xref: /linux/drivers/usb/chipidea/usbmisc_imx.c (revision e65e175b07bef5974045cc42238de99057669ca7)
1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3  * Copyright 2012 Freescale Semiconductor, Inc.
4  */
5 
6 #include <linux/module.h>
7 #include <linux/of_platform.h>
8 #include <linux/err.h>
9 #include <linux/io.h>
10 #include <linux/delay.h>
11 #include <linux/usb/otg.h>
12 
13 #include "ci_hdrc_imx.h"
14 
15 #define MX25_USB_PHY_CTRL_OFFSET	0x08
16 #define MX25_BM_EXTERNAL_VBUS_DIVIDER	BIT(23)
17 
18 #define MX25_EHCI_INTERFACE_SINGLE_UNI	(2 << 0)
19 #define MX25_EHCI_INTERFACE_DIFF_UNI	(0 << 0)
20 #define MX25_EHCI_INTERFACE_MASK	(0xf)
21 
22 #define MX25_OTG_SIC_SHIFT		29
23 #define MX25_OTG_SIC_MASK		(0x3 << MX25_OTG_SIC_SHIFT)
24 #define MX25_OTG_PM_BIT			BIT(24)
25 #define MX25_OTG_PP_BIT			BIT(11)
26 #define MX25_OTG_OCPOL_BIT		BIT(3)
27 
28 #define MX25_H1_SIC_SHIFT		21
29 #define MX25_H1_SIC_MASK		(0x3 << MX25_H1_SIC_SHIFT)
30 #define MX25_H1_PP_BIT			BIT(18)
31 #define MX25_H1_PM_BIT			BIT(16)
32 #define MX25_H1_IPPUE_UP_BIT		BIT(7)
33 #define MX25_H1_IPPUE_DOWN_BIT		BIT(6)
34 #define MX25_H1_TLL_BIT			BIT(5)
35 #define MX25_H1_USBTE_BIT		BIT(4)
36 #define MX25_H1_OCPOL_BIT		BIT(2)
37 
38 #define MX27_H1_PM_BIT			BIT(8)
39 #define MX27_H2_PM_BIT			BIT(16)
40 #define MX27_OTG_PM_BIT			BIT(24)
41 
42 #define MX53_USB_OTG_PHY_CTRL_0_OFFSET	0x08
43 #define MX53_USB_OTG_PHY_CTRL_1_OFFSET	0x0c
44 #define MX53_USB_CTRL_1_OFFSET	        0x10
45 #define MX53_USB_CTRL_1_H2_XCVR_CLK_SEL_MASK (0x11 << 2)
46 #define MX53_USB_CTRL_1_H2_XCVR_CLK_SEL_ULPI BIT(2)
47 #define MX53_USB_CTRL_1_H3_XCVR_CLK_SEL_MASK (0x11 << 6)
48 #define MX53_USB_CTRL_1_H3_XCVR_CLK_SEL_ULPI BIT(6)
49 #define MX53_USB_UH2_CTRL_OFFSET	0x14
50 #define MX53_USB_UH3_CTRL_OFFSET	0x18
51 #define MX53_USB_CLKONOFF_CTRL_OFFSET	0x24
52 #define MX53_USB_CLKONOFF_CTRL_H2_INT60CKOFF BIT(21)
53 #define MX53_USB_CLKONOFF_CTRL_H3_INT60CKOFF BIT(22)
54 #define MX53_BM_OVER_CUR_DIS_H1		BIT(5)
55 #define MX53_BM_OVER_CUR_DIS_OTG	BIT(8)
56 #define MX53_BM_OVER_CUR_DIS_UHx	BIT(30)
57 #define MX53_USB_CTRL_1_UH2_ULPI_EN	BIT(26)
58 #define MX53_USB_CTRL_1_UH3_ULPI_EN	BIT(27)
59 #define MX53_USB_UHx_CTRL_WAKE_UP_EN	BIT(7)
60 #define MX53_USB_UHx_CTRL_ULPI_INT_EN	BIT(8)
61 #define MX53_USB_PHYCTRL1_PLLDIV_MASK	0x3
62 #define MX53_USB_PLL_DIV_24_MHZ		0x01
63 
64 #define MX6_BM_NON_BURST_SETTING	BIT(1)
65 #define MX6_BM_OVER_CUR_DIS		BIT(7)
66 #define MX6_BM_OVER_CUR_POLARITY	BIT(8)
67 #define MX6_BM_PWR_POLARITY		BIT(9)
68 #define MX6_BM_WAKEUP_ENABLE		BIT(10)
69 #define MX6_BM_UTMI_ON_CLOCK		BIT(13)
70 #define MX6_BM_ID_WAKEUP		BIT(16)
71 #define MX6_BM_VBUS_WAKEUP		BIT(17)
72 #define MX6SX_BM_DPDM_WAKEUP_EN		BIT(29)
73 #define MX6_BM_WAKEUP_INTR		BIT(31)
74 
75 #define MX6_USB_HSIC_CTRL_OFFSET	0x10
76 /* Send resume signal without 480Mhz PHY clock */
77 #define MX6SX_BM_HSIC_AUTO_RESUME	BIT(23)
78 /* set before portsc.suspendM = 1 */
79 #define MX6_BM_HSIC_DEV_CONN		BIT(21)
80 /* HSIC enable */
81 #define MX6_BM_HSIC_EN			BIT(12)
82 /* Force HSIC module 480M clock on, even when in Host is in suspend mode */
83 #define MX6_BM_HSIC_CLK_ON		BIT(11)
84 
85 #define MX6_USB_OTG1_PHY_CTRL		0x18
86 /* For imx6dql, it is host-only controller, for later imx6, it is otg's */
87 #define MX6_USB_OTG2_PHY_CTRL		0x1c
88 #define MX6SX_USB_VBUS_WAKEUP_SOURCE(v)	(v << 8)
89 #define MX6SX_USB_VBUS_WAKEUP_SOURCE_VBUS	MX6SX_USB_VBUS_WAKEUP_SOURCE(0)
90 #define MX6SX_USB_VBUS_WAKEUP_SOURCE_AVALID	MX6SX_USB_VBUS_WAKEUP_SOURCE(1)
91 #define MX6SX_USB_VBUS_WAKEUP_SOURCE_BVALID	MX6SX_USB_VBUS_WAKEUP_SOURCE(2)
92 #define MX6SX_USB_VBUS_WAKEUP_SOURCE_SESS_END	MX6SX_USB_VBUS_WAKEUP_SOURCE(3)
93 
94 #define VF610_OVER_CUR_DIS		BIT(7)
95 
96 #define MX7D_USBNC_USB_CTRL2		0x4
97 #define MX7D_USB_VBUS_WAKEUP_SOURCE_MASK	0x3
98 #define MX7D_USB_VBUS_WAKEUP_SOURCE(v)		(v << 0)
99 #define MX7D_USB_VBUS_WAKEUP_SOURCE_VBUS	MX7D_USB_VBUS_WAKEUP_SOURCE(0)
100 #define MX7D_USB_VBUS_WAKEUP_SOURCE_AVALID	MX7D_USB_VBUS_WAKEUP_SOURCE(1)
101 #define MX7D_USB_VBUS_WAKEUP_SOURCE_BVALID	MX7D_USB_VBUS_WAKEUP_SOURCE(2)
102 #define MX7D_USB_VBUS_WAKEUP_SOURCE_SESS_END	MX7D_USB_VBUS_WAKEUP_SOURCE(3)
103 #define MX7D_USBNC_AUTO_RESUME				BIT(2)
104 /* The default DM/DP value is pull-down */
105 #define MX7D_USBNC_USB_CTRL2_OPMODE(v)			(v << 6)
106 #define MX7D_USBNC_USB_CTRL2_OPMODE_NON_DRIVING	MX7D_USBNC_USB_CTRL2_OPMODE(1)
107 #define MX7D_USBNC_USB_CTRL2_OPMODE_OVERRIDE_MASK	(BIT(7) | BIT(6))
108 #define MX7D_USBNC_USB_CTRL2_OPMODE_OVERRIDE_EN		BIT(8)
109 #define MX7D_USBNC_USB_CTRL2_DP_OVERRIDE_VAL		BIT(12)
110 #define MX7D_USBNC_USB_CTRL2_DP_OVERRIDE_EN		BIT(13)
111 #define MX7D_USBNC_USB_CTRL2_DM_OVERRIDE_VAL		BIT(14)
112 #define MX7D_USBNC_USB_CTRL2_DM_OVERRIDE_EN		BIT(15)
113 #define MX7D_USBNC_USB_CTRL2_DP_DM_MASK			(BIT(12) | BIT(13) | \
114 							BIT(14) | BIT(15))
115 
116 #define MX7D_USB_OTG_PHY_CFG1		0x30
117 #define MX7D_USB_OTG_PHY_CFG2_CHRG_CHRGSEL	BIT(0)
118 #define MX7D_USB_OTG_PHY_CFG2_CHRG_VDATDETENB0	BIT(1)
119 #define MX7D_USB_OTG_PHY_CFG2_CHRG_VDATSRCENB0	BIT(2)
120 #define MX7D_USB_OTG_PHY_CFG2_CHRG_DCDENB	BIT(3)
121 #define MX7D_USB_OTG_PHY_CFG2_DRVVBUS0		BIT(16)
122 
123 #define MX7D_USB_OTG_PHY_CFG2		0x34
124 
125 #define MX7D_USB_OTG_PHY_STATUS		0x3c
126 #define MX7D_USB_OTG_PHY_STATUS_LINE_STATE0	BIT(0)
127 #define MX7D_USB_OTG_PHY_STATUS_LINE_STATE1	BIT(1)
128 #define MX7D_USB_OTG_PHY_STATUS_VBUS_VLD	BIT(3)
129 #define MX7D_USB_OTG_PHY_STATUS_CHRGDET		BIT(29)
130 
131 #define MX7D_USB_OTG_PHY_CFG1		0x30
132 #define TXPREEMPAMPTUNE0_BIT		28
133 #define TXPREEMPAMPTUNE0_MASK		(3 << 28)
134 #define TXVREFTUNE0_BIT			20
135 #define TXVREFTUNE0_MASK		(0xf << 20)
136 
137 #define MX6_USB_OTG_WAKEUP_BITS (MX6_BM_WAKEUP_ENABLE | MX6_BM_VBUS_WAKEUP | \
138 				 MX6_BM_ID_WAKEUP)
139 
140 struct usbmisc_ops {
141 	/* It's called once when probe a usb device */
142 	int (*init)(struct imx_usbmisc_data *data);
143 	/* It's called once after adding a usb device */
144 	int (*post)(struct imx_usbmisc_data *data);
145 	/* It's called when we need to enable/disable usb wakeup */
146 	int (*set_wakeup)(struct imx_usbmisc_data *data, bool enabled);
147 	/* It's called before setting portsc.suspendM */
148 	int (*hsic_set_connect)(struct imx_usbmisc_data *data);
149 	/* It's called during suspend/resume */
150 	int (*hsic_set_clk)(struct imx_usbmisc_data *data, bool enabled);
151 	/* usb charger detection */
152 	int (*charger_detection)(struct imx_usbmisc_data *data);
153 	/* It's called when system resume from usb power lost */
154 	int (*power_lost_check)(struct imx_usbmisc_data *data);
155 };
156 
157 struct imx_usbmisc {
158 	void __iomem *base;
159 	spinlock_t lock;
160 	const struct usbmisc_ops *ops;
161 };
162 
163 static inline bool is_imx53_usbmisc(struct imx_usbmisc_data *data);
164 
165 static int usbmisc_imx25_init(struct imx_usbmisc_data *data)
166 {
167 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
168 	unsigned long flags;
169 	u32 val = 0;
170 
171 	if (data->index > 1)
172 		return -EINVAL;
173 
174 	spin_lock_irqsave(&usbmisc->lock, flags);
175 	switch (data->index) {
176 	case 0:
177 		val = readl(usbmisc->base);
178 		val &= ~(MX25_OTG_SIC_MASK | MX25_OTG_PP_BIT);
179 		val |= (MX25_EHCI_INTERFACE_DIFF_UNI & MX25_EHCI_INTERFACE_MASK) << MX25_OTG_SIC_SHIFT;
180 		val |= (MX25_OTG_PM_BIT | MX25_OTG_OCPOL_BIT);
181 
182 		/*
183 		 * If the polarity is not configured assume active high for
184 		 * historical reasons.
185 		 */
186 		if (data->oc_pol_configured && data->oc_pol_active_low)
187 			val &= ~MX25_OTG_OCPOL_BIT;
188 
189 		writel(val, usbmisc->base);
190 		break;
191 	case 1:
192 		val = readl(usbmisc->base);
193 		val &= ~(MX25_H1_SIC_MASK | MX25_H1_PP_BIT |  MX25_H1_IPPUE_UP_BIT);
194 		val |= (MX25_EHCI_INTERFACE_SINGLE_UNI & MX25_EHCI_INTERFACE_MASK) << MX25_H1_SIC_SHIFT;
195 		val |= (MX25_H1_PM_BIT | MX25_H1_OCPOL_BIT | MX25_H1_TLL_BIT |
196 			MX25_H1_USBTE_BIT | MX25_H1_IPPUE_DOWN_BIT);
197 
198 		/*
199 		 * If the polarity is not configured assume active high for
200 		 * historical reasons.
201 		 */
202 		if (data->oc_pol_configured && data->oc_pol_active_low)
203 			val &= ~MX25_H1_OCPOL_BIT;
204 
205 		writel(val, usbmisc->base);
206 
207 		break;
208 	}
209 	spin_unlock_irqrestore(&usbmisc->lock, flags);
210 
211 	return 0;
212 }
213 
214 static int usbmisc_imx25_post(struct imx_usbmisc_data *data)
215 {
216 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
217 	void __iomem *reg;
218 	unsigned long flags;
219 	u32 val;
220 
221 	if (data->index > 2)
222 		return -EINVAL;
223 
224 	if (data->index)
225 		return 0;
226 
227 	spin_lock_irqsave(&usbmisc->lock, flags);
228 	reg = usbmisc->base + MX25_USB_PHY_CTRL_OFFSET;
229 	val = readl(reg);
230 
231 	if (data->evdo)
232 		val |= MX25_BM_EXTERNAL_VBUS_DIVIDER;
233 	else
234 		val &= ~MX25_BM_EXTERNAL_VBUS_DIVIDER;
235 
236 	writel(val, reg);
237 	spin_unlock_irqrestore(&usbmisc->lock, flags);
238 	usleep_range(5000, 10000); /* needed to stabilize voltage */
239 
240 	return 0;
241 }
242 
243 static int usbmisc_imx27_init(struct imx_usbmisc_data *data)
244 {
245 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
246 	unsigned long flags;
247 	u32 val;
248 
249 	switch (data->index) {
250 	case 0:
251 		val = MX27_OTG_PM_BIT;
252 		break;
253 	case 1:
254 		val = MX27_H1_PM_BIT;
255 		break;
256 	case 2:
257 		val = MX27_H2_PM_BIT;
258 		break;
259 	default:
260 		return -EINVAL;
261 	}
262 
263 	spin_lock_irqsave(&usbmisc->lock, flags);
264 	if (data->disable_oc)
265 		val = readl(usbmisc->base) | val;
266 	else
267 		val = readl(usbmisc->base) & ~val;
268 	writel(val, usbmisc->base);
269 	spin_unlock_irqrestore(&usbmisc->lock, flags);
270 
271 	return 0;
272 }
273 
274 static int usbmisc_imx53_init(struct imx_usbmisc_data *data)
275 {
276 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
277 	void __iomem *reg = NULL;
278 	unsigned long flags;
279 	u32 val = 0;
280 
281 	if (data->index > 3)
282 		return -EINVAL;
283 
284 	/* Select a 24 MHz reference clock for the PHY  */
285 	val = readl(usbmisc->base + MX53_USB_OTG_PHY_CTRL_1_OFFSET);
286 	val &= ~MX53_USB_PHYCTRL1_PLLDIV_MASK;
287 	val |= MX53_USB_PLL_DIV_24_MHZ;
288 	writel(val, usbmisc->base + MX53_USB_OTG_PHY_CTRL_1_OFFSET);
289 
290 	spin_lock_irqsave(&usbmisc->lock, flags);
291 
292 	switch (data->index) {
293 	case 0:
294 		if (data->disable_oc) {
295 			reg = usbmisc->base + MX53_USB_OTG_PHY_CTRL_0_OFFSET;
296 			val = readl(reg) | MX53_BM_OVER_CUR_DIS_OTG;
297 			writel(val, reg);
298 		}
299 		break;
300 	case 1:
301 		if (data->disable_oc) {
302 			reg = usbmisc->base + MX53_USB_OTG_PHY_CTRL_0_OFFSET;
303 			val = readl(reg) | MX53_BM_OVER_CUR_DIS_H1;
304 			writel(val, reg);
305 		}
306 		break;
307 	case 2:
308 		if (data->ulpi) {
309 			/* set USBH2 into ULPI-mode. */
310 			reg = usbmisc->base + MX53_USB_CTRL_1_OFFSET;
311 			val = readl(reg) | MX53_USB_CTRL_1_UH2_ULPI_EN;
312 			/* select ULPI clock */
313 			val &= ~MX53_USB_CTRL_1_H2_XCVR_CLK_SEL_MASK;
314 			val |= MX53_USB_CTRL_1_H2_XCVR_CLK_SEL_ULPI;
315 			writel(val, reg);
316 			/* Set interrupt wake up enable */
317 			reg = usbmisc->base + MX53_USB_UH2_CTRL_OFFSET;
318 			val = readl(reg) | MX53_USB_UHx_CTRL_WAKE_UP_EN
319 				| MX53_USB_UHx_CTRL_ULPI_INT_EN;
320 			writel(val, reg);
321 			if (is_imx53_usbmisc(data)) {
322 				/* Disable internal 60Mhz clock */
323 				reg = usbmisc->base +
324 					MX53_USB_CLKONOFF_CTRL_OFFSET;
325 				val = readl(reg) |
326 					MX53_USB_CLKONOFF_CTRL_H2_INT60CKOFF;
327 				writel(val, reg);
328 			}
329 
330 		}
331 		if (data->disable_oc) {
332 			reg = usbmisc->base + MX53_USB_UH2_CTRL_OFFSET;
333 			val = readl(reg) | MX53_BM_OVER_CUR_DIS_UHx;
334 			writel(val, reg);
335 		}
336 		break;
337 	case 3:
338 		if (data->ulpi) {
339 			/* set USBH3 into ULPI-mode. */
340 			reg = usbmisc->base + MX53_USB_CTRL_1_OFFSET;
341 			val = readl(reg) | MX53_USB_CTRL_1_UH3_ULPI_EN;
342 			/* select ULPI clock */
343 			val &= ~MX53_USB_CTRL_1_H3_XCVR_CLK_SEL_MASK;
344 			val |= MX53_USB_CTRL_1_H3_XCVR_CLK_SEL_ULPI;
345 			writel(val, reg);
346 			/* Set interrupt wake up enable */
347 			reg = usbmisc->base + MX53_USB_UH3_CTRL_OFFSET;
348 			val = readl(reg) | MX53_USB_UHx_CTRL_WAKE_UP_EN
349 				| MX53_USB_UHx_CTRL_ULPI_INT_EN;
350 			writel(val, reg);
351 
352 			if (is_imx53_usbmisc(data)) {
353 				/* Disable internal 60Mhz clock */
354 				reg = usbmisc->base +
355 					MX53_USB_CLKONOFF_CTRL_OFFSET;
356 				val = readl(reg) |
357 					MX53_USB_CLKONOFF_CTRL_H3_INT60CKOFF;
358 				writel(val, reg);
359 			}
360 		}
361 		if (data->disable_oc) {
362 			reg = usbmisc->base + MX53_USB_UH3_CTRL_OFFSET;
363 			val = readl(reg) | MX53_BM_OVER_CUR_DIS_UHx;
364 			writel(val, reg);
365 		}
366 		break;
367 	}
368 
369 	spin_unlock_irqrestore(&usbmisc->lock, flags);
370 
371 	return 0;
372 }
373 
374 static u32 usbmisc_wakeup_setting(struct imx_usbmisc_data *data)
375 {
376 	u32 wakeup_setting = MX6_USB_OTG_WAKEUP_BITS;
377 
378 	if (data->ext_id || data->available_role != USB_DR_MODE_OTG)
379 		wakeup_setting &= ~MX6_BM_ID_WAKEUP;
380 
381 	if (data->ext_vbus || data->available_role == USB_DR_MODE_HOST)
382 		wakeup_setting &= ~MX6_BM_VBUS_WAKEUP;
383 
384 	return wakeup_setting;
385 }
386 
387 static int usbmisc_imx6q_set_wakeup
388 	(struct imx_usbmisc_data *data, bool enabled)
389 {
390 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
391 	unsigned long flags;
392 	u32 val;
393 	int ret = 0;
394 
395 	if (data->index > 3)
396 		return -EINVAL;
397 
398 	spin_lock_irqsave(&usbmisc->lock, flags);
399 	val = readl(usbmisc->base + data->index * 4);
400 	if (enabled) {
401 		val &= ~MX6_USB_OTG_WAKEUP_BITS;
402 		val |= usbmisc_wakeup_setting(data);
403 	} else {
404 		if (val & MX6_BM_WAKEUP_INTR)
405 			pr_debug("wakeup int at ci_hdrc.%d\n", data->index);
406 		val &= ~MX6_USB_OTG_WAKEUP_BITS;
407 	}
408 	writel(val, usbmisc->base + data->index * 4);
409 	spin_unlock_irqrestore(&usbmisc->lock, flags);
410 
411 	return ret;
412 }
413 
414 static int usbmisc_imx6q_init(struct imx_usbmisc_data *data)
415 {
416 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
417 	unsigned long flags;
418 	u32 reg;
419 
420 	if (data->index > 3)
421 		return -EINVAL;
422 
423 	spin_lock_irqsave(&usbmisc->lock, flags);
424 
425 	reg = readl(usbmisc->base + data->index * 4);
426 	if (data->disable_oc) {
427 		reg |= MX6_BM_OVER_CUR_DIS;
428 	} else {
429 		reg &= ~MX6_BM_OVER_CUR_DIS;
430 
431 		/*
432 		 * If the polarity is not configured keep it as setup by the
433 		 * bootloader.
434 		 */
435 		if (data->oc_pol_configured && data->oc_pol_active_low)
436 			reg |= MX6_BM_OVER_CUR_POLARITY;
437 		else if (data->oc_pol_configured)
438 			reg &= ~MX6_BM_OVER_CUR_POLARITY;
439 	}
440 	/* If the polarity is not set keep it as setup by the bootlader */
441 	if (data->pwr_pol == 1)
442 		reg |= MX6_BM_PWR_POLARITY;
443 	writel(reg, usbmisc->base + data->index * 4);
444 
445 	/* SoC non-burst setting */
446 	reg = readl(usbmisc->base + data->index * 4);
447 	writel(reg | MX6_BM_NON_BURST_SETTING,
448 			usbmisc->base + data->index * 4);
449 
450 	/* For HSIC controller */
451 	if (data->hsic) {
452 		reg = readl(usbmisc->base + data->index * 4);
453 		writel(reg | MX6_BM_UTMI_ON_CLOCK,
454 			usbmisc->base + data->index * 4);
455 		reg = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET
456 			+ (data->index - 2) * 4);
457 		reg |= MX6_BM_HSIC_EN | MX6_BM_HSIC_CLK_ON;
458 		writel(reg, usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET
459 			+ (data->index - 2) * 4);
460 	}
461 
462 	spin_unlock_irqrestore(&usbmisc->lock, flags);
463 
464 	usbmisc_imx6q_set_wakeup(data, false);
465 
466 	return 0;
467 }
468 
469 static int usbmisc_imx6_hsic_get_reg_offset(struct imx_usbmisc_data *data)
470 {
471 	int offset, ret = 0;
472 
473 	if (data->index == 2 || data->index == 3) {
474 		offset = (data->index - 2) * 4;
475 	} else if (data->index == 0) {
476 		/*
477 		 * For SoCs like i.MX7D and later, each USB controller has
478 		 * its own non-core register region. For SoCs before i.MX7D,
479 		 * the first two USB controllers are non-HSIC controllers.
480 		 */
481 		offset = 0;
482 	} else {
483 		dev_err(data->dev, "index is error for usbmisc\n");
484 		ret = -EINVAL;
485 	}
486 
487 	return ret ? ret : offset;
488 }
489 
490 static int usbmisc_imx6_hsic_set_connect(struct imx_usbmisc_data *data)
491 {
492 	unsigned long flags;
493 	u32 val;
494 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
495 	int offset;
496 
497 	spin_lock_irqsave(&usbmisc->lock, flags);
498 	offset = usbmisc_imx6_hsic_get_reg_offset(data);
499 	if (offset < 0) {
500 		spin_unlock_irqrestore(&usbmisc->lock, flags);
501 		return offset;
502 	}
503 
504 	val = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset);
505 	if (!(val & MX6_BM_HSIC_DEV_CONN))
506 		writel(val | MX6_BM_HSIC_DEV_CONN,
507 			usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset);
508 
509 	spin_unlock_irqrestore(&usbmisc->lock, flags);
510 
511 	return 0;
512 }
513 
514 static int usbmisc_imx6_hsic_set_clk(struct imx_usbmisc_data *data, bool on)
515 {
516 	unsigned long flags;
517 	u32 val;
518 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
519 	int offset;
520 
521 	spin_lock_irqsave(&usbmisc->lock, flags);
522 	offset = usbmisc_imx6_hsic_get_reg_offset(data);
523 	if (offset < 0) {
524 		spin_unlock_irqrestore(&usbmisc->lock, flags);
525 		return offset;
526 	}
527 
528 	val = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset);
529 	val |= MX6_BM_HSIC_EN | MX6_BM_HSIC_CLK_ON;
530 	if (on)
531 		val |= MX6_BM_HSIC_CLK_ON;
532 	else
533 		val &= ~MX6_BM_HSIC_CLK_ON;
534 
535 	writel(val, usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset);
536 	spin_unlock_irqrestore(&usbmisc->lock, flags);
537 
538 	return 0;
539 }
540 
541 
542 static int usbmisc_imx6sx_init(struct imx_usbmisc_data *data)
543 {
544 	void __iomem *reg = NULL;
545 	unsigned long flags;
546 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
547 	u32 val;
548 
549 	usbmisc_imx6q_init(data);
550 
551 	if (data->index == 0 || data->index == 1) {
552 		reg = usbmisc->base + MX6_USB_OTG1_PHY_CTRL + data->index * 4;
553 		spin_lock_irqsave(&usbmisc->lock, flags);
554 		/* Set vbus wakeup source as bvalid */
555 		val = readl(reg);
556 		writel(val | MX6SX_USB_VBUS_WAKEUP_SOURCE_BVALID, reg);
557 		/*
558 		 * Disable dp/dm wakeup in device mode when vbus is
559 		 * not there.
560 		 */
561 		val = readl(usbmisc->base + data->index * 4);
562 		writel(val & ~MX6SX_BM_DPDM_WAKEUP_EN,
563 			usbmisc->base + data->index * 4);
564 		spin_unlock_irqrestore(&usbmisc->lock, flags);
565 	}
566 
567 	/* For HSIC controller */
568 	if (data->hsic) {
569 		val = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET);
570 		val |= MX6SX_BM_HSIC_AUTO_RESUME;
571 		writel(val, usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET);
572 	}
573 
574 	return 0;
575 }
576 
577 static int usbmisc_vf610_init(struct imx_usbmisc_data *data)
578 {
579 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
580 	u32 reg;
581 
582 	/*
583 	 * Vybrid only has one misc register set, but in two different
584 	 * areas. These is reflected in two instances of this driver.
585 	 */
586 	if (data->index >= 1)
587 		return -EINVAL;
588 
589 	if (data->disable_oc) {
590 		reg = readl(usbmisc->base);
591 		writel(reg | VF610_OVER_CUR_DIS, usbmisc->base);
592 	}
593 
594 	return 0;
595 }
596 
597 static int usbmisc_imx7d_set_wakeup
598 	(struct imx_usbmisc_data *data, bool enabled)
599 {
600 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
601 	unsigned long flags;
602 	u32 val;
603 
604 	spin_lock_irqsave(&usbmisc->lock, flags);
605 	val = readl(usbmisc->base);
606 	if (enabled) {
607 		val &= ~MX6_USB_OTG_WAKEUP_BITS;
608 		val |= usbmisc_wakeup_setting(data);
609 		writel(val, usbmisc->base);
610 	} else {
611 		if (val & MX6_BM_WAKEUP_INTR)
612 			dev_dbg(data->dev, "wakeup int\n");
613 		writel(val & ~MX6_USB_OTG_WAKEUP_BITS, usbmisc->base);
614 	}
615 	spin_unlock_irqrestore(&usbmisc->lock, flags);
616 
617 	return 0;
618 }
619 
620 static int usbmisc_imx7d_init(struct imx_usbmisc_data *data)
621 {
622 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
623 	unsigned long flags;
624 	u32 reg;
625 
626 	if (data->index >= 1)
627 		return -EINVAL;
628 
629 	spin_lock_irqsave(&usbmisc->lock, flags);
630 	reg = readl(usbmisc->base);
631 	if (data->disable_oc) {
632 		reg |= MX6_BM_OVER_CUR_DIS;
633 	} else {
634 		reg &= ~MX6_BM_OVER_CUR_DIS;
635 
636 		/*
637 		 * If the polarity is not configured keep it as setup by the
638 		 * bootloader.
639 		 */
640 		if (data->oc_pol_configured && data->oc_pol_active_low)
641 			reg |= MX6_BM_OVER_CUR_POLARITY;
642 		else if (data->oc_pol_configured)
643 			reg &= ~MX6_BM_OVER_CUR_POLARITY;
644 	}
645 	/* If the polarity is not set keep it as setup by the bootlader */
646 	if (data->pwr_pol == 1)
647 		reg |= MX6_BM_PWR_POLARITY;
648 	writel(reg, usbmisc->base);
649 
650 	/* SoC non-burst setting */
651 	reg = readl(usbmisc->base);
652 	writel(reg | MX6_BM_NON_BURST_SETTING, usbmisc->base);
653 
654 	if (!data->hsic) {
655 		reg = readl(usbmisc->base + MX7D_USBNC_USB_CTRL2);
656 		reg &= ~MX7D_USB_VBUS_WAKEUP_SOURCE_MASK;
657 		writel(reg | MX7D_USB_VBUS_WAKEUP_SOURCE_BVALID
658 			| MX7D_USBNC_AUTO_RESUME,
659 			usbmisc->base + MX7D_USBNC_USB_CTRL2);
660 		/* PHY tuning for signal quality */
661 		reg = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG1);
662 		if (data->emp_curr_control && data->emp_curr_control <=
663 			(TXPREEMPAMPTUNE0_MASK >> TXPREEMPAMPTUNE0_BIT)) {
664 			reg &= ~TXPREEMPAMPTUNE0_MASK;
665 			reg |= (data->emp_curr_control << TXPREEMPAMPTUNE0_BIT);
666 		}
667 
668 		if (data->dc_vol_level_adjust && data->dc_vol_level_adjust <=
669 			(TXVREFTUNE0_MASK >> TXVREFTUNE0_BIT)) {
670 			reg &= ~TXVREFTUNE0_MASK;
671 			reg |= (data->dc_vol_level_adjust << TXVREFTUNE0_BIT);
672 		}
673 
674 		writel(reg, usbmisc->base + MX7D_USB_OTG_PHY_CFG1);
675 	}
676 
677 	spin_unlock_irqrestore(&usbmisc->lock, flags);
678 
679 	usbmisc_imx7d_set_wakeup(data, false);
680 
681 	return 0;
682 }
683 
684 static int imx7d_charger_secondary_detection(struct imx_usbmisc_data *data)
685 {
686 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
687 	struct usb_phy *usb_phy = data->usb_phy;
688 	int val;
689 	unsigned long flags;
690 
691 	/* Clear VDATSRCENB0 to disable VDP_SRC and IDM_SNK required by BC 1.2 spec */
692 	spin_lock_irqsave(&usbmisc->lock, flags);
693 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
694 	val &= ~MX7D_USB_OTG_PHY_CFG2_CHRG_VDATSRCENB0;
695 	writel(val, usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
696 	spin_unlock_irqrestore(&usbmisc->lock, flags);
697 
698 	/* TVDMSRC_DIS */
699 	msleep(20);
700 
701 	/* VDM_SRC is connected to D- and IDP_SINK is connected to D+ */
702 	spin_lock_irqsave(&usbmisc->lock, flags);
703 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
704 	writel(val | MX7D_USB_OTG_PHY_CFG2_CHRG_VDATSRCENB0 |
705 			MX7D_USB_OTG_PHY_CFG2_CHRG_VDATDETENB0 |
706 			MX7D_USB_OTG_PHY_CFG2_CHRG_CHRGSEL,
707 				usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
708 	spin_unlock_irqrestore(&usbmisc->lock, flags);
709 
710 	/* TVDMSRC_ON */
711 	msleep(40);
712 
713 	/*
714 	 * Per BC 1.2, check voltage of D+:
715 	 * DCP: if greater than VDAT_REF;
716 	 * CDP: if less than VDAT_REF.
717 	 */
718 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_STATUS);
719 	if (val & MX7D_USB_OTG_PHY_STATUS_CHRGDET) {
720 		dev_dbg(data->dev, "It is a dedicate charging port\n");
721 		usb_phy->chg_type = DCP_TYPE;
722 	} else {
723 		dev_dbg(data->dev, "It is a charging downstream port\n");
724 		usb_phy->chg_type = CDP_TYPE;
725 	}
726 
727 	return 0;
728 }
729 
730 static void imx7_disable_charger_detector(struct imx_usbmisc_data *data)
731 {
732 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
733 	unsigned long flags;
734 	u32 val;
735 
736 	spin_lock_irqsave(&usbmisc->lock, flags);
737 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
738 	val &= ~(MX7D_USB_OTG_PHY_CFG2_CHRG_DCDENB |
739 			MX7D_USB_OTG_PHY_CFG2_CHRG_VDATSRCENB0 |
740 			MX7D_USB_OTG_PHY_CFG2_CHRG_VDATDETENB0 |
741 			MX7D_USB_OTG_PHY_CFG2_CHRG_CHRGSEL);
742 	writel(val, usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
743 
744 	/* Set OPMODE to be 2'b00 and disable its override */
745 	val = readl(usbmisc->base + MX7D_USBNC_USB_CTRL2);
746 	val &= ~MX7D_USBNC_USB_CTRL2_OPMODE_OVERRIDE_MASK;
747 	writel(val, usbmisc->base + MX7D_USBNC_USB_CTRL2);
748 
749 	val = readl(usbmisc->base + MX7D_USBNC_USB_CTRL2);
750 	writel(val & ~MX7D_USBNC_USB_CTRL2_OPMODE_OVERRIDE_EN,
751 			usbmisc->base + MX7D_USBNC_USB_CTRL2);
752 	spin_unlock_irqrestore(&usbmisc->lock, flags);
753 }
754 
755 static int imx7d_charger_data_contact_detect(struct imx_usbmisc_data *data)
756 {
757 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
758 	unsigned long flags;
759 	u32 val;
760 	int i, data_pin_contact_count = 0;
761 
762 	/* Enable Data Contact Detect (DCD) per the USB BC 1.2 */
763 	spin_lock_irqsave(&usbmisc->lock, flags);
764 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
765 	writel(val | MX7D_USB_OTG_PHY_CFG2_CHRG_DCDENB,
766 			usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
767 	spin_unlock_irqrestore(&usbmisc->lock, flags);
768 
769 	for (i = 0; i < 100; i = i + 1) {
770 		val = readl(usbmisc->base + MX7D_USB_OTG_PHY_STATUS);
771 		if (!(val & MX7D_USB_OTG_PHY_STATUS_LINE_STATE0)) {
772 			if (data_pin_contact_count++ > 5)
773 				/* Data pin makes contact */
774 				break;
775 			usleep_range(5000, 10000);
776 		} else {
777 			data_pin_contact_count = 0;
778 			usleep_range(5000, 6000);
779 		}
780 	}
781 
782 	/* Disable DCD after finished data contact check */
783 	spin_lock_irqsave(&usbmisc->lock, flags);
784 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
785 	writel(val & ~MX7D_USB_OTG_PHY_CFG2_CHRG_DCDENB,
786 			usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
787 	spin_unlock_irqrestore(&usbmisc->lock, flags);
788 
789 	if (i == 100) {
790 		dev_err(data->dev,
791 			"VBUS is coming from a dedicated power supply.\n");
792 		return -ENXIO;
793 	}
794 
795 	return 0;
796 }
797 
798 static int imx7d_charger_primary_detection(struct imx_usbmisc_data *data)
799 {
800 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
801 	struct usb_phy *usb_phy = data->usb_phy;
802 	unsigned long flags;
803 	u32 val;
804 
805 	/* VDP_SRC is connected to D+ and IDM_SINK is connected to D- */
806 	spin_lock_irqsave(&usbmisc->lock, flags);
807 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
808 	val &= ~MX7D_USB_OTG_PHY_CFG2_CHRG_CHRGSEL;
809 	writel(val | MX7D_USB_OTG_PHY_CFG2_CHRG_VDATSRCENB0 |
810 			MX7D_USB_OTG_PHY_CFG2_CHRG_VDATDETENB0,
811 				usbmisc->base + MX7D_USB_OTG_PHY_CFG2);
812 	spin_unlock_irqrestore(&usbmisc->lock, flags);
813 
814 	/* TVDPSRC_ON */
815 	msleep(40);
816 
817 	/* Check if D- is less than VDAT_REF to determine an SDP per BC 1.2 */
818 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_STATUS);
819 	if (!(val & MX7D_USB_OTG_PHY_STATUS_CHRGDET)) {
820 		dev_dbg(data->dev, "It is a standard downstream port\n");
821 		usb_phy->chg_type = SDP_TYPE;
822 	}
823 
824 	return 0;
825 }
826 
827 /*
828  * Whole charger detection process:
829  * 1. OPMODE override to be non-driving
830  * 2. Data contact check
831  * 3. Primary detection
832  * 4. Secondary detection
833  * 5. Disable charger detection
834  */
835 static int imx7d_charger_detection(struct imx_usbmisc_data *data)
836 {
837 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
838 	struct usb_phy *usb_phy = data->usb_phy;
839 	unsigned long flags;
840 	u32 val;
841 	int ret;
842 
843 	/* Check if vbus is valid */
844 	val = readl(usbmisc->base + MX7D_USB_OTG_PHY_STATUS);
845 	if (!(val & MX7D_USB_OTG_PHY_STATUS_VBUS_VLD)) {
846 		dev_err(data->dev, "vbus is error\n");
847 		return -EINVAL;
848 	}
849 
850 	/*
851 	 * Keep OPMODE to be non-driving mode during the whole
852 	 * charger detection process.
853 	 */
854 	spin_lock_irqsave(&usbmisc->lock, flags);
855 	val = readl(usbmisc->base + MX7D_USBNC_USB_CTRL2);
856 	val &= ~MX7D_USBNC_USB_CTRL2_OPMODE_OVERRIDE_MASK;
857 	val |= MX7D_USBNC_USB_CTRL2_OPMODE_NON_DRIVING;
858 	writel(val, usbmisc->base + MX7D_USBNC_USB_CTRL2);
859 
860 	val = readl(usbmisc->base + MX7D_USBNC_USB_CTRL2);
861 	writel(val | MX7D_USBNC_USB_CTRL2_OPMODE_OVERRIDE_EN,
862 			usbmisc->base + MX7D_USBNC_USB_CTRL2);
863 	spin_unlock_irqrestore(&usbmisc->lock, flags);
864 
865 	ret = imx7d_charger_data_contact_detect(data);
866 	if (ret)
867 		return ret;
868 
869 	ret = imx7d_charger_primary_detection(data);
870 	if (!ret && usb_phy->chg_type != SDP_TYPE)
871 		ret = imx7d_charger_secondary_detection(data);
872 
873 	imx7_disable_charger_detector(data);
874 
875 	return ret;
876 }
877 
878 static int usbmisc_imx7ulp_init(struct imx_usbmisc_data *data)
879 {
880 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
881 	unsigned long flags;
882 	u32 reg;
883 
884 	if (data->index >= 1)
885 		return -EINVAL;
886 
887 	spin_lock_irqsave(&usbmisc->lock, flags);
888 	reg = readl(usbmisc->base);
889 	if (data->disable_oc) {
890 		reg |= MX6_BM_OVER_CUR_DIS;
891 	} else {
892 		reg &= ~MX6_BM_OVER_CUR_DIS;
893 
894 		/*
895 		 * If the polarity is not configured keep it as setup by the
896 		 * bootloader.
897 		 */
898 		if (data->oc_pol_configured && data->oc_pol_active_low)
899 			reg |= MX6_BM_OVER_CUR_POLARITY;
900 		else if (data->oc_pol_configured)
901 			reg &= ~MX6_BM_OVER_CUR_POLARITY;
902 	}
903 	/* If the polarity is not set keep it as setup by the bootlader */
904 	if (data->pwr_pol == 1)
905 		reg |= MX6_BM_PWR_POLARITY;
906 
907 	writel(reg, usbmisc->base);
908 
909 	/* SoC non-burst setting */
910 	reg = readl(usbmisc->base);
911 	writel(reg | MX6_BM_NON_BURST_SETTING, usbmisc->base);
912 
913 	if (data->hsic) {
914 		reg = readl(usbmisc->base);
915 		writel(reg | MX6_BM_UTMI_ON_CLOCK, usbmisc->base);
916 
917 		reg = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET);
918 		reg |= MX6_BM_HSIC_EN | MX6_BM_HSIC_CLK_ON;
919 		writel(reg, usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET);
920 
921 		/*
922 		 * For non-HSIC controller, the autoresume is enabled
923 		 * at MXS PHY driver (usbphy_ctrl bit18).
924 		 */
925 		reg = readl(usbmisc->base + MX7D_USBNC_USB_CTRL2);
926 		writel(reg | MX7D_USBNC_AUTO_RESUME,
927 			usbmisc->base + MX7D_USBNC_USB_CTRL2);
928 	} else {
929 		reg = readl(usbmisc->base + MX7D_USBNC_USB_CTRL2);
930 		reg &= ~MX7D_USB_VBUS_WAKEUP_SOURCE_MASK;
931 		writel(reg | MX7D_USB_VBUS_WAKEUP_SOURCE_BVALID,
932 			 usbmisc->base + MX7D_USBNC_USB_CTRL2);
933 	}
934 
935 	spin_unlock_irqrestore(&usbmisc->lock, flags);
936 
937 	usbmisc_imx7d_set_wakeup(data, false);
938 
939 	return 0;
940 }
941 
942 static int usbmisc_imx7d_power_lost_check(struct imx_usbmisc_data *data)
943 {
944 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
945 	unsigned long flags;
946 	u32 val;
947 
948 	spin_lock_irqsave(&usbmisc->lock, flags);
949 	val = readl(usbmisc->base);
950 	spin_unlock_irqrestore(&usbmisc->lock, flags);
951 	/*
952 	 * Here use a power on reset value to judge
953 	 * if the controller experienced a power lost
954 	 */
955 	if (val == 0x30001000)
956 		return 1;
957 	else
958 		return 0;
959 }
960 
961 static int usbmisc_imx6sx_power_lost_check(struct imx_usbmisc_data *data)
962 {
963 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
964 	unsigned long flags;
965 	u32 val;
966 
967 	spin_lock_irqsave(&usbmisc->lock, flags);
968 	val = readl(usbmisc->base + data->index * 4);
969 	spin_unlock_irqrestore(&usbmisc->lock, flags);
970 	/*
971 	 * Here use a power on reset value to judge
972 	 * if the controller experienced a power lost
973 	 */
974 	if (val == 0x30001000)
975 		return 1;
976 	else
977 		return 0;
978 }
979 
980 static const struct usbmisc_ops imx25_usbmisc_ops = {
981 	.init = usbmisc_imx25_init,
982 	.post = usbmisc_imx25_post,
983 };
984 
985 static const struct usbmisc_ops imx27_usbmisc_ops = {
986 	.init = usbmisc_imx27_init,
987 };
988 
989 static const struct usbmisc_ops imx51_usbmisc_ops = {
990 	.init = usbmisc_imx53_init,
991 };
992 
993 static const struct usbmisc_ops imx53_usbmisc_ops = {
994 	.init = usbmisc_imx53_init,
995 };
996 
997 static const struct usbmisc_ops imx6q_usbmisc_ops = {
998 	.set_wakeup = usbmisc_imx6q_set_wakeup,
999 	.init = usbmisc_imx6q_init,
1000 	.hsic_set_connect = usbmisc_imx6_hsic_set_connect,
1001 	.hsic_set_clk   = usbmisc_imx6_hsic_set_clk,
1002 };
1003 
1004 static const struct usbmisc_ops vf610_usbmisc_ops = {
1005 	.init = usbmisc_vf610_init,
1006 };
1007 
1008 static const struct usbmisc_ops imx6sx_usbmisc_ops = {
1009 	.set_wakeup = usbmisc_imx6q_set_wakeup,
1010 	.init = usbmisc_imx6sx_init,
1011 	.hsic_set_connect = usbmisc_imx6_hsic_set_connect,
1012 	.hsic_set_clk = usbmisc_imx6_hsic_set_clk,
1013 	.power_lost_check = usbmisc_imx6sx_power_lost_check,
1014 };
1015 
1016 static const struct usbmisc_ops imx7d_usbmisc_ops = {
1017 	.init = usbmisc_imx7d_init,
1018 	.set_wakeup = usbmisc_imx7d_set_wakeup,
1019 	.charger_detection = imx7d_charger_detection,
1020 	.power_lost_check = usbmisc_imx7d_power_lost_check,
1021 };
1022 
1023 static const struct usbmisc_ops imx7ulp_usbmisc_ops = {
1024 	.init = usbmisc_imx7ulp_init,
1025 	.set_wakeup = usbmisc_imx7d_set_wakeup,
1026 	.hsic_set_connect = usbmisc_imx6_hsic_set_connect,
1027 	.hsic_set_clk = usbmisc_imx6_hsic_set_clk,
1028 	.power_lost_check = usbmisc_imx7d_power_lost_check,
1029 };
1030 
1031 static inline bool is_imx53_usbmisc(struct imx_usbmisc_data *data)
1032 {
1033 	struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
1034 
1035 	return usbmisc->ops == &imx53_usbmisc_ops;
1036 }
1037 
1038 int imx_usbmisc_init(struct imx_usbmisc_data *data)
1039 {
1040 	struct imx_usbmisc *usbmisc;
1041 
1042 	if (!data)
1043 		return 0;
1044 
1045 	usbmisc = dev_get_drvdata(data->dev);
1046 	if (!usbmisc->ops->init)
1047 		return 0;
1048 	return usbmisc->ops->init(data);
1049 }
1050 EXPORT_SYMBOL_GPL(imx_usbmisc_init);
1051 
1052 int imx_usbmisc_init_post(struct imx_usbmisc_data *data)
1053 {
1054 	struct imx_usbmisc *usbmisc;
1055 	int ret = 0;
1056 
1057 	if (!data)
1058 		return 0;
1059 
1060 	usbmisc = dev_get_drvdata(data->dev);
1061 	if (usbmisc->ops->post)
1062 		ret = usbmisc->ops->post(data);
1063 	if (ret) {
1064 		dev_err(data->dev, "post init failed, ret=%d\n", ret);
1065 		return ret;
1066 	}
1067 
1068 	if (usbmisc->ops->set_wakeup)
1069 		ret = usbmisc->ops->set_wakeup(data, false);
1070 	if (ret) {
1071 		dev_err(data->dev, "set_wakeup failed, ret=%d\n", ret);
1072 		return ret;
1073 	}
1074 
1075 	return 0;
1076 }
1077 EXPORT_SYMBOL_GPL(imx_usbmisc_init_post);
1078 
1079 int imx_usbmisc_hsic_set_connect(struct imx_usbmisc_data *data)
1080 {
1081 	struct imx_usbmisc *usbmisc;
1082 
1083 	if (!data)
1084 		return 0;
1085 
1086 	usbmisc = dev_get_drvdata(data->dev);
1087 	if (!usbmisc->ops->hsic_set_connect || !data->hsic)
1088 		return 0;
1089 	return usbmisc->ops->hsic_set_connect(data);
1090 }
1091 EXPORT_SYMBOL_GPL(imx_usbmisc_hsic_set_connect);
1092 
1093 int imx_usbmisc_charger_detection(struct imx_usbmisc_data *data, bool connect)
1094 {
1095 	struct imx_usbmisc *usbmisc;
1096 	struct usb_phy *usb_phy;
1097 	int ret = 0;
1098 
1099 	if (!data)
1100 		return -EINVAL;
1101 
1102 	usbmisc = dev_get_drvdata(data->dev);
1103 	usb_phy = data->usb_phy;
1104 	if (!usbmisc->ops->charger_detection)
1105 		return -ENOTSUPP;
1106 
1107 	if (connect) {
1108 		ret = usbmisc->ops->charger_detection(data);
1109 		if (ret) {
1110 			dev_err(data->dev,
1111 					"Error occurs during detection: %d\n",
1112 					ret);
1113 			usb_phy->chg_state = USB_CHARGER_ABSENT;
1114 		} else {
1115 			usb_phy->chg_state = USB_CHARGER_PRESENT;
1116 		}
1117 	} else {
1118 		usb_phy->chg_state = USB_CHARGER_ABSENT;
1119 		usb_phy->chg_type = UNKNOWN_TYPE;
1120 	}
1121 	return ret;
1122 }
1123 EXPORT_SYMBOL_GPL(imx_usbmisc_charger_detection);
1124 
1125 int imx_usbmisc_suspend(struct imx_usbmisc_data *data, bool wakeup)
1126 {
1127 	struct imx_usbmisc *usbmisc;
1128 	int ret = 0;
1129 
1130 	if (!data)
1131 		return 0;
1132 
1133 	usbmisc = dev_get_drvdata(data->dev);
1134 
1135 	if (wakeup && usbmisc->ops->set_wakeup)
1136 		ret = usbmisc->ops->set_wakeup(data, true);
1137 	if (ret) {
1138 		dev_err(data->dev, "set_wakeup failed, ret=%d\n", ret);
1139 		return ret;
1140 	}
1141 
1142 	if (usbmisc->ops->hsic_set_clk && data->hsic)
1143 		ret = usbmisc->ops->hsic_set_clk(data, false);
1144 	if (ret) {
1145 		dev_err(data->dev, "set_wakeup failed, ret=%d\n", ret);
1146 		return ret;
1147 	}
1148 
1149 	return ret;
1150 }
1151 EXPORT_SYMBOL_GPL(imx_usbmisc_suspend);
1152 
1153 int imx_usbmisc_resume(struct imx_usbmisc_data *data, bool wakeup)
1154 {
1155 	struct imx_usbmisc *usbmisc;
1156 	int ret = 0;
1157 
1158 	if (!data)
1159 		return 0;
1160 
1161 	usbmisc = dev_get_drvdata(data->dev);
1162 
1163 	if (usbmisc->ops->power_lost_check)
1164 		ret = usbmisc->ops->power_lost_check(data);
1165 	if (ret > 0) {
1166 		/* re-init if resume from power lost */
1167 		ret = imx_usbmisc_init(data);
1168 		if (ret) {
1169 			dev_err(data->dev, "re-init failed, ret=%d\n", ret);
1170 			return ret;
1171 		}
1172 	}
1173 
1174 	if (wakeup && usbmisc->ops->set_wakeup)
1175 		ret = usbmisc->ops->set_wakeup(data, false);
1176 	if (ret) {
1177 		dev_err(data->dev, "set_wakeup failed, ret=%d\n", ret);
1178 		return ret;
1179 	}
1180 
1181 	if (usbmisc->ops->hsic_set_clk && data->hsic)
1182 		ret = usbmisc->ops->hsic_set_clk(data, true);
1183 	if (ret) {
1184 		dev_err(data->dev, "set_wakeup failed, ret=%d\n", ret);
1185 		goto hsic_set_clk_fail;
1186 	}
1187 
1188 	return 0;
1189 
1190 hsic_set_clk_fail:
1191 	if (wakeup && usbmisc->ops->set_wakeup)
1192 		usbmisc->ops->set_wakeup(data, true);
1193 	return ret;
1194 }
1195 EXPORT_SYMBOL_GPL(imx_usbmisc_resume);
1196 
1197 static const struct of_device_id usbmisc_imx_dt_ids[] = {
1198 	{
1199 		.compatible = "fsl,imx25-usbmisc",
1200 		.data = &imx25_usbmisc_ops,
1201 	},
1202 	{
1203 		.compatible = "fsl,imx35-usbmisc",
1204 		.data = &imx25_usbmisc_ops,
1205 	},
1206 	{
1207 		.compatible = "fsl,imx27-usbmisc",
1208 		.data = &imx27_usbmisc_ops,
1209 	},
1210 	{
1211 		.compatible = "fsl,imx51-usbmisc",
1212 		.data = &imx51_usbmisc_ops,
1213 	},
1214 	{
1215 		.compatible = "fsl,imx53-usbmisc",
1216 		.data = &imx53_usbmisc_ops,
1217 	},
1218 	{
1219 		.compatible = "fsl,imx6q-usbmisc",
1220 		.data = &imx6q_usbmisc_ops,
1221 	},
1222 	{
1223 		.compatible = "fsl,vf610-usbmisc",
1224 		.data = &vf610_usbmisc_ops,
1225 	},
1226 	{
1227 		.compatible = "fsl,imx6sx-usbmisc",
1228 		.data = &imx6sx_usbmisc_ops,
1229 	},
1230 	{
1231 		.compatible = "fsl,imx6ul-usbmisc",
1232 		.data = &imx6sx_usbmisc_ops,
1233 	},
1234 	{
1235 		.compatible = "fsl,imx7d-usbmisc",
1236 		.data = &imx7d_usbmisc_ops,
1237 	},
1238 	{
1239 		.compatible = "fsl,imx7ulp-usbmisc",
1240 		.data = &imx7ulp_usbmisc_ops,
1241 	},
1242 	{ /* sentinel */ }
1243 };
1244 MODULE_DEVICE_TABLE(of, usbmisc_imx_dt_ids);
1245 
1246 static int usbmisc_imx_probe(struct platform_device *pdev)
1247 {
1248 	struct imx_usbmisc *data;
1249 
1250 	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
1251 	if (!data)
1252 		return -ENOMEM;
1253 
1254 	spin_lock_init(&data->lock);
1255 
1256 	data->base = devm_platform_ioremap_resource(pdev, 0);
1257 	if (IS_ERR(data->base))
1258 		return PTR_ERR(data->base);
1259 
1260 	data->ops = of_device_get_match_data(&pdev->dev);
1261 	platform_set_drvdata(pdev, data);
1262 
1263 	return 0;
1264 }
1265 
1266 static int usbmisc_imx_remove(struct platform_device *pdev)
1267 {
1268 	return 0;
1269 }
1270 
1271 static struct platform_driver usbmisc_imx_driver = {
1272 	.probe = usbmisc_imx_probe,
1273 	.remove = usbmisc_imx_remove,
1274 	.driver = {
1275 		.name = "usbmisc_imx",
1276 		.of_match_table = usbmisc_imx_dt_ids,
1277 	 },
1278 };
1279 
1280 module_platform_driver(usbmisc_imx_driver);
1281 
1282 MODULE_ALIAS("platform:usbmisc-imx");
1283 MODULE_LICENSE("GPL");
1284 MODULE_DESCRIPTION("driver for imx usb non-core registers");
1285 MODULE_AUTHOR("Richard Zhao <richard.zhao@freescale.com>");
1286