1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Driver for Atmel AT91 Serial ports 4 * Copyright (C) 2003 Rick Bronson 5 * 6 * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd. 7 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. 8 * 9 * DMA support added by Chip Coldwell. 10 */ 11 #include <linux/circ_buf.h> 12 #include <linux/tty.h> 13 #include <linux/ioport.h> 14 #include <linux/slab.h> 15 #include <linux/init.h> 16 #include <linux/serial.h> 17 #include <linux/clk.h> 18 #include <linux/clk-provider.h> 19 #include <linux/console.h> 20 #include <linux/sysrq.h> 21 #include <linux/tty_flip.h> 22 #include <linux/platform_device.h> 23 #include <linux/of.h> 24 #include <linux/dma-mapping.h> 25 #include <linux/dmaengine.h> 26 #include <linux/atmel_pdc.h> 27 #include <linux/uaccess.h> 28 #include <linux/platform_data/atmel.h> 29 #include <linux/timer.h> 30 #include <linux/err.h> 31 #include <linux/irq.h> 32 #include <linux/suspend.h> 33 #include <linux/mm.h> 34 #include <linux/io.h> 35 36 #include <asm/div64.h> 37 #include <asm/ioctls.h> 38 39 #define PDC_BUFFER_SIZE 512 40 /* Revisit: We should calculate this based on the actual port settings */ 41 #define PDC_RX_TIMEOUT (3 * 10) /* 3 bytes */ 42 43 /* The minium number of data FIFOs should be able to contain */ 44 #define ATMEL_MIN_FIFO_SIZE 8 45 /* 46 * These two offsets are substracted from the RX FIFO size to define the RTS 47 * high and low thresholds 48 */ 49 #define ATMEL_RTS_HIGH_OFFSET 16 50 #define ATMEL_RTS_LOW_OFFSET 20 51 52 #include <linux/serial_core.h> 53 54 #include "serial_mctrl_gpio.h" 55 #include "atmel_serial.h" 56 57 static void atmel_start_rx(struct uart_port *port); 58 static void atmel_stop_rx(struct uart_port *port); 59 60 #ifdef CONFIG_SERIAL_ATMEL_TTYAT 61 62 /* Use device name ttyAT, major 204 and minor 154-169. This is necessary if we 63 * should coexist with the 8250 driver, such as if we have an external 16C550 64 * UART. */ 65 #define SERIAL_ATMEL_MAJOR 204 66 #define MINOR_START 154 67 #define ATMEL_DEVICENAME "ttyAT" 68 69 #else 70 71 /* Use device name ttyS, major 4, minor 64-68. This is the usual serial port 72 * name, but it is legally reserved for the 8250 driver. */ 73 #define SERIAL_ATMEL_MAJOR TTY_MAJOR 74 #define MINOR_START 64 75 #define ATMEL_DEVICENAME "ttyS" 76 77 #endif 78 79 #define ATMEL_ISR_PASS_LIMIT 256 80 81 struct atmel_dma_buffer { 82 unsigned char *buf; 83 dma_addr_t dma_addr; 84 unsigned int dma_size; 85 unsigned int ofs; 86 }; 87 88 struct atmel_uart_char { 89 u16 status; 90 u16 ch; 91 }; 92 93 /* 94 * Be careful, the real size of the ring buffer is 95 * sizeof(atmel_uart_char) * ATMEL_SERIAL_RINGSIZE. It means that ring buffer 96 * can contain up to 1024 characters in PIO mode and up to 4096 characters in 97 * DMA mode. 98 */ 99 #define ATMEL_SERIAL_RINGSIZE 1024 100 #define ATMEL_SERIAL_RX_SIZE array_size(sizeof(struct atmel_uart_char), \ 101 ATMEL_SERIAL_RINGSIZE) 102 103 /* 104 * at91: 6 USARTs and one DBGU port (SAM9260) 105 * samx7: 3 USARTs and 5 UARTs 106 */ 107 #define ATMEL_MAX_UART 8 108 109 /* 110 * We wrap our port structure around the generic uart_port. 111 */ 112 struct atmel_uart_port { 113 struct uart_port uart; /* uart */ 114 struct clk *clk; /* uart clock */ 115 struct clk *gclk; /* uart generic clock */ 116 int may_wakeup; /* cached value of device_may_wakeup for times we need to disable it */ 117 u32 backup_imr; /* IMR saved during suspend */ 118 int break_active; /* break being received */ 119 120 bool use_dma_rx; /* enable DMA receiver */ 121 bool use_pdc_rx; /* enable PDC receiver */ 122 short pdc_rx_idx; /* current PDC RX buffer */ 123 struct atmel_dma_buffer pdc_rx[2]; /* PDC receier */ 124 125 bool use_dma_tx; /* enable DMA transmitter */ 126 bool use_pdc_tx; /* enable PDC transmitter */ 127 struct atmel_dma_buffer pdc_tx; /* PDC transmitter */ 128 129 spinlock_t lock_tx; /* port lock */ 130 spinlock_t lock_rx; /* port lock */ 131 struct dma_chan *chan_tx; 132 struct dma_chan *chan_rx; 133 struct dma_async_tx_descriptor *desc_tx; 134 struct dma_async_tx_descriptor *desc_rx; 135 dma_cookie_t cookie_tx; 136 dma_cookie_t cookie_rx; 137 dma_addr_t tx_phys; 138 dma_addr_t rx_phys; 139 struct tasklet_struct tasklet_rx; 140 struct tasklet_struct tasklet_tx; 141 atomic_t tasklet_shutdown; 142 unsigned int irq_status_prev; 143 unsigned int tx_len; 144 145 struct circ_buf rx_ring; 146 147 struct mctrl_gpios *gpios; 148 u32 backup_mode; /* MR saved during iso7816 operations */ 149 u32 backup_brgr; /* BRGR saved during iso7816 operations */ 150 unsigned int tx_done_mask; 151 u32 fifo_size; 152 u32 rts_high; 153 u32 rts_low; 154 bool ms_irq_enabled; 155 u32 rtor; /* address of receiver timeout register if it exists */ 156 bool is_usart; 157 bool has_frac_baudrate; 158 bool has_hw_timer; 159 struct timer_list uart_timer; 160 161 bool tx_stopped; 162 bool suspended; 163 unsigned int pending; 164 unsigned int pending_status; 165 spinlock_t lock_suspended; 166 167 bool hd_start_rx; /* can start RX during half-duplex operation */ 168 169 /* ISO7816 */ 170 unsigned int fidi_min; 171 unsigned int fidi_max; 172 173 struct { 174 u32 cr; 175 u32 mr; 176 u32 imr; 177 u32 brgr; 178 u32 rtor; 179 u32 ttgr; 180 u32 fmr; 181 u32 fimr; 182 } cache; 183 184 int (*prepare_rx)(struct uart_port *port); 185 int (*prepare_tx)(struct uart_port *port); 186 void (*schedule_rx)(struct uart_port *port); 187 void (*schedule_tx)(struct uart_port *port); 188 void (*release_rx)(struct uart_port *port); 189 void (*release_tx)(struct uart_port *port); 190 }; 191 192 static struct atmel_uart_port atmel_ports[ATMEL_MAX_UART]; 193 static DECLARE_BITMAP(atmel_ports_in_use, ATMEL_MAX_UART); 194 195 #if defined(CONFIG_OF) 196 static const struct of_device_id atmel_serial_dt_ids[] = { 197 { .compatible = "atmel,at91rm9200-usart-serial" }, 198 { /* sentinel */ } 199 }; 200 #endif 201 202 static inline struct atmel_uart_port * 203 to_atmel_uart_port(struct uart_port *uart) 204 { 205 return container_of(uart, struct atmel_uart_port, uart); 206 } 207 208 static inline u32 atmel_uart_readl(struct uart_port *port, u32 reg) 209 { 210 return __raw_readl(port->membase + reg); 211 } 212 213 static inline void atmel_uart_writel(struct uart_port *port, u32 reg, u32 value) 214 { 215 __raw_writel(value, port->membase + reg); 216 } 217 218 static inline u8 atmel_uart_read_char(struct uart_port *port) 219 { 220 return __raw_readb(port->membase + ATMEL_US_RHR); 221 } 222 223 static inline void atmel_uart_write_char(struct uart_port *port, u8 value) 224 { 225 __raw_writeb(value, port->membase + ATMEL_US_THR); 226 } 227 228 static inline int atmel_uart_is_half_duplex(struct uart_port *port) 229 { 230 return ((port->rs485.flags & SER_RS485_ENABLED) && 231 !(port->rs485.flags & SER_RS485_RX_DURING_TX)) || 232 (port->iso7816.flags & SER_ISO7816_ENABLED); 233 } 234 235 static inline int atmel_error_rate(int desired_value, int actual_value) 236 { 237 return 100 - (desired_value * 100) / actual_value; 238 } 239 240 #ifdef CONFIG_SERIAL_ATMEL_PDC 241 static bool atmel_use_pdc_rx(struct uart_port *port) 242 { 243 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 244 245 return atmel_port->use_pdc_rx; 246 } 247 248 static bool atmel_use_pdc_tx(struct uart_port *port) 249 { 250 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 251 252 return atmel_port->use_pdc_tx; 253 } 254 #else 255 static bool atmel_use_pdc_rx(struct uart_port *port) 256 { 257 return false; 258 } 259 260 static bool atmel_use_pdc_tx(struct uart_port *port) 261 { 262 return false; 263 } 264 #endif 265 266 static bool atmel_use_dma_tx(struct uart_port *port) 267 { 268 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 269 270 return atmel_port->use_dma_tx; 271 } 272 273 static bool atmel_use_dma_rx(struct uart_port *port) 274 { 275 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 276 277 return atmel_port->use_dma_rx; 278 } 279 280 static bool atmel_use_fifo(struct uart_port *port) 281 { 282 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 283 284 return atmel_port->fifo_size; 285 } 286 287 static void atmel_tasklet_schedule(struct atmel_uart_port *atmel_port, 288 struct tasklet_struct *t) 289 { 290 if (!atomic_read(&atmel_port->tasklet_shutdown)) 291 tasklet_schedule(t); 292 } 293 294 /* Enable or disable the rs485 support */ 295 static int atmel_config_rs485(struct uart_port *port, struct ktermios *termios, 296 struct serial_rs485 *rs485conf) 297 { 298 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 299 unsigned int mode; 300 301 /* Disable interrupts */ 302 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask); 303 304 mode = atmel_uart_readl(port, ATMEL_US_MR); 305 306 if (rs485conf->flags & SER_RS485_ENABLED) { 307 dev_dbg(port->dev, "Setting UART to RS485\n"); 308 if (rs485conf->flags & SER_RS485_RX_DURING_TX) 309 atmel_port->tx_done_mask = ATMEL_US_TXRDY; 310 else 311 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY; 312 313 atmel_uart_writel(port, ATMEL_US_TTGR, 314 rs485conf->delay_rts_after_send); 315 mode &= ~ATMEL_US_USMODE; 316 mode |= ATMEL_US_USMODE_RS485; 317 } else { 318 dev_dbg(port->dev, "Setting UART to RS232\n"); 319 if (atmel_use_pdc_tx(port)) 320 atmel_port->tx_done_mask = ATMEL_US_ENDTX | 321 ATMEL_US_TXBUFE; 322 else 323 atmel_port->tx_done_mask = ATMEL_US_TXRDY; 324 } 325 atmel_uart_writel(port, ATMEL_US_MR, mode); 326 327 /* Enable interrupts */ 328 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask); 329 330 return 0; 331 } 332 333 static unsigned int atmel_calc_cd(struct uart_port *port, 334 struct serial_iso7816 *iso7816conf) 335 { 336 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 337 unsigned int cd; 338 u64 mck_rate; 339 340 mck_rate = (u64)clk_get_rate(atmel_port->clk); 341 do_div(mck_rate, iso7816conf->clk); 342 cd = mck_rate; 343 return cd; 344 } 345 346 static unsigned int atmel_calc_fidi(struct uart_port *port, 347 struct serial_iso7816 *iso7816conf) 348 { 349 u64 fidi = 0; 350 351 if (iso7816conf->sc_fi && iso7816conf->sc_di) { 352 fidi = (u64)iso7816conf->sc_fi; 353 do_div(fidi, iso7816conf->sc_di); 354 } 355 return (u32)fidi; 356 } 357 358 /* Enable or disable the iso7816 support */ 359 /* Called with interrupts disabled */ 360 static int atmel_config_iso7816(struct uart_port *port, 361 struct serial_iso7816 *iso7816conf) 362 { 363 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 364 unsigned int mode; 365 unsigned int cd, fidi; 366 int ret = 0; 367 368 /* Disable interrupts */ 369 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask); 370 371 mode = atmel_uart_readl(port, ATMEL_US_MR); 372 373 if (iso7816conf->flags & SER_ISO7816_ENABLED) { 374 mode &= ~ATMEL_US_USMODE; 375 376 if (iso7816conf->tg > 255) { 377 dev_err(port->dev, "ISO7816: Timeguard exceeding 255\n"); 378 memset(iso7816conf, 0, sizeof(struct serial_iso7816)); 379 ret = -EINVAL; 380 goto err_out; 381 } 382 383 if ((iso7816conf->flags & SER_ISO7816_T_PARAM) 384 == SER_ISO7816_T(0)) { 385 mode |= ATMEL_US_USMODE_ISO7816_T0 | ATMEL_US_DSNACK; 386 } else if ((iso7816conf->flags & SER_ISO7816_T_PARAM) 387 == SER_ISO7816_T(1)) { 388 mode |= ATMEL_US_USMODE_ISO7816_T1 | ATMEL_US_INACK; 389 } else { 390 dev_err(port->dev, "ISO7816: Type not supported\n"); 391 memset(iso7816conf, 0, sizeof(struct serial_iso7816)); 392 ret = -EINVAL; 393 goto err_out; 394 } 395 396 mode &= ~(ATMEL_US_USCLKS | ATMEL_US_NBSTOP | ATMEL_US_PAR); 397 398 /* select mck clock, and output */ 399 mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO; 400 /* set parity for normal/inverse mode + max iterations */ 401 mode |= ATMEL_US_PAR_EVEN | ATMEL_US_NBSTOP_1 | ATMEL_US_MAX_ITER(3); 402 403 cd = atmel_calc_cd(port, iso7816conf); 404 fidi = atmel_calc_fidi(port, iso7816conf); 405 if (fidi == 0) { 406 dev_warn(port->dev, "ISO7816 fidi = 0, Generator generates no signal\n"); 407 } else if (fidi < atmel_port->fidi_min 408 || fidi > atmel_port->fidi_max) { 409 dev_err(port->dev, "ISO7816 fidi = %u, value not supported\n", fidi); 410 memset(iso7816conf, 0, sizeof(struct serial_iso7816)); 411 ret = -EINVAL; 412 goto err_out; 413 } 414 415 if (!(port->iso7816.flags & SER_ISO7816_ENABLED)) { 416 /* port not yet in iso7816 mode: store configuration */ 417 atmel_port->backup_mode = atmel_uart_readl(port, ATMEL_US_MR); 418 atmel_port->backup_brgr = atmel_uart_readl(port, ATMEL_US_BRGR); 419 } 420 421 atmel_uart_writel(port, ATMEL_US_TTGR, iso7816conf->tg); 422 atmel_uart_writel(port, ATMEL_US_BRGR, cd); 423 atmel_uart_writel(port, ATMEL_US_FIDI, fidi); 424 425 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXEN); 426 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY | ATMEL_US_NACK | ATMEL_US_ITERATION; 427 } else { 428 dev_dbg(port->dev, "Setting UART back to RS232\n"); 429 /* back to last RS232 settings */ 430 mode = atmel_port->backup_mode; 431 memset(iso7816conf, 0, sizeof(struct serial_iso7816)); 432 atmel_uart_writel(port, ATMEL_US_TTGR, 0); 433 atmel_uart_writel(port, ATMEL_US_BRGR, atmel_port->backup_brgr); 434 atmel_uart_writel(port, ATMEL_US_FIDI, 0x174); 435 436 if (atmel_use_pdc_tx(port)) 437 atmel_port->tx_done_mask = ATMEL_US_ENDTX | 438 ATMEL_US_TXBUFE; 439 else 440 atmel_port->tx_done_mask = ATMEL_US_TXRDY; 441 } 442 443 port->iso7816 = *iso7816conf; 444 445 atmel_uart_writel(port, ATMEL_US_MR, mode); 446 447 err_out: 448 /* Enable interrupts */ 449 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask); 450 451 return ret; 452 } 453 454 /* 455 * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty. 456 */ 457 static u_int atmel_tx_empty(struct uart_port *port) 458 { 459 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 460 461 if (atmel_port->tx_stopped) 462 return TIOCSER_TEMT; 463 return (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXEMPTY) ? 464 TIOCSER_TEMT : 465 0; 466 } 467 468 /* 469 * Set state of the modem control output lines 470 */ 471 static void atmel_set_mctrl(struct uart_port *port, u_int mctrl) 472 { 473 unsigned int control = 0; 474 unsigned int mode = atmel_uart_readl(port, ATMEL_US_MR); 475 unsigned int rts_paused, rts_ready; 476 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 477 478 /* override mode to RS485 if needed, otherwise keep the current mode */ 479 if (port->rs485.flags & SER_RS485_ENABLED) { 480 atmel_uart_writel(port, ATMEL_US_TTGR, 481 port->rs485.delay_rts_after_send); 482 mode &= ~ATMEL_US_USMODE; 483 mode |= ATMEL_US_USMODE_RS485; 484 } 485 486 /* set the RTS line state according to the mode */ 487 if ((mode & ATMEL_US_USMODE) == ATMEL_US_USMODE_HWHS) { 488 /* force RTS line to high level */ 489 rts_paused = ATMEL_US_RTSEN; 490 491 /* give the control of the RTS line back to the hardware */ 492 rts_ready = ATMEL_US_RTSDIS; 493 } else { 494 /* force RTS line to high level */ 495 rts_paused = ATMEL_US_RTSDIS; 496 497 /* force RTS line to low level */ 498 rts_ready = ATMEL_US_RTSEN; 499 } 500 501 if (mctrl & TIOCM_RTS) 502 control |= rts_ready; 503 else 504 control |= rts_paused; 505 506 if (mctrl & TIOCM_DTR) 507 control |= ATMEL_US_DTREN; 508 else 509 control |= ATMEL_US_DTRDIS; 510 511 atmel_uart_writel(port, ATMEL_US_CR, control); 512 513 mctrl_gpio_set(atmel_port->gpios, mctrl); 514 515 /* Local loopback mode? */ 516 mode &= ~ATMEL_US_CHMODE; 517 if (mctrl & TIOCM_LOOP) 518 mode |= ATMEL_US_CHMODE_LOC_LOOP; 519 else 520 mode |= ATMEL_US_CHMODE_NORMAL; 521 522 atmel_uart_writel(port, ATMEL_US_MR, mode); 523 } 524 525 /* 526 * Get state of the modem control input lines 527 */ 528 static u_int atmel_get_mctrl(struct uart_port *port) 529 { 530 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 531 unsigned int ret = 0, status; 532 533 status = atmel_uart_readl(port, ATMEL_US_CSR); 534 535 /* 536 * The control signals are active low. 537 */ 538 if (!(status & ATMEL_US_DCD)) 539 ret |= TIOCM_CD; 540 if (!(status & ATMEL_US_CTS)) 541 ret |= TIOCM_CTS; 542 if (!(status & ATMEL_US_DSR)) 543 ret |= TIOCM_DSR; 544 if (!(status & ATMEL_US_RI)) 545 ret |= TIOCM_RI; 546 547 return mctrl_gpio_get(atmel_port->gpios, &ret); 548 } 549 550 /* 551 * Stop transmitting. 552 */ 553 static void atmel_stop_tx(struct uart_port *port) 554 { 555 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 556 bool is_pdc = atmel_use_pdc_tx(port); 557 bool is_dma = is_pdc || atmel_use_dma_tx(port); 558 559 if (is_pdc) { 560 /* disable PDC transmit */ 561 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS); 562 } 563 564 if (is_dma) { 565 /* 566 * Disable the transmitter. 567 * This is mandatory when DMA is used, otherwise the DMA buffer 568 * is fully transmitted. 569 */ 570 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS); 571 atmel_port->tx_stopped = true; 572 } 573 574 /* Disable interrupts */ 575 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask); 576 577 if (atmel_uart_is_half_duplex(port)) 578 if (!atomic_read(&atmel_port->tasklet_shutdown)) 579 atmel_start_rx(port); 580 } 581 582 /* 583 * Start transmitting. 584 */ 585 static void atmel_start_tx(struct uart_port *port) 586 { 587 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 588 bool is_pdc = atmel_use_pdc_tx(port); 589 bool is_dma = is_pdc || atmel_use_dma_tx(port); 590 591 if (is_pdc && (atmel_uart_readl(port, ATMEL_PDC_PTSR) 592 & ATMEL_PDC_TXTEN)) 593 /* The transmitter is already running. Yes, we 594 really need this.*/ 595 return; 596 597 if (is_dma && atmel_uart_is_half_duplex(port)) 598 atmel_stop_rx(port); 599 600 if (is_pdc) { 601 /* re-enable PDC transmit */ 602 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); 603 } 604 605 /* Enable interrupts */ 606 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask); 607 608 if (is_dma) { 609 /* re-enable the transmitter */ 610 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN); 611 atmel_port->tx_stopped = false; 612 } 613 } 614 615 /* 616 * start receiving - port is in process of being opened. 617 */ 618 static void atmel_start_rx(struct uart_port *port) 619 { 620 /* reset status and receiver */ 621 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); 622 623 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXEN); 624 625 if (atmel_use_pdc_rx(port)) { 626 /* enable PDC controller */ 627 atmel_uart_writel(port, ATMEL_US_IER, 628 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT | 629 port->read_status_mask); 630 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN); 631 } else { 632 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY); 633 } 634 } 635 636 /* 637 * Stop receiving - port is in process of being closed. 638 */ 639 static void atmel_stop_rx(struct uart_port *port) 640 { 641 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXDIS); 642 643 if (atmel_use_pdc_rx(port)) { 644 /* disable PDC receive */ 645 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS); 646 atmel_uart_writel(port, ATMEL_US_IDR, 647 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT | 648 port->read_status_mask); 649 } else { 650 atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXRDY); 651 } 652 } 653 654 /* 655 * Enable modem status interrupts 656 */ 657 static void atmel_enable_ms(struct uart_port *port) 658 { 659 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 660 uint32_t ier = 0; 661 662 /* 663 * Interrupt should not be enabled twice 664 */ 665 if (atmel_port->ms_irq_enabled) 666 return; 667 668 atmel_port->ms_irq_enabled = true; 669 670 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS)) 671 ier |= ATMEL_US_CTSIC; 672 673 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DSR)) 674 ier |= ATMEL_US_DSRIC; 675 676 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_RI)) 677 ier |= ATMEL_US_RIIC; 678 679 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DCD)) 680 ier |= ATMEL_US_DCDIC; 681 682 atmel_uart_writel(port, ATMEL_US_IER, ier); 683 684 mctrl_gpio_enable_ms(atmel_port->gpios); 685 } 686 687 /* 688 * Disable modem status interrupts 689 */ 690 static void atmel_disable_ms(struct uart_port *port) 691 { 692 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 693 uint32_t idr = 0; 694 695 /* 696 * Interrupt should not be disabled twice 697 */ 698 if (!atmel_port->ms_irq_enabled) 699 return; 700 701 atmel_port->ms_irq_enabled = false; 702 703 mctrl_gpio_disable_ms_no_sync(atmel_port->gpios); 704 705 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS)) 706 idr |= ATMEL_US_CTSIC; 707 708 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DSR)) 709 idr |= ATMEL_US_DSRIC; 710 711 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_RI)) 712 idr |= ATMEL_US_RIIC; 713 714 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DCD)) 715 idr |= ATMEL_US_DCDIC; 716 717 atmel_uart_writel(port, ATMEL_US_IDR, idr); 718 } 719 720 /* 721 * Control the transmission of a break signal 722 */ 723 static void atmel_break_ctl(struct uart_port *port, int break_state) 724 { 725 if (break_state != 0) 726 /* start break */ 727 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTBRK); 728 else 729 /* stop break */ 730 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STPBRK); 731 } 732 733 /* 734 * Stores the incoming character in the ring buffer 735 */ 736 static void 737 atmel_buffer_rx_char(struct uart_port *port, unsigned int status, 738 unsigned int ch) 739 { 740 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 741 struct circ_buf *ring = &atmel_port->rx_ring; 742 struct atmel_uart_char *c; 743 744 if (!CIRC_SPACE(ring->head, ring->tail, ATMEL_SERIAL_RINGSIZE)) 745 /* Buffer overflow, ignore char */ 746 return; 747 748 c = &((struct atmel_uart_char *)ring->buf)[ring->head]; 749 c->status = status; 750 c->ch = ch; 751 752 /* Make sure the character is stored before we update head. */ 753 smp_wmb(); 754 755 ring->head = (ring->head + 1) & (ATMEL_SERIAL_RINGSIZE - 1); 756 } 757 758 /* 759 * Deal with parity, framing and overrun errors. 760 */ 761 static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status) 762 { 763 /* clear error */ 764 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); 765 766 if (status & ATMEL_US_RXBRK) { 767 /* ignore side-effect */ 768 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME); 769 port->icount.brk++; 770 } 771 if (status & ATMEL_US_PARE) 772 port->icount.parity++; 773 if (status & ATMEL_US_FRAME) 774 port->icount.frame++; 775 if (status & ATMEL_US_OVRE) 776 port->icount.overrun++; 777 } 778 779 /* 780 * Characters received (called from interrupt handler) 781 */ 782 static void atmel_rx_chars(struct uart_port *port) 783 { 784 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 785 unsigned int status, ch; 786 787 status = atmel_uart_readl(port, ATMEL_US_CSR); 788 while (status & ATMEL_US_RXRDY) { 789 ch = atmel_uart_read_char(port); 790 791 /* 792 * note that the error handling code is 793 * out of the main execution path 794 */ 795 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME 796 | ATMEL_US_OVRE | ATMEL_US_RXBRK) 797 || atmel_port->break_active)) { 798 799 /* clear error */ 800 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); 801 802 if (status & ATMEL_US_RXBRK 803 && !atmel_port->break_active) { 804 atmel_port->break_active = 1; 805 atmel_uart_writel(port, ATMEL_US_IER, 806 ATMEL_US_RXBRK); 807 } else { 808 /* 809 * This is either the end-of-break 810 * condition or we've received at 811 * least one character without RXBRK 812 * being set. In both cases, the next 813 * RXBRK will indicate start-of-break. 814 */ 815 atmel_uart_writel(port, ATMEL_US_IDR, 816 ATMEL_US_RXBRK); 817 status &= ~ATMEL_US_RXBRK; 818 atmel_port->break_active = 0; 819 } 820 } 821 822 atmel_buffer_rx_char(port, status, ch); 823 status = atmel_uart_readl(port, ATMEL_US_CSR); 824 } 825 826 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx); 827 } 828 829 /* 830 * Transmit characters (called from tasklet with TXRDY interrupt 831 * disabled) 832 */ 833 static void atmel_tx_chars(struct uart_port *port) 834 { 835 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 836 bool pending; 837 u8 ch; 838 839 pending = uart_port_tx(port, ch, 840 atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY, 841 atmel_uart_write_char(port, ch)); 842 if (pending) { 843 /* we still have characters to transmit, so we should continue 844 * transmitting them when TX is ready, regardless of 845 * mode or duplexity 846 */ 847 atmel_port->tx_done_mask |= ATMEL_US_TXRDY; 848 849 /* Enable interrupts */ 850 atmel_uart_writel(port, ATMEL_US_IER, 851 atmel_port->tx_done_mask); 852 } else { 853 if (atmel_uart_is_half_duplex(port)) 854 atmel_port->tx_done_mask &= ~ATMEL_US_TXRDY; 855 } 856 } 857 858 static void atmel_complete_tx_dma(void *arg) 859 { 860 struct atmel_uart_port *atmel_port = arg; 861 struct uart_port *port = &atmel_port->uart; 862 struct tty_port *tport = &port->state->port; 863 struct dma_chan *chan = atmel_port->chan_tx; 864 unsigned long flags; 865 866 uart_port_lock_irqsave(port, &flags); 867 868 if (chan) 869 dmaengine_terminate_all(chan); 870 uart_xmit_advance(port, atmel_port->tx_len); 871 872 spin_lock(&atmel_port->lock_tx); 873 async_tx_ack(atmel_port->desc_tx); 874 atmel_port->cookie_tx = -EINVAL; 875 atmel_port->desc_tx = NULL; 876 spin_unlock(&atmel_port->lock_tx); 877 878 if (kfifo_len(&tport->xmit_fifo) < WAKEUP_CHARS) 879 uart_write_wakeup(port); 880 881 /* 882 * xmit is a circular buffer so, if we have just send data from the 883 * tail to the end, now we have to transmit the remaining data from the 884 * beginning to the head. 885 */ 886 if (!kfifo_is_empty(&tport->xmit_fifo)) 887 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx); 888 else if (atmel_uart_is_half_duplex(port)) { 889 /* 890 * DMA done, re-enable TXEMPTY and signal that we can stop 891 * TX and start RX for RS485 892 */ 893 atmel_port->hd_start_rx = true; 894 atmel_uart_writel(port, ATMEL_US_IER, 895 atmel_port->tx_done_mask); 896 } 897 898 uart_port_unlock_irqrestore(port, flags); 899 } 900 901 static void atmel_release_tx_dma(struct uart_port *port) 902 { 903 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 904 struct dma_chan *chan = atmel_port->chan_tx; 905 906 if (chan) { 907 dmaengine_terminate_all(chan); 908 dma_release_channel(chan); 909 dma_unmap_single(port->dev, atmel_port->tx_phys, 910 UART_XMIT_SIZE, DMA_TO_DEVICE); 911 } 912 913 atmel_port->desc_tx = NULL; 914 atmel_port->chan_tx = NULL; 915 atmel_port->cookie_tx = -EINVAL; 916 } 917 918 /* 919 * Called from tasklet with TXRDY interrupt is disabled. 920 */ 921 static void atmel_tx_dma(struct uart_port *port) 922 { 923 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 924 struct tty_port *tport = &port->state->port; 925 struct dma_chan *chan = atmel_port->chan_tx; 926 struct dma_async_tx_descriptor *desc; 927 struct scatterlist sgl[2], *sg; 928 unsigned int tx_len, tail, part1_len, part2_len, sg_len; 929 dma_addr_t phys_addr; 930 931 /* Make sure we have an idle channel */ 932 if (atmel_port->desc_tx != NULL) 933 return; 934 935 if (!kfifo_is_empty(&tport->xmit_fifo) && !uart_tx_stopped(port)) { 936 /* 937 * DMA is idle now. 938 * Port xmit buffer is already mapped, 939 * and it is one page... Just adjust 940 * offsets and lengths. Since it is a circular buffer, 941 * we have to transmit till the end, and then the rest. 942 * Take the port lock to get a 943 * consistent xmit buffer state. 944 */ 945 tx_len = kfifo_out_linear(&tport->xmit_fifo, &tail, 946 UART_XMIT_SIZE); 947 948 if (atmel_port->fifo_size) { 949 /* multi data mode */ 950 part1_len = (tx_len & ~0x3); /* DWORD access */ 951 part2_len = (tx_len & 0x3); /* BYTE access */ 952 } else { 953 /* single data (legacy) mode */ 954 part1_len = 0; 955 part2_len = tx_len; /* BYTE access only */ 956 } 957 958 sg_init_table(sgl, 2); 959 sg_len = 0; 960 phys_addr = atmel_port->tx_phys + tail; 961 if (part1_len) { 962 sg = &sgl[sg_len++]; 963 sg_dma_address(sg) = phys_addr; 964 sg_dma_len(sg) = part1_len; 965 966 phys_addr += part1_len; 967 } 968 969 if (part2_len) { 970 sg = &sgl[sg_len++]; 971 sg_dma_address(sg) = phys_addr; 972 sg_dma_len(sg) = part2_len; 973 } 974 975 /* 976 * save tx_len so atmel_complete_tx_dma() will increase 977 * tail correctly 978 */ 979 atmel_port->tx_len = tx_len; 980 981 desc = dmaengine_prep_slave_sg(chan, 982 sgl, 983 sg_len, 984 DMA_MEM_TO_DEV, 985 DMA_PREP_INTERRUPT | 986 DMA_CTRL_ACK); 987 if (!desc) { 988 dev_err(port->dev, "Failed to send via dma!\n"); 989 return; 990 } 991 992 dma_sync_single_for_device(port->dev, atmel_port->tx_phys, 993 UART_XMIT_SIZE, DMA_TO_DEVICE); 994 995 atmel_port->desc_tx = desc; 996 desc->callback = atmel_complete_tx_dma; 997 desc->callback_param = atmel_port; 998 atmel_port->cookie_tx = dmaengine_submit(desc); 999 if (dma_submit_error(atmel_port->cookie_tx)) { 1000 dev_err(port->dev, "dma_submit_error %d\n", 1001 atmel_port->cookie_tx); 1002 return; 1003 } 1004 1005 dma_async_issue_pending(chan); 1006 } 1007 1008 if (kfifo_len(&tport->xmit_fifo) < WAKEUP_CHARS) 1009 uart_write_wakeup(port); 1010 } 1011 1012 static int atmel_prepare_tx_dma(struct uart_port *port) 1013 { 1014 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1015 struct tty_port *tport = &port->state->port; 1016 struct device *mfd_dev = port->dev->parent; 1017 dma_cap_mask_t mask; 1018 struct dma_slave_config config; 1019 struct dma_chan *chan; 1020 int ret; 1021 1022 dma_cap_zero(mask); 1023 dma_cap_set(DMA_SLAVE, mask); 1024 1025 chan = dma_request_chan(mfd_dev, "tx"); 1026 if (IS_ERR(chan)) { 1027 atmel_port->chan_tx = NULL; 1028 goto chan_err; 1029 } 1030 atmel_port->chan_tx = chan; 1031 dev_info(port->dev, "using %s for tx DMA transfers\n", 1032 dma_chan_name(atmel_port->chan_tx)); 1033 1034 spin_lock_init(&atmel_port->lock_tx); 1035 /* UART circular tx buffer is an aligned page. */ 1036 BUG_ON(!PAGE_ALIGNED(tport->xmit_buf)); 1037 atmel_port->tx_phys = dma_map_single(port->dev, tport->xmit_buf, 1038 UART_XMIT_SIZE, DMA_TO_DEVICE); 1039 1040 if (dma_mapping_error(port->dev, atmel_port->tx_phys)) { 1041 dev_dbg(port->dev, "need to release resource of dma\n"); 1042 goto chan_err; 1043 } else { 1044 dev_dbg(port->dev, "%s: mapped %lu@%p to %pad\n", __func__, 1045 UART_XMIT_SIZE, tport->xmit_buf, 1046 &atmel_port->tx_phys); 1047 } 1048 1049 /* Configure the slave DMA */ 1050 memset(&config, 0, sizeof(config)); 1051 config.direction = DMA_MEM_TO_DEV; 1052 config.dst_addr_width = (atmel_port->fifo_size) ? 1053 DMA_SLAVE_BUSWIDTH_4_BYTES : 1054 DMA_SLAVE_BUSWIDTH_1_BYTE; 1055 config.dst_addr = port->mapbase + ATMEL_US_THR; 1056 config.dst_maxburst = 1; 1057 1058 ret = dmaengine_slave_config(atmel_port->chan_tx, 1059 &config); 1060 if (ret) { 1061 dev_err(port->dev, "DMA tx slave configuration failed\n"); 1062 goto chan_err; 1063 } 1064 1065 return 0; 1066 1067 chan_err: 1068 dev_err(port->dev, "TX channel not available, switch to pio\n"); 1069 atmel_port->use_dma_tx = false; 1070 if (atmel_port->chan_tx) 1071 atmel_release_tx_dma(port); 1072 return -EINVAL; 1073 } 1074 1075 static void atmel_complete_rx_dma(void *arg) 1076 { 1077 struct uart_port *port = arg; 1078 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1079 1080 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx); 1081 } 1082 1083 static void atmel_release_rx_dma(struct uart_port *port) 1084 { 1085 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1086 struct dma_chan *chan = atmel_port->chan_rx; 1087 1088 if (chan) { 1089 dmaengine_terminate_all(chan); 1090 dma_release_channel(chan); 1091 dma_unmap_single(port->dev, atmel_port->rx_phys, 1092 ATMEL_SERIAL_RX_SIZE, DMA_FROM_DEVICE); 1093 } 1094 1095 atmel_port->desc_rx = NULL; 1096 atmel_port->chan_rx = NULL; 1097 atmel_port->cookie_rx = -EINVAL; 1098 } 1099 1100 static void atmel_rx_from_dma(struct uart_port *port) 1101 { 1102 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1103 struct tty_port *tport = &port->state->port; 1104 struct circ_buf *ring = &atmel_port->rx_ring; 1105 struct dma_chan *chan = atmel_port->chan_rx; 1106 struct dma_tx_state state; 1107 enum dma_status dmastat; 1108 size_t count; 1109 1110 1111 /* Reset the UART timeout early so that we don't miss one */ 1112 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); 1113 dmastat = dmaengine_tx_status(chan, 1114 atmel_port->cookie_rx, 1115 &state); 1116 /* Restart a new tasklet if DMA status is error */ 1117 if (dmastat == DMA_ERROR) { 1118 dev_dbg(port->dev, "Get residue error, restart tasklet\n"); 1119 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT); 1120 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx); 1121 return; 1122 } 1123 1124 /* CPU claims ownership of RX DMA buffer */ 1125 dma_sync_single_for_cpu(port->dev, atmel_port->rx_phys, 1126 ATMEL_SERIAL_RX_SIZE, DMA_FROM_DEVICE); 1127 1128 /* 1129 * ring->head points to the end of data already written by the DMA. 1130 * ring->tail points to the beginning of data to be read by the 1131 * framework. 1132 * The current transfer size should not be larger than the dma buffer 1133 * length. 1134 */ 1135 ring->head = ATMEL_SERIAL_RX_SIZE - state.residue; 1136 BUG_ON(ring->head > ATMEL_SERIAL_RX_SIZE); 1137 /* 1138 * At this point ring->head may point to the first byte right after the 1139 * last byte of the dma buffer: 1140 * 0 <= ring->head <= sg_dma_len(&atmel_port->sg_rx) 1141 * 1142 * However ring->tail must always points inside the dma buffer: 1143 * 0 <= ring->tail <= sg_dma_len(&atmel_port->sg_rx) - 1 1144 * 1145 * Since we use a ring buffer, we have to handle the case 1146 * where head is lower than tail. In such a case, we first read from 1147 * tail to the end of the buffer then reset tail. 1148 */ 1149 if (ring->head < ring->tail) { 1150 count = ATMEL_SERIAL_RX_SIZE - ring->tail; 1151 1152 tty_insert_flip_string(tport, ring->buf + ring->tail, count); 1153 ring->tail = 0; 1154 port->icount.rx += count; 1155 } 1156 1157 /* Finally we read data from tail to head */ 1158 if (ring->tail < ring->head) { 1159 count = ring->head - ring->tail; 1160 1161 tty_insert_flip_string(tport, ring->buf + ring->tail, count); 1162 /* Wrap ring->head if needed */ 1163 if (ring->head >= ATMEL_SERIAL_RX_SIZE) 1164 ring->head = 0; 1165 ring->tail = ring->head; 1166 port->icount.rx += count; 1167 } 1168 1169 /* USART retrieves ownership of RX DMA buffer */ 1170 dma_sync_single_for_device(port->dev, atmel_port->rx_phys, 1171 ATMEL_SERIAL_RX_SIZE, DMA_FROM_DEVICE); 1172 1173 tty_flip_buffer_push(tport); 1174 1175 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT); 1176 } 1177 1178 static int atmel_prepare_rx_dma(struct uart_port *port) 1179 { 1180 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1181 struct device *mfd_dev = port->dev->parent; 1182 struct dma_async_tx_descriptor *desc; 1183 dma_cap_mask_t mask; 1184 struct dma_slave_config config; 1185 struct circ_buf *ring; 1186 struct dma_chan *chan; 1187 int ret; 1188 1189 ring = &atmel_port->rx_ring; 1190 1191 dma_cap_zero(mask); 1192 dma_cap_set(DMA_CYCLIC, mask); 1193 1194 chan = dma_request_chan(mfd_dev, "rx"); 1195 if (IS_ERR(chan)) { 1196 atmel_port->chan_rx = NULL; 1197 goto chan_err; 1198 } 1199 atmel_port->chan_rx = chan; 1200 dev_info(port->dev, "using %s for rx DMA transfers\n", 1201 dma_chan_name(atmel_port->chan_rx)); 1202 1203 spin_lock_init(&atmel_port->lock_rx); 1204 /* UART circular rx buffer is an aligned page. */ 1205 BUG_ON(!PAGE_ALIGNED(ring->buf)); 1206 atmel_port->rx_phys = dma_map_single(port->dev, ring->buf, 1207 ATMEL_SERIAL_RX_SIZE, 1208 DMA_FROM_DEVICE); 1209 1210 if (dma_mapping_error(port->dev, atmel_port->rx_phys)) { 1211 dev_dbg(port->dev, "need to release resource of dma\n"); 1212 goto chan_err; 1213 } else { 1214 dev_dbg(port->dev, "%s: mapped %zu@%p to %pad\n", __func__, 1215 ATMEL_SERIAL_RX_SIZE, ring->buf, &atmel_port->rx_phys); 1216 } 1217 1218 /* Configure the slave DMA */ 1219 memset(&config, 0, sizeof(config)); 1220 config.direction = DMA_DEV_TO_MEM; 1221 config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 1222 config.src_addr = port->mapbase + ATMEL_US_RHR; 1223 config.src_maxburst = 1; 1224 1225 ret = dmaengine_slave_config(atmel_port->chan_rx, 1226 &config); 1227 if (ret) { 1228 dev_err(port->dev, "DMA rx slave configuration failed\n"); 1229 goto chan_err; 1230 } 1231 /* 1232 * Prepare a cyclic dma transfer, assign 2 descriptors, 1233 * each one is half ring buffer size 1234 */ 1235 desc = dmaengine_prep_dma_cyclic(atmel_port->chan_rx, 1236 atmel_port->rx_phys, 1237 ATMEL_SERIAL_RX_SIZE, 1238 ATMEL_SERIAL_RX_SIZE / 2, 1239 DMA_DEV_TO_MEM, 1240 DMA_PREP_INTERRUPT); 1241 if (!desc) { 1242 dev_err(port->dev, "Preparing DMA cyclic failed\n"); 1243 goto chan_err; 1244 } 1245 desc->callback = atmel_complete_rx_dma; 1246 desc->callback_param = port; 1247 atmel_port->desc_rx = desc; 1248 atmel_port->cookie_rx = dmaengine_submit(desc); 1249 if (dma_submit_error(atmel_port->cookie_rx)) { 1250 dev_err(port->dev, "dma_submit_error %d\n", 1251 atmel_port->cookie_rx); 1252 goto chan_err; 1253 } 1254 1255 dma_async_issue_pending(atmel_port->chan_rx); 1256 1257 return 0; 1258 1259 chan_err: 1260 dev_err(port->dev, "RX channel not available, switch to pio\n"); 1261 atmel_port->use_dma_rx = false; 1262 if (atmel_port->chan_rx) 1263 atmel_release_rx_dma(port); 1264 return -EINVAL; 1265 } 1266 1267 static void atmel_uart_timer_callback(struct timer_list *t) 1268 { 1269 struct atmel_uart_port *atmel_port = from_timer(atmel_port, t, 1270 uart_timer); 1271 struct uart_port *port = &atmel_port->uart; 1272 1273 if (!atomic_read(&atmel_port->tasklet_shutdown)) { 1274 tasklet_schedule(&atmel_port->tasklet_rx); 1275 mod_timer(&atmel_port->uart_timer, 1276 jiffies + uart_poll_timeout(port)); 1277 } 1278 } 1279 1280 /* 1281 * receive interrupt handler. 1282 */ 1283 static void 1284 atmel_handle_receive(struct uart_port *port, unsigned int pending) 1285 { 1286 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1287 1288 if (atmel_use_pdc_rx(port)) { 1289 /* 1290 * PDC receive. Just schedule the tasklet and let it 1291 * figure out the details. 1292 * 1293 * TODO: We're not handling error flags correctly at 1294 * the moment. 1295 */ 1296 if (pending & (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)) { 1297 atmel_uart_writel(port, ATMEL_US_IDR, 1298 (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)); 1299 atmel_tasklet_schedule(atmel_port, 1300 &atmel_port->tasklet_rx); 1301 } 1302 1303 if (pending & (ATMEL_US_RXBRK | ATMEL_US_OVRE | 1304 ATMEL_US_FRAME | ATMEL_US_PARE)) 1305 atmel_pdc_rxerr(port, pending); 1306 } 1307 1308 if (atmel_use_dma_rx(port)) { 1309 if (pending & ATMEL_US_TIMEOUT) { 1310 atmel_uart_writel(port, ATMEL_US_IDR, 1311 ATMEL_US_TIMEOUT); 1312 atmel_tasklet_schedule(atmel_port, 1313 &atmel_port->tasklet_rx); 1314 } 1315 } 1316 1317 /* Interrupt receive */ 1318 if (pending & ATMEL_US_RXRDY) 1319 atmel_rx_chars(port); 1320 else if (pending & ATMEL_US_RXBRK) { 1321 /* 1322 * End of break detected. If it came along with a 1323 * character, atmel_rx_chars will handle it. 1324 */ 1325 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); 1326 atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXBRK); 1327 atmel_port->break_active = 0; 1328 } 1329 } 1330 1331 /* 1332 * transmit interrupt handler. (Transmit is IRQF_NODELAY safe) 1333 */ 1334 static void 1335 atmel_handle_transmit(struct uart_port *port, unsigned int pending) 1336 { 1337 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1338 1339 if (pending & atmel_port->tx_done_mask) { 1340 atmel_uart_writel(port, ATMEL_US_IDR, 1341 atmel_port->tx_done_mask); 1342 1343 /* Start RX if flag was set and FIFO is empty */ 1344 if (atmel_port->hd_start_rx) { 1345 if (!(atmel_uart_readl(port, ATMEL_US_CSR) 1346 & ATMEL_US_TXEMPTY)) 1347 dev_warn(port->dev, "Should start RX, but TX fifo is not empty\n"); 1348 1349 atmel_port->hd_start_rx = false; 1350 atmel_start_rx(port); 1351 } 1352 1353 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx); 1354 } 1355 } 1356 1357 /* 1358 * status flags interrupt handler. 1359 */ 1360 static void 1361 atmel_handle_status(struct uart_port *port, unsigned int pending, 1362 unsigned int status) 1363 { 1364 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1365 unsigned int status_change; 1366 1367 if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC 1368 | ATMEL_US_CTSIC)) { 1369 status_change = status ^ atmel_port->irq_status_prev; 1370 atmel_port->irq_status_prev = status; 1371 1372 if (status_change & (ATMEL_US_RI | ATMEL_US_DSR 1373 | ATMEL_US_DCD | ATMEL_US_CTS)) { 1374 /* TODO: All reads to CSR will clear these interrupts! */ 1375 if (status_change & ATMEL_US_RI) 1376 port->icount.rng++; 1377 if (status_change & ATMEL_US_DSR) 1378 port->icount.dsr++; 1379 if (status_change & ATMEL_US_DCD) 1380 uart_handle_dcd_change(port, !(status & ATMEL_US_DCD)); 1381 if (status_change & ATMEL_US_CTS) 1382 uart_handle_cts_change(port, !(status & ATMEL_US_CTS)); 1383 1384 wake_up_interruptible(&port->state->port.delta_msr_wait); 1385 } 1386 } 1387 1388 if (pending & (ATMEL_US_NACK | ATMEL_US_ITERATION)) 1389 dev_dbg(port->dev, "ISO7816 ERROR (0x%08x)\n", pending); 1390 } 1391 1392 /* 1393 * Interrupt handler 1394 */ 1395 static irqreturn_t atmel_interrupt(int irq, void *dev_id) 1396 { 1397 struct uart_port *port = dev_id; 1398 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1399 unsigned int status, pending, mask, pass_counter = 0; 1400 1401 spin_lock(&atmel_port->lock_suspended); 1402 1403 do { 1404 status = atmel_uart_readl(port, ATMEL_US_CSR); 1405 mask = atmel_uart_readl(port, ATMEL_US_IMR); 1406 pending = status & mask; 1407 if (!pending) 1408 break; 1409 1410 if (atmel_port->suspended) { 1411 atmel_port->pending |= pending; 1412 atmel_port->pending_status = status; 1413 atmel_uart_writel(port, ATMEL_US_IDR, mask); 1414 pm_system_wakeup(); 1415 break; 1416 } 1417 1418 atmel_handle_receive(port, pending); 1419 atmel_handle_status(port, pending, status); 1420 atmel_handle_transmit(port, pending); 1421 } while (pass_counter++ < ATMEL_ISR_PASS_LIMIT); 1422 1423 spin_unlock(&atmel_port->lock_suspended); 1424 1425 return pass_counter ? IRQ_HANDLED : IRQ_NONE; 1426 } 1427 1428 static void atmel_release_tx_pdc(struct uart_port *port) 1429 { 1430 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1431 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx; 1432 1433 dma_unmap_single(port->dev, 1434 pdc->dma_addr, 1435 pdc->dma_size, 1436 DMA_TO_DEVICE); 1437 } 1438 1439 /* 1440 * Called from tasklet with ENDTX and TXBUFE interrupts disabled. 1441 */ 1442 static void atmel_tx_pdc(struct uart_port *port) 1443 { 1444 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1445 struct tty_port *tport = &port->state->port; 1446 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx; 1447 1448 /* nothing left to transmit? */ 1449 if (atmel_uart_readl(port, ATMEL_PDC_TCR)) 1450 return; 1451 uart_xmit_advance(port, pdc->ofs); 1452 pdc->ofs = 0; 1453 1454 /* more to transmit - setup next transfer */ 1455 1456 /* disable PDC transmit */ 1457 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS); 1458 1459 if (!kfifo_is_empty(&tport->xmit_fifo) && !uart_tx_stopped(port)) { 1460 unsigned int count, tail; 1461 1462 dma_sync_single_for_device(port->dev, 1463 pdc->dma_addr, 1464 pdc->dma_size, 1465 DMA_TO_DEVICE); 1466 1467 count = kfifo_out_linear(&tport->xmit_fifo, &tail, 1468 UART_XMIT_SIZE); 1469 pdc->ofs = count; 1470 1471 atmel_uart_writel(port, ATMEL_PDC_TPR, pdc->dma_addr + tail); 1472 atmel_uart_writel(port, ATMEL_PDC_TCR, count); 1473 /* re-enable PDC transmit */ 1474 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); 1475 /* Enable interrupts */ 1476 atmel_uart_writel(port, ATMEL_US_IER, 1477 atmel_port->tx_done_mask); 1478 } else { 1479 if (atmel_uart_is_half_duplex(port)) { 1480 /* DMA done, stop TX, start RX for RS485 */ 1481 atmel_start_rx(port); 1482 } 1483 } 1484 1485 if (kfifo_len(&tport->xmit_fifo) < WAKEUP_CHARS) 1486 uart_write_wakeup(port); 1487 } 1488 1489 static int atmel_prepare_tx_pdc(struct uart_port *port) 1490 { 1491 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1492 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx; 1493 struct tty_port *tport = &port->state->port; 1494 1495 pdc->buf = tport->xmit_buf; 1496 pdc->dma_addr = dma_map_single(port->dev, 1497 pdc->buf, 1498 UART_XMIT_SIZE, 1499 DMA_TO_DEVICE); 1500 pdc->dma_size = UART_XMIT_SIZE; 1501 pdc->ofs = 0; 1502 1503 return 0; 1504 } 1505 1506 static void atmel_rx_from_ring(struct uart_port *port) 1507 { 1508 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1509 struct circ_buf *ring = &atmel_port->rx_ring; 1510 unsigned int status; 1511 u8 flg; 1512 1513 while (ring->head != ring->tail) { 1514 struct atmel_uart_char c; 1515 1516 /* Make sure c is loaded after head. */ 1517 smp_rmb(); 1518 1519 c = ((struct atmel_uart_char *)ring->buf)[ring->tail]; 1520 1521 ring->tail = (ring->tail + 1) & (ATMEL_SERIAL_RINGSIZE - 1); 1522 1523 port->icount.rx++; 1524 status = c.status; 1525 flg = TTY_NORMAL; 1526 1527 /* 1528 * note that the error handling code is 1529 * out of the main execution path 1530 */ 1531 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME 1532 | ATMEL_US_OVRE | ATMEL_US_RXBRK))) { 1533 if (status & ATMEL_US_RXBRK) { 1534 /* ignore side-effect */ 1535 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME); 1536 1537 port->icount.brk++; 1538 if (uart_handle_break(port)) 1539 continue; 1540 } 1541 if (status & ATMEL_US_PARE) 1542 port->icount.parity++; 1543 if (status & ATMEL_US_FRAME) 1544 port->icount.frame++; 1545 if (status & ATMEL_US_OVRE) 1546 port->icount.overrun++; 1547 1548 status &= port->read_status_mask; 1549 1550 if (status & ATMEL_US_RXBRK) 1551 flg = TTY_BREAK; 1552 else if (status & ATMEL_US_PARE) 1553 flg = TTY_PARITY; 1554 else if (status & ATMEL_US_FRAME) 1555 flg = TTY_FRAME; 1556 } 1557 1558 1559 if (uart_handle_sysrq_char(port, c.ch)) 1560 continue; 1561 1562 uart_insert_char(port, status, ATMEL_US_OVRE, c.ch, flg); 1563 } 1564 1565 tty_flip_buffer_push(&port->state->port); 1566 } 1567 1568 static void atmel_release_rx_pdc(struct uart_port *port) 1569 { 1570 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1571 int i; 1572 1573 for (i = 0; i < 2; i++) { 1574 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i]; 1575 1576 dma_unmap_single(port->dev, 1577 pdc->dma_addr, 1578 pdc->dma_size, 1579 DMA_FROM_DEVICE); 1580 kfree(pdc->buf); 1581 } 1582 } 1583 1584 static void atmel_rx_from_pdc(struct uart_port *port) 1585 { 1586 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1587 struct tty_port *tport = &port->state->port; 1588 struct atmel_dma_buffer *pdc; 1589 int rx_idx = atmel_port->pdc_rx_idx; 1590 unsigned int head; 1591 unsigned int tail; 1592 unsigned int count; 1593 1594 do { 1595 /* Reset the UART timeout early so that we don't miss one */ 1596 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); 1597 1598 pdc = &atmel_port->pdc_rx[rx_idx]; 1599 head = atmel_uart_readl(port, ATMEL_PDC_RPR) - pdc->dma_addr; 1600 tail = pdc->ofs; 1601 1602 /* If the PDC has switched buffers, RPR won't contain 1603 * any address within the current buffer. Since head 1604 * is unsigned, we just need a one-way comparison to 1605 * find out. 1606 * 1607 * In this case, we just need to consume the entire 1608 * buffer and resubmit it for DMA. This will clear the 1609 * ENDRX bit as well, so that we can safely re-enable 1610 * all interrupts below. 1611 */ 1612 head = min(head, pdc->dma_size); 1613 1614 if (likely(head != tail)) { 1615 dma_sync_single_for_cpu(port->dev, pdc->dma_addr, 1616 pdc->dma_size, DMA_FROM_DEVICE); 1617 1618 /* 1619 * head will only wrap around when we recycle 1620 * the DMA buffer, and when that happens, we 1621 * explicitly set tail to 0. So head will 1622 * always be greater than tail. 1623 */ 1624 count = head - tail; 1625 1626 tty_insert_flip_string(tport, pdc->buf + pdc->ofs, 1627 count); 1628 1629 dma_sync_single_for_device(port->dev, pdc->dma_addr, 1630 pdc->dma_size, DMA_FROM_DEVICE); 1631 1632 port->icount.rx += count; 1633 pdc->ofs = head; 1634 } 1635 1636 /* 1637 * If the current buffer is full, we need to check if 1638 * the next one contains any additional data. 1639 */ 1640 if (head >= pdc->dma_size) { 1641 pdc->ofs = 0; 1642 atmel_uart_writel(port, ATMEL_PDC_RNPR, pdc->dma_addr); 1643 atmel_uart_writel(port, ATMEL_PDC_RNCR, pdc->dma_size); 1644 1645 rx_idx = !rx_idx; 1646 atmel_port->pdc_rx_idx = rx_idx; 1647 } 1648 } while (head >= pdc->dma_size); 1649 1650 tty_flip_buffer_push(tport); 1651 1652 atmel_uart_writel(port, ATMEL_US_IER, 1653 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT); 1654 } 1655 1656 static int atmel_prepare_rx_pdc(struct uart_port *port) 1657 { 1658 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1659 int i; 1660 1661 for (i = 0; i < 2; i++) { 1662 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i]; 1663 1664 pdc->buf = kmalloc(PDC_BUFFER_SIZE, GFP_KERNEL); 1665 if (pdc->buf == NULL) { 1666 if (i != 0) { 1667 dma_unmap_single(port->dev, 1668 atmel_port->pdc_rx[0].dma_addr, 1669 PDC_BUFFER_SIZE, 1670 DMA_FROM_DEVICE); 1671 kfree(atmel_port->pdc_rx[0].buf); 1672 } 1673 atmel_port->use_pdc_rx = false; 1674 return -ENOMEM; 1675 } 1676 pdc->dma_addr = dma_map_single(port->dev, 1677 pdc->buf, 1678 PDC_BUFFER_SIZE, 1679 DMA_FROM_DEVICE); 1680 pdc->dma_size = PDC_BUFFER_SIZE; 1681 pdc->ofs = 0; 1682 } 1683 1684 atmel_port->pdc_rx_idx = 0; 1685 1686 atmel_uart_writel(port, ATMEL_PDC_RPR, atmel_port->pdc_rx[0].dma_addr); 1687 atmel_uart_writel(port, ATMEL_PDC_RCR, PDC_BUFFER_SIZE); 1688 1689 atmel_uart_writel(port, ATMEL_PDC_RNPR, 1690 atmel_port->pdc_rx[1].dma_addr); 1691 atmel_uart_writel(port, ATMEL_PDC_RNCR, PDC_BUFFER_SIZE); 1692 1693 return 0; 1694 } 1695 1696 /* 1697 * tasklet handling tty stuff outside the interrupt handler. 1698 */ 1699 static void atmel_tasklet_rx_func(struct tasklet_struct *t) 1700 { 1701 struct atmel_uart_port *atmel_port = from_tasklet(atmel_port, t, 1702 tasklet_rx); 1703 struct uart_port *port = &atmel_port->uart; 1704 1705 /* The interrupt handler does not take the lock */ 1706 uart_port_lock(port); 1707 atmel_port->schedule_rx(port); 1708 uart_port_unlock(port); 1709 } 1710 1711 static void atmel_tasklet_tx_func(struct tasklet_struct *t) 1712 { 1713 struct atmel_uart_port *atmel_port = from_tasklet(atmel_port, t, 1714 tasklet_tx); 1715 struct uart_port *port = &atmel_port->uart; 1716 1717 /* The interrupt handler does not take the lock */ 1718 uart_port_lock(port); 1719 atmel_port->schedule_tx(port); 1720 uart_port_unlock(port); 1721 } 1722 1723 static void atmel_init_property(struct atmel_uart_port *atmel_port, 1724 struct platform_device *pdev) 1725 { 1726 struct device_node *np = pdev->dev.of_node; 1727 1728 /* DMA/PDC usage specification */ 1729 if (of_property_read_bool(np, "atmel,use-dma-rx")) { 1730 atmel_port->use_dma_rx = of_property_present(np, "dmas"); 1731 atmel_port->use_pdc_rx = !atmel_port->use_dma_rx; 1732 } else { 1733 atmel_port->use_dma_rx = false; 1734 atmel_port->use_pdc_rx = false; 1735 } 1736 1737 if (of_property_read_bool(np, "atmel,use-dma-tx")) { 1738 atmel_port->use_dma_tx = of_property_present(np, "dmas"); 1739 atmel_port->use_pdc_tx = !atmel_port->use_dma_tx; 1740 } else { 1741 atmel_port->use_dma_tx = false; 1742 atmel_port->use_pdc_tx = false; 1743 } 1744 } 1745 1746 static void atmel_set_ops(struct uart_port *port) 1747 { 1748 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1749 1750 if (atmel_use_dma_rx(port)) { 1751 atmel_port->prepare_rx = &atmel_prepare_rx_dma; 1752 atmel_port->schedule_rx = &atmel_rx_from_dma; 1753 atmel_port->release_rx = &atmel_release_rx_dma; 1754 } else if (atmel_use_pdc_rx(port)) { 1755 atmel_port->prepare_rx = &atmel_prepare_rx_pdc; 1756 atmel_port->schedule_rx = &atmel_rx_from_pdc; 1757 atmel_port->release_rx = &atmel_release_rx_pdc; 1758 } else { 1759 atmel_port->prepare_rx = NULL; 1760 atmel_port->schedule_rx = &atmel_rx_from_ring; 1761 atmel_port->release_rx = NULL; 1762 } 1763 1764 if (atmel_use_dma_tx(port)) { 1765 atmel_port->prepare_tx = &atmel_prepare_tx_dma; 1766 atmel_port->schedule_tx = &atmel_tx_dma; 1767 atmel_port->release_tx = &atmel_release_tx_dma; 1768 } else if (atmel_use_pdc_tx(port)) { 1769 atmel_port->prepare_tx = &atmel_prepare_tx_pdc; 1770 atmel_port->schedule_tx = &atmel_tx_pdc; 1771 atmel_port->release_tx = &atmel_release_tx_pdc; 1772 } else { 1773 atmel_port->prepare_tx = NULL; 1774 atmel_port->schedule_tx = &atmel_tx_chars; 1775 atmel_port->release_tx = NULL; 1776 } 1777 } 1778 1779 /* 1780 * Get ip name usart or uart 1781 */ 1782 static void atmel_get_ip_name(struct uart_port *port) 1783 { 1784 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1785 int name = atmel_uart_readl(port, ATMEL_US_NAME); 1786 u32 version; 1787 u32 usart, dbgu_uart, new_uart; 1788 /* ASCII decoding for IP version */ 1789 usart = 0x55534152; /* USAR(T) */ 1790 dbgu_uart = 0x44424755; /* DBGU */ 1791 new_uart = 0x55415254; /* UART */ 1792 1793 /* 1794 * Only USART devices from at91sam9260 SOC implement fractional 1795 * baudrate. It is available for all asynchronous modes, with the 1796 * following restriction: the sampling clock's duty cycle is not 1797 * constant. 1798 */ 1799 atmel_port->has_frac_baudrate = false; 1800 atmel_port->has_hw_timer = false; 1801 atmel_port->is_usart = false; 1802 1803 if (name == new_uart) { 1804 dev_dbg(port->dev, "Uart with hw timer"); 1805 atmel_port->has_hw_timer = true; 1806 atmel_port->rtor = ATMEL_UA_RTOR; 1807 } else if (name == usart) { 1808 dev_dbg(port->dev, "Usart\n"); 1809 atmel_port->has_frac_baudrate = true; 1810 atmel_port->has_hw_timer = true; 1811 atmel_port->is_usart = true; 1812 atmel_port->rtor = ATMEL_US_RTOR; 1813 version = atmel_uart_readl(port, ATMEL_US_VERSION); 1814 switch (version) { 1815 case 0x814: /* sama5d2 */ 1816 fallthrough; 1817 case 0x701: /* sama5d4 */ 1818 atmel_port->fidi_min = 3; 1819 atmel_port->fidi_max = 65535; 1820 break; 1821 case 0x502: /* sam9x5, sama5d3 */ 1822 atmel_port->fidi_min = 3; 1823 atmel_port->fidi_max = 2047; 1824 break; 1825 default: 1826 atmel_port->fidi_min = 1; 1827 atmel_port->fidi_max = 2047; 1828 } 1829 } else if (name == dbgu_uart) { 1830 dev_dbg(port->dev, "Dbgu or uart without hw timer\n"); 1831 } else { 1832 /* fallback for older SoCs: use version field */ 1833 version = atmel_uart_readl(port, ATMEL_US_VERSION); 1834 switch (version) { 1835 case 0x302: 1836 case 0x10213: 1837 case 0x10302: 1838 dev_dbg(port->dev, "This version is usart\n"); 1839 atmel_port->has_frac_baudrate = true; 1840 atmel_port->has_hw_timer = true; 1841 atmel_port->is_usart = true; 1842 atmel_port->rtor = ATMEL_US_RTOR; 1843 break; 1844 case 0x203: 1845 case 0x10202: 1846 dev_dbg(port->dev, "This version is uart\n"); 1847 break; 1848 default: 1849 dev_err(port->dev, "Not supported ip name nor version, set to uart\n"); 1850 } 1851 } 1852 } 1853 1854 /* 1855 * Perform initialization and enable port for reception 1856 */ 1857 static int atmel_startup(struct uart_port *port) 1858 { 1859 struct platform_device *pdev = to_platform_device(port->dev); 1860 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1861 int retval; 1862 1863 /* 1864 * Ensure that no interrupts are enabled otherwise when 1865 * request_irq() is called we could get stuck trying to 1866 * handle an unexpected interrupt 1867 */ 1868 atmel_uart_writel(port, ATMEL_US_IDR, -1); 1869 atmel_port->ms_irq_enabled = false; 1870 1871 /* 1872 * Allocate the IRQ 1873 */ 1874 retval = request_irq(port->irq, atmel_interrupt, 1875 IRQF_SHARED | IRQF_COND_SUSPEND, 1876 dev_name(&pdev->dev), port); 1877 if (retval) { 1878 dev_err(port->dev, "atmel_startup - Can't get irq\n"); 1879 return retval; 1880 } 1881 1882 atomic_set(&atmel_port->tasklet_shutdown, 0); 1883 tasklet_setup(&atmel_port->tasklet_rx, atmel_tasklet_rx_func); 1884 tasklet_setup(&atmel_port->tasklet_tx, atmel_tasklet_tx_func); 1885 1886 /* 1887 * Initialize DMA (if necessary) 1888 */ 1889 atmel_init_property(atmel_port, pdev); 1890 atmel_set_ops(port); 1891 1892 if (atmel_port->prepare_rx) { 1893 retval = atmel_port->prepare_rx(port); 1894 if (retval < 0) 1895 atmel_set_ops(port); 1896 } 1897 1898 if (atmel_port->prepare_tx) { 1899 retval = atmel_port->prepare_tx(port); 1900 if (retval < 0) 1901 atmel_set_ops(port); 1902 } 1903 1904 /* 1905 * Enable FIFO when available 1906 */ 1907 if (atmel_port->fifo_size) { 1908 unsigned int txrdym = ATMEL_US_ONE_DATA; 1909 unsigned int rxrdym = ATMEL_US_ONE_DATA; 1910 unsigned int fmr; 1911 1912 atmel_uart_writel(port, ATMEL_US_CR, 1913 ATMEL_US_FIFOEN | 1914 ATMEL_US_RXFCLR | 1915 ATMEL_US_TXFLCLR); 1916 1917 if (atmel_use_dma_tx(port)) 1918 txrdym = ATMEL_US_FOUR_DATA; 1919 1920 fmr = ATMEL_US_TXRDYM(txrdym) | ATMEL_US_RXRDYM(rxrdym); 1921 if (atmel_port->rts_high && 1922 atmel_port->rts_low) 1923 fmr |= ATMEL_US_FRTSC | 1924 ATMEL_US_RXFTHRES(atmel_port->rts_high) | 1925 ATMEL_US_RXFTHRES2(atmel_port->rts_low); 1926 1927 atmel_uart_writel(port, ATMEL_US_FMR, fmr); 1928 } 1929 1930 /* Save current CSR for comparison in atmel_tasklet_func() */ 1931 atmel_port->irq_status_prev = atmel_uart_readl(port, ATMEL_US_CSR); 1932 1933 /* 1934 * Finally, enable the serial port 1935 */ 1936 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); 1937 /* enable xmit & rcvr */ 1938 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN); 1939 atmel_port->tx_stopped = false; 1940 1941 timer_setup(&atmel_port->uart_timer, atmel_uart_timer_callback, 0); 1942 1943 if (atmel_use_pdc_rx(port)) { 1944 /* set UART timeout */ 1945 if (!atmel_port->has_hw_timer) { 1946 mod_timer(&atmel_port->uart_timer, 1947 jiffies + uart_poll_timeout(port)); 1948 /* set USART timeout */ 1949 } else { 1950 atmel_uart_writel(port, atmel_port->rtor, 1951 PDC_RX_TIMEOUT); 1952 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); 1953 1954 atmel_uart_writel(port, ATMEL_US_IER, 1955 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT); 1956 } 1957 /* enable PDC controller */ 1958 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN); 1959 } else if (atmel_use_dma_rx(port)) { 1960 /* set UART timeout */ 1961 if (!atmel_port->has_hw_timer) { 1962 mod_timer(&atmel_port->uart_timer, 1963 jiffies + uart_poll_timeout(port)); 1964 /* set USART timeout */ 1965 } else { 1966 atmel_uart_writel(port, atmel_port->rtor, 1967 PDC_RX_TIMEOUT); 1968 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO); 1969 1970 atmel_uart_writel(port, ATMEL_US_IER, 1971 ATMEL_US_TIMEOUT); 1972 } 1973 } else { 1974 /* enable receive only */ 1975 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY); 1976 } 1977 1978 return 0; 1979 } 1980 1981 /* 1982 * Flush any TX data submitted for DMA. Called when the TX circular 1983 * buffer is reset. 1984 */ 1985 static void atmel_flush_buffer(struct uart_port *port) 1986 { 1987 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 1988 1989 if (atmel_use_pdc_tx(port)) { 1990 atmel_uart_writel(port, ATMEL_PDC_TCR, 0); 1991 atmel_port->pdc_tx.ofs = 0; 1992 } 1993 /* 1994 * in uart_flush_buffer(), the xmit circular buffer has just 1995 * been cleared, so we have to reset tx_len accordingly. 1996 */ 1997 atmel_port->tx_len = 0; 1998 } 1999 2000 /* 2001 * Disable the port 2002 */ 2003 static void atmel_shutdown(struct uart_port *port) 2004 { 2005 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2006 2007 /* Disable modem control lines interrupts */ 2008 atmel_disable_ms(port); 2009 2010 /* Disable interrupts at device level */ 2011 atmel_uart_writel(port, ATMEL_US_IDR, -1); 2012 2013 /* Prevent spurious interrupts from scheduling the tasklet */ 2014 atomic_inc(&atmel_port->tasklet_shutdown); 2015 2016 /* 2017 * Prevent any tasklets being scheduled during 2018 * cleanup 2019 */ 2020 timer_delete_sync(&atmel_port->uart_timer); 2021 2022 /* Make sure that no interrupt is on the fly */ 2023 synchronize_irq(port->irq); 2024 2025 /* 2026 * Clear out any scheduled tasklets before 2027 * we destroy the buffers 2028 */ 2029 tasklet_kill(&atmel_port->tasklet_rx); 2030 tasklet_kill(&atmel_port->tasklet_tx); 2031 2032 /* 2033 * Ensure everything is stopped and 2034 * disable port and break condition. 2035 */ 2036 atmel_stop_rx(port); 2037 atmel_stop_tx(port); 2038 2039 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA); 2040 2041 /* 2042 * Shut-down the DMA. 2043 */ 2044 if (atmel_port->release_rx) 2045 atmel_port->release_rx(port); 2046 if (atmel_port->release_tx) 2047 atmel_port->release_tx(port); 2048 2049 /* 2050 * Reset ring buffer pointers 2051 */ 2052 atmel_port->rx_ring.head = 0; 2053 atmel_port->rx_ring.tail = 0; 2054 2055 /* 2056 * Free the interrupts 2057 */ 2058 free_irq(port->irq, port); 2059 2060 atmel_flush_buffer(port); 2061 } 2062 2063 /* 2064 * Power / Clock management. 2065 */ 2066 static void atmel_serial_pm(struct uart_port *port, unsigned int state, 2067 unsigned int oldstate) 2068 { 2069 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2070 2071 switch (state) { 2072 case UART_PM_STATE_ON: 2073 /* 2074 * Enable the peripheral clock for this serial port. 2075 * This is called on uart_open() or a resume event. 2076 */ 2077 clk_prepare_enable(atmel_port->clk); 2078 2079 /* re-enable interrupts if we disabled some on suspend */ 2080 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->backup_imr); 2081 break; 2082 case UART_PM_STATE_OFF: 2083 /* Back up the interrupt mask and disable all interrupts */ 2084 atmel_port->backup_imr = atmel_uart_readl(port, ATMEL_US_IMR); 2085 atmel_uart_writel(port, ATMEL_US_IDR, -1); 2086 2087 /* 2088 * Disable the peripheral clock for this serial port. 2089 * This is called on uart_close() or a suspend event. 2090 */ 2091 clk_disable_unprepare(atmel_port->clk); 2092 if (__clk_is_enabled(atmel_port->gclk)) 2093 clk_disable_unprepare(atmel_port->gclk); 2094 break; 2095 default: 2096 dev_err(port->dev, "atmel_serial: unknown pm %d\n", state); 2097 } 2098 } 2099 2100 /* 2101 * Change the port parameters 2102 */ 2103 static void atmel_set_termios(struct uart_port *port, 2104 struct ktermios *termios, 2105 const struct ktermios *old) 2106 { 2107 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2108 unsigned long flags; 2109 unsigned int old_mode, mode, imr, quot, div, cd, fp = 0; 2110 unsigned int baud, actual_baud, gclk_rate; 2111 int ret; 2112 2113 /* save the current mode register */ 2114 mode = old_mode = atmel_uart_readl(port, ATMEL_US_MR); 2115 2116 /* reset the mode, clock divisor, parity, stop bits and data size */ 2117 if (atmel_port->is_usart) 2118 mode &= ~(ATMEL_US_NBSTOP | ATMEL_US_PAR | ATMEL_US_CHRL | 2119 ATMEL_US_USCLKS | ATMEL_US_USMODE); 2120 else 2121 mode &= ~(ATMEL_UA_BRSRCCK | ATMEL_US_PAR | ATMEL_UA_FILTER); 2122 2123 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16); 2124 2125 /* byte size */ 2126 switch (termios->c_cflag & CSIZE) { 2127 case CS5: 2128 mode |= ATMEL_US_CHRL_5; 2129 break; 2130 case CS6: 2131 mode |= ATMEL_US_CHRL_6; 2132 break; 2133 case CS7: 2134 mode |= ATMEL_US_CHRL_7; 2135 break; 2136 default: 2137 mode |= ATMEL_US_CHRL_8; 2138 break; 2139 } 2140 2141 /* stop bits */ 2142 if (termios->c_cflag & CSTOPB) 2143 mode |= ATMEL_US_NBSTOP_2; 2144 2145 /* parity */ 2146 if (termios->c_cflag & PARENB) { 2147 /* Mark or Space parity */ 2148 if (termios->c_cflag & CMSPAR) { 2149 if (termios->c_cflag & PARODD) 2150 mode |= ATMEL_US_PAR_MARK; 2151 else 2152 mode |= ATMEL_US_PAR_SPACE; 2153 } else if (termios->c_cflag & PARODD) 2154 mode |= ATMEL_US_PAR_ODD; 2155 else 2156 mode |= ATMEL_US_PAR_EVEN; 2157 } else 2158 mode |= ATMEL_US_PAR_NONE; 2159 2160 uart_port_lock_irqsave(port, &flags); 2161 2162 port->read_status_mask = ATMEL_US_OVRE; 2163 if (termios->c_iflag & INPCK) 2164 port->read_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE); 2165 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) 2166 port->read_status_mask |= ATMEL_US_RXBRK; 2167 2168 if (atmel_use_pdc_rx(port)) 2169 /* need to enable error interrupts */ 2170 atmel_uart_writel(port, ATMEL_US_IER, port->read_status_mask); 2171 2172 /* 2173 * Characters to ignore 2174 */ 2175 port->ignore_status_mask = 0; 2176 if (termios->c_iflag & IGNPAR) 2177 port->ignore_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE); 2178 if (termios->c_iflag & IGNBRK) { 2179 port->ignore_status_mask |= ATMEL_US_RXBRK; 2180 /* 2181 * If we're ignoring parity and break indicators, 2182 * ignore overruns too (for real raw support). 2183 */ 2184 if (termios->c_iflag & IGNPAR) 2185 port->ignore_status_mask |= ATMEL_US_OVRE; 2186 } 2187 /* TODO: Ignore all characters if CREAD is set.*/ 2188 2189 /* update the per-port timeout */ 2190 uart_update_timeout(port, termios->c_cflag, baud); 2191 2192 /* 2193 * save/disable interrupts. The tty layer will ensure that the 2194 * transmitter is empty if requested by the caller, so there's 2195 * no need to wait for it here. 2196 */ 2197 imr = atmel_uart_readl(port, ATMEL_US_IMR); 2198 atmel_uart_writel(port, ATMEL_US_IDR, -1); 2199 2200 /* disable receiver and transmitter */ 2201 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXDIS); 2202 atmel_port->tx_stopped = true; 2203 2204 /* mode */ 2205 if (port->rs485.flags & SER_RS485_ENABLED) { 2206 atmel_uart_writel(port, ATMEL_US_TTGR, 2207 port->rs485.delay_rts_after_send); 2208 mode |= ATMEL_US_USMODE_RS485; 2209 } else if (port->iso7816.flags & SER_ISO7816_ENABLED) { 2210 atmel_uart_writel(port, ATMEL_US_TTGR, port->iso7816.tg); 2211 /* select mck clock, and output */ 2212 mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO; 2213 /* set max iterations */ 2214 mode |= ATMEL_US_MAX_ITER(3); 2215 if ((port->iso7816.flags & SER_ISO7816_T_PARAM) 2216 == SER_ISO7816_T(0)) 2217 mode |= ATMEL_US_USMODE_ISO7816_T0; 2218 else 2219 mode |= ATMEL_US_USMODE_ISO7816_T1; 2220 } else if (termios->c_cflag & CRTSCTS) { 2221 /* RS232 with hardware handshake (RTS/CTS) */ 2222 if (atmel_use_fifo(port) && 2223 !mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS)) { 2224 /* 2225 * with ATMEL_US_USMODE_HWHS set, the controller will 2226 * be able to drive the RTS pin high/low when the RX 2227 * FIFO is above RXFTHRES/below RXFTHRES2. 2228 * It will also disable the transmitter when the CTS 2229 * pin is high. 2230 * This mode is not activated if CTS pin is a GPIO 2231 * because in this case, the transmitter is always 2232 * disabled (there must be an internal pull-up 2233 * responsible for this behaviour). 2234 * If the RTS pin is a GPIO, the controller won't be 2235 * able to drive it according to the FIFO thresholds, 2236 * but it will be handled by the driver. 2237 */ 2238 mode |= ATMEL_US_USMODE_HWHS; 2239 } else { 2240 /* 2241 * For platforms without FIFO, the flow control is 2242 * handled by the driver. 2243 */ 2244 mode |= ATMEL_US_USMODE_NORMAL; 2245 } 2246 } else { 2247 /* RS232 without hadware handshake */ 2248 mode |= ATMEL_US_USMODE_NORMAL; 2249 } 2250 2251 /* 2252 * Set the baud rate: 2253 * Fractional baudrate allows to setup output frequency more 2254 * accurately. This feature is enabled only when using normal mode. 2255 * baudrate = selected clock / (8 * (2 - OVER) * (CD + FP / 8)) 2256 * Currently, OVER is always set to 0 so we get 2257 * baudrate = selected clock / (16 * (CD + FP / 8)) 2258 * then 2259 * 8 CD + FP = selected clock / (2 * baudrate) 2260 */ 2261 if (atmel_port->has_frac_baudrate) { 2262 div = DIV_ROUND_CLOSEST(port->uartclk, baud * 2); 2263 cd = div >> 3; 2264 fp = div & ATMEL_US_FP_MASK; 2265 } else { 2266 cd = uart_get_divisor(port, baud); 2267 } 2268 2269 /* 2270 * If the current value of the Clock Divisor surpasses the 16 bit 2271 * ATMEL_US_CD mask and the IP is USART, switch to the Peripheral 2272 * Clock implicitly divided by 8. 2273 * If the IP is UART however, keep the highest possible value for 2274 * the CD and avoid needless division of CD, since UART IP's do not 2275 * support implicit division of the Peripheral Clock. 2276 */ 2277 if (atmel_port->is_usart && cd > ATMEL_US_CD) { 2278 cd /= 8; 2279 mode |= ATMEL_US_USCLKS_MCK_DIV8; 2280 } else { 2281 cd = min_t(unsigned int, cd, ATMEL_US_CD); 2282 } 2283 2284 /* 2285 * If there is no Fractional Part, there is a high chance that 2286 * we may be able to generate a baudrate closer to the desired one 2287 * if we use the GCLK as the clock source driving the baudrate 2288 * generator. 2289 */ 2290 if (!atmel_port->has_frac_baudrate) { 2291 if (__clk_is_enabled(atmel_port->gclk)) 2292 clk_disable_unprepare(atmel_port->gclk); 2293 gclk_rate = clk_round_rate(atmel_port->gclk, 16 * baud); 2294 actual_baud = clk_get_rate(atmel_port->clk) / (16 * cd); 2295 if (gclk_rate && abs(atmel_error_rate(baud, actual_baud)) > 2296 abs(atmel_error_rate(baud, gclk_rate / 16))) { 2297 clk_set_rate(atmel_port->gclk, 16 * baud); 2298 ret = clk_prepare_enable(atmel_port->gclk); 2299 if (ret) 2300 goto gclk_fail; 2301 2302 if (atmel_port->is_usart) { 2303 mode &= ~ATMEL_US_USCLKS; 2304 mode |= ATMEL_US_USCLKS_GCLK; 2305 } else { 2306 mode |= ATMEL_UA_BRSRCCK; 2307 } 2308 2309 /* 2310 * Set the Clock Divisor for GCLK to 1. 2311 * Since we were able to generate the smallest 2312 * multiple of the desired baudrate times 16, 2313 * then we surely can generate a bigger multiple 2314 * with the exact error rate for an equally increased 2315 * CD. Thus no need to take into account 2316 * a higher value for CD. 2317 */ 2318 cd = 1; 2319 } 2320 } 2321 2322 gclk_fail: 2323 quot = cd | fp << ATMEL_US_FP_OFFSET; 2324 2325 if (!(port->iso7816.flags & SER_ISO7816_ENABLED)) 2326 atmel_uart_writel(port, ATMEL_US_BRGR, quot); 2327 2328 /* set the mode, clock divisor, parity, stop bits and data size */ 2329 atmel_uart_writel(port, ATMEL_US_MR, mode); 2330 2331 /* 2332 * when switching the mode, set the RTS line state according to the 2333 * new mode, otherwise keep the former state 2334 */ 2335 if ((old_mode & ATMEL_US_USMODE) != (mode & ATMEL_US_USMODE)) { 2336 unsigned int rts_state; 2337 2338 if ((mode & ATMEL_US_USMODE) == ATMEL_US_USMODE_HWHS) { 2339 /* let the hardware control the RTS line */ 2340 rts_state = ATMEL_US_RTSDIS; 2341 } else { 2342 /* force RTS line to low level */ 2343 rts_state = ATMEL_US_RTSEN; 2344 } 2345 2346 atmel_uart_writel(port, ATMEL_US_CR, rts_state); 2347 } 2348 2349 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); 2350 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN); 2351 atmel_port->tx_stopped = false; 2352 2353 /* restore interrupts */ 2354 atmel_uart_writel(port, ATMEL_US_IER, imr); 2355 2356 /* CTS flow-control and modem-status interrupts */ 2357 if (UART_ENABLE_MS(port, termios->c_cflag)) 2358 atmel_enable_ms(port); 2359 else 2360 atmel_disable_ms(port); 2361 2362 uart_port_unlock_irqrestore(port, flags); 2363 } 2364 2365 static void atmel_set_ldisc(struct uart_port *port, struct ktermios *termios) 2366 { 2367 if (termios->c_line == N_PPS) { 2368 port->flags |= UPF_HARDPPS_CD; 2369 uart_port_lock_irq(port); 2370 atmel_enable_ms(port); 2371 uart_port_unlock_irq(port); 2372 } else { 2373 port->flags &= ~UPF_HARDPPS_CD; 2374 if (!UART_ENABLE_MS(port, termios->c_cflag)) { 2375 uart_port_lock_irq(port); 2376 atmel_disable_ms(port); 2377 uart_port_unlock_irq(port); 2378 } 2379 } 2380 } 2381 2382 /* 2383 * Return string describing the specified port 2384 */ 2385 static const char *atmel_type(struct uart_port *port) 2386 { 2387 return (port->type == PORT_ATMEL) ? "ATMEL_SERIAL" : NULL; 2388 } 2389 2390 /* 2391 * Release the memory region(s) being used by 'port'. 2392 */ 2393 static void atmel_release_port(struct uart_port *port) 2394 { 2395 struct platform_device *mpdev = to_platform_device(port->dev->parent); 2396 int size = resource_size(mpdev->resource); 2397 2398 release_mem_region(port->mapbase, size); 2399 2400 if (port->flags & UPF_IOREMAP) { 2401 iounmap(port->membase); 2402 port->membase = NULL; 2403 } 2404 } 2405 2406 /* 2407 * Request the memory region(s) being used by 'port'. 2408 */ 2409 static int atmel_request_port(struct uart_port *port) 2410 { 2411 struct platform_device *mpdev = to_platform_device(port->dev->parent); 2412 2413 if (port->flags & UPF_IOREMAP) { 2414 port->membase = devm_platform_ioremap_resource(mpdev, 0); 2415 if (IS_ERR(port->membase)) 2416 return PTR_ERR(port->membase); 2417 } 2418 2419 return 0; 2420 } 2421 2422 /* 2423 * Configure/autoconfigure the port. 2424 */ 2425 static void atmel_config_port(struct uart_port *port, int flags) 2426 { 2427 if (flags & UART_CONFIG_TYPE) { 2428 port->type = PORT_ATMEL; 2429 atmel_request_port(port); 2430 } 2431 } 2432 2433 /* 2434 * Verify the new serial_struct (for TIOCSSERIAL). 2435 */ 2436 static int atmel_verify_port(struct uart_port *port, struct serial_struct *ser) 2437 { 2438 int ret = 0; 2439 if (ser->type != PORT_UNKNOWN && ser->type != PORT_ATMEL) 2440 ret = -EINVAL; 2441 if (port->irq != ser->irq) 2442 ret = -EINVAL; 2443 if (ser->io_type != SERIAL_IO_MEM) 2444 ret = -EINVAL; 2445 if (port->uartclk / 16 != ser->baud_base) 2446 ret = -EINVAL; 2447 if (port->mapbase != (unsigned long)ser->iomem_base) 2448 ret = -EINVAL; 2449 if (port->iobase != ser->port) 2450 ret = -EINVAL; 2451 if (ser->hub6 != 0) 2452 ret = -EINVAL; 2453 return ret; 2454 } 2455 2456 #ifdef CONFIG_CONSOLE_POLL 2457 static int atmel_poll_get_char(struct uart_port *port) 2458 { 2459 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_RXRDY)) 2460 cpu_relax(); 2461 2462 return atmel_uart_read_char(port); 2463 } 2464 2465 static void atmel_poll_put_char(struct uart_port *port, unsigned char ch) 2466 { 2467 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY)) 2468 cpu_relax(); 2469 2470 atmel_uart_write_char(port, ch); 2471 } 2472 #endif 2473 2474 static const struct uart_ops atmel_pops = { 2475 .tx_empty = atmel_tx_empty, 2476 .set_mctrl = atmel_set_mctrl, 2477 .get_mctrl = atmel_get_mctrl, 2478 .stop_tx = atmel_stop_tx, 2479 .start_tx = atmel_start_tx, 2480 .stop_rx = atmel_stop_rx, 2481 .enable_ms = atmel_enable_ms, 2482 .break_ctl = atmel_break_ctl, 2483 .startup = atmel_startup, 2484 .shutdown = atmel_shutdown, 2485 .flush_buffer = atmel_flush_buffer, 2486 .set_termios = atmel_set_termios, 2487 .set_ldisc = atmel_set_ldisc, 2488 .type = atmel_type, 2489 .release_port = atmel_release_port, 2490 .request_port = atmel_request_port, 2491 .config_port = atmel_config_port, 2492 .verify_port = atmel_verify_port, 2493 .pm = atmel_serial_pm, 2494 #ifdef CONFIG_CONSOLE_POLL 2495 .poll_get_char = atmel_poll_get_char, 2496 .poll_put_char = atmel_poll_put_char, 2497 #endif 2498 }; 2499 2500 static const struct serial_rs485 atmel_rs485_supported = { 2501 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RX_DURING_TX, 2502 .delay_rts_before_send = 1, 2503 .delay_rts_after_send = 1, 2504 }; 2505 2506 /* 2507 * Configure the port from the platform device resource info. 2508 */ 2509 static int atmel_init_port(struct atmel_uart_port *atmel_port, 2510 struct platform_device *pdev) 2511 { 2512 int ret; 2513 struct uart_port *port = &atmel_port->uart; 2514 struct platform_device *mpdev = to_platform_device(pdev->dev.parent); 2515 2516 atmel_init_property(atmel_port, pdev); 2517 atmel_set_ops(port); 2518 2519 port->iotype = UPIO_MEM; 2520 port->flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP; 2521 port->ops = &atmel_pops; 2522 port->fifosize = 1; 2523 port->dev = &pdev->dev; 2524 port->mapbase = mpdev->resource[0].start; 2525 port->irq = platform_get_irq(mpdev, 0); 2526 port->rs485_config = atmel_config_rs485; 2527 port->rs485_supported = atmel_rs485_supported; 2528 port->iso7816_config = atmel_config_iso7816; 2529 port->membase = NULL; 2530 2531 memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring)); 2532 2533 ret = uart_get_rs485_mode(port); 2534 if (ret) 2535 return ret; 2536 2537 port->uartclk = clk_get_rate(atmel_port->clk); 2538 2539 /* 2540 * Use TXEMPTY for interrupt when rs485 or ISO7816 else TXRDY or 2541 * ENDTX|TXBUFE 2542 */ 2543 if (atmel_uart_is_half_duplex(port)) 2544 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY; 2545 else if (atmel_use_pdc_tx(port)) { 2546 port->fifosize = PDC_BUFFER_SIZE; 2547 atmel_port->tx_done_mask = ATMEL_US_ENDTX | ATMEL_US_TXBUFE; 2548 } else { 2549 atmel_port->tx_done_mask = ATMEL_US_TXRDY; 2550 } 2551 2552 return 0; 2553 } 2554 2555 #ifdef CONFIG_SERIAL_ATMEL_CONSOLE 2556 static void atmel_console_putchar(struct uart_port *port, unsigned char ch) 2557 { 2558 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY)) 2559 cpu_relax(); 2560 atmel_uart_write_char(port, ch); 2561 } 2562 2563 /* 2564 * Interrupts are disabled on entering 2565 */ 2566 static void atmel_console_write(struct console *co, const char *s, u_int count) 2567 { 2568 struct uart_port *port = &atmel_ports[co->index].uart; 2569 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2570 unsigned int status, imr; 2571 unsigned int pdc_tx; 2572 2573 /* 2574 * First, save IMR and then disable interrupts 2575 */ 2576 imr = atmel_uart_readl(port, ATMEL_US_IMR); 2577 atmel_uart_writel(port, ATMEL_US_IDR, 2578 ATMEL_US_RXRDY | atmel_port->tx_done_mask); 2579 2580 /* Store PDC transmit status and disable it */ 2581 pdc_tx = atmel_uart_readl(port, ATMEL_PDC_PTSR) & ATMEL_PDC_TXTEN; 2582 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS); 2583 2584 /* Make sure that tx path is actually able to send characters */ 2585 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN); 2586 atmel_port->tx_stopped = false; 2587 2588 uart_console_write(port, s, count, atmel_console_putchar); 2589 2590 /* 2591 * Finally, wait for transmitter to become empty 2592 * and restore IMR 2593 */ 2594 do { 2595 status = atmel_uart_readl(port, ATMEL_US_CSR); 2596 } while (!(status & ATMEL_US_TXRDY)); 2597 2598 /* Restore PDC transmit status */ 2599 if (pdc_tx) 2600 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); 2601 2602 /* set interrupts back the way they were */ 2603 atmel_uart_writel(port, ATMEL_US_IER, imr); 2604 } 2605 2606 /* 2607 * If the port was already initialised (eg, by a boot loader), 2608 * try to determine the current setup. 2609 */ 2610 static void __init atmel_console_get_options(struct uart_port *port, int *baud, 2611 int *parity, int *bits) 2612 { 2613 unsigned int mr, quot; 2614 2615 /* 2616 * If the baud rate generator isn't running, the port wasn't 2617 * initialized by the boot loader. 2618 */ 2619 quot = atmel_uart_readl(port, ATMEL_US_BRGR) & ATMEL_US_CD; 2620 if (!quot) 2621 return; 2622 2623 mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_CHRL; 2624 if (mr == ATMEL_US_CHRL_8) 2625 *bits = 8; 2626 else 2627 *bits = 7; 2628 2629 mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_PAR; 2630 if (mr == ATMEL_US_PAR_EVEN) 2631 *parity = 'e'; 2632 else if (mr == ATMEL_US_PAR_ODD) 2633 *parity = 'o'; 2634 2635 *baud = port->uartclk / (16 * quot); 2636 } 2637 2638 static int __init atmel_console_setup(struct console *co, char *options) 2639 { 2640 struct uart_port *port = &atmel_ports[co->index].uart; 2641 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2642 int baud = 115200; 2643 int bits = 8; 2644 int parity = 'n'; 2645 int flow = 'n'; 2646 2647 if (port->membase == NULL) { 2648 /* Port not initialized yet - delay setup */ 2649 return -ENODEV; 2650 } 2651 2652 atmel_uart_writel(port, ATMEL_US_IDR, -1); 2653 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX); 2654 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN); 2655 atmel_port->tx_stopped = false; 2656 2657 if (options) 2658 uart_parse_options(options, &baud, &parity, &bits, &flow); 2659 else 2660 atmel_console_get_options(port, &baud, &parity, &bits); 2661 2662 return uart_set_options(port, co, baud, parity, bits, flow); 2663 } 2664 2665 static struct uart_driver atmel_uart; 2666 2667 static struct console atmel_console = { 2668 .name = ATMEL_DEVICENAME, 2669 .write = atmel_console_write, 2670 .device = uart_console_device, 2671 .setup = atmel_console_setup, 2672 .flags = CON_PRINTBUFFER, 2673 .index = -1, 2674 .data = &atmel_uart, 2675 }; 2676 2677 static void atmel_serial_early_write(struct console *con, const char *s, 2678 unsigned int n) 2679 { 2680 struct earlycon_device *dev = con->data; 2681 2682 uart_console_write(&dev->port, s, n, atmel_console_putchar); 2683 } 2684 2685 static int __init atmel_early_console_setup(struct earlycon_device *device, 2686 const char *options) 2687 { 2688 if (!device->port.membase) 2689 return -ENODEV; 2690 2691 device->con->write = atmel_serial_early_write; 2692 2693 return 0; 2694 } 2695 2696 OF_EARLYCON_DECLARE(atmel_serial, "atmel,at91rm9200-usart", 2697 atmel_early_console_setup); 2698 OF_EARLYCON_DECLARE(atmel_serial, "atmel,at91sam9260-usart", 2699 atmel_early_console_setup); 2700 2701 #define ATMEL_CONSOLE_DEVICE (&atmel_console) 2702 2703 #else 2704 #define ATMEL_CONSOLE_DEVICE NULL 2705 #endif 2706 2707 static struct uart_driver atmel_uart = { 2708 .owner = THIS_MODULE, 2709 .driver_name = "atmel_serial", 2710 .dev_name = ATMEL_DEVICENAME, 2711 .major = SERIAL_ATMEL_MAJOR, 2712 .minor = MINOR_START, 2713 .nr = ATMEL_MAX_UART, 2714 .cons = ATMEL_CONSOLE_DEVICE, 2715 }; 2716 2717 static bool atmel_serial_clk_will_stop(void) 2718 { 2719 #ifdef CONFIG_ARCH_AT91 2720 return at91_suspend_entering_slow_clock(); 2721 #else 2722 return false; 2723 #endif 2724 } 2725 2726 static int __maybe_unused atmel_serial_suspend(struct device *dev) 2727 { 2728 struct uart_port *port = dev_get_drvdata(dev); 2729 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2730 2731 if (uart_console(port) && console_suspend_enabled) { 2732 /* Drain the TX shifter */ 2733 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & 2734 ATMEL_US_TXEMPTY)) 2735 cpu_relax(); 2736 } 2737 2738 if (uart_console(port) && !console_suspend_enabled) { 2739 /* Cache register values as we won't get a full shutdown/startup 2740 * cycle 2741 */ 2742 atmel_port->cache.mr = atmel_uart_readl(port, ATMEL_US_MR); 2743 atmel_port->cache.imr = atmel_uart_readl(port, ATMEL_US_IMR); 2744 atmel_port->cache.brgr = atmel_uart_readl(port, ATMEL_US_BRGR); 2745 atmel_port->cache.rtor = atmel_uart_readl(port, 2746 atmel_port->rtor); 2747 atmel_port->cache.ttgr = atmel_uart_readl(port, ATMEL_US_TTGR); 2748 atmel_port->cache.fmr = atmel_uart_readl(port, ATMEL_US_FMR); 2749 atmel_port->cache.fimr = atmel_uart_readl(port, ATMEL_US_FIMR); 2750 } 2751 2752 /* we can not wake up if we're running on slow clock */ 2753 atmel_port->may_wakeup = device_may_wakeup(dev); 2754 if (atmel_serial_clk_will_stop()) { 2755 unsigned long flags; 2756 2757 spin_lock_irqsave(&atmel_port->lock_suspended, flags); 2758 atmel_port->suspended = true; 2759 spin_unlock_irqrestore(&atmel_port->lock_suspended, flags); 2760 device_set_wakeup_enable(dev, 0); 2761 } 2762 2763 uart_suspend_port(&atmel_uart, port); 2764 2765 return 0; 2766 } 2767 2768 static int __maybe_unused atmel_serial_resume(struct device *dev) 2769 { 2770 struct uart_port *port = dev_get_drvdata(dev); 2771 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2772 unsigned long flags; 2773 2774 if (uart_console(port) && !console_suspend_enabled) { 2775 atmel_uart_writel(port, ATMEL_US_MR, atmel_port->cache.mr); 2776 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->cache.imr); 2777 atmel_uart_writel(port, ATMEL_US_BRGR, atmel_port->cache.brgr); 2778 atmel_uart_writel(port, atmel_port->rtor, 2779 atmel_port->cache.rtor); 2780 atmel_uart_writel(port, ATMEL_US_TTGR, atmel_port->cache.ttgr); 2781 2782 if (atmel_port->fifo_size) { 2783 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_FIFOEN | 2784 ATMEL_US_RXFCLR | ATMEL_US_TXFLCLR); 2785 atmel_uart_writel(port, ATMEL_US_FMR, 2786 atmel_port->cache.fmr); 2787 atmel_uart_writel(port, ATMEL_US_FIER, 2788 atmel_port->cache.fimr); 2789 } 2790 atmel_start_rx(port); 2791 } 2792 2793 spin_lock_irqsave(&atmel_port->lock_suspended, flags); 2794 if (atmel_port->pending) { 2795 atmel_handle_receive(port, atmel_port->pending); 2796 atmel_handle_status(port, atmel_port->pending, 2797 atmel_port->pending_status); 2798 atmel_handle_transmit(port, atmel_port->pending); 2799 atmel_port->pending = 0; 2800 } 2801 atmel_port->suspended = false; 2802 spin_unlock_irqrestore(&atmel_port->lock_suspended, flags); 2803 2804 uart_resume_port(&atmel_uart, port); 2805 device_set_wakeup_enable(dev, atmel_port->may_wakeup); 2806 2807 return 0; 2808 } 2809 2810 static void atmel_serial_probe_fifos(struct atmel_uart_port *atmel_port, 2811 struct platform_device *pdev) 2812 { 2813 atmel_port->fifo_size = 0; 2814 atmel_port->rts_low = 0; 2815 atmel_port->rts_high = 0; 2816 2817 if (of_property_read_u32(pdev->dev.of_node, 2818 "atmel,fifo-size", 2819 &atmel_port->fifo_size)) 2820 return; 2821 2822 if (!atmel_port->fifo_size) 2823 return; 2824 2825 if (atmel_port->fifo_size < ATMEL_MIN_FIFO_SIZE) { 2826 atmel_port->fifo_size = 0; 2827 dev_err(&pdev->dev, "Invalid FIFO size\n"); 2828 return; 2829 } 2830 2831 /* 2832 * 0 <= rts_low <= rts_high <= fifo_size 2833 * Once their CTS line asserted by the remote peer, some x86 UARTs tend 2834 * to flush their internal TX FIFO, commonly up to 16 data, before 2835 * actually stopping to send new data. So we try to set the RTS High 2836 * Threshold to a reasonably high value respecting this 16 data 2837 * empirical rule when possible. 2838 */ 2839 atmel_port->rts_high = max_t(int, atmel_port->fifo_size >> 1, 2840 atmel_port->fifo_size - ATMEL_RTS_HIGH_OFFSET); 2841 atmel_port->rts_low = max_t(int, atmel_port->fifo_size >> 2, 2842 atmel_port->fifo_size - ATMEL_RTS_LOW_OFFSET); 2843 2844 dev_info(&pdev->dev, "Using FIFO (%u data)\n", 2845 atmel_port->fifo_size); 2846 dev_dbg(&pdev->dev, "RTS High Threshold : %2u data\n", 2847 atmel_port->rts_high); 2848 dev_dbg(&pdev->dev, "RTS Low Threshold : %2u data\n", 2849 atmel_port->rts_low); 2850 } 2851 2852 static int atmel_serial_probe(struct platform_device *pdev) 2853 { 2854 struct atmel_uart_port *atmel_port; 2855 struct device_node *np = pdev->dev.parent->of_node; 2856 void *data; 2857 int ret; 2858 bool rs485_enabled; 2859 2860 BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1)); 2861 2862 /* 2863 * In device tree there is no node with "atmel,at91rm9200-usart-serial" 2864 * as compatible string. This driver is probed by at91-usart mfd driver 2865 * which is just a wrapper over the atmel_serial driver and 2866 * spi-at91-usart driver. All attributes needed by this driver are 2867 * found in of_node of parent. 2868 */ 2869 pdev->dev.of_node = np; 2870 2871 ret = of_alias_get_id(np, "serial"); 2872 if (ret < 0) 2873 /* port id not found in platform data nor device-tree aliases: 2874 * auto-enumerate it */ 2875 ret = find_first_zero_bit(atmel_ports_in_use, ATMEL_MAX_UART); 2876 2877 if (ret >= ATMEL_MAX_UART) { 2878 ret = -ENODEV; 2879 goto err; 2880 } 2881 2882 if (test_and_set_bit(ret, atmel_ports_in_use)) { 2883 /* port already in use */ 2884 ret = -EBUSY; 2885 goto err; 2886 } 2887 2888 atmel_port = &atmel_ports[ret]; 2889 atmel_port->backup_imr = 0; 2890 atmel_port->uart.line = ret; 2891 atmel_port->uart.has_sysrq = IS_ENABLED(CONFIG_SERIAL_ATMEL_CONSOLE); 2892 atmel_serial_probe_fifos(atmel_port, pdev); 2893 2894 atomic_set(&atmel_port->tasklet_shutdown, 0); 2895 spin_lock_init(&atmel_port->lock_suspended); 2896 2897 atmel_port->clk = devm_clk_get(&pdev->dev, "usart"); 2898 if (IS_ERR(atmel_port->clk)) { 2899 ret = PTR_ERR(atmel_port->clk); 2900 goto err; 2901 } 2902 ret = clk_prepare_enable(atmel_port->clk); 2903 if (ret) 2904 goto err; 2905 2906 atmel_port->gclk = devm_clk_get_optional(&pdev->dev, "gclk"); 2907 if (IS_ERR(atmel_port->gclk)) { 2908 ret = PTR_ERR(atmel_port->gclk); 2909 goto err_clk_disable_unprepare; 2910 } 2911 2912 ret = atmel_init_port(atmel_port, pdev); 2913 if (ret) 2914 goto err_clk_disable_unprepare; 2915 2916 atmel_port->gpios = mctrl_gpio_init(&atmel_port->uart, 0); 2917 if (IS_ERR(atmel_port->gpios)) { 2918 ret = PTR_ERR(atmel_port->gpios); 2919 goto err_clk_disable_unprepare; 2920 } 2921 2922 if (!atmel_use_pdc_rx(&atmel_port->uart)) { 2923 ret = -ENOMEM; 2924 data = kmalloc(ATMEL_SERIAL_RX_SIZE, GFP_KERNEL); 2925 if (!data) 2926 goto err_clk_disable_unprepare; 2927 atmel_port->rx_ring.buf = data; 2928 } 2929 2930 rs485_enabled = atmel_port->uart.rs485.flags & SER_RS485_ENABLED; 2931 2932 ret = uart_add_one_port(&atmel_uart, &atmel_port->uart); 2933 if (ret) 2934 goto err_add_port; 2935 2936 device_init_wakeup(&pdev->dev, 1); 2937 platform_set_drvdata(pdev, atmel_port); 2938 2939 if (rs485_enabled) { 2940 atmel_uart_writel(&atmel_port->uart, ATMEL_US_MR, 2941 ATMEL_US_USMODE_NORMAL); 2942 atmel_uart_writel(&atmel_port->uart, ATMEL_US_CR, 2943 ATMEL_US_RTSEN); 2944 } 2945 2946 /* 2947 * Get port name of usart or uart 2948 */ 2949 atmel_get_ip_name(&atmel_port->uart); 2950 2951 /* 2952 * The peripheral clock can now safely be disabled till the port 2953 * is used 2954 */ 2955 clk_disable_unprepare(atmel_port->clk); 2956 2957 return 0; 2958 2959 err_add_port: 2960 kfree(atmel_port->rx_ring.buf); 2961 atmel_port->rx_ring.buf = NULL; 2962 err_clk_disable_unprepare: 2963 clk_disable_unprepare(atmel_port->clk); 2964 clear_bit(atmel_port->uart.line, atmel_ports_in_use); 2965 err: 2966 return ret; 2967 } 2968 2969 /* 2970 * Even if the driver is not modular, it makes sense to be able to 2971 * unbind a device: there can be many bound devices, and there are 2972 * situations where dynamic binding and unbinding can be useful. 2973 * 2974 * For example, a connected device can require a specific firmware update 2975 * protocol that needs bitbanging on IO lines, but use the regular serial 2976 * port in the normal case. 2977 */ 2978 static void atmel_serial_remove(struct platform_device *pdev) 2979 { 2980 struct uart_port *port = platform_get_drvdata(pdev); 2981 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); 2982 2983 tasklet_kill(&atmel_port->tasklet_rx); 2984 tasklet_kill(&atmel_port->tasklet_tx); 2985 2986 device_init_wakeup(&pdev->dev, 0); 2987 2988 uart_remove_one_port(&atmel_uart, port); 2989 2990 kfree(atmel_port->rx_ring.buf); 2991 2992 /* "port" is allocated statically, so we shouldn't free it */ 2993 2994 clear_bit(port->line, atmel_ports_in_use); 2995 2996 pdev->dev.of_node = NULL; 2997 } 2998 2999 static SIMPLE_DEV_PM_OPS(atmel_serial_pm_ops, atmel_serial_suspend, 3000 atmel_serial_resume); 3001 3002 static struct platform_driver atmel_serial_driver = { 3003 .probe = atmel_serial_probe, 3004 .remove = atmel_serial_remove, 3005 .driver = { 3006 .name = "atmel_usart_serial", 3007 .of_match_table = of_match_ptr(atmel_serial_dt_ids), 3008 .pm = pm_ptr(&atmel_serial_pm_ops), 3009 }, 3010 }; 3011 3012 static int __init atmel_serial_init(void) 3013 { 3014 int ret; 3015 3016 ret = uart_register_driver(&atmel_uart); 3017 if (ret) 3018 return ret; 3019 3020 ret = platform_driver_register(&atmel_serial_driver); 3021 if (ret) 3022 uart_unregister_driver(&atmel_uart); 3023 3024 return ret; 3025 } 3026 device_initcall(atmel_serial_init); 3027