1 /* 2 * Xilinx SPI controller driver (master mode only) 3 * 4 * Author: MontaVista Software, Inc. 5 * source@mvista.com 6 * 7 * Copyright (c) 2010 Secret Lab Technologies, Ltd. 8 * Copyright (c) 2009 Intel Corporation 9 * 2002-2007 (c) MontaVista Software, Inc. 10 11 * This program is free software; you can redistribute it and/or modify 12 * it under the terms of the GNU General Public License version 2 as 13 * published by the Free Software Foundation. 14 */ 15 16 #include <linux/module.h> 17 #include <linux/interrupt.h> 18 #include <linux/of.h> 19 #include <linux/platform_device.h> 20 #include <linux/spi/spi.h> 21 #include <linux/spi/spi_bitbang.h> 22 #include <linux/spi/xilinx_spi.h> 23 #include <linux/io.h> 24 25 #define XILINX_SPI_NAME "xilinx_spi" 26 27 /* Register definitions as per "OPB Serial Peripheral Interface (SPI) (v1.00e) 28 * Product Specification", DS464 29 */ 30 #define XSPI_CR_OFFSET 0x60 /* Control Register */ 31 32 #define XSPI_CR_LOOP 0x01 33 #define XSPI_CR_ENABLE 0x02 34 #define XSPI_CR_MASTER_MODE 0x04 35 #define XSPI_CR_CPOL 0x08 36 #define XSPI_CR_CPHA 0x10 37 #define XSPI_CR_MODE_MASK (XSPI_CR_CPHA | XSPI_CR_CPOL) 38 #define XSPI_CR_TXFIFO_RESET 0x20 39 #define XSPI_CR_RXFIFO_RESET 0x40 40 #define XSPI_CR_MANUAL_SSELECT 0x80 41 #define XSPI_CR_TRANS_INHIBIT 0x100 42 #define XSPI_CR_LSB_FIRST 0x200 43 44 #define XSPI_SR_OFFSET 0x64 /* Status Register */ 45 46 #define XSPI_SR_RX_EMPTY_MASK 0x01 /* Receive FIFO is empty */ 47 #define XSPI_SR_RX_FULL_MASK 0x02 /* Receive FIFO is full */ 48 #define XSPI_SR_TX_EMPTY_MASK 0x04 /* Transmit FIFO is empty */ 49 #define XSPI_SR_TX_FULL_MASK 0x08 /* Transmit FIFO is full */ 50 #define XSPI_SR_MODE_FAULT_MASK 0x10 /* Mode fault error */ 51 52 #define XSPI_TXD_OFFSET 0x68 /* Data Transmit Register */ 53 #define XSPI_RXD_OFFSET 0x6c /* Data Receive Register */ 54 55 #define XSPI_SSR_OFFSET 0x70 /* 32-bit Slave Select Register */ 56 57 /* Register definitions as per "OPB IPIF (v3.01c) Product Specification", DS414 58 * IPIF registers are 32 bit 59 */ 60 #define XIPIF_V123B_DGIER_OFFSET 0x1c /* IPIF global int enable reg */ 61 #define XIPIF_V123B_GINTR_ENABLE 0x80000000 62 63 #define XIPIF_V123B_IISR_OFFSET 0x20 /* IPIF interrupt status reg */ 64 #define XIPIF_V123B_IIER_OFFSET 0x28 /* IPIF interrupt enable reg */ 65 66 #define XSPI_INTR_MODE_FAULT 0x01 /* Mode fault error */ 67 #define XSPI_INTR_SLAVE_MODE_FAULT 0x02 /* Selected as slave while 68 * disabled */ 69 #define XSPI_INTR_TX_EMPTY 0x04 /* TxFIFO is empty */ 70 #define XSPI_INTR_TX_UNDERRUN 0x08 /* TxFIFO was underrun */ 71 #define XSPI_INTR_RX_FULL 0x10 /* RxFIFO is full */ 72 #define XSPI_INTR_RX_OVERRUN 0x20 /* RxFIFO was overrun */ 73 #define XSPI_INTR_TX_HALF_EMPTY 0x40 /* TxFIFO is half empty */ 74 75 #define XIPIF_V123B_RESETR_OFFSET 0x40 /* IPIF reset register */ 76 #define XIPIF_V123B_RESET_MASK 0x0a /* the value to write */ 77 78 struct xilinx_spi { 79 /* bitbang has to be first */ 80 struct spi_bitbang bitbang; 81 struct completion done; 82 void __iomem *regs; /* virt. address of the control registers */ 83 84 int irq; 85 86 u8 *rx_ptr; /* pointer in the Tx buffer */ 87 const u8 *tx_ptr; /* pointer in the Rx buffer */ 88 int remaining_bytes; /* the number of bytes left to transfer */ 89 u8 bits_per_word; 90 unsigned int (*read_fn)(void __iomem *); 91 void (*write_fn)(u32, void __iomem *); 92 void (*tx_fn)(struct xilinx_spi *); 93 void (*rx_fn)(struct xilinx_spi *); 94 }; 95 96 static void xspi_write32(u32 val, void __iomem *addr) 97 { 98 iowrite32(val, addr); 99 } 100 101 static unsigned int xspi_read32(void __iomem *addr) 102 { 103 return ioread32(addr); 104 } 105 106 static void xspi_write32_be(u32 val, void __iomem *addr) 107 { 108 iowrite32be(val, addr); 109 } 110 111 static unsigned int xspi_read32_be(void __iomem *addr) 112 { 113 return ioread32be(addr); 114 } 115 116 static void xspi_tx8(struct xilinx_spi *xspi) 117 { 118 xspi->write_fn(*xspi->tx_ptr, xspi->regs + XSPI_TXD_OFFSET); 119 xspi->tx_ptr++; 120 } 121 122 static void xspi_tx16(struct xilinx_spi *xspi) 123 { 124 xspi->write_fn(*(u16 *)(xspi->tx_ptr), xspi->regs + XSPI_TXD_OFFSET); 125 xspi->tx_ptr += 2; 126 } 127 128 static void xspi_tx32(struct xilinx_spi *xspi) 129 { 130 xspi->write_fn(*(u32 *)(xspi->tx_ptr), xspi->regs + XSPI_TXD_OFFSET); 131 xspi->tx_ptr += 4; 132 } 133 134 static void xspi_rx8(struct xilinx_spi *xspi) 135 { 136 u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET); 137 if (xspi->rx_ptr) { 138 *xspi->rx_ptr = data & 0xff; 139 xspi->rx_ptr++; 140 } 141 } 142 143 static void xspi_rx16(struct xilinx_spi *xspi) 144 { 145 u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET); 146 if (xspi->rx_ptr) { 147 *(u16 *)(xspi->rx_ptr) = data & 0xffff; 148 xspi->rx_ptr += 2; 149 } 150 } 151 152 static void xspi_rx32(struct xilinx_spi *xspi) 153 { 154 u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET); 155 if (xspi->rx_ptr) { 156 *(u32 *)(xspi->rx_ptr) = data; 157 xspi->rx_ptr += 4; 158 } 159 } 160 161 static void xspi_init_hw(struct xilinx_spi *xspi) 162 { 163 void __iomem *regs_base = xspi->regs; 164 165 /* Reset the SPI device */ 166 xspi->write_fn(XIPIF_V123B_RESET_MASK, 167 regs_base + XIPIF_V123B_RESETR_OFFSET); 168 /* Disable all the interrupts just in case */ 169 xspi->write_fn(0, regs_base + XIPIF_V123B_IIER_OFFSET); 170 /* Enable the global IPIF interrupt */ 171 xspi->write_fn(XIPIF_V123B_GINTR_ENABLE, 172 regs_base + XIPIF_V123B_DGIER_OFFSET); 173 /* Deselect the slave on the SPI bus */ 174 xspi->write_fn(0xffff, regs_base + XSPI_SSR_OFFSET); 175 /* Disable the transmitter, enable Manual Slave Select Assertion, 176 * put SPI controller into master mode, and enable it */ 177 xspi->write_fn(XSPI_CR_TRANS_INHIBIT | XSPI_CR_MANUAL_SSELECT | 178 XSPI_CR_MASTER_MODE | XSPI_CR_ENABLE | XSPI_CR_TXFIFO_RESET | 179 XSPI_CR_RXFIFO_RESET, regs_base + XSPI_CR_OFFSET); 180 } 181 182 static void xilinx_spi_chipselect(struct spi_device *spi, int is_on) 183 { 184 struct xilinx_spi *xspi = spi_master_get_devdata(spi->master); 185 186 if (is_on == BITBANG_CS_INACTIVE) { 187 /* Deselect the slave on the SPI bus */ 188 xspi->write_fn(0xffff, xspi->regs + XSPI_SSR_OFFSET); 189 } else if (is_on == BITBANG_CS_ACTIVE) { 190 /* Set the SPI clock phase and polarity */ 191 u16 cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET) 192 & ~XSPI_CR_MODE_MASK; 193 if (spi->mode & SPI_CPHA) 194 cr |= XSPI_CR_CPHA; 195 if (spi->mode & SPI_CPOL) 196 cr |= XSPI_CR_CPOL; 197 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET); 198 199 /* We do not check spi->max_speed_hz here as the SPI clock 200 * frequency is not software programmable (the IP block design 201 * parameter) 202 */ 203 204 /* Activate the chip select */ 205 xspi->write_fn(~(0x0001 << spi->chip_select), 206 xspi->regs + XSPI_SSR_OFFSET); 207 } 208 } 209 210 /* spi_bitbang requires custom setup_transfer() to be defined if there is a 211 * custom txrx_bufs(). 212 */ 213 static int xilinx_spi_setup_transfer(struct spi_device *spi, 214 struct spi_transfer *t) 215 { 216 return 0; 217 } 218 219 static void xilinx_spi_fill_tx_fifo(struct xilinx_spi *xspi) 220 { 221 u8 sr; 222 223 /* Fill the Tx FIFO with as many bytes as possible */ 224 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET); 225 while ((sr & XSPI_SR_TX_FULL_MASK) == 0 && xspi->remaining_bytes > 0) { 226 if (xspi->tx_ptr) 227 xspi->tx_fn(xspi); 228 else 229 xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET); 230 xspi->remaining_bytes -= xspi->bits_per_word / 8; 231 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET); 232 } 233 } 234 235 static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t) 236 { 237 struct xilinx_spi *xspi = spi_master_get_devdata(spi->master); 238 u32 ipif_ier; 239 240 /* We get here with transmitter inhibited */ 241 242 xspi->tx_ptr = t->tx_buf; 243 xspi->rx_ptr = t->rx_buf; 244 xspi->remaining_bytes = t->len; 245 reinit_completion(&xspi->done); 246 247 248 /* Enable the transmit empty interrupt, which we use to determine 249 * progress on the transmission. 250 */ 251 ipif_ier = xspi->read_fn(xspi->regs + XIPIF_V123B_IIER_OFFSET); 252 xspi->write_fn(ipif_ier | XSPI_INTR_TX_EMPTY, 253 xspi->regs + XIPIF_V123B_IIER_OFFSET); 254 255 for (;;) { 256 u16 cr; 257 u8 sr; 258 259 xilinx_spi_fill_tx_fifo(xspi); 260 261 /* Start the transfer by not inhibiting the transmitter any 262 * longer 263 */ 264 cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET) & 265 ~XSPI_CR_TRANS_INHIBIT; 266 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET); 267 268 wait_for_completion(&xspi->done); 269 270 /* A transmit has just completed. Process received data and 271 * check for more data to transmit. Always inhibit the 272 * transmitter while the Isr refills the transmit register/FIFO, 273 * or make sure it is stopped if we're done. 274 */ 275 cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET); 276 xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT, 277 xspi->regs + XSPI_CR_OFFSET); 278 279 /* Read out all the data from the Rx FIFO */ 280 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET); 281 while ((sr & XSPI_SR_RX_EMPTY_MASK) == 0) { 282 xspi->rx_fn(xspi); 283 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET); 284 } 285 286 /* See if there is more data to send */ 287 if (xspi->remaining_bytes <= 0) 288 break; 289 } 290 291 /* Disable the transmit empty interrupt */ 292 xspi->write_fn(ipif_ier, xspi->regs + XIPIF_V123B_IIER_OFFSET); 293 294 return t->len - xspi->remaining_bytes; 295 } 296 297 298 /* This driver supports single master mode only. Hence Tx FIFO Empty 299 * is the only interrupt we care about. 300 * Receive FIFO Overrun, Transmit FIFO Underrun, Mode Fault, and Slave Mode 301 * Fault are not to happen. 302 */ 303 static irqreturn_t xilinx_spi_irq(int irq, void *dev_id) 304 { 305 struct xilinx_spi *xspi = dev_id; 306 u32 ipif_isr; 307 308 /* Get the IPIF interrupts, and clear them immediately */ 309 ipif_isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET); 310 xspi->write_fn(ipif_isr, xspi->regs + XIPIF_V123B_IISR_OFFSET); 311 312 if (ipif_isr & XSPI_INTR_TX_EMPTY) { /* Transmission completed */ 313 complete(&xspi->done); 314 } 315 316 return IRQ_HANDLED; 317 } 318 319 static const struct of_device_id xilinx_spi_of_match[] = { 320 { .compatible = "xlnx,xps-spi-2.00.a", }, 321 { .compatible = "xlnx,xps-spi-2.00.b", }, 322 {} 323 }; 324 MODULE_DEVICE_TABLE(of, xilinx_spi_of_match); 325 326 static int xilinx_spi_probe(struct platform_device *pdev) 327 { 328 struct xilinx_spi *xspi; 329 struct xspi_platform_data *pdata; 330 struct resource *res; 331 int ret, num_cs = 0, bits_per_word = 8; 332 struct spi_master *master; 333 u32 tmp; 334 u8 i; 335 336 pdata = dev_get_platdata(&pdev->dev); 337 if (pdata) { 338 num_cs = pdata->num_chipselect; 339 bits_per_word = pdata->bits_per_word; 340 } else { 341 of_property_read_u32(pdev->dev.of_node, "xlnx,num-ss-bits", 342 &num_cs); 343 } 344 345 if (!num_cs) { 346 dev_err(&pdev->dev, 347 "Missing slave select configuration data\n"); 348 return -EINVAL; 349 } 350 351 master = spi_alloc_master(&pdev->dev, sizeof(struct xilinx_spi)); 352 if (!master) 353 return -ENODEV; 354 355 /* the spi->mode bits understood by this driver: */ 356 master->mode_bits = SPI_CPOL | SPI_CPHA; 357 358 xspi = spi_master_get_devdata(master); 359 xspi->bitbang.master = master; 360 xspi->bitbang.chipselect = xilinx_spi_chipselect; 361 xspi->bitbang.setup_transfer = xilinx_spi_setup_transfer; 362 xspi->bitbang.txrx_bufs = xilinx_spi_txrx_bufs; 363 init_completion(&xspi->done); 364 365 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 366 xspi->regs = devm_ioremap_resource(&pdev->dev, res); 367 if (IS_ERR(xspi->regs)) { 368 ret = PTR_ERR(xspi->regs); 369 goto put_master; 370 } 371 372 master->bus_num = pdev->id; 373 master->num_chipselect = num_cs; 374 master->dev.of_node = pdev->dev.of_node; 375 376 /* 377 * Detect endianess on the IP via loop bit in CR. Detection 378 * must be done before reset is sent because incorrect reset 379 * value generates error interrupt. 380 * Setup little endian helper functions first and try to use them 381 * and check if bit was correctly setup or not. 382 */ 383 xspi->read_fn = xspi_read32; 384 xspi->write_fn = xspi_write32; 385 386 xspi->write_fn(XSPI_CR_LOOP, xspi->regs + XSPI_CR_OFFSET); 387 tmp = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET); 388 tmp &= XSPI_CR_LOOP; 389 if (tmp != XSPI_CR_LOOP) { 390 xspi->read_fn = xspi_read32_be; 391 xspi->write_fn = xspi_write32_be; 392 } 393 394 master->bits_per_word_mask = SPI_BPW_MASK(bits_per_word); 395 xspi->bits_per_word = bits_per_word; 396 if (xspi->bits_per_word == 8) { 397 xspi->tx_fn = xspi_tx8; 398 xspi->rx_fn = xspi_rx8; 399 } else if (xspi->bits_per_word == 16) { 400 xspi->tx_fn = xspi_tx16; 401 xspi->rx_fn = xspi_rx16; 402 } else if (xspi->bits_per_word == 32) { 403 xspi->tx_fn = xspi_tx32; 404 xspi->rx_fn = xspi_rx32; 405 } else { 406 ret = -EINVAL; 407 goto put_master; 408 } 409 410 /* SPI controller initializations */ 411 xspi_init_hw(xspi); 412 413 xspi->irq = platform_get_irq(pdev, 0); 414 if (xspi->irq < 0) { 415 ret = xspi->irq; 416 goto put_master; 417 } 418 419 /* Register for SPI Interrupt */ 420 ret = devm_request_irq(&pdev->dev, xspi->irq, xilinx_spi_irq, 0, 421 dev_name(&pdev->dev), xspi); 422 if (ret) 423 goto put_master; 424 425 ret = spi_bitbang_start(&xspi->bitbang); 426 if (ret) { 427 dev_err(&pdev->dev, "spi_bitbang_start FAILED\n"); 428 goto put_master; 429 } 430 431 dev_info(&pdev->dev, "at 0x%08llX mapped to 0x%p, irq=%d\n", 432 (unsigned long long)res->start, xspi->regs, xspi->irq); 433 434 if (pdata) { 435 for (i = 0; i < pdata->num_devices; i++) 436 spi_new_device(master, pdata->devices + i); 437 } 438 439 platform_set_drvdata(pdev, master); 440 return 0; 441 442 put_master: 443 spi_master_put(master); 444 445 return ret; 446 } 447 448 static int xilinx_spi_remove(struct platform_device *pdev) 449 { 450 struct spi_master *master = platform_get_drvdata(pdev); 451 struct xilinx_spi *xspi = spi_master_get_devdata(master); 452 void __iomem *regs_base = xspi->regs; 453 454 spi_bitbang_stop(&xspi->bitbang); 455 456 /* Disable all the interrupts just in case */ 457 xspi->write_fn(0, regs_base + XIPIF_V123B_IIER_OFFSET); 458 /* Disable the global IPIF interrupt */ 459 xspi->write_fn(0, regs_base + XIPIF_V123B_DGIER_OFFSET); 460 461 spi_master_put(xspi->bitbang.master); 462 463 return 0; 464 } 465 466 /* work with hotplug and coldplug */ 467 MODULE_ALIAS("platform:" XILINX_SPI_NAME); 468 469 static struct platform_driver xilinx_spi_driver = { 470 .probe = xilinx_spi_probe, 471 .remove = xilinx_spi_remove, 472 .driver = { 473 .name = XILINX_SPI_NAME, 474 .owner = THIS_MODULE, 475 .of_match_table = xilinx_spi_of_match, 476 }, 477 }; 478 module_platform_driver(xilinx_spi_driver); 479 480 MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>"); 481 MODULE_DESCRIPTION("Xilinx SPI driver"); 482 MODULE_LICENSE("GPL"); 483