1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * USB Glue for Amlogic G12A SoCs 4 * 5 * Copyright (c) 2019 BayLibre, SAS 6 * Author: Neil Armstrong <narmstrong@baylibre.com> 7 */ 8 9 /* 10 * The USB is organized with a glue around the DWC3 Controller IP as : 11 * - Control registers for each USB2 Ports 12 * - Control registers for the USB PHY layer 13 * - SuperSpeed PHY can be enabled only if port is used 14 * - Dynamic OTG switching with ID change interrupt 15 */ 16 17 #include <linux/module.h> 18 #include <linux/kernel.h> 19 #include <linux/platform_device.h> 20 #include <linux/clk.h> 21 #include <linux/of.h> 22 #include <linux/of_platform.h> 23 #include <linux/pm_runtime.h> 24 #include <linux/regmap.h> 25 #include <linux/bitfield.h> 26 #include <linux/bitops.h> 27 #include <linux/reset.h> 28 #include <linux/phy/phy.h> 29 #include <linux/usb/otg.h> 30 #include <linux/usb/role.h> 31 #include <linux/regulator/consumer.h> 32 33 /* USB2 Ports Control Registers, offsets are per-port */ 34 35 #define U2P_REG_SIZE 0x20 36 37 #define U2P_R0 0x0 38 #define U2P_R0_HOST_DEVICE BIT(0) 39 #define U2P_R0_POWER_OK BIT(1) 40 #define U2P_R0_HAST_MODE BIT(2) 41 #define U2P_R0_POWER_ON_RESET BIT(3) 42 #define U2P_R0_ID_PULLUP BIT(4) 43 #define U2P_R0_DRV_VBUS BIT(5) 44 45 #define U2P_R1 0x4 46 #define U2P_R1_PHY_READY BIT(0) 47 #define U2P_R1_ID_DIG BIT(1) 48 #define U2P_R1_OTG_SESSION_VALID BIT(2) 49 #define U2P_R1_VBUS_VALID BIT(3) 50 51 /* USB Glue Control Registers */ 52 53 #define G12A_GLUE_OFFSET 0x80 54 55 #define USB_R0 0x00 56 #define USB_R0_P30_LANE0_TX2RX_LOOPBACK BIT(17) 57 #define USB_R0_P30_LANE0_EXT_PCLK_REQ BIT(18) 58 #define USB_R0_P30_PCS_RX_LOS_MASK_VAL_MASK GENMASK(28, 19) 59 #define USB_R0_U2D_SS_SCALEDOWN_MODE_MASK GENMASK(30, 29) 60 #define USB_R0_U2D_ACT BIT(31) 61 62 #define USB_R1 0x04 63 #define USB_R1_U3H_BIGENDIAN_GS BIT(0) 64 #define USB_R1_U3H_PME_ENABLE BIT(1) 65 #define USB_R1_U3H_HUB_PORT_OVERCURRENT_MASK GENMASK(4, 2) 66 #define USB_R1_U3H_HUB_PORT_PERM_ATTACH_MASK GENMASK(9, 7) 67 #define USB_R1_U3H_HOST_U2_PORT_DISABLE_MASK GENMASK(13, 12) 68 #define USB_R1_U3H_HOST_U3_PORT_DISABLE BIT(16) 69 #define USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT BIT(17) 70 #define USB_R1_U3H_HOST_MSI_ENABLE BIT(18) 71 #define USB_R1_U3H_FLADJ_30MHZ_REG_MASK GENMASK(24, 19) 72 #define USB_R1_P30_PCS_TX_SWING_FULL_MASK GENMASK(31, 25) 73 74 #define USB_R2 0x08 75 #define USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK GENMASK(25, 20) 76 #define USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK GENMASK(31, 26) 77 78 #define USB_R3 0x0c 79 #define USB_R3_P30_SSC_ENABLE BIT(0) 80 #define USB_R3_P30_SSC_RANGE_MASK GENMASK(3, 1) 81 #define USB_R3_P30_SSC_REF_CLK_SEL_MASK GENMASK(12, 4) 82 #define USB_R3_P30_REF_SSP_EN BIT(13) 83 84 #define USB_R4 0x10 85 #define USB_R4_P21_PORT_RESET_0 BIT(0) 86 #define USB_R4_P21_SLEEP_M0 BIT(1) 87 #define USB_R4_MEM_PD_MASK GENMASK(3, 2) 88 #define USB_R4_P21_ONLY BIT(4) 89 90 #define USB_R5 0x14 91 #define USB_R5_ID_DIG_SYNC BIT(0) 92 #define USB_R5_ID_DIG_REG BIT(1) 93 #define USB_R5_ID_DIG_CFG_MASK GENMASK(3, 2) 94 #define USB_R5_ID_DIG_EN_0 BIT(4) 95 #define USB_R5_ID_DIG_EN_1 BIT(5) 96 #define USB_R5_ID_DIG_CURR BIT(6) 97 #define USB_R5_ID_DIG_IRQ BIT(7) 98 #define USB_R5_ID_DIG_TH_MASK GENMASK(15, 8) 99 #define USB_R5_ID_DIG_CNT_MASK GENMASK(23, 16) 100 101 #define PHY_COUNT 3 102 #define USB2_OTG_PHY 1 103 104 static struct clk_bulk_data meson_gxl_clocks[] = { 105 { .id = "usb_ctrl" }, 106 { .id = "ddr" }, 107 }; 108 109 static struct clk_bulk_data meson_g12a_clocks[] = { 110 { .id = NULL }, 111 }; 112 113 static struct clk_bulk_data meson_a1_clocks[] = { 114 { .id = "usb_ctrl" }, 115 { .id = "usb_bus" }, 116 { .id = "xtal_usb_ctrl" }, 117 }; 118 119 static const char * const meson_gxm_phy_names[] = { 120 "usb2-phy0", "usb2-phy1", "usb2-phy2", 121 }; 122 123 static const char * const meson_g12a_phy_names[] = { 124 "usb2-phy0", "usb2-phy1", "usb3-phy0", 125 }; 126 127 /* 128 * Amlogic A1 has a single physical PHY, in slot 1, but still has the 129 * two U2 PHY controls register blocks like G12A. 130 * AXG has the similar scheme, thus needs the same tweak. 131 * Handling the first PHY on slot 1 would need a large amount of code 132 * changes, and the current management is generic enough to handle it 133 * correctly when only the "usb2-phy1" phy is specified on-par with the 134 * DT bindings. 135 */ 136 static const char * const meson_a1_phy_names[] = { 137 "usb2-phy0", "usb2-phy1" 138 }; 139 140 struct dwc3_meson_g12a; 141 142 struct dwc3_meson_g12a_drvdata { 143 bool otg_switch_supported; 144 bool otg_phy_host_port_disable; 145 struct clk_bulk_data *clks; 146 int num_clks; 147 const char * const *phy_names; 148 int num_phys; 149 int (*setup_regmaps)(struct dwc3_meson_g12a *priv, void __iomem *base); 150 int (*usb2_init_phy)(struct dwc3_meson_g12a *priv, int i, 151 enum phy_mode mode); 152 int (*set_phy_mode)(struct dwc3_meson_g12a *priv, int i, 153 enum phy_mode mode); 154 int (*usb_init)(struct dwc3_meson_g12a *priv); 155 int (*usb_post_init)(struct dwc3_meson_g12a *priv); 156 }; 157 158 static int dwc3_meson_gxl_setup_regmaps(struct dwc3_meson_g12a *priv, 159 void __iomem *base); 160 static int dwc3_meson_g12a_setup_regmaps(struct dwc3_meson_g12a *priv, 161 void __iomem *base); 162 163 static int dwc3_meson_g12a_usb2_init_phy(struct dwc3_meson_g12a *priv, int i, 164 enum phy_mode mode); 165 static int dwc3_meson_gxl_usb2_init_phy(struct dwc3_meson_g12a *priv, int i, 166 enum phy_mode mode); 167 168 static int dwc3_meson_g12a_set_phy_mode(struct dwc3_meson_g12a *priv, 169 int i, enum phy_mode mode); 170 static int dwc3_meson_gxl_set_phy_mode(struct dwc3_meson_g12a *priv, 171 int i, enum phy_mode mode); 172 173 static int dwc3_meson_g12a_usb_init(struct dwc3_meson_g12a *priv); 174 static int dwc3_meson_gxl_usb_init(struct dwc3_meson_g12a *priv); 175 176 static int dwc3_meson_gxl_usb_post_init(struct dwc3_meson_g12a *priv); 177 178 /* 179 * For GXL and GXM SoCs: 180 * USB Phy muxing between the DWC2 Device controller and the DWC3 Host 181 * controller is buggy when switching from Device to Host when USB port 182 * is unpopulated, it causes the DWC3 to hard crash. 183 * When populated (including OTG switching with ID pin), the switch works 184 * like a charm like on the G12A platforms. 185 * In order to still switch from Host to Device on an USB Type-A port, 186 * an U2_PORT_DISABLE bit has been added to disconnect the DWC3 Host 187 * controller from the port, but when used the DWC3 controller must be 188 * reset to recover usage of the port. 189 */ 190 191 static const struct dwc3_meson_g12a_drvdata gxl_drvdata = { 192 .otg_switch_supported = true, 193 .otg_phy_host_port_disable = true, 194 .clks = meson_gxl_clocks, 195 .num_clks = ARRAY_SIZE(meson_g12a_clocks), 196 .phy_names = meson_a1_phy_names, 197 .num_phys = ARRAY_SIZE(meson_a1_phy_names), 198 .setup_regmaps = dwc3_meson_gxl_setup_regmaps, 199 .usb2_init_phy = dwc3_meson_gxl_usb2_init_phy, 200 .set_phy_mode = dwc3_meson_gxl_set_phy_mode, 201 .usb_init = dwc3_meson_gxl_usb_init, 202 .usb_post_init = dwc3_meson_gxl_usb_post_init, 203 }; 204 205 static const struct dwc3_meson_g12a_drvdata gxm_drvdata = { 206 .otg_switch_supported = true, 207 .otg_phy_host_port_disable = true, 208 .clks = meson_gxl_clocks, 209 .num_clks = ARRAY_SIZE(meson_g12a_clocks), 210 .phy_names = meson_gxm_phy_names, 211 .num_phys = ARRAY_SIZE(meson_gxm_phy_names), 212 .setup_regmaps = dwc3_meson_gxl_setup_regmaps, 213 .usb2_init_phy = dwc3_meson_gxl_usb2_init_phy, 214 .set_phy_mode = dwc3_meson_gxl_set_phy_mode, 215 .usb_init = dwc3_meson_gxl_usb_init, 216 .usb_post_init = dwc3_meson_gxl_usb_post_init, 217 }; 218 219 static const struct dwc3_meson_g12a_drvdata axg_drvdata = { 220 .otg_switch_supported = true, 221 .clks = meson_gxl_clocks, 222 .num_clks = ARRAY_SIZE(meson_gxl_clocks), 223 .phy_names = meson_a1_phy_names, 224 .num_phys = ARRAY_SIZE(meson_a1_phy_names), 225 .setup_regmaps = dwc3_meson_gxl_setup_regmaps, 226 .usb2_init_phy = dwc3_meson_gxl_usb2_init_phy, 227 .set_phy_mode = dwc3_meson_gxl_set_phy_mode, 228 .usb_init = dwc3_meson_g12a_usb_init, 229 .usb_post_init = dwc3_meson_gxl_usb_post_init, 230 }; 231 232 static const struct dwc3_meson_g12a_drvdata g12a_drvdata = { 233 .otg_switch_supported = true, 234 .clks = meson_g12a_clocks, 235 .num_clks = ARRAY_SIZE(meson_g12a_clocks), 236 .phy_names = meson_g12a_phy_names, 237 .num_phys = ARRAY_SIZE(meson_g12a_phy_names), 238 .setup_regmaps = dwc3_meson_g12a_setup_regmaps, 239 .usb2_init_phy = dwc3_meson_g12a_usb2_init_phy, 240 .set_phy_mode = dwc3_meson_g12a_set_phy_mode, 241 .usb_init = dwc3_meson_g12a_usb_init, 242 }; 243 244 static const struct dwc3_meson_g12a_drvdata a1_drvdata = { 245 .otg_switch_supported = false, 246 .clks = meson_a1_clocks, 247 .num_clks = ARRAY_SIZE(meson_a1_clocks), 248 .phy_names = meson_a1_phy_names, 249 .num_phys = ARRAY_SIZE(meson_a1_phy_names), 250 .setup_regmaps = dwc3_meson_g12a_setup_regmaps, 251 .usb2_init_phy = dwc3_meson_g12a_usb2_init_phy, 252 .set_phy_mode = dwc3_meson_g12a_set_phy_mode, 253 .usb_init = dwc3_meson_g12a_usb_init, 254 }; 255 256 struct dwc3_meson_g12a { 257 struct device *dev; 258 struct regmap *u2p_regmap[PHY_COUNT]; 259 struct regmap *usb_glue_regmap; 260 struct reset_control *reset; 261 struct phy *phys[PHY_COUNT]; 262 enum usb_dr_mode otg_mode; 263 enum phy_mode otg_phy_mode; 264 unsigned int usb2_ports; 265 unsigned int usb3_ports; 266 struct regulator *vbus; 267 struct usb_role_switch_desc switch_desc; 268 struct usb_role_switch *role_switch; 269 const struct dwc3_meson_g12a_drvdata *drvdata; 270 }; 271 272 static int dwc3_meson_gxl_set_phy_mode(struct dwc3_meson_g12a *priv, 273 int i, enum phy_mode mode) 274 { 275 return phy_set_mode(priv->phys[i], mode); 276 } 277 278 static int dwc3_meson_gxl_usb2_init_phy(struct dwc3_meson_g12a *priv, int i, 279 enum phy_mode mode) 280 { 281 /* On GXL PHY must be started in device mode for DWC2 init */ 282 return priv->drvdata->set_phy_mode(priv, i, 283 (i == USB2_OTG_PHY) ? PHY_MODE_USB_DEVICE 284 : PHY_MODE_USB_HOST); 285 } 286 287 static int dwc3_meson_g12a_set_phy_mode(struct dwc3_meson_g12a *priv, 288 int i, enum phy_mode mode) 289 { 290 if (mode == PHY_MODE_USB_HOST) 291 regmap_update_bits(priv->u2p_regmap[i], U2P_R0, 292 U2P_R0_HOST_DEVICE, 293 U2P_R0_HOST_DEVICE); 294 else 295 regmap_update_bits(priv->u2p_regmap[i], U2P_R0, 296 U2P_R0_HOST_DEVICE, 0); 297 298 return 0; 299 } 300 301 static int dwc3_meson_g12a_usb2_init_phy(struct dwc3_meson_g12a *priv, int i, 302 enum phy_mode mode) 303 { 304 int ret; 305 306 regmap_update_bits(priv->u2p_regmap[i], U2P_R0, 307 U2P_R0_POWER_ON_RESET, 308 U2P_R0_POWER_ON_RESET); 309 310 if (priv->drvdata->otg_switch_supported && i == USB2_OTG_PHY) { 311 regmap_update_bits(priv->u2p_regmap[i], U2P_R0, 312 U2P_R0_ID_PULLUP | U2P_R0_DRV_VBUS, 313 U2P_R0_ID_PULLUP | U2P_R0_DRV_VBUS); 314 315 ret = priv->drvdata->set_phy_mode(priv, i, mode); 316 } else 317 ret = priv->drvdata->set_phy_mode(priv, i, 318 PHY_MODE_USB_HOST); 319 320 if (ret) 321 return ret; 322 323 regmap_update_bits(priv->u2p_regmap[i], U2P_R0, 324 U2P_R0_POWER_ON_RESET, 0); 325 326 return 0; 327 } 328 329 static int dwc3_meson_g12a_usb2_init(struct dwc3_meson_g12a *priv, 330 enum phy_mode mode) 331 { 332 int i, ret; 333 334 for (i = 0; i < priv->drvdata->num_phys; ++i) { 335 if (!priv->phys[i]) 336 continue; 337 338 if (!strstr(priv->drvdata->phy_names[i], "usb2")) 339 continue; 340 341 ret = priv->drvdata->usb2_init_phy(priv, i, mode); 342 if (ret) 343 return ret; 344 } 345 346 return 0; 347 } 348 349 static void dwc3_meson_g12a_usb3_init(struct dwc3_meson_g12a *priv) 350 { 351 regmap_update_bits(priv->usb_glue_regmap, USB_R3, 352 USB_R3_P30_SSC_RANGE_MASK | 353 USB_R3_P30_REF_SSP_EN, 354 USB_R3_P30_SSC_ENABLE | 355 FIELD_PREP(USB_R3_P30_SSC_RANGE_MASK, 2) | 356 USB_R3_P30_REF_SSP_EN); 357 udelay(2); 358 359 regmap_update_bits(priv->usb_glue_regmap, USB_R2, 360 USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK, 361 FIELD_PREP(USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK, 0x15)); 362 363 regmap_update_bits(priv->usb_glue_regmap, USB_R2, 364 USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK, 365 FIELD_PREP(USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK, 0x20)); 366 367 udelay(2); 368 369 regmap_update_bits(priv->usb_glue_regmap, USB_R1, 370 USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT, 371 USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT); 372 373 regmap_update_bits(priv->usb_glue_regmap, USB_R1, 374 USB_R1_P30_PCS_TX_SWING_FULL_MASK, 375 FIELD_PREP(USB_R1_P30_PCS_TX_SWING_FULL_MASK, 127)); 376 } 377 378 static void dwc3_meson_g12a_usb_otg_apply_mode(struct dwc3_meson_g12a *priv, 379 enum phy_mode mode) 380 { 381 if (mode == PHY_MODE_USB_DEVICE) { 382 if (priv->otg_mode != USB_DR_MODE_OTG && 383 priv->drvdata->otg_phy_host_port_disable) 384 /* Isolate the OTG PHY port from the Host Controller */ 385 regmap_update_bits(priv->usb_glue_regmap, USB_R1, 386 USB_R1_U3H_HOST_U2_PORT_DISABLE_MASK, 387 FIELD_PREP(USB_R1_U3H_HOST_U2_PORT_DISABLE_MASK, 388 BIT(USB2_OTG_PHY))); 389 390 regmap_update_bits(priv->usb_glue_regmap, USB_R0, 391 USB_R0_U2D_ACT, USB_R0_U2D_ACT); 392 regmap_update_bits(priv->usb_glue_regmap, USB_R0, 393 USB_R0_U2D_SS_SCALEDOWN_MODE_MASK, 0); 394 regmap_update_bits(priv->usb_glue_regmap, USB_R4, 395 USB_R4_P21_SLEEP_M0, USB_R4_P21_SLEEP_M0); 396 } else { 397 if (priv->otg_mode != USB_DR_MODE_OTG && 398 priv->drvdata->otg_phy_host_port_disable) { 399 regmap_update_bits(priv->usb_glue_regmap, USB_R1, 400 USB_R1_U3H_HOST_U2_PORT_DISABLE_MASK, 0); 401 msleep(500); 402 } 403 regmap_update_bits(priv->usb_glue_regmap, USB_R0, 404 USB_R0_U2D_ACT, 0); 405 regmap_update_bits(priv->usb_glue_regmap, USB_R4, 406 USB_R4_P21_SLEEP_M0, 0); 407 } 408 } 409 410 static int dwc3_meson_g12a_usb_init_glue(struct dwc3_meson_g12a *priv, 411 enum phy_mode mode) 412 { 413 int ret; 414 415 ret = dwc3_meson_g12a_usb2_init(priv, mode); 416 if (ret) 417 return ret; 418 419 regmap_update_bits(priv->usb_glue_regmap, USB_R1, 420 USB_R1_U3H_FLADJ_30MHZ_REG_MASK, 421 FIELD_PREP(USB_R1_U3H_FLADJ_30MHZ_REG_MASK, 0x20)); 422 423 regmap_update_bits(priv->usb_glue_regmap, USB_R5, 424 USB_R5_ID_DIG_EN_0, 425 USB_R5_ID_DIG_EN_0); 426 regmap_update_bits(priv->usb_glue_regmap, USB_R5, 427 USB_R5_ID_DIG_EN_1, 428 USB_R5_ID_DIG_EN_1); 429 regmap_update_bits(priv->usb_glue_regmap, USB_R5, 430 USB_R5_ID_DIG_TH_MASK, 431 FIELD_PREP(USB_R5_ID_DIG_TH_MASK, 0xff)); 432 433 /* If we have an actual SuperSpeed port, initialize it */ 434 if (priv->usb3_ports) 435 dwc3_meson_g12a_usb3_init(priv); 436 437 dwc3_meson_g12a_usb_otg_apply_mode(priv, mode); 438 439 return 0; 440 } 441 442 static const struct regmap_config phy_meson_g12a_usb_glue_regmap_conf = { 443 .name = "usb-glue", 444 .reg_bits = 8, 445 .val_bits = 32, 446 .reg_stride = 4, 447 .max_register = USB_R5, 448 }; 449 450 static int dwc3_meson_g12a_get_phys(struct dwc3_meson_g12a *priv) 451 { 452 const char *phy_name; 453 int i; 454 455 for (i = 0 ; i < priv->drvdata->num_phys ; ++i) { 456 phy_name = priv->drvdata->phy_names[i]; 457 priv->phys[i] = devm_phy_optional_get(priv->dev, phy_name); 458 if (!priv->phys[i]) 459 continue; 460 461 if (IS_ERR(priv->phys[i])) 462 return PTR_ERR(priv->phys[i]); 463 464 if (strstr(phy_name, "usb3")) 465 priv->usb3_ports++; 466 else 467 priv->usb2_ports++; 468 } 469 470 dev_info(priv->dev, "USB2 ports: %d\n", priv->usb2_ports); 471 dev_info(priv->dev, "USB3 ports: %d\n", priv->usb3_ports); 472 473 return 0; 474 } 475 476 static enum phy_mode dwc3_meson_g12a_get_id(struct dwc3_meson_g12a *priv) 477 { 478 u32 reg; 479 480 regmap_read(priv->usb_glue_regmap, USB_R5, ®); 481 482 if (reg & (USB_R5_ID_DIG_SYNC | USB_R5_ID_DIG_REG)) 483 return PHY_MODE_USB_DEVICE; 484 485 return PHY_MODE_USB_HOST; 486 } 487 488 static int dwc3_meson_g12a_otg_mode_set(struct dwc3_meson_g12a *priv, 489 enum phy_mode mode) 490 { 491 int ret; 492 493 if (!priv->drvdata->otg_switch_supported || !priv->phys[USB2_OTG_PHY]) 494 return -EINVAL; 495 496 if (mode == PHY_MODE_USB_HOST) 497 dev_info(priv->dev, "switching to Host Mode\n"); 498 else 499 dev_info(priv->dev, "switching to Device Mode\n"); 500 501 if (priv->vbus) { 502 if (mode == PHY_MODE_USB_DEVICE) 503 ret = regulator_disable(priv->vbus); 504 else 505 ret = regulator_enable(priv->vbus); 506 if (ret) 507 return ret; 508 } 509 510 priv->otg_phy_mode = mode; 511 512 ret = priv->drvdata->set_phy_mode(priv, USB2_OTG_PHY, mode); 513 if (ret) 514 return ret; 515 516 dwc3_meson_g12a_usb_otg_apply_mode(priv, mode); 517 518 return 0; 519 } 520 521 static int dwc3_meson_g12a_role_set(struct usb_role_switch *sw, 522 enum usb_role role) 523 { 524 struct dwc3_meson_g12a *priv = usb_role_switch_get_drvdata(sw); 525 enum phy_mode mode; 526 527 if (role == USB_ROLE_NONE) 528 return 0; 529 530 mode = (role == USB_ROLE_HOST) ? PHY_MODE_USB_HOST 531 : PHY_MODE_USB_DEVICE; 532 533 if (mode == priv->otg_phy_mode) 534 return 0; 535 536 if (priv->drvdata->otg_phy_host_port_disable) 537 dev_warn_once(priv->dev, "Broken manual OTG switch\n"); 538 539 return dwc3_meson_g12a_otg_mode_set(priv, mode); 540 } 541 542 static enum usb_role dwc3_meson_g12a_role_get(struct usb_role_switch *sw) 543 { 544 struct dwc3_meson_g12a *priv = usb_role_switch_get_drvdata(sw); 545 546 return priv->otg_phy_mode == PHY_MODE_USB_HOST ? 547 USB_ROLE_HOST : USB_ROLE_DEVICE; 548 } 549 550 static irqreturn_t dwc3_meson_g12a_irq_thread(int irq, void *data) 551 { 552 struct dwc3_meson_g12a *priv = data; 553 enum phy_mode otg_id; 554 555 otg_id = dwc3_meson_g12a_get_id(priv); 556 if (otg_id != priv->otg_phy_mode) { 557 if (dwc3_meson_g12a_otg_mode_set(priv, otg_id)) 558 dev_warn(priv->dev, "Failed to switch OTG mode\n"); 559 } 560 561 regmap_update_bits(priv->usb_glue_regmap, USB_R5, 562 USB_R5_ID_DIG_IRQ, 0); 563 564 return IRQ_HANDLED; 565 } 566 567 static struct device *dwc3_meson_g12_find_child(struct device *dev, 568 const char *compatible) 569 { 570 struct platform_device *pdev; 571 struct device_node *np; 572 573 np = of_get_compatible_child(dev->of_node, compatible); 574 if (!np) 575 return NULL; 576 577 pdev = of_find_device_by_node(np); 578 of_node_put(np); 579 if (!pdev) 580 return NULL; 581 582 return &pdev->dev; 583 } 584 585 static int dwc3_meson_g12a_otg_init(struct platform_device *pdev, 586 struct dwc3_meson_g12a *priv) 587 { 588 enum phy_mode otg_id; 589 int ret, irq; 590 struct device *dev = &pdev->dev; 591 592 if (!priv->drvdata->otg_switch_supported) 593 return 0; 594 595 if (priv->otg_mode == USB_DR_MODE_OTG) { 596 /* Ack irq before registering */ 597 regmap_update_bits(priv->usb_glue_regmap, USB_R5, 598 USB_R5_ID_DIG_IRQ, 0); 599 600 irq = platform_get_irq(pdev, 0); 601 if (irq < 0) 602 return irq; 603 ret = devm_request_threaded_irq(&pdev->dev, irq, NULL, 604 dwc3_meson_g12a_irq_thread, 605 IRQF_ONESHOT, pdev->name, priv); 606 if (ret) 607 return ret; 608 } 609 610 /* Setup OTG mode corresponding to the ID pin */ 611 if (priv->otg_mode == USB_DR_MODE_OTG) { 612 otg_id = dwc3_meson_g12a_get_id(priv); 613 if (otg_id != priv->otg_phy_mode) { 614 if (dwc3_meson_g12a_otg_mode_set(priv, otg_id)) 615 dev_warn(dev, "Failed to switch OTG mode\n"); 616 } 617 } 618 619 /* Setup role switcher */ 620 priv->switch_desc.usb2_port = dwc3_meson_g12_find_child(dev, 621 "snps,dwc3"); 622 priv->switch_desc.udc = dwc3_meson_g12_find_child(dev, "snps,dwc2"); 623 priv->switch_desc.allow_userspace_control = true; 624 priv->switch_desc.set = dwc3_meson_g12a_role_set; 625 priv->switch_desc.get = dwc3_meson_g12a_role_get; 626 priv->switch_desc.driver_data = priv; 627 628 priv->role_switch = usb_role_switch_register(dev, &priv->switch_desc); 629 if (IS_ERR(priv->role_switch)) 630 dev_warn(dev, "Unable to register Role Switch\n"); 631 632 return 0; 633 } 634 635 static int dwc3_meson_gxl_setup_regmaps(struct dwc3_meson_g12a *priv, 636 void __iomem *base) 637 { 638 /* GXL controls the PHY mode in the PHY registers unlike G12A */ 639 priv->usb_glue_regmap = devm_regmap_init_mmio(priv->dev, base, 640 &phy_meson_g12a_usb_glue_regmap_conf); 641 return PTR_ERR_OR_ZERO(priv->usb_glue_regmap); 642 } 643 644 static int dwc3_meson_g12a_setup_regmaps(struct dwc3_meson_g12a *priv, 645 void __iomem *base) 646 { 647 int i; 648 649 priv->usb_glue_regmap = devm_regmap_init_mmio(priv->dev, 650 base + G12A_GLUE_OFFSET, 651 &phy_meson_g12a_usb_glue_regmap_conf); 652 if (IS_ERR(priv->usb_glue_regmap)) 653 return PTR_ERR(priv->usb_glue_regmap); 654 655 /* Create a regmap for each USB2 PHY control register set */ 656 for (i = 0; i < priv->drvdata->num_phys; i++) { 657 struct regmap_config u2p_regmap_config = { 658 .reg_bits = 8, 659 .val_bits = 32, 660 .reg_stride = 4, 661 .max_register = U2P_R1, 662 }; 663 664 if (!strstr(priv->drvdata->phy_names[i], "usb2")) 665 continue; 666 667 u2p_regmap_config.name = devm_kasprintf(priv->dev, GFP_KERNEL, 668 "u2p-%d", i); 669 if (!u2p_regmap_config.name) 670 return -ENOMEM; 671 672 priv->u2p_regmap[i] = devm_regmap_init_mmio(priv->dev, 673 base + (i * U2P_REG_SIZE), 674 &u2p_regmap_config); 675 if (IS_ERR(priv->u2p_regmap[i])) 676 return PTR_ERR(priv->u2p_regmap[i]); 677 } 678 679 return 0; 680 } 681 682 static int dwc3_meson_g12a_usb_init(struct dwc3_meson_g12a *priv) 683 { 684 return dwc3_meson_g12a_usb_init_glue(priv, priv->otg_phy_mode); 685 } 686 687 static int dwc3_meson_gxl_usb_init(struct dwc3_meson_g12a *priv) 688 { 689 return dwc3_meson_g12a_usb_init_glue(priv, PHY_MODE_USB_DEVICE); 690 } 691 692 static int dwc3_meson_gxl_usb_post_init(struct dwc3_meson_g12a *priv) 693 { 694 int ret; 695 696 ret = priv->drvdata->set_phy_mode(priv, USB2_OTG_PHY, 697 priv->otg_phy_mode); 698 if (ret) 699 return ret; 700 701 dwc3_meson_g12a_usb_otg_apply_mode(priv, priv->otg_phy_mode); 702 703 return 0; 704 } 705 706 static int dwc3_meson_g12a_probe(struct platform_device *pdev) 707 { 708 struct dwc3_meson_g12a *priv; 709 struct device *dev = &pdev->dev; 710 struct device_node *np = dev->of_node; 711 void __iomem *base; 712 int ret, i; 713 714 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); 715 if (!priv) 716 return -ENOMEM; 717 718 base = devm_platform_ioremap_resource(pdev, 0); 719 if (IS_ERR(base)) 720 return PTR_ERR(base); 721 722 priv->drvdata = of_device_get_match_data(&pdev->dev); 723 priv->dev = dev; 724 725 priv->vbus = devm_regulator_get_optional(dev, "vbus"); 726 if (IS_ERR(priv->vbus)) { 727 if (PTR_ERR(priv->vbus) == -EPROBE_DEFER) 728 return PTR_ERR(priv->vbus); 729 priv->vbus = NULL; 730 } 731 732 ret = devm_clk_bulk_get(dev, 733 priv->drvdata->num_clks, 734 priv->drvdata->clks); 735 if (ret) 736 return ret; 737 738 ret = clk_bulk_prepare_enable(priv->drvdata->num_clks, 739 priv->drvdata->clks); 740 if (ret) 741 return ret; 742 743 platform_set_drvdata(pdev, priv); 744 745 priv->reset = devm_reset_control_get_shared(dev, NULL); 746 if (IS_ERR(priv->reset)) { 747 ret = PTR_ERR(priv->reset); 748 dev_err(dev, "failed to get device reset, err=%d\n", ret); 749 goto err_disable_clks; 750 } 751 752 ret = reset_control_reset(priv->reset); 753 if (ret) 754 goto err_disable_clks; 755 756 ret = dwc3_meson_g12a_get_phys(priv); 757 if (ret) 758 goto err_rearm; 759 760 ret = priv->drvdata->setup_regmaps(priv, base); 761 if (ret) 762 goto err_rearm; 763 764 if (priv->vbus) { 765 ret = regulator_enable(priv->vbus); 766 if (ret) 767 goto err_rearm; 768 } 769 770 /* Get dr_mode */ 771 priv->otg_mode = usb_get_dr_mode(dev); 772 773 if (priv->otg_mode == USB_DR_MODE_PERIPHERAL) 774 priv->otg_phy_mode = PHY_MODE_USB_DEVICE; 775 else 776 priv->otg_phy_mode = PHY_MODE_USB_HOST; 777 778 ret = priv->drvdata->usb_init(priv); 779 if (ret) 780 goto err_disable_regulator; 781 782 /* Init PHYs */ 783 for (i = 0 ; i < PHY_COUNT ; ++i) { 784 ret = phy_init(priv->phys[i]); 785 if (ret) 786 goto err_disable_regulator; 787 } 788 789 /* Set PHY Power */ 790 for (i = 0 ; i < PHY_COUNT ; ++i) { 791 ret = phy_power_on(priv->phys[i]); 792 if (ret) 793 goto err_phys_exit; 794 } 795 796 if (priv->drvdata->usb_post_init) { 797 ret = priv->drvdata->usb_post_init(priv); 798 if (ret) 799 goto err_phys_power; 800 } 801 802 ret = of_platform_populate(np, NULL, NULL, dev); 803 if (ret) 804 goto err_phys_power; 805 806 ret = dwc3_meson_g12a_otg_init(pdev, priv); 807 if (ret) 808 goto err_phys_power; 809 810 pm_runtime_set_active(dev); 811 pm_runtime_enable(dev); 812 pm_runtime_get_sync(dev); 813 814 return 0; 815 816 err_phys_power: 817 for (i = 0 ; i < PHY_COUNT ; ++i) 818 phy_power_off(priv->phys[i]); 819 820 err_phys_exit: 821 for (i = 0 ; i < PHY_COUNT ; ++i) 822 phy_exit(priv->phys[i]); 823 824 err_disable_regulator: 825 if (priv->vbus) 826 regulator_disable(priv->vbus); 827 828 err_rearm: 829 reset_control_rearm(priv->reset); 830 831 err_disable_clks: 832 clk_bulk_disable_unprepare(priv->drvdata->num_clks, 833 priv->drvdata->clks); 834 835 return ret; 836 } 837 838 static int dwc3_meson_g12a_remove(struct platform_device *pdev) 839 { 840 struct dwc3_meson_g12a *priv = platform_get_drvdata(pdev); 841 struct device *dev = &pdev->dev; 842 int i; 843 844 if (priv->drvdata->otg_switch_supported) 845 usb_role_switch_unregister(priv->role_switch); 846 847 of_platform_depopulate(dev); 848 849 for (i = 0 ; i < PHY_COUNT ; ++i) { 850 phy_power_off(priv->phys[i]); 851 phy_exit(priv->phys[i]); 852 } 853 854 pm_runtime_disable(dev); 855 pm_runtime_put_noidle(dev); 856 pm_runtime_set_suspended(dev); 857 858 reset_control_rearm(priv->reset); 859 860 clk_bulk_disable_unprepare(priv->drvdata->num_clks, 861 priv->drvdata->clks); 862 863 return 0; 864 } 865 866 static int __maybe_unused dwc3_meson_g12a_runtime_suspend(struct device *dev) 867 { 868 struct dwc3_meson_g12a *priv = dev_get_drvdata(dev); 869 870 clk_bulk_disable_unprepare(priv->drvdata->num_clks, 871 priv->drvdata->clks); 872 873 return 0; 874 } 875 876 static int __maybe_unused dwc3_meson_g12a_runtime_resume(struct device *dev) 877 { 878 struct dwc3_meson_g12a *priv = dev_get_drvdata(dev); 879 880 return clk_bulk_prepare_enable(priv->drvdata->num_clks, 881 priv->drvdata->clks); 882 } 883 884 static int __maybe_unused dwc3_meson_g12a_suspend(struct device *dev) 885 { 886 struct dwc3_meson_g12a *priv = dev_get_drvdata(dev); 887 int i, ret; 888 889 if (priv->vbus && priv->otg_phy_mode == PHY_MODE_USB_HOST) { 890 ret = regulator_disable(priv->vbus); 891 if (ret) 892 return ret; 893 } 894 895 for (i = 0 ; i < PHY_COUNT ; ++i) { 896 phy_power_off(priv->phys[i]); 897 phy_exit(priv->phys[i]); 898 } 899 900 reset_control_rearm(priv->reset); 901 902 return 0; 903 } 904 905 static int __maybe_unused dwc3_meson_g12a_resume(struct device *dev) 906 { 907 struct dwc3_meson_g12a *priv = dev_get_drvdata(dev); 908 int i, ret; 909 910 ret = reset_control_reset(priv->reset); 911 if (ret) 912 return ret; 913 914 ret = priv->drvdata->usb_init(priv); 915 if (ret) 916 return ret; 917 918 /* Init PHYs */ 919 for (i = 0 ; i < PHY_COUNT ; ++i) { 920 ret = phy_init(priv->phys[i]); 921 if (ret) 922 return ret; 923 } 924 925 /* Set PHY Power */ 926 for (i = 0 ; i < PHY_COUNT ; ++i) { 927 ret = phy_power_on(priv->phys[i]); 928 if (ret) 929 return ret; 930 } 931 932 if (priv->vbus && priv->otg_phy_mode == PHY_MODE_USB_HOST) { 933 ret = regulator_enable(priv->vbus); 934 if (ret) 935 return ret; 936 } 937 938 return 0; 939 } 940 941 static const struct dev_pm_ops dwc3_meson_g12a_dev_pm_ops = { 942 SET_SYSTEM_SLEEP_PM_OPS(dwc3_meson_g12a_suspend, dwc3_meson_g12a_resume) 943 SET_RUNTIME_PM_OPS(dwc3_meson_g12a_runtime_suspend, 944 dwc3_meson_g12a_runtime_resume, NULL) 945 }; 946 947 static const struct of_device_id dwc3_meson_g12a_match[] = { 948 { 949 .compatible = "amlogic,meson-gxl-usb-ctrl", 950 .data = &gxl_drvdata, 951 }, 952 { 953 .compatible = "amlogic,meson-gxm-usb-ctrl", 954 .data = &gxm_drvdata, 955 }, 956 { 957 .compatible = "amlogic,meson-axg-usb-ctrl", 958 .data = &axg_drvdata, 959 }, 960 { 961 .compatible = "amlogic,meson-g12a-usb-ctrl", 962 .data = &g12a_drvdata, 963 }, 964 { 965 .compatible = "amlogic,meson-a1-usb-ctrl", 966 .data = &a1_drvdata, 967 }, 968 { /* Sentinel */ } 969 }; 970 MODULE_DEVICE_TABLE(of, dwc3_meson_g12a_match); 971 972 static struct platform_driver dwc3_meson_g12a_driver = { 973 .probe = dwc3_meson_g12a_probe, 974 .remove = dwc3_meson_g12a_remove, 975 .driver = { 976 .name = "dwc3-meson-g12a", 977 .of_match_table = dwc3_meson_g12a_match, 978 .pm = &dwc3_meson_g12a_dev_pm_ops, 979 }, 980 }; 981 982 module_platform_driver(dwc3_meson_g12a_driver); 983 MODULE_LICENSE("GPL v2"); 984 MODULE_DESCRIPTION("Amlogic Meson G12A USB Glue Layer"); 985 MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); 986