1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * USB Glue for Amlogic G12A SoCs 4 * 5 * Copyright (c) 2019 BayLibre, SAS 6 * Author: Neil Armstrong <narmstrong@baylibre.com> 7 */ 8 9 /* 10 * The USB is organized with a glue around the DWC3 Controller IP as : 11 * - Control registers for each USB2 Ports 12 * - Control registers for the USB PHY layer 13 * - SuperSpeed PHY can be enabled only if port is used 14 * - Dynamic OTG switching with ID change interrupt 15 */ 16 17 #include <linux/module.h> 18 #include <linux/kernel.h> 19 #include <linux/platform_device.h> 20 #include <linux/clk.h> 21 #include <linux/of.h> 22 #include <linux/of_platform.h> 23 #include <linux/pm_runtime.h> 24 #include <linux/regmap.h> 25 #include <linux/bitfield.h> 26 #include <linux/bitops.h> 27 #include <linux/reset.h> 28 #include <linux/phy/phy.h> 29 #include <linux/usb/otg.h> 30 #include <linux/usb/role.h> 31 #include <linux/regulator/consumer.h> 32 33 /* USB2 Ports Control Registers, offsets are per-port */ 34 35 #define U2P_REG_SIZE 0x20 36 37 #define U2P_R0 0x0 38 #define U2P_R0_HOST_DEVICE BIT(0) 39 #define U2P_R0_POWER_OK BIT(1) 40 #define U2P_R0_HAST_MODE BIT(2) 41 #define U2P_R0_POWER_ON_RESET BIT(3) 42 #define U2P_R0_ID_PULLUP BIT(4) 43 #define U2P_R0_DRV_VBUS BIT(5) 44 45 #define U2P_R1 0x4 46 #define U2P_R1_PHY_READY BIT(0) 47 #define U2P_R1_ID_DIG BIT(1) 48 #define U2P_R1_OTG_SESSION_VALID BIT(2) 49 #define U2P_R1_VBUS_VALID BIT(3) 50 51 /* USB Glue Control Registers */ 52 53 #define G12A_GLUE_OFFSET 0x80 54 55 #define USB_R0 0x00 56 #define USB_R0_P30_LANE0_TX2RX_LOOPBACK BIT(17) 57 #define USB_R0_P30_LANE0_EXT_PCLK_REQ BIT(18) 58 #define USB_R0_P30_PCS_RX_LOS_MASK_VAL_MASK GENMASK(28, 19) 59 #define USB_R0_U2D_SS_SCALEDOWN_MODE_MASK GENMASK(30, 29) 60 #define USB_R0_U2D_ACT BIT(31) 61 62 #define USB_R1 0x04 63 #define USB_R1_U3H_BIGENDIAN_GS BIT(0) 64 #define USB_R1_U3H_PME_ENABLE BIT(1) 65 #define USB_R1_U3H_HUB_PORT_OVERCURRENT_MASK GENMASK(4, 2) 66 #define USB_R1_U3H_HUB_PORT_PERM_ATTACH_MASK GENMASK(9, 7) 67 #define USB_R1_U3H_HOST_U2_PORT_DISABLE_MASK GENMASK(13, 12) 68 #define USB_R1_U3H_HOST_U3_PORT_DISABLE BIT(16) 69 #define USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT BIT(17) 70 #define USB_R1_U3H_HOST_MSI_ENABLE BIT(18) 71 #define USB_R1_U3H_FLADJ_30MHZ_REG_MASK GENMASK(24, 19) 72 #define USB_R1_P30_PCS_TX_SWING_FULL_MASK GENMASK(31, 25) 73 74 #define USB_R2 0x08 75 #define USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK GENMASK(25, 20) 76 #define USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK GENMASK(31, 26) 77 78 #define USB_R3 0x0c 79 #define USB_R3_P30_SSC_ENABLE BIT(0) 80 #define USB_R3_P30_SSC_RANGE_MASK GENMASK(3, 1) 81 #define USB_R3_P30_SSC_REF_CLK_SEL_MASK GENMASK(12, 4) 82 #define USB_R3_P30_REF_SSP_EN BIT(13) 83 84 #define USB_R4 0x10 85 #define USB_R4_P21_PORT_RESET_0 BIT(0) 86 #define USB_R4_P21_SLEEP_M0 BIT(1) 87 #define USB_R4_MEM_PD_MASK GENMASK(3, 2) 88 #define USB_R4_P21_ONLY BIT(4) 89 90 #define USB_R5 0x14 91 #define USB_R5_ID_DIG_SYNC BIT(0) 92 #define USB_R5_ID_DIG_REG BIT(1) 93 #define USB_R5_ID_DIG_CFG_MASK GENMASK(3, 2) 94 #define USB_R5_ID_DIG_EN_0 BIT(4) 95 #define USB_R5_ID_DIG_EN_1 BIT(5) 96 #define USB_R5_ID_DIG_CURR BIT(6) 97 #define USB_R5_ID_DIG_IRQ BIT(7) 98 #define USB_R5_ID_DIG_TH_MASK GENMASK(15, 8) 99 #define USB_R5_ID_DIG_CNT_MASK GENMASK(23, 16) 100 101 #define PHY_COUNT 3 102 #define USB2_OTG_PHY 1 103 104 static struct clk_bulk_data meson_gxl_clocks[] = { 105 { .id = "usb_ctrl" }, 106 { .id = "ddr" }, 107 }; 108 109 static struct clk_bulk_data meson_g12a_clocks[] = { 110 { .id = NULL }, 111 }; 112 113 static struct clk_bulk_data meson_a1_clocks[] = { 114 { .id = "usb_ctrl" }, 115 { .id = "usb_bus" }, 116 { .id = "xtal_usb_ctrl" }, 117 }; 118 119 static const char * const meson_gxm_phy_names[] = { 120 "usb2-phy0", "usb2-phy1", "usb2-phy2", 121 }; 122 123 static const char * const meson_g12a_phy_names[] = { 124 "usb2-phy0", "usb2-phy1", "usb3-phy0", 125 }; 126 127 /* 128 * Amlogic A1 has a single physical PHY, in slot 1, but still has the 129 * two U2 PHY controls register blocks like G12A. 130 * AXG has the similar scheme, thus needs the same tweak. 131 * Handling the first PHY on slot 1 would need a large amount of code 132 * changes, and the current management is generic enough to handle it 133 * correctly when only the "usb2-phy1" phy is specified on-par with the 134 * DT bindings. 135 */ 136 static const char * const meson_a1_phy_names[] = { 137 "usb2-phy0", "usb2-phy1" 138 }; 139 140 struct dwc3_meson_g12a; 141 142 struct dwc3_meson_g12a_drvdata { 143 bool otg_phy_host_port_disable; 144 struct clk_bulk_data *clks; 145 int num_clks; 146 const char * const *phy_names; 147 int num_phys; 148 int (*setup_regmaps)(struct dwc3_meson_g12a *priv, void __iomem *base); 149 int (*usb2_init_phy)(struct dwc3_meson_g12a *priv, int i, 150 enum phy_mode mode); 151 int (*set_phy_mode)(struct dwc3_meson_g12a *priv, int i, 152 enum phy_mode mode); 153 int (*usb_init)(struct dwc3_meson_g12a *priv); 154 int (*usb_post_init)(struct dwc3_meson_g12a *priv); 155 }; 156 157 static int dwc3_meson_gxl_setup_regmaps(struct dwc3_meson_g12a *priv, 158 void __iomem *base); 159 static int dwc3_meson_g12a_setup_regmaps(struct dwc3_meson_g12a *priv, 160 void __iomem *base); 161 162 static int dwc3_meson_g12a_usb2_init_phy(struct dwc3_meson_g12a *priv, int i, 163 enum phy_mode mode); 164 static int dwc3_meson_gxl_usb2_init_phy(struct dwc3_meson_g12a *priv, int i, 165 enum phy_mode mode); 166 167 static int dwc3_meson_g12a_set_phy_mode(struct dwc3_meson_g12a *priv, 168 int i, enum phy_mode mode); 169 static int dwc3_meson_gxl_set_phy_mode(struct dwc3_meson_g12a *priv, 170 int i, enum phy_mode mode); 171 172 static int dwc3_meson_g12a_usb_init(struct dwc3_meson_g12a *priv); 173 static int dwc3_meson_gxl_usb_init(struct dwc3_meson_g12a *priv); 174 175 static int dwc3_meson_gxl_usb_post_init(struct dwc3_meson_g12a *priv); 176 177 /* 178 * For GXL and GXM SoCs: 179 * USB Phy muxing between the DWC2 Device controller and the DWC3 Host 180 * controller is buggy when switching from Device to Host when USB port 181 * is unpopulated, it causes the DWC3 to hard crash. 182 * When populated (including OTG switching with ID pin), the switch works 183 * like a charm like on the G12A platforms. 184 * In order to still switch from Host to Device on an USB Type-A port, 185 * an U2_PORT_DISABLE bit has been added to disconnect the DWC3 Host 186 * controller from the port, but when used the DWC3 controller must be 187 * reset to recover usage of the port. 188 */ 189 190 static const struct dwc3_meson_g12a_drvdata gxl_drvdata = { 191 .otg_phy_host_port_disable = true, 192 .clks = meson_gxl_clocks, 193 .num_clks = ARRAY_SIZE(meson_g12a_clocks), 194 .phy_names = meson_a1_phy_names, 195 .num_phys = ARRAY_SIZE(meson_a1_phy_names), 196 .setup_regmaps = dwc3_meson_gxl_setup_regmaps, 197 .usb2_init_phy = dwc3_meson_gxl_usb2_init_phy, 198 .set_phy_mode = dwc3_meson_gxl_set_phy_mode, 199 .usb_init = dwc3_meson_gxl_usb_init, 200 .usb_post_init = dwc3_meson_gxl_usb_post_init, 201 }; 202 203 static const struct dwc3_meson_g12a_drvdata gxm_drvdata = { 204 .otg_phy_host_port_disable = true, 205 .clks = meson_gxl_clocks, 206 .num_clks = ARRAY_SIZE(meson_g12a_clocks), 207 .phy_names = meson_gxm_phy_names, 208 .num_phys = ARRAY_SIZE(meson_gxm_phy_names), 209 .setup_regmaps = dwc3_meson_gxl_setup_regmaps, 210 .usb2_init_phy = dwc3_meson_gxl_usb2_init_phy, 211 .set_phy_mode = dwc3_meson_gxl_set_phy_mode, 212 .usb_init = dwc3_meson_gxl_usb_init, 213 .usb_post_init = dwc3_meson_gxl_usb_post_init, 214 }; 215 216 static const struct dwc3_meson_g12a_drvdata axg_drvdata = { 217 .clks = meson_gxl_clocks, 218 .num_clks = ARRAY_SIZE(meson_gxl_clocks), 219 .phy_names = meson_a1_phy_names, 220 .num_phys = ARRAY_SIZE(meson_a1_phy_names), 221 .setup_regmaps = dwc3_meson_gxl_setup_regmaps, 222 .usb2_init_phy = dwc3_meson_gxl_usb2_init_phy, 223 .set_phy_mode = dwc3_meson_gxl_set_phy_mode, 224 .usb_init = dwc3_meson_g12a_usb_init, 225 .usb_post_init = dwc3_meson_gxl_usb_post_init, 226 }; 227 228 static const struct dwc3_meson_g12a_drvdata g12a_drvdata = { 229 .clks = meson_g12a_clocks, 230 .num_clks = ARRAY_SIZE(meson_g12a_clocks), 231 .phy_names = meson_g12a_phy_names, 232 .num_phys = ARRAY_SIZE(meson_g12a_phy_names), 233 .setup_regmaps = dwc3_meson_g12a_setup_regmaps, 234 .usb2_init_phy = dwc3_meson_g12a_usb2_init_phy, 235 .set_phy_mode = dwc3_meson_g12a_set_phy_mode, 236 .usb_init = dwc3_meson_g12a_usb_init, 237 }; 238 239 static const struct dwc3_meson_g12a_drvdata a1_drvdata = { 240 .clks = meson_a1_clocks, 241 .num_clks = ARRAY_SIZE(meson_a1_clocks), 242 .phy_names = meson_a1_phy_names, 243 .num_phys = ARRAY_SIZE(meson_a1_phy_names), 244 .setup_regmaps = dwc3_meson_g12a_setup_regmaps, 245 .usb2_init_phy = dwc3_meson_g12a_usb2_init_phy, 246 .set_phy_mode = dwc3_meson_g12a_set_phy_mode, 247 .usb_init = dwc3_meson_g12a_usb_init, 248 }; 249 250 struct dwc3_meson_g12a { 251 struct device *dev; 252 struct regmap *u2p_regmap[PHY_COUNT]; 253 struct regmap *usb_glue_regmap; 254 struct reset_control *reset; 255 struct phy *phys[PHY_COUNT]; 256 enum usb_dr_mode otg_mode; 257 enum phy_mode otg_phy_mode; 258 unsigned int usb2_ports; 259 unsigned int usb3_ports; 260 struct regulator *vbus; 261 struct usb_role_switch_desc switch_desc; 262 struct usb_role_switch *role_switch; 263 const struct dwc3_meson_g12a_drvdata *drvdata; 264 }; 265 266 static int dwc3_meson_gxl_set_phy_mode(struct dwc3_meson_g12a *priv, 267 int i, enum phy_mode mode) 268 { 269 return phy_set_mode(priv->phys[i], mode); 270 } 271 272 static int dwc3_meson_gxl_usb2_init_phy(struct dwc3_meson_g12a *priv, int i, 273 enum phy_mode mode) 274 { 275 /* On GXL PHY must be started in device mode for DWC2 init */ 276 return priv->drvdata->set_phy_mode(priv, i, 277 (i == USB2_OTG_PHY) ? PHY_MODE_USB_DEVICE 278 : PHY_MODE_USB_HOST); 279 } 280 281 static int dwc3_meson_g12a_set_phy_mode(struct dwc3_meson_g12a *priv, 282 int i, enum phy_mode mode) 283 { 284 if (mode == PHY_MODE_USB_HOST) 285 regmap_update_bits(priv->u2p_regmap[i], U2P_R0, 286 U2P_R0_HOST_DEVICE, 287 U2P_R0_HOST_DEVICE); 288 else 289 regmap_update_bits(priv->u2p_regmap[i], U2P_R0, 290 U2P_R0_HOST_DEVICE, 0); 291 292 return 0; 293 } 294 295 static int dwc3_meson_g12a_usb2_init_phy(struct dwc3_meson_g12a *priv, int i, 296 enum phy_mode mode) 297 { 298 int ret; 299 300 regmap_update_bits(priv->u2p_regmap[i], U2P_R0, 301 U2P_R0_POWER_ON_RESET, 302 U2P_R0_POWER_ON_RESET); 303 304 if (i == USB2_OTG_PHY) { 305 regmap_update_bits(priv->u2p_regmap[i], U2P_R0, 306 U2P_R0_ID_PULLUP | U2P_R0_DRV_VBUS, 307 U2P_R0_ID_PULLUP | U2P_R0_DRV_VBUS); 308 309 ret = priv->drvdata->set_phy_mode(priv, i, mode); 310 } else 311 ret = priv->drvdata->set_phy_mode(priv, i, 312 PHY_MODE_USB_HOST); 313 314 if (ret) 315 return ret; 316 317 regmap_update_bits(priv->u2p_regmap[i], U2P_R0, 318 U2P_R0_POWER_ON_RESET, 0); 319 320 return 0; 321 } 322 323 static int dwc3_meson_g12a_usb2_init(struct dwc3_meson_g12a *priv, 324 enum phy_mode mode) 325 { 326 int i, ret; 327 328 for (i = 0; i < priv->drvdata->num_phys; ++i) { 329 if (!priv->phys[i]) 330 continue; 331 332 if (!strstr(priv->drvdata->phy_names[i], "usb2")) 333 continue; 334 335 ret = priv->drvdata->usb2_init_phy(priv, i, mode); 336 if (ret) 337 return ret; 338 } 339 340 return 0; 341 } 342 343 static void dwc3_meson_g12a_usb3_init(struct dwc3_meson_g12a *priv) 344 { 345 regmap_update_bits(priv->usb_glue_regmap, USB_R3, 346 USB_R3_P30_SSC_RANGE_MASK | 347 USB_R3_P30_REF_SSP_EN, 348 USB_R3_P30_SSC_ENABLE | 349 FIELD_PREP(USB_R3_P30_SSC_RANGE_MASK, 2) | 350 USB_R3_P30_REF_SSP_EN); 351 udelay(2); 352 353 regmap_update_bits(priv->usb_glue_regmap, USB_R2, 354 USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK, 355 FIELD_PREP(USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK, 0x15)); 356 357 regmap_update_bits(priv->usb_glue_regmap, USB_R2, 358 USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK, 359 FIELD_PREP(USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK, 0x20)); 360 361 udelay(2); 362 363 regmap_update_bits(priv->usb_glue_regmap, USB_R1, 364 USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT, 365 USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT); 366 367 regmap_update_bits(priv->usb_glue_regmap, USB_R1, 368 USB_R1_P30_PCS_TX_SWING_FULL_MASK, 369 FIELD_PREP(USB_R1_P30_PCS_TX_SWING_FULL_MASK, 127)); 370 } 371 372 static void dwc3_meson_g12a_usb_otg_apply_mode(struct dwc3_meson_g12a *priv, 373 enum phy_mode mode) 374 { 375 if (mode == PHY_MODE_USB_DEVICE) { 376 if (priv->otg_mode != USB_DR_MODE_OTG && 377 priv->drvdata->otg_phy_host_port_disable) 378 /* Isolate the OTG PHY port from the Host Controller */ 379 regmap_update_bits(priv->usb_glue_regmap, USB_R1, 380 USB_R1_U3H_HOST_U2_PORT_DISABLE_MASK, 381 FIELD_PREP(USB_R1_U3H_HOST_U2_PORT_DISABLE_MASK, 382 BIT(USB2_OTG_PHY))); 383 384 regmap_update_bits(priv->usb_glue_regmap, USB_R0, 385 USB_R0_U2D_ACT, USB_R0_U2D_ACT); 386 regmap_update_bits(priv->usb_glue_regmap, USB_R0, 387 USB_R0_U2D_SS_SCALEDOWN_MODE_MASK, 0); 388 regmap_update_bits(priv->usb_glue_regmap, USB_R4, 389 USB_R4_P21_SLEEP_M0, USB_R4_P21_SLEEP_M0); 390 } else { 391 if (priv->otg_mode != USB_DR_MODE_OTG && 392 priv->drvdata->otg_phy_host_port_disable) { 393 regmap_update_bits(priv->usb_glue_regmap, USB_R1, 394 USB_R1_U3H_HOST_U2_PORT_DISABLE_MASK, 0); 395 msleep(500); 396 } 397 regmap_update_bits(priv->usb_glue_regmap, USB_R0, 398 USB_R0_U2D_ACT, 0); 399 regmap_update_bits(priv->usb_glue_regmap, USB_R4, 400 USB_R4_P21_SLEEP_M0, 0); 401 } 402 } 403 404 static int dwc3_meson_g12a_usb_init_glue(struct dwc3_meson_g12a *priv, 405 enum phy_mode mode) 406 { 407 int ret; 408 409 ret = dwc3_meson_g12a_usb2_init(priv, mode); 410 if (ret) 411 return ret; 412 413 regmap_update_bits(priv->usb_glue_regmap, USB_R1, 414 USB_R1_U3H_FLADJ_30MHZ_REG_MASK, 415 FIELD_PREP(USB_R1_U3H_FLADJ_30MHZ_REG_MASK, 0x20)); 416 417 regmap_update_bits(priv->usb_glue_regmap, USB_R5, 418 USB_R5_ID_DIG_EN_0, 419 USB_R5_ID_DIG_EN_0); 420 regmap_update_bits(priv->usb_glue_regmap, USB_R5, 421 USB_R5_ID_DIG_EN_1, 422 USB_R5_ID_DIG_EN_1); 423 regmap_update_bits(priv->usb_glue_regmap, USB_R5, 424 USB_R5_ID_DIG_TH_MASK, 425 FIELD_PREP(USB_R5_ID_DIG_TH_MASK, 0xff)); 426 427 /* If we have an actual SuperSpeed port, initialize it */ 428 if (priv->usb3_ports) 429 dwc3_meson_g12a_usb3_init(priv); 430 431 dwc3_meson_g12a_usb_otg_apply_mode(priv, mode); 432 433 return 0; 434 } 435 436 static const struct regmap_config phy_meson_g12a_usb_glue_regmap_conf = { 437 .name = "usb-glue", 438 .reg_bits = 8, 439 .val_bits = 32, 440 .reg_stride = 4, 441 .max_register = USB_R5, 442 }; 443 444 static int dwc3_meson_g12a_get_phys(struct dwc3_meson_g12a *priv) 445 { 446 const char *phy_name; 447 int i; 448 449 for (i = 0 ; i < priv->drvdata->num_phys ; ++i) { 450 phy_name = priv->drvdata->phy_names[i]; 451 priv->phys[i] = devm_phy_optional_get(priv->dev, phy_name); 452 if (!priv->phys[i]) 453 continue; 454 455 if (IS_ERR(priv->phys[i])) 456 return PTR_ERR(priv->phys[i]); 457 458 if (strstr(phy_name, "usb3")) 459 priv->usb3_ports++; 460 else 461 priv->usb2_ports++; 462 } 463 464 dev_info(priv->dev, "USB2 ports: %d\n", priv->usb2_ports); 465 dev_info(priv->dev, "USB3 ports: %d\n", priv->usb3_ports); 466 467 return 0; 468 } 469 470 static enum phy_mode dwc3_meson_g12a_get_id(struct dwc3_meson_g12a *priv) 471 { 472 u32 reg; 473 474 regmap_read(priv->usb_glue_regmap, USB_R5, ®); 475 476 if (reg & (USB_R5_ID_DIG_SYNC | USB_R5_ID_DIG_REG)) 477 return PHY_MODE_USB_DEVICE; 478 479 return PHY_MODE_USB_HOST; 480 } 481 482 static int dwc3_meson_g12a_otg_mode_set(struct dwc3_meson_g12a *priv, 483 enum phy_mode mode) 484 { 485 int ret; 486 487 if (!priv->phys[USB2_OTG_PHY]) 488 return -EINVAL; 489 490 if (mode == PHY_MODE_USB_HOST) 491 dev_info(priv->dev, "switching to Host Mode\n"); 492 else 493 dev_info(priv->dev, "switching to Device Mode\n"); 494 495 if (priv->vbus) { 496 if (mode == PHY_MODE_USB_DEVICE) 497 ret = regulator_disable(priv->vbus); 498 else 499 ret = regulator_enable(priv->vbus); 500 if (ret) 501 return ret; 502 } 503 504 priv->otg_phy_mode = mode; 505 506 ret = priv->drvdata->set_phy_mode(priv, USB2_OTG_PHY, mode); 507 if (ret) 508 return ret; 509 510 dwc3_meson_g12a_usb_otg_apply_mode(priv, mode); 511 512 return 0; 513 } 514 515 static int dwc3_meson_g12a_role_set(struct usb_role_switch *sw, 516 enum usb_role role) 517 { 518 struct dwc3_meson_g12a *priv = usb_role_switch_get_drvdata(sw); 519 enum phy_mode mode; 520 521 if (role == USB_ROLE_NONE) 522 return 0; 523 524 mode = (role == USB_ROLE_HOST) ? PHY_MODE_USB_HOST 525 : PHY_MODE_USB_DEVICE; 526 527 if (mode == priv->otg_phy_mode) 528 return 0; 529 530 if (priv->drvdata->otg_phy_host_port_disable) 531 dev_warn_once(priv->dev, "Broken manual OTG switch\n"); 532 533 return dwc3_meson_g12a_otg_mode_set(priv, mode); 534 } 535 536 static enum usb_role dwc3_meson_g12a_role_get(struct usb_role_switch *sw) 537 { 538 struct dwc3_meson_g12a *priv = usb_role_switch_get_drvdata(sw); 539 540 return priv->otg_phy_mode == PHY_MODE_USB_HOST ? 541 USB_ROLE_HOST : USB_ROLE_DEVICE; 542 } 543 544 static irqreturn_t dwc3_meson_g12a_irq_thread(int irq, void *data) 545 { 546 struct dwc3_meson_g12a *priv = data; 547 enum phy_mode otg_id; 548 549 otg_id = dwc3_meson_g12a_get_id(priv); 550 if (otg_id != priv->otg_phy_mode) { 551 if (dwc3_meson_g12a_otg_mode_set(priv, otg_id)) 552 dev_warn(priv->dev, "Failed to switch OTG mode\n"); 553 } 554 555 regmap_update_bits(priv->usb_glue_regmap, USB_R5, 556 USB_R5_ID_DIG_IRQ, 0); 557 558 return IRQ_HANDLED; 559 } 560 561 static struct device *dwc3_meson_g12_find_child(struct device *dev, 562 const char *compatible) 563 { 564 struct platform_device *pdev; 565 struct device_node *np; 566 567 np = of_get_compatible_child(dev->of_node, compatible); 568 if (!np) 569 return NULL; 570 571 pdev = of_find_device_by_node(np); 572 of_node_put(np); 573 if (!pdev) 574 return NULL; 575 576 return &pdev->dev; 577 } 578 579 static int dwc3_meson_g12a_otg_init(struct platform_device *pdev, 580 struct dwc3_meson_g12a *priv) 581 { 582 enum phy_mode otg_id; 583 int ret, irq; 584 struct device *dev = &pdev->dev; 585 586 if (priv->otg_mode == USB_DR_MODE_OTG) { 587 /* Ack irq before registering */ 588 regmap_update_bits(priv->usb_glue_regmap, USB_R5, 589 USB_R5_ID_DIG_IRQ, 0); 590 591 irq = platform_get_irq(pdev, 0); 592 if (irq < 0) 593 return irq; 594 ret = devm_request_threaded_irq(&pdev->dev, irq, NULL, 595 dwc3_meson_g12a_irq_thread, 596 IRQF_ONESHOT, pdev->name, priv); 597 if (ret) 598 return ret; 599 } 600 601 /* Setup OTG mode corresponding to the ID pin */ 602 if (priv->otg_mode == USB_DR_MODE_OTG) { 603 otg_id = dwc3_meson_g12a_get_id(priv); 604 if (otg_id != priv->otg_phy_mode) { 605 if (dwc3_meson_g12a_otg_mode_set(priv, otg_id)) 606 dev_warn(dev, "Failed to switch OTG mode\n"); 607 } 608 } 609 610 /* Setup role switcher */ 611 priv->switch_desc.usb2_port = dwc3_meson_g12_find_child(dev, 612 "snps,dwc3"); 613 priv->switch_desc.udc = dwc3_meson_g12_find_child(dev, "snps,dwc2"); 614 priv->switch_desc.allow_userspace_control = true; 615 priv->switch_desc.set = dwc3_meson_g12a_role_set; 616 priv->switch_desc.get = dwc3_meson_g12a_role_get; 617 priv->switch_desc.driver_data = priv; 618 619 priv->role_switch = usb_role_switch_register(dev, &priv->switch_desc); 620 if (IS_ERR(priv->role_switch)) 621 dev_warn(dev, "Unable to register Role Switch\n"); 622 623 return 0; 624 } 625 626 static int dwc3_meson_gxl_setup_regmaps(struct dwc3_meson_g12a *priv, 627 void __iomem *base) 628 { 629 /* GXL controls the PHY mode in the PHY registers unlike G12A */ 630 priv->usb_glue_regmap = devm_regmap_init_mmio(priv->dev, base, 631 &phy_meson_g12a_usb_glue_regmap_conf); 632 return PTR_ERR_OR_ZERO(priv->usb_glue_regmap); 633 } 634 635 static int dwc3_meson_g12a_setup_regmaps(struct dwc3_meson_g12a *priv, 636 void __iomem *base) 637 { 638 int i; 639 640 priv->usb_glue_regmap = devm_regmap_init_mmio(priv->dev, 641 base + G12A_GLUE_OFFSET, 642 &phy_meson_g12a_usb_glue_regmap_conf); 643 if (IS_ERR(priv->usb_glue_regmap)) 644 return PTR_ERR(priv->usb_glue_regmap); 645 646 /* Create a regmap for each USB2 PHY control register set */ 647 for (i = 0; i < priv->drvdata->num_phys; i++) { 648 struct regmap_config u2p_regmap_config = { 649 .reg_bits = 8, 650 .val_bits = 32, 651 .reg_stride = 4, 652 .max_register = U2P_R1, 653 }; 654 655 if (!strstr(priv->drvdata->phy_names[i], "usb2")) 656 continue; 657 658 u2p_regmap_config.name = devm_kasprintf(priv->dev, GFP_KERNEL, 659 "u2p-%d", i); 660 if (!u2p_regmap_config.name) 661 return -ENOMEM; 662 663 priv->u2p_regmap[i] = devm_regmap_init_mmio(priv->dev, 664 base + (i * U2P_REG_SIZE), 665 &u2p_regmap_config); 666 if (IS_ERR(priv->u2p_regmap[i])) 667 return PTR_ERR(priv->u2p_regmap[i]); 668 } 669 670 return 0; 671 } 672 673 static int dwc3_meson_g12a_usb_init(struct dwc3_meson_g12a *priv) 674 { 675 return dwc3_meson_g12a_usb_init_glue(priv, priv->otg_phy_mode); 676 } 677 678 static int dwc3_meson_gxl_usb_init(struct dwc3_meson_g12a *priv) 679 { 680 return dwc3_meson_g12a_usb_init_glue(priv, PHY_MODE_USB_DEVICE); 681 } 682 683 static int dwc3_meson_gxl_usb_post_init(struct dwc3_meson_g12a *priv) 684 { 685 int ret; 686 687 ret = priv->drvdata->set_phy_mode(priv, USB2_OTG_PHY, 688 priv->otg_phy_mode); 689 if (ret) 690 return ret; 691 692 dwc3_meson_g12a_usb_otg_apply_mode(priv, priv->otg_phy_mode); 693 694 return 0; 695 } 696 697 static int dwc3_meson_g12a_probe(struct platform_device *pdev) 698 { 699 struct dwc3_meson_g12a *priv; 700 struct device *dev = &pdev->dev; 701 struct device_node *np = dev->of_node; 702 void __iomem *base; 703 int ret, i; 704 705 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); 706 if (!priv) 707 return -ENOMEM; 708 709 base = devm_platform_ioremap_resource(pdev, 0); 710 if (IS_ERR(base)) 711 return PTR_ERR(base); 712 713 priv->drvdata = of_device_get_match_data(&pdev->dev); 714 priv->dev = dev; 715 716 priv->vbus = devm_regulator_get_optional(dev, "vbus"); 717 if (IS_ERR(priv->vbus)) { 718 if (PTR_ERR(priv->vbus) == -EPROBE_DEFER) 719 return PTR_ERR(priv->vbus); 720 priv->vbus = NULL; 721 } 722 723 ret = devm_clk_bulk_get(dev, 724 priv->drvdata->num_clks, 725 priv->drvdata->clks); 726 if (ret) 727 return ret; 728 729 ret = clk_bulk_prepare_enable(priv->drvdata->num_clks, 730 priv->drvdata->clks); 731 if (ret) 732 return ret; 733 734 platform_set_drvdata(pdev, priv); 735 736 priv->reset = devm_reset_control_get_shared(dev, NULL); 737 if (IS_ERR(priv->reset)) { 738 ret = PTR_ERR(priv->reset); 739 dev_err(dev, "failed to get device reset, err=%d\n", ret); 740 goto err_disable_clks; 741 } 742 743 ret = reset_control_reset(priv->reset); 744 if (ret) 745 goto err_disable_clks; 746 747 ret = dwc3_meson_g12a_get_phys(priv); 748 if (ret) 749 goto err_rearm; 750 751 ret = priv->drvdata->setup_regmaps(priv, base); 752 if (ret) 753 goto err_rearm; 754 755 if (priv->vbus) { 756 ret = regulator_enable(priv->vbus); 757 if (ret) 758 goto err_rearm; 759 } 760 761 /* Get dr_mode */ 762 priv->otg_mode = usb_get_dr_mode(dev); 763 764 if (priv->otg_mode == USB_DR_MODE_PERIPHERAL) 765 priv->otg_phy_mode = PHY_MODE_USB_DEVICE; 766 else 767 priv->otg_phy_mode = PHY_MODE_USB_HOST; 768 769 ret = priv->drvdata->usb_init(priv); 770 if (ret) 771 goto err_disable_regulator; 772 773 /* Init PHYs */ 774 for (i = 0 ; i < PHY_COUNT ; ++i) { 775 ret = phy_init(priv->phys[i]); 776 if (ret) 777 goto err_disable_regulator; 778 } 779 780 /* Set PHY Power */ 781 for (i = 0 ; i < PHY_COUNT ; ++i) { 782 ret = phy_power_on(priv->phys[i]); 783 if (ret) 784 goto err_phys_exit; 785 } 786 787 if (priv->drvdata->usb_post_init) { 788 ret = priv->drvdata->usb_post_init(priv); 789 if (ret) 790 goto err_phys_power; 791 } 792 793 ret = of_platform_populate(np, NULL, NULL, dev); 794 if (ret) 795 goto err_phys_power; 796 797 ret = dwc3_meson_g12a_otg_init(pdev, priv); 798 if (ret) 799 goto err_plat_depopulate; 800 801 pm_runtime_set_active(dev); 802 pm_runtime_enable(dev); 803 pm_runtime_get_sync(dev); 804 805 return 0; 806 807 err_plat_depopulate: 808 of_platform_depopulate(dev); 809 810 err_phys_power: 811 for (i = 0 ; i < PHY_COUNT ; ++i) 812 phy_power_off(priv->phys[i]); 813 814 err_phys_exit: 815 for (i = 0 ; i < PHY_COUNT ; ++i) 816 phy_exit(priv->phys[i]); 817 818 err_disable_regulator: 819 if (priv->vbus) 820 regulator_disable(priv->vbus); 821 822 err_rearm: 823 reset_control_rearm(priv->reset); 824 825 err_disable_clks: 826 clk_bulk_disable_unprepare(priv->drvdata->num_clks, 827 priv->drvdata->clks); 828 829 return ret; 830 } 831 832 static void dwc3_meson_g12a_remove(struct platform_device *pdev) 833 { 834 struct dwc3_meson_g12a *priv = platform_get_drvdata(pdev); 835 struct device *dev = &pdev->dev; 836 int i; 837 838 usb_role_switch_unregister(priv->role_switch); 839 840 of_platform_depopulate(dev); 841 842 for (i = 0 ; i < PHY_COUNT ; ++i) { 843 phy_power_off(priv->phys[i]); 844 phy_exit(priv->phys[i]); 845 } 846 847 pm_runtime_disable(dev); 848 pm_runtime_put_noidle(dev); 849 pm_runtime_set_suspended(dev); 850 851 reset_control_rearm(priv->reset); 852 853 clk_bulk_disable_unprepare(priv->drvdata->num_clks, 854 priv->drvdata->clks); 855 } 856 857 static int __maybe_unused dwc3_meson_g12a_runtime_suspend(struct device *dev) 858 { 859 struct dwc3_meson_g12a *priv = dev_get_drvdata(dev); 860 861 clk_bulk_disable_unprepare(priv->drvdata->num_clks, 862 priv->drvdata->clks); 863 864 return 0; 865 } 866 867 static int __maybe_unused dwc3_meson_g12a_runtime_resume(struct device *dev) 868 { 869 struct dwc3_meson_g12a *priv = dev_get_drvdata(dev); 870 871 return clk_bulk_prepare_enable(priv->drvdata->num_clks, 872 priv->drvdata->clks); 873 } 874 875 static int __maybe_unused dwc3_meson_g12a_suspend(struct device *dev) 876 { 877 struct dwc3_meson_g12a *priv = dev_get_drvdata(dev); 878 int i, ret; 879 880 if (priv->vbus && priv->otg_phy_mode == PHY_MODE_USB_HOST) { 881 ret = regulator_disable(priv->vbus); 882 if (ret) 883 return ret; 884 } 885 886 for (i = 0 ; i < PHY_COUNT ; ++i) { 887 phy_power_off(priv->phys[i]); 888 phy_exit(priv->phys[i]); 889 } 890 891 reset_control_rearm(priv->reset); 892 893 return 0; 894 } 895 896 static int __maybe_unused dwc3_meson_g12a_resume(struct device *dev) 897 { 898 struct dwc3_meson_g12a *priv = dev_get_drvdata(dev); 899 int i, ret; 900 901 ret = reset_control_reset(priv->reset); 902 if (ret) 903 return ret; 904 905 ret = priv->drvdata->usb_init(priv); 906 if (ret) 907 return ret; 908 909 /* Init PHYs */ 910 for (i = 0 ; i < PHY_COUNT ; ++i) { 911 ret = phy_init(priv->phys[i]); 912 if (ret) 913 return ret; 914 } 915 916 /* Set PHY Power */ 917 for (i = 0 ; i < PHY_COUNT ; ++i) { 918 ret = phy_power_on(priv->phys[i]); 919 if (ret) 920 return ret; 921 } 922 923 if (priv->vbus && priv->otg_phy_mode == PHY_MODE_USB_HOST) { 924 ret = regulator_enable(priv->vbus); 925 if (ret) 926 return ret; 927 } 928 929 if (priv->drvdata->usb_post_init) { 930 ret = priv->drvdata->usb_post_init(priv); 931 if (ret) 932 return ret; 933 } 934 935 return 0; 936 } 937 938 static const struct dev_pm_ops dwc3_meson_g12a_dev_pm_ops = { 939 SET_SYSTEM_SLEEP_PM_OPS(dwc3_meson_g12a_suspend, dwc3_meson_g12a_resume) 940 SET_RUNTIME_PM_OPS(dwc3_meson_g12a_runtime_suspend, 941 dwc3_meson_g12a_runtime_resume, NULL) 942 }; 943 944 static const struct of_device_id dwc3_meson_g12a_match[] = { 945 { 946 .compatible = "amlogic,meson-gxl-usb-ctrl", 947 .data = &gxl_drvdata, 948 }, 949 { 950 .compatible = "amlogic,meson-gxm-usb-ctrl", 951 .data = &gxm_drvdata, 952 }, 953 { 954 .compatible = "amlogic,meson-axg-usb-ctrl", 955 .data = &axg_drvdata, 956 }, 957 { 958 .compatible = "amlogic,meson-g12a-usb-ctrl", 959 .data = &g12a_drvdata, 960 }, 961 { 962 .compatible = "amlogic,meson-a1-usb-ctrl", 963 .data = &a1_drvdata, 964 }, 965 { /* Sentinel */ } 966 }; 967 MODULE_DEVICE_TABLE(of, dwc3_meson_g12a_match); 968 969 static struct platform_driver dwc3_meson_g12a_driver = { 970 .probe = dwc3_meson_g12a_probe, 971 .remove = dwc3_meson_g12a_remove, 972 .driver = { 973 .name = "dwc3-meson-g12a", 974 .of_match_table = dwc3_meson_g12a_match, 975 .pm = &dwc3_meson_g12a_dev_pm_ops, 976 }, 977 }; 978 979 module_platform_driver(dwc3_meson_g12a_driver); 980 MODULE_LICENSE("GPL v2"); 981 MODULE_DESCRIPTION("Amlogic Meson G12A USB Glue Layer"); 982 MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); 983