1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Driver for Atmel QSPI Controller 4 * 5 * Copyright (C) 2015 Atmel Corporation 6 * Copyright (C) 2018 Cryptera A/S 7 * 8 * Author: Cyrille Pitchen <cyrille.pitchen@atmel.com> 9 * Author: Piotr Bugalski <bugalski.piotr@gmail.com> 10 * 11 * This driver is based on drivers/mtd/spi-nor/fsl-quadspi.c from Freescale. 12 */ 13 14 #include <linux/clk.h> 15 #include <linux/delay.h> 16 #include <linux/err.h> 17 #include <linux/interrupt.h> 18 #include <linux/io.h> 19 #include <linux/kernel.h> 20 #include <linux/module.h> 21 #include <linux/of.h> 22 #include <linux/of_platform.h> 23 #include <linux/platform_device.h> 24 #include <linux/pm_runtime.h> 25 #include <linux/spi/spi-mem.h> 26 27 /* QSPI register offsets */ 28 #define QSPI_CR 0x0000 /* Control Register */ 29 #define QSPI_MR 0x0004 /* Mode Register */ 30 #define QSPI_RD 0x0008 /* Receive Data Register */ 31 #define QSPI_TD 0x000c /* Transmit Data Register */ 32 #define QSPI_SR 0x0010 /* Status Register */ 33 #define QSPI_IER 0x0014 /* Interrupt Enable Register */ 34 #define QSPI_IDR 0x0018 /* Interrupt Disable Register */ 35 #define QSPI_IMR 0x001c /* Interrupt Mask Register */ 36 #define QSPI_SCR 0x0020 /* Serial Clock Register */ 37 38 #define QSPI_IAR 0x0030 /* Instruction Address Register */ 39 #define QSPI_ICR 0x0034 /* Instruction Code Register */ 40 #define QSPI_WICR 0x0034 /* Write Instruction Code Register */ 41 #define QSPI_IFR 0x0038 /* Instruction Frame Register */ 42 #define QSPI_RICR 0x003C /* Read Instruction Code Register */ 43 44 #define QSPI_SMR 0x0040 /* Scrambling Mode Register */ 45 #define QSPI_SKR 0x0044 /* Scrambling Key Register */ 46 47 #define QSPI_WPMR 0x00E4 /* Write Protection Mode Register */ 48 #define QSPI_WPSR 0x00E8 /* Write Protection Status Register */ 49 50 #define QSPI_VERSION 0x00FC /* Version Register */ 51 52 53 /* Bitfields in QSPI_CR (Control Register) */ 54 #define QSPI_CR_QSPIEN BIT(0) 55 #define QSPI_CR_QSPIDIS BIT(1) 56 #define QSPI_CR_SWRST BIT(7) 57 #define QSPI_CR_LASTXFER BIT(24) 58 59 /* Bitfields in QSPI_MR (Mode Register) */ 60 #define QSPI_MR_SMM BIT(0) 61 #define QSPI_MR_LLB BIT(1) 62 #define QSPI_MR_WDRBT BIT(2) 63 #define QSPI_MR_SMRM BIT(3) 64 #define QSPI_MR_CSMODE_MASK GENMASK(5, 4) 65 #define QSPI_MR_CSMODE_NOT_RELOADED (0 << 4) 66 #define QSPI_MR_CSMODE_LASTXFER (1 << 4) 67 #define QSPI_MR_CSMODE_SYSTEMATICALLY (2 << 4) 68 #define QSPI_MR_NBBITS_MASK GENMASK(11, 8) 69 #define QSPI_MR_NBBITS(n) ((((n) - 8) << 8) & QSPI_MR_NBBITS_MASK) 70 #define QSPI_MR_DLYBCT_MASK GENMASK(23, 16) 71 #define QSPI_MR_DLYBCT(n) (((n) << 16) & QSPI_MR_DLYBCT_MASK) 72 #define QSPI_MR_DLYCS_MASK GENMASK(31, 24) 73 #define QSPI_MR_DLYCS(n) (((n) << 24) & QSPI_MR_DLYCS_MASK) 74 75 /* Bitfields in QSPI_SR/QSPI_IER/QSPI_IDR/QSPI_IMR */ 76 #define QSPI_SR_RDRF BIT(0) 77 #define QSPI_SR_TDRE BIT(1) 78 #define QSPI_SR_TXEMPTY BIT(2) 79 #define QSPI_SR_OVRES BIT(3) 80 #define QSPI_SR_CSR BIT(8) 81 #define QSPI_SR_CSS BIT(9) 82 #define QSPI_SR_INSTRE BIT(10) 83 #define QSPI_SR_QSPIENS BIT(24) 84 85 #define QSPI_SR_CMD_COMPLETED (QSPI_SR_INSTRE | QSPI_SR_CSR) 86 87 /* Bitfields in QSPI_SCR (Serial Clock Register) */ 88 #define QSPI_SCR_CPOL BIT(0) 89 #define QSPI_SCR_CPHA BIT(1) 90 #define QSPI_SCR_SCBR_MASK GENMASK(15, 8) 91 #define QSPI_SCR_SCBR(n) (((n) << 8) & QSPI_SCR_SCBR_MASK) 92 #define QSPI_SCR_DLYBS_MASK GENMASK(23, 16) 93 #define QSPI_SCR_DLYBS(n) (((n) << 16) & QSPI_SCR_DLYBS_MASK) 94 95 /* Bitfields in QSPI_ICR (Read/Write Instruction Code Register) */ 96 #define QSPI_ICR_INST_MASK GENMASK(7, 0) 97 #define QSPI_ICR_INST(inst) (((inst) << 0) & QSPI_ICR_INST_MASK) 98 #define QSPI_ICR_OPT_MASK GENMASK(23, 16) 99 #define QSPI_ICR_OPT(opt) (((opt) << 16) & QSPI_ICR_OPT_MASK) 100 101 /* Bitfields in QSPI_IFR (Instruction Frame Register) */ 102 #define QSPI_IFR_WIDTH_MASK GENMASK(2, 0) 103 #define QSPI_IFR_WIDTH_SINGLE_BIT_SPI (0 << 0) 104 #define QSPI_IFR_WIDTH_DUAL_OUTPUT (1 << 0) 105 #define QSPI_IFR_WIDTH_QUAD_OUTPUT (2 << 0) 106 #define QSPI_IFR_WIDTH_DUAL_IO (3 << 0) 107 #define QSPI_IFR_WIDTH_QUAD_IO (4 << 0) 108 #define QSPI_IFR_WIDTH_DUAL_CMD (5 << 0) 109 #define QSPI_IFR_WIDTH_QUAD_CMD (6 << 0) 110 #define QSPI_IFR_INSTEN BIT(4) 111 #define QSPI_IFR_ADDREN BIT(5) 112 #define QSPI_IFR_OPTEN BIT(6) 113 #define QSPI_IFR_DATAEN BIT(7) 114 #define QSPI_IFR_OPTL_MASK GENMASK(9, 8) 115 #define QSPI_IFR_OPTL_1BIT (0 << 8) 116 #define QSPI_IFR_OPTL_2BIT (1 << 8) 117 #define QSPI_IFR_OPTL_4BIT (2 << 8) 118 #define QSPI_IFR_OPTL_8BIT (3 << 8) 119 #define QSPI_IFR_ADDRL BIT(10) 120 #define QSPI_IFR_TFRTYP_MEM BIT(12) 121 #define QSPI_IFR_SAMA5D2_WRITE_TRSFR BIT(13) 122 #define QSPI_IFR_CRM BIT(14) 123 #define QSPI_IFR_NBDUM_MASK GENMASK(20, 16) 124 #define QSPI_IFR_NBDUM(n) (((n) << 16) & QSPI_IFR_NBDUM_MASK) 125 #define QSPI_IFR_APBTFRTYP_READ BIT(24) /* Defined in SAM9X60 */ 126 127 /* Bitfields in QSPI_SMR (Scrambling Mode Register) */ 128 #define QSPI_SMR_SCREN BIT(0) 129 #define QSPI_SMR_RVDIS BIT(1) 130 131 /* Bitfields in QSPI_WPMR (Write Protection Mode Register) */ 132 #define QSPI_WPMR_WPEN BIT(0) 133 #define QSPI_WPMR_WPKEY_MASK GENMASK(31, 8) 134 #define QSPI_WPMR_WPKEY(wpkey) (((wpkey) << 8) & QSPI_WPMR_WPKEY_MASK) 135 136 /* Bitfields in QSPI_WPSR (Write Protection Status Register) */ 137 #define QSPI_WPSR_WPVS BIT(0) 138 #define QSPI_WPSR_WPVSRC_MASK GENMASK(15, 8) 139 #define QSPI_WPSR_WPVSRC(src) (((src) << 8) & QSPI_WPSR_WPVSRC) 140 141 struct atmel_qspi_caps { 142 bool has_qspick; 143 bool has_ricr; 144 }; 145 146 struct atmel_qspi { 147 void __iomem *regs; 148 void __iomem *mem; 149 struct clk *pclk; 150 struct clk *qspick; 151 struct platform_device *pdev; 152 const struct atmel_qspi_caps *caps; 153 resource_size_t mmap_size; 154 u32 pending; 155 u32 mr; 156 u32 scr; 157 struct completion cmd_completion; 158 }; 159 160 struct atmel_qspi_mode { 161 u8 cmd_buswidth; 162 u8 addr_buswidth; 163 u8 data_buswidth; 164 u32 config; 165 }; 166 167 static const struct atmel_qspi_mode atmel_qspi_modes[] = { 168 { 1, 1, 1, QSPI_IFR_WIDTH_SINGLE_BIT_SPI }, 169 { 1, 1, 2, QSPI_IFR_WIDTH_DUAL_OUTPUT }, 170 { 1, 1, 4, QSPI_IFR_WIDTH_QUAD_OUTPUT }, 171 { 1, 2, 2, QSPI_IFR_WIDTH_DUAL_IO }, 172 { 1, 4, 4, QSPI_IFR_WIDTH_QUAD_IO }, 173 { 2, 2, 2, QSPI_IFR_WIDTH_DUAL_CMD }, 174 { 4, 4, 4, QSPI_IFR_WIDTH_QUAD_CMD }, 175 }; 176 177 #ifdef VERBOSE_DEBUG 178 static const char *atmel_qspi_reg_name(u32 offset, char *tmp, size_t sz) 179 { 180 switch (offset) { 181 case QSPI_CR: 182 return "CR"; 183 case QSPI_MR: 184 return "MR"; 185 case QSPI_RD: 186 return "MR"; 187 case QSPI_TD: 188 return "TD"; 189 case QSPI_SR: 190 return "SR"; 191 case QSPI_IER: 192 return "IER"; 193 case QSPI_IDR: 194 return "IDR"; 195 case QSPI_IMR: 196 return "IMR"; 197 case QSPI_SCR: 198 return "SCR"; 199 case QSPI_IAR: 200 return "IAR"; 201 case QSPI_ICR: 202 return "ICR/WICR"; 203 case QSPI_IFR: 204 return "IFR"; 205 case QSPI_RICR: 206 return "RICR"; 207 case QSPI_SMR: 208 return "SMR"; 209 case QSPI_SKR: 210 return "SKR"; 211 case QSPI_WPMR: 212 return "WPMR"; 213 case QSPI_WPSR: 214 return "WPSR"; 215 case QSPI_VERSION: 216 return "VERSION"; 217 default: 218 snprintf(tmp, sz, "0x%02x", offset); 219 break; 220 } 221 222 return tmp; 223 } 224 #endif /* VERBOSE_DEBUG */ 225 226 static u32 atmel_qspi_read(struct atmel_qspi *aq, u32 offset) 227 { 228 u32 value = readl_relaxed(aq->regs + offset); 229 230 #ifdef VERBOSE_DEBUG 231 char tmp[8]; 232 233 dev_vdbg(&aq->pdev->dev, "read 0x%08x from %s\n", value, 234 atmel_qspi_reg_name(offset, tmp, sizeof(tmp))); 235 #endif /* VERBOSE_DEBUG */ 236 237 return value; 238 } 239 240 static void atmel_qspi_write(u32 value, struct atmel_qspi *aq, u32 offset) 241 { 242 #ifdef VERBOSE_DEBUG 243 char tmp[8]; 244 245 dev_vdbg(&aq->pdev->dev, "write 0x%08x into %s\n", value, 246 atmel_qspi_reg_name(offset, tmp, sizeof(tmp))); 247 #endif /* VERBOSE_DEBUG */ 248 249 writel_relaxed(value, aq->regs + offset); 250 } 251 252 static inline bool atmel_qspi_is_compatible(const struct spi_mem_op *op, 253 const struct atmel_qspi_mode *mode) 254 { 255 if (op->cmd.buswidth != mode->cmd_buswidth) 256 return false; 257 258 if (op->addr.nbytes && op->addr.buswidth != mode->addr_buswidth) 259 return false; 260 261 if (op->data.nbytes && op->data.buswidth != mode->data_buswidth) 262 return false; 263 264 return true; 265 } 266 267 static int atmel_qspi_find_mode(const struct spi_mem_op *op) 268 { 269 u32 i; 270 271 for (i = 0; i < ARRAY_SIZE(atmel_qspi_modes); i++) 272 if (atmel_qspi_is_compatible(op, &atmel_qspi_modes[i])) 273 return i; 274 275 return -EOPNOTSUPP; 276 } 277 278 static bool atmel_qspi_supports_op(struct spi_mem *mem, 279 const struct spi_mem_op *op) 280 { 281 if (!spi_mem_default_supports_op(mem, op)) 282 return false; 283 284 if (atmel_qspi_find_mode(op) < 0) 285 return false; 286 287 /* special case not supported by hardware */ 288 if (op->addr.nbytes == 2 && op->cmd.buswidth != op->addr.buswidth && 289 op->dummy.nbytes == 0) 290 return false; 291 292 return true; 293 } 294 295 static int atmel_qspi_set_cfg(struct atmel_qspi *aq, 296 const struct spi_mem_op *op, u32 *offset) 297 { 298 u32 iar, icr, ifr; 299 u32 dummy_cycles = 0; 300 int mode; 301 302 iar = 0; 303 icr = QSPI_ICR_INST(op->cmd.opcode); 304 ifr = QSPI_IFR_INSTEN; 305 306 mode = atmel_qspi_find_mode(op); 307 if (mode < 0) 308 return mode; 309 ifr |= atmel_qspi_modes[mode].config; 310 311 if (op->dummy.nbytes) 312 dummy_cycles = op->dummy.nbytes * 8 / op->dummy.buswidth; 313 314 /* 315 * The controller allows 24 and 32-bit addressing while NAND-flash 316 * requires 16-bit long. Handling 8-bit long addresses is done using 317 * the option field. For the 16-bit addresses, the workaround depends 318 * of the number of requested dummy bits. If there are 8 or more dummy 319 * cycles, the address is shifted and sent with the first dummy byte. 320 * Otherwise opcode is disabled and the first byte of the address 321 * contains the command opcode (works only if the opcode and address 322 * use the same buswidth). The limitation is when the 16-bit address is 323 * used without enough dummy cycles and the opcode is using a different 324 * buswidth than the address. 325 */ 326 if (op->addr.buswidth) { 327 switch (op->addr.nbytes) { 328 case 0: 329 break; 330 case 1: 331 ifr |= QSPI_IFR_OPTEN | QSPI_IFR_OPTL_8BIT; 332 icr |= QSPI_ICR_OPT(op->addr.val & 0xff); 333 break; 334 case 2: 335 if (dummy_cycles < 8 / op->addr.buswidth) { 336 ifr &= ~QSPI_IFR_INSTEN; 337 ifr |= QSPI_IFR_ADDREN; 338 iar = (op->cmd.opcode << 16) | 339 (op->addr.val & 0xffff); 340 } else { 341 ifr |= QSPI_IFR_ADDREN; 342 iar = (op->addr.val << 8) & 0xffffff; 343 dummy_cycles -= 8 / op->addr.buswidth; 344 } 345 break; 346 case 3: 347 ifr |= QSPI_IFR_ADDREN; 348 iar = op->addr.val & 0xffffff; 349 break; 350 case 4: 351 ifr |= QSPI_IFR_ADDREN | QSPI_IFR_ADDRL; 352 iar = op->addr.val & 0x7ffffff; 353 break; 354 default: 355 return -ENOTSUPP; 356 } 357 } 358 359 /* offset of the data access in the QSPI memory space */ 360 *offset = iar; 361 362 /* Set number of dummy cycles */ 363 if (dummy_cycles) 364 ifr |= QSPI_IFR_NBDUM(dummy_cycles); 365 366 /* Set data enable and data transfer type. */ 367 if (op->data.nbytes) { 368 ifr |= QSPI_IFR_DATAEN; 369 370 if (op->addr.nbytes) 371 ifr |= QSPI_IFR_TFRTYP_MEM; 372 } 373 374 /* 375 * If the QSPI controller is set in regular SPI mode, set it in 376 * Serial Memory Mode (SMM). 377 */ 378 if (aq->mr != QSPI_MR_SMM) { 379 atmel_qspi_write(QSPI_MR_SMM, aq, QSPI_MR); 380 aq->mr = QSPI_MR_SMM; 381 } 382 383 /* Clear pending interrupts */ 384 (void)atmel_qspi_read(aq, QSPI_SR); 385 386 /* Set QSPI Instruction Frame registers. */ 387 if (op->addr.nbytes && !op->data.nbytes) 388 atmel_qspi_write(iar, aq, QSPI_IAR); 389 390 if (aq->caps->has_ricr) { 391 if (op->data.dir == SPI_MEM_DATA_IN) 392 atmel_qspi_write(icr, aq, QSPI_RICR); 393 else 394 atmel_qspi_write(icr, aq, QSPI_WICR); 395 } else { 396 if (op->data.nbytes && op->data.dir == SPI_MEM_DATA_OUT) 397 ifr |= QSPI_IFR_SAMA5D2_WRITE_TRSFR; 398 399 atmel_qspi_write(icr, aq, QSPI_ICR); 400 } 401 402 atmel_qspi_write(ifr, aq, QSPI_IFR); 403 404 return 0; 405 } 406 407 static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op) 408 { 409 struct atmel_qspi *aq = spi_controller_get_devdata(mem->spi->controller); 410 u32 sr, offset; 411 int err; 412 413 /* 414 * Check if the address exceeds the MMIO window size. An improvement 415 * would be to add support for regular SPI mode and fall back to it 416 * when the flash memories overrun the controller's memory space. 417 */ 418 if (op->addr.val + op->data.nbytes > aq->mmap_size) 419 return -ENOTSUPP; 420 421 err = pm_runtime_resume_and_get(&aq->pdev->dev); 422 if (err < 0) 423 return err; 424 425 err = atmel_qspi_set_cfg(aq, op, &offset); 426 if (err) 427 goto pm_runtime_put; 428 429 /* Skip to the final steps if there is no data */ 430 if (op->data.nbytes) { 431 /* Dummy read of QSPI_IFR to synchronize APB and AHB accesses */ 432 (void)atmel_qspi_read(aq, QSPI_IFR); 433 434 /* Send/Receive data */ 435 if (op->data.dir == SPI_MEM_DATA_IN) 436 memcpy_fromio(op->data.buf.in, aq->mem + offset, 437 op->data.nbytes); 438 else 439 memcpy_toio(aq->mem + offset, op->data.buf.out, 440 op->data.nbytes); 441 442 /* Release the chip-select */ 443 atmel_qspi_write(QSPI_CR_LASTXFER, aq, QSPI_CR); 444 } 445 446 /* Poll INSTRuction End status */ 447 sr = atmel_qspi_read(aq, QSPI_SR); 448 if ((sr & QSPI_SR_CMD_COMPLETED) == QSPI_SR_CMD_COMPLETED) 449 goto pm_runtime_put; 450 451 /* Wait for INSTRuction End interrupt */ 452 reinit_completion(&aq->cmd_completion); 453 aq->pending = sr & QSPI_SR_CMD_COMPLETED; 454 atmel_qspi_write(QSPI_SR_CMD_COMPLETED, aq, QSPI_IER); 455 if (!wait_for_completion_timeout(&aq->cmd_completion, 456 msecs_to_jiffies(1000))) 457 err = -ETIMEDOUT; 458 atmel_qspi_write(QSPI_SR_CMD_COMPLETED, aq, QSPI_IDR); 459 460 pm_runtime_put: 461 pm_runtime_mark_last_busy(&aq->pdev->dev); 462 pm_runtime_put_autosuspend(&aq->pdev->dev); 463 return err; 464 } 465 466 static const char *atmel_qspi_get_name(struct spi_mem *spimem) 467 { 468 return dev_name(spimem->spi->dev.parent); 469 } 470 471 static const struct spi_controller_mem_ops atmel_qspi_mem_ops = { 472 .supports_op = atmel_qspi_supports_op, 473 .exec_op = atmel_qspi_exec_op, 474 .get_name = atmel_qspi_get_name 475 }; 476 477 static int atmel_qspi_setup(struct spi_device *spi) 478 { 479 struct spi_controller *ctrl = spi->controller; 480 struct atmel_qspi *aq = spi_controller_get_devdata(ctrl); 481 unsigned long src_rate; 482 u32 scbr; 483 int ret; 484 485 if (ctrl->busy) 486 return -EBUSY; 487 488 if (!spi->max_speed_hz) 489 return -EINVAL; 490 491 src_rate = clk_get_rate(aq->pclk); 492 if (!src_rate) 493 return -EINVAL; 494 495 /* Compute the QSPI baudrate */ 496 scbr = DIV_ROUND_UP(src_rate, spi->max_speed_hz); 497 if (scbr > 0) 498 scbr--; 499 500 ret = pm_runtime_resume_and_get(ctrl->dev.parent); 501 if (ret < 0) 502 return ret; 503 504 aq->scr = QSPI_SCR_SCBR(scbr); 505 atmel_qspi_write(aq->scr, aq, QSPI_SCR); 506 507 pm_runtime_mark_last_busy(ctrl->dev.parent); 508 pm_runtime_put_autosuspend(ctrl->dev.parent); 509 510 return 0; 511 } 512 513 static int atmel_qspi_set_cs_timing(struct spi_device *spi) 514 { 515 struct spi_controller *ctrl = spi->controller; 516 struct atmel_qspi *aq = spi_controller_get_devdata(ctrl); 517 unsigned long clk_rate; 518 u32 cs_setup; 519 int delay; 520 int ret; 521 522 delay = spi_delay_to_ns(&spi->cs_setup, NULL); 523 if (delay <= 0) 524 return delay; 525 526 clk_rate = clk_get_rate(aq->pclk); 527 if (!clk_rate) 528 return -EINVAL; 529 530 cs_setup = DIV_ROUND_UP((delay * DIV_ROUND_UP(clk_rate, 1000000)), 531 1000); 532 533 ret = pm_runtime_resume_and_get(ctrl->dev.parent); 534 if (ret < 0) 535 return ret; 536 537 aq->scr |= QSPI_SCR_DLYBS(cs_setup); 538 atmel_qspi_write(aq->scr, aq, QSPI_SCR); 539 540 pm_runtime_mark_last_busy(ctrl->dev.parent); 541 pm_runtime_put_autosuspend(ctrl->dev.parent); 542 543 return 0; 544 } 545 546 static void atmel_qspi_init(struct atmel_qspi *aq) 547 { 548 /* Reset the QSPI controller */ 549 atmel_qspi_write(QSPI_CR_SWRST, aq, QSPI_CR); 550 551 /* Set the QSPI controller by default in Serial Memory Mode */ 552 atmel_qspi_write(QSPI_MR_SMM, aq, QSPI_MR); 553 aq->mr = QSPI_MR_SMM; 554 555 /* Enable the QSPI controller */ 556 atmel_qspi_write(QSPI_CR_QSPIEN, aq, QSPI_CR); 557 } 558 559 static irqreturn_t atmel_qspi_interrupt(int irq, void *dev_id) 560 { 561 struct atmel_qspi *aq = dev_id; 562 u32 status, mask, pending; 563 564 status = atmel_qspi_read(aq, QSPI_SR); 565 mask = atmel_qspi_read(aq, QSPI_IMR); 566 pending = status & mask; 567 568 if (!pending) 569 return IRQ_NONE; 570 571 aq->pending |= pending; 572 if ((aq->pending & QSPI_SR_CMD_COMPLETED) == QSPI_SR_CMD_COMPLETED) 573 complete(&aq->cmd_completion); 574 575 return IRQ_HANDLED; 576 } 577 578 static int atmel_qspi_probe(struct platform_device *pdev) 579 { 580 struct spi_controller *ctrl; 581 struct atmel_qspi *aq; 582 struct resource *res; 583 int irq, err = 0; 584 585 ctrl = devm_spi_alloc_host(&pdev->dev, sizeof(*aq)); 586 if (!ctrl) 587 return -ENOMEM; 588 589 ctrl->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD | SPI_TX_DUAL | SPI_TX_QUAD; 590 ctrl->setup = atmel_qspi_setup; 591 ctrl->set_cs_timing = atmel_qspi_set_cs_timing; 592 ctrl->bus_num = -1; 593 ctrl->mem_ops = &atmel_qspi_mem_ops; 594 ctrl->num_chipselect = 1; 595 ctrl->dev.of_node = pdev->dev.of_node; 596 platform_set_drvdata(pdev, ctrl); 597 598 aq = spi_controller_get_devdata(ctrl); 599 600 init_completion(&aq->cmd_completion); 601 aq->pdev = pdev; 602 603 /* Map the registers */ 604 aq->regs = devm_platform_ioremap_resource_byname(pdev, "qspi_base"); 605 if (IS_ERR(aq->regs)) 606 return dev_err_probe(&pdev->dev, PTR_ERR(aq->regs), 607 "missing registers\n"); 608 609 /* Map the AHB memory */ 610 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "qspi_mmap"); 611 aq->mem = devm_ioremap_resource(&pdev->dev, res); 612 if (IS_ERR(aq->mem)) 613 return dev_err_probe(&pdev->dev, PTR_ERR(aq->mem), 614 "missing AHB memory\n"); 615 616 aq->mmap_size = resource_size(res); 617 618 /* Get the peripheral clock */ 619 aq->pclk = devm_clk_get(&pdev->dev, "pclk"); 620 if (IS_ERR(aq->pclk)) 621 aq->pclk = devm_clk_get(&pdev->dev, NULL); 622 623 if (IS_ERR(aq->pclk)) 624 return dev_err_probe(&pdev->dev, PTR_ERR(aq->pclk), 625 "missing peripheral clock\n"); 626 627 /* Enable the peripheral clock */ 628 err = clk_prepare_enable(aq->pclk); 629 if (err) 630 return dev_err_probe(&pdev->dev, err, 631 "failed to enable the peripheral clock\n"); 632 633 aq->caps = of_device_get_match_data(&pdev->dev); 634 if (!aq->caps) { 635 dev_err(&pdev->dev, "Could not retrieve QSPI caps\n"); 636 err = -EINVAL; 637 goto disable_pclk; 638 } 639 640 if (aq->caps->has_qspick) { 641 /* Get the QSPI system clock */ 642 aq->qspick = devm_clk_get(&pdev->dev, "qspick"); 643 if (IS_ERR(aq->qspick)) { 644 dev_err(&pdev->dev, "missing system clock\n"); 645 err = PTR_ERR(aq->qspick); 646 goto disable_pclk; 647 } 648 649 /* Enable the QSPI system clock */ 650 err = clk_prepare_enable(aq->qspick); 651 if (err) { 652 dev_err(&pdev->dev, 653 "failed to enable the QSPI system clock\n"); 654 goto disable_pclk; 655 } 656 } 657 658 /* Request the IRQ */ 659 irq = platform_get_irq(pdev, 0); 660 if (irq < 0) { 661 err = irq; 662 goto disable_qspick; 663 } 664 err = devm_request_irq(&pdev->dev, irq, atmel_qspi_interrupt, 665 0, dev_name(&pdev->dev), aq); 666 if (err) 667 goto disable_qspick; 668 669 pm_runtime_set_autosuspend_delay(&pdev->dev, 500); 670 pm_runtime_use_autosuspend(&pdev->dev); 671 pm_runtime_set_active(&pdev->dev); 672 pm_runtime_enable(&pdev->dev); 673 pm_runtime_get_noresume(&pdev->dev); 674 675 atmel_qspi_init(aq); 676 677 err = spi_register_controller(ctrl); 678 if (err) { 679 pm_runtime_put_noidle(&pdev->dev); 680 pm_runtime_disable(&pdev->dev); 681 pm_runtime_set_suspended(&pdev->dev); 682 pm_runtime_dont_use_autosuspend(&pdev->dev); 683 goto disable_qspick; 684 } 685 pm_runtime_mark_last_busy(&pdev->dev); 686 pm_runtime_put_autosuspend(&pdev->dev); 687 688 return 0; 689 690 disable_qspick: 691 clk_disable_unprepare(aq->qspick); 692 disable_pclk: 693 clk_disable_unprepare(aq->pclk); 694 695 return err; 696 } 697 698 static void atmel_qspi_remove(struct platform_device *pdev) 699 { 700 struct spi_controller *ctrl = platform_get_drvdata(pdev); 701 struct atmel_qspi *aq = spi_controller_get_devdata(ctrl); 702 int ret; 703 704 spi_unregister_controller(ctrl); 705 706 ret = pm_runtime_get_sync(&pdev->dev); 707 if (ret >= 0) { 708 atmel_qspi_write(QSPI_CR_QSPIDIS, aq, QSPI_CR); 709 clk_disable(aq->qspick); 710 clk_disable(aq->pclk); 711 } else { 712 /* 713 * atmel_qspi_runtime_{suspend,resume} just disable and enable 714 * the two clks respectively. So after resume failed these are 715 * off, and we skip hardware access and disabling these clks again. 716 */ 717 dev_warn(&pdev->dev, "Failed to resume device on remove\n"); 718 } 719 720 clk_unprepare(aq->qspick); 721 clk_unprepare(aq->pclk); 722 723 pm_runtime_disable(&pdev->dev); 724 pm_runtime_put_noidle(&pdev->dev); 725 } 726 727 static int __maybe_unused atmel_qspi_suspend(struct device *dev) 728 { 729 struct spi_controller *ctrl = dev_get_drvdata(dev); 730 struct atmel_qspi *aq = spi_controller_get_devdata(ctrl); 731 int ret; 732 733 ret = pm_runtime_resume_and_get(dev); 734 if (ret < 0) 735 return ret; 736 737 atmel_qspi_write(QSPI_CR_QSPIDIS, aq, QSPI_CR); 738 739 pm_runtime_mark_last_busy(dev); 740 pm_runtime_force_suspend(dev); 741 742 clk_unprepare(aq->qspick); 743 clk_unprepare(aq->pclk); 744 745 return 0; 746 } 747 748 static int __maybe_unused atmel_qspi_resume(struct device *dev) 749 { 750 struct spi_controller *ctrl = dev_get_drvdata(dev); 751 struct atmel_qspi *aq = spi_controller_get_devdata(ctrl); 752 int ret; 753 754 ret = clk_prepare(aq->pclk); 755 if (ret) 756 return ret; 757 758 ret = clk_prepare(aq->qspick); 759 if (ret) { 760 clk_unprepare(aq->pclk); 761 return ret; 762 } 763 764 ret = pm_runtime_force_resume(dev); 765 if (ret < 0) 766 return ret; 767 768 atmel_qspi_init(aq); 769 770 atmel_qspi_write(aq->scr, aq, QSPI_SCR); 771 772 pm_runtime_mark_last_busy(dev); 773 pm_runtime_put_autosuspend(dev); 774 775 return 0; 776 } 777 778 static int __maybe_unused atmel_qspi_runtime_suspend(struct device *dev) 779 { 780 struct spi_controller *ctrl = dev_get_drvdata(dev); 781 struct atmel_qspi *aq = spi_controller_get_devdata(ctrl); 782 783 clk_disable(aq->qspick); 784 clk_disable(aq->pclk); 785 786 return 0; 787 } 788 789 static int __maybe_unused atmel_qspi_runtime_resume(struct device *dev) 790 { 791 struct spi_controller *ctrl = dev_get_drvdata(dev); 792 struct atmel_qspi *aq = spi_controller_get_devdata(ctrl); 793 int ret; 794 795 ret = clk_enable(aq->pclk); 796 if (ret) 797 return ret; 798 799 ret = clk_enable(aq->qspick); 800 if (ret) 801 clk_disable(aq->pclk); 802 803 return ret; 804 } 805 806 static const struct dev_pm_ops __maybe_unused atmel_qspi_pm_ops = { 807 SET_SYSTEM_SLEEP_PM_OPS(atmel_qspi_suspend, atmel_qspi_resume) 808 SET_RUNTIME_PM_OPS(atmel_qspi_runtime_suspend, 809 atmel_qspi_runtime_resume, NULL) 810 }; 811 812 static const struct atmel_qspi_caps atmel_sama5d2_qspi_caps = {}; 813 814 static const struct atmel_qspi_caps atmel_sam9x60_qspi_caps = { 815 .has_qspick = true, 816 .has_ricr = true, 817 }; 818 819 static const struct of_device_id atmel_qspi_dt_ids[] = { 820 { 821 .compatible = "atmel,sama5d2-qspi", 822 .data = &atmel_sama5d2_qspi_caps, 823 }, 824 { 825 .compatible = "microchip,sam9x60-qspi", 826 .data = &atmel_sam9x60_qspi_caps, 827 }, 828 { /* sentinel */ } 829 }; 830 831 MODULE_DEVICE_TABLE(of, atmel_qspi_dt_ids); 832 833 static struct platform_driver atmel_qspi_driver = { 834 .driver = { 835 .name = "atmel_qspi", 836 .of_match_table = atmel_qspi_dt_ids, 837 .pm = pm_ptr(&atmel_qspi_pm_ops), 838 }, 839 .probe = atmel_qspi_probe, 840 .remove_new = atmel_qspi_remove, 841 }; 842 module_platform_driver(atmel_qspi_driver); 843 844 MODULE_AUTHOR("Cyrille Pitchen <cyrille.pitchen@atmel.com>"); 845 MODULE_AUTHOR("Piotr Bugalski <bugalski.piotr@gmail.com"); 846 MODULE_DESCRIPTION("Atmel QSPI Controller driver"); 847 MODULE_LICENSE("GPL v2"); 848