1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * PIC32 Quad SPI controller driver. 4 * 5 * Purna Chandra Mandal <purna.mandal@microchip.com> 6 * Copyright (c) 2016, Microchip Technology Inc. 7 */ 8 9 #include <linux/clk.h> 10 #include <linux/dma-mapping.h> 11 #include <linux/interrupt.h> 12 #include <linux/io.h> 13 #include <linux/iopoll.h> 14 #include <linux/module.h> 15 #include <linux/of.h> 16 #include <linux/platform_device.h> 17 #include <linux/slab.h> 18 #include <linux/spi/spi.h> 19 20 /* SQI registers */ 21 #define PESQI_XIP_CONF1_REG 0x00 22 #define PESQI_XIP_CONF2_REG 0x04 23 #define PESQI_CONF_REG 0x08 24 #define PESQI_CTRL_REG 0x0C 25 #define PESQI_CLK_CTRL_REG 0x10 26 #define PESQI_CMD_THRES_REG 0x14 27 #define PESQI_INT_THRES_REG 0x18 28 #define PESQI_INT_ENABLE_REG 0x1C 29 #define PESQI_INT_STAT_REG 0x20 30 #define PESQI_TX_DATA_REG 0x24 31 #define PESQI_RX_DATA_REG 0x28 32 #define PESQI_STAT1_REG 0x2C 33 #define PESQI_STAT2_REG 0x30 34 #define PESQI_BD_CTRL_REG 0x34 35 #define PESQI_BD_CUR_ADDR_REG 0x38 36 #define PESQI_BD_BASE_ADDR_REG 0x40 37 #define PESQI_BD_STAT_REG 0x44 38 #define PESQI_BD_POLL_CTRL_REG 0x48 39 #define PESQI_BD_TX_DMA_STAT_REG 0x4C 40 #define PESQI_BD_RX_DMA_STAT_REG 0x50 41 #define PESQI_THRES_REG 0x54 42 #define PESQI_INT_SIGEN_REG 0x58 43 44 /* PESQI_CONF_REG fields */ 45 #define PESQI_MODE 0x7 46 #define PESQI_MODE_BOOT 0 47 #define PESQI_MODE_PIO 1 48 #define PESQI_MODE_DMA 2 49 #define PESQI_MODE_XIP 3 50 #define PESQI_MODE_SHIFT 0 51 #define PESQI_CPHA BIT(3) 52 #define PESQI_CPOL BIT(4) 53 #define PESQI_LSBF BIT(5) 54 #define PESQI_RXLATCH BIT(7) 55 #define PESQI_SERMODE BIT(8) 56 #define PESQI_WP_EN BIT(9) 57 #define PESQI_HOLD_EN BIT(10) 58 #define PESQI_BURST_EN BIT(12) 59 #define PESQI_CS_CTRL_HW BIT(15) 60 #define PESQI_SOFT_RESET BIT(16) 61 #define PESQI_LANES_SHIFT 20 62 #define PESQI_SINGLE_LANE 0 63 #define PESQI_DUAL_LANE 1 64 #define PESQI_QUAD_LANE 2 65 #define PESQI_CSEN_SHIFT 24 66 #define PESQI_EN BIT(23) 67 68 /* PESQI_CLK_CTRL_REG fields */ 69 #define PESQI_CLK_EN BIT(0) 70 #define PESQI_CLK_STABLE BIT(1) 71 #define PESQI_CLKDIV_SHIFT 8 72 #define PESQI_CLKDIV 0xff 73 74 /* PESQI_INT_THR/CMD_THR_REG */ 75 #define PESQI_TXTHR_MASK 0x1f 76 #define PESQI_TXTHR_SHIFT 8 77 #define PESQI_RXTHR_MASK 0x1f 78 #define PESQI_RXTHR_SHIFT 0 79 80 /* PESQI_INT_EN/INT_STAT/INT_SIG_EN_REG */ 81 #define PESQI_TXEMPTY BIT(0) 82 #define PESQI_TXFULL BIT(1) 83 #define PESQI_TXTHR BIT(2) 84 #define PESQI_RXEMPTY BIT(3) 85 #define PESQI_RXFULL BIT(4) 86 #define PESQI_RXTHR BIT(5) 87 #define PESQI_BDDONE BIT(9) /* BD processing complete */ 88 #define PESQI_PKTCOMP BIT(10) /* packet processing complete */ 89 #define PESQI_DMAERR BIT(11) /* error */ 90 91 /* PESQI_BD_CTRL_REG */ 92 #define PESQI_DMA_EN BIT(0) /* enable DMA engine */ 93 #define PESQI_POLL_EN BIT(1) /* enable polling */ 94 #define PESQI_BDP_START BIT(2) /* start BD processor */ 95 96 /* PESQI controller buffer descriptor */ 97 struct buf_desc { 98 u32 bd_ctrl; /* control */ 99 u32 bd_status; /* reserved */ 100 u32 bd_addr; /* DMA buffer addr */ 101 u32 bd_nextp; /* next item in chain */ 102 }; 103 104 /* bd_ctrl */ 105 #define BD_BUFLEN 0x1ff 106 #define BD_CBD_INT_EN BIT(16) /* Current BD is processed */ 107 #define BD_PKT_INT_EN BIT(17) /* All BDs of PKT processed */ 108 #define BD_LIFM BIT(18) /* last data of pkt */ 109 #define BD_LAST BIT(19) /* end of list */ 110 #define BD_DATA_RECV BIT(20) /* receive data */ 111 #define BD_DDR BIT(21) /* DDR mode */ 112 #define BD_DUAL BIT(22) /* Dual SPI */ 113 #define BD_QUAD BIT(23) /* Quad SPI */ 114 #define BD_LSBF BIT(25) /* LSB First */ 115 #define BD_STAT_CHECK BIT(27) /* Status poll */ 116 #define BD_DEVSEL_SHIFT 28 /* CS */ 117 #define BD_CS_DEASSERT BIT(30) /* de-assert CS after current BD */ 118 #define BD_EN BIT(31) /* BD owned by H/W */ 119 120 /** 121 * struct ring_desc - Representation of SQI ring descriptor 122 * @list: list element to add to free or used list. 123 * @bd: PESQI controller buffer descriptor 124 * @bd_dma: DMA address of PESQI controller buffer descriptor 125 * @xfer_len: transfer length 126 */ 127 struct ring_desc { 128 struct list_head list; 129 struct buf_desc *bd; 130 dma_addr_t bd_dma; 131 u32 xfer_len; 132 }; 133 134 /* Global constants */ 135 #define PESQI_BD_BUF_LEN_MAX 256 136 #define PESQI_BD_COUNT 256 /* max 64KB data per spi message */ 137 138 struct pic32_sqi { 139 void __iomem *regs; 140 struct clk *sys_clk; 141 struct clk *base_clk; /* drives spi clock */ 142 struct spi_controller *host; 143 int irq; 144 struct completion xfer_done; 145 struct ring_desc *ring; 146 void *bd; 147 dma_addr_t bd_dma; 148 struct list_head bd_list_free; /* free */ 149 struct list_head bd_list_used; /* allocated */ 150 struct spi_device *cur_spi; 151 u32 cur_speed; 152 u8 cur_mode; 153 }; 154 155 static inline void pic32_setbits(void __iomem *reg, u32 set) 156 { 157 writel(readl(reg) | set, reg); 158 } 159 160 static inline void pic32_clrbits(void __iomem *reg, u32 clr) 161 { 162 writel(readl(reg) & ~clr, reg); 163 } 164 165 static int pic32_sqi_set_clk_rate(struct pic32_sqi *sqi, u32 sck) 166 { 167 u32 val, div; 168 169 /* div = base_clk / (2 * spi_clk) */ 170 div = clk_get_rate(sqi->base_clk) / (2 * sck); 171 div &= PESQI_CLKDIV; 172 173 val = readl(sqi->regs + PESQI_CLK_CTRL_REG); 174 /* apply new divider */ 175 val &= ~(PESQI_CLK_STABLE | (PESQI_CLKDIV << PESQI_CLKDIV_SHIFT)); 176 val |= div << PESQI_CLKDIV_SHIFT; 177 writel(val, sqi->regs + PESQI_CLK_CTRL_REG); 178 179 /* wait for stability */ 180 return readl_poll_timeout(sqi->regs + PESQI_CLK_CTRL_REG, val, 181 val & PESQI_CLK_STABLE, 1, 5000); 182 } 183 184 static inline void pic32_sqi_enable_int(struct pic32_sqi *sqi) 185 { 186 u32 mask = PESQI_DMAERR | PESQI_BDDONE | PESQI_PKTCOMP; 187 188 writel(mask, sqi->regs + PESQI_INT_ENABLE_REG); 189 /* INT_SIGEN works as interrupt-gate to INTR line */ 190 writel(mask, sqi->regs + PESQI_INT_SIGEN_REG); 191 } 192 193 static inline void pic32_sqi_disable_int(struct pic32_sqi *sqi) 194 { 195 writel(0, sqi->regs + PESQI_INT_ENABLE_REG); 196 writel(0, sqi->regs + PESQI_INT_SIGEN_REG); 197 } 198 199 static irqreturn_t pic32_sqi_isr(int irq, void *dev_id) 200 { 201 struct pic32_sqi *sqi = dev_id; 202 u32 enable, status; 203 204 enable = readl(sqi->regs + PESQI_INT_ENABLE_REG); 205 status = readl(sqi->regs + PESQI_INT_STAT_REG); 206 207 /* check spurious interrupt */ 208 if (!status) 209 return IRQ_NONE; 210 211 if (status & PESQI_DMAERR) { 212 enable = 0; 213 goto irq_done; 214 } 215 216 if (status & PESQI_TXTHR) 217 enable &= ~(PESQI_TXTHR | PESQI_TXFULL | PESQI_TXEMPTY); 218 219 if (status & PESQI_RXTHR) 220 enable &= ~(PESQI_RXTHR | PESQI_RXFULL | PESQI_RXEMPTY); 221 222 if (status & PESQI_BDDONE) 223 enable &= ~PESQI_BDDONE; 224 225 /* packet processing completed */ 226 if (status & PESQI_PKTCOMP) { 227 /* mask all interrupts */ 228 enable = 0; 229 /* complete trasaction */ 230 complete(&sqi->xfer_done); 231 } 232 233 irq_done: 234 /* interrupts are sticky, so mask when handled */ 235 writel(enable, sqi->regs + PESQI_INT_ENABLE_REG); 236 237 return IRQ_HANDLED; 238 } 239 240 static struct ring_desc *ring_desc_get(struct pic32_sqi *sqi) 241 { 242 struct ring_desc *rdesc; 243 244 if (list_empty(&sqi->bd_list_free)) 245 return NULL; 246 247 rdesc = list_first_entry(&sqi->bd_list_free, struct ring_desc, list); 248 list_move_tail(&rdesc->list, &sqi->bd_list_used); 249 return rdesc; 250 } 251 252 static void ring_desc_put(struct pic32_sqi *sqi, struct ring_desc *rdesc) 253 { 254 list_move(&rdesc->list, &sqi->bd_list_free); 255 } 256 257 static int pic32_sqi_one_transfer(struct pic32_sqi *sqi, 258 struct spi_message *mesg, 259 struct spi_transfer *xfer) 260 { 261 struct spi_device *spi = mesg->spi; 262 struct scatterlist *sg, *sgl; 263 struct ring_desc *rdesc; 264 struct buf_desc *bd; 265 int nents, i; 266 u32 bd_ctrl; 267 u32 nbits; 268 269 /* Device selection */ 270 bd_ctrl = spi_get_chipselect(spi, 0) << BD_DEVSEL_SHIFT; 271 272 /* half-duplex: select transfer buffer, direction and lane */ 273 if (xfer->rx_buf) { 274 bd_ctrl |= BD_DATA_RECV; 275 nbits = xfer->rx_nbits; 276 sgl = xfer->rx_sg.sgl; 277 nents = xfer->rx_sg.nents; 278 } else { 279 nbits = xfer->tx_nbits; 280 sgl = xfer->tx_sg.sgl; 281 nents = xfer->tx_sg.nents; 282 } 283 284 if (nbits & SPI_NBITS_QUAD) 285 bd_ctrl |= BD_QUAD; 286 else if (nbits & SPI_NBITS_DUAL) 287 bd_ctrl |= BD_DUAL; 288 289 /* LSB first */ 290 if (spi->mode & SPI_LSB_FIRST) 291 bd_ctrl |= BD_LSBF; 292 293 /* ownership to hardware */ 294 bd_ctrl |= BD_EN; 295 296 for_each_sg(sgl, sg, nents, i) { 297 /* get ring descriptor */ 298 rdesc = ring_desc_get(sqi); 299 if (!rdesc) 300 break; 301 302 bd = rdesc->bd; 303 304 /* BD CTRL: length */ 305 rdesc->xfer_len = sg_dma_len(sg); 306 bd->bd_ctrl = bd_ctrl; 307 bd->bd_ctrl |= rdesc->xfer_len; 308 309 /* BD STAT */ 310 bd->bd_status = 0; 311 312 /* BD BUFFER ADDRESS */ 313 bd->bd_addr = sg->dma_address; 314 } 315 316 return 0; 317 } 318 319 static int pic32_sqi_prepare_hardware(struct spi_controller *host) 320 { 321 struct pic32_sqi *sqi = spi_controller_get_devdata(host); 322 323 /* enable spi interface */ 324 pic32_setbits(sqi->regs + PESQI_CONF_REG, PESQI_EN); 325 /* enable spi clk */ 326 pic32_setbits(sqi->regs + PESQI_CLK_CTRL_REG, PESQI_CLK_EN); 327 328 return 0; 329 } 330 331 static bool pic32_sqi_can_dma(struct spi_controller *host, 332 struct spi_device *spi, 333 struct spi_transfer *x) 334 { 335 /* Do DMA irrespective of transfer size */ 336 return true; 337 } 338 339 static int pic32_sqi_one_message(struct spi_controller *host, 340 struct spi_message *msg) 341 { 342 struct spi_device *spi = msg->spi; 343 struct ring_desc *rdesc, *next; 344 struct spi_transfer *xfer; 345 struct pic32_sqi *sqi; 346 int ret = 0, mode; 347 unsigned long timeout; 348 u32 val; 349 350 sqi = spi_controller_get_devdata(host); 351 352 reinit_completion(&sqi->xfer_done); 353 msg->actual_length = 0; 354 355 /* We can't handle spi_transfer specific "speed_hz", "bits_per_word" 356 * and "delay_usecs". But spi_device specific speed and mode change 357 * can be handled at best during spi chip-select switch. 358 */ 359 if (sqi->cur_spi != spi) { 360 /* set spi speed */ 361 if (sqi->cur_speed != spi->max_speed_hz) { 362 sqi->cur_speed = spi->max_speed_hz; 363 ret = pic32_sqi_set_clk_rate(sqi, spi->max_speed_hz); 364 if (ret) 365 dev_warn(&spi->dev, "set_clk, %d\n", ret); 366 } 367 368 /* set spi mode */ 369 mode = spi->mode & (SPI_MODE_3 | SPI_LSB_FIRST); 370 if (sqi->cur_mode != mode) { 371 val = readl(sqi->regs + PESQI_CONF_REG); 372 val &= ~(PESQI_CPOL | PESQI_CPHA | PESQI_LSBF); 373 if (mode & SPI_CPOL) 374 val |= PESQI_CPOL; 375 if (mode & SPI_LSB_FIRST) 376 val |= PESQI_LSBF; 377 val |= PESQI_CPHA; 378 writel(val, sqi->regs + PESQI_CONF_REG); 379 380 sqi->cur_mode = mode; 381 } 382 sqi->cur_spi = spi; 383 } 384 385 /* prepare hardware desc-list(BD) for transfer(s) */ 386 list_for_each_entry(xfer, &msg->transfers, transfer_list) { 387 ret = pic32_sqi_one_transfer(sqi, msg, xfer); 388 if (ret) { 389 dev_err(&spi->dev, "xfer %p err\n", xfer); 390 goto xfer_out; 391 } 392 } 393 394 /* BDs are prepared and chained. Now mark LAST_BD, CS_DEASSERT at last 395 * element of the list. 396 */ 397 rdesc = list_last_entry(&sqi->bd_list_used, struct ring_desc, list); 398 rdesc->bd->bd_ctrl |= BD_LAST | BD_CS_DEASSERT | 399 BD_LIFM | BD_PKT_INT_EN; 400 401 /* set base address BD list for DMA engine */ 402 rdesc = list_first_entry(&sqi->bd_list_used, struct ring_desc, list); 403 writel(rdesc->bd_dma, sqi->regs + PESQI_BD_BASE_ADDR_REG); 404 405 /* enable interrupt */ 406 pic32_sqi_enable_int(sqi); 407 408 /* enable DMA engine */ 409 val = PESQI_DMA_EN | PESQI_POLL_EN | PESQI_BDP_START; 410 writel(val, sqi->regs + PESQI_BD_CTRL_REG); 411 412 /* wait for xfer completion */ 413 timeout = wait_for_completion_timeout(&sqi->xfer_done, 5 * HZ); 414 if (timeout == 0) { 415 dev_err(&sqi->host->dev, "wait timedout/interrupted\n"); 416 ret = -ETIMEDOUT; 417 msg->status = ret; 418 } else { 419 /* success */ 420 msg->status = 0; 421 ret = 0; 422 } 423 424 /* disable DMA */ 425 writel(0, sqi->regs + PESQI_BD_CTRL_REG); 426 427 pic32_sqi_disable_int(sqi); 428 429 xfer_out: 430 list_for_each_entry_safe_reverse(rdesc, next, 431 &sqi->bd_list_used, list) { 432 /* Update total byte transferred */ 433 msg->actual_length += rdesc->xfer_len; 434 /* release ring descr */ 435 ring_desc_put(sqi, rdesc); 436 } 437 spi_finalize_current_message(spi->controller); 438 439 return ret; 440 } 441 442 static int pic32_sqi_unprepare_hardware(struct spi_controller *host) 443 { 444 struct pic32_sqi *sqi = spi_controller_get_devdata(host); 445 446 /* disable clk */ 447 pic32_clrbits(sqi->regs + PESQI_CLK_CTRL_REG, PESQI_CLK_EN); 448 /* disable spi */ 449 pic32_clrbits(sqi->regs + PESQI_CONF_REG, PESQI_EN); 450 451 return 0; 452 } 453 454 static int ring_desc_ring_alloc(struct pic32_sqi *sqi) 455 { 456 struct ring_desc *rdesc; 457 struct buf_desc *bd; 458 int i; 459 460 /* allocate coherent DMAable memory for hardware buffer descriptors. */ 461 sqi->bd = dma_alloc_coherent(&sqi->host->dev, 462 sizeof(*bd) * PESQI_BD_COUNT, 463 &sqi->bd_dma, GFP_KERNEL); 464 if (!sqi->bd) { 465 dev_err(&sqi->host->dev, "failed allocating dma buffer\n"); 466 return -ENOMEM; 467 } 468 469 /* allocate software ring descriptors */ 470 sqi->ring = kcalloc(PESQI_BD_COUNT, sizeof(*rdesc), GFP_KERNEL); 471 if (!sqi->ring) { 472 dma_free_coherent(&sqi->host->dev, 473 sizeof(*bd) * PESQI_BD_COUNT, 474 sqi->bd, sqi->bd_dma); 475 return -ENOMEM; 476 } 477 478 bd = (struct buf_desc *)sqi->bd; 479 480 INIT_LIST_HEAD(&sqi->bd_list_free); 481 INIT_LIST_HEAD(&sqi->bd_list_used); 482 483 /* initialize ring-desc */ 484 for (i = 0, rdesc = sqi->ring; i < PESQI_BD_COUNT; i++, rdesc++) { 485 INIT_LIST_HEAD(&rdesc->list); 486 rdesc->bd = &bd[i]; 487 rdesc->bd_dma = sqi->bd_dma + (void *)&bd[i] - (void *)bd; 488 list_add_tail(&rdesc->list, &sqi->bd_list_free); 489 } 490 491 /* Prepare BD: chain to next BD(s) */ 492 for (i = 0, rdesc = sqi->ring; i < PESQI_BD_COUNT - 1; i++) 493 bd[i].bd_nextp = rdesc[i + 1].bd_dma; 494 bd[PESQI_BD_COUNT - 1].bd_nextp = 0; 495 496 return 0; 497 } 498 499 static void ring_desc_ring_free(struct pic32_sqi *sqi) 500 { 501 dma_free_coherent(&sqi->host->dev, 502 sizeof(struct buf_desc) * PESQI_BD_COUNT, 503 sqi->bd, sqi->bd_dma); 504 kfree(sqi->ring); 505 } 506 507 static void pic32_sqi_hw_init(struct pic32_sqi *sqi) 508 { 509 unsigned long flags; 510 u32 val; 511 512 /* Soft-reset of PESQI controller triggers interrupt. 513 * We are not yet ready to handle them so disable CPU 514 * interrupt for the time being. 515 */ 516 local_irq_save(flags); 517 518 /* assert soft-reset */ 519 writel(PESQI_SOFT_RESET, sqi->regs + PESQI_CONF_REG); 520 521 /* wait until clear */ 522 readl_poll_timeout_atomic(sqi->regs + PESQI_CONF_REG, val, 523 !(val & PESQI_SOFT_RESET), 1, 5000); 524 525 /* disable all interrupts */ 526 pic32_sqi_disable_int(sqi); 527 528 /* Now it is safe to enable back CPU interrupt */ 529 local_irq_restore(flags); 530 531 /* tx and rx fifo interrupt threshold */ 532 val = readl(sqi->regs + PESQI_CMD_THRES_REG); 533 val &= ~(PESQI_TXTHR_MASK << PESQI_TXTHR_SHIFT); 534 val &= ~(PESQI_RXTHR_MASK << PESQI_RXTHR_SHIFT); 535 val |= (1U << PESQI_TXTHR_SHIFT) | (1U << PESQI_RXTHR_SHIFT); 536 writel(val, sqi->regs + PESQI_CMD_THRES_REG); 537 538 val = readl(sqi->regs + PESQI_INT_THRES_REG); 539 val &= ~(PESQI_TXTHR_MASK << PESQI_TXTHR_SHIFT); 540 val &= ~(PESQI_RXTHR_MASK << PESQI_RXTHR_SHIFT); 541 val |= (1U << PESQI_TXTHR_SHIFT) | (1U << PESQI_RXTHR_SHIFT); 542 writel(val, sqi->regs + PESQI_INT_THRES_REG); 543 544 /* default configuration */ 545 val = readl(sqi->regs + PESQI_CONF_REG); 546 547 /* set mode: DMA */ 548 val &= ~PESQI_MODE; 549 val |= PESQI_MODE_DMA << PESQI_MODE_SHIFT; 550 writel(val, sqi->regs + PESQI_CONF_REG); 551 552 /* DATAEN - SQIID0-ID3 */ 553 val |= PESQI_QUAD_LANE << PESQI_LANES_SHIFT; 554 555 /* burst/INCR4 enable */ 556 val |= PESQI_BURST_EN; 557 558 /* CSEN - all CS */ 559 val |= 3U << PESQI_CSEN_SHIFT; 560 writel(val, sqi->regs + PESQI_CONF_REG); 561 562 /* write poll count */ 563 writel(0, sqi->regs + PESQI_BD_POLL_CTRL_REG); 564 565 sqi->cur_speed = 0; 566 sqi->cur_mode = -1; 567 } 568 569 static int pic32_sqi_probe(struct platform_device *pdev) 570 { 571 struct spi_controller *host; 572 struct pic32_sqi *sqi; 573 int ret; 574 575 host = spi_alloc_host(&pdev->dev, sizeof(*sqi)); 576 if (!host) 577 return -ENOMEM; 578 579 sqi = spi_controller_get_devdata(host); 580 sqi->host = host; 581 582 sqi->regs = devm_platform_ioremap_resource(pdev, 0); 583 if (IS_ERR(sqi->regs)) { 584 ret = PTR_ERR(sqi->regs); 585 goto err_free_host; 586 } 587 588 /* irq */ 589 sqi->irq = platform_get_irq(pdev, 0); 590 if (sqi->irq < 0) { 591 ret = sqi->irq; 592 goto err_free_host; 593 } 594 595 /* clocks */ 596 sqi->sys_clk = devm_clk_get_enabled(&pdev->dev, "reg_ck"); 597 if (IS_ERR(sqi->sys_clk)) { 598 ret = PTR_ERR(sqi->sys_clk); 599 dev_err(&pdev->dev, "no sys_clk ?\n"); 600 goto err_free_host; 601 } 602 603 sqi->base_clk = devm_clk_get_enabled(&pdev->dev, "spi_ck"); 604 if (IS_ERR(sqi->base_clk)) { 605 ret = PTR_ERR(sqi->base_clk); 606 dev_err(&pdev->dev, "no base clk ?\n"); 607 goto err_free_host; 608 } 609 610 init_completion(&sqi->xfer_done); 611 612 /* initialize hardware */ 613 pic32_sqi_hw_init(sqi); 614 615 /* allocate buffers & descriptors */ 616 ret = ring_desc_ring_alloc(sqi); 617 if (ret) { 618 dev_err(&pdev->dev, "ring alloc failed\n"); 619 goto err_free_host; 620 } 621 622 /* install irq handlers */ 623 ret = request_irq(sqi->irq, pic32_sqi_isr, 0, 624 dev_name(&pdev->dev), sqi); 625 if (ret < 0) { 626 dev_err(&pdev->dev, "request_irq(%d), failed\n", sqi->irq); 627 goto err_free_ring; 628 } 629 630 /* register host */ 631 host->num_chipselect = 2; 632 host->max_speed_hz = clk_get_rate(sqi->base_clk); 633 host->dma_alignment = 32; 634 host->max_dma_len = PESQI_BD_BUF_LEN_MAX; 635 host->dev.of_node = pdev->dev.of_node; 636 host->mode_bits = SPI_MODE_3 | SPI_MODE_0 | SPI_TX_DUAL | 637 SPI_RX_DUAL | SPI_TX_QUAD | SPI_RX_QUAD; 638 host->flags = SPI_CONTROLLER_HALF_DUPLEX; 639 host->can_dma = pic32_sqi_can_dma; 640 host->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 32); 641 host->transfer_one_message = pic32_sqi_one_message; 642 host->prepare_transfer_hardware = pic32_sqi_prepare_hardware; 643 host->unprepare_transfer_hardware = pic32_sqi_unprepare_hardware; 644 645 ret = devm_spi_register_controller(&pdev->dev, host); 646 if (ret) { 647 dev_err(&host->dev, "failed registering spi host\n"); 648 free_irq(sqi->irq, sqi); 649 goto err_free_ring; 650 } 651 652 platform_set_drvdata(pdev, sqi); 653 654 return 0; 655 656 err_free_ring: 657 ring_desc_ring_free(sqi); 658 659 err_free_host: 660 spi_controller_put(host); 661 return ret; 662 } 663 664 static void pic32_sqi_remove(struct platform_device *pdev) 665 { 666 struct pic32_sqi *sqi = platform_get_drvdata(pdev); 667 668 /* release resources */ 669 free_irq(sqi->irq, sqi); 670 ring_desc_ring_free(sqi); 671 } 672 673 static const struct of_device_id pic32_sqi_of_ids[] = { 674 {.compatible = "microchip,pic32mzda-sqi",}, 675 {}, 676 }; 677 MODULE_DEVICE_TABLE(of, pic32_sqi_of_ids); 678 679 static struct platform_driver pic32_sqi_driver = { 680 .driver = { 681 .name = "sqi-pic32", 682 .of_match_table = of_match_ptr(pic32_sqi_of_ids), 683 }, 684 .probe = pic32_sqi_probe, 685 .remove_new = pic32_sqi_remove, 686 }; 687 688 module_platform_driver(pic32_sqi_driver); 689 690 MODULE_AUTHOR("Purna Chandra Mandal <purna.mandal@microchip.com>"); 691 MODULE_DESCRIPTION("Microchip SPI driver for PIC32 SQI controller."); 692 MODULE_LICENSE("GPL v2"); 693