1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Mediatek 8250 driver. 4 * 5 * Copyright (c) 2014 MundoReader S.L. 6 * Author: Matthias Brugger <matthias.bgg@gmail.com> 7 */ 8 #include <linux/clk.h> 9 #include <linux/io.h> 10 #include <linux/module.h> 11 #include <linux/of_irq.h> 12 #include <linux/of_platform.h> 13 #include <linux/pinctrl/consumer.h> 14 #include <linux/platform_device.h> 15 #include <linux/pm_runtime.h> 16 #include <linux/serial_8250.h> 17 #include <linux/serial_reg.h> 18 #include <linux/console.h> 19 #include <linux/dma-mapping.h> 20 #include <linux/tty.h> 21 #include <linux/tty_flip.h> 22 23 #include "8250.h" 24 25 #define MTK_UART_HIGHS 0x09 /* Highspeed register */ 26 #define MTK_UART_SAMPLE_COUNT 0x0a /* Sample count register */ 27 #define MTK_UART_SAMPLE_POINT 0x0b /* Sample point register */ 28 #define MTK_UART_RATE_FIX 0x0d /* UART Rate Fix Register */ 29 #define MTK_UART_ESCAPE_DAT 0x10 /* Escape Character register */ 30 #define MTK_UART_ESCAPE_EN 0x11 /* Escape Enable register */ 31 #define MTK_UART_DMA_EN 0x13 /* DMA Enable register */ 32 #define MTK_UART_RXTRI_AD 0x14 /* RX Trigger address */ 33 #define MTK_UART_FRACDIV_L 0x15 /* Fractional divider LSB address */ 34 #define MTK_UART_FRACDIV_M 0x16 /* Fractional divider MSB address */ 35 #define MTK_UART_DEBUG0 0x18 36 #define MTK_UART_IER_XOFFI 0x20 /* Enable XOFF character interrupt */ 37 #define MTK_UART_IER_RTSI 0x40 /* Enable RTS Modem status interrupt */ 38 #define MTK_UART_IER_CTSI 0x80 /* Enable CTS Modem status interrupt */ 39 40 #define MTK_UART_EFR 38 /* I/O: Extended Features Register */ 41 #define MTK_UART_EFR_EN 0x10 /* Enable enhancement feature */ 42 #define MTK_UART_EFR_RTS 0x40 /* Enable hardware rx flow control */ 43 #define MTK_UART_EFR_CTS 0x80 /* Enable hardware tx flow control */ 44 #define MTK_UART_EFR_NO_SW_FC 0x0 /* no sw flow control */ 45 #define MTK_UART_EFR_XON1_XOFF1 0xa /* XON1/XOFF1 as sw flow control */ 46 #define MTK_UART_EFR_XON2_XOFF2 0x5 /* XON2/XOFF2 as sw flow control */ 47 #define MTK_UART_EFR_SW_FC_MASK 0xf /* Enable CTS Modem status interrupt */ 48 #define MTK_UART_EFR_HW_FC (MTK_UART_EFR_RTS | MTK_UART_EFR_CTS) 49 #define MTK_UART_DMA_EN_TX 0x2 50 #define MTK_UART_DMA_EN_RX 0x5 51 52 #define MTK_UART_ESCAPE_CHAR 0x77 /* Escape char added under sw fc */ 53 #define MTK_UART_RX_SIZE 0x8000 54 #define MTK_UART_TX_TRIGGER 1 55 #define MTK_UART_RX_TRIGGER MTK_UART_RX_SIZE 56 57 #define MTK_UART_XON1 40 /* I/O: Xon character 1 */ 58 #define MTK_UART_XOFF1 42 /* I/O: Xoff character 1 */ 59 60 #ifdef CONFIG_SERIAL_8250_DMA 61 enum dma_rx_status { 62 DMA_RX_START = 0, 63 DMA_RX_RUNNING = 1, 64 DMA_RX_SHUTDOWN = 2, 65 }; 66 #endif 67 68 struct mtk8250_data { 69 int line; 70 unsigned int rx_pos; 71 unsigned int clk_count; 72 struct clk *uart_clk; 73 struct clk *bus_clk; 74 struct uart_8250_dma *dma; 75 #ifdef CONFIG_SERIAL_8250_DMA 76 enum dma_rx_status rx_status; 77 #endif 78 int rx_wakeup_irq; 79 }; 80 81 /* flow control mode */ 82 enum { 83 MTK_UART_FC_NONE, 84 MTK_UART_FC_SW, 85 MTK_UART_FC_HW, 86 }; 87 88 #ifdef CONFIG_SERIAL_8250_DMA 89 static void mtk8250_rx_dma(struct uart_8250_port *up); 90 91 static void mtk8250_dma_rx_complete(void *param) 92 { 93 struct uart_8250_port *up = param; 94 struct uart_8250_dma *dma = up->dma; 95 struct mtk8250_data *data = up->port.private_data; 96 struct tty_port *tty_port = &up->port.state->port; 97 struct dma_tx_state state; 98 int copied, total, cnt; 99 unsigned char *ptr; 100 unsigned long flags; 101 102 if (data->rx_status == DMA_RX_SHUTDOWN) 103 return; 104 105 uart_port_lock_irqsave(&up->port, &flags); 106 107 dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state); 108 total = dma->rx_size - state.residue; 109 cnt = total; 110 111 if ((data->rx_pos + cnt) > dma->rx_size) 112 cnt = dma->rx_size - data->rx_pos; 113 114 ptr = (unsigned char *)(data->rx_pos + dma->rx_buf); 115 copied = tty_insert_flip_string(tty_port, ptr, cnt); 116 data->rx_pos += cnt; 117 118 if (total > cnt) { 119 ptr = (unsigned char *)(dma->rx_buf); 120 cnt = total - cnt; 121 copied += tty_insert_flip_string(tty_port, ptr, cnt); 122 data->rx_pos = cnt; 123 } 124 125 up->port.icount.rx += copied; 126 127 tty_flip_buffer_push(tty_port); 128 129 mtk8250_rx_dma(up); 130 131 uart_port_unlock_irqrestore(&up->port, flags); 132 } 133 134 static void mtk8250_rx_dma(struct uart_8250_port *up) 135 { 136 struct uart_8250_dma *dma = up->dma; 137 struct dma_async_tx_descriptor *desc; 138 139 desc = dmaengine_prep_slave_single(dma->rxchan, dma->rx_addr, 140 dma->rx_size, DMA_DEV_TO_MEM, 141 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 142 if (!desc) { 143 pr_err("failed to prepare rx slave single\n"); 144 return; 145 } 146 147 desc->callback = mtk8250_dma_rx_complete; 148 desc->callback_param = up; 149 150 dma->rx_cookie = dmaengine_submit(desc); 151 152 dma_async_issue_pending(dma->rxchan); 153 } 154 155 static void mtk8250_dma_enable(struct uart_8250_port *up) 156 { 157 struct uart_8250_dma *dma = up->dma; 158 struct mtk8250_data *data = up->port.private_data; 159 int lcr = serial_in(up, UART_LCR); 160 161 if (data->rx_status != DMA_RX_START) 162 return; 163 164 dma->rxconf.src_port_window_size = dma->rx_size; 165 dma->rxconf.src_addr = dma->rx_addr; 166 167 dma->txconf.dst_port_window_size = UART_XMIT_SIZE; 168 dma->txconf.dst_addr = dma->tx_addr; 169 170 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | 171 UART_FCR_CLEAR_XMIT); 172 serial_out(up, MTK_UART_DMA_EN, 173 MTK_UART_DMA_EN_RX | MTK_UART_DMA_EN_TX); 174 175 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 176 serial_out(up, MTK_UART_EFR, UART_EFR_ECB); 177 serial_out(up, UART_LCR, lcr); 178 179 if (dmaengine_slave_config(dma->rxchan, &dma->rxconf) != 0) 180 pr_err("failed to configure rx dma channel\n"); 181 if (dmaengine_slave_config(dma->txchan, &dma->txconf) != 0) 182 pr_err("failed to configure tx dma channel\n"); 183 184 data->rx_status = DMA_RX_RUNNING; 185 data->rx_pos = 0; 186 mtk8250_rx_dma(up); 187 } 188 #endif 189 190 static int mtk8250_startup(struct uart_port *port) 191 { 192 #ifdef CONFIG_SERIAL_8250_DMA 193 struct uart_8250_port *up = up_to_u8250p(port); 194 struct mtk8250_data *data = port->private_data; 195 196 /* disable DMA for console */ 197 if (uart_console(port)) 198 up->dma = NULL; 199 200 if (up->dma) { 201 data->rx_status = DMA_RX_START; 202 kfifo_reset(&port->state->port.xmit_fifo); 203 } 204 #endif 205 memset(&port->icount, 0, sizeof(port->icount)); 206 207 return serial8250_do_startup(port); 208 } 209 210 static void mtk8250_shutdown(struct uart_port *port) 211 { 212 struct uart_8250_port *up = up_to_u8250p(port); 213 struct mtk8250_data *data = port->private_data; 214 int irq = data->rx_wakeup_irq; 215 216 #ifdef CONFIG_SERIAL_8250_DMA 217 if (up->dma) 218 data->rx_status = DMA_RX_SHUTDOWN; 219 #endif 220 221 serial8250_do_shutdown(port); 222 223 if (irq >= 0) 224 serial8250_do_set_mctrl(&up->port, TIOCM_RTS); 225 } 226 227 static void mtk8250_disable_intrs(struct uart_8250_port *up, int mask) 228 { 229 /* Port locked to synchronize UART_IER access against the console. */ 230 lockdep_assert_held_once(&up->port.lock); 231 232 serial_out(up, UART_IER, serial_in(up, UART_IER) & (~mask)); 233 } 234 235 static void mtk8250_enable_intrs(struct uart_8250_port *up, int mask) 236 { 237 /* Port locked to synchronize UART_IER access against the console. */ 238 lockdep_assert_held_once(&up->port.lock); 239 240 serial_out(up, UART_IER, serial_in(up, UART_IER) | mask); 241 } 242 243 static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode) 244 { 245 struct uart_port *port = &up->port; 246 int lcr = serial_in(up, UART_LCR); 247 248 /* Port locked to synchronize UART_IER access against the console. */ 249 lockdep_assert_held_once(&port->lock); 250 251 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 252 serial_out(up, MTK_UART_EFR, UART_EFR_ECB); 253 serial_out(up, UART_LCR, lcr); 254 lcr = serial_in(up, UART_LCR); 255 256 switch (mode) { 257 case MTK_UART_FC_NONE: 258 serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); 259 serial_out(up, MTK_UART_ESCAPE_EN, 0x00); 260 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 261 serial_out(up, MTK_UART_EFR, serial_in(up, MTK_UART_EFR) & 262 (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))); 263 serial_out(up, UART_LCR, lcr); 264 mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI | 265 MTK_UART_IER_RTSI | MTK_UART_IER_CTSI); 266 break; 267 268 case MTK_UART_FC_HW: 269 serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); 270 serial_out(up, MTK_UART_ESCAPE_EN, 0x00); 271 serial_out(up, UART_MCR, UART_MCR_RTS); 272 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 273 274 /*enable hw flow control*/ 275 serial_out(up, MTK_UART_EFR, MTK_UART_EFR_HW_FC | 276 (serial_in(up, MTK_UART_EFR) & 277 (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)))); 278 279 serial_out(up, UART_LCR, lcr); 280 mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI); 281 mtk8250_enable_intrs(up, MTK_UART_IER_CTSI | MTK_UART_IER_RTSI); 282 break; 283 284 case MTK_UART_FC_SW: /*MTK software flow control */ 285 serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); 286 serial_out(up, MTK_UART_ESCAPE_EN, 0x01); 287 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); 288 289 /*enable sw flow control */ 290 serial_out(up, MTK_UART_EFR, MTK_UART_EFR_XON1_XOFF1 | 291 (serial_in(up, MTK_UART_EFR) & 292 (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)))); 293 294 serial_out(up, MTK_UART_XON1, START_CHAR(port->state->port.tty)); 295 serial_out(up, MTK_UART_XOFF1, STOP_CHAR(port->state->port.tty)); 296 serial_out(up, UART_LCR, lcr); 297 mtk8250_disable_intrs(up, MTK_UART_IER_CTSI|MTK_UART_IER_RTSI); 298 mtk8250_enable_intrs(up, MTK_UART_IER_XOFFI); 299 break; 300 default: 301 break; 302 } 303 } 304 305 static void 306 mtk8250_set_termios(struct uart_port *port, struct ktermios *termios, 307 const struct ktermios *old) 308 { 309 static const unsigned short fraction_L_mapping[] = { 310 0, 1, 0x5, 0x15, 0x55, 0x57, 0x57, 0x77, 0x7F, 0xFF, 0xFF 311 }; 312 static const unsigned short fraction_M_mapping[] = { 313 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 3 314 }; 315 struct uart_8250_port *up = up_to_u8250p(port); 316 unsigned int baud, quot, fraction; 317 unsigned long flags; 318 int mode; 319 320 #ifdef CONFIG_SERIAL_8250_DMA 321 if (up->dma) { 322 if (uart_console(port)) { 323 devm_kfree(up->port.dev, up->dma); 324 up->dma = NULL; 325 } else { 326 mtk8250_dma_enable(up); 327 } 328 } 329 #endif 330 331 /* 332 * Store the requested baud rate before calling the generic 8250 333 * set_termios method. Standard 8250 port expects bauds to be 334 * no higher than (uartclk / 16) so the baud will be clamped if it 335 * gets out of that bound. Mediatek 8250 port supports speed 336 * higher than that, therefore we'll get original baud rate back 337 * after calling the generic set_termios method and recalculate 338 * the speed later in this method. 339 */ 340 baud = tty_termios_baud_rate(termios); 341 342 serial8250_do_set_termios(port, termios, NULL); 343 344 tty_termios_encode_baud_rate(termios, baud, baud); 345 346 /* 347 * Mediatek UARTs use an extra highspeed register (MTK_UART_HIGHS) 348 * 349 * We need to recalcualte the quot register, as the claculation depends 350 * on the vaule in the highspeed register. 351 * 352 * Some baudrates are not supported by the chip, so we use the next 353 * lower rate supported and update termios c_flag. 354 * 355 * If highspeed register is set to 3, we need to specify sample count 356 * and sample point to increase accuracy. If not, we reset the 357 * registers to their default values. 358 */ 359 baud = uart_get_baud_rate(port, termios, old, 360 port->uartclk / 16 / UART_DIV_MAX, 361 port->uartclk); 362 363 if (baud < 115200) { 364 serial_port_out(port, MTK_UART_HIGHS, 0x0); 365 quot = uart_get_divisor(port, baud); 366 } else { 367 serial_port_out(port, MTK_UART_HIGHS, 0x3); 368 quot = DIV_ROUND_UP(port->uartclk, 256 * baud); 369 } 370 371 /* 372 * Ok, we're now changing the port state. Do it with 373 * interrupts disabled. 374 */ 375 uart_port_lock_irqsave(port, &flags); 376 377 /* 378 * Update the per-port timeout. 379 */ 380 uart_update_timeout(port, termios->c_cflag, baud); 381 382 /* set DLAB we have cval saved in up->lcr from the call to the core */ 383 serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB); 384 serial_dl_write(up, quot); 385 386 /* reset DLAB */ 387 serial_port_out(port, UART_LCR, up->lcr); 388 389 if (baud >= 115200) { 390 unsigned int tmp; 391 392 tmp = (port->uartclk / (baud * quot)) - 1; 393 serial_port_out(port, MTK_UART_SAMPLE_COUNT, tmp); 394 serial_port_out(port, MTK_UART_SAMPLE_POINT, 395 (tmp >> 1) - 1); 396 397 /*count fraction to set fractoin register */ 398 fraction = ((port->uartclk * 100) / baud / quot) % 100; 399 fraction = DIV_ROUND_CLOSEST(fraction, 10); 400 serial_port_out(port, MTK_UART_FRACDIV_L, 401 fraction_L_mapping[fraction]); 402 serial_port_out(port, MTK_UART_FRACDIV_M, 403 fraction_M_mapping[fraction]); 404 } else { 405 serial_port_out(port, MTK_UART_SAMPLE_COUNT, 0x00); 406 serial_port_out(port, MTK_UART_SAMPLE_POINT, 0xff); 407 serial_port_out(port, MTK_UART_FRACDIV_L, 0x00); 408 serial_port_out(port, MTK_UART_FRACDIV_M, 0x00); 409 } 410 411 if ((termios->c_cflag & CRTSCTS) && (!(termios->c_iflag & CRTSCTS))) 412 mode = MTK_UART_FC_HW; 413 else if (termios->c_iflag & CRTSCTS) 414 mode = MTK_UART_FC_SW; 415 else 416 mode = MTK_UART_FC_NONE; 417 418 mtk8250_set_flow_ctrl(up, mode); 419 420 if (uart_console(port)) 421 up->port.cons->cflag = termios->c_cflag; 422 423 uart_port_unlock_irqrestore(port, flags); 424 /* Don't rewrite B0 */ 425 if (tty_termios_baud_rate(termios)) 426 tty_termios_encode_baud_rate(termios, baud, baud); 427 } 428 429 static int __maybe_unused mtk8250_runtime_suspend(struct device *dev) 430 { 431 struct mtk8250_data *data = dev_get_drvdata(dev); 432 struct uart_8250_port *up = serial8250_get_port(data->line); 433 434 /* wait until UART in idle status */ 435 while 436 (serial_in(up, MTK_UART_DEBUG0)); 437 438 clk_disable_unprepare(data->bus_clk); 439 440 return 0; 441 } 442 443 static int __maybe_unused mtk8250_runtime_resume(struct device *dev) 444 { 445 struct mtk8250_data *data = dev_get_drvdata(dev); 446 447 clk_prepare_enable(data->bus_clk); 448 449 return 0; 450 } 451 452 static void 453 mtk8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old) 454 { 455 if (!state) 456 pm_runtime_get_sync(port->dev); 457 458 serial8250_do_pm(port, state, old); 459 460 if (state) 461 pm_runtime_put_sync_suspend(port->dev); 462 } 463 464 #ifdef CONFIG_SERIAL_8250_DMA 465 static bool mtk8250_dma_filter(struct dma_chan *chan, void *param) 466 { 467 return false; 468 } 469 #endif 470 471 static int mtk8250_probe_of(struct platform_device *pdev, struct uart_port *p, 472 struct mtk8250_data *data) 473 { 474 #ifdef CONFIG_SERIAL_8250_DMA 475 int dmacnt; 476 #endif 477 478 data->uart_clk = devm_clk_get(&pdev->dev, "baud"); 479 if (IS_ERR(data->uart_clk)) { 480 /* 481 * For compatibility with older device trees try unnamed 482 * clk when no baud clk can be found. 483 */ 484 data->uart_clk = devm_clk_get(&pdev->dev, NULL); 485 if (IS_ERR(data->uart_clk)) { 486 dev_warn(&pdev->dev, "Can't get uart clock\n"); 487 return PTR_ERR(data->uart_clk); 488 } 489 490 return 0; 491 } 492 493 data->bus_clk = devm_clk_get_enabled(&pdev->dev, "bus"); 494 if (IS_ERR(data->bus_clk)) 495 return PTR_ERR(data->bus_clk); 496 497 data->dma = NULL; 498 #ifdef CONFIG_SERIAL_8250_DMA 499 dmacnt = of_property_count_strings(pdev->dev.of_node, "dma-names"); 500 if (dmacnt == 2) { 501 data->dma = devm_kzalloc(&pdev->dev, sizeof(*data->dma), 502 GFP_KERNEL); 503 if (!data->dma) 504 return -ENOMEM; 505 506 data->dma->fn = mtk8250_dma_filter; 507 data->dma->rx_size = MTK_UART_RX_SIZE; 508 data->dma->rxconf.src_maxburst = MTK_UART_RX_TRIGGER; 509 data->dma->txconf.dst_maxburst = MTK_UART_TX_TRIGGER; 510 } 511 #endif 512 513 return 0; 514 } 515 516 static int mtk8250_probe(struct platform_device *pdev) 517 { 518 struct uart_8250_port uart = {}; 519 struct mtk8250_data *data; 520 struct resource *regs; 521 int irq, err; 522 523 irq = platform_get_irq(pdev, 0); 524 if (irq < 0) 525 return irq; 526 527 regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); 528 if (!regs) { 529 dev_err(&pdev->dev, "no registers defined\n"); 530 return -EINVAL; 531 } 532 533 uart.port.membase = devm_ioremap(&pdev->dev, regs->start, 534 resource_size(regs)); 535 if (!uart.port.membase) 536 return -ENOMEM; 537 538 data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); 539 if (!data) 540 return -ENOMEM; 541 542 data->clk_count = 0; 543 544 if (pdev->dev.of_node) { 545 err = mtk8250_probe_of(pdev, &uart.port, data); 546 if (err) 547 return err; 548 } else 549 return -ENODEV; 550 551 spin_lock_init(&uart.port.lock); 552 uart.port.mapbase = regs->start; 553 uart.port.irq = irq; 554 uart.port.pm = mtk8250_do_pm; 555 uart.port.type = PORT_16550; 556 uart.port.flags = UPF_BOOT_AUTOCONF | UPF_FIXED_PORT; 557 uart.port.dev = &pdev->dev; 558 uart.port.iotype = UPIO_MEM32; 559 uart.port.regshift = 2; 560 uart.port.private_data = data; 561 uart.port.shutdown = mtk8250_shutdown; 562 uart.port.startup = mtk8250_startup; 563 uart.port.set_termios = mtk8250_set_termios; 564 uart.port.uartclk = clk_get_rate(data->uart_clk); 565 #ifdef CONFIG_SERIAL_8250_DMA 566 if (data->dma) 567 uart.dma = data->dma; 568 #endif 569 570 /* Disable Rate Fix function */ 571 writel(0x0, uart.port.membase + 572 (MTK_UART_RATE_FIX << uart.port.regshift)); 573 574 platform_set_drvdata(pdev, data); 575 576 data->line = serial8250_register_8250_port(&uart); 577 if (data->line < 0) 578 return data->line; 579 580 data->rx_wakeup_irq = platform_get_irq_optional(pdev, 1); 581 582 pm_runtime_set_active(&pdev->dev); 583 pm_runtime_enable(&pdev->dev); 584 585 return 0; 586 } 587 588 static void mtk8250_remove(struct platform_device *pdev) 589 { 590 struct mtk8250_data *data = platform_get_drvdata(pdev); 591 592 pm_runtime_get_sync(&pdev->dev); 593 594 serial8250_unregister_port(data->line); 595 596 pm_runtime_disable(&pdev->dev); 597 pm_runtime_put_noidle(&pdev->dev); 598 } 599 600 static int __maybe_unused mtk8250_suspend(struct device *dev) 601 { 602 struct mtk8250_data *data = dev_get_drvdata(dev); 603 int irq = data->rx_wakeup_irq; 604 int err; 605 606 serial8250_suspend_port(data->line); 607 608 pinctrl_pm_select_sleep_state(dev); 609 if (irq >= 0) { 610 err = enable_irq_wake(irq); 611 if (err) { 612 dev_err(dev, 613 "failed to enable irq wake on IRQ %d: %d\n", 614 irq, err); 615 pinctrl_pm_select_default_state(dev); 616 serial8250_resume_port(data->line); 617 return err; 618 } 619 } 620 621 return 0; 622 } 623 624 static int __maybe_unused mtk8250_resume(struct device *dev) 625 { 626 struct mtk8250_data *data = dev_get_drvdata(dev); 627 int irq = data->rx_wakeup_irq; 628 629 if (irq >= 0) 630 disable_irq_wake(irq); 631 pinctrl_pm_select_default_state(dev); 632 633 serial8250_resume_port(data->line); 634 635 return 0; 636 } 637 638 static const struct dev_pm_ops mtk8250_pm_ops = { 639 SET_SYSTEM_SLEEP_PM_OPS(mtk8250_suspend, mtk8250_resume) 640 SET_RUNTIME_PM_OPS(mtk8250_runtime_suspend, mtk8250_runtime_resume, 641 NULL) 642 }; 643 644 static const struct of_device_id mtk8250_of_match[] = { 645 { .compatible = "mediatek,mt6577-uart" }, 646 { /* Sentinel */ } 647 }; 648 MODULE_DEVICE_TABLE(of, mtk8250_of_match); 649 650 static struct platform_driver mtk8250_platform_driver = { 651 .driver = { 652 .name = "mt6577-uart", 653 .pm = &mtk8250_pm_ops, 654 .of_match_table = mtk8250_of_match, 655 }, 656 .probe = mtk8250_probe, 657 .remove_new = mtk8250_remove, 658 }; 659 module_platform_driver(mtk8250_platform_driver); 660 661 #ifdef CONFIG_SERIAL_8250_CONSOLE 662 static int __init early_mtk8250_setup(struct earlycon_device *device, 663 const char *options) 664 { 665 if (!device->port.membase) 666 return -ENODEV; 667 668 device->port.iotype = UPIO_MEM32; 669 device->port.regshift = 2; 670 671 return early_serial8250_setup(device, NULL); 672 } 673 674 OF_EARLYCON_DECLARE(mtk8250, "mediatek,mt6577-uart", early_mtk8250_setup); 675 #endif 676 677 MODULE_AUTHOR("Matthias Brugger"); 678 MODULE_LICENSE("GPL"); 679 MODULE_DESCRIPTION("Mediatek 8250 serial port driver"); 680