1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com> 4 */ 5 6 #include <linux/clk.h> 7 #include <linux/console.h> 8 #include <linux/io.h> 9 #include <linux/module.h> 10 #include <linux/of.h> 11 #include <linux/platform_device.h> 12 13 #include "8250.h" 14 15 /* 16 * This hardware is similar to 8250, but its register map is a bit different: 17 * - MMIO32 (regshift = 2) 18 * - FCR is not at 2, but 3 19 * - LCR and MCR are not at 3 and 4, they share 4 20 * - No SCR (Instead, CHAR can be used as a scratch register) 21 * - Divisor latch at 9, no divisor latch access bit 22 */ 23 24 #define UNIPHIER_UART_REGSHIFT 2 25 26 /* bit[15:8] = CHAR, bit[7:0] = FCR */ 27 #define UNIPHIER_UART_CHAR_FCR (3 << (UNIPHIER_UART_REGSHIFT)) 28 /* bit[15:8] = LCR, bit[7:0] = MCR */ 29 #define UNIPHIER_UART_LCR_MCR (4 << (UNIPHIER_UART_REGSHIFT)) 30 /* Divisor Latch Register */ 31 #define UNIPHIER_UART_DLR (9 << (UNIPHIER_UART_REGSHIFT)) 32 33 struct uniphier8250_priv { 34 int line; 35 struct clk *clk; 36 spinlock_t atomic_write_lock; 37 }; 38 39 #ifdef CONFIG_SERIAL_8250_CONSOLE 40 static int __init uniphier_early_console_setup(struct earlycon_device *device, 41 const char *options) 42 { 43 if (!device->port.membase) 44 return -ENODEV; 45 46 /* This hardware always expects MMIO32 register interface. */ 47 device->port.iotype = UPIO_MEM32; 48 device->port.regshift = UNIPHIER_UART_REGSHIFT; 49 50 /* 51 * Do not touch the divisor register in early_serial8250_setup(); 52 * we assume it has been initialized by a boot loader. 53 */ 54 device->baud = 0; 55 56 return early_serial8250_setup(device, options); 57 } 58 OF_EARLYCON_DECLARE(uniphier, "socionext,uniphier-uart", 59 uniphier_early_console_setup); 60 #endif 61 62 /* 63 * The register map is slightly different from that of 8250. 64 * IO callbacks must be overridden for correct access to FCR, LCR, MCR and SCR. 65 */ 66 static unsigned int uniphier_serial_in(struct uart_port *p, int offset) 67 { 68 unsigned int valshift = 0; 69 70 switch (offset) { 71 case UART_SCR: 72 /* No SCR for this hardware. Use CHAR as a scratch register */ 73 valshift = 8; 74 offset = UNIPHIER_UART_CHAR_FCR; 75 break; 76 case UART_LCR: 77 valshift = 8; 78 fallthrough; 79 case UART_MCR: 80 offset = UNIPHIER_UART_LCR_MCR; 81 break; 82 default: 83 offset <<= UNIPHIER_UART_REGSHIFT; 84 break; 85 } 86 87 /* 88 * The return value must be masked with 0xff because some registers 89 * share the same offset that must be accessed by 32-bit write/read. 90 * 8 or 16 bit access to this hardware result in unexpected behavior. 91 */ 92 return (readl(p->membase + offset) >> valshift) & 0xff; 93 } 94 95 static void uniphier_serial_out(struct uart_port *p, int offset, int value) 96 { 97 unsigned int valshift = 0; 98 bool normal = false; 99 100 switch (offset) { 101 case UART_SCR: 102 /* No SCR for this hardware. Use CHAR as a scratch register */ 103 valshift = 8; 104 fallthrough; 105 case UART_FCR: 106 offset = UNIPHIER_UART_CHAR_FCR; 107 break; 108 case UART_LCR: 109 valshift = 8; 110 /* Divisor latch access bit does not exist. */ 111 value &= ~UART_LCR_DLAB; 112 fallthrough; 113 case UART_MCR: 114 offset = UNIPHIER_UART_LCR_MCR; 115 break; 116 default: 117 offset <<= UNIPHIER_UART_REGSHIFT; 118 normal = true; 119 break; 120 } 121 122 if (normal) { 123 writel(value, p->membase + offset); 124 } else { 125 /* 126 * Special case: two registers share the same address that 127 * must be 32-bit accessed. As this is not longer atomic safe, 128 * take a lock just in case. 129 */ 130 struct uniphier8250_priv *priv = p->private_data; 131 unsigned long flags; 132 u32 tmp; 133 134 spin_lock_irqsave(&priv->atomic_write_lock, flags); 135 tmp = readl(p->membase + offset); 136 tmp &= ~(0xff << valshift); 137 tmp |= value << valshift; 138 writel(tmp, p->membase + offset); 139 spin_unlock_irqrestore(&priv->atomic_write_lock, flags); 140 } 141 } 142 143 /* 144 * This hardware does not have the divisor latch access bit. 145 * The divisor latch register exists at different address. 146 * Override dl_read/write callbacks. 147 */ 148 static u32 uniphier_serial_dl_read(struct uart_8250_port *up) 149 { 150 return readl(up->port.membase + UNIPHIER_UART_DLR); 151 } 152 153 static void uniphier_serial_dl_write(struct uart_8250_port *up, u32 value) 154 { 155 writel(value, up->port.membase + UNIPHIER_UART_DLR); 156 } 157 158 static int uniphier_uart_probe(struct platform_device *pdev) 159 { 160 struct device *dev = &pdev->dev; 161 struct uart_8250_port up; 162 struct uniphier8250_priv *priv; 163 struct resource *regs; 164 void __iomem *membase; 165 int irq; 166 int ret; 167 168 regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); 169 if (!regs) { 170 dev_err(dev, "failed to get memory resource\n"); 171 return -EINVAL; 172 } 173 174 membase = devm_ioremap(dev, regs->start, resource_size(regs)); 175 if (!membase) 176 return -ENOMEM; 177 178 irq = platform_get_irq(pdev, 0); 179 if (irq < 0) 180 return irq; 181 182 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); 183 if (!priv) 184 return -ENOMEM; 185 186 memset(&up, 0, sizeof(up)); 187 188 ret = of_alias_get_id(dev->of_node, "serial"); 189 if (ret < 0) { 190 dev_err(dev, "failed to get alias id\n"); 191 return ret; 192 } 193 up.port.line = ret; 194 195 priv->clk = devm_clk_get(dev, NULL); 196 if (IS_ERR(priv->clk)) { 197 dev_err(dev, "failed to get clock\n"); 198 return PTR_ERR(priv->clk); 199 } 200 201 ret = clk_prepare_enable(priv->clk); 202 if (ret) 203 return ret; 204 205 up.port.uartclk = clk_get_rate(priv->clk); 206 207 spin_lock_init(&priv->atomic_write_lock); 208 209 up.port.dev = dev; 210 up.port.private_data = priv; 211 up.port.mapbase = regs->start; 212 up.port.mapsize = resource_size(regs); 213 up.port.membase = membase; 214 up.port.irq = irq; 215 216 up.port.type = PORT_16550A; 217 up.port.iotype = UPIO_MEM32; 218 up.port.fifosize = 64; 219 up.port.regshift = UNIPHIER_UART_REGSHIFT; 220 up.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE; 221 up.capabilities = UART_CAP_FIFO; 222 223 if (of_property_read_bool(dev->of_node, "auto-flow-control")) 224 up.capabilities |= UART_CAP_AFE; 225 226 up.port.serial_in = uniphier_serial_in; 227 up.port.serial_out = uniphier_serial_out; 228 up.dl_read = uniphier_serial_dl_read; 229 up.dl_write = uniphier_serial_dl_write; 230 231 ret = serial8250_register_8250_port(&up); 232 if (ret < 0) { 233 dev_err(dev, "failed to register 8250 port\n"); 234 clk_disable_unprepare(priv->clk); 235 return ret; 236 } 237 priv->line = ret; 238 239 platform_set_drvdata(pdev, priv); 240 241 return 0; 242 } 243 244 static void uniphier_uart_remove(struct platform_device *pdev) 245 { 246 struct uniphier8250_priv *priv = platform_get_drvdata(pdev); 247 248 serial8250_unregister_port(priv->line); 249 clk_disable_unprepare(priv->clk); 250 } 251 252 static int __maybe_unused uniphier_uart_suspend(struct device *dev) 253 { 254 struct uniphier8250_priv *priv = dev_get_drvdata(dev); 255 struct uart_8250_port *up = serial8250_get_port(priv->line); 256 257 serial8250_suspend_port(priv->line); 258 259 if (!uart_console(&up->port) || console_suspend_enabled) 260 clk_disable_unprepare(priv->clk); 261 262 return 0; 263 } 264 265 static int __maybe_unused uniphier_uart_resume(struct device *dev) 266 { 267 struct uniphier8250_priv *priv = dev_get_drvdata(dev); 268 struct uart_8250_port *up = serial8250_get_port(priv->line); 269 int ret; 270 271 if (!uart_console(&up->port) || console_suspend_enabled) { 272 ret = clk_prepare_enable(priv->clk); 273 if (ret) 274 return ret; 275 } 276 277 serial8250_resume_port(priv->line); 278 279 return 0; 280 } 281 282 static const struct dev_pm_ops uniphier_uart_pm_ops = { 283 SET_SYSTEM_SLEEP_PM_OPS(uniphier_uart_suspend, uniphier_uart_resume) 284 }; 285 286 static const struct of_device_id uniphier_uart_match[] = { 287 { .compatible = "socionext,uniphier-uart" }, 288 { /* sentinel */ } 289 }; 290 MODULE_DEVICE_TABLE(of, uniphier_uart_match); 291 292 static struct platform_driver uniphier_uart_platform_driver = { 293 .probe = uniphier_uart_probe, 294 .remove_new = uniphier_uart_remove, 295 .driver = { 296 .name = "uniphier-uart", 297 .of_match_table = uniphier_uart_match, 298 .pm = &uniphier_uart_pm_ops, 299 }, 300 }; 301 module_platform_driver(uniphier_uart_platform_driver); 302 303 MODULE_AUTHOR("Masahiro Yamada <yamada.masahiro@socionext.com>"); 304 MODULE_DESCRIPTION("UniPhier UART driver"); 305 MODULE_LICENSE("GPL"); 306