1 /* 2 * mxser.c -- MOXA Smartio/Industio family multiport serial driver. 3 * 4 * Copyright (C) 1999-2006 Moxa Technologies (support@moxa.com). 5 * Copyright (C) 2006-2008 Jiri Slaby <jirislaby@gmail.com> 6 * 7 * This code is loosely based on the 1.8 moxa driver which is based on 8 * Linux serial driver, written by Linus Torvalds, Theodore T'so and 9 * others. 10 * 11 * This program is free software; you can redistribute it and/or modify 12 * it under the terms of the GNU General Public License as published by 13 * the Free Software Foundation; either version 2 of the License, or 14 * (at your option) any later version. 15 * 16 * Fed through a cleanup, indent and remove of non 2.6 code by Alan Cox 17 * <alan@lxorguk.ukuu.org.uk>. The original 1.8 code is available on 18 * www.moxa.com. 19 * - Fixed x86_64 cleanness 20 */ 21 22 #include <linux/module.h> 23 #include <linux/errno.h> 24 #include <linux/signal.h> 25 #include <linux/sched.h> 26 #include <linux/timer.h> 27 #include <linux/interrupt.h> 28 #include <linux/tty.h> 29 #include <linux/tty_flip.h> 30 #include <linux/serial.h> 31 #include <linux/serial_reg.h> 32 #include <linux/major.h> 33 #include <linux/string.h> 34 #include <linux/fcntl.h> 35 #include <linux/ptrace.h> 36 #include <linux/ioport.h> 37 #include <linux/mm.h> 38 #include <linux/delay.h> 39 #include <linux/pci.h> 40 #include <linux/bitops.h> 41 #include <linux/slab.h> 42 #include <linux/ratelimit.h> 43 44 #include <asm/io.h> 45 #include <asm/irq.h> 46 #include <asm/uaccess.h> 47 48 #include "mxser.h" 49 50 #define MXSER_VERSION "2.0.5" /* 1.14 */ 51 #define MXSERMAJOR 174 52 53 #define MXSER_BOARDS 4 /* Max. boards */ 54 #define MXSER_PORTS_PER_BOARD 8 /* Max. ports per board */ 55 #define MXSER_PORTS (MXSER_BOARDS * MXSER_PORTS_PER_BOARD) 56 #define MXSER_ISR_PASS_LIMIT 100 57 58 /*CheckIsMoxaMust return value*/ 59 #define MOXA_OTHER_UART 0x00 60 #define MOXA_MUST_MU150_HWID 0x01 61 #define MOXA_MUST_MU860_HWID 0x02 62 63 #define WAKEUP_CHARS 256 64 65 #define UART_MCR_AFE 0x20 66 #define UART_LSR_SPECIAL 0x1E 67 68 #define PCI_DEVICE_ID_POS104UL 0x1044 69 #define PCI_DEVICE_ID_CB108 0x1080 70 #define PCI_DEVICE_ID_CP102UF 0x1023 71 #define PCI_DEVICE_ID_CP112UL 0x1120 72 #define PCI_DEVICE_ID_CB114 0x1142 73 #define PCI_DEVICE_ID_CP114UL 0x1143 74 #define PCI_DEVICE_ID_CB134I 0x1341 75 #define PCI_DEVICE_ID_CP138U 0x1380 76 77 78 #define C168_ASIC_ID 1 79 #define C104_ASIC_ID 2 80 #define C102_ASIC_ID 0xB 81 #define CI132_ASIC_ID 4 82 #define CI134_ASIC_ID 3 83 #define CI104J_ASIC_ID 5 84 85 #define MXSER_HIGHBAUD 1 86 #define MXSER_HAS2 2 87 88 /* This is only for PCI */ 89 static const struct { 90 int type; 91 int tx_fifo; 92 int rx_fifo; 93 int xmit_fifo_size; 94 int rx_high_water; 95 int rx_trigger; 96 int rx_low_water; 97 long max_baud; 98 } Gpci_uart_info[] = { 99 {MOXA_OTHER_UART, 16, 16, 16, 14, 14, 1, 921600L}, 100 {MOXA_MUST_MU150_HWID, 64, 64, 64, 48, 48, 16, 230400L}, 101 {MOXA_MUST_MU860_HWID, 128, 128, 128, 96, 96, 32, 921600L} 102 }; 103 #define UART_INFO_NUM ARRAY_SIZE(Gpci_uart_info) 104 105 struct mxser_cardinfo { 106 char *name; 107 unsigned int nports; 108 unsigned int flags; 109 }; 110 111 static const struct mxser_cardinfo mxser_cards[] = { 112 /* 0*/ { "C168 series", 8, }, 113 { "C104 series", 4, }, 114 { "CI-104J series", 4, }, 115 { "C168H/PCI series", 8, }, 116 { "C104H/PCI series", 4, }, 117 /* 5*/ { "C102 series", 4, MXSER_HAS2 }, /* C102-ISA */ 118 { "CI-132 series", 4, MXSER_HAS2 }, 119 { "CI-134 series", 4, }, 120 { "CP-132 series", 2, }, 121 { "CP-114 series", 4, }, 122 /*10*/ { "CT-114 series", 4, }, 123 { "CP-102 series", 2, MXSER_HIGHBAUD }, 124 { "CP-104U series", 4, }, 125 { "CP-168U series", 8, }, 126 { "CP-132U series", 2, }, 127 /*15*/ { "CP-134U series", 4, }, 128 { "CP-104JU series", 4, }, 129 { "Moxa UC7000 Serial", 8, }, /* RC7000 */ 130 { "CP-118U series", 8, }, 131 { "CP-102UL series", 2, }, 132 /*20*/ { "CP-102U series", 2, }, 133 { "CP-118EL series", 8, }, 134 { "CP-168EL series", 8, }, 135 { "CP-104EL series", 4, }, 136 { "CB-108 series", 8, }, 137 /*25*/ { "CB-114 series", 4, }, 138 { "CB-134I series", 4, }, 139 { "CP-138U series", 8, }, 140 { "POS-104UL series", 4, }, 141 { "CP-114UL series", 4, }, 142 /*30*/ { "CP-102UF series", 2, }, 143 { "CP-112UL series", 2, }, 144 }; 145 146 /* driver_data correspond to the lines in the structure above 147 see also ISA probe function before you change something */ 148 static struct pci_device_id mxser_pcibrds[] = { 149 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C168), .driver_data = 3 }, 150 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C104), .driver_data = 4 }, 151 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132), .driver_data = 8 }, 152 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP114), .driver_data = 9 }, 153 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CT114), .driver_data = 10 }, 154 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102), .driver_data = 11 }, 155 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104U), .driver_data = 12 }, 156 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168U), .driver_data = 13 }, 157 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132U), .driver_data = 14 }, 158 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP134U), .driver_data = 15 }, 159 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104JU),.driver_data = 16 }, 160 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_RC7000), .driver_data = 17 }, 161 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118U), .driver_data = 18 }, 162 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102UL),.driver_data = 19 }, 163 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102U), .driver_data = 20 }, 164 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118EL),.driver_data = 21 }, 165 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168EL),.driver_data = 22 }, 166 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104EL),.driver_data = 23 }, 167 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB108), .driver_data = 24 }, 168 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB114), .driver_data = 25 }, 169 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB134I), .driver_data = 26 }, 170 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP138U), .driver_data = 27 }, 171 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_POS104UL), .driver_data = 28 }, 172 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP114UL), .driver_data = 29 }, 173 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP102UF), .driver_data = 30 }, 174 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP112UL), .driver_data = 31 }, 175 { } 176 }; 177 MODULE_DEVICE_TABLE(pci, mxser_pcibrds); 178 179 static unsigned long ioaddr[MXSER_BOARDS]; 180 static int ttymajor = MXSERMAJOR; 181 182 /* Variables for insmod */ 183 184 MODULE_AUTHOR("Casper Yang"); 185 MODULE_DESCRIPTION("MOXA Smartio/Industio Family Multiport Board Device Driver"); 186 module_param_array(ioaddr, ulong, NULL, 0); 187 MODULE_PARM_DESC(ioaddr, "ISA io addresses to look for a moxa board"); 188 module_param(ttymajor, int, 0); 189 MODULE_LICENSE("GPL"); 190 191 struct mxser_log { 192 int tick; 193 unsigned long rxcnt[MXSER_PORTS]; 194 unsigned long txcnt[MXSER_PORTS]; 195 }; 196 197 struct mxser_mon { 198 unsigned long rxcnt; 199 unsigned long txcnt; 200 unsigned long up_rxcnt; 201 unsigned long up_txcnt; 202 int modem_status; 203 unsigned char hold_reason; 204 }; 205 206 struct mxser_mon_ext { 207 unsigned long rx_cnt[32]; 208 unsigned long tx_cnt[32]; 209 unsigned long up_rxcnt[32]; 210 unsigned long up_txcnt[32]; 211 int modem_status[32]; 212 213 long baudrate[32]; 214 int databits[32]; 215 int stopbits[32]; 216 int parity[32]; 217 int flowctrl[32]; 218 int fifo[32]; 219 int iftype[32]; 220 }; 221 222 struct mxser_board; 223 224 struct mxser_port { 225 struct tty_port port; 226 struct mxser_board *board; 227 228 unsigned long ioaddr; 229 unsigned long opmode_ioaddr; 230 int max_baud; 231 232 int rx_high_water; 233 int rx_trigger; /* Rx fifo trigger level */ 234 int rx_low_water; 235 int baud_base; /* max. speed */ 236 int type; /* UART type */ 237 238 int x_char; /* xon/xoff character */ 239 int IER; /* Interrupt Enable Register */ 240 int MCR; /* Modem control register */ 241 242 unsigned char stop_rx; 243 unsigned char ldisc_stop_rx; 244 245 int custom_divisor; 246 unsigned char err_shadow; 247 248 struct async_icount icount; /* kernel counters for 4 input interrupts */ 249 int timeout; 250 251 int read_status_mask; 252 int ignore_status_mask; 253 int xmit_fifo_size; 254 int xmit_head; 255 int xmit_tail; 256 int xmit_cnt; 257 int closing; 258 259 struct ktermios normal_termios; 260 261 struct mxser_mon mon_data; 262 263 spinlock_t slock; 264 }; 265 266 struct mxser_board { 267 unsigned int idx; 268 int irq; 269 const struct mxser_cardinfo *info; 270 unsigned long vector; 271 unsigned long vector_mask; 272 273 int chip_flag; 274 int uart_type; 275 276 struct mxser_port ports[MXSER_PORTS_PER_BOARD]; 277 }; 278 279 struct mxser_mstatus { 280 tcflag_t cflag; 281 int cts; 282 int dsr; 283 int ri; 284 int dcd; 285 }; 286 287 static struct mxser_board mxser_boards[MXSER_BOARDS]; 288 static struct tty_driver *mxvar_sdriver; 289 static struct mxser_log mxvar_log; 290 static int mxser_set_baud_method[MXSER_PORTS + 1]; 291 292 static void mxser_enable_must_enchance_mode(unsigned long baseio) 293 { 294 u8 oldlcr; 295 u8 efr; 296 297 oldlcr = inb(baseio + UART_LCR); 298 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 299 300 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 301 efr |= MOXA_MUST_EFR_EFRB_ENABLE; 302 303 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 304 outb(oldlcr, baseio + UART_LCR); 305 } 306 307 #ifdef CONFIG_PCI 308 static void mxser_disable_must_enchance_mode(unsigned long baseio) 309 { 310 u8 oldlcr; 311 u8 efr; 312 313 oldlcr = inb(baseio + UART_LCR); 314 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 315 316 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 317 efr &= ~MOXA_MUST_EFR_EFRB_ENABLE; 318 319 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 320 outb(oldlcr, baseio + UART_LCR); 321 } 322 #endif 323 324 static void mxser_set_must_xon1_value(unsigned long baseio, u8 value) 325 { 326 u8 oldlcr; 327 u8 efr; 328 329 oldlcr = inb(baseio + UART_LCR); 330 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 331 332 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 333 efr &= ~MOXA_MUST_EFR_BANK_MASK; 334 efr |= MOXA_MUST_EFR_BANK0; 335 336 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 337 outb(value, baseio + MOXA_MUST_XON1_REGISTER); 338 outb(oldlcr, baseio + UART_LCR); 339 } 340 341 static void mxser_set_must_xoff1_value(unsigned long baseio, u8 value) 342 { 343 u8 oldlcr; 344 u8 efr; 345 346 oldlcr = inb(baseio + UART_LCR); 347 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 348 349 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 350 efr &= ~MOXA_MUST_EFR_BANK_MASK; 351 efr |= MOXA_MUST_EFR_BANK0; 352 353 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 354 outb(value, baseio + MOXA_MUST_XOFF1_REGISTER); 355 outb(oldlcr, baseio + UART_LCR); 356 } 357 358 static void mxser_set_must_fifo_value(struct mxser_port *info) 359 { 360 u8 oldlcr; 361 u8 efr; 362 363 oldlcr = inb(info->ioaddr + UART_LCR); 364 outb(MOXA_MUST_ENTER_ENCHANCE, info->ioaddr + UART_LCR); 365 366 efr = inb(info->ioaddr + MOXA_MUST_EFR_REGISTER); 367 efr &= ~MOXA_MUST_EFR_BANK_MASK; 368 efr |= MOXA_MUST_EFR_BANK1; 369 370 outb(efr, info->ioaddr + MOXA_MUST_EFR_REGISTER); 371 outb((u8)info->rx_high_water, info->ioaddr + MOXA_MUST_RBRTH_REGISTER); 372 outb((u8)info->rx_trigger, info->ioaddr + MOXA_MUST_RBRTI_REGISTER); 373 outb((u8)info->rx_low_water, info->ioaddr + MOXA_MUST_RBRTL_REGISTER); 374 outb(oldlcr, info->ioaddr + UART_LCR); 375 } 376 377 static void mxser_set_must_enum_value(unsigned long baseio, u8 value) 378 { 379 u8 oldlcr; 380 u8 efr; 381 382 oldlcr = inb(baseio + UART_LCR); 383 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 384 385 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 386 efr &= ~MOXA_MUST_EFR_BANK_MASK; 387 efr |= MOXA_MUST_EFR_BANK2; 388 389 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 390 outb(value, baseio + MOXA_MUST_ENUM_REGISTER); 391 outb(oldlcr, baseio + UART_LCR); 392 } 393 394 #ifdef CONFIG_PCI 395 static void mxser_get_must_hardware_id(unsigned long baseio, u8 *pId) 396 { 397 u8 oldlcr; 398 u8 efr; 399 400 oldlcr = inb(baseio + UART_LCR); 401 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 402 403 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 404 efr &= ~MOXA_MUST_EFR_BANK_MASK; 405 efr |= MOXA_MUST_EFR_BANK2; 406 407 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 408 *pId = inb(baseio + MOXA_MUST_HWID_REGISTER); 409 outb(oldlcr, baseio + UART_LCR); 410 } 411 #endif 412 413 static void SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(unsigned long baseio) 414 { 415 u8 oldlcr; 416 u8 efr; 417 418 oldlcr = inb(baseio + UART_LCR); 419 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 420 421 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 422 efr &= ~MOXA_MUST_EFR_SF_MASK; 423 424 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 425 outb(oldlcr, baseio + UART_LCR); 426 } 427 428 static void mxser_enable_must_tx_software_flow_control(unsigned long baseio) 429 { 430 u8 oldlcr; 431 u8 efr; 432 433 oldlcr = inb(baseio + UART_LCR); 434 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 435 436 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 437 efr &= ~MOXA_MUST_EFR_SF_TX_MASK; 438 efr |= MOXA_MUST_EFR_SF_TX1; 439 440 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 441 outb(oldlcr, baseio + UART_LCR); 442 } 443 444 static void mxser_disable_must_tx_software_flow_control(unsigned long baseio) 445 { 446 u8 oldlcr; 447 u8 efr; 448 449 oldlcr = inb(baseio + UART_LCR); 450 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 451 452 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 453 efr &= ~MOXA_MUST_EFR_SF_TX_MASK; 454 455 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 456 outb(oldlcr, baseio + UART_LCR); 457 } 458 459 static void mxser_enable_must_rx_software_flow_control(unsigned long baseio) 460 { 461 u8 oldlcr; 462 u8 efr; 463 464 oldlcr = inb(baseio + UART_LCR); 465 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 466 467 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 468 efr &= ~MOXA_MUST_EFR_SF_RX_MASK; 469 efr |= MOXA_MUST_EFR_SF_RX1; 470 471 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 472 outb(oldlcr, baseio + UART_LCR); 473 } 474 475 static void mxser_disable_must_rx_software_flow_control(unsigned long baseio) 476 { 477 u8 oldlcr; 478 u8 efr; 479 480 oldlcr = inb(baseio + UART_LCR); 481 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR); 482 483 efr = inb(baseio + MOXA_MUST_EFR_REGISTER); 484 efr &= ~MOXA_MUST_EFR_SF_RX_MASK; 485 486 outb(efr, baseio + MOXA_MUST_EFR_REGISTER); 487 outb(oldlcr, baseio + UART_LCR); 488 } 489 490 #ifdef CONFIG_PCI 491 static int CheckIsMoxaMust(unsigned long io) 492 { 493 u8 oldmcr, hwid; 494 int i; 495 496 outb(0, io + UART_LCR); 497 mxser_disable_must_enchance_mode(io); 498 oldmcr = inb(io + UART_MCR); 499 outb(0, io + UART_MCR); 500 mxser_set_must_xon1_value(io, 0x11); 501 if ((hwid = inb(io + UART_MCR)) != 0) { 502 outb(oldmcr, io + UART_MCR); 503 return MOXA_OTHER_UART; 504 } 505 506 mxser_get_must_hardware_id(io, &hwid); 507 for (i = 1; i < UART_INFO_NUM; i++) { /* 0 = OTHER_UART */ 508 if (hwid == Gpci_uart_info[i].type) 509 return (int)hwid; 510 } 511 return MOXA_OTHER_UART; 512 } 513 #endif 514 515 static void process_txrx_fifo(struct mxser_port *info) 516 { 517 int i; 518 519 if ((info->type == PORT_16450) || (info->type == PORT_8250)) { 520 info->rx_trigger = 1; 521 info->rx_high_water = 1; 522 info->rx_low_water = 1; 523 info->xmit_fifo_size = 1; 524 } else 525 for (i = 0; i < UART_INFO_NUM; i++) 526 if (info->board->chip_flag == Gpci_uart_info[i].type) { 527 info->rx_trigger = Gpci_uart_info[i].rx_trigger; 528 info->rx_low_water = Gpci_uart_info[i].rx_low_water; 529 info->rx_high_water = Gpci_uart_info[i].rx_high_water; 530 info->xmit_fifo_size = Gpci_uart_info[i].xmit_fifo_size; 531 break; 532 } 533 } 534 535 static unsigned char mxser_get_msr(int baseaddr, int mode, int port) 536 { 537 static unsigned char mxser_msr[MXSER_PORTS + 1]; 538 unsigned char status = 0; 539 540 status = inb(baseaddr + UART_MSR); 541 542 mxser_msr[port] &= 0x0F; 543 mxser_msr[port] |= status; 544 status = mxser_msr[port]; 545 if (mode) 546 mxser_msr[port] = 0; 547 548 return status; 549 } 550 551 static int mxser_carrier_raised(struct tty_port *port) 552 { 553 struct mxser_port *mp = container_of(port, struct mxser_port, port); 554 return (inb(mp->ioaddr + UART_MSR) & UART_MSR_DCD)?1:0; 555 } 556 557 static void mxser_dtr_rts(struct tty_port *port, int on) 558 { 559 struct mxser_port *mp = container_of(port, struct mxser_port, port); 560 unsigned long flags; 561 562 spin_lock_irqsave(&mp->slock, flags); 563 if (on) 564 outb(inb(mp->ioaddr + UART_MCR) | 565 UART_MCR_DTR | UART_MCR_RTS, mp->ioaddr + UART_MCR); 566 else 567 outb(inb(mp->ioaddr + UART_MCR)&~(UART_MCR_DTR | UART_MCR_RTS), 568 mp->ioaddr + UART_MCR); 569 spin_unlock_irqrestore(&mp->slock, flags); 570 } 571 572 static int mxser_set_baud(struct tty_struct *tty, long newspd) 573 { 574 struct mxser_port *info = tty->driver_data; 575 int quot = 0, baud; 576 unsigned char cval; 577 578 if (!info->ioaddr) 579 return -1; 580 581 if (newspd > info->max_baud) 582 return -1; 583 584 if (newspd == 134) { 585 quot = 2 * info->baud_base / 269; 586 tty_encode_baud_rate(tty, 134, 134); 587 } else if (newspd) { 588 quot = info->baud_base / newspd; 589 if (quot == 0) 590 quot = 1; 591 baud = info->baud_base/quot; 592 tty_encode_baud_rate(tty, baud, baud); 593 } else { 594 quot = 0; 595 } 596 597 info->timeout = ((info->xmit_fifo_size * HZ * 10 * quot) / info->baud_base); 598 info->timeout += HZ / 50; /* Add .02 seconds of slop */ 599 600 if (quot) { 601 info->MCR |= UART_MCR_DTR; 602 outb(info->MCR, info->ioaddr + UART_MCR); 603 } else { 604 info->MCR &= ~UART_MCR_DTR; 605 outb(info->MCR, info->ioaddr + UART_MCR); 606 return 0; 607 } 608 609 cval = inb(info->ioaddr + UART_LCR); 610 611 outb(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR); /* set DLAB */ 612 613 outb(quot & 0xff, info->ioaddr + UART_DLL); /* LS of divisor */ 614 outb(quot >> 8, info->ioaddr + UART_DLM); /* MS of divisor */ 615 outb(cval, info->ioaddr + UART_LCR); /* reset DLAB */ 616 617 #ifdef BOTHER 618 if (C_BAUD(tty) == BOTHER) { 619 quot = info->baud_base % newspd; 620 quot *= 8; 621 if (quot % newspd > newspd / 2) { 622 quot /= newspd; 623 quot++; 624 } else 625 quot /= newspd; 626 627 mxser_set_must_enum_value(info->ioaddr, quot); 628 } else 629 #endif 630 mxser_set_must_enum_value(info->ioaddr, 0); 631 632 return 0; 633 } 634 635 /* 636 * This routine is called to set the UART divisor registers to match 637 * the specified baud rate for a serial port. 638 */ 639 static int mxser_change_speed(struct tty_struct *tty, 640 struct ktermios *old_termios) 641 { 642 struct mxser_port *info = tty->driver_data; 643 unsigned cflag, cval, fcr; 644 int ret = 0; 645 unsigned char status; 646 647 cflag = tty->termios.c_cflag; 648 if (!info->ioaddr) 649 return ret; 650 651 if (mxser_set_baud_method[tty->index] == 0) 652 mxser_set_baud(tty, tty_get_baud_rate(tty)); 653 654 /* byte size and parity */ 655 switch (cflag & CSIZE) { 656 case CS5: 657 cval = 0x00; 658 break; 659 case CS6: 660 cval = 0x01; 661 break; 662 case CS7: 663 cval = 0x02; 664 break; 665 case CS8: 666 cval = 0x03; 667 break; 668 default: 669 cval = 0x00; 670 break; /* too keep GCC shut... */ 671 } 672 if (cflag & CSTOPB) 673 cval |= 0x04; 674 if (cflag & PARENB) 675 cval |= UART_LCR_PARITY; 676 if (!(cflag & PARODD)) 677 cval |= UART_LCR_EPAR; 678 if (cflag & CMSPAR) 679 cval |= UART_LCR_SPAR; 680 681 if ((info->type == PORT_8250) || (info->type == PORT_16450)) { 682 if (info->board->chip_flag) { 683 fcr = UART_FCR_ENABLE_FIFO; 684 fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE; 685 mxser_set_must_fifo_value(info); 686 } else 687 fcr = 0; 688 } else { 689 fcr = UART_FCR_ENABLE_FIFO; 690 if (info->board->chip_flag) { 691 fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE; 692 mxser_set_must_fifo_value(info); 693 } else { 694 switch (info->rx_trigger) { 695 case 1: 696 fcr |= UART_FCR_TRIGGER_1; 697 break; 698 case 4: 699 fcr |= UART_FCR_TRIGGER_4; 700 break; 701 case 8: 702 fcr |= UART_FCR_TRIGGER_8; 703 break; 704 default: 705 fcr |= UART_FCR_TRIGGER_14; 706 break; 707 } 708 } 709 } 710 711 /* CTS flow control flag and modem status interrupts */ 712 info->IER &= ~UART_IER_MSI; 713 info->MCR &= ~UART_MCR_AFE; 714 tty_port_set_cts_flow(&info->port, cflag & CRTSCTS); 715 if (cflag & CRTSCTS) { 716 info->IER |= UART_IER_MSI; 717 if ((info->type == PORT_16550A) || (info->board->chip_flag)) { 718 info->MCR |= UART_MCR_AFE; 719 } else { 720 status = inb(info->ioaddr + UART_MSR); 721 if (tty->hw_stopped) { 722 if (status & UART_MSR_CTS) { 723 tty->hw_stopped = 0; 724 if (info->type != PORT_16550A && 725 !info->board->chip_flag) { 726 outb(info->IER & ~UART_IER_THRI, 727 info->ioaddr + 728 UART_IER); 729 info->IER |= UART_IER_THRI; 730 outb(info->IER, info->ioaddr + 731 UART_IER); 732 } 733 tty_wakeup(tty); 734 } 735 } else { 736 if (!(status & UART_MSR_CTS)) { 737 tty->hw_stopped = 1; 738 if ((info->type != PORT_16550A) && 739 (!info->board->chip_flag)) { 740 info->IER &= ~UART_IER_THRI; 741 outb(info->IER, info->ioaddr + 742 UART_IER); 743 } 744 } 745 } 746 } 747 } 748 outb(info->MCR, info->ioaddr + UART_MCR); 749 tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL); 750 if (~cflag & CLOCAL) 751 info->IER |= UART_IER_MSI; 752 outb(info->IER, info->ioaddr + UART_IER); 753 754 /* 755 * Set up parity check flag 756 */ 757 info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; 758 if (I_INPCK(tty)) 759 info->read_status_mask |= UART_LSR_FE | UART_LSR_PE; 760 if (I_BRKINT(tty) || I_PARMRK(tty)) 761 info->read_status_mask |= UART_LSR_BI; 762 763 info->ignore_status_mask = 0; 764 765 if (I_IGNBRK(tty)) { 766 info->ignore_status_mask |= UART_LSR_BI; 767 info->read_status_mask |= UART_LSR_BI; 768 /* 769 * If we're ignore parity and break indicators, ignore 770 * overruns too. (For real raw support). 771 */ 772 if (I_IGNPAR(tty)) { 773 info->ignore_status_mask |= 774 UART_LSR_OE | 775 UART_LSR_PE | 776 UART_LSR_FE; 777 info->read_status_mask |= 778 UART_LSR_OE | 779 UART_LSR_PE | 780 UART_LSR_FE; 781 } 782 } 783 if (info->board->chip_flag) { 784 mxser_set_must_xon1_value(info->ioaddr, START_CHAR(tty)); 785 mxser_set_must_xoff1_value(info->ioaddr, STOP_CHAR(tty)); 786 if (I_IXON(tty)) { 787 mxser_enable_must_rx_software_flow_control( 788 info->ioaddr); 789 } else { 790 mxser_disable_must_rx_software_flow_control( 791 info->ioaddr); 792 } 793 if (I_IXOFF(tty)) { 794 mxser_enable_must_tx_software_flow_control( 795 info->ioaddr); 796 } else { 797 mxser_disable_must_tx_software_flow_control( 798 info->ioaddr); 799 } 800 } 801 802 803 outb(fcr, info->ioaddr + UART_FCR); /* set fcr */ 804 outb(cval, info->ioaddr + UART_LCR); 805 806 return ret; 807 } 808 809 static void mxser_check_modem_status(struct tty_struct *tty, 810 struct mxser_port *port, int status) 811 { 812 /* update input line counters */ 813 if (status & UART_MSR_TERI) 814 port->icount.rng++; 815 if (status & UART_MSR_DDSR) 816 port->icount.dsr++; 817 if (status & UART_MSR_DDCD) 818 port->icount.dcd++; 819 if (status & UART_MSR_DCTS) 820 port->icount.cts++; 821 port->mon_data.modem_status = status; 822 wake_up_interruptible(&port->port.delta_msr_wait); 823 824 if (tty_port_check_carrier(&port->port) && (status & UART_MSR_DDCD)) { 825 if (status & UART_MSR_DCD) 826 wake_up_interruptible(&port->port.open_wait); 827 } 828 829 if (tty_port_cts_enabled(&port->port)) { 830 if (tty->hw_stopped) { 831 if (status & UART_MSR_CTS) { 832 tty->hw_stopped = 0; 833 834 if ((port->type != PORT_16550A) && 835 (!port->board->chip_flag)) { 836 outb(port->IER & ~UART_IER_THRI, 837 port->ioaddr + UART_IER); 838 port->IER |= UART_IER_THRI; 839 outb(port->IER, port->ioaddr + 840 UART_IER); 841 } 842 tty_wakeup(tty); 843 } 844 } else { 845 if (!(status & UART_MSR_CTS)) { 846 tty->hw_stopped = 1; 847 if (port->type != PORT_16550A && 848 !port->board->chip_flag) { 849 port->IER &= ~UART_IER_THRI; 850 outb(port->IER, port->ioaddr + 851 UART_IER); 852 } 853 } 854 } 855 } 856 } 857 858 static int mxser_activate(struct tty_port *port, struct tty_struct *tty) 859 { 860 struct mxser_port *info = container_of(port, struct mxser_port, port); 861 unsigned long page; 862 unsigned long flags; 863 864 page = __get_free_page(GFP_KERNEL); 865 if (!page) 866 return -ENOMEM; 867 868 spin_lock_irqsave(&info->slock, flags); 869 870 if (!info->ioaddr || !info->type) { 871 set_bit(TTY_IO_ERROR, &tty->flags); 872 free_page(page); 873 spin_unlock_irqrestore(&info->slock, flags); 874 return 0; 875 } 876 info->port.xmit_buf = (unsigned char *) page; 877 878 /* 879 * Clear the FIFO buffers and disable them 880 * (they will be reenabled in mxser_change_speed()) 881 */ 882 if (info->board->chip_flag) 883 outb((UART_FCR_CLEAR_RCVR | 884 UART_FCR_CLEAR_XMIT | 885 MOXA_MUST_FCR_GDA_MODE_ENABLE), info->ioaddr + UART_FCR); 886 else 887 outb((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT), 888 info->ioaddr + UART_FCR); 889 890 /* 891 * At this point there's no way the LSR could still be 0xFF; 892 * if it is, then bail out, because there's likely no UART 893 * here. 894 */ 895 if (inb(info->ioaddr + UART_LSR) == 0xff) { 896 spin_unlock_irqrestore(&info->slock, flags); 897 if (capable(CAP_SYS_ADMIN)) { 898 set_bit(TTY_IO_ERROR, &tty->flags); 899 return 0; 900 } else 901 return -ENODEV; 902 } 903 904 /* 905 * Clear the interrupt registers. 906 */ 907 (void) inb(info->ioaddr + UART_LSR); 908 (void) inb(info->ioaddr + UART_RX); 909 (void) inb(info->ioaddr + UART_IIR); 910 (void) inb(info->ioaddr + UART_MSR); 911 912 /* 913 * Now, initialize the UART 914 */ 915 outb(UART_LCR_WLEN8, info->ioaddr + UART_LCR); /* reset DLAB */ 916 info->MCR = UART_MCR_DTR | UART_MCR_RTS; 917 outb(info->MCR, info->ioaddr + UART_MCR); 918 919 /* 920 * Finally, enable interrupts 921 */ 922 info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI; 923 924 if (info->board->chip_flag) 925 info->IER |= MOXA_MUST_IER_EGDAI; 926 outb(info->IER, info->ioaddr + UART_IER); /* enable interrupts */ 927 928 /* 929 * And clear the interrupt registers again for luck. 930 */ 931 (void) inb(info->ioaddr + UART_LSR); 932 (void) inb(info->ioaddr + UART_RX); 933 (void) inb(info->ioaddr + UART_IIR); 934 (void) inb(info->ioaddr + UART_MSR); 935 936 clear_bit(TTY_IO_ERROR, &tty->flags); 937 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; 938 939 /* 940 * and set the speed of the serial port 941 */ 942 mxser_change_speed(tty, NULL); 943 spin_unlock_irqrestore(&info->slock, flags); 944 945 return 0; 946 } 947 948 /* 949 * This routine will shutdown a serial port 950 */ 951 static void mxser_shutdown_port(struct tty_port *port) 952 { 953 struct mxser_port *info = container_of(port, struct mxser_port, port); 954 unsigned long flags; 955 956 spin_lock_irqsave(&info->slock, flags); 957 958 /* 959 * clear delta_msr_wait queue to avoid mem leaks: we may free the irq 960 * here so the queue might never be waken up 961 */ 962 wake_up_interruptible(&info->port.delta_msr_wait); 963 964 /* 965 * Free the xmit buffer, if necessary 966 */ 967 if (info->port.xmit_buf) { 968 free_page((unsigned long) info->port.xmit_buf); 969 info->port.xmit_buf = NULL; 970 } 971 972 info->IER = 0; 973 outb(0x00, info->ioaddr + UART_IER); 974 975 /* clear Rx/Tx FIFO's */ 976 if (info->board->chip_flag) 977 outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT | 978 MOXA_MUST_FCR_GDA_MODE_ENABLE, 979 info->ioaddr + UART_FCR); 980 else 981 outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT, 982 info->ioaddr + UART_FCR); 983 984 /* read data port to reset things */ 985 (void) inb(info->ioaddr + UART_RX); 986 987 988 if (info->board->chip_flag) 989 SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(info->ioaddr); 990 991 spin_unlock_irqrestore(&info->slock, flags); 992 } 993 994 /* 995 * This routine is called whenever a serial port is opened. It 996 * enables interrupts for a serial port, linking in its async structure into 997 * the IRQ chain. It also performs the serial-specific 998 * initialization for the tty structure. 999 */ 1000 static int mxser_open(struct tty_struct *tty, struct file *filp) 1001 { 1002 struct mxser_port *info; 1003 int line; 1004 1005 line = tty->index; 1006 if (line == MXSER_PORTS) 1007 return 0; 1008 info = &mxser_boards[line / MXSER_PORTS_PER_BOARD].ports[line % MXSER_PORTS_PER_BOARD]; 1009 if (!info->ioaddr) 1010 return -ENODEV; 1011 1012 tty->driver_data = info; 1013 return tty_port_open(&info->port, tty, filp); 1014 } 1015 1016 static void mxser_flush_buffer(struct tty_struct *tty) 1017 { 1018 struct mxser_port *info = tty->driver_data; 1019 char fcr; 1020 unsigned long flags; 1021 1022 1023 spin_lock_irqsave(&info->slock, flags); 1024 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; 1025 1026 fcr = inb(info->ioaddr + UART_FCR); 1027 outb((fcr | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT), 1028 info->ioaddr + UART_FCR); 1029 outb(fcr, info->ioaddr + UART_FCR); 1030 1031 spin_unlock_irqrestore(&info->slock, flags); 1032 1033 tty_wakeup(tty); 1034 } 1035 1036 1037 static void mxser_close_port(struct tty_port *port) 1038 { 1039 struct mxser_port *info = container_of(port, struct mxser_port, port); 1040 unsigned long timeout; 1041 /* 1042 * At this point we stop accepting input. To do this, we 1043 * disable the receive line status interrupts, and tell the 1044 * interrupt driver to stop checking the data ready bit in the 1045 * line status register. 1046 */ 1047 info->IER &= ~UART_IER_RLSI; 1048 if (info->board->chip_flag) 1049 info->IER &= ~MOXA_MUST_RECV_ISR; 1050 1051 outb(info->IER, info->ioaddr + UART_IER); 1052 /* 1053 * Before we drop DTR, make sure the UART transmitter 1054 * has completely drained; this is especially 1055 * important if there is a transmit FIFO! 1056 */ 1057 timeout = jiffies + HZ; 1058 while (!(inb(info->ioaddr + UART_LSR) & UART_LSR_TEMT)) { 1059 schedule_timeout_interruptible(5); 1060 if (time_after(jiffies, timeout)) 1061 break; 1062 } 1063 } 1064 1065 /* 1066 * This routine is called when the serial port gets closed. First, we 1067 * wait for the last remaining data to be sent. Then, we unlink its 1068 * async structure from the interrupt chain if necessary, and we free 1069 * that IRQ if nothing is left in the chain. 1070 */ 1071 static void mxser_close(struct tty_struct *tty, struct file *filp) 1072 { 1073 struct mxser_port *info = tty->driver_data; 1074 struct tty_port *port = &info->port; 1075 1076 if (tty->index == MXSER_PORTS || info == NULL) 1077 return; 1078 if (tty_port_close_start(port, tty, filp) == 0) 1079 return; 1080 info->closing = 1; 1081 mutex_lock(&port->mutex); 1082 mxser_close_port(port); 1083 mxser_flush_buffer(tty); 1084 if (tty_port_initialized(port) && C_HUPCL(tty)) 1085 tty_port_lower_dtr_rts(port); 1086 mxser_shutdown_port(port); 1087 tty_port_set_initialized(port, 0); 1088 mutex_unlock(&port->mutex); 1089 info->closing = 0; 1090 /* Right now the tty_port set is done outside of the close_end helper 1091 as we don't yet have everyone using refcounts */ 1092 tty_port_close_end(port, tty); 1093 tty_port_tty_set(port, NULL); 1094 } 1095 1096 static int mxser_write(struct tty_struct *tty, const unsigned char *buf, int count) 1097 { 1098 int c, total = 0; 1099 struct mxser_port *info = tty->driver_data; 1100 unsigned long flags; 1101 1102 if (!info->port.xmit_buf) 1103 return 0; 1104 1105 while (1) { 1106 c = min_t(int, count, min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1, 1107 SERIAL_XMIT_SIZE - info->xmit_head)); 1108 if (c <= 0) 1109 break; 1110 1111 memcpy(info->port.xmit_buf + info->xmit_head, buf, c); 1112 spin_lock_irqsave(&info->slock, flags); 1113 info->xmit_head = (info->xmit_head + c) & 1114 (SERIAL_XMIT_SIZE - 1); 1115 info->xmit_cnt += c; 1116 spin_unlock_irqrestore(&info->slock, flags); 1117 1118 buf += c; 1119 count -= c; 1120 total += c; 1121 } 1122 1123 if (info->xmit_cnt && !tty->stopped) { 1124 if (!tty->hw_stopped || 1125 (info->type == PORT_16550A) || 1126 (info->board->chip_flag)) { 1127 spin_lock_irqsave(&info->slock, flags); 1128 outb(info->IER & ~UART_IER_THRI, info->ioaddr + 1129 UART_IER); 1130 info->IER |= UART_IER_THRI; 1131 outb(info->IER, info->ioaddr + UART_IER); 1132 spin_unlock_irqrestore(&info->slock, flags); 1133 } 1134 } 1135 return total; 1136 } 1137 1138 static int mxser_put_char(struct tty_struct *tty, unsigned char ch) 1139 { 1140 struct mxser_port *info = tty->driver_data; 1141 unsigned long flags; 1142 1143 if (!info->port.xmit_buf) 1144 return 0; 1145 1146 if (info->xmit_cnt >= SERIAL_XMIT_SIZE - 1) 1147 return 0; 1148 1149 spin_lock_irqsave(&info->slock, flags); 1150 info->port.xmit_buf[info->xmit_head++] = ch; 1151 info->xmit_head &= SERIAL_XMIT_SIZE - 1; 1152 info->xmit_cnt++; 1153 spin_unlock_irqrestore(&info->slock, flags); 1154 if (!tty->stopped) { 1155 if (!tty->hw_stopped || 1156 (info->type == PORT_16550A) || 1157 info->board->chip_flag) { 1158 spin_lock_irqsave(&info->slock, flags); 1159 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER); 1160 info->IER |= UART_IER_THRI; 1161 outb(info->IER, info->ioaddr + UART_IER); 1162 spin_unlock_irqrestore(&info->slock, flags); 1163 } 1164 } 1165 return 1; 1166 } 1167 1168 1169 static void mxser_flush_chars(struct tty_struct *tty) 1170 { 1171 struct mxser_port *info = tty->driver_data; 1172 unsigned long flags; 1173 1174 if (info->xmit_cnt <= 0 || tty->stopped || !info->port.xmit_buf || 1175 (tty->hw_stopped && info->type != PORT_16550A && 1176 !info->board->chip_flag)) 1177 return; 1178 1179 spin_lock_irqsave(&info->slock, flags); 1180 1181 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER); 1182 info->IER |= UART_IER_THRI; 1183 outb(info->IER, info->ioaddr + UART_IER); 1184 1185 spin_unlock_irqrestore(&info->slock, flags); 1186 } 1187 1188 static int mxser_write_room(struct tty_struct *tty) 1189 { 1190 struct mxser_port *info = tty->driver_data; 1191 int ret; 1192 1193 ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1; 1194 return ret < 0 ? 0 : ret; 1195 } 1196 1197 static int mxser_chars_in_buffer(struct tty_struct *tty) 1198 { 1199 struct mxser_port *info = tty->driver_data; 1200 return info->xmit_cnt; 1201 } 1202 1203 /* 1204 * ------------------------------------------------------------ 1205 * friends of mxser_ioctl() 1206 * ------------------------------------------------------------ 1207 */ 1208 static int mxser_get_serial_info(struct tty_struct *tty, 1209 struct serial_struct __user *retinfo) 1210 { 1211 struct mxser_port *info = tty->driver_data; 1212 struct serial_struct tmp = { 1213 .type = info->type, 1214 .line = tty->index, 1215 .port = info->ioaddr, 1216 .irq = info->board->irq, 1217 .flags = info->port.flags, 1218 .baud_base = info->baud_base, 1219 .close_delay = info->port.close_delay, 1220 .closing_wait = info->port.closing_wait, 1221 .custom_divisor = info->custom_divisor, 1222 .hub6 = 0 1223 }; 1224 if (copy_to_user(retinfo, &tmp, sizeof(*retinfo))) 1225 return -EFAULT; 1226 return 0; 1227 } 1228 1229 static int mxser_set_serial_info(struct tty_struct *tty, 1230 struct serial_struct __user *new_info) 1231 { 1232 struct mxser_port *info = tty->driver_data; 1233 struct tty_port *port = &info->port; 1234 struct serial_struct new_serial; 1235 speed_t baud; 1236 unsigned long sl_flags; 1237 unsigned int flags; 1238 int retval = 0; 1239 1240 if (!new_info || !info->ioaddr) 1241 return -ENODEV; 1242 if (copy_from_user(&new_serial, new_info, sizeof(new_serial))) 1243 return -EFAULT; 1244 1245 if (new_serial.irq != info->board->irq || 1246 new_serial.port != info->ioaddr) 1247 return -EINVAL; 1248 1249 flags = port->flags & ASYNC_SPD_MASK; 1250 1251 if (!capable(CAP_SYS_ADMIN)) { 1252 if ((new_serial.baud_base != info->baud_base) || 1253 (new_serial.close_delay != info->port.close_delay) || 1254 ((new_serial.flags & ~ASYNC_USR_MASK) != (info->port.flags & ~ASYNC_USR_MASK))) 1255 return -EPERM; 1256 info->port.flags = ((info->port.flags & ~ASYNC_USR_MASK) | 1257 (new_serial.flags & ASYNC_USR_MASK)); 1258 } else { 1259 /* 1260 * OK, past this point, all the error checking has been done. 1261 * At this point, we start making changes..... 1262 */ 1263 port->flags = ((port->flags & ~ASYNC_FLAGS) | 1264 (new_serial.flags & ASYNC_FLAGS)); 1265 port->close_delay = new_serial.close_delay * HZ / 100; 1266 port->closing_wait = new_serial.closing_wait * HZ / 100; 1267 port->low_latency = (port->flags & ASYNC_LOW_LATENCY) ? 1 : 0; 1268 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST && 1269 (new_serial.baud_base != info->baud_base || 1270 new_serial.custom_divisor != 1271 info->custom_divisor)) { 1272 if (new_serial.custom_divisor == 0) 1273 return -EINVAL; 1274 baud = new_serial.baud_base / new_serial.custom_divisor; 1275 tty_encode_baud_rate(tty, baud, baud); 1276 } 1277 } 1278 1279 info->type = new_serial.type; 1280 1281 process_txrx_fifo(info); 1282 1283 if (tty_port_initialized(port)) { 1284 if (flags != (port->flags & ASYNC_SPD_MASK)) { 1285 spin_lock_irqsave(&info->slock, sl_flags); 1286 mxser_change_speed(tty, NULL); 1287 spin_unlock_irqrestore(&info->slock, sl_flags); 1288 } 1289 } else { 1290 retval = mxser_activate(port, tty); 1291 if (retval == 0) 1292 tty_port_set_initialized(port, 1); 1293 } 1294 return retval; 1295 } 1296 1297 /* 1298 * mxser_get_lsr_info - get line status register info 1299 * 1300 * Purpose: Let user call ioctl() to get info when the UART physically 1301 * is emptied. On bus types like RS485, the transmitter must 1302 * release the bus after transmitting. This must be done when 1303 * the transmit shift register is empty, not be done when the 1304 * transmit holding register is empty. This functionality 1305 * allows an RS485 driver to be written in user space. 1306 */ 1307 static int mxser_get_lsr_info(struct mxser_port *info, 1308 unsigned int __user *value) 1309 { 1310 unsigned char status; 1311 unsigned int result; 1312 unsigned long flags; 1313 1314 spin_lock_irqsave(&info->slock, flags); 1315 status = inb(info->ioaddr + UART_LSR); 1316 spin_unlock_irqrestore(&info->slock, flags); 1317 result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0); 1318 return put_user(result, value); 1319 } 1320 1321 static int mxser_tiocmget(struct tty_struct *tty) 1322 { 1323 struct mxser_port *info = tty->driver_data; 1324 unsigned char control, status; 1325 unsigned long flags; 1326 1327 1328 if (tty->index == MXSER_PORTS) 1329 return -ENOIOCTLCMD; 1330 if (tty_io_error(tty)) 1331 return -EIO; 1332 1333 control = info->MCR; 1334 1335 spin_lock_irqsave(&info->slock, flags); 1336 status = inb(info->ioaddr + UART_MSR); 1337 if (status & UART_MSR_ANY_DELTA) 1338 mxser_check_modem_status(tty, info, status); 1339 spin_unlock_irqrestore(&info->slock, flags); 1340 return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) | 1341 ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) | 1342 ((status & UART_MSR_DCD) ? TIOCM_CAR : 0) | 1343 ((status & UART_MSR_RI) ? TIOCM_RNG : 0) | 1344 ((status & UART_MSR_DSR) ? TIOCM_DSR : 0) | 1345 ((status & UART_MSR_CTS) ? TIOCM_CTS : 0); 1346 } 1347 1348 static int mxser_tiocmset(struct tty_struct *tty, 1349 unsigned int set, unsigned int clear) 1350 { 1351 struct mxser_port *info = tty->driver_data; 1352 unsigned long flags; 1353 1354 1355 if (tty->index == MXSER_PORTS) 1356 return -ENOIOCTLCMD; 1357 if (tty_io_error(tty)) 1358 return -EIO; 1359 1360 spin_lock_irqsave(&info->slock, flags); 1361 1362 if (set & TIOCM_RTS) 1363 info->MCR |= UART_MCR_RTS; 1364 if (set & TIOCM_DTR) 1365 info->MCR |= UART_MCR_DTR; 1366 1367 if (clear & TIOCM_RTS) 1368 info->MCR &= ~UART_MCR_RTS; 1369 if (clear & TIOCM_DTR) 1370 info->MCR &= ~UART_MCR_DTR; 1371 1372 outb(info->MCR, info->ioaddr + UART_MCR); 1373 spin_unlock_irqrestore(&info->slock, flags); 1374 return 0; 1375 } 1376 1377 static int __init mxser_program_mode(int port) 1378 { 1379 int id, i, j, n; 1380 1381 outb(0, port); 1382 outb(0, port); 1383 outb(0, port); 1384 (void)inb(port); 1385 (void)inb(port); 1386 outb(0, port); 1387 (void)inb(port); 1388 1389 id = inb(port + 1) & 0x1F; 1390 if ((id != C168_ASIC_ID) && 1391 (id != C104_ASIC_ID) && 1392 (id != C102_ASIC_ID) && 1393 (id != CI132_ASIC_ID) && 1394 (id != CI134_ASIC_ID) && 1395 (id != CI104J_ASIC_ID)) 1396 return -1; 1397 for (i = 0, j = 0; i < 4; i++) { 1398 n = inb(port + 2); 1399 if (n == 'M') { 1400 j = 1; 1401 } else if ((j == 1) && (n == 1)) { 1402 j = 2; 1403 break; 1404 } else 1405 j = 0; 1406 } 1407 if (j != 2) 1408 id = -2; 1409 return id; 1410 } 1411 1412 static void __init mxser_normal_mode(int port) 1413 { 1414 int i, n; 1415 1416 outb(0xA5, port + 1); 1417 outb(0x80, port + 3); 1418 outb(12, port + 0); /* 9600 bps */ 1419 outb(0, port + 1); 1420 outb(0x03, port + 3); /* 8 data bits */ 1421 outb(0x13, port + 4); /* loop back mode */ 1422 for (i = 0; i < 16; i++) { 1423 n = inb(port + 5); 1424 if ((n & 0x61) == 0x60) 1425 break; 1426 if ((n & 1) == 1) 1427 (void)inb(port); 1428 } 1429 outb(0x00, port + 4); 1430 } 1431 1432 #define CHIP_SK 0x01 /* Serial Data Clock in Eprom */ 1433 #define CHIP_DO 0x02 /* Serial Data Output in Eprom */ 1434 #define CHIP_CS 0x04 /* Serial Chip Select in Eprom */ 1435 #define CHIP_DI 0x08 /* Serial Data Input in Eprom */ 1436 #define EN_CCMD 0x000 /* Chip's command register */ 1437 #define EN0_RSARLO 0x008 /* Remote start address reg 0 */ 1438 #define EN0_RSARHI 0x009 /* Remote start address reg 1 */ 1439 #define EN0_RCNTLO 0x00A /* Remote byte count reg WR */ 1440 #define EN0_RCNTHI 0x00B /* Remote byte count reg WR */ 1441 #define EN0_DCFG 0x00E /* Data configuration reg WR */ 1442 #define EN0_PORT 0x010 /* Rcv missed frame error counter RD */ 1443 #define ENC_PAGE0 0x000 /* Select page 0 of chip registers */ 1444 #define ENC_PAGE3 0x0C0 /* Select page 3 of chip registers */ 1445 static int __init mxser_read_register(int port, unsigned short *regs) 1446 { 1447 int i, k, value, id; 1448 unsigned int j; 1449 1450 id = mxser_program_mode(port); 1451 if (id < 0) 1452 return id; 1453 for (i = 0; i < 14; i++) { 1454 k = (i & 0x3F) | 0x180; 1455 for (j = 0x100; j > 0; j >>= 1) { 1456 outb(CHIP_CS, port); 1457 if (k & j) { 1458 outb(CHIP_CS | CHIP_DO, port); 1459 outb(CHIP_CS | CHIP_DO | CHIP_SK, port); /* A? bit of read */ 1460 } else { 1461 outb(CHIP_CS, port); 1462 outb(CHIP_CS | CHIP_SK, port); /* A? bit of read */ 1463 } 1464 } 1465 (void)inb(port); 1466 value = 0; 1467 for (k = 0, j = 0x8000; k < 16; k++, j >>= 1) { 1468 outb(CHIP_CS, port); 1469 outb(CHIP_CS | CHIP_SK, port); 1470 if (inb(port) & CHIP_DI) 1471 value |= j; 1472 } 1473 regs[i] = value; 1474 outb(0, port); 1475 } 1476 mxser_normal_mode(port); 1477 return id; 1478 } 1479 1480 static int mxser_ioctl_special(unsigned int cmd, void __user *argp) 1481 { 1482 struct mxser_port *ip; 1483 struct tty_port *port; 1484 struct tty_struct *tty; 1485 int result, status; 1486 unsigned int i, j; 1487 int ret = 0; 1488 1489 switch (cmd) { 1490 case MOXA_GET_MAJOR: 1491 printk_ratelimited(KERN_WARNING "mxser: '%s' uses deprecated ioctl " 1492 "%x (GET_MAJOR), fix your userspace\n", 1493 current->comm, cmd); 1494 return put_user(ttymajor, (int __user *)argp); 1495 1496 case MOXA_CHKPORTENABLE: 1497 result = 0; 1498 for (i = 0; i < MXSER_BOARDS; i++) 1499 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++) 1500 if (mxser_boards[i].ports[j].ioaddr) 1501 result |= (1 << i); 1502 return put_user(result, (unsigned long __user *)argp); 1503 case MOXA_GETDATACOUNT: 1504 /* The receive side is locked by port->slock but it isn't 1505 clear that an exact snapshot is worth copying here */ 1506 if (copy_to_user(argp, &mxvar_log, sizeof(mxvar_log))) 1507 ret = -EFAULT; 1508 return ret; 1509 case MOXA_GETMSTATUS: { 1510 struct mxser_mstatus ms, __user *msu = argp; 1511 for (i = 0; i < MXSER_BOARDS; i++) 1512 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++) { 1513 ip = &mxser_boards[i].ports[j]; 1514 port = &ip->port; 1515 memset(&ms, 0, sizeof(ms)); 1516 1517 mutex_lock(&port->mutex); 1518 if (!ip->ioaddr) 1519 goto copy; 1520 1521 tty = tty_port_tty_get(port); 1522 1523 if (!tty) 1524 ms.cflag = ip->normal_termios.c_cflag; 1525 else 1526 ms.cflag = tty->termios.c_cflag; 1527 tty_kref_put(tty); 1528 spin_lock_irq(&ip->slock); 1529 status = inb(ip->ioaddr + UART_MSR); 1530 spin_unlock_irq(&ip->slock); 1531 if (status & UART_MSR_DCD) 1532 ms.dcd = 1; 1533 if (status & UART_MSR_DSR) 1534 ms.dsr = 1; 1535 if (status & UART_MSR_CTS) 1536 ms.cts = 1; 1537 copy: 1538 mutex_unlock(&port->mutex); 1539 if (copy_to_user(msu, &ms, sizeof(ms))) 1540 return -EFAULT; 1541 msu++; 1542 } 1543 return 0; 1544 } 1545 case MOXA_ASPP_MON_EXT: { 1546 struct mxser_mon_ext *me; /* it's 2k, stack unfriendly */ 1547 unsigned int cflag, iflag, p; 1548 u8 opmode; 1549 1550 me = kzalloc(sizeof(*me), GFP_KERNEL); 1551 if (!me) 1552 return -ENOMEM; 1553 1554 for (i = 0, p = 0; i < MXSER_BOARDS; i++) { 1555 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++, p++) { 1556 if (p >= ARRAY_SIZE(me->rx_cnt)) { 1557 i = MXSER_BOARDS; 1558 break; 1559 } 1560 ip = &mxser_boards[i].ports[j]; 1561 port = &ip->port; 1562 1563 mutex_lock(&port->mutex); 1564 if (!ip->ioaddr) { 1565 mutex_unlock(&port->mutex); 1566 continue; 1567 } 1568 1569 spin_lock_irq(&ip->slock); 1570 status = mxser_get_msr(ip->ioaddr, 0, p); 1571 1572 if (status & UART_MSR_TERI) 1573 ip->icount.rng++; 1574 if (status & UART_MSR_DDSR) 1575 ip->icount.dsr++; 1576 if (status & UART_MSR_DDCD) 1577 ip->icount.dcd++; 1578 if (status & UART_MSR_DCTS) 1579 ip->icount.cts++; 1580 1581 ip->mon_data.modem_status = status; 1582 me->rx_cnt[p] = ip->mon_data.rxcnt; 1583 me->tx_cnt[p] = ip->mon_data.txcnt; 1584 me->up_rxcnt[p] = ip->mon_data.up_rxcnt; 1585 me->up_txcnt[p] = ip->mon_data.up_txcnt; 1586 me->modem_status[p] = 1587 ip->mon_data.modem_status; 1588 spin_unlock_irq(&ip->slock); 1589 1590 tty = tty_port_tty_get(&ip->port); 1591 1592 if (!tty) { 1593 cflag = ip->normal_termios.c_cflag; 1594 iflag = ip->normal_termios.c_iflag; 1595 me->baudrate[p] = tty_termios_baud_rate(&ip->normal_termios); 1596 } else { 1597 cflag = tty->termios.c_cflag; 1598 iflag = tty->termios.c_iflag; 1599 me->baudrate[p] = tty_get_baud_rate(tty); 1600 } 1601 tty_kref_put(tty); 1602 1603 me->databits[p] = cflag & CSIZE; 1604 me->stopbits[p] = cflag & CSTOPB; 1605 me->parity[p] = cflag & (PARENB | PARODD | 1606 CMSPAR); 1607 1608 if (cflag & CRTSCTS) 1609 me->flowctrl[p] |= 0x03; 1610 1611 if (iflag & (IXON | IXOFF)) 1612 me->flowctrl[p] |= 0x0C; 1613 1614 if (ip->type == PORT_16550A) 1615 me->fifo[p] = 1; 1616 1617 if (ip->board->chip_flag == MOXA_MUST_MU860_HWID) { 1618 opmode = inb(ip->opmode_ioaddr)>>((p % 4) * 2); 1619 opmode &= OP_MODE_MASK; 1620 } else { 1621 opmode = RS232_MODE; 1622 } 1623 me->iftype[p] = opmode; 1624 mutex_unlock(&port->mutex); 1625 } 1626 } 1627 if (copy_to_user(argp, me, sizeof(*me))) 1628 ret = -EFAULT; 1629 kfree(me); 1630 return ret; 1631 } 1632 default: 1633 return -ENOIOCTLCMD; 1634 } 1635 return 0; 1636 } 1637 1638 static int mxser_cflags_changed(struct mxser_port *info, unsigned long arg, 1639 struct async_icount *cprev) 1640 { 1641 struct async_icount cnow; 1642 unsigned long flags; 1643 int ret; 1644 1645 spin_lock_irqsave(&info->slock, flags); 1646 cnow = info->icount; /* atomic copy */ 1647 spin_unlock_irqrestore(&info->slock, flags); 1648 1649 ret = ((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) || 1650 ((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) || 1651 ((arg & TIOCM_CD) && (cnow.dcd != cprev->dcd)) || 1652 ((arg & TIOCM_CTS) && (cnow.cts != cprev->cts)); 1653 1654 *cprev = cnow; 1655 1656 return ret; 1657 } 1658 1659 static int mxser_ioctl(struct tty_struct *tty, 1660 unsigned int cmd, unsigned long arg) 1661 { 1662 struct mxser_port *info = tty->driver_data; 1663 struct tty_port *port = &info->port; 1664 struct async_icount cnow; 1665 unsigned long flags; 1666 void __user *argp = (void __user *)arg; 1667 int retval; 1668 1669 if (tty->index == MXSER_PORTS) 1670 return mxser_ioctl_special(cmd, argp); 1671 1672 if (cmd == MOXA_SET_OP_MODE || cmd == MOXA_GET_OP_MODE) { 1673 int p; 1674 unsigned long opmode; 1675 static unsigned char ModeMask[] = { 0xfc, 0xf3, 0xcf, 0x3f }; 1676 int shiftbit; 1677 unsigned char val, mask; 1678 1679 if (info->board->chip_flag != MOXA_MUST_MU860_HWID) 1680 return -EFAULT; 1681 1682 p = tty->index % 4; 1683 if (cmd == MOXA_SET_OP_MODE) { 1684 if (get_user(opmode, (int __user *) argp)) 1685 return -EFAULT; 1686 if (opmode != RS232_MODE && 1687 opmode != RS485_2WIRE_MODE && 1688 opmode != RS422_MODE && 1689 opmode != RS485_4WIRE_MODE) 1690 return -EFAULT; 1691 mask = ModeMask[p]; 1692 shiftbit = p * 2; 1693 spin_lock_irq(&info->slock); 1694 val = inb(info->opmode_ioaddr); 1695 val &= mask; 1696 val |= (opmode << shiftbit); 1697 outb(val, info->opmode_ioaddr); 1698 spin_unlock_irq(&info->slock); 1699 } else { 1700 shiftbit = p * 2; 1701 spin_lock_irq(&info->slock); 1702 opmode = inb(info->opmode_ioaddr) >> shiftbit; 1703 spin_unlock_irq(&info->slock); 1704 opmode &= OP_MODE_MASK; 1705 if (put_user(opmode, (int __user *)argp)) 1706 return -EFAULT; 1707 } 1708 return 0; 1709 } 1710 1711 if (cmd != TIOCGSERIAL && cmd != TIOCMIWAIT && tty_io_error(tty)) 1712 return -EIO; 1713 1714 switch (cmd) { 1715 case TIOCGSERIAL: 1716 mutex_lock(&port->mutex); 1717 retval = mxser_get_serial_info(tty, argp); 1718 mutex_unlock(&port->mutex); 1719 return retval; 1720 case TIOCSSERIAL: 1721 mutex_lock(&port->mutex); 1722 retval = mxser_set_serial_info(tty, argp); 1723 mutex_unlock(&port->mutex); 1724 return retval; 1725 case TIOCSERGETLSR: /* Get line status register */ 1726 return mxser_get_lsr_info(info, argp); 1727 /* 1728 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change 1729 * - mask passed in arg for lines of interest 1730 * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) 1731 * Caller should use TIOCGICOUNT to see which one it was 1732 */ 1733 case TIOCMIWAIT: 1734 spin_lock_irqsave(&info->slock, flags); 1735 cnow = info->icount; /* note the counters on entry */ 1736 spin_unlock_irqrestore(&info->slock, flags); 1737 1738 return wait_event_interruptible(info->port.delta_msr_wait, 1739 mxser_cflags_changed(info, arg, &cnow)); 1740 case MOXA_HighSpeedOn: 1741 return put_user(info->baud_base != 115200 ? 1 : 0, (int __user *)argp); 1742 case MOXA_SDS_RSTICOUNTER: 1743 spin_lock_irq(&info->slock); 1744 info->mon_data.rxcnt = 0; 1745 info->mon_data.txcnt = 0; 1746 spin_unlock_irq(&info->slock); 1747 return 0; 1748 1749 case MOXA_ASPP_OQUEUE:{ 1750 int len, lsr; 1751 1752 len = mxser_chars_in_buffer(tty); 1753 spin_lock_irq(&info->slock); 1754 lsr = inb(info->ioaddr + UART_LSR) & UART_LSR_THRE; 1755 spin_unlock_irq(&info->slock); 1756 len += (lsr ? 0 : 1); 1757 1758 return put_user(len, (int __user *)argp); 1759 } 1760 case MOXA_ASPP_MON: { 1761 int mcr, status; 1762 1763 spin_lock_irq(&info->slock); 1764 status = mxser_get_msr(info->ioaddr, 1, tty->index); 1765 mxser_check_modem_status(tty, info, status); 1766 1767 mcr = inb(info->ioaddr + UART_MCR); 1768 spin_unlock_irq(&info->slock); 1769 1770 if (mcr & MOXA_MUST_MCR_XON_FLAG) 1771 info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFHOLD; 1772 else 1773 info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFHOLD; 1774 1775 if (mcr & MOXA_MUST_MCR_TX_XON) 1776 info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFXENT; 1777 else 1778 info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFXENT; 1779 1780 if (tty->hw_stopped) 1781 info->mon_data.hold_reason |= NPPI_NOTIFY_CTSHOLD; 1782 else 1783 info->mon_data.hold_reason &= ~NPPI_NOTIFY_CTSHOLD; 1784 1785 if (copy_to_user(argp, &info->mon_data, 1786 sizeof(struct mxser_mon))) 1787 return -EFAULT; 1788 1789 return 0; 1790 } 1791 case MOXA_ASPP_LSTATUS: { 1792 if (put_user(info->err_shadow, (unsigned char __user *)argp)) 1793 return -EFAULT; 1794 1795 info->err_shadow = 0; 1796 return 0; 1797 } 1798 case MOXA_SET_BAUD_METHOD: { 1799 int method; 1800 1801 if (get_user(method, (int __user *)argp)) 1802 return -EFAULT; 1803 mxser_set_baud_method[tty->index] = method; 1804 return put_user(method, (int __user *)argp); 1805 } 1806 default: 1807 return -ENOIOCTLCMD; 1808 } 1809 return 0; 1810 } 1811 1812 /* 1813 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS) 1814 * Return: write counters to the user passed counter struct 1815 * NB: both 1->0 and 0->1 transitions are counted except for 1816 * RI where only 0->1 is counted. 1817 */ 1818 1819 static int mxser_get_icount(struct tty_struct *tty, 1820 struct serial_icounter_struct *icount) 1821 1822 { 1823 struct mxser_port *info = tty->driver_data; 1824 struct async_icount cnow; 1825 unsigned long flags; 1826 1827 spin_lock_irqsave(&info->slock, flags); 1828 cnow = info->icount; 1829 spin_unlock_irqrestore(&info->slock, flags); 1830 1831 icount->frame = cnow.frame; 1832 icount->brk = cnow.brk; 1833 icount->overrun = cnow.overrun; 1834 icount->buf_overrun = cnow.buf_overrun; 1835 icount->parity = cnow.parity; 1836 icount->rx = cnow.rx; 1837 icount->tx = cnow.tx; 1838 icount->cts = cnow.cts; 1839 icount->dsr = cnow.dsr; 1840 icount->rng = cnow.rng; 1841 icount->dcd = cnow.dcd; 1842 return 0; 1843 } 1844 1845 static void mxser_stoprx(struct tty_struct *tty) 1846 { 1847 struct mxser_port *info = tty->driver_data; 1848 1849 info->ldisc_stop_rx = 1; 1850 if (I_IXOFF(tty)) { 1851 if (info->board->chip_flag) { 1852 info->IER &= ~MOXA_MUST_RECV_ISR; 1853 outb(info->IER, info->ioaddr + UART_IER); 1854 } else { 1855 info->x_char = STOP_CHAR(tty); 1856 outb(0, info->ioaddr + UART_IER); 1857 info->IER |= UART_IER_THRI; 1858 outb(info->IER, info->ioaddr + UART_IER); 1859 } 1860 } 1861 1862 if (C_CRTSCTS(tty)) { 1863 info->MCR &= ~UART_MCR_RTS; 1864 outb(info->MCR, info->ioaddr + UART_MCR); 1865 } 1866 } 1867 1868 /* 1869 * This routine is called by the upper-layer tty layer to signal that 1870 * incoming characters should be throttled. 1871 */ 1872 static void mxser_throttle(struct tty_struct *tty) 1873 { 1874 mxser_stoprx(tty); 1875 } 1876 1877 static void mxser_unthrottle(struct tty_struct *tty) 1878 { 1879 struct mxser_port *info = tty->driver_data; 1880 1881 /* startrx */ 1882 info->ldisc_stop_rx = 0; 1883 if (I_IXOFF(tty)) { 1884 if (info->x_char) 1885 info->x_char = 0; 1886 else { 1887 if (info->board->chip_flag) { 1888 info->IER |= MOXA_MUST_RECV_ISR; 1889 outb(info->IER, info->ioaddr + UART_IER); 1890 } else { 1891 info->x_char = START_CHAR(tty); 1892 outb(0, info->ioaddr + UART_IER); 1893 info->IER |= UART_IER_THRI; 1894 outb(info->IER, info->ioaddr + UART_IER); 1895 } 1896 } 1897 } 1898 1899 if (C_CRTSCTS(tty)) { 1900 info->MCR |= UART_MCR_RTS; 1901 outb(info->MCR, info->ioaddr + UART_MCR); 1902 } 1903 } 1904 1905 /* 1906 * mxser_stop() and mxser_start() 1907 * 1908 * This routines are called before setting or resetting tty->stopped. 1909 * They enable or disable transmitter interrupts, as necessary. 1910 */ 1911 static void mxser_stop(struct tty_struct *tty) 1912 { 1913 struct mxser_port *info = tty->driver_data; 1914 unsigned long flags; 1915 1916 spin_lock_irqsave(&info->slock, flags); 1917 if (info->IER & UART_IER_THRI) { 1918 info->IER &= ~UART_IER_THRI; 1919 outb(info->IER, info->ioaddr + UART_IER); 1920 } 1921 spin_unlock_irqrestore(&info->slock, flags); 1922 } 1923 1924 static void mxser_start(struct tty_struct *tty) 1925 { 1926 struct mxser_port *info = tty->driver_data; 1927 unsigned long flags; 1928 1929 spin_lock_irqsave(&info->slock, flags); 1930 if (info->xmit_cnt && info->port.xmit_buf) { 1931 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER); 1932 info->IER |= UART_IER_THRI; 1933 outb(info->IER, info->ioaddr + UART_IER); 1934 } 1935 spin_unlock_irqrestore(&info->slock, flags); 1936 } 1937 1938 static void mxser_set_termios(struct tty_struct *tty, struct ktermios *old_termios) 1939 { 1940 struct mxser_port *info = tty->driver_data; 1941 unsigned long flags; 1942 1943 spin_lock_irqsave(&info->slock, flags); 1944 mxser_change_speed(tty, old_termios); 1945 spin_unlock_irqrestore(&info->slock, flags); 1946 1947 if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) { 1948 tty->hw_stopped = 0; 1949 mxser_start(tty); 1950 } 1951 1952 /* Handle sw stopped */ 1953 if ((old_termios->c_iflag & IXON) && !I_IXON(tty)) { 1954 tty->stopped = 0; 1955 1956 if (info->board->chip_flag) { 1957 spin_lock_irqsave(&info->slock, flags); 1958 mxser_disable_must_rx_software_flow_control( 1959 info->ioaddr); 1960 spin_unlock_irqrestore(&info->slock, flags); 1961 } 1962 1963 mxser_start(tty); 1964 } 1965 } 1966 1967 /* 1968 * mxser_wait_until_sent() --- wait until the transmitter is empty 1969 */ 1970 static void mxser_wait_until_sent(struct tty_struct *tty, int timeout) 1971 { 1972 struct mxser_port *info = tty->driver_data; 1973 unsigned long orig_jiffies, char_time; 1974 unsigned long flags; 1975 int lsr; 1976 1977 if (info->type == PORT_UNKNOWN) 1978 return; 1979 1980 if (info->xmit_fifo_size == 0) 1981 return; /* Just in case.... */ 1982 1983 orig_jiffies = jiffies; 1984 /* 1985 * Set the check interval to be 1/5 of the estimated time to 1986 * send a single character, and make it at least 1. The check 1987 * interval should also be less than the timeout. 1988 * 1989 * Note: we have to use pretty tight timings here to satisfy 1990 * the NIST-PCTS. 1991 */ 1992 char_time = (info->timeout - HZ / 50) / info->xmit_fifo_size; 1993 char_time = char_time / 5; 1994 if (char_time == 0) 1995 char_time = 1; 1996 if (timeout && timeout < char_time) 1997 char_time = timeout; 1998 /* 1999 * If the transmitter hasn't cleared in twice the approximate 2000 * amount of time to send the entire FIFO, it probably won't 2001 * ever clear. This assumes the UART isn't doing flow 2002 * control, which is currently the case. Hence, if it ever 2003 * takes longer than info->timeout, this is probably due to a 2004 * UART bug of some kind. So, we clamp the timeout parameter at 2005 * 2*info->timeout. 2006 */ 2007 if (!timeout || timeout > 2 * info->timeout) 2008 timeout = 2 * info->timeout; 2009 2010 spin_lock_irqsave(&info->slock, flags); 2011 while (!((lsr = inb(info->ioaddr + UART_LSR)) & UART_LSR_TEMT)) { 2012 spin_unlock_irqrestore(&info->slock, flags); 2013 schedule_timeout_interruptible(char_time); 2014 spin_lock_irqsave(&info->slock, flags); 2015 if (signal_pending(current)) 2016 break; 2017 if (timeout && time_after(jiffies, orig_jiffies + timeout)) 2018 break; 2019 } 2020 spin_unlock_irqrestore(&info->slock, flags); 2021 set_current_state(TASK_RUNNING); 2022 } 2023 2024 /* 2025 * This routine is called by tty_hangup() when a hangup is signaled. 2026 */ 2027 static void mxser_hangup(struct tty_struct *tty) 2028 { 2029 struct mxser_port *info = tty->driver_data; 2030 2031 mxser_flush_buffer(tty); 2032 tty_port_hangup(&info->port); 2033 } 2034 2035 /* 2036 * mxser_rs_break() --- routine which turns the break handling on or off 2037 */ 2038 static int mxser_rs_break(struct tty_struct *tty, int break_state) 2039 { 2040 struct mxser_port *info = tty->driver_data; 2041 unsigned long flags; 2042 2043 spin_lock_irqsave(&info->slock, flags); 2044 if (break_state == -1) 2045 outb(inb(info->ioaddr + UART_LCR) | UART_LCR_SBC, 2046 info->ioaddr + UART_LCR); 2047 else 2048 outb(inb(info->ioaddr + UART_LCR) & ~UART_LCR_SBC, 2049 info->ioaddr + UART_LCR); 2050 spin_unlock_irqrestore(&info->slock, flags); 2051 return 0; 2052 } 2053 2054 static void mxser_receive_chars(struct tty_struct *tty, 2055 struct mxser_port *port, int *status) 2056 { 2057 unsigned char ch, gdl; 2058 int ignored = 0; 2059 int cnt = 0; 2060 int recv_room; 2061 int max = 256; 2062 2063 recv_room = tty->receive_room; 2064 if (recv_room == 0 && !port->ldisc_stop_rx) 2065 mxser_stoprx(tty); 2066 if (port->board->chip_flag != MOXA_OTHER_UART) { 2067 2068 if (*status & UART_LSR_SPECIAL) 2069 goto intr_old; 2070 if (port->board->chip_flag == MOXA_MUST_MU860_HWID && 2071 (*status & MOXA_MUST_LSR_RERR)) 2072 goto intr_old; 2073 if (*status & MOXA_MUST_LSR_RERR) 2074 goto intr_old; 2075 2076 gdl = inb(port->ioaddr + MOXA_MUST_GDL_REGISTER); 2077 2078 if (port->board->chip_flag == MOXA_MUST_MU150_HWID) 2079 gdl &= MOXA_MUST_GDL_MASK; 2080 if (gdl >= recv_room) { 2081 if (!port->ldisc_stop_rx) 2082 mxser_stoprx(tty); 2083 } 2084 while (gdl--) { 2085 ch = inb(port->ioaddr + UART_RX); 2086 tty_insert_flip_char(&port->port, ch, 0); 2087 cnt++; 2088 } 2089 goto end_intr; 2090 } 2091 intr_old: 2092 2093 do { 2094 if (max-- < 0) 2095 break; 2096 2097 ch = inb(port->ioaddr + UART_RX); 2098 if (port->board->chip_flag && (*status & UART_LSR_OE)) 2099 outb(0x23, port->ioaddr + UART_FCR); 2100 *status &= port->read_status_mask; 2101 if (*status & port->ignore_status_mask) { 2102 if (++ignored > 100) 2103 break; 2104 } else { 2105 char flag = 0; 2106 if (*status & UART_LSR_SPECIAL) { 2107 if (*status & UART_LSR_BI) { 2108 flag = TTY_BREAK; 2109 port->icount.brk++; 2110 2111 if (port->port.flags & ASYNC_SAK) 2112 do_SAK(tty); 2113 } else if (*status & UART_LSR_PE) { 2114 flag = TTY_PARITY; 2115 port->icount.parity++; 2116 } else if (*status & UART_LSR_FE) { 2117 flag = TTY_FRAME; 2118 port->icount.frame++; 2119 } else if (*status & UART_LSR_OE) { 2120 flag = TTY_OVERRUN; 2121 port->icount.overrun++; 2122 } else 2123 flag = TTY_BREAK; 2124 } 2125 tty_insert_flip_char(&port->port, ch, flag); 2126 cnt++; 2127 if (cnt >= recv_room) { 2128 if (!port->ldisc_stop_rx) 2129 mxser_stoprx(tty); 2130 break; 2131 } 2132 2133 } 2134 2135 if (port->board->chip_flag) 2136 break; 2137 2138 *status = inb(port->ioaddr + UART_LSR); 2139 } while (*status & UART_LSR_DR); 2140 2141 end_intr: 2142 mxvar_log.rxcnt[tty->index] += cnt; 2143 port->mon_data.rxcnt += cnt; 2144 port->mon_data.up_rxcnt += cnt; 2145 2146 /* 2147 * We are called from an interrupt context with &port->slock 2148 * being held. Drop it temporarily in order to prevent 2149 * recursive locking. 2150 */ 2151 spin_unlock(&port->slock); 2152 tty_flip_buffer_push(&port->port); 2153 spin_lock(&port->slock); 2154 } 2155 2156 static void mxser_transmit_chars(struct tty_struct *tty, struct mxser_port *port) 2157 { 2158 int count, cnt; 2159 2160 if (port->x_char) { 2161 outb(port->x_char, port->ioaddr + UART_TX); 2162 port->x_char = 0; 2163 mxvar_log.txcnt[tty->index]++; 2164 port->mon_data.txcnt++; 2165 port->mon_data.up_txcnt++; 2166 port->icount.tx++; 2167 return; 2168 } 2169 2170 if (port->port.xmit_buf == NULL) 2171 return; 2172 2173 if (port->xmit_cnt <= 0 || tty->stopped || 2174 (tty->hw_stopped && 2175 (port->type != PORT_16550A) && 2176 (!port->board->chip_flag))) { 2177 port->IER &= ~UART_IER_THRI; 2178 outb(port->IER, port->ioaddr + UART_IER); 2179 return; 2180 } 2181 2182 cnt = port->xmit_cnt; 2183 count = port->xmit_fifo_size; 2184 do { 2185 outb(port->port.xmit_buf[port->xmit_tail++], 2186 port->ioaddr + UART_TX); 2187 port->xmit_tail = port->xmit_tail & (SERIAL_XMIT_SIZE - 1); 2188 if (--port->xmit_cnt <= 0) 2189 break; 2190 } while (--count > 0); 2191 mxvar_log.txcnt[tty->index] += (cnt - port->xmit_cnt); 2192 2193 port->mon_data.txcnt += (cnt - port->xmit_cnt); 2194 port->mon_data.up_txcnt += (cnt - port->xmit_cnt); 2195 port->icount.tx += (cnt - port->xmit_cnt); 2196 2197 if (port->xmit_cnt < WAKEUP_CHARS) 2198 tty_wakeup(tty); 2199 2200 if (port->xmit_cnt <= 0) { 2201 port->IER &= ~UART_IER_THRI; 2202 outb(port->IER, port->ioaddr + UART_IER); 2203 } 2204 } 2205 2206 /* 2207 * This is the serial driver's generic interrupt routine 2208 */ 2209 static irqreturn_t mxser_interrupt(int irq, void *dev_id) 2210 { 2211 int status, iir, i; 2212 struct mxser_board *brd = NULL; 2213 struct mxser_port *port; 2214 int max, irqbits, bits, msr; 2215 unsigned int int_cnt, pass_counter = 0; 2216 int handled = IRQ_NONE; 2217 struct tty_struct *tty; 2218 2219 for (i = 0; i < MXSER_BOARDS; i++) 2220 if (dev_id == &mxser_boards[i]) { 2221 brd = dev_id; 2222 break; 2223 } 2224 2225 if (i == MXSER_BOARDS) 2226 goto irq_stop; 2227 if (brd == NULL) 2228 goto irq_stop; 2229 max = brd->info->nports; 2230 while (pass_counter++ < MXSER_ISR_PASS_LIMIT) { 2231 irqbits = inb(brd->vector) & brd->vector_mask; 2232 if (irqbits == brd->vector_mask) 2233 break; 2234 2235 handled = IRQ_HANDLED; 2236 for (i = 0, bits = 1; i < max; i++, irqbits |= bits, bits <<= 1) { 2237 if (irqbits == brd->vector_mask) 2238 break; 2239 if (bits & irqbits) 2240 continue; 2241 port = &brd->ports[i]; 2242 2243 int_cnt = 0; 2244 spin_lock(&port->slock); 2245 do { 2246 iir = inb(port->ioaddr + UART_IIR); 2247 if (iir & UART_IIR_NO_INT) 2248 break; 2249 iir &= MOXA_MUST_IIR_MASK; 2250 tty = tty_port_tty_get(&port->port); 2251 if (!tty || port->closing || 2252 !tty_port_initialized(&port->port)) { 2253 status = inb(port->ioaddr + UART_LSR); 2254 outb(0x27, port->ioaddr + UART_FCR); 2255 inb(port->ioaddr + UART_MSR); 2256 tty_kref_put(tty); 2257 break; 2258 } 2259 2260 status = inb(port->ioaddr + UART_LSR); 2261 2262 if (status & UART_LSR_PE) 2263 port->err_shadow |= NPPI_NOTIFY_PARITY; 2264 if (status & UART_LSR_FE) 2265 port->err_shadow |= NPPI_NOTIFY_FRAMING; 2266 if (status & UART_LSR_OE) 2267 port->err_shadow |= 2268 NPPI_NOTIFY_HW_OVERRUN; 2269 if (status & UART_LSR_BI) 2270 port->err_shadow |= NPPI_NOTIFY_BREAK; 2271 2272 if (port->board->chip_flag) { 2273 if (iir == MOXA_MUST_IIR_GDA || 2274 iir == MOXA_MUST_IIR_RDA || 2275 iir == MOXA_MUST_IIR_RTO || 2276 iir == MOXA_MUST_IIR_LSR) 2277 mxser_receive_chars(tty, port, 2278 &status); 2279 2280 } else { 2281 status &= port->read_status_mask; 2282 if (status & UART_LSR_DR) 2283 mxser_receive_chars(tty, port, 2284 &status); 2285 } 2286 msr = inb(port->ioaddr + UART_MSR); 2287 if (msr & UART_MSR_ANY_DELTA) 2288 mxser_check_modem_status(tty, port, msr); 2289 2290 if (port->board->chip_flag) { 2291 if (iir == 0x02 && (status & 2292 UART_LSR_THRE)) 2293 mxser_transmit_chars(tty, port); 2294 } else { 2295 if (status & UART_LSR_THRE) 2296 mxser_transmit_chars(tty, port); 2297 } 2298 tty_kref_put(tty); 2299 } while (int_cnt++ < MXSER_ISR_PASS_LIMIT); 2300 spin_unlock(&port->slock); 2301 } 2302 } 2303 2304 irq_stop: 2305 return handled; 2306 } 2307 2308 static const struct tty_operations mxser_ops = { 2309 .open = mxser_open, 2310 .close = mxser_close, 2311 .write = mxser_write, 2312 .put_char = mxser_put_char, 2313 .flush_chars = mxser_flush_chars, 2314 .write_room = mxser_write_room, 2315 .chars_in_buffer = mxser_chars_in_buffer, 2316 .flush_buffer = mxser_flush_buffer, 2317 .ioctl = mxser_ioctl, 2318 .throttle = mxser_throttle, 2319 .unthrottle = mxser_unthrottle, 2320 .set_termios = mxser_set_termios, 2321 .stop = mxser_stop, 2322 .start = mxser_start, 2323 .hangup = mxser_hangup, 2324 .break_ctl = mxser_rs_break, 2325 .wait_until_sent = mxser_wait_until_sent, 2326 .tiocmget = mxser_tiocmget, 2327 .tiocmset = mxser_tiocmset, 2328 .get_icount = mxser_get_icount, 2329 }; 2330 2331 static const struct tty_port_operations mxser_port_ops = { 2332 .carrier_raised = mxser_carrier_raised, 2333 .dtr_rts = mxser_dtr_rts, 2334 .activate = mxser_activate, 2335 .shutdown = mxser_shutdown_port, 2336 }; 2337 2338 /* 2339 * The MOXA Smartio/Industio serial driver boot-time initialization code! 2340 */ 2341 2342 static bool allow_overlapping_vector; 2343 module_param(allow_overlapping_vector, bool, S_IRUGO); 2344 MODULE_PARM_DESC(allow_overlapping_vector, "whether we allow ISA cards to be configured such that vector overlabs IO ports (default=no)"); 2345 2346 static bool mxser_overlapping_vector(struct mxser_board *brd) 2347 { 2348 return allow_overlapping_vector && 2349 brd->vector >= brd->ports[0].ioaddr && 2350 brd->vector < brd->ports[0].ioaddr + 8 * brd->info->nports; 2351 } 2352 2353 static int mxser_request_vector(struct mxser_board *brd) 2354 { 2355 if (mxser_overlapping_vector(brd)) 2356 return 0; 2357 return request_region(brd->vector, 1, "mxser(vector)") ? 0 : -EIO; 2358 } 2359 2360 static void mxser_release_vector(struct mxser_board *brd) 2361 { 2362 if (mxser_overlapping_vector(brd)) 2363 return; 2364 release_region(brd->vector, 1); 2365 } 2366 2367 static void mxser_release_ISA_res(struct mxser_board *brd) 2368 { 2369 release_region(brd->ports[0].ioaddr, 8 * brd->info->nports); 2370 mxser_release_vector(brd); 2371 } 2372 2373 static int mxser_initbrd(struct mxser_board *brd, 2374 struct pci_dev *pdev) 2375 { 2376 struct mxser_port *info; 2377 unsigned int i; 2378 int retval; 2379 2380 printk(KERN_INFO "mxser: max. baud rate = %d bps\n", 2381 brd->ports[0].max_baud); 2382 2383 for (i = 0; i < brd->info->nports; i++) { 2384 info = &brd->ports[i]; 2385 tty_port_init(&info->port); 2386 info->port.ops = &mxser_port_ops; 2387 info->board = brd; 2388 info->stop_rx = 0; 2389 info->ldisc_stop_rx = 0; 2390 2391 /* Enhance mode enabled here */ 2392 if (brd->chip_flag != MOXA_OTHER_UART) 2393 mxser_enable_must_enchance_mode(info->ioaddr); 2394 2395 info->type = brd->uart_type; 2396 2397 process_txrx_fifo(info); 2398 2399 info->custom_divisor = info->baud_base * 16; 2400 info->port.close_delay = 5 * HZ / 10; 2401 info->port.closing_wait = 30 * HZ; 2402 info->normal_termios = mxvar_sdriver->init_termios; 2403 memset(&info->mon_data, 0, sizeof(struct mxser_mon)); 2404 info->err_shadow = 0; 2405 spin_lock_init(&info->slock); 2406 2407 /* before set INT ISR, disable all int */ 2408 outb(inb(info->ioaddr + UART_IER) & 0xf0, 2409 info->ioaddr + UART_IER); 2410 } 2411 2412 retval = request_irq(brd->irq, mxser_interrupt, IRQF_SHARED, "mxser", 2413 brd); 2414 if (retval) { 2415 for (i = 0; i < brd->info->nports; i++) 2416 tty_port_destroy(&brd->ports[i].port); 2417 printk(KERN_ERR "Board %s: Request irq failed, IRQ (%d) may " 2418 "conflict with another device.\n", 2419 brd->info->name, brd->irq); 2420 } 2421 2422 return retval; 2423 } 2424 2425 static void mxser_board_remove(struct mxser_board *brd) 2426 { 2427 unsigned int i; 2428 2429 for (i = 0; i < brd->info->nports; i++) { 2430 tty_unregister_device(mxvar_sdriver, brd->idx + i); 2431 tty_port_destroy(&brd->ports[i].port); 2432 } 2433 free_irq(brd->irq, brd); 2434 } 2435 2436 static int __init mxser_get_ISA_conf(int cap, struct mxser_board *brd) 2437 { 2438 int id, i, bits, ret; 2439 unsigned short regs[16], irq; 2440 unsigned char scratch, scratch2; 2441 2442 brd->chip_flag = MOXA_OTHER_UART; 2443 2444 id = mxser_read_register(cap, regs); 2445 switch (id) { 2446 case C168_ASIC_ID: 2447 brd->info = &mxser_cards[0]; 2448 break; 2449 case C104_ASIC_ID: 2450 brd->info = &mxser_cards[1]; 2451 break; 2452 case CI104J_ASIC_ID: 2453 brd->info = &mxser_cards[2]; 2454 break; 2455 case C102_ASIC_ID: 2456 brd->info = &mxser_cards[5]; 2457 break; 2458 case CI132_ASIC_ID: 2459 brd->info = &mxser_cards[6]; 2460 break; 2461 case CI134_ASIC_ID: 2462 brd->info = &mxser_cards[7]; 2463 break; 2464 default: 2465 return 0; 2466 } 2467 2468 irq = 0; 2469 /* some ISA cards have 2 ports, but we want to see them as 4-port (why?) 2470 Flag-hack checks if configuration should be read as 2-port here. */ 2471 if (brd->info->nports == 2 || (brd->info->flags & MXSER_HAS2)) { 2472 irq = regs[9] & 0xF000; 2473 irq = irq | (irq >> 4); 2474 if (irq != (regs[9] & 0xFF00)) 2475 goto err_irqconflict; 2476 } else if (brd->info->nports == 4) { 2477 irq = regs[9] & 0xF000; 2478 irq = irq | (irq >> 4); 2479 irq = irq | (irq >> 8); 2480 if (irq != regs[9]) 2481 goto err_irqconflict; 2482 } else if (brd->info->nports == 8) { 2483 irq = regs[9] & 0xF000; 2484 irq = irq | (irq >> 4); 2485 irq = irq | (irq >> 8); 2486 if ((irq != regs[9]) || (irq != regs[10])) 2487 goto err_irqconflict; 2488 } 2489 2490 if (!irq) { 2491 printk(KERN_ERR "mxser: interrupt number unset\n"); 2492 return -EIO; 2493 } 2494 brd->irq = ((int)(irq & 0xF000) >> 12); 2495 for (i = 0; i < 8; i++) 2496 brd->ports[i].ioaddr = (int) regs[i + 1] & 0xFFF8; 2497 if ((regs[12] & 0x80) == 0) { 2498 printk(KERN_ERR "mxser: invalid interrupt vector\n"); 2499 return -EIO; 2500 } 2501 brd->vector = (int)regs[11]; /* interrupt vector */ 2502 if (id == 1) 2503 brd->vector_mask = 0x00FF; 2504 else 2505 brd->vector_mask = 0x000F; 2506 for (i = 7, bits = 0x0100; i >= 0; i--, bits <<= 1) { 2507 if (regs[12] & bits) { 2508 brd->ports[i].baud_base = 921600; 2509 brd->ports[i].max_baud = 921600; 2510 } else { 2511 brd->ports[i].baud_base = 115200; 2512 brd->ports[i].max_baud = 115200; 2513 } 2514 } 2515 scratch2 = inb(cap + UART_LCR) & (~UART_LCR_DLAB); 2516 outb(scratch2 | UART_LCR_DLAB, cap + UART_LCR); 2517 outb(0, cap + UART_EFR); /* EFR is the same as FCR */ 2518 outb(scratch2, cap + UART_LCR); 2519 outb(UART_FCR_ENABLE_FIFO, cap + UART_FCR); 2520 scratch = inb(cap + UART_IIR); 2521 2522 if (scratch & 0xC0) 2523 brd->uart_type = PORT_16550A; 2524 else 2525 brd->uart_type = PORT_16450; 2526 if (!request_region(brd->ports[0].ioaddr, 8 * brd->info->nports, 2527 "mxser(IO)")) { 2528 printk(KERN_ERR "mxser: can't request ports I/O region: " 2529 "0x%.8lx-0x%.8lx\n", 2530 brd->ports[0].ioaddr, brd->ports[0].ioaddr + 2531 8 * brd->info->nports - 1); 2532 return -EIO; 2533 } 2534 2535 ret = mxser_request_vector(brd); 2536 if (ret) { 2537 release_region(brd->ports[0].ioaddr, 8 * brd->info->nports); 2538 printk(KERN_ERR "mxser: can't request interrupt vector region: " 2539 "0x%.8lx-0x%.8lx\n", 2540 brd->ports[0].ioaddr, brd->ports[0].ioaddr + 2541 8 * brd->info->nports - 1); 2542 return ret; 2543 } 2544 return brd->info->nports; 2545 2546 err_irqconflict: 2547 printk(KERN_ERR "mxser: invalid interrupt number\n"); 2548 return -EIO; 2549 } 2550 2551 static int mxser_probe(struct pci_dev *pdev, 2552 const struct pci_device_id *ent) 2553 { 2554 #ifdef CONFIG_PCI 2555 struct mxser_board *brd; 2556 unsigned int i, j; 2557 unsigned long ioaddress; 2558 struct device *tty_dev; 2559 int retval = -EINVAL; 2560 2561 for (i = 0; i < MXSER_BOARDS; i++) 2562 if (mxser_boards[i].info == NULL) 2563 break; 2564 2565 if (i >= MXSER_BOARDS) { 2566 dev_err(&pdev->dev, "too many boards found (maximum %d), board " 2567 "not configured\n", MXSER_BOARDS); 2568 goto err; 2569 } 2570 2571 brd = &mxser_boards[i]; 2572 brd->idx = i * MXSER_PORTS_PER_BOARD; 2573 dev_info(&pdev->dev, "found MOXA %s board (BusNo=%d, DevNo=%d)\n", 2574 mxser_cards[ent->driver_data].name, 2575 pdev->bus->number, PCI_SLOT(pdev->devfn)); 2576 2577 retval = pci_enable_device(pdev); 2578 if (retval) { 2579 dev_err(&pdev->dev, "PCI enable failed\n"); 2580 goto err; 2581 } 2582 2583 /* io address */ 2584 ioaddress = pci_resource_start(pdev, 2); 2585 retval = pci_request_region(pdev, 2, "mxser(IO)"); 2586 if (retval) 2587 goto err_dis; 2588 2589 brd->info = &mxser_cards[ent->driver_data]; 2590 for (i = 0; i < brd->info->nports; i++) 2591 brd->ports[i].ioaddr = ioaddress + 8 * i; 2592 2593 /* vector */ 2594 ioaddress = pci_resource_start(pdev, 3); 2595 retval = pci_request_region(pdev, 3, "mxser(vector)"); 2596 if (retval) 2597 goto err_zero; 2598 brd->vector = ioaddress; 2599 2600 /* irq */ 2601 brd->irq = pdev->irq; 2602 2603 brd->chip_flag = CheckIsMoxaMust(brd->ports[0].ioaddr); 2604 brd->uart_type = PORT_16550A; 2605 brd->vector_mask = 0; 2606 2607 for (i = 0; i < brd->info->nports; i++) { 2608 for (j = 0; j < UART_INFO_NUM; j++) { 2609 if (Gpci_uart_info[j].type == brd->chip_flag) { 2610 brd->ports[i].max_baud = 2611 Gpci_uart_info[j].max_baud; 2612 2613 /* exception....CP-102 */ 2614 if (brd->info->flags & MXSER_HIGHBAUD) 2615 brd->ports[i].max_baud = 921600; 2616 break; 2617 } 2618 } 2619 } 2620 2621 if (brd->chip_flag == MOXA_MUST_MU860_HWID) { 2622 for (i = 0; i < brd->info->nports; i++) { 2623 if (i < 4) 2624 brd->ports[i].opmode_ioaddr = ioaddress + 4; 2625 else 2626 brd->ports[i].opmode_ioaddr = ioaddress + 0x0c; 2627 } 2628 outb(0, ioaddress + 4); /* default set to RS232 mode */ 2629 outb(0, ioaddress + 0x0c); /* default set to RS232 mode */ 2630 } 2631 2632 for (i = 0; i < brd->info->nports; i++) { 2633 brd->vector_mask |= (1 << i); 2634 brd->ports[i].baud_base = 921600; 2635 } 2636 2637 /* mxser_initbrd will hook ISR. */ 2638 retval = mxser_initbrd(brd, pdev); 2639 if (retval) 2640 goto err_rel3; 2641 2642 for (i = 0; i < brd->info->nports; i++) { 2643 tty_dev = tty_port_register_device(&brd->ports[i].port, 2644 mxvar_sdriver, brd->idx + i, &pdev->dev); 2645 if (IS_ERR(tty_dev)) { 2646 retval = PTR_ERR(tty_dev); 2647 for (; i > 0; i--) 2648 tty_unregister_device(mxvar_sdriver, 2649 brd->idx + i - 1); 2650 goto err_relbrd; 2651 } 2652 } 2653 2654 pci_set_drvdata(pdev, brd); 2655 2656 return 0; 2657 err_relbrd: 2658 for (i = 0; i < brd->info->nports; i++) 2659 tty_port_destroy(&brd->ports[i].port); 2660 free_irq(brd->irq, brd); 2661 err_rel3: 2662 pci_release_region(pdev, 3); 2663 err_zero: 2664 brd->info = NULL; 2665 pci_release_region(pdev, 2); 2666 err_dis: 2667 pci_disable_device(pdev); 2668 err: 2669 return retval; 2670 #else 2671 return -ENODEV; 2672 #endif 2673 } 2674 2675 static void mxser_remove(struct pci_dev *pdev) 2676 { 2677 #ifdef CONFIG_PCI 2678 struct mxser_board *brd = pci_get_drvdata(pdev); 2679 2680 mxser_board_remove(brd); 2681 2682 pci_release_region(pdev, 2); 2683 pci_release_region(pdev, 3); 2684 pci_disable_device(pdev); 2685 brd->info = NULL; 2686 #endif 2687 } 2688 2689 static struct pci_driver mxser_driver = { 2690 .name = "mxser", 2691 .id_table = mxser_pcibrds, 2692 .probe = mxser_probe, 2693 .remove = mxser_remove 2694 }; 2695 2696 static int __init mxser_module_init(void) 2697 { 2698 struct mxser_board *brd; 2699 struct device *tty_dev; 2700 unsigned int b, i, m; 2701 int retval; 2702 2703 mxvar_sdriver = alloc_tty_driver(MXSER_PORTS + 1); 2704 if (!mxvar_sdriver) 2705 return -ENOMEM; 2706 2707 printk(KERN_INFO "MOXA Smartio/Industio family driver version %s\n", 2708 MXSER_VERSION); 2709 2710 /* Initialize the tty_driver structure */ 2711 mxvar_sdriver->name = "ttyMI"; 2712 mxvar_sdriver->major = ttymajor; 2713 mxvar_sdriver->minor_start = 0; 2714 mxvar_sdriver->type = TTY_DRIVER_TYPE_SERIAL; 2715 mxvar_sdriver->subtype = SERIAL_TYPE_NORMAL; 2716 mxvar_sdriver->init_termios = tty_std_termios; 2717 mxvar_sdriver->init_termios.c_cflag = B9600|CS8|CREAD|HUPCL|CLOCAL; 2718 mxvar_sdriver->flags = TTY_DRIVER_REAL_RAW|TTY_DRIVER_DYNAMIC_DEV; 2719 tty_set_operations(mxvar_sdriver, &mxser_ops); 2720 2721 retval = tty_register_driver(mxvar_sdriver); 2722 if (retval) { 2723 printk(KERN_ERR "Couldn't install MOXA Smartio/Industio family " 2724 "tty driver !\n"); 2725 goto err_put; 2726 } 2727 2728 /* Start finding ISA boards here */ 2729 for (m = 0, b = 0; b < MXSER_BOARDS; b++) { 2730 if (!ioaddr[b]) 2731 continue; 2732 2733 brd = &mxser_boards[m]; 2734 retval = mxser_get_ISA_conf(ioaddr[b], brd); 2735 if (retval <= 0) { 2736 brd->info = NULL; 2737 continue; 2738 } 2739 2740 printk(KERN_INFO "mxser: found MOXA %s board (CAP=0x%lx)\n", 2741 brd->info->name, ioaddr[b]); 2742 2743 /* mxser_initbrd will hook ISR. */ 2744 if (mxser_initbrd(brd, NULL) < 0) { 2745 mxser_release_ISA_res(brd); 2746 brd->info = NULL; 2747 continue; 2748 } 2749 2750 brd->idx = m * MXSER_PORTS_PER_BOARD; 2751 for (i = 0; i < brd->info->nports; i++) { 2752 tty_dev = tty_port_register_device(&brd->ports[i].port, 2753 mxvar_sdriver, brd->idx + i, NULL); 2754 if (IS_ERR(tty_dev)) { 2755 for (; i > 0; i--) 2756 tty_unregister_device(mxvar_sdriver, 2757 brd->idx + i - 1); 2758 for (i = 0; i < brd->info->nports; i++) 2759 tty_port_destroy(&brd->ports[i].port); 2760 free_irq(brd->irq, brd); 2761 mxser_release_ISA_res(brd); 2762 brd->info = NULL; 2763 break; 2764 } 2765 } 2766 if (brd->info == NULL) 2767 continue; 2768 2769 m++; 2770 } 2771 2772 retval = pci_register_driver(&mxser_driver); 2773 if (retval) { 2774 printk(KERN_ERR "mxser: can't register pci driver\n"); 2775 if (!m) { 2776 retval = -ENODEV; 2777 goto err_unr; 2778 } /* else: we have some ISA cards under control */ 2779 } 2780 2781 return 0; 2782 err_unr: 2783 tty_unregister_driver(mxvar_sdriver); 2784 err_put: 2785 put_tty_driver(mxvar_sdriver); 2786 return retval; 2787 } 2788 2789 static void __exit mxser_module_exit(void) 2790 { 2791 unsigned int i; 2792 2793 pci_unregister_driver(&mxser_driver); 2794 2795 for (i = 0; i < MXSER_BOARDS; i++) /* ISA remains */ 2796 if (mxser_boards[i].info != NULL) 2797 mxser_board_remove(&mxser_boards[i]); 2798 tty_unregister_driver(mxvar_sdriver); 2799 put_tty_driver(mxvar_sdriver); 2800 2801 for (i = 0; i < MXSER_BOARDS; i++) 2802 if (mxser_boards[i].info != NULL) 2803 mxser_release_ISA_res(&mxser_boards[i]); 2804 } 2805 2806 module_init(mxser_module_init); 2807 module_exit(mxser_module_exit); 2808