1 // SPDX-License-Identifier: GPL-2.0-only 2 // 3 // Copyright (C) 2020 BAIKAL ELECTRONICS, JSC 4 // 5 // Authors: 6 // Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> 7 // Serge Semin <Sergey.Semin@baikalelectronics.ru> 8 // 9 // Baikal-T1 DW APB SPI and System Boot SPI driver 10 // 11 12 #include <linux/clk.h> 13 #include <linux/cpumask.h> 14 #include <linux/err.h> 15 #include <linux/interrupt.h> 16 #include <linux/module.h> 17 #include <linux/mux/consumer.h> 18 #include <linux/of.h> 19 #include <linux/of_platform.h> 20 #include <linux/platform_device.h> 21 #include <linux/pm_runtime.h> 22 #include <linux/property.h> 23 #include <linux/slab.h> 24 #include <linux/spi/spi-mem.h> 25 #include <linux/spi/spi.h> 26 27 #include "spi-dw.h" 28 29 #define BT1_BOOT_DIRMAP 0 30 #define BT1_BOOT_REGS 1 31 32 struct dw_spi_bt1 { 33 struct dw_spi dws; 34 struct clk *clk; 35 struct mux_control *mux; 36 37 #ifdef CONFIG_SPI_DW_BT1_DIRMAP 38 void __iomem *map; 39 resource_size_t map_len; 40 #endif 41 }; 42 #define to_dw_spi_bt1(_ctlr) \ 43 container_of(spi_controller_get_devdata(_ctlr), struct dw_spi_bt1, dws) 44 45 typedef int (*dw_spi_bt1_init_cb)(struct platform_device *pdev, 46 struct dw_spi_bt1 *dwsbt1); 47 48 #ifdef CONFIG_SPI_DW_BT1_DIRMAP 49 50 static int dw_spi_bt1_dirmap_create(struct spi_mem_dirmap_desc *desc) 51 { 52 struct dw_spi_bt1 *dwsbt1 = to_dw_spi_bt1(desc->mem->spi->controller); 53 54 if (!dwsbt1->map || 55 !dwsbt1->dws.mem_ops.supports_op(desc->mem, &desc->info.op_tmpl)) 56 return -EOPNOTSUPP; 57 58 if (desc->info.op_tmpl.data.dir != SPI_MEM_DATA_IN) 59 return -EOPNOTSUPP; 60 61 /* 62 * Make sure the requested region doesn't go out of the physically 63 * mapped flash memory bounds. 64 */ 65 if (desc->info.offset + desc->info.length > dwsbt1->map_len) 66 return -EINVAL; 67 68 return 0; 69 } 70 71 /* 72 * Directly mapped SPI memory region is only accessible in the dword chunks. 73 * That's why we have to create a dedicated read-method to copy data from there 74 * to the passed buffer. 75 */ 76 static void dw_spi_bt1_dirmap_copy_from_map(void *to, void __iomem *from, size_t len) 77 { 78 size_t shift, chunk; 79 u32 data; 80 81 /* 82 * We split the copying up into the next three stages: unaligned head, 83 * aligned body, unaligned tail. 84 */ 85 shift = (size_t)from & 0x3; 86 if (shift) { 87 chunk = min_t(size_t, 4 - shift, len); 88 data = readl_relaxed(from - shift); 89 memcpy(to, (char *)&data + shift, chunk); 90 from += chunk; 91 to += chunk; 92 len -= chunk; 93 } 94 95 while (len >= 4) { 96 data = readl_relaxed(from); 97 memcpy(to, &data, 4); 98 from += 4; 99 to += 4; 100 len -= 4; 101 } 102 103 if (len) { 104 data = readl_relaxed(from); 105 memcpy(to, &data, len); 106 } 107 } 108 109 static ssize_t dw_spi_bt1_dirmap_read(struct spi_mem_dirmap_desc *desc, 110 u64 offs, size_t len, void *buf) 111 { 112 struct dw_spi_bt1 *dwsbt1 = to_dw_spi_bt1(desc->mem->spi->controller); 113 struct dw_spi *dws = &dwsbt1->dws; 114 struct spi_mem *mem = desc->mem; 115 struct dw_spi_cfg cfg; 116 int ret; 117 118 /* 119 * Make sure the requested operation length is valid. Truncate the 120 * length if it's greater than the length of the MMIO region. 121 */ 122 if (offs >= dwsbt1->map_len || !len) 123 return 0; 124 125 len = min_t(size_t, len, dwsbt1->map_len - offs); 126 127 /* Collect the controller configuration required by the operation */ 128 cfg.tmode = DW_SPI_CTRLR0_TMOD_EPROMREAD; 129 cfg.dfs = 8; 130 cfg.ndf = 4; 131 cfg.freq = mem->spi->max_speed_hz; 132 133 /* Make sure the corresponding CS is de-asserted on transmission */ 134 dw_spi_set_cs(mem->spi, false); 135 136 dw_spi_enable_chip(dws, 0); 137 138 dw_spi_update_config(dws, mem->spi, &cfg); 139 140 dw_spi_umask_intr(dws, DW_SPI_INT_RXFI); 141 142 dw_spi_enable_chip(dws, 1); 143 144 /* 145 * Enable the transparent mode of the System Boot Controller. 146 * The SPI core IO should have been locked before calling this method 147 * so noone would be touching the controller' registers during the 148 * dirmap operation. 149 */ 150 ret = mux_control_select(dwsbt1->mux, BT1_BOOT_DIRMAP); 151 if (ret) 152 return ret; 153 154 dw_spi_bt1_dirmap_copy_from_map(buf, dwsbt1->map + offs, len); 155 156 mux_control_deselect(dwsbt1->mux); 157 158 dw_spi_set_cs(mem->spi, true); 159 160 ret = dw_spi_check_status(dws, true); 161 162 return ret ?: len; 163 } 164 165 #endif /* CONFIG_SPI_DW_BT1_DIRMAP */ 166 167 static int dw_spi_bt1_std_init(struct platform_device *pdev, 168 struct dw_spi_bt1 *dwsbt1) 169 { 170 struct dw_spi *dws = &dwsbt1->dws; 171 172 dws->irq = platform_get_irq(pdev, 0); 173 if (dws->irq < 0) 174 return dws->irq; 175 176 dws->num_cs = 4; 177 178 /* 179 * Baikal-T1 Normal SPI Controllers don't always keep up with full SPI 180 * bus speed especially when it comes to the concurrent access to the 181 * APB bus resources. Thus we have no choice but to set a constraint on 182 * the SPI bus frequency for the memory operations which require to 183 * read/write data as fast as possible. 184 */ 185 dws->max_mem_freq = 20000000U; 186 187 dw_spi_dma_setup_generic(dws); 188 189 return 0; 190 } 191 192 static int dw_spi_bt1_sys_init(struct platform_device *pdev, 193 struct dw_spi_bt1 *dwsbt1) 194 { 195 struct resource *mem __maybe_unused; 196 struct dw_spi *dws = &dwsbt1->dws; 197 198 /* 199 * Baikal-T1 System Boot Controller is equipped with a mux, which 200 * switches between the directly mapped SPI flash access mode and 201 * IO access to the DW APB SSI registers. Note the mux controller 202 * must be setup to preserve the registers being accessible by default 203 * (on idle-state). 204 */ 205 dwsbt1->mux = devm_mux_control_get(&pdev->dev, NULL); 206 if (IS_ERR(dwsbt1->mux)) 207 return PTR_ERR(dwsbt1->mux); 208 209 /* 210 * Directly mapped SPI flash memory is a 16MB MMIO region, which can be 211 * used to access a peripheral memory device just by reading/writing 212 * data from/to it. Note the system APB bus will stall during each IO 213 * from/to the dirmap region until the operation is finished. So don't 214 * use it concurrently with time-critical tasks (like the SPI memory 215 * operations implemented in the DW APB SSI driver). 216 */ 217 #ifdef CONFIG_SPI_DW_BT1_DIRMAP 218 mem = platform_get_resource(pdev, IORESOURCE_MEM, 1); 219 if (mem) { 220 dwsbt1->map = devm_ioremap_resource(&pdev->dev, mem); 221 if (!IS_ERR(dwsbt1->map)) { 222 dwsbt1->map_len = resource_size(mem); 223 dws->mem_ops.dirmap_create = dw_spi_bt1_dirmap_create; 224 dws->mem_ops.dirmap_read = dw_spi_bt1_dirmap_read; 225 } else { 226 dwsbt1->map = NULL; 227 } 228 } 229 #endif /* CONFIG_SPI_DW_BT1_DIRMAP */ 230 231 /* 232 * There is no IRQ, no DMA and just one CS available on the System Boot 233 * SPI controller. 234 */ 235 dws->irq = IRQ_NOTCONNECTED; 236 dws->num_cs = 1; 237 238 /* 239 * Baikal-T1 System Boot SPI Controller doesn't keep up with the full 240 * SPI bus speed due to relatively slow APB bus and races for it' 241 * resources from different CPUs. The situation is worsen by a small 242 * FIFOs depth (just 8 words). It works better in a single CPU mode 243 * though, but still tends to be not fast enough at low CPU 244 * frequencies. 245 */ 246 if (num_possible_cpus() > 1) 247 dws->max_mem_freq = 10000000U; 248 else 249 dws->max_mem_freq = 20000000U; 250 251 return 0; 252 } 253 254 static int dw_spi_bt1_probe(struct platform_device *pdev) 255 { 256 dw_spi_bt1_init_cb init_func; 257 struct dw_spi_bt1 *dwsbt1; 258 struct resource *mem; 259 struct dw_spi *dws; 260 int ret; 261 262 dwsbt1 = devm_kzalloc(&pdev->dev, sizeof(struct dw_spi_bt1), GFP_KERNEL); 263 if (!dwsbt1) 264 return -ENOMEM; 265 266 dws = &dwsbt1->dws; 267 268 dws->regs = devm_platform_get_and_ioremap_resource(pdev, 0, &mem); 269 if (IS_ERR(dws->regs)) 270 return PTR_ERR(dws->regs); 271 272 dws->paddr = mem->start; 273 274 dwsbt1->clk = devm_clk_get_enabled(&pdev->dev, NULL); 275 if (IS_ERR(dwsbt1->clk)) 276 return PTR_ERR(dwsbt1->clk); 277 278 dws->bus_num = pdev->id; 279 dws->reg_io_width = 4; 280 dws->max_freq = clk_get_rate(dwsbt1->clk); 281 if (!dws->max_freq) 282 return -EINVAL; 283 284 init_func = device_get_match_data(&pdev->dev); 285 ret = init_func(pdev, dwsbt1); 286 if (ret) 287 return ret; 288 289 pm_runtime_enable(&pdev->dev); 290 291 ret = dw_spi_add_host(&pdev->dev, dws); 292 if (ret) { 293 pm_runtime_disable(&pdev->dev); 294 return ret; 295 } 296 297 platform_set_drvdata(pdev, dwsbt1); 298 299 return 0; 300 } 301 302 static void dw_spi_bt1_remove(struct platform_device *pdev) 303 { 304 struct dw_spi_bt1 *dwsbt1 = platform_get_drvdata(pdev); 305 306 dw_spi_remove_host(&dwsbt1->dws); 307 308 pm_runtime_disable(&pdev->dev); 309 } 310 311 static const struct of_device_id dw_spi_bt1_of_match[] = { 312 { .compatible = "baikal,bt1-ssi", .data = dw_spi_bt1_std_init}, 313 { .compatible = "baikal,bt1-sys-ssi", .data = dw_spi_bt1_sys_init}, 314 { } 315 }; 316 MODULE_DEVICE_TABLE(of, dw_spi_bt1_of_match); 317 318 static struct platform_driver dw_spi_bt1_driver = { 319 .probe = dw_spi_bt1_probe, 320 .remove = dw_spi_bt1_remove, 321 .driver = { 322 .name = "bt1-sys-ssi", 323 .of_match_table = dw_spi_bt1_of_match, 324 }, 325 }; 326 module_platform_driver(dw_spi_bt1_driver); 327 328 MODULE_AUTHOR("Serge Semin <Sergey.Semin@baikalelectronics.ru>"); 329 MODULE_DESCRIPTION("Baikal-T1 System Boot SPI Controller driver"); 330 MODULE_LICENSE("GPL v2"); 331 MODULE_IMPORT_NS(SPI_DW_CORE); 332