1 /* SPDX-License-Identifier: GPL-2.0 */ 2 /* esp_scsi.h: Defines and structures for the ESP driver. 3 * 4 * Copyright (C) 2007 David S. Miller (davem@davemloft.net) 5 */ 6 7 #ifndef _ESP_SCSI_H 8 #define _ESP_SCSI_H 9 10 /* Access Description Offset */ 11 #define ESP_TCLOW 0x00UL /* rw Low bits transfer count 0x00 */ 12 #define ESP_TCMED 0x01UL /* rw Mid bits transfer count 0x04 */ 13 #define ESP_FDATA 0x02UL /* rw FIFO data bits 0x08 */ 14 #define ESP_CMD 0x03UL /* rw SCSI command bits 0x0c */ 15 #define ESP_STATUS 0x04UL /* ro ESP status register 0x10 */ 16 #define ESP_BUSID ESP_STATUS /* wo BusID for sel/resel 0x10 */ 17 #define ESP_INTRPT 0x05UL /* ro Kind of interrupt 0x14 */ 18 #define ESP_TIMEO ESP_INTRPT /* wo Timeout for sel/resel 0x14 */ 19 #define ESP_SSTEP 0x06UL /* ro Sequence step register 0x18 */ 20 #define ESP_STP ESP_SSTEP /* wo Transfer period/sync 0x18 */ 21 #define ESP_FFLAGS 0x07UL /* ro Bits current FIFO info 0x1c */ 22 #define ESP_SOFF ESP_FFLAGS /* wo Sync offset 0x1c */ 23 #define ESP_CFG1 0x08UL /* rw First cfg register 0x20 */ 24 #define ESP_CFACT 0x09UL /* wo Clock conv factor 0x24 */ 25 #define ESP_STATUS2 ESP_CFACT /* ro HME status2 register 0x24 */ 26 #define ESP_CTEST 0x0aUL /* wo Chip test register 0x28 */ 27 #define ESP_CFG2 0x0bUL /* rw Second cfg register 0x2c */ 28 #define ESP_CFG3 0x0cUL /* rw Third cfg register 0x30 */ 29 #define ESP_CFG4 0x0dUL /* rw Fourth cfg register 0x34 */ 30 #define ESP_TCHI 0x0eUL /* rw High bits transf count 0x38 */ 31 #define ESP_UID ESP_TCHI /* ro Unique ID code 0x38 */ 32 #define FAS_RLO ESP_TCHI /* rw HME extended counter 0x38 */ 33 #define ESP_FGRND 0x0fUL /* rw Data base for fifo 0x3c */ 34 #define FAS_RHI ESP_FGRND /* rw HME extended counter 0x3c */ 35 36 #define SBUS_ESP_REG_SIZE 0x40UL 37 38 /* Bitfield meanings for the above registers. */ 39 40 /* ESP config reg 1, read-write, found on all ESP chips */ 41 #define ESP_CONFIG1_ID 0x07 /* My BUS ID bits */ 42 #define ESP_CONFIG1_CHTEST 0x08 /* Enable ESP chip tests */ 43 #define ESP_CONFIG1_PENABLE 0x10 /* Enable parity checks */ 44 #define ESP_CONFIG1_PARTEST 0x20 /* Parity test mode enabled? */ 45 #define ESP_CONFIG1_SRRDISAB 0x40 /* Disable SCSI reset reports */ 46 #define ESP_CONFIG1_SLCABLE 0x80 /* Enable slow cable mode */ 47 48 /* ESP config reg 2, read-write, found only on esp100a+esp200+esp236 chips */ 49 #define ESP_CONFIG2_DMAPARITY 0x01 /* enable DMA Parity (200,236) */ 50 #define ESP_CONFIG2_REGPARITY 0x02 /* enable reg Parity (200,236) */ 51 #define ESP_CONFIG2_BADPARITY 0x04 /* Bad parity target abort */ 52 #define ESP_CONFIG2_SCSI2ENAB 0x08 /* Enable SCSI-2 features (tgtmode) */ 53 #define ESP_CONFIG2_HI 0x10 /* High Impedance DREQ ??? */ 54 #define ESP_CONFIG2_HMEFENAB 0x10 /* HME features enable */ 55 #define ESP_CONFIG2_BCM 0x20 /* Enable byte-ctrl (236) */ 56 #define ESP_CONFIG2_DISPINT 0x20 /* Disable pause irq (hme) */ 57 #define ESP_CONFIG2_FENAB 0x40 /* Enable features (fas100,216) */ 58 #define ESP_CONFIG2_SPL 0x40 /* Enable status-phase latch (236) */ 59 #define ESP_CONFIG2_MKDONE 0x40 /* HME magic feature */ 60 #define ESP_CONFIG2_HME32 0x80 /* HME 32 extended */ 61 #define ESP_CONFIG2_MAGIC 0xe0 /* Invalid bits... */ 62 63 /* ESP config register 3 read-write, found only esp236+fas236+fas100a+hme chips */ 64 #define ESP_CONFIG3_FCLOCK 0x01 /* FAST SCSI clock rate (esp100a/hme) */ 65 #define ESP_CONFIG3_TEM 0x01 /* Enable thresh-8 mode (esp/fas236) */ 66 #define ESP_CONFIG3_FAST 0x02 /* Enable FAST SCSI (esp100a/hme) */ 67 #define ESP_CONFIG3_ADMA 0x02 /* Enable alternate-dma (esp/fas236) */ 68 #define ESP_CONFIG3_TENB 0x04 /* group2 SCSI2 support (esp100a/hme) */ 69 #define ESP_CONFIG3_SRB 0x04 /* Save residual byte (esp/fas236) */ 70 #define ESP_CONFIG3_TMS 0x08 /* Three-byte msg's ok (esp100a/hme) */ 71 #define ESP_CONFIG3_FCLK 0x08 /* Fast SCSI clock rate (esp/fas236) */ 72 #define ESP_CONFIG3_IDMSG 0x10 /* ID message checking (esp100a/hme) */ 73 #define ESP_CONFIG3_FSCSI 0x10 /* Enable FAST SCSI (esp/fas236) */ 74 #define ESP_CONFIG3_GTM 0x20 /* group2 SCSI2 support (esp/fas236) */ 75 #define ESP_CONFIG3_IDBIT3 0x20 /* Bit 3 of HME SCSI-ID (hme) */ 76 #define ESP_CONFIG3_TBMS 0x40 /* Three-byte msg's ok (esp/fas236) */ 77 #define ESP_CONFIG3_EWIDE 0x40 /* Enable Wide-SCSI (hme) */ 78 #define ESP_CONFIG3_IMS 0x80 /* ID msg chk'ng (esp/fas236) */ 79 #define ESP_CONFIG3_OBPUSH 0x80 /* Push odd-byte to dma (hme) */ 80 81 /* ESP config register 4 read-write */ 82 #define ESP_CONFIG4_BBTE 0x01 /* Back-to-back transfers (fsc) */ 83 #define ESP_CONGIG4_TEST 0x02 /* Transfer counter test mode (fsc) */ 84 #define ESP_CONFIG4_RADE 0x04 /* Active negation (am53c974/fsc) */ 85 #define ESP_CONFIG4_RAE 0x08 /* Act. negation REQ/ACK (am53c974) */ 86 #define ESP_CONFIG4_PWD 0x20 /* Reduced power feature (am53c974) */ 87 #define ESP_CONFIG4_GE0 0x40 /* Glitch eater bit 0 (am53c974) */ 88 #define ESP_CONFIG4_GE1 0x80 /* Glitch eater bit 1 (am53c974) */ 89 90 #define ESP_CONFIG_GE_12NS (0) 91 #define ESP_CONFIG_GE_25NS (ESP_CONFIG_GE1) 92 #define ESP_CONFIG_GE_35NS (ESP_CONFIG_GE0) 93 #define ESP_CONFIG_GE_0NS (ESP_CONFIG_GE0 | ESP_CONFIG_GE1) 94 95 /* ESP command register read-write */ 96 /* Group 1 commands: These may be sent at any point in time to the ESP 97 * chip. None of them can generate interrupts 'cept 98 * the "SCSI bus reset" command if you have not disabled 99 * SCSI reset interrupts in the config1 ESP register. 100 */ 101 #define ESP_CMD_NULL 0x00 /* Null command, ie. a nop */ 102 #define ESP_CMD_FLUSH 0x01 /* FIFO Flush */ 103 #define ESP_CMD_RC 0x02 /* Chip reset */ 104 #define ESP_CMD_RS 0x03 /* SCSI bus reset */ 105 106 /* Group 2 commands: ESP must be an initiator and connected to a target 107 * for these commands to work. 108 */ 109 #define ESP_CMD_TI 0x10 /* Transfer Information */ 110 #define ESP_CMD_ICCSEQ 0x11 /* Initiator cmd complete sequence */ 111 #define ESP_CMD_MOK 0x12 /* Message okie-dokie */ 112 #define ESP_CMD_TPAD 0x18 /* Transfer Pad */ 113 #define ESP_CMD_SATN 0x1a /* Set ATN */ 114 #define ESP_CMD_RATN 0x1b /* De-assert ATN */ 115 116 /* Group 3 commands: ESP must be in the MSGOUT or MSGIN state and be connected 117 * to a target as the initiator for these commands to work. 118 */ 119 #define ESP_CMD_SMSG 0x20 /* Send message */ 120 #define ESP_CMD_SSTAT 0x21 /* Send status */ 121 #define ESP_CMD_SDATA 0x22 /* Send data */ 122 #define ESP_CMD_DSEQ 0x23 /* Discontinue Sequence */ 123 #define ESP_CMD_TSEQ 0x24 /* Terminate Sequence */ 124 #define ESP_CMD_TCCSEQ 0x25 /* Target cmd cmplt sequence */ 125 #define ESP_CMD_DCNCT 0x27 /* Disconnect */ 126 #define ESP_CMD_RMSG 0x28 /* Receive Message */ 127 #define ESP_CMD_RCMD 0x29 /* Receive Command */ 128 #define ESP_CMD_RDATA 0x2a /* Receive Data */ 129 #define ESP_CMD_RCSEQ 0x2b /* Receive cmd sequence */ 130 131 /* Group 4 commands: The ESP must be in the disconnected state and must 132 * not be connected to any targets as initiator for 133 * these commands to work. 134 */ 135 #define ESP_CMD_RSEL 0x40 /* Reselect */ 136 #define ESP_CMD_SEL 0x41 /* Select w/o ATN */ 137 #define ESP_CMD_SELA 0x42 /* Select w/ATN */ 138 #define ESP_CMD_SELAS 0x43 /* Select w/ATN & STOP */ 139 #define ESP_CMD_ESEL 0x44 /* Enable selection */ 140 #define ESP_CMD_DSEL 0x45 /* Disable selections */ 141 #define ESP_CMD_SA3 0x46 /* Select w/ATN3 */ 142 #define ESP_CMD_RSEL3 0x47 /* Reselect3 */ 143 144 /* This bit enables the ESP's DMA on the SBus */ 145 #define ESP_CMD_DMA 0x80 /* Do DMA? */ 146 147 /* ESP status register read-only */ 148 #define ESP_STAT_PIO 0x01 /* IO phase bit */ 149 #define ESP_STAT_PCD 0x02 /* CD phase bit */ 150 #define ESP_STAT_PMSG 0x04 /* MSG phase bit */ 151 #define ESP_STAT_PMASK 0x07 /* Mask of phase bits */ 152 #define ESP_STAT_TDONE 0x08 /* Transfer Completed */ 153 #define ESP_STAT_TCNT 0x10 /* Transfer Counter Is Zero */ 154 #define ESP_STAT_PERR 0x20 /* Parity error */ 155 #define ESP_STAT_SPAM 0x40 /* Real bad error */ 156 /* This indicates the 'interrupt pending' condition on esp236, it is a reserved 157 * bit on other revs of the ESP. 158 */ 159 #define ESP_STAT_INTR 0x80 /* Interrupt */ 160 161 /* The status register can be masked with ESP_STAT_PMASK and compared 162 * with the following values to determine the current phase the ESP 163 * (at least thinks it) is in. For our purposes we also add our own 164 * software 'done' bit for our phase management engine. 165 */ 166 #define ESP_DOP (0) /* Data Out */ 167 #define ESP_DIP (ESP_STAT_PIO) /* Data In */ 168 #define ESP_CMDP (ESP_STAT_PCD) /* Command */ 169 #define ESP_STATP (ESP_STAT_PCD|ESP_STAT_PIO) /* Status */ 170 #define ESP_MOP (ESP_STAT_PMSG|ESP_STAT_PCD) /* Message Out */ 171 #define ESP_MIP (ESP_STAT_PMSG|ESP_STAT_PCD|ESP_STAT_PIO) /* Message In */ 172 173 /* HME only: status 2 register */ 174 #define ESP_STAT2_SCHBIT 0x01 /* Upper bits 3-7 of sstep enabled */ 175 #define ESP_STAT2_FFLAGS 0x02 /* The fifo flags are now latched */ 176 #define ESP_STAT2_XCNT 0x04 /* The transfer counter is latched */ 177 #define ESP_STAT2_CREGA 0x08 /* The command reg is active now */ 178 #define ESP_STAT2_WIDE 0x10 /* Interface on this adapter is wide */ 179 #define ESP_STAT2_F1BYTE 0x20 /* There is one byte at top of fifo */ 180 #define ESP_STAT2_FMSB 0x40 /* Next byte in fifo is most significant */ 181 #define ESP_STAT2_FEMPTY 0x80 /* FIFO is empty */ 182 183 /* ESP interrupt register read-only */ 184 #define ESP_INTR_S 0x01 /* Select w/o ATN */ 185 #define ESP_INTR_SATN 0x02 /* Select w/ATN */ 186 #define ESP_INTR_RSEL 0x04 /* Reselected */ 187 #define ESP_INTR_FDONE 0x08 /* Function done */ 188 #define ESP_INTR_BSERV 0x10 /* Bus service */ 189 #define ESP_INTR_DC 0x20 /* Disconnect */ 190 #define ESP_INTR_IC 0x40 /* Illegal command given */ 191 #define ESP_INTR_SR 0x80 /* SCSI bus reset detected */ 192 193 /* ESP sequence step register read-only */ 194 #define ESP_STEP_VBITS 0x07 /* Valid bits */ 195 #define ESP_STEP_ASEL 0x00 /* Selection&Arbitrate cmplt */ 196 #define ESP_STEP_SID 0x01 /* One msg byte sent */ 197 #define ESP_STEP_NCMD 0x02 /* Was not in command phase */ 198 #define ESP_STEP_PPC 0x03 /* Early phase chg caused cmnd 199 * bytes to be lost 200 */ 201 #define ESP_STEP_FINI4 0x04 /* Command was sent ok */ 202 203 /* Ho hum, some ESP's set the step register to this as well... */ 204 #define ESP_STEP_FINI5 0x05 205 #define ESP_STEP_FINI6 0x06 206 #define ESP_STEP_FINI7 0x07 207 208 /* ESP chip-test register read-write */ 209 #define ESP_TEST_TARG 0x01 /* Target test mode */ 210 #define ESP_TEST_INI 0x02 /* Initiator test mode */ 211 #define ESP_TEST_TS 0x04 /* Tristate test mode */ 212 213 /* ESP unique ID register read-only, found on fas236+fas100a only */ 214 #define ESP_UID_FAM 0xf8 /* ESP family bitmask */ 215 216 #define ESP_FAMILY(uid) (((uid) & ESP_UID_FAM) >> 3) 217 218 /* Values for the ESP family bits */ 219 #define ESP_UID_F100A 0x00 /* ESP FAS100A */ 220 #define ESP_UID_F236 0x02 /* ESP FAS236 */ 221 #define ESP_UID_HME 0x0a /* FAS HME */ 222 #define ESP_UID_FSC 0x14 /* NCR/Symbios Logic 53CF9x-2 */ 223 224 /* ESP fifo flags register read-only */ 225 /* Note that the following implies a 16 byte FIFO on the ESP. */ 226 #define ESP_FF_FBYTES 0x1f /* Num bytes in FIFO */ 227 #define ESP_FF_ONOTZERO 0x20 /* offset ctr not zero (esp100) */ 228 #define ESP_FF_SSTEP 0xe0 /* Sequence step */ 229 230 /* ESP clock conversion factor register write-only */ 231 #define ESP_CCF_F0 0x00 /* 35.01MHz - 40MHz */ 232 #define ESP_CCF_NEVER 0x01 /* Set it to this and die */ 233 #define ESP_CCF_F2 0x02 /* 10MHz */ 234 #define ESP_CCF_F3 0x03 /* 10.01MHz - 15MHz */ 235 #define ESP_CCF_F4 0x04 /* 15.01MHz - 20MHz */ 236 #define ESP_CCF_F5 0x05 /* 20.01MHz - 25MHz */ 237 #define ESP_CCF_F6 0x06 /* 25.01MHz - 30MHz */ 238 #define ESP_CCF_F7 0x07 /* 30.01MHz - 35MHz */ 239 240 /* HME only... */ 241 #define ESP_BUSID_RESELID 0x10 242 #define ESP_BUSID_CTR32BIT 0x40 243 244 #define ESP_BUS_TIMEOUT 250 /* In milli-seconds */ 245 #define ESP_TIMEO_CONST 8192 246 #define ESP_NEG_DEFP(mhz, cfact) \ 247 ((ESP_BUS_TIMEOUT * ((mhz) / 1000)) / (8192 * (cfact))) 248 #define ESP_HZ_TO_CYCLE(hertz) ((1000000000) / ((hertz) / 1000)) 249 #define ESP_TICK(ccf, cycle) ((7682 * (ccf) * (cycle) / 1000)) 250 251 /* For slow to medium speed input clock rates we shoot for 5mb/s, but for high 252 * input clock rates we try to do 10mb/s although I don't think a transfer can 253 * even run that fast with an ESP even with DMA2 scatter gather pipelining. 254 */ 255 #define SYNC_DEFP_SLOW 0x32 /* 5mb/s */ 256 #define SYNC_DEFP_FAST 0x19 /* 10mb/s */ 257 258 struct esp_cmd_priv { 259 int num_sg; 260 int cur_residue; 261 struct scatterlist *prv_sg; 262 struct scatterlist *cur_sg; 263 int tot_residue; 264 }; 265 266 #define ESP_CMD_PRIV(cmd) ((struct esp_cmd_priv *)scsi_cmd_priv(cmd)) 267 268 /* NOTE: this enum is ordered based on chip features! */ 269 enum esp_rev { 270 ESP100, /* NCR53C90 - very broken */ 271 ESP100A, /* NCR53C90A */ 272 ESP236, 273 FAS236, 274 PCSCSI, /* AM53c974 */ 275 FSC, /* NCR/Symbios Logic 53CF9x-2 */ 276 FAS100A, 277 FAST, 278 FASHME, 279 }; 280 281 struct esp_cmd_entry { 282 struct list_head list; 283 284 struct scsi_cmnd *cmd; 285 286 unsigned int saved_cur_residue; 287 struct scatterlist *saved_prv_sg; 288 struct scatterlist *saved_cur_sg; 289 unsigned int saved_tot_residue; 290 291 u8 flags; 292 #define ESP_CMD_FLAG_WRITE 0x01 /* DMA is a write */ 293 #define ESP_CMD_FLAG_AUTOSENSE 0x04 /* Doing automatic REQUEST_SENSE */ 294 #define ESP_CMD_FLAG_RESIDUAL 0x08 /* AM53c974 BLAST residual */ 295 296 u8 tag[2]; 297 u8 orig_tag[2]; 298 299 u8 status; 300 u8 message; 301 302 unsigned char *sense_ptr; 303 unsigned char *saved_sense_ptr; 304 dma_addr_t sense_dma; 305 306 struct completion *eh_done; 307 }; 308 309 #define ESP_DEFAULT_TAGS 16 310 311 #define ESP_MAX_TARGET 16 312 #define ESP_MAX_LUN 8 313 #define ESP_MAX_TAG 256 314 315 struct esp_lun_data { 316 struct esp_cmd_entry *non_tagged_cmd; 317 int num_tagged; 318 int hold; 319 struct esp_cmd_entry *tagged_cmds[ESP_MAX_TAG]; 320 }; 321 322 struct esp_target_data { 323 /* These are the ESP_STP, ESP_SOFF, and ESP_CFG3 register values which 324 * match the currently negotiated settings for this target. The SCSI 325 * protocol values are maintained in spi_{offset,period,wide}(starget). 326 */ 327 u8 esp_period; 328 u8 esp_offset; 329 u8 esp_config3; 330 331 u8 flags; 332 #define ESP_TGT_WIDE 0x01 333 #define ESP_TGT_DISCONNECT 0x02 334 #define ESP_TGT_NEGO_WIDE 0x04 335 #define ESP_TGT_NEGO_SYNC 0x08 336 #define ESP_TGT_CHECK_NEGO 0x40 337 #define ESP_TGT_BROKEN 0x80 338 339 /* When ESP_TGT_CHECK_NEGO is set, on the next scsi command to this 340 * device we will try to negotiate the following parameters. 341 */ 342 u8 nego_goal_period; 343 u8 nego_goal_offset; 344 u8 nego_goal_width; 345 u8 nego_goal_tags; 346 347 struct scsi_target *starget; 348 }; 349 350 struct esp_event_ent { 351 u8 type; 352 #define ESP_EVENT_TYPE_EVENT 0x01 353 #define ESP_EVENT_TYPE_CMD 0x02 354 u8 val; 355 356 u8 sreg; 357 u8 seqreg; 358 u8 sreg2; 359 u8 ireg; 360 u8 select_state; 361 u8 event; 362 u8 __pad; 363 }; 364 365 struct esp; 366 struct esp_driver_ops { 367 /* Read and write the ESP 8-bit registers. On some 368 * applications of the ESP chip the registers are at 4-byte 369 * instead of 1-byte intervals. 370 */ 371 void (*esp_write8)(struct esp *esp, u8 val, unsigned long reg); 372 u8 (*esp_read8)(struct esp *esp, unsigned long reg); 373 374 /* Return non-zero if there is an IRQ pending. Usually this 375 * status bit lives in the DMA controller sitting in front of 376 * the ESP. This has to be accurate or else the ESP interrupt 377 * handler will not run. 378 */ 379 int (*irq_pending)(struct esp *esp); 380 381 /* Return the maximum allowable size of a DMA transfer for a 382 * given buffer. 383 */ 384 u32 (*dma_length_limit)(struct esp *esp, u32 dma_addr, 385 u32 dma_len); 386 387 /* Reset the DMA engine entirely. On return, ESP interrupts 388 * should be enabled. Often the interrupt enabling is 389 * controlled in the DMA engine. 390 */ 391 void (*reset_dma)(struct esp *esp); 392 393 /* Drain any pending DMA in the DMA engine after a transfer. 394 * This is for writes to memory. 395 */ 396 void (*dma_drain)(struct esp *esp); 397 398 /* Invalidate the DMA engine after a DMA transfer. */ 399 void (*dma_invalidate)(struct esp *esp); 400 401 /* Setup an ESP command that will use a DMA transfer. 402 * The 'esp_count' specifies what transfer length should be 403 * programmed into the ESP transfer counter registers, whereas 404 * the 'dma_count' is the length that should be programmed into 405 * the DMA controller. Usually they are the same. If 'write' 406 * is non-zero, this transfer is a write into memory. 'cmd' 407 * holds the ESP command that should be issued by calling 408 * scsi_esp_cmd() at the appropriate time while programming 409 * the DMA hardware. 410 */ 411 void (*send_dma_cmd)(struct esp *esp, u32 dma_addr, u32 esp_count, 412 u32 dma_count, int write, u8 cmd); 413 414 /* Return non-zero if the DMA engine is reporting an error 415 * currently. 416 */ 417 int (*dma_error)(struct esp *esp); 418 }; 419 420 #define ESP_MAX_MSG_SZ 8 421 #define ESP_EVENT_LOG_SZ 32 422 423 #define ESP_QUICKIRQ_LIMIT 100 424 #define ESP_RESELECT_TAG_LIMIT 2500 425 426 struct esp { 427 void __iomem *regs; 428 void __iomem *dma_regs; 429 430 const struct esp_driver_ops *ops; 431 432 struct Scsi_Host *host; 433 struct device *dev; 434 435 struct esp_cmd_entry *active_cmd; 436 437 struct list_head queued_cmds; 438 struct list_head active_cmds; 439 440 u8 *command_block; 441 dma_addr_t command_block_dma; 442 443 unsigned int data_dma_len; 444 445 /* The following are used to determine the cause of an IRQ. Upon every 446 * IRQ entry we synchronize these with the hardware registers. 447 */ 448 u8 sreg; 449 u8 seqreg; 450 u8 sreg2; 451 u8 ireg; 452 453 u32 prev_hme_dmacsr; 454 u8 prev_soff; 455 u8 prev_stp; 456 u8 prev_cfg3; 457 u8 num_tags; 458 459 struct list_head esp_cmd_pool; 460 461 struct esp_target_data target[ESP_MAX_TARGET]; 462 463 int fifo_cnt; 464 u8 fifo[16]; 465 466 struct esp_event_ent esp_event_log[ESP_EVENT_LOG_SZ]; 467 int esp_event_cur; 468 469 u8 msg_out[ESP_MAX_MSG_SZ]; 470 int msg_out_len; 471 472 u8 msg_in[ESP_MAX_MSG_SZ]; 473 int msg_in_len; 474 475 u8 bursts; 476 u8 config1; 477 u8 config2; 478 u8 config4; 479 480 u8 scsi_id; 481 u32 scsi_id_mask; 482 483 enum esp_rev rev; 484 485 u32 flags; 486 #define ESP_FLAG_DIFFERENTIAL 0x00000001 487 #define ESP_FLAG_RESETTING 0x00000002 488 #define ESP_FLAG_WIDE_CAPABLE 0x00000008 489 #define ESP_FLAG_QUICKIRQ_CHECK 0x00000010 490 #define ESP_FLAG_DISABLE_SYNC 0x00000020 491 #define ESP_FLAG_USE_FIFO 0x00000040 492 #define ESP_FLAG_NO_DMA_MAP 0x00000080 493 494 u8 select_state; 495 #define ESP_SELECT_NONE 0x00 /* Not selecting */ 496 #define ESP_SELECT_BASIC 0x01 /* Select w/o MSGOUT phase */ 497 #define ESP_SELECT_MSGOUT 0x02 /* Select with MSGOUT */ 498 499 /* When we are not selecting, we are expecting an event. */ 500 u8 event; 501 #define ESP_EVENT_NONE 0x00 502 #define ESP_EVENT_CMD_START 0x01 503 #define ESP_EVENT_CMD_DONE 0x02 504 #define ESP_EVENT_DATA_IN 0x03 505 #define ESP_EVENT_DATA_OUT 0x04 506 #define ESP_EVENT_DATA_DONE 0x05 507 #define ESP_EVENT_MSGIN 0x06 508 #define ESP_EVENT_MSGIN_MORE 0x07 509 #define ESP_EVENT_MSGIN_DONE 0x08 510 #define ESP_EVENT_MSGOUT 0x09 511 #define ESP_EVENT_MSGOUT_DONE 0x0a 512 #define ESP_EVENT_STATUS 0x0b 513 #define ESP_EVENT_FREE_BUS 0x0c 514 #define ESP_EVENT_CHECK_PHASE 0x0d 515 #define ESP_EVENT_RESET 0x10 516 517 /* Probed in esp_get_clock_params() */ 518 u32 cfact; 519 u32 cfreq; 520 u32 ccycle; 521 u32 ctick; 522 u32 neg_defp; 523 u32 sync_defp; 524 525 /* Computed in esp_reset_esp() */ 526 u32 max_period; 527 u32 min_period; 528 u32 radelay; 529 530 /* ESP_CMD_SELAS command state */ 531 u8 *cmd_bytes_ptr; 532 int cmd_bytes_left; 533 534 struct completion *eh_reset; 535 536 void *dma; 537 int dmarev; 538 539 /* These are used by esp_send_pio_cmd() */ 540 u8 __iomem *fifo_reg; 541 int send_cmd_error; 542 u32 send_cmd_residual; 543 }; 544 545 /* A front-end driver for the ESP chip should do the following in 546 * it's device probe routine: 547 * 1) Allocate the host and private area using scsi_host_alloc() 548 * with size 'sizeof(struct esp)'. The first argument to 549 * scsi_host_alloc() should be &scsi_esp_template. 550 * 2) Set host->max_id as appropriate. 551 * 3) Set esp->host to the scsi_host itself, and esp->dev 552 * to the device object pointer. 553 * 4) Hook up esp->ops to the front-end implementation. 554 * 5) If the ESP chip supports wide transfers, set ESP_FLAG_WIDE_CAPABLE 555 * in esp->flags. 556 * 6) Map the DMA and ESP chip registers. 557 * 7) DMA map the ESP command block, store the DMA address 558 * in esp->command_block_dma. 559 * 8) Register the scsi_esp_intr() interrupt handler. 560 * 9) Probe for and provide the following chip properties: 561 * esp->scsi_id (assign to esp->host->this_id too) 562 * esp->scsi_id_mask 563 * If ESP bus is differential, set ESP_FLAG_DIFFERENTIAL 564 * esp->cfreq 565 * DMA burst bit mask in esp->bursts, if necessary 566 * 10) Perform any actions necessary before the ESP device can 567 * be programmed for the first time. On some configs, for 568 * example, the DMA engine has to be reset before ESP can 569 * be programmed. 570 * 11) If necessary, call dev_set_drvdata() as needed. 571 * 12) Call scsi_esp_register() with prepared 'esp' structure. 572 * 13) Check scsi_esp_register() return value, release all resources 573 * if an error was returned. 574 */ 575 extern struct scsi_host_template scsi_esp_template; 576 extern int scsi_esp_register(struct esp *); 577 578 extern void scsi_esp_unregister(struct esp *); 579 extern irqreturn_t scsi_esp_intr(int, void *); 580 extern void scsi_esp_cmd(struct esp *, u8); 581 582 extern void esp_send_pio_cmd(struct esp *esp, u32 dma_addr, u32 esp_count, 583 u32 dma_count, int write, u8 cmd); 584 585 #endif /* !(_ESP_SCSI_H) */ 586