1 /* 2 * Serial driver for the amiga builtin port. 3 * 4 * This code was created by taking serial.c version 4.30 from kernel 5 * release 2.3.22, replacing all hardware related stuff with the 6 * corresponding amiga hardware actions, and removing all irrelevant 7 * code. As a consequence, it uses many of the constants and names 8 * associated with the registers and bits of 16550 compatible UARTS - 9 * but only to keep track of status, etc in the state variables. It 10 * was done this was to make it easier to keep the code in line with 11 * (non hardware specific) changes to serial.c. 12 * 13 * The port is registered with the tty driver as minor device 64, and 14 * therefore other ports should should only use 65 upwards. 15 * 16 * Richard Lucock 28/12/99 17 * 18 * Copyright (C) 1991, 1992 Linus Torvalds 19 * Copyright (C) 1992, 1993, 1994, 1995, 1996, 1997, 20 * 1998, 1999 Theodore Ts'o 21 * 22 */ 23 24 /* 25 * Serial driver configuration section. Here are the various options: 26 * 27 * SERIAL_PARANOIA_CHECK 28 * Check the magic number for the async_structure where 29 * ever possible. 30 */ 31 32 #include <linux/delay.h> 33 34 #undef SERIAL_PARANOIA_CHECK 35 #define SERIAL_DO_RESTART 36 37 /* Set of debugging defines */ 38 39 #undef SERIAL_DEBUG_INTR 40 #undef SERIAL_DEBUG_OPEN 41 #undef SERIAL_DEBUG_FLOW 42 #undef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT 43 44 /* Sanity checks */ 45 46 #if defined(MODULE) && defined(SERIAL_DEBUG_MCOUNT) 47 #define DBG_CNT(s) printk("(%s): [%x] refc=%d, serc=%d, ttyc=%d -> %s\n", \ 48 tty->name, (info->tport.flags), serial_driver->refcount,info->count,tty->count,s) 49 #else 50 #define DBG_CNT(s) 51 #endif 52 53 /* 54 * End of serial driver configuration section. 55 */ 56 57 #include <linux/module.h> 58 59 #include <linux/types.h> 60 #include <linux/serial.h> 61 #include <linux/serial_reg.h> 62 static char *serial_version = "4.30"; 63 64 #include <linux/errno.h> 65 #include <linux/signal.h> 66 #include <linux/sched.h> 67 #include <linux/kernel.h> 68 #include <linux/timer.h> 69 #include <linux/interrupt.h> 70 #include <linux/tty.h> 71 #include <linux/tty_flip.h> 72 #include <linux/circ_buf.h> 73 #include <linux/console.h> 74 #include <linux/major.h> 75 #include <linux/string.h> 76 #include <linux/fcntl.h> 77 #include <linux/ptrace.h> 78 #include <linux/ioport.h> 79 #include <linux/mm.h> 80 #include <linux/seq_file.h> 81 #include <linux/slab.h> 82 #include <linux/init.h> 83 #include <linux/bitops.h> 84 #include <linux/platform_device.h> 85 86 #include <asm/setup.h> 87 88 89 #include <asm/irq.h> 90 91 #include <asm/amigahw.h> 92 #include <asm/amigaints.h> 93 94 struct serial_state { 95 struct tty_port tport; 96 struct circ_buf xmit; 97 struct async_icount icount; 98 99 unsigned long port; 100 int baud_base; 101 int xmit_fifo_size; 102 int custom_divisor; 103 int read_status_mask; 104 int ignore_status_mask; 105 int timeout; 106 int quot; 107 int IER; /* Interrupt Enable Register */ 108 int MCR; /* Modem control register */ 109 int x_char; /* xon/xoff character */ 110 }; 111 112 #define custom amiga_custom 113 static char *serial_name = "Amiga-builtin serial driver"; 114 115 static struct tty_driver *serial_driver; 116 117 /* number of characters left in xmit buffer before we ask for more */ 118 #define WAKEUP_CHARS 256 119 120 static unsigned char current_ctl_bits; 121 122 static void change_speed(struct tty_struct *tty, struct serial_state *info, 123 struct ktermios *old); 124 static void rs_wait_until_sent(struct tty_struct *tty, int timeout); 125 126 127 static struct serial_state rs_table[1]; 128 129 #define NR_PORTS ARRAY_SIZE(rs_table) 130 131 #include <asm/uaccess.h> 132 133 #define serial_isroot() (capable(CAP_SYS_ADMIN)) 134 135 136 static inline int serial_paranoia_check(struct serial_state *info, 137 char *name, const char *routine) 138 { 139 #ifdef SERIAL_PARANOIA_CHECK 140 static const char *badmagic = 141 "Warning: bad magic number for serial struct (%s) in %s\n"; 142 static const char *badinfo = 143 "Warning: null async_struct for (%s) in %s\n"; 144 145 if (!info) { 146 printk(badinfo, name, routine); 147 return 1; 148 } 149 if (info->magic != SERIAL_MAGIC) { 150 printk(badmagic, name, routine); 151 return 1; 152 } 153 #endif 154 return 0; 155 } 156 157 /* some serial hardware definitions */ 158 #define SDR_OVRUN (1<<15) 159 #define SDR_RBF (1<<14) 160 #define SDR_TBE (1<<13) 161 #define SDR_TSRE (1<<12) 162 163 #define SERPER_PARENB (1<<15) 164 165 #define AC_SETCLR (1<<15) 166 #define AC_UARTBRK (1<<11) 167 168 #define SER_DTR (1<<7) 169 #define SER_RTS (1<<6) 170 #define SER_DCD (1<<5) 171 #define SER_CTS (1<<4) 172 #define SER_DSR (1<<3) 173 174 static __inline__ void rtsdtr_ctrl(int bits) 175 { 176 ciab.pra = ((bits & (SER_RTS | SER_DTR)) ^ (SER_RTS | SER_DTR)) | (ciab.pra & ~(SER_RTS | SER_DTR)); 177 } 178 179 /* 180 * ------------------------------------------------------------ 181 * rs_stop() and rs_start() 182 * 183 * This routines are called before setting or resetting tty->stopped. 184 * They enable or disable transmitter interrupts, as necessary. 185 * ------------------------------------------------------------ 186 */ 187 static void rs_stop(struct tty_struct *tty) 188 { 189 struct serial_state *info = tty->driver_data; 190 unsigned long flags; 191 192 if (serial_paranoia_check(info, tty->name, "rs_stop")) 193 return; 194 195 local_irq_save(flags); 196 if (info->IER & UART_IER_THRI) { 197 info->IER &= ~UART_IER_THRI; 198 /* disable Tx interrupt and remove any pending interrupts */ 199 custom.intena = IF_TBE; 200 mb(); 201 custom.intreq = IF_TBE; 202 mb(); 203 } 204 local_irq_restore(flags); 205 } 206 207 static void rs_start(struct tty_struct *tty) 208 { 209 struct serial_state *info = tty->driver_data; 210 unsigned long flags; 211 212 if (serial_paranoia_check(info, tty->name, "rs_start")) 213 return; 214 215 local_irq_save(flags); 216 if (info->xmit.head != info->xmit.tail 217 && info->xmit.buf 218 && !(info->IER & UART_IER_THRI)) { 219 info->IER |= UART_IER_THRI; 220 custom.intena = IF_SETCLR | IF_TBE; 221 mb(); 222 /* set a pending Tx Interrupt, transmitter should restart now */ 223 custom.intreq = IF_SETCLR | IF_TBE; 224 mb(); 225 } 226 local_irq_restore(flags); 227 } 228 229 /* 230 * ---------------------------------------------------------------------- 231 * 232 * Here starts the interrupt handling routines. All of the following 233 * subroutines are declared as inline and are folded into 234 * rs_interrupt(). They were separated out for readability's sake. 235 * 236 * Note: rs_interrupt() is a "fast" interrupt, which means that it 237 * runs with interrupts turned off. People who may want to modify 238 * rs_interrupt() should try to keep the interrupt handler as fast as 239 * possible. After you are done making modifications, it is not a bad 240 * idea to do: 241 * 242 * gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c 243 * 244 * and look at the resulting assemble code in serial.s. 245 * 246 * - Ted Ts'o (tytso@mit.edu), 7-Mar-93 247 * ----------------------------------------------------------------------- 248 */ 249 250 static void receive_chars(struct serial_state *info) 251 { 252 int status; 253 int serdatr; 254 unsigned char ch, flag; 255 struct async_icount *icount; 256 int oe = 0; 257 258 icount = &info->icount; 259 260 status = UART_LSR_DR; /* We obviously have a character! */ 261 serdatr = custom.serdatr; 262 mb(); 263 custom.intreq = IF_RBF; 264 mb(); 265 266 if((serdatr & 0x1ff) == 0) 267 status |= UART_LSR_BI; 268 if(serdatr & SDR_OVRUN) 269 status |= UART_LSR_OE; 270 271 ch = serdatr & 0xff; 272 icount->rx++; 273 274 #ifdef SERIAL_DEBUG_INTR 275 printk("DR%02x:%02x...", ch, status); 276 #endif 277 flag = TTY_NORMAL; 278 279 /* 280 * We don't handle parity or frame errors - but I have left 281 * the code in, since I'm not sure that the errors can't be 282 * detected. 283 */ 284 285 if (status & (UART_LSR_BI | UART_LSR_PE | 286 UART_LSR_FE | UART_LSR_OE)) { 287 /* 288 * For statistics only 289 */ 290 if (status & UART_LSR_BI) { 291 status &= ~(UART_LSR_FE | UART_LSR_PE); 292 icount->brk++; 293 } else if (status & UART_LSR_PE) 294 icount->parity++; 295 else if (status & UART_LSR_FE) 296 icount->frame++; 297 if (status & UART_LSR_OE) 298 icount->overrun++; 299 300 /* 301 * Now check to see if character should be 302 * ignored, and mask off conditions which 303 * should be ignored. 304 */ 305 if (status & info->ignore_status_mask) 306 goto out; 307 308 status &= info->read_status_mask; 309 310 if (status & (UART_LSR_BI)) { 311 #ifdef SERIAL_DEBUG_INTR 312 printk("handling break...."); 313 #endif 314 flag = TTY_BREAK; 315 if (info->tport.flags & ASYNC_SAK) 316 do_SAK(info->tport.tty); 317 } else if (status & UART_LSR_PE) 318 flag = TTY_PARITY; 319 else if (status & UART_LSR_FE) 320 flag = TTY_FRAME; 321 if (status & UART_LSR_OE) { 322 /* 323 * Overrun is special, since it's 324 * reported immediately, and doesn't 325 * affect the current character 326 */ 327 oe = 1; 328 } 329 } 330 tty_insert_flip_char(&info->tport, ch, flag); 331 if (oe == 1) 332 tty_insert_flip_char(&info->tport, 0, TTY_OVERRUN); 333 tty_flip_buffer_push(&info->tport); 334 out: 335 return; 336 } 337 338 static void transmit_chars(struct serial_state *info) 339 { 340 custom.intreq = IF_TBE; 341 mb(); 342 if (info->x_char) { 343 custom.serdat = info->x_char | 0x100; 344 mb(); 345 info->icount.tx++; 346 info->x_char = 0; 347 return; 348 } 349 if (info->xmit.head == info->xmit.tail 350 || info->tport.tty->stopped 351 || info->tport.tty->hw_stopped) { 352 info->IER &= ~UART_IER_THRI; 353 custom.intena = IF_TBE; 354 mb(); 355 return; 356 } 357 358 custom.serdat = info->xmit.buf[info->xmit.tail++] | 0x100; 359 mb(); 360 info->xmit.tail = info->xmit.tail & (SERIAL_XMIT_SIZE-1); 361 info->icount.tx++; 362 363 if (CIRC_CNT(info->xmit.head, 364 info->xmit.tail, 365 SERIAL_XMIT_SIZE) < WAKEUP_CHARS) 366 tty_wakeup(info->tport.tty); 367 368 #ifdef SERIAL_DEBUG_INTR 369 printk("THRE..."); 370 #endif 371 if (info->xmit.head == info->xmit.tail) { 372 custom.intena = IF_TBE; 373 mb(); 374 info->IER &= ~UART_IER_THRI; 375 } 376 } 377 378 static void check_modem_status(struct serial_state *info) 379 { 380 struct tty_port *port = &info->tport; 381 unsigned char status = ciab.pra & (SER_DCD | SER_CTS | SER_DSR); 382 unsigned char dstatus; 383 struct async_icount *icount; 384 385 /* Determine bits that have changed */ 386 dstatus = status ^ current_ctl_bits; 387 current_ctl_bits = status; 388 389 if (dstatus) { 390 icount = &info->icount; 391 /* update input line counters */ 392 if (dstatus & SER_DSR) 393 icount->dsr++; 394 if (dstatus & SER_DCD) { 395 icount->dcd++; 396 } 397 if (dstatus & SER_CTS) 398 icount->cts++; 399 wake_up_interruptible(&port->delta_msr_wait); 400 } 401 402 if ((port->flags & ASYNC_CHECK_CD) && (dstatus & SER_DCD)) { 403 #if (defined(SERIAL_DEBUG_OPEN) || defined(SERIAL_DEBUG_INTR)) 404 printk("ttyS%d CD now %s...", info->line, 405 (!(status & SER_DCD)) ? "on" : "off"); 406 #endif 407 if (!(status & SER_DCD)) 408 wake_up_interruptible(&port->open_wait); 409 else { 410 #ifdef SERIAL_DEBUG_OPEN 411 printk("doing serial hangup..."); 412 #endif 413 if (port->tty) 414 tty_hangup(port->tty); 415 } 416 } 417 if (tty_port_cts_enabled(port)) { 418 if (port->tty->hw_stopped) { 419 if (!(status & SER_CTS)) { 420 #if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW)) 421 printk("CTS tx start..."); 422 #endif 423 port->tty->hw_stopped = 0; 424 info->IER |= UART_IER_THRI; 425 custom.intena = IF_SETCLR | IF_TBE; 426 mb(); 427 /* set a pending Tx Interrupt, transmitter should restart now */ 428 custom.intreq = IF_SETCLR | IF_TBE; 429 mb(); 430 tty_wakeup(port->tty); 431 return; 432 } 433 } else { 434 if ((status & SER_CTS)) { 435 #if (defined(SERIAL_DEBUG_INTR) || defined(SERIAL_DEBUG_FLOW)) 436 printk("CTS tx stop..."); 437 #endif 438 port->tty->hw_stopped = 1; 439 info->IER &= ~UART_IER_THRI; 440 /* disable Tx interrupt and remove any pending interrupts */ 441 custom.intena = IF_TBE; 442 mb(); 443 custom.intreq = IF_TBE; 444 mb(); 445 } 446 } 447 } 448 } 449 450 static irqreturn_t ser_vbl_int( int irq, void *data) 451 { 452 /* vbl is just a periodic interrupt we tie into to update modem status */ 453 struct serial_state *info = data; 454 /* 455 * TBD - is it better to unregister from this interrupt or to 456 * ignore it if MSI is clear ? 457 */ 458 if(info->IER & UART_IER_MSI) 459 check_modem_status(info); 460 return IRQ_HANDLED; 461 } 462 463 static irqreturn_t ser_rx_int(int irq, void *dev_id) 464 { 465 struct serial_state *info = dev_id; 466 467 #ifdef SERIAL_DEBUG_INTR 468 printk("ser_rx_int..."); 469 #endif 470 471 if (!info->tport.tty) 472 return IRQ_NONE; 473 474 receive_chars(info); 475 #ifdef SERIAL_DEBUG_INTR 476 printk("end.\n"); 477 #endif 478 return IRQ_HANDLED; 479 } 480 481 static irqreturn_t ser_tx_int(int irq, void *dev_id) 482 { 483 struct serial_state *info = dev_id; 484 485 if (custom.serdatr & SDR_TBE) { 486 #ifdef SERIAL_DEBUG_INTR 487 printk("ser_tx_int..."); 488 #endif 489 490 if (!info->tport.tty) 491 return IRQ_NONE; 492 493 transmit_chars(info); 494 #ifdef SERIAL_DEBUG_INTR 495 printk("end.\n"); 496 #endif 497 } 498 return IRQ_HANDLED; 499 } 500 501 /* 502 * ------------------------------------------------------------------- 503 * Here ends the serial interrupt routines. 504 * ------------------------------------------------------------------- 505 */ 506 507 /* 508 * --------------------------------------------------------------- 509 * Low level utility subroutines for the serial driver: routines to 510 * figure out the appropriate timeout for an interrupt chain, routines 511 * to initialize and startup a serial port, and routines to shutdown a 512 * serial port. Useful stuff like that. 513 * --------------------------------------------------------------- 514 */ 515 516 static int startup(struct tty_struct *tty, struct serial_state *info) 517 { 518 struct tty_port *port = &info->tport; 519 unsigned long flags; 520 int retval=0; 521 unsigned long page; 522 523 page = get_zeroed_page(GFP_KERNEL); 524 if (!page) 525 return -ENOMEM; 526 527 local_irq_save(flags); 528 529 if (port->flags & ASYNC_INITIALIZED) { 530 free_page(page); 531 goto errout; 532 } 533 534 if (info->xmit.buf) 535 free_page(page); 536 else 537 info->xmit.buf = (unsigned char *) page; 538 539 #ifdef SERIAL_DEBUG_OPEN 540 printk("starting up ttys%d ...", info->line); 541 #endif 542 543 /* Clear anything in the input buffer */ 544 545 custom.intreq = IF_RBF; 546 mb(); 547 548 retval = request_irq(IRQ_AMIGA_VERTB, ser_vbl_int, 0, "serial status", info); 549 if (retval) { 550 if (serial_isroot()) { 551 set_bit(TTY_IO_ERROR, &tty->flags); 552 retval = 0; 553 } 554 goto errout; 555 } 556 557 /* enable both Rx and Tx interrupts */ 558 custom.intena = IF_SETCLR | IF_RBF | IF_TBE; 559 mb(); 560 info->IER = UART_IER_MSI; 561 562 /* remember current state of the DCD and CTS bits */ 563 current_ctl_bits = ciab.pra & (SER_DCD | SER_CTS | SER_DSR); 564 565 info->MCR = 0; 566 if (C_BAUD(tty)) 567 info->MCR = SER_DTR | SER_RTS; 568 rtsdtr_ctrl(info->MCR); 569 570 clear_bit(TTY_IO_ERROR, &tty->flags); 571 info->xmit.head = info->xmit.tail = 0; 572 573 /* 574 * Set up the tty->alt_speed kludge 575 */ 576 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI) 577 tty->alt_speed = 57600; 578 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI) 579 tty->alt_speed = 115200; 580 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI) 581 tty->alt_speed = 230400; 582 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP) 583 tty->alt_speed = 460800; 584 585 /* 586 * and set the speed of the serial port 587 */ 588 change_speed(tty, info, NULL); 589 590 port->flags |= ASYNC_INITIALIZED; 591 local_irq_restore(flags); 592 return 0; 593 594 errout: 595 local_irq_restore(flags); 596 return retval; 597 } 598 599 /* 600 * This routine will shutdown a serial port; interrupts are disabled, and 601 * DTR is dropped if the hangup on close termio flag is on. 602 */ 603 static void shutdown(struct tty_struct *tty, struct serial_state *info) 604 { 605 unsigned long flags; 606 struct serial_state *state; 607 608 if (!(info->tport.flags & ASYNC_INITIALIZED)) 609 return; 610 611 state = info; 612 613 #ifdef SERIAL_DEBUG_OPEN 614 printk("Shutting down serial port %d ....\n", info->line); 615 #endif 616 617 local_irq_save(flags); /* Disable interrupts */ 618 619 /* 620 * clear delta_msr_wait queue to avoid mem leaks: we may free the irq 621 * here so the queue might never be waken up 622 */ 623 wake_up_interruptible(&info->tport.delta_msr_wait); 624 625 /* 626 * Free the IRQ, if necessary 627 */ 628 free_irq(IRQ_AMIGA_VERTB, info); 629 630 if (info->xmit.buf) { 631 free_page((unsigned long) info->xmit.buf); 632 info->xmit.buf = NULL; 633 } 634 635 info->IER = 0; 636 custom.intena = IF_RBF | IF_TBE; 637 mb(); 638 639 /* disable break condition */ 640 custom.adkcon = AC_UARTBRK; 641 mb(); 642 643 if (tty->termios.c_cflag & HUPCL) 644 info->MCR &= ~(SER_DTR|SER_RTS); 645 rtsdtr_ctrl(info->MCR); 646 647 set_bit(TTY_IO_ERROR, &tty->flags); 648 649 info->tport.flags &= ~ASYNC_INITIALIZED; 650 local_irq_restore(flags); 651 } 652 653 654 /* 655 * This routine is called to set the UART divisor registers to match 656 * the specified baud rate for a serial port. 657 */ 658 static void change_speed(struct tty_struct *tty, struct serial_state *info, 659 struct ktermios *old_termios) 660 { 661 struct tty_port *port = &info->tport; 662 int quot = 0, baud_base, baud; 663 unsigned cflag, cval = 0; 664 int bits; 665 unsigned long flags; 666 667 cflag = tty->termios.c_cflag; 668 669 /* Byte size is always 8 bits plus parity bit if requested */ 670 671 cval = 3; bits = 10; 672 if (cflag & CSTOPB) { 673 cval |= 0x04; 674 bits++; 675 } 676 if (cflag & PARENB) { 677 cval |= UART_LCR_PARITY; 678 bits++; 679 } 680 if (!(cflag & PARODD)) 681 cval |= UART_LCR_EPAR; 682 #ifdef CMSPAR 683 if (cflag & CMSPAR) 684 cval |= UART_LCR_SPAR; 685 #endif 686 687 /* Determine divisor based on baud rate */ 688 baud = tty_get_baud_rate(tty); 689 if (!baud) 690 baud = 9600; /* B0 transition handled in rs_set_termios */ 691 baud_base = info->baud_base; 692 if (baud == 38400 && (port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) 693 quot = info->custom_divisor; 694 else { 695 if (baud == 134) 696 /* Special case since 134 is really 134.5 */ 697 quot = (2*baud_base / 269); 698 else if (baud) 699 quot = baud_base / baud; 700 } 701 /* If the quotient is zero refuse the change */ 702 if (!quot && old_termios) { 703 /* FIXME: Will need updating for new tty in the end */ 704 tty->termios.c_cflag &= ~CBAUD; 705 tty->termios.c_cflag |= (old_termios->c_cflag & CBAUD); 706 baud = tty_get_baud_rate(tty); 707 if (!baud) 708 baud = 9600; 709 if (baud == 38400 && 710 (port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST) 711 quot = info->custom_divisor; 712 else { 713 if (baud == 134) 714 /* Special case since 134 is really 134.5 */ 715 quot = (2*baud_base / 269); 716 else if (baud) 717 quot = baud_base / baud; 718 } 719 } 720 /* As a last resort, if the quotient is zero, default to 9600 bps */ 721 if (!quot) 722 quot = baud_base / 9600; 723 info->quot = quot; 724 info->timeout = ((info->xmit_fifo_size*HZ*bits*quot) / baud_base); 725 info->timeout += HZ/50; /* Add .02 seconds of slop */ 726 727 /* CTS flow control flag and modem status interrupts */ 728 info->IER &= ~UART_IER_MSI; 729 if (port->flags & ASYNC_HARDPPS_CD) 730 info->IER |= UART_IER_MSI; 731 if (cflag & CRTSCTS) { 732 port->flags |= ASYNC_CTS_FLOW; 733 info->IER |= UART_IER_MSI; 734 } else 735 port->flags &= ~ASYNC_CTS_FLOW; 736 if (cflag & CLOCAL) 737 port->flags &= ~ASYNC_CHECK_CD; 738 else { 739 port->flags |= ASYNC_CHECK_CD; 740 info->IER |= UART_IER_MSI; 741 } 742 /* TBD: 743 * Does clearing IER_MSI imply that we should disable the VBL interrupt ? 744 */ 745 746 /* 747 * Set up parity check flag 748 */ 749 750 info->read_status_mask = UART_LSR_OE | UART_LSR_DR; 751 if (I_INPCK(tty)) 752 info->read_status_mask |= UART_LSR_FE | UART_LSR_PE; 753 if (I_BRKINT(tty) || I_PARMRK(tty)) 754 info->read_status_mask |= UART_LSR_BI; 755 756 /* 757 * Characters to ignore 758 */ 759 info->ignore_status_mask = 0; 760 if (I_IGNPAR(tty)) 761 info->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; 762 if (I_IGNBRK(tty)) { 763 info->ignore_status_mask |= UART_LSR_BI; 764 /* 765 * If we're ignore parity and break indicators, ignore 766 * overruns too. (For real raw support). 767 */ 768 if (I_IGNPAR(tty)) 769 info->ignore_status_mask |= UART_LSR_OE; 770 } 771 /* 772 * !!! ignore all characters if CREAD is not set 773 */ 774 if ((cflag & CREAD) == 0) 775 info->ignore_status_mask |= UART_LSR_DR; 776 local_irq_save(flags); 777 778 { 779 short serper; 780 781 /* Set up the baud rate */ 782 serper = quot - 1; 783 784 /* Enable or disable parity bit */ 785 786 if(cval & UART_LCR_PARITY) 787 serper |= (SERPER_PARENB); 788 789 custom.serper = serper; 790 mb(); 791 } 792 793 local_irq_restore(flags); 794 } 795 796 static int rs_put_char(struct tty_struct *tty, unsigned char ch) 797 { 798 struct serial_state *info; 799 unsigned long flags; 800 801 info = tty->driver_data; 802 803 if (serial_paranoia_check(info, tty->name, "rs_put_char")) 804 return 0; 805 806 if (!info->xmit.buf) 807 return 0; 808 809 local_irq_save(flags); 810 if (CIRC_SPACE(info->xmit.head, 811 info->xmit.tail, 812 SERIAL_XMIT_SIZE) == 0) { 813 local_irq_restore(flags); 814 return 0; 815 } 816 817 info->xmit.buf[info->xmit.head++] = ch; 818 info->xmit.head &= SERIAL_XMIT_SIZE-1; 819 local_irq_restore(flags); 820 return 1; 821 } 822 823 static void rs_flush_chars(struct tty_struct *tty) 824 { 825 struct serial_state *info = tty->driver_data; 826 unsigned long flags; 827 828 if (serial_paranoia_check(info, tty->name, "rs_flush_chars")) 829 return; 830 831 if (info->xmit.head == info->xmit.tail 832 || tty->stopped 833 || tty->hw_stopped 834 || !info->xmit.buf) 835 return; 836 837 local_irq_save(flags); 838 info->IER |= UART_IER_THRI; 839 custom.intena = IF_SETCLR | IF_TBE; 840 mb(); 841 /* set a pending Tx Interrupt, transmitter should restart now */ 842 custom.intreq = IF_SETCLR | IF_TBE; 843 mb(); 844 local_irq_restore(flags); 845 } 846 847 static int rs_write(struct tty_struct * tty, const unsigned char *buf, int count) 848 { 849 int c, ret = 0; 850 struct serial_state *info = tty->driver_data; 851 unsigned long flags; 852 853 if (serial_paranoia_check(info, tty->name, "rs_write")) 854 return 0; 855 856 if (!info->xmit.buf) 857 return 0; 858 859 local_irq_save(flags); 860 while (1) { 861 c = CIRC_SPACE_TO_END(info->xmit.head, 862 info->xmit.tail, 863 SERIAL_XMIT_SIZE); 864 if (count < c) 865 c = count; 866 if (c <= 0) { 867 break; 868 } 869 memcpy(info->xmit.buf + info->xmit.head, buf, c); 870 info->xmit.head = ((info->xmit.head + c) & 871 (SERIAL_XMIT_SIZE-1)); 872 buf += c; 873 count -= c; 874 ret += c; 875 } 876 local_irq_restore(flags); 877 878 if (info->xmit.head != info->xmit.tail 879 && !tty->stopped 880 && !tty->hw_stopped 881 && !(info->IER & UART_IER_THRI)) { 882 info->IER |= UART_IER_THRI; 883 local_irq_disable(); 884 custom.intena = IF_SETCLR | IF_TBE; 885 mb(); 886 /* set a pending Tx Interrupt, transmitter should restart now */ 887 custom.intreq = IF_SETCLR | IF_TBE; 888 mb(); 889 local_irq_restore(flags); 890 } 891 return ret; 892 } 893 894 static int rs_write_room(struct tty_struct *tty) 895 { 896 struct serial_state *info = tty->driver_data; 897 898 if (serial_paranoia_check(info, tty->name, "rs_write_room")) 899 return 0; 900 return CIRC_SPACE(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE); 901 } 902 903 static int rs_chars_in_buffer(struct tty_struct *tty) 904 { 905 struct serial_state *info = tty->driver_data; 906 907 if (serial_paranoia_check(info, tty->name, "rs_chars_in_buffer")) 908 return 0; 909 return CIRC_CNT(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE); 910 } 911 912 static void rs_flush_buffer(struct tty_struct *tty) 913 { 914 struct serial_state *info = tty->driver_data; 915 unsigned long flags; 916 917 if (serial_paranoia_check(info, tty->name, "rs_flush_buffer")) 918 return; 919 local_irq_save(flags); 920 info->xmit.head = info->xmit.tail = 0; 921 local_irq_restore(flags); 922 tty_wakeup(tty); 923 } 924 925 /* 926 * This function is used to send a high-priority XON/XOFF character to 927 * the device 928 */ 929 static void rs_send_xchar(struct tty_struct *tty, char ch) 930 { 931 struct serial_state *info = tty->driver_data; 932 unsigned long flags; 933 934 if (serial_paranoia_check(info, tty->name, "rs_send_char")) 935 return; 936 937 info->x_char = ch; 938 if (ch) { 939 /* Make sure transmit interrupts are on */ 940 941 /* Check this ! */ 942 local_irq_save(flags); 943 if(!(custom.intenar & IF_TBE)) { 944 custom.intena = IF_SETCLR | IF_TBE; 945 mb(); 946 /* set a pending Tx Interrupt, transmitter should restart now */ 947 custom.intreq = IF_SETCLR | IF_TBE; 948 mb(); 949 } 950 local_irq_restore(flags); 951 952 info->IER |= UART_IER_THRI; 953 } 954 } 955 956 /* 957 * ------------------------------------------------------------ 958 * rs_throttle() 959 * 960 * This routine is called by the upper-layer tty layer to signal that 961 * incoming characters should be throttled. 962 * ------------------------------------------------------------ 963 */ 964 static void rs_throttle(struct tty_struct * tty) 965 { 966 struct serial_state *info = tty->driver_data; 967 unsigned long flags; 968 #ifdef SERIAL_DEBUG_THROTTLE 969 char buf[64]; 970 971 printk("throttle %s: %d....\n", tty_name(tty, buf), 972 tty->ldisc.chars_in_buffer(tty)); 973 #endif 974 975 if (serial_paranoia_check(info, tty->name, "rs_throttle")) 976 return; 977 978 if (I_IXOFF(tty)) 979 rs_send_xchar(tty, STOP_CHAR(tty)); 980 981 if (tty->termios.c_cflag & CRTSCTS) 982 info->MCR &= ~SER_RTS; 983 984 local_irq_save(flags); 985 rtsdtr_ctrl(info->MCR); 986 local_irq_restore(flags); 987 } 988 989 static void rs_unthrottle(struct tty_struct * tty) 990 { 991 struct serial_state *info = tty->driver_data; 992 unsigned long flags; 993 #ifdef SERIAL_DEBUG_THROTTLE 994 char buf[64]; 995 996 printk("unthrottle %s: %d....\n", tty_name(tty, buf), 997 tty->ldisc.chars_in_buffer(tty)); 998 #endif 999 1000 if (serial_paranoia_check(info, tty->name, "rs_unthrottle")) 1001 return; 1002 1003 if (I_IXOFF(tty)) { 1004 if (info->x_char) 1005 info->x_char = 0; 1006 else 1007 rs_send_xchar(tty, START_CHAR(tty)); 1008 } 1009 if (tty->termios.c_cflag & CRTSCTS) 1010 info->MCR |= SER_RTS; 1011 local_irq_save(flags); 1012 rtsdtr_ctrl(info->MCR); 1013 local_irq_restore(flags); 1014 } 1015 1016 /* 1017 * ------------------------------------------------------------ 1018 * rs_ioctl() and friends 1019 * ------------------------------------------------------------ 1020 */ 1021 1022 static int get_serial_info(struct tty_struct *tty, struct serial_state *state, 1023 struct serial_struct __user * retinfo) 1024 { 1025 struct serial_struct tmp; 1026 1027 if (!retinfo) 1028 return -EFAULT; 1029 memset(&tmp, 0, sizeof(tmp)); 1030 tty_lock(tty); 1031 tmp.line = tty->index; 1032 tmp.port = state->port; 1033 tmp.flags = state->tport.flags; 1034 tmp.xmit_fifo_size = state->xmit_fifo_size; 1035 tmp.baud_base = state->baud_base; 1036 tmp.close_delay = state->tport.close_delay; 1037 tmp.closing_wait = state->tport.closing_wait; 1038 tmp.custom_divisor = state->custom_divisor; 1039 tty_unlock(tty); 1040 if (copy_to_user(retinfo,&tmp,sizeof(*retinfo))) 1041 return -EFAULT; 1042 return 0; 1043 } 1044 1045 static int set_serial_info(struct tty_struct *tty, struct serial_state *state, 1046 struct serial_struct __user * new_info) 1047 { 1048 struct tty_port *port = &state->tport; 1049 struct serial_struct new_serial; 1050 bool change_spd; 1051 int retval = 0; 1052 1053 if (copy_from_user(&new_serial,new_info,sizeof(new_serial))) 1054 return -EFAULT; 1055 1056 tty_lock(tty); 1057 change_spd = ((new_serial.flags ^ port->flags) & ASYNC_SPD_MASK) || 1058 new_serial.custom_divisor != state->custom_divisor; 1059 if (new_serial.irq || new_serial.port != state->port || 1060 new_serial.xmit_fifo_size != state->xmit_fifo_size) { 1061 tty_unlock(tty); 1062 return -EINVAL; 1063 } 1064 1065 if (!serial_isroot()) { 1066 if ((new_serial.baud_base != state->baud_base) || 1067 (new_serial.close_delay != port->close_delay) || 1068 (new_serial.xmit_fifo_size != state->xmit_fifo_size) || 1069 ((new_serial.flags & ~ASYNC_USR_MASK) != 1070 (port->flags & ~ASYNC_USR_MASK))) { 1071 tty_unlock(tty); 1072 return -EPERM; 1073 } 1074 port->flags = ((port->flags & ~ASYNC_USR_MASK) | 1075 (new_serial.flags & ASYNC_USR_MASK)); 1076 state->custom_divisor = new_serial.custom_divisor; 1077 goto check_and_exit; 1078 } 1079 1080 if (new_serial.baud_base < 9600) { 1081 tty_unlock(tty); 1082 return -EINVAL; 1083 } 1084 1085 /* 1086 * OK, past this point, all the error checking has been done. 1087 * At this point, we start making changes..... 1088 */ 1089 1090 state->baud_base = new_serial.baud_base; 1091 port->flags = ((port->flags & ~ASYNC_FLAGS) | 1092 (new_serial.flags & ASYNC_FLAGS)); 1093 state->custom_divisor = new_serial.custom_divisor; 1094 port->close_delay = new_serial.close_delay * HZ/100; 1095 port->closing_wait = new_serial.closing_wait * HZ/100; 1096 port->low_latency = (port->flags & ASYNC_LOW_LATENCY) ? 1 : 0; 1097 1098 check_and_exit: 1099 if (port->flags & ASYNC_INITIALIZED) { 1100 if (change_spd) { 1101 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI) 1102 tty->alt_speed = 57600; 1103 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI) 1104 tty->alt_speed = 115200; 1105 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI) 1106 tty->alt_speed = 230400; 1107 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP) 1108 tty->alt_speed = 460800; 1109 change_speed(tty, state, NULL); 1110 } 1111 } else 1112 retval = startup(tty, state); 1113 tty_unlock(tty); 1114 return retval; 1115 } 1116 1117 1118 /* 1119 * get_lsr_info - get line status register info 1120 * 1121 * Purpose: Let user call ioctl() to get info when the UART physically 1122 * is emptied. On bus types like RS485, the transmitter must 1123 * release the bus after transmitting. This must be done when 1124 * the transmit shift register is empty, not be done when the 1125 * transmit holding register is empty. This functionality 1126 * allows an RS485 driver to be written in user space. 1127 */ 1128 static int get_lsr_info(struct serial_state *info, unsigned int __user *value) 1129 { 1130 unsigned char status; 1131 unsigned int result; 1132 unsigned long flags; 1133 1134 local_irq_save(flags); 1135 status = custom.serdatr; 1136 mb(); 1137 local_irq_restore(flags); 1138 result = ((status & SDR_TSRE) ? TIOCSER_TEMT : 0); 1139 if (copy_to_user(value, &result, sizeof(int))) 1140 return -EFAULT; 1141 return 0; 1142 } 1143 1144 1145 static int rs_tiocmget(struct tty_struct *tty) 1146 { 1147 struct serial_state *info = tty->driver_data; 1148 unsigned char control, status; 1149 unsigned long flags; 1150 1151 if (serial_paranoia_check(info, tty->name, "rs_ioctl")) 1152 return -ENODEV; 1153 if (tty->flags & (1 << TTY_IO_ERROR)) 1154 return -EIO; 1155 1156 control = info->MCR; 1157 local_irq_save(flags); 1158 status = ciab.pra; 1159 local_irq_restore(flags); 1160 return ((control & SER_RTS) ? TIOCM_RTS : 0) 1161 | ((control & SER_DTR) ? TIOCM_DTR : 0) 1162 | (!(status & SER_DCD) ? TIOCM_CAR : 0) 1163 | (!(status & SER_DSR) ? TIOCM_DSR : 0) 1164 | (!(status & SER_CTS) ? TIOCM_CTS : 0); 1165 } 1166 1167 static int rs_tiocmset(struct tty_struct *tty, unsigned int set, 1168 unsigned int clear) 1169 { 1170 struct serial_state *info = tty->driver_data; 1171 unsigned long flags; 1172 1173 if (serial_paranoia_check(info, tty->name, "rs_ioctl")) 1174 return -ENODEV; 1175 if (tty->flags & (1 << TTY_IO_ERROR)) 1176 return -EIO; 1177 1178 local_irq_save(flags); 1179 if (set & TIOCM_RTS) 1180 info->MCR |= SER_RTS; 1181 if (set & TIOCM_DTR) 1182 info->MCR |= SER_DTR; 1183 if (clear & TIOCM_RTS) 1184 info->MCR &= ~SER_RTS; 1185 if (clear & TIOCM_DTR) 1186 info->MCR &= ~SER_DTR; 1187 rtsdtr_ctrl(info->MCR); 1188 local_irq_restore(flags); 1189 return 0; 1190 } 1191 1192 /* 1193 * rs_break() --- routine which turns the break handling on or off 1194 */ 1195 static int rs_break(struct tty_struct *tty, int break_state) 1196 { 1197 struct serial_state *info = tty->driver_data; 1198 unsigned long flags; 1199 1200 if (serial_paranoia_check(info, tty->name, "rs_break")) 1201 return -EINVAL; 1202 1203 local_irq_save(flags); 1204 if (break_state == -1) 1205 custom.adkcon = AC_SETCLR | AC_UARTBRK; 1206 else 1207 custom.adkcon = AC_UARTBRK; 1208 mb(); 1209 local_irq_restore(flags); 1210 return 0; 1211 } 1212 1213 /* 1214 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS) 1215 * Return: write counters to the user passed counter struct 1216 * NB: both 1->0 and 0->1 transitions are counted except for 1217 * RI where only 0->1 is counted. 1218 */ 1219 static int rs_get_icount(struct tty_struct *tty, 1220 struct serial_icounter_struct *icount) 1221 { 1222 struct serial_state *info = tty->driver_data; 1223 struct async_icount cnow; 1224 unsigned long flags; 1225 1226 local_irq_save(flags); 1227 cnow = info->icount; 1228 local_irq_restore(flags); 1229 icount->cts = cnow.cts; 1230 icount->dsr = cnow.dsr; 1231 icount->rng = cnow.rng; 1232 icount->dcd = cnow.dcd; 1233 icount->rx = cnow.rx; 1234 icount->tx = cnow.tx; 1235 icount->frame = cnow.frame; 1236 icount->overrun = cnow.overrun; 1237 icount->parity = cnow.parity; 1238 icount->brk = cnow.brk; 1239 icount->buf_overrun = cnow.buf_overrun; 1240 1241 return 0; 1242 } 1243 1244 static int rs_ioctl(struct tty_struct *tty, 1245 unsigned int cmd, unsigned long arg) 1246 { 1247 struct serial_state *info = tty->driver_data; 1248 struct async_icount cprev, cnow; /* kernel counter temps */ 1249 void __user *argp = (void __user *)arg; 1250 unsigned long flags; 1251 DEFINE_WAIT(wait); 1252 int ret; 1253 1254 if (serial_paranoia_check(info, tty->name, "rs_ioctl")) 1255 return -ENODEV; 1256 1257 if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) && 1258 (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGSTRUCT) && 1259 (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) { 1260 if (tty->flags & (1 << TTY_IO_ERROR)) 1261 return -EIO; 1262 } 1263 1264 switch (cmd) { 1265 case TIOCGSERIAL: 1266 return get_serial_info(tty, info, argp); 1267 case TIOCSSERIAL: 1268 return set_serial_info(tty, info, argp); 1269 case TIOCSERCONFIG: 1270 return 0; 1271 1272 case TIOCSERGETLSR: /* Get line status register */ 1273 return get_lsr_info(info, argp); 1274 1275 case TIOCSERGSTRUCT: 1276 if (copy_to_user(argp, 1277 info, sizeof(struct serial_state))) 1278 return -EFAULT; 1279 return 0; 1280 1281 /* 1282 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change 1283 * - mask passed in arg for lines of interest 1284 * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) 1285 * Caller should use TIOCGICOUNT to see which one it was 1286 */ 1287 case TIOCMIWAIT: 1288 local_irq_save(flags); 1289 /* note the counters on entry */ 1290 cprev = info->icount; 1291 local_irq_restore(flags); 1292 while (1) { 1293 prepare_to_wait(&info->tport.delta_msr_wait, 1294 &wait, TASK_INTERRUPTIBLE); 1295 local_irq_save(flags); 1296 cnow = info->icount; /* atomic copy */ 1297 local_irq_restore(flags); 1298 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && 1299 cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) { 1300 ret = -EIO; /* no change => error */ 1301 break; 1302 } 1303 if ( ((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) || 1304 ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) || 1305 ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) || 1306 ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts)) ) { 1307 ret = 0; 1308 break; 1309 } 1310 schedule(); 1311 /* see if a signal did it */ 1312 if (signal_pending(current)) { 1313 ret = -ERESTARTSYS; 1314 break; 1315 } 1316 cprev = cnow; 1317 } 1318 finish_wait(&info->tport.delta_msr_wait, &wait); 1319 return ret; 1320 1321 case TIOCSERGWILD: 1322 case TIOCSERSWILD: 1323 /* "setserial -W" is called in Debian boot */ 1324 printk ("TIOCSER?WILD ioctl obsolete, ignored.\n"); 1325 return 0; 1326 1327 default: 1328 return -ENOIOCTLCMD; 1329 } 1330 return 0; 1331 } 1332 1333 static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios) 1334 { 1335 struct serial_state *info = tty->driver_data; 1336 unsigned long flags; 1337 unsigned int cflag = tty->termios.c_cflag; 1338 1339 change_speed(tty, info, old_termios); 1340 1341 /* Handle transition to B0 status */ 1342 if ((old_termios->c_cflag & CBAUD) && 1343 !(cflag & CBAUD)) { 1344 info->MCR &= ~(SER_DTR|SER_RTS); 1345 local_irq_save(flags); 1346 rtsdtr_ctrl(info->MCR); 1347 local_irq_restore(flags); 1348 } 1349 1350 /* Handle transition away from B0 status */ 1351 if (!(old_termios->c_cflag & CBAUD) && 1352 (cflag & CBAUD)) { 1353 info->MCR |= SER_DTR; 1354 if (!(tty->termios.c_cflag & CRTSCTS) || 1355 !test_bit(TTY_THROTTLED, &tty->flags)) { 1356 info->MCR |= SER_RTS; 1357 } 1358 local_irq_save(flags); 1359 rtsdtr_ctrl(info->MCR); 1360 local_irq_restore(flags); 1361 } 1362 1363 /* Handle turning off CRTSCTS */ 1364 if ((old_termios->c_cflag & CRTSCTS) && 1365 !(tty->termios.c_cflag & CRTSCTS)) { 1366 tty->hw_stopped = 0; 1367 rs_start(tty); 1368 } 1369 1370 #if 0 1371 /* 1372 * No need to wake up processes in open wait, since they 1373 * sample the CLOCAL flag once, and don't recheck it. 1374 * XXX It's not clear whether the current behavior is correct 1375 * or not. Hence, this may change..... 1376 */ 1377 if (!(old_termios->c_cflag & CLOCAL) && 1378 (tty->termios.c_cflag & CLOCAL)) 1379 wake_up_interruptible(&info->open_wait); 1380 #endif 1381 } 1382 1383 /* 1384 * ------------------------------------------------------------ 1385 * rs_close() 1386 * 1387 * This routine is called when the serial port gets closed. First, we 1388 * wait for the last remaining data to be sent. Then, we unlink its 1389 * async structure from the interrupt chain if necessary, and we free 1390 * that IRQ if nothing is left in the chain. 1391 * ------------------------------------------------------------ 1392 */ 1393 static void rs_close(struct tty_struct *tty, struct file * filp) 1394 { 1395 struct serial_state *state = tty->driver_data; 1396 struct tty_port *port = &state->tport; 1397 1398 if (serial_paranoia_check(state, tty->name, "rs_close")) 1399 return; 1400 1401 if (tty_port_close_start(port, tty, filp) == 0) 1402 return; 1403 1404 /* 1405 * At this point we stop accepting input. To do this, we 1406 * disable the receive line status interrupts, and tell the 1407 * interrupt driver to stop checking the data ready bit in the 1408 * line status register. 1409 */ 1410 state->read_status_mask &= ~UART_LSR_DR; 1411 if (port->flags & ASYNC_INITIALIZED) { 1412 /* disable receive interrupts */ 1413 custom.intena = IF_RBF; 1414 mb(); 1415 /* clear any pending receive interrupt */ 1416 custom.intreq = IF_RBF; 1417 mb(); 1418 1419 /* 1420 * Before we drop DTR, make sure the UART transmitter 1421 * has completely drained; this is especially 1422 * important if there is a transmit FIFO! 1423 */ 1424 rs_wait_until_sent(tty, state->timeout); 1425 } 1426 shutdown(tty, state); 1427 rs_flush_buffer(tty); 1428 1429 tty_ldisc_flush(tty); 1430 port->tty = NULL; 1431 1432 tty_port_close_end(port, tty); 1433 } 1434 1435 /* 1436 * rs_wait_until_sent() --- wait until the transmitter is empty 1437 */ 1438 static void rs_wait_until_sent(struct tty_struct *tty, int timeout) 1439 { 1440 struct serial_state *info = tty->driver_data; 1441 unsigned long orig_jiffies, char_time; 1442 int lsr; 1443 1444 if (serial_paranoia_check(info, tty->name, "rs_wait_until_sent")) 1445 return; 1446 1447 if (info->xmit_fifo_size == 0) 1448 return; /* Just in case.... */ 1449 1450 orig_jiffies = jiffies; 1451 1452 /* 1453 * Set the check interval to be 1/5 of the estimated time to 1454 * send a single character, and make it at least 1. The check 1455 * interval should also be less than the timeout. 1456 * 1457 * Note: we have to use pretty tight timings here to satisfy 1458 * the NIST-PCTS. 1459 */ 1460 char_time = (info->timeout - HZ/50) / info->xmit_fifo_size; 1461 char_time = char_time / 5; 1462 if (char_time == 0) 1463 char_time = 1; 1464 if (timeout) 1465 char_time = min_t(unsigned long, char_time, timeout); 1466 /* 1467 * If the transmitter hasn't cleared in twice the approximate 1468 * amount of time to send the entire FIFO, it probably won't 1469 * ever clear. This assumes the UART isn't doing flow 1470 * control, which is currently the case. Hence, if it ever 1471 * takes longer than info->timeout, this is probably due to a 1472 * UART bug of some kind. So, we clamp the timeout parameter at 1473 * 2*info->timeout. 1474 */ 1475 if (!timeout || timeout > 2*info->timeout) 1476 timeout = 2*info->timeout; 1477 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT 1478 printk("In rs_wait_until_sent(%d) check=%lu...", timeout, char_time); 1479 printk("jiff=%lu...", jiffies); 1480 #endif 1481 while(!((lsr = custom.serdatr) & SDR_TSRE)) { 1482 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT 1483 printk("serdatr = %d (jiff=%lu)...", lsr, jiffies); 1484 #endif 1485 msleep_interruptible(jiffies_to_msecs(char_time)); 1486 if (signal_pending(current)) 1487 break; 1488 if (timeout && time_after(jiffies, orig_jiffies + timeout)) 1489 break; 1490 } 1491 __set_current_state(TASK_RUNNING); 1492 1493 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT 1494 printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies); 1495 #endif 1496 } 1497 1498 /* 1499 * rs_hangup() --- called by tty_hangup() when a hangup is signaled. 1500 */ 1501 static void rs_hangup(struct tty_struct *tty) 1502 { 1503 struct serial_state *info = tty->driver_data; 1504 1505 if (serial_paranoia_check(info, tty->name, "rs_hangup")) 1506 return; 1507 1508 rs_flush_buffer(tty); 1509 shutdown(tty, info); 1510 info->tport.count = 0; 1511 info->tport.flags &= ~ASYNC_NORMAL_ACTIVE; 1512 info->tport.tty = NULL; 1513 wake_up_interruptible(&info->tport.open_wait); 1514 } 1515 1516 /* 1517 * This routine is called whenever a serial port is opened. It 1518 * enables interrupts for a serial port, linking in its async structure into 1519 * the IRQ chain. It also performs the serial-specific 1520 * initialization for the tty structure. 1521 */ 1522 static int rs_open(struct tty_struct *tty, struct file * filp) 1523 { 1524 struct serial_state *info = rs_table + tty->index; 1525 struct tty_port *port = &info->tport; 1526 int retval; 1527 1528 port->count++; 1529 port->tty = tty; 1530 tty->driver_data = info; 1531 tty->port = port; 1532 if (serial_paranoia_check(info, tty->name, "rs_open")) 1533 return -ENODEV; 1534 1535 port->low_latency = (port->flags & ASYNC_LOW_LATENCY) ? 1 : 0; 1536 1537 retval = startup(tty, info); 1538 if (retval) { 1539 return retval; 1540 } 1541 1542 return tty_port_block_til_ready(port, tty, filp); 1543 } 1544 1545 /* 1546 * /proc fs routines.... 1547 */ 1548 1549 static inline void line_info(struct seq_file *m, int line, 1550 struct serial_state *state) 1551 { 1552 char stat_buf[30], control, status; 1553 unsigned long flags; 1554 1555 seq_printf(m, "%d: uart:amiga_builtin", line); 1556 1557 local_irq_save(flags); 1558 status = ciab.pra; 1559 control = (state->tport.flags & ASYNC_INITIALIZED) ? state->MCR : status; 1560 local_irq_restore(flags); 1561 1562 stat_buf[0] = 0; 1563 stat_buf[1] = 0; 1564 if(!(control & SER_RTS)) 1565 strcat(stat_buf, "|RTS"); 1566 if(!(status & SER_CTS)) 1567 strcat(stat_buf, "|CTS"); 1568 if(!(control & SER_DTR)) 1569 strcat(stat_buf, "|DTR"); 1570 if(!(status & SER_DSR)) 1571 strcat(stat_buf, "|DSR"); 1572 if(!(status & SER_DCD)) 1573 strcat(stat_buf, "|CD"); 1574 1575 if (state->quot) 1576 seq_printf(m, " baud:%d", state->baud_base / state->quot); 1577 1578 seq_printf(m, " tx:%d rx:%d", state->icount.tx, state->icount.rx); 1579 1580 if (state->icount.frame) 1581 seq_printf(m, " fe:%d", state->icount.frame); 1582 1583 if (state->icount.parity) 1584 seq_printf(m, " pe:%d", state->icount.parity); 1585 1586 if (state->icount.brk) 1587 seq_printf(m, " brk:%d", state->icount.brk); 1588 1589 if (state->icount.overrun) 1590 seq_printf(m, " oe:%d", state->icount.overrun); 1591 1592 /* 1593 * Last thing is the RS-232 status lines 1594 */ 1595 seq_printf(m, " %s\n", stat_buf+1); 1596 } 1597 1598 static int rs_proc_show(struct seq_file *m, void *v) 1599 { 1600 seq_printf(m, "serinfo:1.0 driver:%s\n", serial_version); 1601 line_info(m, 0, &rs_table[0]); 1602 return 0; 1603 } 1604 1605 static int rs_proc_open(struct inode *inode, struct file *file) 1606 { 1607 return single_open(file, rs_proc_show, NULL); 1608 } 1609 1610 static const struct file_operations rs_proc_fops = { 1611 .owner = THIS_MODULE, 1612 .open = rs_proc_open, 1613 .read = seq_read, 1614 .llseek = seq_lseek, 1615 .release = single_release, 1616 }; 1617 1618 /* 1619 * --------------------------------------------------------------------- 1620 * rs_init() and friends 1621 * 1622 * rs_init() is called at boot-time to initialize the serial driver. 1623 * --------------------------------------------------------------------- 1624 */ 1625 1626 /* 1627 * This routine prints out the appropriate serial driver version 1628 * number, and identifies which options were configured into this 1629 * driver. 1630 */ 1631 static void show_serial_version(void) 1632 { 1633 printk(KERN_INFO "%s version %s\n", serial_name, serial_version); 1634 } 1635 1636 1637 static const struct tty_operations serial_ops = { 1638 .open = rs_open, 1639 .close = rs_close, 1640 .write = rs_write, 1641 .put_char = rs_put_char, 1642 .flush_chars = rs_flush_chars, 1643 .write_room = rs_write_room, 1644 .chars_in_buffer = rs_chars_in_buffer, 1645 .flush_buffer = rs_flush_buffer, 1646 .ioctl = rs_ioctl, 1647 .throttle = rs_throttle, 1648 .unthrottle = rs_unthrottle, 1649 .set_termios = rs_set_termios, 1650 .stop = rs_stop, 1651 .start = rs_start, 1652 .hangup = rs_hangup, 1653 .break_ctl = rs_break, 1654 .send_xchar = rs_send_xchar, 1655 .wait_until_sent = rs_wait_until_sent, 1656 .tiocmget = rs_tiocmget, 1657 .tiocmset = rs_tiocmset, 1658 .get_icount = rs_get_icount, 1659 .proc_fops = &rs_proc_fops, 1660 }; 1661 1662 static int amiga_carrier_raised(struct tty_port *port) 1663 { 1664 return !(ciab.pra & SER_DCD); 1665 } 1666 1667 static void amiga_dtr_rts(struct tty_port *port, int raise) 1668 { 1669 struct serial_state *info = container_of(port, struct serial_state, 1670 tport); 1671 unsigned long flags; 1672 1673 if (raise) 1674 info->MCR |= SER_DTR|SER_RTS; 1675 else 1676 info->MCR &= ~(SER_DTR|SER_RTS); 1677 1678 local_irq_save(flags); 1679 rtsdtr_ctrl(info->MCR); 1680 local_irq_restore(flags); 1681 } 1682 1683 static const struct tty_port_operations amiga_port_ops = { 1684 .carrier_raised = amiga_carrier_raised, 1685 .dtr_rts = amiga_dtr_rts, 1686 }; 1687 1688 /* 1689 * The serial driver boot-time initialization code! 1690 */ 1691 static int __init amiga_serial_probe(struct platform_device *pdev) 1692 { 1693 unsigned long flags; 1694 struct serial_state * state; 1695 int error; 1696 1697 serial_driver = alloc_tty_driver(NR_PORTS); 1698 if (!serial_driver) 1699 return -ENOMEM; 1700 1701 show_serial_version(); 1702 1703 /* Initialize the tty_driver structure */ 1704 1705 serial_driver->driver_name = "amiserial"; 1706 serial_driver->name = "ttyS"; 1707 serial_driver->major = TTY_MAJOR; 1708 serial_driver->minor_start = 64; 1709 serial_driver->type = TTY_DRIVER_TYPE_SERIAL; 1710 serial_driver->subtype = SERIAL_TYPE_NORMAL; 1711 serial_driver->init_termios = tty_std_termios; 1712 serial_driver->init_termios.c_cflag = 1713 B9600 | CS8 | CREAD | HUPCL | CLOCAL; 1714 serial_driver->flags = TTY_DRIVER_REAL_RAW; 1715 tty_set_operations(serial_driver, &serial_ops); 1716 1717 state = rs_table; 1718 state->port = (int)&custom.serdatr; /* Just to give it a value */ 1719 state->custom_divisor = 0; 1720 state->icount.cts = state->icount.dsr = 1721 state->icount.rng = state->icount.dcd = 0; 1722 state->icount.rx = state->icount.tx = 0; 1723 state->icount.frame = state->icount.parity = 0; 1724 state->icount.overrun = state->icount.brk = 0; 1725 tty_port_init(&state->tport); 1726 state->tport.ops = &amiga_port_ops; 1727 tty_port_link_device(&state->tport, serial_driver, 0); 1728 1729 error = tty_register_driver(serial_driver); 1730 if (error) 1731 goto fail_put_tty_driver; 1732 1733 printk(KERN_INFO "ttyS0 is the amiga builtin serial port\n"); 1734 1735 /* Hardware set up */ 1736 1737 state->baud_base = amiga_colorclock; 1738 state->xmit_fifo_size = 1; 1739 1740 /* set ISRs, and then disable the rx interrupts */ 1741 error = request_irq(IRQ_AMIGA_TBE, ser_tx_int, 0, "serial TX", state); 1742 if (error) 1743 goto fail_unregister; 1744 1745 error = request_irq(IRQ_AMIGA_RBF, ser_rx_int, 0, 1746 "serial RX", state); 1747 if (error) 1748 goto fail_free_irq; 1749 1750 local_irq_save(flags); 1751 1752 /* turn off Rx and Tx interrupts */ 1753 custom.intena = IF_RBF | IF_TBE; 1754 mb(); 1755 1756 /* clear any pending interrupt */ 1757 custom.intreq = IF_RBF | IF_TBE; 1758 mb(); 1759 1760 local_irq_restore(flags); 1761 1762 /* 1763 * set the appropriate directions for the modem control flags, 1764 * and clear RTS and DTR 1765 */ 1766 ciab.ddra |= (SER_DTR | SER_RTS); /* outputs */ 1767 ciab.ddra &= ~(SER_DCD | SER_CTS | SER_DSR); /* inputs */ 1768 1769 platform_set_drvdata(pdev, state); 1770 1771 return 0; 1772 1773 fail_free_irq: 1774 free_irq(IRQ_AMIGA_TBE, state); 1775 fail_unregister: 1776 tty_unregister_driver(serial_driver); 1777 fail_put_tty_driver: 1778 tty_port_destroy(&state->tport); 1779 put_tty_driver(serial_driver); 1780 return error; 1781 } 1782 1783 static int __exit amiga_serial_remove(struct platform_device *pdev) 1784 { 1785 int error; 1786 struct serial_state *state = platform_get_drvdata(pdev); 1787 1788 /* printk("Unloading %s: version %s\n", serial_name, serial_version); */ 1789 if ((error = tty_unregister_driver(serial_driver))) 1790 printk("SERIAL: failed to unregister serial driver (%d)\n", 1791 error); 1792 put_tty_driver(serial_driver); 1793 tty_port_destroy(&state->tport); 1794 1795 free_irq(IRQ_AMIGA_TBE, state); 1796 free_irq(IRQ_AMIGA_RBF, state); 1797 1798 return error; 1799 } 1800 1801 static struct platform_driver amiga_serial_driver = { 1802 .remove = __exit_p(amiga_serial_remove), 1803 .driver = { 1804 .name = "amiga-serial", 1805 .owner = THIS_MODULE, 1806 }, 1807 }; 1808 1809 module_platform_driver_probe(amiga_serial_driver, amiga_serial_probe); 1810 1811 1812 #if defined(CONFIG_SERIAL_CONSOLE) && !defined(MODULE) 1813 1814 /* 1815 * ------------------------------------------------------------ 1816 * Serial console driver 1817 * ------------------------------------------------------------ 1818 */ 1819 1820 static void amiga_serial_putc(char c) 1821 { 1822 custom.serdat = (unsigned char)c | 0x100; 1823 while (!(custom.serdatr & 0x2000)) 1824 barrier(); 1825 } 1826 1827 /* 1828 * Print a string to the serial port trying not to disturb 1829 * any possible real use of the port... 1830 * 1831 * The console must be locked when we get here. 1832 */ 1833 static void serial_console_write(struct console *co, const char *s, 1834 unsigned count) 1835 { 1836 unsigned short intena = custom.intenar; 1837 1838 custom.intena = IF_TBE; 1839 1840 while (count--) { 1841 if (*s == '\n') 1842 amiga_serial_putc('\r'); 1843 amiga_serial_putc(*s++); 1844 } 1845 1846 custom.intena = IF_SETCLR | (intena & IF_TBE); 1847 } 1848 1849 static struct tty_driver *serial_console_device(struct console *c, int *index) 1850 { 1851 *index = 0; 1852 return serial_driver; 1853 } 1854 1855 static struct console sercons = { 1856 .name = "ttyS", 1857 .write = serial_console_write, 1858 .device = serial_console_device, 1859 .flags = CON_PRINTBUFFER, 1860 .index = -1, 1861 }; 1862 1863 /* 1864 * Register console. 1865 */ 1866 static int __init amiserial_console_init(void) 1867 { 1868 if (!MACH_IS_AMIGA) 1869 return -ENODEV; 1870 1871 register_console(&sercons); 1872 return 0; 1873 } 1874 console_initcall(amiserial_console_init); 1875 1876 #endif /* CONFIG_SERIAL_CONSOLE && !MODULE */ 1877 1878 MODULE_LICENSE("GPL"); 1879 MODULE_ALIAS("platform:amiga-serial"); 1880