1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Intel IXP4xx Network Processor Engine driver for Linux 4 * 5 * Copyright (C) 2007 Krzysztof Halasa <khc@pm.waw.pl> 6 * 7 * The code is based on publicly available information: 8 * - Intel IXP4xx Developer's Manual and other e-papers 9 * - Intel IXP400 Access Library Software (BSD license) 10 * - previous works by Christian Hohnstaedt <chohnstaedt@innominate.com> 11 * Thanks, Christian. 12 */ 13 14 #include <linux/delay.h> 15 #include <linux/dma-mapping.h> 16 #include <linux/firmware.h> 17 #include <linux/io.h> 18 #include <linux/kernel.h> 19 #include <linux/module.h> 20 #include <linux/of.h> 21 #include <linux/of_platform.h> 22 #include <linux/platform_device.h> 23 #include <linux/soc/ixp4xx/npe.h> 24 #include <mach/hardware.h> 25 #include <linux/soc/ixp4xx/cpu.h> 26 27 #define DEBUG_MSG 0 28 #define DEBUG_FW 0 29 30 #define NPE_COUNT 3 31 #define MAX_RETRIES 1000 /* microseconds */ 32 #define NPE_42X_DATA_SIZE 0x800 /* in dwords */ 33 #define NPE_46X_DATA_SIZE 0x1000 34 #define NPE_A_42X_INSTR_SIZE 0x1000 35 #define NPE_B_AND_C_42X_INSTR_SIZE 0x800 36 #define NPE_46X_INSTR_SIZE 0x1000 37 #define REGS_SIZE 0x1000 38 39 #define NPE_PHYS_REG 32 40 41 #define FW_MAGIC 0xFEEDF00D 42 #define FW_BLOCK_TYPE_INSTR 0x0 43 #define FW_BLOCK_TYPE_DATA 0x1 44 #define FW_BLOCK_TYPE_EOF 0xF 45 46 /* NPE exec status (read) and command (write) */ 47 #define CMD_NPE_STEP 0x01 48 #define CMD_NPE_START 0x02 49 #define CMD_NPE_STOP 0x03 50 #define CMD_NPE_CLR_PIPE 0x04 51 #define CMD_CLR_PROFILE_CNT 0x0C 52 #define CMD_RD_INS_MEM 0x10 /* instruction memory */ 53 #define CMD_WR_INS_MEM 0x11 54 #define CMD_RD_DATA_MEM 0x12 /* data memory */ 55 #define CMD_WR_DATA_MEM 0x13 56 #define CMD_RD_ECS_REG 0x14 /* exec access register */ 57 #define CMD_WR_ECS_REG 0x15 58 59 #define STAT_RUN 0x80000000 60 #define STAT_STOP 0x40000000 61 #define STAT_CLEAR 0x20000000 62 #define STAT_ECS_K 0x00800000 /* pipeline clean */ 63 64 #define NPE_STEVT 0x1B 65 #define NPE_STARTPC 0x1C 66 #define NPE_REGMAP 0x1E 67 #define NPE_CINDEX 0x1F 68 69 #define INSTR_WR_REG_SHORT 0x0000C000 70 #define INSTR_WR_REG_BYTE 0x00004000 71 #define INSTR_RD_FIFO 0x0F888220 72 #define INSTR_RESET_MBOX 0x0FAC8210 73 74 #define ECS_BG_CTXT_REG_0 0x00 /* Background Executing Context */ 75 #define ECS_BG_CTXT_REG_1 0x01 /* Stack level */ 76 #define ECS_BG_CTXT_REG_2 0x02 77 #define ECS_PRI_1_CTXT_REG_0 0x04 /* Priority 1 Executing Context */ 78 #define ECS_PRI_1_CTXT_REG_1 0x05 /* Stack level */ 79 #define ECS_PRI_1_CTXT_REG_2 0x06 80 #define ECS_PRI_2_CTXT_REG_0 0x08 /* Priority 2 Executing Context */ 81 #define ECS_PRI_2_CTXT_REG_1 0x09 /* Stack level */ 82 #define ECS_PRI_2_CTXT_REG_2 0x0A 83 #define ECS_DBG_CTXT_REG_0 0x0C /* Debug Executing Context */ 84 #define ECS_DBG_CTXT_REG_1 0x0D /* Stack level */ 85 #define ECS_DBG_CTXT_REG_2 0x0E 86 #define ECS_INSTRUCT_REG 0x11 /* NPE Instruction Register */ 87 88 #define ECS_REG_0_ACTIVE 0x80000000 /* all levels */ 89 #define ECS_REG_0_NEXTPC_MASK 0x1FFF0000 /* BG/PRI1/PRI2 levels */ 90 #define ECS_REG_0_LDUR_BITS 8 91 #define ECS_REG_0_LDUR_MASK 0x00000700 /* all levels */ 92 #define ECS_REG_1_CCTXT_BITS 16 93 #define ECS_REG_1_CCTXT_MASK 0x000F0000 /* all levels */ 94 #define ECS_REG_1_SELCTXT_BITS 0 95 #define ECS_REG_1_SELCTXT_MASK 0x0000000F /* all levels */ 96 #define ECS_DBG_REG_2_IF 0x00100000 /* debug level */ 97 #define ECS_DBG_REG_2_IE 0x00080000 /* debug level */ 98 99 /* NPE watchpoint_fifo register bit */ 100 #define WFIFO_VALID 0x80000000 101 102 /* NPE messaging_status register bit definitions */ 103 #define MSGSTAT_OFNE 0x00010000 /* OutFifoNotEmpty */ 104 #define MSGSTAT_IFNF 0x00020000 /* InFifoNotFull */ 105 #define MSGSTAT_OFNF 0x00040000 /* OutFifoNotFull */ 106 #define MSGSTAT_IFNE 0x00080000 /* InFifoNotEmpty */ 107 #define MSGSTAT_MBINT 0x00100000 /* Mailbox interrupt */ 108 #define MSGSTAT_IFINT 0x00200000 /* InFifo interrupt */ 109 #define MSGSTAT_OFINT 0x00400000 /* OutFifo interrupt */ 110 #define MSGSTAT_WFINT 0x00800000 /* WatchFifo interrupt */ 111 112 /* NPE messaging_control register bit definitions */ 113 #define MSGCTL_OUT_FIFO 0x00010000 /* enable output FIFO */ 114 #define MSGCTL_IN_FIFO 0x00020000 /* enable input FIFO */ 115 #define MSGCTL_OUT_FIFO_WRITE 0x01000000 /* enable FIFO + WRITE */ 116 #define MSGCTL_IN_FIFO_WRITE 0x02000000 117 118 /* NPE mailbox_status value for reset */ 119 #define RESET_MBOX_STAT 0x0000F0F0 120 121 #define NPE_A_FIRMWARE "NPE-A" 122 #define NPE_B_FIRMWARE "NPE-B" 123 #define NPE_C_FIRMWARE "NPE-C" 124 125 const char *npe_names[] = { NPE_A_FIRMWARE, NPE_B_FIRMWARE, NPE_C_FIRMWARE }; 126 127 #define print_npe(pri, npe, fmt, ...) \ 128 printk(pri "%s: " fmt, npe_name(npe), ## __VA_ARGS__) 129 130 #if DEBUG_MSG 131 #define debug_msg(npe, fmt, ...) \ 132 print_npe(KERN_DEBUG, npe, fmt, ## __VA_ARGS__) 133 #else 134 #define debug_msg(npe, fmt, ...) 135 #endif 136 137 static struct { 138 u32 reg, val; 139 } ecs_reset[] = { 140 { ECS_BG_CTXT_REG_0, 0xA0000000 }, 141 { ECS_BG_CTXT_REG_1, 0x01000000 }, 142 { ECS_BG_CTXT_REG_2, 0x00008000 }, 143 { ECS_PRI_1_CTXT_REG_0, 0x20000080 }, 144 { ECS_PRI_1_CTXT_REG_1, 0x01000000 }, 145 { ECS_PRI_1_CTXT_REG_2, 0x00008000 }, 146 { ECS_PRI_2_CTXT_REG_0, 0x20000080 }, 147 { ECS_PRI_2_CTXT_REG_1, 0x01000000 }, 148 { ECS_PRI_2_CTXT_REG_2, 0x00008000 }, 149 { ECS_DBG_CTXT_REG_0, 0x20000000 }, 150 { ECS_DBG_CTXT_REG_1, 0x00000000 }, 151 { ECS_DBG_CTXT_REG_2, 0x001E0000 }, 152 { ECS_INSTRUCT_REG, 0x1003C00F }, 153 }; 154 155 static struct npe npe_tab[NPE_COUNT] = { 156 { 157 .id = 0, 158 }, { 159 .id = 1, 160 }, { 161 .id = 2, 162 } 163 }; 164 165 int npe_running(struct npe *npe) 166 { 167 return (__raw_readl(&npe->regs->exec_status_cmd) & STAT_RUN) != 0; 168 } 169 170 static void npe_cmd_write(struct npe *npe, u32 addr, int cmd, u32 data) 171 { 172 __raw_writel(data, &npe->regs->exec_data); 173 __raw_writel(addr, &npe->regs->exec_addr); 174 __raw_writel(cmd, &npe->regs->exec_status_cmd); 175 } 176 177 static u32 npe_cmd_read(struct npe *npe, u32 addr, int cmd) 178 { 179 __raw_writel(addr, &npe->regs->exec_addr); 180 __raw_writel(cmd, &npe->regs->exec_status_cmd); 181 /* Iintroduce extra read cycles after issuing read command to NPE 182 so that we read the register after the NPE has updated it. 183 This is to overcome race condition between XScale and NPE */ 184 __raw_readl(&npe->regs->exec_data); 185 __raw_readl(&npe->regs->exec_data); 186 return __raw_readl(&npe->regs->exec_data); 187 } 188 189 static void npe_clear_active(struct npe *npe, u32 reg) 190 { 191 u32 val = npe_cmd_read(npe, reg, CMD_RD_ECS_REG); 192 npe_cmd_write(npe, reg, CMD_WR_ECS_REG, val & ~ECS_REG_0_ACTIVE); 193 } 194 195 static void npe_start(struct npe *npe) 196 { 197 /* ensure only Background Context Stack Level is active */ 198 npe_clear_active(npe, ECS_PRI_1_CTXT_REG_0); 199 npe_clear_active(npe, ECS_PRI_2_CTXT_REG_0); 200 npe_clear_active(npe, ECS_DBG_CTXT_REG_0); 201 202 __raw_writel(CMD_NPE_CLR_PIPE, &npe->regs->exec_status_cmd); 203 __raw_writel(CMD_NPE_START, &npe->regs->exec_status_cmd); 204 } 205 206 static void npe_stop(struct npe *npe) 207 { 208 __raw_writel(CMD_NPE_STOP, &npe->regs->exec_status_cmd); 209 __raw_writel(CMD_NPE_CLR_PIPE, &npe->regs->exec_status_cmd); /*FIXME?*/ 210 } 211 212 static int __must_check npe_debug_instr(struct npe *npe, u32 instr, u32 ctx, 213 u32 ldur) 214 { 215 u32 wc; 216 int i; 217 218 /* set the Active bit, and the LDUR, in the debug level */ 219 npe_cmd_write(npe, ECS_DBG_CTXT_REG_0, CMD_WR_ECS_REG, 220 ECS_REG_0_ACTIVE | (ldur << ECS_REG_0_LDUR_BITS)); 221 222 /* set CCTXT at ECS DEBUG L3 to specify in which context to execute 223 the instruction, and set SELCTXT at ECS DEBUG Level to specify 224 which context store to access. 225 Debug ECS Level Reg 1 has form 0x000n000n, where n = context number 226 */ 227 npe_cmd_write(npe, ECS_DBG_CTXT_REG_1, CMD_WR_ECS_REG, 228 (ctx << ECS_REG_1_CCTXT_BITS) | 229 (ctx << ECS_REG_1_SELCTXT_BITS)); 230 231 /* clear the pipeline */ 232 __raw_writel(CMD_NPE_CLR_PIPE, &npe->regs->exec_status_cmd); 233 234 /* load NPE instruction into the instruction register */ 235 npe_cmd_write(npe, ECS_INSTRUCT_REG, CMD_WR_ECS_REG, instr); 236 237 /* we need this value later to wait for completion of NPE execution 238 step */ 239 wc = __raw_readl(&npe->regs->watch_count); 240 241 /* issue a Step One command via the Execution Control register */ 242 __raw_writel(CMD_NPE_STEP, &npe->regs->exec_status_cmd); 243 244 /* Watch Count register increments when NPE completes an instruction */ 245 for (i = 0; i < MAX_RETRIES; i++) { 246 if (wc != __raw_readl(&npe->regs->watch_count)) 247 return 0; 248 udelay(1); 249 } 250 251 print_npe(KERN_ERR, npe, "reset: npe_debug_instr(): timeout\n"); 252 return -ETIMEDOUT; 253 } 254 255 static int __must_check npe_logical_reg_write8(struct npe *npe, u32 addr, 256 u8 val, u32 ctx) 257 { 258 /* here we build the NPE assembler instruction: mov8 d0, #0 */ 259 u32 instr = INSTR_WR_REG_BYTE | /* OpCode */ 260 addr << 9 | /* base Operand */ 261 (val & 0x1F) << 4 | /* lower 5 bits to immediate data */ 262 (val & ~0x1F) << (18 - 5);/* higher 3 bits to CoProc instr. */ 263 return npe_debug_instr(npe, instr, ctx, 1); /* execute it */ 264 } 265 266 static int __must_check npe_logical_reg_write16(struct npe *npe, u32 addr, 267 u16 val, u32 ctx) 268 { 269 /* here we build the NPE assembler instruction: mov16 d0, #0 */ 270 u32 instr = INSTR_WR_REG_SHORT | /* OpCode */ 271 addr << 9 | /* base Operand */ 272 (val & 0x1F) << 4 | /* lower 5 bits to immediate data */ 273 (val & ~0x1F) << (18 - 5);/* higher 11 bits to CoProc instr. */ 274 return npe_debug_instr(npe, instr, ctx, 1); /* execute it */ 275 } 276 277 static int __must_check npe_logical_reg_write32(struct npe *npe, u32 addr, 278 u32 val, u32 ctx) 279 { 280 /* write in 16 bit steps first the high and then the low value */ 281 if (npe_logical_reg_write16(npe, addr, val >> 16, ctx)) 282 return -ETIMEDOUT; 283 return npe_logical_reg_write16(npe, addr + 2, val & 0xFFFF, ctx); 284 } 285 286 static int npe_reset(struct npe *npe) 287 { 288 u32 val, ctl, exec_count, ctx_reg2; 289 int i; 290 291 ctl = (__raw_readl(&npe->regs->messaging_control) | 0x3F000000) & 292 0x3F3FFFFF; 293 294 /* disable parity interrupt */ 295 __raw_writel(ctl & 0x3F00FFFF, &npe->regs->messaging_control); 296 297 /* pre exec - debug instruction */ 298 /* turn off the halt bit by clearing Execution Count register. */ 299 exec_count = __raw_readl(&npe->regs->exec_count); 300 __raw_writel(0, &npe->regs->exec_count); 301 /* ensure that IF and IE are on (temporarily), so that we don't end up 302 stepping forever */ 303 ctx_reg2 = npe_cmd_read(npe, ECS_DBG_CTXT_REG_2, CMD_RD_ECS_REG); 304 npe_cmd_write(npe, ECS_DBG_CTXT_REG_2, CMD_WR_ECS_REG, ctx_reg2 | 305 ECS_DBG_REG_2_IF | ECS_DBG_REG_2_IE); 306 307 /* clear the FIFOs */ 308 while (__raw_readl(&npe->regs->watchpoint_fifo) & WFIFO_VALID) 309 ; 310 while (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_OFNE) 311 /* read from the outFIFO until empty */ 312 print_npe(KERN_DEBUG, npe, "npe_reset: read FIFO = 0x%X\n", 313 __raw_readl(&npe->regs->in_out_fifo)); 314 315 while (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_IFNE) 316 /* step execution of the NPE intruction to read inFIFO using 317 the Debug Executing Context stack */ 318 if (npe_debug_instr(npe, INSTR_RD_FIFO, 0, 0)) 319 return -ETIMEDOUT; 320 321 /* reset the mailbox reg from the XScale side */ 322 __raw_writel(RESET_MBOX_STAT, &npe->regs->mailbox_status); 323 /* from NPE side */ 324 if (npe_debug_instr(npe, INSTR_RESET_MBOX, 0, 0)) 325 return -ETIMEDOUT; 326 327 /* Reset the physical registers in the NPE register file */ 328 for (val = 0; val < NPE_PHYS_REG; val++) { 329 if (npe_logical_reg_write16(npe, NPE_REGMAP, val >> 1, 0)) 330 return -ETIMEDOUT; 331 /* address is either 0 or 4 */ 332 if (npe_logical_reg_write32(npe, (val & 1) * 4, 0, 0)) 333 return -ETIMEDOUT; 334 } 335 336 /* Reset the context store = each context's Context Store registers */ 337 338 /* Context 0 has no STARTPC. Instead, this value is used to set NextPC 339 for Background ECS, to set where NPE starts executing code */ 340 val = npe_cmd_read(npe, ECS_BG_CTXT_REG_0, CMD_RD_ECS_REG); 341 val &= ~ECS_REG_0_NEXTPC_MASK; 342 val |= (0 /* NextPC */ << 16) & ECS_REG_0_NEXTPC_MASK; 343 npe_cmd_write(npe, ECS_BG_CTXT_REG_0, CMD_WR_ECS_REG, val); 344 345 for (i = 0; i < 16; i++) { 346 if (i) { /* Context 0 has no STEVT nor STARTPC */ 347 /* STEVT = off, 0x80 */ 348 if (npe_logical_reg_write8(npe, NPE_STEVT, 0x80, i)) 349 return -ETIMEDOUT; 350 if (npe_logical_reg_write16(npe, NPE_STARTPC, 0, i)) 351 return -ETIMEDOUT; 352 } 353 /* REGMAP = d0->p0, d8->p2, d16->p4 */ 354 if (npe_logical_reg_write16(npe, NPE_REGMAP, 0x820, i)) 355 return -ETIMEDOUT; 356 if (npe_logical_reg_write8(npe, NPE_CINDEX, 0, i)) 357 return -ETIMEDOUT; 358 } 359 360 /* post exec */ 361 /* clear active bit in debug level */ 362 npe_cmd_write(npe, ECS_DBG_CTXT_REG_0, CMD_WR_ECS_REG, 0); 363 /* clear the pipeline */ 364 __raw_writel(CMD_NPE_CLR_PIPE, &npe->regs->exec_status_cmd); 365 /* restore previous values */ 366 __raw_writel(exec_count, &npe->regs->exec_count); 367 npe_cmd_write(npe, ECS_DBG_CTXT_REG_2, CMD_WR_ECS_REG, ctx_reg2); 368 369 /* write reset values to Execution Context Stack registers */ 370 for (val = 0; val < ARRAY_SIZE(ecs_reset); val++) 371 npe_cmd_write(npe, ecs_reset[val].reg, CMD_WR_ECS_REG, 372 ecs_reset[val].val); 373 374 /* clear the profile counter */ 375 __raw_writel(CMD_CLR_PROFILE_CNT, &npe->regs->exec_status_cmd); 376 377 __raw_writel(0, &npe->regs->exec_count); 378 __raw_writel(0, &npe->regs->action_points[0]); 379 __raw_writel(0, &npe->regs->action_points[1]); 380 __raw_writel(0, &npe->regs->action_points[2]); 381 __raw_writel(0, &npe->regs->action_points[3]); 382 __raw_writel(0, &npe->regs->watch_count); 383 384 val = ixp4xx_read_feature_bits(); 385 /* reset the NPE */ 386 ixp4xx_write_feature_bits(val & 387 ~(IXP4XX_FEATURE_RESET_NPEA << npe->id)); 388 /* deassert reset */ 389 ixp4xx_write_feature_bits(val | 390 (IXP4XX_FEATURE_RESET_NPEA << npe->id)); 391 for (i = 0; i < MAX_RETRIES; i++) { 392 if (ixp4xx_read_feature_bits() & 393 (IXP4XX_FEATURE_RESET_NPEA << npe->id)) 394 break; /* NPE is back alive */ 395 udelay(1); 396 } 397 if (i == MAX_RETRIES) 398 return -ETIMEDOUT; 399 400 npe_stop(npe); 401 402 /* restore NPE configuration bus Control Register - parity settings */ 403 __raw_writel(ctl, &npe->regs->messaging_control); 404 return 0; 405 } 406 407 408 int npe_send_message(struct npe *npe, const void *msg, const char *what) 409 { 410 const u32 *send = msg; 411 int cycles = 0; 412 413 debug_msg(npe, "Trying to send message %s [%08X:%08X]\n", 414 what, send[0], send[1]); 415 416 if (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_IFNE) { 417 debug_msg(npe, "NPE input FIFO not empty\n"); 418 return -EIO; 419 } 420 421 __raw_writel(send[0], &npe->regs->in_out_fifo); 422 423 if (!(__raw_readl(&npe->regs->messaging_status) & MSGSTAT_IFNF)) { 424 debug_msg(npe, "NPE input FIFO full\n"); 425 return -EIO; 426 } 427 428 __raw_writel(send[1], &npe->regs->in_out_fifo); 429 430 while ((cycles < MAX_RETRIES) && 431 (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_IFNE)) { 432 udelay(1); 433 cycles++; 434 } 435 436 if (cycles == MAX_RETRIES) { 437 debug_msg(npe, "Timeout sending message\n"); 438 return -ETIMEDOUT; 439 } 440 441 #if DEBUG_MSG > 1 442 debug_msg(npe, "Sending a message took %i cycles\n", cycles); 443 #endif 444 return 0; 445 } 446 447 int npe_recv_message(struct npe *npe, void *msg, const char *what) 448 { 449 u32 *recv = msg; 450 int cycles = 0, cnt = 0; 451 452 debug_msg(npe, "Trying to receive message %s\n", what); 453 454 while (cycles < MAX_RETRIES) { 455 if (__raw_readl(&npe->regs->messaging_status) & MSGSTAT_OFNE) { 456 recv[cnt++] = __raw_readl(&npe->regs->in_out_fifo); 457 if (cnt == 2) 458 break; 459 } else { 460 udelay(1); 461 cycles++; 462 } 463 } 464 465 switch(cnt) { 466 case 1: 467 debug_msg(npe, "Received [%08X]\n", recv[0]); 468 break; 469 case 2: 470 debug_msg(npe, "Received [%08X:%08X]\n", recv[0], recv[1]); 471 break; 472 } 473 474 if (cycles == MAX_RETRIES) { 475 debug_msg(npe, "Timeout waiting for message\n"); 476 return -ETIMEDOUT; 477 } 478 479 #if DEBUG_MSG > 1 480 debug_msg(npe, "Receiving a message took %i cycles\n", cycles); 481 #endif 482 return 0; 483 } 484 485 int npe_send_recv_message(struct npe *npe, void *msg, const char *what) 486 { 487 int result; 488 u32 *send = msg, recv[2]; 489 490 if ((result = npe_send_message(npe, msg, what)) != 0) 491 return result; 492 if ((result = npe_recv_message(npe, recv, what)) != 0) 493 return result; 494 495 if ((recv[0] != send[0]) || (recv[1] != send[1])) { 496 debug_msg(npe, "Message %s: unexpected message received\n", 497 what); 498 return -EIO; 499 } 500 return 0; 501 } 502 503 504 int npe_load_firmware(struct npe *npe, const char *name, struct device *dev) 505 { 506 const struct firmware *fw_entry; 507 508 struct dl_block { 509 u32 type; 510 u32 offset; 511 } *blk; 512 513 struct dl_image { 514 u32 magic; 515 u32 id; 516 u32 size; 517 union { 518 u32 data[0]; 519 struct dl_block blocks[0]; 520 }; 521 } *image; 522 523 struct dl_codeblock { 524 u32 npe_addr; 525 u32 size; 526 u32 data[0]; 527 } *cb; 528 529 int i, j, err, data_size, instr_size, blocks, table_end; 530 u32 cmd; 531 532 if ((err = request_firmware(&fw_entry, name, dev)) != 0) 533 return err; 534 535 err = -EINVAL; 536 if (fw_entry->size < sizeof(struct dl_image)) { 537 print_npe(KERN_ERR, npe, "incomplete firmware file\n"); 538 goto err; 539 } 540 image = (struct dl_image*)fw_entry->data; 541 542 #if DEBUG_FW 543 print_npe(KERN_DEBUG, npe, "firmware: %08X %08X %08X (0x%X bytes)\n", 544 image->magic, image->id, image->size, image->size * 4); 545 #endif 546 547 if (image->magic == swab32(FW_MAGIC)) { /* swapped file */ 548 image->id = swab32(image->id); 549 image->size = swab32(image->size); 550 } else if (image->magic != FW_MAGIC) { 551 print_npe(KERN_ERR, npe, "bad firmware file magic: 0x%X\n", 552 image->magic); 553 goto err; 554 } 555 if ((image->size * 4 + sizeof(struct dl_image)) != fw_entry->size) { 556 print_npe(KERN_ERR, npe, 557 "inconsistent size of firmware file\n"); 558 goto err; 559 } 560 if (((image->id >> 24) & 0xF /* NPE ID */) != npe->id) { 561 print_npe(KERN_ERR, npe, "firmware file NPE ID mismatch\n"); 562 goto err; 563 } 564 if (image->magic == swab32(FW_MAGIC)) 565 for (i = 0; i < image->size; i++) 566 image->data[i] = swab32(image->data[i]); 567 568 if (cpu_is_ixp42x() && ((image->id >> 28) & 0xF /* device ID */)) { 569 print_npe(KERN_INFO, npe, "IXP43x/IXP46x firmware ignored on " 570 "IXP42x\n"); 571 goto err; 572 } 573 574 if (npe_running(npe)) { 575 print_npe(KERN_INFO, npe, "unable to load firmware, NPE is " 576 "already running\n"); 577 err = -EBUSY; 578 goto err; 579 } 580 #if 0 581 npe_stop(npe); 582 npe_reset(npe); 583 #endif 584 585 print_npe(KERN_INFO, npe, "firmware functionality 0x%X, " 586 "revision 0x%X:%X\n", (image->id >> 16) & 0xFF, 587 (image->id >> 8) & 0xFF, image->id & 0xFF); 588 589 if (cpu_is_ixp42x()) { 590 if (!npe->id) 591 instr_size = NPE_A_42X_INSTR_SIZE; 592 else 593 instr_size = NPE_B_AND_C_42X_INSTR_SIZE; 594 data_size = NPE_42X_DATA_SIZE; 595 } else { 596 instr_size = NPE_46X_INSTR_SIZE; 597 data_size = NPE_46X_DATA_SIZE; 598 } 599 600 for (blocks = 0; blocks * sizeof(struct dl_block) / 4 < image->size; 601 blocks++) 602 if (image->blocks[blocks].type == FW_BLOCK_TYPE_EOF) 603 break; 604 if (blocks * sizeof(struct dl_block) / 4 >= image->size) { 605 print_npe(KERN_INFO, npe, "firmware EOF block marker not " 606 "found\n"); 607 goto err; 608 } 609 610 #if DEBUG_FW 611 print_npe(KERN_DEBUG, npe, "%i firmware blocks found\n", blocks); 612 #endif 613 614 table_end = blocks * sizeof(struct dl_block) / 4 + 1 /* EOF marker */; 615 for (i = 0, blk = image->blocks; i < blocks; i++, blk++) { 616 if (blk->offset > image->size - sizeof(struct dl_codeblock) / 4 617 || blk->offset < table_end) { 618 print_npe(KERN_INFO, npe, "invalid offset 0x%X of " 619 "firmware block #%i\n", blk->offset, i); 620 goto err; 621 } 622 623 cb = (struct dl_codeblock*)&image->data[blk->offset]; 624 if (blk->type == FW_BLOCK_TYPE_INSTR) { 625 if (cb->npe_addr + cb->size > instr_size) 626 goto too_big; 627 cmd = CMD_WR_INS_MEM; 628 } else if (blk->type == FW_BLOCK_TYPE_DATA) { 629 if (cb->npe_addr + cb->size > data_size) 630 goto too_big; 631 cmd = CMD_WR_DATA_MEM; 632 } else { 633 print_npe(KERN_INFO, npe, "invalid firmware block #%i " 634 "type 0x%X\n", i, blk->type); 635 goto err; 636 } 637 if (blk->offset + sizeof(*cb) / 4 + cb->size > image->size) { 638 print_npe(KERN_INFO, npe, "firmware block #%i doesn't " 639 "fit in firmware image: type %c, start 0x%X," 640 " length 0x%X\n", i, 641 blk->type == FW_BLOCK_TYPE_INSTR ? 'I' : 'D', 642 cb->npe_addr, cb->size); 643 goto err; 644 } 645 646 for (j = 0; j < cb->size; j++) 647 npe_cmd_write(npe, cb->npe_addr + j, cmd, cb->data[j]); 648 } 649 650 npe_start(npe); 651 if (!npe_running(npe)) 652 print_npe(KERN_ERR, npe, "unable to start\n"); 653 release_firmware(fw_entry); 654 return 0; 655 656 too_big: 657 print_npe(KERN_INFO, npe, "firmware block #%i doesn't fit in NPE " 658 "memory: type %c, start 0x%X, length 0x%X\n", i, 659 blk->type == FW_BLOCK_TYPE_INSTR ? 'I' : 'D', 660 cb->npe_addr, cb->size); 661 err: 662 release_firmware(fw_entry); 663 return err; 664 } 665 666 667 struct npe *npe_request(unsigned id) 668 { 669 if (id < NPE_COUNT) 670 if (npe_tab[id].valid) 671 if (try_module_get(THIS_MODULE)) 672 return &npe_tab[id]; 673 return NULL; 674 } 675 676 void npe_release(struct npe *npe) 677 { 678 module_put(THIS_MODULE); 679 } 680 681 static int ixp4xx_npe_probe(struct platform_device *pdev) 682 { 683 int i, found = 0; 684 struct device *dev = &pdev->dev; 685 struct device_node *np = dev->of_node; 686 struct resource *res; 687 688 for (i = 0; i < NPE_COUNT; i++) { 689 struct npe *npe = &npe_tab[i]; 690 691 res = platform_get_resource(pdev, IORESOURCE_MEM, i); 692 if (!res) 693 return -ENODEV; 694 695 if (!(ixp4xx_read_feature_bits() & 696 (IXP4XX_FEATURE_RESET_NPEA << i))) { 697 dev_info(dev, "NPE%d at 0x%08x-0x%08x not available\n", 698 i, res->start, res->end); 699 continue; /* NPE already disabled or not present */ 700 } 701 npe->regs = devm_ioremap_resource(dev, res); 702 if (IS_ERR(npe->regs)) 703 return PTR_ERR(npe->regs); 704 705 if (npe_reset(npe)) { 706 dev_info(dev, "NPE%d at 0x%08x-0x%08x does not reset\n", 707 i, res->start, res->end); 708 continue; 709 } 710 npe->valid = 1; 711 dev_info(dev, "NPE%d at 0x%08x-0x%08x registered\n", 712 i, res->start, res->end); 713 found++; 714 } 715 716 if (!found) 717 return -ENODEV; 718 719 /* Spawn crypto subdevice if using device tree */ 720 if (IS_ENABLED(CONFIG_OF) && np) 721 devm_of_platform_populate(dev); 722 723 return 0; 724 } 725 726 static int ixp4xx_npe_remove(struct platform_device *pdev) 727 { 728 int i; 729 730 for (i = 0; i < NPE_COUNT; i++) 731 if (npe_tab[i].regs) { 732 npe_reset(&npe_tab[i]); 733 } 734 735 return 0; 736 } 737 738 static const struct of_device_id ixp4xx_npe_of_match[] = { 739 { 740 .compatible = "intel,ixp4xx-network-processing-engine", 741 }, 742 {}, 743 }; 744 745 static struct platform_driver ixp4xx_npe_driver = { 746 .driver = { 747 .name = "ixp4xx-npe", 748 .of_match_table = of_match_ptr(ixp4xx_npe_of_match), 749 }, 750 .probe = ixp4xx_npe_probe, 751 .remove = ixp4xx_npe_remove, 752 }; 753 module_platform_driver(ixp4xx_npe_driver); 754 755 MODULE_AUTHOR("Krzysztof Halasa"); 756 MODULE_LICENSE("GPL v2"); 757 MODULE_FIRMWARE(NPE_A_FIRMWARE); 758 MODULE_FIRMWARE(NPE_B_FIRMWARE); 759 MODULE_FIRMWARE(NPE_C_FIRMWARE); 760 761 EXPORT_SYMBOL(npe_names); 762 EXPORT_SYMBOL(npe_running); 763 EXPORT_SYMBOL(npe_request); 764 EXPORT_SYMBOL(npe_release); 765 EXPORT_SYMBOL(npe_load_firmware); 766 EXPORT_SYMBOL(npe_send_message); 767 EXPORT_SYMBOL(npe_recv_message); 768 EXPORT_SYMBOL(npe_send_recv_message); 769