1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Driver for OMAP-UART controller. 4 * Based on drivers/serial/8250.c 5 * 6 * Copyright (C) 2010 Texas Instruments. 7 * 8 * Authors: 9 * Govindraj R <govindraj.raja@ti.com> 10 * Thara Gopinath <thara@ti.com> 11 * 12 * Note: This driver is made separate from 8250 driver as we cannot 13 * over load 8250 driver with omap platform specific configuration for 14 * features like DMA, it makes easier to implement features like DMA and 15 * hardware flow control and software flow control configuration with 16 * this driver as required for the omap-platform. 17 */ 18 19 #include <linux/module.h> 20 #include <linux/init.h> 21 #include <linux/console.h> 22 #include <linux/serial_reg.h> 23 #include <linux/delay.h> 24 #include <linux/slab.h> 25 #include <linux/tty.h> 26 #include <linux/tty_flip.h> 27 #include <linux/platform_device.h> 28 #include <linux/io.h> 29 #include <linux/clk.h> 30 #include <linux/serial_core.h> 31 #include <linux/irq.h> 32 #include <linux/pm_runtime.h> 33 #include <linux/pm_wakeirq.h> 34 #include <linux/of.h> 35 #include <linux/of_irq.h> 36 #include <linux/gpio/consumer.h> 37 #include <linux/platform_data/serial-omap.h> 38 39 #define OMAP_MAX_HSUART_PORTS 10 40 41 #define UART_BUILD_REVISION(x, y) (((x) << 8) | (y)) 42 43 #define OMAP_UART_REV_42 0x0402 44 #define OMAP_UART_REV_46 0x0406 45 #define OMAP_UART_REV_52 0x0502 46 #define OMAP_UART_REV_63 0x0603 47 48 #define OMAP_UART_TX_WAKEUP_EN BIT(7) 49 50 /* Feature flags */ 51 #define OMAP_UART_WER_HAS_TX_WAKEUP BIT(0) 52 53 #define UART_ERRATA_i202_MDR1_ACCESS BIT(0) 54 #define UART_ERRATA_i291_DMA_FORCEIDLE BIT(1) 55 56 #define DEFAULT_CLK_SPEED 48000000 /* 48Mhz */ 57 58 /* SCR register bitmasks */ 59 #define OMAP_UART_SCR_RX_TRIG_GRANU1_MASK (1 << 7) 60 #define OMAP_UART_SCR_TX_TRIG_GRANU1_MASK (1 << 6) 61 #define OMAP_UART_SCR_TX_EMPTY (1 << 3) 62 63 /* FCR register bitmasks */ 64 #define OMAP_UART_FCR_RX_FIFO_TRIG_MASK (0x3 << 6) 65 #define OMAP_UART_FCR_TX_FIFO_TRIG_MASK (0x3 << 4) 66 67 /* MVR register bitmasks */ 68 #define OMAP_UART_MVR_SCHEME_SHIFT 30 69 70 #define OMAP_UART_LEGACY_MVR_MAJ_MASK 0xf0 71 #define OMAP_UART_LEGACY_MVR_MAJ_SHIFT 4 72 #define OMAP_UART_LEGACY_MVR_MIN_MASK 0x0f 73 74 #define OMAP_UART_MVR_MAJ_MASK 0x700 75 #define OMAP_UART_MVR_MAJ_SHIFT 8 76 #define OMAP_UART_MVR_MIN_MASK 0x3f 77 78 #define OMAP_UART_DMA_CH_FREE -1 79 80 #define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA 81 #define OMAP_MODE13X_SPEED 230400 82 83 /* WER = 0x7F 84 * Enable module level wakeup in WER reg 85 */ 86 #define OMAP_UART_WER_MOD_WKUP 0x7F 87 88 /* Enable XON/XOFF flow control on output */ 89 #define OMAP_UART_SW_TX 0x08 90 91 /* Enable XON/XOFF flow control on input */ 92 #define OMAP_UART_SW_RX 0x02 93 94 #define OMAP_UART_SW_CLR 0xF0 95 96 #define OMAP_UART_TCR_TRIG 0x0F 97 98 struct uart_omap_dma { 99 u8 uart_dma_tx; 100 u8 uart_dma_rx; 101 int rx_dma_channel; 102 int tx_dma_channel; 103 dma_addr_t rx_buf_dma_phys; 104 dma_addr_t tx_buf_dma_phys; 105 unsigned int uart_base; 106 /* 107 * Buffer for rx dma. It is not required for tx because the buffer 108 * comes from port structure. 109 */ 110 unsigned char *rx_buf; 111 unsigned int prev_rx_dma_pos; 112 int tx_buf_size; 113 int tx_dma_used; 114 int rx_dma_used; 115 spinlock_t tx_lock; 116 spinlock_t rx_lock; 117 /* timer to poll activity on rx dma */ 118 struct timer_list rx_timer; 119 unsigned int rx_buf_size; 120 unsigned int rx_poll_rate; 121 unsigned int rx_timeout; 122 }; 123 124 struct uart_omap_port { 125 struct uart_port port; 126 struct uart_omap_dma uart_dma; 127 struct device *dev; 128 int wakeirq; 129 130 unsigned char ier; 131 unsigned char lcr; 132 unsigned char mcr; 133 unsigned char fcr; 134 unsigned char efr; 135 unsigned char dll; 136 unsigned char dlh; 137 unsigned char mdr1; 138 unsigned char scr; 139 unsigned char wer; 140 141 int use_dma; 142 /* 143 * Some bits in registers are cleared on a read, so they must 144 * be saved whenever the register is read, but the bits will not 145 * be immediately processed. 146 */ 147 unsigned int lsr_break_flag; 148 unsigned char msr_saved_flags; 149 char name[20]; 150 unsigned long port_activity; 151 int context_loss_cnt; 152 u32 errata; 153 u32 features; 154 155 struct gpio_desc *rts_gpiod; 156 157 struct pm_qos_request pm_qos_request; 158 u32 latency; 159 u32 calc_latency; 160 struct work_struct qos_work; 161 bool is_suspending; 162 163 unsigned int rs485_tx_filter_count; 164 }; 165 166 #define to_uart_omap_port(p) ((container_of((p), struct uart_omap_port, port))) 167 168 static struct uart_omap_port *ui[OMAP_MAX_HSUART_PORTS]; 169 170 /* Forward declaration of functions */ 171 static void serial_omap_mdr1_errataset(struct uart_omap_port *up, u8 mdr1); 172 173 static inline unsigned int serial_in(struct uart_omap_port *up, int offset) 174 { 175 offset <<= up->port.regshift; 176 return readw(up->port.membase + offset); 177 } 178 179 static inline void serial_out(struct uart_omap_port *up, int offset, int value) 180 { 181 offset <<= up->port.regshift; 182 writew(value, up->port.membase + offset); 183 } 184 185 static inline void serial_omap_clear_fifos(struct uart_omap_port *up) 186 { 187 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); 188 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | 189 UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); 190 serial_out(up, UART_FCR, 0); 191 } 192 193 #ifdef CONFIG_PM 194 static int serial_omap_get_context_loss_count(struct uart_omap_port *up) 195 { 196 struct omap_uart_port_info *pdata = dev_get_platdata(up->dev); 197 198 if (!pdata || !pdata->get_context_loss_count) 199 return -EINVAL; 200 201 return pdata->get_context_loss_count(up->dev); 202 } 203 204 /* REVISIT: Remove this when omap3 boots in device tree only mode */ 205 static void serial_omap_enable_wakeup(struct uart_omap_port *up, bool enable) 206 { 207 struct omap_uart_port_info *pdata = dev_get_platdata(up->dev); 208 209 if (!pdata || !pdata->enable_wakeup) 210 return; 211 212 pdata->enable_wakeup(up->dev, enable); 213 } 214 #endif /* CONFIG_PM */ 215 216 /* 217 * Calculate the absolute difference between the desired and actual baud 218 * rate for the given mode. 219 */ 220 static inline int calculate_baud_abs_diff(struct uart_port *port, 221 unsigned int baud, unsigned int mode) 222 { 223 unsigned int n = port->uartclk / (mode * baud); 224 int abs_diff; 225 226 if (n == 0) 227 n = 1; 228 229 abs_diff = baud - (port->uartclk / (mode * n)); 230 if (abs_diff < 0) 231 abs_diff = -abs_diff; 232 233 return abs_diff; 234 } 235 236 /* 237 * serial_omap_baud_is_mode16 - check if baud rate is MODE16X 238 * @port: uart port info 239 * @baud: baudrate for which mode needs to be determined 240 * 241 * Returns true if baud rate is MODE16X and false if MODE13X 242 * Original table in OMAP TRM named "UART Mode Baud Rates, Divisor Values, 243 * and Error Rates" determines modes not for all common baud rates. 244 * E.g. for 1000000 baud rate mode must be 16x, but according to that 245 * table it's determined as 13x. 246 */ 247 static bool 248 serial_omap_baud_is_mode16(struct uart_port *port, unsigned int baud) 249 { 250 int abs_diff_13 = calculate_baud_abs_diff(port, baud, 13); 251 int abs_diff_16 = calculate_baud_abs_diff(port, baud, 16); 252 253 return (abs_diff_13 >= abs_diff_16); 254 } 255 256 /* 257 * serial_omap_get_divisor - calculate divisor value 258 * @port: uart port info 259 * @baud: baudrate for which divisor needs to be calculated. 260 */ 261 static unsigned int 262 serial_omap_get_divisor(struct uart_port *port, unsigned int baud) 263 { 264 unsigned int mode; 265 266 if (!serial_omap_baud_is_mode16(port, baud)) 267 mode = 13; 268 else 269 mode = 16; 270 return port->uartclk/(mode * baud); 271 } 272 273 static void serial_omap_enable_ms(struct uart_port *port) 274 { 275 struct uart_omap_port *up = to_uart_omap_port(port); 276 277 dev_dbg(up->port.dev, "serial_omap_enable_ms+%d\n", up->port.line); 278 279 pm_runtime_get_sync(up->dev); 280 up->ier |= UART_IER_MSI; 281 serial_out(up, UART_IER, up->ier); 282 pm_runtime_mark_last_busy(up->dev); 283 pm_runtime_put_autosuspend(up->dev); 284 } 285 286 static void serial_omap_stop_tx(struct uart_port *port) 287 { 288 struct uart_omap_port *up = to_uart_omap_port(port); 289 int res; 290 291 pm_runtime_get_sync(up->dev); 292 293 /* Handle RS-485 */ 294 if (port->rs485.flags & SER_RS485_ENABLED) { 295 if (up->scr & OMAP_UART_SCR_TX_EMPTY) { 296 /* THR interrupt is fired when both TX FIFO and TX 297 * shift register are empty. This means there's nothing 298 * left to transmit now, so make sure the THR interrupt 299 * is fired when TX FIFO is below the trigger level, 300 * disable THR interrupts and toggle the RS-485 GPIO 301 * data direction pin if needed. 302 */ 303 up->scr &= ~OMAP_UART_SCR_TX_EMPTY; 304 serial_out(up, UART_OMAP_SCR, up->scr); 305 res = (port->rs485.flags & SER_RS485_RTS_AFTER_SEND) ? 306 1 : 0; 307 if (up->rts_gpiod && 308 gpiod_get_value(up->rts_gpiod) != res) { 309 if (port->rs485.delay_rts_after_send > 0) 310 mdelay( 311 port->rs485.delay_rts_after_send); 312 gpiod_set_value(up->rts_gpiod, res); 313 } 314 } else { 315 /* We're asked to stop, but there's still stuff in the 316 * UART FIFO, so make sure the THR interrupt is fired 317 * when both TX FIFO and TX shift register are empty. 318 * The next THR interrupt (if no transmission is started 319 * in the meantime) will indicate the end of a 320 * transmission. Therefore we _don't_ disable THR 321 * interrupts in this situation. 322 */ 323 up->scr |= OMAP_UART_SCR_TX_EMPTY; 324 serial_out(up, UART_OMAP_SCR, up->scr); 325 return; 326 } 327 } 328 329 if (up->ier & UART_IER_THRI) { 330 up->ier &= ~UART_IER_THRI; 331 serial_out(up, UART_IER, up->ier); 332 } 333 334 pm_runtime_mark_last_busy(up->dev); 335 pm_runtime_put_autosuspend(up->dev); 336 } 337 338 static void serial_omap_stop_rx(struct uart_port *port) 339 { 340 struct uart_omap_port *up = to_uart_omap_port(port); 341 342 pm_runtime_get_sync(up->dev); 343 up->ier &= ~(UART_IER_RLSI | UART_IER_RDI); 344 up->port.read_status_mask &= ~UART_LSR_DR; 345 serial_out(up, UART_IER, up->ier); 346 pm_runtime_mark_last_busy(up->dev); 347 pm_runtime_put_autosuspend(up->dev); 348 } 349 350 static void transmit_chars(struct uart_omap_port *up, unsigned int lsr) 351 { 352 struct circ_buf *xmit = &up->port.state->xmit; 353 int count; 354 355 if (up->port.x_char) { 356 serial_out(up, UART_TX, up->port.x_char); 357 up->port.icount.tx++; 358 up->port.x_char = 0; 359 if ((up->port.rs485.flags & SER_RS485_ENABLED) && 360 !(up->port.rs485.flags & SER_RS485_RX_DURING_TX)) 361 up->rs485_tx_filter_count++; 362 363 return; 364 } 365 if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) { 366 serial_omap_stop_tx(&up->port); 367 return; 368 } 369 count = up->port.fifosize / 4; 370 do { 371 serial_out(up, UART_TX, xmit->buf[xmit->tail]); 372 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 373 up->port.icount.tx++; 374 if ((up->port.rs485.flags & SER_RS485_ENABLED) && 375 !(up->port.rs485.flags & SER_RS485_RX_DURING_TX)) 376 up->rs485_tx_filter_count++; 377 378 if (uart_circ_empty(xmit)) 379 break; 380 } while (--count > 0); 381 382 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 383 uart_write_wakeup(&up->port); 384 385 if (uart_circ_empty(xmit)) 386 serial_omap_stop_tx(&up->port); 387 } 388 389 static inline void serial_omap_enable_ier_thri(struct uart_omap_port *up) 390 { 391 if (!(up->ier & UART_IER_THRI)) { 392 up->ier |= UART_IER_THRI; 393 serial_out(up, UART_IER, up->ier); 394 } 395 } 396 397 static void serial_omap_start_tx(struct uart_port *port) 398 { 399 struct uart_omap_port *up = to_uart_omap_port(port); 400 int res; 401 402 pm_runtime_get_sync(up->dev); 403 404 /* Handle RS-485 */ 405 if (port->rs485.flags & SER_RS485_ENABLED) { 406 /* Fire THR interrupts when FIFO is below trigger level */ 407 up->scr &= ~OMAP_UART_SCR_TX_EMPTY; 408 serial_out(up, UART_OMAP_SCR, up->scr); 409 410 /* if rts not already enabled */ 411 res = (port->rs485.flags & SER_RS485_RTS_ON_SEND) ? 1 : 0; 412 if (up->rts_gpiod && gpiod_get_value(up->rts_gpiod) != res) { 413 gpiod_set_value(up->rts_gpiod, res); 414 if (port->rs485.delay_rts_before_send > 0) 415 mdelay(port->rs485.delay_rts_before_send); 416 } 417 } 418 419 if ((port->rs485.flags & SER_RS485_ENABLED) && 420 !(port->rs485.flags & SER_RS485_RX_DURING_TX)) 421 up->rs485_tx_filter_count = 0; 422 423 serial_omap_enable_ier_thri(up); 424 pm_runtime_mark_last_busy(up->dev); 425 pm_runtime_put_autosuspend(up->dev); 426 } 427 428 static void serial_omap_throttle(struct uart_port *port) 429 { 430 struct uart_omap_port *up = to_uart_omap_port(port); 431 unsigned long flags; 432 433 pm_runtime_get_sync(up->dev); 434 spin_lock_irqsave(&up->port.lock, flags); 435 up->ier &= ~(UART_IER_RLSI | UART_IER_RDI); 436 serial_out(up, UART_IER, up->ier); 437 spin_unlock_irqrestore(&up->port.lock, flags); 438 pm_runtime_mark_last_busy(up->dev); 439 pm_runtime_put_autosuspend(up->dev); 440 } 441 442 static void serial_omap_unthrottle(struct uart_port *port) 443 { 444 struct uart_omap_port *up = to_uart_omap_port(port); 445 unsigned long flags; 446 447 pm_runtime_get_sync(up->dev); 448 spin_lock_irqsave(&up->port.lock, flags); 449 up->ier |= UART_IER_RLSI | UART_IER_RDI; 450 serial_out(up, UART_IER, up->ier); 451 spin_unlock_irqrestore(&up->port.lock, flags); 452 pm_runtime_mark_last_busy(up->dev); 453 pm_runtime_put_autosuspend(up->dev); 454 } 455 456 static unsigned int check_modem_status(struct uart_omap_port *up) 457 { 458 unsigned int status; 459 460 status = serial_in(up, UART_MSR); 461 status |= up->msr_saved_flags; 462 up->msr_saved_flags = 0; 463 if ((status & UART_MSR_ANY_DELTA) == 0) 464 return status; 465 466 if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI && 467 up->port.state != NULL) { 468 if (status & UART_MSR_TERI) 469 up->port.icount.rng++; 470 if (status & UART_MSR_DDSR) 471 up->port.icount.dsr++; 472 if (status & UART_MSR_DDCD) 473 uart_handle_dcd_change 474 (&up->port, status & UART_MSR_DCD); 475 if (status & UART_MSR_DCTS) 476 uart_handle_cts_change 477 (&up->port, status & UART_MSR_CTS); 478 wake_up_interruptible(&up->port.state->port.delta_msr_wait); 479 } 480 481 return status; 482 } 483 484 static void serial_omap_rlsi(struct uart_omap_port *up, unsigned int lsr) 485 { 486 unsigned int flag; 487 488 /* 489 * Read one data character out to avoid stalling the receiver according 490 * to the table 23-246 of the omap4 TRM. 491 */ 492 if (likely(lsr & UART_LSR_DR)) { 493 serial_in(up, UART_RX); 494 if ((up->port.rs485.flags & SER_RS485_ENABLED) && 495 !(up->port.rs485.flags & SER_RS485_RX_DURING_TX) && 496 up->rs485_tx_filter_count) 497 up->rs485_tx_filter_count--; 498 } 499 500 up->port.icount.rx++; 501 flag = TTY_NORMAL; 502 503 if (lsr & UART_LSR_BI) { 504 flag = TTY_BREAK; 505 lsr &= ~(UART_LSR_FE | UART_LSR_PE); 506 up->port.icount.brk++; 507 /* 508 * We do the SysRQ and SAK checking 509 * here because otherwise the break 510 * may get masked by ignore_status_mask 511 * or read_status_mask. 512 */ 513 if (uart_handle_break(&up->port)) 514 return; 515 516 } 517 518 if (lsr & UART_LSR_PE) { 519 flag = TTY_PARITY; 520 up->port.icount.parity++; 521 } 522 523 if (lsr & UART_LSR_FE) { 524 flag = TTY_FRAME; 525 up->port.icount.frame++; 526 } 527 528 if (lsr & UART_LSR_OE) 529 up->port.icount.overrun++; 530 531 #ifdef CONFIG_SERIAL_OMAP_CONSOLE 532 if (up->port.line == up->port.cons->index) { 533 /* Recover the break flag from console xmit */ 534 lsr |= up->lsr_break_flag; 535 } 536 #endif 537 uart_insert_char(&up->port, lsr, UART_LSR_OE, 0, flag); 538 } 539 540 static void serial_omap_rdi(struct uart_omap_port *up, unsigned int lsr) 541 { 542 unsigned char ch = 0; 543 unsigned int flag; 544 545 if (!(lsr & UART_LSR_DR)) 546 return; 547 548 ch = serial_in(up, UART_RX); 549 if ((up->port.rs485.flags & SER_RS485_ENABLED) && 550 !(up->port.rs485.flags & SER_RS485_RX_DURING_TX) && 551 up->rs485_tx_filter_count) { 552 up->rs485_tx_filter_count--; 553 return; 554 } 555 556 flag = TTY_NORMAL; 557 up->port.icount.rx++; 558 559 if (uart_handle_sysrq_char(&up->port, ch)) 560 return; 561 562 uart_insert_char(&up->port, lsr, UART_LSR_OE, ch, flag); 563 } 564 565 /** 566 * serial_omap_irq() - This handles the interrupt from one port 567 * @irq: uart port irq number 568 * @dev_id: uart port info 569 */ 570 static irqreturn_t serial_omap_irq(int irq, void *dev_id) 571 { 572 struct uart_omap_port *up = dev_id; 573 unsigned int iir, lsr; 574 unsigned int type; 575 irqreturn_t ret = IRQ_NONE; 576 int max_count = 256; 577 578 spin_lock(&up->port.lock); 579 pm_runtime_get_sync(up->dev); 580 581 do { 582 iir = serial_in(up, UART_IIR); 583 if (iir & UART_IIR_NO_INT) 584 break; 585 586 ret = IRQ_HANDLED; 587 lsr = serial_in(up, UART_LSR); 588 589 /* extract IRQ type from IIR register */ 590 type = iir & 0x3e; 591 592 switch (type) { 593 case UART_IIR_MSI: 594 check_modem_status(up); 595 break; 596 case UART_IIR_THRI: 597 transmit_chars(up, lsr); 598 break; 599 case UART_IIR_RX_TIMEOUT: 600 case UART_IIR_RDI: 601 serial_omap_rdi(up, lsr); 602 break; 603 case UART_IIR_RLSI: 604 serial_omap_rlsi(up, lsr); 605 break; 606 case UART_IIR_CTS_RTS_DSR: 607 /* simply try again */ 608 break; 609 case UART_IIR_XOFF: 610 default: 611 break; 612 } 613 } while (max_count--); 614 615 spin_unlock(&up->port.lock); 616 617 tty_flip_buffer_push(&up->port.state->port); 618 619 pm_runtime_mark_last_busy(up->dev); 620 pm_runtime_put_autosuspend(up->dev); 621 up->port_activity = jiffies; 622 623 return ret; 624 } 625 626 static unsigned int serial_omap_tx_empty(struct uart_port *port) 627 { 628 struct uart_omap_port *up = to_uart_omap_port(port); 629 unsigned long flags; 630 unsigned int ret = 0; 631 632 pm_runtime_get_sync(up->dev); 633 dev_dbg(up->port.dev, "serial_omap_tx_empty+%d\n", up->port.line); 634 spin_lock_irqsave(&up->port.lock, flags); 635 ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0; 636 spin_unlock_irqrestore(&up->port.lock, flags); 637 pm_runtime_mark_last_busy(up->dev); 638 pm_runtime_put_autosuspend(up->dev); 639 return ret; 640 } 641 642 static unsigned int serial_omap_get_mctrl(struct uart_port *port) 643 { 644 struct uart_omap_port *up = to_uart_omap_port(port); 645 unsigned int status; 646 unsigned int ret = 0; 647 648 pm_runtime_get_sync(up->dev); 649 status = check_modem_status(up); 650 pm_runtime_mark_last_busy(up->dev); 651 pm_runtime_put_autosuspend(up->dev); 652 653 dev_dbg(up->port.dev, "serial_omap_get_mctrl+%d\n", up->port.line); 654 655 if (status & UART_MSR_DCD) 656 ret |= TIOCM_CAR; 657 if (status & UART_MSR_RI) 658 ret |= TIOCM_RNG; 659 if (status & UART_MSR_DSR) 660 ret |= TIOCM_DSR; 661 if (status & UART_MSR_CTS) 662 ret |= TIOCM_CTS; 663 return ret; 664 } 665 666 static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl) 667 { 668 struct uart_omap_port *up = to_uart_omap_port(port); 669 unsigned char mcr = 0, old_mcr, lcr; 670 671 dev_dbg(up->port.dev, "serial_omap_set_mctrl+%d\n", up->port.line); 672 if (mctrl & TIOCM_RTS) 673 mcr |= UART_MCR_RTS; 674 if (mctrl & TIOCM_DTR) 675 mcr |= UART_MCR_DTR; 676 if (mctrl & TIOCM_OUT1) 677 mcr |= UART_MCR_OUT1; 678 if (mctrl & TIOCM_OUT2) 679 mcr |= UART_MCR_OUT2; 680 if (mctrl & TIOCM_LOOP) 681 mcr |= UART_MCR_LOOP; 682 683 pm_runtime_get_sync(up->dev); 684 old_mcr = serial_in(up, UART_MCR); 685 old_mcr &= ~(UART_MCR_LOOP | UART_MCR_OUT2 | UART_MCR_OUT1 | 686 UART_MCR_DTR | UART_MCR_RTS); 687 up->mcr = old_mcr | mcr; 688 serial_out(up, UART_MCR, up->mcr); 689 690 /* Turn off autoRTS if RTS is lowered; restore autoRTS if RTS raised */ 691 lcr = serial_in(up, UART_LCR); 692 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 693 if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS)) 694 up->efr |= UART_EFR_RTS; 695 else 696 up->efr &= ~UART_EFR_RTS; 697 serial_out(up, UART_EFR, up->efr); 698 serial_out(up, UART_LCR, lcr); 699 700 pm_runtime_mark_last_busy(up->dev); 701 pm_runtime_put_autosuspend(up->dev); 702 } 703 704 static void serial_omap_break_ctl(struct uart_port *port, int break_state) 705 { 706 struct uart_omap_port *up = to_uart_omap_port(port); 707 unsigned long flags; 708 709 dev_dbg(up->port.dev, "serial_omap_break_ctl+%d\n", up->port.line); 710 pm_runtime_get_sync(up->dev); 711 spin_lock_irqsave(&up->port.lock, flags); 712 if (break_state == -1) 713 up->lcr |= UART_LCR_SBC; 714 else 715 up->lcr &= ~UART_LCR_SBC; 716 serial_out(up, UART_LCR, up->lcr); 717 spin_unlock_irqrestore(&up->port.lock, flags); 718 pm_runtime_mark_last_busy(up->dev); 719 pm_runtime_put_autosuspend(up->dev); 720 } 721 722 static int serial_omap_startup(struct uart_port *port) 723 { 724 struct uart_omap_port *up = to_uart_omap_port(port); 725 unsigned long flags; 726 int retval; 727 728 /* 729 * Allocate the IRQ 730 */ 731 retval = request_irq(up->port.irq, serial_omap_irq, up->port.irqflags, 732 up->name, up); 733 if (retval) 734 return retval; 735 736 /* Optional wake-up IRQ */ 737 if (up->wakeirq) { 738 retval = dev_pm_set_dedicated_wake_irq(up->dev, up->wakeirq); 739 if (retval) { 740 free_irq(up->port.irq, up); 741 return retval; 742 } 743 } 744 745 dev_dbg(up->port.dev, "serial_omap_startup+%d\n", up->port.line); 746 747 pm_runtime_get_sync(up->dev); 748 /* 749 * Clear the FIFO buffers and disable them. 750 * (they will be reenabled in set_termios()) 751 */ 752 serial_omap_clear_fifos(up); 753 754 /* 755 * Clear the interrupt registers. 756 */ 757 (void) serial_in(up, UART_LSR); 758 if (serial_in(up, UART_LSR) & UART_LSR_DR) 759 (void) serial_in(up, UART_RX); 760 (void) serial_in(up, UART_IIR); 761 (void) serial_in(up, UART_MSR); 762 763 /* 764 * Now, initialize the UART 765 */ 766 serial_out(up, UART_LCR, UART_LCR_WLEN8); 767 spin_lock_irqsave(&up->port.lock, flags); 768 /* 769 * Most PC uarts need OUT2 raised to enable interrupts. 770 */ 771 up->port.mctrl |= TIOCM_OUT2; 772 serial_omap_set_mctrl(&up->port, up->port.mctrl); 773 spin_unlock_irqrestore(&up->port.lock, flags); 774 775 up->msr_saved_flags = 0; 776 /* 777 * Finally, enable interrupts. Note: Modem status interrupts 778 * are set via set_termios(), which will be occurring imminently 779 * anyway, so we don't enable them here. 780 */ 781 up->ier = UART_IER_RLSI | UART_IER_RDI; 782 serial_out(up, UART_IER, up->ier); 783 784 /* Enable module level wake up */ 785 up->wer = OMAP_UART_WER_MOD_WKUP; 786 if (up->features & OMAP_UART_WER_HAS_TX_WAKEUP) 787 up->wer |= OMAP_UART_TX_WAKEUP_EN; 788 789 serial_out(up, UART_OMAP_WER, up->wer); 790 791 pm_runtime_mark_last_busy(up->dev); 792 pm_runtime_put_autosuspend(up->dev); 793 up->port_activity = jiffies; 794 return 0; 795 } 796 797 static void serial_omap_shutdown(struct uart_port *port) 798 { 799 struct uart_omap_port *up = to_uart_omap_port(port); 800 unsigned long flags; 801 802 dev_dbg(up->port.dev, "serial_omap_shutdown+%d\n", up->port.line); 803 804 pm_runtime_get_sync(up->dev); 805 /* 806 * Disable interrupts from this port 807 */ 808 up->ier = 0; 809 serial_out(up, UART_IER, 0); 810 811 spin_lock_irqsave(&up->port.lock, flags); 812 up->port.mctrl &= ~TIOCM_OUT2; 813 serial_omap_set_mctrl(&up->port, up->port.mctrl); 814 spin_unlock_irqrestore(&up->port.lock, flags); 815 816 /* 817 * Disable break condition and FIFOs 818 */ 819 serial_out(up, UART_LCR, serial_in(up, UART_LCR) & ~UART_LCR_SBC); 820 serial_omap_clear_fifos(up); 821 822 /* 823 * Read data port to reset things, and then free the irq 824 */ 825 if (serial_in(up, UART_LSR) & UART_LSR_DR) 826 (void) serial_in(up, UART_RX); 827 828 pm_runtime_mark_last_busy(up->dev); 829 pm_runtime_put_autosuspend(up->dev); 830 free_irq(up->port.irq, up); 831 dev_pm_clear_wake_irq(up->dev); 832 } 833 834 static void serial_omap_uart_qos_work(struct work_struct *work) 835 { 836 struct uart_omap_port *up = container_of(work, struct uart_omap_port, 837 qos_work); 838 839 cpu_latency_qos_update_request(&up->pm_qos_request, up->latency); 840 } 841 842 static void 843 serial_omap_set_termios(struct uart_port *port, struct ktermios *termios, 844 struct ktermios *old) 845 { 846 struct uart_omap_port *up = to_uart_omap_port(port); 847 unsigned char cval = 0; 848 unsigned long flags; 849 unsigned int baud, quot; 850 851 switch (termios->c_cflag & CSIZE) { 852 case CS5: 853 cval = UART_LCR_WLEN5; 854 break; 855 case CS6: 856 cval = UART_LCR_WLEN6; 857 break; 858 case CS7: 859 cval = UART_LCR_WLEN7; 860 break; 861 default: 862 case CS8: 863 cval = UART_LCR_WLEN8; 864 break; 865 } 866 867 if (termios->c_cflag & CSTOPB) 868 cval |= UART_LCR_STOP; 869 if (termios->c_cflag & PARENB) 870 cval |= UART_LCR_PARITY; 871 if (!(termios->c_cflag & PARODD)) 872 cval |= UART_LCR_EPAR; 873 if (termios->c_cflag & CMSPAR) 874 cval |= UART_LCR_SPAR; 875 876 /* 877 * Ask the core to calculate the divisor for us. 878 */ 879 880 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/13); 881 quot = serial_omap_get_divisor(port, baud); 882 883 /* calculate wakeup latency constraint */ 884 up->calc_latency = (USEC_PER_SEC * up->port.fifosize) / (baud / 8); 885 up->latency = up->calc_latency; 886 schedule_work(&up->qos_work); 887 888 up->dll = quot & 0xff; 889 up->dlh = quot >> 8; 890 up->mdr1 = UART_OMAP_MDR1_DISABLE; 891 892 up->fcr = UART_FCR_R_TRIG_01 | UART_FCR_T_TRIG_01 | 893 UART_FCR_ENABLE_FIFO; 894 895 /* 896 * Ok, we're now changing the port state. Do it with 897 * interrupts disabled. 898 */ 899 pm_runtime_get_sync(up->dev); 900 spin_lock_irqsave(&up->port.lock, flags); 901 902 /* 903 * Update the per-port timeout. 904 */ 905 uart_update_timeout(port, termios->c_cflag, baud); 906 907 up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; 908 if (termios->c_iflag & INPCK) 909 up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE; 910 if (termios->c_iflag & (BRKINT | PARMRK)) 911 up->port.read_status_mask |= UART_LSR_BI; 912 913 /* 914 * Characters to ignore 915 */ 916 up->port.ignore_status_mask = 0; 917 if (termios->c_iflag & IGNPAR) 918 up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; 919 if (termios->c_iflag & IGNBRK) { 920 up->port.ignore_status_mask |= UART_LSR_BI; 921 /* 922 * If we're ignoring parity and break indicators, 923 * ignore overruns too (for real raw support). 924 */ 925 if (termios->c_iflag & IGNPAR) 926 up->port.ignore_status_mask |= UART_LSR_OE; 927 } 928 929 /* 930 * ignore all characters if CREAD is not set 931 */ 932 if ((termios->c_cflag & CREAD) == 0) 933 up->port.ignore_status_mask |= UART_LSR_DR; 934 935 /* 936 * Modem status interrupts 937 */ 938 up->ier &= ~UART_IER_MSI; 939 if (UART_ENABLE_MS(&up->port, termios->c_cflag)) 940 up->ier |= UART_IER_MSI; 941 serial_out(up, UART_IER, up->ier); 942 serial_out(up, UART_LCR, cval); /* reset DLAB */ 943 up->lcr = cval; 944 up->scr = 0; 945 946 /* FIFOs and DMA Settings */ 947 948 /* FCR can be changed only when the 949 * baud clock is not running 950 * DLL_REG and DLH_REG set to 0. 951 */ 952 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); 953 serial_out(up, UART_DLL, 0); 954 serial_out(up, UART_DLM, 0); 955 serial_out(up, UART_LCR, 0); 956 957 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 958 959 up->efr = serial_in(up, UART_EFR) & ~UART_EFR_ECB; 960 up->efr &= ~UART_EFR_SCD; 961 serial_out(up, UART_EFR, up->efr | UART_EFR_ECB); 962 963 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); 964 up->mcr = serial_in(up, UART_MCR) & ~UART_MCR_TCRTLR; 965 serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR); 966 /* FIFO ENABLE, DMA MODE */ 967 968 up->scr |= OMAP_UART_SCR_RX_TRIG_GRANU1_MASK; 969 /* 970 * NOTE: Setting OMAP_UART_SCR_RX_TRIG_GRANU1_MASK 971 * sets Enables the granularity of 1 for TRIGGER RX 972 * level. Along with setting RX FIFO trigger level 973 * to 1 (as noted below, 16 characters) and TLR[3:0] 974 * to zero this will result RX FIFO threshold level 975 * to 1 character, instead of 16 as noted in comment 976 * below. 977 */ 978 979 /* Set receive FIFO threshold to 16 characters and 980 * transmit FIFO threshold to 32 spaces 981 */ 982 up->fcr &= ~OMAP_UART_FCR_RX_FIFO_TRIG_MASK; 983 up->fcr &= ~OMAP_UART_FCR_TX_FIFO_TRIG_MASK; 984 up->fcr |= UART_FCR6_R_TRIGGER_16 | UART_FCR6_T_TRIGGER_24 | 985 UART_FCR_ENABLE_FIFO; 986 987 serial_out(up, UART_FCR, up->fcr); 988 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 989 990 serial_out(up, UART_OMAP_SCR, up->scr); 991 992 /* Reset UART_MCR_TCRTLR: this must be done with the EFR_ECB bit set */ 993 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); 994 serial_out(up, UART_MCR, up->mcr); 995 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 996 serial_out(up, UART_EFR, up->efr); 997 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); 998 999 /* Protocol, Baud Rate, and Interrupt Settings */ 1000 1001 if (up->errata & UART_ERRATA_i202_MDR1_ACCESS) 1002 serial_omap_mdr1_errataset(up, up->mdr1); 1003 else 1004 serial_out(up, UART_OMAP_MDR1, up->mdr1); 1005 1006 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 1007 serial_out(up, UART_EFR, up->efr | UART_EFR_ECB); 1008 1009 serial_out(up, UART_LCR, 0); 1010 serial_out(up, UART_IER, 0); 1011 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 1012 1013 serial_out(up, UART_DLL, up->dll); /* LS of divisor */ 1014 serial_out(up, UART_DLM, up->dlh); /* MS of divisor */ 1015 1016 serial_out(up, UART_LCR, 0); 1017 serial_out(up, UART_IER, up->ier); 1018 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 1019 1020 serial_out(up, UART_EFR, up->efr); 1021 serial_out(up, UART_LCR, cval); 1022 1023 if (!serial_omap_baud_is_mode16(port, baud)) 1024 up->mdr1 = UART_OMAP_MDR1_13X_MODE; 1025 else 1026 up->mdr1 = UART_OMAP_MDR1_16X_MODE; 1027 1028 if (up->errata & UART_ERRATA_i202_MDR1_ACCESS) 1029 serial_omap_mdr1_errataset(up, up->mdr1); 1030 else 1031 serial_out(up, UART_OMAP_MDR1, up->mdr1); 1032 1033 /* Configure flow control */ 1034 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 1035 1036 /* XON1/XOFF1 accessible mode B, TCRTLR=0, ECB=0 */ 1037 serial_out(up, UART_XON1, termios->c_cc[VSTART]); 1038 serial_out(up, UART_XOFF1, termios->c_cc[VSTOP]); 1039 1040 /* Enable access to TCR/TLR */ 1041 serial_out(up, UART_EFR, up->efr | UART_EFR_ECB); 1042 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); 1043 serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR); 1044 1045 serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG); 1046 1047 up->port.status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS | UPSTAT_AUTOXOFF); 1048 1049 if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW) { 1050 /* Enable AUTOCTS (autoRTS is enabled when RTS is raised) */ 1051 up->port.status |= UPSTAT_AUTOCTS | UPSTAT_AUTORTS; 1052 up->efr |= UART_EFR_CTS; 1053 } else { 1054 /* Disable AUTORTS and AUTOCTS */ 1055 up->efr &= ~(UART_EFR_CTS | UART_EFR_RTS); 1056 } 1057 1058 if (up->port.flags & UPF_SOFT_FLOW) { 1059 /* clear SW control mode bits */ 1060 up->efr &= OMAP_UART_SW_CLR; 1061 1062 /* 1063 * IXON Flag: 1064 * Enable XON/XOFF flow control on input. 1065 * Receiver compares XON1, XOFF1. 1066 */ 1067 if (termios->c_iflag & IXON) 1068 up->efr |= OMAP_UART_SW_RX; 1069 1070 /* 1071 * IXOFF Flag: 1072 * Enable XON/XOFF flow control on output. 1073 * Transmit XON1, XOFF1 1074 */ 1075 if (termios->c_iflag & IXOFF) { 1076 up->port.status |= UPSTAT_AUTOXOFF; 1077 up->efr |= OMAP_UART_SW_TX; 1078 } 1079 1080 /* 1081 * IXANY Flag: 1082 * Enable any character to restart output. 1083 * Operation resumes after receiving any 1084 * character after recognition of the XOFF character 1085 */ 1086 if (termios->c_iflag & IXANY) 1087 up->mcr |= UART_MCR_XONANY; 1088 else 1089 up->mcr &= ~UART_MCR_XONANY; 1090 } 1091 serial_out(up, UART_MCR, up->mcr); 1092 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 1093 serial_out(up, UART_EFR, up->efr); 1094 serial_out(up, UART_LCR, up->lcr); 1095 1096 serial_omap_set_mctrl(&up->port, up->port.mctrl); 1097 1098 spin_unlock_irqrestore(&up->port.lock, flags); 1099 pm_runtime_mark_last_busy(up->dev); 1100 pm_runtime_put_autosuspend(up->dev); 1101 dev_dbg(up->port.dev, "serial_omap_set_termios+%d\n", up->port.line); 1102 } 1103 1104 static void 1105 serial_omap_pm(struct uart_port *port, unsigned int state, 1106 unsigned int oldstate) 1107 { 1108 struct uart_omap_port *up = to_uart_omap_port(port); 1109 unsigned char efr; 1110 1111 dev_dbg(up->port.dev, "serial_omap_pm+%d\n", up->port.line); 1112 1113 pm_runtime_get_sync(up->dev); 1114 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 1115 efr = serial_in(up, UART_EFR); 1116 serial_out(up, UART_EFR, efr | UART_EFR_ECB); 1117 serial_out(up, UART_LCR, 0); 1118 1119 serial_out(up, UART_IER, (state != 0) ? UART_IERX_SLEEP : 0); 1120 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 1121 serial_out(up, UART_EFR, efr); 1122 serial_out(up, UART_LCR, 0); 1123 1124 pm_runtime_mark_last_busy(up->dev); 1125 pm_runtime_put_autosuspend(up->dev); 1126 } 1127 1128 static void serial_omap_release_port(struct uart_port *port) 1129 { 1130 dev_dbg(port->dev, "serial_omap_release_port+\n"); 1131 } 1132 1133 static int serial_omap_request_port(struct uart_port *port) 1134 { 1135 dev_dbg(port->dev, "serial_omap_request_port+\n"); 1136 return 0; 1137 } 1138 1139 static void serial_omap_config_port(struct uart_port *port, int flags) 1140 { 1141 struct uart_omap_port *up = to_uart_omap_port(port); 1142 1143 dev_dbg(up->port.dev, "serial_omap_config_port+%d\n", 1144 up->port.line); 1145 up->port.type = PORT_OMAP; 1146 up->port.flags |= UPF_SOFT_FLOW | UPF_HARD_FLOW; 1147 } 1148 1149 static int 1150 serial_omap_verify_port(struct uart_port *port, struct serial_struct *ser) 1151 { 1152 /* we don't want the core code to modify any port params */ 1153 dev_dbg(port->dev, "serial_omap_verify_port+\n"); 1154 return -EINVAL; 1155 } 1156 1157 static const char * 1158 serial_omap_type(struct uart_port *port) 1159 { 1160 struct uart_omap_port *up = to_uart_omap_port(port); 1161 1162 dev_dbg(up->port.dev, "serial_omap_type+%d\n", up->port.line); 1163 return up->name; 1164 } 1165 1166 #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) 1167 1168 static void __maybe_unused wait_for_xmitr(struct uart_omap_port *up) 1169 { 1170 unsigned int status, tmout = 10000; 1171 1172 /* Wait up to 10ms for the character(s) to be sent. */ 1173 do { 1174 status = serial_in(up, UART_LSR); 1175 1176 if (status & UART_LSR_BI) 1177 up->lsr_break_flag = UART_LSR_BI; 1178 1179 if (--tmout == 0) 1180 break; 1181 udelay(1); 1182 } while ((status & BOTH_EMPTY) != BOTH_EMPTY); 1183 1184 /* Wait up to 1s for flow control if necessary */ 1185 if (up->port.flags & UPF_CONS_FLOW) { 1186 tmout = 1000000; 1187 for (tmout = 1000000; tmout; tmout--) { 1188 unsigned int msr = serial_in(up, UART_MSR); 1189 1190 up->msr_saved_flags |= msr & MSR_SAVE_FLAGS; 1191 if (msr & UART_MSR_CTS) 1192 break; 1193 1194 udelay(1); 1195 } 1196 } 1197 } 1198 1199 #ifdef CONFIG_CONSOLE_POLL 1200 1201 static void serial_omap_poll_put_char(struct uart_port *port, unsigned char ch) 1202 { 1203 struct uart_omap_port *up = to_uart_omap_port(port); 1204 1205 pm_runtime_get_sync(up->dev); 1206 wait_for_xmitr(up); 1207 serial_out(up, UART_TX, ch); 1208 pm_runtime_mark_last_busy(up->dev); 1209 pm_runtime_put_autosuspend(up->dev); 1210 } 1211 1212 static int serial_omap_poll_get_char(struct uart_port *port) 1213 { 1214 struct uart_omap_port *up = to_uart_omap_port(port); 1215 unsigned int status; 1216 1217 pm_runtime_get_sync(up->dev); 1218 status = serial_in(up, UART_LSR); 1219 if (!(status & UART_LSR_DR)) { 1220 status = NO_POLL_CHAR; 1221 goto out; 1222 } 1223 1224 status = serial_in(up, UART_RX); 1225 1226 out: 1227 pm_runtime_mark_last_busy(up->dev); 1228 pm_runtime_put_autosuspend(up->dev); 1229 1230 return status; 1231 } 1232 1233 #endif /* CONFIG_CONSOLE_POLL */ 1234 1235 #ifdef CONFIG_SERIAL_OMAP_CONSOLE 1236 1237 #ifdef CONFIG_SERIAL_EARLYCON 1238 static unsigned int omap_serial_early_in(struct uart_port *port, int offset) 1239 { 1240 offset <<= port->regshift; 1241 return readw(port->membase + offset); 1242 } 1243 1244 static void omap_serial_early_out(struct uart_port *port, int offset, 1245 int value) 1246 { 1247 offset <<= port->regshift; 1248 writew(value, port->membase + offset); 1249 } 1250 1251 static void omap_serial_early_putc(struct uart_port *port, int c) 1252 { 1253 unsigned int status; 1254 1255 for (;;) { 1256 status = omap_serial_early_in(port, UART_LSR); 1257 if ((status & BOTH_EMPTY) == BOTH_EMPTY) 1258 break; 1259 cpu_relax(); 1260 } 1261 omap_serial_early_out(port, UART_TX, c); 1262 } 1263 1264 static void early_omap_serial_write(struct console *console, const char *s, 1265 unsigned int count) 1266 { 1267 struct earlycon_device *device = console->data; 1268 struct uart_port *port = &device->port; 1269 1270 uart_console_write(port, s, count, omap_serial_early_putc); 1271 } 1272 1273 static int __init early_omap_serial_setup(struct earlycon_device *device, 1274 const char *options) 1275 { 1276 struct uart_port *port = &device->port; 1277 1278 if (!(device->port.membase || device->port.iobase)) 1279 return -ENODEV; 1280 1281 port->regshift = 2; 1282 device->con->write = early_omap_serial_write; 1283 return 0; 1284 } 1285 1286 OF_EARLYCON_DECLARE(omapserial, "ti,omap2-uart", early_omap_serial_setup); 1287 OF_EARLYCON_DECLARE(omapserial, "ti,omap3-uart", early_omap_serial_setup); 1288 OF_EARLYCON_DECLARE(omapserial, "ti,omap4-uart", early_omap_serial_setup); 1289 #endif /* CONFIG_SERIAL_EARLYCON */ 1290 1291 static struct uart_omap_port *serial_omap_console_ports[OMAP_MAX_HSUART_PORTS]; 1292 1293 static struct uart_driver serial_omap_reg; 1294 1295 static void serial_omap_console_putchar(struct uart_port *port, int ch) 1296 { 1297 struct uart_omap_port *up = to_uart_omap_port(port); 1298 1299 wait_for_xmitr(up); 1300 serial_out(up, UART_TX, ch); 1301 } 1302 1303 static void 1304 serial_omap_console_write(struct console *co, const char *s, 1305 unsigned int count) 1306 { 1307 struct uart_omap_port *up = serial_omap_console_ports[co->index]; 1308 unsigned long flags; 1309 unsigned int ier; 1310 int locked = 1; 1311 1312 pm_runtime_get_sync(up->dev); 1313 1314 local_irq_save(flags); 1315 if (up->port.sysrq) 1316 locked = 0; 1317 else if (oops_in_progress) 1318 locked = spin_trylock(&up->port.lock); 1319 else 1320 spin_lock(&up->port.lock); 1321 1322 /* 1323 * First save the IER then disable the interrupts 1324 */ 1325 ier = serial_in(up, UART_IER); 1326 serial_out(up, UART_IER, 0); 1327 1328 uart_console_write(&up->port, s, count, serial_omap_console_putchar); 1329 1330 /* 1331 * Finally, wait for transmitter to become empty 1332 * and restore the IER 1333 */ 1334 wait_for_xmitr(up); 1335 serial_out(up, UART_IER, ier); 1336 /* 1337 * The receive handling will happen properly because the 1338 * receive ready bit will still be set; it is not cleared 1339 * on read. However, modem control will not, we must 1340 * call it if we have saved something in the saved flags 1341 * while processing with interrupts off. 1342 */ 1343 if (up->msr_saved_flags) 1344 check_modem_status(up); 1345 1346 pm_runtime_mark_last_busy(up->dev); 1347 pm_runtime_put_autosuspend(up->dev); 1348 if (locked) 1349 spin_unlock(&up->port.lock); 1350 local_irq_restore(flags); 1351 } 1352 1353 static int __init 1354 serial_omap_console_setup(struct console *co, char *options) 1355 { 1356 struct uart_omap_port *up; 1357 int baud = 115200; 1358 int bits = 8; 1359 int parity = 'n'; 1360 int flow = 'n'; 1361 1362 if (serial_omap_console_ports[co->index] == NULL) 1363 return -ENODEV; 1364 up = serial_omap_console_ports[co->index]; 1365 1366 if (options) 1367 uart_parse_options(options, &baud, &parity, &bits, &flow); 1368 1369 return uart_set_options(&up->port, co, baud, parity, bits, flow); 1370 } 1371 1372 static struct console serial_omap_console = { 1373 .name = OMAP_SERIAL_NAME, 1374 .write = serial_omap_console_write, 1375 .device = uart_console_device, 1376 .setup = serial_omap_console_setup, 1377 .flags = CON_PRINTBUFFER, 1378 .index = -1, 1379 .data = &serial_omap_reg, 1380 }; 1381 1382 static void serial_omap_add_console_port(struct uart_omap_port *up) 1383 { 1384 serial_omap_console_ports[up->port.line] = up; 1385 } 1386 1387 #define OMAP_CONSOLE (&serial_omap_console) 1388 1389 #else 1390 1391 #define OMAP_CONSOLE NULL 1392 1393 static inline void serial_omap_add_console_port(struct uart_omap_port *up) 1394 {} 1395 1396 #endif 1397 1398 /* Enable or disable the rs485 support */ 1399 static int 1400 serial_omap_config_rs485(struct uart_port *port, struct serial_rs485 *rs485) 1401 { 1402 struct uart_omap_port *up = to_uart_omap_port(port); 1403 unsigned int mode; 1404 int val; 1405 1406 pm_runtime_get_sync(up->dev); 1407 1408 /* Disable interrupts from this port */ 1409 mode = up->ier; 1410 up->ier = 0; 1411 serial_out(up, UART_IER, 0); 1412 1413 /* Clamp the delays to [0, 100ms] */ 1414 rs485->delay_rts_before_send = min(rs485->delay_rts_before_send, 100U); 1415 rs485->delay_rts_after_send = min(rs485->delay_rts_after_send, 100U); 1416 1417 /* store new config */ 1418 port->rs485 = *rs485; 1419 1420 if (up->rts_gpiod) { 1421 /* enable / disable rts */ 1422 val = (port->rs485.flags & SER_RS485_ENABLED) ? 1423 SER_RS485_RTS_AFTER_SEND : SER_RS485_RTS_ON_SEND; 1424 val = (port->rs485.flags & val) ? 1 : 0; 1425 gpiod_set_value(up->rts_gpiod, val); 1426 } 1427 1428 /* Enable interrupts */ 1429 up->ier = mode; 1430 serial_out(up, UART_IER, up->ier); 1431 1432 /* If RS-485 is disabled, make sure the THR interrupt is fired when 1433 * TX FIFO is below the trigger level. 1434 */ 1435 if (!(port->rs485.flags & SER_RS485_ENABLED) && 1436 (up->scr & OMAP_UART_SCR_TX_EMPTY)) { 1437 up->scr &= ~OMAP_UART_SCR_TX_EMPTY; 1438 serial_out(up, UART_OMAP_SCR, up->scr); 1439 } 1440 1441 pm_runtime_mark_last_busy(up->dev); 1442 pm_runtime_put_autosuspend(up->dev); 1443 1444 return 0; 1445 } 1446 1447 static const struct uart_ops serial_omap_pops = { 1448 .tx_empty = serial_omap_tx_empty, 1449 .set_mctrl = serial_omap_set_mctrl, 1450 .get_mctrl = serial_omap_get_mctrl, 1451 .stop_tx = serial_omap_stop_tx, 1452 .start_tx = serial_omap_start_tx, 1453 .throttle = serial_omap_throttle, 1454 .unthrottle = serial_omap_unthrottle, 1455 .stop_rx = serial_omap_stop_rx, 1456 .enable_ms = serial_omap_enable_ms, 1457 .break_ctl = serial_omap_break_ctl, 1458 .startup = serial_omap_startup, 1459 .shutdown = serial_omap_shutdown, 1460 .set_termios = serial_omap_set_termios, 1461 .pm = serial_omap_pm, 1462 .type = serial_omap_type, 1463 .release_port = serial_omap_release_port, 1464 .request_port = serial_omap_request_port, 1465 .config_port = serial_omap_config_port, 1466 .verify_port = serial_omap_verify_port, 1467 #ifdef CONFIG_CONSOLE_POLL 1468 .poll_put_char = serial_omap_poll_put_char, 1469 .poll_get_char = serial_omap_poll_get_char, 1470 #endif 1471 }; 1472 1473 static struct uart_driver serial_omap_reg = { 1474 .owner = THIS_MODULE, 1475 .driver_name = "OMAP-SERIAL", 1476 .dev_name = OMAP_SERIAL_NAME, 1477 .nr = OMAP_MAX_HSUART_PORTS, 1478 .cons = OMAP_CONSOLE, 1479 }; 1480 1481 #ifdef CONFIG_PM_SLEEP 1482 static int serial_omap_prepare(struct device *dev) 1483 { 1484 struct uart_omap_port *up = dev_get_drvdata(dev); 1485 1486 up->is_suspending = true; 1487 1488 return 0; 1489 } 1490 1491 static void serial_omap_complete(struct device *dev) 1492 { 1493 struct uart_omap_port *up = dev_get_drvdata(dev); 1494 1495 up->is_suspending = false; 1496 } 1497 1498 static int serial_omap_suspend(struct device *dev) 1499 { 1500 struct uart_omap_port *up = dev_get_drvdata(dev); 1501 1502 uart_suspend_port(&serial_omap_reg, &up->port); 1503 flush_work(&up->qos_work); 1504 1505 if (device_may_wakeup(dev)) 1506 serial_omap_enable_wakeup(up, true); 1507 else 1508 serial_omap_enable_wakeup(up, false); 1509 1510 return 0; 1511 } 1512 1513 static int serial_omap_resume(struct device *dev) 1514 { 1515 struct uart_omap_port *up = dev_get_drvdata(dev); 1516 1517 if (device_may_wakeup(dev)) 1518 serial_omap_enable_wakeup(up, false); 1519 1520 uart_resume_port(&serial_omap_reg, &up->port); 1521 1522 return 0; 1523 } 1524 #else 1525 #define serial_omap_prepare NULL 1526 #define serial_omap_complete NULL 1527 #endif /* CONFIG_PM_SLEEP */ 1528 1529 static void omap_serial_fill_features_erratas(struct uart_omap_port *up) 1530 { 1531 u32 mvr, scheme; 1532 u16 revision, major, minor; 1533 1534 mvr = readl(up->port.membase + (UART_OMAP_MVER << up->port.regshift)); 1535 1536 /* Check revision register scheme */ 1537 scheme = mvr >> OMAP_UART_MVR_SCHEME_SHIFT; 1538 1539 switch (scheme) { 1540 case 0: /* Legacy Scheme: OMAP2/3 */ 1541 /* MINOR_REV[0:4], MAJOR_REV[4:7] */ 1542 major = (mvr & OMAP_UART_LEGACY_MVR_MAJ_MASK) >> 1543 OMAP_UART_LEGACY_MVR_MAJ_SHIFT; 1544 minor = (mvr & OMAP_UART_LEGACY_MVR_MIN_MASK); 1545 break; 1546 case 1: 1547 /* New Scheme: OMAP4+ */ 1548 /* MINOR_REV[0:5], MAJOR_REV[8:10] */ 1549 major = (mvr & OMAP_UART_MVR_MAJ_MASK) >> 1550 OMAP_UART_MVR_MAJ_SHIFT; 1551 minor = (mvr & OMAP_UART_MVR_MIN_MASK); 1552 break; 1553 default: 1554 dev_warn(up->dev, 1555 "Unknown %s revision, defaulting to highest\n", 1556 up->name); 1557 /* highest possible revision */ 1558 major = 0xff; 1559 minor = 0xff; 1560 } 1561 1562 /* normalize revision for the driver */ 1563 revision = UART_BUILD_REVISION(major, minor); 1564 1565 switch (revision) { 1566 case OMAP_UART_REV_46: 1567 up->errata |= (UART_ERRATA_i202_MDR1_ACCESS | 1568 UART_ERRATA_i291_DMA_FORCEIDLE); 1569 break; 1570 case OMAP_UART_REV_52: 1571 up->errata |= (UART_ERRATA_i202_MDR1_ACCESS | 1572 UART_ERRATA_i291_DMA_FORCEIDLE); 1573 up->features |= OMAP_UART_WER_HAS_TX_WAKEUP; 1574 break; 1575 case OMAP_UART_REV_63: 1576 up->errata |= UART_ERRATA_i202_MDR1_ACCESS; 1577 up->features |= OMAP_UART_WER_HAS_TX_WAKEUP; 1578 break; 1579 default: 1580 break; 1581 } 1582 } 1583 1584 static struct omap_uart_port_info *of_get_uart_port_info(struct device *dev) 1585 { 1586 struct omap_uart_port_info *omap_up_info; 1587 1588 omap_up_info = devm_kzalloc(dev, sizeof(*omap_up_info), GFP_KERNEL); 1589 if (!omap_up_info) 1590 return NULL; /* out of memory */ 1591 1592 of_property_read_u32(dev->of_node, "clock-frequency", 1593 &omap_up_info->uartclk); 1594 1595 omap_up_info->flags = UPF_BOOT_AUTOCONF; 1596 1597 return omap_up_info; 1598 } 1599 1600 static int serial_omap_probe_rs485(struct uart_omap_port *up, 1601 struct device *dev) 1602 { 1603 struct serial_rs485 *rs485conf = &up->port.rs485; 1604 struct device_node *np = dev->of_node; 1605 enum gpiod_flags gflags; 1606 int ret; 1607 1608 rs485conf->flags = 0; 1609 up->rts_gpiod = NULL; 1610 1611 if (!np) 1612 return 0; 1613 1614 ret = uart_get_rs485_mode(&up->port); 1615 if (ret) 1616 return ret; 1617 1618 if (of_property_read_bool(np, "rs485-rts-active-high")) { 1619 rs485conf->flags |= SER_RS485_RTS_ON_SEND; 1620 rs485conf->flags &= ~SER_RS485_RTS_AFTER_SEND; 1621 } else { 1622 rs485conf->flags &= ~SER_RS485_RTS_ON_SEND; 1623 rs485conf->flags |= SER_RS485_RTS_AFTER_SEND; 1624 } 1625 1626 /* check for tx enable gpio */ 1627 gflags = rs485conf->flags & SER_RS485_RTS_AFTER_SEND ? 1628 GPIOD_OUT_HIGH : GPIOD_OUT_LOW; 1629 up->rts_gpiod = devm_gpiod_get_optional(dev, "rts", gflags); 1630 if (IS_ERR(up->rts_gpiod)) { 1631 ret = PTR_ERR(up->rts_gpiod); 1632 if (ret == -EPROBE_DEFER) 1633 return ret; 1634 /* 1635 * FIXME: the code historically ignored any other error than 1636 * -EPROBE_DEFER and just went on without GPIO. 1637 */ 1638 up->rts_gpiod = NULL; 1639 } else { 1640 gpiod_set_consumer_name(up->rts_gpiod, "omap-serial"); 1641 } 1642 1643 return 0; 1644 } 1645 1646 static int serial_omap_probe(struct platform_device *pdev) 1647 { 1648 struct omap_uart_port_info *omap_up_info = dev_get_platdata(&pdev->dev); 1649 struct uart_omap_port *up; 1650 struct resource *mem; 1651 void __iomem *base; 1652 int uartirq = 0; 1653 int wakeirq = 0; 1654 int ret; 1655 1656 /* The optional wakeirq may be specified in the board dts file */ 1657 if (pdev->dev.of_node) { 1658 uartirq = irq_of_parse_and_map(pdev->dev.of_node, 0); 1659 if (!uartirq) 1660 return -EPROBE_DEFER; 1661 wakeirq = irq_of_parse_and_map(pdev->dev.of_node, 1); 1662 omap_up_info = of_get_uart_port_info(&pdev->dev); 1663 pdev->dev.platform_data = omap_up_info; 1664 } else { 1665 uartirq = platform_get_irq(pdev, 0); 1666 if (uartirq < 0) 1667 return -EPROBE_DEFER; 1668 } 1669 1670 up = devm_kzalloc(&pdev->dev, sizeof(*up), GFP_KERNEL); 1671 if (!up) 1672 return -ENOMEM; 1673 1674 mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1675 base = devm_ioremap_resource(&pdev->dev, mem); 1676 if (IS_ERR(base)) 1677 return PTR_ERR(base); 1678 1679 up->dev = &pdev->dev; 1680 up->port.dev = &pdev->dev; 1681 up->port.type = PORT_OMAP; 1682 up->port.iotype = UPIO_MEM; 1683 up->port.irq = uartirq; 1684 up->port.regshift = 2; 1685 up->port.fifosize = 64; 1686 up->port.ops = &serial_omap_pops; 1687 up->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_OMAP_CONSOLE); 1688 1689 if (pdev->dev.of_node) 1690 ret = of_alias_get_id(pdev->dev.of_node, "serial"); 1691 else 1692 ret = pdev->id; 1693 1694 if (ret < 0) { 1695 dev_err(&pdev->dev, "failed to get alias/pdev id, errno %d\n", 1696 ret); 1697 goto err_port_line; 1698 } 1699 up->port.line = ret; 1700 1701 if (up->port.line >= OMAP_MAX_HSUART_PORTS) { 1702 dev_err(&pdev->dev, "uart ID %d > MAX %d.\n", up->port.line, 1703 OMAP_MAX_HSUART_PORTS); 1704 ret = -ENXIO; 1705 goto err_port_line; 1706 } 1707 1708 up->wakeirq = wakeirq; 1709 if (!up->wakeirq) 1710 dev_info(up->port.dev, "no wakeirq for uart%d\n", 1711 up->port.line); 1712 1713 ret = serial_omap_probe_rs485(up, &pdev->dev); 1714 if (ret < 0) 1715 goto err_rs485; 1716 1717 sprintf(up->name, "OMAP UART%d", up->port.line); 1718 up->port.mapbase = mem->start; 1719 up->port.membase = base; 1720 up->port.flags = omap_up_info->flags; 1721 up->port.uartclk = omap_up_info->uartclk; 1722 up->port.rs485_config = serial_omap_config_rs485; 1723 if (!up->port.uartclk) { 1724 up->port.uartclk = DEFAULT_CLK_SPEED; 1725 dev_warn(&pdev->dev, 1726 "No clock speed specified: using default: %d\n", 1727 DEFAULT_CLK_SPEED); 1728 } 1729 1730 up->latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE; 1731 up->calc_latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE; 1732 cpu_latency_qos_add_request(&up->pm_qos_request, up->latency); 1733 INIT_WORK(&up->qos_work, serial_omap_uart_qos_work); 1734 1735 platform_set_drvdata(pdev, up); 1736 if (omap_up_info->autosuspend_timeout == 0) 1737 omap_up_info->autosuspend_timeout = -1; 1738 1739 device_init_wakeup(up->dev, true); 1740 pm_runtime_use_autosuspend(&pdev->dev); 1741 pm_runtime_set_autosuspend_delay(&pdev->dev, 1742 omap_up_info->autosuspend_timeout); 1743 1744 pm_runtime_irq_safe(&pdev->dev); 1745 pm_runtime_enable(&pdev->dev); 1746 1747 pm_runtime_get_sync(&pdev->dev); 1748 1749 omap_serial_fill_features_erratas(up); 1750 1751 ui[up->port.line] = up; 1752 serial_omap_add_console_port(up); 1753 1754 ret = uart_add_one_port(&serial_omap_reg, &up->port); 1755 if (ret != 0) 1756 goto err_add_port; 1757 1758 pm_runtime_mark_last_busy(up->dev); 1759 pm_runtime_put_autosuspend(up->dev); 1760 return 0; 1761 1762 err_add_port: 1763 pm_runtime_dont_use_autosuspend(&pdev->dev); 1764 pm_runtime_put_sync(&pdev->dev); 1765 pm_runtime_disable(&pdev->dev); 1766 cpu_latency_qos_remove_request(&up->pm_qos_request); 1767 device_init_wakeup(up->dev, false); 1768 err_rs485: 1769 err_port_line: 1770 return ret; 1771 } 1772 1773 static int serial_omap_remove(struct platform_device *dev) 1774 { 1775 struct uart_omap_port *up = platform_get_drvdata(dev); 1776 1777 pm_runtime_get_sync(up->dev); 1778 1779 uart_remove_one_port(&serial_omap_reg, &up->port); 1780 1781 pm_runtime_dont_use_autosuspend(up->dev); 1782 pm_runtime_put_sync(up->dev); 1783 pm_runtime_disable(up->dev); 1784 cpu_latency_qos_remove_request(&up->pm_qos_request); 1785 device_init_wakeup(&dev->dev, false); 1786 1787 return 0; 1788 } 1789 1790 /* 1791 * Work Around for Errata i202 (2430, 3430, 3630, 4430 and 4460) 1792 * The access to uart register after MDR1 Access 1793 * causes UART to corrupt data. 1794 * 1795 * Need a delay = 1796 * 5 L4 clock cycles + 5 UART functional clock cycle (@48MHz = ~0.2uS) 1797 * give 10 times as much 1798 */ 1799 static void serial_omap_mdr1_errataset(struct uart_omap_port *up, u8 mdr1) 1800 { 1801 u8 timeout = 255; 1802 1803 serial_out(up, UART_OMAP_MDR1, mdr1); 1804 udelay(2); 1805 serial_out(up, UART_FCR, up->fcr | UART_FCR_CLEAR_XMIT | 1806 UART_FCR_CLEAR_RCVR); 1807 /* 1808 * Wait for FIFO to empty: when empty, RX_FIFO_E bit is 0 and 1809 * TX_FIFO_E bit is 1. 1810 */ 1811 while (UART_LSR_THRE != (serial_in(up, UART_LSR) & 1812 (UART_LSR_THRE | UART_LSR_DR))) { 1813 timeout--; 1814 if (!timeout) { 1815 /* Should *never* happen. we warn and carry on */ 1816 dev_crit(up->dev, "Errata i202: timedout %x\n", 1817 serial_in(up, UART_LSR)); 1818 break; 1819 } 1820 udelay(1); 1821 } 1822 } 1823 1824 #ifdef CONFIG_PM 1825 static void serial_omap_restore_context(struct uart_omap_port *up) 1826 { 1827 if (up->errata & UART_ERRATA_i202_MDR1_ACCESS) 1828 serial_omap_mdr1_errataset(up, UART_OMAP_MDR1_DISABLE); 1829 else 1830 serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE); 1831 1832 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */ 1833 serial_out(up, UART_EFR, UART_EFR_ECB); 1834 serial_out(up, UART_LCR, 0x0); /* Operational mode */ 1835 serial_out(up, UART_IER, 0x0); 1836 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */ 1837 serial_out(up, UART_DLL, up->dll); 1838 serial_out(up, UART_DLM, up->dlh); 1839 serial_out(up, UART_LCR, 0x0); /* Operational mode */ 1840 serial_out(up, UART_IER, up->ier); 1841 serial_out(up, UART_FCR, up->fcr); 1842 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A); 1843 serial_out(up, UART_MCR, up->mcr); 1844 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */ 1845 serial_out(up, UART_OMAP_SCR, up->scr); 1846 serial_out(up, UART_EFR, up->efr); 1847 serial_out(up, UART_LCR, up->lcr); 1848 if (up->errata & UART_ERRATA_i202_MDR1_ACCESS) 1849 serial_omap_mdr1_errataset(up, up->mdr1); 1850 else 1851 serial_out(up, UART_OMAP_MDR1, up->mdr1); 1852 serial_out(up, UART_OMAP_WER, up->wer); 1853 } 1854 1855 static int serial_omap_runtime_suspend(struct device *dev) 1856 { 1857 struct uart_omap_port *up = dev_get_drvdata(dev); 1858 1859 if (!up) 1860 return -EINVAL; 1861 1862 /* 1863 * When using 'no_console_suspend', the console UART must not be 1864 * suspended. Since driver suspend is managed by runtime suspend, 1865 * preventing runtime suspend (by returning error) will keep device 1866 * active during suspend. 1867 */ 1868 if (up->is_suspending && !console_suspend_enabled && 1869 uart_console(&up->port)) 1870 return -EBUSY; 1871 1872 up->context_loss_cnt = serial_omap_get_context_loss_count(up); 1873 1874 serial_omap_enable_wakeup(up, true); 1875 1876 up->latency = PM_QOS_CPU_LATENCY_DEFAULT_VALUE; 1877 schedule_work(&up->qos_work); 1878 1879 return 0; 1880 } 1881 1882 static int serial_omap_runtime_resume(struct device *dev) 1883 { 1884 struct uart_omap_port *up = dev_get_drvdata(dev); 1885 1886 int loss_cnt = serial_omap_get_context_loss_count(up); 1887 1888 serial_omap_enable_wakeup(up, false); 1889 1890 if (loss_cnt < 0) { 1891 dev_dbg(dev, "serial_omap_get_context_loss_count failed : %d\n", 1892 loss_cnt); 1893 serial_omap_restore_context(up); 1894 } else if (up->context_loss_cnt != loss_cnt) { 1895 serial_omap_restore_context(up); 1896 } 1897 up->latency = up->calc_latency; 1898 schedule_work(&up->qos_work); 1899 1900 return 0; 1901 } 1902 #endif 1903 1904 static const struct dev_pm_ops serial_omap_dev_pm_ops = { 1905 SET_SYSTEM_SLEEP_PM_OPS(serial_omap_suspend, serial_omap_resume) 1906 SET_RUNTIME_PM_OPS(serial_omap_runtime_suspend, 1907 serial_omap_runtime_resume, NULL) 1908 .prepare = serial_omap_prepare, 1909 .complete = serial_omap_complete, 1910 }; 1911 1912 #if defined(CONFIG_OF) 1913 static const struct of_device_id omap_serial_of_match[] = { 1914 { .compatible = "ti,omap2-uart" }, 1915 { .compatible = "ti,omap3-uart" }, 1916 { .compatible = "ti,omap4-uart" }, 1917 {}, 1918 }; 1919 MODULE_DEVICE_TABLE(of, omap_serial_of_match); 1920 #endif 1921 1922 static struct platform_driver serial_omap_driver = { 1923 .probe = serial_omap_probe, 1924 .remove = serial_omap_remove, 1925 .driver = { 1926 .name = OMAP_SERIAL_DRIVER_NAME, 1927 .pm = &serial_omap_dev_pm_ops, 1928 .of_match_table = of_match_ptr(omap_serial_of_match), 1929 }, 1930 }; 1931 1932 static int __init serial_omap_init(void) 1933 { 1934 int ret; 1935 1936 ret = uart_register_driver(&serial_omap_reg); 1937 if (ret != 0) 1938 return ret; 1939 ret = platform_driver_register(&serial_omap_driver); 1940 if (ret != 0) 1941 uart_unregister_driver(&serial_omap_reg); 1942 return ret; 1943 } 1944 1945 static void __exit serial_omap_exit(void) 1946 { 1947 platform_driver_unregister(&serial_omap_driver); 1948 uart_unregister_driver(&serial_omap_reg); 1949 } 1950 1951 module_init(serial_omap_init); 1952 module_exit(serial_omap_exit); 1953 1954 MODULE_DESCRIPTION("OMAP High Speed UART driver"); 1955 MODULE_LICENSE("GPL"); 1956 MODULE_AUTHOR("Texas Instruments Inc"); 1957