1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * SH RSPI driver 4 * 5 * Copyright (C) 2012, 2013 Renesas Solutions Corp. 6 * Copyright (C) 2014 Glider bvba 7 * 8 * Based on spi-sh.c: 9 * Copyright (C) 2011 Renesas Solutions Corp. 10 */ 11 12 #include <linux/module.h> 13 #include <linux/kernel.h> 14 #include <linux/sched.h> 15 #include <linux/errno.h> 16 #include <linux/interrupt.h> 17 #include <linux/platform_device.h> 18 #include <linux/io.h> 19 #include <linux/clk.h> 20 #include <linux/dmaengine.h> 21 #include <linux/dma-mapping.h> 22 #include <linux/of.h> 23 #include <linux/pm_runtime.h> 24 #include <linux/reset.h> 25 #include <linux/sh_dma.h> 26 #include <linux/spi/spi.h> 27 #include <linux/spinlock.h> 28 29 #define RSPI_SPCR 0x00 /* Control Register */ 30 #define RSPI_SSLP 0x01 /* Slave Select Polarity Register */ 31 #define RSPI_SPPCR 0x02 /* Pin Control Register */ 32 #define RSPI_SPSR 0x03 /* Status Register */ 33 #define RSPI_SPDR 0x04 /* Data Register */ 34 #define RSPI_SPSCR 0x08 /* Sequence Control Register */ 35 #define RSPI_SPSSR 0x09 /* Sequence Status Register */ 36 #define RSPI_SPBR 0x0a /* Bit Rate Register */ 37 #define RSPI_SPDCR 0x0b /* Data Control Register */ 38 #define RSPI_SPCKD 0x0c /* Clock Delay Register */ 39 #define RSPI_SSLND 0x0d /* Slave Select Negation Delay Register */ 40 #define RSPI_SPND 0x0e /* Next-Access Delay Register */ 41 #define RSPI_SPCR2 0x0f /* Control Register 2 (SH only) */ 42 #define RSPI_SPCMD0 0x10 /* Command Register 0 */ 43 #define RSPI_SPCMD1 0x12 /* Command Register 1 */ 44 #define RSPI_SPCMD2 0x14 /* Command Register 2 */ 45 #define RSPI_SPCMD3 0x16 /* Command Register 3 */ 46 #define RSPI_SPCMD4 0x18 /* Command Register 4 */ 47 #define RSPI_SPCMD5 0x1a /* Command Register 5 */ 48 #define RSPI_SPCMD6 0x1c /* Command Register 6 */ 49 #define RSPI_SPCMD7 0x1e /* Command Register 7 */ 50 #define RSPI_SPCMD(i) (RSPI_SPCMD0 + (i) * 2) 51 #define RSPI_NUM_SPCMD 8 52 #define RSPI_RZ_NUM_SPCMD 4 53 #define QSPI_NUM_SPCMD 4 54 55 /* RSPI on RZ only */ 56 #define RSPI_SPBFCR 0x20 /* Buffer Control Register */ 57 #define RSPI_SPBFDR 0x22 /* Buffer Data Count Setting Register */ 58 59 /* QSPI only */ 60 #define QSPI_SPBFCR 0x18 /* Buffer Control Register */ 61 #define QSPI_SPBDCR 0x1a /* Buffer Data Count Register */ 62 #define QSPI_SPBMUL0 0x1c /* Transfer Data Length Multiplier Setting Register 0 */ 63 #define QSPI_SPBMUL1 0x20 /* Transfer Data Length Multiplier Setting Register 1 */ 64 #define QSPI_SPBMUL2 0x24 /* Transfer Data Length Multiplier Setting Register 2 */ 65 #define QSPI_SPBMUL3 0x28 /* Transfer Data Length Multiplier Setting Register 3 */ 66 #define QSPI_SPBMUL(i) (QSPI_SPBMUL0 + (i) * 4) 67 68 /* SPCR - Control Register */ 69 #define SPCR_SPRIE 0x80 /* Receive Interrupt Enable */ 70 #define SPCR_SPE 0x40 /* Function Enable */ 71 #define SPCR_SPTIE 0x20 /* Transmit Interrupt Enable */ 72 #define SPCR_SPEIE 0x10 /* Error Interrupt Enable */ 73 #define SPCR_MSTR 0x08 /* Master/Slave Mode Select */ 74 #define SPCR_MODFEN 0x04 /* Mode Fault Error Detection Enable */ 75 /* RSPI on SH only */ 76 #define SPCR_TXMD 0x02 /* TX Only Mode (vs. Full Duplex) */ 77 #define SPCR_SPMS 0x01 /* 3-wire Mode (vs. 4-wire) */ 78 /* QSPI on R-Car Gen2 only */ 79 #define SPCR_WSWAP 0x02 /* Word Swap of read-data for DMAC */ 80 #define SPCR_BSWAP 0x01 /* Byte Swap of read-data for DMAC */ 81 82 /* SSLP - Slave Select Polarity Register */ 83 #define SSLP_SSLP(i) BIT(i) /* SSLi Signal Polarity Setting */ 84 85 /* SPPCR - Pin Control Register */ 86 #define SPPCR_MOIFE 0x20 /* MOSI Idle Value Fixing Enable */ 87 #define SPPCR_MOIFV 0x10 /* MOSI Idle Fixed Value */ 88 #define SPPCR_SPOM 0x04 89 #define SPPCR_SPLP2 0x02 /* Loopback Mode 2 (non-inverting) */ 90 #define SPPCR_SPLP 0x01 /* Loopback Mode (inverting) */ 91 92 #define SPPCR_IO3FV 0x04 /* Single-/Dual-SPI Mode IO3 Output Fixed Value */ 93 #define SPPCR_IO2FV 0x04 /* Single-/Dual-SPI Mode IO2 Output Fixed Value */ 94 95 /* SPSR - Status Register */ 96 #define SPSR_SPRF 0x80 /* Receive Buffer Full Flag */ 97 #define SPSR_TEND 0x40 /* Transmit End */ 98 #define SPSR_SPTEF 0x20 /* Transmit Buffer Empty Flag */ 99 #define SPSR_PERF 0x08 /* Parity Error Flag */ 100 #define SPSR_MODF 0x04 /* Mode Fault Error Flag */ 101 #define SPSR_IDLNF 0x02 /* RSPI Idle Flag */ 102 #define SPSR_OVRF 0x01 /* Overrun Error Flag (RSPI only) */ 103 104 /* SPSCR - Sequence Control Register */ 105 #define SPSCR_SPSLN_MASK 0x07 /* Sequence Length Specification */ 106 107 /* SPSSR - Sequence Status Register */ 108 #define SPSSR_SPECM_MASK 0x70 /* Command Error Mask */ 109 #define SPSSR_SPCP_MASK 0x07 /* Command Pointer Mask */ 110 111 /* SPDCR - Data Control Register */ 112 #define SPDCR_TXDMY 0x80 /* Dummy Data Transmission Enable */ 113 #define SPDCR_SPLW1 0x40 /* Access Width Specification (RZ) */ 114 #define SPDCR_SPLW0 0x20 /* Access Width Specification (RZ) */ 115 #define SPDCR_SPLLWORD (SPDCR_SPLW1 | SPDCR_SPLW0) 116 #define SPDCR_SPLWORD SPDCR_SPLW1 117 #define SPDCR_SPLBYTE SPDCR_SPLW0 118 #define SPDCR_SPLW 0x20 /* Access Width Specification (SH) */ 119 #define SPDCR_SPRDTD 0x10 /* Receive Transmit Data Select (SH) */ 120 #define SPDCR_SLSEL1 0x08 121 #define SPDCR_SLSEL0 0x04 122 #define SPDCR_SLSEL_MASK 0x0c /* SSL1 Output Select (SH) */ 123 #define SPDCR_SPFC1 0x02 124 #define SPDCR_SPFC0 0x01 125 #define SPDCR_SPFC_MASK 0x03 /* Frame Count Setting (1-4) (SH) */ 126 127 /* SPCKD - Clock Delay Register */ 128 #define SPCKD_SCKDL_MASK 0x07 /* Clock Delay Setting (1-8) */ 129 130 /* SSLND - Slave Select Negation Delay Register */ 131 #define SSLND_SLNDL_MASK 0x07 /* SSL Negation Delay Setting (1-8) */ 132 133 /* SPND - Next-Access Delay Register */ 134 #define SPND_SPNDL_MASK 0x07 /* Next-Access Delay Setting (1-8) */ 135 136 /* SPCR2 - Control Register 2 */ 137 #define SPCR2_PTE 0x08 /* Parity Self-Test Enable */ 138 #define SPCR2_SPIE 0x04 /* Idle Interrupt Enable */ 139 #define SPCR2_SPOE 0x02 /* Odd Parity Enable (vs. Even) */ 140 #define SPCR2_SPPE 0x01 /* Parity Enable */ 141 142 /* SPCMDn - Command Registers */ 143 #define SPCMD_SCKDEN 0x8000 /* Clock Delay Setting Enable */ 144 #define SPCMD_SLNDEN 0x4000 /* SSL Negation Delay Setting Enable */ 145 #define SPCMD_SPNDEN 0x2000 /* Next-Access Delay Enable */ 146 #define SPCMD_LSBF 0x1000 /* LSB First */ 147 #define SPCMD_SPB_MASK 0x0f00 /* Data Length Setting */ 148 #define SPCMD_SPB_8_TO_16(bit) (((bit - 1) << 8) & SPCMD_SPB_MASK) 149 #define SPCMD_SPB_8BIT 0x0000 /* QSPI only */ 150 #define SPCMD_SPB_16BIT 0x0100 151 #define SPCMD_SPB_20BIT 0x0000 152 #define SPCMD_SPB_24BIT 0x0100 153 #define SPCMD_SPB_32BIT 0x0200 154 #define SPCMD_SSLKP 0x0080 /* SSL Signal Level Keeping */ 155 #define SPCMD_SPIMOD_MASK 0x0060 /* SPI Operating Mode (QSPI only) */ 156 #define SPCMD_SPIMOD1 0x0040 157 #define SPCMD_SPIMOD0 0x0020 158 #define SPCMD_SPIMOD_SINGLE 0 159 #define SPCMD_SPIMOD_DUAL SPCMD_SPIMOD0 160 #define SPCMD_SPIMOD_QUAD SPCMD_SPIMOD1 161 #define SPCMD_SPRW 0x0010 /* SPI Read/Write Access (Dual/Quad) */ 162 #define SPCMD_SSLA(i) ((i) << 4) /* SSL Assert Signal Setting */ 163 #define SPCMD_BRDV_MASK 0x000c /* Bit Rate Division Setting */ 164 #define SPCMD_BRDV(brdv) ((brdv) << 2) 165 #define SPCMD_CPOL 0x0002 /* Clock Polarity Setting */ 166 #define SPCMD_CPHA 0x0001 /* Clock Phase Setting */ 167 168 /* SPBFCR - Buffer Control Register */ 169 #define SPBFCR_TXRST 0x80 /* Transmit Buffer Data Reset */ 170 #define SPBFCR_RXRST 0x40 /* Receive Buffer Data Reset */ 171 #define SPBFCR_TXTRG_MASK 0x30 /* Transmit Buffer Data Triggering Number */ 172 #define SPBFCR_RXTRG_MASK 0x07 /* Receive Buffer Data Triggering Number */ 173 /* QSPI on R-Car Gen2 */ 174 #define SPBFCR_TXTRG_1B 0x00 /* 31 bytes (1 byte available) */ 175 #define SPBFCR_TXTRG_32B 0x30 /* 0 byte (32 bytes available) */ 176 #define SPBFCR_RXTRG_1B 0x00 /* 1 byte (31 bytes available) */ 177 #define SPBFCR_RXTRG_32B 0x07 /* 32 bytes (0 byte available) */ 178 179 #define QSPI_BUFFER_SIZE 32u 180 181 struct rspi_data { 182 void __iomem *addr; 183 u32 speed_hz; 184 struct spi_controller *ctlr; 185 struct platform_device *pdev; 186 wait_queue_head_t wait; 187 spinlock_t lock; /* Protects RMW-access to RSPI_SSLP */ 188 struct clk *clk; 189 u16 spcmd; 190 u8 spsr; 191 u8 sppcr; 192 int rx_irq, tx_irq; 193 const struct spi_ops *ops; 194 195 unsigned dma_callbacked:1; 196 unsigned byte_access:1; 197 }; 198 199 static void rspi_write8(const struct rspi_data *rspi, u8 data, u16 offset) 200 { 201 iowrite8(data, rspi->addr + offset); 202 } 203 204 static void rspi_write16(const struct rspi_data *rspi, u16 data, u16 offset) 205 { 206 iowrite16(data, rspi->addr + offset); 207 } 208 209 static void rspi_write32(const struct rspi_data *rspi, u32 data, u16 offset) 210 { 211 iowrite32(data, rspi->addr + offset); 212 } 213 214 static u8 rspi_read8(const struct rspi_data *rspi, u16 offset) 215 { 216 return ioread8(rspi->addr + offset); 217 } 218 219 static u16 rspi_read16(const struct rspi_data *rspi, u16 offset) 220 { 221 return ioread16(rspi->addr + offset); 222 } 223 224 static void rspi_write_data(const struct rspi_data *rspi, u16 data) 225 { 226 if (rspi->byte_access) 227 rspi_write8(rspi, data, RSPI_SPDR); 228 else /* 16 bit */ 229 rspi_write16(rspi, data, RSPI_SPDR); 230 } 231 232 static u16 rspi_read_data(const struct rspi_data *rspi) 233 { 234 if (rspi->byte_access) 235 return rspi_read8(rspi, RSPI_SPDR); 236 else /* 16 bit */ 237 return rspi_read16(rspi, RSPI_SPDR); 238 } 239 240 /* optional functions */ 241 struct spi_ops { 242 int (*set_config_register)(struct rspi_data *rspi, int access_size); 243 int (*transfer_one)(struct spi_controller *ctlr, 244 struct spi_device *spi, struct spi_transfer *xfer); 245 u16 extra_mode_bits; 246 u16 min_div; 247 u16 max_div; 248 u16 flags; 249 u16 fifo_size; 250 u8 num_hw_ss; 251 }; 252 253 static void rspi_set_rate(struct rspi_data *rspi) 254 { 255 unsigned long clksrc; 256 int brdv = 0, spbr; 257 258 clksrc = clk_get_rate(rspi->clk); 259 spbr = DIV_ROUND_UP(clksrc, 2 * rspi->speed_hz) - 1; 260 while (spbr > 255 && brdv < 3) { 261 brdv++; 262 spbr = DIV_ROUND_UP(spbr + 1, 2) - 1; 263 } 264 265 rspi_write8(rspi, clamp(spbr, 0, 255), RSPI_SPBR); 266 rspi->spcmd |= SPCMD_BRDV(brdv); 267 rspi->speed_hz = DIV_ROUND_UP(clksrc, (2U << brdv) * (spbr + 1)); 268 } 269 270 /* 271 * functions for RSPI on legacy SH 272 */ 273 static int rspi_set_config_register(struct rspi_data *rspi, int access_size) 274 { 275 /* Sets output mode, MOSI signal, and (optionally) loopback */ 276 rspi_write8(rspi, rspi->sppcr, RSPI_SPPCR); 277 278 /* Sets transfer bit rate */ 279 rspi_set_rate(rspi); 280 281 /* Disable dummy transmission, set 16-bit word access, 1 frame */ 282 rspi_write8(rspi, 0, RSPI_SPDCR); 283 rspi->byte_access = 0; 284 285 /* Sets RSPCK, SSL, next-access delay value */ 286 rspi_write8(rspi, 0x00, RSPI_SPCKD); 287 rspi_write8(rspi, 0x00, RSPI_SSLND); 288 rspi_write8(rspi, 0x00, RSPI_SPND); 289 290 /* Sets parity, interrupt mask */ 291 rspi_write8(rspi, 0x00, RSPI_SPCR2); 292 293 /* Resets sequencer */ 294 rspi_write8(rspi, 0, RSPI_SPSCR); 295 rspi->spcmd |= SPCMD_SPB_8_TO_16(access_size); 296 rspi_write16(rspi, rspi->spcmd, RSPI_SPCMD0); 297 298 /* Sets RSPI mode */ 299 rspi_write8(rspi, SPCR_MSTR, RSPI_SPCR); 300 301 return 0; 302 } 303 304 /* 305 * functions for RSPI on RZ 306 */ 307 static int rspi_rz_set_config_register(struct rspi_data *rspi, int access_size) 308 { 309 /* Sets output mode, MOSI signal, and (optionally) loopback */ 310 rspi_write8(rspi, rspi->sppcr, RSPI_SPPCR); 311 312 /* Sets transfer bit rate */ 313 rspi_set_rate(rspi); 314 315 /* Disable dummy transmission, set byte access */ 316 rspi_write8(rspi, SPDCR_SPLBYTE, RSPI_SPDCR); 317 rspi->byte_access = 1; 318 319 /* Sets RSPCK, SSL, next-access delay value */ 320 rspi_write8(rspi, 0x00, RSPI_SPCKD); 321 rspi_write8(rspi, 0x00, RSPI_SSLND); 322 rspi_write8(rspi, 0x00, RSPI_SPND); 323 324 /* Resets sequencer */ 325 rspi_write8(rspi, 0, RSPI_SPSCR); 326 rspi->spcmd |= SPCMD_SPB_8_TO_16(access_size); 327 rspi_write16(rspi, rspi->spcmd, RSPI_SPCMD0); 328 329 /* Sets RSPI mode */ 330 rspi_write8(rspi, SPCR_MSTR, RSPI_SPCR); 331 332 return 0; 333 } 334 335 /* 336 * functions for QSPI 337 */ 338 static int qspi_set_config_register(struct rspi_data *rspi, int access_size) 339 { 340 unsigned long clksrc; 341 int brdv = 0, spbr; 342 343 /* Sets output mode, MOSI signal, and (optionally) loopback */ 344 rspi_write8(rspi, rspi->sppcr, RSPI_SPPCR); 345 346 /* Sets transfer bit rate */ 347 clksrc = clk_get_rate(rspi->clk); 348 if (rspi->speed_hz >= clksrc) { 349 spbr = 0; 350 rspi->speed_hz = clksrc; 351 } else { 352 spbr = DIV_ROUND_UP(clksrc, 2 * rspi->speed_hz); 353 while (spbr > 255 && brdv < 3) { 354 brdv++; 355 spbr = DIV_ROUND_UP(spbr, 2); 356 } 357 spbr = clamp(spbr, 0, 255); 358 rspi->speed_hz = DIV_ROUND_UP(clksrc, (2U << brdv) * spbr); 359 } 360 rspi_write8(rspi, spbr, RSPI_SPBR); 361 rspi->spcmd |= SPCMD_BRDV(brdv); 362 363 /* Disable dummy transmission, set byte access */ 364 rspi_write8(rspi, 0, RSPI_SPDCR); 365 rspi->byte_access = 1; 366 367 /* Sets RSPCK, SSL, next-access delay value */ 368 rspi_write8(rspi, 0x00, RSPI_SPCKD); 369 rspi_write8(rspi, 0x00, RSPI_SSLND); 370 rspi_write8(rspi, 0x00, RSPI_SPND); 371 372 /* Data Length Setting */ 373 if (access_size == 8) 374 rspi->spcmd |= SPCMD_SPB_8BIT; 375 else if (access_size == 16) 376 rspi->spcmd |= SPCMD_SPB_16BIT; 377 else 378 rspi->spcmd |= SPCMD_SPB_32BIT; 379 380 rspi->spcmd |= SPCMD_SCKDEN | SPCMD_SLNDEN | SPCMD_SPNDEN; 381 382 /* Resets transfer data length */ 383 rspi_write32(rspi, 0, QSPI_SPBMUL0); 384 385 /* Resets transmit and receive buffer */ 386 rspi_write8(rspi, SPBFCR_TXRST | SPBFCR_RXRST, QSPI_SPBFCR); 387 /* Sets buffer to allow normal operation */ 388 rspi_write8(rspi, 0x00, QSPI_SPBFCR); 389 390 /* Resets sequencer */ 391 rspi_write8(rspi, 0, RSPI_SPSCR); 392 rspi_write16(rspi, rspi->spcmd, RSPI_SPCMD0); 393 394 /* Sets RSPI mode */ 395 rspi_write8(rspi, SPCR_MSTR, RSPI_SPCR); 396 397 return 0; 398 } 399 400 static void qspi_update(const struct rspi_data *rspi, u8 mask, u8 val, u8 reg) 401 { 402 u8 data; 403 404 data = rspi_read8(rspi, reg); 405 data &= ~mask; 406 data |= (val & mask); 407 rspi_write8(rspi, data, reg); 408 } 409 410 static unsigned int qspi_set_send_trigger(struct rspi_data *rspi, 411 unsigned int len) 412 { 413 unsigned int n; 414 415 n = min(len, QSPI_BUFFER_SIZE); 416 417 if (len >= QSPI_BUFFER_SIZE) { 418 /* sets triggering number to 32 bytes */ 419 qspi_update(rspi, SPBFCR_TXTRG_MASK, 420 SPBFCR_TXTRG_32B, QSPI_SPBFCR); 421 } else { 422 /* sets triggering number to 1 byte */ 423 qspi_update(rspi, SPBFCR_TXTRG_MASK, 424 SPBFCR_TXTRG_1B, QSPI_SPBFCR); 425 } 426 427 return n; 428 } 429 430 static int qspi_set_receive_trigger(struct rspi_data *rspi, unsigned int len) 431 { 432 unsigned int n; 433 434 n = min(len, QSPI_BUFFER_SIZE); 435 436 if (len >= QSPI_BUFFER_SIZE) { 437 /* sets triggering number to 32 bytes */ 438 qspi_update(rspi, SPBFCR_RXTRG_MASK, 439 SPBFCR_RXTRG_32B, QSPI_SPBFCR); 440 } else { 441 /* sets triggering number to 1 byte */ 442 qspi_update(rspi, SPBFCR_RXTRG_MASK, 443 SPBFCR_RXTRG_1B, QSPI_SPBFCR); 444 } 445 return n; 446 } 447 448 static void rspi_enable_irq(const struct rspi_data *rspi, u8 enable) 449 { 450 rspi_write8(rspi, rspi_read8(rspi, RSPI_SPCR) | enable, RSPI_SPCR); 451 } 452 453 static void rspi_disable_irq(const struct rspi_data *rspi, u8 disable) 454 { 455 rspi_write8(rspi, rspi_read8(rspi, RSPI_SPCR) & ~disable, RSPI_SPCR); 456 } 457 458 static int rspi_wait_for_interrupt(struct rspi_data *rspi, u8 wait_mask, 459 u8 enable_bit) 460 { 461 int ret; 462 463 rspi->spsr = rspi_read8(rspi, RSPI_SPSR); 464 if (rspi->spsr & wait_mask) 465 return 0; 466 467 rspi_enable_irq(rspi, enable_bit); 468 ret = wait_event_timeout(rspi->wait, rspi->spsr & wait_mask, HZ); 469 if (ret == 0 && !(rspi->spsr & wait_mask)) 470 return -ETIMEDOUT; 471 472 return 0; 473 } 474 475 static inline int rspi_wait_for_tx_empty(struct rspi_data *rspi) 476 { 477 return rspi_wait_for_interrupt(rspi, SPSR_SPTEF, SPCR_SPTIE); 478 } 479 480 static inline int rspi_wait_for_rx_full(struct rspi_data *rspi) 481 { 482 return rspi_wait_for_interrupt(rspi, SPSR_SPRF, SPCR_SPRIE); 483 } 484 485 static int rspi_data_out(struct rspi_data *rspi, u8 data) 486 { 487 int error = rspi_wait_for_tx_empty(rspi); 488 if (error < 0) { 489 dev_err(&rspi->ctlr->dev, "transmit timeout\n"); 490 return error; 491 } 492 rspi_write_data(rspi, data); 493 return 0; 494 } 495 496 static int rspi_data_in(struct rspi_data *rspi) 497 { 498 int error; 499 u8 data; 500 501 error = rspi_wait_for_rx_full(rspi); 502 if (error < 0) { 503 dev_err(&rspi->ctlr->dev, "receive timeout\n"); 504 return error; 505 } 506 data = rspi_read_data(rspi); 507 return data; 508 } 509 510 static int rspi_pio_transfer(struct rspi_data *rspi, const u8 *tx, u8 *rx, 511 unsigned int n) 512 { 513 while (n-- > 0) { 514 if (tx) { 515 int ret = rspi_data_out(rspi, *tx++); 516 if (ret < 0) 517 return ret; 518 } 519 if (rx) { 520 int ret = rspi_data_in(rspi); 521 if (ret < 0) 522 return ret; 523 *rx++ = ret; 524 } 525 } 526 527 return 0; 528 } 529 530 static void rspi_dma_complete(void *arg) 531 { 532 struct rspi_data *rspi = arg; 533 534 rspi->dma_callbacked = 1; 535 wake_up_interruptible(&rspi->wait); 536 } 537 538 static int rspi_dma_transfer(struct rspi_data *rspi, struct sg_table *tx, 539 struct sg_table *rx) 540 { 541 struct dma_async_tx_descriptor *desc_tx = NULL, *desc_rx = NULL; 542 u8 irq_mask = 0; 543 unsigned int other_irq = 0; 544 dma_cookie_t cookie; 545 int ret; 546 547 /* First prepare and submit the DMA request(s), as this may fail */ 548 if (rx) { 549 desc_rx = dmaengine_prep_slave_sg(rspi->ctlr->dma_rx, rx->sgl, 550 rx->nents, DMA_DEV_TO_MEM, 551 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 552 if (!desc_rx) { 553 ret = -EAGAIN; 554 goto no_dma_rx; 555 } 556 557 desc_rx->callback = rspi_dma_complete; 558 desc_rx->callback_param = rspi; 559 cookie = dmaengine_submit(desc_rx); 560 if (dma_submit_error(cookie)) { 561 ret = cookie; 562 goto no_dma_rx; 563 } 564 565 irq_mask |= SPCR_SPRIE; 566 } 567 568 if (tx) { 569 desc_tx = dmaengine_prep_slave_sg(rspi->ctlr->dma_tx, tx->sgl, 570 tx->nents, DMA_MEM_TO_DEV, 571 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 572 if (!desc_tx) { 573 ret = -EAGAIN; 574 goto no_dma_tx; 575 } 576 577 if (rx) { 578 /* No callback */ 579 desc_tx->callback = NULL; 580 } else { 581 desc_tx->callback = rspi_dma_complete; 582 desc_tx->callback_param = rspi; 583 } 584 cookie = dmaengine_submit(desc_tx); 585 if (dma_submit_error(cookie)) { 586 ret = cookie; 587 goto no_dma_tx; 588 } 589 590 irq_mask |= SPCR_SPTIE; 591 } 592 593 /* 594 * DMAC needs SPxIE, but if SPxIE is set, the IRQ routine will be 595 * called. So, this driver disables the IRQ while DMA transfer. 596 */ 597 if (tx) 598 disable_irq(other_irq = rspi->tx_irq); 599 if (rx && rspi->rx_irq != other_irq) 600 disable_irq(rspi->rx_irq); 601 602 rspi_enable_irq(rspi, irq_mask); 603 rspi->dma_callbacked = 0; 604 605 /* Now start DMA */ 606 if (rx) 607 dma_async_issue_pending(rspi->ctlr->dma_rx); 608 if (tx) 609 dma_async_issue_pending(rspi->ctlr->dma_tx); 610 611 ret = wait_event_interruptible_timeout(rspi->wait, 612 rspi->dma_callbacked, HZ); 613 if (ret > 0 && rspi->dma_callbacked) { 614 ret = 0; 615 if (tx) 616 dmaengine_synchronize(rspi->ctlr->dma_tx); 617 if (rx) 618 dmaengine_synchronize(rspi->ctlr->dma_rx); 619 } else { 620 if (!ret) { 621 dev_err(&rspi->ctlr->dev, "DMA timeout\n"); 622 ret = -ETIMEDOUT; 623 } 624 if (tx) 625 dmaengine_terminate_sync(rspi->ctlr->dma_tx); 626 if (rx) 627 dmaengine_terminate_sync(rspi->ctlr->dma_rx); 628 } 629 630 rspi_disable_irq(rspi, irq_mask); 631 632 if (tx) 633 enable_irq(rspi->tx_irq); 634 if (rx && rspi->rx_irq != other_irq) 635 enable_irq(rspi->rx_irq); 636 637 return ret; 638 639 no_dma_tx: 640 if (rx) 641 dmaengine_terminate_sync(rspi->ctlr->dma_rx); 642 no_dma_rx: 643 if (ret == -EAGAIN) { 644 dev_warn_once(&rspi->ctlr->dev, 645 "DMA not available, falling back to PIO\n"); 646 } 647 return ret; 648 } 649 650 static void rspi_receive_init(const struct rspi_data *rspi) 651 { 652 u8 spsr; 653 654 spsr = rspi_read8(rspi, RSPI_SPSR); 655 if (spsr & SPSR_SPRF) 656 rspi_read_data(rspi); /* dummy read */ 657 if (spsr & SPSR_OVRF) 658 rspi_write8(rspi, rspi_read8(rspi, RSPI_SPSR) & ~SPSR_OVRF, 659 RSPI_SPSR); 660 } 661 662 static void rspi_rz_receive_init(const struct rspi_data *rspi) 663 { 664 rspi_receive_init(rspi); 665 rspi_write8(rspi, SPBFCR_TXRST | SPBFCR_RXRST, RSPI_SPBFCR); 666 rspi_write8(rspi, 0, RSPI_SPBFCR); 667 } 668 669 static void qspi_receive_init(const struct rspi_data *rspi) 670 { 671 u8 spsr; 672 673 spsr = rspi_read8(rspi, RSPI_SPSR); 674 if (spsr & SPSR_SPRF) 675 rspi_read_data(rspi); /* dummy read */ 676 rspi_write8(rspi, SPBFCR_TXRST | SPBFCR_RXRST, QSPI_SPBFCR); 677 rspi_write8(rspi, 0, QSPI_SPBFCR); 678 } 679 680 static bool __rspi_can_dma(const struct rspi_data *rspi, 681 const struct spi_transfer *xfer) 682 { 683 return xfer->len > rspi->ops->fifo_size; 684 } 685 686 static bool rspi_can_dma(struct spi_controller *ctlr, struct spi_device *spi, 687 struct spi_transfer *xfer) 688 { 689 struct rspi_data *rspi = spi_controller_get_devdata(ctlr); 690 691 return __rspi_can_dma(rspi, xfer); 692 } 693 694 static int rspi_dma_check_then_transfer(struct rspi_data *rspi, 695 struct spi_transfer *xfer) 696 { 697 if (!rspi->ctlr->can_dma || !__rspi_can_dma(rspi, xfer)) 698 return -EAGAIN; 699 700 /* rx_buf can be NULL on RSPI on SH in TX-only Mode */ 701 return rspi_dma_transfer(rspi, &xfer->tx_sg, 702 xfer->rx_buf ? &xfer->rx_sg : NULL); 703 } 704 705 static int rspi_common_transfer(struct rspi_data *rspi, 706 struct spi_transfer *xfer) 707 { 708 int ret; 709 710 xfer->effective_speed_hz = rspi->speed_hz; 711 712 ret = rspi_dma_check_then_transfer(rspi, xfer); 713 if (ret != -EAGAIN) 714 return ret; 715 716 ret = rspi_pio_transfer(rspi, xfer->tx_buf, xfer->rx_buf, xfer->len); 717 if (ret < 0) 718 return ret; 719 720 /* Wait for the last transmission */ 721 rspi_wait_for_tx_empty(rspi); 722 723 return 0; 724 } 725 726 static int rspi_transfer_one(struct spi_controller *ctlr, 727 struct spi_device *spi, struct spi_transfer *xfer) 728 { 729 struct rspi_data *rspi = spi_controller_get_devdata(ctlr); 730 u8 spcr; 731 732 spcr = rspi_read8(rspi, RSPI_SPCR); 733 if (xfer->rx_buf) { 734 rspi_receive_init(rspi); 735 spcr &= ~SPCR_TXMD; 736 } else { 737 spcr |= SPCR_TXMD; 738 } 739 rspi_write8(rspi, spcr, RSPI_SPCR); 740 741 return rspi_common_transfer(rspi, xfer); 742 } 743 744 static int rspi_rz_transfer_one(struct spi_controller *ctlr, 745 struct spi_device *spi, 746 struct spi_transfer *xfer) 747 { 748 struct rspi_data *rspi = spi_controller_get_devdata(ctlr); 749 750 rspi_rz_receive_init(rspi); 751 752 return rspi_common_transfer(rspi, xfer); 753 } 754 755 static int qspi_trigger_transfer_out_in(struct rspi_data *rspi, const u8 *tx, 756 u8 *rx, unsigned int len) 757 { 758 unsigned int i, n; 759 int ret; 760 761 while (len > 0) { 762 n = qspi_set_send_trigger(rspi, len); 763 qspi_set_receive_trigger(rspi, len); 764 ret = rspi_wait_for_tx_empty(rspi); 765 if (ret < 0) { 766 dev_err(&rspi->ctlr->dev, "transmit timeout\n"); 767 return ret; 768 } 769 for (i = 0; i < n; i++) 770 rspi_write_data(rspi, *tx++); 771 772 ret = rspi_wait_for_rx_full(rspi); 773 if (ret < 0) { 774 dev_err(&rspi->ctlr->dev, "receive timeout\n"); 775 return ret; 776 } 777 for (i = 0; i < n; i++) 778 *rx++ = rspi_read_data(rspi); 779 780 len -= n; 781 } 782 783 return 0; 784 } 785 786 static int qspi_transfer_out_in(struct rspi_data *rspi, 787 struct spi_transfer *xfer) 788 { 789 int ret; 790 791 qspi_receive_init(rspi); 792 793 ret = rspi_dma_check_then_transfer(rspi, xfer); 794 if (ret != -EAGAIN) 795 return ret; 796 797 return qspi_trigger_transfer_out_in(rspi, xfer->tx_buf, 798 xfer->rx_buf, xfer->len); 799 } 800 801 static int qspi_transfer_out(struct rspi_data *rspi, struct spi_transfer *xfer) 802 { 803 const u8 *tx = xfer->tx_buf; 804 unsigned int n = xfer->len; 805 unsigned int i, len; 806 int ret; 807 808 if (rspi->ctlr->can_dma && __rspi_can_dma(rspi, xfer)) { 809 ret = rspi_dma_transfer(rspi, &xfer->tx_sg, NULL); 810 if (ret != -EAGAIN) 811 return ret; 812 } 813 814 while (n > 0) { 815 len = qspi_set_send_trigger(rspi, n); 816 ret = rspi_wait_for_tx_empty(rspi); 817 if (ret < 0) { 818 dev_err(&rspi->ctlr->dev, "transmit timeout\n"); 819 return ret; 820 } 821 for (i = 0; i < len; i++) 822 rspi_write_data(rspi, *tx++); 823 824 n -= len; 825 } 826 827 /* Wait for the last transmission */ 828 rspi_wait_for_tx_empty(rspi); 829 830 return 0; 831 } 832 833 static int qspi_transfer_in(struct rspi_data *rspi, struct spi_transfer *xfer) 834 { 835 u8 *rx = xfer->rx_buf; 836 unsigned int n = xfer->len; 837 unsigned int i, len; 838 int ret; 839 840 if (rspi->ctlr->can_dma && __rspi_can_dma(rspi, xfer)) { 841 ret = rspi_dma_transfer(rspi, NULL, &xfer->rx_sg); 842 if (ret != -EAGAIN) 843 return ret; 844 } 845 846 while (n > 0) { 847 len = qspi_set_receive_trigger(rspi, n); 848 ret = rspi_wait_for_rx_full(rspi); 849 if (ret < 0) { 850 dev_err(&rspi->ctlr->dev, "receive timeout\n"); 851 return ret; 852 } 853 for (i = 0; i < len; i++) 854 *rx++ = rspi_read_data(rspi); 855 856 n -= len; 857 } 858 859 return 0; 860 } 861 862 static int qspi_transfer_one(struct spi_controller *ctlr, 863 struct spi_device *spi, struct spi_transfer *xfer) 864 { 865 struct rspi_data *rspi = spi_controller_get_devdata(ctlr); 866 867 xfer->effective_speed_hz = rspi->speed_hz; 868 if (spi->mode & SPI_LOOP) { 869 return qspi_transfer_out_in(rspi, xfer); 870 } else if (xfer->tx_nbits > SPI_NBITS_SINGLE) { 871 /* Quad or Dual SPI Write */ 872 return qspi_transfer_out(rspi, xfer); 873 } else if (xfer->rx_nbits > SPI_NBITS_SINGLE) { 874 /* Quad or Dual SPI Read */ 875 return qspi_transfer_in(rspi, xfer); 876 } else { 877 /* Single SPI Transfer */ 878 return qspi_transfer_out_in(rspi, xfer); 879 } 880 } 881 882 static u16 qspi_transfer_mode(const struct spi_transfer *xfer) 883 { 884 if (xfer->tx_buf) 885 switch (xfer->tx_nbits) { 886 case SPI_NBITS_QUAD: 887 return SPCMD_SPIMOD_QUAD; 888 case SPI_NBITS_DUAL: 889 return SPCMD_SPIMOD_DUAL; 890 default: 891 return 0; 892 } 893 if (xfer->rx_buf) 894 switch (xfer->rx_nbits) { 895 case SPI_NBITS_QUAD: 896 return SPCMD_SPIMOD_QUAD | SPCMD_SPRW; 897 case SPI_NBITS_DUAL: 898 return SPCMD_SPIMOD_DUAL | SPCMD_SPRW; 899 default: 900 return 0; 901 } 902 903 return 0; 904 } 905 906 static int qspi_setup_sequencer(struct rspi_data *rspi, 907 const struct spi_message *msg) 908 { 909 const struct spi_transfer *xfer; 910 unsigned int i = 0, len = 0; 911 u16 current_mode = 0xffff, mode; 912 913 list_for_each_entry(xfer, &msg->transfers, transfer_list) { 914 mode = qspi_transfer_mode(xfer); 915 if (mode == current_mode) { 916 len += xfer->len; 917 continue; 918 } 919 920 /* Transfer mode change */ 921 if (i) { 922 /* Set transfer data length of previous transfer */ 923 rspi_write32(rspi, len, QSPI_SPBMUL(i - 1)); 924 } 925 926 if (i >= QSPI_NUM_SPCMD) { 927 dev_err(&msg->spi->dev, 928 "Too many different transfer modes"); 929 return -EINVAL; 930 } 931 932 /* Program transfer mode for this transfer */ 933 rspi_write16(rspi, rspi->spcmd | mode, RSPI_SPCMD(i)); 934 current_mode = mode; 935 len = xfer->len; 936 i++; 937 } 938 if (i) { 939 /* Set final transfer data length and sequence length */ 940 rspi_write32(rspi, len, QSPI_SPBMUL(i - 1)); 941 rspi_write8(rspi, i - 1, RSPI_SPSCR); 942 } 943 944 return 0; 945 } 946 947 static int rspi_setup(struct spi_device *spi) 948 { 949 struct rspi_data *rspi = spi_controller_get_devdata(spi->controller); 950 u8 sslp; 951 952 if (spi_get_csgpiod(spi, 0)) 953 return 0; 954 955 pm_runtime_get_sync(&rspi->pdev->dev); 956 spin_lock_irq(&rspi->lock); 957 958 sslp = rspi_read8(rspi, RSPI_SSLP); 959 if (spi->mode & SPI_CS_HIGH) 960 sslp |= SSLP_SSLP(spi_get_chipselect(spi, 0)); 961 else 962 sslp &= ~SSLP_SSLP(spi_get_chipselect(spi, 0)); 963 rspi_write8(rspi, sslp, RSPI_SSLP); 964 965 spin_unlock_irq(&rspi->lock); 966 pm_runtime_put(&rspi->pdev->dev); 967 return 0; 968 } 969 970 static int rspi_prepare_message(struct spi_controller *ctlr, 971 struct spi_message *msg) 972 { 973 struct rspi_data *rspi = spi_controller_get_devdata(ctlr); 974 struct spi_device *spi = msg->spi; 975 const struct spi_transfer *xfer; 976 int ret; 977 978 /* 979 * As the Bit Rate Register must not be changed while the device is 980 * active, all transfers in a message must use the same bit rate. 981 * In theory, the sequencer could be enabled, and each Command Register 982 * could divide the base bit rate by a different value. 983 * However, most RSPI variants do not have Transfer Data Length 984 * Multiplier Setting Registers, so each sequence step would be limited 985 * to a single word, making this feature unsuitable for large 986 * transfers, which would gain most from it. 987 */ 988 rspi->speed_hz = spi->max_speed_hz; 989 list_for_each_entry(xfer, &msg->transfers, transfer_list) { 990 if (xfer->speed_hz < rspi->speed_hz) 991 rspi->speed_hz = xfer->speed_hz; 992 } 993 994 rspi->spcmd = SPCMD_SSLKP; 995 if (spi->mode & SPI_CPOL) 996 rspi->spcmd |= SPCMD_CPOL; 997 if (spi->mode & SPI_CPHA) 998 rspi->spcmd |= SPCMD_CPHA; 999 if (spi->mode & SPI_LSB_FIRST) 1000 rspi->spcmd |= SPCMD_LSBF; 1001 1002 /* Configure slave signal to assert */ 1003 rspi->spcmd |= SPCMD_SSLA(spi_get_csgpiod(spi, 0) ? rspi->ctlr->unused_native_cs 1004 : spi_get_chipselect(spi, 0)); 1005 1006 /* CMOS output mode and MOSI signal from previous transfer */ 1007 rspi->sppcr = 0; 1008 if (spi->mode & SPI_LOOP) 1009 rspi->sppcr |= SPPCR_SPLP; 1010 1011 rspi->ops->set_config_register(rspi, 8); 1012 1013 if (msg->spi->mode & 1014 (SPI_TX_DUAL | SPI_TX_QUAD | SPI_RX_DUAL | SPI_RX_QUAD)) { 1015 /* Setup sequencer for messages with multiple transfer modes */ 1016 ret = qspi_setup_sequencer(rspi, msg); 1017 if (ret < 0) 1018 return ret; 1019 } 1020 1021 /* Enable SPI function in master mode */ 1022 rspi_write8(rspi, rspi_read8(rspi, RSPI_SPCR) | SPCR_SPE, RSPI_SPCR); 1023 return 0; 1024 } 1025 1026 static int rspi_unprepare_message(struct spi_controller *ctlr, 1027 struct spi_message *msg) 1028 { 1029 struct rspi_data *rspi = spi_controller_get_devdata(ctlr); 1030 1031 /* Disable SPI function */ 1032 rspi_write8(rspi, rspi_read8(rspi, RSPI_SPCR) & ~SPCR_SPE, RSPI_SPCR); 1033 1034 /* Reset sequencer for Single SPI Transfers */ 1035 rspi_write16(rspi, rspi->spcmd, RSPI_SPCMD0); 1036 rspi_write8(rspi, 0, RSPI_SPSCR); 1037 return 0; 1038 } 1039 1040 static irqreturn_t rspi_irq_mux(int irq, void *_sr) 1041 { 1042 struct rspi_data *rspi = _sr; 1043 u8 spsr; 1044 irqreturn_t ret = IRQ_NONE; 1045 u8 disable_irq = 0; 1046 1047 rspi->spsr = spsr = rspi_read8(rspi, RSPI_SPSR); 1048 if (spsr & SPSR_SPRF) 1049 disable_irq |= SPCR_SPRIE; 1050 if (spsr & SPSR_SPTEF) 1051 disable_irq |= SPCR_SPTIE; 1052 1053 if (disable_irq) { 1054 ret = IRQ_HANDLED; 1055 rspi_disable_irq(rspi, disable_irq); 1056 wake_up(&rspi->wait); 1057 } 1058 1059 return ret; 1060 } 1061 1062 static irqreturn_t rspi_irq_rx(int irq, void *_sr) 1063 { 1064 struct rspi_data *rspi = _sr; 1065 u8 spsr; 1066 1067 rspi->spsr = spsr = rspi_read8(rspi, RSPI_SPSR); 1068 if (spsr & SPSR_SPRF) { 1069 rspi_disable_irq(rspi, SPCR_SPRIE); 1070 wake_up(&rspi->wait); 1071 return IRQ_HANDLED; 1072 } 1073 1074 return 0; 1075 } 1076 1077 static irqreturn_t rspi_irq_tx(int irq, void *_sr) 1078 { 1079 struct rspi_data *rspi = _sr; 1080 u8 spsr; 1081 1082 rspi->spsr = spsr = rspi_read8(rspi, RSPI_SPSR); 1083 if (spsr & SPSR_SPTEF) { 1084 rspi_disable_irq(rspi, SPCR_SPTIE); 1085 wake_up(&rspi->wait); 1086 return IRQ_HANDLED; 1087 } 1088 1089 return 0; 1090 } 1091 1092 static struct dma_chan *rspi_request_dma_chan(struct device *dev, 1093 enum dma_transfer_direction dir, 1094 unsigned int id, 1095 dma_addr_t port_addr) 1096 { 1097 dma_cap_mask_t mask; 1098 struct dma_chan *chan; 1099 struct dma_slave_config cfg; 1100 int ret; 1101 1102 dma_cap_zero(mask); 1103 dma_cap_set(DMA_SLAVE, mask); 1104 1105 chan = dma_request_slave_channel_compat(mask, shdma_chan_filter, 1106 (void *)(unsigned long)id, dev, 1107 dir == DMA_MEM_TO_DEV ? "tx" : "rx"); 1108 if (!chan) { 1109 dev_warn(dev, "dma_request_slave_channel_compat failed\n"); 1110 return NULL; 1111 } 1112 1113 memset(&cfg, 0, sizeof(cfg)); 1114 cfg.dst_addr = port_addr + RSPI_SPDR; 1115 cfg.src_addr = port_addr + RSPI_SPDR; 1116 cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 1117 cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 1118 cfg.direction = dir; 1119 1120 ret = dmaengine_slave_config(chan, &cfg); 1121 if (ret) { 1122 dev_warn(dev, "dmaengine_slave_config failed %d\n", ret); 1123 dma_release_channel(chan); 1124 return NULL; 1125 } 1126 1127 return chan; 1128 } 1129 1130 static int rspi_request_dma(struct device *dev, struct spi_controller *ctlr, 1131 const struct resource *res) 1132 { 1133 unsigned int dma_tx_id, dma_rx_id; 1134 1135 if (dev->of_node) { 1136 /* In the OF case we will get the slave IDs from the DT */ 1137 dma_tx_id = 0; 1138 dma_rx_id = 0; 1139 } else { 1140 /* The driver assumes no error. */ 1141 return 0; 1142 } 1143 1144 ctlr->dma_tx = rspi_request_dma_chan(dev, DMA_MEM_TO_DEV, dma_tx_id, 1145 res->start); 1146 if (!ctlr->dma_tx) 1147 return -ENODEV; 1148 1149 ctlr->dma_rx = rspi_request_dma_chan(dev, DMA_DEV_TO_MEM, dma_rx_id, 1150 res->start); 1151 if (!ctlr->dma_rx) { 1152 dma_release_channel(ctlr->dma_tx); 1153 ctlr->dma_tx = NULL; 1154 return -ENODEV; 1155 } 1156 1157 ctlr->can_dma = rspi_can_dma; 1158 dev_info(dev, "DMA available"); 1159 return 0; 1160 } 1161 1162 static void rspi_release_dma(struct spi_controller *ctlr) 1163 { 1164 if (ctlr->dma_tx) 1165 dma_release_channel(ctlr->dma_tx); 1166 if (ctlr->dma_rx) 1167 dma_release_channel(ctlr->dma_rx); 1168 } 1169 1170 static void rspi_remove(struct platform_device *pdev) 1171 { 1172 struct rspi_data *rspi = platform_get_drvdata(pdev); 1173 1174 rspi_release_dma(rspi->ctlr); 1175 pm_runtime_disable(&pdev->dev); 1176 } 1177 1178 static const struct spi_ops rspi_ops = { 1179 .set_config_register = rspi_set_config_register, 1180 .transfer_one = rspi_transfer_one, 1181 .min_div = 2, 1182 .max_div = 4096, 1183 .flags = SPI_CONTROLLER_MUST_TX, 1184 .fifo_size = 8, 1185 .num_hw_ss = 2, 1186 }; 1187 1188 static const struct spi_ops rspi_rz_ops __maybe_unused = { 1189 .set_config_register = rspi_rz_set_config_register, 1190 .transfer_one = rspi_rz_transfer_one, 1191 .min_div = 2, 1192 .max_div = 4096, 1193 .flags = SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX, 1194 .fifo_size = 8, /* 8 for TX, 32 for RX */ 1195 .num_hw_ss = 1, 1196 }; 1197 1198 static const struct spi_ops qspi_ops __maybe_unused = { 1199 .set_config_register = qspi_set_config_register, 1200 .transfer_one = qspi_transfer_one, 1201 .extra_mode_bits = SPI_TX_DUAL | SPI_TX_QUAD | 1202 SPI_RX_DUAL | SPI_RX_QUAD, 1203 .min_div = 1, 1204 .max_div = 4080, 1205 .flags = SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX, 1206 .fifo_size = 32, 1207 .num_hw_ss = 1, 1208 }; 1209 1210 static const struct of_device_id rspi_of_match[] __maybe_unused = { 1211 /* RSPI on legacy SH */ 1212 { .compatible = "renesas,rspi", .data = &rspi_ops }, 1213 /* RSPI on RZ/A1H */ 1214 { .compatible = "renesas,rspi-rz", .data = &rspi_rz_ops }, 1215 /* QSPI on R-Car Gen2 */ 1216 { .compatible = "renesas,qspi", .data = &qspi_ops }, 1217 { /* sentinel */ } 1218 }; 1219 1220 MODULE_DEVICE_TABLE(of, rspi_of_match); 1221 1222 #ifdef CONFIG_OF 1223 static void rspi_reset_control_assert(void *data) 1224 { 1225 reset_control_assert(data); 1226 } 1227 1228 static int rspi_parse_dt(struct device *dev, struct spi_controller *ctlr) 1229 { 1230 struct reset_control *rstc; 1231 u32 num_cs; 1232 int error; 1233 1234 /* Parse DT properties */ 1235 error = of_property_read_u32(dev->of_node, "num-cs", &num_cs); 1236 if (error) { 1237 dev_err(dev, "of_property_read_u32 num-cs failed %d\n", error); 1238 return error; 1239 } 1240 1241 ctlr->num_chipselect = num_cs; 1242 1243 rstc = devm_reset_control_get_optional_exclusive(dev, NULL); 1244 if (IS_ERR(rstc)) 1245 return dev_err_probe(dev, PTR_ERR(rstc), 1246 "failed to get reset ctrl\n"); 1247 1248 error = reset_control_deassert(rstc); 1249 if (error) { 1250 dev_err(dev, "failed to deassert reset %d\n", error); 1251 return error; 1252 } 1253 1254 error = devm_add_action_or_reset(dev, rspi_reset_control_assert, rstc); 1255 if (error) { 1256 dev_err(dev, "failed to register assert devm action, %d\n", error); 1257 return error; 1258 } 1259 1260 return 0; 1261 } 1262 #else 1263 #define rspi_of_match NULL 1264 static inline int rspi_parse_dt(struct device *dev, struct spi_controller *ctlr) 1265 { 1266 return -EINVAL; 1267 } 1268 #endif /* CONFIG_OF */ 1269 1270 static int rspi_request_irq(struct device *dev, unsigned int irq, 1271 irq_handler_t handler, const char *suffix, 1272 void *dev_id) 1273 { 1274 const char *name = devm_kasprintf(dev, GFP_KERNEL, "%s:%s", 1275 dev_name(dev), suffix); 1276 if (!name) 1277 return -ENOMEM; 1278 1279 return devm_request_irq(dev, irq, handler, 0, name, dev_id); 1280 } 1281 1282 static int rspi_probe(struct platform_device *pdev) 1283 { 1284 struct resource *res; 1285 struct spi_controller *ctlr; 1286 struct rspi_data *rspi; 1287 int ret; 1288 const struct spi_ops *ops; 1289 unsigned long clksrc; 1290 1291 ctlr = spi_alloc_host(&pdev->dev, sizeof(struct rspi_data)); 1292 if (ctlr == NULL) 1293 return -ENOMEM; 1294 1295 ops = of_device_get_match_data(&pdev->dev); 1296 if (ops) { 1297 ret = rspi_parse_dt(&pdev->dev, ctlr); 1298 if (ret) 1299 goto error1; 1300 } else { 1301 ops = (struct spi_ops *)pdev->id_entry->driver_data; 1302 ctlr->num_chipselect = 2; /* default */ 1303 } 1304 1305 rspi = spi_controller_get_devdata(ctlr); 1306 platform_set_drvdata(pdev, rspi); 1307 rspi->ops = ops; 1308 rspi->ctlr = ctlr; 1309 1310 rspi->addr = devm_platform_get_and_ioremap_resource(pdev, 0, &res); 1311 if (IS_ERR(rspi->addr)) { 1312 ret = PTR_ERR(rspi->addr); 1313 goto error1; 1314 } 1315 1316 rspi->clk = devm_clk_get(&pdev->dev, NULL); 1317 if (IS_ERR(rspi->clk)) { 1318 dev_err(&pdev->dev, "cannot get clock\n"); 1319 ret = PTR_ERR(rspi->clk); 1320 goto error1; 1321 } 1322 1323 rspi->pdev = pdev; 1324 pm_runtime_enable(&pdev->dev); 1325 1326 init_waitqueue_head(&rspi->wait); 1327 spin_lock_init(&rspi->lock); 1328 1329 ctlr->bus_num = pdev->id; 1330 ctlr->setup = rspi_setup; 1331 ctlr->auto_runtime_pm = true; 1332 ctlr->transfer_one = ops->transfer_one; 1333 ctlr->prepare_message = rspi_prepare_message; 1334 ctlr->unprepare_message = rspi_unprepare_message; 1335 ctlr->mode_bits = SPI_CPHA | SPI_CPOL | SPI_CS_HIGH | SPI_LSB_FIRST | 1336 SPI_LOOP | ops->extra_mode_bits; 1337 clksrc = clk_get_rate(rspi->clk); 1338 ctlr->min_speed_hz = DIV_ROUND_UP(clksrc, ops->max_div); 1339 ctlr->max_speed_hz = DIV_ROUND_UP(clksrc, ops->min_div); 1340 ctlr->flags = ops->flags; 1341 ctlr->dev.of_node = pdev->dev.of_node; 1342 ctlr->use_gpio_descriptors = true; 1343 ctlr->max_native_cs = rspi->ops->num_hw_ss; 1344 1345 ret = platform_get_irq_byname_optional(pdev, "rx"); 1346 if (ret < 0) { 1347 ret = platform_get_irq_byname_optional(pdev, "mux"); 1348 if (ret < 0) 1349 ret = platform_get_irq(pdev, 0); 1350 if (ret >= 0) 1351 rspi->rx_irq = rspi->tx_irq = ret; 1352 } else { 1353 rspi->rx_irq = ret; 1354 ret = platform_get_irq_byname(pdev, "tx"); 1355 if (ret >= 0) 1356 rspi->tx_irq = ret; 1357 } 1358 1359 if (rspi->rx_irq == rspi->tx_irq) { 1360 /* Single multiplexed interrupt */ 1361 ret = rspi_request_irq(&pdev->dev, rspi->rx_irq, rspi_irq_mux, 1362 "mux", rspi); 1363 } else { 1364 /* Multi-interrupt mode, only SPRI and SPTI are used */ 1365 ret = rspi_request_irq(&pdev->dev, rspi->rx_irq, rspi_irq_rx, 1366 "rx", rspi); 1367 if (!ret) 1368 ret = rspi_request_irq(&pdev->dev, rspi->tx_irq, 1369 rspi_irq_tx, "tx", rspi); 1370 } 1371 if (ret < 0) { 1372 dev_err(&pdev->dev, "request_irq error\n"); 1373 goto error2; 1374 } 1375 1376 ret = rspi_request_dma(&pdev->dev, ctlr, res); 1377 if (ret < 0) 1378 dev_warn(&pdev->dev, "DMA not available, using PIO\n"); 1379 1380 ret = devm_spi_register_controller(&pdev->dev, ctlr); 1381 if (ret < 0) { 1382 dev_err(&pdev->dev, "devm_spi_register_controller error.\n"); 1383 goto error3; 1384 } 1385 1386 dev_info(&pdev->dev, "probed\n"); 1387 1388 return 0; 1389 1390 error3: 1391 rspi_release_dma(ctlr); 1392 error2: 1393 pm_runtime_disable(&pdev->dev); 1394 error1: 1395 spi_controller_put(ctlr); 1396 1397 return ret; 1398 } 1399 1400 static const struct platform_device_id spi_driver_ids[] = { 1401 { "rspi", (kernel_ulong_t)&rspi_ops }, 1402 {}, 1403 }; 1404 1405 MODULE_DEVICE_TABLE(platform, spi_driver_ids); 1406 1407 #ifdef CONFIG_PM_SLEEP 1408 static int rspi_suspend(struct device *dev) 1409 { 1410 struct rspi_data *rspi = dev_get_drvdata(dev); 1411 1412 return spi_controller_suspend(rspi->ctlr); 1413 } 1414 1415 static int rspi_resume(struct device *dev) 1416 { 1417 struct rspi_data *rspi = dev_get_drvdata(dev); 1418 1419 return spi_controller_resume(rspi->ctlr); 1420 } 1421 1422 static SIMPLE_DEV_PM_OPS(rspi_pm_ops, rspi_suspend, rspi_resume); 1423 #define DEV_PM_OPS &rspi_pm_ops 1424 #else 1425 #define DEV_PM_OPS NULL 1426 #endif /* CONFIG_PM_SLEEP */ 1427 1428 static struct platform_driver rspi_driver = { 1429 .probe = rspi_probe, 1430 .remove = rspi_remove, 1431 .id_table = spi_driver_ids, 1432 .driver = { 1433 .name = "renesas_spi", 1434 .pm = DEV_PM_OPS, 1435 .of_match_table = of_match_ptr(rspi_of_match), 1436 }, 1437 }; 1438 module_platform_driver(rspi_driver); 1439 1440 MODULE_DESCRIPTION("Renesas RSPI bus driver"); 1441 MODULE_LICENSE("GPL v2"); 1442 MODULE_AUTHOR("Yoshihiro Shimoda"); 1443