1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright (c) 2020 Linaro Limited 4 * 5 * Based on original driver: 6 * Copyright (c) 2012-2020, The Linux Foundation. All rights reserved. 7 * 8 * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved. 9 */ 10 11 #include <linux/bitfield.h> 12 #include <linux/iio/adc/qcom-vadc-common.h> 13 #include <linux/iio/consumer.h> 14 #include <linux/interrupt.h> 15 #include <linux/module.h> 16 #include <linux/of.h> 17 #include <linux/of_device.h> 18 #include <linux/platform_device.h> 19 #include <linux/regmap.h> 20 #include <linux/thermal.h> 21 #include <asm-generic/unaligned.h> 22 23 #include "../thermal_hwmon.h" 24 25 /* 26 * Thermal monitoring block consists of 8 (ADC_TM5_NUM_CHANNELS) channels. Each 27 * channel is programmed to use one of ADC channels for voltage comparison. 28 * Voltages are programmed using ADC codes, so we have to convert temp to 29 * voltage and then to ADC code value. 30 * 31 * Configuration of TM channels must match configuration of corresponding ADC 32 * channels. 33 */ 34 35 #define ADC5_MAX_CHANNEL 0xc0 36 #define ADC_TM5_NUM_CHANNELS 8 37 38 #define ADC_TM5_STATUS_LOW 0x0a 39 40 #define ADC_TM5_STATUS_HIGH 0x0b 41 42 #define ADC_TM5_NUM_BTM 0x0f 43 44 #define ADC_TM5_ADC_DIG_PARAM 0x42 45 46 #define ADC_TM5_FAST_AVG_CTL (ADC_TM5_ADC_DIG_PARAM + 1) 47 #define ADC_TM5_FAST_AVG_EN BIT(7) 48 49 #define ADC_TM5_MEAS_INTERVAL_CTL (ADC_TM5_ADC_DIG_PARAM + 2) 50 #define ADC_TM5_TIMER1 3 /* 3.9ms */ 51 52 #define ADC_TM5_MEAS_INTERVAL_CTL2 (ADC_TM5_ADC_DIG_PARAM + 3) 53 #define ADC_TM5_MEAS_INTERVAL_CTL2_MASK 0xf0 54 #define ADC_TM5_TIMER2 10 /* 1 second */ 55 #define ADC_TM5_MEAS_INTERVAL_CTL3_MASK 0xf 56 #define ADC_TM5_TIMER3 4 /* 4 second */ 57 58 #define ADC_TM_EN_CTL1 0x46 59 #define ADC_TM_EN BIT(7) 60 #define ADC_TM_CONV_REQ 0x47 61 #define ADC_TM_CONV_REQ_EN BIT(7) 62 63 #define ADC_TM5_M_CHAN_BASE 0x60 64 65 #define ADC_TM5_M_ADC_CH_SEL_CTL(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 0) 66 #define ADC_TM5_M_LOW_THR0(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 1) 67 #define ADC_TM5_M_LOW_THR1(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 2) 68 #define ADC_TM5_M_HIGH_THR0(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 3) 69 #define ADC_TM5_M_HIGH_THR1(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 4) 70 #define ADC_TM5_M_MEAS_INTERVAL_CTL(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 5) 71 #define ADC_TM5_M_CTL(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 6) 72 #define ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK 0xf 73 #define ADC_TM5_M_CTL_CAL_SEL_MASK 0x30 74 #define ADC_TM5_M_CTL_CAL_VAL 0x40 75 #define ADC_TM5_M_EN(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 7) 76 #define ADC_TM5_M_MEAS_EN BIT(7) 77 #define ADC_TM5_M_HIGH_THR_INT_EN BIT(1) 78 #define ADC_TM5_M_LOW_THR_INT_EN BIT(0) 79 80 #define ADC_TM_GEN2_STATUS1 0x08 81 #define ADC_TM_GEN2_STATUS_LOW_SET 0x09 82 #define ADC_TM_GEN2_STATUS_LOW_CLR 0x0a 83 #define ADC_TM_GEN2_STATUS_HIGH_SET 0x0b 84 #define ADC_TM_GEN2_STATUS_HIGH_CLR 0x0c 85 86 #define ADC_TM_GEN2_CFG_HS_SET 0x0d 87 #define ADC_TM_GEN2_CFG_HS_FLAG BIT(0) 88 #define ADC_TM_GEN2_CFG_HS_CLR 0x0e 89 90 #define ADC_TM_GEN2_SID 0x40 91 92 #define ADC_TM_GEN2_CH_CTL 0x41 93 #define ADC_TM_GEN2_TM_CH_SEL GENMASK(7, 5) 94 #define ADC_TM_GEN2_MEAS_INT_SEL GENMASK(3, 2) 95 96 #define ADC_TM_GEN2_ADC_DIG_PARAM 0x42 97 #define ADC_TM_GEN2_CTL_CAL_SEL GENMASK(5, 4) 98 #define ADC_TM_GEN2_CTL_DEC_RATIO_MASK GENMASK(3, 2) 99 100 #define ADC_TM_GEN2_FAST_AVG_CTL 0x43 101 #define ADC_TM_GEN2_FAST_AVG_EN BIT(7) 102 103 #define ADC_TM_GEN2_ADC_CH_SEL_CTL 0x44 104 105 #define ADC_TM_GEN2_DELAY_CTL 0x45 106 #define ADC_TM_GEN2_HW_SETTLE_DELAY GENMASK(3, 0) 107 108 #define ADC_TM_GEN2_EN_CTL1 0x46 109 #define ADC_TM_GEN2_EN BIT(7) 110 111 #define ADC_TM_GEN2_CONV_REQ 0x47 112 #define ADC_TM_GEN2_CONV_REQ_EN BIT(7) 113 114 #define ADC_TM_GEN2_LOW_THR0 0x49 115 #define ADC_TM_GEN2_LOW_THR1 0x4a 116 #define ADC_TM_GEN2_HIGH_THR0 0x4b 117 #define ADC_TM_GEN2_HIGH_THR1 0x4c 118 #define ADC_TM_GEN2_LOWER_MASK(n) ((n) & GENMASK(7, 0)) 119 #define ADC_TM_GEN2_UPPER_MASK(n) (((n) & GENMASK(15, 8)) >> 8) 120 121 #define ADC_TM_GEN2_MEAS_IRQ_EN 0x4d 122 #define ADC_TM_GEN2_MEAS_EN BIT(7) 123 #define ADC_TM5_GEN2_HIGH_THR_INT_EN BIT(1) 124 #define ADC_TM5_GEN2_LOW_THR_INT_EN BIT(0) 125 126 #define ADC_TM_GEN2_MEAS_INT_LSB 0x50 127 #define ADC_TM_GEN2_MEAS_INT_MSB 0x51 128 #define ADC_TM_GEN2_MEAS_INT_MODE 0x52 129 130 #define ADC_TM_GEN2_Mn_DATA0(n) ((n * 2) + 0xa0) 131 #define ADC_TM_GEN2_Mn_DATA1(n) ((n * 2) + 0xa1) 132 #define ADC_TM_GEN2_DATA_SHIFT 8 133 134 enum adc5_timer_select { 135 ADC5_TIMER_SEL_1 = 0, 136 ADC5_TIMER_SEL_2, 137 ADC5_TIMER_SEL_3, 138 ADC5_TIMER_SEL_NONE, 139 }; 140 141 enum adc5_gen { 142 ADC_TM5, 143 ADC_TM_HC, 144 ADC_TM5_GEN2, 145 ADC_TM5_MAX 146 }; 147 148 enum adc_tm5_cal_method { 149 ADC_TM5_NO_CAL = 0, 150 ADC_TM5_RATIOMETRIC_CAL, 151 ADC_TM5_ABSOLUTE_CAL 152 }; 153 154 enum adc_tm_gen2_time_select { 155 MEAS_INT_50MS = 0, 156 MEAS_INT_100MS, 157 MEAS_INT_1S, 158 MEAS_INT_SET, 159 MEAS_INT_NONE, 160 }; 161 162 struct adc_tm5_chip; 163 struct adc_tm5_channel; 164 165 struct adc_tm5_data { 166 const u32 full_scale_code_volt; 167 unsigned int *decimation; 168 unsigned int *hw_settle; 169 int (*disable_channel)(struct adc_tm5_channel *channel); 170 int (*configure)(struct adc_tm5_channel *channel, int low, int high); 171 irqreturn_t (*isr)(int irq, void *data); 172 int (*init)(struct adc_tm5_chip *chip); 173 char *irq_name; 174 int gen; 175 }; 176 177 /** 178 * struct adc_tm5_channel - ADC Thermal Monitoring channel data. 179 * @channel: channel number. 180 * @adc_channel: corresponding ADC channel number. 181 * @cal_method: calibration method. 182 * @prescale: channel scaling performed on the input signal. 183 * @hw_settle_time: the time between AMUX being configured and the 184 * start of conversion. 185 * @decimation: sampling rate supported for the channel. 186 * @avg_samples: ability to provide single result from the ADC 187 * that is an average of multiple measurements. 188 * @high_thr_en: channel upper voltage threshold enable state. 189 * @low_thr_en: channel lower voltage threshold enable state. 190 * @meas_en: recurring measurement enable state 191 * @iio: IIO channel instance used by this channel. 192 * @chip: ADC TM chip instance. 193 * @tzd: thermal zone device used by this channel. 194 */ 195 struct adc_tm5_channel { 196 unsigned int channel; 197 unsigned int adc_channel; 198 enum adc_tm5_cal_method cal_method; 199 unsigned int prescale; 200 unsigned int hw_settle_time; 201 unsigned int decimation; /* For Gen2 ADC_TM */ 202 unsigned int avg_samples; /* For Gen2 ADC_TM */ 203 bool high_thr_en; /* For Gen2 ADC_TM */ 204 bool low_thr_en; /* For Gen2 ADC_TM */ 205 bool meas_en; /* For Gen2 ADC_TM */ 206 struct iio_channel *iio; 207 struct adc_tm5_chip *chip; 208 struct thermal_zone_device *tzd; 209 }; 210 211 /** 212 * struct adc_tm5_chip - ADC Thermal Monitoring properties 213 * @regmap: SPMI ADC5 Thermal Monitoring peripheral register map field. 214 * @dev: SPMI ADC5 device. 215 * @data: software configuration data. 216 * @channels: array of ADC TM channel data. 217 * @nchannels: amount of channels defined/allocated 218 * @decimation: sampling rate supported for the channel. 219 * Applies to all channels, used only on Gen1 ADC_TM. 220 * @avg_samples: ability to provide single result from the ADC 221 * that is an average of multiple measurements. Applies to all 222 * channels, used only on Gen1 ADC_TM. 223 * @base: base address of TM registers. 224 * @adc_mutex_lock: ADC_TM mutex lock, used only on Gen2 ADC_TM. 225 * It is used to ensure only one ADC channel configuration 226 * is done at a time using the shared set of configuration 227 * registers. 228 */ 229 struct adc_tm5_chip { 230 struct regmap *regmap; 231 struct device *dev; 232 const struct adc_tm5_data *data; 233 struct adc_tm5_channel *channels; 234 unsigned int nchannels; 235 unsigned int decimation; 236 unsigned int avg_samples; 237 u16 base; 238 struct mutex adc_mutex_lock; 239 }; 240 241 static int adc_tm5_read(struct adc_tm5_chip *adc_tm, u16 offset, u8 *data, int len) 242 { 243 return regmap_bulk_read(adc_tm->regmap, adc_tm->base + offset, data, len); 244 } 245 246 static int adc_tm5_write(struct adc_tm5_chip *adc_tm, u16 offset, u8 *data, int len) 247 { 248 return regmap_bulk_write(adc_tm->regmap, adc_tm->base + offset, data, len); 249 } 250 251 static int adc_tm5_reg_update(struct adc_tm5_chip *adc_tm, u16 offset, u8 mask, u8 val) 252 { 253 return regmap_write_bits(adc_tm->regmap, adc_tm->base + offset, mask, val); 254 } 255 256 static irqreturn_t adc_tm5_isr(int irq, void *data) 257 { 258 struct adc_tm5_chip *chip = data; 259 u8 status_low, status_high, ctl; 260 int ret, i; 261 262 ret = adc_tm5_read(chip, ADC_TM5_STATUS_LOW, &status_low, sizeof(status_low)); 263 if (unlikely(ret)) { 264 dev_err(chip->dev, "read status low failed: %d\n", ret); 265 return IRQ_HANDLED; 266 } 267 268 ret = adc_tm5_read(chip, ADC_TM5_STATUS_HIGH, &status_high, sizeof(status_high)); 269 if (unlikely(ret)) { 270 dev_err(chip->dev, "read status high failed: %d\n", ret); 271 return IRQ_HANDLED; 272 } 273 274 for (i = 0; i < chip->nchannels; i++) { 275 bool upper_set = false, lower_set = false; 276 unsigned int ch = chip->channels[i].channel; 277 278 /* No TZD, we warned at the boot time */ 279 if (!chip->channels[i].tzd) 280 continue; 281 282 ret = adc_tm5_read(chip, ADC_TM5_M_EN(ch), &ctl, sizeof(ctl)); 283 if (unlikely(ret)) { 284 dev_err(chip->dev, "ctl read failed: %d, channel %d\n", ret, i); 285 continue; 286 } 287 288 if (!(ctl & ADC_TM5_M_MEAS_EN)) 289 continue; 290 291 lower_set = (status_low & BIT(ch)) && 292 (ctl & ADC_TM5_M_LOW_THR_INT_EN); 293 294 upper_set = (status_high & BIT(ch)) && 295 (ctl & ADC_TM5_M_HIGH_THR_INT_EN); 296 297 if (upper_set || lower_set) 298 thermal_zone_device_update(chip->channels[i].tzd, 299 THERMAL_EVENT_UNSPECIFIED); 300 } 301 302 return IRQ_HANDLED; 303 } 304 305 static irqreturn_t adc_tm5_gen2_isr(int irq, void *data) 306 { 307 struct adc_tm5_chip *chip = data; 308 u8 status_low, status_high; 309 int ret, i; 310 311 ret = adc_tm5_read(chip, ADC_TM_GEN2_STATUS_LOW_CLR, &status_low, sizeof(status_low)); 312 if (ret) { 313 dev_err(chip->dev, "read status_low failed: %d\n", ret); 314 return IRQ_HANDLED; 315 } 316 317 ret = adc_tm5_read(chip, ADC_TM_GEN2_STATUS_HIGH_CLR, &status_high, sizeof(status_high)); 318 if (ret) { 319 dev_err(chip->dev, "read status_high failed: %d\n", ret); 320 return IRQ_HANDLED; 321 } 322 323 ret = adc_tm5_write(chip, ADC_TM_GEN2_STATUS_LOW_CLR, &status_low, sizeof(status_low)); 324 if (ret < 0) { 325 dev_err(chip->dev, "clear status low failed with %d\n", ret); 326 return IRQ_HANDLED; 327 } 328 329 ret = adc_tm5_write(chip, ADC_TM_GEN2_STATUS_HIGH_CLR, &status_high, sizeof(status_high)); 330 if (ret < 0) { 331 dev_err(chip->dev, "clear status high failed with %d\n", ret); 332 return IRQ_HANDLED; 333 } 334 335 for (i = 0; i < chip->nchannels; i++) { 336 bool upper_set = false, lower_set = false; 337 unsigned int ch = chip->channels[i].channel; 338 339 /* No TZD, we warned at the boot time */ 340 if (!chip->channels[i].tzd) 341 continue; 342 343 if (!chip->channels[i].meas_en) 344 continue; 345 346 lower_set = (status_low & BIT(ch)) && 347 (chip->channels[i].low_thr_en); 348 349 upper_set = (status_high & BIT(ch)) && 350 (chip->channels[i].high_thr_en); 351 352 if (upper_set || lower_set) 353 thermal_zone_device_update(chip->channels[i].tzd, 354 THERMAL_EVENT_UNSPECIFIED); 355 } 356 357 return IRQ_HANDLED; 358 } 359 360 static int adc_tm5_get_temp(struct thermal_zone_device *tz, int *temp) 361 { 362 struct adc_tm5_channel *channel = tz->devdata; 363 int ret; 364 365 if (!channel || !channel->iio) 366 return -EINVAL; 367 368 ret = iio_read_channel_processed(channel->iio, temp); 369 if (ret < 0) 370 return ret; 371 372 if (ret != IIO_VAL_INT) 373 return -EINVAL; 374 375 return 0; 376 } 377 378 static int adc_tm5_disable_channel(struct adc_tm5_channel *channel) 379 { 380 struct adc_tm5_chip *chip = channel->chip; 381 unsigned int reg = ADC_TM5_M_EN(channel->channel); 382 383 return adc_tm5_reg_update(chip, reg, 384 ADC_TM5_M_MEAS_EN | 385 ADC_TM5_M_HIGH_THR_INT_EN | 386 ADC_TM5_M_LOW_THR_INT_EN, 387 0); 388 } 389 390 #define ADC_TM_GEN2_POLL_DELAY_MIN_US 100 391 #define ADC_TM_GEN2_POLL_DELAY_MAX_US 110 392 #define ADC_TM_GEN2_POLL_RETRY_COUNT 3 393 394 static int32_t adc_tm5_gen2_conv_req(struct adc_tm5_chip *chip) 395 { 396 int ret; 397 u8 data; 398 unsigned int count; 399 400 data = ADC_TM_GEN2_EN; 401 ret = adc_tm5_write(chip, ADC_TM_GEN2_EN_CTL1, &data, 1); 402 if (ret < 0) { 403 dev_err(chip->dev, "adc-tm enable failed with %d\n", ret); 404 return ret; 405 } 406 407 data = ADC_TM_GEN2_CFG_HS_FLAG; 408 ret = adc_tm5_write(chip, ADC_TM_GEN2_CFG_HS_SET, &data, 1); 409 if (ret < 0) { 410 dev_err(chip->dev, "adc-tm handshake failed with %d\n", ret); 411 return ret; 412 } 413 414 data = ADC_TM_GEN2_CONV_REQ_EN; 415 ret = adc_tm5_write(chip, ADC_TM_GEN2_CONV_REQ, &data, 1); 416 if (ret < 0) { 417 dev_err(chip->dev, "adc-tm request conversion failed with %d\n", ret); 418 return ret; 419 } 420 421 /* 422 * SW sets a handshake bit and waits for PBS to clear it 423 * before the next conversion request can be queued. 424 */ 425 426 for (count = 0; count < ADC_TM_GEN2_POLL_RETRY_COUNT; count++) { 427 ret = adc_tm5_read(chip, ADC_TM_GEN2_CFG_HS_SET, &data, sizeof(data)); 428 if (ret < 0) { 429 dev_err(chip->dev, "adc-tm read failed with %d\n", ret); 430 return ret; 431 } 432 433 if (!(data & ADC_TM_GEN2_CFG_HS_FLAG)) 434 return ret; 435 usleep_range(ADC_TM_GEN2_POLL_DELAY_MIN_US, 436 ADC_TM_GEN2_POLL_DELAY_MAX_US); 437 } 438 439 dev_err(chip->dev, "adc-tm conversion request handshake timed out\n"); 440 441 return -ETIMEDOUT; 442 } 443 444 static int adc_tm5_gen2_disable_channel(struct adc_tm5_channel *channel) 445 { 446 struct adc_tm5_chip *chip = channel->chip; 447 int ret; 448 u8 val; 449 450 mutex_lock(&chip->adc_mutex_lock); 451 452 channel->meas_en = false; 453 channel->high_thr_en = false; 454 channel->low_thr_en = false; 455 456 ret = adc_tm5_read(chip, ADC_TM_GEN2_CH_CTL, &val, sizeof(val)); 457 if (ret < 0) { 458 dev_err(chip->dev, "adc-tm block read failed with %d\n", ret); 459 goto disable_fail; 460 } 461 462 val &= ~ADC_TM_GEN2_TM_CH_SEL; 463 val |= FIELD_PREP(ADC_TM_GEN2_TM_CH_SEL, channel->channel); 464 465 ret = adc_tm5_write(chip, ADC_TM_GEN2_CH_CTL, &val, 1); 466 if (ret < 0) { 467 dev_err(chip->dev, "adc-tm channel disable failed with %d\n", ret); 468 goto disable_fail; 469 } 470 471 val = 0; 472 ret = adc_tm5_write(chip, ADC_TM_GEN2_MEAS_IRQ_EN, &val, 1); 473 if (ret < 0) { 474 dev_err(chip->dev, "adc-tm interrupt disable failed with %d\n", ret); 475 goto disable_fail; 476 } 477 478 479 ret = adc_tm5_gen2_conv_req(channel->chip); 480 if (ret < 0) 481 dev_err(chip->dev, "adc-tm channel configure failed with %d\n", ret); 482 483 disable_fail: 484 mutex_unlock(&chip->adc_mutex_lock); 485 return ret; 486 } 487 488 static int adc_tm5_enable(struct adc_tm5_chip *chip) 489 { 490 int ret; 491 u8 data; 492 493 data = ADC_TM_EN; 494 ret = adc_tm5_write(chip, ADC_TM_EN_CTL1, &data, sizeof(data)); 495 if (ret < 0) { 496 dev_err(chip->dev, "adc-tm enable failed\n"); 497 return ret; 498 } 499 500 data = ADC_TM_CONV_REQ_EN; 501 ret = adc_tm5_write(chip, ADC_TM_CONV_REQ, &data, sizeof(data)); 502 if (ret < 0) { 503 dev_err(chip->dev, "adc-tm request conversion failed\n"); 504 return ret; 505 } 506 507 return 0; 508 } 509 510 static int adc_tm5_configure(struct adc_tm5_channel *channel, int low, int high) 511 { 512 struct adc_tm5_chip *chip = channel->chip; 513 u8 buf[8]; 514 u16 reg = ADC_TM5_M_ADC_CH_SEL_CTL(channel->channel); 515 int ret; 516 517 ret = adc_tm5_read(chip, reg, buf, sizeof(buf)); 518 if (ret) { 519 dev_err(chip->dev, "channel %d params read failed: %d\n", channel->channel, ret); 520 return ret; 521 } 522 523 buf[0] = channel->adc_channel; 524 525 /* High temperature corresponds to low voltage threshold */ 526 if (high != INT_MAX) { 527 u16 adc_code = qcom_adc_tm5_temp_volt_scale(channel->prescale, 528 chip->data->full_scale_code_volt, high); 529 530 put_unaligned_le16(adc_code, &buf[1]); 531 buf[7] |= ADC_TM5_M_LOW_THR_INT_EN; 532 } else { 533 buf[7] &= ~ADC_TM5_M_LOW_THR_INT_EN; 534 } 535 536 /* Low temperature corresponds to high voltage threshold */ 537 if (low != -INT_MAX) { 538 u16 adc_code = qcom_adc_tm5_temp_volt_scale(channel->prescale, 539 chip->data->full_scale_code_volt, low); 540 541 put_unaligned_le16(adc_code, &buf[3]); 542 buf[7] |= ADC_TM5_M_HIGH_THR_INT_EN; 543 } else { 544 buf[7] &= ~ADC_TM5_M_HIGH_THR_INT_EN; 545 } 546 547 buf[5] = ADC5_TIMER_SEL_2; 548 549 /* Set calibration select, hw_settle delay */ 550 buf[6] &= ~ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK; 551 buf[6] |= FIELD_PREP(ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK, channel->hw_settle_time); 552 buf[6] &= ~ADC_TM5_M_CTL_CAL_SEL_MASK; 553 buf[6] |= FIELD_PREP(ADC_TM5_M_CTL_CAL_SEL_MASK, channel->cal_method); 554 555 buf[7] |= ADC_TM5_M_MEAS_EN; 556 557 ret = adc_tm5_write(chip, reg, buf, sizeof(buf)); 558 if (ret) { 559 dev_err(chip->dev, "channel %d params write failed: %d\n", channel->channel, ret); 560 return ret; 561 } 562 563 return adc_tm5_enable(chip); 564 } 565 566 static int adc_tm5_gen2_configure(struct adc_tm5_channel *channel, int low, int high) 567 { 568 struct adc_tm5_chip *chip = channel->chip; 569 int ret; 570 u8 buf[14]; 571 u16 adc_code; 572 573 mutex_lock(&chip->adc_mutex_lock); 574 575 channel->meas_en = true; 576 577 ret = adc_tm5_read(chip, ADC_TM_GEN2_SID, buf, sizeof(buf)); 578 if (ret < 0) { 579 dev_err(chip->dev, "adc-tm block read failed with %d\n", ret); 580 goto config_fail; 581 } 582 583 /* Set SID from virtual channel number */ 584 buf[0] = channel->adc_channel >> 8; 585 586 /* Set TM channel number used and measurement interval */ 587 buf[1] &= ~ADC_TM_GEN2_TM_CH_SEL; 588 buf[1] |= FIELD_PREP(ADC_TM_GEN2_TM_CH_SEL, channel->channel); 589 buf[1] &= ~ADC_TM_GEN2_MEAS_INT_SEL; 590 buf[1] |= FIELD_PREP(ADC_TM_GEN2_MEAS_INT_SEL, MEAS_INT_1S); 591 592 buf[2] &= ~ADC_TM_GEN2_CTL_DEC_RATIO_MASK; 593 buf[2] |= FIELD_PREP(ADC_TM_GEN2_CTL_DEC_RATIO_MASK, channel->decimation); 594 buf[2] &= ~ADC_TM_GEN2_CTL_CAL_SEL; 595 buf[2] |= FIELD_PREP(ADC_TM_GEN2_CTL_CAL_SEL, channel->cal_method); 596 597 buf[3] = channel->avg_samples | ADC_TM_GEN2_FAST_AVG_EN; 598 599 buf[4] = channel->adc_channel & 0xff; 600 601 buf[5] = channel->hw_settle_time & ADC_TM_GEN2_HW_SETTLE_DELAY; 602 603 /* High temperature corresponds to low voltage threshold */ 604 if (high != INT_MAX) { 605 channel->low_thr_en = true; 606 adc_code = qcom_adc_tm5_gen2_temp_res_scale(high); 607 put_unaligned_le16(adc_code, &buf[9]); 608 } else { 609 channel->low_thr_en = false; 610 } 611 612 /* Low temperature corresponds to high voltage threshold */ 613 if (low != -INT_MAX) { 614 channel->high_thr_en = true; 615 adc_code = qcom_adc_tm5_gen2_temp_res_scale(low); 616 put_unaligned_le16(adc_code, &buf[11]); 617 } else { 618 channel->high_thr_en = false; 619 } 620 621 buf[13] = ADC_TM_GEN2_MEAS_EN; 622 if (channel->high_thr_en) 623 buf[13] |= ADC_TM5_GEN2_HIGH_THR_INT_EN; 624 if (channel->low_thr_en) 625 buf[13] |= ADC_TM5_GEN2_LOW_THR_INT_EN; 626 627 ret = adc_tm5_write(chip, ADC_TM_GEN2_SID, buf, sizeof(buf)); 628 if (ret) { 629 dev_err(chip->dev, "channel %d params write failed: %d\n", channel->channel, ret); 630 goto config_fail; 631 } 632 633 ret = adc_tm5_gen2_conv_req(channel->chip); 634 if (ret < 0) 635 dev_err(chip->dev, "adc-tm channel configure failed with %d\n", ret); 636 637 config_fail: 638 mutex_unlock(&chip->adc_mutex_lock); 639 return ret; 640 } 641 642 static int adc_tm5_set_trips(struct thermal_zone_device *tz, int low, int high) 643 { 644 struct adc_tm5_channel *channel = tz->devdata; 645 struct adc_tm5_chip *chip; 646 int ret; 647 648 if (!channel) 649 return -EINVAL; 650 651 chip = channel->chip; 652 dev_dbg(chip->dev, "%d:low(mdegC):%d, high(mdegC):%d\n", 653 channel->channel, low, high); 654 655 if (high == INT_MAX && low <= -INT_MAX) 656 ret = chip->data->disable_channel(channel); 657 else 658 ret = chip->data->configure(channel, low, high); 659 660 return ret; 661 } 662 663 static const struct thermal_zone_device_ops adc_tm5_thermal_ops = { 664 .get_temp = adc_tm5_get_temp, 665 .set_trips = adc_tm5_set_trips, 666 }; 667 668 static int adc_tm5_register_tzd(struct adc_tm5_chip *adc_tm) 669 { 670 unsigned int i; 671 struct thermal_zone_device *tzd; 672 673 for (i = 0; i < adc_tm->nchannels; i++) { 674 adc_tm->channels[i].chip = adc_tm; 675 tzd = devm_thermal_of_zone_register(adc_tm->dev, 676 adc_tm->channels[i].channel, 677 &adc_tm->channels[i], 678 &adc_tm5_thermal_ops); 679 if (IS_ERR(tzd)) { 680 if (PTR_ERR(tzd) == -ENODEV) { 681 dev_dbg(adc_tm->dev, "thermal sensor on channel %d is not used\n", 682 adc_tm->channels[i].channel); 683 continue; 684 } 685 686 dev_err(adc_tm->dev, "Error registering TZ zone for channel %d: %ld\n", 687 adc_tm->channels[i].channel, PTR_ERR(tzd)); 688 return PTR_ERR(tzd); 689 } 690 adc_tm->channels[i].tzd = tzd; 691 if (devm_thermal_add_hwmon_sysfs(tzd)) 692 dev_warn(adc_tm->dev, 693 "Failed to add hwmon sysfs attributes\n"); 694 } 695 696 return 0; 697 } 698 699 static int adc_tm_hc_init(struct adc_tm5_chip *chip) 700 { 701 unsigned int i; 702 u8 buf[2]; 703 int ret; 704 705 for (i = 0; i < chip->nchannels; i++) { 706 if (chip->channels[i].channel >= ADC_TM5_NUM_CHANNELS) { 707 dev_err(chip->dev, "Invalid channel %d\n", chip->channels[i].channel); 708 return -EINVAL; 709 } 710 } 711 712 buf[0] = chip->decimation; 713 buf[1] = chip->avg_samples | ADC_TM5_FAST_AVG_EN; 714 715 ret = adc_tm5_write(chip, ADC_TM5_ADC_DIG_PARAM, buf, sizeof(buf)); 716 if (ret) 717 dev_err(chip->dev, "block write failed: %d\n", ret); 718 719 return ret; 720 } 721 722 static int adc_tm5_init(struct adc_tm5_chip *chip) 723 { 724 u8 buf[4], channels_available; 725 int ret; 726 unsigned int i; 727 728 ret = adc_tm5_read(chip, ADC_TM5_NUM_BTM, 729 &channels_available, sizeof(channels_available)); 730 if (ret) { 731 dev_err(chip->dev, "read failed for BTM channels\n"); 732 return ret; 733 } 734 735 for (i = 0; i < chip->nchannels; i++) { 736 if (chip->channels[i].channel >= channels_available) { 737 dev_err(chip->dev, "Invalid channel %d\n", chip->channels[i].channel); 738 return -EINVAL; 739 } 740 } 741 742 buf[0] = chip->decimation; 743 buf[1] = chip->avg_samples | ADC_TM5_FAST_AVG_EN; 744 buf[2] = ADC_TM5_TIMER1; 745 buf[3] = FIELD_PREP(ADC_TM5_MEAS_INTERVAL_CTL2_MASK, ADC_TM5_TIMER2) | 746 FIELD_PREP(ADC_TM5_MEAS_INTERVAL_CTL3_MASK, ADC_TM5_TIMER3); 747 748 ret = adc_tm5_write(chip, ADC_TM5_ADC_DIG_PARAM, buf, sizeof(buf)); 749 if (ret) { 750 dev_err(chip->dev, "block write failed: %d\n", ret); 751 return ret; 752 } 753 754 return ret; 755 } 756 757 static int adc_tm5_gen2_init(struct adc_tm5_chip *chip) 758 { 759 u8 channels_available; 760 int ret; 761 unsigned int i; 762 763 ret = adc_tm5_read(chip, ADC_TM5_NUM_BTM, 764 &channels_available, sizeof(channels_available)); 765 if (ret) { 766 dev_err(chip->dev, "read failed for BTM channels\n"); 767 return ret; 768 } 769 770 for (i = 0; i < chip->nchannels; i++) { 771 if (chip->channels[i].channel >= channels_available) { 772 dev_err(chip->dev, "Invalid channel %d\n", chip->channels[i].channel); 773 return -EINVAL; 774 } 775 } 776 777 mutex_init(&chip->adc_mutex_lock); 778 779 return ret; 780 } 781 782 static int adc_tm5_get_dt_channel_data(struct adc_tm5_chip *adc_tm, 783 struct adc_tm5_channel *channel, 784 struct device_node *node) 785 { 786 const char *name = node->name; 787 u32 chan, value, adc_channel, varr[2]; 788 int ret; 789 struct device *dev = adc_tm->dev; 790 struct of_phandle_args args; 791 792 ret = of_property_read_u32(node, "reg", &chan); 793 if (ret) { 794 dev_err(dev, "%s: invalid channel number %d\n", name, ret); 795 return ret; 796 } 797 798 if (chan >= ADC_TM5_NUM_CHANNELS) { 799 dev_err(dev, "%s: channel number too big: %d\n", name, chan); 800 return -EINVAL; 801 } 802 803 channel->channel = chan; 804 805 /* 806 * We are tied to PMIC's ADC controller, which always use single 807 * argument for channel number. So don't bother parsing 808 * #io-channel-cells, just enforce cell_count = 1. 809 */ 810 ret = of_parse_phandle_with_fixed_args(node, "io-channels", 1, 0, &args); 811 if (ret < 0) { 812 dev_err(dev, "%s: error parsing ADC channel number %d: %d\n", name, chan, ret); 813 return ret; 814 } 815 of_node_put(args.np); 816 817 if (args.args_count != 1) { 818 dev_err(dev, "%s: invalid args count for ADC channel %d\n", name, chan); 819 return -EINVAL; 820 } 821 822 adc_channel = args.args[0]; 823 if (adc_tm->data->gen == ADC_TM5_GEN2) 824 adc_channel &= 0xff; 825 826 if (adc_channel >= ADC5_MAX_CHANNEL) { 827 dev_err(dev, "%s: invalid ADC channel number %d\n", name, chan); 828 return -EINVAL; 829 } 830 channel->adc_channel = args.args[0]; 831 832 channel->iio = devm_fwnode_iio_channel_get_by_name(adc_tm->dev, 833 of_fwnode_handle(node), NULL); 834 if (IS_ERR(channel->iio)) { 835 ret = PTR_ERR(channel->iio); 836 if (ret != -EPROBE_DEFER) 837 dev_err(dev, "%s: error getting channel: %d\n", name, ret); 838 return ret; 839 } 840 841 ret = of_property_read_u32_array(node, "qcom,pre-scaling", varr, 2); 842 if (!ret) { 843 ret = qcom_adc5_prescaling_from_dt(varr[0], varr[1]); 844 if (ret < 0) { 845 dev_err(dev, "%s: invalid pre-scaling <%d %d>\n", 846 name, varr[0], varr[1]); 847 return ret; 848 } 849 channel->prescale = ret; 850 } else { 851 /* 1:1 prescale is index 0 */ 852 channel->prescale = 0; 853 } 854 855 ret = of_property_read_u32(node, "qcom,hw-settle-time-us", &value); 856 if (!ret) { 857 ret = qcom_adc5_hw_settle_time_from_dt(value, adc_tm->data->hw_settle); 858 if (ret < 0) { 859 dev_err(dev, "%s invalid hw-settle-time-us %d us\n", 860 name, value); 861 return ret; 862 } 863 channel->hw_settle_time = ret; 864 } else { 865 channel->hw_settle_time = VADC_DEF_HW_SETTLE_TIME; 866 } 867 868 if (of_property_read_bool(node, "qcom,ratiometric")) 869 channel->cal_method = ADC_TM5_RATIOMETRIC_CAL; 870 else 871 channel->cal_method = ADC_TM5_ABSOLUTE_CAL; 872 873 if (adc_tm->data->gen == ADC_TM5_GEN2) { 874 ret = of_property_read_u32(node, "qcom,decimation", &value); 875 if (!ret) { 876 ret = qcom_adc5_decimation_from_dt(value, adc_tm->data->decimation); 877 if (ret < 0) { 878 dev_err(dev, "invalid decimation %d\n", value); 879 return ret; 880 } 881 channel->decimation = ret; 882 } else { 883 channel->decimation = ADC5_DECIMATION_DEFAULT; 884 } 885 886 ret = of_property_read_u32(node, "qcom,avg-samples", &value); 887 if (!ret) { 888 ret = qcom_adc5_avg_samples_from_dt(value); 889 if (ret < 0) { 890 dev_err(dev, "invalid avg-samples %d\n", value); 891 return ret; 892 } 893 channel->avg_samples = ret; 894 } else { 895 channel->avg_samples = VADC_DEF_AVG_SAMPLES; 896 } 897 } 898 899 return 0; 900 } 901 902 static const struct adc_tm5_data adc_tm5_data_pmic = { 903 .full_scale_code_volt = 0x70e4, 904 .decimation = (unsigned int []) { 250, 420, 840 }, 905 .hw_settle = (unsigned int []) { 15, 100, 200, 300, 400, 500, 600, 700, 906 1000, 2000, 4000, 8000, 16000, 32000, 907 64000, 128000 }, 908 .disable_channel = adc_tm5_disable_channel, 909 .configure = adc_tm5_configure, 910 .isr = adc_tm5_isr, 911 .init = adc_tm5_init, 912 .irq_name = "pm-adc-tm5", 913 .gen = ADC_TM5, 914 }; 915 916 static const struct adc_tm5_data adc_tm_hc_data_pmic = { 917 .full_scale_code_volt = 0x70e4, 918 .decimation = (unsigned int []) { 256, 512, 1024 }, 919 .hw_settle = (unsigned int []) { 0, 100, 200, 300, 400, 500, 600, 700, 920 1000, 2000, 4000, 6000, 8000, 10000 }, 921 .disable_channel = adc_tm5_disable_channel, 922 .configure = adc_tm5_configure, 923 .isr = adc_tm5_isr, 924 .init = adc_tm_hc_init, 925 .irq_name = "pm-adc-tm5", 926 .gen = ADC_TM_HC, 927 }; 928 929 static const struct adc_tm5_data adc_tm5_gen2_data_pmic = { 930 .full_scale_code_volt = 0x70e4, 931 .decimation = (unsigned int []) { 85, 340, 1360 }, 932 .hw_settle = (unsigned int []) { 15, 100, 200, 300, 400, 500, 600, 700, 933 1000, 2000, 4000, 8000, 16000, 32000, 934 64000, 128000 }, 935 .disable_channel = adc_tm5_gen2_disable_channel, 936 .configure = adc_tm5_gen2_configure, 937 .isr = adc_tm5_gen2_isr, 938 .init = adc_tm5_gen2_init, 939 .irq_name = "pm-adc-tm5-gen2", 940 .gen = ADC_TM5_GEN2, 941 }; 942 943 static int adc_tm5_get_dt_data(struct adc_tm5_chip *adc_tm, struct device_node *node) 944 { 945 struct adc_tm5_channel *channels; 946 struct device_node *child; 947 u32 value; 948 int ret; 949 struct device *dev = adc_tm->dev; 950 951 adc_tm->nchannels = of_get_available_child_count(node); 952 if (!adc_tm->nchannels) 953 return -EINVAL; 954 955 adc_tm->channels = devm_kcalloc(dev, adc_tm->nchannels, 956 sizeof(*adc_tm->channels), GFP_KERNEL); 957 if (!adc_tm->channels) 958 return -ENOMEM; 959 960 channels = adc_tm->channels; 961 962 adc_tm->data = of_device_get_match_data(dev); 963 if (!adc_tm->data) 964 adc_tm->data = &adc_tm5_data_pmic; 965 966 ret = of_property_read_u32(node, "qcom,decimation", &value); 967 if (!ret) { 968 ret = qcom_adc5_decimation_from_dt(value, adc_tm->data->decimation); 969 if (ret < 0) { 970 dev_err(dev, "invalid decimation %d\n", value); 971 return ret; 972 } 973 adc_tm->decimation = ret; 974 } else { 975 adc_tm->decimation = ADC5_DECIMATION_DEFAULT; 976 } 977 978 ret = of_property_read_u32(node, "qcom,avg-samples", &value); 979 if (!ret) { 980 ret = qcom_adc5_avg_samples_from_dt(value); 981 if (ret < 0) { 982 dev_err(dev, "invalid avg-samples %d\n", value); 983 return ret; 984 } 985 adc_tm->avg_samples = ret; 986 } else { 987 adc_tm->avg_samples = VADC_DEF_AVG_SAMPLES; 988 } 989 990 for_each_available_child_of_node(node, child) { 991 ret = adc_tm5_get_dt_channel_data(adc_tm, channels, child); 992 if (ret) { 993 of_node_put(child); 994 return ret; 995 } 996 997 channels++; 998 } 999 1000 return 0; 1001 } 1002 1003 static int adc_tm5_probe(struct platform_device *pdev) 1004 { 1005 struct device_node *node = pdev->dev.of_node; 1006 struct device *dev = &pdev->dev; 1007 struct adc_tm5_chip *adc_tm; 1008 struct regmap *regmap; 1009 int ret, irq; 1010 u32 reg; 1011 1012 regmap = dev_get_regmap(dev->parent, NULL); 1013 if (!regmap) 1014 return -ENODEV; 1015 1016 ret = of_property_read_u32(node, "reg", ®); 1017 if (ret) 1018 return ret; 1019 1020 adc_tm = devm_kzalloc(&pdev->dev, sizeof(*adc_tm), GFP_KERNEL); 1021 if (!adc_tm) 1022 return -ENOMEM; 1023 1024 adc_tm->regmap = regmap; 1025 adc_tm->dev = dev; 1026 adc_tm->base = reg; 1027 1028 irq = platform_get_irq(pdev, 0); 1029 if (irq < 0) 1030 return irq; 1031 1032 ret = adc_tm5_get_dt_data(adc_tm, node); 1033 if (ret) 1034 return dev_err_probe(dev, ret, "get dt data failed\n"); 1035 1036 ret = adc_tm->data->init(adc_tm); 1037 if (ret) { 1038 dev_err(dev, "adc-tm init failed\n"); 1039 return ret; 1040 } 1041 1042 ret = adc_tm5_register_tzd(adc_tm); 1043 if (ret) { 1044 dev_err(dev, "tzd register failed\n"); 1045 return ret; 1046 } 1047 1048 return devm_request_threaded_irq(dev, irq, NULL, adc_tm->data->isr, 1049 IRQF_ONESHOT, adc_tm->data->irq_name, adc_tm); 1050 } 1051 1052 static const struct of_device_id adc_tm5_match_table[] = { 1053 { 1054 .compatible = "qcom,spmi-adc-tm5", 1055 .data = &adc_tm5_data_pmic, 1056 }, 1057 { 1058 .compatible = "qcom,spmi-adc-tm-hc", 1059 .data = &adc_tm_hc_data_pmic, 1060 }, 1061 { 1062 .compatible = "qcom,spmi-adc-tm5-gen2", 1063 .data = &adc_tm5_gen2_data_pmic, 1064 }, 1065 { } 1066 }; 1067 MODULE_DEVICE_TABLE(of, adc_tm5_match_table); 1068 1069 static struct platform_driver adc_tm5_driver = { 1070 .driver = { 1071 .name = "qcom-spmi-adc-tm5", 1072 .of_match_table = adc_tm5_match_table, 1073 }, 1074 .probe = adc_tm5_probe, 1075 }; 1076 module_platform_driver(adc_tm5_driver); 1077 1078 MODULE_DESCRIPTION("SPMI PMIC Thermal Monitor ADC driver"); 1079 MODULE_LICENSE("GPL v2"); 1080