1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Freescale lpuart serial port driver 4 * 5 * Copyright 2012-2014 Freescale Semiconductor, Inc. 6 */ 7 8 #include <linux/bitfield.h> 9 #include <linux/bits.h> 10 #include <linux/clk.h> 11 #include <linux/console.h> 12 #include <linux/delay.h> 13 #include <linux/dma-mapping.h> 14 #include <linux/dmaengine.h> 15 #include <linux/dmapool.h> 16 #include <linux/io.h> 17 #include <linux/iopoll.h> 18 #include <linux/irq.h> 19 #include <linux/module.h> 20 #include <linux/of.h> 21 #include <linux/of_dma.h> 22 #include <linux/pinctrl/consumer.h> 23 #include <linux/platform_device.h> 24 #include <linux/pm_runtime.h> 25 #include <linux/serial_core.h> 26 #include <linux/slab.h> 27 #include <linux/tty_flip.h> 28 29 /* All registers are 8-bit width */ 30 #define UARTBDH 0x00 31 #define UARTBDL 0x01 32 #define UARTCR1 0x02 33 #define UARTCR2 0x03 34 #define UARTSR1 0x04 35 #define UARTCR3 0x06 36 #define UARTDR 0x07 37 #define UARTCR4 0x0a 38 #define UARTCR5 0x0b 39 #define UARTMODEM 0x0d 40 #define UARTPFIFO 0x10 41 #define UARTCFIFO 0x11 42 #define UARTSFIFO 0x12 43 #define UARTTWFIFO 0x13 44 #define UARTTCFIFO 0x14 45 #define UARTRWFIFO 0x15 46 47 #define UARTBDH_LBKDIE 0x80 48 #define UARTBDH_RXEDGIE 0x40 49 #define UARTBDH_SBR_MASK 0x1f 50 51 #define UARTCR1_LOOPS 0x80 52 #define UARTCR1_RSRC 0x20 53 #define UARTCR1_M 0x10 54 #define UARTCR1_WAKE 0x08 55 #define UARTCR1_ILT 0x04 56 #define UARTCR1_PE 0x02 57 #define UARTCR1_PT 0x01 58 59 #define UARTCR2_TIE 0x80 60 #define UARTCR2_TCIE 0x40 61 #define UARTCR2_RIE 0x20 62 #define UARTCR2_ILIE 0x10 63 #define UARTCR2_TE 0x08 64 #define UARTCR2_RE 0x04 65 #define UARTCR2_RWU 0x02 66 #define UARTCR2_SBK 0x01 67 68 #define UARTSR1_TDRE 0x80 69 #define UARTSR1_TC 0x40 70 #define UARTSR1_RDRF 0x20 71 #define UARTSR1_IDLE 0x10 72 #define UARTSR1_OR 0x08 73 #define UARTSR1_NF 0x04 74 #define UARTSR1_FE 0x02 75 #define UARTSR1_PE 0x01 76 77 #define UARTCR3_R8 0x80 78 #define UARTCR3_T8 0x40 79 #define UARTCR3_TXDIR 0x20 80 #define UARTCR3_TXINV 0x10 81 #define UARTCR3_ORIE 0x08 82 #define UARTCR3_NEIE 0x04 83 #define UARTCR3_FEIE 0x02 84 #define UARTCR3_PEIE 0x01 85 86 #define UARTCR4_MAEN1 0x80 87 #define UARTCR4_MAEN2 0x40 88 #define UARTCR4_M10 0x20 89 #define UARTCR4_BRFA_MASK 0x1f 90 #define UARTCR4_BRFA_OFF 0 91 92 #define UARTCR5_TDMAS 0x80 93 #define UARTCR5_RDMAS 0x20 94 95 #define UARTMODEM_RXRTSE 0x08 96 #define UARTMODEM_TXRTSPOL 0x04 97 #define UARTMODEM_TXRTSE 0x02 98 #define UARTMODEM_TXCTSE 0x01 99 100 #define UARTPFIFO_TXFE 0x80 101 #define UARTPFIFO_FIFOSIZE_MASK 0x7 102 #define UARTPFIFO_TXSIZE_OFF 4 103 #define UARTPFIFO_RXFE 0x08 104 #define UARTPFIFO_RXSIZE_OFF 0 105 106 #define UARTCFIFO_TXFLUSH 0x80 107 #define UARTCFIFO_RXFLUSH 0x40 108 #define UARTCFIFO_RXOFE 0x04 109 #define UARTCFIFO_TXOFE 0x02 110 #define UARTCFIFO_RXUFE 0x01 111 112 #define UARTSFIFO_TXEMPT 0x80 113 #define UARTSFIFO_RXEMPT 0x40 114 #define UARTSFIFO_RXOF 0x04 115 #define UARTSFIFO_TXOF 0x02 116 #define UARTSFIFO_RXUF 0x01 117 118 /* 32-bit global registers only for i.MX7ULP/i.MX8x 119 * Used to reset all internal logic and registers, except the Global Register. 120 */ 121 #define UART_GLOBAL 0x8 122 123 /* 32-bit register definition */ 124 #define UARTBAUD 0x00 125 #define UARTSTAT 0x04 126 #define UARTCTRL 0x08 127 #define UARTDATA 0x0C 128 #define UARTMATCH 0x10 129 #define UARTMODIR 0x14 130 #define UARTFIFO 0x18 131 #define UARTWATER 0x1c 132 133 #define UARTBAUD_MAEN1 0x80000000 134 #define UARTBAUD_MAEN2 0x40000000 135 #define UARTBAUD_M10 0x20000000 136 #define UARTBAUD_TDMAE 0x00800000 137 #define UARTBAUD_RDMAE 0x00200000 138 #define UARTBAUD_MATCFG 0x00400000 139 #define UARTBAUD_BOTHEDGE 0x00020000 140 #define UARTBAUD_RESYNCDIS 0x00010000 141 #define UARTBAUD_LBKDIE 0x00008000 142 #define UARTBAUD_RXEDGIE 0x00004000 143 #define UARTBAUD_SBNS 0x00002000 144 #define UARTBAUD_SBR 0x00000000 145 #define UARTBAUD_SBR_MASK 0x1fff 146 #define UARTBAUD_OSR_MASK 0x1f 147 #define UARTBAUD_OSR_SHIFT 24 148 149 #define UARTSTAT_LBKDIF 0x80000000 150 #define UARTSTAT_RXEDGIF 0x40000000 151 #define UARTSTAT_MSBF 0x20000000 152 #define UARTSTAT_RXINV 0x10000000 153 #define UARTSTAT_RWUID 0x08000000 154 #define UARTSTAT_BRK13 0x04000000 155 #define UARTSTAT_LBKDE 0x02000000 156 #define UARTSTAT_RAF 0x01000000 157 #define UARTSTAT_TDRE 0x00800000 158 #define UARTSTAT_TC 0x00400000 159 #define UARTSTAT_RDRF 0x00200000 160 #define UARTSTAT_IDLE 0x00100000 161 #define UARTSTAT_OR 0x00080000 162 #define UARTSTAT_NF 0x00040000 163 #define UARTSTAT_FE 0x00020000 164 #define UARTSTAT_PE 0x00010000 165 #define UARTSTAT_MA1F 0x00008000 166 #define UARTSTAT_M21F 0x00004000 167 168 #define UARTCTRL_R8T9 0x80000000 169 #define UARTCTRL_R9T8 0x40000000 170 #define UARTCTRL_TXDIR 0x20000000 171 #define UARTCTRL_TXINV 0x10000000 172 #define UARTCTRL_ORIE 0x08000000 173 #define UARTCTRL_NEIE 0x04000000 174 #define UARTCTRL_FEIE 0x02000000 175 #define UARTCTRL_PEIE 0x01000000 176 #define UARTCTRL_TIE 0x00800000 177 #define UARTCTRL_TCIE 0x00400000 178 #define UARTCTRL_RIE 0x00200000 179 #define UARTCTRL_ILIE 0x00100000 180 #define UARTCTRL_TE 0x00080000 181 #define UARTCTRL_RE 0x00040000 182 #define UARTCTRL_RWU 0x00020000 183 #define UARTCTRL_SBK 0x00010000 184 #define UARTCTRL_MA1IE 0x00008000 185 #define UARTCTRL_MA2IE 0x00004000 186 #define UARTCTRL_IDLECFG GENMASK(10, 8) 187 #define UARTCTRL_LOOPS 0x00000080 188 #define UARTCTRL_DOZEEN 0x00000040 189 #define UARTCTRL_RSRC 0x00000020 190 #define UARTCTRL_M 0x00000010 191 #define UARTCTRL_WAKE 0x00000008 192 #define UARTCTRL_ILT 0x00000004 193 #define UARTCTRL_PE 0x00000002 194 #define UARTCTRL_PT 0x00000001 195 196 #define UARTDATA_NOISY 0x00008000 197 #define UARTDATA_PARITYE 0x00004000 198 #define UARTDATA_FRETSC 0x00002000 199 #define UARTDATA_RXEMPT 0x00001000 200 #define UARTDATA_IDLINE 0x00000800 201 #define UARTDATA_MASK 0x3ff 202 203 #define UARTMODIR_IREN 0x00020000 204 #define UARTMODIR_RTSWATER GENMASK(10, 8) 205 #define UARTMODIR_TXCTSSRC 0x00000020 206 #define UARTMODIR_TXCTSC 0x00000010 207 #define UARTMODIR_RXRTSE 0x00000008 208 #define UARTMODIR_TXRTSPOL 0x00000004 209 #define UARTMODIR_TXRTSE 0x00000002 210 #define UARTMODIR_TXCTSE 0x00000001 211 212 #define UARTFIFO_TXEMPT 0x00800000 213 #define UARTFIFO_RXEMPT 0x00400000 214 #define UARTFIFO_TXOF 0x00020000 215 #define UARTFIFO_RXUF 0x00010000 216 #define UARTFIFO_TXFLUSH 0x00008000 217 #define UARTFIFO_RXFLUSH 0x00004000 218 #define UARTFIFO_RXIDEN GENMASK(12, 10) 219 #define UARTFIFO_TXOFE 0x00000200 220 #define UARTFIFO_RXUFE 0x00000100 221 #define UARTFIFO_TXFE 0x00000080 222 #define UARTFIFO_FIFOSIZE_MASK 0x7 223 #define UARTFIFO_TXSIZE_OFF 4 224 #define UARTFIFO_RXFE 0x00000008 225 #define UARTFIFO_RXSIZE_OFF 0 226 #define UARTFIFO_DEPTH(x) (0x1 << ((x) ? ((x) + 1) : 0)) 227 228 #define UARTWATER_COUNT_MASK 0xff 229 #define UARTWATER_TXCNT_OFF 8 230 #define UARTWATER_RXCNT_OFF 24 231 #define UARTWATER_WATER_MASK 0xff 232 #define UARTWATER_TXWATER_OFF 0 233 #define UARTWATER_RXWATER_OFF 16 234 235 #define UART_GLOBAL_RST 0x2 236 #define GLOBAL_RST_MIN_US 20 237 #define GLOBAL_RST_MAX_US 40 238 239 /* Rx DMA timeout in ms, which is used to calculate Rx ring buffer size */ 240 #define DMA_RX_TIMEOUT (10) 241 #define DMA_RX_IDLE_CHARS 8 242 #define UART_AUTOSUSPEND_TIMEOUT 3000 243 244 #define DRIVER_NAME "fsl-lpuart" 245 #define DEV_NAME "ttyLP" 246 #define UART_NR 8 247 248 /* IMX lpuart has four extra unused regs located at the beginning */ 249 #define IMX_REG_OFF 0x10 250 251 enum lpuart_type { 252 VF610_LPUART, 253 LS1021A_LPUART, 254 LS1028A_LPUART, 255 IMX7ULP_LPUART, 256 IMX8ULP_LPUART, 257 IMX8QXP_LPUART, 258 IMXRT1050_LPUART, 259 }; 260 261 struct lpuart_port { 262 struct uart_port port; 263 enum lpuart_type devtype; 264 struct clk *ipg_clk; 265 struct clk *baud_clk; 266 unsigned int txfifo_size; 267 unsigned int rxfifo_size; 268 269 u8 rx_watermark; 270 bool lpuart_dma_tx_use; 271 bool lpuart_dma_rx_use; 272 struct dma_chan *dma_tx_chan; 273 struct dma_chan *dma_rx_chan; 274 struct dma_async_tx_descriptor *dma_tx_desc; 275 struct dma_async_tx_descriptor *dma_rx_desc; 276 dma_cookie_t dma_tx_cookie; 277 dma_cookie_t dma_rx_cookie; 278 unsigned int dma_tx_bytes; 279 unsigned int dma_rx_bytes; 280 bool dma_tx_in_progress; 281 unsigned int dma_rx_timeout; 282 struct timer_list lpuart_timer; 283 struct scatterlist rx_sgl, tx_sgl[2]; 284 struct circ_buf rx_ring; 285 int rx_dma_rng_buf_len; 286 int last_residue; 287 unsigned int dma_tx_nents; 288 wait_queue_head_t dma_wait; 289 bool is_cs7; /* Set to true when character size is 7 */ 290 /* and the parity is enabled */ 291 bool dma_idle_int; 292 }; 293 294 struct lpuart_soc_data { 295 enum lpuart_type devtype; 296 char iotype; 297 u8 reg_off; 298 u8 rx_watermark; 299 }; 300 301 static const struct lpuart_soc_data vf_data = { 302 .devtype = VF610_LPUART, 303 .iotype = UPIO_MEM, 304 .rx_watermark = 1, 305 }; 306 307 static const struct lpuart_soc_data ls1021a_data = { 308 .devtype = LS1021A_LPUART, 309 .iotype = UPIO_MEM32BE, 310 .rx_watermark = 1, 311 }; 312 313 static const struct lpuart_soc_data ls1028a_data = { 314 .devtype = LS1028A_LPUART, 315 .iotype = UPIO_MEM32, 316 .rx_watermark = 0, 317 }; 318 319 static struct lpuart_soc_data imx7ulp_data = { 320 .devtype = IMX7ULP_LPUART, 321 .iotype = UPIO_MEM32, 322 .reg_off = IMX_REG_OFF, 323 .rx_watermark = 1, 324 }; 325 326 static struct lpuart_soc_data imx8ulp_data = { 327 .devtype = IMX8ULP_LPUART, 328 .iotype = UPIO_MEM32, 329 .reg_off = IMX_REG_OFF, 330 .rx_watermark = 3, 331 }; 332 333 static struct lpuart_soc_data imx8qxp_data = { 334 .devtype = IMX8QXP_LPUART, 335 .iotype = UPIO_MEM32, 336 .reg_off = IMX_REG_OFF, 337 .rx_watermark = 7, /* A lower watermark is ideal for low baud rates. */ 338 }; 339 static struct lpuart_soc_data imxrt1050_data = { 340 .devtype = IMXRT1050_LPUART, 341 .iotype = UPIO_MEM32, 342 .reg_off = IMX_REG_OFF, 343 .rx_watermark = 1, 344 }; 345 346 static const struct of_device_id lpuart_dt_ids[] = { 347 { .compatible = "fsl,vf610-lpuart", .data = &vf_data, }, 348 { .compatible = "fsl,ls1021a-lpuart", .data = &ls1021a_data, }, 349 { .compatible = "fsl,ls1028a-lpuart", .data = &ls1028a_data, }, 350 { .compatible = "fsl,imx7ulp-lpuart", .data = &imx7ulp_data, }, 351 { .compatible = "fsl,imx8ulp-lpuart", .data = &imx8ulp_data, }, 352 { .compatible = "fsl,imx8qxp-lpuart", .data = &imx8qxp_data, }, 353 { .compatible = "fsl,imxrt1050-lpuart", .data = &imxrt1050_data}, 354 { /* sentinel */ } 355 }; 356 MODULE_DEVICE_TABLE(of, lpuart_dt_ids); 357 358 /* Forward declare this for the dma callbacks*/ 359 static void lpuart_dma_tx_complete(void *arg); 360 361 static inline bool is_layerscape_lpuart(struct lpuart_port *sport) 362 { 363 return (sport->devtype == LS1021A_LPUART || 364 sport->devtype == LS1028A_LPUART); 365 } 366 367 static inline bool is_imx7ulp_lpuart(struct lpuart_port *sport) 368 { 369 return sport->devtype == IMX7ULP_LPUART; 370 } 371 372 static inline bool is_imx8ulp_lpuart(struct lpuart_port *sport) 373 { 374 return sport->devtype == IMX8ULP_LPUART; 375 } 376 377 static inline bool is_imx8qxp_lpuart(struct lpuart_port *sport) 378 { 379 return sport->devtype == IMX8QXP_LPUART; 380 } 381 382 static inline u32 lpuart32_read(struct uart_port *port, u32 off) 383 { 384 switch (port->iotype) { 385 case UPIO_MEM32: 386 return readl(port->membase + off); 387 case UPIO_MEM32BE: 388 return ioread32be(port->membase + off); 389 default: 390 return 0; 391 } 392 } 393 394 static inline void lpuart32_write(struct uart_port *port, u32 val, 395 u32 off) 396 { 397 switch (port->iotype) { 398 case UPIO_MEM32: 399 writel(val, port->membase + off); 400 break; 401 case UPIO_MEM32BE: 402 iowrite32be(val, port->membase + off); 403 break; 404 } 405 } 406 407 static int __lpuart_enable_clks(struct lpuart_port *sport, bool is_en) 408 { 409 int ret = 0; 410 411 if (is_en) { 412 ret = clk_prepare_enable(sport->ipg_clk); 413 if (ret) 414 return ret; 415 416 ret = clk_prepare_enable(sport->baud_clk); 417 if (ret) { 418 clk_disable_unprepare(sport->ipg_clk); 419 return ret; 420 } 421 } else { 422 clk_disable_unprepare(sport->baud_clk); 423 clk_disable_unprepare(sport->ipg_clk); 424 } 425 426 return 0; 427 } 428 429 static unsigned int lpuart_get_baud_clk_rate(struct lpuart_port *sport) 430 { 431 if (is_imx8qxp_lpuart(sport)) 432 return clk_get_rate(sport->baud_clk); 433 434 return clk_get_rate(sport->ipg_clk); 435 } 436 437 #define lpuart_enable_clks(x) __lpuart_enable_clks(x, true) 438 #define lpuart_disable_clks(x) __lpuart_enable_clks(x, false) 439 440 static void lpuart_stop_tx(struct uart_port *port) 441 { 442 unsigned char temp; 443 444 temp = readb(port->membase + UARTCR2); 445 temp &= ~(UARTCR2_TIE | UARTCR2_TCIE); 446 writeb(temp, port->membase + UARTCR2); 447 } 448 449 static void lpuart32_stop_tx(struct uart_port *port) 450 { 451 unsigned long temp; 452 453 temp = lpuart32_read(port, UARTCTRL); 454 temp &= ~(UARTCTRL_TIE | UARTCTRL_TCIE); 455 lpuart32_write(port, temp, UARTCTRL); 456 } 457 458 static void lpuart_stop_rx(struct uart_port *port) 459 { 460 unsigned char temp; 461 462 temp = readb(port->membase + UARTCR2); 463 writeb(temp & ~UARTCR2_RE, port->membase + UARTCR2); 464 } 465 466 static void lpuart32_stop_rx(struct uart_port *port) 467 { 468 unsigned long temp; 469 470 temp = lpuart32_read(port, UARTCTRL); 471 lpuart32_write(port, temp & ~UARTCTRL_RE, UARTCTRL); 472 } 473 474 static void lpuart_dma_tx(struct lpuart_port *sport) 475 { 476 struct circ_buf *xmit = &sport->port.state->xmit; 477 struct scatterlist *sgl = sport->tx_sgl; 478 struct device *dev = sport->port.dev; 479 struct dma_chan *chan = sport->dma_tx_chan; 480 int ret; 481 482 if (sport->dma_tx_in_progress) 483 return; 484 485 sport->dma_tx_bytes = uart_circ_chars_pending(xmit); 486 487 if (xmit->tail < xmit->head || xmit->head == 0) { 488 sport->dma_tx_nents = 1; 489 sg_init_one(sgl, xmit->buf + xmit->tail, sport->dma_tx_bytes); 490 } else { 491 sport->dma_tx_nents = 2; 492 sg_init_table(sgl, 2); 493 sg_set_buf(sgl, xmit->buf + xmit->tail, 494 UART_XMIT_SIZE - xmit->tail); 495 sg_set_buf(sgl + 1, xmit->buf, xmit->head); 496 } 497 498 ret = dma_map_sg(chan->device->dev, sgl, sport->dma_tx_nents, 499 DMA_TO_DEVICE); 500 if (!ret) { 501 dev_err(dev, "DMA mapping error for TX.\n"); 502 return; 503 } 504 505 sport->dma_tx_desc = dmaengine_prep_slave_sg(chan, sgl, 506 ret, DMA_MEM_TO_DEV, 507 DMA_PREP_INTERRUPT); 508 if (!sport->dma_tx_desc) { 509 dma_unmap_sg(chan->device->dev, sgl, sport->dma_tx_nents, 510 DMA_TO_DEVICE); 511 dev_err(dev, "Cannot prepare TX slave DMA!\n"); 512 return; 513 } 514 515 sport->dma_tx_desc->callback = lpuart_dma_tx_complete; 516 sport->dma_tx_desc->callback_param = sport; 517 sport->dma_tx_in_progress = true; 518 sport->dma_tx_cookie = dmaengine_submit(sport->dma_tx_desc); 519 dma_async_issue_pending(chan); 520 } 521 522 static bool lpuart_stopped_or_empty(struct uart_port *port) 523 { 524 return uart_circ_empty(&port->state->xmit) || uart_tx_stopped(port); 525 } 526 527 static void lpuart_dma_tx_complete(void *arg) 528 { 529 struct lpuart_port *sport = arg; 530 struct scatterlist *sgl = &sport->tx_sgl[0]; 531 struct circ_buf *xmit = &sport->port.state->xmit; 532 struct dma_chan *chan = sport->dma_tx_chan; 533 unsigned long flags; 534 535 uart_port_lock_irqsave(&sport->port, &flags); 536 if (!sport->dma_tx_in_progress) { 537 uart_port_unlock_irqrestore(&sport->port, flags); 538 return; 539 } 540 541 dma_unmap_sg(chan->device->dev, sgl, sport->dma_tx_nents, 542 DMA_TO_DEVICE); 543 544 uart_xmit_advance(&sport->port, sport->dma_tx_bytes); 545 sport->dma_tx_in_progress = false; 546 uart_port_unlock_irqrestore(&sport->port, flags); 547 548 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 549 uart_write_wakeup(&sport->port); 550 551 if (waitqueue_active(&sport->dma_wait)) { 552 wake_up(&sport->dma_wait); 553 return; 554 } 555 556 uart_port_lock_irqsave(&sport->port, &flags); 557 558 if (!lpuart_stopped_or_empty(&sport->port)) 559 lpuart_dma_tx(sport); 560 561 uart_port_unlock_irqrestore(&sport->port, flags); 562 } 563 564 static dma_addr_t lpuart_dma_datareg_addr(struct lpuart_port *sport) 565 { 566 switch (sport->port.iotype) { 567 case UPIO_MEM32: 568 return sport->port.mapbase + UARTDATA; 569 case UPIO_MEM32BE: 570 return sport->port.mapbase + UARTDATA + sizeof(u32) - 1; 571 } 572 return sport->port.mapbase + UARTDR; 573 } 574 575 static int lpuart_dma_tx_request(struct uart_port *port) 576 { 577 struct lpuart_port *sport = container_of(port, 578 struct lpuart_port, port); 579 struct dma_slave_config dma_tx_sconfig = {}; 580 int ret; 581 582 dma_tx_sconfig.dst_addr = lpuart_dma_datareg_addr(sport); 583 dma_tx_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 584 dma_tx_sconfig.dst_maxburst = 1; 585 dma_tx_sconfig.direction = DMA_MEM_TO_DEV; 586 ret = dmaengine_slave_config(sport->dma_tx_chan, &dma_tx_sconfig); 587 588 if (ret) { 589 dev_err(sport->port.dev, 590 "DMA slave config failed, err = %d\n", ret); 591 return ret; 592 } 593 594 return 0; 595 } 596 597 static bool lpuart_is_32(struct lpuart_port *sport) 598 { 599 return sport->port.iotype == UPIO_MEM32 || 600 sport->port.iotype == UPIO_MEM32BE; 601 } 602 603 static void lpuart_flush_buffer(struct uart_port *port) 604 { 605 struct lpuart_port *sport = container_of(port, struct lpuart_port, port); 606 struct dma_chan *chan = sport->dma_tx_chan; 607 u32 val; 608 609 if (sport->lpuart_dma_tx_use) { 610 if (sport->dma_tx_in_progress) { 611 dma_unmap_sg(chan->device->dev, &sport->tx_sgl[0], 612 sport->dma_tx_nents, DMA_TO_DEVICE); 613 sport->dma_tx_in_progress = false; 614 } 615 dmaengine_terminate_async(chan); 616 } 617 618 if (lpuart_is_32(sport)) { 619 val = lpuart32_read(&sport->port, UARTFIFO); 620 val |= UARTFIFO_TXFLUSH | UARTFIFO_RXFLUSH; 621 lpuart32_write(&sport->port, val, UARTFIFO); 622 } else { 623 val = readb(sport->port.membase + UARTCFIFO); 624 val |= UARTCFIFO_TXFLUSH | UARTCFIFO_RXFLUSH; 625 writeb(val, sport->port.membase + UARTCFIFO); 626 } 627 } 628 629 static void lpuart_wait_bit_set(struct uart_port *port, unsigned int offset, 630 u8 bit) 631 { 632 while (!(readb(port->membase + offset) & bit)) 633 cpu_relax(); 634 } 635 636 static void lpuart32_wait_bit_set(struct uart_port *port, unsigned int offset, 637 u32 bit) 638 { 639 while (!(lpuart32_read(port, offset) & bit)) 640 cpu_relax(); 641 } 642 643 #if defined(CONFIG_CONSOLE_POLL) 644 645 static int lpuart_poll_init(struct uart_port *port) 646 { 647 struct lpuart_port *sport = container_of(port, 648 struct lpuart_port, port); 649 unsigned long flags; 650 unsigned char temp; 651 652 sport->port.fifosize = 0; 653 654 uart_port_lock_irqsave(&sport->port, &flags); 655 /* Disable Rx & Tx */ 656 writeb(0, sport->port.membase + UARTCR2); 657 658 temp = readb(sport->port.membase + UARTPFIFO); 659 /* Enable Rx and Tx FIFO */ 660 writeb(temp | UARTPFIFO_RXFE | UARTPFIFO_TXFE, 661 sport->port.membase + UARTPFIFO); 662 663 /* flush Tx and Rx FIFO */ 664 writeb(UARTCFIFO_TXFLUSH | UARTCFIFO_RXFLUSH, 665 sport->port.membase + UARTCFIFO); 666 667 /* explicitly clear RDRF */ 668 if (readb(sport->port.membase + UARTSR1) & UARTSR1_RDRF) { 669 readb(sport->port.membase + UARTDR); 670 writeb(UARTSFIFO_RXUF, sport->port.membase + UARTSFIFO); 671 } 672 673 writeb(0, sport->port.membase + UARTTWFIFO); 674 writeb(1, sport->port.membase + UARTRWFIFO); 675 676 /* Enable Rx and Tx */ 677 writeb(UARTCR2_RE | UARTCR2_TE, sport->port.membase + UARTCR2); 678 uart_port_unlock_irqrestore(&sport->port, flags); 679 680 return 0; 681 } 682 683 static void lpuart_poll_put_char(struct uart_port *port, unsigned char c) 684 { 685 /* drain */ 686 lpuart_wait_bit_set(port, UARTSR1, UARTSR1_TDRE); 687 writeb(c, port->membase + UARTDR); 688 } 689 690 static int lpuart_poll_get_char(struct uart_port *port) 691 { 692 if (!(readb(port->membase + UARTSR1) & UARTSR1_RDRF)) 693 return NO_POLL_CHAR; 694 695 return readb(port->membase + UARTDR); 696 } 697 698 static int lpuart32_poll_init(struct uart_port *port) 699 { 700 unsigned long flags; 701 struct lpuart_port *sport = container_of(port, struct lpuart_port, port); 702 u32 temp; 703 704 sport->port.fifosize = 0; 705 706 uart_port_lock_irqsave(&sport->port, &flags); 707 708 /* Disable Rx & Tx */ 709 lpuart32_write(&sport->port, 0, UARTCTRL); 710 711 temp = lpuart32_read(&sport->port, UARTFIFO); 712 713 /* Enable Rx and Tx FIFO */ 714 lpuart32_write(&sport->port, temp | UARTFIFO_RXFE | UARTFIFO_TXFE, UARTFIFO); 715 716 /* flush Tx and Rx FIFO */ 717 lpuart32_write(&sport->port, UARTFIFO_TXFLUSH | UARTFIFO_RXFLUSH, UARTFIFO); 718 719 /* explicitly clear RDRF */ 720 if (lpuart32_read(&sport->port, UARTSTAT) & UARTSTAT_RDRF) { 721 lpuart32_read(&sport->port, UARTDATA); 722 lpuart32_write(&sport->port, UARTFIFO_RXUF, UARTFIFO); 723 } 724 725 /* Enable Rx and Tx */ 726 lpuart32_write(&sport->port, UARTCTRL_RE | UARTCTRL_TE, UARTCTRL); 727 uart_port_unlock_irqrestore(&sport->port, flags); 728 729 return 0; 730 } 731 732 static void lpuart32_poll_put_char(struct uart_port *port, unsigned char c) 733 { 734 lpuart32_wait_bit_set(port, UARTSTAT, UARTSTAT_TDRE); 735 lpuart32_write(port, c, UARTDATA); 736 } 737 738 static int lpuart32_poll_get_char(struct uart_port *port) 739 { 740 if (!(lpuart32_read(port, UARTWATER) >> UARTWATER_RXCNT_OFF)) 741 return NO_POLL_CHAR; 742 743 return lpuart32_read(port, UARTDATA); 744 } 745 #endif 746 747 static inline void lpuart_transmit_buffer(struct lpuart_port *sport) 748 { 749 struct uart_port *port = &sport->port; 750 u8 ch; 751 752 uart_port_tx(port, ch, 753 readb(port->membase + UARTTCFIFO) < sport->txfifo_size, 754 writeb(ch, port->membase + UARTDR)); 755 } 756 757 static inline void lpuart32_transmit_buffer(struct lpuart_port *sport) 758 { 759 struct circ_buf *xmit = &sport->port.state->xmit; 760 unsigned long txcnt; 761 762 if (sport->port.x_char) { 763 lpuart32_write(&sport->port, sport->port.x_char, UARTDATA); 764 sport->port.icount.tx++; 765 sport->port.x_char = 0; 766 return; 767 } 768 769 if (lpuart_stopped_or_empty(&sport->port)) { 770 lpuart32_stop_tx(&sport->port); 771 return; 772 } 773 774 txcnt = lpuart32_read(&sport->port, UARTWATER); 775 txcnt = txcnt >> UARTWATER_TXCNT_OFF; 776 txcnt &= UARTWATER_COUNT_MASK; 777 while (!uart_circ_empty(xmit) && (txcnt < sport->txfifo_size)) { 778 lpuart32_write(&sport->port, xmit->buf[xmit->tail], UARTDATA); 779 uart_xmit_advance(&sport->port, 1); 780 txcnt = lpuart32_read(&sport->port, UARTWATER); 781 txcnt = txcnt >> UARTWATER_TXCNT_OFF; 782 txcnt &= UARTWATER_COUNT_MASK; 783 } 784 785 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 786 uart_write_wakeup(&sport->port); 787 788 if (uart_circ_empty(xmit)) 789 lpuart32_stop_tx(&sport->port); 790 } 791 792 static void lpuart_start_tx(struct uart_port *port) 793 { 794 struct lpuart_port *sport = container_of(port, 795 struct lpuart_port, port); 796 unsigned char temp; 797 798 temp = readb(port->membase + UARTCR2); 799 writeb(temp | UARTCR2_TIE, port->membase + UARTCR2); 800 801 if (sport->lpuart_dma_tx_use) { 802 if (!lpuart_stopped_or_empty(port)) 803 lpuart_dma_tx(sport); 804 } else { 805 if (readb(port->membase + UARTSR1) & UARTSR1_TDRE) 806 lpuart_transmit_buffer(sport); 807 } 808 } 809 810 static void lpuart32_start_tx(struct uart_port *port) 811 { 812 struct lpuart_port *sport = container_of(port, struct lpuart_port, port); 813 unsigned long temp; 814 815 if (sport->lpuart_dma_tx_use) { 816 if (!lpuart_stopped_or_empty(port)) 817 lpuart_dma_tx(sport); 818 } else { 819 temp = lpuart32_read(port, UARTCTRL); 820 lpuart32_write(port, temp | UARTCTRL_TIE, UARTCTRL); 821 822 if (lpuart32_read(port, UARTSTAT) & UARTSTAT_TDRE) 823 lpuart32_transmit_buffer(sport); 824 } 825 } 826 827 static void 828 lpuart_uart_pm(struct uart_port *port, unsigned int state, unsigned int oldstate) 829 { 830 switch (state) { 831 case UART_PM_STATE_OFF: 832 pm_runtime_mark_last_busy(port->dev); 833 pm_runtime_put_autosuspend(port->dev); 834 break; 835 default: 836 pm_runtime_get_sync(port->dev); 837 break; 838 } 839 } 840 841 /* return TIOCSER_TEMT when transmitter is not busy */ 842 static unsigned int lpuart_tx_empty(struct uart_port *port) 843 { 844 struct lpuart_port *sport = container_of(port, 845 struct lpuart_port, port); 846 unsigned char sr1 = readb(port->membase + UARTSR1); 847 unsigned char sfifo = readb(port->membase + UARTSFIFO); 848 849 if (sport->dma_tx_in_progress) 850 return 0; 851 852 if (sr1 & UARTSR1_TC && sfifo & UARTSFIFO_TXEMPT) 853 return TIOCSER_TEMT; 854 855 return 0; 856 } 857 858 static unsigned int lpuart32_tx_empty(struct uart_port *port) 859 { 860 struct lpuart_port *sport = container_of(port, 861 struct lpuart_port, port); 862 unsigned long stat = lpuart32_read(port, UARTSTAT); 863 unsigned long sfifo = lpuart32_read(port, UARTFIFO); 864 unsigned long ctrl = lpuart32_read(port, UARTCTRL); 865 866 if (sport->dma_tx_in_progress) 867 return 0; 868 869 /* 870 * LPUART Transmission Complete Flag may never be set while queuing a break 871 * character, so avoid checking for transmission complete when UARTCTRL_SBK 872 * is asserted. 873 */ 874 if ((stat & UARTSTAT_TC && sfifo & UARTFIFO_TXEMPT) || ctrl & UARTCTRL_SBK) 875 return TIOCSER_TEMT; 876 877 return 0; 878 } 879 880 static void lpuart_txint(struct lpuart_port *sport) 881 { 882 uart_port_lock(&sport->port); 883 lpuart_transmit_buffer(sport); 884 uart_port_unlock(&sport->port); 885 } 886 887 static void lpuart_rxint(struct lpuart_port *sport) 888 { 889 unsigned int flg, ignored = 0, overrun = 0; 890 struct tty_port *port = &sport->port.state->port; 891 unsigned char rx, sr; 892 893 uart_port_lock(&sport->port); 894 895 while (!(readb(sport->port.membase + UARTSFIFO) & UARTSFIFO_RXEMPT)) { 896 flg = TTY_NORMAL; 897 sport->port.icount.rx++; 898 /* 899 * to clear the FE, OR, NF, FE, PE flags, 900 * read SR1 then read DR 901 */ 902 sr = readb(sport->port.membase + UARTSR1); 903 rx = readb(sport->port.membase + UARTDR); 904 905 if (uart_prepare_sysrq_char(&sport->port, rx)) 906 continue; 907 908 if (sr & (UARTSR1_PE | UARTSR1_OR | UARTSR1_FE)) { 909 if (sr & UARTSR1_PE) 910 sport->port.icount.parity++; 911 else if (sr & UARTSR1_FE) 912 sport->port.icount.frame++; 913 914 if (sr & UARTSR1_OR) 915 overrun++; 916 917 if (sr & sport->port.ignore_status_mask) { 918 if (++ignored > 100) 919 goto out; 920 continue; 921 } 922 923 sr &= sport->port.read_status_mask; 924 925 if (sr & UARTSR1_PE) 926 flg = TTY_PARITY; 927 else if (sr & UARTSR1_FE) 928 flg = TTY_FRAME; 929 930 if (sr & UARTSR1_OR) 931 flg = TTY_OVERRUN; 932 933 sport->port.sysrq = 0; 934 } 935 936 if (tty_insert_flip_char(port, rx, flg) == 0) 937 sport->port.icount.buf_overrun++; 938 } 939 940 out: 941 if (overrun) { 942 sport->port.icount.overrun += overrun; 943 944 /* 945 * Overruns cause FIFO pointers to become missaligned. 946 * Flushing the receive FIFO reinitializes the pointers. 947 */ 948 writeb(UARTCFIFO_RXFLUSH, sport->port.membase + UARTCFIFO); 949 writeb(UARTSFIFO_RXOF, sport->port.membase + UARTSFIFO); 950 } 951 952 uart_unlock_and_check_sysrq(&sport->port); 953 954 tty_flip_buffer_push(port); 955 } 956 957 static void lpuart32_txint(struct lpuart_port *sport) 958 { 959 uart_port_lock(&sport->port); 960 lpuart32_transmit_buffer(sport); 961 uart_port_unlock(&sport->port); 962 } 963 964 static void lpuart32_rxint(struct lpuart_port *sport) 965 { 966 unsigned int flg, ignored = 0; 967 struct tty_port *port = &sport->port.state->port; 968 unsigned long rx, sr; 969 bool is_break; 970 971 uart_port_lock(&sport->port); 972 973 while (!(lpuart32_read(&sport->port, UARTFIFO) & UARTFIFO_RXEMPT)) { 974 flg = TTY_NORMAL; 975 sport->port.icount.rx++; 976 /* 977 * to clear the FE, OR, NF, FE, PE flags, 978 * read STAT then read DATA reg 979 */ 980 sr = lpuart32_read(&sport->port, UARTSTAT); 981 rx = lpuart32_read(&sport->port, UARTDATA); 982 rx &= UARTDATA_MASK; 983 984 /* 985 * The LPUART can't distinguish between a break and a framing error, 986 * thus we assume it is a break if the received data is zero. 987 */ 988 is_break = (sr & UARTSTAT_FE) && !rx; 989 990 if (is_break && uart_handle_break(&sport->port)) 991 continue; 992 993 if (uart_prepare_sysrq_char(&sport->port, rx)) 994 continue; 995 996 if (sr & (UARTSTAT_PE | UARTSTAT_OR | UARTSTAT_FE)) { 997 if (sr & UARTSTAT_PE) { 998 sport->port.icount.parity++; 999 } else if (sr & UARTSTAT_FE) { 1000 if (is_break) 1001 sport->port.icount.brk++; 1002 else 1003 sport->port.icount.frame++; 1004 } 1005 1006 if (sr & UARTSTAT_OR) 1007 sport->port.icount.overrun++; 1008 1009 if (sr & sport->port.ignore_status_mask) { 1010 if (++ignored > 100) 1011 goto out; 1012 continue; 1013 } 1014 1015 sr &= sport->port.read_status_mask; 1016 1017 if (sr & UARTSTAT_PE) { 1018 flg = TTY_PARITY; 1019 } else if (sr & UARTSTAT_FE) { 1020 if (is_break) 1021 flg = TTY_BREAK; 1022 else 1023 flg = TTY_FRAME; 1024 } 1025 1026 if (sr & UARTSTAT_OR) 1027 flg = TTY_OVERRUN; 1028 } 1029 1030 if (sport->is_cs7) 1031 rx &= 0x7F; 1032 1033 if (tty_insert_flip_char(port, rx, flg) == 0) 1034 sport->port.icount.buf_overrun++; 1035 } 1036 1037 out: 1038 uart_unlock_and_check_sysrq(&sport->port); 1039 1040 tty_flip_buffer_push(port); 1041 } 1042 1043 static irqreturn_t lpuart_int(int irq, void *dev_id) 1044 { 1045 struct lpuart_port *sport = dev_id; 1046 unsigned char sts; 1047 1048 sts = readb(sport->port.membase + UARTSR1); 1049 1050 /* SysRq, using dma, check for linebreak by framing err. */ 1051 if (sts & UARTSR1_FE && sport->lpuart_dma_rx_use) { 1052 readb(sport->port.membase + UARTDR); 1053 uart_handle_break(&sport->port); 1054 /* linebreak produces some garbage, removing it */ 1055 writeb(UARTCFIFO_RXFLUSH, sport->port.membase + UARTCFIFO); 1056 return IRQ_HANDLED; 1057 } 1058 1059 if (sts & UARTSR1_RDRF && !sport->lpuart_dma_rx_use) 1060 lpuart_rxint(sport); 1061 1062 if (sts & UARTSR1_TDRE && !sport->lpuart_dma_tx_use) 1063 lpuart_txint(sport); 1064 1065 return IRQ_HANDLED; 1066 } 1067 1068 static inline void lpuart_handle_sysrq_chars(struct uart_port *port, 1069 unsigned char *p, int count) 1070 { 1071 while (count--) { 1072 if (*p && uart_handle_sysrq_char(port, *p)) 1073 return; 1074 p++; 1075 } 1076 } 1077 1078 static void lpuart_handle_sysrq(struct lpuart_port *sport) 1079 { 1080 struct circ_buf *ring = &sport->rx_ring; 1081 int count; 1082 1083 if (ring->head < ring->tail) { 1084 count = sport->rx_sgl.length - ring->tail; 1085 lpuart_handle_sysrq_chars(&sport->port, 1086 ring->buf + ring->tail, count); 1087 ring->tail = 0; 1088 } 1089 1090 if (ring->head > ring->tail) { 1091 count = ring->head - ring->tail; 1092 lpuart_handle_sysrq_chars(&sport->port, 1093 ring->buf + ring->tail, count); 1094 ring->tail = ring->head; 1095 } 1096 } 1097 1098 static int lpuart_tty_insert_flip_string(struct tty_port *port, 1099 unsigned char *chars, size_t size, bool is_cs7) 1100 { 1101 int i; 1102 1103 if (is_cs7) 1104 for (i = 0; i < size; i++) 1105 chars[i] &= 0x7F; 1106 return tty_insert_flip_string(port, chars, size); 1107 } 1108 1109 static void lpuart_copy_rx_to_tty(struct lpuart_port *sport) 1110 { 1111 struct tty_port *port = &sport->port.state->port; 1112 struct dma_tx_state state; 1113 enum dma_status dmastat; 1114 struct dma_chan *chan = sport->dma_rx_chan; 1115 struct circ_buf *ring = &sport->rx_ring; 1116 unsigned long flags; 1117 int count, copied; 1118 1119 if (lpuart_is_32(sport)) { 1120 unsigned long sr = lpuart32_read(&sport->port, UARTSTAT); 1121 1122 if (sr & (UARTSTAT_PE | UARTSTAT_FE)) { 1123 /* Clear the error flags */ 1124 lpuart32_write(&sport->port, sr, UARTSTAT); 1125 1126 if (sr & UARTSTAT_PE) 1127 sport->port.icount.parity++; 1128 else if (sr & UARTSTAT_FE) 1129 sport->port.icount.frame++; 1130 } 1131 } else { 1132 unsigned char sr = readb(sport->port.membase + UARTSR1); 1133 1134 if (sr & (UARTSR1_PE | UARTSR1_FE)) { 1135 unsigned char cr2; 1136 1137 /* Disable receiver during this operation... */ 1138 cr2 = readb(sport->port.membase + UARTCR2); 1139 cr2 &= ~UARTCR2_RE; 1140 writeb(cr2, sport->port.membase + UARTCR2); 1141 1142 /* Read DR to clear the error flags */ 1143 readb(sport->port.membase + UARTDR); 1144 1145 if (sr & UARTSR1_PE) 1146 sport->port.icount.parity++; 1147 else if (sr & UARTSR1_FE) 1148 sport->port.icount.frame++; 1149 /* 1150 * At this point parity/framing error is 1151 * cleared However, since the DMA already read 1152 * the data register and we had to read it 1153 * again after reading the status register to 1154 * properly clear the flags, the FIFO actually 1155 * underflowed... This requires a clearing of 1156 * the FIFO... 1157 */ 1158 if (readb(sport->port.membase + UARTSFIFO) & 1159 UARTSFIFO_RXUF) { 1160 writeb(UARTSFIFO_RXUF, 1161 sport->port.membase + UARTSFIFO); 1162 writeb(UARTCFIFO_RXFLUSH, 1163 sport->port.membase + UARTCFIFO); 1164 } 1165 1166 cr2 |= UARTCR2_RE; 1167 writeb(cr2, sport->port.membase + UARTCR2); 1168 } 1169 } 1170 1171 async_tx_ack(sport->dma_rx_desc); 1172 1173 uart_port_lock_irqsave(&sport->port, &flags); 1174 1175 dmastat = dmaengine_tx_status(chan, sport->dma_rx_cookie, &state); 1176 if (dmastat == DMA_ERROR) { 1177 dev_err(sport->port.dev, "Rx DMA transfer failed!\n"); 1178 uart_port_unlock_irqrestore(&sport->port, flags); 1179 return; 1180 } 1181 1182 /* CPU claims ownership of RX DMA buffer */ 1183 dma_sync_sg_for_cpu(chan->device->dev, &sport->rx_sgl, 1, 1184 DMA_FROM_DEVICE); 1185 1186 /* 1187 * ring->head points to the end of data already written by the DMA. 1188 * ring->tail points to the beginning of data to be read by the 1189 * framework. 1190 * The current transfer size should not be larger than the dma buffer 1191 * length. 1192 */ 1193 ring->head = sport->rx_sgl.length - state.residue; 1194 BUG_ON(ring->head > sport->rx_sgl.length); 1195 1196 /* 1197 * Silent handling of keys pressed in the sysrq timeframe 1198 */ 1199 if (sport->port.sysrq) { 1200 lpuart_handle_sysrq(sport); 1201 goto exit; 1202 } 1203 1204 /* 1205 * At this point ring->head may point to the first byte right after the 1206 * last byte of the dma buffer: 1207 * 0 <= ring->head <= sport->rx_sgl.length 1208 * 1209 * However ring->tail must always points inside the dma buffer: 1210 * 0 <= ring->tail <= sport->rx_sgl.length - 1 1211 * 1212 * Since we use a ring buffer, we have to handle the case 1213 * where head is lower than tail. In such a case, we first read from 1214 * tail to the end of the buffer then reset tail. 1215 */ 1216 if (ring->head < ring->tail) { 1217 count = sport->rx_sgl.length - ring->tail; 1218 1219 copied = lpuart_tty_insert_flip_string(port, ring->buf + ring->tail, 1220 count, sport->is_cs7); 1221 if (copied != count) 1222 sport->port.icount.buf_overrun++; 1223 ring->tail = 0; 1224 sport->port.icount.rx += copied; 1225 } 1226 1227 /* Finally we read data from tail to head */ 1228 if (ring->tail < ring->head) { 1229 count = ring->head - ring->tail; 1230 copied = lpuart_tty_insert_flip_string(port, ring->buf + ring->tail, 1231 count, sport->is_cs7); 1232 if (copied != count) 1233 sport->port.icount.buf_overrun++; 1234 /* Wrap ring->head if needed */ 1235 if (ring->head >= sport->rx_sgl.length) 1236 ring->head = 0; 1237 ring->tail = ring->head; 1238 sport->port.icount.rx += copied; 1239 } 1240 1241 sport->last_residue = state.residue; 1242 1243 exit: 1244 dma_sync_sg_for_device(chan->device->dev, &sport->rx_sgl, 1, 1245 DMA_FROM_DEVICE); 1246 1247 uart_port_unlock_irqrestore(&sport->port, flags); 1248 1249 tty_flip_buffer_push(port); 1250 if (!sport->dma_idle_int) 1251 mod_timer(&sport->lpuart_timer, jiffies + sport->dma_rx_timeout); 1252 } 1253 1254 static void lpuart_dma_rx_complete(void *arg) 1255 { 1256 struct lpuart_port *sport = arg; 1257 1258 lpuart_copy_rx_to_tty(sport); 1259 } 1260 1261 static void lpuart32_dma_idleint(struct lpuart_port *sport) 1262 { 1263 enum dma_status dmastat; 1264 struct dma_chan *chan = sport->dma_rx_chan; 1265 struct circ_buf *ring = &sport->rx_ring; 1266 struct dma_tx_state state; 1267 int count = 0; 1268 1269 dmastat = dmaengine_tx_status(chan, sport->dma_rx_cookie, &state); 1270 if (dmastat == DMA_ERROR) { 1271 dev_err(sport->port.dev, "Rx DMA transfer failed!\n"); 1272 return; 1273 } 1274 1275 ring->head = sport->rx_sgl.length - state.residue; 1276 count = CIRC_CNT(ring->head, ring->tail, sport->rx_sgl.length); 1277 1278 /* Check if new data received before copying */ 1279 if (count) 1280 lpuart_copy_rx_to_tty(sport); 1281 } 1282 1283 static irqreturn_t lpuart32_int(int irq, void *dev_id) 1284 { 1285 struct lpuart_port *sport = dev_id; 1286 unsigned long sts, rxcount; 1287 1288 sts = lpuart32_read(&sport->port, UARTSTAT); 1289 rxcount = lpuart32_read(&sport->port, UARTWATER); 1290 rxcount = rxcount >> UARTWATER_RXCNT_OFF; 1291 1292 if ((sts & UARTSTAT_RDRF || rxcount > 0) && !sport->lpuart_dma_rx_use) 1293 lpuart32_rxint(sport); 1294 1295 if ((sts & UARTSTAT_TDRE) && !sport->lpuart_dma_tx_use) 1296 lpuart32_txint(sport); 1297 1298 if ((sts & UARTSTAT_IDLE) && sport->lpuart_dma_rx_use && sport->dma_idle_int) 1299 lpuart32_dma_idleint(sport); 1300 1301 lpuart32_write(&sport->port, sts, UARTSTAT); 1302 return IRQ_HANDLED; 1303 } 1304 1305 /* 1306 * Timer function to simulate the hardware EOP (End Of Package) event. 1307 * The timer callback is to check for new RX data and copy to TTY buffer. 1308 * If no new data are received since last interval, the EOP condition is 1309 * met, complete the DMA transfer by copying the data. Otherwise, just 1310 * restart timer. 1311 */ 1312 static void lpuart_timer_func(struct timer_list *t) 1313 { 1314 struct lpuart_port *sport = from_timer(sport, t, lpuart_timer); 1315 enum dma_status dmastat; 1316 struct dma_chan *chan = sport->dma_rx_chan; 1317 struct circ_buf *ring = &sport->rx_ring; 1318 struct dma_tx_state state; 1319 unsigned long flags; 1320 int count; 1321 1322 dmastat = dmaengine_tx_status(chan, sport->dma_rx_cookie, &state); 1323 if (dmastat == DMA_ERROR) { 1324 dev_err(sport->port.dev, "Rx DMA transfer failed!\n"); 1325 return; 1326 } 1327 1328 ring->head = sport->rx_sgl.length - state.residue; 1329 count = CIRC_CNT(ring->head, ring->tail, sport->rx_sgl.length); 1330 1331 /* Check if new data received before copying */ 1332 if ((count != 0) && (sport->last_residue == state.residue)) 1333 lpuart_copy_rx_to_tty(sport); 1334 else 1335 mod_timer(&sport->lpuart_timer, 1336 jiffies + sport->dma_rx_timeout); 1337 1338 if (uart_port_trylock_irqsave(&sport->port, &flags)) { 1339 sport->last_residue = state.residue; 1340 uart_port_unlock_irqrestore(&sport->port, flags); 1341 } 1342 } 1343 1344 static inline int lpuart_start_rx_dma(struct lpuart_port *sport) 1345 { 1346 struct dma_slave_config dma_rx_sconfig = {}; 1347 struct circ_buf *ring = &sport->rx_ring; 1348 int ret, nent; 1349 struct tty_port *port = &sport->port.state->port; 1350 struct tty_struct *tty = port->tty; 1351 struct ktermios *termios = &tty->termios; 1352 struct dma_chan *chan = sport->dma_rx_chan; 1353 unsigned int bits = tty_get_frame_size(termios->c_cflag); 1354 unsigned int baud = tty_get_baud_rate(tty); 1355 1356 /* 1357 * Calculate length of one DMA buffer size to keep latency below 1358 * 10ms at any baud rate. 1359 */ 1360 sport->rx_dma_rng_buf_len = (DMA_RX_TIMEOUT * baud / bits / 1000) * 2; 1361 sport->rx_dma_rng_buf_len = (1 << fls(sport->rx_dma_rng_buf_len)); 1362 sport->rx_dma_rng_buf_len = max_t(int, 1363 sport->rxfifo_size * 2, 1364 sport->rx_dma_rng_buf_len); 1365 /* 1366 * Keep this condition check in case rxfifo_size is unavailable 1367 * for some SoCs. 1368 */ 1369 if (sport->rx_dma_rng_buf_len < 16) 1370 sport->rx_dma_rng_buf_len = 16; 1371 1372 sport->last_residue = 0; 1373 sport->dma_rx_timeout = max(nsecs_to_jiffies( 1374 sport->port.frame_time * DMA_RX_IDLE_CHARS), 1UL); 1375 1376 ring->buf = kzalloc(sport->rx_dma_rng_buf_len, GFP_ATOMIC); 1377 if (!ring->buf) 1378 return -ENOMEM; 1379 1380 sg_init_one(&sport->rx_sgl, ring->buf, sport->rx_dma_rng_buf_len); 1381 nent = dma_map_sg(chan->device->dev, &sport->rx_sgl, 1, 1382 DMA_FROM_DEVICE); 1383 1384 if (!nent) { 1385 dev_err(sport->port.dev, "DMA Rx mapping error\n"); 1386 return -EINVAL; 1387 } 1388 1389 dma_rx_sconfig.src_addr = lpuart_dma_datareg_addr(sport); 1390 dma_rx_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 1391 dma_rx_sconfig.src_maxburst = 1; 1392 dma_rx_sconfig.direction = DMA_DEV_TO_MEM; 1393 ret = dmaengine_slave_config(chan, &dma_rx_sconfig); 1394 1395 if (ret < 0) { 1396 dev_err(sport->port.dev, 1397 "DMA Rx slave config failed, err = %d\n", ret); 1398 return ret; 1399 } 1400 1401 sport->dma_rx_desc = dmaengine_prep_dma_cyclic(chan, 1402 sg_dma_address(&sport->rx_sgl), 1403 sport->rx_sgl.length, 1404 sport->rx_sgl.length / 2, 1405 DMA_DEV_TO_MEM, 1406 DMA_PREP_INTERRUPT); 1407 if (!sport->dma_rx_desc) { 1408 dev_err(sport->port.dev, "Cannot prepare cyclic DMA\n"); 1409 return -EFAULT; 1410 } 1411 1412 sport->dma_rx_desc->callback = lpuart_dma_rx_complete; 1413 sport->dma_rx_desc->callback_param = sport; 1414 sport->dma_rx_cookie = dmaengine_submit(sport->dma_rx_desc); 1415 dma_async_issue_pending(chan); 1416 1417 if (lpuart_is_32(sport)) { 1418 unsigned long temp = lpuart32_read(&sport->port, UARTBAUD); 1419 1420 lpuart32_write(&sport->port, temp | UARTBAUD_RDMAE, UARTBAUD); 1421 1422 if (sport->dma_idle_int) { 1423 unsigned long ctrl = lpuart32_read(&sport->port, UARTCTRL); 1424 1425 lpuart32_write(&sport->port, ctrl | UARTCTRL_ILIE, UARTCTRL); 1426 } 1427 } else { 1428 writeb(readb(sport->port.membase + UARTCR5) | UARTCR5_RDMAS, 1429 sport->port.membase + UARTCR5); 1430 } 1431 1432 return 0; 1433 } 1434 1435 static void lpuart_dma_rx_free(struct uart_port *port) 1436 { 1437 struct lpuart_port *sport = container_of(port, 1438 struct lpuart_port, port); 1439 struct dma_chan *chan = sport->dma_rx_chan; 1440 1441 dmaengine_terminate_sync(chan); 1442 if (!sport->dma_idle_int) 1443 del_timer_sync(&sport->lpuart_timer); 1444 1445 dma_unmap_sg(chan->device->dev, &sport->rx_sgl, 1, DMA_FROM_DEVICE); 1446 kfree(sport->rx_ring.buf); 1447 sport->rx_ring.tail = 0; 1448 sport->rx_ring.head = 0; 1449 sport->dma_rx_desc = NULL; 1450 sport->dma_rx_cookie = -EINVAL; 1451 } 1452 1453 static int lpuart_config_rs485(struct uart_port *port, struct ktermios *termios, 1454 struct serial_rs485 *rs485) 1455 { 1456 struct lpuart_port *sport = container_of(port, 1457 struct lpuart_port, port); 1458 1459 u8 modem = readb(sport->port.membase + UARTMODEM) & 1460 ~(UARTMODEM_TXRTSPOL | UARTMODEM_TXRTSE); 1461 writeb(modem, sport->port.membase + UARTMODEM); 1462 1463 if (rs485->flags & SER_RS485_ENABLED) { 1464 /* Enable auto RS-485 RTS mode */ 1465 modem |= UARTMODEM_TXRTSE; 1466 1467 /* 1468 * The hardware defaults to RTS logic HIGH while transfer. 1469 * Switch polarity in case RTS shall be logic HIGH 1470 * after transfer. 1471 * Note: UART is assumed to be active high. 1472 */ 1473 if (rs485->flags & SER_RS485_RTS_ON_SEND) 1474 modem |= UARTMODEM_TXRTSPOL; 1475 else if (rs485->flags & SER_RS485_RTS_AFTER_SEND) 1476 modem &= ~UARTMODEM_TXRTSPOL; 1477 } 1478 1479 writeb(modem, sport->port.membase + UARTMODEM); 1480 return 0; 1481 } 1482 1483 static int lpuart32_config_rs485(struct uart_port *port, struct ktermios *termios, 1484 struct serial_rs485 *rs485) 1485 { 1486 struct lpuart_port *sport = container_of(port, 1487 struct lpuart_port, port); 1488 1489 unsigned long modem = lpuart32_read(&sport->port, UARTMODIR) 1490 & ~(UARTMODIR_TXRTSPOL | UARTMODIR_TXRTSE); 1491 lpuart32_write(&sport->port, modem, UARTMODIR); 1492 1493 if (rs485->flags & SER_RS485_ENABLED) { 1494 /* Enable auto RS-485 RTS mode */ 1495 modem |= UARTMODIR_TXRTSE; 1496 1497 /* 1498 * The hardware defaults to RTS logic HIGH while transfer. 1499 * Switch polarity in case RTS shall be logic HIGH 1500 * after transfer. 1501 * Note: UART is assumed to be active high. 1502 */ 1503 if (rs485->flags & SER_RS485_RTS_ON_SEND) 1504 modem |= UARTMODIR_TXRTSPOL; 1505 else if (rs485->flags & SER_RS485_RTS_AFTER_SEND) 1506 modem &= ~UARTMODIR_TXRTSPOL; 1507 } 1508 1509 lpuart32_write(&sport->port, modem, UARTMODIR); 1510 return 0; 1511 } 1512 1513 static unsigned int lpuart_get_mctrl(struct uart_port *port) 1514 { 1515 unsigned int mctrl = 0; 1516 u8 reg; 1517 1518 reg = readb(port->membase + UARTCR1); 1519 if (reg & UARTCR1_LOOPS) 1520 mctrl |= TIOCM_LOOP; 1521 1522 return mctrl; 1523 } 1524 1525 static unsigned int lpuart32_get_mctrl(struct uart_port *port) 1526 { 1527 unsigned int mctrl = TIOCM_CAR | TIOCM_DSR | TIOCM_CTS; 1528 u32 reg; 1529 1530 reg = lpuart32_read(port, UARTCTRL); 1531 if (reg & UARTCTRL_LOOPS) 1532 mctrl |= TIOCM_LOOP; 1533 1534 return mctrl; 1535 } 1536 1537 static void lpuart_set_mctrl(struct uart_port *port, unsigned int mctrl) 1538 { 1539 u8 reg; 1540 1541 reg = readb(port->membase + UARTCR1); 1542 1543 /* for internal loopback we need LOOPS=1 and RSRC=0 */ 1544 reg &= ~(UARTCR1_LOOPS | UARTCR1_RSRC); 1545 if (mctrl & TIOCM_LOOP) 1546 reg |= UARTCR1_LOOPS; 1547 1548 writeb(reg, port->membase + UARTCR1); 1549 } 1550 1551 static void lpuart32_set_mctrl(struct uart_port *port, unsigned int mctrl) 1552 { 1553 u32 reg; 1554 1555 reg = lpuart32_read(port, UARTCTRL); 1556 1557 /* for internal loopback we need LOOPS=1 and RSRC=0 */ 1558 reg &= ~(UARTCTRL_LOOPS | UARTCTRL_RSRC); 1559 if (mctrl & TIOCM_LOOP) 1560 reg |= UARTCTRL_LOOPS; 1561 1562 lpuart32_write(port, reg, UARTCTRL); 1563 } 1564 1565 static void lpuart_break_ctl(struct uart_port *port, int break_state) 1566 { 1567 unsigned char temp; 1568 1569 temp = readb(port->membase + UARTCR2) & ~UARTCR2_SBK; 1570 1571 if (break_state != 0) 1572 temp |= UARTCR2_SBK; 1573 1574 writeb(temp, port->membase + UARTCR2); 1575 } 1576 1577 static void lpuart32_break_ctl(struct uart_port *port, int break_state) 1578 { 1579 unsigned long temp; 1580 1581 temp = lpuart32_read(port, UARTCTRL); 1582 1583 /* 1584 * LPUART IP now has two known bugs, one is CTS has higher priority than the 1585 * break signal, which causes the break signal sending through UARTCTRL_SBK 1586 * may impacted by the CTS input if the HW flow control is enabled. It 1587 * exists on all platforms we support in this driver. 1588 * Another bug is i.MX8QM LPUART may have an additional break character 1589 * being sent after SBK was cleared. 1590 * To avoid above two bugs, we use Transmit Data Inversion function to send 1591 * the break signal instead of UARTCTRL_SBK. 1592 */ 1593 if (break_state != 0) { 1594 /* 1595 * Disable the transmitter to prevent any data from being sent out 1596 * during break, then invert the TX line to send break. 1597 */ 1598 temp &= ~UARTCTRL_TE; 1599 lpuart32_write(port, temp, UARTCTRL); 1600 temp |= UARTCTRL_TXINV; 1601 lpuart32_write(port, temp, UARTCTRL); 1602 } else { 1603 /* Disable the TXINV to turn off break and re-enable transmitter. */ 1604 temp &= ~UARTCTRL_TXINV; 1605 lpuart32_write(port, temp, UARTCTRL); 1606 temp |= UARTCTRL_TE; 1607 lpuart32_write(port, temp, UARTCTRL); 1608 } 1609 } 1610 1611 static void lpuart_setup_watermark(struct lpuart_port *sport) 1612 { 1613 unsigned char val, cr2; 1614 unsigned char cr2_saved; 1615 1616 cr2 = readb(sport->port.membase + UARTCR2); 1617 cr2_saved = cr2; 1618 cr2 &= ~(UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_TE | 1619 UARTCR2_RIE | UARTCR2_RE); 1620 writeb(cr2, sport->port.membase + UARTCR2); 1621 1622 val = readb(sport->port.membase + UARTPFIFO); 1623 writeb(val | UARTPFIFO_TXFE | UARTPFIFO_RXFE, 1624 sport->port.membase + UARTPFIFO); 1625 1626 /* flush Tx and Rx FIFO */ 1627 writeb(UARTCFIFO_TXFLUSH | UARTCFIFO_RXFLUSH, 1628 sport->port.membase + UARTCFIFO); 1629 1630 /* explicitly clear RDRF */ 1631 if (readb(sport->port.membase + UARTSR1) & UARTSR1_RDRF) { 1632 readb(sport->port.membase + UARTDR); 1633 writeb(UARTSFIFO_RXUF, sport->port.membase + UARTSFIFO); 1634 } 1635 1636 if (uart_console(&sport->port)) 1637 sport->rx_watermark = 1; 1638 writeb(0, sport->port.membase + UARTTWFIFO); 1639 writeb(sport->rx_watermark, sport->port.membase + UARTRWFIFO); 1640 1641 /* Restore cr2 */ 1642 writeb(cr2_saved, sport->port.membase + UARTCR2); 1643 } 1644 1645 static void lpuart_setup_watermark_enable(struct lpuart_port *sport) 1646 { 1647 unsigned char cr2; 1648 1649 lpuart_setup_watermark(sport); 1650 1651 cr2 = readb(sport->port.membase + UARTCR2); 1652 cr2 |= UARTCR2_RIE | UARTCR2_RE | UARTCR2_TE; 1653 writeb(cr2, sport->port.membase + UARTCR2); 1654 } 1655 1656 static void lpuart32_setup_watermark(struct lpuart_port *sport) 1657 { 1658 unsigned long val, ctrl; 1659 unsigned long ctrl_saved; 1660 1661 ctrl = lpuart32_read(&sport->port, UARTCTRL); 1662 ctrl_saved = ctrl; 1663 ctrl &= ~(UARTCTRL_TIE | UARTCTRL_TCIE | UARTCTRL_TE | 1664 UARTCTRL_RIE | UARTCTRL_RE | UARTCTRL_ILIE); 1665 lpuart32_write(&sport->port, ctrl, UARTCTRL); 1666 1667 /* enable FIFO mode */ 1668 val = lpuart32_read(&sport->port, UARTFIFO); 1669 val |= UARTFIFO_TXFE | UARTFIFO_RXFE; 1670 val |= UARTFIFO_TXFLUSH | UARTFIFO_RXFLUSH; 1671 val |= FIELD_PREP(UARTFIFO_RXIDEN, 0x3); 1672 lpuart32_write(&sport->port, val, UARTFIFO); 1673 1674 /* set the watermark */ 1675 if (uart_console(&sport->port)) 1676 sport->rx_watermark = 1; 1677 val = (sport->rx_watermark << UARTWATER_RXWATER_OFF) | 1678 (0x0 << UARTWATER_TXWATER_OFF); 1679 lpuart32_write(&sport->port, val, UARTWATER); 1680 1681 /* set RTS watermark */ 1682 if (!uart_console(&sport->port)) { 1683 val = lpuart32_read(&sport->port, UARTMODIR); 1684 val |= FIELD_PREP(UARTMODIR_RTSWATER, sport->rxfifo_size >> 1); 1685 lpuart32_write(&sport->port, val, UARTMODIR); 1686 } 1687 1688 /* Restore cr2 */ 1689 lpuart32_write(&sport->port, ctrl_saved, UARTCTRL); 1690 } 1691 1692 static void lpuart32_setup_watermark_enable(struct lpuart_port *sport) 1693 { 1694 u32 temp; 1695 1696 lpuart32_setup_watermark(sport); 1697 1698 temp = lpuart32_read(&sport->port, UARTCTRL); 1699 temp |= UARTCTRL_RE | UARTCTRL_TE; 1700 temp |= FIELD_PREP(UARTCTRL_IDLECFG, 0x7); 1701 lpuart32_write(&sport->port, temp, UARTCTRL); 1702 } 1703 1704 static void rx_dma_timer_init(struct lpuart_port *sport) 1705 { 1706 if (sport->dma_idle_int) 1707 return; 1708 1709 timer_setup(&sport->lpuart_timer, lpuart_timer_func, 0); 1710 sport->lpuart_timer.expires = jiffies + sport->dma_rx_timeout; 1711 add_timer(&sport->lpuart_timer); 1712 } 1713 1714 static void lpuart_request_dma(struct lpuart_port *sport) 1715 { 1716 sport->dma_tx_chan = dma_request_chan(sport->port.dev, "tx"); 1717 if (IS_ERR(sport->dma_tx_chan)) { 1718 dev_dbg_once(sport->port.dev, 1719 "DMA tx channel request failed, operating without tx DMA (%ld)\n", 1720 PTR_ERR(sport->dma_tx_chan)); 1721 sport->dma_tx_chan = NULL; 1722 } 1723 1724 sport->dma_rx_chan = dma_request_chan(sport->port.dev, "rx"); 1725 if (IS_ERR(sport->dma_rx_chan)) { 1726 dev_dbg_once(sport->port.dev, 1727 "DMA rx channel request failed, operating without rx DMA (%ld)\n", 1728 PTR_ERR(sport->dma_rx_chan)); 1729 sport->dma_rx_chan = NULL; 1730 } 1731 } 1732 1733 static void lpuart_tx_dma_startup(struct lpuart_port *sport) 1734 { 1735 u32 uartbaud; 1736 int ret; 1737 1738 if (uart_console(&sport->port)) 1739 goto err; 1740 1741 if (!sport->dma_tx_chan) 1742 goto err; 1743 1744 ret = lpuart_dma_tx_request(&sport->port); 1745 if (ret) 1746 goto err; 1747 1748 init_waitqueue_head(&sport->dma_wait); 1749 sport->lpuart_dma_tx_use = true; 1750 if (lpuart_is_32(sport)) { 1751 uartbaud = lpuart32_read(&sport->port, UARTBAUD); 1752 lpuart32_write(&sport->port, 1753 uartbaud | UARTBAUD_TDMAE, UARTBAUD); 1754 } else { 1755 writeb(readb(sport->port.membase + UARTCR5) | 1756 UARTCR5_TDMAS, sport->port.membase + UARTCR5); 1757 } 1758 1759 return; 1760 1761 err: 1762 sport->lpuart_dma_tx_use = false; 1763 } 1764 1765 static void lpuart_rx_dma_startup(struct lpuart_port *sport) 1766 { 1767 int ret; 1768 unsigned char cr3; 1769 1770 if (uart_console(&sport->port)) 1771 goto err; 1772 1773 if (!sport->dma_rx_chan) 1774 goto err; 1775 1776 /* set default Rx DMA timeout */ 1777 sport->dma_rx_timeout = msecs_to_jiffies(DMA_RX_TIMEOUT); 1778 1779 ret = lpuart_start_rx_dma(sport); 1780 if (ret) 1781 goto err; 1782 1783 if (!sport->dma_rx_timeout) 1784 sport->dma_rx_timeout = 1; 1785 1786 sport->lpuart_dma_rx_use = true; 1787 rx_dma_timer_init(sport); 1788 1789 if (sport->port.has_sysrq && !lpuart_is_32(sport)) { 1790 cr3 = readb(sport->port.membase + UARTCR3); 1791 cr3 |= UARTCR3_FEIE; 1792 writeb(cr3, sport->port.membase + UARTCR3); 1793 } 1794 1795 return; 1796 1797 err: 1798 sport->lpuart_dma_rx_use = false; 1799 } 1800 1801 static void lpuart_hw_setup(struct lpuart_port *sport) 1802 { 1803 unsigned long flags; 1804 1805 uart_port_lock_irqsave(&sport->port, &flags); 1806 1807 lpuart_setup_watermark_enable(sport); 1808 1809 lpuart_rx_dma_startup(sport); 1810 lpuart_tx_dma_startup(sport); 1811 1812 uart_port_unlock_irqrestore(&sport->port, flags); 1813 } 1814 1815 static int lpuart_startup(struct uart_port *port) 1816 { 1817 struct lpuart_port *sport = container_of(port, struct lpuart_port, port); 1818 unsigned char temp; 1819 1820 /* determine FIFO size and enable FIFO mode */ 1821 temp = readb(sport->port.membase + UARTPFIFO); 1822 1823 sport->txfifo_size = UARTFIFO_DEPTH((temp >> UARTPFIFO_TXSIZE_OFF) & 1824 UARTPFIFO_FIFOSIZE_MASK); 1825 sport->port.fifosize = sport->txfifo_size; 1826 1827 sport->rxfifo_size = UARTFIFO_DEPTH((temp >> UARTPFIFO_RXSIZE_OFF) & 1828 UARTPFIFO_FIFOSIZE_MASK); 1829 1830 lpuart_request_dma(sport); 1831 lpuart_hw_setup(sport); 1832 1833 return 0; 1834 } 1835 1836 static void lpuart32_hw_disable(struct lpuart_port *sport) 1837 { 1838 unsigned long temp; 1839 1840 temp = lpuart32_read(&sport->port, UARTCTRL); 1841 temp &= ~(UARTCTRL_RIE | UARTCTRL_ILIE | UARTCTRL_RE | 1842 UARTCTRL_TIE | UARTCTRL_TE); 1843 lpuart32_write(&sport->port, temp, UARTCTRL); 1844 } 1845 1846 static void lpuart32_configure(struct lpuart_port *sport) 1847 { 1848 unsigned long temp; 1849 1850 temp = lpuart32_read(&sport->port, UARTCTRL); 1851 if (!sport->lpuart_dma_rx_use) 1852 temp |= UARTCTRL_RIE | UARTCTRL_ILIE; 1853 if (!sport->lpuart_dma_tx_use) 1854 temp |= UARTCTRL_TIE; 1855 lpuart32_write(&sport->port, temp, UARTCTRL); 1856 } 1857 1858 static void lpuart32_hw_setup(struct lpuart_port *sport) 1859 { 1860 unsigned long flags; 1861 1862 uart_port_lock_irqsave(&sport->port, &flags); 1863 1864 lpuart32_hw_disable(sport); 1865 1866 lpuart_rx_dma_startup(sport); 1867 lpuart_tx_dma_startup(sport); 1868 1869 lpuart32_setup_watermark_enable(sport); 1870 lpuart32_configure(sport); 1871 1872 uart_port_unlock_irqrestore(&sport->port, flags); 1873 } 1874 1875 static int lpuart32_startup(struct uart_port *port) 1876 { 1877 struct lpuart_port *sport = container_of(port, struct lpuart_port, port); 1878 unsigned long temp; 1879 1880 /* determine FIFO size */ 1881 temp = lpuart32_read(&sport->port, UARTFIFO); 1882 1883 sport->txfifo_size = UARTFIFO_DEPTH((temp >> UARTFIFO_TXSIZE_OFF) & 1884 UARTFIFO_FIFOSIZE_MASK); 1885 sport->port.fifosize = sport->txfifo_size; 1886 1887 sport->rxfifo_size = UARTFIFO_DEPTH((temp >> UARTFIFO_RXSIZE_OFF) & 1888 UARTFIFO_FIFOSIZE_MASK); 1889 1890 /* 1891 * The LS1021A and LS1028A have a fixed FIFO depth of 16 words. 1892 * Although they support the RX/TXSIZE fields, their encoding is 1893 * different. Eg the reference manual states 0b101 is 16 words. 1894 */ 1895 if (is_layerscape_lpuart(sport)) { 1896 sport->rxfifo_size = 16; 1897 sport->txfifo_size = 16; 1898 sport->port.fifosize = sport->txfifo_size; 1899 } 1900 1901 lpuart_request_dma(sport); 1902 lpuart32_hw_setup(sport); 1903 1904 return 0; 1905 } 1906 1907 static void lpuart_dma_shutdown(struct lpuart_port *sport) 1908 { 1909 if (sport->lpuart_dma_rx_use) { 1910 lpuart_dma_rx_free(&sport->port); 1911 sport->lpuart_dma_rx_use = false; 1912 } 1913 1914 if (sport->lpuart_dma_tx_use) { 1915 if (wait_event_interruptible_timeout(sport->dma_wait, 1916 !sport->dma_tx_in_progress, msecs_to_jiffies(300)) <= 0) { 1917 sport->dma_tx_in_progress = false; 1918 dmaengine_terminate_sync(sport->dma_tx_chan); 1919 } 1920 sport->lpuart_dma_tx_use = false; 1921 } 1922 1923 if (sport->dma_tx_chan) 1924 dma_release_channel(sport->dma_tx_chan); 1925 if (sport->dma_rx_chan) 1926 dma_release_channel(sport->dma_rx_chan); 1927 } 1928 1929 static void lpuart_shutdown(struct uart_port *port) 1930 { 1931 struct lpuart_port *sport = container_of(port, struct lpuart_port, port); 1932 unsigned char temp; 1933 unsigned long flags; 1934 1935 uart_port_lock_irqsave(port, &flags); 1936 1937 /* disable Rx/Tx and interrupts */ 1938 temp = readb(port->membase + UARTCR2); 1939 temp &= ~(UARTCR2_TE | UARTCR2_RE | 1940 UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_RIE); 1941 writeb(temp, port->membase + UARTCR2); 1942 1943 uart_port_unlock_irqrestore(port, flags); 1944 1945 lpuart_dma_shutdown(sport); 1946 } 1947 1948 static void lpuart32_shutdown(struct uart_port *port) 1949 { 1950 struct lpuart_port *sport = 1951 container_of(port, struct lpuart_port, port); 1952 unsigned long temp; 1953 unsigned long flags; 1954 1955 uart_port_lock_irqsave(port, &flags); 1956 1957 /* clear status */ 1958 temp = lpuart32_read(&sport->port, UARTSTAT); 1959 lpuart32_write(&sport->port, temp, UARTSTAT); 1960 1961 /* disable Rx/Tx DMA */ 1962 temp = lpuart32_read(port, UARTBAUD); 1963 temp &= ~(UARTBAUD_TDMAE | UARTBAUD_RDMAE); 1964 lpuart32_write(port, temp, UARTBAUD); 1965 1966 /* disable Rx/Tx and interrupts and break condition */ 1967 temp = lpuart32_read(port, UARTCTRL); 1968 temp &= ~(UARTCTRL_TE | UARTCTRL_RE | UARTCTRL_ILIE | 1969 UARTCTRL_TIE | UARTCTRL_TCIE | UARTCTRL_RIE | UARTCTRL_SBK); 1970 lpuart32_write(port, temp, UARTCTRL); 1971 1972 uart_port_unlock_irqrestore(port, flags); 1973 1974 lpuart_dma_shutdown(sport); 1975 } 1976 1977 static void 1978 lpuart_set_termios(struct uart_port *port, struct ktermios *termios, 1979 const struct ktermios *old) 1980 { 1981 struct lpuart_port *sport = container_of(port, struct lpuart_port, port); 1982 unsigned long flags; 1983 unsigned char cr1, old_cr1, old_cr2, cr3, cr4, bdh, modem; 1984 unsigned int baud; 1985 unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8; 1986 unsigned int sbr, brfa; 1987 1988 cr1 = old_cr1 = readb(sport->port.membase + UARTCR1); 1989 old_cr2 = readb(sport->port.membase + UARTCR2); 1990 cr3 = readb(sport->port.membase + UARTCR3); 1991 cr4 = readb(sport->port.membase + UARTCR4); 1992 bdh = readb(sport->port.membase + UARTBDH); 1993 modem = readb(sport->port.membase + UARTMODEM); 1994 /* 1995 * only support CS8 and CS7, and for CS7 must enable PE. 1996 * supported mode: 1997 * - (7,e/o,1) 1998 * - (8,n,1) 1999 * - (8,m/s,1) 2000 * - (8,e/o,1) 2001 */ 2002 while ((termios->c_cflag & CSIZE) != CS8 && 2003 (termios->c_cflag & CSIZE) != CS7) { 2004 termios->c_cflag &= ~CSIZE; 2005 termios->c_cflag |= old_csize; 2006 old_csize = CS8; 2007 } 2008 2009 if ((termios->c_cflag & CSIZE) == CS8 || 2010 (termios->c_cflag & CSIZE) == CS7) 2011 cr1 = old_cr1 & ~UARTCR1_M; 2012 2013 if (termios->c_cflag & CMSPAR) { 2014 if ((termios->c_cflag & CSIZE) != CS8) { 2015 termios->c_cflag &= ~CSIZE; 2016 termios->c_cflag |= CS8; 2017 } 2018 cr1 |= UARTCR1_M; 2019 } 2020 2021 /* 2022 * When auto RS-485 RTS mode is enabled, 2023 * hardware flow control need to be disabled. 2024 */ 2025 if (sport->port.rs485.flags & SER_RS485_ENABLED) 2026 termios->c_cflag &= ~CRTSCTS; 2027 2028 if (termios->c_cflag & CRTSCTS) 2029 modem |= UARTMODEM_RXRTSE | UARTMODEM_TXCTSE; 2030 else 2031 modem &= ~(UARTMODEM_RXRTSE | UARTMODEM_TXCTSE); 2032 2033 termios->c_cflag &= ~CSTOPB; 2034 2035 /* parity must be enabled when CS7 to match 8-bits format */ 2036 if ((termios->c_cflag & CSIZE) == CS7) 2037 termios->c_cflag |= PARENB; 2038 2039 if (termios->c_cflag & PARENB) { 2040 if (termios->c_cflag & CMSPAR) { 2041 cr1 &= ~UARTCR1_PE; 2042 if (termios->c_cflag & PARODD) 2043 cr3 |= UARTCR3_T8; 2044 else 2045 cr3 &= ~UARTCR3_T8; 2046 } else { 2047 cr1 |= UARTCR1_PE; 2048 if ((termios->c_cflag & CSIZE) == CS8) 2049 cr1 |= UARTCR1_M; 2050 if (termios->c_cflag & PARODD) 2051 cr1 |= UARTCR1_PT; 2052 else 2053 cr1 &= ~UARTCR1_PT; 2054 } 2055 } else { 2056 cr1 &= ~UARTCR1_PE; 2057 } 2058 2059 /* ask the core to calculate the divisor */ 2060 baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 16); 2061 2062 /* 2063 * Need to update the Ring buffer length according to the selected 2064 * baud rate and restart Rx DMA path. 2065 * 2066 * Since timer function acqures sport->port.lock, need to stop before 2067 * acquring same lock because otherwise del_timer_sync() can deadlock. 2068 */ 2069 if (old && sport->lpuart_dma_rx_use) 2070 lpuart_dma_rx_free(&sport->port); 2071 2072 uart_port_lock_irqsave(&sport->port, &flags); 2073 2074 sport->port.read_status_mask = 0; 2075 if (termios->c_iflag & INPCK) 2076 sport->port.read_status_mask |= UARTSR1_FE | UARTSR1_PE; 2077 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) 2078 sport->port.read_status_mask |= UARTSR1_FE; 2079 2080 /* characters to ignore */ 2081 sport->port.ignore_status_mask = 0; 2082 if (termios->c_iflag & IGNPAR) 2083 sport->port.ignore_status_mask |= UARTSR1_PE; 2084 if (termios->c_iflag & IGNBRK) { 2085 sport->port.ignore_status_mask |= UARTSR1_FE; 2086 /* 2087 * if we're ignoring parity and break indicators, 2088 * ignore overruns too (for real raw support). 2089 */ 2090 if (termios->c_iflag & IGNPAR) 2091 sport->port.ignore_status_mask |= UARTSR1_OR; 2092 } 2093 2094 /* update the per-port timeout */ 2095 uart_update_timeout(port, termios->c_cflag, baud); 2096 2097 /* wait transmit engin complete */ 2098 lpuart_wait_bit_set(&sport->port, UARTSR1, UARTSR1_TC); 2099 2100 /* disable transmit and receive */ 2101 writeb(old_cr2 & ~(UARTCR2_TE | UARTCR2_RE), 2102 sport->port.membase + UARTCR2); 2103 2104 sbr = sport->port.uartclk / (16 * baud); 2105 brfa = ((sport->port.uartclk - (16 * sbr * baud)) * 2) / baud; 2106 bdh &= ~UARTBDH_SBR_MASK; 2107 bdh |= (sbr >> 8) & 0x1F; 2108 cr4 &= ~UARTCR4_BRFA_MASK; 2109 brfa &= UARTCR4_BRFA_MASK; 2110 writeb(cr4 | brfa, sport->port.membase + UARTCR4); 2111 writeb(bdh, sport->port.membase + UARTBDH); 2112 writeb(sbr & 0xFF, sport->port.membase + UARTBDL); 2113 writeb(cr3, sport->port.membase + UARTCR3); 2114 writeb(cr1, sport->port.membase + UARTCR1); 2115 writeb(modem, sport->port.membase + UARTMODEM); 2116 2117 /* restore control register */ 2118 writeb(old_cr2, sport->port.membase + UARTCR2); 2119 2120 if (old && sport->lpuart_dma_rx_use) { 2121 if (!lpuart_start_rx_dma(sport)) 2122 rx_dma_timer_init(sport); 2123 else 2124 sport->lpuart_dma_rx_use = false; 2125 } 2126 2127 uart_port_unlock_irqrestore(&sport->port, flags); 2128 } 2129 2130 static void __lpuart32_serial_setbrg(struct uart_port *port, 2131 unsigned int baudrate, bool use_rx_dma, 2132 bool use_tx_dma) 2133 { 2134 u32 sbr, osr, baud_diff, tmp_osr, tmp_sbr, tmp_diff, tmp; 2135 u32 clk = port->uartclk; 2136 2137 /* 2138 * The idea is to use the best OSR (over-sampling rate) possible. 2139 * Note, OSR is typically hard-set to 16 in other LPUART instantiations. 2140 * Loop to find the best OSR value possible, one that generates minimum 2141 * baud_diff iterate through the rest of the supported values of OSR. 2142 * 2143 * Calculation Formula: 2144 * Baud Rate = baud clock / ((OSR+1) × SBR) 2145 */ 2146 baud_diff = baudrate; 2147 osr = 0; 2148 sbr = 0; 2149 2150 for (tmp_osr = 4; tmp_osr <= 32; tmp_osr++) { 2151 /* calculate the temporary sbr value */ 2152 tmp_sbr = (clk / (baudrate * tmp_osr)); 2153 if (tmp_sbr == 0) 2154 tmp_sbr = 1; 2155 2156 /* 2157 * calculate the baud rate difference based on the temporary 2158 * osr and sbr values 2159 */ 2160 tmp_diff = clk / (tmp_osr * tmp_sbr) - baudrate; 2161 2162 /* select best values between sbr and sbr+1 */ 2163 tmp = clk / (tmp_osr * (tmp_sbr + 1)); 2164 if (tmp_diff > (baudrate - tmp)) { 2165 tmp_diff = baudrate - tmp; 2166 tmp_sbr++; 2167 } 2168 2169 if (tmp_sbr > UARTBAUD_SBR_MASK) 2170 continue; 2171 2172 if (tmp_diff <= baud_diff) { 2173 baud_diff = tmp_diff; 2174 osr = tmp_osr; 2175 sbr = tmp_sbr; 2176 2177 if (!baud_diff) 2178 break; 2179 } 2180 } 2181 2182 /* handle buadrate outside acceptable rate */ 2183 if (baud_diff > ((baudrate / 100) * 3)) 2184 dev_warn(port->dev, 2185 "unacceptable baud rate difference of more than 3%%\n"); 2186 2187 tmp = lpuart32_read(port, UARTBAUD); 2188 2189 if ((osr > 3) && (osr < 8)) 2190 tmp |= UARTBAUD_BOTHEDGE; 2191 2192 tmp &= ~(UARTBAUD_OSR_MASK << UARTBAUD_OSR_SHIFT); 2193 tmp |= ((osr-1) & UARTBAUD_OSR_MASK) << UARTBAUD_OSR_SHIFT; 2194 2195 tmp &= ~UARTBAUD_SBR_MASK; 2196 tmp |= sbr & UARTBAUD_SBR_MASK; 2197 2198 if (!use_rx_dma) 2199 tmp &= ~UARTBAUD_RDMAE; 2200 if (!use_tx_dma) 2201 tmp &= ~UARTBAUD_TDMAE; 2202 2203 lpuart32_write(port, tmp, UARTBAUD); 2204 } 2205 2206 static void lpuart32_serial_setbrg(struct lpuart_port *sport, 2207 unsigned int baudrate) 2208 { 2209 __lpuart32_serial_setbrg(&sport->port, baudrate, 2210 sport->lpuart_dma_rx_use, 2211 sport->lpuart_dma_tx_use); 2212 } 2213 2214 2215 static void 2216 lpuart32_set_termios(struct uart_port *port, struct ktermios *termios, 2217 const struct ktermios *old) 2218 { 2219 struct lpuart_port *sport = container_of(port, struct lpuart_port, port); 2220 unsigned long flags; 2221 unsigned long ctrl, old_ctrl, bd, modem; 2222 unsigned int baud; 2223 unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8; 2224 2225 ctrl = old_ctrl = lpuart32_read(&sport->port, UARTCTRL); 2226 bd = lpuart32_read(&sport->port, UARTBAUD); 2227 modem = lpuart32_read(&sport->port, UARTMODIR); 2228 sport->is_cs7 = false; 2229 /* 2230 * only support CS8 and CS7, and for CS7 must enable PE. 2231 * supported mode: 2232 * - (7,e/o,1) 2233 * - (8,n,1) 2234 * - (8,m/s,1) 2235 * - (8,e/o,1) 2236 */ 2237 while ((termios->c_cflag & CSIZE) != CS8 && 2238 (termios->c_cflag & CSIZE) != CS7) { 2239 termios->c_cflag &= ~CSIZE; 2240 termios->c_cflag |= old_csize; 2241 old_csize = CS8; 2242 } 2243 2244 if ((termios->c_cflag & CSIZE) == CS8 || 2245 (termios->c_cflag & CSIZE) == CS7) 2246 ctrl = old_ctrl & ~UARTCTRL_M; 2247 2248 if (termios->c_cflag & CMSPAR) { 2249 if ((termios->c_cflag & CSIZE) != CS8) { 2250 termios->c_cflag &= ~CSIZE; 2251 termios->c_cflag |= CS8; 2252 } 2253 ctrl |= UARTCTRL_M; 2254 } 2255 2256 /* 2257 * When auto RS-485 RTS mode is enabled, 2258 * hardware flow control need to be disabled. 2259 */ 2260 if (sport->port.rs485.flags & SER_RS485_ENABLED) 2261 termios->c_cflag &= ~CRTSCTS; 2262 2263 if (termios->c_cflag & CRTSCTS) 2264 modem |= UARTMODIR_RXRTSE | UARTMODIR_TXCTSE; 2265 else 2266 modem &= ~(UARTMODIR_RXRTSE | UARTMODIR_TXCTSE); 2267 2268 if (termios->c_cflag & CSTOPB) 2269 bd |= UARTBAUD_SBNS; 2270 else 2271 bd &= ~UARTBAUD_SBNS; 2272 2273 /* parity must be enabled when CS7 to match 8-bits format */ 2274 if ((termios->c_cflag & CSIZE) == CS7) 2275 termios->c_cflag |= PARENB; 2276 2277 if ((termios->c_cflag & PARENB)) { 2278 if (termios->c_cflag & CMSPAR) { 2279 ctrl &= ~UARTCTRL_PE; 2280 ctrl |= UARTCTRL_M; 2281 } else { 2282 ctrl |= UARTCTRL_PE; 2283 if ((termios->c_cflag & CSIZE) == CS8) 2284 ctrl |= UARTCTRL_M; 2285 if (termios->c_cflag & PARODD) 2286 ctrl |= UARTCTRL_PT; 2287 else 2288 ctrl &= ~UARTCTRL_PT; 2289 } 2290 } else { 2291 ctrl &= ~UARTCTRL_PE; 2292 } 2293 2294 /* ask the core to calculate the divisor */ 2295 baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 4); 2296 2297 /* 2298 * Need to update the Ring buffer length according to the selected 2299 * baud rate and restart Rx DMA path. 2300 * 2301 * Since timer function acqures sport->port.lock, need to stop before 2302 * acquring same lock because otherwise del_timer_sync() can deadlock. 2303 */ 2304 if (old && sport->lpuart_dma_rx_use) 2305 lpuart_dma_rx_free(&sport->port); 2306 2307 uart_port_lock_irqsave(&sport->port, &flags); 2308 2309 sport->port.read_status_mask = 0; 2310 if (termios->c_iflag & INPCK) 2311 sport->port.read_status_mask |= UARTSTAT_FE | UARTSTAT_PE; 2312 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) 2313 sport->port.read_status_mask |= UARTSTAT_FE; 2314 2315 /* characters to ignore */ 2316 sport->port.ignore_status_mask = 0; 2317 if (termios->c_iflag & IGNPAR) 2318 sport->port.ignore_status_mask |= UARTSTAT_PE; 2319 if (termios->c_iflag & IGNBRK) { 2320 sport->port.ignore_status_mask |= UARTSTAT_FE; 2321 /* 2322 * if we're ignoring parity and break indicators, 2323 * ignore overruns too (for real raw support). 2324 */ 2325 if (termios->c_iflag & IGNPAR) 2326 sport->port.ignore_status_mask |= UARTSTAT_OR; 2327 } 2328 2329 /* update the per-port timeout */ 2330 uart_update_timeout(port, termios->c_cflag, baud); 2331 2332 /* 2333 * LPUART Transmission Complete Flag may never be set while queuing a break 2334 * character, so skip waiting for transmission complete when UARTCTRL_SBK is 2335 * asserted. 2336 */ 2337 if (!(old_ctrl & UARTCTRL_SBK)) { 2338 lpuart32_write(&sport->port, 0, UARTMODIR); 2339 lpuart32_wait_bit_set(&sport->port, UARTSTAT, UARTSTAT_TC); 2340 } 2341 2342 /* disable transmit and receive */ 2343 lpuart32_write(&sport->port, old_ctrl & ~(UARTCTRL_TE | UARTCTRL_RE), 2344 UARTCTRL); 2345 2346 lpuart32_write(&sport->port, bd, UARTBAUD); 2347 lpuart32_serial_setbrg(sport, baud); 2348 /* disable CTS before enabling UARTCTRL_TE to avoid pending idle preamble */ 2349 lpuart32_write(&sport->port, modem & ~UARTMODIR_TXCTSE, UARTMODIR); 2350 /* restore control register */ 2351 lpuart32_write(&sport->port, ctrl, UARTCTRL); 2352 /* re-enable the CTS if needed */ 2353 lpuart32_write(&sport->port, modem, UARTMODIR); 2354 2355 if ((ctrl & (UARTCTRL_PE | UARTCTRL_M)) == UARTCTRL_PE) 2356 sport->is_cs7 = true; 2357 2358 if (old && sport->lpuart_dma_rx_use) { 2359 if (!lpuart_start_rx_dma(sport)) 2360 rx_dma_timer_init(sport); 2361 else 2362 sport->lpuart_dma_rx_use = false; 2363 } 2364 2365 uart_port_unlock_irqrestore(&sport->port, flags); 2366 } 2367 2368 static const char *lpuart_type(struct uart_port *port) 2369 { 2370 return "FSL_LPUART"; 2371 } 2372 2373 static void lpuart_release_port(struct uart_port *port) 2374 { 2375 /* nothing to do */ 2376 } 2377 2378 static int lpuart_request_port(struct uart_port *port) 2379 { 2380 return 0; 2381 } 2382 2383 /* configure/autoconfigure the port */ 2384 static void lpuart_config_port(struct uart_port *port, int flags) 2385 { 2386 if (flags & UART_CONFIG_TYPE) 2387 port->type = PORT_LPUART; 2388 } 2389 2390 static int lpuart_verify_port(struct uart_port *port, struct serial_struct *ser) 2391 { 2392 int ret = 0; 2393 2394 if (ser->type != PORT_UNKNOWN && ser->type != PORT_LPUART) 2395 ret = -EINVAL; 2396 if (port->irq != ser->irq) 2397 ret = -EINVAL; 2398 if (ser->io_type != UPIO_MEM) 2399 ret = -EINVAL; 2400 if (port->uartclk / 16 != ser->baud_base) 2401 ret = -EINVAL; 2402 if (port->iobase != ser->port) 2403 ret = -EINVAL; 2404 if (ser->hub6 != 0) 2405 ret = -EINVAL; 2406 return ret; 2407 } 2408 2409 static const struct uart_ops lpuart_pops = { 2410 .tx_empty = lpuart_tx_empty, 2411 .set_mctrl = lpuart_set_mctrl, 2412 .get_mctrl = lpuart_get_mctrl, 2413 .stop_tx = lpuart_stop_tx, 2414 .start_tx = lpuart_start_tx, 2415 .stop_rx = lpuart_stop_rx, 2416 .break_ctl = lpuart_break_ctl, 2417 .startup = lpuart_startup, 2418 .shutdown = lpuart_shutdown, 2419 .set_termios = lpuart_set_termios, 2420 .pm = lpuart_uart_pm, 2421 .type = lpuart_type, 2422 .request_port = lpuart_request_port, 2423 .release_port = lpuart_release_port, 2424 .config_port = lpuart_config_port, 2425 .verify_port = lpuart_verify_port, 2426 .flush_buffer = lpuart_flush_buffer, 2427 #if defined(CONFIG_CONSOLE_POLL) 2428 .poll_init = lpuart_poll_init, 2429 .poll_get_char = lpuart_poll_get_char, 2430 .poll_put_char = lpuart_poll_put_char, 2431 #endif 2432 }; 2433 2434 static const struct uart_ops lpuart32_pops = { 2435 .tx_empty = lpuart32_tx_empty, 2436 .set_mctrl = lpuart32_set_mctrl, 2437 .get_mctrl = lpuart32_get_mctrl, 2438 .stop_tx = lpuart32_stop_tx, 2439 .start_tx = lpuart32_start_tx, 2440 .stop_rx = lpuart32_stop_rx, 2441 .break_ctl = lpuart32_break_ctl, 2442 .startup = lpuart32_startup, 2443 .shutdown = lpuart32_shutdown, 2444 .set_termios = lpuart32_set_termios, 2445 .pm = lpuart_uart_pm, 2446 .type = lpuart_type, 2447 .request_port = lpuart_request_port, 2448 .release_port = lpuart_release_port, 2449 .config_port = lpuart_config_port, 2450 .verify_port = lpuart_verify_port, 2451 .flush_buffer = lpuart_flush_buffer, 2452 #if defined(CONFIG_CONSOLE_POLL) 2453 .poll_init = lpuart32_poll_init, 2454 .poll_get_char = lpuart32_poll_get_char, 2455 .poll_put_char = lpuart32_poll_put_char, 2456 #endif 2457 }; 2458 2459 static struct lpuart_port *lpuart_ports[UART_NR]; 2460 2461 #ifdef CONFIG_SERIAL_FSL_LPUART_CONSOLE 2462 static void lpuart_console_putchar(struct uart_port *port, unsigned char ch) 2463 { 2464 lpuart_wait_bit_set(port, UARTSR1, UARTSR1_TDRE); 2465 writeb(ch, port->membase + UARTDR); 2466 } 2467 2468 static void lpuart32_console_putchar(struct uart_port *port, unsigned char ch) 2469 { 2470 lpuart32_wait_bit_set(port, UARTSTAT, UARTSTAT_TDRE); 2471 lpuart32_write(port, ch, UARTDATA); 2472 } 2473 2474 static void 2475 lpuart_console_write(struct console *co, const char *s, unsigned int count) 2476 { 2477 struct lpuart_port *sport = lpuart_ports[co->index]; 2478 unsigned char old_cr2, cr2; 2479 unsigned long flags; 2480 int locked = 1; 2481 2482 if (oops_in_progress) 2483 locked = uart_port_trylock_irqsave(&sport->port, &flags); 2484 else 2485 uart_port_lock_irqsave(&sport->port, &flags); 2486 2487 /* first save CR2 and then disable interrupts */ 2488 cr2 = old_cr2 = readb(sport->port.membase + UARTCR2); 2489 cr2 |= UARTCR2_TE | UARTCR2_RE; 2490 cr2 &= ~(UARTCR2_TIE | UARTCR2_TCIE | UARTCR2_RIE); 2491 writeb(cr2, sport->port.membase + UARTCR2); 2492 2493 uart_console_write(&sport->port, s, count, lpuart_console_putchar); 2494 2495 /* wait for transmitter finish complete and restore CR2 */ 2496 lpuart_wait_bit_set(&sport->port, UARTSR1, UARTSR1_TC); 2497 2498 writeb(old_cr2, sport->port.membase + UARTCR2); 2499 2500 if (locked) 2501 uart_port_unlock_irqrestore(&sport->port, flags); 2502 } 2503 2504 static void 2505 lpuart32_console_write(struct console *co, const char *s, unsigned int count) 2506 { 2507 struct lpuart_port *sport = lpuart_ports[co->index]; 2508 unsigned long old_cr, cr; 2509 unsigned long flags; 2510 int locked = 1; 2511 2512 if (oops_in_progress) 2513 locked = uart_port_trylock_irqsave(&sport->port, &flags); 2514 else 2515 uart_port_lock_irqsave(&sport->port, &flags); 2516 2517 /* first save CR2 and then disable interrupts */ 2518 cr = old_cr = lpuart32_read(&sport->port, UARTCTRL); 2519 cr |= UARTCTRL_TE | UARTCTRL_RE; 2520 cr &= ~(UARTCTRL_TIE | UARTCTRL_TCIE | UARTCTRL_RIE); 2521 lpuart32_write(&sport->port, cr, UARTCTRL); 2522 2523 uart_console_write(&sport->port, s, count, lpuart32_console_putchar); 2524 2525 /* wait for transmitter finish complete and restore CR2 */ 2526 lpuart32_wait_bit_set(&sport->port, UARTSTAT, UARTSTAT_TC); 2527 2528 lpuart32_write(&sport->port, old_cr, UARTCTRL); 2529 2530 if (locked) 2531 uart_port_unlock_irqrestore(&sport->port, flags); 2532 } 2533 2534 /* 2535 * if the port was already initialised (eg, by a boot loader), 2536 * try to determine the current setup. 2537 */ 2538 static void __init 2539 lpuart_console_get_options(struct lpuart_port *sport, int *baud, 2540 int *parity, int *bits) 2541 { 2542 unsigned char cr, bdh, bdl, brfa; 2543 unsigned int sbr, uartclk, baud_raw; 2544 2545 cr = readb(sport->port.membase + UARTCR2); 2546 cr &= UARTCR2_TE | UARTCR2_RE; 2547 if (!cr) 2548 return; 2549 2550 /* ok, the port was enabled */ 2551 2552 cr = readb(sport->port.membase + UARTCR1); 2553 2554 *parity = 'n'; 2555 if (cr & UARTCR1_PE) { 2556 if (cr & UARTCR1_PT) 2557 *parity = 'o'; 2558 else 2559 *parity = 'e'; 2560 } 2561 2562 if (cr & UARTCR1_M) 2563 *bits = 9; 2564 else 2565 *bits = 8; 2566 2567 bdh = readb(sport->port.membase + UARTBDH); 2568 bdh &= UARTBDH_SBR_MASK; 2569 bdl = readb(sport->port.membase + UARTBDL); 2570 sbr = bdh; 2571 sbr <<= 8; 2572 sbr |= bdl; 2573 brfa = readb(sport->port.membase + UARTCR4); 2574 brfa &= UARTCR4_BRFA_MASK; 2575 2576 uartclk = lpuart_get_baud_clk_rate(sport); 2577 /* 2578 * baud = mod_clk/(16*(sbr[13]+(brfa)/32) 2579 */ 2580 baud_raw = uartclk / (16 * (sbr + brfa / 32)); 2581 2582 if (*baud != baud_raw) 2583 dev_info(sport->port.dev, "Serial: Console lpuart rounded baud rate" 2584 "from %d to %d\n", baud_raw, *baud); 2585 } 2586 2587 static void __init 2588 lpuart32_console_get_options(struct lpuart_port *sport, int *baud, 2589 int *parity, int *bits) 2590 { 2591 unsigned long cr, bd; 2592 unsigned int sbr, uartclk, baud_raw; 2593 2594 cr = lpuart32_read(&sport->port, UARTCTRL); 2595 cr &= UARTCTRL_TE | UARTCTRL_RE; 2596 if (!cr) 2597 return; 2598 2599 /* ok, the port was enabled */ 2600 2601 cr = lpuart32_read(&sport->port, UARTCTRL); 2602 2603 *parity = 'n'; 2604 if (cr & UARTCTRL_PE) { 2605 if (cr & UARTCTRL_PT) 2606 *parity = 'o'; 2607 else 2608 *parity = 'e'; 2609 } 2610 2611 if (cr & UARTCTRL_M) 2612 *bits = 9; 2613 else 2614 *bits = 8; 2615 2616 bd = lpuart32_read(&sport->port, UARTBAUD); 2617 bd &= UARTBAUD_SBR_MASK; 2618 if (!bd) 2619 return; 2620 2621 sbr = bd; 2622 uartclk = lpuart_get_baud_clk_rate(sport); 2623 /* 2624 * baud = mod_clk/(16*(sbr[13]+(brfa)/32) 2625 */ 2626 baud_raw = uartclk / (16 * sbr); 2627 2628 if (*baud != baud_raw) 2629 dev_info(sport->port.dev, "Serial: Console lpuart rounded baud rate" 2630 "from %d to %d\n", baud_raw, *baud); 2631 } 2632 2633 static int __init lpuart_console_setup(struct console *co, char *options) 2634 { 2635 struct lpuart_port *sport; 2636 int baud = 115200; 2637 int bits = 8; 2638 int parity = 'n'; 2639 int flow = 'n'; 2640 2641 /* 2642 * check whether an invalid uart number has been specified, and 2643 * if so, search for the first available port that does have 2644 * console support. 2645 */ 2646 if (co->index == -1 || co->index >= ARRAY_SIZE(lpuart_ports)) 2647 co->index = 0; 2648 2649 sport = lpuart_ports[co->index]; 2650 if (sport == NULL) 2651 return -ENODEV; 2652 2653 if (options) 2654 uart_parse_options(options, &baud, &parity, &bits, &flow); 2655 else 2656 if (lpuart_is_32(sport)) 2657 lpuart32_console_get_options(sport, &baud, &parity, &bits); 2658 else 2659 lpuart_console_get_options(sport, &baud, &parity, &bits); 2660 2661 if (lpuart_is_32(sport)) 2662 lpuart32_setup_watermark(sport); 2663 else 2664 lpuart_setup_watermark(sport); 2665 2666 return uart_set_options(&sport->port, co, baud, parity, bits, flow); 2667 } 2668 2669 static struct uart_driver lpuart_reg; 2670 static struct console lpuart_console = { 2671 .name = DEV_NAME, 2672 .write = lpuart_console_write, 2673 .device = uart_console_device, 2674 .setup = lpuart_console_setup, 2675 .flags = CON_PRINTBUFFER, 2676 .index = -1, 2677 .data = &lpuart_reg, 2678 }; 2679 2680 static struct console lpuart32_console = { 2681 .name = DEV_NAME, 2682 .write = lpuart32_console_write, 2683 .device = uart_console_device, 2684 .setup = lpuart_console_setup, 2685 .flags = CON_PRINTBUFFER, 2686 .index = -1, 2687 .data = &lpuart_reg, 2688 }; 2689 2690 static void lpuart_early_write(struct console *con, const char *s, unsigned n) 2691 { 2692 struct earlycon_device *dev = con->data; 2693 2694 uart_console_write(&dev->port, s, n, lpuart_console_putchar); 2695 } 2696 2697 static void lpuart32_early_write(struct console *con, const char *s, unsigned n) 2698 { 2699 struct earlycon_device *dev = con->data; 2700 2701 uart_console_write(&dev->port, s, n, lpuart32_console_putchar); 2702 } 2703 2704 static int __init lpuart_early_console_setup(struct earlycon_device *device, 2705 const char *opt) 2706 { 2707 if (!device->port.membase) 2708 return -ENODEV; 2709 2710 device->con->write = lpuart_early_write; 2711 return 0; 2712 } 2713 2714 static int __init lpuart32_early_console_setup(struct earlycon_device *device, 2715 const char *opt) 2716 { 2717 if (!device->port.membase) 2718 return -ENODEV; 2719 2720 if (device->port.iotype != UPIO_MEM32) 2721 device->port.iotype = UPIO_MEM32BE; 2722 2723 device->con->write = lpuart32_early_write; 2724 return 0; 2725 } 2726 2727 static int __init ls1028a_early_console_setup(struct earlycon_device *device, 2728 const char *opt) 2729 { 2730 u32 cr; 2731 2732 if (!device->port.membase) 2733 return -ENODEV; 2734 2735 device->port.iotype = UPIO_MEM32; 2736 device->con->write = lpuart32_early_write; 2737 2738 /* set the baudrate */ 2739 if (device->port.uartclk && device->baud) 2740 __lpuart32_serial_setbrg(&device->port, device->baud, 2741 false, false); 2742 2743 /* enable transmitter */ 2744 cr = lpuart32_read(&device->port, UARTCTRL); 2745 cr |= UARTCTRL_TE; 2746 lpuart32_write(&device->port, cr, UARTCTRL); 2747 2748 return 0; 2749 } 2750 2751 static int __init lpuart32_imx_early_console_setup(struct earlycon_device *device, 2752 const char *opt) 2753 { 2754 if (!device->port.membase) 2755 return -ENODEV; 2756 2757 device->port.iotype = UPIO_MEM32; 2758 device->port.membase += IMX_REG_OFF; 2759 device->con->write = lpuart32_early_write; 2760 2761 return 0; 2762 } 2763 OF_EARLYCON_DECLARE(lpuart, "fsl,vf610-lpuart", lpuart_early_console_setup); 2764 OF_EARLYCON_DECLARE(lpuart32, "fsl,ls1021a-lpuart", lpuart32_early_console_setup); 2765 OF_EARLYCON_DECLARE(lpuart32, "fsl,ls1028a-lpuart", ls1028a_early_console_setup); 2766 OF_EARLYCON_DECLARE(lpuart32, "fsl,imx7ulp-lpuart", lpuart32_imx_early_console_setup); 2767 OF_EARLYCON_DECLARE(lpuart32, "fsl,imx8ulp-lpuart", lpuart32_imx_early_console_setup); 2768 OF_EARLYCON_DECLARE(lpuart32, "fsl,imx8qxp-lpuart", lpuart32_imx_early_console_setup); 2769 OF_EARLYCON_DECLARE(lpuart32, "fsl,imxrt1050-lpuart", lpuart32_imx_early_console_setup); 2770 EARLYCON_DECLARE(lpuart, lpuart_early_console_setup); 2771 EARLYCON_DECLARE(lpuart32, lpuart32_early_console_setup); 2772 2773 #define LPUART_CONSOLE (&lpuart_console) 2774 #define LPUART32_CONSOLE (&lpuart32_console) 2775 #else 2776 #define LPUART_CONSOLE NULL 2777 #define LPUART32_CONSOLE NULL 2778 #endif 2779 2780 static struct uart_driver lpuart_reg = { 2781 .owner = THIS_MODULE, 2782 .driver_name = DRIVER_NAME, 2783 .dev_name = DEV_NAME, 2784 .nr = ARRAY_SIZE(lpuart_ports), 2785 .cons = LPUART_CONSOLE, 2786 }; 2787 2788 static const struct serial_rs485 lpuart_rs485_supported = { 2789 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND, 2790 /* delay_rts_* and RX_DURING_TX are not supported */ 2791 }; 2792 2793 static int lpuart_global_reset(struct lpuart_port *sport) 2794 { 2795 struct uart_port *port = &sport->port; 2796 void __iomem *global_addr; 2797 unsigned long ctrl, bd; 2798 unsigned int val = 0; 2799 int ret; 2800 2801 ret = clk_prepare_enable(sport->ipg_clk); 2802 if (ret) { 2803 dev_err(sport->port.dev, "failed to enable uart ipg clk: %d\n", ret); 2804 return ret; 2805 } 2806 2807 if (is_imx7ulp_lpuart(sport) || is_imx8ulp_lpuart(sport) || is_imx8qxp_lpuart(sport)) { 2808 /* 2809 * If the transmitter is used by earlycon, wait for transmit engine to 2810 * complete and then reset. 2811 */ 2812 ctrl = lpuart32_read(port, UARTCTRL); 2813 if (ctrl & UARTCTRL_TE) { 2814 bd = lpuart32_read(&sport->port, UARTBAUD); 2815 if (read_poll_timeout(lpuart32_tx_empty, val, val, 1, 100000, false, 2816 port)) { 2817 dev_warn(sport->port.dev, 2818 "timeout waiting for transmit engine to complete\n"); 2819 clk_disable_unprepare(sport->ipg_clk); 2820 return 0; 2821 } 2822 } 2823 2824 global_addr = port->membase + UART_GLOBAL - IMX_REG_OFF; 2825 writel(UART_GLOBAL_RST, global_addr); 2826 usleep_range(GLOBAL_RST_MIN_US, GLOBAL_RST_MAX_US); 2827 writel(0, global_addr); 2828 usleep_range(GLOBAL_RST_MIN_US, GLOBAL_RST_MAX_US); 2829 2830 /* Recover the transmitter for earlycon. */ 2831 if (ctrl & UARTCTRL_TE) { 2832 lpuart32_write(port, bd, UARTBAUD); 2833 lpuart32_write(port, ctrl, UARTCTRL); 2834 } 2835 } 2836 2837 clk_disable_unprepare(sport->ipg_clk); 2838 return 0; 2839 } 2840 2841 static int lpuart_probe(struct platform_device *pdev) 2842 { 2843 const struct lpuart_soc_data *sdata = of_device_get_match_data(&pdev->dev); 2844 struct device_node *np = pdev->dev.of_node; 2845 struct lpuart_port *sport; 2846 struct resource *res; 2847 irq_handler_t handler; 2848 int ret; 2849 2850 sport = devm_kzalloc(&pdev->dev, sizeof(*sport), GFP_KERNEL); 2851 if (!sport) 2852 return -ENOMEM; 2853 2854 sport->port.membase = devm_platform_get_and_ioremap_resource(pdev, 0, &res); 2855 if (IS_ERR(sport->port.membase)) 2856 return PTR_ERR(sport->port.membase); 2857 2858 sport->port.membase += sdata->reg_off; 2859 sport->port.mapbase = res->start + sdata->reg_off; 2860 sport->port.dev = &pdev->dev; 2861 sport->port.type = PORT_LPUART; 2862 sport->devtype = sdata->devtype; 2863 sport->rx_watermark = sdata->rx_watermark; 2864 sport->dma_idle_int = is_imx7ulp_lpuart(sport) || is_imx8ulp_lpuart(sport) || 2865 is_imx8qxp_lpuart(sport); 2866 ret = platform_get_irq(pdev, 0); 2867 if (ret < 0) 2868 return ret; 2869 sport->port.irq = ret; 2870 sport->port.iotype = sdata->iotype; 2871 if (lpuart_is_32(sport)) 2872 sport->port.ops = &lpuart32_pops; 2873 else 2874 sport->port.ops = &lpuart_pops; 2875 sport->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_FSL_LPUART_CONSOLE); 2876 sport->port.flags = UPF_BOOT_AUTOCONF; 2877 2878 if (lpuart_is_32(sport)) 2879 sport->port.rs485_config = lpuart32_config_rs485; 2880 else 2881 sport->port.rs485_config = lpuart_config_rs485; 2882 sport->port.rs485_supported = lpuart_rs485_supported; 2883 2884 sport->ipg_clk = devm_clk_get(&pdev->dev, "ipg"); 2885 if (IS_ERR(sport->ipg_clk)) { 2886 ret = PTR_ERR(sport->ipg_clk); 2887 dev_err(&pdev->dev, "failed to get uart ipg clk: %d\n", ret); 2888 return ret; 2889 } 2890 2891 sport->baud_clk = NULL; 2892 if (is_imx8qxp_lpuart(sport)) { 2893 sport->baud_clk = devm_clk_get(&pdev->dev, "baud"); 2894 if (IS_ERR(sport->baud_clk)) { 2895 ret = PTR_ERR(sport->baud_clk); 2896 dev_err(&pdev->dev, "failed to get uart baud clk: %d\n", ret); 2897 return ret; 2898 } 2899 } 2900 2901 ret = of_alias_get_id(np, "serial"); 2902 if (ret < 0) { 2903 dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret); 2904 return ret; 2905 } 2906 if (ret >= ARRAY_SIZE(lpuart_ports)) { 2907 dev_err(&pdev->dev, "serial%d out of range\n", ret); 2908 return -EINVAL; 2909 } 2910 sport->port.line = ret; 2911 2912 ret = lpuart_enable_clks(sport); 2913 if (ret) 2914 return ret; 2915 sport->port.uartclk = lpuart_get_baud_clk_rate(sport); 2916 2917 lpuart_ports[sport->port.line] = sport; 2918 2919 platform_set_drvdata(pdev, &sport->port); 2920 2921 if (lpuart_is_32(sport)) { 2922 lpuart_reg.cons = LPUART32_CONSOLE; 2923 handler = lpuart32_int; 2924 } else { 2925 lpuart_reg.cons = LPUART_CONSOLE; 2926 handler = lpuart_int; 2927 } 2928 2929 pm_runtime_use_autosuspend(&pdev->dev); 2930 pm_runtime_set_autosuspend_delay(&pdev->dev, UART_AUTOSUSPEND_TIMEOUT); 2931 pm_runtime_set_active(&pdev->dev); 2932 pm_runtime_enable(&pdev->dev); 2933 2934 ret = lpuart_global_reset(sport); 2935 if (ret) 2936 goto failed_reset; 2937 2938 ret = uart_get_rs485_mode(&sport->port); 2939 if (ret) 2940 goto failed_get_rs485; 2941 2942 ret = uart_add_one_port(&lpuart_reg, &sport->port); 2943 if (ret) 2944 goto failed_attach_port; 2945 2946 ret = devm_request_irq(&pdev->dev, sport->port.irq, handler, 0, 2947 DRIVER_NAME, sport); 2948 if (ret) 2949 goto failed_irq_request; 2950 2951 return 0; 2952 2953 failed_irq_request: 2954 uart_remove_one_port(&lpuart_reg, &sport->port); 2955 failed_attach_port: 2956 failed_get_rs485: 2957 failed_reset: 2958 pm_runtime_disable(&pdev->dev); 2959 pm_runtime_set_suspended(&pdev->dev); 2960 pm_runtime_dont_use_autosuspend(&pdev->dev); 2961 lpuart_disable_clks(sport); 2962 return ret; 2963 } 2964 2965 static void lpuart_remove(struct platform_device *pdev) 2966 { 2967 struct lpuart_port *sport = platform_get_drvdata(pdev); 2968 2969 uart_remove_one_port(&lpuart_reg, &sport->port); 2970 2971 lpuart_disable_clks(sport); 2972 2973 if (sport->dma_tx_chan) 2974 dma_release_channel(sport->dma_tx_chan); 2975 2976 if (sport->dma_rx_chan) 2977 dma_release_channel(sport->dma_rx_chan); 2978 2979 pm_runtime_disable(&pdev->dev); 2980 pm_runtime_set_suspended(&pdev->dev); 2981 pm_runtime_dont_use_autosuspend(&pdev->dev); 2982 } 2983 2984 static int lpuart_runtime_suspend(struct device *dev) 2985 { 2986 struct platform_device *pdev = to_platform_device(dev); 2987 struct lpuart_port *sport = platform_get_drvdata(pdev); 2988 2989 lpuart_disable_clks(sport); 2990 2991 return 0; 2992 }; 2993 2994 static int lpuart_runtime_resume(struct device *dev) 2995 { 2996 struct platform_device *pdev = to_platform_device(dev); 2997 struct lpuart_port *sport = platform_get_drvdata(pdev); 2998 2999 return lpuart_enable_clks(sport); 3000 }; 3001 3002 static void serial_lpuart_enable_wakeup(struct lpuart_port *sport, bool on) 3003 { 3004 unsigned int val, baud; 3005 3006 if (lpuart_is_32(sport)) { 3007 val = lpuart32_read(&sport->port, UARTCTRL); 3008 baud = lpuart32_read(&sport->port, UARTBAUD); 3009 if (on) { 3010 /* set rx_watermark to 0 in wakeup source mode */ 3011 lpuart32_write(&sport->port, 0, UARTWATER); 3012 val |= UARTCTRL_RIE; 3013 /* clear RXEDGIF flag before enable RXEDGIE interrupt */ 3014 lpuart32_write(&sport->port, UARTSTAT_RXEDGIF, UARTSTAT); 3015 baud |= UARTBAUD_RXEDGIE; 3016 } else { 3017 val &= ~UARTCTRL_RIE; 3018 baud &= ~UARTBAUD_RXEDGIE; 3019 } 3020 lpuart32_write(&sport->port, val, UARTCTRL); 3021 lpuart32_write(&sport->port, baud, UARTBAUD); 3022 } else { 3023 val = readb(sport->port.membase + UARTCR2); 3024 if (on) 3025 val |= UARTCR2_RIE; 3026 else 3027 val &= ~UARTCR2_RIE; 3028 writeb(val, sport->port.membase + UARTCR2); 3029 } 3030 } 3031 3032 static bool lpuart_uport_is_active(struct lpuart_port *sport) 3033 { 3034 struct tty_port *port = &sport->port.state->port; 3035 struct tty_struct *tty; 3036 struct device *tty_dev; 3037 int may_wake = 0; 3038 3039 tty = tty_port_tty_get(port); 3040 if (tty) { 3041 tty_dev = tty->dev; 3042 may_wake = tty_dev && device_may_wakeup(tty_dev); 3043 tty_kref_put(tty); 3044 } 3045 3046 if ((tty_port_initialized(port) && may_wake) || 3047 (!console_suspend_enabled && uart_console(&sport->port))) 3048 return true; 3049 3050 return false; 3051 } 3052 3053 static int lpuart_suspend_noirq(struct device *dev) 3054 { 3055 struct lpuart_port *sport = dev_get_drvdata(dev); 3056 bool irq_wake = irqd_is_wakeup_set(irq_get_irq_data(sport->port.irq)); 3057 3058 if (lpuart_uport_is_active(sport)) 3059 serial_lpuart_enable_wakeup(sport, !!irq_wake); 3060 3061 pinctrl_pm_select_sleep_state(dev); 3062 3063 return 0; 3064 } 3065 3066 static int lpuart_resume_noirq(struct device *dev) 3067 { 3068 struct lpuart_port *sport = dev_get_drvdata(dev); 3069 unsigned int val; 3070 3071 pinctrl_pm_select_default_state(dev); 3072 3073 if (lpuart_uport_is_active(sport)) { 3074 serial_lpuart_enable_wakeup(sport, false); 3075 3076 /* clear the wakeup flags */ 3077 if (lpuart_is_32(sport)) { 3078 val = lpuart32_read(&sport->port, UARTSTAT); 3079 lpuart32_write(&sport->port, val, UARTSTAT); 3080 } 3081 } 3082 3083 return 0; 3084 } 3085 3086 static int lpuart_suspend(struct device *dev) 3087 { 3088 struct lpuart_port *sport = dev_get_drvdata(dev); 3089 unsigned long temp, flags; 3090 3091 uart_suspend_port(&lpuart_reg, &sport->port); 3092 3093 if (lpuart_uport_is_active(sport)) { 3094 uart_port_lock_irqsave(&sport->port, &flags); 3095 if (lpuart_is_32(sport)) { 3096 /* disable Rx/Tx and interrupts */ 3097 temp = lpuart32_read(&sport->port, UARTCTRL); 3098 temp &= ~(UARTCTRL_TE | UARTCTRL_TIE | UARTCTRL_TCIE); 3099 lpuart32_write(&sport->port, temp, UARTCTRL); 3100 } else { 3101 /* disable Rx/Tx and interrupts */ 3102 temp = readb(sport->port.membase + UARTCR2); 3103 temp &= ~(UARTCR2_TE | UARTCR2_TIE | UARTCR2_TCIE); 3104 writeb(temp, sport->port.membase + UARTCR2); 3105 } 3106 uart_port_unlock_irqrestore(&sport->port, flags); 3107 3108 if (sport->lpuart_dma_rx_use) { 3109 /* 3110 * EDMA driver during suspend will forcefully release any 3111 * non-idle DMA channels. If port wakeup is enabled or if port 3112 * is console port or 'no_console_suspend' is set the Rx DMA 3113 * cannot resume as expected, hence gracefully release the 3114 * Rx DMA path before suspend and start Rx DMA path on resume. 3115 */ 3116 lpuart_dma_rx_free(&sport->port); 3117 3118 /* Disable Rx DMA to use UART port as wakeup source */ 3119 uart_port_lock_irqsave(&sport->port, &flags); 3120 if (lpuart_is_32(sport)) { 3121 temp = lpuart32_read(&sport->port, UARTBAUD); 3122 lpuart32_write(&sport->port, temp & ~UARTBAUD_RDMAE, 3123 UARTBAUD); 3124 } else { 3125 writeb(readb(sport->port.membase + UARTCR5) & 3126 ~UARTCR5_RDMAS, sport->port.membase + UARTCR5); 3127 } 3128 uart_port_unlock_irqrestore(&sport->port, flags); 3129 } 3130 3131 if (sport->lpuart_dma_tx_use) { 3132 uart_port_lock_irqsave(&sport->port, &flags); 3133 if (lpuart_is_32(sport)) { 3134 temp = lpuart32_read(&sport->port, UARTBAUD); 3135 temp &= ~UARTBAUD_TDMAE; 3136 lpuart32_write(&sport->port, temp, UARTBAUD); 3137 } else { 3138 temp = readb(sport->port.membase + UARTCR5); 3139 temp &= ~UARTCR5_TDMAS; 3140 writeb(temp, sport->port.membase + UARTCR5); 3141 } 3142 uart_port_unlock_irqrestore(&sport->port, flags); 3143 sport->dma_tx_in_progress = false; 3144 dmaengine_terminate_sync(sport->dma_tx_chan); 3145 } 3146 } else if (pm_runtime_active(sport->port.dev)) { 3147 lpuart_disable_clks(sport); 3148 pm_runtime_disable(sport->port.dev); 3149 pm_runtime_set_suspended(sport->port.dev); 3150 } 3151 3152 return 0; 3153 } 3154 3155 static void lpuart_console_fixup(struct lpuart_port *sport) 3156 { 3157 struct tty_port *port = &sport->port.state->port; 3158 struct uart_port *uport = &sport->port; 3159 struct ktermios termios; 3160 3161 /* i.MX7ULP enter VLLS mode that lpuart module power off and registers 3162 * all lost no matter the port is wakeup source. 3163 * For console port, console baud rate setting lost and print messy 3164 * log when enable the console port as wakeup source. To avoid the 3165 * issue happen, user should not enable uart port as wakeup source 3166 * in VLLS mode, or restore console setting here. 3167 */ 3168 if (is_imx7ulp_lpuart(sport) && lpuart_uport_is_active(sport) && 3169 console_suspend_enabled && uart_console(&sport->port)) { 3170 3171 mutex_lock(&port->mutex); 3172 memset(&termios, 0, sizeof(struct ktermios)); 3173 termios.c_cflag = uport->cons->cflag; 3174 if (port->tty && termios.c_cflag == 0) 3175 termios = port->tty->termios; 3176 uport->ops->set_termios(uport, &termios, NULL); 3177 mutex_unlock(&port->mutex); 3178 } 3179 } 3180 3181 static int lpuart_resume(struct device *dev) 3182 { 3183 struct lpuart_port *sport = dev_get_drvdata(dev); 3184 int ret; 3185 3186 if (lpuart_uport_is_active(sport)) { 3187 if (lpuart_is_32(sport)) 3188 lpuart32_hw_setup(sport); 3189 else 3190 lpuart_hw_setup(sport); 3191 } else if (pm_runtime_active(sport->port.dev)) { 3192 ret = lpuart_enable_clks(sport); 3193 if (ret) 3194 return ret; 3195 pm_runtime_set_active(sport->port.dev); 3196 pm_runtime_enable(sport->port.dev); 3197 } 3198 3199 lpuart_console_fixup(sport); 3200 uart_resume_port(&lpuart_reg, &sport->port); 3201 3202 return 0; 3203 } 3204 3205 static const struct dev_pm_ops lpuart_pm_ops = { 3206 RUNTIME_PM_OPS(lpuart_runtime_suspend, 3207 lpuart_runtime_resume, NULL) 3208 NOIRQ_SYSTEM_SLEEP_PM_OPS(lpuart_suspend_noirq, 3209 lpuart_resume_noirq) 3210 SYSTEM_SLEEP_PM_OPS(lpuart_suspend, lpuart_resume) 3211 }; 3212 3213 static struct platform_driver lpuart_driver = { 3214 .probe = lpuart_probe, 3215 .remove_new = lpuart_remove, 3216 .driver = { 3217 .name = "fsl-lpuart", 3218 .of_match_table = lpuart_dt_ids, 3219 .pm = pm_ptr(&lpuart_pm_ops), 3220 }, 3221 }; 3222 3223 static int __init lpuart_serial_init(void) 3224 { 3225 int ret = uart_register_driver(&lpuart_reg); 3226 3227 if (ret) 3228 return ret; 3229 3230 ret = platform_driver_register(&lpuart_driver); 3231 if (ret) 3232 uart_unregister_driver(&lpuart_reg); 3233 3234 return ret; 3235 } 3236 3237 static void __exit lpuart_serial_exit(void) 3238 { 3239 platform_driver_unregister(&lpuart_driver); 3240 uart_unregister_driver(&lpuart_reg); 3241 } 3242 3243 module_init(lpuart_serial_init); 3244 module_exit(lpuart_serial_exit); 3245 3246 MODULE_DESCRIPTION("Freescale lpuart serial port driver"); 3247 MODULE_LICENSE("GPL v2"); 3248