1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Serial port driver for NXP LPC18xx/43xx UART 4 * 5 * Copyright (C) 2015 Joachim Eastwood <manabian@gmail.com> 6 * 7 * Based on 8250_mtk.c: 8 * Copyright (c) 2014 MundoReader S.L. 9 * Matthias Brugger <matthias.bgg@gmail.com> 10 */ 11 12 #include <linux/clk.h> 13 #include <linux/io.h> 14 #include <linux/module.h> 15 #include <linux/of.h> 16 #include <linux/platform_device.h> 17 18 #include "8250.h" 19 20 /* Additional LPC18xx/43xx 8250 registers and bits */ 21 #define LPC18XX_UART_RS485CTRL (0x04c / sizeof(u32)) 22 #define LPC18XX_UART_RS485CTRL_NMMEN BIT(0) 23 #define LPC18XX_UART_RS485CTRL_DCTRL BIT(4) 24 #define LPC18XX_UART_RS485CTRL_OINV BIT(5) 25 #define LPC18XX_UART_RS485DLY (0x054 / sizeof(u32)) 26 #define LPC18XX_UART_RS485DLY_MAX 255 27 28 struct lpc18xx_uart_data { 29 struct uart_8250_dma dma; 30 struct clk *clk_uart; 31 struct clk *clk_reg; 32 int line; 33 }; 34 35 static int lpc18xx_rs485_config(struct uart_port *port, struct ktermios *termios, 36 struct serial_rs485 *rs485) 37 { 38 struct uart_8250_port *up = up_to_u8250p(port); 39 u32 rs485_ctrl_reg = 0; 40 u32 rs485_dly_reg = 0; 41 unsigned baud_clk; 42 43 if (rs485->flags & SER_RS485_ENABLED) { 44 rs485_ctrl_reg |= LPC18XX_UART_RS485CTRL_NMMEN | 45 LPC18XX_UART_RS485CTRL_DCTRL; 46 47 if (rs485->flags & SER_RS485_RTS_ON_SEND) 48 rs485_ctrl_reg |= LPC18XX_UART_RS485CTRL_OINV; 49 } 50 51 if (rs485->delay_rts_after_send) { 52 baud_clk = port->uartclk / up->dl_read(up); 53 rs485_dly_reg = DIV_ROUND_UP(rs485->delay_rts_after_send 54 * baud_clk, MSEC_PER_SEC); 55 56 if (rs485_dly_reg > LPC18XX_UART_RS485DLY_MAX) 57 rs485_dly_reg = LPC18XX_UART_RS485DLY_MAX; 58 59 /* Calculate the resulting delay in ms */ 60 rs485->delay_rts_after_send = (rs485_dly_reg * MSEC_PER_SEC) 61 / baud_clk; 62 } 63 64 serial_out(up, LPC18XX_UART_RS485CTRL, rs485_ctrl_reg); 65 serial_out(up, LPC18XX_UART_RS485DLY, rs485_dly_reg); 66 67 return 0; 68 } 69 70 static void lpc18xx_uart_serial_out(struct uart_port *p, int offset, int value) 71 { 72 /* 73 * For DMA mode one must ensure that the UART_FCR_DMA_SELECT 74 * bit is set when FIFO is enabled. Even if DMA is not used 75 * setting this bit doesn't seem to affect anything. 76 */ 77 if (offset == UART_FCR && (value & UART_FCR_ENABLE_FIFO)) 78 value |= UART_FCR_DMA_SELECT; 79 80 offset = offset << p->regshift; 81 writel(value, p->membase + offset); 82 } 83 84 static const struct serial_rs485 lpc18xx_rs485_supported = { 85 .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND, 86 .delay_rts_after_send = 1, 87 /* Delay RTS before send is not supported */ 88 }; 89 90 static int lpc18xx_serial_probe(struct platform_device *pdev) 91 { 92 struct lpc18xx_uart_data *data; 93 struct uart_8250_port uart; 94 struct resource *res; 95 int ret; 96 97 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 98 if (!res) { 99 dev_err(&pdev->dev, "memory resource not found"); 100 return -EINVAL; 101 } 102 103 memset(&uart, 0, sizeof(uart)); 104 105 uart.port.membase = devm_ioremap(&pdev->dev, res->start, 106 resource_size(res)); 107 if (!uart.port.membase) 108 return -ENOMEM; 109 110 data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); 111 if (!data) 112 return -ENOMEM; 113 114 data->clk_uart = devm_clk_get(&pdev->dev, "uartclk"); 115 if (IS_ERR(data->clk_uart)) { 116 dev_err(&pdev->dev, "uart clock not found\n"); 117 return PTR_ERR(data->clk_uart); 118 } 119 120 data->clk_reg = devm_clk_get(&pdev->dev, "reg"); 121 if (IS_ERR(data->clk_reg)) { 122 dev_err(&pdev->dev, "reg clock not found\n"); 123 return PTR_ERR(data->clk_reg); 124 } 125 126 ret = clk_prepare_enable(data->clk_reg); 127 if (ret) { 128 dev_err(&pdev->dev, "unable to enable reg clock\n"); 129 return ret; 130 } 131 132 ret = clk_prepare_enable(data->clk_uart); 133 if (ret) { 134 dev_err(&pdev->dev, "unable to enable uart clock\n"); 135 goto dis_clk_reg; 136 } 137 138 data->dma.rx_param = data; 139 data->dma.tx_param = data; 140 141 spin_lock_init(&uart.port.lock); 142 uart.port.dev = &pdev->dev; 143 uart.port.mapbase = res->start; 144 uart.port.type = PORT_16550A; 145 uart.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE | UPF_SKIP_TEST; 146 uart.port.uartclk = clk_get_rate(data->clk_uart); 147 uart.port.private_data = data; 148 uart.port.rs485_config = lpc18xx_rs485_config; 149 uart.port.rs485_supported = lpc18xx_rs485_supported; 150 uart.port.serial_out = lpc18xx_uart_serial_out; 151 152 ret = uart_read_port_properties(&uart.port); 153 if (ret) 154 goto dis_uart_clk; 155 156 uart.port.iotype = UPIO_MEM32; 157 uart.port.regshift = 2; 158 159 uart.dma = &data->dma; 160 uart.dma->rxconf.src_maxburst = 1; 161 uart.dma->txconf.dst_maxburst = 1; 162 163 ret = serial8250_register_8250_port(&uart); 164 if (ret < 0) { 165 dev_err(&pdev->dev, "unable to register 8250 port\n"); 166 goto dis_uart_clk; 167 } 168 169 data->line = ret; 170 platform_set_drvdata(pdev, data); 171 172 return 0; 173 174 dis_uart_clk: 175 clk_disable_unprepare(data->clk_uart); 176 dis_clk_reg: 177 clk_disable_unprepare(data->clk_reg); 178 return ret; 179 } 180 181 static void lpc18xx_serial_remove(struct platform_device *pdev) 182 { 183 struct lpc18xx_uart_data *data = platform_get_drvdata(pdev); 184 185 serial8250_unregister_port(data->line); 186 clk_disable_unprepare(data->clk_uart); 187 clk_disable_unprepare(data->clk_reg); 188 } 189 190 static const struct of_device_id lpc18xx_serial_match[] = { 191 { .compatible = "nxp,lpc1850-uart" }, 192 { }, 193 }; 194 MODULE_DEVICE_TABLE(of, lpc18xx_serial_match); 195 196 static struct platform_driver lpc18xx_serial_driver = { 197 .probe = lpc18xx_serial_probe, 198 .remove = lpc18xx_serial_remove, 199 .driver = { 200 .name = "lpc18xx-uart", 201 .of_match_table = lpc18xx_serial_match, 202 }, 203 }; 204 module_platform_driver(lpc18xx_serial_driver); 205 206 MODULE_AUTHOR("Joachim Eastwood <manabian@gmail.com>"); 207 MODULE_DESCRIPTION("Serial port driver NXP LPC18xx/43xx devices"); 208 MODULE_LICENSE("GPL v2"); 209