1 /* 2 * Driver for Amlogic Meson SPI communication controller (SPICC) 3 * 4 * Copyright (C) BayLibre, SAS 5 * Author: Neil Armstrong <narmstrong@baylibre.com> 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #include <linux/bitfield.h> 11 #include <linux/clk.h> 12 #include <linux/clk-provider.h> 13 #include <linux/device.h> 14 #include <linux/io.h> 15 #include <linux/kernel.h> 16 #include <linux/module.h> 17 #include <linux/of.h> 18 #include <linux/platform_device.h> 19 #include <linux/spi/spi.h> 20 #include <linux/types.h> 21 #include <linux/interrupt.h> 22 #include <linux/reset.h> 23 #include <linux/pinctrl/consumer.h> 24 25 /* 26 * The Meson SPICC controller could support DMA based transfers, but is not 27 * implemented by the vendor code, and while having the registers documentation 28 * it has never worked on the GXL Hardware. 29 * The PIO mode is the only mode implemented, and due to badly designed HW : 30 * - all transfers are cutted in 16 words burst because the FIFO hangs on 31 * TX underflow, and there is no TX "Half-Empty" interrupt, so we go by 32 * FIFO max size chunk only 33 * - CS management is dumb, and goes UP between every burst, so is really a 34 * "Data Valid" signal than a Chip Select, GPIO link should be used instead 35 * to have a CS go down over the full transfer 36 */ 37 38 #define SPICC_MAX_BURST 128 39 40 /* Register Map */ 41 #define SPICC_RXDATA 0x00 42 43 #define SPICC_TXDATA 0x04 44 45 #define SPICC_CONREG 0x08 46 #define SPICC_ENABLE BIT(0) 47 #define SPICC_MODE_MASTER BIT(1) 48 #define SPICC_XCH BIT(2) 49 #define SPICC_SMC BIT(3) 50 #define SPICC_POL BIT(4) 51 #define SPICC_PHA BIT(5) 52 #define SPICC_SSCTL BIT(6) 53 #define SPICC_SSPOL BIT(7) 54 #define SPICC_DRCTL_MASK GENMASK(9, 8) 55 #define SPICC_DRCTL_IGNORE 0 56 #define SPICC_DRCTL_FALLING 1 57 #define SPICC_DRCTL_LOWLEVEL 2 58 #define SPICC_CS_MASK GENMASK(13, 12) 59 #define SPICC_DATARATE_MASK GENMASK(18, 16) 60 #define SPICC_DATARATE_DIV4 0 61 #define SPICC_DATARATE_DIV8 1 62 #define SPICC_DATARATE_DIV16 2 63 #define SPICC_DATARATE_DIV32 3 64 #define SPICC_BITLENGTH_MASK GENMASK(24, 19) 65 #define SPICC_BURSTLENGTH_MASK GENMASK(31, 25) 66 67 #define SPICC_INTREG 0x0c 68 #define SPICC_TE_EN BIT(0) /* TX FIFO Empty Interrupt */ 69 #define SPICC_TH_EN BIT(1) /* TX FIFO Half-Full Interrupt */ 70 #define SPICC_TF_EN BIT(2) /* TX FIFO Full Interrupt */ 71 #define SPICC_RR_EN BIT(3) /* RX FIFO Ready Interrupt */ 72 #define SPICC_RH_EN BIT(4) /* RX FIFO Half-Full Interrupt */ 73 #define SPICC_RF_EN BIT(5) /* RX FIFO Full Interrupt */ 74 #define SPICC_RO_EN BIT(6) /* RX FIFO Overflow Interrupt */ 75 #define SPICC_TC_EN BIT(7) /* Transfert Complete Interrupt */ 76 77 #define SPICC_DMAREG 0x10 78 #define SPICC_DMA_ENABLE BIT(0) 79 #define SPICC_TXFIFO_THRESHOLD_MASK GENMASK(5, 1) 80 #define SPICC_RXFIFO_THRESHOLD_MASK GENMASK(10, 6) 81 #define SPICC_READ_BURST_MASK GENMASK(14, 11) 82 #define SPICC_WRITE_BURST_MASK GENMASK(18, 15) 83 #define SPICC_DMA_URGENT BIT(19) 84 #define SPICC_DMA_THREADID_MASK GENMASK(25, 20) 85 #define SPICC_DMA_BURSTNUM_MASK GENMASK(31, 26) 86 87 #define SPICC_STATREG 0x14 88 #define SPICC_TE BIT(0) /* TX FIFO Empty Interrupt */ 89 #define SPICC_TH BIT(1) /* TX FIFO Half-Full Interrupt */ 90 #define SPICC_TF BIT(2) /* TX FIFO Full Interrupt */ 91 #define SPICC_RR BIT(3) /* RX FIFO Ready Interrupt */ 92 #define SPICC_RH BIT(4) /* RX FIFO Half-Full Interrupt */ 93 #define SPICC_RF BIT(5) /* RX FIFO Full Interrupt */ 94 #define SPICC_RO BIT(6) /* RX FIFO Overflow Interrupt */ 95 #define SPICC_TC BIT(7) /* Transfert Complete Interrupt */ 96 97 #define SPICC_PERIODREG 0x18 98 #define SPICC_PERIOD GENMASK(14, 0) /* Wait cycles */ 99 100 #define SPICC_TESTREG 0x1c 101 #define SPICC_TXCNT_MASK GENMASK(4, 0) /* TX FIFO Counter */ 102 #define SPICC_RXCNT_MASK GENMASK(9, 5) /* RX FIFO Counter */ 103 #define SPICC_SMSTATUS_MASK GENMASK(12, 10) /* State Machine Status */ 104 #define SPICC_LBC_RO BIT(13) /* Loop Back Control Read-Only */ 105 #define SPICC_LBC_W1 BIT(14) /* Loop Back Control Write-Only */ 106 #define SPICC_SWAP_RO BIT(14) /* RX FIFO Data Swap Read-Only */ 107 #define SPICC_SWAP_W1 BIT(15) /* RX FIFO Data Swap Write-Only */ 108 #define SPICC_DLYCTL_RO_MASK GENMASK(20, 15) /* Delay Control Read-Only */ 109 #define SPICC_MO_DELAY_MASK GENMASK(17, 16) /* Master Output Delay */ 110 #define SPICC_MO_NO_DELAY 0 111 #define SPICC_MO_DELAY_1_CYCLE 1 112 #define SPICC_MO_DELAY_2_CYCLE 2 113 #define SPICC_MO_DELAY_3_CYCLE 3 114 #define SPICC_MI_DELAY_MASK GENMASK(19, 18) /* Master Input Delay */ 115 #define SPICC_MI_NO_DELAY 0 116 #define SPICC_MI_DELAY_1_CYCLE 1 117 #define SPICC_MI_DELAY_2_CYCLE 2 118 #define SPICC_MI_DELAY_3_CYCLE 3 119 #define SPICC_MI_CAP_DELAY_MASK GENMASK(21, 20) /* Master Capture Delay */ 120 #define SPICC_CAP_AHEAD_2_CYCLE 0 121 #define SPICC_CAP_AHEAD_1_CYCLE 1 122 #define SPICC_CAP_NO_DELAY 2 123 #define SPICC_CAP_DELAY_1_CYCLE 3 124 #define SPICC_FIFORST_RO_MASK GENMASK(22, 21) /* FIFO Softreset Read-Only */ 125 #define SPICC_FIFORST_W1_MASK GENMASK(23, 22) /* FIFO Softreset Write-Only */ 126 127 #define SPICC_DRADDR 0x20 /* Read Address of DMA */ 128 129 #define SPICC_DWADDR 0x24 /* Write Address of DMA */ 130 131 #define SPICC_ENH_CTL0 0x38 /* Enhanced Feature */ 132 #define SPICC_ENH_CLK_CS_DELAY_MASK GENMASK(15, 0) 133 #define SPICC_ENH_DATARATE_MASK GENMASK(23, 16) 134 #define SPICC_ENH_DATARATE_EN BIT(24) 135 #define SPICC_ENH_MOSI_OEN BIT(25) 136 #define SPICC_ENH_CLK_OEN BIT(26) 137 #define SPICC_ENH_CS_OEN BIT(27) 138 #define SPICC_ENH_CLK_CS_DELAY_EN BIT(28) 139 #define SPICC_ENH_MAIN_CLK_AO BIT(29) 140 141 #define writel_bits_relaxed(mask, val, addr) \ 142 writel_relaxed((readl_relaxed(addr) & ~(mask)) | (val), addr) 143 144 struct meson_spicc_data { 145 unsigned int max_speed_hz; 146 unsigned int min_speed_hz; 147 unsigned int fifo_size; 148 bool has_oen; 149 bool has_enhance_clk_div; 150 bool has_pclk; 151 }; 152 153 struct meson_spicc_device { 154 struct spi_controller *host; 155 struct platform_device *pdev; 156 void __iomem *base; 157 struct clk *core; 158 struct clk *pclk; 159 struct clk_divider pow2_div; 160 struct clk *clk; 161 struct spi_message *message; 162 struct spi_transfer *xfer; 163 struct completion done; 164 const struct meson_spicc_data *data; 165 u8 *tx_buf; 166 u8 *rx_buf; 167 unsigned int bytes_per_word; 168 unsigned long tx_remain; 169 unsigned long rx_remain; 170 unsigned long xfer_remain; 171 struct pinctrl *pinctrl; 172 struct pinctrl_state *pins_idle_high; 173 struct pinctrl_state *pins_idle_low; 174 }; 175 176 #define pow2_clk_to_spicc(_div) container_of(_div, struct meson_spicc_device, pow2_div) 177 178 static void meson_spicc_oen_enable(struct meson_spicc_device *spicc) 179 { 180 u32 conf; 181 182 if (!spicc->data->has_oen) { 183 /* Try to get pinctrl states for idle high/low */ 184 spicc->pins_idle_high = pinctrl_lookup_state(spicc->pinctrl, 185 "idle-high"); 186 if (IS_ERR(spicc->pins_idle_high)) { 187 dev_warn(&spicc->pdev->dev, "can't get idle-high pinctrl\n"); 188 spicc->pins_idle_high = NULL; 189 } 190 spicc->pins_idle_low = pinctrl_lookup_state(spicc->pinctrl, 191 "idle-low"); 192 if (IS_ERR(spicc->pins_idle_low)) { 193 dev_warn(&spicc->pdev->dev, "can't get idle-low pinctrl\n"); 194 spicc->pins_idle_low = NULL; 195 } 196 return; 197 } 198 199 conf = readl_relaxed(spicc->base + SPICC_ENH_CTL0) | 200 SPICC_ENH_MOSI_OEN | SPICC_ENH_CLK_OEN | SPICC_ENH_CS_OEN; 201 202 writel_relaxed(conf, spicc->base + SPICC_ENH_CTL0); 203 } 204 205 static inline bool meson_spicc_txfull(struct meson_spicc_device *spicc) 206 { 207 return !!FIELD_GET(SPICC_TF, 208 readl_relaxed(spicc->base + SPICC_STATREG)); 209 } 210 211 static inline bool meson_spicc_rxready(struct meson_spicc_device *spicc) 212 { 213 return FIELD_GET(SPICC_RH | SPICC_RR | SPICC_RF, 214 readl_relaxed(spicc->base + SPICC_STATREG)); 215 } 216 217 static inline u32 meson_spicc_pull_data(struct meson_spicc_device *spicc) 218 { 219 unsigned int bytes = spicc->bytes_per_word; 220 unsigned int byte_shift = 0; 221 u32 data = 0; 222 u8 byte; 223 224 while (bytes--) { 225 byte = *spicc->tx_buf++; 226 data |= (byte & 0xff) << byte_shift; 227 byte_shift += 8; 228 } 229 230 spicc->tx_remain--; 231 return data; 232 } 233 234 static inline void meson_spicc_push_data(struct meson_spicc_device *spicc, 235 u32 data) 236 { 237 unsigned int bytes = spicc->bytes_per_word; 238 unsigned int byte_shift = 0; 239 u8 byte; 240 241 while (bytes--) { 242 byte = (data >> byte_shift) & 0xff; 243 *spicc->rx_buf++ = byte; 244 byte_shift += 8; 245 } 246 247 spicc->rx_remain--; 248 } 249 250 static inline void meson_spicc_rx(struct meson_spicc_device *spicc) 251 { 252 /* Empty RX FIFO */ 253 while (spicc->rx_remain && 254 meson_spicc_rxready(spicc)) 255 meson_spicc_push_data(spicc, 256 readl_relaxed(spicc->base + SPICC_RXDATA)); 257 } 258 259 static inline void meson_spicc_tx(struct meson_spicc_device *spicc) 260 { 261 /* Fill Up TX FIFO */ 262 while (spicc->tx_remain && 263 !meson_spicc_txfull(spicc)) 264 writel_relaxed(meson_spicc_pull_data(spicc), 265 spicc->base + SPICC_TXDATA); 266 } 267 268 static inline void meson_spicc_setup_burst(struct meson_spicc_device *spicc) 269 { 270 271 unsigned int burst_len = min_t(unsigned int, 272 spicc->xfer_remain / 273 spicc->bytes_per_word, 274 spicc->data->fifo_size); 275 /* Setup Xfer variables */ 276 spicc->tx_remain = burst_len; 277 spicc->rx_remain = burst_len; 278 spicc->xfer_remain -= burst_len * spicc->bytes_per_word; 279 280 /* Setup burst length */ 281 writel_bits_relaxed(SPICC_BURSTLENGTH_MASK, 282 FIELD_PREP(SPICC_BURSTLENGTH_MASK, 283 burst_len - 1), 284 spicc->base + SPICC_CONREG); 285 286 /* Fill TX FIFO */ 287 meson_spicc_tx(spicc); 288 } 289 290 static irqreturn_t meson_spicc_irq(int irq, void *data) 291 { 292 struct meson_spicc_device *spicc = (void *) data; 293 294 writel_bits_relaxed(SPICC_TC, SPICC_TC, spicc->base + SPICC_STATREG); 295 296 /* Empty RX FIFO */ 297 meson_spicc_rx(spicc); 298 299 if (!spicc->xfer_remain) { 300 /* Disable all IRQs */ 301 writel(0, spicc->base + SPICC_INTREG); 302 303 complete(&spicc->done); 304 305 return IRQ_HANDLED; 306 } 307 308 /* Setup burst */ 309 meson_spicc_setup_burst(spicc); 310 311 /* Start burst */ 312 writel_bits_relaxed(SPICC_XCH, SPICC_XCH, spicc->base + SPICC_CONREG); 313 314 return IRQ_HANDLED; 315 } 316 317 static void meson_spicc_auto_io_delay(struct meson_spicc_device *spicc) 318 { 319 u32 div, hz; 320 u32 mi_delay, cap_delay; 321 u32 conf; 322 323 if (spicc->data->has_enhance_clk_div) { 324 div = FIELD_GET(SPICC_ENH_DATARATE_MASK, 325 readl_relaxed(spicc->base + SPICC_ENH_CTL0)); 326 div++; 327 div <<= 1; 328 } else { 329 div = FIELD_GET(SPICC_DATARATE_MASK, 330 readl_relaxed(spicc->base + SPICC_CONREG)); 331 div += 2; 332 div = 1 << div; 333 } 334 335 mi_delay = SPICC_MI_NO_DELAY; 336 cap_delay = SPICC_CAP_AHEAD_2_CYCLE; 337 hz = clk_get_rate(spicc->clk); 338 339 if (hz >= 100000000) 340 cap_delay = SPICC_CAP_DELAY_1_CYCLE; 341 else if (hz >= 80000000) 342 cap_delay = SPICC_CAP_NO_DELAY; 343 else if (hz >= 40000000) 344 cap_delay = SPICC_CAP_AHEAD_1_CYCLE; 345 else if (div >= 16) 346 mi_delay = SPICC_MI_DELAY_3_CYCLE; 347 else if (div >= 8) 348 mi_delay = SPICC_MI_DELAY_2_CYCLE; 349 else if (div >= 6) 350 mi_delay = SPICC_MI_DELAY_1_CYCLE; 351 352 conf = readl_relaxed(spicc->base + SPICC_TESTREG); 353 conf &= ~(SPICC_MO_DELAY_MASK | SPICC_MI_DELAY_MASK 354 | SPICC_MI_CAP_DELAY_MASK); 355 conf |= FIELD_PREP(SPICC_MI_DELAY_MASK, mi_delay); 356 conf |= FIELD_PREP(SPICC_MI_CAP_DELAY_MASK, cap_delay); 357 writel_relaxed(conf, spicc->base + SPICC_TESTREG); 358 } 359 360 static void meson_spicc_setup_xfer(struct meson_spicc_device *spicc, 361 struct spi_transfer *xfer) 362 { 363 u32 conf, conf_orig; 364 365 /* Read original configuration */ 366 conf = conf_orig = readl_relaxed(spicc->base + SPICC_CONREG); 367 368 /* Setup word width */ 369 conf &= ~SPICC_BITLENGTH_MASK; 370 conf |= FIELD_PREP(SPICC_BITLENGTH_MASK, 371 (spicc->bytes_per_word << 3) - 1); 372 373 /* Ignore if unchanged */ 374 if (conf != conf_orig) 375 writel_relaxed(conf, spicc->base + SPICC_CONREG); 376 377 clk_set_rate(spicc->clk, xfer->speed_hz); 378 379 meson_spicc_auto_io_delay(spicc); 380 381 writel_relaxed(0, spicc->base + SPICC_DMAREG); 382 } 383 384 static void meson_spicc_reset_fifo(struct meson_spicc_device *spicc) 385 { 386 if (spicc->data->has_oen) 387 writel_bits_relaxed(SPICC_ENH_MAIN_CLK_AO, 388 SPICC_ENH_MAIN_CLK_AO, 389 spicc->base + SPICC_ENH_CTL0); 390 391 writel_bits_relaxed(SPICC_FIFORST_W1_MASK, SPICC_FIFORST_W1_MASK, 392 spicc->base + SPICC_TESTREG); 393 394 while (meson_spicc_rxready(spicc)) 395 readl_relaxed(spicc->base + SPICC_RXDATA); 396 397 if (spicc->data->has_oen) 398 writel_bits_relaxed(SPICC_ENH_MAIN_CLK_AO, 0, 399 spicc->base + SPICC_ENH_CTL0); 400 } 401 402 static int meson_spicc_transfer_one(struct spi_controller *host, 403 struct spi_device *spi, 404 struct spi_transfer *xfer) 405 { 406 struct meson_spicc_device *spicc = spi_controller_get_devdata(host); 407 uint64_t timeout; 408 409 /* Store current transfer */ 410 spicc->xfer = xfer; 411 412 /* Setup transfer parameters */ 413 spicc->tx_buf = (u8 *)xfer->tx_buf; 414 spicc->rx_buf = (u8 *)xfer->rx_buf; 415 spicc->xfer_remain = xfer->len; 416 417 /* Pre-calculate word size */ 418 spicc->bytes_per_word = 419 DIV_ROUND_UP(spicc->xfer->bits_per_word, 8); 420 421 if (xfer->len % spicc->bytes_per_word) 422 return -EINVAL; 423 424 /* Setup transfer parameters */ 425 meson_spicc_setup_xfer(spicc, xfer); 426 427 meson_spicc_reset_fifo(spicc); 428 429 /* Setup burst */ 430 meson_spicc_setup_burst(spicc); 431 432 /* Setup wait for completion */ 433 reinit_completion(&spicc->done); 434 435 /* For each byte we wait for 8 cycles of the SPI clock */ 436 timeout = 8LL * MSEC_PER_SEC * xfer->len; 437 do_div(timeout, xfer->speed_hz); 438 439 /* Add 10us delay between each fifo bursts */ 440 timeout += ((xfer->len >> 4) * 10) / MSEC_PER_SEC; 441 442 /* Increase it twice and add 200 ms tolerance */ 443 timeout += timeout + 200; 444 445 /* Start burst */ 446 writel_bits_relaxed(SPICC_XCH, SPICC_XCH, spicc->base + SPICC_CONREG); 447 448 /* Enable interrupts */ 449 writel_relaxed(SPICC_TC_EN, spicc->base + SPICC_INTREG); 450 451 if (!wait_for_completion_timeout(&spicc->done, msecs_to_jiffies(timeout))) 452 return -ETIMEDOUT; 453 454 return 0; 455 } 456 457 static int meson_spicc_prepare_message(struct spi_controller *host, 458 struct spi_message *message) 459 { 460 struct meson_spicc_device *spicc = spi_controller_get_devdata(host); 461 struct spi_device *spi = message->spi; 462 u32 conf = readl_relaxed(spicc->base + SPICC_CONREG) & SPICC_DATARATE_MASK; 463 464 /* Store current message */ 465 spicc->message = message; 466 467 /* Enable Master */ 468 conf |= SPICC_ENABLE; 469 conf |= SPICC_MODE_MASTER; 470 471 /* SMC = 0 */ 472 473 /* Setup transfer mode */ 474 if (spi->mode & SPI_CPOL) 475 conf |= SPICC_POL; 476 else 477 conf &= ~SPICC_POL; 478 479 if (!spicc->data->has_oen) { 480 if (spi->mode & SPI_CPOL) { 481 if (spicc->pins_idle_high) 482 pinctrl_select_state(spicc->pinctrl, spicc->pins_idle_high); 483 } else { 484 if (spicc->pins_idle_low) 485 pinctrl_select_state(spicc->pinctrl, spicc->pins_idle_low); 486 } 487 } 488 489 if (spi->mode & SPI_CPHA) 490 conf |= SPICC_PHA; 491 else 492 conf &= ~SPICC_PHA; 493 494 /* SSCTL = 0 */ 495 496 if (spi->mode & SPI_CS_HIGH) 497 conf |= SPICC_SSPOL; 498 else 499 conf &= ~SPICC_SSPOL; 500 501 if (spi->mode & SPI_READY) 502 conf |= FIELD_PREP(SPICC_DRCTL_MASK, SPICC_DRCTL_LOWLEVEL); 503 else 504 conf |= FIELD_PREP(SPICC_DRCTL_MASK, SPICC_DRCTL_IGNORE); 505 506 /* Select CS */ 507 conf |= FIELD_PREP(SPICC_CS_MASK, spi_get_chipselect(spi, 0)); 508 509 /* Default 8bit word */ 510 conf |= FIELD_PREP(SPICC_BITLENGTH_MASK, 8 - 1); 511 512 writel_relaxed(conf, spicc->base + SPICC_CONREG); 513 514 /* Setup no wait cycles by default */ 515 writel_relaxed(0, spicc->base + SPICC_PERIODREG); 516 517 writel_bits_relaxed(SPICC_LBC_W1, 518 spi->mode & SPI_LOOP ? SPICC_LBC_W1 : 0, 519 spicc->base + SPICC_TESTREG); 520 521 return 0; 522 } 523 524 static int meson_spicc_unprepare_transfer(struct spi_controller *host) 525 { 526 struct meson_spicc_device *spicc = spi_controller_get_devdata(host); 527 u32 conf = readl_relaxed(spicc->base + SPICC_CONREG) & SPICC_DATARATE_MASK; 528 529 /* Disable all IRQs */ 530 writel(0, spicc->base + SPICC_INTREG); 531 532 device_reset_optional(&spicc->pdev->dev); 533 534 /* Set default configuration, keeping datarate field */ 535 writel_relaxed(conf, spicc->base + SPICC_CONREG); 536 537 if (!spicc->data->has_oen) 538 pinctrl_select_default_state(&spicc->pdev->dev); 539 540 return 0; 541 } 542 543 static int meson_spicc_setup(struct spi_device *spi) 544 { 545 if (!spi->controller_state) 546 spi->controller_state = spi_controller_get_devdata(spi->controller); 547 548 return 0; 549 } 550 551 static void meson_spicc_cleanup(struct spi_device *spi) 552 { 553 spi->controller_state = NULL; 554 } 555 556 /* 557 * The Clock Mux 558 * x-----------------x x------------x x------\ 559 * |---| pow2 fixed div |---| pow2 div |----| | 560 * | x-----------------x x------------x | | 561 * src ---| | mux |-- out 562 * | x-----------------x x------------x | | 563 * |---| enh fixed div |---| enh div |0---| | 564 * x-----------------x x------------x x------/ 565 * 566 * Clk path for GX series: 567 * src -> pow2 fixed div -> pow2 div -> out 568 * 569 * Clk path for AXG series: 570 * src -> pow2 fixed div -> pow2 div -> mux -> out 571 * src -> enh fixed div -> enh div -> mux -> out 572 * 573 * Clk path for G12A series: 574 * pclk -> pow2 fixed div -> pow2 div -> mux -> out 575 * pclk -> enh fixed div -> enh div -> mux -> out 576 * 577 * The pow2 divider is tied to the controller HW state, and the 578 * divider is only valid when the controller is initialized. 579 * 580 * A set of clock ops is added to make sure we don't read/set this 581 * clock rate while the controller is in an unknown state. 582 */ 583 584 static unsigned long meson_spicc_pow2_recalc_rate(struct clk_hw *hw, 585 unsigned long parent_rate) 586 { 587 struct clk_divider *divider = to_clk_divider(hw); 588 struct meson_spicc_device *spicc = pow2_clk_to_spicc(divider); 589 590 if (!spicc->host->cur_msg) 591 return 0; 592 593 return clk_divider_ops.recalc_rate(hw, parent_rate); 594 } 595 596 static int meson_spicc_pow2_determine_rate(struct clk_hw *hw, 597 struct clk_rate_request *req) 598 { 599 struct clk_divider *divider = to_clk_divider(hw); 600 struct meson_spicc_device *spicc = pow2_clk_to_spicc(divider); 601 602 if (!spicc->host->cur_msg) 603 return -EINVAL; 604 605 return clk_divider_ops.determine_rate(hw, req); 606 } 607 608 static int meson_spicc_pow2_set_rate(struct clk_hw *hw, unsigned long rate, 609 unsigned long parent_rate) 610 { 611 struct clk_divider *divider = to_clk_divider(hw); 612 struct meson_spicc_device *spicc = pow2_clk_to_spicc(divider); 613 614 if (!spicc->host->cur_msg) 615 return -EINVAL; 616 617 return clk_divider_ops.set_rate(hw, rate, parent_rate); 618 } 619 620 static const struct clk_ops meson_spicc_pow2_clk_ops = { 621 .recalc_rate = meson_spicc_pow2_recalc_rate, 622 .determine_rate = meson_spicc_pow2_determine_rate, 623 .set_rate = meson_spicc_pow2_set_rate, 624 }; 625 626 static int meson_spicc_pow2_clk_init(struct meson_spicc_device *spicc) 627 { 628 struct device *dev = &spicc->pdev->dev; 629 struct clk_fixed_factor *pow2_fixed_div; 630 struct clk_init_data init; 631 struct clk *clk; 632 struct clk_parent_data parent_data[2]; 633 char name[64]; 634 635 memset(&init, 0, sizeof(init)); 636 memset(&parent_data, 0, sizeof(parent_data)); 637 638 init.parent_data = parent_data; 639 640 /* algorithm for pow2 div: rate = freq / 4 / (2 ^ N) */ 641 642 pow2_fixed_div = devm_kzalloc(dev, sizeof(*pow2_fixed_div), GFP_KERNEL); 643 if (!pow2_fixed_div) 644 return -ENOMEM; 645 646 snprintf(name, sizeof(name), "%s#pow2_fixed_div", dev_name(dev)); 647 init.name = name; 648 init.ops = &clk_fixed_factor_ops; 649 if (spicc->data->has_pclk) { 650 init.flags = CLK_SET_RATE_PARENT; 651 parent_data[0].hw = __clk_get_hw(spicc->pclk); 652 } else { 653 init.flags = 0; 654 parent_data[0].hw = __clk_get_hw(spicc->core); 655 } 656 init.num_parents = 1; 657 658 pow2_fixed_div->mult = 1; 659 pow2_fixed_div->div = 4; 660 pow2_fixed_div->hw.init = &init; 661 662 clk = devm_clk_register(dev, &pow2_fixed_div->hw); 663 if (WARN_ON(IS_ERR(clk))) 664 return PTR_ERR(clk); 665 666 snprintf(name, sizeof(name), "%s#pow2_div", dev_name(dev)); 667 init.name = name; 668 init.ops = &meson_spicc_pow2_clk_ops; 669 /* 670 * Set NOCACHE here to make sure we read the actual HW value 671 * since we reset the HW after each transfer. 672 */ 673 init.flags = CLK_SET_RATE_PARENT | CLK_GET_RATE_NOCACHE; 674 parent_data[0].hw = &pow2_fixed_div->hw; 675 init.num_parents = 1; 676 677 spicc->pow2_div.shift = 16; 678 spicc->pow2_div.width = 3; 679 spicc->pow2_div.flags = CLK_DIVIDER_POWER_OF_TWO; 680 spicc->pow2_div.reg = spicc->base + SPICC_CONREG; 681 spicc->pow2_div.hw.init = &init; 682 683 spicc->clk = devm_clk_register(dev, &spicc->pow2_div.hw); 684 if (WARN_ON(IS_ERR(spicc->clk))) 685 return PTR_ERR(spicc->clk); 686 687 return 0; 688 } 689 690 static int meson_spicc_enh_clk_init(struct meson_spicc_device *spicc) 691 { 692 struct device *dev = &spicc->pdev->dev; 693 struct clk_fixed_factor *enh_fixed_div; 694 struct clk_divider *enh_div; 695 struct clk_mux *mux; 696 struct clk_init_data init; 697 struct clk *clk; 698 struct clk_parent_data parent_data[2]; 699 char name[64]; 700 701 memset(&init, 0, sizeof(init)); 702 memset(&parent_data, 0, sizeof(parent_data)); 703 704 init.parent_data = parent_data; 705 706 /* algorithm for enh div: rate = freq / 2 / (N + 1) */ 707 708 enh_fixed_div = devm_kzalloc(dev, sizeof(*enh_fixed_div), GFP_KERNEL); 709 if (!enh_fixed_div) 710 return -ENOMEM; 711 712 snprintf(name, sizeof(name), "%s#enh_fixed_div", dev_name(dev)); 713 init.name = name; 714 init.ops = &clk_fixed_factor_ops; 715 if (spicc->data->has_pclk) { 716 init.flags = CLK_SET_RATE_PARENT; 717 parent_data[0].hw = __clk_get_hw(spicc->pclk); 718 } else { 719 init.flags = 0; 720 parent_data[0].hw = __clk_get_hw(spicc->core); 721 } 722 init.num_parents = 1; 723 724 enh_fixed_div->mult = 1; 725 enh_fixed_div->div = 2; 726 enh_fixed_div->hw.init = &init; 727 728 clk = devm_clk_register(dev, &enh_fixed_div->hw); 729 if (WARN_ON(IS_ERR(clk))) 730 return PTR_ERR(clk); 731 732 enh_div = devm_kzalloc(dev, sizeof(*enh_div), GFP_KERNEL); 733 if (!enh_div) 734 return -ENOMEM; 735 736 snprintf(name, sizeof(name), "%s#enh_div", dev_name(dev)); 737 init.name = name; 738 init.ops = &clk_divider_ops; 739 init.flags = CLK_SET_RATE_PARENT; 740 parent_data[0].hw = &enh_fixed_div->hw; 741 init.num_parents = 1; 742 743 enh_div->shift = 16; 744 enh_div->width = 8; 745 enh_div->reg = spicc->base + SPICC_ENH_CTL0; 746 enh_div->hw.init = &init; 747 748 clk = devm_clk_register(dev, &enh_div->hw); 749 if (WARN_ON(IS_ERR(clk))) 750 return PTR_ERR(clk); 751 752 mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL); 753 if (!mux) 754 return -ENOMEM; 755 756 snprintf(name, sizeof(name), "%s#sel", dev_name(dev)); 757 init.name = name; 758 init.ops = &clk_mux_ops; 759 parent_data[0].hw = &spicc->pow2_div.hw; 760 parent_data[1].hw = &enh_div->hw; 761 init.num_parents = 2; 762 init.flags = CLK_SET_RATE_PARENT; 763 764 mux->mask = 0x1; 765 mux->shift = 24; 766 mux->reg = spicc->base + SPICC_ENH_CTL0; 767 mux->hw.init = &init; 768 769 spicc->clk = devm_clk_register(dev, &mux->hw); 770 if (WARN_ON(IS_ERR(spicc->clk))) 771 return PTR_ERR(spicc->clk); 772 773 return 0; 774 } 775 776 static int meson_spicc_probe(struct platform_device *pdev) 777 { 778 struct spi_controller *host; 779 struct meson_spicc_device *spicc; 780 int ret, irq; 781 782 host = spi_alloc_host(&pdev->dev, sizeof(*spicc)); 783 if (!host) { 784 dev_err(&pdev->dev, "host allocation failed\n"); 785 return -ENOMEM; 786 } 787 spicc = spi_controller_get_devdata(host); 788 spicc->host = host; 789 790 spicc->data = of_device_get_match_data(&pdev->dev); 791 if (!spicc->data) { 792 dev_err(&pdev->dev, "failed to get match data\n"); 793 ret = -EINVAL; 794 goto out_host; 795 } 796 797 spicc->pdev = pdev; 798 platform_set_drvdata(pdev, spicc); 799 800 init_completion(&spicc->done); 801 802 spicc->base = devm_platform_ioremap_resource(pdev, 0); 803 if (IS_ERR(spicc->base)) { 804 dev_err(&pdev->dev, "io resource mapping failed\n"); 805 ret = PTR_ERR(spicc->base); 806 goto out_host; 807 } 808 809 /* Set master mode and enable controller */ 810 writel_relaxed(SPICC_ENABLE | SPICC_MODE_MASTER, 811 spicc->base + SPICC_CONREG); 812 813 /* Disable all IRQs */ 814 writel_relaxed(0, spicc->base + SPICC_INTREG); 815 816 irq = platform_get_irq(pdev, 0); 817 if (irq < 0) { 818 ret = irq; 819 goto out_host; 820 } 821 822 ret = devm_request_irq(&pdev->dev, irq, meson_spicc_irq, 823 0, NULL, spicc); 824 if (ret) { 825 dev_err(&pdev->dev, "irq request failed\n"); 826 goto out_host; 827 } 828 829 spicc->core = devm_clk_get_enabled(&pdev->dev, "core"); 830 if (IS_ERR(spicc->core)) { 831 dev_err(&pdev->dev, "core clock request failed\n"); 832 ret = PTR_ERR(spicc->core); 833 goto out_host; 834 } 835 836 if (spicc->data->has_pclk) { 837 spicc->pclk = devm_clk_get_enabled(&pdev->dev, "pclk"); 838 if (IS_ERR(spicc->pclk)) { 839 dev_err(&pdev->dev, "pclk clock request failed\n"); 840 ret = PTR_ERR(spicc->pclk); 841 goto out_host; 842 } 843 } 844 845 spicc->pinctrl = devm_pinctrl_get(&pdev->dev); 846 if (IS_ERR(spicc->pinctrl)) { 847 ret = PTR_ERR(spicc->pinctrl); 848 goto out_host; 849 } 850 851 device_reset_optional(&pdev->dev); 852 853 host->num_chipselect = 4; 854 host->dev.of_node = pdev->dev.of_node; 855 host->mode_bits = SPI_CPHA | SPI_CPOL | SPI_CS_HIGH | SPI_LOOP; 856 host->bits_per_word_mask = SPI_BPW_MASK(32) | 857 SPI_BPW_MASK(24) | 858 SPI_BPW_MASK(16) | 859 SPI_BPW_MASK(8); 860 host->flags = (SPI_CONTROLLER_MUST_RX | SPI_CONTROLLER_MUST_TX); 861 host->min_speed_hz = spicc->data->min_speed_hz; 862 host->max_speed_hz = spicc->data->max_speed_hz; 863 host->setup = meson_spicc_setup; 864 host->cleanup = meson_spicc_cleanup; 865 host->prepare_message = meson_spicc_prepare_message; 866 host->unprepare_transfer_hardware = meson_spicc_unprepare_transfer; 867 host->transfer_one = meson_spicc_transfer_one; 868 host->use_gpio_descriptors = true; 869 870 meson_spicc_oen_enable(spicc); 871 872 ret = meson_spicc_pow2_clk_init(spicc); 873 if (ret) { 874 dev_err(&pdev->dev, "pow2 clock registration failed\n"); 875 goto out_host; 876 } 877 878 if (spicc->data->has_enhance_clk_div) { 879 ret = meson_spicc_enh_clk_init(spicc); 880 if (ret) { 881 dev_err(&pdev->dev, "clock registration failed\n"); 882 goto out_host; 883 } 884 } 885 886 ret = devm_spi_register_controller(&pdev->dev, host); 887 if (ret) { 888 dev_err(&pdev->dev, "spi registration failed\n"); 889 goto out_host; 890 } 891 892 return 0; 893 894 out_host: 895 spi_controller_put(host); 896 897 return ret; 898 } 899 900 static void meson_spicc_remove(struct platform_device *pdev) 901 { 902 struct meson_spicc_device *spicc = platform_get_drvdata(pdev); 903 904 /* Disable SPI */ 905 writel(0, spicc->base + SPICC_CONREG); 906 907 spi_controller_put(spicc->host); 908 } 909 910 static const struct meson_spicc_data meson_spicc_gx_data = { 911 .max_speed_hz = 30000000, 912 .min_speed_hz = 325000, 913 .fifo_size = 16, 914 }; 915 916 static const struct meson_spicc_data meson_spicc_axg_data = { 917 .max_speed_hz = 80000000, 918 .min_speed_hz = 325000, 919 .fifo_size = 16, 920 .has_oen = true, 921 .has_enhance_clk_div = true, 922 }; 923 924 static const struct meson_spicc_data meson_spicc_g12a_data = { 925 .max_speed_hz = 166666666, 926 .min_speed_hz = 50000, 927 .fifo_size = 15, 928 .has_oen = true, 929 .has_enhance_clk_div = true, 930 .has_pclk = true, 931 }; 932 933 static const struct of_device_id meson_spicc_of_match[] = { 934 { 935 .compatible = "amlogic,meson-gx-spicc", 936 .data = &meson_spicc_gx_data, 937 }, 938 { 939 .compatible = "amlogic,meson-axg-spicc", 940 .data = &meson_spicc_axg_data, 941 }, 942 { 943 .compatible = "amlogic,meson-g12a-spicc", 944 .data = &meson_spicc_g12a_data, 945 }, 946 { /* sentinel */ } 947 }; 948 MODULE_DEVICE_TABLE(of, meson_spicc_of_match); 949 950 static struct platform_driver meson_spicc_driver = { 951 .probe = meson_spicc_probe, 952 .remove_new = meson_spicc_remove, 953 .driver = { 954 .name = "meson-spicc", 955 .of_match_table = of_match_ptr(meson_spicc_of_match), 956 }, 957 }; 958 959 module_platform_driver(meson_spicc_driver); 960 961 MODULE_DESCRIPTION("Meson SPI Communication Controller driver"); 962 MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); 963 MODULE_LICENSE("GPL"); 964