1 /* 2 * Copyright (C) 2004,2012 Freescale Semiconductor, Inc 3 * All rights reserved. 4 * 5 * This program is free software; you can redistribute it and/or modify it 6 * under the terms of the GNU General Public License as published by the 7 * Free Software Foundation; either version 2 of the License, or (at your 8 * option) any later version. 9 * 10 * Freescale USB device/endpoint management registers 11 */ 12 #ifndef __FSL_USB2_UDC_H 13 #define __FSL_USB2_UDC_H 14 15 #include <linux/usb/ch9.h> 16 #include <linux/usb/gadget.h> 17 18 /* ### define USB registers here 19 */ 20 #define USB_MAX_CTRL_PAYLOAD 64 21 #define USB_DR_SYS_OFFSET 0x400 22 23 /* USB DR device mode registers (Little Endian) */ 24 struct usb_dr_device { 25 /* Capability register */ 26 u8 res1[256]; 27 u16 caplength; /* Capability Register Length */ 28 u16 hciversion; /* Host Controller Interface Version */ 29 u32 hcsparams; /* Host Controller Structural Parameters */ 30 u32 hccparams; /* Host Controller Capability Parameters */ 31 u8 res2[20]; 32 u32 dciversion; /* Device Controller Interface Version */ 33 u32 dccparams; /* Device Controller Capability Parameters */ 34 u8 res3[24]; 35 /* Operation register */ 36 u32 usbcmd; /* USB Command Register */ 37 u32 usbsts; /* USB Status Register */ 38 u32 usbintr; /* USB Interrupt Enable Register */ 39 u32 frindex; /* Frame Index Register */ 40 u8 res4[4]; 41 u32 deviceaddr; /* Device Address */ 42 u32 endpointlistaddr; /* Endpoint List Address Register */ 43 u8 res5[4]; 44 u32 burstsize; /* Master Interface Data Burst Size Register */ 45 u32 txttfilltuning; /* Transmit FIFO Tuning Controls Register */ 46 u8 res6[24]; 47 u32 configflag; /* Configure Flag Register */ 48 u32 portsc1; /* Port 1 Status and Control Register */ 49 u8 res7[28]; 50 u32 otgsc; /* On-The-Go Status and Control */ 51 u32 usbmode; /* USB Mode Register */ 52 u32 endptsetupstat; /* Endpoint Setup Status Register */ 53 u32 endpointprime; /* Endpoint Initialization Register */ 54 u32 endptflush; /* Endpoint Flush Register */ 55 u32 endptstatus; /* Endpoint Status Register */ 56 u32 endptcomplete; /* Endpoint Complete Register */ 57 u32 endptctrl[6]; /* Endpoint Control Registers */ 58 }; 59 60 /* USB DR host mode registers (Little Endian) */ 61 struct usb_dr_host { 62 /* Capability register */ 63 u8 res1[256]; 64 u16 caplength; /* Capability Register Length */ 65 u16 hciversion; /* Host Controller Interface Version */ 66 u32 hcsparams; /* Host Controller Structural Parameters */ 67 u32 hccparams; /* Host Controller Capability Parameters */ 68 u8 res2[20]; 69 u32 dciversion; /* Device Controller Interface Version */ 70 u32 dccparams; /* Device Controller Capability Parameters */ 71 u8 res3[24]; 72 /* Operation register */ 73 u32 usbcmd; /* USB Command Register */ 74 u32 usbsts; /* USB Status Register */ 75 u32 usbintr; /* USB Interrupt Enable Register */ 76 u32 frindex; /* Frame Index Register */ 77 u8 res4[4]; 78 u32 periodiclistbase; /* Periodic Frame List Base Address Register */ 79 u32 asynclistaddr; /* Current Asynchronous List Address Register */ 80 u8 res5[4]; 81 u32 burstsize; /* Master Interface Data Burst Size Register */ 82 u32 txttfilltuning; /* Transmit FIFO Tuning Controls Register */ 83 u8 res6[24]; 84 u32 configflag; /* Configure Flag Register */ 85 u32 portsc1; /* Port 1 Status and Control Register */ 86 u8 res7[28]; 87 u32 otgsc; /* On-The-Go Status and Control */ 88 u32 usbmode; /* USB Mode Register */ 89 u32 endptsetupstat; /* Endpoint Setup Status Register */ 90 u32 endpointprime; /* Endpoint Initialization Register */ 91 u32 endptflush; /* Endpoint Flush Register */ 92 u32 endptstatus; /* Endpoint Status Register */ 93 u32 endptcomplete; /* Endpoint Complete Register */ 94 u32 endptctrl[6]; /* Endpoint Control Registers */ 95 }; 96 97 /* non-EHCI USB system interface registers (Big Endian) */ 98 struct usb_sys_interface { 99 u32 snoop1; 100 u32 snoop2; 101 u32 age_cnt_thresh; /* Age Count Threshold Register */ 102 u32 pri_ctrl; /* Priority Control Register */ 103 u32 si_ctrl; /* System Interface Control Register */ 104 u8 res[236]; 105 u32 control; /* General Purpose Control Register */ 106 }; 107 108 /* ep0 transfer state */ 109 #define WAIT_FOR_SETUP 0 110 #define DATA_STATE_XMIT 1 111 #define DATA_STATE_NEED_ZLP 2 112 #define WAIT_FOR_OUT_STATUS 3 113 #define DATA_STATE_RECV 4 114 115 /* Device Controller Capability Parameter register */ 116 #define DCCPARAMS_DC 0x00000080 117 #define DCCPARAMS_DEN_MASK 0x0000001f 118 119 /* Frame Index Register Bit Masks */ 120 #define USB_FRINDEX_MASKS 0x3fff 121 /* USB CMD Register Bit Masks */ 122 #define USB_CMD_RUN_STOP 0x00000001 123 #define USB_CMD_CTRL_RESET 0x00000002 124 #define USB_CMD_PERIODIC_SCHEDULE_EN 0x00000010 125 #define USB_CMD_ASYNC_SCHEDULE_EN 0x00000020 126 #define USB_CMD_INT_AA_DOORBELL 0x00000040 127 #define USB_CMD_ASP 0x00000300 128 #define USB_CMD_ASYNC_SCH_PARK_EN 0x00000800 129 #define USB_CMD_SUTW 0x00002000 130 #define USB_CMD_ATDTW 0x00004000 131 #define USB_CMD_ITC 0x00FF0000 132 133 /* bit 15,3,2 are frame list size */ 134 #define USB_CMD_FRAME_SIZE_1024 0x00000000 135 #define USB_CMD_FRAME_SIZE_512 0x00000004 136 #define USB_CMD_FRAME_SIZE_256 0x00000008 137 #define USB_CMD_FRAME_SIZE_128 0x0000000C 138 #define USB_CMD_FRAME_SIZE_64 0x00008000 139 #define USB_CMD_FRAME_SIZE_32 0x00008004 140 #define USB_CMD_FRAME_SIZE_16 0x00008008 141 #define USB_CMD_FRAME_SIZE_8 0x0000800C 142 143 /* bit 9-8 are async schedule park mode count */ 144 #define USB_CMD_ASP_00 0x00000000 145 #define USB_CMD_ASP_01 0x00000100 146 #define USB_CMD_ASP_10 0x00000200 147 #define USB_CMD_ASP_11 0x00000300 148 #define USB_CMD_ASP_BIT_POS 8 149 150 /* bit 23-16 are interrupt threshold control */ 151 #define USB_CMD_ITC_NO_THRESHOLD 0x00000000 152 #define USB_CMD_ITC_1_MICRO_FRM 0x00010000 153 #define USB_CMD_ITC_2_MICRO_FRM 0x00020000 154 #define USB_CMD_ITC_4_MICRO_FRM 0x00040000 155 #define USB_CMD_ITC_8_MICRO_FRM 0x00080000 156 #define USB_CMD_ITC_16_MICRO_FRM 0x00100000 157 #define USB_CMD_ITC_32_MICRO_FRM 0x00200000 158 #define USB_CMD_ITC_64_MICRO_FRM 0x00400000 159 #define USB_CMD_ITC_BIT_POS 16 160 161 /* USB STS Register Bit Masks */ 162 #define USB_STS_INT 0x00000001 163 #define USB_STS_ERR 0x00000002 164 #define USB_STS_PORT_CHANGE 0x00000004 165 #define USB_STS_FRM_LST_ROLL 0x00000008 166 #define USB_STS_SYS_ERR 0x00000010 167 #define USB_STS_IAA 0x00000020 168 #define USB_STS_RESET 0x00000040 169 #define USB_STS_SOF 0x00000080 170 #define USB_STS_SUSPEND 0x00000100 171 #define USB_STS_HC_HALTED 0x00001000 172 #define USB_STS_RCL 0x00002000 173 #define USB_STS_PERIODIC_SCHEDULE 0x00004000 174 #define USB_STS_ASYNC_SCHEDULE 0x00008000 175 176 /* USB INTR Register Bit Masks */ 177 #define USB_INTR_INT_EN 0x00000001 178 #define USB_INTR_ERR_INT_EN 0x00000002 179 #define USB_INTR_PTC_DETECT_EN 0x00000004 180 #define USB_INTR_FRM_LST_ROLL_EN 0x00000008 181 #define USB_INTR_SYS_ERR_EN 0x00000010 182 #define USB_INTR_ASYN_ADV_EN 0x00000020 183 #define USB_INTR_RESET_EN 0x00000040 184 #define USB_INTR_SOF_EN 0x00000080 185 #define USB_INTR_DEVICE_SUSPEND 0x00000100 186 187 /* Device Address bit masks */ 188 #define USB_DEVICE_ADDRESS_MASK 0xFE000000 189 #define USB_DEVICE_ADDRESS_BIT_POS 25 190 191 /* endpoint list address bit masks */ 192 #define USB_EP_LIST_ADDRESS_MASK 0xfffff800 193 194 /* PORTSCX Register Bit Masks */ 195 #define PORTSCX_CURRENT_CONNECT_STATUS 0x00000001 196 #define PORTSCX_CONNECT_STATUS_CHANGE 0x00000002 197 #define PORTSCX_PORT_ENABLE 0x00000004 198 #define PORTSCX_PORT_EN_DIS_CHANGE 0x00000008 199 #define PORTSCX_OVER_CURRENT_ACT 0x00000010 200 #define PORTSCX_OVER_CURRENT_CHG 0x00000020 201 #define PORTSCX_PORT_FORCE_RESUME 0x00000040 202 #define PORTSCX_PORT_SUSPEND 0x00000080 203 #define PORTSCX_PORT_RESET 0x00000100 204 #define PORTSCX_LINE_STATUS_BITS 0x00000C00 205 #define PORTSCX_PORT_POWER 0x00001000 206 #define PORTSCX_PORT_INDICTOR_CTRL 0x0000C000 207 #define PORTSCX_PORT_TEST_CTRL 0x000F0000 208 #define PORTSCX_WAKE_ON_CONNECT_EN 0x00100000 209 #define PORTSCX_WAKE_ON_CONNECT_DIS 0x00200000 210 #define PORTSCX_WAKE_ON_OVER_CURRENT 0x00400000 211 #define PORTSCX_PHY_LOW_POWER_SPD 0x00800000 212 #define PORTSCX_PORT_FORCE_FULL_SPEED 0x01000000 213 #define PORTSCX_PORT_SPEED_MASK 0x0C000000 214 #define PORTSCX_PORT_WIDTH 0x10000000 215 #define PORTSCX_PHY_TYPE_SEL 0xC0000000 216 217 /* bit 11-10 are line status */ 218 #define PORTSCX_LINE_STATUS_SE0 0x00000000 219 #define PORTSCX_LINE_STATUS_JSTATE 0x00000400 220 #define PORTSCX_LINE_STATUS_KSTATE 0x00000800 221 #define PORTSCX_LINE_STATUS_UNDEF 0x00000C00 222 #define PORTSCX_LINE_STATUS_BIT_POS 10 223 224 /* bit 15-14 are port indicator control */ 225 #define PORTSCX_PIC_OFF 0x00000000 226 #define PORTSCX_PIC_AMBER 0x00004000 227 #define PORTSCX_PIC_GREEN 0x00008000 228 #define PORTSCX_PIC_UNDEF 0x0000C000 229 #define PORTSCX_PIC_BIT_POS 14 230 231 /* bit 19-16 are port test control */ 232 #define PORTSCX_PTC_DISABLE 0x00000000 233 #define PORTSCX_PTC_JSTATE 0x00010000 234 #define PORTSCX_PTC_KSTATE 0x00020000 235 #define PORTSCX_PTC_SEQNAK 0x00030000 236 #define PORTSCX_PTC_PACKET 0x00040000 237 #define PORTSCX_PTC_FORCE_EN 0x00050000 238 #define PORTSCX_PTC_BIT_POS 16 239 240 /* bit 27-26 are port speed */ 241 #define PORTSCX_PORT_SPEED_FULL 0x00000000 242 #define PORTSCX_PORT_SPEED_LOW 0x04000000 243 #define PORTSCX_PORT_SPEED_HIGH 0x08000000 244 #define PORTSCX_PORT_SPEED_UNDEF 0x0C000000 245 #define PORTSCX_SPEED_BIT_POS 26 246 247 /* bit 28 is parallel transceiver width for UTMI interface */ 248 #define PORTSCX_PTW 0x10000000 249 #define PORTSCX_PTW_8BIT 0x00000000 250 #define PORTSCX_PTW_16BIT 0x10000000 251 252 /* bit 31-30 are port transceiver select */ 253 #define PORTSCX_PTS_UTMI 0x00000000 254 #define PORTSCX_PTS_ULPI 0x80000000 255 #define PORTSCX_PTS_FSLS 0xC0000000 256 #define PORTSCX_PTS_BIT_POS 30 257 258 /* otgsc Register Bit Masks */ 259 #define OTGSC_CTRL_VUSB_DISCHARGE 0x00000001 260 #define OTGSC_CTRL_VUSB_CHARGE 0x00000002 261 #define OTGSC_CTRL_OTG_TERM 0x00000008 262 #define OTGSC_CTRL_DATA_PULSING 0x00000010 263 #define OTGSC_STS_USB_ID 0x00000100 264 #define OTGSC_STS_A_VBUS_VALID 0x00000200 265 #define OTGSC_STS_A_SESSION_VALID 0x00000400 266 #define OTGSC_STS_B_SESSION_VALID 0x00000800 267 #define OTGSC_STS_B_SESSION_END 0x00001000 268 #define OTGSC_STS_1MS_TOGGLE 0x00002000 269 #define OTGSC_STS_DATA_PULSING 0x00004000 270 #define OTGSC_INTSTS_USB_ID 0x00010000 271 #define OTGSC_INTSTS_A_VBUS_VALID 0x00020000 272 #define OTGSC_INTSTS_A_SESSION_VALID 0x00040000 273 #define OTGSC_INTSTS_B_SESSION_VALID 0x00080000 274 #define OTGSC_INTSTS_B_SESSION_END 0x00100000 275 #define OTGSC_INTSTS_1MS 0x00200000 276 #define OTGSC_INTSTS_DATA_PULSING 0x00400000 277 #define OTGSC_INTR_USB_ID 0x01000000 278 #define OTGSC_INTR_A_VBUS_VALID 0x02000000 279 #define OTGSC_INTR_A_SESSION_VALID 0x04000000 280 #define OTGSC_INTR_B_SESSION_VALID 0x08000000 281 #define OTGSC_INTR_B_SESSION_END 0x10000000 282 #define OTGSC_INTR_1MS_TIMER 0x20000000 283 #define OTGSC_INTR_DATA_PULSING 0x40000000 284 285 /* USB MODE Register Bit Masks */ 286 #define USB_MODE_CTRL_MODE_IDLE 0x00000000 287 #define USB_MODE_CTRL_MODE_DEVICE 0x00000002 288 #define USB_MODE_CTRL_MODE_HOST 0x00000003 289 #define USB_MODE_CTRL_MODE_MASK 0x00000003 290 #define USB_MODE_CTRL_MODE_RSV 0x00000001 291 #define USB_MODE_ES 0x00000004 /* Endian Select */ 292 #define USB_MODE_SETUP_LOCK_OFF 0x00000008 293 #define USB_MODE_STREAM_DISABLE 0x00000010 294 /* Endpoint Flush Register */ 295 #define EPFLUSH_TX_OFFSET 0x00010000 296 #define EPFLUSH_RX_OFFSET 0x00000000 297 298 /* Endpoint Setup Status bit masks */ 299 #define EP_SETUP_STATUS_MASK 0x0000003F 300 #define EP_SETUP_STATUS_EP0 0x00000001 301 302 /* ENDPOINTCTRLx Register Bit Masks */ 303 #define EPCTRL_TX_ENABLE 0x00800000 304 #define EPCTRL_TX_DATA_TOGGLE_RST 0x00400000 /* Not EP0 */ 305 #define EPCTRL_TX_DATA_TOGGLE_INH 0x00200000 /* Not EP0 */ 306 #define EPCTRL_TX_TYPE 0x000C0000 307 #define EPCTRL_TX_DATA_SOURCE 0x00020000 /* Not EP0 */ 308 #define EPCTRL_TX_EP_STALL 0x00010000 309 #define EPCTRL_RX_ENABLE 0x00000080 310 #define EPCTRL_RX_DATA_TOGGLE_RST 0x00000040 /* Not EP0 */ 311 #define EPCTRL_RX_DATA_TOGGLE_INH 0x00000020 /* Not EP0 */ 312 #define EPCTRL_RX_TYPE 0x0000000C 313 #define EPCTRL_RX_DATA_SINK 0x00000002 /* Not EP0 */ 314 #define EPCTRL_RX_EP_STALL 0x00000001 315 316 /* bit 19-18 and 3-2 are endpoint type */ 317 #define EPCTRL_EP_TYPE_CONTROL 0 318 #define EPCTRL_EP_TYPE_ISO 1 319 #define EPCTRL_EP_TYPE_BULK 2 320 #define EPCTRL_EP_TYPE_INTERRUPT 3 321 #define EPCTRL_TX_EP_TYPE_SHIFT 18 322 #define EPCTRL_RX_EP_TYPE_SHIFT 2 323 324 /* SNOOPn Register Bit Masks */ 325 #define SNOOP_ADDRESS_MASK 0xFFFFF000 326 #define SNOOP_SIZE_ZERO 0x00 /* snooping disable */ 327 #define SNOOP_SIZE_4KB 0x0B /* 4KB snoop size */ 328 #define SNOOP_SIZE_8KB 0x0C 329 #define SNOOP_SIZE_16KB 0x0D 330 #define SNOOP_SIZE_32KB 0x0E 331 #define SNOOP_SIZE_64KB 0x0F 332 #define SNOOP_SIZE_128KB 0x10 333 #define SNOOP_SIZE_256KB 0x11 334 #define SNOOP_SIZE_512KB 0x12 335 #define SNOOP_SIZE_1MB 0x13 336 #define SNOOP_SIZE_2MB 0x14 337 #define SNOOP_SIZE_4MB 0x15 338 #define SNOOP_SIZE_8MB 0x16 339 #define SNOOP_SIZE_16MB 0x17 340 #define SNOOP_SIZE_32MB 0x18 341 #define SNOOP_SIZE_64MB 0x19 342 #define SNOOP_SIZE_128MB 0x1A 343 #define SNOOP_SIZE_256MB 0x1B 344 #define SNOOP_SIZE_512MB 0x1C 345 #define SNOOP_SIZE_1GB 0x1D 346 #define SNOOP_SIZE_2GB 0x1E /* 2GB snoop size */ 347 348 /* pri_ctrl Register Bit Masks */ 349 #define PRI_CTRL_PRI_LVL1 0x0000000C 350 #define PRI_CTRL_PRI_LVL0 0x00000003 351 352 /* si_ctrl Register Bit Masks */ 353 #define SI_CTRL_ERR_DISABLE 0x00000010 354 #define SI_CTRL_IDRC_DISABLE 0x00000008 355 #define SI_CTRL_RD_SAFE_EN 0x00000004 356 #define SI_CTRL_RD_PREFETCH_DISABLE 0x00000002 357 #define SI_CTRL_RD_PREFEFETCH_VAL 0x00000001 358 359 /* control Register Bit Masks */ 360 #define USB_CTRL_IOENB 0x00000004 361 #define USB_CTRL_ULPI_INT0EN 0x00000001 362 #define USB_CTRL_UTMI_PHY_EN 0x00000200 363 #define USB_CTRL_USB_EN 0x00000004 364 #define USB_CTRL_ULPI_PHY_CLK_SEL 0x00000400 365 366 /* Endpoint Queue Head data struct 367 * Rem: all the variables of qh are LittleEndian Mode 368 * and NEXT_POINTER_MASK should operate on a LittleEndian, Phy Addr 369 */ 370 struct ep_queue_head { 371 u32 max_pkt_length; /* Mult(31-30) , Zlt(29) , Max Pkt len 372 and IOS(15) */ 373 u32 curr_dtd_ptr; /* Current dTD Pointer(31-5) */ 374 u32 next_dtd_ptr; /* Next dTD Pointer(31-5), T(0) */ 375 u32 size_ioc_int_sts; /* Total bytes (30-16), IOC (15), 376 MultO(11-10), STS (7-0) */ 377 u32 buff_ptr0; /* Buffer pointer Page 0 (31-12) */ 378 u32 buff_ptr1; /* Buffer pointer Page 1 (31-12) */ 379 u32 buff_ptr2; /* Buffer pointer Page 2 (31-12) */ 380 u32 buff_ptr3; /* Buffer pointer Page 3 (31-12) */ 381 u32 buff_ptr4; /* Buffer pointer Page 4 (31-12) */ 382 u32 res1; 383 u8 setup_buffer[8]; /* Setup data 8 bytes */ 384 u32 res2[4]; 385 }; 386 387 /* Endpoint Queue Head Bit Masks */ 388 #define EP_QUEUE_HEAD_MULT_POS 30 389 #define EP_QUEUE_HEAD_ZLT_SEL 0x20000000 390 #define EP_QUEUE_HEAD_MAX_PKT_LEN_POS 16 391 #define EP_QUEUE_HEAD_MAX_PKT_LEN(ep_info) (((ep_info)>>16)&0x07ff) 392 #define EP_QUEUE_HEAD_IOS 0x00008000 393 #define EP_QUEUE_HEAD_NEXT_TERMINATE 0x00000001 394 #define EP_QUEUE_HEAD_IOC 0x00008000 395 #define EP_QUEUE_HEAD_MULTO 0x00000C00 396 #define EP_QUEUE_HEAD_STATUS_HALT 0x00000040 397 #define EP_QUEUE_HEAD_STATUS_ACTIVE 0x00000080 398 #define EP_QUEUE_CURRENT_OFFSET_MASK 0x00000FFF 399 #define EP_QUEUE_HEAD_NEXT_POINTER_MASK 0xFFFFFFE0 400 #define EP_QUEUE_FRINDEX_MASK 0x000007FF 401 #define EP_MAX_LENGTH_TRANSFER 0x4000 402 403 /* Endpoint Transfer Descriptor data struct */ 404 /* Rem: all the variables of td are LittleEndian Mode */ 405 struct ep_td_struct { 406 u32 next_td_ptr; /* Next TD pointer(31-5), T(0) set 407 indicate invalid */ 408 u32 size_ioc_sts; /* Total bytes (30-16), IOC (15), 409 MultO(11-10), STS (7-0) */ 410 u32 buff_ptr0; /* Buffer pointer Page 0 */ 411 u32 buff_ptr1; /* Buffer pointer Page 1 */ 412 u32 buff_ptr2; /* Buffer pointer Page 2 */ 413 u32 buff_ptr3; /* Buffer pointer Page 3 */ 414 u32 buff_ptr4; /* Buffer pointer Page 4 */ 415 u32 res; 416 /* 32 bytes */ 417 dma_addr_t td_dma; /* dma address for this td */ 418 /* virtual address of next td specified in next_td_ptr */ 419 struct ep_td_struct *next_td_virt; 420 }; 421 422 /* Endpoint Transfer Descriptor bit Masks */ 423 #define DTD_NEXT_TERMINATE 0x00000001 424 #define DTD_IOC 0x00008000 425 #define DTD_STATUS_ACTIVE 0x00000080 426 #define DTD_STATUS_HALTED 0x00000040 427 #define DTD_STATUS_DATA_BUFF_ERR 0x00000020 428 #define DTD_STATUS_TRANSACTION_ERR 0x00000008 429 #define DTD_RESERVED_FIELDS 0x80007300 430 #define DTD_ADDR_MASK 0xFFFFFFE0 431 #define DTD_PACKET_SIZE 0x7FFF0000 432 #define DTD_LENGTH_BIT_POS 16 433 #define DTD_ERROR_MASK (DTD_STATUS_HALTED | \ 434 DTD_STATUS_DATA_BUFF_ERR | \ 435 DTD_STATUS_TRANSACTION_ERR) 436 /* Alignment requirements; must be a power of two */ 437 #define DTD_ALIGNMENT 0x20 438 #define QH_ALIGNMENT 2048 439 440 /* Controller dma boundary */ 441 #define UDC_DMA_BOUNDARY 0x1000 442 443 /*-------------------------------------------------------------------------*/ 444 445 /* ### driver private data 446 */ 447 struct fsl_req { 448 struct usb_request req; 449 struct list_head queue; 450 /* ep_queue() func will add 451 a request->queue into a udc_ep->queue 'd tail */ 452 struct fsl_ep *ep; 453 unsigned mapped:1; 454 455 struct ep_td_struct *head, *tail; /* For dTD List 456 cpu endian Virtual addr */ 457 unsigned int dtd_count; 458 }; 459 460 #define REQ_UNCOMPLETE 1 461 462 struct fsl_ep { 463 struct usb_ep ep; 464 struct list_head queue; 465 struct fsl_udc *udc; 466 struct ep_queue_head *qh; 467 struct usb_gadget *gadget; 468 469 char name[14]; 470 unsigned stopped:1; 471 }; 472 473 #define EP_DIR_IN 1 474 #define EP_DIR_OUT 0 475 476 struct fsl_udc { 477 struct usb_gadget gadget; 478 struct usb_gadget_driver *driver; 479 struct fsl_usb2_platform_data *pdata; 480 struct completion *done; /* to make sure release() is done */ 481 struct fsl_ep *eps; 482 unsigned int max_ep; 483 unsigned int irq; 484 485 struct usb_ctrlrequest local_setup_buff; 486 spinlock_t lock; 487 struct usb_phy *transceiver; 488 unsigned softconnect:1; 489 unsigned vbus_active:1; 490 unsigned stopped:1; 491 unsigned remote_wakeup:1; 492 unsigned already_stopped:1; 493 unsigned big_endian_desc:1; 494 495 struct ep_queue_head *ep_qh; /* Endpoints Queue-Head */ 496 struct fsl_req *status_req; /* ep0 status request */ 497 struct dma_pool *td_pool; /* dma pool for DTD */ 498 enum fsl_usb2_phy_modes phy_mode; 499 500 size_t ep_qh_size; /* size after alignment adjustment*/ 501 dma_addr_t ep_qh_dma; /* dma address of QH */ 502 503 u32 max_pipes; /* Device max pipes */ 504 u32 bus_reset; /* Device is bus resetting */ 505 u32 resume_state; /* USB state to resume */ 506 u32 usb_state; /* USB current state */ 507 u32 ep0_state; /* Endpoint zero state */ 508 u32 ep0_dir; /* Endpoint zero direction: can be 509 USB_DIR_IN or USB_DIR_OUT */ 510 u8 device_address; /* Device USB address */ 511 }; 512 513 /*-------------------------------------------------------------------------*/ 514 515 #ifdef DEBUG 516 #define DBG(fmt, args...) printk(KERN_DEBUG "[%s] " fmt "\n", \ 517 __func__, ## args) 518 #else 519 #define DBG(fmt, args...) do{}while(0) 520 #endif 521 522 #if 0 523 static void dump_msg(const char *label, const u8 * buf, unsigned int length) 524 { 525 unsigned int start, num, i; 526 char line[52], *p; 527 528 if (length >= 512) 529 return; 530 DBG("%s, length %u:\n", label, length); 531 start = 0; 532 while (length > 0) { 533 num = min(length, 16u); 534 p = line; 535 for (i = 0; i < num; ++i) { 536 if (i == 8) 537 *p++ = ' '; 538 sprintf(p, " %02x", buf[i]); 539 p += 3; 540 } 541 *p = 0; 542 printk(KERN_DEBUG "%6x: %s\n", start, line); 543 buf += num; 544 start += num; 545 length -= num; 546 } 547 } 548 #endif 549 550 #ifdef VERBOSE 551 #define VDBG DBG 552 #else 553 #define VDBG(stuff...) do{}while(0) 554 #endif 555 556 #define ERR(stuff...) pr_err("udc: " stuff) 557 #define WARNING(stuff...) pr_warn("udc: " stuff) 558 #define INFO(stuff...) pr_info("udc: " stuff) 559 560 /*-------------------------------------------------------------------------*/ 561 562 /* ### Add board specific defines here 563 */ 564 565 /* 566 * ### pipe direction macro from device view 567 */ 568 #define USB_RECV 0 /* OUT EP */ 569 #define USB_SEND 1 /* IN EP */ 570 571 /* 572 * ### internal used help routines. 573 */ 574 #define ep_index(EP) ((EP)->ep.desc->bEndpointAddress&0xF) 575 #define ep_maxpacket(EP) ((EP)->ep.maxpacket) 576 #define ep_is_in(EP) ( (ep_index(EP) == 0) ? (EP->udc->ep0_dir == \ 577 USB_DIR_IN) : ((EP)->ep.desc->bEndpointAddress \ 578 & USB_DIR_IN)==USB_DIR_IN) 579 #define get_ep_by_pipe(udc, pipe) ((pipe == 1)? &udc->eps[0]: \ 580 &udc->eps[pipe]) 581 #define get_pipe_by_windex(windex) ((windex & USB_ENDPOINT_NUMBER_MASK) \ 582 * 2 + ((windex & USB_DIR_IN) ? 1 : 0)) 583 #define get_pipe_by_ep(EP) (ep_index(EP) * 2 + ep_is_in(EP)) 584 585 static inline struct ep_queue_head *get_qh_by_ep(struct fsl_ep *ep) 586 { 587 /* we only have one ep0 structure but two queue heads */ 588 if (ep_index(ep) != 0) 589 return ep->qh; 590 else 591 return &ep->udc->ep_qh[(ep->udc->ep0_dir == 592 USB_DIR_IN) ? 1 : 0]; 593 } 594 595 struct platform_device; 596 #ifdef CONFIG_ARCH_MXC 597 int fsl_udc_clk_init(struct platform_device *pdev); 598 int fsl_udc_clk_finalize(struct platform_device *pdev); 599 void fsl_udc_clk_release(void); 600 #else 601 static inline int fsl_udc_clk_init(struct platform_device *pdev) 602 { 603 return 0; 604 } 605 static inline int fsl_udc_clk_finalize(struct platform_device *pdev) 606 { 607 return 0; 608 } 609 static inline void fsl_udc_clk_release(void) 610 { 611 } 612 #endif 613 614 #endif 615