1 /* sunsab.c: ASYNC Driver for the SIEMENS SAB82532 DUSCC. 2 * 3 * Copyright (C) 1997 Eddie C. Dost (ecd@skynet.be) 4 * Copyright (C) 2002, 2006 David S. Miller (davem@davemloft.net) 5 * 6 * Rewrote buffer handling to use CIRC(Circular Buffer) macros. 7 * Maxim Krasnyanskiy <maxk@qualcomm.com> 8 * 9 * Fixed to use tty_get_baud_rate, and to allow for arbitrary baud 10 * rates to be programmed into the UART. Also eliminated a lot of 11 * duplicated code in the console setup. 12 * Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12 13 * 14 * Ported to new 2.5.x UART layer. 15 * David S. Miller <davem@davemloft.net> 16 */ 17 18 #include <linux/module.h> 19 #include <linux/kernel.h> 20 #include <linux/errno.h> 21 #include <linux/tty.h> 22 #include <linux/tty_flip.h> 23 #include <linux/major.h> 24 #include <linux/string.h> 25 #include <linux/ptrace.h> 26 #include <linux/ioport.h> 27 #include <linux/circ_buf.h> 28 #include <linux/serial.h> 29 #include <linux/sysrq.h> 30 #include <linux/console.h> 31 #include <linux/spinlock.h> 32 #include <linux/slab.h> 33 #include <linux/delay.h> 34 #include <linux/init.h> 35 #include <linux/of_device.h> 36 37 #include <asm/io.h> 38 #include <asm/irq.h> 39 #include <asm/prom.h> 40 #include <asm/setup.h> 41 42 #if defined(CONFIG_SERIAL_SUNSAB_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) 43 #define SUPPORT_SYSRQ 44 #endif 45 46 #include <linux/serial_core.h> 47 #include <linux/sunserialcore.h> 48 49 #include "sunsab.h" 50 51 struct uart_sunsab_port { 52 struct uart_port port; /* Generic UART port */ 53 union sab82532_async_regs __iomem *regs; /* Chip registers */ 54 unsigned long irqflags; /* IRQ state flags */ 55 int dsr; /* Current DSR state */ 56 unsigned int cec_timeout; /* Chip poll timeout... */ 57 unsigned int tec_timeout; /* likewise */ 58 unsigned char interrupt_mask0;/* ISR0 masking */ 59 unsigned char interrupt_mask1;/* ISR1 masking */ 60 unsigned char pvr_dtr_bit; /* Which PVR bit is DTR */ 61 unsigned char pvr_dsr_bit; /* Which PVR bit is DSR */ 62 unsigned int gis_shift; 63 int type; /* SAB82532 version */ 64 65 /* Setting configuration bits while the transmitter is active 66 * can cause garbage characters to get emitted by the chip. 67 * Therefore, we cache such writes here and do the real register 68 * write the next time the transmitter becomes idle. 69 */ 70 unsigned int cached_ebrg; 71 unsigned char cached_mode; 72 unsigned char cached_pvr; 73 unsigned char cached_dafo; 74 }; 75 76 /* 77 * This assumes you have a 29.4912 MHz clock for your UART. 78 */ 79 #define SAB_BASE_BAUD ( 29491200 / 16 ) 80 81 static char *sab82532_version[16] = { 82 "V1.0", "V2.0", "V3.2", "V(0x03)", 83 "V(0x04)", "V(0x05)", "V(0x06)", "V(0x07)", 84 "V(0x08)", "V(0x09)", "V(0x0a)", "V(0x0b)", 85 "V(0x0c)", "V(0x0d)", "V(0x0e)", "V(0x0f)" 86 }; 87 88 #define SAB82532_MAX_TEC_TIMEOUT 200000 /* 1 character time (at 50 baud) */ 89 #define SAB82532_MAX_CEC_TIMEOUT 50000 /* 2.5 TX CLKs (at 50 baud) */ 90 91 #define SAB82532_RECV_FIFO_SIZE 32 /* Standard async fifo sizes */ 92 #define SAB82532_XMIT_FIFO_SIZE 32 93 94 static __inline__ void sunsab_tec_wait(struct uart_sunsab_port *up) 95 { 96 int timeout = up->tec_timeout; 97 98 while ((readb(&up->regs->r.star) & SAB82532_STAR_TEC) && --timeout) 99 udelay(1); 100 } 101 102 static __inline__ void sunsab_cec_wait(struct uart_sunsab_port *up) 103 { 104 int timeout = up->cec_timeout; 105 106 while ((readb(&up->regs->r.star) & SAB82532_STAR_CEC) && --timeout) 107 udelay(1); 108 } 109 110 static struct tty_port * 111 receive_chars(struct uart_sunsab_port *up, 112 union sab82532_irq_status *stat) 113 { 114 struct tty_port *port = NULL; 115 unsigned char buf[32]; 116 int saw_console_brk = 0; 117 int free_fifo = 0; 118 int count = 0; 119 int i; 120 121 if (up->port.state != NULL) /* Unopened serial console */ 122 port = &up->port.state->port; 123 124 /* Read number of BYTES (Character + Status) available. */ 125 if (stat->sreg.isr0 & SAB82532_ISR0_RPF) { 126 count = SAB82532_RECV_FIFO_SIZE; 127 free_fifo++; 128 } 129 130 if (stat->sreg.isr0 & SAB82532_ISR0_TCD) { 131 count = readb(&up->regs->r.rbcl) & (SAB82532_RECV_FIFO_SIZE - 1); 132 free_fifo++; 133 } 134 135 /* Issue a FIFO read command in case we where idle. */ 136 if (stat->sreg.isr0 & SAB82532_ISR0_TIME) { 137 sunsab_cec_wait(up); 138 writeb(SAB82532_CMDR_RFRD, &up->regs->w.cmdr); 139 return port; 140 } 141 142 if (stat->sreg.isr0 & SAB82532_ISR0_RFO) 143 free_fifo++; 144 145 /* Read the FIFO. */ 146 for (i = 0; i < count; i++) 147 buf[i] = readb(&up->regs->r.rfifo[i]); 148 149 /* Issue Receive Message Complete command. */ 150 if (free_fifo) { 151 sunsab_cec_wait(up); 152 writeb(SAB82532_CMDR_RMC, &up->regs->w.cmdr); 153 } 154 155 /* Count may be zero for BRK, so we check for it here */ 156 if ((stat->sreg.isr1 & SAB82532_ISR1_BRK) && 157 (up->port.line == up->port.cons->index)) 158 saw_console_brk = 1; 159 160 if (count == 0) { 161 if (unlikely(stat->sreg.isr1 & SAB82532_ISR1_BRK)) { 162 stat->sreg.isr0 &= ~(SAB82532_ISR0_PERR | 163 SAB82532_ISR0_FERR); 164 up->port.icount.brk++; 165 uart_handle_break(&up->port); 166 } 167 } 168 169 for (i = 0; i < count; i++) { 170 unsigned char ch = buf[i], flag; 171 172 flag = TTY_NORMAL; 173 up->port.icount.rx++; 174 175 if (unlikely(stat->sreg.isr0 & (SAB82532_ISR0_PERR | 176 SAB82532_ISR0_FERR | 177 SAB82532_ISR0_RFO)) || 178 unlikely(stat->sreg.isr1 & SAB82532_ISR1_BRK)) { 179 /* 180 * For statistics only 181 */ 182 if (stat->sreg.isr1 & SAB82532_ISR1_BRK) { 183 stat->sreg.isr0 &= ~(SAB82532_ISR0_PERR | 184 SAB82532_ISR0_FERR); 185 up->port.icount.brk++; 186 /* 187 * We do the SysRQ and SAK checking 188 * here because otherwise the break 189 * may get masked by ignore_status_mask 190 * or read_status_mask. 191 */ 192 if (uart_handle_break(&up->port)) 193 continue; 194 } else if (stat->sreg.isr0 & SAB82532_ISR0_PERR) 195 up->port.icount.parity++; 196 else if (stat->sreg.isr0 & SAB82532_ISR0_FERR) 197 up->port.icount.frame++; 198 if (stat->sreg.isr0 & SAB82532_ISR0_RFO) 199 up->port.icount.overrun++; 200 201 /* 202 * Mask off conditions which should be ingored. 203 */ 204 stat->sreg.isr0 &= (up->port.read_status_mask & 0xff); 205 stat->sreg.isr1 &= ((up->port.read_status_mask >> 8) & 0xff); 206 207 if (stat->sreg.isr1 & SAB82532_ISR1_BRK) { 208 flag = TTY_BREAK; 209 } else if (stat->sreg.isr0 & SAB82532_ISR0_PERR) 210 flag = TTY_PARITY; 211 else if (stat->sreg.isr0 & SAB82532_ISR0_FERR) 212 flag = TTY_FRAME; 213 } 214 215 if (uart_handle_sysrq_char(&up->port, ch) || !port) 216 continue; 217 218 if ((stat->sreg.isr0 & (up->port.ignore_status_mask & 0xff)) == 0 && 219 (stat->sreg.isr1 & ((up->port.ignore_status_mask >> 8) & 0xff)) == 0) 220 tty_insert_flip_char(port, ch, flag); 221 if (stat->sreg.isr0 & SAB82532_ISR0_RFO) 222 tty_insert_flip_char(port, 0, TTY_OVERRUN); 223 } 224 225 if (saw_console_brk) 226 sun_do_break(); 227 228 return port; 229 } 230 231 static void sunsab_stop_tx(struct uart_port *); 232 static void sunsab_tx_idle(struct uart_sunsab_port *); 233 234 static void transmit_chars(struct uart_sunsab_port *up, 235 union sab82532_irq_status *stat) 236 { 237 struct circ_buf *xmit = &up->port.state->xmit; 238 int i; 239 240 if (stat->sreg.isr1 & SAB82532_ISR1_ALLS) { 241 up->interrupt_mask1 |= SAB82532_IMR1_ALLS; 242 writeb(up->interrupt_mask1, &up->regs->w.imr1); 243 set_bit(SAB82532_ALLS, &up->irqflags); 244 } 245 246 #if 0 /* bde@nwlink.com says this check causes problems */ 247 if (!(stat->sreg.isr1 & SAB82532_ISR1_XPR)) 248 return; 249 #endif 250 251 if (!(readb(&up->regs->r.star) & SAB82532_STAR_XFW)) 252 return; 253 254 set_bit(SAB82532_XPR, &up->irqflags); 255 sunsab_tx_idle(up); 256 257 if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) { 258 up->interrupt_mask1 |= SAB82532_IMR1_XPR; 259 writeb(up->interrupt_mask1, &up->regs->w.imr1); 260 return; 261 } 262 263 up->interrupt_mask1 &= ~(SAB82532_IMR1_ALLS|SAB82532_IMR1_XPR); 264 writeb(up->interrupt_mask1, &up->regs->w.imr1); 265 clear_bit(SAB82532_ALLS, &up->irqflags); 266 267 /* Stuff 32 bytes into Transmit FIFO. */ 268 clear_bit(SAB82532_XPR, &up->irqflags); 269 for (i = 0; i < up->port.fifosize; i++) { 270 writeb(xmit->buf[xmit->tail], 271 &up->regs->w.xfifo[i]); 272 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 273 up->port.icount.tx++; 274 if (uart_circ_empty(xmit)) 275 break; 276 } 277 278 /* Issue a Transmit Frame command. */ 279 sunsab_cec_wait(up); 280 writeb(SAB82532_CMDR_XF, &up->regs->w.cmdr); 281 282 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 283 uart_write_wakeup(&up->port); 284 285 if (uart_circ_empty(xmit)) 286 sunsab_stop_tx(&up->port); 287 } 288 289 static void check_status(struct uart_sunsab_port *up, 290 union sab82532_irq_status *stat) 291 { 292 if (stat->sreg.isr0 & SAB82532_ISR0_CDSC) 293 uart_handle_dcd_change(&up->port, 294 !(readb(&up->regs->r.vstr) & SAB82532_VSTR_CD)); 295 296 if (stat->sreg.isr1 & SAB82532_ISR1_CSC) 297 uart_handle_cts_change(&up->port, 298 (readb(&up->regs->r.star) & SAB82532_STAR_CTS)); 299 300 if ((readb(&up->regs->r.pvr) & up->pvr_dsr_bit) ^ up->dsr) { 301 up->dsr = (readb(&up->regs->r.pvr) & up->pvr_dsr_bit) ? 0 : 1; 302 up->port.icount.dsr++; 303 } 304 305 wake_up_interruptible(&up->port.state->port.delta_msr_wait); 306 } 307 308 static irqreturn_t sunsab_interrupt(int irq, void *dev_id) 309 { 310 struct uart_sunsab_port *up = dev_id; 311 struct tty_port *port = NULL; 312 union sab82532_irq_status status; 313 unsigned long flags; 314 unsigned char gis; 315 316 spin_lock_irqsave(&up->port.lock, flags); 317 318 status.stat = 0; 319 gis = readb(&up->regs->r.gis) >> up->gis_shift; 320 if (gis & 1) 321 status.sreg.isr0 = readb(&up->regs->r.isr0); 322 if (gis & 2) 323 status.sreg.isr1 = readb(&up->regs->r.isr1); 324 325 if (status.stat) { 326 if ((status.sreg.isr0 & (SAB82532_ISR0_TCD | SAB82532_ISR0_TIME | 327 SAB82532_ISR0_RFO | SAB82532_ISR0_RPF)) || 328 (status.sreg.isr1 & SAB82532_ISR1_BRK)) 329 port = receive_chars(up, &status); 330 if ((status.sreg.isr0 & SAB82532_ISR0_CDSC) || 331 (status.sreg.isr1 & SAB82532_ISR1_CSC)) 332 check_status(up, &status); 333 if (status.sreg.isr1 & (SAB82532_ISR1_ALLS | SAB82532_ISR1_XPR)) 334 transmit_chars(up, &status); 335 } 336 337 spin_unlock_irqrestore(&up->port.lock, flags); 338 339 if (port) 340 tty_flip_buffer_push(port); 341 342 return IRQ_HANDLED; 343 } 344 345 /* port->lock is not held. */ 346 static unsigned int sunsab_tx_empty(struct uart_port *port) 347 { 348 struct uart_sunsab_port *up = 349 container_of(port, struct uart_sunsab_port, port); 350 int ret; 351 352 /* Do not need a lock for a state test like this. */ 353 if (test_bit(SAB82532_ALLS, &up->irqflags)) 354 ret = TIOCSER_TEMT; 355 else 356 ret = 0; 357 358 return ret; 359 } 360 361 /* port->lock held by caller. */ 362 static void sunsab_set_mctrl(struct uart_port *port, unsigned int mctrl) 363 { 364 struct uart_sunsab_port *up = 365 container_of(port, struct uart_sunsab_port, port); 366 367 if (mctrl & TIOCM_RTS) { 368 up->cached_mode &= ~SAB82532_MODE_FRTS; 369 up->cached_mode |= SAB82532_MODE_RTS; 370 } else { 371 up->cached_mode |= (SAB82532_MODE_FRTS | 372 SAB82532_MODE_RTS); 373 } 374 if (mctrl & TIOCM_DTR) { 375 up->cached_pvr &= ~(up->pvr_dtr_bit); 376 } else { 377 up->cached_pvr |= up->pvr_dtr_bit; 378 } 379 380 set_bit(SAB82532_REGS_PENDING, &up->irqflags); 381 if (test_bit(SAB82532_XPR, &up->irqflags)) 382 sunsab_tx_idle(up); 383 } 384 385 /* port->lock is held by caller and interrupts are disabled. */ 386 static unsigned int sunsab_get_mctrl(struct uart_port *port) 387 { 388 struct uart_sunsab_port *up = 389 container_of(port, struct uart_sunsab_port, port); 390 unsigned char val; 391 unsigned int result; 392 393 result = 0; 394 395 val = readb(&up->regs->r.pvr); 396 result |= (val & up->pvr_dsr_bit) ? 0 : TIOCM_DSR; 397 398 val = readb(&up->regs->r.vstr); 399 result |= (val & SAB82532_VSTR_CD) ? 0 : TIOCM_CAR; 400 401 val = readb(&up->regs->r.star); 402 result |= (val & SAB82532_STAR_CTS) ? TIOCM_CTS : 0; 403 404 return result; 405 } 406 407 /* port->lock held by caller. */ 408 static void sunsab_stop_tx(struct uart_port *port) 409 { 410 struct uart_sunsab_port *up = 411 container_of(port, struct uart_sunsab_port, port); 412 413 up->interrupt_mask1 |= SAB82532_IMR1_XPR; 414 writeb(up->interrupt_mask1, &up->regs->w.imr1); 415 } 416 417 /* port->lock held by caller. */ 418 static void sunsab_tx_idle(struct uart_sunsab_port *up) 419 { 420 if (test_bit(SAB82532_REGS_PENDING, &up->irqflags)) { 421 u8 tmp; 422 423 clear_bit(SAB82532_REGS_PENDING, &up->irqflags); 424 writeb(up->cached_mode, &up->regs->rw.mode); 425 writeb(up->cached_pvr, &up->regs->rw.pvr); 426 writeb(up->cached_dafo, &up->regs->w.dafo); 427 428 writeb(up->cached_ebrg & 0xff, &up->regs->w.bgr); 429 tmp = readb(&up->regs->rw.ccr2); 430 tmp &= ~0xc0; 431 tmp |= (up->cached_ebrg >> 2) & 0xc0; 432 writeb(tmp, &up->regs->rw.ccr2); 433 } 434 } 435 436 /* port->lock held by caller. */ 437 static void sunsab_start_tx(struct uart_port *port) 438 { 439 struct uart_sunsab_port *up = 440 container_of(port, struct uart_sunsab_port, port); 441 struct circ_buf *xmit = &up->port.state->xmit; 442 int i; 443 444 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) 445 return; 446 447 up->interrupt_mask1 &= ~(SAB82532_IMR1_ALLS|SAB82532_IMR1_XPR); 448 writeb(up->interrupt_mask1, &up->regs->w.imr1); 449 450 if (!test_bit(SAB82532_XPR, &up->irqflags)) 451 return; 452 453 clear_bit(SAB82532_ALLS, &up->irqflags); 454 clear_bit(SAB82532_XPR, &up->irqflags); 455 456 for (i = 0; i < up->port.fifosize; i++) { 457 writeb(xmit->buf[xmit->tail], 458 &up->regs->w.xfifo[i]); 459 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 460 up->port.icount.tx++; 461 if (uart_circ_empty(xmit)) 462 break; 463 } 464 465 /* Issue a Transmit Frame command. */ 466 sunsab_cec_wait(up); 467 writeb(SAB82532_CMDR_XF, &up->regs->w.cmdr); 468 } 469 470 /* port->lock is not held. */ 471 static void sunsab_send_xchar(struct uart_port *port, char ch) 472 { 473 struct uart_sunsab_port *up = 474 container_of(port, struct uart_sunsab_port, port); 475 unsigned long flags; 476 477 if (ch == __DISABLED_CHAR) 478 return; 479 480 spin_lock_irqsave(&up->port.lock, flags); 481 482 sunsab_tec_wait(up); 483 writeb(ch, &up->regs->w.tic); 484 485 spin_unlock_irqrestore(&up->port.lock, flags); 486 } 487 488 /* port->lock held by caller. */ 489 static void sunsab_stop_rx(struct uart_port *port) 490 { 491 struct uart_sunsab_port *up = 492 container_of(port, struct uart_sunsab_port, port); 493 494 up->interrupt_mask0 |= SAB82532_IMR0_TCD; 495 writeb(up->interrupt_mask1, &up->regs->w.imr0); 496 } 497 498 /* port->lock is not held. */ 499 static void sunsab_break_ctl(struct uart_port *port, int break_state) 500 { 501 struct uart_sunsab_port *up = 502 container_of(port, struct uart_sunsab_port, port); 503 unsigned long flags; 504 unsigned char val; 505 506 spin_lock_irqsave(&up->port.lock, flags); 507 508 val = up->cached_dafo; 509 if (break_state) 510 val |= SAB82532_DAFO_XBRK; 511 else 512 val &= ~SAB82532_DAFO_XBRK; 513 up->cached_dafo = val; 514 515 set_bit(SAB82532_REGS_PENDING, &up->irqflags); 516 if (test_bit(SAB82532_XPR, &up->irqflags)) 517 sunsab_tx_idle(up); 518 519 spin_unlock_irqrestore(&up->port.lock, flags); 520 } 521 522 /* port->lock is not held. */ 523 static int sunsab_startup(struct uart_port *port) 524 { 525 struct uart_sunsab_port *up = 526 container_of(port, struct uart_sunsab_port, port); 527 unsigned long flags; 528 unsigned char tmp; 529 int err = request_irq(up->port.irq, sunsab_interrupt, 530 IRQF_SHARED, "sab", up); 531 if (err) 532 return err; 533 534 spin_lock_irqsave(&up->port.lock, flags); 535 536 /* 537 * Wait for any commands or immediate characters 538 */ 539 sunsab_cec_wait(up); 540 sunsab_tec_wait(up); 541 542 /* 543 * Clear the FIFO buffers. 544 */ 545 writeb(SAB82532_CMDR_RRES, &up->regs->w.cmdr); 546 sunsab_cec_wait(up); 547 writeb(SAB82532_CMDR_XRES, &up->regs->w.cmdr); 548 549 /* 550 * Clear the interrupt registers. 551 */ 552 (void) readb(&up->regs->r.isr0); 553 (void) readb(&up->regs->r.isr1); 554 555 /* 556 * Now, initialize the UART 557 */ 558 writeb(0, &up->regs->w.ccr0); /* power-down */ 559 writeb(SAB82532_CCR0_MCE | SAB82532_CCR0_SC_NRZ | 560 SAB82532_CCR0_SM_ASYNC, &up->regs->w.ccr0); 561 writeb(SAB82532_CCR1_ODS | SAB82532_CCR1_BCR | 7, &up->regs->w.ccr1); 562 writeb(SAB82532_CCR2_BDF | SAB82532_CCR2_SSEL | 563 SAB82532_CCR2_TOE, &up->regs->w.ccr2); 564 writeb(0, &up->regs->w.ccr3); 565 writeb(SAB82532_CCR4_MCK4 | SAB82532_CCR4_EBRG, &up->regs->w.ccr4); 566 up->cached_mode = (SAB82532_MODE_RTS | SAB82532_MODE_FCTS | 567 SAB82532_MODE_RAC); 568 writeb(up->cached_mode, &up->regs->w.mode); 569 writeb(SAB82532_RFC_DPS|SAB82532_RFC_RFTH_32, &up->regs->w.rfc); 570 571 tmp = readb(&up->regs->rw.ccr0); 572 tmp |= SAB82532_CCR0_PU; /* power-up */ 573 writeb(tmp, &up->regs->rw.ccr0); 574 575 /* 576 * Finally, enable interrupts 577 */ 578 up->interrupt_mask0 = (SAB82532_IMR0_PERR | SAB82532_IMR0_FERR | 579 SAB82532_IMR0_PLLA); 580 writeb(up->interrupt_mask0, &up->regs->w.imr0); 581 up->interrupt_mask1 = (SAB82532_IMR1_BRKT | SAB82532_IMR1_ALLS | 582 SAB82532_IMR1_XOFF | SAB82532_IMR1_TIN | 583 SAB82532_IMR1_CSC | SAB82532_IMR1_XON | 584 SAB82532_IMR1_XPR); 585 writeb(up->interrupt_mask1, &up->regs->w.imr1); 586 set_bit(SAB82532_ALLS, &up->irqflags); 587 set_bit(SAB82532_XPR, &up->irqflags); 588 589 spin_unlock_irqrestore(&up->port.lock, flags); 590 591 return 0; 592 } 593 594 /* port->lock is not held. */ 595 static void sunsab_shutdown(struct uart_port *port) 596 { 597 struct uart_sunsab_port *up = 598 container_of(port, struct uart_sunsab_port, port); 599 unsigned long flags; 600 601 spin_lock_irqsave(&up->port.lock, flags); 602 603 /* Disable Interrupts */ 604 up->interrupt_mask0 = 0xff; 605 writeb(up->interrupt_mask0, &up->regs->w.imr0); 606 up->interrupt_mask1 = 0xff; 607 writeb(up->interrupt_mask1, &up->regs->w.imr1); 608 609 /* Disable break condition */ 610 up->cached_dafo = readb(&up->regs->rw.dafo); 611 up->cached_dafo &= ~SAB82532_DAFO_XBRK; 612 writeb(up->cached_dafo, &up->regs->rw.dafo); 613 614 /* Disable Receiver */ 615 up->cached_mode &= ~SAB82532_MODE_RAC; 616 writeb(up->cached_mode, &up->regs->rw.mode); 617 618 /* 619 * XXX FIXME 620 * 621 * If the chip is powered down here the system hangs/crashes during 622 * reboot or shutdown. This needs to be investigated further, 623 * similar behaviour occurs in 2.4 when the driver is configured 624 * as a module only. One hint may be that data is sometimes 625 * transmitted at 9600 baud during shutdown (regardless of the 626 * speed the chip was configured for when the port was open). 627 */ 628 #if 0 629 /* Power Down */ 630 tmp = readb(&up->regs->rw.ccr0); 631 tmp &= ~SAB82532_CCR0_PU; 632 writeb(tmp, &up->regs->rw.ccr0); 633 #endif 634 635 spin_unlock_irqrestore(&up->port.lock, flags); 636 free_irq(up->port.irq, up); 637 } 638 639 /* 640 * This is used to figure out the divisor speeds. 641 * 642 * The formula is: Baud = SAB_BASE_BAUD / ((N + 1) * (1 << M)), 643 * 644 * with 0 <= N < 64 and 0 <= M < 16 645 */ 646 647 static void calc_ebrg(int baud, int *n_ret, int *m_ret) 648 { 649 int n, m; 650 651 if (baud == 0) { 652 *n_ret = 0; 653 *m_ret = 0; 654 return; 655 } 656 657 /* 658 * We scale numbers by 10 so that we get better accuracy 659 * without having to use floating point. Here we increment m 660 * until n is within the valid range. 661 */ 662 n = (SAB_BASE_BAUD * 10) / baud; 663 m = 0; 664 while (n >= 640) { 665 n = n / 2; 666 m++; 667 } 668 n = (n+5) / 10; 669 /* 670 * We try very hard to avoid speeds with M == 0 since they may 671 * not work correctly for XTAL frequences above 10 MHz. 672 */ 673 if ((m == 0) && ((n & 1) == 0)) { 674 n = n / 2; 675 m++; 676 } 677 *n_ret = n - 1; 678 *m_ret = m; 679 } 680 681 /* Internal routine, port->lock is held and local interrupts are disabled. */ 682 static void sunsab_convert_to_sab(struct uart_sunsab_port *up, unsigned int cflag, 683 unsigned int iflag, unsigned int baud, 684 unsigned int quot) 685 { 686 unsigned char dafo; 687 int bits, n, m; 688 689 /* Byte size and parity */ 690 switch (cflag & CSIZE) { 691 case CS5: dafo = SAB82532_DAFO_CHL5; bits = 7; break; 692 case CS6: dafo = SAB82532_DAFO_CHL6; bits = 8; break; 693 case CS7: dafo = SAB82532_DAFO_CHL7; bits = 9; break; 694 case CS8: dafo = SAB82532_DAFO_CHL8; bits = 10; break; 695 /* Never happens, but GCC is too dumb to figure it out */ 696 default: dafo = SAB82532_DAFO_CHL5; bits = 7; break; 697 } 698 699 if (cflag & CSTOPB) { 700 dafo |= SAB82532_DAFO_STOP; 701 bits++; 702 } 703 704 if (cflag & PARENB) { 705 dafo |= SAB82532_DAFO_PARE; 706 bits++; 707 } 708 709 if (cflag & PARODD) { 710 dafo |= SAB82532_DAFO_PAR_ODD; 711 } else { 712 dafo |= SAB82532_DAFO_PAR_EVEN; 713 } 714 up->cached_dafo = dafo; 715 716 calc_ebrg(baud, &n, &m); 717 718 up->cached_ebrg = n | (m << 6); 719 720 up->tec_timeout = (10 * 1000000) / baud; 721 up->cec_timeout = up->tec_timeout >> 2; 722 723 /* CTS flow control flags */ 724 /* We encode read_status_mask and ignore_status_mask like so: 725 * 726 * --------------------- 727 * | ... | ISR1 | ISR0 | 728 * --------------------- 729 * .. 15 8 7 0 730 */ 731 732 up->port.read_status_mask = (SAB82532_ISR0_TCD | SAB82532_ISR0_TIME | 733 SAB82532_ISR0_RFO | SAB82532_ISR0_RPF | 734 SAB82532_ISR0_CDSC); 735 up->port.read_status_mask |= (SAB82532_ISR1_CSC | 736 SAB82532_ISR1_ALLS | 737 SAB82532_ISR1_XPR) << 8; 738 if (iflag & INPCK) 739 up->port.read_status_mask |= (SAB82532_ISR0_PERR | 740 SAB82532_ISR0_FERR); 741 if (iflag & (IGNBRK | BRKINT | PARMRK)) 742 up->port.read_status_mask |= (SAB82532_ISR1_BRK << 8); 743 744 /* 745 * Characteres to ignore 746 */ 747 up->port.ignore_status_mask = 0; 748 if (iflag & IGNPAR) 749 up->port.ignore_status_mask |= (SAB82532_ISR0_PERR | 750 SAB82532_ISR0_FERR); 751 if (iflag & IGNBRK) { 752 up->port.ignore_status_mask |= (SAB82532_ISR1_BRK << 8); 753 /* 754 * If we're ignoring parity and break indicators, 755 * ignore overruns too (for real raw support). 756 */ 757 if (iflag & IGNPAR) 758 up->port.ignore_status_mask |= SAB82532_ISR0_RFO; 759 } 760 761 /* 762 * ignore all characters if CREAD is not set 763 */ 764 if ((cflag & CREAD) == 0) 765 up->port.ignore_status_mask |= (SAB82532_ISR0_RPF | 766 SAB82532_ISR0_TCD); 767 768 uart_update_timeout(&up->port, cflag, 769 (up->port.uartclk / (16 * quot))); 770 771 /* Now schedule a register update when the chip's 772 * transmitter is idle. 773 */ 774 up->cached_mode |= SAB82532_MODE_RAC; 775 set_bit(SAB82532_REGS_PENDING, &up->irqflags); 776 if (test_bit(SAB82532_XPR, &up->irqflags)) 777 sunsab_tx_idle(up); 778 } 779 780 /* port->lock is not held. */ 781 static void sunsab_set_termios(struct uart_port *port, struct ktermios *termios, 782 struct ktermios *old) 783 { 784 struct uart_sunsab_port *up = 785 container_of(port, struct uart_sunsab_port, port); 786 unsigned long flags; 787 unsigned int baud = uart_get_baud_rate(port, termios, old, 0, 4000000); 788 unsigned int quot = uart_get_divisor(port, baud); 789 790 spin_lock_irqsave(&up->port.lock, flags); 791 sunsab_convert_to_sab(up, termios->c_cflag, termios->c_iflag, baud, quot); 792 spin_unlock_irqrestore(&up->port.lock, flags); 793 } 794 795 static const char *sunsab_type(struct uart_port *port) 796 { 797 struct uart_sunsab_port *up = (void *)port; 798 static char buf[36]; 799 800 sprintf(buf, "SAB82532 %s", sab82532_version[up->type]); 801 return buf; 802 } 803 804 static void sunsab_release_port(struct uart_port *port) 805 { 806 } 807 808 static int sunsab_request_port(struct uart_port *port) 809 { 810 return 0; 811 } 812 813 static void sunsab_config_port(struct uart_port *port, int flags) 814 { 815 } 816 817 static int sunsab_verify_port(struct uart_port *port, struct serial_struct *ser) 818 { 819 return -EINVAL; 820 } 821 822 static struct uart_ops sunsab_pops = { 823 .tx_empty = sunsab_tx_empty, 824 .set_mctrl = sunsab_set_mctrl, 825 .get_mctrl = sunsab_get_mctrl, 826 .stop_tx = sunsab_stop_tx, 827 .start_tx = sunsab_start_tx, 828 .send_xchar = sunsab_send_xchar, 829 .stop_rx = sunsab_stop_rx, 830 .break_ctl = sunsab_break_ctl, 831 .startup = sunsab_startup, 832 .shutdown = sunsab_shutdown, 833 .set_termios = sunsab_set_termios, 834 .type = sunsab_type, 835 .release_port = sunsab_release_port, 836 .request_port = sunsab_request_port, 837 .config_port = sunsab_config_port, 838 .verify_port = sunsab_verify_port, 839 }; 840 841 static struct uart_driver sunsab_reg = { 842 .owner = THIS_MODULE, 843 .driver_name = "sunsab", 844 .dev_name = "ttyS", 845 .major = TTY_MAJOR, 846 }; 847 848 static struct uart_sunsab_port *sunsab_ports; 849 850 #ifdef CONFIG_SERIAL_SUNSAB_CONSOLE 851 852 static void sunsab_console_putchar(struct uart_port *port, int c) 853 { 854 struct uart_sunsab_port *up = 855 container_of(port, struct uart_sunsab_port, port); 856 857 sunsab_tec_wait(up); 858 writeb(c, &up->regs->w.tic); 859 } 860 861 static void sunsab_console_write(struct console *con, const char *s, unsigned n) 862 { 863 struct uart_sunsab_port *up = &sunsab_ports[con->index]; 864 unsigned long flags; 865 int locked = 1; 866 867 if (up->port.sysrq || oops_in_progress) 868 locked = spin_trylock_irqsave(&up->port.lock, flags); 869 else 870 spin_lock_irqsave(&up->port.lock, flags); 871 872 uart_console_write(&up->port, s, n, sunsab_console_putchar); 873 sunsab_tec_wait(up); 874 875 if (locked) 876 spin_unlock_irqrestore(&up->port.lock, flags); 877 } 878 879 static int sunsab_console_setup(struct console *con, char *options) 880 { 881 struct uart_sunsab_port *up = &sunsab_ports[con->index]; 882 unsigned long flags; 883 unsigned int baud, quot; 884 885 /* 886 * The console framework calls us for each and every port 887 * registered. Defer the console setup until the requested 888 * port has been properly discovered. A bit of a hack, 889 * though... 890 */ 891 if (up->port.type != PORT_SUNSAB) 892 return -1; 893 894 printk("Console: ttyS%d (SAB82532)\n", 895 (sunsab_reg.minor - 64) + con->index); 896 897 sunserial_console_termios(con, up->port.dev->of_node); 898 899 switch (con->cflag & CBAUD) { 900 case B150: baud = 150; break; 901 case B300: baud = 300; break; 902 case B600: baud = 600; break; 903 case B1200: baud = 1200; break; 904 case B2400: baud = 2400; break; 905 case B4800: baud = 4800; break; 906 default: case B9600: baud = 9600; break; 907 case B19200: baud = 19200; break; 908 case B38400: baud = 38400; break; 909 case B57600: baud = 57600; break; 910 case B115200: baud = 115200; break; 911 case B230400: baud = 230400; break; 912 case B460800: baud = 460800; break; 913 } 914 915 /* 916 * Temporary fix. 917 */ 918 spin_lock_init(&up->port.lock); 919 920 /* 921 * Initialize the hardware 922 */ 923 sunsab_startup(&up->port); 924 925 spin_lock_irqsave(&up->port.lock, flags); 926 927 /* 928 * Finally, enable interrupts 929 */ 930 up->interrupt_mask0 = SAB82532_IMR0_PERR | SAB82532_IMR0_FERR | 931 SAB82532_IMR0_PLLA | SAB82532_IMR0_CDSC; 932 writeb(up->interrupt_mask0, &up->regs->w.imr0); 933 up->interrupt_mask1 = SAB82532_IMR1_BRKT | SAB82532_IMR1_ALLS | 934 SAB82532_IMR1_XOFF | SAB82532_IMR1_TIN | 935 SAB82532_IMR1_CSC | SAB82532_IMR1_XON | 936 SAB82532_IMR1_XPR; 937 writeb(up->interrupt_mask1, &up->regs->w.imr1); 938 939 quot = uart_get_divisor(&up->port, baud); 940 sunsab_convert_to_sab(up, con->cflag, 0, baud, quot); 941 sunsab_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS); 942 943 spin_unlock_irqrestore(&up->port.lock, flags); 944 945 return 0; 946 } 947 948 static struct console sunsab_console = { 949 .name = "ttyS", 950 .write = sunsab_console_write, 951 .device = uart_console_device, 952 .setup = sunsab_console_setup, 953 .flags = CON_PRINTBUFFER, 954 .index = -1, 955 .data = &sunsab_reg, 956 }; 957 958 static inline struct console *SUNSAB_CONSOLE(void) 959 { 960 return &sunsab_console; 961 } 962 #else 963 #define SUNSAB_CONSOLE() (NULL) 964 #define sunsab_console_init() do { } while (0) 965 #endif 966 967 static int sunsab_init_one(struct uart_sunsab_port *up, 968 struct platform_device *op, 969 unsigned long offset, 970 int line) 971 { 972 up->port.line = line; 973 up->port.dev = &op->dev; 974 975 up->port.mapbase = op->resource[0].start + offset; 976 up->port.membase = of_ioremap(&op->resource[0], offset, 977 sizeof(union sab82532_async_regs), 978 "sab"); 979 if (!up->port.membase) 980 return -ENOMEM; 981 up->regs = (union sab82532_async_regs __iomem *) up->port.membase; 982 983 up->port.irq = op->archdata.irqs[0]; 984 985 up->port.fifosize = SAB82532_XMIT_FIFO_SIZE; 986 up->port.iotype = UPIO_MEM; 987 988 writeb(SAB82532_IPC_IC_ACT_LOW, &up->regs->w.ipc); 989 990 up->port.ops = &sunsab_pops; 991 up->port.type = PORT_SUNSAB; 992 up->port.uartclk = SAB_BASE_BAUD; 993 994 up->type = readb(&up->regs->r.vstr) & 0x0f; 995 writeb(~((1 << 1) | (1 << 2) | (1 << 4)), &up->regs->w.pcr); 996 writeb(0xff, &up->regs->w.pim); 997 if ((up->port.line & 0x1) == 0) { 998 up->pvr_dsr_bit = (1 << 0); 999 up->pvr_dtr_bit = (1 << 1); 1000 up->gis_shift = 2; 1001 } else { 1002 up->pvr_dsr_bit = (1 << 3); 1003 up->pvr_dtr_bit = (1 << 2); 1004 up->gis_shift = 0; 1005 } 1006 up->cached_pvr = (1 << 1) | (1 << 2) | (1 << 4); 1007 writeb(up->cached_pvr, &up->regs->w.pvr); 1008 up->cached_mode = readb(&up->regs->rw.mode); 1009 up->cached_mode |= SAB82532_MODE_FRTS; 1010 writeb(up->cached_mode, &up->regs->rw.mode); 1011 up->cached_mode |= SAB82532_MODE_RTS; 1012 writeb(up->cached_mode, &up->regs->rw.mode); 1013 1014 up->tec_timeout = SAB82532_MAX_TEC_TIMEOUT; 1015 up->cec_timeout = SAB82532_MAX_CEC_TIMEOUT; 1016 1017 return 0; 1018 } 1019 1020 static int sab_probe(struct platform_device *op) 1021 { 1022 static int inst; 1023 struct uart_sunsab_port *up; 1024 int err; 1025 1026 up = &sunsab_ports[inst * 2]; 1027 1028 err = sunsab_init_one(&up[0], op, 1029 0, 1030 (inst * 2) + 0); 1031 if (err) 1032 goto out; 1033 1034 err = sunsab_init_one(&up[1], op, 1035 sizeof(union sab82532_async_regs), 1036 (inst * 2) + 1); 1037 if (err) 1038 goto out1; 1039 1040 sunserial_console_match(SUNSAB_CONSOLE(), op->dev.of_node, 1041 &sunsab_reg, up[0].port.line, 1042 false); 1043 1044 sunserial_console_match(SUNSAB_CONSOLE(), op->dev.of_node, 1045 &sunsab_reg, up[1].port.line, 1046 false); 1047 1048 err = uart_add_one_port(&sunsab_reg, &up[0].port); 1049 if (err) 1050 goto out2; 1051 1052 err = uart_add_one_port(&sunsab_reg, &up[1].port); 1053 if (err) 1054 goto out3; 1055 1056 platform_set_drvdata(op, &up[0]); 1057 1058 inst++; 1059 1060 return 0; 1061 1062 out3: 1063 uart_remove_one_port(&sunsab_reg, &up[0].port); 1064 out2: 1065 of_iounmap(&op->resource[0], 1066 up[1].port.membase, 1067 sizeof(union sab82532_async_regs)); 1068 out1: 1069 of_iounmap(&op->resource[0], 1070 up[0].port.membase, 1071 sizeof(union sab82532_async_regs)); 1072 out: 1073 return err; 1074 } 1075 1076 static int sab_remove(struct platform_device *op) 1077 { 1078 struct uart_sunsab_port *up = platform_get_drvdata(op); 1079 1080 uart_remove_one_port(&sunsab_reg, &up[1].port); 1081 uart_remove_one_port(&sunsab_reg, &up[0].port); 1082 of_iounmap(&op->resource[0], 1083 up[1].port.membase, 1084 sizeof(union sab82532_async_regs)); 1085 of_iounmap(&op->resource[0], 1086 up[0].port.membase, 1087 sizeof(union sab82532_async_regs)); 1088 1089 return 0; 1090 } 1091 1092 static const struct of_device_id sab_match[] = { 1093 { 1094 .name = "se", 1095 }, 1096 { 1097 .name = "serial", 1098 .compatible = "sab82532", 1099 }, 1100 {}, 1101 }; 1102 MODULE_DEVICE_TABLE(of, sab_match); 1103 1104 static struct platform_driver sab_driver = { 1105 .driver = { 1106 .name = "sab", 1107 .of_match_table = sab_match, 1108 }, 1109 .probe = sab_probe, 1110 .remove = sab_remove, 1111 }; 1112 1113 static int __init sunsab_init(void) 1114 { 1115 struct device_node *dp; 1116 int err; 1117 int num_channels = 0; 1118 1119 for_each_node_by_name(dp, "se") 1120 num_channels += 2; 1121 for_each_node_by_name(dp, "serial") { 1122 if (of_device_is_compatible(dp, "sab82532")) 1123 num_channels += 2; 1124 } 1125 1126 if (num_channels) { 1127 sunsab_ports = kzalloc(sizeof(struct uart_sunsab_port) * 1128 num_channels, GFP_KERNEL); 1129 if (!sunsab_ports) 1130 return -ENOMEM; 1131 1132 err = sunserial_register_minors(&sunsab_reg, num_channels); 1133 if (err) { 1134 kfree(sunsab_ports); 1135 sunsab_ports = NULL; 1136 1137 return err; 1138 } 1139 } 1140 1141 return platform_driver_register(&sab_driver); 1142 } 1143 1144 static void __exit sunsab_exit(void) 1145 { 1146 platform_driver_unregister(&sab_driver); 1147 if (sunsab_reg.nr) { 1148 sunserial_unregister_minors(&sunsab_reg, sunsab_reg.nr); 1149 } 1150 1151 kfree(sunsab_ports); 1152 sunsab_ports = NULL; 1153 } 1154 1155 module_init(sunsab_init); 1156 module_exit(sunsab_exit); 1157 1158 MODULE_AUTHOR("Eddie C. Dost and David S. Miller"); 1159 MODULE_DESCRIPTION("Sun SAB82532 serial port driver"); 1160 MODULE_LICENSE("GPL"); 1161