1 // SPDX-License-Identifier: GPL-2.0 2 // Copyright (c) 2017-2018, The Linux foundation. All rights reserved. 3 4 /* Disable MMIO tracing to prevent excessive logging of unwanted MMIO traces */ 5 #define __DISABLE_TRACE_MMIO__ 6 7 #include <linux/clk.h> 8 #include <linux/console.h> 9 #include <linux/io.h> 10 #include <linux/iopoll.h> 11 #include <linux/irq.h> 12 #include <linux/module.h> 13 #include <linux/of.h> 14 #include <linux/pm_opp.h> 15 #include <linux/platform_device.h> 16 #include <linux/pm_runtime.h> 17 #include <linux/pm_wakeirq.h> 18 #include <linux/soc/qcom/geni-se.h> 19 #include <linux/serial.h> 20 #include <linux/serial_core.h> 21 #include <linux/slab.h> 22 #include <linux/tty.h> 23 #include <linux/tty_flip.h> 24 #include <dt-bindings/interconnect/qcom,icc.h> 25 26 /* UART specific GENI registers */ 27 #define SE_UART_LOOPBACK_CFG 0x22c 28 #define SE_UART_IO_MACRO_CTRL 0x240 29 #define SE_UART_TX_TRANS_CFG 0x25c 30 #define SE_UART_TX_WORD_LEN 0x268 31 #define SE_UART_TX_STOP_BIT_LEN 0x26c 32 #define SE_UART_TX_TRANS_LEN 0x270 33 #define SE_UART_RX_TRANS_CFG 0x280 34 #define SE_UART_RX_WORD_LEN 0x28c 35 #define SE_UART_RX_STALE_CNT 0x294 36 #define SE_UART_TX_PARITY_CFG 0x2a4 37 #define SE_UART_RX_PARITY_CFG 0x2a8 38 #define SE_UART_MANUAL_RFR 0x2ac 39 40 /* SE_UART_TRANS_CFG */ 41 #define UART_TX_PAR_EN BIT(0) 42 #define UART_CTS_MASK BIT(1) 43 44 /* SE_UART_TX_STOP_BIT_LEN */ 45 #define TX_STOP_BIT_LEN_1 0 46 #define TX_STOP_BIT_LEN_2 2 47 48 /* SE_UART_RX_TRANS_CFG */ 49 #define UART_RX_PAR_EN BIT(3) 50 51 /* SE_UART_RX_WORD_LEN */ 52 #define RX_WORD_LEN_MASK GENMASK(9, 0) 53 54 /* SE_UART_RX_STALE_CNT */ 55 #define RX_STALE_CNT GENMASK(23, 0) 56 57 /* SE_UART_TX_PARITY_CFG/RX_PARITY_CFG */ 58 #define PAR_CALC_EN BIT(0) 59 #define PAR_EVEN 0x00 60 #define PAR_ODD 0x01 61 #define PAR_SPACE 0x10 62 63 /* SE_UART_MANUAL_RFR register fields */ 64 #define UART_MANUAL_RFR_EN BIT(31) 65 #define UART_RFR_NOT_READY BIT(1) 66 #define UART_RFR_READY BIT(0) 67 68 /* UART M_CMD OP codes */ 69 #define UART_START_TX 0x1 70 /* UART S_CMD OP codes */ 71 #define UART_START_READ 0x1 72 #define UART_PARAM 0x1 73 #define UART_PARAM_RFR_OPEN BIT(7) 74 75 #define UART_OVERSAMPLING 32 76 #define STALE_TIMEOUT 16 77 #define DEFAULT_BITS_PER_CHAR 10 78 #define GENI_UART_CONS_PORTS 1 79 #define GENI_UART_PORTS 3 80 #define DEF_FIFO_DEPTH_WORDS 16 81 #define DEF_TX_WM 2 82 #define DEF_FIFO_WIDTH_BITS 32 83 #define UART_RX_WM 2 84 85 /* SE_UART_LOOPBACK_CFG */ 86 #define RX_TX_SORTED BIT(0) 87 #define CTS_RTS_SORTED BIT(1) 88 #define RX_TX_CTS_RTS_SORTED (RX_TX_SORTED | CTS_RTS_SORTED) 89 90 /* UART pin swap value */ 91 #define DEFAULT_IO_MACRO_IO0_IO1_MASK GENMASK(3, 0) 92 #define IO_MACRO_IO0_SEL 0x3 93 #define DEFAULT_IO_MACRO_IO2_IO3_MASK GENMASK(15, 4) 94 #define IO_MACRO_IO2_IO3_SWAP 0x4640 95 96 /* We always configure 4 bytes per FIFO word */ 97 #define BYTES_PER_FIFO_WORD 4U 98 99 #define DMA_RX_BUF_SIZE 2048 100 101 struct qcom_geni_device_data { 102 bool console; 103 enum geni_se_xfer_mode mode; 104 }; 105 106 struct qcom_geni_private_data { 107 /* NOTE: earlycon port will have NULL here */ 108 struct uart_driver *drv; 109 110 u32 poll_cached_bytes; 111 unsigned int poll_cached_bytes_cnt; 112 113 u32 write_cached_bytes; 114 unsigned int write_cached_bytes_cnt; 115 }; 116 117 struct qcom_geni_serial_port { 118 struct uart_port uport; 119 struct geni_se se; 120 const char *name; 121 u32 tx_fifo_depth; 122 u32 tx_fifo_width; 123 u32 rx_fifo_depth; 124 dma_addr_t tx_dma_addr; 125 dma_addr_t rx_dma_addr; 126 bool setup; 127 unsigned int baud; 128 unsigned long clk_rate; 129 void *rx_buf; 130 u32 loopback; 131 bool brk; 132 133 unsigned int tx_remaining; 134 int wakeup_irq; 135 bool rx_tx_swap; 136 bool cts_rts_swap; 137 138 struct qcom_geni_private_data private_data; 139 const struct qcom_geni_device_data *dev_data; 140 }; 141 142 static const struct uart_ops qcom_geni_console_pops; 143 static const struct uart_ops qcom_geni_uart_pops; 144 static struct uart_driver qcom_geni_console_driver; 145 static struct uart_driver qcom_geni_uart_driver; 146 147 static inline struct qcom_geni_serial_port *to_dev_port(struct uart_port *uport) 148 { 149 return container_of(uport, struct qcom_geni_serial_port, uport); 150 } 151 152 static struct qcom_geni_serial_port qcom_geni_uart_ports[GENI_UART_PORTS] = { 153 [0] = { 154 .uport = { 155 .iotype = UPIO_MEM, 156 .ops = &qcom_geni_uart_pops, 157 .flags = UPF_BOOT_AUTOCONF, 158 .line = 0, 159 }, 160 }, 161 [1] = { 162 .uport = { 163 .iotype = UPIO_MEM, 164 .ops = &qcom_geni_uart_pops, 165 .flags = UPF_BOOT_AUTOCONF, 166 .line = 1, 167 }, 168 }, 169 [2] = { 170 .uport = { 171 .iotype = UPIO_MEM, 172 .ops = &qcom_geni_uart_pops, 173 .flags = UPF_BOOT_AUTOCONF, 174 .line = 2, 175 }, 176 }, 177 }; 178 179 static struct qcom_geni_serial_port qcom_geni_console_port = { 180 .uport = { 181 .iotype = UPIO_MEM, 182 .ops = &qcom_geni_console_pops, 183 .flags = UPF_BOOT_AUTOCONF, 184 .line = 0, 185 }, 186 }; 187 188 static int qcom_geni_serial_request_port(struct uart_port *uport) 189 { 190 struct platform_device *pdev = to_platform_device(uport->dev); 191 struct qcom_geni_serial_port *port = to_dev_port(uport); 192 193 uport->membase = devm_platform_ioremap_resource(pdev, 0); 194 if (IS_ERR(uport->membase)) 195 return PTR_ERR(uport->membase); 196 port->se.base = uport->membase; 197 return 0; 198 } 199 200 static void qcom_geni_serial_config_port(struct uart_port *uport, int cfg_flags) 201 { 202 if (cfg_flags & UART_CONFIG_TYPE) { 203 uport->type = PORT_MSM; 204 qcom_geni_serial_request_port(uport); 205 } 206 } 207 208 static unsigned int qcom_geni_serial_get_mctrl(struct uart_port *uport) 209 { 210 unsigned int mctrl = TIOCM_DSR | TIOCM_CAR; 211 u32 geni_ios; 212 213 if (uart_console(uport)) { 214 mctrl |= TIOCM_CTS; 215 } else { 216 geni_ios = readl(uport->membase + SE_GENI_IOS); 217 if (!(geni_ios & IO2_DATA_IN)) 218 mctrl |= TIOCM_CTS; 219 } 220 221 return mctrl; 222 } 223 224 static void qcom_geni_serial_set_mctrl(struct uart_port *uport, 225 unsigned int mctrl) 226 { 227 u32 uart_manual_rfr = 0; 228 struct qcom_geni_serial_port *port = to_dev_port(uport); 229 230 if (uart_console(uport)) 231 return; 232 233 if (mctrl & TIOCM_LOOP) 234 port->loopback = RX_TX_CTS_RTS_SORTED; 235 236 if (!(mctrl & TIOCM_RTS) && !uport->suspended) 237 uart_manual_rfr = UART_MANUAL_RFR_EN | UART_RFR_NOT_READY; 238 writel(uart_manual_rfr, uport->membase + SE_UART_MANUAL_RFR); 239 } 240 241 static const char *qcom_geni_serial_get_type(struct uart_port *uport) 242 { 243 return "MSM"; 244 } 245 246 static struct qcom_geni_serial_port *get_port_from_line(int line, bool console) 247 { 248 struct qcom_geni_serial_port *port; 249 int nr_ports = console ? GENI_UART_CONS_PORTS : GENI_UART_PORTS; 250 251 if (line < 0 || line >= nr_ports) 252 return ERR_PTR(-ENXIO); 253 254 port = console ? &qcom_geni_console_port : &qcom_geni_uart_ports[line]; 255 return port; 256 } 257 258 static bool qcom_geni_serial_main_active(struct uart_port *uport) 259 { 260 return readl(uport->membase + SE_GENI_STATUS) & M_GENI_CMD_ACTIVE; 261 } 262 263 static bool qcom_geni_serial_secondary_active(struct uart_port *uport) 264 { 265 return readl(uport->membase + SE_GENI_STATUS) & S_GENI_CMD_ACTIVE; 266 } 267 268 static bool qcom_geni_serial_poll_bit(struct uart_port *uport, 269 int offset, int field, bool set) 270 { 271 u32 reg; 272 struct qcom_geni_serial_port *port; 273 unsigned int baud; 274 unsigned int fifo_bits; 275 unsigned long timeout_us = 20000; 276 struct qcom_geni_private_data *private_data = uport->private_data; 277 278 if (private_data->drv) { 279 port = to_dev_port(uport); 280 baud = port->baud; 281 if (!baud) 282 baud = 115200; 283 fifo_bits = port->tx_fifo_depth * port->tx_fifo_width; 284 /* 285 * Total polling iterations based on FIFO worth of bytes to be 286 * sent at current baud. Add a little fluff to the wait. 287 */ 288 timeout_us = ((fifo_bits * USEC_PER_SEC) / baud) + 500; 289 } 290 291 /* 292 * Use custom implementation instead of readl_poll_atomic since ktimer 293 * is not ready at the time of early console. 294 */ 295 timeout_us = DIV_ROUND_UP(timeout_us, 10) * 10; 296 while (timeout_us) { 297 reg = readl(uport->membase + offset); 298 if ((bool)(reg & field) == set) 299 return true; 300 udelay(10); 301 timeout_us -= 10; 302 } 303 return false; 304 } 305 306 static void qcom_geni_serial_setup_tx(struct uart_port *uport, u32 xmit_size) 307 { 308 u32 m_cmd; 309 310 writel(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN); 311 m_cmd = UART_START_TX << M_OPCODE_SHFT; 312 writel(m_cmd, uport->membase + SE_GENI_M_CMD0); 313 } 314 315 static void qcom_geni_serial_poll_tx_done(struct uart_port *uport) 316 { 317 int done; 318 u32 irq_clear = M_CMD_DONE_EN; 319 320 done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 321 M_CMD_DONE_EN, true); 322 if (!done) { 323 writel(M_GENI_CMD_ABORT, uport->membase + 324 SE_GENI_M_CMD_CTRL_REG); 325 irq_clear |= M_CMD_ABORT_EN; 326 qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 327 M_CMD_ABORT_EN, true); 328 } 329 writel(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR); 330 } 331 332 static void qcom_geni_serial_abort_rx(struct uart_port *uport) 333 { 334 u32 irq_clear = S_CMD_DONE_EN | S_CMD_ABORT_EN; 335 336 writel(S_GENI_CMD_ABORT, uport->membase + SE_GENI_S_CMD_CTRL_REG); 337 qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG, 338 S_GENI_CMD_ABORT, false); 339 writel(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR); 340 writel(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG); 341 } 342 343 #ifdef CONFIG_CONSOLE_POLL 344 static int qcom_geni_serial_get_char(struct uart_port *uport) 345 { 346 struct qcom_geni_private_data *private_data = uport->private_data; 347 u32 status; 348 u32 word_cnt; 349 int ret; 350 351 if (!private_data->poll_cached_bytes_cnt) { 352 status = readl(uport->membase + SE_GENI_M_IRQ_STATUS); 353 writel(status, uport->membase + SE_GENI_M_IRQ_CLEAR); 354 355 status = readl(uport->membase + SE_GENI_S_IRQ_STATUS); 356 writel(status, uport->membase + SE_GENI_S_IRQ_CLEAR); 357 358 status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS); 359 word_cnt = status & RX_FIFO_WC_MSK; 360 if (!word_cnt) 361 return NO_POLL_CHAR; 362 363 if (word_cnt == 1 && (status & RX_LAST)) 364 /* 365 * NOTE: If RX_LAST_BYTE_VALID is 0 it needs to be 366 * treated as if it was BYTES_PER_FIFO_WORD. 367 */ 368 private_data->poll_cached_bytes_cnt = 369 (status & RX_LAST_BYTE_VALID_MSK) >> 370 RX_LAST_BYTE_VALID_SHFT; 371 372 if (private_data->poll_cached_bytes_cnt == 0) 373 private_data->poll_cached_bytes_cnt = BYTES_PER_FIFO_WORD; 374 375 private_data->poll_cached_bytes = 376 readl(uport->membase + SE_GENI_RX_FIFOn); 377 } 378 379 private_data->poll_cached_bytes_cnt--; 380 ret = private_data->poll_cached_bytes & 0xff; 381 private_data->poll_cached_bytes >>= 8; 382 383 return ret; 384 } 385 386 static void qcom_geni_serial_poll_put_char(struct uart_port *uport, 387 unsigned char c) 388 { 389 writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); 390 qcom_geni_serial_setup_tx(uport, 1); 391 WARN_ON(!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 392 M_TX_FIFO_WATERMARK_EN, true)); 393 writel(c, uport->membase + SE_GENI_TX_FIFOn); 394 writel(M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); 395 qcom_geni_serial_poll_tx_done(uport); 396 } 397 #endif 398 399 #ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE 400 static void qcom_geni_serial_wr_char(struct uart_port *uport, unsigned char ch) 401 { 402 struct qcom_geni_private_data *private_data = uport->private_data; 403 404 private_data->write_cached_bytes = 405 (private_data->write_cached_bytes >> 8) | (ch << 24); 406 private_data->write_cached_bytes_cnt++; 407 408 if (private_data->write_cached_bytes_cnt == BYTES_PER_FIFO_WORD) { 409 writel(private_data->write_cached_bytes, 410 uport->membase + SE_GENI_TX_FIFOn); 411 private_data->write_cached_bytes_cnt = 0; 412 } 413 } 414 415 static void 416 __qcom_geni_serial_console_write(struct uart_port *uport, const char *s, 417 unsigned int count) 418 { 419 struct qcom_geni_private_data *private_data = uport->private_data; 420 421 int i; 422 u32 bytes_to_send = count; 423 424 for (i = 0; i < count; i++) { 425 /* 426 * uart_console_write() adds a carriage return for each newline. 427 * Account for additional bytes to be written. 428 */ 429 if (s[i] == '\n') 430 bytes_to_send++; 431 } 432 433 writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); 434 qcom_geni_serial_setup_tx(uport, bytes_to_send); 435 for (i = 0; i < count; ) { 436 size_t chars_to_write = 0; 437 size_t avail = DEF_FIFO_DEPTH_WORDS - DEF_TX_WM; 438 439 /* 440 * If the WM bit never set, then the Tx state machine is not 441 * in a valid state, so break, cancel/abort any existing 442 * command. Unfortunately the current data being written is 443 * lost. 444 */ 445 if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 446 M_TX_FIFO_WATERMARK_EN, true)) 447 break; 448 chars_to_write = min_t(size_t, count - i, avail / 2); 449 uart_console_write(uport, s + i, chars_to_write, 450 qcom_geni_serial_wr_char); 451 writel(M_TX_FIFO_WATERMARK_EN, uport->membase + 452 SE_GENI_M_IRQ_CLEAR); 453 i += chars_to_write; 454 } 455 456 if (private_data->write_cached_bytes_cnt) { 457 private_data->write_cached_bytes >>= BITS_PER_BYTE * 458 (BYTES_PER_FIFO_WORD - private_data->write_cached_bytes_cnt); 459 writel(private_data->write_cached_bytes, 460 uport->membase + SE_GENI_TX_FIFOn); 461 private_data->write_cached_bytes_cnt = 0; 462 } 463 464 qcom_geni_serial_poll_tx_done(uport); 465 } 466 467 static void qcom_geni_serial_console_write(struct console *co, const char *s, 468 unsigned int count) 469 { 470 struct uart_port *uport; 471 struct qcom_geni_serial_port *port; 472 bool locked = true; 473 unsigned long flags; 474 u32 geni_status; 475 u32 irq_en; 476 477 WARN_ON(co->index < 0 || co->index >= GENI_UART_CONS_PORTS); 478 479 port = get_port_from_line(co->index, true); 480 if (IS_ERR(port)) 481 return; 482 483 uport = &port->uport; 484 if (oops_in_progress) 485 locked = spin_trylock_irqsave(&uport->lock, flags); 486 else 487 spin_lock_irqsave(&uport->lock, flags); 488 489 geni_status = readl(uport->membase + SE_GENI_STATUS); 490 491 /* Cancel the current write to log the fault */ 492 if (!locked) { 493 geni_se_cancel_m_cmd(&port->se); 494 if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 495 M_CMD_CANCEL_EN, true)) { 496 geni_se_abort_m_cmd(&port->se); 497 qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 498 M_CMD_ABORT_EN, true); 499 writel(M_CMD_ABORT_EN, uport->membase + 500 SE_GENI_M_IRQ_CLEAR); 501 } 502 writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); 503 } else if ((geni_status & M_GENI_CMD_ACTIVE) && !port->tx_remaining) { 504 /* 505 * It seems we can't interrupt existing transfers if all data 506 * has been sent, in which case we need to look for done first. 507 */ 508 qcom_geni_serial_poll_tx_done(uport); 509 510 if (!uart_circ_empty(&uport->state->xmit)) { 511 irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 512 writel(irq_en | M_TX_FIFO_WATERMARK_EN, 513 uport->membase + SE_GENI_M_IRQ_EN); 514 } 515 } 516 517 __qcom_geni_serial_console_write(uport, s, count); 518 519 if (port->tx_remaining) 520 qcom_geni_serial_setup_tx(uport, port->tx_remaining); 521 522 if (locked) 523 spin_unlock_irqrestore(&uport->lock, flags); 524 } 525 526 static void handle_rx_console(struct uart_port *uport, u32 bytes, bool drop) 527 { 528 u32 i; 529 unsigned char buf[sizeof(u32)]; 530 struct tty_port *tport; 531 struct qcom_geni_serial_port *port = to_dev_port(uport); 532 533 tport = &uport->state->port; 534 for (i = 0; i < bytes; ) { 535 int c; 536 int chunk = min_t(int, bytes - i, BYTES_PER_FIFO_WORD); 537 538 ioread32_rep(uport->membase + SE_GENI_RX_FIFOn, buf, 1); 539 i += chunk; 540 if (drop) 541 continue; 542 543 for (c = 0; c < chunk; c++) { 544 int sysrq; 545 546 uport->icount.rx++; 547 if (port->brk && buf[c] == 0) { 548 port->brk = false; 549 if (uart_handle_break(uport)) 550 continue; 551 } 552 553 sysrq = uart_prepare_sysrq_char(uport, buf[c]); 554 555 if (!sysrq) 556 tty_insert_flip_char(tport, buf[c], TTY_NORMAL); 557 } 558 } 559 if (!drop) 560 tty_flip_buffer_push(tport); 561 } 562 #else 563 static void handle_rx_console(struct uart_port *uport, u32 bytes, bool drop) 564 { 565 566 } 567 #endif /* CONFIG_SERIAL_QCOM_GENI_CONSOLE */ 568 569 static void handle_rx_uart(struct uart_port *uport, u32 bytes, bool drop) 570 { 571 struct qcom_geni_serial_port *port = to_dev_port(uport); 572 struct tty_port *tport = &uport->state->port; 573 int ret; 574 575 ret = tty_insert_flip_string(tport, port->rx_buf, bytes); 576 if (ret != bytes) { 577 dev_err(uport->dev, "%s:Unable to push data ret %d_bytes %d\n", 578 __func__, ret, bytes); 579 WARN_ON_ONCE(1); 580 } 581 uport->icount.rx += ret; 582 tty_flip_buffer_push(tport); 583 } 584 585 static unsigned int qcom_geni_serial_tx_empty(struct uart_port *uport) 586 { 587 return !readl(uport->membase + SE_GENI_TX_FIFO_STATUS); 588 } 589 590 static void qcom_geni_serial_stop_tx_dma(struct uart_port *uport) 591 { 592 struct qcom_geni_serial_port *port = to_dev_port(uport); 593 bool done; 594 595 if (!qcom_geni_serial_main_active(uport)) 596 return; 597 598 if (port->tx_dma_addr) { 599 geni_se_tx_dma_unprep(&port->se, port->tx_dma_addr, 600 port->tx_remaining); 601 port->tx_dma_addr = 0; 602 port->tx_remaining = 0; 603 } 604 605 geni_se_cancel_m_cmd(&port->se); 606 607 done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 608 M_CMD_CANCEL_EN, true); 609 if (!done) { 610 geni_se_abort_m_cmd(&port->se); 611 done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 612 M_CMD_ABORT_EN, true); 613 if (!done) 614 dev_err_ratelimited(uport->dev, "M_CMD_ABORT_EN not set"); 615 writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); 616 } 617 618 writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); 619 } 620 621 static void qcom_geni_serial_start_tx_dma(struct uart_port *uport) 622 { 623 struct qcom_geni_serial_port *port = to_dev_port(uport); 624 struct circ_buf *xmit = &uport->state->xmit; 625 unsigned int xmit_size; 626 int ret; 627 628 if (port->tx_dma_addr) 629 return; 630 631 if (uart_circ_empty(xmit)) 632 return; 633 634 xmit_size = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); 635 636 qcom_geni_serial_setup_tx(uport, xmit_size); 637 638 ret = geni_se_tx_dma_prep(&port->se, &xmit->buf[xmit->tail], 639 xmit_size, &port->tx_dma_addr); 640 if (ret) { 641 dev_err(uport->dev, "unable to start TX SE DMA: %d\n", ret); 642 qcom_geni_serial_stop_tx_dma(uport); 643 return; 644 } 645 646 port->tx_remaining = xmit_size; 647 } 648 649 static void qcom_geni_serial_start_tx_fifo(struct uart_port *uport) 650 { 651 u32 irq_en; 652 653 if (qcom_geni_serial_main_active(uport) || 654 !qcom_geni_serial_tx_empty(uport)) 655 return; 656 657 irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 658 irq_en |= M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN; 659 660 writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG); 661 writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); 662 } 663 664 static void qcom_geni_serial_stop_tx_fifo(struct uart_port *uport) 665 { 666 u32 irq_en; 667 struct qcom_geni_serial_port *port = to_dev_port(uport); 668 669 irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 670 irq_en &= ~(M_CMD_DONE_EN | M_TX_FIFO_WATERMARK_EN); 671 writel(0, uport->membase + SE_GENI_TX_WATERMARK_REG); 672 writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); 673 /* Possible stop tx is called multiple times. */ 674 if (!qcom_geni_serial_main_active(uport)) 675 return; 676 677 geni_se_cancel_m_cmd(&port->se); 678 if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 679 M_CMD_CANCEL_EN, true)) { 680 geni_se_abort_m_cmd(&port->se); 681 qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS, 682 M_CMD_ABORT_EN, true); 683 writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); 684 } 685 writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR); 686 } 687 688 static void qcom_geni_serial_handle_rx_fifo(struct uart_port *uport, bool drop) 689 { 690 u32 status; 691 u32 word_cnt; 692 u32 last_word_byte_cnt; 693 u32 last_word_partial; 694 u32 total_bytes; 695 696 status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS); 697 word_cnt = status & RX_FIFO_WC_MSK; 698 last_word_partial = status & RX_LAST; 699 last_word_byte_cnt = (status & RX_LAST_BYTE_VALID_MSK) >> 700 RX_LAST_BYTE_VALID_SHFT; 701 702 if (!word_cnt) 703 return; 704 total_bytes = BYTES_PER_FIFO_WORD * (word_cnt - 1); 705 if (last_word_partial && last_word_byte_cnt) 706 total_bytes += last_word_byte_cnt; 707 else 708 total_bytes += BYTES_PER_FIFO_WORD; 709 handle_rx_console(uport, total_bytes, drop); 710 } 711 712 static void qcom_geni_serial_stop_rx_fifo(struct uart_port *uport) 713 { 714 u32 irq_en; 715 struct qcom_geni_serial_port *port = to_dev_port(uport); 716 u32 s_irq_status; 717 718 irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN); 719 irq_en &= ~(S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN); 720 writel(irq_en, uport->membase + SE_GENI_S_IRQ_EN); 721 722 irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 723 irq_en &= ~(M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN); 724 writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); 725 726 if (!qcom_geni_serial_secondary_active(uport)) 727 return; 728 729 geni_se_cancel_s_cmd(&port->se); 730 qcom_geni_serial_poll_bit(uport, SE_GENI_S_IRQ_STATUS, 731 S_CMD_CANCEL_EN, true); 732 /* 733 * If timeout occurs secondary engine remains active 734 * and Abort sequence is executed. 735 */ 736 s_irq_status = readl(uport->membase + SE_GENI_S_IRQ_STATUS); 737 /* Flush the Rx buffer */ 738 if (s_irq_status & S_RX_FIFO_LAST_EN) 739 qcom_geni_serial_handle_rx_fifo(uport, true); 740 writel(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR); 741 742 if (qcom_geni_serial_secondary_active(uport)) 743 qcom_geni_serial_abort_rx(uport); 744 } 745 746 static void qcom_geni_serial_start_rx_fifo(struct uart_port *uport) 747 { 748 u32 irq_en; 749 struct qcom_geni_serial_port *port = to_dev_port(uport); 750 751 if (qcom_geni_serial_secondary_active(uport)) 752 qcom_geni_serial_stop_rx_fifo(uport); 753 754 geni_se_setup_s_cmd(&port->se, UART_START_READ, 0); 755 756 irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN); 757 irq_en |= S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN; 758 writel(irq_en, uport->membase + SE_GENI_S_IRQ_EN); 759 760 irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 761 irq_en |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN; 762 writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN); 763 } 764 765 static void qcom_geni_serial_stop_rx_dma(struct uart_port *uport) 766 { 767 struct qcom_geni_serial_port *port = to_dev_port(uport); 768 769 if (!qcom_geni_serial_secondary_active(uport)) 770 return; 771 772 geni_se_cancel_s_cmd(&port->se); 773 qcom_geni_serial_poll_bit(uport, SE_GENI_S_IRQ_STATUS, 774 S_CMD_CANCEL_EN, true); 775 776 if (qcom_geni_serial_secondary_active(uport)) 777 qcom_geni_serial_abort_rx(uport); 778 779 if (port->rx_dma_addr) { 780 geni_se_rx_dma_unprep(&port->se, port->rx_dma_addr, 781 DMA_RX_BUF_SIZE); 782 port->rx_dma_addr = 0; 783 } 784 } 785 786 static void qcom_geni_serial_start_rx_dma(struct uart_port *uport) 787 { 788 struct qcom_geni_serial_port *port = to_dev_port(uport); 789 int ret; 790 791 if (qcom_geni_serial_secondary_active(uport)) 792 qcom_geni_serial_stop_rx_dma(uport); 793 794 geni_se_setup_s_cmd(&port->se, UART_START_READ, UART_PARAM_RFR_OPEN); 795 796 ret = geni_se_rx_dma_prep(&port->se, port->rx_buf, 797 DMA_RX_BUF_SIZE, 798 &port->rx_dma_addr); 799 if (ret) { 800 dev_err(uport->dev, "unable to start RX SE DMA: %d\n", ret); 801 qcom_geni_serial_stop_rx_dma(uport); 802 } 803 } 804 805 static void qcom_geni_serial_handle_rx_dma(struct uart_port *uport, bool drop) 806 { 807 struct qcom_geni_serial_port *port = to_dev_port(uport); 808 u32 rx_in; 809 int ret; 810 811 if (!qcom_geni_serial_secondary_active(uport)) 812 return; 813 814 if (!port->rx_dma_addr) 815 return; 816 817 geni_se_rx_dma_unprep(&port->se, port->rx_dma_addr, DMA_RX_BUF_SIZE); 818 port->rx_dma_addr = 0; 819 820 rx_in = readl(uport->membase + SE_DMA_RX_LEN_IN); 821 if (!rx_in) { 822 dev_warn(uport->dev, "serial engine reports 0 RX bytes in!\n"); 823 return; 824 } 825 826 if (!drop) 827 handle_rx_uart(uport, rx_in, drop); 828 829 ret = geni_se_rx_dma_prep(&port->se, port->rx_buf, 830 DMA_RX_BUF_SIZE, 831 &port->rx_dma_addr); 832 if (ret) { 833 dev_err(uport->dev, "unable to start RX SE DMA: %d\n", ret); 834 qcom_geni_serial_stop_rx_dma(uport); 835 } 836 } 837 838 static void qcom_geni_serial_start_rx(struct uart_port *uport) 839 { 840 uport->ops->start_rx(uport); 841 } 842 843 static void qcom_geni_serial_stop_rx(struct uart_port *uport) 844 { 845 uport->ops->stop_rx(uport); 846 } 847 848 static void qcom_geni_serial_stop_tx(struct uart_port *uport) 849 { 850 uport->ops->stop_tx(uport); 851 } 852 853 static void qcom_geni_serial_send_chunk_fifo(struct uart_port *uport, 854 unsigned int remaining) 855 { 856 struct qcom_geni_serial_port *port = to_dev_port(uport); 857 struct circ_buf *xmit = &uport->state->xmit; 858 unsigned int tx_bytes; 859 u8 buf[BYTES_PER_FIFO_WORD]; 860 861 while (remaining) { 862 memset(buf, 0, sizeof(buf)); 863 tx_bytes = min(remaining, BYTES_PER_FIFO_WORD); 864 865 memcpy(buf, &xmit->buf[xmit->tail], tx_bytes); 866 uart_xmit_advance(uport, tx_bytes); 867 868 iowrite32_rep(uport->membase + SE_GENI_TX_FIFOn, buf, 1); 869 870 remaining -= tx_bytes; 871 port->tx_remaining -= tx_bytes; 872 } 873 } 874 875 static void qcom_geni_serial_handle_tx_fifo(struct uart_port *uport, 876 bool done, bool active) 877 { 878 struct qcom_geni_serial_port *port = to_dev_port(uport); 879 struct circ_buf *xmit = &uport->state->xmit; 880 size_t avail; 881 size_t pending; 882 u32 status; 883 u32 irq_en; 884 unsigned int chunk; 885 886 status = readl(uport->membase + SE_GENI_TX_FIFO_STATUS); 887 888 /* Complete the current tx command before taking newly added data */ 889 if (active) 890 pending = port->tx_remaining; 891 else 892 pending = uart_circ_chars_pending(xmit); 893 894 /* All data has been transmitted and acknowledged as received */ 895 if (!pending && !status && done) { 896 qcom_geni_serial_stop_tx_fifo(uport); 897 goto out_write_wakeup; 898 } 899 900 avail = port->tx_fifo_depth - (status & TX_FIFO_WC); 901 avail *= BYTES_PER_FIFO_WORD; 902 903 chunk = min(avail, pending); 904 if (!chunk) 905 goto out_write_wakeup; 906 907 if (!port->tx_remaining) { 908 qcom_geni_serial_setup_tx(uport, pending); 909 port->tx_remaining = pending; 910 911 irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 912 if (!(irq_en & M_TX_FIFO_WATERMARK_EN)) 913 writel(irq_en | M_TX_FIFO_WATERMARK_EN, 914 uport->membase + SE_GENI_M_IRQ_EN); 915 } 916 917 qcom_geni_serial_send_chunk_fifo(uport, chunk); 918 919 /* 920 * The tx fifo watermark is level triggered and latched. Though we had 921 * cleared it in qcom_geni_serial_isr it will have already reasserted 922 * so we must clear it again here after our writes. 923 */ 924 writel(M_TX_FIFO_WATERMARK_EN, 925 uport->membase + SE_GENI_M_IRQ_CLEAR); 926 927 out_write_wakeup: 928 if (!port->tx_remaining) { 929 irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 930 if (irq_en & M_TX_FIFO_WATERMARK_EN) 931 writel(irq_en & ~M_TX_FIFO_WATERMARK_EN, 932 uport->membase + SE_GENI_M_IRQ_EN); 933 } 934 935 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 936 uart_write_wakeup(uport); 937 } 938 939 static void qcom_geni_serial_handle_tx_dma(struct uart_port *uport) 940 { 941 struct qcom_geni_serial_port *port = to_dev_port(uport); 942 struct circ_buf *xmit = &uport->state->xmit; 943 944 uart_xmit_advance(uport, port->tx_remaining); 945 geni_se_tx_dma_unprep(&port->se, port->tx_dma_addr, port->tx_remaining); 946 port->tx_dma_addr = 0; 947 port->tx_remaining = 0; 948 949 if (!uart_circ_empty(xmit)) 950 qcom_geni_serial_start_tx_dma(uport); 951 952 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 953 uart_write_wakeup(uport); 954 } 955 956 static irqreturn_t qcom_geni_serial_isr(int isr, void *dev) 957 { 958 u32 m_irq_en; 959 u32 m_irq_status; 960 u32 s_irq_status; 961 u32 geni_status; 962 u32 dma; 963 u32 dma_tx_status; 964 u32 dma_rx_status; 965 struct uart_port *uport = dev; 966 bool drop_rx = false; 967 struct tty_port *tport = &uport->state->port; 968 struct qcom_geni_serial_port *port = to_dev_port(uport); 969 970 if (uport->suspended) 971 return IRQ_NONE; 972 973 spin_lock(&uport->lock); 974 975 m_irq_status = readl(uport->membase + SE_GENI_M_IRQ_STATUS); 976 s_irq_status = readl(uport->membase + SE_GENI_S_IRQ_STATUS); 977 dma_tx_status = readl(uport->membase + SE_DMA_TX_IRQ_STAT); 978 dma_rx_status = readl(uport->membase + SE_DMA_RX_IRQ_STAT); 979 geni_status = readl(uport->membase + SE_GENI_STATUS); 980 dma = readl(uport->membase + SE_GENI_DMA_MODE_EN); 981 m_irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN); 982 writel(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR); 983 writel(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR); 984 writel(dma_tx_status, uport->membase + SE_DMA_TX_IRQ_CLR); 985 writel(dma_rx_status, uport->membase + SE_DMA_RX_IRQ_CLR); 986 987 if (WARN_ON(m_irq_status & M_ILLEGAL_CMD_EN)) 988 goto out_unlock; 989 990 if (s_irq_status & S_RX_FIFO_WR_ERR_EN) { 991 uport->icount.overrun++; 992 tty_insert_flip_char(tport, 0, TTY_OVERRUN); 993 } 994 995 if (s_irq_status & (S_GP_IRQ_0_EN | S_GP_IRQ_1_EN)) { 996 if (s_irq_status & S_GP_IRQ_0_EN) 997 uport->icount.parity++; 998 drop_rx = true; 999 } else if (s_irq_status & (S_GP_IRQ_2_EN | S_GP_IRQ_3_EN)) { 1000 uport->icount.brk++; 1001 port->brk = true; 1002 } 1003 1004 if (dma) { 1005 if (dma_tx_status & TX_DMA_DONE) 1006 qcom_geni_serial_handle_tx_dma(uport); 1007 1008 if (dma_rx_status) { 1009 if (dma_rx_status & RX_RESET_DONE) 1010 goto out_unlock; 1011 1012 if (dma_rx_status & RX_DMA_PARITY_ERR) { 1013 uport->icount.parity++; 1014 drop_rx = true; 1015 } 1016 1017 if (dma_rx_status & RX_DMA_BREAK) 1018 uport->icount.brk++; 1019 1020 if (dma_rx_status & (RX_DMA_DONE | RX_EOT)) 1021 qcom_geni_serial_handle_rx_dma(uport, drop_rx); 1022 } 1023 } else { 1024 if (m_irq_status & m_irq_en & 1025 (M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN)) 1026 qcom_geni_serial_handle_tx_fifo(uport, 1027 m_irq_status & M_CMD_DONE_EN, 1028 geni_status & M_GENI_CMD_ACTIVE); 1029 1030 if (s_irq_status & (S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN)) 1031 qcom_geni_serial_handle_rx_fifo(uport, drop_rx); 1032 } 1033 1034 out_unlock: 1035 uart_unlock_and_check_sysrq(uport); 1036 1037 return IRQ_HANDLED; 1038 } 1039 1040 static int setup_fifos(struct qcom_geni_serial_port *port) 1041 { 1042 struct uart_port *uport; 1043 u32 old_rx_fifo_depth = port->rx_fifo_depth; 1044 1045 uport = &port->uport; 1046 port->tx_fifo_depth = geni_se_get_tx_fifo_depth(&port->se); 1047 port->tx_fifo_width = geni_se_get_tx_fifo_width(&port->se); 1048 port->rx_fifo_depth = geni_se_get_rx_fifo_depth(&port->se); 1049 uport->fifosize = 1050 (port->tx_fifo_depth * port->tx_fifo_width) / BITS_PER_BYTE; 1051 1052 if (port->rx_buf && (old_rx_fifo_depth != port->rx_fifo_depth) && port->rx_fifo_depth) { 1053 /* 1054 * Use krealloc rather than krealloc_array because rx_buf is 1055 * accessed as 1 byte entries as well as 4 byte entries so it's 1056 * not necessarily an array. 1057 */ 1058 port->rx_buf = devm_krealloc(uport->dev, port->rx_buf, 1059 port->rx_fifo_depth * sizeof(u32), 1060 GFP_KERNEL); 1061 if (!port->rx_buf) 1062 return -ENOMEM; 1063 } 1064 1065 return 0; 1066 } 1067 1068 1069 static void qcom_geni_serial_shutdown(struct uart_port *uport) 1070 { 1071 disable_irq(uport->irq); 1072 1073 if (uart_console(uport)) 1074 return; 1075 1076 qcom_geni_serial_stop_tx(uport); 1077 qcom_geni_serial_stop_rx(uport); 1078 } 1079 1080 static int qcom_geni_serial_port_setup(struct uart_port *uport) 1081 { 1082 struct qcom_geni_serial_port *port = to_dev_port(uport); 1083 u32 rxstale = DEFAULT_BITS_PER_CHAR * STALE_TIMEOUT; 1084 u32 proto; 1085 u32 pin_swap; 1086 int ret; 1087 1088 proto = geni_se_read_proto(&port->se); 1089 if (proto != GENI_SE_UART) { 1090 dev_err(uport->dev, "Invalid FW loaded, proto: %d\n", proto); 1091 return -ENXIO; 1092 } 1093 1094 qcom_geni_serial_stop_rx(uport); 1095 1096 ret = setup_fifos(port); 1097 if (ret) 1098 return ret; 1099 1100 writel(rxstale, uport->membase + SE_UART_RX_STALE_CNT); 1101 1102 pin_swap = readl(uport->membase + SE_UART_IO_MACRO_CTRL); 1103 if (port->rx_tx_swap) { 1104 pin_swap &= ~DEFAULT_IO_MACRO_IO2_IO3_MASK; 1105 pin_swap |= IO_MACRO_IO2_IO3_SWAP; 1106 } 1107 if (port->cts_rts_swap) { 1108 pin_swap &= ~DEFAULT_IO_MACRO_IO0_IO1_MASK; 1109 pin_swap |= IO_MACRO_IO0_SEL; 1110 } 1111 /* Configure this register if RX-TX, CTS-RTS pins are swapped */ 1112 if (port->rx_tx_swap || port->cts_rts_swap) 1113 writel(pin_swap, uport->membase + SE_UART_IO_MACRO_CTRL); 1114 1115 /* 1116 * Make an unconditional cancel on the main sequencer to reset 1117 * it else we could end up in data loss scenarios. 1118 */ 1119 if (uart_console(uport)) 1120 qcom_geni_serial_poll_tx_done(uport); 1121 geni_se_config_packing(&port->se, BITS_PER_BYTE, BYTES_PER_FIFO_WORD, 1122 false, true, true); 1123 geni_se_init(&port->se, UART_RX_WM, port->rx_fifo_depth - 2); 1124 geni_se_select_mode(&port->se, port->dev_data->mode); 1125 qcom_geni_serial_start_rx(uport); 1126 port->setup = true; 1127 1128 return 0; 1129 } 1130 1131 static int qcom_geni_serial_startup(struct uart_port *uport) 1132 { 1133 int ret; 1134 struct qcom_geni_serial_port *port = to_dev_port(uport); 1135 1136 if (!port->setup) { 1137 ret = qcom_geni_serial_port_setup(uport); 1138 if (ret) 1139 return ret; 1140 } 1141 enable_irq(uport->irq); 1142 1143 return 0; 1144 } 1145 1146 static unsigned long find_clk_rate_in_tol(struct clk *clk, unsigned int desired_clk, 1147 unsigned int *clk_div, unsigned int percent_tol) 1148 { 1149 unsigned long freq; 1150 unsigned long div, maxdiv; 1151 u64 mult; 1152 unsigned long offset, abs_tol, achieved; 1153 1154 abs_tol = div_u64((u64)desired_clk * percent_tol, 100); 1155 maxdiv = CLK_DIV_MSK >> CLK_DIV_SHFT; 1156 div = 1; 1157 while (div <= maxdiv) { 1158 mult = (u64)div * desired_clk; 1159 if (mult != (unsigned long)mult) 1160 break; 1161 1162 offset = div * abs_tol; 1163 freq = clk_round_rate(clk, mult - offset); 1164 1165 /* Can only get lower if we're done */ 1166 if (freq < mult - offset) 1167 break; 1168 1169 /* 1170 * Re-calculate div in case rounding skipped rates but we 1171 * ended up at a good one, then check for a match. 1172 */ 1173 div = DIV_ROUND_CLOSEST(freq, desired_clk); 1174 achieved = DIV_ROUND_CLOSEST(freq, div); 1175 if (achieved <= desired_clk + abs_tol && 1176 achieved >= desired_clk - abs_tol) { 1177 *clk_div = div; 1178 return freq; 1179 } 1180 1181 div = DIV_ROUND_UP(freq, desired_clk); 1182 } 1183 1184 return 0; 1185 } 1186 1187 static unsigned long get_clk_div_rate(struct clk *clk, unsigned int baud, 1188 unsigned int sampling_rate, unsigned int *clk_div) 1189 { 1190 unsigned long ser_clk; 1191 unsigned long desired_clk; 1192 1193 desired_clk = baud * sampling_rate; 1194 if (!desired_clk) 1195 return 0; 1196 1197 /* 1198 * try to find a clock rate within 2% tolerance, then within 5% 1199 */ 1200 ser_clk = find_clk_rate_in_tol(clk, desired_clk, clk_div, 2); 1201 if (!ser_clk) 1202 ser_clk = find_clk_rate_in_tol(clk, desired_clk, clk_div, 5); 1203 1204 return ser_clk; 1205 } 1206 1207 static void qcom_geni_serial_set_termios(struct uart_port *uport, 1208 struct ktermios *termios, 1209 const struct ktermios *old) 1210 { 1211 unsigned int baud; 1212 u32 bits_per_char; 1213 u32 tx_trans_cfg; 1214 u32 tx_parity_cfg; 1215 u32 rx_trans_cfg; 1216 u32 rx_parity_cfg; 1217 u32 stop_bit_len; 1218 unsigned int clk_div; 1219 u32 ser_clk_cfg; 1220 struct qcom_geni_serial_port *port = to_dev_port(uport); 1221 unsigned long clk_rate; 1222 u32 ver, sampling_rate; 1223 unsigned int avg_bw_core; 1224 1225 qcom_geni_serial_stop_rx(uport); 1226 /* baud rate */ 1227 baud = uart_get_baud_rate(uport, termios, old, 300, 4000000); 1228 port->baud = baud; 1229 1230 sampling_rate = UART_OVERSAMPLING; 1231 /* Sampling rate is halved for IP versions >= 2.5 */ 1232 ver = geni_se_get_qup_hw_version(&port->se); 1233 if (ver >= QUP_SE_VERSION_2_5) 1234 sampling_rate /= 2; 1235 1236 clk_rate = get_clk_div_rate(port->se.clk, baud, 1237 sampling_rate, &clk_div); 1238 if (!clk_rate) { 1239 dev_err(port->se.dev, 1240 "Couldn't find suitable clock rate for %u\n", 1241 baud * sampling_rate); 1242 goto out_restart_rx; 1243 } 1244 1245 dev_dbg(port->se.dev, "desired_rate = %u, clk_rate = %lu, clk_div = %u\n", 1246 baud * sampling_rate, clk_rate, clk_div); 1247 1248 uport->uartclk = clk_rate; 1249 port->clk_rate = clk_rate; 1250 dev_pm_opp_set_rate(uport->dev, clk_rate); 1251 ser_clk_cfg = SER_CLK_EN; 1252 ser_clk_cfg |= clk_div << CLK_DIV_SHFT; 1253 1254 /* 1255 * Bump up BW vote on CPU and CORE path as driver supports FIFO mode 1256 * only. 1257 */ 1258 avg_bw_core = (baud > 115200) ? Bps_to_icc(CORE_2X_50_MHZ) 1259 : GENI_DEFAULT_BW; 1260 port->se.icc_paths[GENI_TO_CORE].avg_bw = avg_bw_core; 1261 port->se.icc_paths[CPU_TO_GENI].avg_bw = Bps_to_icc(baud); 1262 geni_icc_set_bw(&port->se); 1263 1264 /* parity */ 1265 tx_trans_cfg = readl(uport->membase + SE_UART_TX_TRANS_CFG); 1266 tx_parity_cfg = readl(uport->membase + SE_UART_TX_PARITY_CFG); 1267 rx_trans_cfg = readl(uport->membase + SE_UART_RX_TRANS_CFG); 1268 rx_parity_cfg = readl(uport->membase + SE_UART_RX_PARITY_CFG); 1269 if (termios->c_cflag & PARENB) { 1270 tx_trans_cfg |= UART_TX_PAR_EN; 1271 rx_trans_cfg |= UART_RX_PAR_EN; 1272 tx_parity_cfg |= PAR_CALC_EN; 1273 rx_parity_cfg |= PAR_CALC_EN; 1274 if (termios->c_cflag & PARODD) { 1275 tx_parity_cfg |= PAR_ODD; 1276 rx_parity_cfg |= PAR_ODD; 1277 } else if (termios->c_cflag & CMSPAR) { 1278 tx_parity_cfg |= PAR_SPACE; 1279 rx_parity_cfg |= PAR_SPACE; 1280 } else { 1281 tx_parity_cfg |= PAR_EVEN; 1282 rx_parity_cfg |= PAR_EVEN; 1283 } 1284 } else { 1285 tx_trans_cfg &= ~UART_TX_PAR_EN; 1286 rx_trans_cfg &= ~UART_RX_PAR_EN; 1287 tx_parity_cfg &= ~PAR_CALC_EN; 1288 rx_parity_cfg &= ~PAR_CALC_EN; 1289 } 1290 1291 /* bits per char */ 1292 bits_per_char = tty_get_char_size(termios->c_cflag); 1293 1294 /* stop bits */ 1295 if (termios->c_cflag & CSTOPB) 1296 stop_bit_len = TX_STOP_BIT_LEN_2; 1297 else 1298 stop_bit_len = TX_STOP_BIT_LEN_1; 1299 1300 /* flow control, clear the CTS_MASK bit if using flow control. */ 1301 if (termios->c_cflag & CRTSCTS) 1302 tx_trans_cfg &= ~UART_CTS_MASK; 1303 else 1304 tx_trans_cfg |= UART_CTS_MASK; 1305 1306 if (baud) 1307 uart_update_timeout(uport, termios->c_cflag, baud); 1308 1309 if (!uart_console(uport)) 1310 writel(port->loopback, 1311 uport->membase + SE_UART_LOOPBACK_CFG); 1312 writel(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); 1313 writel(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); 1314 writel(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); 1315 writel(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); 1316 writel(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); 1317 writel(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); 1318 writel(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); 1319 writel(ser_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG); 1320 writel(ser_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG); 1321 out_restart_rx: 1322 qcom_geni_serial_start_rx(uport); 1323 } 1324 1325 #ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE 1326 static int qcom_geni_console_setup(struct console *co, char *options) 1327 { 1328 struct uart_port *uport; 1329 struct qcom_geni_serial_port *port; 1330 int baud = 115200; 1331 int bits = 8; 1332 int parity = 'n'; 1333 int flow = 'n'; 1334 int ret; 1335 1336 if (co->index >= GENI_UART_CONS_PORTS || co->index < 0) 1337 return -ENXIO; 1338 1339 port = get_port_from_line(co->index, true); 1340 if (IS_ERR(port)) { 1341 pr_err("Invalid line %d\n", co->index); 1342 return PTR_ERR(port); 1343 } 1344 1345 uport = &port->uport; 1346 1347 if (unlikely(!uport->membase)) 1348 return -ENXIO; 1349 1350 if (!port->setup) { 1351 ret = qcom_geni_serial_port_setup(uport); 1352 if (ret) 1353 return ret; 1354 } 1355 1356 if (options) 1357 uart_parse_options(options, &baud, &parity, &bits, &flow); 1358 1359 return uart_set_options(uport, co, baud, parity, bits, flow); 1360 } 1361 1362 static void qcom_geni_serial_earlycon_write(struct console *con, 1363 const char *s, unsigned int n) 1364 { 1365 struct earlycon_device *dev = con->data; 1366 1367 __qcom_geni_serial_console_write(&dev->port, s, n); 1368 } 1369 1370 #ifdef CONFIG_CONSOLE_POLL 1371 static int qcom_geni_serial_earlycon_read(struct console *con, 1372 char *s, unsigned int n) 1373 { 1374 struct earlycon_device *dev = con->data; 1375 struct uart_port *uport = &dev->port; 1376 int num_read = 0; 1377 int ch; 1378 1379 while (num_read < n) { 1380 ch = qcom_geni_serial_get_char(uport); 1381 if (ch == NO_POLL_CHAR) 1382 break; 1383 s[num_read++] = ch; 1384 } 1385 1386 return num_read; 1387 } 1388 1389 static void __init qcom_geni_serial_enable_early_read(struct geni_se *se, 1390 struct console *con) 1391 { 1392 geni_se_setup_s_cmd(se, UART_START_READ, 0); 1393 con->read = qcom_geni_serial_earlycon_read; 1394 } 1395 #else 1396 static inline void qcom_geni_serial_enable_early_read(struct geni_se *se, 1397 struct console *con) { } 1398 #endif 1399 1400 static struct qcom_geni_private_data earlycon_private_data; 1401 1402 static int __init qcom_geni_serial_earlycon_setup(struct earlycon_device *dev, 1403 const char *opt) 1404 { 1405 struct uart_port *uport = &dev->port; 1406 u32 tx_trans_cfg; 1407 u32 tx_parity_cfg = 0; /* Disable Tx Parity */ 1408 u32 rx_trans_cfg = 0; 1409 u32 rx_parity_cfg = 0; /* Disable Rx Parity */ 1410 u32 stop_bit_len = 0; /* Default stop bit length - 1 bit */ 1411 u32 bits_per_char; 1412 struct geni_se se; 1413 1414 if (!uport->membase) 1415 return -EINVAL; 1416 1417 uport->private_data = &earlycon_private_data; 1418 1419 memset(&se, 0, sizeof(se)); 1420 se.base = uport->membase; 1421 if (geni_se_read_proto(&se) != GENI_SE_UART) 1422 return -ENXIO; 1423 /* 1424 * Ignore Flow control. 1425 * n = 8. 1426 */ 1427 tx_trans_cfg = UART_CTS_MASK; 1428 bits_per_char = BITS_PER_BYTE; 1429 1430 /* 1431 * Make an unconditional cancel on the main sequencer to reset 1432 * it else we could end up in data loss scenarios. 1433 */ 1434 qcom_geni_serial_poll_tx_done(uport); 1435 qcom_geni_serial_abort_rx(uport); 1436 geni_se_config_packing(&se, BITS_PER_BYTE, BYTES_PER_FIFO_WORD, 1437 false, true, true); 1438 geni_se_init(&se, DEF_FIFO_DEPTH_WORDS / 2, DEF_FIFO_DEPTH_WORDS - 2); 1439 geni_se_select_mode(&se, GENI_SE_FIFO); 1440 1441 writel(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG); 1442 writel(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG); 1443 writel(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG); 1444 writel(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG); 1445 writel(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN); 1446 writel(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN); 1447 writel(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN); 1448 1449 dev->con->write = qcom_geni_serial_earlycon_write; 1450 dev->con->setup = NULL; 1451 qcom_geni_serial_enable_early_read(&se, dev->con); 1452 1453 return 0; 1454 } 1455 OF_EARLYCON_DECLARE(qcom_geni, "qcom,geni-debug-uart", 1456 qcom_geni_serial_earlycon_setup); 1457 1458 static int __init console_register(struct uart_driver *drv) 1459 { 1460 return uart_register_driver(drv); 1461 } 1462 1463 static void console_unregister(struct uart_driver *drv) 1464 { 1465 uart_unregister_driver(drv); 1466 } 1467 1468 static struct console cons_ops = { 1469 .name = "ttyMSM", 1470 .write = qcom_geni_serial_console_write, 1471 .device = uart_console_device, 1472 .setup = qcom_geni_console_setup, 1473 .flags = CON_PRINTBUFFER, 1474 .index = -1, 1475 .data = &qcom_geni_console_driver, 1476 }; 1477 1478 static struct uart_driver qcom_geni_console_driver = { 1479 .owner = THIS_MODULE, 1480 .driver_name = "qcom_geni_console", 1481 .dev_name = "ttyMSM", 1482 .nr = GENI_UART_CONS_PORTS, 1483 .cons = &cons_ops, 1484 }; 1485 #else 1486 static int console_register(struct uart_driver *drv) 1487 { 1488 return 0; 1489 } 1490 1491 static void console_unregister(struct uart_driver *drv) 1492 { 1493 } 1494 #endif /* CONFIG_SERIAL_QCOM_GENI_CONSOLE */ 1495 1496 static struct uart_driver qcom_geni_uart_driver = { 1497 .owner = THIS_MODULE, 1498 .driver_name = "qcom_geni_uart", 1499 .dev_name = "ttyHS", 1500 .nr = GENI_UART_PORTS, 1501 }; 1502 1503 static void qcom_geni_serial_pm(struct uart_port *uport, 1504 unsigned int new_state, unsigned int old_state) 1505 { 1506 struct qcom_geni_serial_port *port = to_dev_port(uport); 1507 1508 /* If we've never been called, treat it as off */ 1509 if (old_state == UART_PM_STATE_UNDEFINED) 1510 old_state = UART_PM_STATE_OFF; 1511 1512 if (new_state == UART_PM_STATE_ON && old_state == UART_PM_STATE_OFF) { 1513 geni_icc_enable(&port->se); 1514 if (port->clk_rate) 1515 dev_pm_opp_set_rate(uport->dev, port->clk_rate); 1516 geni_se_resources_on(&port->se); 1517 } else if (new_state == UART_PM_STATE_OFF && 1518 old_state == UART_PM_STATE_ON) { 1519 geni_se_resources_off(&port->se); 1520 dev_pm_opp_set_rate(uport->dev, 0); 1521 geni_icc_disable(&port->se); 1522 } 1523 } 1524 1525 static const struct uart_ops qcom_geni_console_pops = { 1526 .tx_empty = qcom_geni_serial_tx_empty, 1527 .stop_tx = qcom_geni_serial_stop_tx_fifo, 1528 .start_tx = qcom_geni_serial_start_tx_fifo, 1529 .stop_rx = qcom_geni_serial_stop_rx_fifo, 1530 .start_rx = qcom_geni_serial_start_rx_fifo, 1531 .set_termios = qcom_geni_serial_set_termios, 1532 .startup = qcom_geni_serial_startup, 1533 .request_port = qcom_geni_serial_request_port, 1534 .config_port = qcom_geni_serial_config_port, 1535 .shutdown = qcom_geni_serial_shutdown, 1536 .type = qcom_geni_serial_get_type, 1537 .set_mctrl = qcom_geni_serial_set_mctrl, 1538 .get_mctrl = qcom_geni_serial_get_mctrl, 1539 #ifdef CONFIG_CONSOLE_POLL 1540 .poll_get_char = qcom_geni_serial_get_char, 1541 .poll_put_char = qcom_geni_serial_poll_put_char, 1542 .poll_init = qcom_geni_serial_port_setup, 1543 #endif 1544 .pm = qcom_geni_serial_pm, 1545 }; 1546 1547 static const struct uart_ops qcom_geni_uart_pops = { 1548 .tx_empty = qcom_geni_serial_tx_empty, 1549 .stop_tx = qcom_geni_serial_stop_tx_dma, 1550 .start_tx = qcom_geni_serial_start_tx_dma, 1551 .start_rx = qcom_geni_serial_start_rx_dma, 1552 .stop_rx = qcom_geni_serial_stop_rx_dma, 1553 .set_termios = qcom_geni_serial_set_termios, 1554 .startup = qcom_geni_serial_startup, 1555 .request_port = qcom_geni_serial_request_port, 1556 .config_port = qcom_geni_serial_config_port, 1557 .shutdown = qcom_geni_serial_shutdown, 1558 .type = qcom_geni_serial_get_type, 1559 .set_mctrl = qcom_geni_serial_set_mctrl, 1560 .get_mctrl = qcom_geni_serial_get_mctrl, 1561 .pm = qcom_geni_serial_pm, 1562 }; 1563 1564 static int qcom_geni_serial_probe(struct platform_device *pdev) 1565 { 1566 int ret = 0; 1567 int line; 1568 struct qcom_geni_serial_port *port; 1569 struct uart_port *uport; 1570 struct resource *res; 1571 int irq; 1572 struct uart_driver *drv; 1573 const struct qcom_geni_device_data *data; 1574 1575 data = of_device_get_match_data(&pdev->dev); 1576 if (!data) 1577 return -EINVAL; 1578 1579 if (data->console) { 1580 drv = &qcom_geni_console_driver; 1581 line = of_alias_get_id(pdev->dev.of_node, "serial"); 1582 } else { 1583 drv = &qcom_geni_uart_driver; 1584 line = of_alias_get_id(pdev->dev.of_node, "serial"); 1585 if (line == -ENODEV) /* compat with non-standard aliases */ 1586 line = of_alias_get_id(pdev->dev.of_node, "hsuart"); 1587 } 1588 1589 port = get_port_from_line(line, data->console); 1590 if (IS_ERR(port)) { 1591 dev_err(&pdev->dev, "Invalid line %d\n", line); 1592 return PTR_ERR(port); 1593 } 1594 1595 uport = &port->uport; 1596 /* Don't allow 2 drivers to access the same port */ 1597 if (uport->private_data) 1598 return -ENODEV; 1599 1600 uport->dev = &pdev->dev; 1601 port->dev_data = data; 1602 port->se.dev = &pdev->dev; 1603 port->se.wrapper = dev_get_drvdata(pdev->dev.parent); 1604 port->se.clk = devm_clk_get(&pdev->dev, "se"); 1605 if (IS_ERR(port->se.clk)) { 1606 ret = PTR_ERR(port->se.clk); 1607 dev_err(&pdev->dev, "Err getting SE Core clk %d\n", ret); 1608 return ret; 1609 } 1610 1611 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1612 if (!res) 1613 return -EINVAL; 1614 uport->mapbase = res->start; 1615 1616 port->tx_fifo_depth = DEF_FIFO_DEPTH_WORDS; 1617 port->rx_fifo_depth = DEF_FIFO_DEPTH_WORDS; 1618 port->tx_fifo_width = DEF_FIFO_WIDTH_BITS; 1619 1620 if (!data->console) { 1621 port->rx_buf = devm_kzalloc(uport->dev, 1622 DMA_RX_BUF_SIZE, GFP_KERNEL); 1623 if (!port->rx_buf) 1624 return -ENOMEM; 1625 } 1626 1627 ret = geni_icc_get(&port->se, NULL); 1628 if (ret) 1629 return ret; 1630 port->se.icc_paths[GENI_TO_CORE].avg_bw = GENI_DEFAULT_BW; 1631 port->se.icc_paths[CPU_TO_GENI].avg_bw = GENI_DEFAULT_BW; 1632 1633 /* Set BW for register access */ 1634 ret = geni_icc_set_bw(&port->se); 1635 if (ret) 1636 return ret; 1637 1638 port->name = devm_kasprintf(uport->dev, GFP_KERNEL, 1639 "qcom_geni_serial_%s%d", 1640 uart_console(uport) ? "console" : "uart", uport->line); 1641 if (!port->name) 1642 return -ENOMEM; 1643 1644 irq = platform_get_irq(pdev, 0); 1645 if (irq < 0) 1646 return irq; 1647 uport->irq = irq; 1648 uport->has_sysrq = IS_ENABLED(CONFIG_SERIAL_QCOM_GENI_CONSOLE); 1649 1650 if (!data->console) 1651 port->wakeup_irq = platform_get_irq_optional(pdev, 1); 1652 1653 if (of_property_read_bool(pdev->dev.of_node, "rx-tx-swap")) 1654 port->rx_tx_swap = true; 1655 1656 if (of_property_read_bool(pdev->dev.of_node, "cts-rts-swap")) 1657 port->cts_rts_swap = true; 1658 1659 ret = devm_pm_opp_set_clkname(&pdev->dev, "se"); 1660 if (ret) 1661 return ret; 1662 /* OPP table is optional */ 1663 ret = devm_pm_opp_of_add_table(&pdev->dev); 1664 if (ret && ret != -ENODEV) { 1665 dev_err(&pdev->dev, "invalid OPP table in device tree\n"); 1666 return ret; 1667 } 1668 1669 port->private_data.drv = drv; 1670 uport->private_data = &port->private_data; 1671 platform_set_drvdata(pdev, port); 1672 1673 irq_set_status_flags(uport->irq, IRQ_NOAUTOEN); 1674 ret = devm_request_irq(uport->dev, uport->irq, qcom_geni_serial_isr, 1675 IRQF_TRIGGER_HIGH, port->name, uport); 1676 if (ret) { 1677 dev_err(uport->dev, "Failed to get IRQ ret %d\n", ret); 1678 return ret; 1679 } 1680 1681 ret = uart_add_one_port(drv, uport); 1682 if (ret) 1683 return ret; 1684 1685 if (port->wakeup_irq > 0) { 1686 device_init_wakeup(&pdev->dev, true); 1687 ret = dev_pm_set_dedicated_wake_irq(&pdev->dev, 1688 port->wakeup_irq); 1689 if (ret) { 1690 device_init_wakeup(&pdev->dev, false); 1691 uart_remove_one_port(drv, uport); 1692 return ret; 1693 } 1694 } 1695 1696 return 0; 1697 } 1698 1699 static int qcom_geni_serial_remove(struct platform_device *pdev) 1700 { 1701 struct qcom_geni_serial_port *port = platform_get_drvdata(pdev); 1702 struct uart_driver *drv = port->private_data.drv; 1703 1704 dev_pm_clear_wake_irq(&pdev->dev); 1705 device_init_wakeup(&pdev->dev, false); 1706 uart_remove_one_port(drv, &port->uport); 1707 1708 return 0; 1709 } 1710 1711 static int qcom_geni_serial_sys_suspend(struct device *dev) 1712 { 1713 struct qcom_geni_serial_port *port = dev_get_drvdata(dev); 1714 struct uart_port *uport = &port->uport; 1715 struct qcom_geni_private_data *private_data = uport->private_data; 1716 1717 /* 1718 * This is done so we can hit the lowest possible state in suspend 1719 * even with no_console_suspend 1720 */ 1721 if (uart_console(uport)) { 1722 geni_icc_set_tag(&port->se, QCOM_ICC_TAG_ACTIVE_ONLY); 1723 geni_icc_set_bw(&port->se); 1724 } 1725 return uart_suspend_port(private_data->drv, uport); 1726 } 1727 1728 static int qcom_geni_serial_sys_resume(struct device *dev) 1729 { 1730 int ret; 1731 struct qcom_geni_serial_port *port = dev_get_drvdata(dev); 1732 struct uart_port *uport = &port->uport; 1733 struct qcom_geni_private_data *private_data = uport->private_data; 1734 1735 ret = uart_resume_port(private_data->drv, uport); 1736 if (uart_console(uport)) { 1737 geni_icc_set_tag(&port->se, QCOM_ICC_TAG_ALWAYS); 1738 geni_icc_set_bw(&port->se); 1739 } 1740 return ret; 1741 } 1742 1743 static int qcom_geni_serial_sys_hib_resume(struct device *dev) 1744 { 1745 int ret = 0; 1746 struct uart_port *uport; 1747 struct qcom_geni_private_data *private_data; 1748 struct qcom_geni_serial_port *port = dev_get_drvdata(dev); 1749 1750 uport = &port->uport; 1751 private_data = uport->private_data; 1752 1753 if (uart_console(uport)) { 1754 geni_icc_set_tag(&port->se, QCOM_ICC_TAG_ALWAYS); 1755 geni_icc_set_bw(&port->se); 1756 ret = uart_resume_port(private_data->drv, uport); 1757 /* 1758 * For hibernation usecase clients for 1759 * console UART won't call port setup during restore, 1760 * hence call port setup for console uart. 1761 */ 1762 qcom_geni_serial_port_setup(uport); 1763 } else { 1764 /* 1765 * Peripheral register settings are lost during hibernation. 1766 * Update setup flag such that port setup happens again 1767 * during next session. Clients of HS-UART will close and 1768 * open the port during hibernation. 1769 */ 1770 port->setup = false; 1771 } 1772 return ret; 1773 } 1774 1775 static const struct qcom_geni_device_data qcom_geni_console_data = { 1776 .console = true, 1777 .mode = GENI_SE_FIFO, 1778 }; 1779 1780 static const struct qcom_geni_device_data qcom_geni_uart_data = { 1781 .console = false, 1782 .mode = GENI_SE_DMA, 1783 }; 1784 1785 static const struct dev_pm_ops qcom_geni_serial_pm_ops = { 1786 .suspend = pm_sleep_ptr(qcom_geni_serial_sys_suspend), 1787 .resume = pm_sleep_ptr(qcom_geni_serial_sys_resume), 1788 .freeze = pm_sleep_ptr(qcom_geni_serial_sys_suspend), 1789 .poweroff = pm_sleep_ptr(qcom_geni_serial_sys_suspend), 1790 .restore = pm_sleep_ptr(qcom_geni_serial_sys_hib_resume), 1791 .thaw = pm_sleep_ptr(qcom_geni_serial_sys_hib_resume), 1792 }; 1793 1794 static const struct of_device_id qcom_geni_serial_match_table[] = { 1795 { 1796 .compatible = "qcom,geni-debug-uart", 1797 .data = &qcom_geni_console_data, 1798 }, 1799 { 1800 .compatible = "qcom,geni-uart", 1801 .data = &qcom_geni_uart_data, 1802 }, 1803 {} 1804 }; 1805 MODULE_DEVICE_TABLE(of, qcom_geni_serial_match_table); 1806 1807 static struct platform_driver qcom_geni_serial_platform_driver = { 1808 .remove = qcom_geni_serial_remove, 1809 .probe = qcom_geni_serial_probe, 1810 .driver = { 1811 .name = "qcom_geni_serial", 1812 .of_match_table = qcom_geni_serial_match_table, 1813 .pm = &qcom_geni_serial_pm_ops, 1814 }, 1815 }; 1816 1817 static int __init qcom_geni_serial_init(void) 1818 { 1819 int ret; 1820 1821 ret = console_register(&qcom_geni_console_driver); 1822 if (ret) 1823 return ret; 1824 1825 ret = uart_register_driver(&qcom_geni_uart_driver); 1826 if (ret) { 1827 console_unregister(&qcom_geni_console_driver); 1828 return ret; 1829 } 1830 1831 ret = platform_driver_register(&qcom_geni_serial_platform_driver); 1832 if (ret) { 1833 console_unregister(&qcom_geni_console_driver); 1834 uart_unregister_driver(&qcom_geni_uart_driver); 1835 } 1836 return ret; 1837 } 1838 module_init(qcom_geni_serial_init); 1839 1840 static void __exit qcom_geni_serial_exit(void) 1841 { 1842 platform_driver_unregister(&qcom_geni_serial_platform_driver); 1843 console_unregister(&qcom_geni_console_driver); 1844 uart_unregister_driver(&qcom_geni_uart_driver); 1845 } 1846 module_exit(qcom_geni_serial_exit); 1847 1848 MODULE_DESCRIPTION("Serial driver for GENI based QUP cores"); 1849 MODULE_LICENSE("GPL v2"); 1850