xref: /linux/drivers/tty/serial/men_z135_uart.c (revision 4b660dbd9ee2059850fd30e0df420ca7a38a1856) 
1 // SPDX-License-Identifier: GPL-2.0
2 /*
3  * MEN 16z135 High Speed UART
4  *
5  * Copyright (C) 2014 MEN Mikroelektronik GmbH (www.men.de)
6  * Author: Johannes Thumshirn <johannes.thumshirn@men.de>
7  */
8 #define pr_fmt(fmt) KBUILD_MODNAME ":" fmt
9 
10 #include <linux/kernel.h>
11 #include <linux/module.h>
12 #include <linux/interrupt.h>
13 #include <linux/serial_core.h>
14 #include <linux/ioport.h>
15 #include <linux/io.h>
16 #include <linux/tty_flip.h>
17 #include <linux/bitops.h>
18 #include <linux/mcb.h>
19 
20 #define MEN_Z135_MAX_PORTS		12
21 #define MEN_Z135_BASECLK		29491200
22 #define MEN_Z135_FIFO_SIZE		1024
23 #define MEN_Z135_FIFO_WATERMARK		1020
24 
25 #define MEN_Z135_STAT_REG		0x0
26 #define MEN_Z135_RX_RAM			0x4
27 #define MEN_Z135_TX_RAM			0x400
28 #define MEN_Z135_RX_CTRL		0x800
29 #define MEN_Z135_TX_CTRL		0x804
30 #define MEN_Z135_CONF_REG		0x808
31 #define MEN_Z135_UART_FREQ		0x80c
32 #define MEN_Z135_BAUD_REG		0x810
33 #define MEN_Z135_TIMEOUT		0x814
34 
35 #define IRQ_ID(x) ((x) & 0x1f)
36 
37 #define MEN_Z135_IER_RXCIEN BIT(0)		/* RX Space IRQ */
38 #define MEN_Z135_IER_TXCIEN BIT(1)		/* TX Space IRQ */
39 #define MEN_Z135_IER_RLSIEN BIT(2)		/* Receiver Line Status IRQ */
40 #define MEN_Z135_IER_MSIEN  BIT(3)		/* Modem Status IRQ */
41 #define MEN_Z135_ALL_IRQS (MEN_Z135_IER_RXCIEN		\
42 				| MEN_Z135_IER_RLSIEN	\
43 				| MEN_Z135_IER_MSIEN	\
44 				| MEN_Z135_IER_TXCIEN)
45 
46 #define MEN_Z135_MCR_DTR	BIT(24)
47 #define MEN_Z135_MCR_RTS	BIT(25)
48 #define MEN_Z135_MCR_OUT1	BIT(26)
49 #define MEN_Z135_MCR_OUT2	BIT(27)
50 #define MEN_Z135_MCR_LOOP	BIT(28)
51 #define MEN_Z135_MCR_RCFC	BIT(29)
52 
53 #define MEN_Z135_MSR_DCTS	BIT(0)
54 #define MEN_Z135_MSR_DDSR	BIT(1)
55 #define MEN_Z135_MSR_DRI	BIT(2)
56 #define MEN_Z135_MSR_DDCD	BIT(3)
57 #define MEN_Z135_MSR_CTS	BIT(4)
58 #define MEN_Z135_MSR_DSR	BIT(5)
59 #define MEN_Z135_MSR_RI		BIT(6)
60 #define MEN_Z135_MSR_DCD	BIT(7)
61 
62 #define MEN_Z135_LCR_SHIFT 8	/* LCR shift mask */
63 
64 #define MEN_Z135_WL5 0		/* CS5 */
65 #define MEN_Z135_WL6 1		/* CS6 */
66 #define MEN_Z135_WL7 2		/* CS7 */
67 #define MEN_Z135_WL8 3		/* CS8 */
68 
69 #define MEN_Z135_STB_SHIFT 2	/* Stopbits */
70 #define MEN_Z135_NSTB1 0
71 #define MEN_Z135_NSTB2 1
72 
73 #define MEN_Z135_PEN_SHIFT 3	/* Parity enable */
74 #define MEN_Z135_PAR_DIS 0
75 #define MEN_Z135_PAR_ENA 1
76 
77 #define MEN_Z135_PTY_SHIFT 4	/* Parity type */
78 #define MEN_Z135_PTY_ODD 0
79 #define MEN_Z135_PTY_EVN 1
80 
81 #define MEN_Z135_LSR_DR BIT(0)
82 #define MEN_Z135_LSR_OE BIT(1)
83 #define MEN_Z135_LSR_PE BIT(2)
84 #define MEN_Z135_LSR_FE BIT(3)
85 #define MEN_Z135_LSR_BI BIT(4)
86 #define MEN_Z135_LSR_THEP BIT(5)
87 #define MEN_Z135_LSR_TEXP BIT(6)
88 #define MEN_Z135_LSR_RXFIFOERR BIT(7)
89 
90 #define MEN_Z135_IRQ_ID_RLS BIT(0)
91 #define MEN_Z135_IRQ_ID_RDA BIT(1)
92 #define MEN_Z135_IRQ_ID_CTI BIT(2)
93 #define MEN_Z135_IRQ_ID_TSA BIT(3)
94 #define MEN_Z135_IRQ_ID_MST BIT(4)
95 
96 #define LCR(x) (((x) >> MEN_Z135_LCR_SHIFT) & 0xff)
97 
98 #define BYTES_TO_ALIGN(x) ((x) & 0x3)
99 
100 static int line;
101 
102 static int txlvl = 5;
103 module_param(txlvl, int, S_IRUGO);
104 MODULE_PARM_DESC(txlvl, "TX IRQ trigger level 0-7, default 5 (128 byte)");
105 
106 static int rxlvl = 6;
107 module_param(rxlvl, int, S_IRUGO);
108 MODULE_PARM_DESC(rxlvl, "RX IRQ trigger level 0-7, default 6 (256 byte)");
109 
110 static int align;
111 module_param(align, int, S_IRUGO);
112 MODULE_PARM_DESC(align, "Keep hardware FIFO write pointer aligned, default 0");
113 
114 static uint rx_timeout;
115 module_param(rx_timeout, uint, S_IRUGO);
116 MODULE_PARM_DESC(rx_timeout, "RX timeout. "
117 		"Timeout in seconds = (timeout_reg * baud_reg * 4) / freq_reg");
118 
119 struct men_z135_port {
120 	struct uart_port port;
121 	struct mcb_device *mdev;
122 	struct resource *mem;
123 	unsigned char *rxbuf;
124 	u32 stat_reg;
125 	spinlock_t lock;
126 	bool automode;
127 };
128 #define to_men_z135(port) container_of((port), struct men_z135_port, port)
129 
130 /**
131  * men_z135_reg_set() - Set value in register
132  * @uart: The UART port
133  * @addr: Register address
134  * @val: value to set
135  */
136 static inline void men_z135_reg_set(struct men_z135_port *uart,
137 				u32 addr, u32 val)
138 {
139 	struct uart_port *port = &uart->port;
140 	unsigned long flags;
141 	u32 reg;
142 
143 	spin_lock_irqsave(&uart->lock, flags);
144 
145 	reg = ioread32(port->membase + addr);
146 	reg |= val;
147 	iowrite32(reg, port->membase + addr);
148 
149 	spin_unlock_irqrestore(&uart->lock, flags);
150 }
151 
152 /**
153  * men_z135_reg_clr() - Unset value in register
154  * @uart: The UART port
155  * @addr: Register address
156  * @val: value to clear
157  */
158 static void men_z135_reg_clr(struct men_z135_port *uart,
159 				u32 addr, u32 val)
160 {
161 	struct uart_port *port = &uart->port;
162 	unsigned long flags;
163 	u32 reg;
164 
165 	spin_lock_irqsave(&uart->lock, flags);
166 
167 	reg = ioread32(port->membase + addr);
168 	reg &= ~val;
169 	iowrite32(reg, port->membase + addr);
170 
171 	spin_unlock_irqrestore(&uart->lock, flags);
172 }
173 
174 /**
175  * men_z135_handle_modem_status() - Handle change of modem status
176  * @uart: The UART port
177  *
178  * Handle change of modem status register. This is done by reading the "delta"
179  * versions of DCD (Data Carrier Detect) and CTS (Clear To Send).
180  */
181 static void men_z135_handle_modem_status(struct men_z135_port *uart)
182 {
183 	u8 msr;
184 
185 	msr = (uart->stat_reg >> 8) & 0xff;
186 
187 	if (msr & MEN_Z135_MSR_DDCD)
188 		uart_handle_dcd_change(&uart->port,
189 				msr & MEN_Z135_MSR_DCD);
190 	if (msr & MEN_Z135_MSR_DCTS)
191 		uart_handle_cts_change(&uart->port,
192 				msr & MEN_Z135_MSR_CTS);
193 }
194 
195 static void men_z135_handle_lsr(struct men_z135_port *uart)
196 {
197 	struct uart_port *port = &uart->port;
198 	u8 lsr;
199 
200 	lsr = (uart->stat_reg >> 16) & 0xff;
201 
202 	if (lsr & MEN_Z135_LSR_OE)
203 		port->icount.overrun++;
204 	if (lsr & MEN_Z135_LSR_PE)
205 		port->icount.parity++;
206 	if (lsr & MEN_Z135_LSR_FE)
207 		port->icount.frame++;
208 	if (lsr & MEN_Z135_LSR_BI) {
209 		port->icount.brk++;
210 		uart_handle_break(port);
211 	}
212 }
213 
214 /**
215  * get_rx_fifo_content() - Get the number of bytes in RX FIFO
216  * @uart: The UART port
217  *
218  * Read RXC register from hardware and return current FIFO fill size.
219  */
220 static u16 get_rx_fifo_content(struct men_z135_port *uart)
221 {
222 	struct uart_port *port = &uart->port;
223 	u32 stat_reg;
224 	u16 rxc;
225 	u8 rxc_lo;
226 	u8 rxc_hi;
227 
228 	stat_reg = ioread32(port->membase + MEN_Z135_STAT_REG);
229 	rxc_lo = stat_reg >> 24;
230 	rxc_hi = (stat_reg & 0xC0) >> 6;
231 
232 	rxc = rxc_lo | (rxc_hi << 8);
233 
234 	return rxc;
235 }
236 
237 /**
238  * men_z135_handle_rx() - RX tasklet routine
239  * @uart: Pointer to struct men_z135_port
240  *
241  * Copy from RX FIFO and acknowledge number of bytes copied.
242  */
243 static void men_z135_handle_rx(struct men_z135_port *uart)
244 {
245 	struct uart_port *port = &uart->port;
246 	struct tty_port *tport = &port->state->port;
247 	int copied;
248 	u16 size;
249 	int room;
250 
251 	size = get_rx_fifo_content(uart);
252 
253 	if (size == 0)
254 		return;
255 
256 	/* Avoid accidently accessing TX FIFO instead of RX FIFO. Last
257 	 * longword in RX FIFO cannot be read.(0x004-0x3FF)
258 	 */
259 	if (size > MEN_Z135_FIFO_WATERMARK)
260 		size = MEN_Z135_FIFO_WATERMARK;
261 
262 	room = tty_buffer_request_room(tport, size);
263 	if (room != size)
264 		dev_warn(&uart->mdev->dev,
265 			"Not enough room in flip buffer, truncating to %d\n",
266 			room);
267 
268 	if (room == 0)
269 		return;
270 
271 	memcpy_fromio(uart->rxbuf, port->membase + MEN_Z135_RX_RAM, room);
272 	/* Be sure to first copy all data and then acknowledge it */
273 	mb();
274 	iowrite32(room, port->membase +  MEN_Z135_RX_CTRL);
275 
276 	copied = tty_insert_flip_string(tport, uart->rxbuf, room);
277 	if (copied != room)
278 		dev_warn(&uart->mdev->dev,
279 			"Only copied %d instead of %d bytes\n",
280 			copied, room);
281 
282 	port->icount.rx += copied;
283 
284 	tty_flip_buffer_push(tport);
285 
286 }
287 
288 /**
289  * men_z135_handle_tx() - TX tasklet routine
290  * @uart: Pointer to struct men_z135_port
291  *
292  */
293 static void men_z135_handle_tx(struct men_z135_port *uart)
294 {
295 	struct uart_port *port = &uart->port;
296 	struct circ_buf *xmit = &port->state->xmit;
297 	u32 txc;
298 	u32 wptr;
299 	int qlen;
300 	int n;
301 	int txfree;
302 	int head;
303 	int tail;
304 	int s;
305 
306 	if (uart_circ_empty(xmit))
307 		goto out;
308 
309 	if (uart_tx_stopped(port))
310 		goto out;
311 
312 	if (port->x_char)
313 		goto out;
314 
315 	/* calculate bytes to copy */
316 	qlen = uart_circ_chars_pending(xmit);
317 	if (qlen <= 0)
318 		goto out;
319 
320 	wptr = ioread32(port->membase + MEN_Z135_TX_CTRL);
321 	txc = (wptr >> 16) & 0x3ff;
322 	wptr &= 0x3ff;
323 
324 	if (txc > MEN_Z135_FIFO_WATERMARK)
325 		txc = MEN_Z135_FIFO_WATERMARK;
326 
327 	txfree = MEN_Z135_FIFO_WATERMARK - txc;
328 	if (txfree <= 0) {
329 		dev_err(&uart->mdev->dev,
330 			"Not enough room in TX FIFO have %d, need %d\n",
331 			txfree, qlen);
332 		goto irq_en;
333 	}
334 
335 	/* if we're not aligned, it's better to copy only 1 or 2 bytes and
336 	 * then the rest.
337 	 */
338 	if (align && qlen >= 3 && BYTES_TO_ALIGN(wptr))
339 		n = 4 - BYTES_TO_ALIGN(wptr);
340 	else if (qlen > txfree)
341 		n = txfree;
342 	else
343 		n = qlen;
344 
345 	if (n <= 0)
346 		goto irq_en;
347 
348 	head = xmit->head & (UART_XMIT_SIZE - 1);
349 	tail = xmit->tail & (UART_XMIT_SIZE - 1);
350 
351 	s = ((head >= tail) ? head : UART_XMIT_SIZE) - tail;
352 	n = min(n, s);
353 
354 	memcpy_toio(port->membase + MEN_Z135_TX_RAM, &xmit->buf[xmit->tail], n);
355 	iowrite32(n & 0x3ff, port->membase + MEN_Z135_TX_CTRL);
356 	uart_xmit_advance(port, n);
357 
358 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
359 		uart_write_wakeup(port);
360 
361 irq_en:
362 	if (!uart_circ_empty(xmit))
363 		men_z135_reg_set(uart, MEN_Z135_CONF_REG, MEN_Z135_IER_TXCIEN);
364 	else
365 		men_z135_reg_clr(uart, MEN_Z135_CONF_REG, MEN_Z135_IER_TXCIEN);
366 
367 out:
368 	return;
369 
370 }
371 
372 /**
373  * men_z135_intr() - Handle legacy IRQs
374  * @irq: The IRQ number
375  * @data: Pointer to UART port
376  *
377  * Check IIR register to find the cause of the interrupt and handle it.
378  * It is possible that multiple interrupts reason bits are set and reading
379  * the IIR is a destructive read, so we always need to check for all possible
380  * interrupts and handle them.
381  */
382 static irqreturn_t men_z135_intr(int irq, void *data)
383 {
384 	struct men_z135_port *uart = (struct men_z135_port *)data;
385 	struct uart_port *port = &uart->port;
386 	bool handled = false;
387 	int irq_id;
388 
389 	uart->stat_reg = ioread32(port->membase + MEN_Z135_STAT_REG);
390 	irq_id = IRQ_ID(uart->stat_reg);
391 
392 	if (!irq_id)
393 		goto out;
394 
395 	uart_port_lock(port);
396 	/* It's save to write to IIR[7:6] RXC[9:8] */
397 	iowrite8(irq_id, port->membase + MEN_Z135_STAT_REG);
398 
399 	if (irq_id & MEN_Z135_IRQ_ID_RLS) {
400 		men_z135_handle_lsr(uart);
401 		handled = true;
402 	}
403 
404 	if (irq_id & (MEN_Z135_IRQ_ID_RDA | MEN_Z135_IRQ_ID_CTI)) {
405 		if (irq_id & MEN_Z135_IRQ_ID_CTI)
406 			dev_dbg(&uart->mdev->dev, "Character Timeout Indication\n");
407 		men_z135_handle_rx(uart);
408 		handled = true;
409 	}
410 
411 	if (irq_id & MEN_Z135_IRQ_ID_TSA) {
412 		men_z135_handle_tx(uart);
413 		handled = true;
414 	}
415 
416 	if (irq_id & MEN_Z135_IRQ_ID_MST) {
417 		men_z135_handle_modem_status(uart);
418 		handled = true;
419 	}
420 
421 	uart_port_unlock(port);
422 out:
423 	return IRQ_RETVAL(handled);
424 }
425 
426 /**
427  * men_z135_request_irq() - Request IRQ for 16z135 core
428  * @uart: z135 private uart port structure
429  *
430  * Request an IRQ for 16z135 to use. First try using MSI, if it fails
431  * fall back to using legacy interrupts.
432  */
433 static int men_z135_request_irq(struct men_z135_port *uart)
434 {
435 	struct device *dev = &uart->mdev->dev;
436 	struct uart_port *port = &uart->port;
437 	int err = 0;
438 
439 	err = request_irq(port->irq, men_z135_intr, IRQF_SHARED,
440 			"men_z135_intr", uart);
441 	if (err)
442 		dev_err(dev, "Error %d getting interrupt\n", err);
443 
444 	return err;
445 }
446 
447 /**
448  * men_z135_tx_empty() - Handle tx_empty call
449  * @port: The UART port
450  *
451  * This function tests whether the TX FIFO and shifter for the port
452  * described by @port is empty.
453  */
454 static unsigned int men_z135_tx_empty(struct uart_port *port)
455 {
456 	u32 wptr;
457 	u16 txc;
458 
459 	wptr = ioread32(port->membase + MEN_Z135_TX_CTRL);
460 	txc = (wptr >> 16) & 0x3ff;
461 
462 	if (txc == 0)
463 		return TIOCSER_TEMT;
464 	else
465 		return 0;
466 }
467 
468 /**
469  * men_z135_set_mctrl() - Set modem control lines
470  * @port: The UART port
471  * @mctrl: The modem control lines
472  *
473  * This function sets the modem control lines for a port described by @port
474  * to the state described by @mctrl
475  */
476 static void men_z135_set_mctrl(struct uart_port *port, unsigned int mctrl)
477 {
478 	u32 old;
479 	u32 conf_reg;
480 
481 	conf_reg = old = ioread32(port->membase + MEN_Z135_CONF_REG);
482 	if (mctrl & TIOCM_RTS)
483 		conf_reg |= MEN_Z135_MCR_RTS;
484 	else
485 		conf_reg &= ~MEN_Z135_MCR_RTS;
486 
487 	if (mctrl & TIOCM_DTR)
488 		conf_reg |= MEN_Z135_MCR_DTR;
489 	else
490 		conf_reg &= ~MEN_Z135_MCR_DTR;
491 
492 	if (mctrl & TIOCM_OUT1)
493 		conf_reg |= MEN_Z135_MCR_OUT1;
494 	else
495 		conf_reg &= ~MEN_Z135_MCR_OUT1;
496 
497 	if (mctrl & TIOCM_OUT2)
498 		conf_reg |= MEN_Z135_MCR_OUT2;
499 	else
500 		conf_reg &= ~MEN_Z135_MCR_OUT2;
501 
502 	if (mctrl & TIOCM_LOOP)
503 		conf_reg |= MEN_Z135_MCR_LOOP;
504 	else
505 		conf_reg &= ~MEN_Z135_MCR_LOOP;
506 
507 	if (conf_reg != old)
508 		iowrite32(conf_reg, port->membase + MEN_Z135_CONF_REG);
509 }
510 
511 /**
512  * men_z135_get_mctrl() - Get modem control lines
513  * @port: The UART port
514  *
515  * Retruns the current state of modem control inputs.
516  */
517 static unsigned int men_z135_get_mctrl(struct uart_port *port)
518 {
519 	unsigned int mctrl = 0;
520 	u8 msr;
521 
522 	msr = ioread8(port->membase + MEN_Z135_STAT_REG + 1);
523 
524 	if (msr & MEN_Z135_MSR_CTS)
525 		mctrl |= TIOCM_CTS;
526 	if (msr & MEN_Z135_MSR_DSR)
527 		mctrl |= TIOCM_DSR;
528 	if (msr & MEN_Z135_MSR_RI)
529 		mctrl |= TIOCM_RI;
530 	if (msr & MEN_Z135_MSR_DCD)
531 		mctrl |= TIOCM_CAR;
532 
533 	return mctrl;
534 }
535 
536 /**
537  * men_z135_stop_tx() - Stop transmitting characters
538  * @port: The UART port
539  *
540  * Stop transmitting characters. This might be due to CTS line becomming
541  * inactive or the tty layer indicating we want to stop transmission due to
542  * an XOFF character.
543  */
544 static void men_z135_stop_tx(struct uart_port *port)
545 {
546 	struct men_z135_port *uart = to_men_z135(port);
547 
548 	men_z135_reg_clr(uart, MEN_Z135_CONF_REG, MEN_Z135_IER_TXCIEN);
549 }
550 
551 /*
552  * men_z135_disable_ms() - Disable Modem Status
553  * port: The UART port
554  *
555  * Enable Modem Status IRQ.
556  */
557 static void men_z135_disable_ms(struct uart_port *port)
558 {
559 	struct men_z135_port *uart = to_men_z135(port);
560 
561 	men_z135_reg_clr(uart, MEN_Z135_CONF_REG, MEN_Z135_IER_MSIEN);
562 }
563 
564 /**
565  * men_z135_start_tx() - Start transmitting characters
566  * @port: The UART port
567  *
568  * Start transmitting character. This actually doesn't transmit anything, but
569  * fires off the TX tasklet.
570  */
571 static void men_z135_start_tx(struct uart_port *port)
572 {
573 	struct men_z135_port *uart = to_men_z135(port);
574 
575 	if (uart->automode)
576 		men_z135_disable_ms(port);
577 
578 	men_z135_handle_tx(uart);
579 }
580 
581 /**
582  * men_z135_stop_rx() - Stop receiving characters
583  * @port: The UART port
584  *
585  * Stop receiving characters; the port is in the process of being closed.
586  */
587 static void men_z135_stop_rx(struct uart_port *port)
588 {
589 	struct men_z135_port *uart = to_men_z135(port);
590 
591 	men_z135_reg_clr(uart, MEN_Z135_CONF_REG, MEN_Z135_IER_RXCIEN);
592 }
593 
594 /**
595  * men_z135_enable_ms() - Enable Modem Status
596  * @port: the port
597  *
598  * Enable Modem Status IRQ.
599  */
600 static void men_z135_enable_ms(struct uart_port *port)
601 {
602 	struct men_z135_port *uart = to_men_z135(port);
603 
604 	men_z135_reg_set(uart, MEN_Z135_CONF_REG, MEN_Z135_IER_MSIEN);
605 }
606 
607 static int men_z135_startup(struct uart_port *port)
608 {
609 	struct men_z135_port *uart = to_men_z135(port);
610 	int err;
611 	u32 conf_reg = 0;
612 
613 	err = men_z135_request_irq(uart);
614 	if (err)
615 		return -ENODEV;
616 
617 	conf_reg = ioread32(port->membase + MEN_Z135_CONF_REG);
618 
619 	/* Activate all but TX space available IRQ */
620 	conf_reg |= MEN_Z135_ALL_IRQS & ~MEN_Z135_IER_TXCIEN;
621 	conf_reg &= ~(0xff << 16);
622 	conf_reg |= (txlvl << 16);
623 	conf_reg |= (rxlvl << 20);
624 
625 	iowrite32(conf_reg, port->membase + MEN_Z135_CONF_REG);
626 
627 	if (rx_timeout)
628 		iowrite32(rx_timeout, port->membase + MEN_Z135_TIMEOUT);
629 
630 	return 0;
631 }
632 
633 static void men_z135_shutdown(struct uart_port *port)
634 {
635 	struct men_z135_port *uart = to_men_z135(port);
636 	u32 conf_reg = 0;
637 
638 	conf_reg |= MEN_Z135_ALL_IRQS;
639 
640 	men_z135_reg_clr(uart, MEN_Z135_CONF_REG, conf_reg);
641 
642 	free_irq(uart->port.irq, uart);
643 }
644 
645 static void men_z135_set_termios(struct uart_port *port,
646 				 struct ktermios *termios,
647 				 const struct ktermios *old)
648 {
649 	struct men_z135_port *uart = to_men_z135(port);
650 	unsigned int baud;
651 	u32 conf_reg;
652 	u32 bd_reg;
653 	u32 uart_freq;
654 	u8 lcr;
655 
656 	conf_reg = ioread32(port->membase + MEN_Z135_CONF_REG);
657 	lcr = LCR(conf_reg);
658 
659 	/* byte size */
660 	switch (termios->c_cflag & CSIZE) {
661 	case CS5:
662 		lcr |= MEN_Z135_WL5;
663 		break;
664 	case CS6:
665 		lcr |= MEN_Z135_WL6;
666 		break;
667 	case CS7:
668 		lcr |= MEN_Z135_WL7;
669 		break;
670 	case CS8:
671 		lcr |= MEN_Z135_WL8;
672 		break;
673 	}
674 
675 	/* stop bits */
676 	if (termios->c_cflag & CSTOPB)
677 		lcr |= MEN_Z135_NSTB2 << MEN_Z135_STB_SHIFT;
678 
679 	/* parity */
680 	if (termios->c_cflag & PARENB) {
681 		lcr |= MEN_Z135_PAR_ENA << MEN_Z135_PEN_SHIFT;
682 
683 		if (termios->c_cflag & PARODD)
684 			lcr |= MEN_Z135_PTY_ODD << MEN_Z135_PTY_SHIFT;
685 		else
686 			lcr |= MEN_Z135_PTY_EVN << MEN_Z135_PTY_SHIFT;
687 	} else
688 		lcr |= MEN_Z135_PAR_DIS << MEN_Z135_PEN_SHIFT;
689 
690 	conf_reg |= MEN_Z135_IER_MSIEN;
691 	if (termios->c_cflag & CRTSCTS) {
692 		conf_reg |= MEN_Z135_MCR_RCFC;
693 		uart->automode = true;
694 		termios->c_cflag &= ~CLOCAL;
695 	} else {
696 		conf_reg &= ~MEN_Z135_MCR_RCFC;
697 		uart->automode = false;
698 	}
699 
700 	termios->c_cflag &= ~CMSPAR; /* Mark/Space parity is not supported */
701 
702 	conf_reg |= lcr << MEN_Z135_LCR_SHIFT;
703 	iowrite32(conf_reg, port->membase + MEN_Z135_CONF_REG);
704 
705 	uart_freq = ioread32(port->membase + MEN_Z135_UART_FREQ);
706 	if (uart_freq == 0)
707 		uart_freq = MEN_Z135_BASECLK;
708 
709 	baud = uart_get_baud_rate(port, termios, old, 0, uart_freq / 16);
710 
711 	uart_port_lock_irq(port);
712 	if (tty_termios_baud_rate(termios))
713 		tty_termios_encode_baud_rate(termios, baud, baud);
714 
715 	bd_reg = uart_freq / (4 * baud);
716 	iowrite32(bd_reg, port->membase + MEN_Z135_BAUD_REG);
717 
718 	uart_update_timeout(port, termios->c_cflag, baud);
719 	uart_port_unlock_irq(port);
720 }
721 
722 static const char *men_z135_type(struct uart_port *port)
723 {
724 	return KBUILD_MODNAME;
725 }
726 
727 static void men_z135_release_port(struct uart_port *port)
728 {
729 	struct men_z135_port *uart = to_men_z135(port);
730 
731 	iounmap(port->membase);
732 	port->membase = NULL;
733 
734 	mcb_release_mem(uart->mem);
735 }
736 
737 static int men_z135_request_port(struct uart_port *port)
738 {
739 	struct men_z135_port *uart = to_men_z135(port);
740 	struct mcb_device *mdev = uart->mdev;
741 	struct resource *mem;
742 
743 	mem = mcb_request_mem(uart->mdev, dev_name(&mdev->dev));
744 	if (IS_ERR(mem))
745 		return PTR_ERR(mem);
746 
747 	port->mapbase = mem->start;
748 	uart->mem = mem;
749 
750 	port->membase = ioremap(mem->start, resource_size(mem));
751 	if (port->membase == NULL) {
752 		mcb_release_mem(mem);
753 		return -ENOMEM;
754 	}
755 
756 	return 0;
757 }
758 
759 static void men_z135_config_port(struct uart_port *port, int type)
760 {
761 	port->type = PORT_MEN_Z135;
762 	men_z135_request_port(port);
763 }
764 
765 static int men_z135_verify_port(struct uart_port *port,
766 				struct serial_struct *serinfo)
767 {
768 	return -EINVAL;
769 }
770 
771 static const struct uart_ops men_z135_ops = {
772 	.tx_empty = men_z135_tx_empty,
773 	.set_mctrl = men_z135_set_mctrl,
774 	.get_mctrl = men_z135_get_mctrl,
775 	.stop_tx = men_z135_stop_tx,
776 	.start_tx = men_z135_start_tx,
777 	.stop_rx = men_z135_stop_rx,
778 	.enable_ms = men_z135_enable_ms,
779 	.startup = men_z135_startup,
780 	.shutdown = men_z135_shutdown,
781 	.set_termios = men_z135_set_termios,
782 	.type = men_z135_type,
783 	.release_port = men_z135_release_port,
784 	.request_port = men_z135_request_port,
785 	.config_port = men_z135_config_port,
786 	.verify_port = men_z135_verify_port,
787 };
788 
789 static struct uart_driver men_z135_driver = {
790 	.owner = THIS_MODULE,
791 	.driver_name = KBUILD_MODNAME,
792 	.dev_name = "ttyHSU",
793 	.major = 0,
794 	.minor = 0,
795 	.nr = MEN_Z135_MAX_PORTS,
796 };
797 
798 /**
799  * men_z135_probe() - Probe a z135 instance
800  * @mdev: The MCB device
801  * @id: The MCB device ID
802  *
803  * men_z135_probe does the basic setup of hardware resources and registers the
804  * new uart port to the tty layer.
805  */
806 static int men_z135_probe(struct mcb_device *mdev,
807 			const struct mcb_device_id *id)
808 {
809 	struct men_z135_port *uart;
810 	struct resource *mem;
811 	struct device *dev;
812 	int err;
813 
814 	dev = &mdev->dev;
815 
816 	uart = devm_kzalloc(dev, sizeof(struct men_z135_port), GFP_KERNEL);
817 	if (!uart)
818 		return -ENOMEM;
819 
820 	uart->rxbuf = (unsigned char *)__get_free_page(GFP_KERNEL);
821 	if (!uart->rxbuf)
822 		return -ENOMEM;
823 
824 	mem = &mdev->mem;
825 
826 	mcb_set_drvdata(mdev, uart);
827 
828 	uart->port.uartclk = MEN_Z135_BASECLK * 16;
829 	uart->port.fifosize = MEN_Z135_FIFO_SIZE;
830 	uart->port.iotype = UPIO_MEM;
831 	uart->port.ops = &men_z135_ops;
832 	uart->port.irq = mcb_get_irq(mdev);
833 	uart->port.flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
834 	uart->port.line = line++;
835 	uart->port.dev = dev;
836 	uart->port.type = PORT_MEN_Z135;
837 	uart->port.mapbase = mem->start;
838 	uart->port.membase = NULL;
839 	uart->mdev = mdev;
840 
841 	spin_lock_init(&uart->lock);
842 
843 	err = uart_add_one_port(&men_z135_driver, &uart->port);
844 	if (err)
845 		goto err;
846 
847 	return 0;
848 
849 err:
850 	free_page((unsigned long) uart->rxbuf);
851 	dev_err(dev, "Failed to add UART: %d\n", err);
852 
853 	return err;
854 }
855 
856 /**
857  * men_z135_remove() - Remove a z135 instance from the system
858  *
859  * @mdev: The MCB device
860  */
861 static void men_z135_remove(struct mcb_device *mdev)
862 {
863 	struct men_z135_port *uart = mcb_get_drvdata(mdev);
864 
865 	line--;
866 	uart_remove_one_port(&men_z135_driver, &uart->port);
867 	free_page((unsigned long) uart->rxbuf);
868 }
869 
870 static const struct mcb_device_id men_z135_ids[] = {
871 	{ .device = 0x87 },
872 	{ }
873 };
874 MODULE_DEVICE_TABLE(mcb, men_z135_ids);
875 
876 static struct mcb_driver mcb_driver = {
877 	.driver = {
878 		.name = "z135-uart",
879 		.owner = THIS_MODULE,
880 	},
881 	.probe = men_z135_probe,
882 	.remove = men_z135_remove,
883 	.id_table = men_z135_ids,
884 };
885 
886 /**
887  * men_z135_init() - Driver Registration Routine
888  *
889  * men_z135_init is the first routine called when the driver is loaded. All it
890  * does is register with the legacy MEN Chameleon subsystem.
891  */
892 static int __init men_z135_init(void)
893 {
894 	int err;
895 
896 	err = uart_register_driver(&men_z135_driver);
897 	if (err) {
898 		pr_err("Failed to register UART: %d\n", err);
899 		return err;
900 	}
901 
902 	err = mcb_register_driver(&mcb_driver);
903 	if  (err) {
904 		pr_err("Failed to register MCB driver: %d\n", err);
905 		uart_unregister_driver(&men_z135_driver);
906 		return err;
907 	}
908 
909 	return 0;
910 }
911 module_init(men_z135_init);
912 
913 /**
914  * men_z135_exit() - Driver Exit Routine
915  *
916  * men_z135_exit is called just before the driver is removed from memory.
917  */
918 static void __exit men_z135_exit(void)
919 {
920 	mcb_unregister_driver(&mcb_driver);
921 	uart_unregister_driver(&men_z135_driver);
922 }
923 module_exit(men_z135_exit);
924 
925 MODULE_AUTHOR("Johannes Thumshirn <johannes.thumshirn@men.de>");
926 MODULE_LICENSE("GPL v2");
927 MODULE_DESCRIPTION("MEN 16z135 High Speed UART");
928 MODULE_ALIAS("mcb:16z135");
929 MODULE_IMPORT_NS(MCB);
930