1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Probe module for 8250/16550-type Exar chips PCI serial ports. 4 * 5 * Based on drivers/tty/serial/8250/8250_pci.c, 6 * 7 * Copyright (C) 2017 Sudip Mukherjee, All Rights Reserved. 8 */ 9 #include <linux/acpi.h> 10 #include <linux/dmi.h> 11 #include <linux/io.h> 12 #include <linux/kernel.h> 13 #include <linux/module.h> 14 #include <linux/pci.h> 15 #include <linux/property.h> 16 #include <linux/serial_core.h> 17 #include <linux/serial_reg.h> 18 #include <linux/slab.h> 19 #include <linux/string.h> 20 #include <linux/tty.h> 21 #include <linux/8250_pci.h> 22 #include <linux/delay.h> 23 24 #include <asm/byteorder.h> 25 26 #include "8250.h" 27 28 #define PCI_DEVICE_ID_ACCESSIO_COM_2S 0x1052 29 #define PCI_DEVICE_ID_ACCESSIO_COM_4S 0x105d 30 #define PCI_DEVICE_ID_ACCESSIO_COM_8S 0x106c 31 #define PCI_DEVICE_ID_ACCESSIO_COM232_8 0x10a8 32 #define PCI_DEVICE_ID_ACCESSIO_COM_2SM 0x10d2 33 #define PCI_DEVICE_ID_ACCESSIO_COM_4SM 0x10db 34 #define PCI_DEVICE_ID_ACCESSIO_COM_8SM 0x10ea 35 36 #define PCI_DEVICE_ID_COMMTECH_4224PCI335 0x0002 37 #define PCI_DEVICE_ID_COMMTECH_4222PCI335 0x0004 38 #define PCI_DEVICE_ID_COMMTECH_2324PCI335 0x000a 39 #define PCI_DEVICE_ID_COMMTECH_2328PCI335 0x000b 40 #define PCI_DEVICE_ID_COMMTECH_4224PCIE 0x0020 41 #define PCI_DEVICE_ID_COMMTECH_4228PCIE 0x0021 42 #define PCI_DEVICE_ID_COMMTECH_4222PCIE 0x0022 43 #define PCI_DEVICE_ID_EXAR_XR17V4358 0x4358 44 #define PCI_DEVICE_ID_EXAR_XR17V8358 0x8358 45 46 #define UART_EXAR_INT0 0x80 47 #define UART_EXAR_8XMODE 0x88 /* 8X sampling rate select */ 48 #define UART_EXAR_SLEEP 0x8b /* Sleep mode */ 49 #define UART_EXAR_DVID 0x8d /* Device identification */ 50 51 #define UART_EXAR_FCTR 0x08 /* Feature Control Register */ 52 #define UART_FCTR_EXAR_IRDA 0x10 /* IrDa data encode select */ 53 #define UART_FCTR_EXAR_485 0x20 /* Auto 485 half duplex dir ctl */ 54 #define UART_FCTR_EXAR_TRGA 0x00 /* FIFO trigger table A */ 55 #define UART_FCTR_EXAR_TRGB 0x60 /* FIFO trigger table B */ 56 #define UART_FCTR_EXAR_TRGC 0x80 /* FIFO trigger table C */ 57 #define UART_FCTR_EXAR_TRGD 0xc0 /* FIFO trigger table D programmable */ 58 59 #define UART_EXAR_TXTRG 0x0a /* Tx FIFO trigger level write-only */ 60 #define UART_EXAR_RXTRG 0x0b /* Rx FIFO trigger level write-only */ 61 62 #define UART_EXAR_MPIOINT_7_0 0x8f /* MPIOINT[7:0] */ 63 #define UART_EXAR_MPIOLVL_7_0 0x90 /* MPIOLVL[7:0] */ 64 #define UART_EXAR_MPIO3T_7_0 0x91 /* MPIO3T[7:0] */ 65 #define UART_EXAR_MPIOINV_7_0 0x92 /* MPIOINV[7:0] */ 66 #define UART_EXAR_MPIOSEL_7_0 0x93 /* MPIOSEL[7:0] */ 67 #define UART_EXAR_MPIOOD_7_0 0x94 /* MPIOOD[7:0] */ 68 #define UART_EXAR_MPIOINT_15_8 0x95 /* MPIOINT[15:8] */ 69 #define UART_EXAR_MPIOLVL_15_8 0x96 /* MPIOLVL[15:8] */ 70 #define UART_EXAR_MPIO3T_15_8 0x97 /* MPIO3T[15:8] */ 71 #define UART_EXAR_MPIOINV_15_8 0x98 /* MPIOINV[15:8] */ 72 #define UART_EXAR_MPIOSEL_15_8 0x99 /* MPIOSEL[15:8] */ 73 #define UART_EXAR_MPIOOD_15_8 0x9a /* MPIOOD[15:8] */ 74 75 #define UART_EXAR_RS485_DLY(x) ((x) << 4) 76 77 /* 78 * IOT2040 MPIO wiring semantics: 79 * 80 * MPIO Port Function 81 * ---- ---- -------- 82 * 0 2 Mode bit 0 83 * 1 2 Mode bit 1 84 * 2 2 Terminate bus 85 * 3 - <reserved> 86 * 4 3 Mode bit 0 87 * 5 3 Mode bit 1 88 * 6 3 Terminate bus 89 * 7 - <reserved> 90 * 8 2 Enable 91 * 9 3 Enable 92 * 10 - Red LED 93 * 11..15 - <unused> 94 */ 95 96 /* IOT2040 MPIOs 0..7 */ 97 #define IOT2040_UART_MODE_RS232 0x01 98 #define IOT2040_UART_MODE_RS485 0x02 99 #define IOT2040_UART_MODE_RS422 0x03 100 #define IOT2040_UART_TERMINATE_BUS 0x04 101 102 #define IOT2040_UART1_MASK 0x0f 103 #define IOT2040_UART2_SHIFT 4 104 105 #define IOT2040_UARTS_DEFAULT_MODE 0x11 /* both RS232 */ 106 #define IOT2040_UARTS_GPIO_LO_MODE 0x88 /* reserved pins as input */ 107 108 /* IOT2040 MPIOs 8..15 */ 109 #define IOT2040_UARTS_ENABLE 0x03 110 #define IOT2040_UARTS_GPIO_HI_MODE 0xF8 /* enable & LED as outputs */ 111 112 struct exar8250; 113 114 struct exar8250_platform { 115 int (*rs485_config)(struct uart_port *, struct serial_rs485 *); 116 int (*register_gpio)(struct pci_dev *, struct uart_8250_port *); 117 }; 118 119 /** 120 * struct exar8250_board - board information 121 * @num_ports: number of serial ports 122 * @reg_shift: describes UART register mapping in PCI memory 123 * @setup: quirk run at ->probe() stage 124 * @exit: quirk run at ->remove() stage 125 */ 126 struct exar8250_board { 127 unsigned int num_ports; 128 unsigned int reg_shift; 129 int (*setup)(struct exar8250 *, struct pci_dev *, 130 struct uart_8250_port *, int); 131 void (*exit)(struct pci_dev *pcidev); 132 }; 133 134 struct exar8250 { 135 unsigned int nr; 136 struct exar8250_board *board; 137 void __iomem *virt; 138 int line[]; 139 }; 140 141 static void exar_pm(struct uart_port *port, unsigned int state, unsigned int old) 142 { 143 /* 144 * Exar UARTs have a SLEEP register that enables or disables each UART 145 * to enter sleep mode separately. On the XR17V35x the register 146 * is accessible to each UART at the UART_EXAR_SLEEP offset, but 147 * the UART channel may only write to the corresponding bit. 148 */ 149 serial_port_out(port, UART_EXAR_SLEEP, state ? 0xff : 0); 150 } 151 152 /* 153 * XR17V35x UARTs have an extra fractional divisor register (DLD) 154 * Calculate divisor with extra 4-bit fractional portion 155 */ 156 static unsigned int xr17v35x_get_divisor(struct uart_port *p, unsigned int baud, 157 unsigned int *frac) 158 { 159 unsigned int quot_16; 160 161 quot_16 = DIV_ROUND_CLOSEST(p->uartclk, baud); 162 *frac = quot_16 & 0x0f; 163 164 return quot_16 >> 4; 165 } 166 167 static void xr17v35x_set_divisor(struct uart_port *p, unsigned int baud, 168 unsigned int quot, unsigned int quot_frac) 169 { 170 serial8250_do_set_divisor(p, baud, quot, quot_frac); 171 172 /* Preserve bits not related to baudrate; DLD[7:4]. */ 173 quot_frac |= serial_port_in(p, 0x2) & 0xf0; 174 serial_port_out(p, 0x2, quot_frac); 175 } 176 177 static int xr17v35x_startup(struct uart_port *port) 178 { 179 /* 180 * First enable access to IER [7:5], ISR [5:4], FCR [5:4], 181 * MCR [7:5] and MSR [7:0] 182 */ 183 serial_port_out(port, UART_XR_EFR, UART_EFR_ECB); 184 185 /* 186 * Make sure all interrups are masked until initialization is 187 * complete and the FIFOs are cleared 188 */ 189 serial_port_out(port, UART_IER, 0); 190 191 return serial8250_do_startup(port); 192 } 193 194 static void exar_shutdown(struct uart_port *port) 195 { 196 unsigned char lsr; 197 bool tx_complete = false; 198 struct uart_8250_port *up = up_to_u8250p(port); 199 struct circ_buf *xmit = &port->state->xmit; 200 int i = 0; 201 202 do { 203 lsr = serial_in(up, UART_LSR); 204 if (lsr & (UART_LSR_TEMT | UART_LSR_THRE)) 205 tx_complete = true; 206 else 207 tx_complete = false; 208 usleep_range(1000, 1100); 209 } while (!uart_circ_empty(xmit) && !tx_complete && i++ < 1000); 210 211 serial8250_do_shutdown(port); 212 } 213 214 static int default_setup(struct exar8250 *priv, struct pci_dev *pcidev, 215 int idx, unsigned int offset, 216 struct uart_8250_port *port) 217 { 218 const struct exar8250_board *board = priv->board; 219 unsigned int bar = 0; 220 unsigned char status; 221 222 port->port.iotype = UPIO_MEM; 223 port->port.mapbase = pci_resource_start(pcidev, bar) + offset; 224 port->port.membase = priv->virt + offset; 225 port->port.regshift = board->reg_shift; 226 227 /* 228 * XR17V35x UARTs have an extra divisor register, DLD that gets enabled 229 * with when DLAB is set which will cause the device to incorrectly match 230 * and assign port type to PORT_16650. The EFR for this UART is found 231 * at offset 0x09. Instead check the Deice ID (DVID) register 232 * for a 2, 4 or 8 port UART. 233 */ 234 status = readb(port->port.membase + UART_EXAR_DVID); 235 if (status == 0x82 || status == 0x84 || status == 0x88) { 236 port->port.type = PORT_XR17V35X; 237 238 port->port.get_divisor = xr17v35x_get_divisor; 239 port->port.set_divisor = xr17v35x_set_divisor; 240 241 port->port.startup = xr17v35x_startup; 242 } else { 243 port->port.type = PORT_XR17D15X; 244 } 245 246 port->port.pm = exar_pm; 247 port->port.shutdown = exar_shutdown; 248 249 return 0; 250 } 251 252 static int 253 pci_fastcom335_setup(struct exar8250 *priv, struct pci_dev *pcidev, 254 struct uart_8250_port *port, int idx) 255 { 256 unsigned int offset = idx * 0x200; 257 unsigned int baud = 1843200; 258 u8 __iomem *p; 259 int err; 260 261 port->port.uartclk = baud * 16; 262 263 err = default_setup(priv, pcidev, idx, offset, port); 264 if (err) 265 return err; 266 267 p = port->port.membase; 268 269 writeb(0x00, p + UART_EXAR_8XMODE); 270 writeb(UART_FCTR_EXAR_TRGD, p + UART_EXAR_FCTR); 271 writeb(32, p + UART_EXAR_TXTRG); 272 writeb(32, p + UART_EXAR_RXTRG); 273 274 /* 275 * Setup Multipurpose Input/Output pins. 276 */ 277 if (idx == 0) { 278 switch (pcidev->device) { 279 case PCI_DEVICE_ID_COMMTECH_4222PCI335: 280 case PCI_DEVICE_ID_COMMTECH_4224PCI335: 281 writeb(0x78, p + UART_EXAR_MPIOLVL_7_0); 282 writeb(0x00, p + UART_EXAR_MPIOINV_7_0); 283 writeb(0x00, p + UART_EXAR_MPIOSEL_7_0); 284 break; 285 case PCI_DEVICE_ID_COMMTECH_2324PCI335: 286 case PCI_DEVICE_ID_COMMTECH_2328PCI335: 287 writeb(0x00, p + UART_EXAR_MPIOLVL_7_0); 288 writeb(0xc0, p + UART_EXAR_MPIOINV_7_0); 289 writeb(0xc0, p + UART_EXAR_MPIOSEL_7_0); 290 break; 291 } 292 writeb(0x00, p + UART_EXAR_MPIOINT_7_0); 293 writeb(0x00, p + UART_EXAR_MPIO3T_7_0); 294 writeb(0x00, p + UART_EXAR_MPIOOD_7_0); 295 } 296 297 return 0; 298 } 299 300 static int 301 pci_connect_tech_setup(struct exar8250 *priv, struct pci_dev *pcidev, 302 struct uart_8250_port *port, int idx) 303 { 304 unsigned int offset = idx * 0x200; 305 unsigned int baud = 1843200; 306 307 port->port.uartclk = baud * 16; 308 return default_setup(priv, pcidev, idx, offset, port); 309 } 310 311 static int 312 pci_xr17c154_setup(struct exar8250 *priv, struct pci_dev *pcidev, 313 struct uart_8250_port *port, int idx) 314 { 315 unsigned int offset = idx * 0x200; 316 unsigned int baud = 921600; 317 318 port->port.uartclk = baud * 16; 319 return default_setup(priv, pcidev, idx, offset, port); 320 } 321 322 static void setup_gpio(struct pci_dev *pcidev, u8 __iomem *p) 323 { 324 /* 325 * The Commtech adapters required the MPIOs to be driven low. The Exar 326 * devices will export them as GPIOs, so we pre-configure them safely 327 * as inputs. 328 */ 329 u8 dir = pcidev->vendor == PCI_VENDOR_ID_EXAR ? 0xff : 0x00; 330 331 writeb(0x00, p + UART_EXAR_MPIOINT_7_0); 332 writeb(0x00, p + UART_EXAR_MPIOLVL_7_0); 333 writeb(0x00, p + UART_EXAR_MPIO3T_7_0); 334 writeb(0x00, p + UART_EXAR_MPIOINV_7_0); 335 writeb(dir, p + UART_EXAR_MPIOSEL_7_0); 336 writeb(0x00, p + UART_EXAR_MPIOOD_7_0); 337 writeb(0x00, p + UART_EXAR_MPIOINT_15_8); 338 writeb(0x00, p + UART_EXAR_MPIOLVL_15_8); 339 writeb(0x00, p + UART_EXAR_MPIO3T_15_8); 340 writeb(0x00, p + UART_EXAR_MPIOINV_15_8); 341 writeb(dir, p + UART_EXAR_MPIOSEL_15_8); 342 writeb(0x00, p + UART_EXAR_MPIOOD_15_8); 343 } 344 345 static void * 346 __xr17v35x_register_gpio(struct pci_dev *pcidev, 347 const struct property_entry *properties) 348 { 349 struct platform_device *pdev; 350 351 pdev = platform_device_alloc("gpio_exar", PLATFORM_DEVID_AUTO); 352 if (!pdev) 353 return NULL; 354 355 pdev->dev.parent = &pcidev->dev; 356 ACPI_COMPANION_SET(&pdev->dev, ACPI_COMPANION(&pcidev->dev)); 357 358 if (platform_device_add_properties(pdev, properties) < 0 || 359 platform_device_add(pdev) < 0) { 360 platform_device_put(pdev); 361 return NULL; 362 } 363 364 return pdev; 365 } 366 367 static const struct property_entry exar_gpio_properties[] = { 368 PROPERTY_ENTRY_U32("exar,first-pin", 0), 369 PROPERTY_ENTRY_U32("ngpios", 16), 370 { } 371 }; 372 373 static int xr17v35x_register_gpio(struct pci_dev *pcidev, 374 struct uart_8250_port *port) 375 { 376 if (pcidev->vendor == PCI_VENDOR_ID_EXAR) 377 port->port.private_data = 378 __xr17v35x_register_gpio(pcidev, exar_gpio_properties); 379 380 return 0; 381 } 382 383 static int generic_rs485_config(struct uart_port *port, 384 struct serial_rs485 *rs485) 385 { 386 bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED); 387 u8 __iomem *p = port->membase; 388 u8 value; 389 390 value = readb(p + UART_EXAR_FCTR); 391 if (is_rs485) 392 value |= UART_FCTR_EXAR_485; 393 else 394 value &= ~UART_FCTR_EXAR_485; 395 396 writeb(value, p + UART_EXAR_FCTR); 397 398 if (is_rs485) 399 writeb(UART_EXAR_RS485_DLY(4), p + UART_MSR); 400 401 port->rs485 = *rs485; 402 403 return 0; 404 } 405 406 static const struct exar8250_platform exar8250_default_platform = { 407 .register_gpio = xr17v35x_register_gpio, 408 .rs485_config = generic_rs485_config, 409 }; 410 411 static int iot2040_rs485_config(struct uart_port *port, 412 struct serial_rs485 *rs485) 413 { 414 bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED); 415 u8 __iomem *p = port->membase; 416 u8 mask = IOT2040_UART1_MASK; 417 u8 mode, value; 418 419 if (is_rs485) { 420 if (rs485->flags & SER_RS485_RX_DURING_TX) 421 mode = IOT2040_UART_MODE_RS422; 422 else 423 mode = IOT2040_UART_MODE_RS485; 424 425 if (rs485->flags & SER_RS485_TERMINATE_BUS) 426 mode |= IOT2040_UART_TERMINATE_BUS; 427 } else { 428 mode = IOT2040_UART_MODE_RS232; 429 } 430 431 if (port->line == 3) { 432 mask <<= IOT2040_UART2_SHIFT; 433 mode <<= IOT2040_UART2_SHIFT; 434 } 435 436 value = readb(p + UART_EXAR_MPIOLVL_7_0); 437 value &= ~mask; 438 value |= mode; 439 writeb(value, p + UART_EXAR_MPIOLVL_7_0); 440 441 return generic_rs485_config(port, rs485); 442 } 443 444 static const struct property_entry iot2040_gpio_properties[] = { 445 PROPERTY_ENTRY_U32("exar,first-pin", 10), 446 PROPERTY_ENTRY_U32("ngpios", 1), 447 { } 448 }; 449 450 static int iot2040_register_gpio(struct pci_dev *pcidev, 451 struct uart_8250_port *port) 452 { 453 u8 __iomem *p = port->port.membase; 454 455 writeb(IOT2040_UARTS_DEFAULT_MODE, p + UART_EXAR_MPIOLVL_7_0); 456 writeb(IOT2040_UARTS_GPIO_LO_MODE, p + UART_EXAR_MPIOSEL_7_0); 457 writeb(IOT2040_UARTS_ENABLE, p + UART_EXAR_MPIOLVL_15_8); 458 writeb(IOT2040_UARTS_GPIO_HI_MODE, p + UART_EXAR_MPIOSEL_15_8); 459 460 port->port.private_data = 461 __xr17v35x_register_gpio(pcidev, iot2040_gpio_properties); 462 463 return 0; 464 } 465 466 static const struct exar8250_platform iot2040_platform = { 467 .rs485_config = iot2040_rs485_config, 468 .register_gpio = iot2040_register_gpio, 469 }; 470 471 /* 472 * For SIMATIC IOT2000, only IOT2040 and its variants have the Exar device, 473 * IOT2020 doesn't have. Therefore it is sufficient to match on the common 474 * board name after the device was found. 475 */ 476 static const struct dmi_system_id exar_platforms[] = { 477 { 478 .matches = { 479 DMI_EXACT_MATCH(DMI_BOARD_NAME, "SIMATIC IOT2000"), 480 }, 481 .driver_data = (void *)&iot2040_platform, 482 }, 483 {} 484 }; 485 486 static int 487 pci_xr17v35x_setup(struct exar8250 *priv, struct pci_dev *pcidev, 488 struct uart_8250_port *port, int idx) 489 { 490 const struct exar8250_platform *platform; 491 const struct dmi_system_id *dmi_match; 492 unsigned int offset = idx * 0x400; 493 unsigned int baud = 7812500; 494 u8 __iomem *p; 495 int ret; 496 497 dmi_match = dmi_first_match(exar_platforms); 498 if (dmi_match) 499 platform = dmi_match->driver_data; 500 else 501 platform = &exar8250_default_platform; 502 503 port->port.uartclk = baud * 16; 504 port->port.rs485_config = platform->rs485_config; 505 506 /* 507 * Setup the UART clock for the devices on expansion slot to 508 * half the clock speed of the main chip (which is 125MHz) 509 */ 510 if (idx >= 8) 511 port->port.uartclk /= 2; 512 513 ret = default_setup(priv, pcidev, idx, offset, port); 514 if (ret) 515 return ret; 516 517 p = port->port.membase; 518 519 writeb(0x00, p + UART_EXAR_8XMODE); 520 writeb(UART_FCTR_EXAR_TRGD, p + UART_EXAR_FCTR); 521 writeb(128, p + UART_EXAR_TXTRG); 522 writeb(128, p + UART_EXAR_RXTRG); 523 524 if (idx == 0) { 525 /* Setup Multipurpose Input/Output pins. */ 526 setup_gpio(pcidev, p); 527 528 ret = platform->register_gpio(pcidev, port); 529 } 530 531 return ret; 532 } 533 534 static void pci_xr17v35x_exit(struct pci_dev *pcidev) 535 { 536 struct exar8250 *priv = pci_get_drvdata(pcidev); 537 struct uart_8250_port *port = serial8250_get_port(priv->line[0]); 538 struct platform_device *pdev = port->port.private_data; 539 540 platform_device_unregister(pdev); 541 port->port.private_data = NULL; 542 } 543 544 static inline void exar_misc_clear(struct exar8250 *priv) 545 { 546 /* Clear all PCI interrupts by reading INT0. No effect on IIR */ 547 readb(priv->virt + UART_EXAR_INT0); 548 549 /* Clear INT0 for Expansion Interface slave ports, too */ 550 if (priv->board->num_ports > 8) 551 readb(priv->virt + 0x2000 + UART_EXAR_INT0); 552 } 553 554 /* 555 * These Exar UARTs have an extra interrupt indicator that could fire for a 556 * few interrupts that are not presented/cleared through IIR. One of which is 557 * a wakeup interrupt when coming out of sleep. These interrupts are only 558 * cleared by reading global INT0 or INT1 registers as interrupts are 559 * associated with channel 0. The INT[3:0] registers _are_ accessible from each 560 * channel's address space, but for the sake of bus efficiency we register a 561 * dedicated handler at the PCI device level to handle them. 562 */ 563 static irqreturn_t exar_misc_handler(int irq, void *data) 564 { 565 exar_misc_clear(data); 566 567 return IRQ_HANDLED; 568 } 569 570 static int 571 exar_pci_probe(struct pci_dev *pcidev, const struct pci_device_id *ent) 572 { 573 unsigned int nr_ports, i, bar = 0, maxnr; 574 struct exar8250_board *board; 575 struct uart_8250_port uart; 576 struct exar8250 *priv; 577 int rc; 578 579 board = (struct exar8250_board *)ent->driver_data; 580 if (!board) 581 return -EINVAL; 582 583 rc = pcim_enable_device(pcidev); 584 if (rc) 585 return rc; 586 587 maxnr = pci_resource_len(pcidev, bar) >> (board->reg_shift + 3); 588 589 nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f; 590 591 priv = devm_kzalloc(&pcidev->dev, struct_size(priv, line, nr_ports), GFP_KERNEL); 592 if (!priv) 593 return -ENOMEM; 594 595 priv->board = board; 596 priv->virt = pcim_iomap(pcidev, bar, 0); 597 if (!priv->virt) 598 return -ENOMEM; 599 600 pci_set_master(pcidev); 601 602 rc = pci_alloc_irq_vectors(pcidev, 1, 1, PCI_IRQ_ALL_TYPES); 603 if (rc < 0) 604 return rc; 605 606 memset(&uart, 0, sizeof(uart)); 607 uart.port.flags = UPF_SHARE_IRQ | UPF_EXAR_EFR | UPF_FIXED_TYPE | UPF_FIXED_PORT; 608 uart.port.irq = pci_irq_vector(pcidev, 0); 609 uart.port.dev = &pcidev->dev; 610 611 rc = devm_request_irq(&pcidev->dev, uart.port.irq, exar_misc_handler, 612 IRQF_SHARED, "exar_uart", priv); 613 if (rc) 614 return rc; 615 616 /* Clear interrupts */ 617 exar_misc_clear(priv); 618 619 for (i = 0; i < nr_ports && i < maxnr; i++) { 620 rc = board->setup(priv, pcidev, &uart, i); 621 if (rc) { 622 dev_err(&pcidev->dev, "Failed to setup port %u\n", i); 623 break; 624 } 625 626 dev_dbg(&pcidev->dev, "Setup PCI port: port %lx, irq %d, type %d\n", 627 uart.port.iobase, uart.port.irq, uart.port.iotype); 628 629 priv->line[i] = serial8250_register_8250_port(&uart); 630 if (priv->line[i] < 0) { 631 dev_err(&pcidev->dev, 632 "Couldn't register serial port %lx, irq %d, type %d, error %d\n", 633 uart.port.iobase, uart.port.irq, 634 uart.port.iotype, priv->line[i]); 635 break; 636 } 637 } 638 priv->nr = i; 639 pci_set_drvdata(pcidev, priv); 640 return 0; 641 } 642 643 static void exar_pci_remove(struct pci_dev *pcidev) 644 { 645 struct exar8250 *priv = pci_get_drvdata(pcidev); 646 unsigned int i; 647 648 for (i = 0; i < priv->nr; i++) 649 serial8250_unregister_port(priv->line[i]); 650 651 if (priv->board->exit) 652 priv->board->exit(pcidev); 653 } 654 655 static int __maybe_unused exar_suspend(struct device *dev) 656 { 657 struct pci_dev *pcidev = to_pci_dev(dev); 658 struct exar8250 *priv = pci_get_drvdata(pcidev); 659 unsigned int i; 660 661 for (i = 0; i < priv->nr; i++) 662 if (priv->line[i] >= 0) 663 serial8250_suspend_port(priv->line[i]); 664 665 /* Ensure that every init quirk is properly torn down */ 666 if (priv->board->exit) 667 priv->board->exit(pcidev); 668 669 return 0; 670 } 671 672 static int __maybe_unused exar_resume(struct device *dev) 673 { 674 struct exar8250 *priv = dev_get_drvdata(dev); 675 unsigned int i; 676 677 exar_misc_clear(priv); 678 679 for (i = 0; i < priv->nr; i++) 680 if (priv->line[i] >= 0) 681 serial8250_resume_port(priv->line[i]); 682 683 return 0; 684 } 685 686 static SIMPLE_DEV_PM_OPS(exar_pci_pm, exar_suspend, exar_resume); 687 688 static const struct exar8250_board acces_com_2x = { 689 .num_ports = 2, 690 .setup = pci_xr17c154_setup, 691 }; 692 693 static const struct exar8250_board acces_com_4x = { 694 .num_ports = 4, 695 .setup = pci_xr17c154_setup, 696 }; 697 698 static const struct exar8250_board acces_com_8x = { 699 .num_ports = 8, 700 .setup = pci_xr17c154_setup, 701 }; 702 703 704 static const struct exar8250_board pbn_fastcom335_2 = { 705 .num_ports = 2, 706 .setup = pci_fastcom335_setup, 707 }; 708 709 static const struct exar8250_board pbn_fastcom335_4 = { 710 .num_ports = 4, 711 .setup = pci_fastcom335_setup, 712 }; 713 714 static const struct exar8250_board pbn_fastcom335_8 = { 715 .num_ports = 8, 716 .setup = pci_fastcom335_setup, 717 }; 718 719 static const struct exar8250_board pbn_connect = { 720 .setup = pci_connect_tech_setup, 721 }; 722 723 static const struct exar8250_board pbn_exar_ibm_saturn = { 724 .num_ports = 1, 725 .setup = pci_xr17c154_setup, 726 }; 727 728 static const struct exar8250_board pbn_exar_XR17C15x = { 729 .setup = pci_xr17c154_setup, 730 }; 731 732 static const struct exar8250_board pbn_exar_XR17V35x = { 733 .setup = pci_xr17v35x_setup, 734 .exit = pci_xr17v35x_exit, 735 }; 736 737 static const struct exar8250_board pbn_exar_XR17V4358 = { 738 .num_ports = 12, 739 .setup = pci_xr17v35x_setup, 740 .exit = pci_xr17v35x_exit, 741 }; 742 743 static const struct exar8250_board pbn_exar_XR17V8358 = { 744 .num_ports = 16, 745 .setup = pci_xr17v35x_setup, 746 .exit = pci_xr17v35x_exit, 747 }; 748 749 #define CONNECT_DEVICE(devid, sdevid, bd) { \ 750 PCI_DEVICE_SUB( \ 751 PCI_VENDOR_ID_EXAR, \ 752 PCI_DEVICE_ID_EXAR_##devid, \ 753 PCI_SUBVENDOR_ID_CONNECT_TECH, \ 754 PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_##sdevid), 0, 0, \ 755 (kernel_ulong_t)&bd \ 756 } 757 758 #define EXAR_DEVICE(vend, devid, bd) { PCI_DEVICE_DATA(vend, devid, &bd) } 759 760 #define IBM_DEVICE(devid, sdevid, bd) { \ 761 PCI_DEVICE_SUB( \ 762 PCI_VENDOR_ID_EXAR, \ 763 PCI_DEVICE_ID_EXAR_##devid, \ 764 PCI_VENDOR_ID_IBM, \ 765 PCI_SUBDEVICE_ID_IBM_##sdevid), 0, 0, \ 766 (kernel_ulong_t)&bd \ 767 } 768 769 static const struct pci_device_id exar_pci_tbl[] = { 770 EXAR_DEVICE(ACCESSIO, COM_2S, acces_com_2x), 771 EXAR_DEVICE(ACCESSIO, COM_4S, acces_com_4x), 772 EXAR_DEVICE(ACCESSIO, COM_8S, acces_com_8x), 773 EXAR_DEVICE(ACCESSIO, COM232_8, acces_com_8x), 774 EXAR_DEVICE(ACCESSIO, COM_2SM, acces_com_2x), 775 EXAR_DEVICE(ACCESSIO, COM_4SM, acces_com_4x), 776 EXAR_DEVICE(ACCESSIO, COM_8SM, acces_com_8x), 777 778 CONNECT_DEVICE(XR17C152, UART_2_232, pbn_connect), 779 CONNECT_DEVICE(XR17C154, UART_4_232, pbn_connect), 780 CONNECT_DEVICE(XR17C158, UART_8_232, pbn_connect), 781 CONNECT_DEVICE(XR17C152, UART_1_1, pbn_connect), 782 CONNECT_DEVICE(XR17C154, UART_2_2, pbn_connect), 783 CONNECT_DEVICE(XR17C158, UART_4_4, pbn_connect), 784 CONNECT_DEVICE(XR17C152, UART_2, pbn_connect), 785 CONNECT_DEVICE(XR17C154, UART_4, pbn_connect), 786 CONNECT_DEVICE(XR17C158, UART_8, pbn_connect), 787 CONNECT_DEVICE(XR17C152, UART_2_485, pbn_connect), 788 CONNECT_DEVICE(XR17C154, UART_4_485, pbn_connect), 789 CONNECT_DEVICE(XR17C158, UART_8_485, pbn_connect), 790 791 IBM_DEVICE(XR17C152, SATURN_SERIAL_ONE_PORT, pbn_exar_ibm_saturn), 792 793 /* Exar Corp. XR17C15[248] Dual/Quad/Octal UART */ 794 EXAR_DEVICE(EXAR, XR17C152, pbn_exar_XR17C15x), 795 EXAR_DEVICE(EXAR, XR17C154, pbn_exar_XR17C15x), 796 EXAR_DEVICE(EXAR, XR17C158, pbn_exar_XR17C15x), 797 798 /* Exar Corp. XR17V[48]35[248] Dual/Quad/Octal/Hexa PCIe UARTs */ 799 EXAR_DEVICE(EXAR, XR17V352, pbn_exar_XR17V35x), 800 EXAR_DEVICE(EXAR, XR17V354, pbn_exar_XR17V35x), 801 EXAR_DEVICE(EXAR, XR17V358, pbn_exar_XR17V35x), 802 EXAR_DEVICE(EXAR, XR17V4358, pbn_exar_XR17V4358), 803 EXAR_DEVICE(EXAR, XR17V8358, pbn_exar_XR17V8358), 804 EXAR_DEVICE(COMMTECH, 4222PCIE, pbn_exar_XR17V35x), 805 EXAR_DEVICE(COMMTECH, 4224PCIE, pbn_exar_XR17V35x), 806 EXAR_DEVICE(COMMTECH, 4228PCIE, pbn_exar_XR17V35x), 807 808 EXAR_DEVICE(COMMTECH, 4222PCI335, pbn_fastcom335_2), 809 EXAR_DEVICE(COMMTECH, 4224PCI335, pbn_fastcom335_4), 810 EXAR_DEVICE(COMMTECH, 2324PCI335, pbn_fastcom335_4), 811 EXAR_DEVICE(COMMTECH, 2328PCI335, pbn_fastcom335_8), 812 { 0, } 813 }; 814 MODULE_DEVICE_TABLE(pci, exar_pci_tbl); 815 816 static struct pci_driver exar_pci_driver = { 817 .name = "exar_serial", 818 .probe = exar_pci_probe, 819 .remove = exar_pci_remove, 820 .driver = { 821 .pm = &exar_pci_pm, 822 }, 823 .id_table = exar_pci_tbl, 824 }; 825 module_pci_driver(exar_pci_driver); 826 827 MODULE_LICENSE("GPL"); 828 MODULE_DESCRIPTION("Exar Serial Driver"); 829 MODULE_AUTHOR("Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>"); 830