1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * SCSI Enclosure Services 4 * 5 * Copyright (C) 2008 James Bottomley <James.Bottomley@HansenPartnership.com> 6 */ 7 8 #include <linux/slab.h> 9 #include <linux/module.h> 10 #include <linux/kernel.h> 11 #include <linux/enclosure.h> 12 #include <asm/unaligned.h> 13 14 #include <scsi/scsi.h> 15 #include <scsi/scsi_cmnd.h> 16 #include <scsi/scsi_dbg.h> 17 #include <scsi/scsi_device.h> 18 #include <scsi/scsi_driver.h> 19 #include <scsi/scsi_host.h> 20 21 #include <scsi/scsi_transport_sas.h> 22 23 struct ses_device { 24 unsigned char *page1; 25 unsigned char *page1_types; 26 unsigned char *page2; 27 unsigned char *page10; 28 short page1_len; 29 short page1_num_types; 30 short page2_len; 31 short page10_len; 32 }; 33 34 struct ses_component { 35 u64 addr; 36 }; 37 38 static bool ses_page2_supported(struct enclosure_device *edev) 39 { 40 struct ses_device *ses_dev = edev->scratch; 41 42 return (ses_dev->page2 != NULL); 43 } 44 45 static int ses_probe(struct device *dev) 46 { 47 struct scsi_device *sdev = to_scsi_device(dev); 48 int err = -ENODEV; 49 50 if (sdev->type != TYPE_ENCLOSURE) 51 goto out; 52 53 err = 0; 54 sdev_printk(KERN_NOTICE, sdev, "Attached Enclosure device\n"); 55 56 out: 57 return err; 58 } 59 60 #define SES_TIMEOUT (30 * HZ) 61 #define SES_RETRIES 3 62 63 static void init_device_slot_control(unsigned char *dest_desc, 64 struct enclosure_component *ecomp, 65 unsigned char *status) 66 { 67 memcpy(dest_desc, status, 4); 68 dest_desc[0] = 0; 69 /* only clear byte 1 for ENCLOSURE_COMPONENT_DEVICE */ 70 if (ecomp->type == ENCLOSURE_COMPONENT_DEVICE) 71 dest_desc[1] = 0; 72 dest_desc[2] &= 0xde; 73 dest_desc[3] &= 0x3c; 74 } 75 76 77 static int ses_recv_diag(struct scsi_device *sdev, int page_code, 78 void *buf, int bufflen) 79 { 80 int ret; 81 unsigned char cmd[] = { 82 RECEIVE_DIAGNOSTIC, 83 1, /* Set PCV bit */ 84 page_code, 85 bufflen >> 8, 86 bufflen & 0xff, 87 0 88 }; 89 unsigned char recv_page_code; 90 struct scsi_failure failure_defs[] = { 91 { 92 .sense = UNIT_ATTENTION, 93 .asc = 0x29, 94 .ascq = SCMD_FAILURE_ASCQ_ANY, 95 .allowed = SES_RETRIES, 96 .result = SAM_STAT_CHECK_CONDITION, 97 }, 98 { 99 .sense = NOT_READY, 100 .asc = SCMD_FAILURE_ASC_ANY, 101 .ascq = SCMD_FAILURE_ASCQ_ANY, 102 .allowed = SES_RETRIES, 103 .result = SAM_STAT_CHECK_CONDITION, 104 }, 105 {} 106 }; 107 struct scsi_failures failures = { 108 .failure_definitions = failure_defs, 109 }; 110 const struct scsi_exec_args exec_args = { 111 .failures = &failures, 112 }; 113 114 ret = scsi_execute_cmd(sdev, cmd, REQ_OP_DRV_IN, buf, bufflen, 115 SES_TIMEOUT, 1, &exec_args); 116 if (unlikely(ret)) 117 return ret; 118 119 recv_page_code = ((unsigned char *)buf)[0]; 120 121 if (likely(recv_page_code == page_code)) 122 return ret; 123 124 /* successful diagnostic but wrong page code. This happens to some 125 * USB devices, just print a message and pretend there was an error */ 126 127 sdev_printk(KERN_ERR, sdev, 128 "Wrong diagnostic page; asked for %d got %u\n", 129 page_code, recv_page_code); 130 131 return -EINVAL; 132 } 133 134 static int ses_send_diag(struct scsi_device *sdev, int page_code, 135 void *buf, int bufflen) 136 { 137 int result; 138 139 unsigned char cmd[] = { 140 SEND_DIAGNOSTIC, 141 0x10, /* Set PF bit */ 142 0, 143 bufflen >> 8, 144 bufflen & 0xff, 145 0 146 }; 147 struct scsi_failure failure_defs[] = { 148 { 149 .sense = UNIT_ATTENTION, 150 .asc = 0x29, 151 .ascq = SCMD_FAILURE_ASCQ_ANY, 152 .allowed = SES_RETRIES, 153 .result = SAM_STAT_CHECK_CONDITION, 154 }, 155 { 156 .sense = NOT_READY, 157 .asc = SCMD_FAILURE_ASC_ANY, 158 .ascq = SCMD_FAILURE_ASCQ_ANY, 159 .allowed = SES_RETRIES, 160 .result = SAM_STAT_CHECK_CONDITION, 161 }, 162 {} 163 }; 164 struct scsi_failures failures = { 165 .failure_definitions = failure_defs, 166 }; 167 const struct scsi_exec_args exec_args = { 168 .failures = &failures, 169 }; 170 171 result = scsi_execute_cmd(sdev, cmd, REQ_OP_DRV_OUT, buf, bufflen, 172 SES_TIMEOUT, 1, &exec_args); 173 if (result) 174 sdev_printk(KERN_ERR, sdev, "SEND DIAGNOSTIC result: %8x\n", 175 result); 176 return result; 177 } 178 179 static int ses_set_page2_descriptor(struct enclosure_device *edev, 180 struct enclosure_component *ecomp, 181 unsigned char *desc) 182 { 183 int i, j, count = 0, descriptor = ecomp->number; 184 struct scsi_device *sdev = to_scsi_device(edev->edev.parent); 185 struct ses_device *ses_dev = edev->scratch; 186 unsigned char *type_ptr = ses_dev->page1_types; 187 unsigned char *desc_ptr = ses_dev->page2 + 8; 188 189 /* Clear everything */ 190 memset(desc_ptr, 0, ses_dev->page2_len - 8); 191 for (i = 0; i < ses_dev->page1_num_types; i++, type_ptr += 4) { 192 for (j = 0; j < type_ptr[1]; j++) { 193 desc_ptr += 4; 194 if (type_ptr[0] != ENCLOSURE_COMPONENT_DEVICE && 195 type_ptr[0] != ENCLOSURE_COMPONENT_ARRAY_DEVICE) 196 continue; 197 if (count++ == descriptor) { 198 memcpy(desc_ptr, desc, 4); 199 /* set select */ 200 desc_ptr[0] |= 0x80; 201 /* clear reserved, just in case */ 202 desc_ptr[0] &= 0xf0; 203 } 204 } 205 } 206 207 return ses_send_diag(sdev, 2, ses_dev->page2, ses_dev->page2_len); 208 } 209 210 static unsigned char *ses_get_page2_descriptor(struct enclosure_device *edev, 211 struct enclosure_component *ecomp) 212 { 213 int i, j, count = 0, descriptor = ecomp->number; 214 struct scsi_device *sdev = to_scsi_device(edev->edev.parent); 215 struct ses_device *ses_dev = edev->scratch; 216 unsigned char *type_ptr = ses_dev->page1_types; 217 unsigned char *desc_ptr = ses_dev->page2 + 8; 218 219 if (ses_recv_diag(sdev, 2, ses_dev->page2, ses_dev->page2_len) < 0) 220 return NULL; 221 222 for (i = 0; i < ses_dev->page1_num_types; i++, type_ptr += 4) { 223 for (j = 0; j < type_ptr[1]; j++) { 224 desc_ptr += 4; 225 if (type_ptr[0] != ENCLOSURE_COMPONENT_DEVICE && 226 type_ptr[0] != ENCLOSURE_COMPONENT_ARRAY_DEVICE) 227 continue; 228 if (count++ == descriptor) 229 return desc_ptr; 230 } 231 } 232 return NULL; 233 } 234 235 /* For device slot and array device slot elements, byte 3 bit 6 236 * is "fault sensed" while byte 3 bit 5 is "fault reqstd". As this 237 * code stands these bits are shifted 4 positions right so in 238 * sysfs they will appear as bits 2 and 1 respectively. Strange. */ 239 static void ses_get_fault(struct enclosure_device *edev, 240 struct enclosure_component *ecomp) 241 { 242 unsigned char *desc; 243 244 if (!ses_page2_supported(edev)) { 245 ecomp->fault = 0; 246 return; 247 } 248 desc = ses_get_page2_descriptor(edev, ecomp); 249 if (desc) 250 ecomp->fault = (desc[3] & 0x60) >> 4; 251 } 252 253 static int ses_set_fault(struct enclosure_device *edev, 254 struct enclosure_component *ecomp, 255 enum enclosure_component_setting val) 256 { 257 unsigned char desc[4]; 258 unsigned char *desc_ptr; 259 260 if (!ses_page2_supported(edev)) 261 return -EINVAL; 262 263 desc_ptr = ses_get_page2_descriptor(edev, ecomp); 264 265 if (!desc_ptr) 266 return -EIO; 267 268 init_device_slot_control(desc, ecomp, desc_ptr); 269 270 switch (val) { 271 case ENCLOSURE_SETTING_DISABLED: 272 desc[3] &= 0xdf; 273 break; 274 case ENCLOSURE_SETTING_ENABLED: 275 desc[3] |= 0x20; 276 break; 277 default: 278 /* SES doesn't do the SGPIO blink settings */ 279 return -EINVAL; 280 } 281 282 return ses_set_page2_descriptor(edev, ecomp, desc); 283 } 284 285 static void ses_get_status(struct enclosure_device *edev, 286 struct enclosure_component *ecomp) 287 { 288 unsigned char *desc; 289 290 if (!ses_page2_supported(edev)) { 291 ecomp->status = 0; 292 return; 293 } 294 desc = ses_get_page2_descriptor(edev, ecomp); 295 if (desc) 296 ecomp->status = (desc[0] & 0x0f); 297 } 298 299 static void ses_get_locate(struct enclosure_device *edev, 300 struct enclosure_component *ecomp) 301 { 302 unsigned char *desc; 303 304 if (!ses_page2_supported(edev)) { 305 ecomp->locate = 0; 306 return; 307 } 308 desc = ses_get_page2_descriptor(edev, ecomp); 309 if (desc) 310 ecomp->locate = (desc[2] & 0x02) ? 1 : 0; 311 } 312 313 static int ses_set_locate(struct enclosure_device *edev, 314 struct enclosure_component *ecomp, 315 enum enclosure_component_setting val) 316 { 317 unsigned char desc[4]; 318 unsigned char *desc_ptr; 319 320 if (!ses_page2_supported(edev)) 321 return -EINVAL; 322 323 desc_ptr = ses_get_page2_descriptor(edev, ecomp); 324 325 if (!desc_ptr) 326 return -EIO; 327 328 init_device_slot_control(desc, ecomp, desc_ptr); 329 330 switch (val) { 331 case ENCLOSURE_SETTING_DISABLED: 332 desc[2] &= 0xfd; 333 break; 334 case ENCLOSURE_SETTING_ENABLED: 335 desc[2] |= 0x02; 336 break; 337 default: 338 /* SES doesn't do the SGPIO blink settings */ 339 return -EINVAL; 340 } 341 return ses_set_page2_descriptor(edev, ecomp, desc); 342 } 343 344 static int ses_set_active(struct enclosure_device *edev, 345 struct enclosure_component *ecomp, 346 enum enclosure_component_setting val) 347 { 348 unsigned char desc[4]; 349 unsigned char *desc_ptr; 350 351 if (!ses_page2_supported(edev)) 352 return -EINVAL; 353 354 desc_ptr = ses_get_page2_descriptor(edev, ecomp); 355 356 if (!desc_ptr) 357 return -EIO; 358 359 init_device_slot_control(desc, ecomp, desc_ptr); 360 361 switch (val) { 362 case ENCLOSURE_SETTING_DISABLED: 363 desc[2] &= 0x7f; 364 ecomp->active = 0; 365 break; 366 case ENCLOSURE_SETTING_ENABLED: 367 desc[2] |= 0x80; 368 ecomp->active = 1; 369 break; 370 default: 371 /* SES doesn't do the SGPIO blink settings */ 372 return -EINVAL; 373 } 374 return ses_set_page2_descriptor(edev, ecomp, desc); 375 } 376 377 static int ses_show_id(struct enclosure_device *edev, char *buf) 378 { 379 struct ses_device *ses_dev = edev->scratch; 380 unsigned long long id = get_unaligned_be64(ses_dev->page1+8+4); 381 382 return sprintf(buf, "%#llx\n", id); 383 } 384 385 static void ses_get_power_status(struct enclosure_device *edev, 386 struct enclosure_component *ecomp) 387 { 388 unsigned char *desc; 389 390 if (!ses_page2_supported(edev)) { 391 ecomp->power_status = 0; 392 return; 393 } 394 395 desc = ses_get_page2_descriptor(edev, ecomp); 396 if (desc) 397 ecomp->power_status = (desc[3] & 0x10) ? 0 : 1; 398 } 399 400 static int ses_set_power_status(struct enclosure_device *edev, 401 struct enclosure_component *ecomp, 402 int val) 403 { 404 unsigned char desc[4]; 405 unsigned char *desc_ptr; 406 407 if (!ses_page2_supported(edev)) 408 return -EINVAL; 409 410 desc_ptr = ses_get_page2_descriptor(edev, ecomp); 411 412 if (!desc_ptr) 413 return -EIO; 414 415 init_device_slot_control(desc, ecomp, desc_ptr); 416 417 switch (val) { 418 /* power = 1 is device_off = 0 and vice versa */ 419 case 0: 420 desc[3] |= 0x10; 421 break; 422 case 1: 423 desc[3] &= 0xef; 424 break; 425 default: 426 return -EINVAL; 427 } 428 ecomp->power_status = val; 429 return ses_set_page2_descriptor(edev, ecomp, desc); 430 } 431 432 static struct enclosure_component_callbacks ses_enclosure_callbacks = { 433 .get_fault = ses_get_fault, 434 .set_fault = ses_set_fault, 435 .get_status = ses_get_status, 436 .get_locate = ses_get_locate, 437 .set_locate = ses_set_locate, 438 .get_power_status = ses_get_power_status, 439 .set_power_status = ses_set_power_status, 440 .set_active = ses_set_active, 441 .show_id = ses_show_id, 442 }; 443 444 struct ses_host_edev { 445 struct Scsi_Host *shost; 446 struct enclosure_device *edev; 447 }; 448 449 #if 0 450 int ses_match_host(struct enclosure_device *edev, void *data) 451 { 452 struct ses_host_edev *sed = data; 453 struct scsi_device *sdev; 454 455 if (!scsi_is_sdev_device(edev->edev.parent)) 456 return 0; 457 458 sdev = to_scsi_device(edev->edev.parent); 459 460 if (sdev->host != sed->shost) 461 return 0; 462 463 sed->edev = edev; 464 return 1; 465 } 466 #endif /* 0 */ 467 468 static int ses_process_descriptor(struct enclosure_component *ecomp, 469 unsigned char *desc, int max_desc_len) 470 { 471 int eip = desc[0] & 0x10; 472 int invalid = desc[0] & 0x80; 473 enum scsi_protocol proto = desc[0] & 0x0f; 474 u64 addr = 0; 475 int slot = -1; 476 struct ses_component *scomp = ecomp->scratch; 477 unsigned char *d; 478 479 if (invalid) 480 return 0; 481 482 switch (proto) { 483 case SCSI_PROTOCOL_FCP: 484 if (eip) { 485 if (max_desc_len <= 7) 486 return 1; 487 d = desc + 4; 488 slot = d[3]; 489 } 490 break; 491 case SCSI_PROTOCOL_SAS: 492 493 if (eip) { 494 if (max_desc_len <= 27) 495 return 1; 496 d = desc + 4; 497 slot = d[3]; 498 d = desc + 8; 499 } else { 500 if (max_desc_len <= 23) 501 return 1; 502 d = desc + 4; 503 } 504 505 506 /* only take the phy0 addr */ 507 addr = (u64)d[12] << 56 | 508 (u64)d[13] << 48 | 509 (u64)d[14] << 40 | 510 (u64)d[15] << 32 | 511 (u64)d[16] << 24 | 512 (u64)d[17] << 16 | 513 (u64)d[18] << 8 | 514 (u64)d[19]; 515 break; 516 default: 517 /* FIXME: Need to add more protocols than just SAS */ 518 break; 519 } 520 ecomp->slot = slot; 521 scomp->addr = addr; 522 523 return 0; 524 } 525 526 struct efd { 527 u64 addr; 528 struct device *dev; 529 }; 530 531 static int ses_enclosure_find_by_addr(struct enclosure_device *edev, 532 void *data) 533 { 534 struct efd *efd = data; 535 int i; 536 struct ses_component *scomp; 537 538 for (i = 0; i < edev->components; i++) { 539 scomp = edev->component[i].scratch; 540 if (scomp->addr != efd->addr) 541 continue; 542 543 if (enclosure_add_device(edev, i, efd->dev) == 0) 544 kobject_uevent(&efd->dev->kobj, KOBJ_CHANGE); 545 return 1; 546 } 547 return 0; 548 } 549 550 #define INIT_ALLOC_SIZE 32 551 552 static void ses_enclosure_data_process(struct enclosure_device *edev, 553 struct scsi_device *sdev, 554 int create) 555 { 556 u32 result; 557 unsigned char *buf = NULL, *type_ptr, *desc_ptr, *addl_desc_ptr = NULL; 558 int i, j, page7_len, len, components; 559 struct ses_device *ses_dev = edev->scratch; 560 int types = ses_dev->page1_num_types; 561 unsigned char *hdr_buf = kzalloc(INIT_ALLOC_SIZE, GFP_KERNEL); 562 563 if (!hdr_buf) 564 goto simple_populate; 565 566 /* re-read page 10 */ 567 if (ses_dev->page10) 568 ses_recv_diag(sdev, 10, ses_dev->page10, ses_dev->page10_len); 569 /* Page 7 for the descriptors is optional */ 570 result = ses_recv_diag(sdev, 7, hdr_buf, INIT_ALLOC_SIZE); 571 if (result) 572 goto simple_populate; 573 574 page7_len = len = (hdr_buf[2] << 8) + hdr_buf[3] + 4; 575 /* add 1 for trailing '\0' we'll use */ 576 buf = kzalloc(len + 1, GFP_KERNEL); 577 if (!buf) 578 goto simple_populate; 579 result = ses_recv_diag(sdev, 7, buf, len); 580 if (result) { 581 simple_populate: 582 kfree(buf); 583 buf = NULL; 584 desc_ptr = NULL; 585 len = 0; 586 page7_len = 0; 587 } else { 588 desc_ptr = buf + 8; 589 len = (desc_ptr[2] << 8) + desc_ptr[3]; 590 /* skip past overall descriptor */ 591 desc_ptr += len + 4; 592 } 593 if (ses_dev->page10 && ses_dev->page10_len > 9) 594 addl_desc_ptr = ses_dev->page10 + 8; 595 type_ptr = ses_dev->page1_types; 596 components = 0; 597 for (i = 0; i < types; i++, type_ptr += 4) { 598 for (j = 0; j < type_ptr[1]; j++) { 599 char *name = NULL; 600 struct enclosure_component *ecomp; 601 int max_desc_len; 602 603 if (desc_ptr) { 604 if (desc_ptr + 3 >= buf + page7_len) { 605 desc_ptr = NULL; 606 } else { 607 len = (desc_ptr[2] << 8) + desc_ptr[3]; 608 desc_ptr += 4; 609 if (desc_ptr + len > buf + page7_len) 610 desc_ptr = NULL; 611 else { 612 /* Add trailing zero - pushes into 613 * reserved space */ 614 desc_ptr[len] = '\0'; 615 name = desc_ptr; 616 } 617 } 618 } 619 if (type_ptr[0] == ENCLOSURE_COMPONENT_DEVICE || 620 type_ptr[0] == ENCLOSURE_COMPONENT_ARRAY_DEVICE) { 621 622 if (create) 623 ecomp = enclosure_component_alloc( 624 edev, 625 components++, 626 type_ptr[0], 627 name); 628 else if (components < edev->components) 629 ecomp = &edev->component[components++]; 630 else 631 ecomp = ERR_PTR(-EINVAL); 632 633 if (!IS_ERR(ecomp)) { 634 if (addl_desc_ptr) { 635 max_desc_len = ses_dev->page10_len - 636 (addl_desc_ptr - ses_dev->page10); 637 if (ses_process_descriptor(ecomp, 638 addl_desc_ptr, 639 max_desc_len)) 640 addl_desc_ptr = NULL; 641 } 642 if (create) 643 enclosure_component_register( 644 ecomp); 645 } 646 } 647 if (desc_ptr) 648 desc_ptr += len; 649 650 if (addl_desc_ptr && 651 /* only find additional descriptions for specific devices */ 652 (type_ptr[0] == ENCLOSURE_COMPONENT_DEVICE || 653 type_ptr[0] == ENCLOSURE_COMPONENT_ARRAY_DEVICE || 654 type_ptr[0] == ENCLOSURE_COMPONENT_SAS_EXPANDER || 655 /* these elements are optional */ 656 type_ptr[0] == ENCLOSURE_COMPONENT_SCSI_TARGET_PORT || 657 type_ptr[0] == ENCLOSURE_COMPONENT_SCSI_INITIATOR_PORT || 658 type_ptr[0] == ENCLOSURE_COMPONENT_CONTROLLER_ELECTRONICS)) { 659 addl_desc_ptr += addl_desc_ptr[1] + 2; 660 if (addl_desc_ptr + 1 >= ses_dev->page10 + ses_dev->page10_len) 661 addl_desc_ptr = NULL; 662 } 663 } 664 } 665 kfree(buf); 666 kfree(hdr_buf); 667 } 668 669 static void ses_match_to_enclosure(struct enclosure_device *edev, 670 struct scsi_device *sdev, 671 int refresh) 672 { 673 struct scsi_device *edev_sdev = to_scsi_device(edev->edev.parent); 674 struct efd efd = { 675 .addr = 0, 676 }; 677 678 if (refresh) 679 ses_enclosure_data_process(edev, edev_sdev, 0); 680 681 if (scsi_is_sas_rphy(sdev->sdev_target->dev.parent)) 682 efd.addr = sas_get_address(sdev); 683 684 if (efd.addr) { 685 efd.dev = &sdev->sdev_gendev; 686 687 enclosure_for_each_device(ses_enclosure_find_by_addr, &efd); 688 } 689 } 690 691 static int ses_intf_add(struct device *cdev) 692 { 693 struct scsi_device *sdev = to_scsi_device(cdev->parent); 694 struct scsi_device *tmp_sdev; 695 unsigned char *buf = NULL, *hdr_buf, *type_ptr, page; 696 struct ses_device *ses_dev; 697 u32 result; 698 int i, types, len, components = 0; 699 int err = -ENOMEM; 700 int num_enclosures; 701 struct enclosure_device *edev; 702 struct ses_component *scomp = NULL; 703 704 if (!scsi_device_enclosure(sdev)) { 705 /* not an enclosure, but might be in one */ 706 struct enclosure_device *prev = NULL; 707 708 while ((edev = enclosure_find(&sdev->host->shost_gendev, prev)) != NULL) { 709 ses_match_to_enclosure(edev, sdev, 1); 710 prev = edev; 711 } 712 return -ENODEV; 713 } 714 715 /* TYPE_ENCLOSURE prints a message in probe */ 716 if (sdev->type != TYPE_ENCLOSURE) 717 sdev_printk(KERN_NOTICE, sdev, "Embedded Enclosure Device\n"); 718 719 ses_dev = kzalloc(sizeof(*ses_dev), GFP_KERNEL); 720 hdr_buf = kzalloc(INIT_ALLOC_SIZE, GFP_KERNEL); 721 if (!hdr_buf || !ses_dev) 722 goto err_init_free; 723 724 page = 1; 725 result = ses_recv_diag(sdev, page, hdr_buf, INIT_ALLOC_SIZE); 726 if (result) 727 goto recv_failed; 728 729 len = (hdr_buf[2] << 8) + hdr_buf[3] + 4; 730 buf = kzalloc(len, GFP_KERNEL); 731 if (!buf) 732 goto err_free; 733 734 result = ses_recv_diag(sdev, page, buf, len); 735 if (result) 736 goto recv_failed; 737 738 types = 0; 739 740 /* we always have one main enclosure and the rest are referred 741 * to as secondary subenclosures */ 742 num_enclosures = buf[1] + 1; 743 744 /* begin at the enclosure descriptor */ 745 type_ptr = buf + 8; 746 /* skip all the enclosure descriptors */ 747 for (i = 0; i < num_enclosures && type_ptr < buf + len; i++) { 748 types += type_ptr[2]; 749 type_ptr += type_ptr[3] + 4; 750 } 751 752 ses_dev->page1_types = type_ptr; 753 ses_dev->page1_num_types = types; 754 755 for (i = 0; i < types && type_ptr < buf + len; i++, type_ptr += 4) { 756 if (type_ptr[0] == ENCLOSURE_COMPONENT_DEVICE || 757 type_ptr[0] == ENCLOSURE_COMPONENT_ARRAY_DEVICE) 758 components += type_ptr[1]; 759 } 760 761 ses_dev->page1 = buf; 762 ses_dev->page1_len = len; 763 buf = NULL; 764 765 page = 2; 766 result = ses_recv_diag(sdev, page, hdr_buf, INIT_ALLOC_SIZE); 767 if (result) 768 goto page2_not_supported; 769 770 len = (hdr_buf[2] << 8) + hdr_buf[3] + 4; 771 buf = kzalloc(len, GFP_KERNEL); 772 if (!buf) 773 goto err_free; 774 775 /* make sure getting page 2 actually works */ 776 result = ses_recv_diag(sdev, 2, buf, len); 777 if (result) 778 goto recv_failed; 779 ses_dev->page2 = buf; 780 ses_dev->page2_len = len; 781 buf = NULL; 782 783 /* The additional information page --- allows us 784 * to match up the devices */ 785 page = 10; 786 result = ses_recv_diag(sdev, page, hdr_buf, INIT_ALLOC_SIZE); 787 if (!result) { 788 789 len = (hdr_buf[2] << 8) + hdr_buf[3] + 4; 790 buf = kzalloc(len, GFP_KERNEL); 791 if (!buf) 792 goto err_free; 793 794 result = ses_recv_diag(sdev, page, buf, len); 795 if (result) 796 goto recv_failed; 797 ses_dev->page10 = buf; 798 ses_dev->page10_len = len; 799 buf = NULL; 800 } 801 page2_not_supported: 802 if (components > 0) { 803 scomp = kcalloc(components, sizeof(struct ses_component), GFP_KERNEL); 804 if (!scomp) 805 goto err_free; 806 } 807 808 edev = enclosure_register(cdev->parent, dev_name(&sdev->sdev_gendev), 809 components, &ses_enclosure_callbacks); 810 if (IS_ERR(edev)) { 811 err = PTR_ERR(edev); 812 goto err_free; 813 } 814 815 kfree(hdr_buf); 816 817 edev->scratch = ses_dev; 818 for (i = 0; i < components; i++) 819 edev->component[i].scratch = scomp + i; 820 821 ses_enclosure_data_process(edev, sdev, 1); 822 823 /* see if there are any devices matching before 824 * we found the enclosure */ 825 shost_for_each_device(tmp_sdev, sdev->host) { 826 if (tmp_sdev->lun != 0 || scsi_device_enclosure(tmp_sdev)) 827 continue; 828 ses_match_to_enclosure(edev, tmp_sdev, 0); 829 } 830 831 return 0; 832 833 recv_failed: 834 sdev_printk(KERN_ERR, sdev, "Failed to get diagnostic page 0x%x\n", 835 page); 836 err = -ENODEV; 837 err_free: 838 kfree(buf); 839 kfree(scomp); 840 kfree(ses_dev->page10); 841 kfree(ses_dev->page2); 842 kfree(ses_dev->page1); 843 err_init_free: 844 kfree(ses_dev); 845 kfree(hdr_buf); 846 sdev_printk(KERN_ERR, sdev, "Failed to bind enclosure %d\n", err); 847 return err; 848 } 849 850 static int ses_remove(struct device *dev) 851 { 852 return 0; 853 } 854 855 static void ses_intf_remove_component(struct scsi_device *sdev) 856 { 857 struct enclosure_device *edev, *prev = NULL; 858 859 while ((edev = enclosure_find(&sdev->host->shost_gendev, prev)) != NULL) { 860 prev = edev; 861 if (!enclosure_remove_device(edev, &sdev->sdev_gendev)) 862 break; 863 } 864 if (edev) 865 put_device(&edev->edev); 866 } 867 868 static void ses_intf_remove_enclosure(struct scsi_device *sdev) 869 { 870 struct enclosure_device *edev; 871 struct ses_device *ses_dev; 872 873 /* exact match to this enclosure */ 874 edev = enclosure_find(&sdev->sdev_gendev, NULL); 875 if (!edev) 876 return; 877 878 ses_dev = edev->scratch; 879 edev->scratch = NULL; 880 881 kfree(ses_dev->page10); 882 kfree(ses_dev->page1); 883 kfree(ses_dev->page2); 884 kfree(ses_dev); 885 886 if (edev->components) 887 kfree(edev->component[0].scratch); 888 889 put_device(&edev->edev); 890 enclosure_unregister(edev); 891 } 892 893 static void ses_intf_remove(struct device *cdev) 894 { 895 struct scsi_device *sdev = to_scsi_device(cdev->parent); 896 897 if (!scsi_device_enclosure(sdev)) 898 ses_intf_remove_component(sdev); 899 else 900 ses_intf_remove_enclosure(sdev); 901 } 902 903 static struct class_interface ses_interface = { 904 .add_dev = ses_intf_add, 905 .remove_dev = ses_intf_remove, 906 }; 907 908 static struct scsi_driver ses_template = { 909 .gendrv = { 910 .name = "ses", 911 .probe = ses_probe, 912 .remove = ses_remove, 913 }, 914 }; 915 916 static int __init ses_init(void) 917 { 918 int err; 919 920 err = scsi_register_interface(&ses_interface); 921 if (err) 922 return err; 923 924 err = scsi_register_driver(&ses_template.gendrv); 925 if (err) 926 goto out_unreg; 927 928 return 0; 929 930 out_unreg: 931 scsi_unregister_interface(&ses_interface); 932 return err; 933 } 934 935 static void __exit ses_exit(void) 936 { 937 scsi_unregister_driver(&ses_template.gendrv); 938 scsi_unregister_interface(&ses_interface); 939 } 940 941 module_init(ses_init); 942 module_exit(ses_exit); 943 944 MODULE_ALIAS_SCSI_DEVICE(TYPE_ENCLOSURE); 945 946 MODULE_AUTHOR("James Bottomley"); 947 MODULE_DESCRIPTION("SCSI Enclosure Services (ses) driver"); 948 MODULE_LICENSE("GPL v2"); 949