1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * Driver for AMBA serial ports
4 *
5 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
6 *
7 * Copyright 1999 ARM Limited
8 * Copyright (C) 2000 Deep Blue Solutions Ltd.
9 *
10 * This is a generic driver for ARM AMBA-type serial ports. They
11 * have a lot of 16550-like features, but are not register compatible.
12 * Note that although they do have CTS, DCD and DSR inputs, they do
13 * not have an RI input, nor do they have DTR or RTS outputs. If
14 * required, these have to be supplied via some other means (eg, GPIO)
15 * and hooked into this driver.
16 */
17
18 #include <linux/module.h>
19 #include <linux/ioport.h>
20 #include <linux/init.h>
21 #include <linux/console.h>
22 #include <linux/sysrq.h>
23 #include <linux/device.h>
24 #include <linux/tty.h>
25 #include <linux/tty_flip.h>
26 #include <linux/serial_core.h>
27 #include <linux/serial.h>
28 #include <linux/amba/bus.h>
29 #include <linux/amba/serial.h>
30 #include <linux/clk.h>
31 #include <linux/slab.h>
32 #include <linux/io.h>
33
34 #define UART_NR 8
35
36 #define SERIAL_AMBA_MAJOR 204
37 #define SERIAL_AMBA_MINOR 16
38 #define SERIAL_AMBA_NR UART_NR
39
40 #define AMBA_ISR_PASS_LIMIT 256
41
42 #define UART_RX_DATA(s) (((s) & UART01x_FR_RXFE) == 0)
43 #define UART_TX_READY(s) (((s) & UART01x_FR_TXFF) == 0)
44
45 #define UART_DUMMY_RSR_RX 256
46 #define UART_PORT_SIZE 64
47
48 /*
49 * We wrap our port structure around the generic uart_port.
50 */
51 struct uart_amba_port {
52 struct uart_port port;
53 struct clk *clk;
54 struct amba_device *dev;
55 struct amba_pl010_data *data;
56 unsigned int old_status;
57 };
58
pl010_stop_tx(struct uart_port * port)59 static void pl010_stop_tx(struct uart_port *port)
60 {
61 struct uart_amba_port *uap =
62 container_of(port, struct uart_amba_port, port);
63 unsigned int cr;
64
65 cr = readb(uap->port.membase + UART010_CR);
66 cr &= ~UART010_CR_TIE;
67 writel(cr, uap->port.membase + UART010_CR);
68 }
69
pl010_start_tx(struct uart_port * port)70 static void pl010_start_tx(struct uart_port *port)
71 {
72 struct uart_amba_port *uap =
73 container_of(port, struct uart_amba_port, port);
74 unsigned int cr;
75
76 cr = readb(uap->port.membase + UART010_CR);
77 cr |= UART010_CR_TIE;
78 writel(cr, uap->port.membase + UART010_CR);
79 }
80
pl010_stop_rx(struct uart_port * port)81 static void pl010_stop_rx(struct uart_port *port)
82 {
83 struct uart_amba_port *uap =
84 container_of(port, struct uart_amba_port, port);
85 unsigned int cr;
86
87 cr = readb(uap->port.membase + UART010_CR);
88 cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
89 writel(cr, uap->port.membase + UART010_CR);
90 }
91
pl010_disable_ms(struct uart_port * port)92 static void pl010_disable_ms(struct uart_port *port)
93 {
94 struct uart_amba_port *uap = (struct uart_amba_port *)port;
95 unsigned int cr;
96
97 cr = readb(uap->port.membase + UART010_CR);
98 cr &= ~UART010_CR_MSIE;
99 writel(cr, uap->port.membase + UART010_CR);
100 }
101
pl010_enable_ms(struct uart_port * port)102 static void pl010_enable_ms(struct uart_port *port)
103 {
104 struct uart_amba_port *uap =
105 container_of(port, struct uart_amba_port, port);
106 unsigned int cr;
107
108 cr = readb(uap->port.membase + UART010_CR);
109 cr |= UART010_CR_MSIE;
110 writel(cr, uap->port.membase + UART010_CR);
111 }
112
pl010_rx_chars(struct uart_port * port)113 static void pl010_rx_chars(struct uart_port *port)
114 {
115 unsigned int status, rsr, max_count = 256;
116 u8 ch, flag;
117
118 status = readb(port->membase + UART01x_FR);
119 while (UART_RX_DATA(status) && max_count--) {
120 ch = readb(port->membase + UART01x_DR);
121 flag = TTY_NORMAL;
122
123 port->icount.rx++;
124
125 /*
126 * Note that the error handling code is
127 * out of the main execution path
128 */
129 rsr = readb(port->membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
130 if (unlikely(rsr & UART01x_RSR_ANY)) {
131 writel(0, port->membase + UART01x_ECR);
132
133 if (rsr & UART01x_RSR_BE) {
134 rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE);
135 port->icount.brk++;
136 if (uart_handle_break(port))
137 goto ignore_char;
138 } else if (rsr & UART01x_RSR_PE)
139 port->icount.parity++;
140 else if (rsr & UART01x_RSR_FE)
141 port->icount.frame++;
142 if (rsr & UART01x_RSR_OE)
143 port->icount.overrun++;
144
145 rsr &= port->read_status_mask;
146
147 if (rsr & UART01x_RSR_BE)
148 flag = TTY_BREAK;
149 else if (rsr & UART01x_RSR_PE)
150 flag = TTY_PARITY;
151 else if (rsr & UART01x_RSR_FE)
152 flag = TTY_FRAME;
153 }
154
155 if (uart_handle_sysrq_char(port, ch))
156 goto ignore_char;
157
158 uart_insert_char(port, rsr, UART01x_RSR_OE, ch, flag);
159
160 ignore_char:
161 status = readb(port->membase + UART01x_FR);
162 }
163 tty_flip_buffer_push(&port->state->port);
164 }
165
pl010_tx_chars(struct uart_port * port)166 static void pl010_tx_chars(struct uart_port *port)
167 {
168 u8 ch;
169
170 uart_port_tx_limited(port, ch, port->fifosize >> 1,
171 true,
172 writel(ch, port->membase + UART01x_DR),
173 ({}));
174 }
175
pl010_modem_status(struct uart_amba_port * uap)176 static void pl010_modem_status(struct uart_amba_port *uap)
177 {
178 struct uart_port *port = &uap->port;
179 unsigned int status, delta;
180
181 writel(0, port->membase + UART010_ICR);
182
183 status = readb(port->membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
184
185 delta = status ^ uap->old_status;
186 uap->old_status = status;
187
188 if (!delta)
189 return;
190
191 if (delta & UART01x_FR_DCD)
192 uart_handle_dcd_change(port, status & UART01x_FR_DCD);
193
194 if (delta & UART01x_FR_DSR)
195 port->icount.dsr++;
196
197 if (delta & UART01x_FR_CTS)
198 uart_handle_cts_change(port, status & UART01x_FR_CTS);
199
200 wake_up_interruptible(&port->state->port.delta_msr_wait);
201 }
202
pl010_int(int irq,void * dev_id)203 static irqreturn_t pl010_int(int irq, void *dev_id)
204 {
205 struct uart_amba_port *uap = dev_id;
206 struct uart_port *port = &uap->port;
207 unsigned int status, pass_counter = AMBA_ISR_PASS_LIMIT;
208 int handled = 0;
209
210 uart_port_lock(port);
211
212 status = readb(port->membase + UART010_IIR);
213 if (status) {
214 do {
215 if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
216 pl010_rx_chars(port);
217 if (status & UART010_IIR_MIS)
218 pl010_modem_status(uap);
219 if (status & UART010_IIR_TIS)
220 pl010_tx_chars(port);
221
222 if (pass_counter-- == 0)
223 break;
224
225 status = readb(port->membase + UART010_IIR);
226 } while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
227 UART010_IIR_TIS));
228 handled = 1;
229 }
230
231 uart_port_unlock(port);
232
233 return IRQ_RETVAL(handled);
234 }
235
pl010_tx_empty(struct uart_port * port)236 static unsigned int pl010_tx_empty(struct uart_port *port)
237 {
238 unsigned int status = readb(port->membase + UART01x_FR);
239
240 return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
241 }
242
pl010_get_mctrl(struct uart_port * port)243 static unsigned int pl010_get_mctrl(struct uart_port *port)
244 {
245 unsigned int result = 0;
246 unsigned int status;
247
248 status = readb(port->membase + UART01x_FR);
249 if (status & UART01x_FR_DCD)
250 result |= TIOCM_CAR;
251 if (status & UART01x_FR_DSR)
252 result |= TIOCM_DSR;
253 if (status & UART01x_FR_CTS)
254 result |= TIOCM_CTS;
255
256 return result;
257 }
258
pl010_set_mctrl(struct uart_port * port,unsigned int mctrl)259 static void pl010_set_mctrl(struct uart_port *port, unsigned int mctrl)
260 {
261 struct uart_amba_port *uap =
262 container_of(port, struct uart_amba_port, port);
263
264 if (uap->data)
265 uap->data->set_mctrl(uap->dev, port->membase, mctrl);
266 }
267
pl010_break_ctl(struct uart_port * port,int break_state)268 static void pl010_break_ctl(struct uart_port *port, int break_state)
269 {
270 unsigned long flags;
271 unsigned int lcr_h;
272
273 uart_port_lock_irqsave(port, &flags);
274 lcr_h = readb(port->membase + UART010_LCRH);
275 if (break_state == -1)
276 lcr_h |= UART01x_LCRH_BRK;
277 else
278 lcr_h &= ~UART01x_LCRH_BRK;
279 writel(lcr_h, port->membase + UART010_LCRH);
280 uart_port_unlock_irqrestore(port, flags);
281 }
282
pl010_startup(struct uart_port * port)283 static int pl010_startup(struct uart_port *port)
284 {
285 struct uart_amba_port *uap =
286 container_of(port, struct uart_amba_port, port);
287 int retval;
288
289 /*
290 * Try to enable the clock producer.
291 */
292 retval = clk_prepare_enable(uap->clk);
293 if (retval)
294 goto out;
295
296 port->uartclk = clk_get_rate(uap->clk);
297
298 /*
299 * Allocate the IRQ
300 */
301 retval = request_irq(port->irq, pl010_int, 0, "uart-pl010", uap);
302 if (retval)
303 goto clk_dis;
304
305 /*
306 * initialise the old status of the modem signals
307 */
308 uap->old_status = readb(port->membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
309
310 /*
311 * Finally, enable interrupts
312 */
313 writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
314 port->membase + UART010_CR);
315
316 return 0;
317
318 clk_dis:
319 clk_disable_unprepare(uap->clk);
320 out:
321 return retval;
322 }
323
pl010_shutdown(struct uart_port * port)324 static void pl010_shutdown(struct uart_port *port)
325 {
326 struct uart_amba_port *uap =
327 container_of(port, struct uart_amba_port, port);
328
329 /*
330 * Free the interrupt
331 */
332 free_irq(port->irq, uap);
333
334 /*
335 * disable all interrupts, disable the port
336 */
337 writel(0, port->membase + UART010_CR);
338
339 /* disable break condition and fifos */
340 writel(readb(port->membase + UART010_LCRH) &
341 ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN),
342 port->membase + UART010_LCRH);
343
344 /*
345 * Shut down the clock producer
346 */
347 clk_disable_unprepare(uap->clk);
348 }
349
350 static void
pl010_set_termios(struct uart_port * port,struct ktermios * termios,const struct ktermios * old)351 pl010_set_termios(struct uart_port *port, struct ktermios *termios,
352 const struct ktermios *old)
353 {
354 unsigned int lcr_h, old_cr;
355 unsigned long flags;
356 unsigned int baud, quot;
357
358 /*
359 * Ask the core to calculate the divisor for us.
360 */
361 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
362 quot = uart_get_divisor(port, baud);
363
364 switch (termios->c_cflag & CSIZE) {
365 case CS5:
366 lcr_h = UART01x_LCRH_WLEN_5;
367 break;
368 case CS6:
369 lcr_h = UART01x_LCRH_WLEN_6;
370 break;
371 case CS7:
372 lcr_h = UART01x_LCRH_WLEN_7;
373 break;
374 default: // CS8
375 lcr_h = UART01x_LCRH_WLEN_8;
376 break;
377 }
378 if (termios->c_cflag & CSTOPB)
379 lcr_h |= UART01x_LCRH_STP2;
380 if (termios->c_cflag & PARENB) {
381 lcr_h |= UART01x_LCRH_PEN;
382 if (!(termios->c_cflag & PARODD))
383 lcr_h |= UART01x_LCRH_EPS;
384 }
385 if (port->fifosize > 1)
386 lcr_h |= UART01x_LCRH_FEN;
387
388 uart_port_lock_irqsave(port, &flags);
389
390 /*
391 * Update the per-port timeout.
392 */
393 uart_update_timeout(port, termios->c_cflag, baud);
394
395 port->read_status_mask = UART01x_RSR_OE;
396 if (termios->c_iflag & INPCK)
397 port->read_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
398 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
399 port->read_status_mask |= UART01x_RSR_BE;
400
401 /*
402 * Characters to ignore
403 */
404 port->ignore_status_mask = 0;
405 if (termios->c_iflag & IGNPAR)
406 port->ignore_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
407 if (termios->c_iflag & IGNBRK) {
408 port->ignore_status_mask |= UART01x_RSR_BE;
409 /*
410 * If we're ignoring parity and break indicators,
411 * ignore overruns too (for real raw support).
412 */
413 if (termios->c_iflag & IGNPAR)
414 port->ignore_status_mask |= UART01x_RSR_OE;
415 }
416
417 /*
418 * Ignore all characters if CREAD is not set.
419 */
420 if ((termios->c_cflag & CREAD) == 0)
421 port->ignore_status_mask |= UART_DUMMY_RSR_RX;
422
423 old_cr = readb(port->membase + UART010_CR) & ~UART010_CR_MSIE;
424
425 if (UART_ENABLE_MS(port, termios->c_cflag))
426 old_cr |= UART010_CR_MSIE;
427
428 /* Set baud rate */
429 quot -= 1;
430 writel((quot & 0xf00) >> 8, port->membase + UART010_LCRM);
431 writel(quot & 0xff, port->membase + UART010_LCRL);
432
433 /*
434 * ----------v----------v----------v----------v-----
435 * NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
436 * ----------^----------^----------^----------^-----
437 */
438 writel(lcr_h, port->membase + UART010_LCRH);
439 writel(old_cr, port->membase + UART010_CR);
440
441 uart_port_unlock_irqrestore(port, flags);
442 }
443
pl010_set_ldisc(struct uart_port * port,struct ktermios * termios)444 static void pl010_set_ldisc(struct uart_port *port, struct ktermios *termios)
445 {
446 if (termios->c_line == N_PPS) {
447 port->flags |= UPF_HARDPPS_CD;
448 uart_port_lock_irq(port);
449 pl010_enable_ms(port);
450 uart_port_unlock_irq(port);
451 } else {
452 port->flags &= ~UPF_HARDPPS_CD;
453 if (!UART_ENABLE_MS(port, termios->c_cflag)) {
454 uart_port_lock_irq(port);
455 pl010_disable_ms(port);
456 uart_port_unlock_irq(port);
457 }
458 }
459 }
460
pl010_type(struct uart_port * port)461 static const char *pl010_type(struct uart_port *port)
462 {
463 return port->type == PORT_AMBA ? "AMBA" : NULL;
464 }
465
466 /*
467 * Release the memory region(s) being used by 'port'
468 */
pl010_release_port(struct uart_port * port)469 static void pl010_release_port(struct uart_port *port)
470 {
471 release_mem_region(port->mapbase, UART_PORT_SIZE);
472 }
473
474 /*
475 * Request the memory region(s) being used by 'port'
476 */
pl010_request_port(struct uart_port * port)477 static int pl010_request_port(struct uart_port *port)
478 {
479 return request_mem_region(port->mapbase, UART_PORT_SIZE, "uart-pl010")
480 != NULL ? 0 : -EBUSY;
481 }
482
483 /*
484 * Configure/autoconfigure the port.
485 */
pl010_config_port(struct uart_port * port,int flags)486 static void pl010_config_port(struct uart_port *port, int flags)
487 {
488 if (flags & UART_CONFIG_TYPE) {
489 port->type = PORT_AMBA;
490 pl010_request_port(port);
491 }
492 }
493
494 /*
495 * verify the new serial_struct (for TIOCSSERIAL).
496 */
pl010_verify_port(struct uart_port * port,struct serial_struct * ser)497 static int pl010_verify_port(struct uart_port *port, struct serial_struct *ser)
498 {
499 int ret = 0;
500 if (ser->type != PORT_UNKNOWN && ser->type != PORT_AMBA)
501 ret = -EINVAL;
502 if (ser->irq < 0 || ser->irq >= nr_irqs)
503 ret = -EINVAL;
504 if (ser->baud_base < 9600)
505 ret = -EINVAL;
506 return ret;
507 }
508
509 static const struct uart_ops amba_pl010_pops = {
510 .tx_empty = pl010_tx_empty,
511 .set_mctrl = pl010_set_mctrl,
512 .get_mctrl = pl010_get_mctrl,
513 .stop_tx = pl010_stop_tx,
514 .start_tx = pl010_start_tx,
515 .stop_rx = pl010_stop_rx,
516 .enable_ms = pl010_enable_ms,
517 .break_ctl = pl010_break_ctl,
518 .startup = pl010_startup,
519 .shutdown = pl010_shutdown,
520 .set_termios = pl010_set_termios,
521 .set_ldisc = pl010_set_ldisc,
522 .type = pl010_type,
523 .release_port = pl010_release_port,
524 .request_port = pl010_request_port,
525 .config_port = pl010_config_port,
526 .verify_port = pl010_verify_port,
527 };
528
529 static struct uart_amba_port *amba_ports[UART_NR];
530
531 #ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE
532
pl010_console_putchar(struct uart_port * port,unsigned char ch)533 static void pl010_console_putchar(struct uart_port *port, unsigned char ch)
534 {
535 unsigned int status;
536
537 do {
538 status = readb(port->membase + UART01x_FR);
539 barrier();
540 } while (!UART_TX_READY(status));
541 writel(ch, port->membase + UART01x_DR);
542 }
543
544 static void
pl010_console_write(struct console * co,const char * s,unsigned int count)545 pl010_console_write(struct console *co, const char *s, unsigned int count)
546 {
547 struct uart_amba_port *uap = amba_ports[co->index];
548 struct uart_port *port = &uap->port;
549 unsigned int status, old_cr;
550
551 clk_enable(uap->clk);
552
553 /*
554 * First save the CR then disable the interrupts
555 */
556 old_cr = readb(port->membase + UART010_CR);
557 writel(UART01x_CR_UARTEN, port->membase + UART010_CR);
558
559 uart_console_write(port, s, count, pl010_console_putchar);
560
561 /*
562 * Finally, wait for transmitter to become empty
563 * and restore the TCR
564 */
565 do {
566 status = readb(port->membase + UART01x_FR);
567 barrier();
568 } while (status & UART01x_FR_BUSY);
569 writel(old_cr, port->membase + UART010_CR);
570
571 clk_disable(uap->clk);
572 }
573
574 static void __init
pl010_console_get_options(struct uart_amba_port * uap,int * baud,int * parity,int * bits)575 pl010_console_get_options(struct uart_amba_port *uap, int *baud,
576 int *parity, int *bits)
577 {
578 if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
579 unsigned int lcr_h, quot;
580 lcr_h = readb(uap->port.membase + UART010_LCRH);
581
582 *parity = 'n';
583 if (lcr_h & UART01x_LCRH_PEN) {
584 if (lcr_h & UART01x_LCRH_EPS)
585 *parity = 'e';
586 else
587 *parity = 'o';
588 }
589
590 if ((lcr_h & 0x60) == UART01x_LCRH_WLEN_7)
591 *bits = 7;
592 else
593 *bits = 8;
594
595 quot = readb(uap->port.membase + UART010_LCRL) |
596 readb(uap->port.membase + UART010_LCRM) << 8;
597 *baud = uap->port.uartclk / (16 * (quot + 1));
598 }
599 }
600
pl010_console_setup(struct console * co,char * options)601 static int __init pl010_console_setup(struct console *co, char *options)
602 {
603 struct uart_amba_port *uap;
604 int baud = 38400;
605 int bits = 8;
606 int parity = 'n';
607 int flow = 'n';
608 int ret;
609
610 /*
611 * Check whether an invalid uart number has been specified, and
612 * if so, search for the first available port that does have
613 * console support.
614 */
615 if (co->index >= UART_NR)
616 co->index = 0;
617 uap = amba_ports[co->index];
618 if (!uap)
619 return -ENODEV;
620
621 ret = clk_prepare(uap->clk);
622 if (ret)
623 return ret;
624
625 uap->port.uartclk = clk_get_rate(uap->clk);
626
627 if (options)
628 uart_parse_options(options, &baud, &parity, &bits, &flow);
629 else
630 pl010_console_get_options(uap, &baud, &parity, &bits);
631
632 return uart_set_options(&uap->port, co, baud, parity, bits, flow);
633 }
634
635 static struct uart_driver amba_reg;
636 static struct console amba_console = {
637 .name = "ttyAM",
638 .write = pl010_console_write,
639 .device = uart_console_device,
640 .setup = pl010_console_setup,
641 .flags = CON_PRINTBUFFER,
642 .index = -1,
643 .data = &amba_reg,
644 };
645
646 #define AMBA_CONSOLE &amba_console
647 #else
648 #define AMBA_CONSOLE NULL
649 #endif
650
651 static DEFINE_MUTEX(amba_reg_lock);
652 static struct uart_driver amba_reg = {
653 .owner = THIS_MODULE,
654 .driver_name = "ttyAM",
655 .dev_name = "ttyAM",
656 .major = SERIAL_AMBA_MAJOR,
657 .minor = SERIAL_AMBA_MINOR,
658 .nr = UART_NR,
659 .cons = AMBA_CONSOLE,
660 };
661
pl010_probe(struct amba_device * dev,const struct amba_id * id)662 static int pl010_probe(struct amba_device *dev, const struct amba_id *id)
663 {
664 struct uart_amba_port *uap;
665 void __iomem *base;
666 int i, ret;
667
668 for (i = 0; i < ARRAY_SIZE(amba_ports); i++)
669 if (amba_ports[i] == NULL)
670 break;
671
672 if (i == ARRAY_SIZE(amba_ports))
673 return -EBUSY;
674
675 uap = devm_kzalloc(&dev->dev, sizeof(struct uart_amba_port),
676 GFP_KERNEL);
677 if (!uap)
678 return -ENOMEM;
679
680 base = devm_ioremap(&dev->dev, dev->res.start,
681 resource_size(&dev->res));
682 if (!base)
683 return -ENOMEM;
684
685 uap->clk = devm_clk_get(&dev->dev, NULL);
686 if (IS_ERR(uap->clk))
687 return PTR_ERR(uap->clk);
688
689 uap->port.dev = &dev->dev;
690 uap->port.mapbase = dev->res.start;
691 uap->port.membase = base;
692 uap->port.iotype = UPIO_MEM;
693 uap->port.irq = dev->irq[0];
694 uap->port.fifosize = 16;
695 uap->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_AMBA_PL010_CONSOLE);
696 uap->port.ops = &amba_pl010_pops;
697 uap->port.flags = UPF_BOOT_AUTOCONF;
698 uap->port.line = i;
699 uap->dev = dev;
700 uap->data = dev_get_platdata(&dev->dev);
701
702 amba_ports[i] = uap;
703
704 amba_set_drvdata(dev, uap);
705
706 mutex_lock(&amba_reg_lock);
707 if (!amba_reg.state) {
708 ret = uart_register_driver(&amba_reg);
709 if (ret < 0) {
710 mutex_unlock(&amba_reg_lock);
711 dev_err(uap->port.dev,
712 "Failed to register AMBA-PL010 driver\n");
713 return ret;
714 }
715 }
716 mutex_unlock(&amba_reg_lock);
717
718 ret = uart_add_one_port(&amba_reg, &uap->port);
719 if (ret)
720 amba_ports[i] = NULL;
721
722 return ret;
723 }
724
pl010_remove(struct amba_device * dev)725 static void pl010_remove(struct amba_device *dev)
726 {
727 struct uart_amba_port *uap = amba_get_drvdata(dev);
728 int i;
729 bool busy = false;
730
731 uart_remove_one_port(&amba_reg, &uap->port);
732
733 for (i = 0; i < ARRAY_SIZE(amba_ports); i++)
734 if (amba_ports[i] == uap)
735 amba_ports[i] = NULL;
736 else if (amba_ports[i])
737 busy = true;
738
739 if (!busy)
740 uart_unregister_driver(&amba_reg);
741 }
742
743 #ifdef CONFIG_PM_SLEEP
pl010_suspend(struct device * dev)744 static int pl010_suspend(struct device *dev)
745 {
746 struct uart_amba_port *uap = dev_get_drvdata(dev);
747
748 if (uap)
749 uart_suspend_port(&amba_reg, &uap->port);
750
751 return 0;
752 }
753
pl010_resume(struct device * dev)754 static int pl010_resume(struct device *dev)
755 {
756 struct uart_amba_port *uap = dev_get_drvdata(dev);
757
758 if (uap)
759 uart_resume_port(&amba_reg, &uap->port);
760
761 return 0;
762 }
763 #endif
764
765 static SIMPLE_DEV_PM_OPS(pl010_dev_pm_ops, pl010_suspend, pl010_resume);
766
767 static const struct amba_id pl010_ids[] = {
768 {
769 .id = 0x00041010,
770 .mask = 0x000fffff,
771 },
772 { 0, 0 },
773 };
774
775 MODULE_DEVICE_TABLE(amba, pl010_ids);
776
777 static struct amba_driver pl010_driver = {
778 .drv = {
779 .name = "uart-pl010",
780 .pm = &pl010_dev_pm_ops,
781 },
782 .id_table = pl010_ids,
783 .probe = pl010_probe,
784 .remove = pl010_remove,
785 };
786
pl010_init(void)787 static int __init pl010_init(void)
788 {
789 printk(KERN_INFO "Serial: AMBA driver\n");
790
791 return amba_driver_register(&pl010_driver);
792 }
793
pl010_exit(void)794 static void __exit pl010_exit(void)
795 {
796 amba_driver_unregister(&pl010_driver);
797 }
798
799 module_init(pl010_init);
800 module_exit(pl010_exit);
801
802 MODULE_AUTHOR("ARM Ltd/Deep Blue Solutions Ltd");
803 MODULE_DESCRIPTION("ARM AMBA serial port driver");
804 MODULE_LICENSE("GPL");
805