1 /* 2 * PMC-Sierra SPC 8001 SAS/SATA based host adapters driver 3 * 4 * Copyright (c) 2008-2009 USI Co., Ltd. 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions, and the following disclaimer, 12 * without modification. 13 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 14 * substantially similar to the "NO WARRANTY" disclaimer below 15 * ("Disclaimer") and any redistribution must be conditioned upon 16 * including a substantially similar Disclaimer requirement for further 17 * binary redistribution. 18 * 3. Neither the names of the above-listed copyright holders nor the names 19 * of any contributors may be used to endorse or promote products derived 20 * from this software without specific prior written permission. 21 * 22 * Alternatively, this software may be distributed under the terms of the 23 * GNU General Public License ("GPL") version 2 as published by the Free 24 * Software Foundation. 25 * 26 * NO WARRANTY 27 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 28 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 29 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR 30 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 31 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 32 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 33 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 34 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 35 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING 36 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 37 * POSSIBILITY OF SUCH DAMAGES. 38 * 39 */ 40 #ifndef _PMC8001_REG_H_ 41 #define _PMC8001_REG_H_ 42 43 #include <linux/types.h> 44 #include <scsi/libsas.h> 45 46 47 /* for Request Opcode of IOMB */ 48 #define OPC_INB_ECHO 1 /* 0x000 */ 49 #define OPC_INB_PHYSTART 4 /* 0x004 */ 50 #define OPC_INB_PHYSTOP 5 /* 0x005 */ 51 #define OPC_INB_SSPINIIOSTART 6 /* 0x006 */ 52 #define OPC_INB_SSPINITMSTART 7 /* 0x007 */ 53 #define OPC_INB_SSPINIEXTIOSTART 8 /* 0x008 */ 54 #define OPC_INB_DEV_HANDLE_ACCEPT 9 /* 0x009 */ 55 #define OPC_INB_SSPTGTIOSTART 10 /* 0x00A */ 56 #define OPC_INB_SSPTGTRSPSTART 11 /* 0x00B */ 57 #define OPC_INB_SSPINIEDCIOSTART 12 /* 0x00C */ 58 #define OPC_INB_SSPINIEXTEDCIOSTART 13 /* 0x00D */ 59 #define OPC_INB_SSPTGTEDCIOSTART 14 /* 0x00E */ 60 #define OPC_INB_SSP_ABORT 15 /* 0x00F */ 61 #define OPC_INB_DEREG_DEV_HANDLE 16 /* 0x010 */ 62 #define OPC_INB_GET_DEV_HANDLE 17 /* 0x011 */ 63 #define OPC_INB_SMP_REQUEST 18 /* 0x012 */ 64 /* SMP_RESPONSE is removed */ 65 #define OPC_INB_SMP_RESPONSE 19 /* 0x013 */ 66 #define OPC_INB_SMP_ABORT 20 /* 0x014 */ 67 #define OPC_INB_REG_DEV 22 /* 0x016 */ 68 #define OPC_INB_SATA_HOST_OPSTART 23 /* 0x017 */ 69 #define OPC_INB_SATA_ABORT 24 /* 0x018 */ 70 #define OPC_INB_LOCAL_PHY_CONTROL 25 /* 0x019 */ 71 #define OPC_INB_GET_DEV_INFO 26 /* 0x01A */ 72 #define OPC_INB_FW_FLASH_UPDATE 32 /* 0x020 */ 73 #define OPC_INB_GPIO 34 /* 0x022 */ 74 #define OPC_INB_SAS_DIAG_MODE_START_END 35 /* 0x023 */ 75 #define OPC_INB_SAS_DIAG_EXECUTE 36 /* 0x024 */ 76 #define OPC_INB_SAS_HW_EVENT_ACK 37 /* 0x025 */ 77 #define OPC_INB_GET_TIME_STAMP 38 /* 0x026 */ 78 #define OPC_INB_PORT_CONTROL 39 /* 0x027 */ 79 #define OPC_INB_GET_NVMD_DATA 40 /* 0x028 */ 80 #define OPC_INB_SET_NVMD_DATA 41 /* 0x029 */ 81 #define OPC_INB_SET_DEVICE_STATE 42 /* 0x02A */ 82 #define OPC_INB_GET_DEVICE_STATE 43 /* 0x02B */ 83 #define OPC_INB_SET_DEV_INFO 44 /* 0x02C */ 84 #define OPC_INB_SAS_RE_INITIALIZE 45 /* 0x02D */ 85 86 /* for Response Opcode of IOMB */ 87 #define OPC_OUB_ECHO 1 /* 0x001 */ 88 #define OPC_OUB_HW_EVENT 4 /* 0x004 */ 89 #define OPC_OUB_SSP_COMP 5 /* 0x005 */ 90 #define OPC_OUB_SMP_COMP 6 /* 0x006 */ 91 #define OPC_OUB_LOCAL_PHY_CNTRL 7 /* 0x007 */ 92 #define OPC_OUB_DEV_REGIST 10 /* 0x00A */ 93 #define OPC_OUB_DEREG_DEV 11 /* 0x00B */ 94 #define OPC_OUB_GET_DEV_HANDLE 12 /* 0x00C */ 95 #define OPC_OUB_SATA_COMP 13 /* 0x00D */ 96 #define OPC_OUB_SATA_EVENT 14 /* 0x00E */ 97 #define OPC_OUB_SSP_EVENT 15 /* 0x00F */ 98 #define OPC_OUB_DEV_HANDLE_ARRIV 16 /* 0x010 */ 99 /* SMP_RECEIVED Notification is removed */ 100 #define OPC_OUB_SMP_RECV_EVENT 17 /* 0x011 */ 101 #define OPC_OUB_SSP_RECV_EVENT 18 /* 0x012 */ 102 #define OPC_OUB_DEV_INFO 19 /* 0x013 */ 103 #define OPC_OUB_FW_FLASH_UPDATE 20 /* 0x014 */ 104 #define OPC_OUB_GPIO_RESPONSE 22 /* 0x016 */ 105 #define OPC_OUB_GPIO_EVENT 23 /* 0x017 */ 106 #define OPC_OUB_GENERAL_EVENT 24 /* 0x018 */ 107 #define OPC_OUB_SSP_ABORT_RSP 26 /* 0x01A */ 108 #define OPC_OUB_SATA_ABORT_RSP 27 /* 0x01B */ 109 #define OPC_OUB_SAS_DIAG_MODE_START_END 28 /* 0x01C */ 110 #define OPC_OUB_SAS_DIAG_EXECUTE 29 /* 0x01D */ 111 #define OPC_OUB_GET_TIME_STAMP 30 /* 0x01E */ 112 #define OPC_OUB_SAS_HW_EVENT_ACK 31 /* 0x01F */ 113 #define OPC_OUB_PORT_CONTROL 32 /* 0x020 */ 114 #define OPC_OUB_SKIP_ENTRY 33 /* 0x021 */ 115 #define OPC_OUB_SMP_ABORT_RSP 34 /* 0x022 */ 116 #define OPC_OUB_GET_NVMD_DATA 35 /* 0x023 */ 117 #define OPC_OUB_SET_NVMD_DATA 36 /* 0x024 */ 118 #define OPC_OUB_DEVICE_HANDLE_REMOVAL 37 /* 0x025 */ 119 #define OPC_OUB_SET_DEVICE_STATE 38 /* 0x026 */ 120 #define OPC_OUB_GET_DEVICE_STATE 39 /* 0x027 */ 121 #define OPC_OUB_SET_DEV_INFO 40 /* 0x028 */ 122 #define OPC_OUB_SAS_RE_INITIALIZE 41 /* 0x029 */ 123 124 /* for phy start*/ 125 #define SPINHOLD_DISABLE (0x00 << 14) 126 #define SPINHOLD_ENABLE (0x01 << 14) 127 #define LINKMODE_SAS (0x01 << 12) 128 #define LINKMODE_DSATA (0x02 << 12) 129 #define LINKMODE_AUTO (0x03 << 12) 130 #define LINKRATE_15 (0x01 << 8) 131 #define LINKRATE_30 (0x02 << 8) 132 #define LINKRATE_60 (0x04 << 8) 133 134 /* for new SPC controllers MEMBASE III is shared between BIOS and DATA */ 135 #define GSM_SM_BASE 0x4F0000 136 struct mpi_msg_hdr{ 137 __le32 header; /* Bits [11:0] - Message operation code */ 138 /* Bits [15:12] - Message Category */ 139 /* Bits [21:16] - Outboundqueue ID for the 140 operation completion message */ 141 /* Bits [23:22] - Reserved */ 142 /* Bits [28:24] - Buffer Count, indicates how 143 many buffer are allocated for the massage */ 144 /* Bits [30:29] - Reserved */ 145 /* Bits [31] - Message Valid bit */ 146 } __attribute__((packed, aligned(4))); 147 148 149 /* 150 * brief the data structure of PHY Start Command 151 * use to describe enable the phy (64 bytes) 152 */ 153 struct phy_start_req { 154 __le32 tag; 155 __le32 ase_sh_lm_slr_phyid; 156 struct sas_identify_frame sas_identify; 157 u32 reserved[5]; 158 } __attribute__((packed, aligned(4))); 159 160 161 /* 162 * brief the data structure of PHY Start Command 163 * use to disable the phy (64 bytes) 164 */ 165 struct phy_stop_req { 166 __le32 tag; 167 __le32 phy_id; 168 u32 reserved[13]; 169 } __attribute__((packed, aligned(4))); 170 171 172 /* set device bits fis - device to host */ 173 struct set_dev_bits_fis { 174 u8 fis_type; /* 0xA1*/ 175 u8 n_i_pmport; 176 /* b7 : n Bit. Notification bit. If set device needs attention. */ 177 /* b6 : i Bit. Interrupt Bit */ 178 /* b5-b4: reserved2 */ 179 /* b3-b0: PM Port */ 180 u8 status; 181 u8 error; 182 u32 _r_a; 183 } __attribute__ ((packed)); 184 /* PIO setup FIS - device to host */ 185 struct pio_setup_fis { 186 u8 fis_type; /* 0x5f */ 187 u8 i_d_pmPort; 188 /* b7 : reserved */ 189 /* b6 : i bit. Interrupt bit */ 190 /* b5 : d bit. data transfer direction. set to 1 for device to host 191 xfer */ 192 /* b4 : reserved */ 193 /* b3-b0: PM Port */ 194 u8 status; 195 u8 error; 196 u8 lbal; 197 u8 lbam; 198 u8 lbah; 199 u8 device; 200 u8 lbal_exp; 201 u8 lbam_exp; 202 u8 lbah_exp; 203 u8 _r_a; 204 u8 sector_count; 205 u8 sector_count_exp; 206 u8 _r_b; 207 u8 e_status; 208 u8 _r_c[2]; 209 u8 transfer_count; 210 } __attribute__ ((packed)); 211 212 /* 213 * brief the data structure of SATA Completion Response 214 * use to describe the sata task response (64 bytes) 215 */ 216 struct sata_completion_resp { 217 __le32 tag; 218 __le32 status; 219 __le32 param; 220 u32 sata_resp[12]; 221 } __attribute__((packed, aligned(4))); 222 223 224 /* 225 * brief the data structure of SAS HW Event Notification 226 * use to alert the host about the hardware event(64 bytes) 227 */ 228 struct hw_event_resp { 229 __le32 lr_evt_status_phyid_portid; 230 __le32 evt_param; 231 __le32 npip_portstate; 232 struct sas_identify_frame sas_identify; 233 struct dev_to_host_fis sata_fis; 234 } __attribute__((packed, aligned(4))); 235 236 237 /* 238 * brief the data structure of REGISTER DEVICE Command 239 * use to describe MPI REGISTER DEVICE Command (64 bytes) 240 */ 241 242 struct reg_dev_req { 243 __le32 tag; 244 __le32 phyid_portid; 245 __le32 dtype_dlr_retry; 246 __le32 firstburstsize_ITNexustimeout; 247 u8 sas_addr[SAS_ADDR_SIZE]; 248 __le32 upper_device_id; 249 u32 reserved[8]; 250 } __attribute__((packed, aligned(4))); 251 252 253 /* 254 * brief the data structure of DEREGISTER DEVICE Command 255 * use to request spc to remove all internal resources associated 256 * with the device id (64 bytes) 257 */ 258 259 struct dereg_dev_req { 260 __le32 tag; 261 __le32 device_id; 262 u32 reserved[13]; 263 } __attribute__((packed, aligned(4))); 264 265 266 /* 267 * brief the data structure of DEVICE_REGISTRATION Response 268 * use to notify the completion of the device registration (64 bytes) 269 */ 270 271 struct dev_reg_resp { 272 __le32 tag; 273 __le32 status; 274 __le32 device_id; 275 u32 reserved[12]; 276 } __attribute__((packed, aligned(4))); 277 278 279 /* 280 * brief the data structure of Local PHY Control Command 281 * use to issue PHY CONTROL to local phy (64 bytes) 282 */ 283 struct local_phy_ctl_req { 284 __le32 tag; 285 __le32 phyop_phyid; 286 u32 reserved1[13]; 287 } __attribute__((packed, aligned(4))); 288 289 290 /** 291 * brief the data structure of Local Phy Control Response 292 * use to describe MPI Local Phy Control Response (64 bytes) 293 */ 294 struct local_phy_ctl_resp { 295 __le32 tag; 296 __le32 phyop_phyid; 297 __le32 status; 298 u32 reserved[12]; 299 } __attribute__((packed, aligned(4))); 300 301 302 #define OP_BITS 0x0000FF00 303 #define ID_BITS 0x000000FF 304 305 /* 306 * brief the data structure of PORT Control Command 307 * use to control port properties (64 bytes) 308 */ 309 310 struct port_ctl_req { 311 __le32 tag; 312 __le32 portop_portid; 313 __le32 param0; 314 __le32 param1; 315 u32 reserved1[11]; 316 } __attribute__((packed, aligned(4))); 317 318 319 /* 320 * brief the data structure of HW Event Ack Command 321 * use to acknowledge receive HW event (64 bytes) 322 */ 323 324 struct hw_event_ack_req { 325 __le32 tag; 326 __le32 sea_phyid_portid; 327 __le32 param0; 328 __le32 param1; 329 u32 reserved1[11]; 330 } __attribute__((packed, aligned(4))); 331 332 333 /* 334 * brief the data structure of SSP Completion Response 335 * use to indicate a SSP Completion (n bytes) 336 */ 337 struct ssp_completion_resp { 338 __le32 tag; 339 __le32 status; 340 __le32 param; 341 __le32 ssptag_rescv_rescpad; 342 343 /* Must be last --ends in a flexible-array member. */ 344 struct ssp_response_iu ssp_resp_iu; 345 /* __le32 residual_count; */ 346 } __attribute__((packed, aligned(4))); 347 348 349 #define SSP_RESCV_BIT 0x00010000 350 351 /* 352 * brief the data structure of SATA EVNET esponse 353 * use to indicate a SATA Completion (64 bytes) 354 */ 355 356 struct sata_event_resp { 357 __le32 tag; 358 __le32 event; 359 __le32 port_id; 360 __le32 device_id; 361 u32 reserved[11]; 362 } __attribute__((packed, aligned(4))); 363 364 /* 365 * brief the data structure of SSP EVNET esponse 366 * use to indicate a SSP Completion (64 bytes) 367 */ 368 369 struct ssp_event_resp { 370 __le32 tag; 371 __le32 event; 372 __le32 port_id; 373 __le32 device_id; 374 u32 reserved[11]; 375 } __attribute__((packed, aligned(4))); 376 377 /** 378 * brief the data structure of General Event Notification Response 379 * use to describe MPI General Event Notification Response (64 bytes) 380 */ 381 struct general_event_resp { 382 __le32 status; 383 __le32 inb_IOMB_payload[14]; 384 } __attribute__((packed, aligned(4))); 385 386 387 #define GENERAL_EVENT_PAYLOAD 14 388 #define OPCODE_BITS 0x00000fff 389 390 /* 391 * brief the data structure of SMP Request Command 392 * use to describe MPI SMP REQUEST Command (64 bytes) 393 */ 394 struct smp_req { 395 __le32 tag; 396 __le32 device_id; 397 __le32 len_ip_ir; 398 /* Bits [0] - Indirect response */ 399 /* Bits [1] - Indirect Payload */ 400 /* Bits [15:2] - Reserved */ 401 /* Bits [23:16] - direct payload Len */ 402 /* Bits [31:24] - Reserved */ 403 u8 smp_req16[16]; 404 union { 405 u8 smp_req[32]; 406 struct { 407 __le64 long_req_addr;/* sg dma address, LE */ 408 __le32 long_req_size;/* LE */ 409 u32 _r_a; 410 __le64 long_resp_addr;/* sg dma address, LE */ 411 __le32 long_resp_size;/* LE */ 412 u32 _r_b; 413 } long_smp_req;/* sequencer extension */ 414 }; 415 } __attribute__((packed, aligned(4))); 416 /* 417 * brief the data structure of SMP Completion Response 418 * use to describe MPI SMP Completion Response (64 bytes) 419 */ 420 struct smp_completion_resp { 421 __le32 tag; 422 __le32 status; 423 __le32 param; 424 __le32 _r_a[12]; 425 } __attribute__((packed, aligned(4))); 426 427 /* 428 *brief the data structure of SSP SMP SATA Abort Command 429 * use to describe MPI SSP SMP & SATA Abort Command (64 bytes) 430 */ 431 struct task_abort_req { 432 __le32 tag; 433 __le32 device_id; 434 __le32 tag_to_abort; 435 __le32 abort_all; 436 u32 reserved[11]; 437 } __attribute__((packed, aligned(4))); 438 439 /** 440 * brief the data structure of SSP SATA SMP Abort Response 441 * use to describe SSP SMP & SATA Abort Response ( 64 bytes) 442 */ 443 struct task_abort_resp { 444 __le32 tag; 445 __le32 status; 446 __le32 scp; 447 u32 reserved[12]; 448 } __attribute__((packed, aligned(4))); 449 450 451 /** 452 * brief the data structure of SAS Diagnostic Start/End Command 453 * use to describe MPI SAS Diagnostic Start/End Command (64 bytes) 454 */ 455 struct sas_diag_start_end_req { 456 __le32 tag; 457 __le32 operation_phyid; 458 u32 reserved[13]; 459 } __attribute__((packed, aligned(4))); 460 461 462 /** 463 * brief the data structure of SAS Diagnostic Execute Command 464 * use to describe MPI SAS Diagnostic Execute Command (64 bytes) 465 */ 466 struct sas_diag_execute_req{ 467 __le32 tag; 468 __le32 cmdtype_cmddesc_phyid; 469 __le32 pat1_pat2; 470 __le32 threshold; 471 __le32 codepat_errmsk; 472 __le32 pmon; 473 __le32 pERF1CTL; 474 u32 reserved[8]; 475 } __attribute__((packed, aligned(4))); 476 477 478 #define SAS_DIAG_PARAM_BYTES 24 479 480 /* 481 * brief the data structure of Set Device State Command 482 * use to describe MPI Set Device State Command (64 bytes) 483 */ 484 struct set_dev_state_req { 485 __le32 tag; 486 __le32 device_id; 487 __le32 nds; 488 u32 reserved[12]; 489 } __attribute__((packed, aligned(4))); 490 491 /* 492 * brief the data structure of sas_re_initialization 493 */ 494 struct sas_re_initialization_req { 495 496 __le32 tag; 497 __le32 SSAHOLT;/* bit29-set max port; 498 ** bit28-set open reject cmd retries. 499 ** bit27-set open reject data retries. 500 ** bit26-set open reject option, remap:1 or not:0. 501 ** bit25-set sata head of line time out. 502 */ 503 __le32 reserved_maxPorts; 504 __le32 open_reject_cmdretries_data_retries;/* cmd retries: 31-bit16; 505 * data retries: bit15-bit0. 506 */ 507 __le32 sata_hol_tmo; 508 u32 reserved1[10]; 509 } __attribute__((packed, aligned(4))); 510 511 /* 512 * brief the data structure of SATA Start Command 513 * use to describe MPI SATA IO Start Command (64 bytes) 514 */ 515 516 struct sata_start_req { 517 __le32 tag; 518 __le32 device_id; 519 __le32 data_len; 520 __le32 retfis_ncqtag_atap_dir_m; 521 struct host_to_dev_fis sata_fis; 522 u32 reserved1; 523 u32 reserved2; 524 u32 addr_low; 525 u32 addr_high; 526 __le32 len; 527 __le32 esgl; 528 } __attribute__((packed, aligned(4))); 529 530 /** 531 * brief the data structure of SSP INI TM Start Command 532 * use to describe MPI SSP INI TM Start Command (64 bytes) 533 */ 534 struct ssp_ini_tm_start_req { 535 __le32 tag; 536 __le32 device_id; 537 __le32 relate_tag; 538 __le32 tmf; 539 u8 lun[8]; 540 __le32 ds_ads_m; 541 u32 reserved[8]; 542 } __attribute__((packed, aligned(4))); 543 544 545 struct ssp_info_unit { 546 u8 lun[8];/* SCSI Logical Unit Number */ 547 u8 reserved1;/* reserved */ 548 u8 efb_prio_attr; 549 /* B7 : enabledFirstBurst */ 550 /* B6-3 : taskPriority */ 551 /* B2-0 : taskAttribute */ 552 u8 reserved2; /* reserved */ 553 u8 additional_cdb_len; 554 /* B7-2 : additional_cdb_len */ 555 /* B1-0 : reserved */ 556 u8 cdb[16];/* The SCSI CDB up to 16 bytes length */ 557 } __attribute__((packed, aligned(4))); 558 559 560 /** 561 * brief the data structure of SSP INI IO Start Command 562 * use to describe MPI SSP INI IO Start Command (64 bytes) 563 */ 564 struct ssp_ini_io_start_req { 565 __le32 tag; 566 __le32 device_id; 567 __le32 data_len; 568 __le32 dir_m_tlr; 569 struct ssp_info_unit ssp_iu; 570 __le32 addr_low; 571 __le32 addr_high; 572 __le32 len; 573 __le32 esgl; 574 } __attribute__((packed, aligned(4))); 575 576 577 /** 578 * brief the data structure of Firmware download 579 * use to describe MPI FW DOWNLOAD Command (64 bytes) 580 */ 581 struct fw_flash_Update_req { 582 __le32 tag; 583 __le32 cur_image_offset; 584 __le32 cur_image_len; 585 __le32 total_image_len; 586 u32 reserved0[7]; 587 __le32 sgl_addr_lo; 588 __le32 sgl_addr_hi; 589 __le32 len; 590 __le32 ext_reserved; 591 } __attribute__((packed, aligned(4))); 592 593 594 #define FWFLASH_IOMB_RESERVED_LEN 0x07 595 /** 596 * brief the data structure of FW_FLASH_UPDATE Response 597 * use to describe MPI FW_FLASH_UPDATE Response (64 bytes) 598 * 599 */ 600 struct fw_flash_Update_resp { 601 __le32 tag; 602 __le32 status; 603 u32 reserved[13]; 604 } __attribute__((packed, aligned(4))); 605 606 607 /** 608 * brief the data structure of Get NVM Data Command 609 * use to get data from NVM in HBA(64 bytes) 610 */ 611 struct get_nvm_data_req { 612 __le32 tag; 613 __le32 len_ir_vpdd; 614 __le32 vpd_offset; 615 u32 reserved[8]; 616 __le32 resp_addr_lo; 617 __le32 resp_addr_hi; 618 __le32 resp_len; 619 u32 reserved1; 620 } __attribute__((packed, aligned(4))); 621 622 623 struct set_nvm_data_req { 624 __le32 tag; 625 __le32 len_ir_vpdd; 626 __le32 vpd_offset; 627 __le32 reserved[8]; 628 __le32 resp_addr_lo; 629 __le32 resp_addr_hi; 630 __le32 resp_len; 631 u32 reserved1; 632 } __attribute__((packed, aligned(4))); 633 634 635 #define TWI_DEVICE 0x0 636 #define C_SEEPROM 0x1 637 #define VPD_FLASH 0x4 638 #define AAP1_RDUMP 0x5 639 #define IOP_RDUMP 0x6 640 #define EXPAN_ROM 0x7 641 642 #define IPMode 0x80000000 643 #define NVMD_TYPE 0x0000000F 644 #define NVMD_STAT 0x0000FFFF 645 #define NVMD_LEN 0xFF000000 646 /** 647 * brief the data structure of Get NVMD Data Response 648 * use to describe MPI Get NVMD Data Response (64 bytes) 649 */ 650 struct get_nvm_data_resp { 651 __le32 tag; 652 __le32 ir_tda_bn_dps_das_nvm; 653 __le32 dlen_status; 654 __le32 nvm_data[12]; 655 } __attribute__((packed, aligned(4))); 656 657 658 /** 659 * brief the data structure of SAS Diagnostic Start/End Response 660 * use to describe MPI SAS Diagnostic Start/End Response (64 bytes) 661 * 662 */ 663 struct sas_diag_start_end_resp { 664 __le32 tag; 665 __le32 status; 666 u32 reserved[13]; 667 } __attribute__((packed, aligned(4))); 668 669 670 /** 671 * brief the data structure of SAS Diagnostic Execute Response 672 * use to describe MPI SAS Diagnostic Execute Response (64 bytes) 673 * 674 */ 675 struct sas_diag_execute_resp { 676 __le32 tag; 677 __le32 cmdtype_cmddesc_phyid; 678 __le32 Status; 679 __le32 ReportData; 680 u32 reserved[11]; 681 } __attribute__((packed, aligned(4))); 682 683 684 /** 685 * brief the data structure of Set Device State Response 686 * use to describe MPI Set Device State Response (64 bytes) 687 * 688 */ 689 struct set_dev_state_resp { 690 __le32 tag; 691 __le32 status; 692 __le32 device_id; 693 __le32 pds_nds; 694 u32 reserved[11]; 695 } __attribute__((packed, aligned(4))); 696 697 698 #define NDS_BITS 0x0F 699 #define PDS_BITS 0xF0 700 701 /* 702 * HW Events type 703 */ 704 705 #define HW_EVENT_RESET_START 0x01 706 #define HW_EVENT_CHIP_RESET_COMPLETE 0x02 707 #define HW_EVENT_PHY_STOP_STATUS 0x03 708 #define HW_EVENT_SAS_PHY_UP 0x04 709 #define HW_EVENT_SATA_PHY_UP 0x05 710 #define HW_EVENT_SATA_SPINUP_HOLD 0x06 711 #define HW_EVENT_PHY_DOWN 0x07 712 #define HW_EVENT_PORT_INVALID 0x08 713 #define HW_EVENT_BROADCAST_CHANGE 0x09 714 #define HW_EVENT_PHY_ERROR 0x0A 715 #define HW_EVENT_BROADCAST_SES 0x0B 716 #define HW_EVENT_INBOUND_CRC_ERROR 0x0C 717 #define HW_EVENT_HARD_RESET_RECEIVED 0x0D 718 #define HW_EVENT_MALFUNCTION 0x0E 719 #define HW_EVENT_ID_FRAME_TIMEOUT 0x0F 720 #define HW_EVENT_BROADCAST_EXP 0x10 721 #define HW_EVENT_PHY_START_STATUS 0x11 722 #define HW_EVENT_LINK_ERR_INVALID_DWORD 0x12 723 #define HW_EVENT_LINK_ERR_DISPARITY_ERROR 0x13 724 #define HW_EVENT_LINK_ERR_CODE_VIOLATION 0x14 725 #define HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH 0x15 726 #define HW_EVENT_LINK_ERR_PHY_RESET_FAILED 0x16 727 #define HW_EVENT_PORT_RECOVERY_TIMER_TMO 0x17 728 #define HW_EVENT_PORT_RECOVER 0x18 729 #define HW_EVENT_PORT_RESET_TIMER_TMO 0x19 730 #define HW_EVENT_PORT_RESET_COMPLETE 0x20 731 #define EVENT_BROADCAST_ASYNCH_EVENT 0x21 732 733 /* port state */ 734 #define PORT_NOT_ESTABLISHED 0x00 735 #define PORT_VALID 0x01 736 #define PORT_LOSTCOMM 0x02 737 #define PORT_IN_RESET 0x04 738 #define PORT_INVALID 0x08 739 740 /* 741 * SSP/SMP/SATA IO Completion Status values 742 */ 743 744 #define IO_SUCCESS 0x00 745 #define IO_ABORTED 0x01 746 #define IO_OVERFLOW 0x02 747 #define IO_UNDERFLOW 0x03 748 #define IO_FAILED 0x04 749 #define IO_ABORT_RESET 0x05 750 #define IO_NOT_VALID 0x06 751 #define IO_NO_DEVICE 0x07 752 #define IO_ILLEGAL_PARAMETER 0x08 753 #define IO_LINK_FAILURE 0x09 754 #define IO_PROG_ERROR 0x0A 755 #define IO_EDC_IN_ERROR 0x0B 756 #define IO_EDC_OUT_ERROR 0x0C 757 #define IO_ERROR_HW_TIMEOUT 0x0D 758 #define IO_XFER_ERROR_BREAK 0x0E 759 #define IO_XFER_ERROR_PHY_NOT_READY 0x0F 760 #define IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED 0x10 761 #define IO_OPEN_CNX_ERROR_ZONE_VIOLATION 0x11 762 #define IO_OPEN_CNX_ERROR_BREAK 0x12 763 #define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS 0x13 764 #define IO_OPEN_CNX_ERROR_BAD_DESTINATION 0x14 765 #define IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED 0x15 766 #define IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY 0x16 767 #define IO_OPEN_CNX_ERROR_WRONG_DESTINATION 0x17 768 #define IO_OPEN_CNX_ERROR_UNKNOWN_ERROR 0x18 769 #define IO_XFER_ERROR_NAK_RECEIVED 0x19 770 #define IO_XFER_ERROR_ACK_NAK_TIMEOUT 0x1A 771 #define IO_XFER_ERROR_PEER_ABORTED 0x1B 772 #define IO_XFER_ERROR_RX_FRAME 0x1C 773 #define IO_XFER_ERROR_DMA 0x1D 774 #define IO_XFER_ERROR_CREDIT_TIMEOUT 0x1E 775 #define IO_XFER_ERROR_SATA_LINK_TIMEOUT 0x1F 776 #define IO_XFER_ERROR_SATA 0x20 777 #define IO_XFER_ERROR_ABORTED_DUE_TO_SRST 0x22 778 #define IO_XFER_ERROR_REJECTED_NCQ_MODE 0x21 779 #define IO_XFER_ERROR_ABORTED_NCQ_MODE 0x23 780 #define IO_XFER_OPEN_RETRY_TIMEOUT 0x24 781 #define IO_XFER_SMP_RESP_CONNECTION_ERROR 0x25 782 #define IO_XFER_ERROR_UNEXPECTED_PHASE 0x26 783 #define IO_XFER_ERROR_XFER_RDY_OVERRUN 0x27 784 #define IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED 0x28 785 786 #define IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT 0x30 787 #define IO_XFER_ERROR_CMD_ISSUE_BREAK_BEFORE_ACK_NAK 0x31 788 #define IO_XFER_ERROR_CMD_ISSUE_PHY_DOWN_BEFORE_ACK_NAK 0x32 789 790 #define IO_XFER_ERROR_OFFSET_MISMATCH 0x34 791 #define IO_XFER_ERROR_XFER_ZERO_DATA_LEN 0x35 792 #define IO_XFER_CMD_FRAME_ISSUED 0x36 793 #define IO_ERROR_INTERNAL_SMP_RESOURCE 0x37 794 #define IO_PORT_IN_RESET 0x38 795 #define IO_DS_NON_OPERATIONAL 0x39 796 #define IO_DS_IN_RECOVERY 0x3A 797 #define IO_TM_TAG_NOT_FOUND 0x3B 798 #define IO_XFER_PIO_SETUP_ERROR 0x3C 799 #define IO_SSP_EXT_IU_ZERO_LEN_ERROR 0x3D 800 #define IO_DS_IN_ERROR 0x3E 801 #define IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY 0x3F 802 #define IO_ABORT_IN_PROGRESS 0x40 803 #define IO_ABORT_DELAYED 0x41 804 #define IO_INVALID_LENGTH 0x42 805 #define IO_FATAL_ERROR 0x51 806 807 /* WARNING: This error code must always be the last number. 808 * If you add error code, modify this code also 809 * It is used as an index 810 */ 811 #define IO_ERROR_UNKNOWN_GENERIC 0x43 812 813 /* MSGU CONFIGURATION TABLE*/ 814 815 #define SPC_MSGU_CFG_TABLE_UPDATE 0x01/* Inbound doorbell bit0 */ 816 #define SPC_MSGU_CFG_TABLE_RESET 0x02/* Inbound doorbell bit1 */ 817 #define SPC_MSGU_CFG_TABLE_FREEZE 0x04/* Inbound doorbell bit2 */ 818 #define SPC_MSGU_CFG_TABLE_UNFREEZE 0x08/* Inbound doorbell bit4 */ 819 #define MSGU_IBDB_SET 0x04 820 #define MSGU_HOST_INT_STATUS 0x08 821 #define MSGU_HOST_INT_MASK 0x0C 822 #define MSGU_IOPIB_INT_STATUS 0x18 823 #define MSGU_IOPIB_INT_MASK 0x1C 824 #define MSGU_IBDB_CLEAR 0x20/* RevB - Host not use */ 825 #define MSGU_MSGU_CONTROL 0x24 826 #define MSGU_ODR 0x3C/* RevB */ 827 #define MSGU_ODCR 0x40/* RevB */ 828 #define MSGU_SCRATCH_PAD_0 0x44 829 #define MSGU_SCRATCH_PAD_1 0x48 830 #define MSGU_SCRATCH_PAD_2 0x4C 831 #define MSGU_SCRATCH_PAD_3 0x50 832 #define MSGU_HOST_SCRATCH_PAD_0 0x54 833 #define MSGU_HOST_SCRATCH_PAD_1 0x58 834 #define MSGU_HOST_SCRATCH_PAD_2 0x5C 835 #define MSGU_HOST_SCRATCH_PAD_3 0x60 836 #define MSGU_HOST_SCRATCH_PAD_4 0x64 837 #define MSGU_HOST_SCRATCH_PAD_5 0x68 838 #define MSGU_HOST_SCRATCH_PAD_6 0x6C 839 #define MSGU_HOST_SCRATCH_PAD_7 0x70 840 #define MSGU_ODMR 0x74/* RevB */ 841 842 /* bit definition for ODMR register */ 843 #define ODMR_MASK_ALL 0xFFFFFFFF/* mask all 844 interrupt vector */ 845 #define ODMR_CLEAR_ALL 0/* clear all 846 interrupt vector */ 847 /* bit definition for ODCR register */ 848 #define ODCR_CLEAR_ALL 0xFFFFFFFF /* mask all 849 interrupt vector*/ 850 /* MSIX Interupts */ 851 #define MSIX_TABLE_OFFSET 0x2000 852 #define MSIX_TABLE_ELEMENT_SIZE 0x10 853 #define MSIX_INTERRUPT_CONTROL_OFFSET 0xC 854 #define MSIX_TABLE_BASE (MSIX_TABLE_OFFSET + MSIX_INTERRUPT_CONTROL_OFFSET) 855 #define MSIX_INTERRUPT_DISABLE 0x1 856 #define MSIX_INTERRUPT_ENABLE 0x0 857 858 859 /* state definition for Scratch Pad1 register */ 860 #define SCRATCH_PAD1_POR 0x00 /* power on reset state */ 861 #define SCRATCH_PAD1_SFR 0x01 /* soft reset state */ 862 #define SCRATCH_PAD1_ERR 0x02 /* error state */ 863 #define SCRATCH_PAD1_RDY 0x03 /* ready state */ 864 #define SCRATCH_PAD1_RST 0x04 /* soft reset toggle flag */ 865 #define SCRATCH_PAD1_AAP1RDY_RST 0x08 /* AAP1 ready for soft reset */ 866 #define SCRATCH_PAD1_STATE_MASK 0xFFFFFFF0 /* ScratchPad1 867 Mask, bit1-0 State, bit2 Soft Reset, bit3 FW RDY for Soft Reset */ 868 #define SCRATCH_PAD1_RESERVED 0x000003F8 /* Scratch Pad1 869 Reserved bit 3 to 9 */ 870 871 /* state definition for Scratch Pad2 register */ 872 #define SCRATCH_PAD2_POR 0x00 /* power on state */ 873 #define SCRATCH_PAD2_SFR 0x01 /* soft reset state */ 874 #define SCRATCH_PAD2_ERR 0x02 /* error state */ 875 #define SCRATCH_PAD2_RDY 0x03 /* ready state */ 876 #define SCRATCH_PAD2_FWRDY_RST 0x04 /* FW ready for soft reset flag*/ 877 #define SCRATCH_PAD2_IOPRDY_RST 0x08 /* IOP ready for soft reset */ 878 #define SCRATCH_PAD2_STATE_MASK 0xFFFFFFF4 /* ScratchPad 2 879 Mask, bit1-0 State */ 880 #define SCRATCH_PAD2_RESERVED 0x000003FC /* Scratch Pad1 881 Reserved bit 2 to 9 */ 882 883 #define SCRATCH_PAD_ERROR_MASK 0xFFFFFC00 /* Error mask bits */ 884 #define SCRATCH_PAD_STATE_MASK 0x00000003 /* State Mask bits */ 885 886 /* main configuration offset - byte offset */ 887 #define MAIN_SIGNATURE_OFFSET 0x00/* DWORD 0x00 */ 888 #define MAIN_INTERFACE_REVISION 0x04/* DWORD 0x01 */ 889 #define MAIN_FW_REVISION 0x08/* DWORD 0x02 */ 890 #define MAIN_MAX_OUTSTANDING_IO_OFFSET 0x0C/* DWORD 0x03 */ 891 #define MAIN_MAX_SGL_OFFSET 0x10/* DWORD 0x04 */ 892 #define MAIN_CNTRL_CAP_OFFSET 0x14/* DWORD 0x05 */ 893 #define MAIN_GST_OFFSET 0x18/* DWORD 0x06 */ 894 #define MAIN_IBQ_OFFSET 0x1C/* DWORD 0x07 */ 895 #define MAIN_OBQ_OFFSET 0x20/* DWORD 0x08 */ 896 #define MAIN_IQNPPD_HPPD_OFFSET 0x24/* DWORD 0x09 */ 897 #define MAIN_OB_HW_EVENT_PID03_OFFSET 0x28/* DWORD 0x0A */ 898 #define MAIN_OB_HW_EVENT_PID47_OFFSET 0x2C/* DWORD 0x0B */ 899 #define MAIN_OB_NCQ_EVENT_PID03_OFFSET 0x30/* DWORD 0x0C */ 900 #define MAIN_OB_NCQ_EVENT_PID47_OFFSET 0x34/* DWORD 0x0D */ 901 #define MAIN_TITNX_EVENT_PID03_OFFSET 0x38/* DWORD 0x0E */ 902 #define MAIN_TITNX_EVENT_PID47_OFFSET 0x3C/* DWORD 0x0F */ 903 #define MAIN_OB_SSP_EVENT_PID03_OFFSET 0x40/* DWORD 0x10 */ 904 #define MAIN_OB_SSP_EVENT_PID47_OFFSET 0x44/* DWORD 0x11 */ 905 #define MAIN_OB_SMP_EVENT_PID03_OFFSET 0x48/* DWORD 0x12 */ 906 #define MAIN_OB_SMP_EVENT_PID47_OFFSET 0x4C/* DWORD 0x13 */ 907 #define MAIN_EVENT_LOG_ADDR_HI 0x50/* DWORD 0x14 */ 908 #define MAIN_EVENT_LOG_ADDR_LO 0x54/* DWORD 0x15 */ 909 #define MAIN_EVENT_LOG_BUFF_SIZE 0x58/* DWORD 0x16 */ 910 #define MAIN_EVENT_LOG_OPTION 0x5C/* DWORD 0x17 */ 911 #define MAIN_IOP_EVENT_LOG_ADDR_HI 0x60/* DWORD 0x18 */ 912 #define MAIN_IOP_EVENT_LOG_ADDR_LO 0x64/* DWORD 0x19 */ 913 #define MAIN_IOP_EVENT_LOG_BUFF_SIZE 0x68/* DWORD 0x1A */ 914 #define MAIN_IOP_EVENT_LOG_OPTION 0x6C/* DWORD 0x1B */ 915 #define MAIN_FATAL_ERROR_INTERRUPT 0x70/* DWORD 0x1C */ 916 #define MAIN_FATAL_ERROR_RDUMP0_OFFSET 0x74/* DWORD 0x1D */ 917 #define MAIN_FATAL_ERROR_RDUMP0_LENGTH 0x78/* DWORD 0x1E */ 918 #define MAIN_FATAL_ERROR_RDUMP1_OFFSET 0x7C/* DWORD 0x1F */ 919 #define MAIN_FATAL_ERROR_RDUMP1_LENGTH 0x80/* DWORD 0x20 */ 920 #define MAIN_HDA_FLAGS_OFFSET 0x84/* DWORD 0x21 */ 921 #define MAIN_ANALOG_SETUP_OFFSET 0x88/* DWORD 0x22 */ 922 923 /* Gereral Status Table offset - byte offset */ 924 #define GST_GSTLEN_MPIS_OFFSET 0x00 925 #define GST_IQ_FREEZE_STATE0_OFFSET 0x04 926 #define GST_IQ_FREEZE_STATE1_OFFSET 0x08 927 #define GST_MSGUTCNT_OFFSET 0x0C 928 #define GST_IOPTCNT_OFFSET 0x10 929 #define GST_PHYSTATE_OFFSET 0x18 930 #define GST_PHYSTATE0_OFFSET 0x18 931 #define GST_PHYSTATE1_OFFSET 0x1C 932 #define GST_PHYSTATE2_OFFSET 0x20 933 #define GST_PHYSTATE3_OFFSET 0x24 934 #define GST_PHYSTATE4_OFFSET 0x28 935 #define GST_PHYSTATE5_OFFSET 0x2C 936 #define GST_PHYSTATE6_OFFSET 0x30 937 #define GST_PHYSTATE7_OFFSET 0x34 938 #define GST_RERRINFO_OFFSET 0x44 939 940 /* General Status Table - MPI state */ 941 #define GST_MPI_STATE_UNINIT 0x00 942 #define GST_MPI_STATE_INIT 0x01 943 #define GST_MPI_STATE_TERMINATION 0x02 944 #define GST_MPI_STATE_ERROR 0x03 945 #define GST_MPI_STATE_MASK 0x07 946 947 #define MBIC_NMI_ENABLE_VPE0_IOP 0x000418 948 #define MBIC_NMI_ENABLE_VPE0_AAP1 0x000418 949 /* PCIE registers - BAR2(0x18), BAR1(win) 0x010000 */ 950 #define PCIE_EVENT_INTERRUPT_ENABLE 0x003040 951 #define PCIE_EVENT_INTERRUPT 0x003044 952 #define PCIE_ERROR_INTERRUPT_ENABLE 0x003048 953 #define PCIE_ERROR_INTERRUPT 0x00304C 954 /* signature definition for host scratch pad0 register */ 955 #define SPC_SOFT_RESET_SIGNATURE 0x252acbcd 956 /* Signature for Soft Reset */ 957 958 /* SPC Reset register - BAR4(0x20), BAR2(win) (need dynamic mapping) */ 959 #define SPC_REG_RESET 0x000000/* reset register */ 960 961 /* bit difination for SPC_RESET register */ 962 #define SPC_REG_RESET_OSSP 0x00000001 963 #define SPC_REG_RESET_RAAE 0x00000002 964 #define SPC_REG_RESET_PCS_SPBC 0x00000004 965 #define SPC_REG_RESET_PCS_IOP_SS 0x00000008 966 #define SPC_REG_RESET_PCS_AAP1_SS 0x00000010 967 #define SPC_REG_RESET_PCS_AAP2_SS 0x00000020 968 #define SPC_REG_RESET_PCS_LM 0x00000040 969 #define SPC_REG_RESET_PCS 0x00000080 970 #define SPC_REG_RESET_GSM 0x00000100 971 #define SPC_REG_RESET_DDR2 0x00010000 972 #define SPC_REG_RESET_BDMA_CORE 0x00020000 973 #define SPC_REG_RESET_BDMA_SXCBI 0x00040000 974 #define SPC_REG_RESET_PCIE_AL_SXCBI 0x00080000 975 #define SPC_REG_RESET_PCIE_PWR 0x00100000 976 #define SPC_REG_RESET_PCIE_SFT 0x00200000 977 #define SPC_REG_RESET_PCS_SXCBI 0x00400000 978 #define SPC_REG_RESET_LMS_SXCBI 0x00800000 979 #define SPC_REG_RESET_PMIC_SXCBI 0x01000000 980 #define SPC_REG_RESET_PMIC_CORE 0x02000000 981 #define SPC_REG_RESET_PCIE_PC_SXCBI 0x04000000 982 #define SPC_REG_RESET_DEVICE 0x80000000 983 984 /* registers for BAR Shifting - BAR2(0x18), BAR1(win) */ 985 #define SPC_IBW_AXI_TRANSLATION_LOW 0x003258 986 987 #define MBIC_AAP1_ADDR_BASE 0x060000 988 #define MBIC_IOP_ADDR_BASE 0x070000 989 #define GSM_ADDR_BASE 0x0700000 990 /* Dynamic map through Bar4 - 0x00700000 */ 991 #define GSM_CONFIG_RESET 0x00000000 992 #define RAM_ECC_DB_ERR 0x00000018 993 #define GSM_READ_ADDR_PARITY_INDIC 0x00000058 994 #define GSM_WRITE_ADDR_PARITY_INDIC 0x00000060 995 #define GSM_WRITE_DATA_PARITY_INDIC 0x00000068 996 #define GSM_READ_ADDR_PARITY_CHECK 0x00000038 997 #define GSM_WRITE_ADDR_PARITY_CHECK 0x00000040 998 #define GSM_WRITE_DATA_PARITY_CHECK 0x00000048 999 1000 #define RB6_ACCESS_REG 0x6A0000 1001 #define HDAC_EXEC_CMD 0x0002 1002 #define HDA_C_PA 0xcb 1003 #define HDA_SEQ_ID_BITS 0x00ff0000 1004 #define HDA_GSM_OFFSET_BITS 0x00FFFFFF 1005 #define MBIC_AAP1_ADDR_BASE 0x060000 1006 #define MBIC_IOP_ADDR_BASE 0x070000 1007 #define GSM_ADDR_BASE 0x0700000 1008 #define SPC_TOP_LEVEL_ADDR_BASE 0x000000 1009 #define GSM_CONFIG_RESET_VALUE 0x00003b00 1010 #define GPIO_ADDR_BASE 0x00090000 1011 #define GPIO_GPIO_0_0UTPUT_CTL_OFFSET 0x0000010c 1012 1013 /* RB6 offset */ 1014 #define SPC_RB6_OFFSET 0x80C0 1015 /* Magic number of soft reset for RB6 */ 1016 #define RB6_MAGIC_NUMBER_RST 0x1234 1017 1018 /* Device Register status */ 1019 #define DEVREG_SUCCESS 0x00 1020 #define DEVREG_FAILURE_OUT_OF_RESOURCE 0x01 1021 #define DEVREG_FAILURE_DEVICE_ALREADY_REGISTERED 0x02 1022 #define DEVREG_FAILURE_INVALID_PHY_ID 0x03 1023 #define DEVREG_FAILURE_PHY_ID_ALREADY_REGISTERED 0x04 1024 #define DEVREG_FAILURE_PORT_ID_OUT_OF_RANGE 0x05 1025 #define DEVREG_FAILURE_PORT_NOT_VALID_STATE 0x06 1026 #define DEVREG_FAILURE_DEVICE_TYPE_NOT_VALID 0x07 1027 1028 #define GSM_BASE 0x4F0000 1029 #define SHIFT_REG_64K_MASK 0xffff0000 1030 #define SHIFT_REG_BIT_SHIFT 8 1031 #endif 1032 1033