xref: /linux/drivers/spi/spi-pic32.c (revision fd639726bf15fca8ee1a00dce8e0096d0ad9bd18)
1 /*
2  * Microchip PIC32 SPI controller driver.
3  *
4  * Purna Chandra Mandal <purna.mandal@microchip.com>
5  * Copyright (c) 2016, Microchip Technology Inc.
6  *
7  * This program is free software; you can distribute it and/or modify it
8  * under the terms of the GNU General Public License (Version 2) as
9  * published by the Free Software Foundation.
10  *
11  * This program is distributed in the hope it will be useful, but WITHOUT
12  * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
13  * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
14  * for more details.
15  */
16 
17 #include <linux/clk.h>
18 #include <linux/clkdev.h>
19 #include <linux/delay.h>
20 #include <linux/dmaengine.h>
21 #include <linux/dma-mapping.h>
22 #include <linux/highmem.h>
23 #include <linux/module.h>
24 #include <linux/io.h>
25 #include <linux/interrupt.h>
26 #include <linux/of.h>
27 #include <linux/of_irq.h>
28 #include <linux/of_gpio.h>
29 #include <linux/of_address.h>
30 #include <linux/platform_device.h>
31 #include <linux/spi/spi.h>
32 
33 /* SPI controller registers */
34 struct pic32_spi_regs {
35 	u32 ctrl;
36 	u32 ctrl_clr;
37 	u32 ctrl_set;
38 	u32 ctrl_inv;
39 	u32 status;
40 	u32 status_clr;
41 	u32 status_set;
42 	u32 status_inv;
43 	u32 buf;
44 	u32 dontuse[3];
45 	u32 baud;
46 	u32 dontuse2[3];
47 	u32 ctrl2;
48 	u32 ctrl2_clr;
49 	u32 ctrl2_set;
50 	u32 ctrl2_inv;
51 };
52 
53 /* Bit fields of SPI Control Register */
54 #define CTRL_RX_INT_SHIFT	0  /* Rx interrupt generation */
55 #define  RX_FIFO_EMPTY		0
56 #define  RX_FIFO_NOT_EMPTY	1 /* not empty */
57 #define  RX_FIFO_HALF_FULL	2 /* full by half or more */
58 #define  RX_FIFO_FULL		3 /* completely full */
59 
60 #define CTRL_TX_INT_SHIFT	2  /* TX interrupt generation */
61 #define  TX_FIFO_ALL_EMPTY	0 /* completely empty */
62 #define  TX_FIFO_EMPTY		1 /* empty */
63 #define  TX_FIFO_HALF_EMPTY	2 /* empty by half or more */
64 #define  TX_FIFO_NOT_FULL	3 /* atleast one empty */
65 
66 #define CTRL_MSTEN	BIT(5) /* enable master mode */
67 #define CTRL_CKP	BIT(6) /* active low */
68 #define CTRL_CKE	BIT(8) /* Tx on falling edge */
69 #define CTRL_SMP	BIT(9) /* Rx at middle or end of tx */
70 #define CTRL_BPW_MASK	0x03   /* bits per word/sample */
71 #define CTRL_BPW_SHIFT	10
72 #define  PIC32_BPW_8	0
73 #define  PIC32_BPW_16	1
74 #define  PIC32_BPW_32	2
75 #define CTRL_SIDL	BIT(13) /* sleep when idle */
76 #define CTRL_ON		BIT(15) /* enable macro */
77 #define CTRL_ENHBUF	BIT(16) /* enable enhanced buffering */
78 #define CTRL_MCLKSEL	BIT(23) /* select clock source */
79 #define CTRL_MSSEN	BIT(28) /* macro driven /SS */
80 #define CTRL_FRMEN	BIT(31) /* enable framing mode */
81 
82 /* Bit fields of SPI Status Register */
83 #define STAT_RF_EMPTY	BIT(5) /* RX Fifo empty */
84 #define STAT_RX_OV	BIT(6) /* err, s/w needs to clear */
85 #define STAT_TX_UR	BIT(8) /* UR in Framed SPI modes */
86 #define STAT_FRM_ERR	BIT(12) /* Multiple Frame Sync pulse */
87 #define STAT_TF_LVL_MASK	0x1F
88 #define STAT_TF_LVL_SHIFT	16
89 #define STAT_RF_LVL_MASK	0x1F
90 #define STAT_RF_LVL_SHIFT	24
91 
92 /* Bit fields of SPI Baud Register */
93 #define BAUD_MASK		0x1ff
94 
95 /* Bit fields of SPI Control2 Register */
96 #define CTRL2_TX_UR_EN		BIT(10) /* Enable int on Tx under-run */
97 #define CTRL2_RX_OV_EN		BIT(11) /* Enable int on Rx over-run */
98 #define CTRL2_FRM_ERR_EN	BIT(12) /* Enable frame err int */
99 
100 /* Minimum DMA transfer size */
101 #define PIC32_DMA_LEN_MIN	64
102 
103 struct pic32_spi {
104 	dma_addr_t		dma_base;
105 	struct pic32_spi_regs __iomem *regs;
106 	int			fault_irq;
107 	int			rx_irq;
108 	int			tx_irq;
109 	u32			fifo_n_byte; /* FIFO depth in bytes */
110 	struct clk		*clk;
111 	struct spi_master	*master;
112 	/* Current controller setting */
113 	u32			speed_hz; /* spi-clk rate */
114 	u32			mode;
115 	u32			bits_per_word;
116 	u32			fifo_n_elm; /* FIFO depth in words */
117 #define PIC32F_DMA_PREP		0 /* DMA chnls configured */
118 	unsigned long		flags;
119 	/* Current transfer state */
120 	struct completion	xfer_done;
121 	/* PIO transfer specific */
122 	const void		*tx;
123 	const void		*tx_end;
124 	const void		*rx;
125 	const void		*rx_end;
126 	int			len;
127 	void (*rx_fifo)(struct pic32_spi *);
128 	void (*tx_fifo)(struct pic32_spi *);
129 };
130 
131 static inline void pic32_spi_enable(struct pic32_spi *pic32s)
132 {
133 	writel(CTRL_ON | CTRL_SIDL, &pic32s->regs->ctrl_set);
134 }
135 
136 static inline void pic32_spi_disable(struct pic32_spi *pic32s)
137 {
138 	writel(CTRL_ON | CTRL_SIDL, &pic32s->regs->ctrl_clr);
139 
140 	/* avoid SPI registers read/write at immediate next CPU clock */
141 	ndelay(20);
142 }
143 
144 static void pic32_spi_set_clk_rate(struct pic32_spi *pic32s, u32 spi_ck)
145 {
146 	u32 div;
147 
148 	/* div = (clk_in / 2 * spi_ck) - 1 */
149 	div = DIV_ROUND_CLOSEST(clk_get_rate(pic32s->clk), 2 * spi_ck) - 1;
150 
151 	writel(div & BAUD_MASK, &pic32s->regs->baud);
152 }
153 
154 static inline u32 pic32_rx_fifo_level(struct pic32_spi *pic32s)
155 {
156 	u32 sr = readl(&pic32s->regs->status);
157 
158 	return (sr >> STAT_RF_LVL_SHIFT) & STAT_RF_LVL_MASK;
159 }
160 
161 static inline u32 pic32_tx_fifo_level(struct pic32_spi *pic32s)
162 {
163 	u32 sr = readl(&pic32s->regs->status);
164 
165 	return (sr >> STAT_TF_LVL_SHIFT) & STAT_TF_LVL_MASK;
166 }
167 
168 /* Return the max entries we can fill into tx fifo */
169 static u32 pic32_tx_max(struct pic32_spi *pic32s, int n_bytes)
170 {
171 	u32 tx_left, tx_room, rxtx_gap;
172 
173 	tx_left = (pic32s->tx_end - pic32s->tx) / n_bytes;
174 	tx_room = pic32s->fifo_n_elm - pic32_tx_fifo_level(pic32s);
175 
176 	/*
177 	 * Another concern is about the tx/rx mismatch, we
178 	 * though to use (pic32s->fifo_n_byte - rxfl - txfl) as
179 	 * one maximum value for tx, but it doesn't cover the
180 	 * data which is out of tx/rx fifo and inside the
181 	 * shift registers. So a ctrl from sw point of
182 	 * view is taken.
183 	 */
184 	rxtx_gap = ((pic32s->rx_end - pic32s->rx) -
185 		    (pic32s->tx_end - pic32s->tx)) / n_bytes;
186 	return min3(tx_left, tx_room, (u32)(pic32s->fifo_n_elm - rxtx_gap));
187 }
188 
189 /* Return the max entries we should read out of rx fifo */
190 static u32 pic32_rx_max(struct pic32_spi *pic32s, int n_bytes)
191 {
192 	u32 rx_left = (pic32s->rx_end - pic32s->rx) / n_bytes;
193 
194 	return min_t(u32, rx_left, pic32_rx_fifo_level(pic32s));
195 }
196 
197 #define BUILD_SPI_FIFO_RW(__name, __type, __bwl)		\
198 static void pic32_spi_rx_##__name(struct pic32_spi *pic32s)	\
199 {								\
200 	__type v;						\
201 	u32 mx = pic32_rx_max(pic32s, sizeof(__type));		\
202 	for (; mx; mx--) {					\
203 		v = read##__bwl(&pic32s->regs->buf);		\
204 		if (pic32s->rx_end - pic32s->len)		\
205 			*(__type *)(pic32s->rx) = v;		\
206 		pic32s->rx += sizeof(__type);			\
207 	}							\
208 }								\
209 								\
210 static void pic32_spi_tx_##__name(struct pic32_spi *pic32s)	\
211 {								\
212 	__type v;						\
213 	u32 mx = pic32_tx_max(pic32s, sizeof(__type));		\
214 	for (; mx ; mx--) {					\
215 		v = (__type)~0U;				\
216 		if (pic32s->tx_end - pic32s->len)		\
217 			v = *(__type *)(pic32s->tx);		\
218 		write##__bwl(v, &pic32s->regs->buf);		\
219 		pic32s->tx += sizeof(__type);			\
220 	}							\
221 }
222 
223 BUILD_SPI_FIFO_RW(byte, u8, b);
224 BUILD_SPI_FIFO_RW(word, u16, w);
225 BUILD_SPI_FIFO_RW(dword, u32, l);
226 
227 static void pic32_err_stop(struct pic32_spi *pic32s, const char *msg)
228 {
229 	/* disable all interrupts */
230 	disable_irq_nosync(pic32s->fault_irq);
231 	disable_irq_nosync(pic32s->rx_irq);
232 	disable_irq_nosync(pic32s->tx_irq);
233 
234 	/* Show err message and abort xfer with err */
235 	dev_err(&pic32s->master->dev, "%s\n", msg);
236 	if (pic32s->master->cur_msg)
237 		pic32s->master->cur_msg->status = -EIO;
238 	complete(&pic32s->xfer_done);
239 }
240 
241 static irqreturn_t pic32_spi_fault_irq(int irq, void *dev_id)
242 {
243 	struct pic32_spi *pic32s = dev_id;
244 	u32 status;
245 
246 	status = readl(&pic32s->regs->status);
247 
248 	/* Error handling */
249 	if (status & (STAT_RX_OV | STAT_TX_UR)) {
250 		writel(STAT_RX_OV, &pic32s->regs->status_clr);
251 		writel(STAT_TX_UR, &pic32s->regs->status_clr);
252 		pic32_err_stop(pic32s, "err_irq: fifo ov/ur-run\n");
253 		return IRQ_HANDLED;
254 	}
255 
256 	if (status & STAT_FRM_ERR) {
257 		pic32_err_stop(pic32s, "err_irq: frame error");
258 		return IRQ_HANDLED;
259 	}
260 
261 	if (!pic32s->master->cur_msg) {
262 		pic32_err_stop(pic32s, "err_irq: no mesg");
263 		return IRQ_NONE;
264 	}
265 
266 	return IRQ_NONE;
267 }
268 
269 static irqreturn_t pic32_spi_rx_irq(int irq, void *dev_id)
270 {
271 	struct pic32_spi *pic32s = dev_id;
272 
273 	pic32s->rx_fifo(pic32s);
274 
275 	/* rx complete ? */
276 	if (pic32s->rx_end == pic32s->rx) {
277 		/* disable all interrupts */
278 		disable_irq_nosync(pic32s->fault_irq);
279 		disable_irq_nosync(pic32s->rx_irq);
280 
281 		/* complete current xfer */
282 		complete(&pic32s->xfer_done);
283 	}
284 
285 	return IRQ_HANDLED;
286 }
287 
288 static irqreturn_t pic32_spi_tx_irq(int irq, void *dev_id)
289 {
290 	struct pic32_spi *pic32s = dev_id;
291 
292 	pic32s->tx_fifo(pic32s);
293 
294 	/* tx complete? disable tx interrupt */
295 	if (pic32s->tx_end == pic32s->tx)
296 		disable_irq_nosync(pic32s->tx_irq);
297 
298 	return IRQ_HANDLED;
299 }
300 
301 static void pic32_spi_dma_rx_notify(void *data)
302 {
303 	struct pic32_spi *pic32s = data;
304 
305 	complete(&pic32s->xfer_done);
306 }
307 
308 static int pic32_spi_dma_transfer(struct pic32_spi *pic32s,
309 				  struct spi_transfer *xfer)
310 {
311 	struct spi_master *master = pic32s->master;
312 	struct dma_async_tx_descriptor *desc_rx;
313 	struct dma_async_tx_descriptor *desc_tx;
314 	dma_cookie_t cookie;
315 	int ret;
316 
317 	if (!master->dma_rx || !master->dma_tx)
318 		return -ENODEV;
319 
320 	desc_rx = dmaengine_prep_slave_sg(master->dma_rx,
321 					  xfer->rx_sg.sgl,
322 					  xfer->rx_sg.nents,
323 					  DMA_FROM_DEVICE,
324 					  DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
325 	if (!desc_rx) {
326 		ret = -EINVAL;
327 		goto err_dma;
328 	}
329 
330 	desc_tx = dmaengine_prep_slave_sg(master->dma_tx,
331 					  xfer->tx_sg.sgl,
332 					  xfer->tx_sg.nents,
333 					  DMA_TO_DEVICE,
334 					  DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
335 	if (!desc_tx) {
336 		ret = -EINVAL;
337 		goto err_dma;
338 	}
339 
340 	/* Put callback on the RX transfer, that should finish last */
341 	desc_rx->callback = pic32_spi_dma_rx_notify;
342 	desc_rx->callback_param = pic32s;
343 
344 	cookie = dmaengine_submit(desc_rx);
345 	ret = dma_submit_error(cookie);
346 	if (ret)
347 		goto err_dma;
348 
349 	cookie = dmaengine_submit(desc_tx);
350 	ret = dma_submit_error(cookie);
351 	if (ret)
352 		goto err_dma_tx;
353 
354 	dma_async_issue_pending(master->dma_rx);
355 	dma_async_issue_pending(master->dma_tx);
356 
357 	return 0;
358 
359 err_dma_tx:
360 	dmaengine_terminate_all(master->dma_rx);
361 err_dma:
362 	return ret;
363 }
364 
365 static int pic32_spi_dma_config(struct pic32_spi *pic32s, u32 dma_width)
366 {
367 	int buf_offset = offsetof(struct pic32_spi_regs, buf);
368 	struct spi_master *master = pic32s->master;
369 	struct dma_slave_config cfg;
370 	int ret;
371 
372 	cfg.device_fc = true;
373 	cfg.src_addr = pic32s->dma_base + buf_offset;
374 	cfg.dst_addr = pic32s->dma_base + buf_offset;
375 	cfg.src_maxburst = pic32s->fifo_n_elm / 2; /* fill one-half */
376 	cfg.dst_maxburst = pic32s->fifo_n_elm / 2; /* drain one-half */
377 	cfg.src_addr_width = dma_width;
378 	cfg.dst_addr_width = dma_width;
379 	/* tx channel */
380 	cfg.slave_id = pic32s->tx_irq;
381 	cfg.direction = DMA_MEM_TO_DEV;
382 	ret = dmaengine_slave_config(master->dma_tx, &cfg);
383 	if (ret) {
384 		dev_err(&master->dev, "tx channel setup failed\n");
385 		return ret;
386 	}
387 	/* rx channel */
388 	cfg.slave_id = pic32s->rx_irq;
389 	cfg.direction = DMA_DEV_TO_MEM;
390 	ret = dmaengine_slave_config(master->dma_rx, &cfg);
391 	if (ret)
392 		dev_err(&master->dev, "rx channel setup failed\n");
393 
394 	return ret;
395 }
396 
397 static int pic32_spi_set_word_size(struct pic32_spi *pic32s, u8 bits_per_word)
398 {
399 	enum dma_slave_buswidth dmawidth;
400 	u32 buswidth, v;
401 
402 	switch (bits_per_word) {
403 	case 8:
404 		pic32s->rx_fifo = pic32_spi_rx_byte;
405 		pic32s->tx_fifo = pic32_spi_tx_byte;
406 		buswidth = PIC32_BPW_8;
407 		dmawidth = DMA_SLAVE_BUSWIDTH_1_BYTE;
408 		break;
409 	case 16:
410 		pic32s->rx_fifo = pic32_spi_rx_word;
411 		pic32s->tx_fifo = pic32_spi_tx_word;
412 		buswidth = PIC32_BPW_16;
413 		dmawidth = DMA_SLAVE_BUSWIDTH_2_BYTES;
414 		break;
415 	case 32:
416 		pic32s->rx_fifo = pic32_spi_rx_dword;
417 		pic32s->tx_fifo = pic32_spi_tx_dword;
418 		buswidth = PIC32_BPW_32;
419 		dmawidth = DMA_SLAVE_BUSWIDTH_4_BYTES;
420 		break;
421 	default:
422 		/* not supported */
423 		return -EINVAL;
424 	}
425 
426 	/* calculate maximum number of words fifos can hold */
427 	pic32s->fifo_n_elm = DIV_ROUND_UP(pic32s->fifo_n_byte,
428 					  bits_per_word / 8);
429 	/* set word size */
430 	v = readl(&pic32s->regs->ctrl);
431 	v &= ~(CTRL_BPW_MASK << CTRL_BPW_SHIFT);
432 	v |= buswidth << CTRL_BPW_SHIFT;
433 	writel(v, &pic32s->regs->ctrl);
434 
435 	/* re-configure dma width, if required */
436 	if (test_bit(PIC32F_DMA_PREP, &pic32s->flags))
437 		pic32_spi_dma_config(pic32s, dmawidth);
438 
439 	return 0;
440 }
441 
442 static int pic32_spi_prepare_hardware(struct spi_master *master)
443 {
444 	struct pic32_spi *pic32s = spi_master_get_devdata(master);
445 
446 	pic32_spi_enable(pic32s);
447 
448 	return 0;
449 }
450 
451 static int pic32_spi_prepare_message(struct spi_master *master,
452 				     struct spi_message *msg)
453 {
454 	struct pic32_spi *pic32s = spi_master_get_devdata(master);
455 	struct spi_device *spi = msg->spi;
456 	u32 val;
457 
458 	/* set device specific bits_per_word */
459 	if (pic32s->bits_per_word != spi->bits_per_word) {
460 		pic32_spi_set_word_size(pic32s, spi->bits_per_word);
461 		pic32s->bits_per_word = spi->bits_per_word;
462 	}
463 
464 	/* device specific speed change */
465 	if (pic32s->speed_hz != spi->max_speed_hz) {
466 		pic32_spi_set_clk_rate(pic32s, spi->max_speed_hz);
467 		pic32s->speed_hz = spi->max_speed_hz;
468 	}
469 
470 	/* device specific mode change */
471 	if (pic32s->mode != spi->mode) {
472 		val = readl(&pic32s->regs->ctrl);
473 		/* active low */
474 		if (spi->mode & SPI_CPOL)
475 			val |= CTRL_CKP;
476 		else
477 			val &= ~CTRL_CKP;
478 		/* tx on rising edge */
479 		if (spi->mode & SPI_CPHA)
480 			val &= ~CTRL_CKE;
481 		else
482 			val |= CTRL_CKE;
483 
484 		/* rx at end of tx */
485 		val |= CTRL_SMP;
486 		writel(val, &pic32s->regs->ctrl);
487 		pic32s->mode = spi->mode;
488 	}
489 
490 	return 0;
491 }
492 
493 static bool pic32_spi_can_dma(struct spi_master *master,
494 			      struct spi_device *spi,
495 			      struct spi_transfer *xfer)
496 {
497 	struct pic32_spi *pic32s = spi_master_get_devdata(master);
498 
499 	/* skip using DMA on small size transfer to avoid overhead.*/
500 	return (xfer->len >= PIC32_DMA_LEN_MIN) &&
501 	       test_bit(PIC32F_DMA_PREP, &pic32s->flags);
502 }
503 
504 static int pic32_spi_one_transfer(struct spi_master *master,
505 				  struct spi_device *spi,
506 				  struct spi_transfer *transfer)
507 {
508 	struct pic32_spi *pic32s;
509 	bool dma_issued = false;
510 	unsigned long timeout;
511 	int ret;
512 
513 	pic32s = spi_master_get_devdata(master);
514 
515 	/* handle transfer specific word size change */
516 	if (transfer->bits_per_word &&
517 	    (transfer->bits_per_word != pic32s->bits_per_word)) {
518 		ret = pic32_spi_set_word_size(pic32s, transfer->bits_per_word);
519 		if (ret)
520 			return ret;
521 		pic32s->bits_per_word = transfer->bits_per_word;
522 	}
523 
524 	/* handle transfer specific speed change */
525 	if (transfer->speed_hz && (transfer->speed_hz != pic32s->speed_hz)) {
526 		pic32_spi_set_clk_rate(pic32s, transfer->speed_hz);
527 		pic32s->speed_hz = transfer->speed_hz;
528 	}
529 
530 	reinit_completion(&pic32s->xfer_done);
531 
532 	/* transact by DMA mode */
533 	if (transfer->rx_sg.nents && transfer->tx_sg.nents) {
534 		ret = pic32_spi_dma_transfer(pic32s, transfer);
535 		if (ret) {
536 			dev_err(&spi->dev, "dma submit error\n");
537 			return ret;
538 		}
539 
540 		/* DMA issued */
541 		dma_issued = true;
542 	} else {
543 		/* set current transfer information */
544 		pic32s->tx = (const void *)transfer->tx_buf;
545 		pic32s->rx = (const void *)transfer->rx_buf;
546 		pic32s->tx_end = pic32s->tx + transfer->len;
547 		pic32s->rx_end = pic32s->rx + transfer->len;
548 		pic32s->len = transfer->len;
549 
550 		/* transact by interrupt driven PIO */
551 		enable_irq(pic32s->fault_irq);
552 		enable_irq(pic32s->rx_irq);
553 		enable_irq(pic32s->tx_irq);
554 	}
555 
556 	/* wait for completion */
557 	timeout = wait_for_completion_timeout(&pic32s->xfer_done, 2 * HZ);
558 	if (timeout == 0) {
559 		dev_err(&spi->dev, "wait error/timedout\n");
560 		if (dma_issued) {
561 			dmaengine_terminate_all(master->dma_rx);
562 			dmaengine_terminate_all(master->dma_rx);
563 		}
564 		ret = -ETIMEDOUT;
565 	} else {
566 		ret = 0;
567 	}
568 
569 	return ret;
570 }
571 
572 static int pic32_spi_unprepare_message(struct spi_master *master,
573 				       struct spi_message *msg)
574 {
575 	/* nothing to do */
576 	return 0;
577 }
578 
579 static int pic32_spi_unprepare_hardware(struct spi_master *master)
580 {
581 	struct pic32_spi *pic32s = spi_master_get_devdata(master);
582 
583 	pic32_spi_disable(pic32s);
584 
585 	return 0;
586 }
587 
588 /* This may be called multiple times by same spi dev */
589 static int pic32_spi_setup(struct spi_device *spi)
590 {
591 	if (!spi->max_speed_hz) {
592 		dev_err(&spi->dev, "No max speed HZ parameter\n");
593 		return -EINVAL;
594 	}
595 
596 	/* PIC32 spi controller can drive /CS during transfer depending
597 	 * on tx fifo fill-level. /CS will stay asserted as long as TX
598 	 * fifo is non-empty, else will be deasserted indicating
599 	 * completion of the ongoing transfer. This might result into
600 	 * unreliable/erroneous SPI transactions.
601 	 * To avoid that we will always handle /CS by toggling GPIO.
602 	 */
603 	if (!gpio_is_valid(spi->cs_gpio))
604 		return -EINVAL;
605 
606 	gpio_direction_output(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
607 
608 	return 0;
609 }
610 
611 static void pic32_spi_cleanup(struct spi_device *spi)
612 {
613 	/* de-activate cs-gpio */
614 	gpio_direction_output(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
615 }
616 
617 static void pic32_spi_dma_prep(struct pic32_spi *pic32s, struct device *dev)
618 {
619 	struct spi_master *master = pic32s->master;
620 	dma_cap_mask_t mask;
621 
622 	dma_cap_zero(mask);
623 	dma_cap_set(DMA_SLAVE, mask);
624 
625 	master->dma_rx = dma_request_slave_channel_compat(mask, NULL, NULL,
626 							  dev, "spi-rx");
627 	if (!master->dma_rx) {
628 		dev_warn(dev, "RX channel not found.\n");
629 		goto out_err;
630 	}
631 
632 	master->dma_tx = dma_request_slave_channel_compat(mask, NULL, NULL,
633 							  dev, "spi-tx");
634 	if (!master->dma_tx) {
635 		dev_warn(dev, "TX channel not found.\n");
636 		goto out_err;
637 	}
638 
639 	if (pic32_spi_dma_config(pic32s, DMA_SLAVE_BUSWIDTH_1_BYTE))
640 		goto out_err;
641 
642 	/* DMA chnls allocated and prepared */
643 	set_bit(PIC32F_DMA_PREP, &pic32s->flags);
644 
645 	return;
646 
647 out_err:
648 	if (master->dma_rx)
649 		dma_release_channel(master->dma_rx);
650 
651 	if (master->dma_tx)
652 		dma_release_channel(master->dma_tx);
653 }
654 
655 static void pic32_spi_dma_unprep(struct pic32_spi *pic32s)
656 {
657 	if (!test_bit(PIC32F_DMA_PREP, &pic32s->flags))
658 		return;
659 
660 	clear_bit(PIC32F_DMA_PREP, &pic32s->flags);
661 	if (pic32s->master->dma_rx)
662 		dma_release_channel(pic32s->master->dma_rx);
663 
664 	if (pic32s->master->dma_tx)
665 		dma_release_channel(pic32s->master->dma_tx);
666 }
667 
668 static void pic32_spi_hw_init(struct pic32_spi *pic32s)
669 {
670 	u32 ctrl;
671 
672 	/* disable hardware */
673 	pic32_spi_disable(pic32s);
674 
675 	ctrl = readl(&pic32s->regs->ctrl);
676 	/* enable enhanced fifo of 128bit deep */
677 	ctrl |= CTRL_ENHBUF;
678 	pic32s->fifo_n_byte = 16;
679 
680 	/* disable framing mode */
681 	ctrl &= ~CTRL_FRMEN;
682 
683 	/* enable master mode while disabled */
684 	ctrl |= CTRL_MSTEN;
685 
686 	/* set tx fifo threshold interrupt */
687 	ctrl &= ~(0x3 << CTRL_TX_INT_SHIFT);
688 	ctrl |= (TX_FIFO_HALF_EMPTY << CTRL_TX_INT_SHIFT);
689 
690 	/* set rx fifo threshold interrupt */
691 	ctrl &= ~(0x3 << CTRL_RX_INT_SHIFT);
692 	ctrl |= (RX_FIFO_NOT_EMPTY << CTRL_RX_INT_SHIFT);
693 
694 	/* select clk source */
695 	ctrl &= ~CTRL_MCLKSEL;
696 
697 	/* set manual /CS mode */
698 	ctrl &= ~CTRL_MSSEN;
699 
700 	writel(ctrl, &pic32s->regs->ctrl);
701 
702 	/* enable error reporting */
703 	ctrl = CTRL2_TX_UR_EN | CTRL2_RX_OV_EN | CTRL2_FRM_ERR_EN;
704 	writel(ctrl, &pic32s->regs->ctrl2_set);
705 }
706 
707 static int pic32_spi_hw_probe(struct platform_device *pdev,
708 			      struct pic32_spi *pic32s)
709 {
710 	struct resource *mem;
711 	int ret;
712 
713 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
714 	pic32s->regs = devm_ioremap_resource(&pdev->dev, mem);
715 	if (IS_ERR(pic32s->regs))
716 		return PTR_ERR(pic32s->regs);
717 
718 	pic32s->dma_base = mem->start;
719 
720 	/* get irq resources: err-irq, rx-irq, tx-irq */
721 	pic32s->fault_irq = platform_get_irq_byname(pdev, "fault");
722 	if (pic32s->fault_irq < 0) {
723 		dev_err(&pdev->dev, "fault-irq not found\n");
724 		return pic32s->fault_irq;
725 	}
726 
727 	pic32s->rx_irq = platform_get_irq_byname(pdev, "rx");
728 	if (pic32s->rx_irq < 0) {
729 		dev_err(&pdev->dev, "rx-irq not found\n");
730 		return pic32s->rx_irq;
731 	}
732 
733 	pic32s->tx_irq = platform_get_irq_byname(pdev, "tx");
734 	if (pic32s->tx_irq < 0) {
735 		dev_err(&pdev->dev, "tx-irq not found\n");
736 		return pic32s->tx_irq;
737 	}
738 
739 	/* get clock */
740 	pic32s->clk = devm_clk_get(&pdev->dev, "mck0");
741 	if (IS_ERR(pic32s->clk)) {
742 		dev_err(&pdev->dev, "clk not found\n");
743 		ret = PTR_ERR(pic32s->clk);
744 		goto err_unmap_mem;
745 	}
746 
747 	ret = clk_prepare_enable(pic32s->clk);
748 	if (ret)
749 		goto err_unmap_mem;
750 
751 	pic32_spi_hw_init(pic32s);
752 
753 	return 0;
754 
755 err_unmap_mem:
756 	dev_err(&pdev->dev, "%s failed, err %d\n", __func__, ret);
757 	return ret;
758 }
759 
760 static int pic32_spi_probe(struct platform_device *pdev)
761 {
762 	struct spi_master *master;
763 	struct pic32_spi *pic32s;
764 	int ret;
765 
766 	master = spi_alloc_master(&pdev->dev, sizeof(*pic32s));
767 	if (!master)
768 		return -ENOMEM;
769 
770 	pic32s = spi_master_get_devdata(master);
771 	pic32s->master = master;
772 
773 	ret = pic32_spi_hw_probe(pdev, pic32s);
774 	if (ret)
775 		goto err_master;
776 
777 	master->dev.of_node	= of_node_get(pdev->dev.of_node);
778 	master->mode_bits	= SPI_MODE_3 | SPI_MODE_0 | SPI_CS_HIGH;
779 	master->num_chipselect	= 1; /* single chip-select */
780 	master->max_speed_hz	= clk_get_rate(pic32s->clk);
781 	master->setup		= pic32_spi_setup;
782 	master->cleanup		= pic32_spi_cleanup;
783 	master->flags		= SPI_MASTER_MUST_TX | SPI_MASTER_MUST_RX;
784 	master->bits_per_word_mask	= SPI_BPW_MASK(8) | SPI_BPW_MASK(16) |
785 					  SPI_BPW_MASK(32);
786 	master->transfer_one		= pic32_spi_one_transfer;
787 	master->prepare_message		= pic32_spi_prepare_message;
788 	master->unprepare_message	= pic32_spi_unprepare_message;
789 	master->prepare_transfer_hardware	= pic32_spi_prepare_hardware;
790 	master->unprepare_transfer_hardware	= pic32_spi_unprepare_hardware;
791 
792 	/* optional DMA support */
793 	pic32_spi_dma_prep(pic32s, &pdev->dev);
794 	if (test_bit(PIC32F_DMA_PREP, &pic32s->flags))
795 		master->can_dma	= pic32_spi_can_dma;
796 
797 	init_completion(&pic32s->xfer_done);
798 	pic32s->mode = -1;
799 
800 	/* install irq handlers (with irq-disabled) */
801 	irq_set_status_flags(pic32s->fault_irq, IRQ_NOAUTOEN);
802 	ret = devm_request_irq(&pdev->dev, pic32s->fault_irq,
803 			       pic32_spi_fault_irq, IRQF_NO_THREAD,
804 			       dev_name(&pdev->dev), pic32s);
805 	if (ret < 0) {
806 		dev_err(&pdev->dev, "request fault-irq %d\n", pic32s->rx_irq);
807 		goto err_bailout;
808 	}
809 
810 	/* receive interrupt handler */
811 	irq_set_status_flags(pic32s->rx_irq, IRQ_NOAUTOEN);
812 	ret = devm_request_irq(&pdev->dev, pic32s->rx_irq,
813 			       pic32_spi_rx_irq, IRQF_NO_THREAD,
814 			       dev_name(&pdev->dev), pic32s);
815 	if (ret < 0) {
816 		dev_err(&pdev->dev, "request rx-irq %d\n", pic32s->rx_irq);
817 		goto err_bailout;
818 	}
819 
820 	/* transmit interrupt handler */
821 	irq_set_status_flags(pic32s->tx_irq, IRQ_NOAUTOEN);
822 	ret = devm_request_irq(&pdev->dev, pic32s->tx_irq,
823 			       pic32_spi_tx_irq, IRQF_NO_THREAD,
824 			       dev_name(&pdev->dev), pic32s);
825 	if (ret < 0) {
826 		dev_err(&pdev->dev, "request tx-irq %d\n", pic32s->tx_irq);
827 		goto err_bailout;
828 	}
829 
830 	/* register master */
831 	ret = devm_spi_register_master(&pdev->dev, master);
832 	if (ret) {
833 		dev_err(&master->dev, "failed registering spi master\n");
834 		goto err_bailout;
835 	}
836 
837 	platform_set_drvdata(pdev, pic32s);
838 
839 	return 0;
840 
841 err_bailout:
842 	clk_disable_unprepare(pic32s->clk);
843 err_master:
844 	spi_master_put(master);
845 	return ret;
846 }
847 
848 static int pic32_spi_remove(struct platform_device *pdev)
849 {
850 	struct pic32_spi *pic32s;
851 
852 	pic32s = platform_get_drvdata(pdev);
853 	pic32_spi_disable(pic32s);
854 	clk_disable_unprepare(pic32s->clk);
855 	pic32_spi_dma_unprep(pic32s);
856 
857 	return 0;
858 }
859 
860 static const struct of_device_id pic32_spi_of_match[] = {
861 	{.compatible = "microchip,pic32mzda-spi",},
862 	{},
863 };
864 MODULE_DEVICE_TABLE(of, pic32_spi_of_match);
865 
866 static struct platform_driver pic32_spi_driver = {
867 	.driver = {
868 		.name = "spi-pic32",
869 		.of_match_table = of_match_ptr(pic32_spi_of_match),
870 	},
871 	.probe = pic32_spi_probe,
872 	.remove = pic32_spi_remove,
873 };
874 
875 module_platform_driver(pic32_spi_driver);
876 
877 MODULE_AUTHOR("Purna Chandra Mandal <purna.mandal@microchip.com>");
878 MODULE_DESCRIPTION("Microchip SPI driver for PIC32 SPI controller.");
879 MODULE_LICENSE("GPL v2");
880