & OTG_RESET_DONE) ? " reset_done" : " reset_active"); 2250 tmp = omap_readl(OTG_SYSCON_2); 2251 seq_printf(s, "otg_syscon2 %08x%s" EIGHTBITS 2252 " b_ase_brst=%d hmc=%d\n", tmp, 2253 (tmp & OTG_EN) ? " otg_en" : "", 2254 (tmp & USBX_SYNCHRO) ? " synchro" : "", 2255 /* much more SRP stuff */ 2256 (tmp & SRP_DATA) ? " srp_data" : "", 2257 (tmp & SRP_VBUS) ? " srp_vbus" : "", 2258 (tmp & OTG_PADEN) ? " otg_paden" : "", 2259 (tmp & HMC_PADEN) ? " hmc_paden" : "", 2260 (tmp & UHOST_EN) ? " uhost_en" : "", 2261 (tmp & HMC_TLLSPEED) ? " tllspeed" : "", 2262 (tmp & HMC_TLLATTACH) ? " tllattach" : "", 2263 B_ASE_BRST(tmp), 2264 OTG_HMC(tmp)); 2265 tmp = omap_readl(OTG_CTRL); 2266 seq_printf(s, "otg_ctrl %06x" EIGHTBITS EIGHTBITS "%s\n", tmp, 2267 (tmp & OTG_ASESSVLD) ? " asess" : "", 2268 (tmp & OTG_BSESSEND) ? " bsess_end" : "", 2269 (tmp & OTG_BSESSVLD) ? " bsess" : "", 2270 (tmp & OTG_VBUSVLD) ? " vbus" : "", 2271 (tmp & OTG_ID) ? " id" : "", 2272 (tmp & OTG_DRIVER_SEL) ? " DEVICE" : " HOST", 2273 (tmp & OTG_A_SETB_HNPEN) ? " a_setb_hnpen" : "", 2274 (tmp & OTG_A_BUSREQ) ? " a_bus" : "", 2275 (tmp & OTG_B_HNPEN) ? " b_hnpen" : "", 2276 (tmp & OTG_B_BUSREQ) ? " b_bus" : "", 2277 (tmp & OTG_BUSDROP) ? " busdrop" : "", 2278 (tmp & OTG_PULLDOWN) ? " down" : "", 2279 (tmp & OTG_PULLUP) ? " up" : "", 2280 (tmp & OTG_DRV_VBUS) ? " drv" : "", 2281 (tmp & OTG_PD_VBUS) ? " pd_vb" : "", 2282 (tmp & OTG_PU_VBUS) ? " pu_vb" : "", 2283 (tmp & OTG_PU_ID) ? " pu_id" : "" 2284 ); 2285 tmp = omap_readw(OTG_IRQ_EN); 2286 seq_printf(s, "otg_irq_en %04x" "\n", tmp); 2287 tmp = omap_readw(OTG_IRQ_SRC); 2288 seq_printf(s, "otg_irq_src %04x" "\n", tmp); 2289 tmp = omap_readw(OTG_OUTCTRL); 2290 seq_printf(s, "otg_outctrl %04x" "\n", tmp); 2291 tmp = omap_readw(OTG_TEST); 2292 seq_printf(s, "otg_test %04x" "\n", tmp); 2293 return 0; 2294 } 2295 2296 static int proc_udc_show(struct seq_file *s, void *_) 2297 { 2298 u32 tmp; 2299 struct omap_ep *ep; 2300 unsigned long flags; 2301 2302 spin_lock_irqsave(&udc->lock, flags); 2303 2304 seq_printf(s, "%s, version: " DRIVER_VERSION 2305 #ifdef USE_ISO 2306 " (iso)" 2307 #endif 2308 "%s\n", 2309 driver_desc, 2310 use_dma ? " (dma)" : ""); 2311 2312 tmp = omap_readw(UDC_REV) & 0xff; 2313 seq_printf(s, 2314 "UDC rev %d.%d, fifo mode %d, gadget %s\n" 2315 "hmc %d, transceiver %s\n", 2316 tmp >> 4, tmp & 0xf, 2317 fifo_mode, 2318 udc->driver ? udc->driver->driver.name : "(none)", 2319 HMC, 2320 udc->transceiver 2321 ? udc->transceiver->label 2322 : (cpu_is_omap1710() 2323 ? "external" : "(none)")); 2324 seq_printf(s, "ULPD control %04x req %04x status %04x\n", 2325 omap_readw(ULPD_CLOCK_CTRL), 2326 omap_readw(ULPD_SOFT_REQ), 2327 omap_readw(ULPD_STATUS_REQ)); 2328 2329 /* OTG controller registers */ 2330 if (!cpu_is_omap15xx()) 2331 proc_otg_show(s); 2332 2333 tmp = omap_readw(UDC_SYSCON1); 2334 seq_printf(s, "\nsyscon1 %04x" EIGHTBITS "\n", tmp, 2335 (tmp & UDC_CFG_LOCK) ? " cfg_lock" : "", 2336 (tmp & UDC_DATA_ENDIAN) ? " data_endian" : "", 2337 (tmp & UDC_DMA_ENDIAN) ? " dma_endian" : "", 2338 (tmp & UDC_NAK_EN) ? " nak" : "", 2339 (tmp & UDC_AUTODECODE_DIS) ? " autodecode_dis" : "", 2340 (tmp & UDC_SELF_PWR) ? " self_pwr" : "", 2341 (tmp & UDC_SOFF_DIS) ? " soff_dis" : "", 2342 (tmp & UDC_PULLUP_EN) ? " PULLUP" : ""); 2343 /* syscon2 is write-only */ 2344 2345 /* UDC controller registers */ 2346 if (!(tmp & UDC_PULLUP_EN)) { 2347 seq_printf(s, "(suspended)\n"); 2348 spin_unlock_irqrestore(&udc->lock, flags); 2349 return 0; 2350 } 2351 2352 tmp = omap_readw(UDC_DEVSTAT); 2353 seq_printf(s, "devstat %04x" EIGHTBITS "%s%s\n", tmp, 2354 (tmp & UDC_B_HNP_ENABLE) ? " b_hnp" : "", 2355 (tmp & UDC_A_HNP_SUPPORT) ? " a_hnp" : "", 2356 (tmp & UDC_A_ALT_HNP_SUPPORT) ? " a_alt_hnp" : "", 2357 (tmp & UDC_R_WK_OK) ? " r_wk_ok" : "", 2358 (tmp & UDC_USB_RESET) ? " usb_reset" : "", 2359 (tmp & UDC_SUS) ? " SUS" : "", 2360 (tmp & UDC_CFG) ? " CFG" : "", 2361 (tmp & UDC_ADD) ? " ADD" : "", 2362 (tmp & UDC_DEF) ? " DEF" : "", 2363 (tmp & UDC_ATT) ? " ATT" : ""); 2364 seq_printf(s, "sof %04x\n", omap_readw(UDC_SOF)); 2365 tmp = omap_readw(UDC_IRQ_EN); 2366 seq_printf(s, "irq_en %04x" FOURBITS "%s\n", tmp, 2367 (tmp & UDC_SOF_IE) ? " sof" : "", 2368 (tmp & UDC_EPN_RX_IE) ? " epn_rx" : "", 2369 (tmp & UDC_EPN_TX_IE) ? " epn_tx" : "", 2370 (tmp & UDC_DS_CHG_IE) ? " ds_chg" : "", 2371 (tmp & UDC_EP0_IE) ? " ep0" : ""); 2372 tmp = omap_readw(UDC_IRQ_SRC); 2373 seq_printf(s, "irq_src %04x" EIGHTBITS "%s%s\n", tmp, 2374 (tmp & UDC_TXN_DONE) ? " txn_done" : "", 2375 (tmp & UDC_RXN_CNT) ? " rxn_cnt" : "", 2376 (tmp & UDC_RXN_EOT) ? " rxn_eot" : "", 2377 (tmp & UDC_IRQ_SOF) ? " sof" : "", 2378 (tmp & UDC_EPN_RX) ? " epn_rx" : "", 2379 (tmp & UDC_EPN_TX) ? " epn_tx" : "", 2380 (tmp & UDC_DS_CHG) ? " ds_chg" : "", 2381 (tmp & UDC_SETUP) ? " setup" : "", 2382 (tmp & UDC_EP0_RX) ? " ep0out" : "", 2383 (tmp & UDC_EP0_TX) ? " ep0in" : ""); 2384 if (use_dma) { 2385 unsigned i; 2386 2387 tmp = omap_readw(UDC_DMA_IRQ_EN); 2388 seq_printf(s, "dma_irq_en %04x%s" EIGHTBITS "\n", tmp, 2389 (tmp & UDC_TX_DONE_IE(3)) ? " tx2_done" : "", 2390 (tmp & UDC_RX_CNT_IE(3)) ? " rx2_cnt" : "", 2391 (tmp & UDC_RX_EOT_IE(3)) ? " rx2_eot" : "", 2392 2393 (tmp & UDC_TX_DONE_IE(2)) ? " tx1_done" : "", 2394 (tmp & UDC_RX_CNT_IE(2)) ? " rx1_cnt" : "", 2395 (tmp & UDC_RX_EOT_IE(2)) ? " rx1_eot" : "", 2396 2397 (tmp & UDC_TX_DONE_IE(1)) ? " tx0_done" : "", 2398 (tmp & UDC_RX_CNT_IE(1)) ? " rx0_cnt" : "", 2399 (tmp & UDC_RX_EOT_IE(1)) ? " rx0_eot" : ""); 2400 2401 tmp = omap_readw(UDC_RXDMA_CFG); 2402 seq_printf(s, "rxdma_cfg %04x\n", tmp); 2403 if (tmp) { 2404 for (i = 0; i < 3; i++) { 2405 if ((tmp & (0x0f << (i * 4))) == 0) 2406 continue; 2407 seq_printf(s, "rxdma[%d] %04x\n", i, 2408 omap_readw(UDC_RXDMA(i + 1))); 2409 } 2410 } 2411 tmp = omap_readw(UDC_TXDMA_CFG); 2412 seq_printf(s, "txdma_cfg %04x\n", tmp); 2413 if (tmp) { 2414 for (i = 0; i < 3; i++) { 2415 if (!(tmp & (0x0f << (i * 4)))) 2416 continue; 2417 seq_printf(s, "txdma[%d] %04x\n", i, 2418 omap_readw(UDC_TXDMA(i + 1))); 2419 } 2420 } 2421 } 2422 2423 tmp = omap_readw(UDC_DEVSTAT); 2424 if (tmp & UDC_ATT) { 2425 proc_ep_show(s, &udc->ep[0]); 2426 if (tmp & UDC_ADD) { 2427 list_for_each_entry(ep, &udc->gadget.ep_list, 2428 ep.ep_list) { 2429 if (ep->ep.desc) 2430 proc_ep_show(s, ep); 2431 } 2432 } 2433 } 2434 spin_unlock_irqrestore(&udc->lock, flags); 2435 return 0; 2436 } 2437 2438 static int proc_udc_open(struct inode *inode, struct file *file) 2439 { 2440 return single_open(file, proc_udc_show, NULL); 2441 } 2442 2443 static const struct file_operations proc_ops = { 2444 .owner = THIS_MODULE, 2445 .open = proc_udc_open, 2446 .read = seq_read, 2447 .llseek = seq_lseek, 2448 .release = single_release, 2449 }; 2450 2451 static void create_proc_file(void) 2452 { 2453 proc_create(proc_filename, 0, NULL, &proc_ops); 2454 } 2455 2456 static void remove_proc_file(void) 2457 { 2458 remove_proc_entry(proc_filename, NULL); 2459 } 2460 2461 #else 2462 2463 static inline void create_proc_file(void) {} 2464 static inline void remove_proc_file(void) {} 2465 2466 #endif 2467 2468 /*-------------------------------------------------------------------------*/ 2469 2470 /* Before this controller can enumerate, we need to pick an endpoint 2471 * configuration, or "fifo_mode" That involves allocating 2KB of packet 2472 * buffer space among the endpoints we'll be operating. 2473 * 2474 * NOTE: as of OMAP 1710 ES2.0, writing a new endpoint config when 2475 * UDC_SYSCON_1.CFG_LOCK is set can now work. We won't use that 2476 * capability yet though. 2477 */ 2478 static unsigned 2479 omap_ep_setup(char *name, u8 addr, u8 type, 2480 unsigned buf, unsigned maxp, int dbuf) 2481 { 2482 struct omap_ep *ep; 2483 u16 epn_rxtx = 0; 2484 2485 /* OUT endpoints first, then IN */ 2486 ep = &udc->ep[addr & 0xf]; 2487 if (addr & USB_DIR_IN) 2488 ep += 16; 2489 2490 /* in case of ep init table bugs */ 2491 BUG_ON(ep->name[0]); 2492 2493 /* chip setup ... bit values are same for IN, OUT */ 2494 if (type == USB_ENDPOINT_XFER_ISOC) { 2495 switch (maxp) { 2496 case 8: 2497 epn_rxtx = 0 << 12; 2498 break; 2499 case 16: 2500 epn_rxtx = 1 << 12; 2501 break; 2502 case 32: 2503 epn_rxtx = 2 << 12; 2504 break; 2505 case 64: 2506 epn_rxtx = 3 << 12; 2507 break; 2508 case 128: 2509 epn_rxtx = 4 << 12; 2510 break; 2511 case 256: 2512 epn_rxtx = 5 << 12; 2513 break; 2514 case 512: 2515 epn_rxtx = 6 << 12; 2516 break; 2517 default: 2518 BUG(); 2519 } 2520 epn_rxtx |= UDC_EPN_RX_ISO; 2521 dbuf = 1; 2522 } else { 2523 /* double-buffering "not supported" on 15xx, 2524 * and ignored for PIO-IN on newer chips 2525 * (for more reliable behavior) 2526 */ 2527 if (!use_dma || cpu_is_omap15xx()) 2528 dbuf = 0; 2529 2530 switch (maxp) { 2531 case 8: 2532 epn_rxtx = 0 << 12; 2533 break; 2534 case 16: 2535 epn_rxtx = 1 << 12; 2536 break; 2537 case 32: 2538 epn_rxtx = 2 << 12; 2539 break; 2540 case 64: 2541 epn_rxtx = 3 << 12; 2542 break; 2543 default: 2544 BUG(); 2545 } 2546 if (dbuf && addr) 2547 epn_rxtx |= UDC_EPN_RX_DB; 2548 init_timer(&ep->timer); 2549 ep->timer.function = pio_out_timer; 2550 ep->timer.data = (unsigned long) ep; 2551 } 2552 if (addr) 2553 epn_rxtx |= UDC_EPN_RX_VALID; 2554 BUG_ON(buf & 0x07); 2555 epn_rxtx |= buf >> 3; 2556 2557 DBG("%s addr %02x rxtx %04x maxp %d%s buf %d\n", 2558 name, addr, epn_rxtx, maxp, dbuf ? "x2" : "", buf); 2559 2560 if (addr & USB_DIR_IN) 2561 omap_writew(epn_rxtx, UDC_EP_TX(addr & 0xf)); 2562 else 2563 omap_writew(epn_rxtx, UDC_EP_RX(addr)); 2564 2565 /* next endpoint's buffer starts after this one's */ 2566 buf += maxp; 2567 if (dbuf) 2568 buf += maxp; 2569 BUG_ON(buf > 2048); 2570 2571 /* set up driver data structures */ 2572 BUG_ON(strlen(name) >= sizeof ep->name); 2573 strlcpy(ep->name, name, sizeof ep->name); 2574 INIT_LIST_HEAD(&ep->queue); 2575 INIT_LIST_HEAD(&ep->iso); 2576 ep->bEndpointAddress = addr; 2577 ep->bmAttributes = type; 2578 ep->double_buf = dbuf; 2579 ep->udc = udc; 2580 2581 ep->ep.name = ep->name; 2582 ep->ep.ops = &omap_ep_ops; 2583 ep->maxpacket = maxp; 2584 usb_ep_set_maxpacket_limit(&ep->ep, ep->maxpacket); 2585 list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list); 2586 2587 return buf; 2588 } 2589 2590 static void omap_udc_release(struct device *dev) 2591 { 2592 complete(udc->done); 2593 kfree(udc); 2594 udc = NULL; 2595 } 2596 2597 static int 2598 omap_udc_setup(struct platform_device *odev, struct usb_phy *xceiv) 2599 { 2600 unsigned tmp, buf; 2601 2602 /* abolish any previous hardware state */ 2603 omap_writew(0, UDC_SYSCON1); 2604 omap_writew(0, UDC_IRQ_EN); 2605 omap_writew(UDC_IRQ_SRC_MASK, UDC_IRQ_SRC); 2606 omap_writew(0, UDC_DMA_IRQ_EN); 2607 omap_writew(0, UDC_RXDMA_CFG); 2608 omap_writew(0, UDC_TXDMA_CFG); 2609 2610 /* UDC_PULLUP_EN gates the chip clock */ 2611 /* OTG_SYSCON_1 |= DEV_IDLE_EN; */ 2612 2613 udc = kzalloc(sizeof(*udc), GFP_KERNEL); 2614 if (!udc) 2615 return -ENOMEM; 2616 2617 spin_lock_init(&udc->lock); 2618 2619 udc->gadget.ops = &omap_gadget_ops; 2620 udc->gadget.ep0 = &udc->ep[0].ep; 2621 INIT_LIST_HEAD(&udc->gadget.ep_list); 2622 INIT_LIST_HEAD(&udc->iso); 2623 udc->gadget.speed = USB_SPEED_UNKNOWN; 2624 udc->gadget.max_speed = USB_SPEED_FULL; 2625 udc->gadget.name = driver_name; 2626 udc->transceiver = xceiv; 2627 2628 /* ep0 is special; put it right after the SETUP buffer */ 2629 buf = omap_ep_setup("ep0", 0, USB_ENDPOINT_XFER_CONTROL, 2630 8 /* after SETUP */, 64 /* maxpacket */, 0); 2631 list_del_init(&udc->ep[0].ep.ep_list); 2632 2633 /* initially disable all non-ep0 endpoints */ 2634 for (tmp = 1; tmp < 15; tmp++) { 2635 omap_writew(0, UDC_EP_RX(tmp)); 2636 omap_writew(0, UDC_EP_TX(tmp)); 2637 } 2638 2639 #define OMAP_BULK_EP(name, addr) \ 2640 buf = omap_ep_setup(name "-bulk", addr, \ 2641 USB_ENDPOINT_XFER_BULK, buf, 64, 1); 2642 #define OMAP_INT_EP(name, addr, maxp) \ 2643 buf = omap_ep_setup(name "-int", addr, \ 2644 USB_ENDPOINT_XFER_INT, buf, maxp, 0); 2645 #define OMAP_ISO_EP(name, addr, maxp) \ 2646 buf = omap_ep_setup(name "-iso", addr, \ 2647 USB_ENDPOINT_XFER_ISOC, buf, maxp, 1); 2648 2649 switch (fifo_mode) { 2650 case 0: 2651 OMAP_BULK_EP("ep1in", USB_DIR_IN | 1); 2652 OMAP_BULK_EP("ep2out", USB_DIR_OUT | 2); 2653 OMAP_INT_EP("ep3in", USB_DIR_IN | 3, 16); 2654 break; 2655 case 1: 2656 OMAP_BULK_EP("ep1in", USB_DIR_IN | 1); 2657 OMAP_BULK_EP("ep2out", USB_DIR_OUT | 2); 2658 OMAP_INT_EP("ep9in", USB_DIR_IN | 9, 16); 2659 2660 OMAP_BULK_EP("ep3in", USB_DIR_IN | 3); 2661 OMAP_BULK_EP("ep4out", USB_DIR_OUT | 4); 2662 OMAP_INT_EP("ep10in", USB_DIR_IN | 10, 16); 2663 2664 OMAP_BULK_EP("ep5in", USB_DIR_IN | 5); 2665 OMAP_BULK_EP("ep5out", USB_DIR_OUT | 5); 2666 OMAP_INT_EP("ep11in", USB_DIR_IN | 11, 16); 2667 2668 OMAP_BULK_EP("ep6in", USB_DIR_IN | 6); 2669 OMAP_BULK_EP("ep6out", USB_DIR_OUT | 6); 2670 OMAP_INT_EP("ep12in", USB_DIR_IN | 12, 16); 2671 2672 OMAP_BULK_EP("ep7in", USB_DIR_IN | 7); 2673 OMAP_BULK_EP("ep7out", USB_DIR_OUT | 7); 2674 OMAP_INT_EP("ep13in", USB_DIR_IN | 13, 16); 2675 OMAP_INT_EP("ep13out", USB_DIR_OUT | 13, 16); 2676 2677 OMAP_BULK_EP("ep8in", USB_DIR_IN | 8); 2678 OMAP_BULK_EP("ep8out", USB_DIR_OUT | 8); 2679 OMAP_INT_EP("ep14in", USB_DIR_IN | 14, 16); 2680 OMAP_INT_EP("ep14out", USB_DIR_OUT | 14, 16); 2681 2682 OMAP_BULK_EP("ep15in", USB_DIR_IN | 15); 2683 OMAP_BULK_EP("ep15out", USB_DIR_OUT | 15); 2684 2685 break; 2686 2687 #ifdef USE_ISO 2688 case 2: /* mixed iso/bulk */ 2689 OMAP_ISO_EP("ep1in", USB_DIR_IN | 1, 256); 2690 OMAP_ISO_EP("ep2out", USB_DIR_OUT | 2, 256); 2691 OMAP_ISO_EP("ep3in", USB_DIR_IN | 3, 128); 2692 OMAP_ISO_EP("ep4out", USB_DIR_OUT | 4, 128); 2693 2694 OMAP_INT_EP("ep5in", USB_DIR_IN | 5, 16); 2695 2696 OMAP_BULK_EP("ep6in", USB_DIR_IN | 6); 2697 OMAP_BULK_EP("ep7out", USB_DIR_OUT | 7); 2698 OMAP_INT_EP("ep8in", USB_DIR_IN | 8, 16); 2699 break; 2700 case 3: /* mixed bulk/iso */ 2701 OMAP_BULK_EP("ep1in", USB_DIR_IN | 1); 2702 OMAP_BULK_EP("ep2out", USB_DIR_OUT | 2); 2703 OMAP_INT_EP("ep3in", USB_DIR_IN | 3, 16); 2704 2705 OMAP_BULK_EP("ep4in", USB_DIR_IN | 4); 2706 OMAP_BULK_EP("ep5out", USB_DIR_OUT | 5); 2707 OMAP_INT_EP("ep6in", USB_DIR_IN | 6, 16); 2708 2709 OMAP_ISO_EP("ep7in", USB_DIR_IN | 7, 256); 2710 OMAP_ISO_EP("ep8out", USB_DIR_OUT | 8, 256); 2711 OMAP_INT_EP("ep9in", USB_DIR_IN | 9, 16); 2712 break; 2713 #endif 2714 2715 /* add more modes as needed */ 2716 2717 default: 2718 ERR("unsupported fifo_mode #%d\n", fifo_mode); 2719 return -ENODEV; 2720 } 2721 omap_writew(UDC_CFG_LOCK|UDC_SELF_PWR, UDC_SYSCON1); 2722 INFO("fifo mode %d, %d bytes not used\n", fifo_mode, 2048 - buf); 2723 return 0; 2724 } 2725 2726 static int omap_udc_probe(struct platform_device *pdev) 2727 { 2728 int status = -ENODEV; 2729 int hmc; 2730 struct usb_phy *xceiv = NULL; 2731 const char *type = NULL; 2732 struct omap_usb_config *config = dev_get_platdata(&pdev->dev); 2733 struct clk *dc_clk = NULL; 2734 struct clk *hhc_clk = NULL; 2735 2736 if (cpu_is_omap7xx()) 2737 use_dma = 0; 2738 2739 /* NOTE: "knows" the order of the resources! */ 2740 if (!request_mem_region(pdev->resource[0].start, 2741 pdev->resource[0].end - pdev->resource[0].start + 1, 2742 driver_name)) { 2743 DBG("request_mem_region failed\n"); 2744 return -EBUSY; 2745 } 2746 2747 if (cpu_is_omap16xx()) { 2748 dc_clk = clk_get(&pdev->dev, "usb_dc_ck"); 2749 hhc_clk = clk_get(&pdev->dev, "usb_hhc_ck"); 2750 BUG_ON(IS_ERR(dc_clk) || IS_ERR(hhc_clk)); 2751 /* can't use omap_udc_enable_clock yet */ 2752 clk_enable(dc_clk); 2753 clk_enable(hhc_clk); 2754 udelay(100); 2755 } 2756 2757 if (cpu_is_omap7xx()) { 2758 dc_clk = clk_get(&pdev->dev, "usb_dc_ck"); 2759 hhc_clk = clk_get(&pdev->dev, "l3_ocpi_ck"); 2760 BUG_ON(IS_ERR(dc_clk) || IS_ERR(hhc_clk)); 2761 /* can't use omap_udc_enable_clock yet */ 2762 clk_enable(dc_clk); 2763 clk_enable(hhc_clk); 2764 udelay(100); 2765 } 2766 2767 INFO("OMAP UDC rev %d.%d%s\n", 2768 omap_readw(UDC_REV) >> 4, omap_readw(UDC_REV) & 0xf, 2769 config->otg ? ", Mini-AB" : ""); 2770 2771 /* use the mode given to us by board init code */ 2772 if (cpu_is_omap15xx()) { 2773 hmc = HMC_1510; 2774 type = "(unknown)"; 2775 2776 if (machine_without_vbus_sense()) { 2777 /* just set up software VBUS detect, and then 2778 * later rig it so we always report VBUS. 2779 * FIXME without really sensing VBUS, we can't 2780 * know when to turn PULLUP_EN on/off; and that 2781 * means we always "need" the 48MHz clock. 2782 */ 2783 u32 tmp = omap_readl(FUNC_MUX_CTRL_0); 2784 tmp &= ~VBUS_CTRL_1510; 2785 omap_writel(tmp, FUNC_MUX_CTRL_0); 2786 tmp |= VBUS_MODE_1510; 2787 tmp &= ~VBUS_CTRL_1510; 2788 omap_writel(tmp, FUNC_MUX_CTRL_0); 2789 } 2790 } else { 2791 /* The transceiver may package some GPIO logic or handle 2792 * loopback and/or transceiverless setup; if we find one, 2793 * use it. Except for OTG, we don't _need_ to talk to one; 2794 * but not having one probably means no VBUS detection. 2795 */ 2796 xceiv = usb_get_phy(USB_PHY_TYPE_USB2); 2797 if (!IS_ERR_OR_NULL(xceiv)) 2798 type = xceiv->label; 2799 else if (config->otg) { 2800 DBG("OTG requires external transceiver!\n"); 2801 goto cleanup0; 2802 } 2803 2804 hmc = HMC_1610; 2805 2806 switch (hmc) { 2807 case 0: /* POWERUP DEFAULT == 0 */ 2808 case 4: 2809 case 12: 2810 case 20: 2811 if (!cpu_is_omap1710()) { 2812 type = "integrated"; 2813 break; 2814 } 2815 /* FALL THROUGH */ 2816 case 3: 2817 case 11: 2818 case 16: 2819 case 19: 2820 case 25: 2821 if (IS_ERR_OR_NULL(xceiv)) { 2822 DBG("external transceiver not registered!\n"); 2823 type = "unknown"; 2824 } 2825 break; 2826 case 21: /* internal loopback */ 2827 type = "loopback"; 2828 break; 2829 case 14: /* transceiverless */ 2830 if (cpu_is_omap1710()) 2831 goto bad_on_1710; 2832 /* FALL THROUGH */ 2833 case 13: 2834 case 15: 2835 type = "no"; 2836 break; 2837 2838 default: 2839 bad_on_1710: 2840 ERR("unrecognized UDC HMC mode %d\n", hmc); 2841 goto cleanup0; 2842 } 2843 } 2844 2845 INFO("hmc mode %d, %s transceiver\n", hmc, type); 2846 2847 /* a "gadget" abstracts/virtualizes the controller */ 2848 status = omap_udc_setup(pdev, xceiv); 2849 if (status) 2850 goto cleanup0; 2851 2852 xceiv = NULL; 2853 /* "udc" is now valid */ 2854 pullup_disable(udc); 2855 #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) 2856 udc->gadget.is_otg = (config->otg != 0); 2857 #endif 2858 2859 /* starting with omap1710 es2.0, clear toggle is a separate bit */ 2860 if (omap_readw(UDC_REV) >= 0x61) 2861 udc->clr_halt = UDC_RESET_EP | UDC_CLRDATA_TOGGLE; 2862 else 2863 udc->clr_halt = UDC_RESET_EP; 2864 2865 /* USB general purpose IRQ: ep0, state changes, dma, etc */ 2866 status = request_irq(pdev->resource[1].start, omap_udc_irq, 2867 0, driver_name, udc); 2868 if (status != 0) { 2869 ERR("can't get irq %d, err %d\n", 2870 (int) pdev->resource[1].start, status); 2871 goto cleanup1; 2872 } 2873 2874 /* USB "non-iso" IRQ (PIO for all but ep0) */ 2875 status = request_irq(pdev->resource[2].start, omap_udc_pio_irq, 2876 0, "omap_udc pio", udc); 2877 if (status != 0) { 2878 ERR("can't get irq %d, err %d\n", 2879 (int) pdev->resource[2].start, status); 2880 goto cleanup2; 2881 } 2882 #ifdef USE_ISO 2883 status = request_irq(pdev->resource[3].start, omap_udc_iso_irq, 2884 0, "omap_udc iso", udc); 2885 if (status != 0) { 2886 ERR("can't get irq %d, err %d\n", 2887 (int) pdev->resource[3].start, status); 2888 goto cleanup3; 2889 } 2890 #endif 2891 if (cpu_is_omap16xx() || cpu_is_omap7xx()) { 2892 udc->dc_clk = dc_clk; 2893 udc->hhc_clk = hhc_clk; 2894 clk_disable(hhc_clk); 2895 clk_disable(dc_clk); 2896 } 2897 2898 create_proc_file(); 2899 status = usb_add_gadget_udc_release(&pdev->dev, &udc->gadget, 2900 omap_udc_release); 2901 if (status) 2902 goto cleanup4; 2903 2904 return 0; 2905 2906 cleanup4: 2907 remove_proc_file(); 2908 2909 #ifdef USE_ISO 2910 cleanup3: 2911 free_irq(pdev->resource[2].start, udc); 2912 #endif 2913 2914 cleanup2: 2915 free_irq(pdev->resource[1].start, udc); 2916 2917 cleanup1: 2918 kfree(udc); 2919 udc = NULL; 2920 2921 cleanup0: 2922 if (!IS_ERR_OR_NULL(xceiv)) 2923 usb_put_phy(xceiv); 2924 2925 if (cpu_is_omap16xx() || cpu_is_omap7xx()) { 2926 clk_disable(hhc_clk); 2927 clk_disable(dc_clk); 2928 clk_put(hhc_clk); 2929 clk_put(dc_clk); 2930 } 2931 2932 release_mem_region(pdev->resource[0].start, 2933 pdev->resource[0].end - pdev->resource[0].start + 1); 2934 2935 return status; 2936 } 2937 2938 static int omap_udc_remove(struct platform_device *pdev) 2939 { 2940 DECLARE_COMPLETION_ONSTACK(done); 2941 2942 if (!udc) 2943 return -ENODEV; 2944 2945 usb_del_gadget_udc(&udc->gadget); 2946 if (udc->driver) 2947 return -EBUSY; 2948 2949 udc->done = &done; 2950 2951 pullup_disable(udc); 2952 if (!IS_ERR_OR_NULL(udc->transceiver)) { 2953 usb_put_phy(udc->transceiver); 2954 udc->transceiver = NULL; 2955 } 2956 omap_writew(0, UDC_SYSCON1); 2957 2958 remove_proc_file(); 2959 2960 #ifdef USE_ISO 2961 free_irq(pdev->resource[3].start, udc); 2962 #endif 2963 free_irq(pdev->resource[2].start, udc); 2964 free_irq(pdev->resource[1].start, udc); 2965 2966 if (udc->dc_clk) { 2967 if (udc->clk_requested) 2968 omap_udc_enable_clock(0); 2969 clk_put(udc->hhc_clk); 2970 clk_put(udc->dc_clk); 2971 } 2972 2973 release_mem_region(pdev->resource[0].start, 2974 pdev->resource[0].end - pdev->resource[0].start + 1); 2975 2976 wait_for_completion(&done); 2977 2978 return 0; 2979 } 2980 2981 /* suspend/resume/wakeup from sysfs (echo > power/state) or when the 2982 * system is forced into deep sleep 2983 * 2984 * REVISIT we should probably reject suspend requests when there's a host 2985 * session active, rather than disconnecting, at least on boards that can 2986 * report VBUS irqs (UDC_DEVSTAT.UDC_ATT). And in any case, we need to 2987 * make host resumes and VBUS detection trigger OMAP wakeup events; that 2988 * may involve talking to an external transceiver (e.g. isp1301). 2989 */ 2990 2991 static int omap_udc_suspend(struct platform_device *dev, pm_message_t message) 2992 { 2993 u32 devstat; 2994 2995 devstat = omap_readw(UDC_DEVSTAT); 2996 2997 /* we're requesting 48 MHz clock if the pullup is enabled 2998 * (== we're attached to the host) and we're not suspended, 2999 * which would prevent entry to deep sleep... 3000 */ 3001 if ((devstat & UDC_ATT) != 0 && (devstat & UDC_SUS) == 0) { 3002 WARNING("session active; suspend requires disconnect\n"); 3003 omap_pullup(&udc->gadget, 0); 3004 } 3005 3006 return 0; 3007 } 3008 3009 static int omap_udc_resume(struct platform_device *dev) 3010 { 3011 DBG("resume + wakeup/SRP\n"); 3012 omap_pullup(&udc->gadget, 1); 3013 3014 /* maybe the host would enumerate us if we nudged it */ 3015 msleep(100); 3016 return omap_wakeup(&udc->gadget); 3017 } 3018 3019 /*-------------------------------------------------------------------------*/ 3020 3021 static struct platform_driver udc_driver = { 3022 .probe = omap_udc_probe, 3023 .remove = omap_udc_remove, 3024 .suspend = omap_udc_suspend, 3025 .resume = omap_udc_resume, 3026 .driver = { 3027 .name = (char *) driver_name, 3028 }, 3029 }; 3030 3031 module_platform_driver(udc_driver); 3032 3033 MODULE_DESCRIPTION(DRIVER_DESC); 3034 MODULE_LICENSE("GPL"); 3035 MODULE_ALIAS("platform:omap_udc"); 3036