1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Driver core for serial ports 4 * 5 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. 6 * 7 * Copyright 1999 ARM Limited 8 * Copyright (C) 2000-2001 Deep Blue Solutions Ltd. 9 */ 10 #include <linux/module.h> 11 #include <linux/tty.h> 12 #include <linux/tty_flip.h> 13 #include <linux/slab.h> 14 #include <linux/sched/signal.h> 15 #include <linux/init.h> 16 #include <linux/console.h> 17 #include <linux/gpio/consumer.h> 18 #include <linux/kernel.h> 19 #include <linux/of.h> 20 #include <linux/pm_runtime.h> 21 #include <linux/proc_fs.h> 22 #include <linux/seq_file.h> 23 #include <linux/device.h> 24 #include <linux/serial.h> /* for serial_state and serial_icounter_struct */ 25 #include <linux/serial_core.h> 26 #include <linux/sysrq.h> 27 #include <linux/delay.h> 28 #include <linux/mutex.h> 29 #include <linux/math64.h> 30 #include <linux/security.h> 31 32 #include <linux/irq.h> 33 #include <linux/uaccess.h> 34 35 #include "serial_base.h" 36 37 /* 38 * This is used to lock changes in serial line configuration. 39 */ 40 static DEFINE_MUTEX(port_mutex); 41 42 /* 43 * lockdep: port->lock is initialized in two places, but we 44 * want only one lock-class: 45 */ 46 static struct lock_class_key port_lock_key; 47 48 #define HIGH_BITS_OFFSET ((sizeof(long)-sizeof(int))*8) 49 50 /* 51 * Max time with active RTS before/after data is sent. 52 */ 53 #define RS485_MAX_RTS_DELAY 100 /* msecs */ 54 55 static void uart_change_pm(struct uart_state *state, 56 enum uart_pm_state pm_state); 57 58 static void uart_port_shutdown(struct tty_port *port); 59 60 static int uart_dcd_enabled(struct uart_port *uport) 61 { 62 return !!(uport->status & UPSTAT_DCD_ENABLE); 63 } 64 65 static inline struct uart_port *uart_port_ref(struct uart_state *state) 66 { 67 if (atomic_add_unless(&state->refcount, 1, 0)) 68 return state->uart_port; 69 return NULL; 70 } 71 72 static inline void uart_port_deref(struct uart_port *uport) 73 { 74 if (atomic_dec_and_test(&uport->state->refcount)) 75 wake_up(&uport->state->remove_wait); 76 } 77 78 #define uart_port_lock(state, flags) \ 79 ({ \ 80 struct uart_port *__uport = uart_port_ref(state); \ 81 if (__uport) \ 82 uart_port_lock_irqsave(__uport, &flags); \ 83 __uport; \ 84 }) 85 86 #define uart_port_unlock(uport, flags) \ 87 ({ \ 88 struct uart_port *__uport = uport; \ 89 if (__uport) { \ 90 uart_port_unlock_irqrestore(__uport, flags); \ 91 uart_port_deref(__uport); \ 92 } \ 93 }) 94 95 static inline struct uart_port *uart_port_check(struct uart_state *state) 96 { 97 lockdep_assert_held(&state->port.mutex); 98 return state->uart_port; 99 } 100 101 /** 102 * uart_write_wakeup - schedule write processing 103 * @port: port to be processed 104 * 105 * This routine is used by the interrupt handler to schedule processing in the 106 * software interrupt portion of the driver. A driver is expected to call this 107 * function when the number of characters in the transmit buffer have dropped 108 * below a threshold. 109 * 110 * Locking: @port->lock should be held 111 */ 112 void uart_write_wakeup(struct uart_port *port) 113 { 114 struct uart_state *state = port->state; 115 /* 116 * This means you called this function _after_ the port was 117 * closed. No cookie for you. 118 */ 119 BUG_ON(!state); 120 tty_port_tty_wakeup(&state->port); 121 } 122 EXPORT_SYMBOL(uart_write_wakeup); 123 124 static void uart_stop(struct tty_struct *tty) 125 { 126 struct uart_state *state = tty->driver_data; 127 struct uart_port *port; 128 unsigned long flags; 129 130 port = uart_port_lock(state, flags); 131 if (port) 132 port->ops->stop_tx(port); 133 uart_port_unlock(port, flags); 134 } 135 136 static void __uart_start(struct uart_state *state) 137 { 138 struct uart_port *port = state->uart_port; 139 struct serial_port_device *port_dev; 140 int err; 141 142 if (!port || port->flags & UPF_DEAD || uart_tx_stopped(port)) 143 return; 144 145 port_dev = port->port_dev; 146 147 /* Increment the runtime PM usage count for the active check below */ 148 err = pm_runtime_get(&port_dev->dev); 149 if (err < 0 && err != -EINPROGRESS) { 150 pm_runtime_put_noidle(&port_dev->dev); 151 return; 152 } 153 154 /* 155 * Start TX if enabled, and kick runtime PM. If the device is not 156 * enabled, serial_port_runtime_resume() calls start_tx() again 157 * after enabling the device. 158 */ 159 if (!pm_runtime_enabled(port->dev) || pm_runtime_active(&port_dev->dev)) 160 port->ops->start_tx(port); 161 pm_runtime_mark_last_busy(&port_dev->dev); 162 pm_runtime_put_autosuspend(&port_dev->dev); 163 } 164 165 static void uart_start(struct tty_struct *tty) 166 { 167 struct uart_state *state = tty->driver_data; 168 struct uart_port *port; 169 unsigned long flags; 170 171 port = uart_port_lock(state, flags); 172 __uart_start(state); 173 uart_port_unlock(port, flags); 174 } 175 176 static void 177 uart_update_mctrl(struct uart_port *port, unsigned int set, unsigned int clear) 178 { 179 unsigned long flags; 180 unsigned int old; 181 182 uart_port_lock_irqsave(port, &flags); 183 old = port->mctrl; 184 port->mctrl = (old & ~clear) | set; 185 if (old != port->mctrl && !(port->rs485.flags & SER_RS485_ENABLED)) 186 port->ops->set_mctrl(port, port->mctrl); 187 uart_port_unlock_irqrestore(port, flags); 188 } 189 190 #define uart_set_mctrl(port, set) uart_update_mctrl(port, set, 0) 191 #define uart_clear_mctrl(port, clear) uart_update_mctrl(port, 0, clear) 192 193 static void uart_port_dtr_rts(struct uart_port *uport, bool active) 194 { 195 if (active) 196 uart_set_mctrl(uport, TIOCM_DTR | TIOCM_RTS); 197 else 198 uart_clear_mctrl(uport, TIOCM_DTR | TIOCM_RTS); 199 } 200 201 /* Caller holds port mutex */ 202 static void uart_change_line_settings(struct tty_struct *tty, struct uart_state *state, 203 const struct ktermios *old_termios) 204 { 205 struct uart_port *uport = uart_port_check(state); 206 struct ktermios *termios; 207 bool old_hw_stopped; 208 209 /* 210 * If we have no tty, termios, or the port does not exist, 211 * then we can't set the parameters for this port. 212 */ 213 if (!tty || uport->type == PORT_UNKNOWN) 214 return; 215 216 termios = &tty->termios; 217 uport->ops->set_termios(uport, termios, old_termios); 218 219 /* 220 * Set modem status enables based on termios cflag 221 */ 222 uart_port_lock_irq(uport); 223 if (termios->c_cflag & CRTSCTS) 224 uport->status |= UPSTAT_CTS_ENABLE; 225 else 226 uport->status &= ~UPSTAT_CTS_ENABLE; 227 228 if (termios->c_cflag & CLOCAL) 229 uport->status &= ~UPSTAT_DCD_ENABLE; 230 else 231 uport->status |= UPSTAT_DCD_ENABLE; 232 233 /* reset sw-assisted CTS flow control based on (possibly) new mode */ 234 old_hw_stopped = uport->hw_stopped; 235 uport->hw_stopped = uart_softcts_mode(uport) && 236 !(uport->ops->get_mctrl(uport) & TIOCM_CTS); 237 if (uport->hw_stopped != old_hw_stopped) { 238 if (!old_hw_stopped) 239 uport->ops->stop_tx(uport); 240 else 241 __uart_start(state); 242 } 243 uart_port_unlock_irq(uport); 244 } 245 246 static int uart_alloc_xmit_buf(struct tty_port *port) 247 { 248 struct uart_state *state = container_of(port, struct uart_state, port); 249 struct uart_port *uport; 250 unsigned long flags; 251 unsigned long page; 252 253 /* 254 * Initialise and allocate the transmit and temporary 255 * buffer. 256 */ 257 page = get_zeroed_page(GFP_KERNEL); 258 if (!page) 259 return -ENOMEM; 260 261 uport = uart_port_lock(state, flags); 262 if (!state->port.xmit_buf) { 263 state->port.xmit_buf = (unsigned char *)page; 264 kfifo_init(&state->port.xmit_fifo, state->port.xmit_buf, 265 PAGE_SIZE); 266 uart_port_unlock(uport, flags); 267 } else { 268 uart_port_unlock(uport, flags); 269 /* 270 * Do not free() the page under the port lock, see 271 * uart_free_xmit_buf(). 272 */ 273 free_page(page); 274 } 275 276 return 0; 277 } 278 279 static void uart_free_xmit_buf(struct tty_port *port) 280 { 281 struct uart_state *state = container_of(port, struct uart_state, port); 282 struct uart_port *uport; 283 unsigned long flags; 284 char *xmit_buf; 285 286 /* 287 * Do not free() the transmit buffer page under the port lock since 288 * this can create various circular locking scenarios. For instance, 289 * console driver may need to allocate/free a debug object, which 290 * can end up in printk() recursion. 291 */ 292 uport = uart_port_lock(state, flags); 293 xmit_buf = port->xmit_buf; 294 port->xmit_buf = NULL; 295 INIT_KFIFO(port->xmit_fifo); 296 uart_port_unlock(uport, flags); 297 298 free_page((unsigned long)xmit_buf); 299 } 300 301 /* 302 * Startup the port. This will be called once per open. All calls 303 * will be serialised by the per-port mutex. 304 */ 305 static int uart_port_startup(struct tty_struct *tty, struct uart_state *state, 306 bool init_hw) 307 { 308 struct uart_port *uport = uart_port_check(state); 309 int retval; 310 311 if (uport->type == PORT_UNKNOWN) 312 return 1; 313 314 /* 315 * Make sure the device is in D0 state. 316 */ 317 uart_change_pm(state, UART_PM_STATE_ON); 318 319 retval = uart_alloc_xmit_buf(&state->port); 320 if (retval) 321 return retval; 322 323 retval = uport->ops->startup(uport); 324 if (retval == 0) { 325 if (uart_console(uport) && uport->cons->cflag) { 326 tty->termios.c_cflag = uport->cons->cflag; 327 tty->termios.c_ispeed = uport->cons->ispeed; 328 tty->termios.c_ospeed = uport->cons->ospeed; 329 uport->cons->cflag = 0; 330 uport->cons->ispeed = 0; 331 uport->cons->ospeed = 0; 332 } 333 /* 334 * Initialise the hardware port settings. 335 */ 336 uart_change_line_settings(tty, state, NULL); 337 338 /* 339 * Setup the RTS and DTR signals once the 340 * port is open and ready to respond. 341 */ 342 if (init_hw && C_BAUD(tty)) 343 uart_port_dtr_rts(uport, true); 344 } 345 346 /* 347 * This is to allow setserial on this port. People may want to set 348 * port/irq/type and then reconfigure the port properly if it failed 349 * now. 350 */ 351 if (retval && capable(CAP_SYS_ADMIN)) 352 return 1; 353 354 return retval; 355 } 356 357 static int uart_startup(struct tty_struct *tty, struct uart_state *state, 358 bool init_hw) 359 { 360 struct tty_port *port = &state->port; 361 struct uart_port *uport; 362 int retval; 363 364 if (tty_port_initialized(port)) 365 goto out_base_port_startup; 366 367 retval = uart_port_startup(tty, state, init_hw); 368 if (retval) { 369 set_bit(TTY_IO_ERROR, &tty->flags); 370 return retval; 371 } 372 373 out_base_port_startup: 374 uport = uart_port_check(state); 375 if (!uport) 376 return -EIO; 377 378 serial_base_port_startup(uport); 379 380 return 0; 381 } 382 383 /* 384 * This routine will shutdown a serial port; interrupts are disabled, and 385 * DTR is dropped if the hangup on close termio flag is on. Calls to 386 * uart_shutdown are serialised by the per-port semaphore. 387 * 388 * uport == NULL if uart_port has already been removed 389 */ 390 static void uart_shutdown(struct tty_struct *tty, struct uart_state *state) 391 { 392 struct uart_port *uport = uart_port_check(state); 393 struct tty_port *port = &state->port; 394 395 /* 396 * Set the TTY IO error marker 397 */ 398 if (tty) 399 set_bit(TTY_IO_ERROR, &tty->flags); 400 401 if (uport) 402 serial_base_port_shutdown(uport); 403 404 if (tty_port_initialized(port)) { 405 tty_port_set_initialized(port, false); 406 407 /* 408 * Turn off DTR and RTS early. 409 */ 410 if (uport && uart_console(uport) && tty) { 411 uport->cons->cflag = tty->termios.c_cflag; 412 uport->cons->ispeed = tty->termios.c_ispeed; 413 uport->cons->ospeed = tty->termios.c_ospeed; 414 } 415 416 if (!tty || C_HUPCL(tty)) 417 uart_port_dtr_rts(uport, false); 418 419 uart_port_shutdown(port); 420 } 421 422 /* 423 * It's possible for shutdown to be called after suspend if we get 424 * a DCD drop (hangup) at just the right time. Clear suspended bit so 425 * we don't try to resume a port that has been shutdown. 426 */ 427 tty_port_set_suspended(port, false); 428 429 uart_free_xmit_buf(port); 430 } 431 432 /** 433 * uart_update_timeout - update per-port frame timing information 434 * @port: uart_port structure describing the port 435 * @cflag: termios cflag value 436 * @baud: speed of the port 437 * 438 * Set the @port frame timing information from which the FIFO timeout value is 439 * derived. The @cflag value should reflect the actual hardware settings as 440 * number of bits, parity, stop bits and baud rate is taken into account here. 441 * 442 * Locking: caller is expected to take @port->lock 443 */ 444 void 445 uart_update_timeout(struct uart_port *port, unsigned int cflag, 446 unsigned int baud) 447 { 448 u64 temp = tty_get_frame_size(cflag); 449 450 temp *= NSEC_PER_SEC; 451 port->frame_time = (unsigned int)DIV64_U64_ROUND_UP(temp, baud); 452 } 453 EXPORT_SYMBOL(uart_update_timeout); 454 455 /** 456 * uart_get_baud_rate - return baud rate for a particular port 457 * @port: uart_port structure describing the port in question. 458 * @termios: desired termios settings 459 * @old: old termios (or %NULL) 460 * @min: minimum acceptable baud rate 461 * @max: maximum acceptable baud rate 462 * 463 * Decode the termios structure into a numeric baud rate, taking account of the 464 * magic 38400 baud rate (with spd_* flags), and mapping the %B0 rate to 9600 465 * baud. 466 * 467 * If the new baud rate is invalid, try the @old termios setting. If it's still 468 * invalid, we try 9600 baud. If that is also invalid 0 is returned. 469 * 470 * The @termios structure is updated to reflect the baud rate we're actually 471 * going to be using. Don't do this for the case where B0 is requested ("hang 472 * up"). 473 * 474 * Locking: caller dependent 475 */ 476 unsigned int 477 uart_get_baud_rate(struct uart_port *port, struct ktermios *termios, 478 const struct ktermios *old, unsigned int min, unsigned int max) 479 { 480 unsigned int try; 481 unsigned int baud; 482 unsigned int altbaud; 483 int hung_up = 0; 484 upf_t flags = port->flags & UPF_SPD_MASK; 485 486 switch (flags) { 487 case UPF_SPD_HI: 488 altbaud = 57600; 489 break; 490 case UPF_SPD_VHI: 491 altbaud = 115200; 492 break; 493 case UPF_SPD_SHI: 494 altbaud = 230400; 495 break; 496 case UPF_SPD_WARP: 497 altbaud = 460800; 498 break; 499 default: 500 altbaud = 38400; 501 break; 502 } 503 504 for (try = 0; try < 2; try++) { 505 baud = tty_termios_baud_rate(termios); 506 507 /* 508 * The spd_hi, spd_vhi, spd_shi, spd_warp kludge... 509 * Die! Die! Die! 510 */ 511 if (try == 0 && baud == 38400) 512 baud = altbaud; 513 514 /* 515 * Special case: B0 rate. 516 */ 517 if (baud == 0) { 518 hung_up = 1; 519 baud = 9600; 520 } 521 522 if (baud >= min && baud <= max) 523 return baud; 524 525 /* 526 * Oops, the quotient was zero. Try again with 527 * the old baud rate if possible. 528 */ 529 termios->c_cflag &= ~CBAUD; 530 if (old) { 531 baud = tty_termios_baud_rate(old); 532 if (!hung_up) 533 tty_termios_encode_baud_rate(termios, 534 baud, baud); 535 old = NULL; 536 continue; 537 } 538 539 /* 540 * As a last resort, if the range cannot be met then clip to 541 * the nearest chip supported rate. 542 */ 543 if (!hung_up) { 544 if (baud <= min) 545 tty_termios_encode_baud_rate(termios, 546 min + 1, min + 1); 547 else 548 tty_termios_encode_baud_rate(termios, 549 max - 1, max - 1); 550 } 551 } 552 return 0; 553 } 554 EXPORT_SYMBOL(uart_get_baud_rate); 555 556 /** 557 * uart_get_divisor - return uart clock divisor 558 * @port: uart_port structure describing the port 559 * @baud: desired baud rate 560 * 561 * Calculate the divisor (baud_base / baud) for the specified @baud, 562 * appropriately rounded. 563 * 564 * If 38400 baud and custom divisor is selected, return the custom divisor 565 * instead. 566 * 567 * Locking: caller dependent 568 */ 569 unsigned int 570 uart_get_divisor(struct uart_port *port, unsigned int baud) 571 { 572 unsigned int quot; 573 574 /* 575 * Old custom speed handling. 576 */ 577 if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST) 578 quot = port->custom_divisor; 579 else 580 quot = DIV_ROUND_CLOSEST(port->uartclk, 16 * baud); 581 582 return quot; 583 } 584 EXPORT_SYMBOL(uart_get_divisor); 585 586 static int uart_put_char(struct tty_struct *tty, u8 c) 587 { 588 struct uart_state *state = tty->driver_data; 589 struct uart_port *port; 590 unsigned long flags; 591 int ret = 0; 592 593 port = uart_port_lock(state, flags); 594 if (!state->port.xmit_buf) { 595 uart_port_unlock(port, flags); 596 return 0; 597 } 598 599 if (port) 600 ret = kfifo_put(&state->port.xmit_fifo, c); 601 uart_port_unlock(port, flags); 602 return ret; 603 } 604 605 static void uart_flush_chars(struct tty_struct *tty) 606 { 607 uart_start(tty); 608 } 609 610 static ssize_t uart_write(struct tty_struct *tty, const u8 *buf, size_t count) 611 { 612 struct uart_state *state = tty->driver_data; 613 struct uart_port *port; 614 unsigned long flags; 615 int ret = 0; 616 617 /* 618 * This means you called this function _after_ the port was 619 * closed. No cookie for you. 620 */ 621 if (WARN_ON(!state)) 622 return -EL3HLT; 623 624 port = uart_port_lock(state, flags); 625 if (!state->port.xmit_buf) { 626 uart_port_unlock(port, flags); 627 return 0; 628 } 629 630 if (port) 631 ret = kfifo_in(&state->port.xmit_fifo, buf, count); 632 633 __uart_start(state); 634 uart_port_unlock(port, flags); 635 return ret; 636 } 637 638 static unsigned int uart_write_room(struct tty_struct *tty) 639 { 640 struct uart_state *state = tty->driver_data; 641 struct uart_port *port; 642 unsigned long flags; 643 unsigned int ret; 644 645 port = uart_port_lock(state, flags); 646 ret = kfifo_avail(&state->port.xmit_fifo); 647 uart_port_unlock(port, flags); 648 return ret; 649 } 650 651 static unsigned int uart_chars_in_buffer(struct tty_struct *tty) 652 { 653 struct uart_state *state = tty->driver_data; 654 struct uart_port *port; 655 unsigned long flags; 656 unsigned int ret; 657 658 port = uart_port_lock(state, flags); 659 ret = kfifo_len(&state->port.xmit_fifo); 660 uart_port_unlock(port, flags); 661 return ret; 662 } 663 664 static void uart_flush_buffer(struct tty_struct *tty) 665 { 666 struct uart_state *state = tty->driver_data; 667 struct uart_port *port; 668 unsigned long flags; 669 670 /* 671 * This means you called this function _after_ the port was 672 * closed. No cookie for you. 673 */ 674 if (WARN_ON(!state)) 675 return; 676 677 pr_debug("uart_flush_buffer(%d) called\n", tty->index); 678 679 port = uart_port_lock(state, flags); 680 if (!port) 681 return; 682 kfifo_reset(&state->port.xmit_fifo); 683 if (port->ops->flush_buffer) 684 port->ops->flush_buffer(port); 685 uart_port_unlock(port, flags); 686 tty_port_tty_wakeup(&state->port); 687 } 688 689 /* 690 * This function performs low-level write of high-priority XON/XOFF 691 * character and accounting for it. 692 * 693 * Requires uart_port to implement .serial_out(). 694 */ 695 void uart_xchar_out(struct uart_port *uport, int offset) 696 { 697 serial_port_out(uport, offset, uport->x_char); 698 uport->icount.tx++; 699 uport->x_char = 0; 700 } 701 EXPORT_SYMBOL_GPL(uart_xchar_out); 702 703 /* 704 * This function is used to send a high-priority XON/XOFF character to 705 * the device 706 */ 707 static void uart_send_xchar(struct tty_struct *tty, u8 ch) 708 { 709 struct uart_state *state = tty->driver_data; 710 struct uart_port *port; 711 unsigned long flags; 712 713 port = uart_port_ref(state); 714 if (!port) 715 return; 716 717 if (port->ops->send_xchar) 718 port->ops->send_xchar(port, ch); 719 else { 720 uart_port_lock_irqsave(port, &flags); 721 port->x_char = ch; 722 if (ch) 723 port->ops->start_tx(port); 724 uart_port_unlock_irqrestore(port, flags); 725 } 726 uart_port_deref(port); 727 } 728 729 static void uart_throttle(struct tty_struct *tty) 730 { 731 struct uart_state *state = tty->driver_data; 732 upstat_t mask = UPSTAT_SYNC_FIFO; 733 struct uart_port *port; 734 735 port = uart_port_ref(state); 736 if (!port) 737 return; 738 739 if (I_IXOFF(tty)) 740 mask |= UPSTAT_AUTOXOFF; 741 if (C_CRTSCTS(tty)) 742 mask |= UPSTAT_AUTORTS; 743 744 if (port->status & mask) { 745 port->ops->throttle(port); 746 mask &= ~port->status; 747 } 748 749 if (mask & UPSTAT_AUTORTS) 750 uart_clear_mctrl(port, TIOCM_RTS); 751 752 if (mask & UPSTAT_AUTOXOFF) 753 uart_send_xchar(tty, STOP_CHAR(tty)); 754 755 uart_port_deref(port); 756 } 757 758 static void uart_unthrottle(struct tty_struct *tty) 759 { 760 struct uart_state *state = tty->driver_data; 761 upstat_t mask = UPSTAT_SYNC_FIFO; 762 struct uart_port *port; 763 764 port = uart_port_ref(state); 765 if (!port) 766 return; 767 768 if (I_IXOFF(tty)) 769 mask |= UPSTAT_AUTOXOFF; 770 if (C_CRTSCTS(tty)) 771 mask |= UPSTAT_AUTORTS; 772 773 if (port->status & mask) { 774 port->ops->unthrottle(port); 775 mask &= ~port->status; 776 } 777 778 if (mask & UPSTAT_AUTORTS) 779 uart_set_mctrl(port, TIOCM_RTS); 780 781 if (mask & UPSTAT_AUTOXOFF) 782 uart_send_xchar(tty, START_CHAR(tty)); 783 784 uart_port_deref(port); 785 } 786 787 static int uart_get_info(struct tty_port *port, struct serial_struct *retinfo) 788 { 789 struct uart_state *state = container_of(port, struct uart_state, port); 790 struct uart_port *uport; 791 int ret = -ENODEV; 792 793 /* Initialize structure in case we error out later to prevent any stack info leakage. */ 794 *retinfo = (struct serial_struct){}; 795 796 /* 797 * Ensure the state we copy is consistent and no hardware changes 798 * occur as we go 799 */ 800 mutex_lock(&port->mutex); 801 uport = uart_port_check(state); 802 if (!uport) 803 goto out; 804 805 retinfo->type = uport->type; 806 retinfo->line = uport->line; 807 retinfo->port = uport->iobase; 808 if (HIGH_BITS_OFFSET) 809 retinfo->port_high = (long) uport->iobase >> HIGH_BITS_OFFSET; 810 retinfo->irq = uport->irq; 811 retinfo->flags = (__force int)uport->flags; 812 retinfo->xmit_fifo_size = uport->fifosize; 813 retinfo->baud_base = uport->uartclk / 16; 814 retinfo->close_delay = jiffies_to_msecs(port->close_delay) / 10; 815 retinfo->closing_wait = port->closing_wait == ASYNC_CLOSING_WAIT_NONE ? 816 ASYNC_CLOSING_WAIT_NONE : 817 jiffies_to_msecs(port->closing_wait) / 10; 818 retinfo->custom_divisor = uport->custom_divisor; 819 retinfo->hub6 = uport->hub6; 820 retinfo->io_type = uport->iotype; 821 retinfo->iomem_reg_shift = uport->regshift; 822 retinfo->iomem_base = (void *)(unsigned long)uport->mapbase; 823 824 ret = 0; 825 out: 826 mutex_unlock(&port->mutex); 827 return ret; 828 } 829 830 static int uart_get_info_user(struct tty_struct *tty, 831 struct serial_struct *ss) 832 { 833 struct uart_state *state = tty->driver_data; 834 struct tty_port *port = &state->port; 835 836 return uart_get_info(port, ss) < 0 ? -EIO : 0; 837 } 838 839 static int uart_set_info(struct tty_struct *tty, struct tty_port *port, 840 struct uart_state *state, 841 struct serial_struct *new_info) 842 { 843 struct uart_port *uport = uart_port_check(state); 844 unsigned long new_port; 845 unsigned int change_irq, change_port, closing_wait; 846 unsigned int old_custom_divisor, close_delay; 847 upf_t old_flags, new_flags; 848 int retval = 0; 849 850 if (!uport) 851 return -EIO; 852 853 new_port = new_info->port; 854 if (HIGH_BITS_OFFSET) 855 new_port += (unsigned long) new_info->port_high << HIGH_BITS_OFFSET; 856 857 new_info->irq = irq_canonicalize(new_info->irq); 858 close_delay = msecs_to_jiffies(new_info->close_delay * 10); 859 closing_wait = new_info->closing_wait == ASYNC_CLOSING_WAIT_NONE ? 860 ASYNC_CLOSING_WAIT_NONE : 861 msecs_to_jiffies(new_info->closing_wait * 10); 862 863 864 change_irq = !(uport->flags & UPF_FIXED_PORT) 865 && new_info->irq != uport->irq; 866 867 /* 868 * Since changing the 'type' of the port changes its resource 869 * allocations, we should treat type changes the same as 870 * IO port changes. 871 */ 872 change_port = !(uport->flags & UPF_FIXED_PORT) 873 && (new_port != uport->iobase || 874 (unsigned long)new_info->iomem_base != uport->mapbase || 875 new_info->hub6 != uport->hub6 || 876 new_info->io_type != uport->iotype || 877 new_info->iomem_reg_shift != uport->regshift || 878 new_info->type != uport->type); 879 880 old_flags = uport->flags; 881 new_flags = (__force upf_t)new_info->flags; 882 old_custom_divisor = uport->custom_divisor; 883 884 if (!(uport->flags & UPF_FIXED_PORT)) { 885 unsigned int uartclk = new_info->baud_base * 16; 886 /* check needs to be done here before other settings made */ 887 if (uartclk == 0) { 888 retval = -EINVAL; 889 goto exit; 890 } 891 } 892 if (!capable(CAP_SYS_ADMIN)) { 893 retval = -EPERM; 894 if (change_irq || change_port || 895 (new_info->baud_base != uport->uartclk / 16) || 896 (close_delay != port->close_delay) || 897 (closing_wait != port->closing_wait) || 898 (new_info->xmit_fifo_size && 899 new_info->xmit_fifo_size != uport->fifosize) || 900 (((new_flags ^ old_flags) & ~UPF_USR_MASK) != 0)) 901 goto exit; 902 uport->flags = ((uport->flags & ~UPF_USR_MASK) | 903 (new_flags & UPF_USR_MASK)); 904 uport->custom_divisor = new_info->custom_divisor; 905 goto check_and_exit; 906 } 907 908 if (change_irq || change_port) { 909 retval = security_locked_down(LOCKDOWN_TIOCSSERIAL); 910 if (retval) 911 goto exit; 912 } 913 914 /* 915 * Ask the low level driver to verify the settings. 916 */ 917 if (uport->ops->verify_port) 918 retval = uport->ops->verify_port(uport, new_info); 919 920 if ((new_info->irq >= nr_irqs) || (new_info->irq < 0) || 921 (new_info->baud_base < 9600)) 922 retval = -EINVAL; 923 924 if (retval) 925 goto exit; 926 927 if (change_port || change_irq) { 928 retval = -EBUSY; 929 930 /* 931 * Make sure that we are the sole user of this port. 932 */ 933 if (tty_port_users(port) > 1) 934 goto exit; 935 936 /* 937 * We need to shutdown the serial port at the old 938 * port/type/irq combination. 939 */ 940 uart_shutdown(tty, state); 941 } 942 943 if (change_port) { 944 unsigned long old_iobase, old_mapbase; 945 unsigned int old_type, old_iotype, old_hub6, old_shift; 946 947 old_iobase = uport->iobase; 948 old_mapbase = uport->mapbase; 949 old_type = uport->type; 950 old_hub6 = uport->hub6; 951 old_iotype = uport->iotype; 952 old_shift = uport->regshift; 953 954 /* 955 * Free and release old regions 956 */ 957 if (old_type != PORT_UNKNOWN && uport->ops->release_port) 958 uport->ops->release_port(uport); 959 960 uport->iobase = new_port; 961 uport->type = new_info->type; 962 uport->hub6 = new_info->hub6; 963 uport->iotype = new_info->io_type; 964 uport->regshift = new_info->iomem_reg_shift; 965 uport->mapbase = (unsigned long)new_info->iomem_base; 966 967 /* 968 * Claim and map the new regions 969 */ 970 if (uport->type != PORT_UNKNOWN && uport->ops->request_port) { 971 retval = uport->ops->request_port(uport); 972 } else { 973 /* Always success - Jean II */ 974 retval = 0; 975 } 976 977 /* 978 * If we fail to request resources for the 979 * new port, try to restore the old settings. 980 */ 981 if (retval) { 982 uport->iobase = old_iobase; 983 uport->type = old_type; 984 uport->hub6 = old_hub6; 985 uport->iotype = old_iotype; 986 uport->regshift = old_shift; 987 uport->mapbase = old_mapbase; 988 989 if (old_type != PORT_UNKNOWN) { 990 retval = uport->ops->request_port(uport); 991 /* 992 * If we failed to restore the old settings, 993 * we fail like this. 994 */ 995 if (retval) 996 uport->type = PORT_UNKNOWN; 997 998 /* 999 * We failed anyway. 1000 */ 1001 retval = -EBUSY; 1002 } 1003 1004 /* Added to return the correct error -Ram Gupta */ 1005 goto exit; 1006 } 1007 } 1008 1009 if (change_irq) 1010 uport->irq = new_info->irq; 1011 if (!(uport->flags & UPF_FIXED_PORT)) 1012 uport->uartclk = new_info->baud_base * 16; 1013 uport->flags = (uport->flags & ~UPF_CHANGE_MASK) | 1014 (new_flags & UPF_CHANGE_MASK); 1015 uport->custom_divisor = new_info->custom_divisor; 1016 port->close_delay = close_delay; 1017 port->closing_wait = closing_wait; 1018 if (new_info->xmit_fifo_size) 1019 uport->fifosize = new_info->xmit_fifo_size; 1020 1021 check_and_exit: 1022 retval = 0; 1023 if (uport->type == PORT_UNKNOWN) 1024 goto exit; 1025 if (tty_port_initialized(port)) { 1026 if (((old_flags ^ uport->flags) & UPF_SPD_MASK) || 1027 old_custom_divisor != uport->custom_divisor) { 1028 /* 1029 * If they're setting up a custom divisor or speed, 1030 * instead of clearing it, then bitch about it. 1031 */ 1032 if (uport->flags & UPF_SPD_MASK) { 1033 dev_notice_ratelimited(uport->dev, 1034 "%s sets custom speed on %s. This is deprecated.\n", 1035 current->comm, 1036 tty_name(port->tty)); 1037 } 1038 uart_change_line_settings(tty, state, NULL); 1039 } 1040 } else { 1041 retval = uart_startup(tty, state, true); 1042 if (retval == 0) 1043 tty_port_set_initialized(port, true); 1044 if (retval > 0) 1045 retval = 0; 1046 } 1047 exit: 1048 return retval; 1049 } 1050 1051 static int uart_set_info_user(struct tty_struct *tty, struct serial_struct *ss) 1052 { 1053 struct uart_state *state = tty->driver_data; 1054 struct tty_port *port = &state->port; 1055 int retval; 1056 1057 down_write(&tty->termios_rwsem); 1058 /* 1059 * This semaphore protects port->count. It is also 1060 * very useful to prevent opens. Also, take the 1061 * port configuration semaphore to make sure that a 1062 * module insertion/removal doesn't change anything 1063 * under us. 1064 */ 1065 mutex_lock(&port->mutex); 1066 retval = uart_set_info(tty, port, state, ss); 1067 mutex_unlock(&port->mutex); 1068 up_write(&tty->termios_rwsem); 1069 return retval; 1070 } 1071 1072 /** 1073 * uart_get_lsr_info - get line status register info 1074 * @tty: tty associated with the UART 1075 * @state: UART being queried 1076 * @value: returned modem value 1077 */ 1078 static int uart_get_lsr_info(struct tty_struct *tty, 1079 struct uart_state *state, unsigned int __user *value) 1080 { 1081 struct uart_port *uport = uart_port_check(state); 1082 unsigned int result; 1083 1084 result = uport->ops->tx_empty(uport); 1085 1086 /* 1087 * If we're about to load something into the transmit 1088 * register, we'll pretend the transmitter isn't empty to 1089 * avoid a race condition (depending on when the transmit 1090 * interrupt happens). 1091 */ 1092 if (uport->x_char || 1093 (!kfifo_is_empty(&state->port.xmit_fifo) && 1094 !uart_tx_stopped(uport))) 1095 result &= ~TIOCSER_TEMT; 1096 1097 return put_user(result, value); 1098 } 1099 1100 static int uart_tiocmget(struct tty_struct *tty) 1101 { 1102 struct uart_state *state = tty->driver_data; 1103 struct tty_port *port = &state->port; 1104 struct uart_port *uport; 1105 int result = -EIO; 1106 1107 mutex_lock(&port->mutex); 1108 uport = uart_port_check(state); 1109 if (!uport) 1110 goto out; 1111 1112 if (!tty_io_error(tty)) { 1113 uart_port_lock_irq(uport); 1114 result = uport->mctrl; 1115 result |= uport->ops->get_mctrl(uport); 1116 uart_port_unlock_irq(uport); 1117 } 1118 out: 1119 mutex_unlock(&port->mutex); 1120 return result; 1121 } 1122 1123 static int 1124 uart_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear) 1125 { 1126 struct uart_state *state = tty->driver_data; 1127 struct tty_port *port = &state->port; 1128 struct uart_port *uport; 1129 int ret = -EIO; 1130 1131 mutex_lock(&port->mutex); 1132 uport = uart_port_check(state); 1133 if (!uport) 1134 goto out; 1135 1136 if (!tty_io_error(tty)) { 1137 uart_update_mctrl(uport, set, clear); 1138 ret = 0; 1139 } 1140 out: 1141 mutex_unlock(&port->mutex); 1142 return ret; 1143 } 1144 1145 static int uart_break_ctl(struct tty_struct *tty, int break_state) 1146 { 1147 struct uart_state *state = tty->driver_data; 1148 struct tty_port *port = &state->port; 1149 struct uart_port *uport; 1150 int ret = -EIO; 1151 1152 mutex_lock(&port->mutex); 1153 uport = uart_port_check(state); 1154 if (!uport) 1155 goto out; 1156 1157 if (uport->type != PORT_UNKNOWN && uport->ops->break_ctl) 1158 uport->ops->break_ctl(uport, break_state); 1159 ret = 0; 1160 out: 1161 mutex_unlock(&port->mutex); 1162 return ret; 1163 } 1164 1165 static int uart_do_autoconfig(struct tty_struct *tty, struct uart_state *state) 1166 { 1167 struct tty_port *port = &state->port; 1168 struct uart_port *uport; 1169 int flags, ret; 1170 1171 if (!capable(CAP_SYS_ADMIN)) 1172 return -EPERM; 1173 1174 /* 1175 * Take the per-port semaphore. This prevents count from 1176 * changing, and hence any extra opens of the port while 1177 * we're auto-configuring. 1178 */ 1179 if (mutex_lock_interruptible(&port->mutex)) 1180 return -ERESTARTSYS; 1181 1182 uport = uart_port_check(state); 1183 if (!uport) { 1184 ret = -EIO; 1185 goto out; 1186 } 1187 1188 ret = -EBUSY; 1189 if (tty_port_users(port) == 1) { 1190 uart_shutdown(tty, state); 1191 1192 /* 1193 * If we already have a port type configured, 1194 * we must release its resources. 1195 */ 1196 if (uport->type != PORT_UNKNOWN && uport->ops->release_port) 1197 uport->ops->release_port(uport); 1198 1199 flags = UART_CONFIG_TYPE; 1200 if (uport->flags & UPF_AUTO_IRQ) 1201 flags |= UART_CONFIG_IRQ; 1202 1203 /* 1204 * This will claim the ports resources if 1205 * a port is found. 1206 */ 1207 uport->ops->config_port(uport, flags); 1208 1209 ret = uart_startup(tty, state, true); 1210 if (ret == 0) 1211 tty_port_set_initialized(port, true); 1212 if (ret > 0) 1213 ret = 0; 1214 } 1215 out: 1216 mutex_unlock(&port->mutex); 1217 return ret; 1218 } 1219 1220 static void uart_enable_ms(struct uart_port *uport) 1221 { 1222 /* 1223 * Force modem status interrupts on 1224 */ 1225 if (uport->ops->enable_ms) 1226 uport->ops->enable_ms(uport); 1227 } 1228 1229 /* 1230 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change 1231 * - mask passed in arg for lines of interest 1232 * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) 1233 * Caller should use TIOCGICOUNT to see which one it was 1234 * 1235 * FIXME: This wants extracting into a common all driver implementation 1236 * of TIOCMWAIT using tty_port. 1237 */ 1238 static int uart_wait_modem_status(struct uart_state *state, unsigned long arg) 1239 { 1240 struct uart_port *uport; 1241 struct tty_port *port = &state->port; 1242 DECLARE_WAITQUEUE(wait, current); 1243 struct uart_icount cprev, cnow; 1244 int ret; 1245 1246 /* 1247 * note the counters on entry 1248 */ 1249 uport = uart_port_ref(state); 1250 if (!uport) 1251 return -EIO; 1252 uart_port_lock_irq(uport); 1253 memcpy(&cprev, &uport->icount, sizeof(struct uart_icount)); 1254 uart_enable_ms(uport); 1255 uart_port_unlock_irq(uport); 1256 1257 add_wait_queue(&port->delta_msr_wait, &wait); 1258 for (;;) { 1259 uart_port_lock_irq(uport); 1260 memcpy(&cnow, &uport->icount, sizeof(struct uart_icount)); 1261 uart_port_unlock_irq(uport); 1262 1263 set_current_state(TASK_INTERRUPTIBLE); 1264 1265 if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || 1266 ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || 1267 ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || 1268 ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) { 1269 ret = 0; 1270 break; 1271 } 1272 1273 schedule(); 1274 1275 /* see if a signal did it */ 1276 if (signal_pending(current)) { 1277 ret = -ERESTARTSYS; 1278 break; 1279 } 1280 1281 cprev = cnow; 1282 } 1283 __set_current_state(TASK_RUNNING); 1284 remove_wait_queue(&port->delta_msr_wait, &wait); 1285 uart_port_deref(uport); 1286 1287 return ret; 1288 } 1289 1290 /* 1291 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS) 1292 * Return: write counters to the user passed counter struct 1293 * NB: both 1->0 and 0->1 transitions are counted except for 1294 * RI where only 0->1 is counted. 1295 */ 1296 static int uart_get_icount(struct tty_struct *tty, 1297 struct serial_icounter_struct *icount) 1298 { 1299 struct uart_state *state = tty->driver_data; 1300 struct uart_icount cnow; 1301 struct uart_port *uport; 1302 1303 uport = uart_port_ref(state); 1304 if (!uport) 1305 return -EIO; 1306 uart_port_lock_irq(uport); 1307 memcpy(&cnow, &uport->icount, sizeof(struct uart_icount)); 1308 uart_port_unlock_irq(uport); 1309 uart_port_deref(uport); 1310 1311 icount->cts = cnow.cts; 1312 icount->dsr = cnow.dsr; 1313 icount->rng = cnow.rng; 1314 icount->dcd = cnow.dcd; 1315 icount->rx = cnow.rx; 1316 icount->tx = cnow.tx; 1317 icount->frame = cnow.frame; 1318 icount->overrun = cnow.overrun; 1319 icount->parity = cnow.parity; 1320 icount->brk = cnow.brk; 1321 icount->buf_overrun = cnow.buf_overrun; 1322 1323 return 0; 1324 } 1325 1326 #define SER_RS485_LEGACY_FLAGS (SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | \ 1327 SER_RS485_RTS_AFTER_SEND | SER_RS485_RX_DURING_TX | \ 1328 SER_RS485_TERMINATE_BUS) 1329 1330 static int uart_check_rs485_flags(struct uart_port *port, struct serial_rs485 *rs485) 1331 { 1332 u32 flags = rs485->flags; 1333 1334 /* Don't return -EINVAL for unsupported legacy flags */ 1335 flags &= ~SER_RS485_LEGACY_FLAGS; 1336 1337 /* 1338 * For any bit outside of the legacy ones that is not supported by 1339 * the driver, return -EINVAL. 1340 */ 1341 if (flags & ~port->rs485_supported.flags) 1342 return -EINVAL; 1343 1344 /* Asking for address w/o addressing mode? */ 1345 if (!(rs485->flags & SER_RS485_ADDRB) && 1346 (rs485->flags & (SER_RS485_ADDR_RECV|SER_RS485_ADDR_DEST))) 1347 return -EINVAL; 1348 1349 /* Address given but not enabled? */ 1350 if (!(rs485->flags & SER_RS485_ADDR_RECV) && rs485->addr_recv) 1351 return -EINVAL; 1352 if (!(rs485->flags & SER_RS485_ADDR_DEST) && rs485->addr_dest) 1353 return -EINVAL; 1354 1355 return 0; 1356 } 1357 1358 static void uart_sanitize_serial_rs485_delays(struct uart_port *port, 1359 struct serial_rs485 *rs485) 1360 { 1361 if (!port->rs485_supported.delay_rts_before_send) { 1362 if (rs485->delay_rts_before_send) { 1363 dev_warn_ratelimited(port->dev, 1364 "%s (%d): RTS delay before sending not supported\n", 1365 port->name, port->line); 1366 } 1367 rs485->delay_rts_before_send = 0; 1368 } else if (rs485->delay_rts_before_send > RS485_MAX_RTS_DELAY) { 1369 rs485->delay_rts_before_send = RS485_MAX_RTS_DELAY; 1370 dev_warn_ratelimited(port->dev, 1371 "%s (%d): RTS delay before sending clamped to %u ms\n", 1372 port->name, port->line, rs485->delay_rts_before_send); 1373 } 1374 1375 if (!port->rs485_supported.delay_rts_after_send) { 1376 if (rs485->delay_rts_after_send) { 1377 dev_warn_ratelimited(port->dev, 1378 "%s (%d): RTS delay after sending not supported\n", 1379 port->name, port->line); 1380 } 1381 rs485->delay_rts_after_send = 0; 1382 } else if (rs485->delay_rts_after_send > RS485_MAX_RTS_DELAY) { 1383 rs485->delay_rts_after_send = RS485_MAX_RTS_DELAY; 1384 dev_warn_ratelimited(port->dev, 1385 "%s (%d): RTS delay after sending clamped to %u ms\n", 1386 port->name, port->line, rs485->delay_rts_after_send); 1387 } 1388 } 1389 1390 static void uart_sanitize_serial_rs485(struct uart_port *port, struct serial_rs485 *rs485) 1391 { 1392 u32 supported_flags = port->rs485_supported.flags; 1393 1394 if (!(rs485->flags & SER_RS485_ENABLED)) { 1395 memset(rs485, 0, sizeof(*rs485)); 1396 return; 1397 } 1398 1399 /* Clear other RS485 flags but SER_RS485_TERMINATE_BUS and return if enabling RS422 */ 1400 if (rs485->flags & SER_RS485_MODE_RS422) { 1401 rs485->flags &= (SER_RS485_ENABLED | SER_RS485_MODE_RS422 | SER_RS485_TERMINATE_BUS); 1402 return; 1403 } 1404 1405 rs485->flags &= supported_flags; 1406 1407 /* Pick sane settings if the user hasn't */ 1408 if (!(rs485->flags & SER_RS485_RTS_ON_SEND) == 1409 !(rs485->flags & SER_RS485_RTS_AFTER_SEND)) { 1410 if (supported_flags & SER_RS485_RTS_ON_SEND) { 1411 rs485->flags |= SER_RS485_RTS_ON_SEND; 1412 rs485->flags &= ~SER_RS485_RTS_AFTER_SEND; 1413 1414 dev_warn_ratelimited(port->dev, 1415 "%s (%d): invalid RTS setting, using RTS_ON_SEND instead\n", 1416 port->name, port->line); 1417 } else { 1418 rs485->flags |= SER_RS485_RTS_AFTER_SEND; 1419 rs485->flags &= ~SER_RS485_RTS_ON_SEND; 1420 1421 dev_warn_ratelimited(port->dev, 1422 "%s (%d): invalid RTS setting, using RTS_AFTER_SEND instead\n", 1423 port->name, port->line); 1424 } 1425 } 1426 1427 uart_sanitize_serial_rs485_delays(port, rs485); 1428 1429 /* Return clean padding area to userspace */ 1430 memset(rs485->padding0, 0, sizeof(rs485->padding0)); 1431 memset(rs485->padding1, 0, sizeof(rs485->padding1)); 1432 } 1433 1434 static void uart_set_rs485_termination(struct uart_port *port, 1435 const struct serial_rs485 *rs485) 1436 { 1437 if (!(rs485->flags & SER_RS485_ENABLED)) 1438 return; 1439 1440 gpiod_set_value_cansleep(port->rs485_term_gpio, 1441 !!(rs485->flags & SER_RS485_TERMINATE_BUS)); 1442 } 1443 1444 static void uart_set_rs485_rx_during_tx(struct uart_port *port, 1445 const struct serial_rs485 *rs485) 1446 { 1447 if (!(rs485->flags & SER_RS485_ENABLED)) 1448 return; 1449 1450 gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio, 1451 !!(rs485->flags & SER_RS485_RX_DURING_TX)); 1452 } 1453 1454 static int uart_rs485_config(struct uart_port *port) 1455 { 1456 struct serial_rs485 *rs485 = &port->rs485; 1457 unsigned long flags; 1458 int ret; 1459 1460 if (!(rs485->flags & SER_RS485_ENABLED)) 1461 return 0; 1462 1463 uart_sanitize_serial_rs485(port, rs485); 1464 uart_set_rs485_termination(port, rs485); 1465 uart_set_rs485_rx_during_tx(port, rs485); 1466 1467 uart_port_lock_irqsave(port, &flags); 1468 ret = port->rs485_config(port, NULL, rs485); 1469 uart_port_unlock_irqrestore(port, flags); 1470 if (ret) { 1471 memset(rs485, 0, sizeof(*rs485)); 1472 /* unset GPIOs */ 1473 gpiod_set_value_cansleep(port->rs485_term_gpio, 0); 1474 gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio, 0); 1475 } 1476 1477 return ret; 1478 } 1479 1480 static int uart_get_rs485_config(struct uart_port *port, 1481 struct serial_rs485 __user *rs485) 1482 { 1483 unsigned long flags; 1484 struct serial_rs485 aux; 1485 1486 uart_port_lock_irqsave(port, &flags); 1487 aux = port->rs485; 1488 uart_port_unlock_irqrestore(port, flags); 1489 1490 if (copy_to_user(rs485, &aux, sizeof(aux))) 1491 return -EFAULT; 1492 1493 return 0; 1494 } 1495 1496 static int uart_set_rs485_config(struct tty_struct *tty, struct uart_port *port, 1497 struct serial_rs485 __user *rs485_user) 1498 { 1499 struct serial_rs485 rs485; 1500 int ret; 1501 unsigned long flags; 1502 1503 if (!(port->rs485_supported.flags & SER_RS485_ENABLED)) 1504 return -ENOTTY; 1505 1506 if (copy_from_user(&rs485, rs485_user, sizeof(*rs485_user))) 1507 return -EFAULT; 1508 1509 ret = uart_check_rs485_flags(port, &rs485); 1510 if (ret) 1511 return ret; 1512 uart_sanitize_serial_rs485(port, &rs485); 1513 uart_set_rs485_termination(port, &rs485); 1514 uart_set_rs485_rx_during_tx(port, &rs485); 1515 1516 uart_port_lock_irqsave(port, &flags); 1517 ret = port->rs485_config(port, &tty->termios, &rs485); 1518 if (!ret) { 1519 port->rs485 = rs485; 1520 1521 /* Reset RTS and other mctrl lines when disabling RS485 */ 1522 if (!(rs485.flags & SER_RS485_ENABLED)) 1523 port->ops->set_mctrl(port, port->mctrl); 1524 } 1525 uart_port_unlock_irqrestore(port, flags); 1526 if (ret) { 1527 /* restore old GPIO settings */ 1528 gpiod_set_value_cansleep(port->rs485_term_gpio, 1529 !!(port->rs485.flags & SER_RS485_TERMINATE_BUS)); 1530 gpiod_set_value_cansleep(port->rs485_rx_during_tx_gpio, 1531 !!(port->rs485.flags & SER_RS485_RX_DURING_TX)); 1532 return ret; 1533 } 1534 1535 if (copy_to_user(rs485_user, &port->rs485, sizeof(port->rs485))) 1536 return -EFAULT; 1537 1538 return 0; 1539 } 1540 1541 static int uart_get_iso7816_config(struct uart_port *port, 1542 struct serial_iso7816 __user *iso7816) 1543 { 1544 unsigned long flags; 1545 struct serial_iso7816 aux; 1546 1547 if (!port->iso7816_config) 1548 return -ENOTTY; 1549 1550 uart_port_lock_irqsave(port, &flags); 1551 aux = port->iso7816; 1552 uart_port_unlock_irqrestore(port, flags); 1553 1554 if (copy_to_user(iso7816, &aux, sizeof(aux))) 1555 return -EFAULT; 1556 1557 return 0; 1558 } 1559 1560 static int uart_set_iso7816_config(struct uart_port *port, 1561 struct serial_iso7816 __user *iso7816_user) 1562 { 1563 struct serial_iso7816 iso7816; 1564 int i, ret; 1565 unsigned long flags; 1566 1567 if (!port->iso7816_config) 1568 return -ENOTTY; 1569 1570 if (copy_from_user(&iso7816, iso7816_user, sizeof(*iso7816_user))) 1571 return -EFAULT; 1572 1573 /* 1574 * There are 5 words reserved for future use. Check that userspace 1575 * doesn't put stuff in there to prevent breakages in the future. 1576 */ 1577 for (i = 0; i < ARRAY_SIZE(iso7816.reserved); i++) 1578 if (iso7816.reserved[i]) 1579 return -EINVAL; 1580 1581 uart_port_lock_irqsave(port, &flags); 1582 ret = port->iso7816_config(port, &iso7816); 1583 uart_port_unlock_irqrestore(port, flags); 1584 if (ret) 1585 return ret; 1586 1587 if (copy_to_user(iso7816_user, &port->iso7816, sizeof(port->iso7816))) 1588 return -EFAULT; 1589 1590 return 0; 1591 } 1592 1593 /* 1594 * Called via sys_ioctl. We can use spin_lock_irq() here. 1595 */ 1596 static int 1597 uart_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg) 1598 { 1599 struct uart_state *state = tty->driver_data; 1600 struct tty_port *port = &state->port; 1601 struct uart_port *uport; 1602 void __user *uarg = (void __user *)arg; 1603 int ret = -ENOIOCTLCMD; 1604 1605 1606 /* 1607 * These ioctls don't rely on the hardware to be present. 1608 */ 1609 switch (cmd) { 1610 case TIOCSERCONFIG: 1611 down_write(&tty->termios_rwsem); 1612 ret = uart_do_autoconfig(tty, state); 1613 up_write(&tty->termios_rwsem); 1614 break; 1615 } 1616 1617 if (ret != -ENOIOCTLCMD) 1618 goto out; 1619 1620 if (tty_io_error(tty)) { 1621 ret = -EIO; 1622 goto out; 1623 } 1624 1625 /* 1626 * The following should only be used when hardware is present. 1627 */ 1628 switch (cmd) { 1629 case TIOCMIWAIT: 1630 ret = uart_wait_modem_status(state, arg); 1631 break; 1632 } 1633 1634 if (ret != -ENOIOCTLCMD) 1635 goto out; 1636 1637 /* rs485_config requires more locking than others */ 1638 if (cmd == TIOCSRS485) 1639 down_write(&tty->termios_rwsem); 1640 1641 mutex_lock(&port->mutex); 1642 uport = uart_port_check(state); 1643 1644 if (!uport || tty_io_error(tty)) { 1645 ret = -EIO; 1646 goto out_up; 1647 } 1648 1649 /* 1650 * All these rely on hardware being present and need to be 1651 * protected against the tty being hung up. 1652 */ 1653 1654 switch (cmd) { 1655 case TIOCSERGETLSR: /* Get line status register */ 1656 ret = uart_get_lsr_info(tty, state, uarg); 1657 break; 1658 1659 case TIOCGRS485: 1660 ret = uart_get_rs485_config(uport, uarg); 1661 break; 1662 1663 case TIOCSRS485: 1664 ret = uart_set_rs485_config(tty, uport, uarg); 1665 break; 1666 1667 case TIOCSISO7816: 1668 ret = uart_set_iso7816_config(state->uart_port, uarg); 1669 break; 1670 1671 case TIOCGISO7816: 1672 ret = uart_get_iso7816_config(state->uart_port, uarg); 1673 break; 1674 default: 1675 if (uport->ops->ioctl) 1676 ret = uport->ops->ioctl(uport, cmd, arg); 1677 break; 1678 } 1679 out_up: 1680 mutex_unlock(&port->mutex); 1681 if (cmd == TIOCSRS485) 1682 up_write(&tty->termios_rwsem); 1683 out: 1684 return ret; 1685 } 1686 1687 static void uart_set_ldisc(struct tty_struct *tty) 1688 { 1689 struct uart_state *state = tty->driver_data; 1690 struct uart_port *uport; 1691 struct tty_port *port = &state->port; 1692 1693 if (!tty_port_initialized(port)) 1694 return; 1695 1696 mutex_lock(&state->port.mutex); 1697 uport = uart_port_check(state); 1698 if (uport && uport->ops->set_ldisc) 1699 uport->ops->set_ldisc(uport, &tty->termios); 1700 mutex_unlock(&state->port.mutex); 1701 } 1702 1703 static void uart_set_termios(struct tty_struct *tty, 1704 const struct ktermios *old_termios) 1705 { 1706 struct uart_state *state = tty->driver_data; 1707 struct uart_port *uport; 1708 unsigned int cflag = tty->termios.c_cflag; 1709 unsigned int iflag_mask = IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK; 1710 bool sw_changed = false; 1711 1712 mutex_lock(&state->port.mutex); 1713 uport = uart_port_check(state); 1714 if (!uport) 1715 goto out; 1716 1717 /* 1718 * Drivers doing software flow control also need to know 1719 * about changes to these input settings. 1720 */ 1721 if (uport->flags & UPF_SOFT_FLOW) { 1722 iflag_mask |= IXANY|IXON|IXOFF; 1723 sw_changed = 1724 tty->termios.c_cc[VSTART] != old_termios->c_cc[VSTART] || 1725 tty->termios.c_cc[VSTOP] != old_termios->c_cc[VSTOP]; 1726 } 1727 1728 /* 1729 * These are the bits that are used to setup various 1730 * flags in the low level driver. We can ignore the Bfoo 1731 * bits in c_cflag; c_[io]speed will always be set 1732 * appropriately by set_termios() in tty_ioctl.c 1733 */ 1734 if ((cflag ^ old_termios->c_cflag) == 0 && 1735 tty->termios.c_ospeed == old_termios->c_ospeed && 1736 tty->termios.c_ispeed == old_termios->c_ispeed && 1737 ((tty->termios.c_iflag ^ old_termios->c_iflag) & iflag_mask) == 0 && 1738 !sw_changed) { 1739 goto out; 1740 } 1741 1742 uart_change_line_settings(tty, state, old_termios); 1743 /* reload cflag from termios; port driver may have overridden flags */ 1744 cflag = tty->termios.c_cflag; 1745 1746 /* Handle transition to B0 status */ 1747 if (((old_termios->c_cflag & CBAUD) != B0) && ((cflag & CBAUD) == B0)) 1748 uart_clear_mctrl(uport, TIOCM_RTS | TIOCM_DTR); 1749 /* Handle transition away from B0 status */ 1750 else if (((old_termios->c_cflag & CBAUD) == B0) && ((cflag & CBAUD) != B0)) { 1751 unsigned int mask = TIOCM_DTR; 1752 1753 if (!(cflag & CRTSCTS) || !tty_throttled(tty)) 1754 mask |= TIOCM_RTS; 1755 uart_set_mctrl(uport, mask); 1756 } 1757 out: 1758 mutex_unlock(&state->port.mutex); 1759 } 1760 1761 /* 1762 * Calls to uart_close() are serialised via the tty_lock in 1763 * drivers/tty/tty_io.c:tty_release() 1764 * drivers/tty/tty_io.c:do_tty_hangup() 1765 */ 1766 static void uart_close(struct tty_struct *tty, struct file *filp) 1767 { 1768 struct uart_state *state = tty->driver_data; 1769 1770 if (!state) { 1771 struct uart_driver *drv = tty->driver->driver_state; 1772 struct tty_port *port; 1773 1774 state = drv->state + tty->index; 1775 port = &state->port; 1776 spin_lock_irq(&port->lock); 1777 --port->count; 1778 spin_unlock_irq(&port->lock); 1779 return; 1780 } 1781 1782 pr_debug("uart_close(%d) called\n", tty->index); 1783 1784 tty_port_close(tty->port, tty, filp); 1785 } 1786 1787 static void uart_tty_port_shutdown(struct tty_port *port) 1788 { 1789 struct uart_state *state = container_of(port, struct uart_state, port); 1790 struct uart_port *uport = uart_port_check(state); 1791 1792 /* 1793 * At this point, we stop accepting input. To do this, we 1794 * disable the receive line status interrupts. 1795 */ 1796 if (WARN(!uport, "detached port still initialized!\n")) 1797 return; 1798 1799 uart_port_lock_irq(uport); 1800 uport->ops->stop_rx(uport); 1801 uart_port_unlock_irq(uport); 1802 1803 serial_base_port_shutdown(uport); 1804 uart_port_shutdown(port); 1805 1806 /* 1807 * It's possible for shutdown to be called after suspend if we get 1808 * a DCD drop (hangup) at just the right time. Clear suspended bit so 1809 * we don't try to resume a port that has been shutdown. 1810 */ 1811 tty_port_set_suspended(port, false); 1812 1813 uart_free_xmit_buf(port); 1814 1815 uart_change_pm(state, UART_PM_STATE_OFF); 1816 } 1817 1818 static void uart_wait_until_sent(struct tty_struct *tty, int timeout) 1819 { 1820 struct uart_state *state = tty->driver_data; 1821 struct uart_port *port; 1822 unsigned long char_time, expire, fifo_timeout; 1823 1824 port = uart_port_ref(state); 1825 if (!port) 1826 return; 1827 1828 if (port->type == PORT_UNKNOWN || port->fifosize == 0) { 1829 uart_port_deref(port); 1830 return; 1831 } 1832 1833 /* 1834 * Set the check interval to be 1/5 of the estimated time to 1835 * send a single character, and make it at least 1. The check 1836 * interval should also be less than the timeout. 1837 * 1838 * Note: we have to use pretty tight timings here to satisfy 1839 * the NIST-PCTS. 1840 */ 1841 char_time = max(nsecs_to_jiffies(port->frame_time / 5), 1UL); 1842 1843 if (timeout && timeout < char_time) 1844 char_time = timeout; 1845 1846 if (!uart_cts_enabled(port)) { 1847 /* 1848 * If the transmitter hasn't cleared in twice the approximate 1849 * amount of time to send the entire FIFO, it probably won't 1850 * ever clear. This assumes the UART isn't doing flow 1851 * control, which is currently the case. Hence, if it ever 1852 * takes longer than FIFO timeout, this is probably due to a 1853 * UART bug of some kind. So, we clamp the timeout parameter at 1854 * 2 * FIFO timeout. 1855 */ 1856 fifo_timeout = uart_fifo_timeout(port); 1857 if (timeout == 0 || timeout > 2 * fifo_timeout) 1858 timeout = 2 * fifo_timeout; 1859 } 1860 1861 expire = jiffies + timeout; 1862 1863 pr_debug("uart_wait_until_sent(%d), jiffies=%lu, expire=%lu...\n", 1864 port->line, jiffies, expire); 1865 1866 /* 1867 * Check whether the transmitter is empty every 'char_time'. 1868 * 'timeout' / 'expire' give us the maximum amount of time 1869 * we wait. 1870 */ 1871 while (!port->ops->tx_empty(port)) { 1872 msleep_interruptible(jiffies_to_msecs(char_time)); 1873 if (signal_pending(current)) 1874 break; 1875 if (timeout && time_after(jiffies, expire)) 1876 break; 1877 } 1878 uart_port_deref(port); 1879 } 1880 1881 /* 1882 * Calls to uart_hangup() are serialised by the tty_lock in 1883 * drivers/tty/tty_io.c:do_tty_hangup() 1884 * This runs from a workqueue and can sleep for a _short_ time only. 1885 */ 1886 static void uart_hangup(struct tty_struct *tty) 1887 { 1888 struct uart_state *state = tty->driver_data; 1889 struct tty_port *port = &state->port; 1890 struct uart_port *uport; 1891 unsigned long flags; 1892 1893 pr_debug("uart_hangup(%d)\n", tty->index); 1894 1895 mutex_lock(&port->mutex); 1896 uport = uart_port_check(state); 1897 WARN(!uport, "hangup of detached port!\n"); 1898 1899 if (tty_port_active(port)) { 1900 uart_flush_buffer(tty); 1901 uart_shutdown(tty, state); 1902 spin_lock_irqsave(&port->lock, flags); 1903 port->count = 0; 1904 spin_unlock_irqrestore(&port->lock, flags); 1905 tty_port_set_active(port, false); 1906 tty_port_tty_set(port, NULL); 1907 if (uport && !uart_console(uport)) 1908 uart_change_pm(state, UART_PM_STATE_OFF); 1909 wake_up_interruptible(&port->open_wait); 1910 wake_up_interruptible(&port->delta_msr_wait); 1911 } 1912 mutex_unlock(&port->mutex); 1913 } 1914 1915 /* uport == NULL if uart_port has already been removed */ 1916 static void uart_port_shutdown(struct tty_port *port) 1917 { 1918 struct uart_state *state = container_of(port, struct uart_state, port); 1919 struct uart_port *uport = uart_port_check(state); 1920 1921 /* 1922 * clear delta_msr_wait queue to avoid mem leaks: we may free 1923 * the irq here so the queue might never be woken up. Note 1924 * that we won't end up waiting on delta_msr_wait again since 1925 * any outstanding file descriptors should be pointing at 1926 * hung_up_tty_fops now. 1927 */ 1928 wake_up_interruptible(&port->delta_msr_wait); 1929 1930 if (uport) { 1931 /* Free the IRQ and disable the port. */ 1932 uport->ops->shutdown(uport); 1933 1934 /* Ensure that the IRQ handler isn't running on another CPU. */ 1935 synchronize_irq(uport->irq); 1936 } 1937 } 1938 1939 static bool uart_carrier_raised(struct tty_port *port) 1940 { 1941 struct uart_state *state = container_of(port, struct uart_state, port); 1942 struct uart_port *uport; 1943 int mctrl; 1944 1945 uport = uart_port_ref(state); 1946 /* 1947 * Should never observe uport == NULL since checks for hangup should 1948 * abort the tty_port_block_til_ready() loop before checking for carrier 1949 * raised -- but report carrier raised if it does anyway so open will 1950 * continue and not sleep 1951 */ 1952 if (WARN_ON(!uport)) 1953 return true; 1954 uart_port_lock_irq(uport); 1955 uart_enable_ms(uport); 1956 mctrl = uport->ops->get_mctrl(uport); 1957 uart_port_unlock_irq(uport); 1958 uart_port_deref(uport); 1959 1960 return mctrl & TIOCM_CAR; 1961 } 1962 1963 static void uart_dtr_rts(struct tty_port *port, bool active) 1964 { 1965 struct uart_state *state = container_of(port, struct uart_state, port); 1966 struct uart_port *uport; 1967 1968 uport = uart_port_ref(state); 1969 if (!uport) 1970 return; 1971 uart_port_dtr_rts(uport, active); 1972 uart_port_deref(uport); 1973 } 1974 1975 static int uart_install(struct tty_driver *driver, struct tty_struct *tty) 1976 { 1977 struct uart_driver *drv = driver->driver_state; 1978 struct uart_state *state = drv->state + tty->index; 1979 1980 tty->driver_data = state; 1981 1982 return tty_standard_install(driver, tty); 1983 } 1984 1985 /* 1986 * Calls to uart_open are serialised by the tty_lock in 1987 * drivers/tty/tty_io.c:tty_open() 1988 * Note that if this fails, then uart_close() _will_ be called. 1989 * 1990 * In time, we want to scrap the "opening nonpresent ports" 1991 * behaviour and implement an alternative way for setserial 1992 * to set base addresses/ports/types. This will allow us to 1993 * get rid of a certain amount of extra tests. 1994 */ 1995 static int uart_open(struct tty_struct *tty, struct file *filp) 1996 { 1997 struct uart_state *state = tty->driver_data; 1998 int retval; 1999 2000 retval = tty_port_open(&state->port, tty, filp); 2001 if (retval > 0) 2002 retval = 0; 2003 2004 return retval; 2005 } 2006 2007 static int uart_port_activate(struct tty_port *port, struct tty_struct *tty) 2008 { 2009 struct uart_state *state = container_of(port, struct uart_state, port); 2010 struct uart_port *uport; 2011 int ret; 2012 2013 uport = uart_port_check(state); 2014 if (!uport || uport->flags & UPF_DEAD) 2015 return -ENXIO; 2016 2017 /* 2018 * Start up the serial port. 2019 */ 2020 ret = uart_startup(tty, state, false); 2021 if (ret > 0) 2022 tty_port_set_active(port, true); 2023 2024 return ret; 2025 } 2026 2027 static const char *uart_type(struct uart_port *port) 2028 { 2029 const char *str = NULL; 2030 2031 if (port->ops->type) 2032 str = port->ops->type(port); 2033 2034 if (!str) 2035 str = "unknown"; 2036 2037 return str; 2038 } 2039 2040 #ifdef CONFIG_PROC_FS 2041 2042 static void uart_line_info(struct seq_file *m, struct uart_driver *drv, int i) 2043 { 2044 struct uart_state *state = drv->state + i; 2045 struct tty_port *port = &state->port; 2046 enum uart_pm_state pm_state; 2047 struct uart_port *uport; 2048 char stat_buf[32]; 2049 unsigned int status; 2050 int mmio; 2051 2052 mutex_lock(&port->mutex); 2053 uport = uart_port_check(state); 2054 if (!uport) 2055 goto out; 2056 2057 mmio = uport->iotype >= UPIO_MEM; 2058 seq_printf(m, "%d: uart:%s %s%08llX irq:%d", 2059 uport->line, uart_type(uport), 2060 mmio ? "mmio:0x" : "port:", 2061 mmio ? (unsigned long long)uport->mapbase 2062 : (unsigned long long)uport->iobase, 2063 uport->irq); 2064 2065 if (uport->type == PORT_UNKNOWN) { 2066 seq_putc(m, '\n'); 2067 goto out; 2068 } 2069 2070 if (capable(CAP_SYS_ADMIN)) { 2071 pm_state = state->pm_state; 2072 if (pm_state != UART_PM_STATE_ON) 2073 uart_change_pm(state, UART_PM_STATE_ON); 2074 uart_port_lock_irq(uport); 2075 status = uport->ops->get_mctrl(uport); 2076 uart_port_unlock_irq(uport); 2077 if (pm_state != UART_PM_STATE_ON) 2078 uart_change_pm(state, pm_state); 2079 2080 seq_printf(m, " tx:%d rx:%d", 2081 uport->icount.tx, uport->icount.rx); 2082 if (uport->icount.frame) 2083 seq_printf(m, " fe:%d", uport->icount.frame); 2084 if (uport->icount.parity) 2085 seq_printf(m, " pe:%d", uport->icount.parity); 2086 if (uport->icount.brk) 2087 seq_printf(m, " brk:%d", uport->icount.brk); 2088 if (uport->icount.overrun) 2089 seq_printf(m, " oe:%d", uport->icount.overrun); 2090 if (uport->icount.buf_overrun) 2091 seq_printf(m, " bo:%d", uport->icount.buf_overrun); 2092 2093 #define INFOBIT(bit, str) \ 2094 if (uport->mctrl & (bit)) \ 2095 strncat(stat_buf, (str), sizeof(stat_buf) - \ 2096 strlen(stat_buf) - 2) 2097 #define STATBIT(bit, str) \ 2098 if (status & (bit)) \ 2099 strncat(stat_buf, (str), sizeof(stat_buf) - \ 2100 strlen(stat_buf) - 2) 2101 2102 stat_buf[0] = '\0'; 2103 stat_buf[1] = '\0'; 2104 INFOBIT(TIOCM_RTS, "|RTS"); 2105 STATBIT(TIOCM_CTS, "|CTS"); 2106 INFOBIT(TIOCM_DTR, "|DTR"); 2107 STATBIT(TIOCM_DSR, "|DSR"); 2108 STATBIT(TIOCM_CAR, "|CD"); 2109 STATBIT(TIOCM_RNG, "|RI"); 2110 if (stat_buf[0]) 2111 stat_buf[0] = ' '; 2112 2113 seq_puts(m, stat_buf); 2114 } 2115 seq_putc(m, '\n'); 2116 #undef STATBIT 2117 #undef INFOBIT 2118 out: 2119 mutex_unlock(&port->mutex); 2120 } 2121 2122 static int uart_proc_show(struct seq_file *m, void *v) 2123 { 2124 struct tty_driver *ttydrv = m->private; 2125 struct uart_driver *drv = ttydrv->driver_state; 2126 int i; 2127 2128 seq_printf(m, "serinfo:1.0 driver%s%s revision:%s\n", "", "", ""); 2129 for (i = 0; i < drv->nr; i++) 2130 uart_line_info(m, drv, i); 2131 return 0; 2132 } 2133 #endif 2134 2135 static void uart_port_spin_lock_init(struct uart_port *port) 2136 { 2137 spin_lock_init(&port->lock); 2138 lockdep_set_class(&port->lock, &port_lock_key); 2139 } 2140 2141 #if defined(CONFIG_SERIAL_CORE_CONSOLE) || defined(CONFIG_CONSOLE_POLL) 2142 /** 2143 * uart_console_write - write a console message to a serial port 2144 * @port: the port to write the message 2145 * @s: array of characters 2146 * @count: number of characters in string to write 2147 * @putchar: function to write character to port 2148 */ 2149 void uart_console_write(struct uart_port *port, const char *s, 2150 unsigned int count, 2151 void (*putchar)(struct uart_port *, unsigned char)) 2152 { 2153 unsigned int i; 2154 2155 for (i = 0; i < count; i++, s++) { 2156 if (*s == '\n') 2157 putchar(port, '\r'); 2158 putchar(port, *s); 2159 } 2160 } 2161 EXPORT_SYMBOL_GPL(uart_console_write); 2162 2163 /** 2164 * uart_get_console - get uart port for console 2165 * @ports: ports to search in 2166 * @nr: number of @ports 2167 * @co: console to search for 2168 * Returns: uart_port for the console @co 2169 * 2170 * Check whether an invalid uart number has been specified (as @co->index), and 2171 * if so, search for the first available port that does have console support. 2172 */ 2173 struct uart_port * __init 2174 uart_get_console(struct uart_port *ports, int nr, struct console *co) 2175 { 2176 int idx = co->index; 2177 2178 if (idx < 0 || idx >= nr || (ports[idx].iobase == 0 && 2179 ports[idx].membase == NULL)) 2180 for (idx = 0; idx < nr; idx++) 2181 if (ports[idx].iobase != 0 || 2182 ports[idx].membase != NULL) 2183 break; 2184 2185 co->index = idx; 2186 2187 return ports + idx; 2188 } 2189 2190 /** 2191 * uart_parse_earlycon - Parse earlycon options 2192 * @p: ptr to 2nd field (ie., just beyond '<name>,') 2193 * @iotype: ptr for decoded iotype (out) 2194 * @addr: ptr for decoded mapbase/iobase (out) 2195 * @options: ptr for <options> field; %NULL if not present (out) 2196 * 2197 * Decodes earlycon kernel command line parameters of the form: 2198 * * earlycon=<name>,io|mmio|mmio16|mmio32|mmio32be|mmio32native,<addr>,<options> 2199 * * console=<name>,io|mmio|mmio16|mmio32|mmio32be|mmio32native,<addr>,<options> 2200 * 2201 * The optional form: 2202 * * earlycon=<name>,0x<addr>,<options> 2203 * * console=<name>,0x<addr>,<options> 2204 * 2205 * is also accepted; the returned @iotype will be %UPIO_MEM. 2206 * 2207 * Returns: 0 on success or -%EINVAL on failure 2208 */ 2209 int uart_parse_earlycon(char *p, unsigned char *iotype, resource_size_t *addr, 2210 char **options) 2211 { 2212 if (strncmp(p, "mmio,", 5) == 0) { 2213 *iotype = UPIO_MEM; 2214 p += 5; 2215 } else if (strncmp(p, "mmio16,", 7) == 0) { 2216 *iotype = UPIO_MEM16; 2217 p += 7; 2218 } else if (strncmp(p, "mmio32,", 7) == 0) { 2219 *iotype = UPIO_MEM32; 2220 p += 7; 2221 } else if (strncmp(p, "mmio32be,", 9) == 0) { 2222 *iotype = UPIO_MEM32BE; 2223 p += 9; 2224 } else if (strncmp(p, "mmio32native,", 13) == 0) { 2225 *iotype = IS_ENABLED(CONFIG_CPU_BIG_ENDIAN) ? 2226 UPIO_MEM32BE : UPIO_MEM32; 2227 p += 13; 2228 } else if (strncmp(p, "io,", 3) == 0) { 2229 *iotype = UPIO_PORT; 2230 p += 3; 2231 } else if (strncmp(p, "0x", 2) == 0) { 2232 *iotype = UPIO_MEM; 2233 } else { 2234 return -EINVAL; 2235 } 2236 2237 /* 2238 * Before you replace it with kstrtoull(), think about options separator 2239 * (',') it will not tolerate 2240 */ 2241 *addr = simple_strtoull(p, NULL, 0); 2242 p = strchr(p, ','); 2243 if (p) 2244 p++; 2245 2246 *options = p; 2247 return 0; 2248 } 2249 EXPORT_SYMBOL_GPL(uart_parse_earlycon); 2250 2251 /** 2252 * uart_parse_options - Parse serial port baud/parity/bits/flow control. 2253 * @options: pointer to option string 2254 * @baud: pointer to an 'int' variable for the baud rate. 2255 * @parity: pointer to an 'int' variable for the parity. 2256 * @bits: pointer to an 'int' variable for the number of data bits. 2257 * @flow: pointer to an 'int' variable for the flow control character. 2258 * 2259 * uart_parse_options() decodes a string containing the serial console 2260 * options. The format of the string is <baud><parity><bits><flow>, 2261 * eg: 115200n8r 2262 */ 2263 void 2264 uart_parse_options(const char *options, int *baud, int *parity, 2265 int *bits, int *flow) 2266 { 2267 const char *s = options; 2268 2269 *baud = simple_strtoul(s, NULL, 10); 2270 while (*s >= '0' && *s <= '9') 2271 s++; 2272 if (*s) 2273 *parity = *s++; 2274 if (*s) 2275 *bits = *s++ - '0'; 2276 if (*s) 2277 *flow = *s; 2278 } 2279 EXPORT_SYMBOL_GPL(uart_parse_options); 2280 2281 /** 2282 * uart_set_options - setup the serial console parameters 2283 * @port: pointer to the serial ports uart_port structure 2284 * @co: console pointer 2285 * @baud: baud rate 2286 * @parity: parity character - 'n' (none), 'o' (odd), 'e' (even) 2287 * @bits: number of data bits 2288 * @flow: flow control character - 'r' (rts) 2289 * 2290 * Locking: Caller must hold console_list_lock in order to serialize 2291 * early initialization of the serial-console lock. 2292 */ 2293 int 2294 uart_set_options(struct uart_port *port, struct console *co, 2295 int baud, int parity, int bits, int flow) 2296 { 2297 struct ktermios termios; 2298 static struct ktermios dummy; 2299 2300 /* 2301 * Ensure that the serial-console lock is initialised early. 2302 * 2303 * Note that the console-registered check is needed because 2304 * kgdboc can call uart_set_options() for an already registered 2305 * console via tty_find_polling_driver() and uart_poll_init(). 2306 */ 2307 if (!uart_console_registered_locked(port) && !port->console_reinit) 2308 uart_port_spin_lock_init(port); 2309 2310 memset(&termios, 0, sizeof(struct ktermios)); 2311 2312 termios.c_cflag |= CREAD | HUPCL | CLOCAL; 2313 tty_termios_encode_baud_rate(&termios, baud, baud); 2314 2315 if (bits == 7) 2316 termios.c_cflag |= CS7; 2317 else 2318 termios.c_cflag |= CS8; 2319 2320 switch (parity) { 2321 case 'o': case 'O': 2322 termios.c_cflag |= PARODD; 2323 fallthrough; 2324 case 'e': case 'E': 2325 termios.c_cflag |= PARENB; 2326 break; 2327 } 2328 2329 if (flow == 'r') 2330 termios.c_cflag |= CRTSCTS; 2331 2332 /* 2333 * some uarts on other side don't support no flow control. 2334 * So we set * DTR in host uart to make them happy 2335 */ 2336 port->mctrl |= TIOCM_DTR; 2337 2338 port->ops->set_termios(port, &termios, &dummy); 2339 /* 2340 * Allow the setting of the UART parameters with a NULL console 2341 * too: 2342 */ 2343 if (co) { 2344 co->cflag = termios.c_cflag; 2345 co->ispeed = termios.c_ispeed; 2346 co->ospeed = termios.c_ospeed; 2347 } 2348 2349 return 0; 2350 } 2351 EXPORT_SYMBOL_GPL(uart_set_options); 2352 #endif /* CONFIG_SERIAL_CORE_CONSOLE */ 2353 2354 /** 2355 * uart_change_pm - set power state of the port 2356 * 2357 * @state: port descriptor 2358 * @pm_state: new state 2359 * 2360 * Locking: port->mutex has to be held 2361 */ 2362 static void uart_change_pm(struct uart_state *state, 2363 enum uart_pm_state pm_state) 2364 { 2365 struct uart_port *port = uart_port_check(state); 2366 2367 if (state->pm_state != pm_state) { 2368 if (port && port->ops->pm) 2369 port->ops->pm(port, pm_state, state->pm_state); 2370 state->pm_state = pm_state; 2371 } 2372 } 2373 2374 struct uart_match { 2375 struct uart_port *port; 2376 struct uart_driver *driver; 2377 }; 2378 2379 static int serial_match_port(struct device *dev, void *data) 2380 { 2381 struct uart_match *match = data; 2382 struct tty_driver *tty_drv = match->driver->tty_driver; 2383 dev_t devt = MKDEV(tty_drv->major, tty_drv->minor_start) + 2384 match->port->line; 2385 2386 return dev->devt == devt; /* Actually, only one tty per port */ 2387 } 2388 2389 int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport) 2390 { 2391 struct uart_state *state = drv->state + uport->line; 2392 struct tty_port *port = &state->port; 2393 struct device *tty_dev; 2394 struct uart_match match = {uport, drv}; 2395 2396 mutex_lock(&port->mutex); 2397 2398 tty_dev = device_find_child(&uport->port_dev->dev, &match, serial_match_port); 2399 if (tty_dev && device_may_wakeup(tty_dev)) { 2400 enable_irq_wake(uport->irq); 2401 put_device(tty_dev); 2402 mutex_unlock(&port->mutex); 2403 return 0; 2404 } 2405 put_device(tty_dev); 2406 2407 /* 2408 * Nothing to do if the console is not suspending 2409 * except stop_rx to prevent any asynchronous data 2410 * over RX line. However ensure that we will be 2411 * able to Re-start_rx later. 2412 */ 2413 if (!console_suspend_enabled && uart_console(uport)) { 2414 if (uport->ops->start_rx) { 2415 uart_port_lock_irq(uport); 2416 uport->ops->stop_rx(uport); 2417 uart_port_unlock_irq(uport); 2418 } 2419 device_set_awake_path(uport->dev); 2420 goto unlock; 2421 } 2422 2423 uport->suspended = 1; 2424 2425 if (tty_port_initialized(port)) { 2426 const struct uart_ops *ops = uport->ops; 2427 int tries; 2428 unsigned int mctrl; 2429 2430 tty_port_set_suspended(port, true); 2431 tty_port_set_initialized(port, false); 2432 2433 uart_port_lock_irq(uport); 2434 ops->stop_tx(uport); 2435 if (!(uport->rs485.flags & SER_RS485_ENABLED)) 2436 ops->set_mctrl(uport, 0); 2437 /* save mctrl so it can be restored on resume */ 2438 mctrl = uport->mctrl; 2439 uport->mctrl = 0; 2440 ops->stop_rx(uport); 2441 uart_port_unlock_irq(uport); 2442 2443 /* 2444 * Wait for the transmitter to empty. 2445 */ 2446 for (tries = 3; !ops->tx_empty(uport) && tries; tries--) 2447 msleep(10); 2448 if (!tries) 2449 dev_err(uport->dev, "%s: Unable to drain transmitter\n", 2450 uport->name); 2451 2452 ops->shutdown(uport); 2453 uport->mctrl = mctrl; 2454 } 2455 2456 /* 2457 * Disable the console device before suspending. 2458 */ 2459 if (uart_console(uport)) 2460 console_stop(uport->cons); 2461 2462 uart_change_pm(state, UART_PM_STATE_OFF); 2463 unlock: 2464 mutex_unlock(&port->mutex); 2465 2466 return 0; 2467 } 2468 EXPORT_SYMBOL(uart_suspend_port); 2469 2470 int uart_resume_port(struct uart_driver *drv, struct uart_port *uport) 2471 { 2472 struct uart_state *state = drv->state + uport->line; 2473 struct tty_port *port = &state->port; 2474 struct device *tty_dev; 2475 struct uart_match match = {uport, drv}; 2476 struct ktermios termios; 2477 2478 mutex_lock(&port->mutex); 2479 2480 tty_dev = device_find_child(&uport->port_dev->dev, &match, serial_match_port); 2481 if (!uport->suspended && device_may_wakeup(tty_dev)) { 2482 if (irqd_is_wakeup_set(irq_get_irq_data((uport->irq)))) 2483 disable_irq_wake(uport->irq); 2484 put_device(tty_dev); 2485 mutex_unlock(&port->mutex); 2486 return 0; 2487 } 2488 put_device(tty_dev); 2489 uport->suspended = 0; 2490 2491 /* 2492 * Re-enable the console device after suspending. 2493 */ 2494 if (uart_console(uport)) { 2495 /* 2496 * First try to use the console cflag setting. 2497 */ 2498 memset(&termios, 0, sizeof(struct ktermios)); 2499 termios.c_cflag = uport->cons->cflag; 2500 termios.c_ispeed = uport->cons->ispeed; 2501 termios.c_ospeed = uport->cons->ospeed; 2502 2503 /* 2504 * If that's unset, use the tty termios setting. 2505 */ 2506 if (port->tty && termios.c_cflag == 0) 2507 termios = port->tty->termios; 2508 2509 if (console_suspend_enabled) 2510 uart_change_pm(state, UART_PM_STATE_ON); 2511 uport->ops->set_termios(uport, &termios, NULL); 2512 if (!console_suspend_enabled && uport->ops->start_rx) { 2513 uart_port_lock_irq(uport); 2514 uport->ops->start_rx(uport); 2515 uart_port_unlock_irq(uport); 2516 } 2517 if (console_suspend_enabled) 2518 console_start(uport->cons); 2519 } 2520 2521 if (tty_port_suspended(port)) { 2522 const struct uart_ops *ops = uport->ops; 2523 int ret; 2524 2525 uart_change_pm(state, UART_PM_STATE_ON); 2526 uart_port_lock_irq(uport); 2527 if (!(uport->rs485.flags & SER_RS485_ENABLED)) 2528 ops->set_mctrl(uport, 0); 2529 uart_port_unlock_irq(uport); 2530 if (console_suspend_enabled || !uart_console(uport)) { 2531 /* Protected by port mutex for now */ 2532 struct tty_struct *tty = port->tty; 2533 2534 ret = ops->startup(uport); 2535 if (ret == 0) { 2536 if (tty) 2537 uart_change_line_settings(tty, state, NULL); 2538 uart_rs485_config(uport); 2539 uart_port_lock_irq(uport); 2540 if (!(uport->rs485.flags & SER_RS485_ENABLED)) 2541 ops->set_mctrl(uport, uport->mctrl); 2542 ops->start_tx(uport); 2543 uart_port_unlock_irq(uport); 2544 tty_port_set_initialized(port, true); 2545 } else { 2546 /* 2547 * Failed to resume - maybe hardware went away? 2548 * Clear the "initialized" flag so we won't try 2549 * to call the low level drivers shutdown method. 2550 */ 2551 uart_shutdown(tty, state); 2552 } 2553 } 2554 2555 tty_port_set_suspended(port, false); 2556 } 2557 2558 mutex_unlock(&port->mutex); 2559 2560 return 0; 2561 } 2562 EXPORT_SYMBOL(uart_resume_port); 2563 2564 static inline void 2565 uart_report_port(struct uart_driver *drv, struct uart_port *port) 2566 { 2567 char address[64]; 2568 2569 switch (port->iotype) { 2570 case UPIO_PORT: 2571 snprintf(address, sizeof(address), "I/O 0x%lx", port->iobase); 2572 break; 2573 case UPIO_HUB6: 2574 snprintf(address, sizeof(address), 2575 "I/O 0x%lx offset 0x%x", port->iobase, port->hub6); 2576 break; 2577 case UPIO_MEM: 2578 case UPIO_MEM16: 2579 case UPIO_MEM32: 2580 case UPIO_MEM32BE: 2581 case UPIO_AU: 2582 case UPIO_TSI: 2583 snprintf(address, sizeof(address), 2584 "MMIO 0x%llx", (unsigned long long)port->mapbase); 2585 break; 2586 default: 2587 strscpy(address, "*unknown*", sizeof(address)); 2588 break; 2589 } 2590 2591 pr_info("%s%s%s at %s (irq = %d, base_baud = %d) is a %s\n", 2592 port->dev ? dev_name(port->dev) : "", 2593 port->dev ? ": " : "", 2594 port->name, 2595 address, port->irq, port->uartclk / 16, uart_type(port)); 2596 2597 /* The magic multiplier feature is a bit obscure, so report it too. */ 2598 if (port->flags & UPF_MAGIC_MULTIPLIER) 2599 pr_info("%s%s%s extra baud rates supported: %d, %d", 2600 port->dev ? dev_name(port->dev) : "", 2601 port->dev ? ": " : "", 2602 port->name, 2603 port->uartclk / 8, port->uartclk / 4); 2604 } 2605 2606 static void 2607 uart_configure_port(struct uart_driver *drv, struct uart_state *state, 2608 struct uart_port *port) 2609 { 2610 unsigned int flags; 2611 2612 /* 2613 * If there isn't a port here, don't do anything further. 2614 */ 2615 if (!port->iobase && !port->mapbase && !port->membase) 2616 return; 2617 2618 /* 2619 * Now do the auto configuration stuff. Note that config_port 2620 * is expected to claim the resources and map the port for us. 2621 */ 2622 flags = 0; 2623 if (port->flags & UPF_AUTO_IRQ) 2624 flags |= UART_CONFIG_IRQ; 2625 if (port->flags & UPF_BOOT_AUTOCONF) { 2626 if (!(port->flags & UPF_FIXED_TYPE)) { 2627 port->type = PORT_UNKNOWN; 2628 flags |= UART_CONFIG_TYPE; 2629 } 2630 /* Synchronize with possible boot console. */ 2631 if (uart_console(port)) 2632 console_lock(); 2633 port->ops->config_port(port, flags); 2634 if (uart_console(port)) 2635 console_unlock(); 2636 } 2637 2638 if (port->type != PORT_UNKNOWN) { 2639 unsigned long flags; 2640 2641 uart_report_port(drv, port); 2642 2643 /* Synchronize with possible boot console. */ 2644 if (uart_console(port)) 2645 console_lock(); 2646 2647 /* Power up port for set_mctrl() */ 2648 uart_change_pm(state, UART_PM_STATE_ON); 2649 2650 /* 2651 * Ensure that the modem control lines are de-activated. 2652 * keep the DTR setting that is set in uart_set_options() 2653 * We probably don't need a spinlock around this, but 2654 */ 2655 uart_port_lock_irqsave(port, &flags); 2656 port->mctrl &= TIOCM_DTR; 2657 if (!(port->rs485.flags & SER_RS485_ENABLED)) 2658 port->ops->set_mctrl(port, port->mctrl); 2659 uart_port_unlock_irqrestore(port, flags); 2660 2661 uart_rs485_config(port); 2662 2663 if (uart_console(port)) 2664 console_unlock(); 2665 2666 /* 2667 * If this driver supports console, and it hasn't been 2668 * successfully registered yet, try to re-register it. 2669 * It may be that the port was not available. 2670 */ 2671 if (port->cons && !console_is_registered(port->cons)) 2672 register_console(port->cons); 2673 2674 /* 2675 * Power down all ports by default, except the 2676 * console if we have one. 2677 */ 2678 if (!uart_console(port)) 2679 uart_change_pm(state, UART_PM_STATE_OFF); 2680 } 2681 } 2682 2683 #ifdef CONFIG_CONSOLE_POLL 2684 2685 static int uart_poll_init(struct tty_driver *driver, int line, char *options) 2686 { 2687 struct uart_driver *drv = driver->driver_state; 2688 struct uart_state *state = drv->state + line; 2689 enum uart_pm_state pm_state; 2690 struct tty_port *tport; 2691 struct uart_port *port; 2692 int baud = 9600; 2693 int bits = 8; 2694 int parity = 'n'; 2695 int flow = 'n'; 2696 int ret = 0; 2697 2698 tport = &state->port; 2699 mutex_lock(&tport->mutex); 2700 2701 port = uart_port_check(state); 2702 if (!port || port->type == PORT_UNKNOWN || 2703 !(port->ops->poll_get_char && port->ops->poll_put_char)) { 2704 ret = -1; 2705 goto out; 2706 } 2707 2708 pm_state = state->pm_state; 2709 uart_change_pm(state, UART_PM_STATE_ON); 2710 2711 if (port->ops->poll_init) { 2712 /* 2713 * We don't set initialized as we only initialized the hw, 2714 * e.g. state->xmit is still uninitialized. 2715 */ 2716 if (!tty_port_initialized(tport)) 2717 ret = port->ops->poll_init(port); 2718 } 2719 2720 if (!ret && options) { 2721 uart_parse_options(options, &baud, &parity, &bits, &flow); 2722 console_list_lock(); 2723 ret = uart_set_options(port, NULL, baud, parity, bits, flow); 2724 console_list_unlock(); 2725 } 2726 out: 2727 if (ret) 2728 uart_change_pm(state, pm_state); 2729 mutex_unlock(&tport->mutex); 2730 return ret; 2731 } 2732 2733 static int uart_poll_get_char(struct tty_driver *driver, int line) 2734 { 2735 struct uart_driver *drv = driver->driver_state; 2736 struct uart_state *state = drv->state + line; 2737 struct uart_port *port; 2738 int ret = -1; 2739 2740 port = uart_port_ref(state); 2741 if (port) { 2742 ret = port->ops->poll_get_char(port); 2743 uart_port_deref(port); 2744 } 2745 2746 return ret; 2747 } 2748 2749 static void uart_poll_put_char(struct tty_driver *driver, int line, char ch) 2750 { 2751 struct uart_driver *drv = driver->driver_state; 2752 struct uart_state *state = drv->state + line; 2753 struct uart_port *port; 2754 2755 port = uart_port_ref(state); 2756 if (!port) 2757 return; 2758 2759 if (ch == '\n') 2760 port->ops->poll_put_char(port, '\r'); 2761 port->ops->poll_put_char(port, ch); 2762 uart_port_deref(port); 2763 } 2764 #endif 2765 2766 static const struct tty_operations uart_ops = { 2767 .install = uart_install, 2768 .open = uart_open, 2769 .close = uart_close, 2770 .write = uart_write, 2771 .put_char = uart_put_char, 2772 .flush_chars = uart_flush_chars, 2773 .write_room = uart_write_room, 2774 .chars_in_buffer= uart_chars_in_buffer, 2775 .flush_buffer = uart_flush_buffer, 2776 .ioctl = uart_ioctl, 2777 .throttle = uart_throttle, 2778 .unthrottle = uart_unthrottle, 2779 .send_xchar = uart_send_xchar, 2780 .set_termios = uart_set_termios, 2781 .set_ldisc = uart_set_ldisc, 2782 .stop = uart_stop, 2783 .start = uart_start, 2784 .hangup = uart_hangup, 2785 .break_ctl = uart_break_ctl, 2786 .wait_until_sent= uart_wait_until_sent, 2787 #ifdef CONFIG_PROC_FS 2788 .proc_show = uart_proc_show, 2789 #endif 2790 .tiocmget = uart_tiocmget, 2791 .tiocmset = uart_tiocmset, 2792 .set_serial = uart_set_info_user, 2793 .get_serial = uart_get_info_user, 2794 .get_icount = uart_get_icount, 2795 #ifdef CONFIG_CONSOLE_POLL 2796 .poll_init = uart_poll_init, 2797 .poll_get_char = uart_poll_get_char, 2798 .poll_put_char = uart_poll_put_char, 2799 #endif 2800 }; 2801 2802 static const struct tty_port_operations uart_port_ops = { 2803 .carrier_raised = uart_carrier_raised, 2804 .dtr_rts = uart_dtr_rts, 2805 .activate = uart_port_activate, 2806 .shutdown = uart_tty_port_shutdown, 2807 }; 2808 2809 /** 2810 * uart_register_driver - register a driver with the uart core layer 2811 * @drv: low level driver structure 2812 * 2813 * Register a uart driver with the core driver. We in turn register with the 2814 * tty layer, and initialise the core driver per-port state. 2815 * 2816 * We have a proc file in /proc/tty/driver which is named after the normal 2817 * driver. 2818 * 2819 * @drv->port should be %NULL, and the per-port structures should be registered 2820 * using uart_add_one_port() after this call has succeeded. 2821 * 2822 * Locking: none, Interrupts: enabled 2823 */ 2824 int uart_register_driver(struct uart_driver *drv) 2825 { 2826 struct tty_driver *normal; 2827 int i, retval = -ENOMEM; 2828 2829 BUG_ON(drv->state); 2830 2831 /* 2832 * Maybe we should be using a slab cache for this, especially if 2833 * we have a large number of ports to handle. 2834 */ 2835 drv->state = kcalloc(drv->nr, sizeof(struct uart_state), GFP_KERNEL); 2836 if (!drv->state) 2837 goto out; 2838 2839 normal = tty_alloc_driver(drv->nr, TTY_DRIVER_REAL_RAW | 2840 TTY_DRIVER_DYNAMIC_DEV); 2841 if (IS_ERR(normal)) { 2842 retval = PTR_ERR(normal); 2843 goto out_kfree; 2844 } 2845 2846 drv->tty_driver = normal; 2847 2848 normal->driver_name = drv->driver_name; 2849 normal->name = drv->dev_name; 2850 normal->major = drv->major; 2851 normal->minor_start = drv->minor; 2852 normal->type = TTY_DRIVER_TYPE_SERIAL; 2853 normal->subtype = SERIAL_TYPE_NORMAL; 2854 normal->init_termios = tty_std_termios; 2855 normal->init_termios.c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL; 2856 normal->init_termios.c_ispeed = normal->init_termios.c_ospeed = 9600; 2857 normal->driver_state = drv; 2858 tty_set_operations(normal, &uart_ops); 2859 2860 /* 2861 * Initialise the UART state(s). 2862 */ 2863 for (i = 0; i < drv->nr; i++) { 2864 struct uart_state *state = drv->state + i; 2865 struct tty_port *port = &state->port; 2866 2867 tty_port_init(port); 2868 port->ops = &uart_port_ops; 2869 } 2870 2871 retval = tty_register_driver(normal); 2872 if (retval >= 0) 2873 return retval; 2874 2875 for (i = 0; i < drv->nr; i++) 2876 tty_port_destroy(&drv->state[i].port); 2877 tty_driver_kref_put(normal); 2878 out_kfree: 2879 kfree(drv->state); 2880 out: 2881 return retval; 2882 } 2883 EXPORT_SYMBOL(uart_register_driver); 2884 2885 /** 2886 * uart_unregister_driver - remove a driver from the uart core layer 2887 * @drv: low level driver structure 2888 * 2889 * Remove all references to a driver from the core driver. The low level 2890 * driver must have removed all its ports via the uart_remove_one_port() if it 2891 * registered them with uart_add_one_port(). (I.e. @drv->port is %NULL.) 2892 * 2893 * Locking: none, Interrupts: enabled 2894 */ 2895 void uart_unregister_driver(struct uart_driver *drv) 2896 { 2897 struct tty_driver *p = drv->tty_driver; 2898 unsigned int i; 2899 2900 tty_unregister_driver(p); 2901 tty_driver_kref_put(p); 2902 for (i = 0; i < drv->nr; i++) 2903 tty_port_destroy(&drv->state[i].port); 2904 kfree(drv->state); 2905 drv->state = NULL; 2906 drv->tty_driver = NULL; 2907 } 2908 EXPORT_SYMBOL(uart_unregister_driver); 2909 2910 struct tty_driver *uart_console_device(struct console *co, int *index) 2911 { 2912 struct uart_driver *p = co->data; 2913 *index = co->index; 2914 return p->tty_driver; 2915 } 2916 EXPORT_SYMBOL_GPL(uart_console_device); 2917 2918 static ssize_t uartclk_show(struct device *dev, 2919 struct device_attribute *attr, char *buf) 2920 { 2921 struct serial_struct tmp; 2922 struct tty_port *port = dev_get_drvdata(dev); 2923 2924 uart_get_info(port, &tmp); 2925 return sprintf(buf, "%d\n", tmp.baud_base * 16); 2926 } 2927 2928 static ssize_t type_show(struct device *dev, 2929 struct device_attribute *attr, char *buf) 2930 { 2931 struct serial_struct tmp; 2932 struct tty_port *port = dev_get_drvdata(dev); 2933 2934 uart_get_info(port, &tmp); 2935 return sprintf(buf, "%d\n", tmp.type); 2936 } 2937 2938 static ssize_t line_show(struct device *dev, 2939 struct device_attribute *attr, char *buf) 2940 { 2941 struct serial_struct tmp; 2942 struct tty_port *port = dev_get_drvdata(dev); 2943 2944 uart_get_info(port, &tmp); 2945 return sprintf(buf, "%d\n", tmp.line); 2946 } 2947 2948 static ssize_t port_show(struct device *dev, 2949 struct device_attribute *attr, char *buf) 2950 { 2951 struct serial_struct tmp; 2952 struct tty_port *port = dev_get_drvdata(dev); 2953 unsigned long ioaddr; 2954 2955 uart_get_info(port, &tmp); 2956 ioaddr = tmp.port; 2957 if (HIGH_BITS_OFFSET) 2958 ioaddr |= (unsigned long)tmp.port_high << HIGH_BITS_OFFSET; 2959 return sprintf(buf, "0x%lX\n", ioaddr); 2960 } 2961 2962 static ssize_t irq_show(struct device *dev, 2963 struct device_attribute *attr, char *buf) 2964 { 2965 struct serial_struct tmp; 2966 struct tty_port *port = dev_get_drvdata(dev); 2967 2968 uart_get_info(port, &tmp); 2969 return sprintf(buf, "%d\n", tmp.irq); 2970 } 2971 2972 static ssize_t flags_show(struct device *dev, 2973 struct device_attribute *attr, char *buf) 2974 { 2975 struct serial_struct tmp; 2976 struct tty_port *port = dev_get_drvdata(dev); 2977 2978 uart_get_info(port, &tmp); 2979 return sprintf(buf, "0x%X\n", tmp.flags); 2980 } 2981 2982 static ssize_t xmit_fifo_size_show(struct device *dev, 2983 struct device_attribute *attr, char *buf) 2984 { 2985 struct serial_struct tmp; 2986 struct tty_port *port = dev_get_drvdata(dev); 2987 2988 uart_get_info(port, &tmp); 2989 return sprintf(buf, "%d\n", tmp.xmit_fifo_size); 2990 } 2991 2992 static ssize_t close_delay_show(struct device *dev, 2993 struct device_attribute *attr, char *buf) 2994 { 2995 struct serial_struct tmp; 2996 struct tty_port *port = dev_get_drvdata(dev); 2997 2998 uart_get_info(port, &tmp); 2999 return sprintf(buf, "%d\n", tmp.close_delay); 3000 } 3001 3002 static ssize_t closing_wait_show(struct device *dev, 3003 struct device_attribute *attr, char *buf) 3004 { 3005 struct serial_struct tmp; 3006 struct tty_port *port = dev_get_drvdata(dev); 3007 3008 uart_get_info(port, &tmp); 3009 return sprintf(buf, "%d\n", tmp.closing_wait); 3010 } 3011 3012 static ssize_t custom_divisor_show(struct device *dev, 3013 struct device_attribute *attr, char *buf) 3014 { 3015 struct serial_struct tmp; 3016 struct tty_port *port = dev_get_drvdata(dev); 3017 3018 uart_get_info(port, &tmp); 3019 return sprintf(buf, "%d\n", tmp.custom_divisor); 3020 } 3021 3022 static ssize_t io_type_show(struct device *dev, 3023 struct device_attribute *attr, char *buf) 3024 { 3025 struct serial_struct tmp; 3026 struct tty_port *port = dev_get_drvdata(dev); 3027 3028 uart_get_info(port, &tmp); 3029 return sprintf(buf, "%d\n", tmp.io_type); 3030 } 3031 3032 static ssize_t iomem_base_show(struct device *dev, 3033 struct device_attribute *attr, char *buf) 3034 { 3035 struct serial_struct tmp; 3036 struct tty_port *port = dev_get_drvdata(dev); 3037 3038 uart_get_info(port, &tmp); 3039 return sprintf(buf, "0x%lX\n", (unsigned long)tmp.iomem_base); 3040 } 3041 3042 static ssize_t iomem_reg_shift_show(struct device *dev, 3043 struct device_attribute *attr, char *buf) 3044 { 3045 struct serial_struct tmp; 3046 struct tty_port *port = dev_get_drvdata(dev); 3047 3048 uart_get_info(port, &tmp); 3049 return sprintf(buf, "%d\n", tmp.iomem_reg_shift); 3050 } 3051 3052 static ssize_t console_show(struct device *dev, 3053 struct device_attribute *attr, char *buf) 3054 { 3055 struct tty_port *port = dev_get_drvdata(dev); 3056 struct uart_state *state = container_of(port, struct uart_state, port); 3057 struct uart_port *uport; 3058 bool console = false; 3059 3060 mutex_lock(&port->mutex); 3061 uport = uart_port_check(state); 3062 if (uport) 3063 console = uart_console_registered(uport); 3064 mutex_unlock(&port->mutex); 3065 3066 return sprintf(buf, "%c\n", console ? 'Y' : 'N'); 3067 } 3068 3069 static ssize_t console_store(struct device *dev, 3070 struct device_attribute *attr, const char *buf, size_t count) 3071 { 3072 struct tty_port *port = dev_get_drvdata(dev); 3073 struct uart_state *state = container_of(port, struct uart_state, port); 3074 struct uart_port *uport; 3075 bool oldconsole, newconsole; 3076 int ret; 3077 3078 ret = kstrtobool(buf, &newconsole); 3079 if (ret) 3080 return ret; 3081 3082 mutex_lock(&port->mutex); 3083 uport = uart_port_check(state); 3084 if (uport) { 3085 oldconsole = uart_console_registered(uport); 3086 if (oldconsole && !newconsole) { 3087 ret = unregister_console(uport->cons); 3088 } else if (!oldconsole && newconsole) { 3089 if (uart_console(uport)) { 3090 uport->console_reinit = 1; 3091 register_console(uport->cons); 3092 } else { 3093 ret = -ENOENT; 3094 } 3095 } 3096 } else { 3097 ret = -ENXIO; 3098 } 3099 mutex_unlock(&port->mutex); 3100 3101 return ret < 0 ? ret : count; 3102 } 3103 3104 static DEVICE_ATTR_RO(uartclk); 3105 static DEVICE_ATTR_RO(type); 3106 static DEVICE_ATTR_RO(line); 3107 static DEVICE_ATTR_RO(port); 3108 static DEVICE_ATTR_RO(irq); 3109 static DEVICE_ATTR_RO(flags); 3110 static DEVICE_ATTR_RO(xmit_fifo_size); 3111 static DEVICE_ATTR_RO(close_delay); 3112 static DEVICE_ATTR_RO(closing_wait); 3113 static DEVICE_ATTR_RO(custom_divisor); 3114 static DEVICE_ATTR_RO(io_type); 3115 static DEVICE_ATTR_RO(iomem_base); 3116 static DEVICE_ATTR_RO(iomem_reg_shift); 3117 static DEVICE_ATTR_RW(console); 3118 3119 static struct attribute *tty_dev_attrs[] = { 3120 &dev_attr_uartclk.attr, 3121 &dev_attr_type.attr, 3122 &dev_attr_line.attr, 3123 &dev_attr_port.attr, 3124 &dev_attr_irq.attr, 3125 &dev_attr_flags.attr, 3126 &dev_attr_xmit_fifo_size.attr, 3127 &dev_attr_close_delay.attr, 3128 &dev_attr_closing_wait.attr, 3129 &dev_attr_custom_divisor.attr, 3130 &dev_attr_io_type.attr, 3131 &dev_attr_iomem_base.attr, 3132 &dev_attr_iomem_reg_shift.attr, 3133 &dev_attr_console.attr, 3134 NULL 3135 }; 3136 3137 static const struct attribute_group tty_dev_attr_group = { 3138 .attrs = tty_dev_attrs, 3139 }; 3140 3141 /** 3142 * serial_core_add_one_port - attach a driver-defined port structure 3143 * @drv: pointer to the uart low level driver structure for this port 3144 * @uport: uart port structure to use for this port. 3145 * 3146 * Context: task context, might sleep 3147 * 3148 * This allows the driver @drv to register its own uart_port structure with the 3149 * core driver. The main purpose is to allow the low level uart drivers to 3150 * expand uart_port, rather than having yet more levels of structures. 3151 * Caller must hold port_mutex. 3152 */ 3153 static int serial_core_add_one_port(struct uart_driver *drv, struct uart_port *uport) 3154 { 3155 struct uart_state *state; 3156 struct tty_port *port; 3157 int ret = 0; 3158 struct device *tty_dev; 3159 int num_groups; 3160 3161 if (uport->line >= drv->nr) 3162 return -EINVAL; 3163 3164 state = drv->state + uport->line; 3165 port = &state->port; 3166 3167 mutex_lock(&port->mutex); 3168 if (state->uart_port) { 3169 ret = -EINVAL; 3170 goto out; 3171 } 3172 3173 /* Link the port to the driver state table and vice versa */ 3174 atomic_set(&state->refcount, 1); 3175 init_waitqueue_head(&state->remove_wait); 3176 state->uart_port = uport; 3177 uport->state = state; 3178 3179 /* 3180 * If this port is in use as a console then the spinlock is already 3181 * initialised. 3182 */ 3183 if (!uart_console_registered(uport)) 3184 uart_port_spin_lock_init(uport); 3185 3186 state->pm_state = UART_PM_STATE_UNDEFINED; 3187 uart_port_set_cons(uport, drv->cons); 3188 uport->minor = drv->tty_driver->minor_start + uport->line; 3189 uport->name = kasprintf(GFP_KERNEL, "%s%d", drv->dev_name, 3190 drv->tty_driver->name_base + uport->line); 3191 if (!uport->name) { 3192 ret = -ENOMEM; 3193 goto out; 3194 } 3195 3196 if (uport->cons && uport->dev) 3197 of_console_check(uport->dev->of_node, uport->cons->name, uport->line); 3198 3199 tty_port_link_device(port, drv->tty_driver, uport->line); 3200 uart_configure_port(drv, state, uport); 3201 3202 port->console = uart_console(uport); 3203 3204 num_groups = 2; 3205 if (uport->attr_group) 3206 num_groups++; 3207 3208 uport->tty_groups = kcalloc(num_groups, sizeof(*uport->tty_groups), 3209 GFP_KERNEL); 3210 if (!uport->tty_groups) { 3211 ret = -ENOMEM; 3212 goto out; 3213 } 3214 uport->tty_groups[0] = &tty_dev_attr_group; 3215 if (uport->attr_group) 3216 uport->tty_groups[1] = uport->attr_group; 3217 3218 /* Ensure serdev drivers can call serdev_device_open() right away */ 3219 uport->flags &= ~UPF_DEAD; 3220 3221 /* 3222 * Register the port whether it's detected or not. This allows 3223 * setserial to be used to alter this port's parameters. 3224 */ 3225 tty_dev = tty_port_register_device_attr_serdev(port, drv->tty_driver, 3226 uport->line, uport->dev, &uport->port_dev->dev, port, 3227 uport->tty_groups); 3228 if (!IS_ERR(tty_dev)) { 3229 device_set_wakeup_capable(tty_dev, 1); 3230 } else { 3231 uport->flags |= UPF_DEAD; 3232 dev_err(uport->dev, "Cannot register tty device on line %d\n", 3233 uport->line); 3234 } 3235 3236 out: 3237 mutex_unlock(&port->mutex); 3238 3239 return ret; 3240 } 3241 3242 /** 3243 * serial_core_remove_one_port - detach a driver defined port structure 3244 * @drv: pointer to the uart low level driver structure for this port 3245 * @uport: uart port structure for this port 3246 * 3247 * Context: task context, might sleep 3248 * 3249 * This unhooks (and hangs up) the specified port structure from the core 3250 * driver. No further calls will be made to the low-level code for this port. 3251 * Caller must hold port_mutex. 3252 */ 3253 static void serial_core_remove_one_port(struct uart_driver *drv, 3254 struct uart_port *uport) 3255 { 3256 struct uart_state *state = drv->state + uport->line; 3257 struct tty_port *port = &state->port; 3258 struct uart_port *uart_port; 3259 struct tty_struct *tty; 3260 3261 mutex_lock(&port->mutex); 3262 uart_port = uart_port_check(state); 3263 if (uart_port != uport) 3264 dev_alert(uport->dev, "Removing wrong port: %p != %p\n", 3265 uart_port, uport); 3266 3267 if (!uart_port) { 3268 mutex_unlock(&port->mutex); 3269 return; 3270 } 3271 mutex_unlock(&port->mutex); 3272 3273 /* 3274 * Remove the devices from the tty layer 3275 */ 3276 tty_port_unregister_device(port, drv->tty_driver, uport->line); 3277 3278 tty = tty_port_tty_get(port); 3279 if (tty) { 3280 tty_vhangup(port->tty); 3281 tty_kref_put(tty); 3282 } 3283 3284 /* 3285 * If the port is used as a console, unregister it 3286 */ 3287 if (uart_console(uport)) 3288 unregister_console(uport->cons); 3289 3290 /* 3291 * Free the port IO and memory resources, if any. 3292 */ 3293 if (uport->type != PORT_UNKNOWN && uport->ops->release_port) 3294 uport->ops->release_port(uport); 3295 kfree(uport->tty_groups); 3296 kfree(uport->name); 3297 3298 /* 3299 * Indicate that there isn't a port here anymore. 3300 */ 3301 uport->type = PORT_UNKNOWN; 3302 uport->port_dev = NULL; 3303 3304 mutex_lock(&port->mutex); 3305 WARN_ON(atomic_dec_return(&state->refcount) < 0); 3306 wait_event(state->remove_wait, !atomic_read(&state->refcount)); 3307 state->uart_port = NULL; 3308 mutex_unlock(&port->mutex); 3309 } 3310 3311 /** 3312 * uart_match_port - are the two ports equivalent? 3313 * @port1: first port 3314 * @port2: second port 3315 * 3316 * This utility function can be used to determine whether two uart_port 3317 * structures describe the same port. 3318 */ 3319 bool uart_match_port(const struct uart_port *port1, 3320 const struct uart_port *port2) 3321 { 3322 if (port1->iotype != port2->iotype) 3323 return false; 3324 3325 switch (port1->iotype) { 3326 case UPIO_PORT: 3327 return port1->iobase == port2->iobase; 3328 case UPIO_HUB6: 3329 return port1->iobase == port2->iobase && 3330 port1->hub6 == port2->hub6; 3331 case UPIO_MEM: 3332 case UPIO_MEM16: 3333 case UPIO_MEM32: 3334 case UPIO_MEM32BE: 3335 case UPIO_AU: 3336 case UPIO_TSI: 3337 return port1->mapbase == port2->mapbase; 3338 } 3339 3340 return false; 3341 } 3342 EXPORT_SYMBOL(uart_match_port); 3343 3344 static struct serial_ctrl_device * 3345 serial_core_get_ctrl_dev(struct serial_port_device *port_dev) 3346 { 3347 struct device *dev = &port_dev->dev; 3348 3349 return to_serial_base_ctrl_device(dev->parent); 3350 } 3351 3352 /* 3353 * Find a registered serial core controller device if one exists. Returns 3354 * the first device matching the ctrl_id. Caller must hold port_mutex. 3355 */ 3356 static struct serial_ctrl_device *serial_core_ctrl_find(struct uart_driver *drv, 3357 struct device *phys_dev, 3358 int ctrl_id) 3359 { 3360 struct uart_state *state; 3361 int i; 3362 3363 lockdep_assert_held(&port_mutex); 3364 3365 for (i = 0; i < drv->nr; i++) { 3366 state = drv->state + i; 3367 if (!state->uart_port || !state->uart_port->port_dev) 3368 continue; 3369 3370 if (state->uart_port->dev == phys_dev && 3371 state->uart_port->ctrl_id == ctrl_id) 3372 return serial_core_get_ctrl_dev(state->uart_port->port_dev); 3373 } 3374 3375 return NULL; 3376 } 3377 3378 static struct serial_ctrl_device *serial_core_ctrl_device_add(struct uart_port *port) 3379 { 3380 return serial_base_ctrl_add(port, port->dev); 3381 } 3382 3383 static int serial_core_port_device_add(struct serial_ctrl_device *ctrl_dev, 3384 struct uart_port *port) 3385 { 3386 struct serial_port_device *port_dev; 3387 3388 port_dev = serial_base_port_add(port, ctrl_dev); 3389 if (IS_ERR(port_dev)) 3390 return PTR_ERR(port_dev); 3391 3392 port->port_dev = port_dev; 3393 3394 return 0; 3395 } 3396 3397 /* 3398 * Initialize a serial core port device, and a controller device if needed. 3399 */ 3400 int serial_core_register_port(struct uart_driver *drv, struct uart_port *port) 3401 { 3402 struct serial_ctrl_device *ctrl_dev, *new_ctrl_dev = NULL; 3403 int ret; 3404 3405 mutex_lock(&port_mutex); 3406 3407 /* 3408 * Prevent serial_port_runtime_resume() from trying to use the port 3409 * until serial_core_add_one_port() has completed 3410 */ 3411 port->flags |= UPF_DEAD; 3412 3413 /* Inititalize a serial core controller device if needed */ 3414 ctrl_dev = serial_core_ctrl_find(drv, port->dev, port->ctrl_id); 3415 if (!ctrl_dev) { 3416 new_ctrl_dev = serial_core_ctrl_device_add(port); 3417 if (IS_ERR(new_ctrl_dev)) { 3418 ret = PTR_ERR(new_ctrl_dev); 3419 goto err_unlock; 3420 } 3421 ctrl_dev = new_ctrl_dev; 3422 } 3423 3424 /* 3425 * Initialize a serial core port device. Tag the port dead to prevent 3426 * serial_port_runtime_resume() trying to do anything until port has 3427 * been registered. It gets cleared by serial_core_add_one_port(). 3428 */ 3429 ret = serial_core_port_device_add(ctrl_dev, port); 3430 if (ret) 3431 goto err_unregister_ctrl_dev; 3432 3433 ret = serial_base_match_and_update_preferred_console(drv, port); 3434 if (ret) 3435 goto err_unregister_port_dev; 3436 3437 ret = serial_core_add_one_port(drv, port); 3438 if (ret) 3439 goto err_unregister_port_dev; 3440 3441 mutex_unlock(&port_mutex); 3442 3443 return 0; 3444 3445 err_unregister_port_dev: 3446 serial_base_port_device_remove(port->port_dev); 3447 3448 err_unregister_ctrl_dev: 3449 serial_base_ctrl_device_remove(new_ctrl_dev); 3450 3451 err_unlock: 3452 mutex_unlock(&port_mutex); 3453 3454 return ret; 3455 } 3456 3457 /* 3458 * Removes a serial core port device, and the related serial core controller 3459 * device if the last instance. 3460 */ 3461 void serial_core_unregister_port(struct uart_driver *drv, struct uart_port *port) 3462 { 3463 struct device *phys_dev = port->dev; 3464 struct serial_port_device *port_dev = port->port_dev; 3465 struct serial_ctrl_device *ctrl_dev = serial_core_get_ctrl_dev(port_dev); 3466 int ctrl_id = port->ctrl_id; 3467 3468 mutex_lock(&port_mutex); 3469 3470 port->flags |= UPF_DEAD; 3471 3472 serial_core_remove_one_port(drv, port); 3473 3474 /* Note that struct uart_port *port is no longer valid at this point */ 3475 serial_base_port_device_remove(port_dev); 3476 3477 /* Drop the serial core controller device if no ports are using it */ 3478 if (!serial_core_ctrl_find(drv, phys_dev, ctrl_id)) 3479 serial_base_ctrl_device_remove(ctrl_dev); 3480 3481 mutex_unlock(&port_mutex); 3482 } 3483 3484 /** 3485 * uart_handle_dcd_change - handle a change of carrier detect state 3486 * @uport: uart_port structure for the open port 3487 * @active: new carrier detect status 3488 * 3489 * Caller must hold uport->lock. 3490 */ 3491 void uart_handle_dcd_change(struct uart_port *uport, bool active) 3492 { 3493 struct tty_port *port = &uport->state->port; 3494 struct tty_struct *tty = port->tty; 3495 struct tty_ldisc *ld; 3496 3497 lockdep_assert_held_once(&uport->lock); 3498 3499 if (tty) { 3500 ld = tty_ldisc_ref(tty); 3501 if (ld) { 3502 if (ld->ops->dcd_change) 3503 ld->ops->dcd_change(tty, active); 3504 tty_ldisc_deref(ld); 3505 } 3506 } 3507 3508 uport->icount.dcd++; 3509 3510 if (uart_dcd_enabled(uport)) { 3511 if (active) 3512 wake_up_interruptible(&port->open_wait); 3513 else if (tty) 3514 tty_hangup(tty); 3515 } 3516 } 3517 EXPORT_SYMBOL_GPL(uart_handle_dcd_change); 3518 3519 /** 3520 * uart_handle_cts_change - handle a change of clear-to-send state 3521 * @uport: uart_port structure for the open port 3522 * @active: new clear-to-send status 3523 * 3524 * Caller must hold uport->lock. 3525 */ 3526 void uart_handle_cts_change(struct uart_port *uport, bool active) 3527 { 3528 lockdep_assert_held_once(&uport->lock); 3529 3530 uport->icount.cts++; 3531 3532 if (uart_softcts_mode(uport)) { 3533 if (uport->hw_stopped) { 3534 if (active) { 3535 uport->hw_stopped = false; 3536 uport->ops->start_tx(uport); 3537 uart_write_wakeup(uport); 3538 } 3539 } else { 3540 if (!active) { 3541 uport->hw_stopped = true; 3542 uport->ops->stop_tx(uport); 3543 } 3544 } 3545 3546 } 3547 } 3548 EXPORT_SYMBOL_GPL(uart_handle_cts_change); 3549 3550 /** 3551 * uart_insert_char - push a char to the uart layer 3552 * 3553 * User is responsible to call tty_flip_buffer_push when they are done with 3554 * insertion. 3555 * 3556 * @port: corresponding port 3557 * @status: state of the serial port RX buffer (LSR for 8250) 3558 * @overrun: mask of overrun bits in @status 3559 * @ch: character to push 3560 * @flag: flag for the character (see TTY_NORMAL and friends) 3561 */ 3562 void uart_insert_char(struct uart_port *port, unsigned int status, 3563 unsigned int overrun, u8 ch, u8 flag) 3564 { 3565 struct tty_port *tport = &port->state->port; 3566 3567 if ((status & port->ignore_status_mask & ~overrun) == 0) 3568 if (tty_insert_flip_char(tport, ch, flag) == 0) 3569 ++port->icount.buf_overrun; 3570 3571 /* 3572 * Overrun is special. Since it's reported immediately, 3573 * it doesn't affect the current character. 3574 */ 3575 if (status & ~port->ignore_status_mask & overrun) 3576 if (tty_insert_flip_char(tport, 0, TTY_OVERRUN) == 0) 3577 ++port->icount.buf_overrun; 3578 } 3579 EXPORT_SYMBOL_GPL(uart_insert_char); 3580 3581 #ifdef CONFIG_MAGIC_SYSRQ_SERIAL 3582 static const u8 sysrq_toggle_seq[] = CONFIG_MAGIC_SYSRQ_SERIAL_SEQUENCE; 3583 3584 static void uart_sysrq_on(struct work_struct *w) 3585 { 3586 int sysrq_toggle_seq_len = strlen(sysrq_toggle_seq); 3587 3588 sysrq_toggle_support(1); 3589 pr_info("SysRq is enabled by magic sequence '%*pE' on serial\n", 3590 sysrq_toggle_seq_len, sysrq_toggle_seq); 3591 } 3592 static DECLARE_WORK(sysrq_enable_work, uart_sysrq_on); 3593 3594 /** 3595 * uart_try_toggle_sysrq - Enables SysRq from serial line 3596 * @port: uart_port structure where char(s) after BREAK met 3597 * @ch: new character in the sequence after received BREAK 3598 * 3599 * Enables magic SysRq when the required sequence is met on port 3600 * (see CONFIG_MAGIC_SYSRQ_SERIAL_SEQUENCE). 3601 * 3602 * Returns: %false if @ch is out of enabling sequence and should be 3603 * handled some other way, %true if @ch was consumed. 3604 */ 3605 bool uart_try_toggle_sysrq(struct uart_port *port, u8 ch) 3606 { 3607 int sysrq_toggle_seq_len = strlen(sysrq_toggle_seq); 3608 3609 if (!sysrq_toggle_seq_len) 3610 return false; 3611 3612 BUILD_BUG_ON(ARRAY_SIZE(sysrq_toggle_seq) >= U8_MAX); 3613 if (sysrq_toggle_seq[port->sysrq_seq] != ch) { 3614 port->sysrq_seq = 0; 3615 return false; 3616 } 3617 3618 if (++port->sysrq_seq < sysrq_toggle_seq_len) { 3619 port->sysrq = jiffies + SYSRQ_TIMEOUT; 3620 return true; 3621 } 3622 3623 schedule_work(&sysrq_enable_work); 3624 3625 port->sysrq = 0; 3626 return true; 3627 } 3628 EXPORT_SYMBOL_GPL(uart_try_toggle_sysrq); 3629 #endif 3630 3631 /** 3632 * uart_get_rs485_mode() - retrieve rs485 properties for given uart 3633 * @port: uart device's target port 3634 * 3635 * This function implements the device tree binding described in 3636 * Documentation/devicetree/bindings/serial/rs485.txt. 3637 */ 3638 int uart_get_rs485_mode(struct uart_port *port) 3639 { 3640 struct serial_rs485 *rs485conf = &port->rs485; 3641 struct device *dev = port->dev; 3642 enum gpiod_flags dflags; 3643 struct gpio_desc *desc; 3644 u32 rs485_delay[2]; 3645 int ret; 3646 3647 if (!(port->rs485_supported.flags & SER_RS485_ENABLED)) 3648 return 0; 3649 3650 ret = device_property_read_u32_array(dev, "rs485-rts-delay", 3651 rs485_delay, 2); 3652 if (!ret) { 3653 rs485conf->delay_rts_before_send = rs485_delay[0]; 3654 rs485conf->delay_rts_after_send = rs485_delay[1]; 3655 } else { 3656 rs485conf->delay_rts_before_send = 0; 3657 rs485conf->delay_rts_after_send = 0; 3658 } 3659 3660 uart_sanitize_serial_rs485_delays(port, rs485conf); 3661 3662 /* 3663 * Clear full-duplex and enabled flags, set RTS polarity to active high 3664 * to get to a defined state with the following properties: 3665 */ 3666 rs485conf->flags &= ~(SER_RS485_RX_DURING_TX | SER_RS485_ENABLED | 3667 SER_RS485_TERMINATE_BUS | 3668 SER_RS485_RTS_AFTER_SEND); 3669 rs485conf->flags |= SER_RS485_RTS_ON_SEND; 3670 3671 if (device_property_read_bool(dev, "rs485-rx-during-tx")) 3672 rs485conf->flags |= SER_RS485_RX_DURING_TX; 3673 3674 if (device_property_read_bool(dev, "linux,rs485-enabled-at-boot-time")) 3675 rs485conf->flags |= SER_RS485_ENABLED; 3676 3677 if (device_property_read_bool(dev, "rs485-rts-active-low")) { 3678 rs485conf->flags &= ~SER_RS485_RTS_ON_SEND; 3679 rs485conf->flags |= SER_RS485_RTS_AFTER_SEND; 3680 } 3681 3682 /* 3683 * Disabling termination by default is the safe choice: Else if many 3684 * bus participants enable it, no communication is possible at all. 3685 * Works fine for short cables and users may enable for longer cables. 3686 */ 3687 desc = devm_gpiod_get_optional(dev, "rs485-term", GPIOD_OUT_LOW); 3688 if (IS_ERR(desc)) 3689 return dev_err_probe(dev, PTR_ERR(desc), "Cannot get rs485-term-gpios\n"); 3690 port->rs485_term_gpio = desc; 3691 if (port->rs485_term_gpio) 3692 port->rs485_supported.flags |= SER_RS485_TERMINATE_BUS; 3693 3694 dflags = (rs485conf->flags & SER_RS485_RX_DURING_TX) ? 3695 GPIOD_OUT_HIGH : GPIOD_OUT_LOW; 3696 desc = devm_gpiod_get_optional(dev, "rs485-rx-during-tx", dflags); 3697 if (IS_ERR(desc)) 3698 return dev_err_probe(dev, PTR_ERR(desc), "Cannot get rs485-rx-during-tx-gpios\n"); 3699 port->rs485_rx_during_tx_gpio = desc; 3700 if (port->rs485_rx_during_tx_gpio) 3701 port->rs485_supported.flags |= SER_RS485_RX_DURING_TX; 3702 3703 return 0; 3704 } 3705 EXPORT_SYMBOL_GPL(uart_get_rs485_mode); 3706 3707 /* Compile-time assertions for serial_rs485 layout */ 3708 static_assert(offsetof(struct serial_rs485, padding) == 3709 (offsetof(struct serial_rs485, delay_rts_after_send) + sizeof(__u32))); 3710 static_assert(offsetof(struct serial_rs485, padding1) == 3711 offsetof(struct serial_rs485, padding[1])); 3712 static_assert((offsetof(struct serial_rs485, padding[4]) + sizeof(__u32)) == 3713 sizeof(struct serial_rs485)); 3714 3715 MODULE_DESCRIPTION("Serial driver core"); 3716 MODULE_LICENSE("GPL"); 3717