1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Intel IXP4xx Network Processor Engine driver for Linux 4 * 5 * Copyright (C) 2007 Krzysztof Halasa <khc@pm.waw.pl> 6 * 7 * The code is based on publicly available information: 8 * - Intel IXP4xx Developer's Manual and other e-papers 9 * - Intel IXP400 Access Library Software (BSD license) 10 * - previous works by Christian Hohnstaedt <chohnstaedt@innominate.com> 11 * Thanks, Christian. 12 */ 13 14 #include <linux/delay.h> 15 #include <linux/dma-mapping.h> 16 #include <linux/firmware.h> 17 #include <linux/io.h> 18 #include <linux/kernel.h> 19 #include <linux/module.h> 20 #include <linux/of.h> 21 #include <linux/platform_device.h> 22 #include <linux/soc/ixp4xx/npe.h> 23 #include <mach/hardware.h> 24 #include <linux/soc/ixp4xx/cpu.h> 25 26 #define DEBUG_MSG 0 27 #define DEBUG_FW 0 28 29 #define NPE_COUNT 3 30 #define MAX_RETRIES 1000 /* microseconds */ 31 #define NPE_42X_DATA_SIZE 0x800 /* in dwords */ 32 #define NPE_46X_DATA_SIZE 0x1000 33 #define NPE_A_42X_INSTR_SIZE 0x1000 34 #define NPE_B_AND_C_42X_INSTR_SIZE 0x800 35 #define NPE_46X_INSTR_SIZE 0x1000 36 #define REGS_SIZE 0x1000 37 38 #define NPE_PHYS_REG 32 39 40 #define FW_MAGIC 0xFEEDF00D 41 #define FW_BLOCK_TYPE_INSTR 0x0 42 #define FW_BLOCK_TYPE_DATA 0x1 43 #define FW_BLOCK_TYPE_EOF 0xF 44 45 /* NPE exec status (read) and command (write) */ 46 #define CMD_NPE_STEP 0x01 47 #define CMD_NPE_START 0x02 48 #define CMD_NPE_STOP 0x03 49 #define CMD_NPE_CLR_PIPE 0x04 50 #define CMD_CLR_PROFILE_CNT 0x0C 51 #define CMD_RD_INS_MEM 0x10 /* instruction memory */ 52 #define CMD_WR_INS_MEM 0x11 53 #define CMD_RD_DATA_MEM 0x12 /* data memory */ 54 #define CMD_WR_DATA_MEM 0x13 55 #define CMD_RD_ECS_REG 0x14 /* exec access register */ 56 #define CMD_WR_ECS_REG 0x15 57 58 #define STAT_RUN 0x80000000 59 #define STAT_STOP 0x40000000 60 #define STAT_CLEAR 0x20000000 61 #define STAT_ECS_K 0x00800000 /* pipeline clean */ 62 63 #define NPE_STEVT 0x1B 64 #define NPE_STARTPC 0x1C 65 #define NPE_REGMAP 0x1E 66 #define NPE_CINDEX 0x1F 67 68 #define INSTR_WR_REG_SHORT 0x0000C000 69 #define INSTR_WR_REG_BYTE 0x00004000 70 #define INSTR_RD_FIFO 0x0F888220 71 #define INSTR_RESET_MBOX 0x0FAC8210 72 73 #define ECS_BG_CTXT_REG_0 0x00 /* Background Executing Context */ 74 #define ECS_BG_CTXT_REG_1 0x01 /* Stack level */ 75 #define ECS_BG_CTXT_REG_2 0x02 76 #define ECS_PRI_1_CTXT_REG_0 0x04 /* Priority 1 Executing Context */ 77 #define ECS_PRI_1_CTXT_REG_1 0x05 /* Stack level */ 78 #define ECS_PRI_1_CTXT_REG_2 0x06 79 #define ECS_PRI_2_CTXT_REG_0 0x08 /* Priority 2 Executing Context */ 80 #define ECS_PRI_2_CTXT_REG_1 0x09 /* Stack level */ 81 #define ECS_PRI_2_CTXT_REG_2 0x0A 82 #define ECS_DBG_CTXT_REG_0 0x0C /* Debug Executing Context */ 83 #define ECS_DBG_CTXT_REG_1 0x0D /* Stack level */ 84 #define ECS_DBG_CTXT_REG_2 0x0E 85 #define ECS_INSTRUCT_REG 0x11 /* NPE Instruction Register */ 86 87 #define ECS_REG_0_ACTIVE 0x80000000 /* all levels */ 88 #define ECS_REG_0_NEXTPC_MASK 0x1FFF0000 /* BG/PRI1/PRI2 levels */ 89 #define ECS_REG_0_LDUR_BITS 8 90 #define ECS_REG_0_LDUR_MASK 0x00000700 /* all levels */ 91 #define ECS_REG_1_CCTXT_BITS 16 92 #define ECS_REG_1_CCTXT_MASK 0x000F0000 /* all levels */ 93 #define ECS_REG_1_SELCTXT_BITS 0 94 #define ECS_REG_1_SELCTXT_MASK 0x0000000F /* all levels */ 95 #define ECS_DBG_REG_2_IF 0x00100000 /* debug level */ 96 #define ECS_DBG_REG_2_IE 0x00080000 /* debug level */ 97 98 /* NPE watchpoint_fifo register bit */ 99 #define WFIFO_VALID 0x80000000 100 101 /* NPE messaging_status register bit definitions */ 102 #define MSGSTAT_OFNE 0x00010000 /* OutFifoNotEmpty */ 103 #define MSGSTAT_IFNF 0x00020000 /* InFifoNotFull */ 104 #define MSGSTAT_OFNF 0x00040000 /* OutFifoNotFull */ 105 #define MSGSTAT_IFNE 0x00080000 /* InFifoNotEmpty */ 106 #define MSGSTAT_MBINT 0x00100000 /* Mailbox interrupt */ 107 #define MSGSTAT_IFINT 0x00200000 /* InFifo interrupt */ 108 #define MSGSTAT_OFINT 0x00400000 /* OutFifo interrupt */ 109 #define MSGSTAT_WFINT 0x00800000 /* WatchFifo interrupt */ 110 111 /* NPE messaging_control register bit definitions */ 112 #define MSGCTL_OUT_FIFO 0x00010000 /* enable output FIFO */ 113 #define MSGCTL_IN_FIFO 0x00020000 /* enable input FIFO */ 114 #define MSGCTL_OUT_FIFO_WRITE 0x01000000 /* enable FIFO + WRITE */ 115 #define MSGCTL_IN_FIFO_WRITE 0x02000000 116 117 /* NPE mailbox_status value for reset */ 118 #define RESET_MBOX_STAT 0x0000F0F0 119 120 #define NPE_A_FIRMWARE "NPE-A" 121 #define NPE_B_FIRMWARE "NPE-B" 122 #define NPE_C_FIRMWARE "NPE-C" 123 124 const char *npe_names[] = { NPE_A_FIRMWARE, NPE_B_FIRMWARE, NPE_C_FIRMWARE }; 125 126 #define print_npe(pri, npe, fmt, ...) \ 127 printk(pri "%s: " fmt, npe_name(npe), ## __VA_ARGS__) 128 129 #if DEBUG_MSG 130 #define debug_msg(npe, fmt, ...) \ 131 print_npe(KERN_DEBUG, npe, fmt, ## __VA_ARGS__) 132 #else 133 #define debug_msg(npe, fmt, ...) 134 #endif 135 136 static struct { 137 u32 reg, val; 138 } ecs_reset[] = { 139 { ECS_BG_CTXT_REG_0, 0xA0000000 }, 140 { ECS_BG_CTXT_REG_1, 0x01000000 }, 141 { ECS_BG_CTXT_REG_2, 0x00008000 }, 142 { ECS_PRI_1_CTXT_REG_0, 0x20000080 }, 143 { ECS_PRI_1_CTXT_REG_1, 0x01000000 }, 144 { ECS_PRI_1_CTXT_REG_2, 0x00008000 }, 145 { ECS_PRI_2_CTXT_REG_0, 0x20000080 }, 146 { ECS_PRI_2_CTXT_REG_1, 0x01000000 }, 147 { ECS_PRI_2_CTXT_REG_2, 0x00008000 }, 148 { ECS_DBG_CTXT_REG_0, 0x20000000 }, 149 { ECS_DBG_CTXT_REG_1, 0x00000000 }, 150 { ECS_DBG_CTXT_REG_2, 0x001E0000 }, 151 { ECS_INSTRUCT_REG, 0x1003C00F }, 152 }; 153 154 static struct npe npe_tab[NPE_COUNT] = { 155 { 156 .id = 0, 157 }, { 158 .id = 1, 159 }, { 160 .id = 2, 161 } 162 }; 163 164 int npe_running(struct npe *npe) 165 { 166 return (__raw_readl(&npe->regs->exec_status_cmd) & STAT_RUN) != 0; 167 } 168 169 static void npe_cmd_write(struct npe *npe, u32 addr, int cmd, u32 data) 170 { 171 __raw_writel(data, &npe->regs->exec_data); 172 __raw_writel(addr, &npe->regs->exec_addr); 173 __raw_writel(cmd, &npe->regs->exec_status_cmd); 174 } 175 176 static u32 npe_cmd_read(struct npe *npe, u32 addr, int cmd) 177 { 178 __raw_writel(addr, &npe->regs->exec_addr); 179 __raw_writel(cmd, &npe->regs->exec_status_cmd); 180 /* Iintroduce extra read cycles after issuing read command to NPE 181 so that we read the register after the NPE has updated it. 182 This is to overcome race condition between XScale and NPE */ 183 __raw_readl(&npe->regs->exec_data); 184 __raw_readl(&npe->regs->exec_data); 185 return __raw_readl(&npe->regs->exec_data); 186 } 187 188 static void npe_clear_active(struct npe *npe, u32 reg) 189 { 190 u32 val = npe_cmd_read(npe, reg, CMD_RD_ECS_REG); 191 npe_cmd_write(npe, reg, CMD_WR_ECS_REG, val & ~ECS_REG_0_ACTIVE); 192 } 193 194 static void npe_start(struct npe *npe) 195 { 196 /* ensure only Background Context Stack Level is active */ 197 npe_clear_active(npe, ECS_PRI_1_CTXT_REG_0); 198 npe_clear_active(npe, ECS_PRI_2_CTXT_REG_0); 199 npe_clear_active(npe, ECS_DBG_CTXT_REG_0); 200 201 __raw_writel(CMD_NPE_CLR_PIPE, &npe->regs->exec_status_cmd); 202 __raw_writel(CMD_NPE_START, &npe->regs->exec_status_cmd); 203 } 204 205 static void npe_stop(struct npe *npe) 206 { 207 __raw_writel(CMD_NPE_STOP, &npe->regs->exec_status_cmd); 208 __raw_writel(CMD_NPE_CLR_PIPE, &npe->regs->exec_status_cmd); /*FIXME?*/ 209 } 210 211 static int __must_check npe_debug_instr(struct npe *npe, u32 instr, u32 ctx, 212 u32 ldur) 213 { 214 u32 wc; 215 int i; 216 217 /* set the Active bit, and the LDUR, in the debug level */ 218 npe_cmd_write(npe, ECS_DBG_CTXT_REG_0, CMD_WR_ECS_REG, 219 ECS_REG_0_ACTIVE | (ldur << ECS_REG_0_LDUR_BITS)); 220 221 /* set CCTXT at ECS DEBUG L3 to specify in which context to execute 222 the instruction, and set SELCTXT at ECS DEBUG Level to specify 223 which context store to access. 224 Debug ECS Level Reg 1 has form 0x000n000n, where n = context number 225 */ 226 npe_cmd_write(npe, ECS_DBG_CTXT_REG_1, CMD_WR_ECS_REG, 227 (ctx << ECS_REG_1_CCTXT_BITS) | 228 (ctx << ECS_REG_1_SELCTXT_BITS)); 229 230 /* clear the pipeline */ 231 __raw_writel(CMD_NPE_CLR_PIPE, &npe->regs->exec_status_cmd); 232 233 /* load NPE instruction into the instruction register */ 234 npe_cmd_write(npe, ECS_INSTRUCT_REG, CMD_WR_ECS_REG, instr); 235 236 /* we need this value later to wait for completion of NPE execution 237 step */ 238 wc = __raw_readl(&npe->regs->watch_count); 239 240 /* issue a Step One command via the Execution Control register */ 241 __raw_writel(CMD_NPE_STEP, &npe->regs->exec_status_cmd); 242 243 /* Watch Count register increments when NPE completes an instruction */ 244 for (i = 0; i < MAX_RETRIES; i++) { 245 if (wc != __raw_readl(&npe->regs->watch_count)) 246 return 0; 247 udelay(1); 248 } 249 250 print_npe(KERN_ERR, npe, "reset: npe_debug_instr(): timeout\n"); 251 return -ETIMEDOUT; 252 } 253 254 static int __must_check npe_logical_reg_write8(struct npe *npe, u32 addr, 255 u8 val, u32 ctx) 256 { 257 /* here we build the NPE assembler instruction: mov8 d0, #0 */ 258 u32 instr = INSTR_WR_REG_BYTE | /* OpCode */ 259 addr << 9 | /* base Operand */ 260 (val & 0x1F) << 4 | /* lower 5 bits to immediate data */ 261 (val & ~0x1F) << (18 - 5);/* higher 3 bits to CoProc instr. */ 262 return npe_debug_instr(npe, instr, ctx, 1); /* execute it */ 263 } 264 265 static int __must_check npe_logical_reg_write16(struct npe *npe, u32 addr, 266 u16 val, u32 ctx) 267 { 268 /* here we build the NPE assembler instruction: mov16 d0, #0 */ 269 u32 instr = INSTR_WR_REG_SHORT | /* OpCode */ 270 addr << 9 | /* base Operand */ 271 (val & 0x1F) << 4 | /* lower 5 bits to immediate data */ 272 (val & ~0x1F) << (18 - 5);/* higher 11 bits to CoProc instr. */ 273 return npe_debug_instr(npe, instr, ctx, 1); /* execute it */ 274 } 275 276 static int __must_check npe_logical_reg_write32(struct npe *npe, u32 addr, 277 u32 val, u32 ctx) 278 { 279 /* write in 16 bit steps first the high and then the low value */ 280 if (npe_logical_reg_write16(npe, addr, val >> 16, ctx)) 281 return -ETIMEDOUT; 282 return npe_logical_reg_write16(npe, addr + 2, val & 0xFFFF, ctx); 283 } 284 285 static int npe_reset(struct npe *npe) 286 { 287 u32 val, ctl, exec_count, ctx_reg2; 288 int i; 289 290 ctl = (__raw_readl(&npe->regs->messaging_control) | 0x3F000000) & 291 0x3F3FFFFF; 292 293 /* disable parity interrupt */ 294 __raw_writel(ctl & 0x3F00FFFF, &npe->regs->messaging_control); 295 296 /* pre exec - debug instruction */ 297 /* turn off the halt bit by clearing Execution Count register. */ 298 exec_count = __raw_readl(&npe->regs->exec_count); 299 __raw_writel(0, &npe->regs->exec_count); 300 /* ensure that IF and IE are on (temporarily), so that we don't end up 301 stepping forever */ 302 ctx_reg2 = npe_cmd_read(npe, ECS_DBG_CTXT_REG_2, CMD_RD_ECS_REG); 303 npe_cmd_write(npe, ECS_DBG_CTXT_REG_2, CMD_WR_ECS_REG, ctx_reg2 | 304 ECS_DBG_REG_2_IF | ECS_DBG_REG_2_IE); 305 306 /* clear the FIFOs */ 307 while (__raw_readl(&npe->regs->watchpoint_fifo) & WFIFO_VALID) 308 ; 309 while (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_OFNE) 310 /* read from the outFIFO until empty */ 311 print_npe(KERN_DEBUG, npe, "npe_reset: read FIFO = 0x%X\n", 312 __raw_readl(&npe->regs->in_out_fifo)); 313 314 while (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_IFNE) 315 /* step execution of the NPE intruction to read inFIFO using 316 the Debug Executing Context stack */ 317 if (npe_debug_instr(npe, INSTR_RD_FIFO, 0, 0)) 318 return -ETIMEDOUT; 319 320 /* reset the mailbox reg from the XScale side */ 321 __raw_writel(RESET_MBOX_STAT, &npe->regs->mailbox_status); 322 /* from NPE side */ 323 if (npe_debug_instr(npe, INSTR_RESET_MBOX, 0, 0)) 324 return -ETIMEDOUT; 325 326 /* Reset the physical registers in the NPE register file */ 327 for (val = 0; val < NPE_PHYS_REG; val++) { 328 if (npe_logical_reg_write16(npe, NPE_REGMAP, val >> 1, 0)) 329 return -ETIMEDOUT; 330 /* address is either 0 or 4 */ 331 if (npe_logical_reg_write32(npe, (val & 1) * 4, 0, 0)) 332 return -ETIMEDOUT; 333 } 334 335 /* Reset the context store = each context's Context Store registers */ 336 337 /* Context 0 has no STARTPC. Instead, this value is used to set NextPC 338 for Background ECS, to set where NPE starts executing code */ 339 val = npe_cmd_read(npe, ECS_BG_CTXT_REG_0, CMD_RD_ECS_REG); 340 val &= ~ECS_REG_0_NEXTPC_MASK; 341 val |= (0 /* NextPC */ << 16) & ECS_REG_0_NEXTPC_MASK; 342 npe_cmd_write(npe, ECS_BG_CTXT_REG_0, CMD_WR_ECS_REG, val); 343 344 for (i = 0; i < 16; i++) { 345 if (i) { /* Context 0 has no STEVT nor STARTPC */ 346 /* STEVT = off, 0x80 */ 347 if (npe_logical_reg_write8(npe, NPE_STEVT, 0x80, i)) 348 return -ETIMEDOUT; 349 if (npe_logical_reg_write16(npe, NPE_STARTPC, 0, i)) 350 return -ETIMEDOUT; 351 } 352 /* REGMAP = d0->p0, d8->p2, d16->p4 */ 353 if (npe_logical_reg_write16(npe, NPE_REGMAP, 0x820, i)) 354 return -ETIMEDOUT; 355 if (npe_logical_reg_write8(npe, NPE_CINDEX, 0, i)) 356 return -ETIMEDOUT; 357 } 358 359 /* post exec */ 360 /* clear active bit in debug level */ 361 npe_cmd_write(npe, ECS_DBG_CTXT_REG_0, CMD_WR_ECS_REG, 0); 362 /* clear the pipeline */ 363 __raw_writel(CMD_NPE_CLR_PIPE, &npe->regs->exec_status_cmd); 364 /* restore previous values */ 365 __raw_writel(exec_count, &npe->regs->exec_count); 366 npe_cmd_write(npe, ECS_DBG_CTXT_REG_2, CMD_WR_ECS_REG, ctx_reg2); 367 368 /* write reset values to Execution Context Stack registers */ 369 for (val = 0; val < ARRAY_SIZE(ecs_reset); val++) 370 npe_cmd_write(npe, ecs_reset[val].reg, CMD_WR_ECS_REG, 371 ecs_reset[val].val); 372 373 /* clear the profile counter */ 374 __raw_writel(CMD_CLR_PROFILE_CNT, &npe->regs->exec_status_cmd); 375 376 __raw_writel(0, &npe->regs->exec_count); 377 __raw_writel(0, &npe->regs->action_points[0]); 378 __raw_writel(0, &npe->regs->action_points[1]); 379 __raw_writel(0, &npe->regs->action_points[2]); 380 __raw_writel(0, &npe->regs->action_points[3]); 381 __raw_writel(0, &npe->regs->watch_count); 382 383 val = ixp4xx_read_feature_bits(); 384 /* reset the NPE */ 385 ixp4xx_write_feature_bits(val & 386 ~(IXP4XX_FEATURE_RESET_NPEA << npe->id)); 387 /* deassert reset */ 388 ixp4xx_write_feature_bits(val | 389 (IXP4XX_FEATURE_RESET_NPEA << npe->id)); 390 for (i = 0; i < MAX_RETRIES; i++) { 391 if (ixp4xx_read_feature_bits() & 392 (IXP4XX_FEATURE_RESET_NPEA << npe->id)) 393 break; /* NPE is back alive */ 394 udelay(1); 395 } 396 if (i == MAX_RETRIES) 397 return -ETIMEDOUT; 398 399 npe_stop(npe); 400 401 /* restore NPE configuration bus Control Register - parity settings */ 402 __raw_writel(ctl, &npe->regs->messaging_control); 403 return 0; 404 } 405 406 407 int npe_send_message(struct npe *npe, const void *msg, const char *what) 408 { 409 const u32 *send = msg; 410 int cycles = 0; 411 412 debug_msg(npe, "Trying to send message %s [%08X:%08X]\n", 413 what, send[0], send[1]); 414 415 if (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_IFNE) { 416 debug_msg(npe, "NPE input FIFO not empty\n"); 417 return -EIO; 418 } 419 420 __raw_writel(send[0], &npe->regs->in_out_fifo); 421 422 if (!(__raw_readl(&npe->regs->messaging_status) & MSGSTAT_IFNF)) { 423 debug_msg(npe, "NPE input FIFO full\n"); 424 return -EIO; 425 } 426 427 __raw_writel(send[1], &npe->regs->in_out_fifo); 428 429 while ((cycles < MAX_RETRIES) && 430 (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_IFNE)) { 431 udelay(1); 432 cycles++; 433 } 434 435 if (cycles == MAX_RETRIES) { 436 debug_msg(npe, "Timeout sending message\n"); 437 return -ETIMEDOUT; 438 } 439 440 #if DEBUG_MSG > 1 441 debug_msg(npe, "Sending a message took %i cycles\n", cycles); 442 #endif 443 return 0; 444 } 445 446 int npe_recv_message(struct npe *npe, void *msg, const char *what) 447 { 448 u32 *recv = msg; 449 int cycles = 0, cnt = 0; 450 451 debug_msg(npe, "Trying to receive message %s\n", what); 452 453 while (cycles < MAX_RETRIES) { 454 if (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_OFNE) { 455 recv[cnt++] = __raw_readl(&npe->regs->in_out_fifo); 456 if (cnt == 2) 457 break; 458 } else { 459 udelay(1); 460 cycles++; 461 } 462 } 463 464 switch(cnt) { 465 case 1: 466 debug_msg(npe, "Received [%08X]\n", recv[0]); 467 break; 468 case 2: 469 debug_msg(npe, "Received [%08X:%08X]\n", recv[0], recv[1]); 470 break; 471 } 472 473 if (cycles == MAX_RETRIES) { 474 debug_msg(npe, "Timeout waiting for message\n"); 475 return -ETIMEDOUT; 476 } 477 478 #if DEBUG_MSG > 1 479 debug_msg(npe, "Receiving a message took %i cycles\n", cycles); 480 #endif 481 return 0; 482 } 483 484 int npe_send_recv_message(struct npe *npe, void *msg, const char *what) 485 { 486 int result; 487 u32 *send = msg, recv[2]; 488 489 if ((result = npe_send_message(npe, msg, what)) != 0) 490 return result; 491 if ((result = npe_recv_message(npe, recv, what)) != 0) 492 return result; 493 494 if ((recv[0] != send[0]) || (recv[1] != send[1])) { 495 debug_msg(npe, "Message %s: unexpected message received\n", 496 what); 497 return -EIO; 498 } 499 return 0; 500 } 501 502 503 int npe_load_firmware(struct npe *npe, const char *name, struct device *dev) 504 { 505 const struct firmware *fw_entry; 506 507 struct dl_block { 508 u32 type; 509 u32 offset; 510 } *blk; 511 512 struct dl_image { 513 u32 magic; 514 u32 id; 515 u32 size; 516 union { 517 u32 data[0]; 518 struct dl_block blocks[0]; 519 }; 520 } *image; 521 522 struct dl_codeblock { 523 u32 npe_addr; 524 u32 size; 525 u32 data[0]; 526 } *cb; 527 528 int i, j, err, data_size, instr_size, blocks, table_end; 529 u32 cmd; 530 531 if ((err = request_firmware(&fw_entry, name, dev)) != 0) 532 return err; 533 534 err = -EINVAL; 535 if (fw_entry->size < sizeof(struct dl_image)) { 536 print_npe(KERN_ERR, npe, "incomplete firmware file\n"); 537 goto err; 538 } 539 image = (struct dl_image*)fw_entry->data; 540 541 #if DEBUG_FW 542 print_npe(KERN_DEBUG, npe, "firmware: %08X %08X %08X (0x%X bytes)\n", 543 image->magic, image->id, image->size, image->size * 4); 544 #endif 545 546 if (image->magic == swab32(FW_MAGIC)) { /* swapped file */ 547 image->id = swab32(image->id); 548 image->size = swab32(image->size); 549 } else if (image->magic != FW_MAGIC) { 550 print_npe(KERN_ERR, npe, "bad firmware file magic: 0x%X\n", 551 image->magic); 552 goto err; 553 } 554 if ((image->size * 4 + sizeof(struct dl_image)) != fw_entry->size) { 555 print_npe(KERN_ERR, npe, 556 "inconsistent size of firmware file\n"); 557 goto err; 558 } 559 if (((image->id >> 24) & 0xF /* NPE ID */) != npe->id) { 560 print_npe(KERN_ERR, npe, "firmware file NPE ID mismatch\n"); 561 goto err; 562 } 563 if (image->magic == swab32(FW_MAGIC)) 564 for (i = 0; i < image->size; i++) 565 image->data[i] = swab32(image->data[i]); 566 567 if (cpu_is_ixp42x() && ((image->id >> 28) & 0xF /* device ID */)) { 568 print_npe(KERN_INFO, npe, "IXP43x/IXP46x firmware ignored on " 569 "IXP42x\n"); 570 goto err; 571 } 572 573 if (npe_running(npe)) { 574 print_npe(KERN_INFO, npe, "unable to load firmware, NPE is " 575 "already running\n"); 576 err = -EBUSY; 577 goto err; 578 } 579 #if 0 580 npe_stop(npe); 581 npe_reset(npe); 582 #endif 583 584 print_npe(KERN_INFO, npe, "firmware functionality 0x%X, " 585 "revision 0x%X:%X\n", (image->id >> 16) & 0xFF, 586 (image->id >> 8) & 0xFF, image->id & 0xFF); 587 588 if (cpu_is_ixp42x()) { 589 if (!npe->id) 590 instr_size = NPE_A_42X_INSTR_SIZE; 591 else 592 instr_size = NPE_B_AND_C_42X_INSTR_SIZE; 593 data_size = NPE_42X_DATA_SIZE; 594 } else { 595 instr_size = NPE_46X_INSTR_SIZE; 596 data_size = NPE_46X_DATA_SIZE; 597 } 598 599 for (blocks = 0; blocks * sizeof(struct dl_block) / 4 < image->size; 600 blocks++) 601 if (image->blocks[blocks].type == FW_BLOCK_TYPE_EOF) 602 break; 603 if (blocks * sizeof(struct dl_block) / 4 >= image->size) { 604 print_npe(KERN_INFO, npe, "firmware EOF block marker not " 605 "found\n"); 606 goto err; 607 } 608 609 #if DEBUG_FW 610 print_npe(KERN_DEBUG, npe, "%i firmware blocks found\n", blocks); 611 #endif 612 613 table_end = blocks * sizeof(struct dl_block) / 4 + 1 /* EOF marker */; 614 for (i = 0, blk = image->blocks; i < blocks; i++, blk++) { 615 if (blk->offset > image->size - sizeof(struct dl_codeblock) / 4 616 || blk->offset < table_end) { 617 print_npe(KERN_INFO, npe, "invalid offset 0x%X of " 618 "firmware block #%i\n", blk->offset, i); 619 goto err; 620 } 621 622 cb = (struct dl_codeblock*)&image->data[blk->offset]; 623 if (blk->type == FW_BLOCK_TYPE_INSTR) { 624 if (cb->npe_addr + cb->size > instr_size) 625 goto too_big; 626 cmd = CMD_WR_INS_MEM; 627 } else if (blk->type == FW_BLOCK_TYPE_DATA) { 628 if (cb->npe_addr + cb->size > data_size) 629 goto too_big; 630 cmd = CMD_WR_DATA_MEM; 631 } else { 632 print_npe(KERN_INFO, npe, "invalid firmware block #%i " 633 "type 0x%X\n", i, blk->type); 634 goto err; 635 } 636 if (blk->offset + sizeof(*cb) / 4 + cb->size > image->size) { 637 print_npe(KERN_INFO, npe, "firmware block #%i doesn't " 638 "fit in firmware image: type %c, start 0x%X," 639 " length 0x%X\n", i, 640 blk->type == FW_BLOCK_TYPE_INSTR ? 'I' : 'D', 641 cb->npe_addr, cb->size); 642 goto err; 643 } 644 645 for (j = 0; j < cb->size; j++) 646 npe_cmd_write(npe, cb->npe_addr + j, cmd, cb->data[j]); 647 } 648 649 npe_start(npe); 650 if (!npe_running(npe)) 651 print_npe(KERN_ERR, npe, "unable to start\n"); 652 release_firmware(fw_entry); 653 return 0; 654 655 too_big: 656 print_npe(KERN_INFO, npe, "firmware block #%i doesn't fit in NPE " 657 "memory: type %c, start 0x%X, length 0x%X\n", i, 658 blk->type == FW_BLOCK_TYPE_INSTR ? 'I' : 'D', 659 cb->npe_addr, cb->size); 660 err: 661 release_firmware(fw_entry); 662 return err; 663 } 664 665 666 struct npe *npe_request(unsigned id) 667 { 668 if (id < NPE_COUNT) 669 if (npe_tab[id].valid) 670 if (try_module_get(THIS_MODULE)) 671 return &npe_tab[id]; 672 return NULL; 673 } 674 675 void npe_release(struct npe *npe) 676 { 677 module_put(THIS_MODULE); 678 } 679 680 static int ixp4xx_npe_probe(struct platform_device *pdev) 681 { 682 int i, found = 0; 683 struct device *dev = &pdev->dev; 684 struct resource *res; 685 686 for (i = 0; i < NPE_COUNT; i++) { 687 struct npe *npe = &npe_tab[i]; 688 689 res = platform_get_resource(pdev, IORESOURCE_MEM, i); 690 if (!res) 691 return -ENODEV; 692 693 if (!(ixp4xx_read_feature_bits() & 694 (IXP4XX_FEATURE_RESET_NPEA << i))) { 695 dev_info(dev, "NPE%d at 0x%08x-0x%08x not available\n", 696 i, res->start, res->end); 697 continue; /* NPE already disabled or not present */ 698 } 699 npe->regs = devm_ioremap_resource(dev, res); 700 if (IS_ERR(npe->regs)) 701 return PTR_ERR(npe->regs); 702 703 if (npe_reset(npe)) { 704 dev_info(dev, "NPE%d at 0x%08x-0x%08x does not reset\n", 705 i, res->start, res->end); 706 continue; 707 } 708 npe->valid = 1; 709 dev_info(dev, "NPE%d at 0x%08x-0x%08x registered\n", 710 i, res->start, res->end); 711 found++; 712 } 713 714 if (!found) 715 return -ENODEV; 716 return 0; 717 } 718 719 static int ixp4xx_npe_remove(struct platform_device *pdev) 720 { 721 int i; 722 723 for (i = 0; i < NPE_COUNT; i++) 724 if (npe_tab[i].regs) { 725 npe_reset(&npe_tab[i]); 726 } 727 728 return 0; 729 } 730 731 static const struct of_device_id ixp4xx_npe_of_match[] = { 732 { 733 .compatible = "intel,ixp4xx-network-processing-engine", 734 }, 735 {}, 736 }; 737 738 static struct platform_driver ixp4xx_npe_driver = { 739 .driver = { 740 .name = "ixp4xx-npe", 741 .of_match_table = of_match_ptr(ixp4xx_npe_of_match), 742 }, 743 .probe = ixp4xx_npe_probe, 744 .remove = ixp4xx_npe_remove, 745 }; 746 module_platform_driver(ixp4xx_npe_driver); 747 748 MODULE_AUTHOR("Krzysztof Halasa"); 749 MODULE_LICENSE("GPL v2"); 750 MODULE_FIRMWARE(NPE_A_FIRMWARE); 751 MODULE_FIRMWARE(NPE_B_FIRMWARE); 752 MODULE_FIRMWARE(NPE_C_FIRMWARE); 753 754 EXPORT_SYMBOL(npe_names); 755 EXPORT_SYMBOL(npe_running); 756 EXPORT_SYMBOL(npe_request); 757 EXPORT_SYMBOL(npe_release); 758 EXPORT_SYMBOL(npe_load_firmware); 759 EXPORT_SYMBOL(npe_send_message); 760 EXPORT_SYMBOL(npe_recv_message); 761 EXPORT_SYMBOL(npe_send_recv_message); 762