1 /* 2 * dc395x.c 3 * 4 * Device Driver for Tekram DC395(U/UW/F), DC315(U) 5 * PCI SCSI Bus Master Host Adapter 6 * (SCSI chip set used Tekram ASIC TRM-S1040) 7 * 8 * Authors: 9 * C.L. Huang <ching@tekram.com.tw> 10 * Erich Chen <erich@tekram.com.tw> 11 * (C) Copyright 1995-1999 Tekram Technology Co., Ltd. 12 * 13 * Kurt Garloff <garloff@suse.de> 14 * (C) 1999-2000 Kurt Garloff 15 * 16 * Oliver Neukum <oliver@neukum.name> 17 * Ali Akcaagac <aliakc@web.de> 18 * Jamie Lenehan <lenehan@twibble.org> 19 * (C) 2003 20 * 21 * License: GNU GPL 22 * 23 ************************************************************************* 24 * 25 * Redistribution and use in source and binary forms, with or without 26 * modification, are permitted provided that the following conditions 27 * are met: 28 * 1. Redistributions of source code must retain the above copyright 29 * notice, this list of conditions and the following disclaimer. 30 * 2. Redistributions in binary form must reproduce the above copyright 31 * notice, this list of conditions and the following disclaimer in the 32 * documentation and/or other materials provided with the distribution. 33 * 3. The name of the author may not be used to endorse or promote products 34 * derived from this software without specific prior written permission. 35 * 36 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 37 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 38 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 39 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, 40 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 41 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 42 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 43 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 44 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF 45 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 46 * 47 ************************************************************************ 48 */ 49 #include <linux/module.h> 50 #include <linux/moduleparam.h> 51 #include <linux/delay.h> 52 #include <linux/ctype.h> 53 #include <linux/blkdev.h> 54 #include <linux/interrupt.h> 55 #include <linux/init.h> 56 #include <linux/spinlock.h> 57 #include <linux/pci.h> 58 #include <linux/list.h> 59 #include <linux/vmalloc.h> 60 #include <asm/io.h> 61 62 #include <scsi/scsi.h> 63 #include <scsi/scsicam.h> /* needed for scsicam_bios_param */ 64 #include <scsi/scsi_cmnd.h> 65 #include <scsi/scsi_device.h> 66 #include <scsi/scsi_host.h> 67 68 #include "dc395x.h" 69 70 #define DC395X_NAME "dc395x" 71 #define DC395X_BANNER "Tekram DC395(U/UW/F), DC315(U) - ASIC TRM-S1040" 72 #define DC395X_VERSION "v2.05, 2004/03/08" 73 74 /*--------------------------------------------------------------------------- 75 Features 76 ---------------------------------------------------------------------------*/ 77 /* 78 * Set to disable parts of the driver 79 */ 80 /*#define DC395x_NO_DISCONNECT*/ 81 /*#define DC395x_NO_TAGQ*/ 82 /*#define DC395x_NO_SYNC*/ 83 /*#define DC395x_NO_WIDE*/ 84 85 /*--------------------------------------------------------------------------- 86 Debugging 87 ---------------------------------------------------------------------------*/ 88 /* 89 * Types of debugging that can be enabled and disabled 90 */ 91 #define DBG_KG 0x0001 92 #define DBG_0 0x0002 93 #define DBG_1 0x0004 94 #define DBG_SG 0x0020 95 #define DBG_FIFO 0x0040 96 #define DBG_PIO 0x0080 97 98 99 /* 100 * Set set of things to output debugging for. 101 * Undefine to remove all debugging 102 */ 103 /*#define DEBUG_MASK (DBG_0|DBG_1|DBG_SG|DBG_FIFO|DBG_PIO)*/ 104 /*#define DEBUG_MASK DBG_0*/ 105 106 107 /* 108 * Output a kernel mesage at the specified level and append the 109 * driver name and a ": " to the start of the message 110 */ 111 #define dprintkl(level, format, arg...) \ 112 printk(level DC395X_NAME ": " format , ## arg) 113 114 115 #ifdef DEBUG_MASK 116 /* 117 * print a debug message - this is formated with KERN_DEBUG, then the 118 * driver name followed by a ": " and then the message is output. 119 * This also checks that the specified debug level is enabled before 120 * outputing the message 121 */ 122 #define dprintkdbg(type, format, arg...) \ 123 do { \ 124 if ((type) & (DEBUG_MASK)) \ 125 dprintkl(KERN_DEBUG , format , ## arg); \ 126 } while (0) 127 128 /* 129 * Check if the specified type of debugging is enabled 130 */ 131 #define debug_enabled(type) ((DEBUG_MASK) & (type)) 132 133 #else 134 /* 135 * No debugging. Do nothing 136 */ 137 #define dprintkdbg(type, format, arg...) \ 138 do {} while (0) 139 #define debug_enabled(type) (0) 140 141 #endif 142 143 144 #ifndef PCI_VENDOR_ID_TEKRAM 145 #define PCI_VENDOR_ID_TEKRAM 0x1DE1 /* Vendor ID */ 146 #endif 147 #ifndef PCI_DEVICE_ID_TEKRAM_TRMS1040 148 #define PCI_DEVICE_ID_TEKRAM_TRMS1040 0x0391 /* Device ID */ 149 #endif 150 151 152 #define DC395x_LOCK_IO(dev,flags) spin_lock_irqsave(((struct Scsi_Host *)dev)->host_lock, flags) 153 #define DC395x_UNLOCK_IO(dev,flags) spin_unlock_irqrestore(((struct Scsi_Host *)dev)->host_lock, flags) 154 155 #define DC395x_read8(acb,address) (u8)(inb(acb->io_port_base + (address))) 156 #define DC395x_read16(acb,address) (u16)(inw(acb->io_port_base + (address))) 157 #define DC395x_read32(acb,address) (u32)(inl(acb->io_port_base + (address))) 158 #define DC395x_write8(acb,address,value) outb((value), acb->io_port_base + (address)) 159 #define DC395x_write16(acb,address,value) outw((value), acb->io_port_base + (address)) 160 #define DC395x_write32(acb,address,value) outl((value), acb->io_port_base + (address)) 161 162 /* cmd->result */ 163 #define RES_TARGET 0x000000FF /* Target State */ 164 #define RES_TARGET_LNX STATUS_MASK /* Only official ... */ 165 #define RES_ENDMSG 0x0000FF00 /* End Message */ 166 #define RES_DID 0x00FF0000 /* DID_ codes */ 167 #define RES_DRV 0xFF000000 /* DRIVER_ codes */ 168 169 #define MK_RES(drv,did,msg,tgt) ((int)(drv)<<24 | (int)(did)<<16 | (int)(msg)<<8 | (int)(tgt)) 170 #define MK_RES_LNX(drv,did,msg,tgt) ((int)(drv)<<24 | (int)(did)<<16 | (int)(msg)<<8 | (int)(tgt)<<1) 171 172 #define SET_RES_TARGET(who,tgt) { who &= ~RES_TARGET; who |= (int)(tgt); } 173 #define SET_RES_TARGET_LNX(who,tgt) { who &= ~RES_TARGET_LNX; who |= (int)(tgt) << 1; } 174 #define SET_RES_MSG(who,msg) { who &= ~RES_ENDMSG; who |= (int)(msg) << 8; } 175 #define SET_RES_DID(who,did) { who &= ~RES_DID; who |= (int)(did) << 16; } 176 #define SET_RES_DRV(who,drv) { who &= ~RES_DRV; who |= (int)(drv) << 24; } 177 178 #define TAG_NONE 255 179 180 /* 181 * srb->segement_x is the hw sg list. It is always allocated as a 182 * DC395x_MAX_SG_LISTENTRY entries in a linear block which does not 183 * cross a page boundy. 184 */ 185 #define SEGMENTX_LEN (sizeof(struct SGentry)*DC395x_MAX_SG_LISTENTRY) 186 187 188 struct SGentry { 189 u32 address; /* bus! address */ 190 u32 length; 191 }; 192 193 /* The SEEPROM structure for TRM_S1040 */ 194 struct NVRamTarget { 195 u8 cfg0; /* Target configuration byte 0 */ 196 u8 period; /* Target period */ 197 u8 cfg2; /* Target configuration byte 2 */ 198 u8 cfg3; /* Target configuration byte 3 */ 199 }; 200 201 struct NvRamType { 202 u8 sub_vendor_id[2]; /* 0,1 Sub Vendor ID */ 203 u8 sub_sys_id[2]; /* 2,3 Sub System ID */ 204 u8 sub_class; /* 4 Sub Class */ 205 u8 vendor_id[2]; /* 5,6 Vendor ID */ 206 u8 device_id[2]; /* 7,8 Device ID */ 207 u8 reserved; /* 9 Reserved */ 208 struct NVRamTarget target[DC395x_MAX_SCSI_ID]; 209 /** 10,11,12,13 210 ** 14,15,16,17 211 ** .... 212 ** .... 213 ** 70,71,72,73 214 */ 215 u8 scsi_id; /* 74 Host Adapter SCSI ID */ 216 u8 channel_cfg; /* 75 Channel configuration */ 217 u8 delay_time; /* 76 Power on delay time */ 218 u8 max_tag; /* 77 Maximum tags */ 219 u8 reserved0; /* 78 */ 220 u8 boot_target; /* 79 */ 221 u8 boot_lun; /* 80 */ 222 u8 reserved1; /* 81 */ 223 u16 reserved2[22]; /* 82,..125 */ 224 u16 cksum; /* 126,127 */ 225 }; 226 227 struct ScsiReqBlk { 228 struct list_head list; /* next/prev ptrs for srb lists */ 229 struct DeviceCtlBlk *dcb; 230 struct scsi_cmnd *cmd; 231 232 struct SGentry *segment_x; /* Linear array of hw sg entries (up to 64 entries) */ 233 dma_addr_t sg_bus_addr; /* Bus address of sg list (ie, of segment_x) */ 234 235 u8 sg_count; /* No of HW sg entries for this request */ 236 u8 sg_index; /* Index of HW sg entry for this request */ 237 size_t total_xfer_length; /* Total number of bytes remaining to be transfered */ 238 size_t request_length; /* Total number of bytes in this request */ 239 /* 240 * The sense buffer handling function, request_sense, uses 241 * the first hw sg entry (segment_x[0]) and the transfer 242 * length (total_xfer_length). While doing this it stores the 243 * original values into the last sg hw list 244 * (srb->segment_x[DC395x_MAX_SG_LISTENTRY - 1] and the 245 * total_xfer_length in xferred. These values are restored in 246 * pci_unmap_srb_sense. This is the only place xferred is used. 247 */ 248 size_t xferred; /* Saved copy of total_xfer_length */ 249 250 u16 state; 251 252 u8 msgin_buf[6]; 253 u8 msgout_buf[6]; 254 255 u8 adapter_status; 256 u8 target_status; 257 u8 msg_count; 258 u8 end_message; 259 260 u8 tag_number; 261 u8 status; 262 u8 retry_count; 263 u8 flag; 264 265 u8 scsi_phase; 266 }; 267 268 struct DeviceCtlBlk { 269 struct list_head list; /* next/prev ptrs for the dcb list */ 270 struct AdapterCtlBlk *acb; 271 struct list_head srb_going_list; /* head of going srb list */ 272 struct list_head srb_waiting_list; /* head of waiting srb list */ 273 274 struct ScsiReqBlk *active_srb; 275 u32 tag_mask; 276 277 u16 max_command; 278 279 u8 target_id; /* SCSI Target ID (SCSI Only) */ 280 u8 target_lun; /* SCSI Log. Unit (SCSI Only) */ 281 u8 identify_msg; 282 u8 dev_mode; 283 284 u8 inquiry7; /* To store Inquiry flags */ 285 u8 sync_mode; /* 0:async mode */ 286 u8 min_nego_period; /* for nego. */ 287 u8 sync_period; /* for reg. */ 288 289 u8 sync_offset; /* for reg. and nego.(low nibble) */ 290 u8 flag; 291 u8 dev_type; 292 u8 init_tcq_flag; 293 }; 294 295 struct AdapterCtlBlk { 296 struct Scsi_Host *scsi_host; 297 298 unsigned long io_port_base; 299 unsigned long io_port_len; 300 301 struct list_head dcb_list; /* head of going dcb list */ 302 struct DeviceCtlBlk *dcb_run_robin; 303 struct DeviceCtlBlk *active_dcb; 304 305 struct list_head srb_free_list; /* head of free srb list */ 306 struct ScsiReqBlk *tmp_srb; 307 struct timer_list waiting_timer; 308 struct timer_list selto_timer; 309 310 u16 srb_count; 311 312 u8 sel_timeout; 313 314 unsigned int irq_level; 315 u8 tag_max_num; 316 u8 acb_flag; 317 u8 gmode2; 318 319 u8 config; 320 u8 lun_chk; 321 u8 scan_devices; 322 u8 hostid_bit; 323 324 u8 dcb_map[DC395x_MAX_SCSI_ID]; 325 struct DeviceCtlBlk *children[DC395x_MAX_SCSI_ID][32]; 326 327 struct pci_dev *dev; 328 329 u8 msg_len; 330 331 struct ScsiReqBlk srb_array[DC395x_MAX_SRB_CNT]; 332 struct ScsiReqBlk srb; 333 334 struct NvRamType eeprom; /* eeprom settings for this adapter */ 335 }; 336 337 338 /*--------------------------------------------------------------------------- 339 Forward declarations 340 ---------------------------------------------------------------------------*/ 341 static void data_out_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 342 u16 *pscsi_status); 343 static void data_in_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 344 u16 *pscsi_status); 345 static void command_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 346 u16 *pscsi_status); 347 static void status_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 348 u16 *pscsi_status); 349 static void msgout_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 350 u16 *pscsi_status); 351 static void msgin_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 352 u16 *pscsi_status); 353 static void data_out_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 354 u16 *pscsi_status); 355 static void data_in_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 356 u16 *pscsi_status); 357 static void command_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 358 u16 *pscsi_status); 359 static void status_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 360 u16 *pscsi_status); 361 static void msgout_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 362 u16 *pscsi_status); 363 static void msgin_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 364 u16 *pscsi_status); 365 static void nop0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 366 u16 *pscsi_status); 367 static void nop1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 368 u16 *pscsi_status); 369 static void set_basic_config(struct AdapterCtlBlk *acb); 370 static void cleanup_after_transfer(struct AdapterCtlBlk *acb, 371 struct ScsiReqBlk *srb); 372 static void reset_scsi_bus(struct AdapterCtlBlk *acb); 373 static void data_io_transfer(struct AdapterCtlBlk *acb, 374 struct ScsiReqBlk *srb, u16 io_dir); 375 static void disconnect(struct AdapterCtlBlk *acb); 376 static void reselect(struct AdapterCtlBlk *acb); 377 static u8 start_scsi(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 378 struct ScsiReqBlk *srb); 379 static inline void enable_msgout_abort(struct AdapterCtlBlk *acb, 380 struct ScsiReqBlk *srb); 381 static void build_srb(struct scsi_cmnd *cmd, struct DeviceCtlBlk *dcb, 382 struct ScsiReqBlk *srb); 383 static void doing_srb_done(struct AdapterCtlBlk *acb, u8 did_code, 384 struct scsi_cmnd *cmd, u8 force); 385 static void scsi_reset_detect(struct AdapterCtlBlk *acb); 386 static void pci_unmap_srb(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb); 387 static void pci_unmap_srb_sense(struct AdapterCtlBlk *acb, 388 struct ScsiReqBlk *srb); 389 static void srb_done(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 390 struct ScsiReqBlk *srb); 391 static void request_sense(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 392 struct ScsiReqBlk *srb); 393 static void set_xfer_rate(struct AdapterCtlBlk *acb, 394 struct DeviceCtlBlk *dcb); 395 static void waiting_timeout(unsigned long ptr); 396 397 398 /*--------------------------------------------------------------------------- 399 Static Data 400 ---------------------------------------------------------------------------*/ 401 static u16 current_sync_offset = 0; 402 403 static void *dc395x_scsi_phase0[] = { 404 data_out_phase0,/* phase:0 */ 405 data_in_phase0, /* phase:1 */ 406 command_phase0, /* phase:2 */ 407 status_phase0, /* phase:3 */ 408 nop0, /* phase:4 PH_BUS_FREE .. initial phase */ 409 nop0, /* phase:5 PH_BUS_FREE .. initial phase */ 410 msgout_phase0, /* phase:6 */ 411 msgin_phase0, /* phase:7 */ 412 }; 413 414 static void *dc395x_scsi_phase1[] = { 415 data_out_phase1,/* phase:0 */ 416 data_in_phase1, /* phase:1 */ 417 command_phase1, /* phase:2 */ 418 status_phase1, /* phase:3 */ 419 nop1, /* phase:4 PH_BUS_FREE .. initial phase */ 420 nop1, /* phase:5 PH_BUS_FREE .. initial phase */ 421 msgout_phase1, /* phase:6 */ 422 msgin_phase1, /* phase:7 */ 423 }; 424 425 /* 426 *Fast20: 000 50ns, 20.0 MHz 427 * 001 75ns, 13.3 MHz 428 * 010 100ns, 10.0 MHz 429 * 011 125ns, 8.0 MHz 430 * 100 150ns, 6.6 MHz 431 * 101 175ns, 5.7 MHz 432 * 110 200ns, 5.0 MHz 433 * 111 250ns, 4.0 MHz 434 * 435 *Fast40(LVDS): 000 25ns, 40.0 MHz 436 * 001 50ns, 20.0 MHz 437 * 010 75ns, 13.3 MHz 438 * 011 100ns, 10.0 MHz 439 * 100 125ns, 8.0 MHz 440 * 101 150ns, 6.6 MHz 441 * 110 175ns, 5.7 MHz 442 * 111 200ns, 5.0 MHz 443 */ 444 /*static u8 clock_period[] = {12,19,25,31,37,44,50,62};*/ 445 446 /* real period:48ns,76ns,100ns,124ns,148ns,176ns,200ns,248ns */ 447 static u8 clock_period[] = { 12, 18, 25, 31, 37, 43, 50, 62 }; 448 static u16 clock_speed[] = { 200, 133, 100, 80, 67, 58, 50, 40 }; 449 450 451 /*--------------------------------------------------------------------------- 452 Configuration 453 ---------------------------------------------------------------------------*/ 454 /* 455 * Module/boot parameters currently effect *all* instances of the 456 * card in the system. 457 */ 458 459 /* 460 * Command line parameters are stored in a structure below. 461 * These are the index's into the structure for the various 462 * command line options. 463 */ 464 #define CFG_ADAPTER_ID 0 465 #define CFG_MAX_SPEED 1 466 #define CFG_DEV_MODE 2 467 #define CFG_ADAPTER_MODE 3 468 #define CFG_TAGS 4 469 #define CFG_RESET_DELAY 5 470 471 #define CFG_NUM 6 /* number of configuration items */ 472 473 474 /* 475 * Value used to indicate that a command line override 476 * hasn't been used to modify the value. 477 */ 478 #define CFG_PARAM_UNSET -1 479 480 481 /* 482 * Hold command line parameters. 483 */ 484 struct ParameterData { 485 int value; /* value of this setting */ 486 int min; /* minimum value */ 487 int max; /* maximum value */ 488 int def; /* default value */ 489 int safe; /* safe value */ 490 }; 491 static struct ParameterData __devinitdata cfg_data[] = { 492 { /* adapter id */ 493 CFG_PARAM_UNSET, 494 0, 495 15, 496 7, 497 7 498 }, 499 { /* max speed */ 500 CFG_PARAM_UNSET, 501 0, 502 7, 503 1, /* 13.3Mhz */ 504 4, /* 6.7Hmz */ 505 }, 506 { /* dev mode */ 507 CFG_PARAM_UNSET, 508 0, 509 0x3f, 510 NTC_DO_PARITY_CHK | NTC_DO_DISCONNECT | NTC_DO_SYNC_NEGO | 511 NTC_DO_WIDE_NEGO | NTC_DO_TAG_QUEUEING | 512 NTC_DO_SEND_START, 513 NTC_DO_PARITY_CHK | NTC_DO_SEND_START 514 }, 515 { /* adapter mode */ 516 CFG_PARAM_UNSET, 517 0, 518 0x2f, 519 #ifdef CONFIG_SCSI_MULTI_LUN 520 NAC_SCANLUN | 521 #endif 522 NAC_GT2DRIVES | NAC_GREATER_1G | NAC_POWERON_SCSI_RESET 523 /*| NAC_ACTIVE_NEG*/, 524 NAC_GT2DRIVES | NAC_GREATER_1G | NAC_POWERON_SCSI_RESET | 0x08 525 }, 526 { /* tags */ 527 CFG_PARAM_UNSET, 528 0, 529 5, 530 3, /* 16 tags (??) */ 531 2, 532 }, 533 { /* reset delay */ 534 CFG_PARAM_UNSET, 535 0, 536 180, 537 1, /* 1 second */ 538 10, /* 10 seconds */ 539 } 540 }; 541 542 543 /* 544 * Safe settings. If set to zero the the BIOS/default values with 545 * command line overrides will be used. If set to 1 then safe and 546 * slow settings will be used. 547 */ 548 static int use_safe_settings = 0; 549 module_param_named(safe, use_safe_settings, bool, 0); 550 MODULE_PARM_DESC(safe, "Use safe and slow settings only. Default: false"); 551 552 553 module_param_named(adapter_id, cfg_data[CFG_ADAPTER_ID].value, int, 0); 554 MODULE_PARM_DESC(adapter_id, "Adapter SCSI ID. Default 7 (0-15)"); 555 556 module_param_named(max_speed, cfg_data[CFG_MAX_SPEED].value, int, 0); 557 MODULE_PARM_DESC(max_speed, "Maximum bus speed. Default 1 (0-7) Speeds: 0=20, 1=13.3, 2=10, 3=8, 4=6.7, 5=5.8, 6=5, 7=4 Mhz"); 558 559 module_param_named(dev_mode, cfg_data[CFG_DEV_MODE].value, int, 0); 560 MODULE_PARM_DESC(dev_mode, "Device mode."); 561 562 module_param_named(adapter_mode, cfg_data[CFG_ADAPTER_MODE].value, int, 0); 563 MODULE_PARM_DESC(adapter_mode, "Adapter mode."); 564 565 module_param_named(tags, cfg_data[CFG_TAGS].value, int, 0); 566 MODULE_PARM_DESC(tags, "Number of tags (1<<x). Default 3 (0-5)"); 567 568 module_param_named(reset_delay, cfg_data[CFG_RESET_DELAY].value, int, 0); 569 MODULE_PARM_DESC(reset_delay, "Reset delay in seconds. Default 1 (0-180)"); 570 571 572 /** 573 * set_safe_settings - if the use_safe_settings option is set then 574 * set all values to the safe and slow values. 575 **/ 576 static void __devinit set_safe_settings(void) 577 { 578 if (use_safe_settings) 579 { 580 int i; 581 582 dprintkl(KERN_INFO, "Using safe settings.\n"); 583 for (i = 0; i < CFG_NUM; i++) 584 { 585 cfg_data[i].value = cfg_data[i].safe; 586 } 587 } 588 } 589 590 591 /** 592 * fix_settings - reset any boot parameters which are out of range 593 * back to the default values. 594 **/ 595 static void __devinit fix_settings(void) 596 { 597 int i; 598 599 dprintkdbg(DBG_1, 600 "setup: AdapterId=%08x MaxSpeed=%08x DevMode=%08x " 601 "AdapterMode=%08x Tags=%08x ResetDelay=%08x\n", 602 cfg_data[CFG_ADAPTER_ID].value, 603 cfg_data[CFG_MAX_SPEED].value, 604 cfg_data[CFG_DEV_MODE].value, 605 cfg_data[CFG_ADAPTER_MODE].value, 606 cfg_data[CFG_TAGS].value, 607 cfg_data[CFG_RESET_DELAY].value); 608 for (i = 0; i < CFG_NUM; i++) 609 { 610 if (cfg_data[i].value < cfg_data[i].min 611 || cfg_data[i].value > cfg_data[i].max) 612 cfg_data[i].value = cfg_data[i].def; 613 } 614 } 615 616 617 618 /* 619 * Mapping from the eeprom delay index value (index into this array) 620 * to the the number of actual seconds that the delay should be for. 621 */ 622 static char __devinitdata eeprom_index_to_delay_map[] = 623 { 1, 3, 5, 10, 16, 30, 60, 120 }; 624 625 626 /** 627 * eeprom_index_to_delay - Take the eeprom delay setting and convert it 628 * into a number of seconds. 629 * 630 * @eeprom: The eeprom structure in which we find the delay index to map. 631 **/ 632 static void __devinit eeprom_index_to_delay(struct NvRamType *eeprom) 633 { 634 eeprom->delay_time = eeprom_index_to_delay_map[eeprom->delay_time]; 635 } 636 637 638 /** 639 * delay_to_eeprom_index - Take a delay in seconds and return the 640 * closest eeprom index which will delay for at least that amount of 641 * seconds. 642 * 643 * @delay: The delay, in seconds, to find the eeprom index for. 644 **/ 645 static int __devinit delay_to_eeprom_index(int delay) 646 { 647 u8 idx = 0; 648 while (idx < 7 && eeprom_index_to_delay_map[idx] < delay) 649 idx++; 650 return idx; 651 } 652 653 654 /** 655 * eeprom_override - Override the eeprom settings, in the provided 656 * eeprom structure, with values that have been set on the command 657 * line. 658 * 659 * @eeprom: The eeprom data to override with command line options. 660 **/ 661 static void __devinit eeprom_override(struct NvRamType *eeprom) 662 { 663 u8 id; 664 665 /* Adapter Settings */ 666 if (cfg_data[CFG_ADAPTER_ID].value != CFG_PARAM_UNSET) 667 eeprom->scsi_id = (u8)cfg_data[CFG_ADAPTER_ID].value; 668 669 if (cfg_data[CFG_ADAPTER_MODE].value != CFG_PARAM_UNSET) 670 eeprom->channel_cfg = (u8)cfg_data[CFG_ADAPTER_MODE].value; 671 672 if (cfg_data[CFG_RESET_DELAY].value != CFG_PARAM_UNSET) 673 eeprom->delay_time = delay_to_eeprom_index( 674 cfg_data[CFG_RESET_DELAY].value); 675 676 if (cfg_data[CFG_TAGS].value != CFG_PARAM_UNSET) 677 eeprom->max_tag = (u8)cfg_data[CFG_TAGS].value; 678 679 /* Device Settings */ 680 for (id = 0; id < DC395x_MAX_SCSI_ID; id++) { 681 if (cfg_data[CFG_DEV_MODE].value != CFG_PARAM_UNSET) 682 eeprom->target[id].cfg0 = 683 (u8)cfg_data[CFG_DEV_MODE].value; 684 685 if (cfg_data[CFG_MAX_SPEED].value != CFG_PARAM_UNSET) 686 eeprom->target[id].period = 687 (u8)cfg_data[CFG_MAX_SPEED].value; 688 689 } 690 } 691 692 693 /*--------------------------------------------------------------------------- 694 ---------------------------------------------------------------------------*/ 695 696 static unsigned int list_size(struct list_head *head) 697 { 698 unsigned int count = 0; 699 struct list_head *pos; 700 list_for_each(pos, head) 701 count++; 702 return count; 703 } 704 705 706 static struct DeviceCtlBlk *dcb_get_next(struct list_head *head, 707 struct DeviceCtlBlk *pos) 708 { 709 int use_next = 0; 710 struct DeviceCtlBlk* next = NULL; 711 struct DeviceCtlBlk* i; 712 713 if (list_empty(head)) 714 return NULL; 715 716 /* find supplied dcb and then select the next one */ 717 list_for_each_entry(i, head, list) 718 if (use_next) { 719 next = i; 720 break; 721 } else if (i == pos) { 722 use_next = 1; 723 } 724 /* if no next one take the head one (ie, wraparound) */ 725 if (!next) 726 list_for_each_entry(i, head, list) { 727 next = i; 728 break; 729 } 730 731 return next; 732 } 733 734 735 static void free_tag(struct DeviceCtlBlk *dcb, struct ScsiReqBlk *srb) 736 { 737 if (srb->tag_number < 255) { 738 dcb->tag_mask &= ~(1 << srb->tag_number); /* free tag mask */ 739 srb->tag_number = 255; 740 } 741 } 742 743 744 /* Find cmd in SRB list */ 745 static inline struct ScsiReqBlk *find_cmd(struct scsi_cmnd *cmd, 746 struct list_head *head) 747 { 748 struct ScsiReqBlk *i; 749 list_for_each_entry(i, head, list) 750 if (i->cmd == cmd) 751 return i; 752 return NULL; 753 } 754 755 756 static struct ScsiReqBlk *srb_get_free(struct AdapterCtlBlk *acb) 757 { 758 struct list_head *head = &acb->srb_free_list; 759 struct ScsiReqBlk *srb = NULL; 760 761 if (!list_empty(head)) { 762 srb = list_entry(head->next, struct ScsiReqBlk, list); 763 list_del(head->next); 764 dprintkdbg(DBG_0, "srb_get_free: srb=%p\n", srb); 765 } 766 return srb; 767 } 768 769 770 static void srb_free_insert(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb) 771 { 772 dprintkdbg(DBG_0, "srb_free_insert: srb=%p\n", srb); 773 list_add_tail(&srb->list, &acb->srb_free_list); 774 } 775 776 777 static void srb_waiting_insert(struct DeviceCtlBlk *dcb, 778 struct ScsiReqBlk *srb) 779 { 780 dprintkdbg(DBG_0, "srb_waiting_insert: (pid#%li) <%02i-%i> srb=%p\n", 781 srb->cmd->pid, dcb->target_id, dcb->target_lun, srb); 782 list_add(&srb->list, &dcb->srb_waiting_list); 783 } 784 785 786 static void srb_waiting_append(struct DeviceCtlBlk *dcb, 787 struct ScsiReqBlk *srb) 788 { 789 dprintkdbg(DBG_0, "srb_waiting_append: (pid#%li) <%02i-%i> srb=%p\n", 790 srb->cmd->pid, dcb->target_id, dcb->target_lun, srb); 791 list_add_tail(&srb->list, &dcb->srb_waiting_list); 792 } 793 794 795 static void srb_going_append(struct DeviceCtlBlk *dcb, struct ScsiReqBlk *srb) 796 { 797 dprintkdbg(DBG_0, "srb_going_append: (pid#%li) <%02i-%i> srb=%p\n", 798 srb->cmd->pid, dcb->target_id, dcb->target_lun, srb); 799 list_add_tail(&srb->list, &dcb->srb_going_list); 800 } 801 802 803 static void srb_going_remove(struct DeviceCtlBlk *dcb, struct ScsiReqBlk *srb) 804 { 805 struct ScsiReqBlk *i; 806 struct ScsiReqBlk *tmp; 807 dprintkdbg(DBG_0, "srb_going_remove: (pid#%li) <%02i-%i> srb=%p\n", 808 srb->cmd->pid, dcb->target_id, dcb->target_lun, srb); 809 810 list_for_each_entry_safe(i, tmp, &dcb->srb_going_list, list) 811 if (i == srb) { 812 list_del(&srb->list); 813 break; 814 } 815 } 816 817 818 static void srb_waiting_remove(struct DeviceCtlBlk *dcb, 819 struct ScsiReqBlk *srb) 820 { 821 struct ScsiReqBlk *i; 822 struct ScsiReqBlk *tmp; 823 dprintkdbg(DBG_0, "srb_waiting_remove: (pid#%li) <%02i-%i> srb=%p\n", 824 srb->cmd->pid, dcb->target_id, dcb->target_lun, srb); 825 826 list_for_each_entry_safe(i, tmp, &dcb->srb_waiting_list, list) 827 if (i == srb) { 828 list_del(&srb->list); 829 break; 830 } 831 } 832 833 834 static void srb_going_to_waiting_move(struct DeviceCtlBlk *dcb, 835 struct ScsiReqBlk *srb) 836 { 837 dprintkdbg(DBG_0, 838 "srb_going_to_waiting_move: (pid#%li) <%02i-%i> srb=%p\n", 839 srb->cmd->pid, dcb->target_id, dcb->target_lun, srb); 840 list_move(&srb->list, &dcb->srb_waiting_list); 841 } 842 843 844 static void srb_waiting_to_going_move(struct DeviceCtlBlk *dcb, 845 struct ScsiReqBlk *srb) 846 { 847 dprintkdbg(DBG_0, 848 "srb_waiting_to_going_move: (pid#%li) <%02i-%i> srb=%p\n", 849 srb->cmd->pid, dcb->target_id, dcb->target_lun, srb); 850 list_move(&srb->list, &dcb->srb_going_list); 851 } 852 853 854 /* Sets the timer to wake us up */ 855 static void waiting_set_timer(struct AdapterCtlBlk *acb, unsigned long to) 856 { 857 if (timer_pending(&acb->waiting_timer)) 858 return; 859 init_timer(&acb->waiting_timer); 860 acb->waiting_timer.function = waiting_timeout; 861 acb->waiting_timer.data = (unsigned long) acb; 862 if (time_before(jiffies + to, acb->scsi_host->last_reset - HZ / 2)) 863 acb->waiting_timer.expires = 864 acb->scsi_host->last_reset - HZ / 2 + 1; 865 else 866 acb->waiting_timer.expires = jiffies + to + 1; 867 add_timer(&acb->waiting_timer); 868 } 869 870 871 /* Send the next command from the waiting list to the bus */ 872 static void waiting_process_next(struct AdapterCtlBlk *acb) 873 { 874 struct DeviceCtlBlk *start = NULL; 875 struct DeviceCtlBlk *pos; 876 struct DeviceCtlBlk *dcb; 877 struct ScsiReqBlk *srb; 878 struct list_head *dcb_list_head = &acb->dcb_list; 879 880 if (acb->active_dcb 881 || (acb->acb_flag & (RESET_DETECT + RESET_DONE + RESET_DEV))) 882 return; 883 884 if (timer_pending(&acb->waiting_timer)) 885 del_timer(&acb->waiting_timer); 886 887 if (list_empty(dcb_list_head)) 888 return; 889 890 /* 891 * Find the starting dcb. Need to find it again in the list 892 * since the list may have changed since we set the ptr to it 893 */ 894 list_for_each_entry(dcb, dcb_list_head, list) 895 if (dcb == acb->dcb_run_robin) { 896 start = dcb; 897 break; 898 } 899 if (!start) { 900 /* This can happen! */ 901 start = list_entry(dcb_list_head->next, typeof(*start), list); 902 acb->dcb_run_robin = start; 903 } 904 905 906 /* 907 * Loop over the dcb, but we start somewhere (potentially) in 908 * the middle of the loop so we need to manully do this. 909 */ 910 pos = start; 911 do { 912 struct list_head *waiting_list_head = &pos->srb_waiting_list; 913 914 /* Make sure, the next another device gets scheduled ... */ 915 acb->dcb_run_robin = dcb_get_next(dcb_list_head, 916 acb->dcb_run_robin); 917 918 if (list_empty(waiting_list_head) || 919 pos->max_command <= list_size(&pos->srb_going_list)) { 920 /* move to next dcb */ 921 pos = dcb_get_next(dcb_list_head, pos); 922 } else { 923 srb = list_entry(waiting_list_head->next, 924 struct ScsiReqBlk, list); 925 926 /* Try to send to the bus */ 927 if (!start_scsi(acb, pos, srb)) 928 srb_waiting_to_going_move(pos, srb); 929 else 930 waiting_set_timer(acb, HZ/50); 931 break; 932 } 933 } while (pos != start); 934 } 935 936 937 /* Wake up waiting queue */ 938 static void waiting_timeout(unsigned long ptr) 939 { 940 unsigned long flags; 941 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)ptr; 942 dprintkdbg(DBG_1, 943 "waiting_timeout: Queue woken up by timer. acb=%p\n", acb); 944 DC395x_LOCK_IO(acb->scsi_host, flags); 945 waiting_process_next(acb); 946 DC395x_UNLOCK_IO(acb->scsi_host, flags); 947 } 948 949 950 /* Get the DCB for a given ID/LUN combination */ 951 static struct DeviceCtlBlk *find_dcb(struct AdapterCtlBlk *acb, u8 id, u8 lun) 952 { 953 return acb->children[id][lun]; 954 } 955 956 957 /* Send SCSI Request Block (srb) to adapter (acb) */ 958 static void send_srb(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb) 959 { 960 struct DeviceCtlBlk *dcb = srb->dcb; 961 962 if (dcb->max_command <= list_size(&dcb->srb_going_list) || 963 acb->active_dcb || 964 (acb->acb_flag & (RESET_DETECT + RESET_DONE + RESET_DEV))) { 965 srb_waiting_append(dcb, srb); 966 waiting_process_next(acb); 967 return; 968 } 969 970 if (!start_scsi(acb, dcb, srb)) 971 srb_going_append(dcb, srb); 972 else { 973 srb_waiting_insert(dcb, srb); 974 waiting_set_timer(acb, HZ / 50); 975 } 976 } 977 978 /* Prepare SRB for being sent to Device DCB w/ command *cmd */ 979 static void build_srb(struct scsi_cmnd *cmd, struct DeviceCtlBlk *dcb, 980 struct ScsiReqBlk *srb) 981 { 982 enum dma_data_direction dir = cmd->sc_data_direction; 983 dprintkdbg(DBG_0, "build_srb: (pid#%li) <%02i-%i>\n", 984 cmd->pid, dcb->target_id, dcb->target_lun); 985 986 srb->dcb = dcb; 987 srb->cmd = cmd; 988 srb->sg_count = 0; 989 srb->total_xfer_length = 0; 990 srb->sg_bus_addr = 0; 991 srb->sg_index = 0; 992 srb->adapter_status = 0; 993 srb->target_status = 0; 994 srb->msg_count = 0; 995 srb->status = 0; 996 srb->flag = 0; 997 srb->state = 0; 998 srb->retry_count = 0; 999 srb->tag_number = TAG_NONE; 1000 srb->scsi_phase = PH_BUS_FREE; /* initial phase */ 1001 srb->end_message = 0; 1002 1003 if (dir == PCI_DMA_NONE || !cmd->request_buffer) { 1004 dprintkdbg(DBG_0, 1005 "build_srb: [0] len=%d buf=%p use_sg=%d !MAP=%08x\n", 1006 cmd->bufflen, cmd->request_buffer, 1007 cmd->use_sg, srb->segment_x[0].address); 1008 } else if (cmd->use_sg) { 1009 int i; 1010 u32 reqlen = cmd->request_bufflen; 1011 struct scatterlist *sl = (struct scatterlist *) 1012 cmd->request_buffer; 1013 struct SGentry *sgp = srb->segment_x; 1014 srb->sg_count = pci_map_sg(dcb->acb->dev, sl, cmd->use_sg, 1015 dir); 1016 dprintkdbg(DBG_0, 1017 "build_srb: [n] len=%d buf=%p use_sg=%d segs=%d\n", 1018 reqlen, cmd->request_buffer, cmd->use_sg, 1019 srb->sg_count); 1020 1021 for (i = 0; i < srb->sg_count; i++) { 1022 u32 busaddr = (u32)sg_dma_address(&sl[i]); 1023 u32 seglen = (u32)sl[i].length; 1024 sgp[i].address = busaddr; 1025 sgp[i].length = seglen; 1026 srb->total_xfer_length += seglen; 1027 } 1028 sgp += srb->sg_count - 1; 1029 1030 /* 1031 * adjust last page if too big as it is allocated 1032 * on even page boundaries 1033 */ 1034 if (srb->total_xfer_length > reqlen) { 1035 sgp->length -= (srb->total_xfer_length - reqlen); 1036 srb->total_xfer_length = reqlen; 1037 } 1038 1039 /* Fixup for WIDE padding - make sure length is even */ 1040 if (dcb->sync_period & WIDE_SYNC && 1041 srb->total_xfer_length % 2) { 1042 srb->total_xfer_length++; 1043 sgp->length++; 1044 } 1045 1046 srb->sg_bus_addr = pci_map_single(dcb->acb->dev, 1047 srb->segment_x, 1048 SEGMENTX_LEN, 1049 PCI_DMA_TODEVICE); 1050 1051 dprintkdbg(DBG_SG, "build_srb: [n] map sg %p->%08x(%05x)\n", 1052 srb->segment_x, srb->sg_bus_addr, SEGMENTX_LEN); 1053 } else { 1054 srb->total_xfer_length = cmd->request_bufflen; 1055 srb->sg_count = 1; 1056 srb->segment_x[0].address = 1057 pci_map_single(dcb->acb->dev, cmd->request_buffer, 1058 srb->total_xfer_length, dir); 1059 1060 /* Fixup for WIDE padding - make sure length is even */ 1061 if (dcb->sync_period & WIDE_SYNC && srb->total_xfer_length % 2) 1062 srb->total_xfer_length++; 1063 1064 srb->segment_x[0].length = srb->total_xfer_length; 1065 1066 dprintkdbg(DBG_0, 1067 "build_srb: [1] len=%d buf=%p use_sg=%d map=%08x\n", 1068 srb->total_xfer_length, cmd->request_buffer, 1069 cmd->use_sg, srb->segment_x[0].address); 1070 } 1071 1072 srb->request_length = srb->total_xfer_length; 1073 } 1074 1075 1076 /** 1077 * dc395x_queue_command - queue scsi command passed from the mid 1078 * layer, invoke 'done' on completion 1079 * 1080 * @cmd: pointer to scsi command object 1081 * @done: function pointer to be invoked on completion 1082 * 1083 * Returns 1 if the adapter (host) is busy, else returns 0. One 1084 * reason for an adapter to be busy is that the number 1085 * of outstanding queued commands is already equal to 1086 * struct Scsi_Host::can_queue . 1087 * 1088 * Required: if struct Scsi_Host::can_queue is ever non-zero 1089 * then this function is required. 1090 * 1091 * Locks: struct Scsi_Host::host_lock held on entry (with "irqsave") 1092 * and is expected to be held on return. 1093 * 1094 **/ 1095 static int dc395x_queue_command(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *)) 1096 { 1097 struct DeviceCtlBlk *dcb; 1098 struct ScsiReqBlk *srb; 1099 struct AdapterCtlBlk *acb = 1100 (struct AdapterCtlBlk *)cmd->device->host->hostdata; 1101 dprintkdbg(DBG_0, "queue_command: (pid#%li) <%02i-%i> cmnd=0x%02x\n", 1102 cmd->pid, cmd->device->id, cmd->device->lun, cmd->cmnd[0]); 1103 1104 /* Assume BAD_TARGET; will be cleared later */ 1105 cmd->result = DID_BAD_TARGET << 16; 1106 1107 /* ignore invalid targets */ 1108 if (cmd->device->id >= acb->scsi_host->max_id || 1109 cmd->device->lun >= acb->scsi_host->max_lun || 1110 cmd->device->lun >31) { 1111 goto complete; 1112 } 1113 1114 /* does the specified lun on the specified device exist */ 1115 if (!(acb->dcb_map[cmd->device->id] & (1 << cmd->device->lun))) { 1116 dprintkl(KERN_INFO, "queue_command: Ignore target <%02i-%i>\n", 1117 cmd->device->id, cmd->device->lun); 1118 goto complete; 1119 } 1120 1121 /* do we have a DCB for the device */ 1122 dcb = find_dcb(acb, cmd->device->id, cmd->device->lun); 1123 if (!dcb) { 1124 /* should never happen */ 1125 dprintkl(KERN_ERR, "queue_command: No such device <%02i-%i>", 1126 cmd->device->id, cmd->device->lun); 1127 goto complete; 1128 } 1129 1130 /* set callback and clear result in the command */ 1131 cmd->scsi_done = done; 1132 cmd->result = 0; 1133 1134 srb = srb_get_free(acb); 1135 if (!srb) 1136 { 1137 /* 1138 * Return 1 since we are unable to queue this command at this 1139 * point in time. 1140 */ 1141 dprintkdbg(DBG_0, "queue_command: No free srb's\n"); 1142 return 1; 1143 } 1144 1145 build_srb(cmd, dcb, srb); 1146 1147 if (!list_empty(&dcb->srb_waiting_list)) { 1148 /* append to waiting queue */ 1149 srb_waiting_append(dcb, srb); 1150 waiting_process_next(acb); 1151 } else { 1152 /* process immediately */ 1153 send_srb(acb, srb); 1154 } 1155 dprintkdbg(DBG_1, "queue_command: (pid#%li) done\n", cmd->pid); 1156 return 0; 1157 1158 complete: 1159 /* 1160 * Complete the command immediatey, and then return 0 to 1161 * indicate that we have handled the command. This is usually 1162 * done when the commad is for things like non existent 1163 * devices. 1164 */ 1165 done(cmd); 1166 return 0; 1167 } 1168 1169 1170 /* 1171 * Return the disk geometry for the given SCSI device. 1172 */ 1173 static int dc395x_bios_param(struct scsi_device *sdev, 1174 struct block_device *bdev, sector_t capacity, int *info) 1175 { 1176 #ifdef CONFIG_SCSI_DC395x_TRMS1040_TRADMAP 1177 int heads, sectors, cylinders; 1178 struct AdapterCtlBlk *acb; 1179 int size = capacity; 1180 1181 dprintkdbg(DBG_0, "dc395x_bios_param..............\n"); 1182 acb = (struct AdapterCtlBlk *)sdev->host->hostdata; 1183 heads = 64; 1184 sectors = 32; 1185 cylinders = size / (heads * sectors); 1186 1187 if ((acb->gmode2 & NAC_GREATER_1G) && (cylinders > 1024)) { 1188 heads = 255; 1189 sectors = 63; 1190 cylinders = size / (heads * sectors); 1191 } 1192 geom[0] = heads; 1193 geom[1] = sectors; 1194 geom[2] = cylinders; 1195 return 0; 1196 #else 1197 return scsicam_bios_param(bdev, capacity, info); 1198 #endif 1199 } 1200 1201 1202 static void dump_register_info(struct AdapterCtlBlk *acb, 1203 struct DeviceCtlBlk *dcb, struct ScsiReqBlk *srb) 1204 { 1205 u16 pstat; 1206 struct pci_dev *dev = acb->dev; 1207 pci_read_config_word(dev, PCI_STATUS, &pstat); 1208 if (!dcb) 1209 dcb = acb->active_dcb; 1210 if (!srb && dcb) 1211 srb = dcb->active_srb; 1212 if (srb) { 1213 if (!srb->cmd) 1214 dprintkl(KERN_INFO, "dump: srb=%p cmd=%p OOOPS!\n", 1215 srb, srb->cmd); 1216 else 1217 dprintkl(KERN_INFO, "dump: srb=%p cmd=%p (pid#%li) " 1218 "cmnd=0x%02x <%02i-%i>\n", 1219 srb, srb->cmd, srb->cmd->pid, 1220 srb->cmd->cmnd[0], srb->cmd->device->id, 1221 srb->cmd->device->lun); 1222 printk(" sglist=%p cnt=%i idx=%i len=%i\n", 1223 srb->segment_x, srb->sg_count, srb->sg_index, 1224 srb->total_xfer_length); 1225 printk(" state=0x%04x status=0x%02x phase=0x%02x (%sconn.)\n", 1226 srb->state, srb->status, srb->scsi_phase, 1227 (acb->active_dcb) ? "" : "not"); 1228 } 1229 dprintkl(KERN_INFO, "dump: SCSI{status=0x%04x fifocnt=0x%02x " 1230 "signals=0x%02x irqstat=0x%02x sync=0x%02x target=0x%02x " 1231 "rselid=0x%02x ctr=0x%08x irqen=0x%02x config=0x%04x " 1232 "config2=0x%02x cmd=0x%02x selto=0x%02x}\n", 1233 DC395x_read16(acb, TRM_S1040_SCSI_STATUS), 1234 DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT), 1235 DC395x_read8(acb, TRM_S1040_SCSI_SIGNAL), 1236 DC395x_read8(acb, TRM_S1040_SCSI_INTSTATUS), 1237 DC395x_read8(acb, TRM_S1040_SCSI_SYNC), 1238 DC395x_read8(acb, TRM_S1040_SCSI_TARGETID), 1239 DC395x_read8(acb, TRM_S1040_SCSI_IDMSG), 1240 DC395x_read32(acb, TRM_S1040_SCSI_COUNTER), 1241 DC395x_read8(acb, TRM_S1040_SCSI_INTEN), 1242 DC395x_read16(acb, TRM_S1040_SCSI_CONFIG0), 1243 DC395x_read8(acb, TRM_S1040_SCSI_CONFIG2), 1244 DC395x_read8(acb, TRM_S1040_SCSI_COMMAND), 1245 DC395x_read8(acb, TRM_S1040_SCSI_TIMEOUT)); 1246 dprintkl(KERN_INFO, "dump: DMA{cmd=0x%04x fifocnt=0x%02x fstat=0x%02x " 1247 "irqstat=0x%02x irqen=0x%02x cfg=0x%04x tctr=0x%08x " 1248 "ctctr=0x%08x addr=0x%08x:0x%08x}\n", 1249 DC395x_read16(acb, TRM_S1040_DMA_COMMAND), 1250 DC395x_read8(acb, TRM_S1040_DMA_FIFOCNT), 1251 DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT), 1252 DC395x_read8(acb, TRM_S1040_DMA_STATUS), 1253 DC395x_read8(acb, TRM_S1040_DMA_INTEN), 1254 DC395x_read16(acb, TRM_S1040_DMA_CONFIG), 1255 DC395x_read32(acb, TRM_S1040_DMA_XCNT), 1256 DC395x_read32(acb, TRM_S1040_DMA_CXCNT), 1257 DC395x_read32(acb, TRM_S1040_DMA_XHIGHADDR), 1258 DC395x_read32(acb, TRM_S1040_DMA_XLOWADDR)); 1259 dprintkl(KERN_INFO, "dump: gen{gctrl=0x%02x gstat=0x%02x gtmr=0x%02x} " 1260 "pci{status=0x%04x}\n", 1261 DC395x_read8(acb, TRM_S1040_GEN_CONTROL), 1262 DC395x_read8(acb, TRM_S1040_GEN_STATUS), 1263 DC395x_read8(acb, TRM_S1040_GEN_TIMER), 1264 pstat); 1265 } 1266 1267 1268 static inline void clear_fifo(struct AdapterCtlBlk *acb, char *txt) 1269 { 1270 #if debug_enabled(DBG_FIFO) 1271 u8 lines = DC395x_read8(acb, TRM_S1040_SCSI_SIGNAL); 1272 u8 fifocnt = DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT); 1273 if (!(fifocnt & 0x40)) 1274 dprintkdbg(DBG_FIFO, 1275 "clear_fifo: (%i bytes) on phase %02x in %s\n", 1276 fifocnt & 0x3f, lines, txt); 1277 #endif 1278 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_CLRFIFO); 1279 } 1280 1281 1282 static void reset_dev_param(struct AdapterCtlBlk *acb) 1283 { 1284 struct DeviceCtlBlk *dcb; 1285 struct NvRamType *eeprom = &acb->eeprom; 1286 dprintkdbg(DBG_0, "reset_dev_param: acb=%p\n", acb); 1287 1288 list_for_each_entry(dcb, &acb->dcb_list, list) { 1289 u8 period_index; 1290 1291 dcb->sync_mode &= ~(SYNC_NEGO_DONE + WIDE_NEGO_DONE); 1292 dcb->sync_period = 0; 1293 dcb->sync_offset = 0; 1294 1295 dcb->dev_mode = eeprom->target[dcb->target_id].cfg0; 1296 period_index = eeprom->target[dcb->target_id].period & 0x07; 1297 dcb->min_nego_period = clock_period[period_index]; 1298 if (!(dcb->dev_mode & NTC_DO_WIDE_NEGO) 1299 || !(acb->config & HCC_WIDE_CARD)) 1300 dcb->sync_mode &= ~WIDE_NEGO_ENABLE; 1301 } 1302 } 1303 1304 1305 /* 1306 * perform a hard reset on the SCSI bus 1307 * @cmd - some command for this host (for fetching hooks) 1308 * Returns: SUCCESS (0x2002) on success, else FAILED (0x2003). 1309 */ 1310 static int __dc395x_eh_bus_reset(struct scsi_cmnd *cmd) 1311 { 1312 struct AdapterCtlBlk *acb = 1313 (struct AdapterCtlBlk *)cmd->device->host->hostdata; 1314 dprintkl(KERN_INFO, 1315 "eh_bus_reset: (pid#%li) target=<%02i-%i> cmd=%p\n", 1316 cmd->pid, cmd->device->id, cmd->device->lun, cmd); 1317 1318 if (timer_pending(&acb->waiting_timer)) 1319 del_timer(&acb->waiting_timer); 1320 1321 /* 1322 * disable interrupt 1323 */ 1324 DC395x_write8(acb, TRM_S1040_DMA_INTEN, 0x00); 1325 DC395x_write8(acb, TRM_S1040_SCSI_INTEN, 0x00); 1326 DC395x_write8(acb, TRM_S1040_SCSI_CONTROL, DO_RSTMODULE); 1327 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, DMARESETMODULE); 1328 1329 reset_scsi_bus(acb); 1330 udelay(500); 1331 1332 /* We may be in serious trouble. Wait some seconds */ 1333 acb->scsi_host->last_reset = 1334 jiffies + 3 * HZ / 2 + 1335 HZ * acb->eeprom.delay_time; 1336 1337 /* 1338 * re-enable interrupt 1339 */ 1340 /* Clear SCSI FIFO */ 1341 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, CLRXFIFO); 1342 clear_fifo(acb, "eh_bus_reset"); 1343 /* Delete pending IRQ */ 1344 DC395x_read8(acb, TRM_S1040_SCSI_INTSTATUS); 1345 set_basic_config(acb); 1346 1347 reset_dev_param(acb); 1348 doing_srb_done(acb, DID_RESET, cmd, 0); 1349 acb->active_dcb = NULL; 1350 acb->acb_flag = 0; /* RESET_DETECT, RESET_DONE ,RESET_DEV */ 1351 waiting_process_next(acb); 1352 1353 return SUCCESS; 1354 } 1355 1356 static int dc395x_eh_bus_reset(struct scsi_cmnd *cmd) 1357 { 1358 int rc; 1359 1360 spin_lock_irq(cmd->device->host->host_lock); 1361 rc = __dc395x_eh_bus_reset(cmd); 1362 spin_unlock_irq(cmd->device->host->host_lock); 1363 1364 return rc; 1365 } 1366 1367 /* 1368 * abort an errant SCSI command 1369 * @cmd - command to be aborted 1370 * Returns: SUCCESS (0x2002) on success, else FAILED (0x2003). 1371 */ 1372 static int dc395x_eh_abort(struct scsi_cmnd *cmd) 1373 { 1374 /* 1375 * Look into our command queues: If it has not been sent already, 1376 * we remove it and return success. Otherwise fail. 1377 */ 1378 struct AdapterCtlBlk *acb = 1379 (struct AdapterCtlBlk *)cmd->device->host->hostdata; 1380 struct DeviceCtlBlk *dcb; 1381 struct ScsiReqBlk *srb; 1382 dprintkl(KERN_INFO, "eh_abort: (pid#%li) target=<%02i-%i> cmd=%p\n", 1383 cmd->pid, cmd->device->id, cmd->device->lun, cmd); 1384 1385 dcb = find_dcb(acb, cmd->device->id, cmd->device->lun); 1386 if (!dcb) { 1387 dprintkl(KERN_DEBUG, "eh_abort: No such device\n"); 1388 return FAILED; 1389 } 1390 1391 srb = find_cmd(cmd, &dcb->srb_waiting_list); 1392 if (srb) { 1393 srb_waiting_remove(dcb, srb); 1394 pci_unmap_srb_sense(acb, srb); 1395 pci_unmap_srb(acb, srb); 1396 free_tag(dcb, srb); 1397 srb_free_insert(acb, srb); 1398 dprintkl(KERN_DEBUG, "eh_abort: Command was waiting\n"); 1399 cmd->result = DID_ABORT << 16; 1400 return SUCCESS; 1401 } 1402 srb = find_cmd(cmd, &dcb->srb_going_list); 1403 if (srb) { 1404 dprintkl(KERN_DEBUG, "eh_abort: Command in progress\n"); 1405 /* XXX: Should abort the command here */ 1406 } else { 1407 dprintkl(KERN_DEBUG, "eh_abort: Command not found\n"); 1408 } 1409 return FAILED; 1410 } 1411 1412 1413 /* SDTR */ 1414 static void build_sdtr(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 1415 struct ScsiReqBlk *srb) 1416 { 1417 u8 *ptr = srb->msgout_buf + srb->msg_count; 1418 if (srb->msg_count > 1) { 1419 dprintkl(KERN_INFO, 1420 "build_sdtr: msgout_buf BUSY (%i: %02x %02x)\n", 1421 srb->msg_count, srb->msgout_buf[0], 1422 srb->msgout_buf[1]); 1423 return; 1424 } 1425 if (!(dcb->dev_mode & NTC_DO_SYNC_NEGO)) { 1426 dcb->sync_offset = 0; 1427 dcb->min_nego_period = 200 >> 2; 1428 } else if (dcb->sync_offset == 0) 1429 dcb->sync_offset = SYNC_NEGO_OFFSET; 1430 1431 *ptr++ = MSG_EXTENDED; /* (01h) */ 1432 *ptr++ = 3; /* length */ 1433 *ptr++ = EXTENDED_SDTR; /* (01h) */ 1434 *ptr++ = dcb->min_nego_period; /* Transfer period (in 4ns) */ 1435 *ptr++ = dcb->sync_offset; /* Transfer period (max. REQ/ACK dist) */ 1436 srb->msg_count += 5; 1437 srb->state |= SRB_DO_SYNC_NEGO; 1438 } 1439 1440 1441 /* WDTR */ 1442 static void build_wdtr(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 1443 struct ScsiReqBlk *srb) 1444 { 1445 u8 wide = ((dcb->dev_mode & NTC_DO_WIDE_NEGO) & 1446 (acb->config & HCC_WIDE_CARD)) ? 1 : 0; 1447 u8 *ptr = srb->msgout_buf + srb->msg_count; 1448 if (srb->msg_count > 1) { 1449 dprintkl(KERN_INFO, 1450 "build_wdtr: msgout_buf BUSY (%i: %02x %02x)\n", 1451 srb->msg_count, srb->msgout_buf[0], 1452 srb->msgout_buf[1]); 1453 return; 1454 } 1455 *ptr++ = MSG_EXTENDED; /* (01h) */ 1456 *ptr++ = 2; /* length */ 1457 *ptr++ = EXTENDED_WDTR; /* (03h) */ 1458 *ptr++ = wide; 1459 srb->msg_count += 4; 1460 srb->state |= SRB_DO_WIDE_NEGO; 1461 } 1462 1463 1464 #if 0 1465 /* Timer to work around chip flaw: When selecting and the bus is 1466 * busy, we sometimes miss a Selection timeout IRQ */ 1467 void selection_timeout_missed(unsigned long ptr); 1468 /* Sets the timer to wake us up */ 1469 static void selto_timer(struct AdapterCtlBlk *acb) 1470 { 1471 if (timer_pending(&acb->selto_timer)) 1472 return; 1473 acb->selto_timer.function = selection_timeout_missed; 1474 acb->selto_timer.data = (unsigned long) acb; 1475 if (time_before 1476 (jiffies + HZ, acb->scsi_host->last_reset + HZ / 2)) 1477 acb->selto_timer.expires = 1478 acb->scsi_host->last_reset + HZ / 2 + 1; 1479 else 1480 acb->selto_timer.expires = jiffies + HZ + 1; 1481 add_timer(&acb->selto_timer); 1482 } 1483 1484 1485 void selection_timeout_missed(unsigned long ptr) 1486 { 1487 unsigned long flags; 1488 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)ptr; 1489 struct ScsiReqBlk *srb; 1490 dprintkl(KERN_DEBUG, "Chip forgot to produce SelTO IRQ!\n"); 1491 if (!acb->active_dcb || !acb->active_dcb->active_srb) { 1492 dprintkl(KERN_DEBUG, "... but no cmd pending? Oops!\n"); 1493 return; 1494 } 1495 DC395x_LOCK_IO(acb->scsi_host, flags); 1496 srb = acb->active_dcb->active_srb; 1497 disconnect(acb); 1498 DC395x_UNLOCK_IO(acb->scsi_host, flags); 1499 } 1500 #endif 1501 1502 1503 static u8 start_scsi(struct AdapterCtlBlk* acb, struct DeviceCtlBlk* dcb, 1504 struct ScsiReqBlk* srb) 1505 { 1506 u16 s_stat2, return_code; 1507 u8 s_stat, scsicommand, i, identify_message; 1508 u8 *ptr; 1509 dprintkdbg(DBG_0, "start_scsi: (pid#%li) <%02i-%i> srb=%p\n", 1510 srb->cmd->pid, dcb->target_id, dcb->target_lun, srb); 1511 1512 srb->tag_number = TAG_NONE; /* acb->tag_max_num: had error read in eeprom */ 1513 1514 s_stat = DC395x_read8(acb, TRM_S1040_SCSI_SIGNAL); 1515 s_stat2 = 0; 1516 s_stat2 = DC395x_read16(acb, TRM_S1040_SCSI_STATUS); 1517 #if 1 1518 if (s_stat & 0x20 /* s_stat2 & 0x02000 */ ) { 1519 dprintkdbg(DBG_KG, "start_scsi: (pid#%li) BUSY %02x %04x\n", 1520 srb->cmd->pid, s_stat, s_stat2); 1521 /* 1522 * Try anyway? 1523 * 1524 * We could, BUT: Sometimes the TRM_S1040 misses to produce a Selection 1525 * Timeout, a Disconnect or a Reselction IRQ, so we would be screwed! 1526 * (This is likely to be a bug in the hardware. Obviously, most people 1527 * only have one initiator per SCSI bus.) 1528 * Instead let this fail and have the timer make sure the command is 1529 * tried again after a short time 1530 */ 1531 /*selto_timer (acb); */ 1532 return 1; 1533 } 1534 #endif 1535 if (acb->active_dcb) { 1536 dprintkl(KERN_DEBUG, "start_scsi: (pid#%li) Attempt to start a" 1537 "command while another command (pid#%li) is active.", 1538 srb->cmd->pid, 1539 acb->active_dcb->active_srb ? 1540 acb->active_dcb->active_srb->cmd->pid : 0); 1541 return 1; 1542 } 1543 if (DC395x_read16(acb, TRM_S1040_SCSI_STATUS) & SCSIINTERRUPT) { 1544 dprintkdbg(DBG_KG, "start_scsi: (pid#%li) Failed (busy)\n", 1545 srb->cmd->pid); 1546 return 1; 1547 } 1548 /* Allow starting of SCSI commands half a second before we allow the mid-level 1549 * to queue them again after a reset */ 1550 if (time_before(jiffies, acb->scsi_host->last_reset - HZ / 2)) { 1551 dprintkdbg(DBG_KG, "start_scsi: Refuse cmds (reset wait)\n"); 1552 return 1; 1553 } 1554 1555 /* Flush FIFO */ 1556 clear_fifo(acb, "start_scsi"); 1557 DC395x_write8(acb, TRM_S1040_SCSI_HOSTID, acb->scsi_host->this_id); 1558 DC395x_write8(acb, TRM_S1040_SCSI_TARGETID, dcb->target_id); 1559 DC395x_write8(acb, TRM_S1040_SCSI_SYNC, dcb->sync_period); 1560 DC395x_write8(acb, TRM_S1040_SCSI_OFFSET, dcb->sync_offset); 1561 srb->scsi_phase = PH_BUS_FREE; /* initial phase */ 1562 1563 identify_message = dcb->identify_msg; 1564 /*DC395x_TRM_write8(TRM_S1040_SCSI_IDMSG, identify_message); */ 1565 /* Don't allow disconnection for AUTO_REQSENSE: Cont.All.Cond.! */ 1566 if (srb->flag & AUTO_REQSENSE) 1567 identify_message &= 0xBF; 1568 1569 if (((srb->cmd->cmnd[0] == INQUIRY) 1570 || (srb->cmd->cmnd[0] == REQUEST_SENSE) 1571 || (srb->flag & AUTO_REQSENSE)) 1572 && (((dcb->sync_mode & WIDE_NEGO_ENABLE) 1573 && !(dcb->sync_mode & WIDE_NEGO_DONE)) 1574 || ((dcb->sync_mode & SYNC_NEGO_ENABLE) 1575 && !(dcb->sync_mode & SYNC_NEGO_DONE))) 1576 && (dcb->target_lun == 0)) { 1577 srb->msgout_buf[0] = identify_message; 1578 srb->msg_count = 1; 1579 scsicommand = SCMD_SEL_ATNSTOP; 1580 srb->state = SRB_MSGOUT; 1581 #ifndef SYNC_FIRST 1582 if (dcb->sync_mode & WIDE_NEGO_ENABLE 1583 && dcb->inquiry7 & SCSI_INQ_WBUS16) { 1584 build_wdtr(acb, dcb, srb); 1585 goto no_cmd; 1586 } 1587 #endif 1588 if (dcb->sync_mode & SYNC_NEGO_ENABLE 1589 && dcb->inquiry7 & SCSI_INQ_SYNC) { 1590 build_sdtr(acb, dcb, srb); 1591 goto no_cmd; 1592 } 1593 if (dcb->sync_mode & WIDE_NEGO_ENABLE 1594 && dcb->inquiry7 & SCSI_INQ_WBUS16) { 1595 build_wdtr(acb, dcb, srb); 1596 goto no_cmd; 1597 } 1598 srb->msg_count = 0; 1599 } 1600 /* Send identify message */ 1601 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, identify_message); 1602 1603 scsicommand = SCMD_SEL_ATN; 1604 srb->state = SRB_START_; 1605 #ifndef DC395x_NO_TAGQ 1606 if ((dcb->sync_mode & EN_TAG_QUEUEING) 1607 && (identify_message & 0xC0)) { 1608 /* Send Tag message */ 1609 u32 tag_mask = 1; 1610 u8 tag_number = 0; 1611 while (tag_mask & dcb->tag_mask 1612 && tag_number <= dcb->max_command) { 1613 tag_mask = tag_mask << 1; 1614 tag_number++; 1615 } 1616 if (tag_number >= dcb->max_command) { 1617 dprintkl(KERN_WARNING, "start_scsi: (pid#%li) " 1618 "Out of tags target=<%02i-%i>)\n", 1619 srb->cmd->pid, srb->cmd->device->id, 1620 srb->cmd->device->lun); 1621 srb->state = SRB_READY; 1622 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, 1623 DO_HWRESELECT); 1624 return 1; 1625 } 1626 /* Send Tag id */ 1627 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, MSG_SIMPLE_QTAG); 1628 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, tag_number); 1629 dcb->tag_mask |= tag_mask; 1630 srb->tag_number = tag_number; 1631 scsicommand = SCMD_SEL_ATN3; 1632 srb->state = SRB_START_; 1633 } 1634 #endif 1635 /*polling:*/ 1636 /* Send CDB ..command block ......... */ 1637 dprintkdbg(DBG_KG, "start_scsi: (pid#%li) <%02i-%i> cmnd=0x%02x tag=%i\n", 1638 srb->cmd->pid, srb->cmd->device->id, srb->cmd->device->lun, 1639 srb->cmd->cmnd[0], srb->tag_number); 1640 if (srb->flag & AUTO_REQSENSE) { 1641 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, REQUEST_SENSE); 1642 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, (dcb->target_lun << 5)); 1643 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 0); 1644 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 0); 1645 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 1646 sizeof(srb->cmd->sense_buffer)); 1647 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 0); 1648 } else { 1649 ptr = (u8 *)srb->cmd->cmnd; 1650 for (i = 0; i < srb->cmd->cmd_len; i++) 1651 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, *ptr++); 1652 } 1653 no_cmd: 1654 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, 1655 DO_HWRESELECT | DO_DATALATCH); 1656 if (DC395x_read16(acb, TRM_S1040_SCSI_STATUS) & SCSIINTERRUPT) { 1657 /* 1658 * If start_scsi return 1: 1659 * we caught an interrupt (must be reset or reselection ... ) 1660 * : Let's process it first! 1661 */ 1662 dprintkdbg(DBG_0, "start_scsi: (pid#%li) <%02i-%i> Failed - busy\n", 1663 srb->cmd->pid, dcb->target_id, dcb->target_lun); 1664 srb->state = SRB_READY; 1665 free_tag(dcb, srb); 1666 srb->msg_count = 0; 1667 return_code = 1; 1668 /* This IRQ should NOT get lost, as we did not acknowledge it */ 1669 } else { 1670 /* 1671 * If start_scsi returns 0: 1672 * we know that the SCSI processor is free 1673 */ 1674 srb->scsi_phase = PH_BUS_FREE; /* initial phase */ 1675 dcb->active_srb = srb; 1676 acb->active_dcb = dcb; 1677 return_code = 0; 1678 /* it's important for atn stop */ 1679 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, 1680 DO_DATALATCH | DO_HWRESELECT); 1681 /* SCSI command */ 1682 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, scsicommand); 1683 } 1684 return return_code; 1685 } 1686 1687 1688 #define DC395x_ENABLE_MSGOUT \ 1689 DC395x_write16 (acb, TRM_S1040_SCSI_CONTROL, DO_SETATN); \ 1690 srb->state |= SRB_MSGOUT 1691 1692 1693 /* abort command */ 1694 static inline void enable_msgout_abort(struct AdapterCtlBlk *acb, 1695 struct ScsiReqBlk *srb) 1696 { 1697 srb->msgout_buf[0] = ABORT; 1698 srb->msg_count = 1; 1699 DC395x_ENABLE_MSGOUT; 1700 srb->state &= ~SRB_MSGIN; 1701 srb->state |= SRB_MSGOUT; 1702 } 1703 1704 1705 /** 1706 * dc395x_handle_interrupt - Handle an interrupt that has been confirmed to 1707 * have been triggered for this card. 1708 * 1709 * @acb: a pointer to the adpter control block 1710 * @scsi_status: the status return when we checked the card 1711 **/ 1712 static void dc395x_handle_interrupt(struct AdapterCtlBlk *acb, 1713 u16 scsi_status) 1714 { 1715 struct DeviceCtlBlk *dcb; 1716 struct ScsiReqBlk *srb; 1717 u16 phase; 1718 u8 scsi_intstatus; 1719 unsigned long flags; 1720 void (*dc395x_statev)(struct AdapterCtlBlk *, struct ScsiReqBlk *, 1721 u16 *); 1722 1723 DC395x_LOCK_IO(acb->scsi_host, flags); 1724 1725 /* This acknowledges the IRQ */ 1726 scsi_intstatus = DC395x_read8(acb, TRM_S1040_SCSI_INTSTATUS); 1727 if ((scsi_status & 0x2007) == 0x2002) 1728 dprintkl(KERN_DEBUG, 1729 "COP after COP completed? %04x\n", scsi_status); 1730 if (debug_enabled(DBG_KG)) { 1731 if (scsi_intstatus & INT_SELTIMEOUT) 1732 dprintkdbg(DBG_KG, "handle_interrupt: Selection timeout\n"); 1733 } 1734 /*dprintkl(KERN_DEBUG, "handle_interrupt: intstatus = 0x%02x ", scsi_intstatus); */ 1735 1736 if (timer_pending(&acb->selto_timer)) 1737 del_timer(&acb->selto_timer); 1738 1739 if (scsi_intstatus & (INT_SELTIMEOUT | INT_DISCONNECT)) { 1740 disconnect(acb); /* bus free interrupt */ 1741 goto out_unlock; 1742 } 1743 if (scsi_intstatus & INT_RESELECTED) { 1744 reselect(acb); 1745 goto out_unlock; 1746 } 1747 if (scsi_intstatus & INT_SELECT) { 1748 dprintkl(KERN_INFO, "Host does not support target mode!\n"); 1749 goto out_unlock; 1750 } 1751 if (scsi_intstatus & INT_SCSIRESET) { 1752 scsi_reset_detect(acb); 1753 goto out_unlock; 1754 } 1755 if (scsi_intstatus & (INT_BUSSERVICE | INT_CMDDONE)) { 1756 dcb = acb->active_dcb; 1757 if (!dcb) { 1758 dprintkl(KERN_DEBUG, 1759 "Oops: BusService (%04x %02x) w/o ActiveDCB!\n", 1760 scsi_status, scsi_intstatus); 1761 goto out_unlock; 1762 } 1763 srb = dcb->active_srb; 1764 if (dcb->flag & ABORT_DEV_) { 1765 dprintkdbg(DBG_0, "MsgOut Abort Device.....\n"); 1766 enable_msgout_abort(acb, srb); 1767 } 1768 1769 /* software sequential machine */ 1770 phase = (u16)srb->scsi_phase; 1771 1772 /* 1773 * 62037 or 62137 1774 * call dc395x_scsi_phase0[]... "phase entry" 1775 * handle every phase before start transfer 1776 */ 1777 /* data_out_phase0, phase:0 */ 1778 /* data_in_phase0, phase:1 */ 1779 /* command_phase0, phase:2 */ 1780 /* status_phase0, phase:3 */ 1781 /* nop0, phase:4 PH_BUS_FREE .. initial phase */ 1782 /* nop0, phase:5 PH_BUS_FREE .. initial phase */ 1783 /* msgout_phase0, phase:6 */ 1784 /* msgin_phase0, phase:7 */ 1785 dc395x_statev = dc395x_scsi_phase0[phase]; 1786 dc395x_statev(acb, srb, &scsi_status); 1787 1788 /* 1789 * if there were any exception occured scsi_status 1790 * will be modify to bus free phase new scsi_status 1791 * transfer out from ... previous dc395x_statev 1792 */ 1793 srb->scsi_phase = scsi_status & PHASEMASK; 1794 phase = (u16)scsi_status & PHASEMASK; 1795 1796 /* 1797 * call dc395x_scsi_phase1[]... "phase entry" handle 1798 * every phase to do transfer 1799 */ 1800 /* data_out_phase1, phase:0 */ 1801 /* data_in_phase1, phase:1 */ 1802 /* command_phase1, phase:2 */ 1803 /* status_phase1, phase:3 */ 1804 /* nop1, phase:4 PH_BUS_FREE .. initial phase */ 1805 /* nop1, phase:5 PH_BUS_FREE .. initial phase */ 1806 /* msgout_phase1, phase:6 */ 1807 /* msgin_phase1, phase:7 */ 1808 dc395x_statev = dc395x_scsi_phase1[phase]; 1809 dc395x_statev(acb, srb, &scsi_status); 1810 } 1811 out_unlock: 1812 DC395x_UNLOCK_IO(acb->scsi_host, flags); 1813 } 1814 1815 1816 static irqreturn_t dc395x_interrupt(int irq, void *dev_id, 1817 struct pt_regs *regs) 1818 { 1819 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)dev_id; 1820 u16 scsi_status; 1821 u8 dma_status; 1822 irqreturn_t handled = IRQ_NONE; 1823 1824 /* 1825 * Check for pending interupt 1826 */ 1827 scsi_status = DC395x_read16(acb, TRM_S1040_SCSI_STATUS); 1828 dma_status = DC395x_read8(acb, TRM_S1040_DMA_STATUS); 1829 if (scsi_status & SCSIINTERRUPT) { 1830 /* interupt pending - let's process it! */ 1831 dc395x_handle_interrupt(acb, scsi_status); 1832 handled = IRQ_HANDLED; 1833 } 1834 else if (dma_status & 0x20) { 1835 /* Error from the DMA engine */ 1836 dprintkl(KERN_INFO, "Interrupt from DMA engine: 0x%02x!\n", dma_status); 1837 #if 0 1838 dprintkl(KERN_INFO, "This means DMA error! Try to handle ...\n"); 1839 if (acb->active_dcb) { 1840 acb->active_dcb-> flag |= ABORT_DEV_; 1841 if (acb->active_dcb->active_srb) 1842 enable_msgout_abort(acb, acb->active_dcb->active_srb); 1843 } 1844 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, ABORTXFER | CLRXFIFO); 1845 #else 1846 dprintkl(KERN_INFO, "Ignoring DMA error (probably a bad thing) ...\n"); 1847 acb = NULL; 1848 #endif 1849 handled = IRQ_HANDLED; 1850 } 1851 1852 return handled; 1853 } 1854 1855 1856 static void msgout_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 1857 u16 *pscsi_status) 1858 { 1859 dprintkdbg(DBG_0, "msgout_phase0: (pid#%li)\n", srb->cmd->pid); 1860 if (srb->state & (SRB_UNEXPECT_RESEL + SRB_ABORT_SENT)) 1861 *pscsi_status = PH_BUS_FREE; /*.. initial phase */ 1862 1863 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 1864 srb->state &= ~SRB_MSGOUT; 1865 } 1866 1867 1868 static void msgout_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 1869 u16 *pscsi_status) 1870 { 1871 u16 i; 1872 u8 *ptr; 1873 dprintkdbg(DBG_0, "msgout_phase1: (pid#%li)\n", srb->cmd->pid); 1874 1875 clear_fifo(acb, "msgout_phase1"); 1876 if (!(srb->state & SRB_MSGOUT)) { 1877 srb->state |= SRB_MSGOUT; 1878 dprintkl(KERN_DEBUG, 1879 "msgout_phase1: (pid#%li) Phase unexpected\n", 1880 srb->cmd->pid); /* So what ? */ 1881 } 1882 if (!srb->msg_count) { 1883 dprintkdbg(DBG_0, "msgout_phase1: (pid#%li) NOP msg\n", 1884 srb->cmd->pid); 1885 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, MSG_NOP); 1886 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 1887 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_FIFO_OUT); 1888 return; 1889 } 1890 ptr = (u8 *)srb->msgout_buf; 1891 for (i = 0; i < srb->msg_count; i++) 1892 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, *ptr++); 1893 srb->msg_count = 0; 1894 if (srb->msgout_buf[0] == MSG_ABORT) 1895 srb->state = SRB_ABORT_SENT; 1896 1897 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_FIFO_OUT); 1898 } 1899 1900 1901 static void command_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 1902 u16 *pscsi_status) 1903 { 1904 dprintkdbg(DBG_0, "command_phase0: (pid#%li)\n", srb->cmd->pid); 1905 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); 1906 } 1907 1908 1909 static void command_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 1910 u16 *pscsi_status) 1911 { 1912 struct DeviceCtlBlk *dcb; 1913 u8 *ptr; 1914 u16 i; 1915 dprintkdbg(DBG_0, "command_phase1: (pid#%li)\n", srb->cmd->pid); 1916 1917 clear_fifo(acb, "command_phase1"); 1918 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_CLRATN); 1919 if (!(srb->flag & AUTO_REQSENSE)) { 1920 ptr = (u8 *)srb->cmd->cmnd; 1921 for (i = 0; i < srb->cmd->cmd_len; i++) { 1922 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, *ptr); 1923 ptr++; 1924 } 1925 } else { 1926 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, REQUEST_SENSE); 1927 dcb = acb->active_dcb; 1928 /* target id */ 1929 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, (dcb->target_lun << 5)); 1930 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 0); 1931 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 0); 1932 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 1933 sizeof(srb->cmd->sense_buffer)); 1934 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 0); 1935 } 1936 srb->state |= SRB_COMMAND; 1937 /* it's important for atn stop */ 1938 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); 1939 /* SCSI command */ 1940 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_FIFO_OUT); 1941 } 1942 1943 1944 /* 1945 * Verify that the remaining space in the hw sg lists is the same as 1946 * the count of remaining bytes in srb->total_xfer_length 1947 */ 1948 static void sg_verify_length(struct ScsiReqBlk *srb) 1949 { 1950 if (debug_enabled(DBG_SG)) { 1951 unsigned len = 0; 1952 unsigned idx = srb->sg_index; 1953 struct SGentry *psge = srb->segment_x + idx; 1954 for (; idx < srb->sg_count; psge++, idx++) 1955 len += psge->length; 1956 if (len != srb->total_xfer_length) 1957 dprintkdbg(DBG_SG, 1958 "Inconsistent SRB S/G lengths (Tot=%i, Count=%i) !!\n", 1959 srb->total_xfer_length, len); 1960 } 1961 } 1962 1963 1964 /* 1965 * Compute the next Scatter Gather list index and adjust its length 1966 * and address if necessary 1967 */ 1968 static void sg_update_list(struct ScsiReqBlk *srb, u32 left) 1969 { 1970 u8 idx; 1971 u32 xferred = srb->total_xfer_length - left; /* bytes transfered */ 1972 struct SGentry *psge = srb->segment_x + srb->sg_index; 1973 1974 dprintkdbg(DBG_0, 1975 "sg_update_list: Transfered %i of %i bytes, %i remain\n", 1976 xferred, srb->total_xfer_length, left); 1977 if (xferred == 0) { 1978 /* nothing to update since we did not transfer any data */ 1979 return; 1980 } 1981 1982 sg_verify_length(srb); 1983 srb->total_xfer_length = left; /* update remaining count */ 1984 for (idx = srb->sg_index; idx < srb->sg_count; idx++) { 1985 if (xferred >= psge->length) { 1986 /* Complete SG entries done */ 1987 xferred -= psge->length; 1988 } else { 1989 /* Partial SG entry done */ 1990 psge->length -= xferred; 1991 psge->address += xferred; 1992 srb->sg_index = idx; 1993 pci_dma_sync_single_for_device(srb->dcb-> 1994 acb->dev, 1995 srb->sg_bus_addr, 1996 SEGMENTX_LEN, 1997 PCI_DMA_TODEVICE); 1998 break; 1999 } 2000 psge++; 2001 } 2002 sg_verify_length(srb); 2003 } 2004 2005 2006 /* 2007 * We have transfered a single byte (PIO mode?) and need to update 2008 * the count of bytes remaining (total_xfer_length) and update the sg 2009 * entry to either point to next byte in the current sg entry, or of 2010 * already at the end to point to the start of the next sg entry 2011 */ 2012 static void sg_subtract_one(struct ScsiReqBlk *srb) 2013 { 2014 sg_update_list(srb, srb->total_xfer_length - 1); 2015 } 2016 2017 2018 /* 2019 * cleanup_after_transfer 2020 * 2021 * Makes sure, DMA and SCSI engine are empty, after the transfer has finished 2022 * KG: Currently called from StatusPhase1 () 2023 * Should probably also be called from other places 2024 * Best might be to call it in DataXXPhase0, if new phase will differ 2025 */ 2026 static void cleanup_after_transfer(struct AdapterCtlBlk *acb, 2027 struct ScsiReqBlk *srb) 2028 { 2029 /*DC395x_write8 (TRM_S1040_DMA_STATUS, FORCEDMACOMP); */ 2030 if (DC395x_read16(acb, TRM_S1040_DMA_COMMAND) & 0x0001) { /* read */ 2031 if (!(DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT) & 0x40)) 2032 clear_fifo(acb, "cleanup/in"); 2033 if (!(DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT) & 0x80)) 2034 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, CLRXFIFO); 2035 } else { /* write */ 2036 if (!(DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT) & 0x80)) 2037 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, CLRXFIFO); 2038 if (!(DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT) & 0x40)) 2039 clear_fifo(acb, "cleanup/out"); 2040 } 2041 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); 2042 } 2043 2044 2045 /* 2046 * Those no of bytes will be transfered w/ PIO through the SCSI FIFO 2047 * Seems to be needed for unknown reasons; could be a hardware bug :-( 2048 */ 2049 #define DC395x_LASTPIO 4 2050 2051 2052 static void data_out_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2053 u16 *pscsi_status) 2054 { 2055 struct DeviceCtlBlk *dcb = srb->dcb; 2056 u16 scsi_status = *pscsi_status; 2057 u32 d_left_counter = 0; 2058 dprintkdbg(DBG_0, "data_out_phase0: (pid#%li) <%02i-%i>\n", 2059 srb->cmd->pid, srb->cmd->device->id, srb->cmd->device->lun); 2060 2061 /* 2062 * KG: We need to drain the buffers before we draw any conclusions! 2063 * This means telling the DMA to push the rest into SCSI, telling 2064 * SCSI to push the rest to the bus. 2065 * However, the device might have been the one to stop us (phase 2066 * change), and the data in transit just needs to be accounted so 2067 * it can be retransmitted.) 2068 */ 2069 /* 2070 * KG: Stop DMA engine pushing more data into the SCSI FIFO 2071 * If we need more data, the DMA SG list will be freshly set up, anyway 2072 */ 2073 dprintkdbg(DBG_PIO, "data_out_phase0: " 2074 "DMA{fifocnt=0x%02x fifostat=0x%02x} " 2075 "SCSI{fifocnt=0x%02x cnt=0x%06x status=0x%04x} total=0x%06x\n", 2076 DC395x_read8(acb, TRM_S1040_DMA_FIFOCNT), 2077 DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT), 2078 DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT), 2079 DC395x_read32(acb, TRM_S1040_SCSI_COUNTER), scsi_status, 2080 srb->total_xfer_length); 2081 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, STOPDMAXFER | CLRXFIFO); 2082 2083 if (!(srb->state & SRB_XFERPAD)) { 2084 if (scsi_status & PARITYERROR) 2085 srb->status |= PARITY_ERROR; 2086 2087 /* 2088 * KG: Right, we can't just rely on the SCSI_COUNTER, because this 2089 * is the no of bytes it got from the DMA engine not the no it 2090 * transferred successfully to the device. (And the difference could 2091 * be as much as the FIFO size, I guess ...) 2092 */ 2093 if (!(scsi_status & SCSIXFERDONE)) { 2094 /* 2095 * when data transfer from DMA FIFO to SCSI FIFO 2096 * if there was some data left in SCSI FIFO 2097 */ 2098 d_left_counter = 2099 (u32)(DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT) & 2100 0x1F); 2101 if (dcb->sync_period & WIDE_SYNC) 2102 d_left_counter <<= 1; 2103 2104 dprintkdbg(DBG_KG, "data_out_phase0: FIFO contains %i %s\n" 2105 "SCSI{fifocnt=0x%02x cnt=0x%08x} " 2106 "DMA{fifocnt=0x%04x cnt=0x%02x ctr=0x%08x}\n", 2107 DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT), 2108 (dcb->sync_period & WIDE_SYNC) ? "words" : "bytes", 2109 DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT), 2110 DC395x_read32(acb, TRM_S1040_SCSI_COUNTER), 2111 DC395x_read8(acb, TRM_S1040_DMA_FIFOCNT), 2112 DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT), 2113 DC395x_read32(acb, TRM_S1040_DMA_CXCNT)); 2114 } 2115 /* 2116 * calculate all the residue data that not yet tranfered 2117 * SCSI transfer counter + left in SCSI FIFO data 2118 * 2119 * .....TRM_S1040_SCSI_COUNTER (24bits) 2120 * The counter always decrement by one for every SCSI byte transfer. 2121 * .....TRM_S1040_SCSI_FIFOCNT ( 5bits) 2122 * The counter is SCSI FIFO offset counter (in units of bytes or! words) 2123 */ 2124 if (srb->total_xfer_length > DC395x_LASTPIO) 2125 d_left_counter += 2126 DC395x_read32(acb, TRM_S1040_SCSI_COUNTER); 2127 2128 /* Is this a good idea? */ 2129 /*clear_fifo(acb, "DOP1"); */ 2130 /* KG: What is this supposed to be useful for? WIDE padding stuff? */ 2131 if (d_left_counter == 1 && dcb->sync_period & WIDE_SYNC 2132 && srb->cmd->request_bufflen % 2) { 2133 d_left_counter = 0; 2134 dprintkl(KERN_INFO, 2135 "data_out_phase0: Discard 1 byte (0x%02x)\n", 2136 scsi_status); 2137 } 2138 /* 2139 * KG: Oops again. Same thinko as above: The SCSI might have been 2140 * faster than the DMA engine, so that it ran out of data. 2141 * In that case, we have to do just nothing! 2142 * But: Why the interrupt: No phase change. No XFERCNT_2_ZERO. Or? 2143 */ 2144 /* 2145 * KG: This is nonsense: We have been WRITING data to the bus 2146 * If the SCSI engine has no bytes left, how should the DMA engine? 2147 */ 2148 if (d_left_counter == 0) { 2149 srb->total_xfer_length = 0; 2150 } else { 2151 /* 2152 * if transfer not yet complete 2153 * there were some data residue in SCSI FIFO or 2154 * SCSI transfer counter not empty 2155 */ 2156 long oldxferred = 2157 srb->total_xfer_length - d_left_counter; 2158 const int diff = 2159 (dcb->sync_period & WIDE_SYNC) ? 2 : 1; 2160 sg_update_list(srb, d_left_counter); 2161 /* KG: Most ugly hack! Apparently, this works around a chip bug */ 2162 if ((srb->segment_x[srb->sg_index].length == 2163 diff && srb->cmd->use_sg) 2164 || ((oldxferred & ~PAGE_MASK) == 2165 (PAGE_SIZE - diff)) 2166 ) { 2167 dprintkl(KERN_INFO, "data_out_phase0: " 2168 "Work around chip bug (%i)?\n", diff); 2169 d_left_counter = 2170 srb->total_xfer_length - diff; 2171 sg_update_list(srb, d_left_counter); 2172 /*srb->total_xfer_length -= diff; */ 2173 /*srb->virt_addr += diff; */ 2174 /*if (srb->cmd->use_sg) */ 2175 /* srb->sg_index++; */ 2176 } 2177 } 2178 } 2179 if ((*pscsi_status & PHASEMASK) != PH_DATA_OUT) { 2180 cleanup_after_transfer(acb, srb); 2181 } 2182 } 2183 2184 2185 static void data_out_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2186 u16 *pscsi_status) 2187 { 2188 dprintkdbg(DBG_0, "data_out_phase1: (pid#%li) <%02i-%i>\n", 2189 srb->cmd->pid, srb->cmd->device->id, srb->cmd->device->lun); 2190 clear_fifo(acb, "data_out_phase1"); 2191 /* do prepare before transfer when data out phase */ 2192 data_io_transfer(acb, srb, XFERDATAOUT); 2193 } 2194 2195 static void data_in_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2196 u16 *pscsi_status) 2197 { 2198 u16 scsi_status = *pscsi_status; 2199 2200 dprintkdbg(DBG_0, "data_in_phase0: (pid#%li) <%02i-%i>\n", 2201 srb->cmd->pid, srb->cmd->device->id, srb->cmd->device->lun); 2202 2203 /* 2204 * KG: DataIn is much more tricky than DataOut. When the device is finished 2205 * and switches to another phase, the SCSI engine should be finished too. 2206 * But: There might still be bytes left in its FIFO to be fetched by the DMA 2207 * engine and transferred to memory. 2208 * We should wait for the FIFOs to be emptied by that (is there any way to 2209 * enforce this?) and then stop the DMA engine, because it might think, that 2210 * there are more bytes to follow. Yes, the device might disconnect prior to 2211 * having all bytes transferred! 2212 * Also we should make sure that all data from the DMA engine buffer's really 2213 * made its way to the system memory! Some documentation on this would not 2214 * seem to be a bad idea, actually. 2215 */ 2216 if (!(srb->state & SRB_XFERPAD)) { 2217 u32 d_left_counter; 2218 unsigned int sc, fc; 2219 2220 if (scsi_status & PARITYERROR) { 2221 dprintkl(KERN_INFO, "data_in_phase0: (pid#%li) " 2222 "Parity Error\n", srb->cmd->pid); 2223 srb->status |= PARITY_ERROR; 2224 } 2225 /* 2226 * KG: We should wait for the DMA FIFO to be empty ... 2227 * but: it would be better to wait first for the SCSI FIFO and then the 2228 * the DMA FIFO to become empty? How do we know, that the device not already 2229 * sent data to the FIFO in a MsgIn phase, eg.? 2230 */ 2231 if (!(DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT) & 0x80)) { 2232 #if 0 2233 int ctr = 6000000; 2234 dprintkl(KERN_DEBUG, 2235 "DIP0: Wait for DMA FIFO to flush ...\n"); 2236 /*DC395x_write8 (TRM_S1040_DMA_CONTROL, STOPDMAXFER); */ 2237 /*DC395x_write32 (TRM_S1040_SCSI_COUNTER, 7); */ 2238 /*DC395x_write8 (TRM_S1040_SCSI_COMMAND, SCMD_DMA_IN); */ 2239 while (! 2240 (DC395x_read16(acb, TRM_S1040_DMA_FIFOSTAT) & 2241 0x80) && --ctr); 2242 if (ctr < 6000000 - 1) 2243 dprintkl(KERN_DEBUG 2244 "DIP0: Had to wait for DMA ...\n"); 2245 if (!ctr) 2246 dprintkl(KERN_ERR, 2247 "Deadlock in DIP0 waiting for DMA FIFO empty!!\n"); 2248 /*DC395x_write32 (TRM_S1040_SCSI_COUNTER, 0); */ 2249 #endif 2250 dprintkdbg(DBG_KG, "data_in_phase0: " 2251 "DMA{fifocnt=0x%02x fifostat=0x%02x}\n", 2252 DC395x_read8(acb, TRM_S1040_DMA_FIFOCNT), 2253 DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT)); 2254 } 2255 /* Now: Check remainig data: The SCSI counters should tell us ... */ 2256 sc = DC395x_read32(acb, TRM_S1040_SCSI_COUNTER); 2257 fc = DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT); 2258 d_left_counter = sc + ((fc & 0x1f) 2259 << ((srb->dcb->sync_period & WIDE_SYNC) ? 1 : 2260 0)); 2261 dprintkdbg(DBG_KG, "data_in_phase0: " 2262 "SCSI{fifocnt=0x%02x%s ctr=0x%08x} " 2263 "DMA{fifocnt=0x%02x fifostat=0x%02x ctr=0x%08x} " 2264 "Remain{totxfer=%i scsi_fifo+ctr=%i}\n", 2265 fc, 2266 (srb->dcb->sync_period & WIDE_SYNC) ? "words" : "bytes", 2267 sc, 2268 fc, 2269 DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT), 2270 DC395x_read32(acb, TRM_S1040_DMA_CXCNT), 2271 srb->total_xfer_length, d_left_counter); 2272 #if DC395x_LASTPIO 2273 /* KG: Less than or equal to 4 bytes can not be transfered via DMA, it seems. */ 2274 if (d_left_counter 2275 && srb->total_xfer_length <= DC395x_LASTPIO) { 2276 size_t left_io = srb->total_xfer_length; 2277 2278 /*u32 addr = (srb->segment_x[srb->sg_index].address); */ 2279 /*sg_update_list (srb, d_left_counter); */ 2280 dprintkdbg(DBG_PIO, "data_in_phase0: PIO (%i %s) " 2281 "for remaining %i bytes:", 2282 fc & 0x1f, 2283 (srb->dcb->sync_period & WIDE_SYNC) ? 2284 "words" : "bytes", 2285 srb->total_xfer_length); 2286 if (srb->dcb->sync_period & WIDE_SYNC) 2287 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG2, 2288 CFG2_WIDEFIFO); 2289 while (left_io) { 2290 unsigned char *virt, *base = NULL; 2291 unsigned long flags = 0; 2292 size_t len = left_io; 2293 2294 if (srb->cmd->use_sg) { 2295 size_t offset = srb->request_length - left_io; 2296 local_irq_save(flags); 2297 /* Assumption: it's inside one page as it's at most 4 bytes and 2298 I just assume it's on a 4-byte boundary */ 2299 base = scsi_kmap_atomic_sg((struct scatterlist *)srb->cmd->request_buffer, 2300 srb->sg_count, &offset, &len); 2301 virt = base + offset; 2302 } else { 2303 virt = srb->cmd->request_buffer + srb->cmd->request_bufflen - left_io; 2304 len = left_io; 2305 } 2306 left_io -= len; 2307 2308 while (len) { 2309 u8 byte; 2310 byte = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); 2311 *virt++ = byte; 2312 2313 if (debug_enabled(DBG_PIO)) 2314 printk(" %02x", byte); 2315 2316 d_left_counter--; 2317 sg_subtract_one(srb); 2318 2319 len--; 2320 2321 fc = DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT); 2322 2323 if (fc == 0x40) { 2324 left_io = 0; 2325 break; 2326 } 2327 } 2328 2329 WARN_ON((fc != 0x40) == !d_left_counter); 2330 2331 if (fc == 0x40 && (srb->dcb->sync_period & WIDE_SYNC)) { 2332 /* Read the last byte ... */ 2333 if (srb->total_xfer_length > 0) { 2334 u8 byte = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); 2335 2336 *virt++ = byte; 2337 srb->total_xfer_length--; 2338 if (debug_enabled(DBG_PIO)) 2339 printk(" %02x", byte); 2340 } 2341 2342 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG2, 0); 2343 } 2344 2345 if (srb->cmd->use_sg) { 2346 scsi_kunmap_atomic_sg(base); 2347 local_irq_restore(flags); 2348 } 2349 } 2350 /*printk(" %08x", *(u32*)(bus_to_virt (addr))); */ 2351 /*srb->total_xfer_length = 0; */ 2352 if (debug_enabled(DBG_PIO)) 2353 printk("\n"); 2354 } 2355 #endif /* DC395x_LASTPIO */ 2356 2357 #if 0 2358 /* 2359 * KG: This was in DATAOUT. Does it also belong here? 2360 * Nobody seems to know what counter and fifo_cnt count exactly ... 2361 */ 2362 if (!(scsi_status & SCSIXFERDONE)) { 2363 /* 2364 * when data transfer from DMA FIFO to SCSI FIFO 2365 * if there was some data left in SCSI FIFO 2366 */ 2367 d_left_counter = 2368 (u32)(DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT) & 2369 0x1F); 2370 if (srb->dcb->sync_period & WIDE_SYNC) 2371 d_left_counter <<= 1; 2372 /* 2373 * if WIDE scsi SCSI FIFOCNT unit is word !!! 2374 * so need to *= 2 2375 * KG: Seems to be correct ... 2376 */ 2377 } 2378 #endif 2379 /* KG: This should not be needed any more! */ 2380 if (d_left_counter == 0 2381 || (scsi_status & SCSIXFERCNT_2_ZERO)) { 2382 #if 0 2383 int ctr = 6000000; 2384 u8 TempDMAstatus; 2385 do { 2386 TempDMAstatus = 2387 DC395x_read8(acb, TRM_S1040_DMA_STATUS); 2388 } while (!(TempDMAstatus & DMAXFERCOMP) && --ctr); 2389 if (!ctr) 2390 dprintkl(KERN_ERR, 2391 "Deadlock in DataInPhase0 waiting for DMA!!\n"); 2392 srb->total_xfer_length = 0; 2393 #endif 2394 srb->total_xfer_length = d_left_counter; 2395 } else { /* phase changed */ 2396 /* 2397 * parsing the case: 2398 * when a transfer not yet complete 2399 * but be disconnected by target 2400 * if transfer not yet complete 2401 * there were some data residue in SCSI FIFO or 2402 * SCSI transfer counter not empty 2403 */ 2404 sg_update_list(srb, d_left_counter); 2405 } 2406 } 2407 /* KG: The target may decide to disconnect: Empty FIFO before! */ 2408 if ((*pscsi_status & PHASEMASK) != PH_DATA_IN) { 2409 cleanup_after_transfer(acb, srb); 2410 } 2411 } 2412 2413 2414 static void data_in_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2415 u16 *pscsi_status) 2416 { 2417 dprintkdbg(DBG_0, "data_in_phase1: (pid#%li) <%02i-%i>\n", 2418 srb->cmd->pid, srb->cmd->device->id, srb->cmd->device->lun); 2419 data_io_transfer(acb, srb, XFERDATAIN); 2420 } 2421 2422 2423 static void data_io_transfer(struct AdapterCtlBlk *acb, 2424 struct ScsiReqBlk *srb, u16 io_dir) 2425 { 2426 struct DeviceCtlBlk *dcb = srb->dcb; 2427 u8 bval; 2428 dprintkdbg(DBG_0, 2429 "data_io_transfer: (pid#%li) <%02i-%i> %c len=%i, sg=(%i/%i)\n", 2430 srb->cmd->pid, srb->cmd->device->id, srb->cmd->device->lun, 2431 ((io_dir & DMACMD_DIR) ? 'r' : 'w'), 2432 srb->total_xfer_length, srb->sg_index, srb->sg_count); 2433 if (srb == acb->tmp_srb) 2434 dprintkl(KERN_ERR, "data_io_transfer: Using tmp_srb!\n"); 2435 if (srb->sg_index >= srb->sg_count) { 2436 /* can't happen? out of bounds error */ 2437 return; 2438 } 2439 2440 if (srb->total_xfer_length > DC395x_LASTPIO) { 2441 u8 dma_status = DC395x_read8(acb, TRM_S1040_DMA_STATUS); 2442 /* 2443 * KG: What should we do: Use SCSI Cmd 0x90/0x92? 2444 * Maybe, even ABORTXFER would be appropriate 2445 */ 2446 if (dma_status & XFERPENDING) { 2447 dprintkl(KERN_DEBUG, "data_io_transfer: Xfer pending! " 2448 "Expect trouble!\n"); 2449 dump_register_info(acb, dcb, srb); 2450 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, CLRXFIFO); 2451 } 2452 /* clear_fifo(acb, "IO"); */ 2453 /* 2454 * load what physical address of Scatter/Gather list table 2455 * want to be transfer 2456 */ 2457 srb->state |= SRB_DATA_XFER; 2458 DC395x_write32(acb, TRM_S1040_DMA_XHIGHADDR, 0); 2459 if (srb->cmd->use_sg) { /* with S/G */ 2460 io_dir |= DMACMD_SG; 2461 DC395x_write32(acb, TRM_S1040_DMA_XLOWADDR, 2462 srb->sg_bus_addr + 2463 sizeof(struct SGentry) * 2464 srb->sg_index); 2465 /* load how many bytes in the sg list table */ 2466 DC395x_write32(acb, TRM_S1040_DMA_XCNT, 2467 ((u32)(srb->sg_count - 2468 srb->sg_index) << 3)); 2469 } else { /* without S/G */ 2470 io_dir &= ~DMACMD_SG; 2471 DC395x_write32(acb, TRM_S1040_DMA_XLOWADDR, 2472 srb->segment_x[0].address); 2473 DC395x_write32(acb, TRM_S1040_DMA_XCNT, 2474 srb->segment_x[0].length); 2475 } 2476 /* load total transfer length (24bits) max value 16Mbyte */ 2477 DC395x_write32(acb, TRM_S1040_SCSI_COUNTER, 2478 srb->total_xfer_length); 2479 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 2480 if (io_dir & DMACMD_DIR) { /* read */ 2481 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, 2482 SCMD_DMA_IN); 2483 DC395x_write16(acb, TRM_S1040_DMA_COMMAND, io_dir); 2484 } else { 2485 DC395x_write16(acb, TRM_S1040_DMA_COMMAND, io_dir); 2486 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, 2487 SCMD_DMA_OUT); 2488 } 2489 2490 } 2491 #if DC395x_LASTPIO 2492 else if (srb->total_xfer_length > 0) { /* The last four bytes: Do PIO */ 2493 /* 2494 * load what physical address of Scatter/Gather list table 2495 * want to be transfer 2496 */ 2497 srb->state |= SRB_DATA_XFER; 2498 /* load total transfer length (24bits) max value 16Mbyte */ 2499 DC395x_write32(acb, TRM_S1040_SCSI_COUNTER, 2500 srb->total_xfer_length); 2501 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 2502 if (io_dir & DMACMD_DIR) { /* read */ 2503 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, 2504 SCMD_FIFO_IN); 2505 } else { /* write */ 2506 int ln = srb->total_xfer_length; 2507 size_t left_io = srb->total_xfer_length; 2508 2509 if (srb->dcb->sync_period & WIDE_SYNC) 2510 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG2, 2511 CFG2_WIDEFIFO); 2512 2513 while (left_io) { 2514 unsigned char *virt, *base = NULL; 2515 unsigned long flags = 0; 2516 size_t len = left_io; 2517 2518 if (srb->cmd->use_sg) { 2519 size_t offset = srb->request_length - left_io; 2520 local_irq_save(flags); 2521 /* Again, max 4 bytes */ 2522 base = scsi_kmap_atomic_sg((struct scatterlist *)srb->cmd->request_buffer, 2523 srb->sg_count, &offset, &len); 2524 virt = base + offset; 2525 } else { 2526 virt = srb->cmd->request_buffer + srb->cmd->request_bufflen - left_io; 2527 len = left_io; 2528 } 2529 left_io -= len; 2530 2531 while (len--) { 2532 if (debug_enabled(DBG_PIO)) 2533 printk(" %02x", *virt); 2534 2535 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, *virt++); 2536 2537 sg_subtract_one(srb); 2538 } 2539 2540 if (srb->cmd->use_sg) { 2541 scsi_kunmap_atomic_sg(base); 2542 local_irq_restore(flags); 2543 } 2544 } 2545 if (srb->dcb->sync_period & WIDE_SYNC) { 2546 if (ln % 2) { 2547 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 0); 2548 if (debug_enabled(DBG_PIO)) 2549 printk(" |00"); 2550 } 2551 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG2, 0); 2552 } 2553 /*DC395x_write32(acb, TRM_S1040_SCSI_COUNTER, ln); */ 2554 if (debug_enabled(DBG_PIO)) 2555 printk("\n"); 2556 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, 2557 SCMD_FIFO_OUT); 2558 } 2559 } 2560 #endif /* DC395x_LASTPIO */ 2561 else { /* xfer pad */ 2562 u8 data = 0, data2 = 0; 2563 if (srb->sg_count) { 2564 srb->adapter_status = H_OVER_UNDER_RUN; 2565 srb->status |= OVER_RUN; 2566 } 2567 /* 2568 * KG: despite the fact that we are using 16 bits I/O ops 2569 * the SCSI FIFO is only 8 bits according to the docs 2570 * (we can set bit 1 in 0x8f to serialize FIFO access ...) 2571 */ 2572 if (dcb->sync_period & WIDE_SYNC) { 2573 DC395x_write32(acb, TRM_S1040_SCSI_COUNTER, 2); 2574 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG2, 2575 CFG2_WIDEFIFO); 2576 if (io_dir & DMACMD_DIR) { 2577 data = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); 2578 data2 = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); 2579 } else { 2580 /* Danger, Robinson: If you find KGs 2581 * scattered over the wide disk, the driver 2582 * or chip is to blame :-( */ 2583 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 'K'); 2584 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 'G'); 2585 } 2586 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG2, 0); 2587 } else { 2588 DC395x_write32(acb, TRM_S1040_SCSI_COUNTER, 1); 2589 /* Danger, Robinson: If you find a collection of Ks on your disk 2590 * something broke :-( */ 2591 if (io_dir & DMACMD_DIR) 2592 data = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); 2593 else 2594 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 'K'); 2595 } 2596 srb->state |= SRB_XFERPAD; 2597 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 2598 /* SCSI command */ 2599 bval = (io_dir & DMACMD_DIR) ? SCMD_FIFO_IN : SCMD_FIFO_OUT; 2600 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, bval); 2601 } 2602 } 2603 2604 2605 static void status_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2606 u16 *pscsi_status) 2607 { 2608 dprintkdbg(DBG_0, "status_phase0: (pid#%li) <%02i-%i>\n", 2609 srb->cmd->pid, srb->cmd->device->id, srb->cmd->device->lun); 2610 srb->target_status = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); 2611 srb->end_message = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); /* get message */ 2612 srb->state = SRB_COMPLETED; 2613 *pscsi_status = PH_BUS_FREE; /*.. initial phase */ 2614 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 2615 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_MSGACCEPT); 2616 } 2617 2618 2619 static void status_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2620 u16 *pscsi_status) 2621 { 2622 dprintkdbg(DBG_0, "status_phase1: (pid#%li) <%02i-%i>\n", 2623 srb->cmd->pid, srb->cmd->device->id, srb->cmd->device->lun); 2624 srb->state = SRB_STATUS; 2625 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 2626 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_COMP); 2627 } 2628 2629 2630 /* Check if the message is complete */ 2631 static inline u8 msgin_completed(u8 * msgbuf, u32 len) 2632 { 2633 if (*msgbuf == EXTENDED_MESSAGE) { 2634 if (len < 2) 2635 return 0; 2636 if (len < msgbuf[1] + 2) 2637 return 0; 2638 } else if (*msgbuf >= 0x20 && *msgbuf <= 0x2f) /* two byte messages */ 2639 if (len < 2) 2640 return 0; 2641 return 1; 2642 } 2643 2644 /* reject_msg */ 2645 static inline void msgin_reject(struct AdapterCtlBlk *acb, 2646 struct ScsiReqBlk *srb) 2647 { 2648 srb->msgout_buf[0] = MESSAGE_REJECT; 2649 srb->msg_count = 1; 2650 DC395x_ENABLE_MSGOUT; 2651 srb->state &= ~SRB_MSGIN; 2652 srb->state |= SRB_MSGOUT; 2653 dprintkl(KERN_INFO, "msgin_reject: 0x%02x <%02i-%i>\n", 2654 srb->msgin_buf[0], 2655 srb->dcb->target_id, srb->dcb->target_lun); 2656 } 2657 2658 2659 static struct ScsiReqBlk *msgin_qtag(struct AdapterCtlBlk *acb, 2660 struct DeviceCtlBlk *dcb, u8 tag) 2661 { 2662 struct ScsiReqBlk *srb = NULL; 2663 struct ScsiReqBlk *i; 2664 dprintkdbg(DBG_0, "msgin_qtag: (pid#%li) tag=%i srb=%p\n", 2665 srb->cmd->pid, tag, srb); 2666 2667 if (!(dcb->tag_mask & (1 << tag))) 2668 dprintkl(KERN_DEBUG, 2669 "msgin_qtag: tag_mask=0x%08x does not reserve tag %i!\n", 2670 dcb->tag_mask, tag); 2671 2672 if (list_empty(&dcb->srb_going_list)) 2673 goto mingx0; 2674 list_for_each_entry(i, &dcb->srb_going_list, list) { 2675 if (i->tag_number == tag) { 2676 srb = i; 2677 break; 2678 } 2679 } 2680 if (!srb) 2681 goto mingx0; 2682 2683 dprintkdbg(DBG_0, "msgin_qtag: (pid#%li) <%02i-%i>\n", 2684 srb->cmd->pid, srb->dcb->target_id, srb->dcb->target_lun); 2685 if (dcb->flag & ABORT_DEV_) { 2686 /*srb->state = SRB_ABORT_SENT; */ 2687 enable_msgout_abort(acb, srb); 2688 } 2689 2690 if (!(srb->state & SRB_DISCONNECT)) 2691 goto mingx0; 2692 2693 memcpy(srb->msgin_buf, dcb->active_srb->msgin_buf, acb->msg_len); 2694 srb->state |= dcb->active_srb->state; 2695 srb->state |= SRB_DATA_XFER; 2696 dcb->active_srb = srb; 2697 /* How can we make the DORS happy? */ 2698 return srb; 2699 2700 mingx0: 2701 srb = acb->tmp_srb; 2702 srb->state = SRB_UNEXPECT_RESEL; 2703 dcb->active_srb = srb; 2704 srb->msgout_buf[0] = MSG_ABORT_TAG; 2705 srb->msg_count = 1; 2706 DC395x_ENABLE_MSGOUT; 2707 dprintkl(KERN_DEBUG, "msgin_qtag: Unknown tag %i - abort\n", tag); 2708 return srb; 2709 } 2710 2711 2712 static inline void reprogram_regs(struct AdapterCtlBlk *acb, 2713 struct DeviceCtlBlk *dcb) 2714 { 2715 DC395x_write8(acb, TRM_S1040_SCSI_TARGETID, dcb->target_id); 2716 DC395x_write8(acb, TRM_S1040_SCSI_SYNC, dcb->sync_period); 2717 DC395x_write8(acb, TRM_S1040_SCSI_OFFSET, dcb->sync_offset); 2718 set_xfer_rate(acb, dcb); 2719 } 2720 2721 2722 /* set async transfer mode */ 2723 static void msgin_set_async(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb) 2724 { 2725 struct DeviceCtlBlk *dcb = srb->dcb; 2726 dprintkl(KERN_DEBUG, "msgin_set_async: No sync transfers <%02i-%i>\n", 2727 dcb->target_id, dcb->target_lun); 2728 2729 dcb->sync_mode &= ~(SYNC_NEGO_ENABLE); 2730 dcb->sync_mode |= SYNC_NEGO_DONE; 2731 /*dcb->sync_period &= 0; */ 2732 dcb->sync_offset = 0; 2733 dcb->min_nego_period = 200 >> 2; /* 200ns <=> 5 MHz */ 2734 srb->state &= ~SRB_DO_SYNC_NEGO; 2735 reprogram_regs(acb, dcb); 2736 if ((dcb->sync_mode & WIDE_NEGO_ENABLE) 2737 && !(dcb->sync_mode & WIDE_NEGO_DONE)) { 2738 build_wdtr(acb, dcb, srb); 2739 DC395x_ENABLE_MSGOUT; 2740 dprintkdbg(DBG_0, "msgin_set_async(rej): Try WDTR anyway\n"); 2741 } 2742 } 2743 2744 2745 /* set sync transfer mode */ 2746 static void msgin_set_sync(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb) 2747 { 2748 struct DeviceCtlBlk *dcb = srb->dcb; 2749 u8 bval; 2750 int fact; 2751 dprintkdbg(DBG_1, "msgin_set_sync: <%02i> Sync: %ins " 2752 "(%02i.%01i MHz) Offset %i\n", 2753 dcb->target_id, srb->msgin_buf[3] << 2, 2754 (250 / srb->msgin_buf[3]), 2755 ((250 % srb->msgin_buf[3]) * 10) / srb->msgin_buf[3], 2756 srb->msgin_buf[4]); 2757 2758 if (srb->msgin_buf[4] > 15) 2759 srb->msgin_buf[4] = 15; 2760 if (!(dcb->dev_mode & NTC_DO_SYNC_NEGO)) 2761 dcb->sync_offset = 0; 2762 else if (dcb->sync_offset == 0) 2763 dcb->sync_offset = srb->msgin_buf[4]; 2764 if (srb->msgin_buf[4] > dcb->sync_offset) 2765 srb->msgin_buf[4] = dcb->sync_offset; 2766 else 2767 dcb->sync_offset = srb->msgin_buf[4]; 2768 bval = 0; 2769 while (bval < 7 && (srb->msgin_buf[3] > clock_period[bval] 2770 || dcb->min_nego_period > 2771 clock_period[bval])) 2772 bval++; 2773 if (srb->msgin_buf[3] < clock_period[bval]) 2774 dprintkl(KERN_INFO, 2775 "msgin_set_sync: Increase sync nego period to %ins\n", 2776 clock_period[bval] << 2); 2777 srb->msgin_buf[3] = clock_period[bval]; 2778 dcb->sync_period &= 0xf0; 2779 dcb->sync_period |= ALT_SYNC | bval; 2780 dcb->min_nego_period = srb->msgin_buf[3]; 2781 2782 if (dcb->sync_period & WIDE_SYNC) 2783 fact = 500; 2784 else 2785 fact = 250; 2786 2787 dprintkl(KERN_INFO, 2788 "Target %02i: %s Sync: %ins Offset %i (%02i.%01i MB/s)\n", 2789 dcb->target_id, (fact == 500) ? "Wide16" : "", 2790 dcb->min_nego_period << 2, dcb->sync_offset, 2791 (fact / dcb->min_nego_period), 2792 ((fact % dcb->min_nego_period) * 10 + 2793 dcb->min_nego_period / 2) / dcb->min_nego_period); 2794 2795 if (!(srb->state & SRB_DO_SYNC_NEGO)) { 2796 /* Reply with corrected SDTR Message */ 2797 dprintkl(KERN_DEBUG, "msgin_set_sync: answer w/%ins %i\n", 2798 srb->msgin_buf[3] << 2, srb->msgin_buf[4]); 2799 2800 memcpy(srb->msgout_buf, srb->msgin_buf, 5); 2801 srb->msg_count = 5; 2802 DC395x_ENABLE_MSGOUT; 2803 dcb->sync_mode |= SYNC_NEGO_DONE; 2804 } else { 2805 if ((dcb->sync_mode & WIDE_NEGO_ENABLE) 2806 && !(dcb->sync_mode & WIDE_NEGO_DONE)) { 2807 build_wdtr(acb, dcb, srb); 2808 DC395x_ENABLE_MSGOUT; 2809 dprintkdbg(DBG_0, "msgin_set_sync: Also try WDTR\n"); 2810 } 2811 } 2812 srb->state &= ~SRB_DO_SYNC_NEGO; 2813 dcb->sync_mode |= SYNC_NEGO_DONE | SYNC_NEGO_ENABLE; 2814 2815 reprogram_regs(acb, dcb); 2816 } 2817 2818 2819 static inline void msgin_set_nowide(struct AdapterCtlBlk *acb, 2820 struct ScsiReqBlk *srb) 2821 { 2822 struct DeviceCtlBlk *dcb = srb->dcb; 2823 dprintkdbg(DBG_1, "msgin_set_nowide: <%02i>\n", dcb->target_id); 2824 2825 dcb->sync_period &= ~WIDE_SYNC; 2826 dcb->sync_mode &= ~(WIDE_NEGO_ENABLE); 2827 dcb->sync_mode |= WIDE_NEGO_DONE; 2828 srb->state &= ~SRB_DO_WIDE_NEGO; 2829 reprogram_regs(acb, dcb); 2830 if ((dcb->sync_mode & SYNC_NEGO_ENABLE) 2831 && !(dcb->sync_mode & SYNC_NEGO_DONE)) { 2832 build_sdtr(acb, dcb, srb); 2833 DC395x_ENABLE_MSGOUT; 2834 dprintkdbg(DBG_0, "msgin_set_nowide: Rejected. Try SDTR anyway\n"); 2835 } 2836 } 2837 2838 static void msgin_set_wide(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb) 2839 { 2840 struct DeviceCtlBlk *dcb = srb->dcb; 2841 u8 wide = (dcb->dev_mode & NTC_DO_WIDE_NEGO 2842 && acb->config & HCC_WIDE_CARD) ? 1 : 0; 2843 dprintkdbg(DBG_1, "msgin_set_wide: <%02i>\n", dcb->target_id); 2844 2845 if (srb->msgin_buf[3] > wide) 2846 srb->msgin_buf[3] = wide; 2847 /* Completed */ 2848 if (!(srb->state & SRB_DO_WIDE_NEGO)) { 2849 dprintkl(KERN_DEBUG, 2850 "msgin_set_wide: Wide nego initiated <%02i>\n", 2851 dcb->target_id); 2852 memcpy(srb->msgout_buf, srb->msgin_buf, 4); 2853 srb->msg_count = 4; 2854 srb->state |= SRB_DO_WIDE_NEGO; 2855 DC395x_ENABLE_MSGOUT; 2856 } 2857 2858 dcb->sync_mode |= (WIDE_NEGO_ENABLE | WIDE_NEGO_DONE); 2859 if (srb->msgin_buf[3] > 0) 2860 dcb->sync_period |= WIDE_SYNC; 2861 else 2862 dcb->sync_period &= ~WIDE_SYNC; 2863 srb->state &= ~SRB_DO_WIDE_NEGO; 2864 /*dcb->sync_mode &= ~(WIDE_NEGO_ENABLE+WIDE_NEGO_DONE); */ 2865 dprintkdbg(DBG_1, 2866 "msgin_set_wide: Wide (%i bit) negotiated <%02i>\n", 2867 (8 << srb->msgin_buf[3]), dcb->target_id); 2868 reprogram_regs(acb, dcb); 2869 if ((dcb->sync_mode & SYNC_NEGO_ENABLE) 2870 && !(dcb->sync_mode & SYNC_NEGO_DONE)) { 2871 build_sdtr(acb, dcb, srb); 2872 DC395x_ENABLE_MSGOUT; 2873 dprintkdbg(DBG_0, "msgin_set_wide: Also try SDTR.\n"); 2874 } 2875 } 2876 2877 2878 /* 2879 * extended message codes: 2880 * 2881 * code description 2882 * 2883 * 02h Reserved 2884 * 00h MODIFY DATA POINTER 2885 * 01h SYNCHRONOUS DATA TRANSFER REQUEST 2886 * 03h WIDE DATA TRANSFER REQUEST 2887 * 04h - 7Fh Reserved 2888 * 80h - FFh Vendor specific 2889 */ 2890 static void msgin_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2891 u16 *pscsi_status) 2892 { 2893 struct DeviceCtlBlk *dcb = acb->active_dcb; 2894 dprintkdbg(DBG_0, "msgin_phase0: (pid#%li)\n", srb->cmd->pid); 2895 2896 srb->msgin_buf[acb->msg_len++] = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); 2897 if (msgin_completed(srb->msgin_buf, acb->msg_len)) { 2898 /* Now eval the msg */ 2899 switch (srb->msgin_buf[0]) { 2900 case DISCONNECT: 2901 srb->state = SRB_DISCONNECT; 2902 break; 2903 2904 case SIMPLE_QUEUE_TAG: 2905 case HEAD_OF_QUEUE_TAG: 2906 case ORDERED_QUEUE_TAG: 2907 srb = 2908 msgin_qtag(acb, dcb, 2909 srb->msgin_buf[1]); 2910 break; 2911 2912 case MESSAGE_REJECT: 2913 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, 2914 DO_CLRATN | DO_DATALATCH); 2915 /* A sync nego message was rejected ! */ 2916 if (srb->state & SRB_DO_SYNC_NEGO) { 2917 msgin_set_async(acb, srb); 2918 break; 2919 } 2920 /* A wide nego message was rejected ! */ 2921 if (srb->state & SRB_DO_WIDE_NEGO) { 2922 msgin_set_nowide(acb, srb); 2923 break; 2924 } 2925 enable_msgout_abort(acb, srb); 2926 /*srb->state |= SRB_ABORT_SENT */ 2927 break; 2928 2929 case EXTENDED_MESSAGE: 2930 /* SDTR */ 2931 if (srb->msgin_buf[1] == 3 2932 && srb->msgin_buf[2] == EXTENDED_SDTR) { 2933 msgin_set_sync(acb, srb); 2934 break; 2935 } 2936 /* WDTR */ 2937 if (srb->msgin_buf[1] == 2 2938 && srb->msgin_buf[2] == EXTENDED_WDTR 2939 && srb->msgin_buf[3] <= 2) { /* sanity check ... */ 2940 msgin_set_wide(acb, srb); 2941 break; 2942 } 2943 msgin_reject(acb, srb); 2944 break; 2945 2946 case MSG_IGNOREWIDE: 2947 /* Discard wide residual */ 2948 dprintkdbg(DBG_0, "msgin_phase0: Ignore Wide Residual!\n"); 2949 break; 2950 2951 case COMMAND_COMPLETE: 2952 /* nothing has to be done */ 2953 break; 2954 2955 case SAVE_POINTERS: 2956 /* 2957 * SAVE POINTER may be ignored as we have the struct 2958 * ScsiReqBlk* associated with the scsi command. 2959 */ 2960 dprintkdbg(DBG_0, "msgin_phase0: (pid#%li) " 2961 "SAVE POINTER rem=%i Ignore\n", 2962 srb->cmd->pid, srb->total_xfer_length); 2963 break; 2964 2965 case RESTORE_POINTERS: 2966 dprintkdbg(DBG_0, "msgin_phase0: RESTORE POINTER. Ignore\n"); 2967 break; 2968 2969 case ABORT: 2970 dprintkdbg(DBG_0, "msgin_phase0: (pid#%li) " 2971 "<%02i-%i> ABORT msg\n", 2972 srb->cmd->pid, dcb->target_id, 2973 dcb->target_lun); 2974 dcb->flag |= ABORT_DEV_; 2975 enable_msgout_abort(acb, srb); 2976 break; 2977 2978 default: 2979 /* reject unknown messages */ 2980 if (srb->msgin_buf[0] & IDENTIFY_BASE) { 2981 dprintkdbg(DBG_0, "msgin_phase0: Identify msg\n"); 2982 srb->msg_count = 1; 2983 srb->msgout_buf[0] = dcb->identify_msg; 2984 DC395x_ENABLE_MSGOUT; 2985 srb->state |= SRB_MSGOUT; 2986 /*break; */ 2987 } 2988 msgin_reject(acb, srb); 2989 } 2990 2991 /* Clear counter and MsgIn state */ 2992 srb->state &= ~SRB_MSGIN; 2993 acb->msg_len = 0; 2994 } 2995 *pscsi_status = PH_BUS_FREE; 2996 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important ... you know! */ 2997 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_MSGACCEPT); 2998 } 2999 3000 3001 static void msgin_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 3002 u16 *pscsi_status) 3003 { 3004 dprintkdbg(DBG_0, "msgin_phase1: (pid#%li)\n", srb->cmd->pid); 3005 clear_fifo(acb, "msgin_phase1"); 3006 DC395x_write32(acb, TRM_S1040_SCSI_COUNTER, 1); 3007 if (!(srb->state & SRB_MSGIN)) { 3008 srb->state &= ~SRB_DISCONNECT; 3009 srb->state |= SRB_MSGIN; 3010 } 3011 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 3012 /* SCSI command */ 3013 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_FIFO_IN); 3014 } 3015 3016 3017 static void nop0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 3018 u16 *pscsi_status) 3019 { 3020 } 3021 3022 3023 static void nop1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 3024 u16 *pscsi_status) 3025 { 3026 } 3027 3028 3029 static void set_xfer_rate(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb) 3030 { 3031 struct DeviceCtlBlk *i; 3032 3033 /* set all lun device's period, offset */ 3034 if (dcb->identify_msg & 0x07) 3035 return; 3036 3037 if (acb->scan_devices) { 3038 current_sync_offset = dcb->sync_offset; 3039 return; 3040 } 3041 3042 list_for_each_entry(i, &acb->dcb_list, list) 3043 if (i->target_id == dcb->target_id) { 3044 i->sync_period = dcb->sync_period; 3045 i->sync_offset = dcb->sync_offset; 3046 i->sync_mode = dcb->sync_mode; 3047 i->min_nego_period = dcb->min_nego_period; 3048 } 3049 } 3050 3051 3052 static void disconnect(struct AdapterCtlBlk *acb) 3053 { 3054 struct DeviceCtlBlk *dcb = acb->active_dcb; 3055 struct ScsiReqBlk *srb; 3056 3057 if (!dcb) { 3058 dprintkl(KERN_ERR, "disconnect: No such device\n"); 3059 udelay(500); 3060 /* Suspend queue for a while */ 3061 acb->scsi_host->last_reset = 3062 jiffies + HZ / 2 + 3063 HZ * acb->eeprom.delay_time; 3064 clear_fifo(acb, "disconnectEx"); 3065 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_HWRESELECT); 3066 return; 3067 } 3068 srb = dcb->active_srb; 3069 acb->active_dcb = NULL; 3070 dprintkdbg(DBG_0, "disconnect: (pid#%li)\n", srb->cmd->pid); 3071 3072 srb->scsi_phase = PH_BUS_FREE; /* initial phase */ 3073 clear_fifo(acb, "disconnect"); 3074 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_HWRESELECT); 3075 if (srb->state & SRB_UNEXPECT_RESEL) { 3076 dprintkl(KERN_ERR, 3077 "disconnect: Unexpected reselection <%02i-%i>\n", 3078 dcb->target_id, dcb->target_lun); 3079 srb->state = 0; 3080 waiting_process_next(acb); 3081 } else if (srb->state & SRB_ABORT_SENT) { 3082 dcb->flag &= ~ABORT_DEV_; 3083 acb->scsi_host->last_reset = jiffies + HZ / 2 + 1; 3084 dprintkl(KERN_ERR, "disconnect: SRB_ABORT_SENT\n"); 3085 doing_srb_done(acb, DID_ABORT, srb->cmd, 1); 3086 waiting_process_next(acb); 3087 } else { 3088 if ((srb->state & (SRB_START_ + SRB_MSGOUT)) 3089 || !(srb-> 3090 state & (SRB_DISCONNECT + SRB_COMPLETED))) { 3091 /* 3092 * Selection time out 3093 * SRB_START_ || SRB_MSGOUT || (!SRB_DISCONNECT && !SRB_COMPLETED) 3094 */ 3095 /* Unexp. Disc / Sel Timeout */ 3096 if (srb->state != SRB_START_ 3097 && srb->state != SRB_MSGOUT) { 3098 srb->state = SRB_READY; 3099 dprintkl(KERN_DEBUG, 3100 "disconnect: (pid#%li) Unexpected\n", 3101 srb->cmd->pid); 3102 srb->target_status = SCSI_STAT_SEL_TIMEOUT; 3103 goto disc1; 3104 } else { 3105 /* Normal selection timeout */ 3106 dprintkdbg(DBG_KG, "disconnect: (pid#%li) " 3107 "<%02i-%i> SelTO\n", srb->cmd->pid, 3108 dcb->target_id, dcb->target_lun); 3109 if (srb->retry_count++ > DC395x_MAX_RETRIES 3110 || acb->scan_devices) { 3111 srb->target_status = 3112 SCSI_STAT_SEL_TIMEOUT; 3113 goto disc1; 3114 } 3115 free_tag(dcb, srb); 3116 srb_going_to_waiting_move(dcb, srb); 3117 dprintkdbg(DBG_KG, 3118 "disconnect: (pid#%li) Retry\n", 3119 srb->cmd->pid); 3120 waiting_set_timer(acb, HZ / 20); 3121 } 3122 } else if (srb->state & SRB_DISCONNECT) { 3123 u8 bval = DC395x_read8(acb, TRM_S1040_SCSI_SIGNAL); 3124 /* 3125 * SRB_DISCONNECT (This is what we expect!) 3126 */ 3127 if (bval & 0x40) { 3128 dprintkdbg(DBG_0, "disconnect: SCSI bus stat " 3129 " 0x%02x: ACK set! Other controllers?\n", 3130 bval); 3131 /* It could come from another initiator, therefore don't do much ! */ 3132 } else 3133 waiting_process_next(acb); 3134 } else if (srb->state & SRB_COMPLETED) { 3135 disc1: 3136 /* 3137 ** SRB_COMPLETED 3138 */ 3139 free_tag(dcb, srb); 3140 dcb->active_srb = NULL; 3141 srb->state = SRB_FREE; 3142 srb_done(acb, dcb, srb); 3143 } 3144 } 3145 } 3146 3147 3148 static void reselect(struct AdapterCtlBlk *acb) 3149 { 3150 struct DeviceCtlBlk *dcb = acb->active_dcb; 3151 struct ScsiReqBlk *srb = NULL; 3152 u16 rsel_tar_lun_id; 3153 u8 id, lun; 3154 u8 arblostflag = 0; 3155 dprintkdbg(DBG_0, "reselect: acb=%p\n", acb); 3156 3157 clear_fifo(acb, "reselect"); 3158 /*DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_HWRESELECT | DO_DATALATCH); */ 3159 /* Read Reselected Target ID and LUN */ 3160 rsel_tar_lun_id = DC395x_read16(acb, TRM_S1040_SCSI_TARGETID); 3161 if (dcb) { /* Arbitration lost but Reselection win */ 3162 srb = dcb->active_srb; 3163 if (!srb) { 3164 dprintkl(KERN_DEBUG, "reselect: Arb lost Resel won, " 3165 "but active_srb == NULL\n"); 3166 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 3167 return; 3168 } 3169 /* Why the if ? */ 3170 if (!acb->scan_devices) { 3171 dprintkdbg(DBG_KG, "reselect: (pid#%li) <%02i-%i> " 3172 "Arb lost but Resel win rsel=%i stat=0x%04x\n", 3173 srb->cmd->pid, dcb->target_id, 3174 dcb->target_lun, rsel_tar_lun_id, 3175 DC395x_read16(acb, TRM_S1040_SCSI_STATUS)); 3176 arblostflag = 1; 3177 /*srb->state |= SRB_DISCONNECT; */ 3178 3179 srb->state = SRB_READY; 3180 free_tag(dcb, srb); 3181 srb_going_to_waiting_move(dcb, srb); 3182 waiting_set_timer(acb, HZ / 20); 3183 3184 /* return; */ 3185 } 3186 } 3187 /* Read Reselected Target Id and LUN */ 3188 if (!(rsel_tar_lun_id & (IDENTIFY_BASE << 8))) 3189 dprintkl(KERN_DEBUG, "reselect: Expects identify msg. " 3190 "Got %i!\n", rsel_tar_lun_id); 3191 id = rsel_tar_lun_id & 0xff; 3192 lun = (rsel_tar_lun_id >> 8) & 7; 3193 dcb = find_dcb(acb, id, lun); 3194 if (!dcb) { 3195 dprintkl(KERN_ERR, "reselect: From non existent device " 3196 "<%02i-%i>\n", id, lun); 3197 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 3198 return; 3199 } 3200 acb->active_dcb = dcb; 3201 3202 if (!(dcb->dev_mode & NTC_DO_DISCONNECT)) 3203 dprintkl(KERN_DEBUG, "reselect: in spite of forbidden " 3204 "disconnection? <%02i-%i>\n", 3205 dcb->target_id, dcb->target_lun); 3206 3207 if (dcb->sync_mode & EN_TAG_QUEUEING /*&& !arblostflag */) { 3208 srb = acb->tmp_srb; 3209 dcb->active_srb = srb; 3210 } else { 3211 /* There can be only one! */ 3212 srb = dcb->active_srb; 3213 if (!srb || !(srb->state & SRB_DISCONNECT)) { 3214 /* 3215 * abort command 3216 */ 3217 dprintkl(KERN_DEBUG, 3218 "reselect: w/o disconnected cmds <%02i-%i>\n", 3219 dcb->target_id, dcb->target_lun); 3220 srb = acb->tmp_srb; 3221 srb->state = SRB_UNEXPECT_RESEL; 3222 dcb->active_srb = srb; 3223 enable_msgout_abort(acb, srb); 3224 } else { 3225 if (dcb->flag & ABORT_DEV_) { 3226 /*srb->state = SRB_ABORT_SENT; */ 3227 enable_msgout_abort(acb, srb); 3228 } else 3229 srb->state = SRB_DATA_XFER; 3230 3231 } 3232 } 3233 srb->scsi_phase = PH_BUS_FREE; /* initial phase */ 3234 3235 /* Program HA ID, target ID, period and offset */ 3236 dprintkdbg(DBG_0, "reselect: select <%i>\n", dcb->target_id); 3237 DC395x_write8(acb, TRM_S1040_SCSI_HOSTID, acb->scsi_host->this_id); /* host ID */ 3238 DC395x_write8(acb, TRM_S1040_SCSI_TARGETID, dcb->target_id); /* target ID */ 3239 DC395x_write8(acb, TRM_S1040_SCSI_OFFSET, dcb->sync_offset); /* offset */ 3240 DC395x_write8(acb, TRM_S1040_SCSI_SYNC, dcb->sync_period); /* sync period, wide */ 3241 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 3242 /* SCSI command */ 3243 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_MSGACCEPT); 3244 } 3245 3246 3247 static inline u8 tagq_blacklist(char *name) 3248 { 3249 #ifndef DC395x_NO_TAGQ 3250 #if 0 3251 u8 i; 3252 for (i = 0; i < BADDEVCNT; i++) 3253 if (memcmp(name, DC395x_baddevname1[i], 28) == 0) 3254 return 1; 3255 #endif 3256 return 0; 3257 #else 3258 return 1; 3259 #endif 3260 } 3261 3262 3263 static void disc_tagq_set(struct DeviceCtlBlk *dcb, struct ScsiInqData *ptr) 3264 { 3265 /* Check for SCSI format (ANSI and Response data format) */ 3266 if ((ptr->Vers & 0x07) >= 2 || (ptr->RDF & 0x0F) == 2) { 3267 if ((ptr->Flags & SCSI_INQ_CMDQUEUE) 3268 && (dcb->dev_mode & NTC_DO_TAG_QUEUEING) && 3269 /*(dcb->dev_mode & NTC_DO_DISCONNECT) */ 3270 /* ((dcb->dev_type == TYPE_DISK) 3271 || (dcb->dev_type == TYPE_MOD)) && */ 3272 !tagq_blacklist(((char *)ptr) + 8)) { 3273 if (dcb->max_command == 1) 3274 dcb->max_command = 3275 dcb->acb->tag_max_num; 3276 dcb->sync_mode |= EN_TAG_QUEUEING; 3277 /*dcb->tag_mask = 0; */ 3278 } else 3279 dcb->max_command = 1; 3280 } 3281 } 3282 3283 3284 static void add_dev(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 3285 struct ScsiInqData *ptr) 3286 { 3287 u8 bval1 = ptr->DevType & SCSI_DEVTYPE; 3288 dcb->dev_type = bval1; 3289 /* if (bval1 == TYPE_DISK || bval1 == TYPE_MOD) */ 3290 disc_tagq_set(dcb, ptr); 3291 } 3292 3293 3294 /* unmap mapped pci regions from SRB */ 3295 static void pci_unmap_srb(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb) 3296 { 3297 struct scsi_cmnd *cmd = srb->cmd; 3298 enum dma_data_direction dir = cmd->sc_data_direction; 3299 if (cmd->use_sg && dir != PCI_DMA_NONE) { 3300 /* unmap DC395x SG list */ 3301 dprintkdbg(DBG_SG, "pci_unmap_srb: list=%08x(%05x)\n", 3302 srb->sg_bus_addr, SEGMENTX_LEN); 3303 pci_unmap_single(acb->dev, srb->sg_bus_addr, 3304 SEGMENTX_LEN, 3305 PCI_DMA_TODEVICE); 3306 dprintkdbg(DBG_SG, "pci_unmap_srb: segs=%i buffer=%p\n", 3307 cmd->use_sg, cmd->request_buffer); 3308 /* unmap the sg segments */ 3309 pci_unmap_sg(acb->dev, 3310 (struct scatterlist *)cmd->request_buffer, 3311 cmd->use_sg, dir); 3312 } else if (cmd->request_buffer && dir != PCI_DMA_NONE) { 3313 dprintkdbg(DBG_SG, "pci_unmap_srb: buffer=%08x(%05x)\n", 3314 srb->segment_x[0].address, cmd->request_bufflen); 3315 pci_unmap_single(acb->dev, srb->segment_x[0].address, 3316 cmd->request_bufflen, dir); 3317 } 3318 } 3319 3320 3321 /* unmap mapped pci sense buffer from SRB */ 3322 static void pci_unmap_srb_sense(struct AdapterCtlBlk *acb, 3323 struct ScsiReqBlk *srb) 3324 { 3325 if (!(srb->flag & AUTO_REQSENSE)) 3326 return; 3327 /* Unmap sense buffer */ 3328 dprintkdbg(DBG_SG, "pci_unmap_srb_sense: buffer=%08x\n", 3329 srb->segment_x[0].address); 3330 pci_unmap_single(acb->dev, srb->segment_x[0].address, 3331 srb->segment_x[0].length, PCI_DMA_FROMDEVICE); 3332 /* Restore SG stuff */ 3333 srb->total_xfer_length = srb->xferred; 3334 srb->segment_x[0].address = 3335 srb->segment_x[DC395x_MAX_SG_LISTENTRY - 1].address; 3336 srb->segment_x[0].length = 3337 srb->segment_x[DC395x_MAX_SG_LISTENTRY - 1].length; 3338 } 3339 3340 3341 /* 3342 * Complete execution of a SCSI command 3343 * Signal completion to the generic SCSI driver 3344 */ 3345 static void srb_done(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 3346 struct ScsiReqBlk *srb) 3347 { 3348 u8 tempcnt, status; 3349 struct scsi_cmnd *cmd = srb->cmd; 3350 enum dma_data_direction dir = cmd->sc_data_direction; 3351 int ckc_only = 1; 3352 3353 dprintkdbg(DBG_1, "srb_done: (pid#%li) <%02i-%i>\n", srb->cmd->pid, 3354 srb->cmd->device->id, srb->cmd->device->lun); 3355 dprintkdbg(DBG_SG, "srb_done: srb=%p sg=%i(%i/%i) buf=%p\n", 3356 srb, cmd->use_sg, srb->sg_index, srb->sg_count, 3357 cmd->request_buffer); 3358 status = srb->target_status; 3359 if (srb->flag & AUTO_REQSENSE) { 3360 dprintkdbg(DBG_0, "srb_done: AUTO_REQSENSE1\n"); 3361 pci_unmap_srb_sense(acb, srb); 3362 /* 3363 ** target status.......................... 3364 */ 3365 srb->flag &= ~AUTO_REQSENSE; 3366 srb->adapter_status = 0; 3367 srb->target_status = CHECK_CONDITION << 1; 3368 if (debug_enabled(DBG_1)) { 3369 switch (cmd->sense_buffer[2] & 0x0f) { 3370 case NOT_READY: 3371 dprintkl(KERN_DEBUG, 3372 "ReqSense: NOT_READY cmnd=0x%02x <%02i-%i> stat=%i scan=%i ", 3373 cmd->cmnd[0], dcb->target_id, 3374 dcb->target_lun, status, acb->scan_devices); 3375 break; 3376 case UNIT_ATTENTION: 3377 dprintkl(KERN_DEBUG, 3378 "ReqSense: UNIT_ATTENTION cmnd=0x%02x <%02i-%i> stat=%i scan=%i ", 3379 cmd->cmnd[0], dcb->target_id, 3380 dcb->target_lun, status, acb->scan_devices); 3381 break; 3382 case ILLEGAL_REQUEST: 3383 dprintkl(KERN_DEBUG, 3384 "ReqSense: ILLEGAL_REQUEST cmnd=0x%02x <%02i-%i> stat=%i scan=%i ", 3385 cmd->cmnd[0], dcb->target_id, 3386 dcb->target_lun, status, acb->scan_devices); 3387 break; 3388 case MEDIUM_ERROR: 3389 dprintkl(KERN_DEBUG, 3390 "ReqSense: MEDIUM_ERROR cmnd=0x%02x <%02i-%i> stat=%i scan=%i ", 3391 cmd->cmnd[0], dcb->target_id, 3392 dcb->target_lun, status, acb->scan_devices); 3393 break; 3394 case HARDWARE_ERROR: 3395 dprintkl(KERN_DEBUG, 3396 "ReqSense: HARDWARE_ERROR cmnd=0x%02x <%02i-%i> stat=%i scan=%i ", 3397 cmd->cmnd[0], dcb->target_id, 3398 dcb->target_lun, status, acb->scan_devices); 3399 break; 3400 } 3401 if (cmd->sense_buffer[7] >= 6) 3402 printk("sense=0x%02x ASC=0x%02x ASCQ=0x%02x " 3403 "(0x%08x 0x%08x)\n", 3404 cmd->sense_buffer[2], cmd->sense_buffer[12], 3405 cmd->sense_buffer[13], 3406 *((unsigned int *)(cmd->sense_buffer + 3)), 3407 *((unsigned int *)(cmd->sense_buffer + 8))); 3408 else 3409 printk("sense=0x%02x No ASC/ASCQ (0x%08x)\n", 3410 cmd->sense_buffer[2], 3411 *((unsigned int *)(cmd->sense_buffer + 3))); 3412 } 3413 3414 if (status == (CHECK_CONDITION << 1)) { 3415 cmd->result = DID_BAD_TARGET << 16; 3416 goto ckc_e; 3417 } 3418 dprintkdbg(DBG_0, "srb_done: AUTO_REQSENSE2\n"); 3419 3420 if (srb->total_xfer_length 3421 && srb->total_xfer_length >= cmd->underflow) 3422 cmd->result = 3423 MK_RES_LNX(DRIVER_SENSE, DID_OK, 3424 srb->end_message, CHECK_CONDITION); 3425 /*SET_RES_DID(cmd->result,DID_OK) */ 3426 else 3427 cmd->result = 3428 MK_RES_LNX(DRIVER_SENSE, DID_OK, 3429 srb->end_message, CHECK_CONDITION); 3430 3431 goto ckc_e; 3432 } 3433 3434 /*************************************************************/ 3435 if (status) { 3436 /* 3437 * target status.......................... 3438 */ 3439 if (status_byte(status) == CHECK_CONDITION) { 3440 request_sense(acb, dcb, srb); 3441 return; 3442 } else if (status_byte(status) == QUEUE_FULL) { 3443 tempcnt = (u8)list_size(&dcb->srb_going_list); 3444 dprintkl(KERN_INFO, "QUEUE_FULL for dev <%02i-%i> with %i cmnds\n", 3445 dcb->target_id, dcb->target_lun, tempcnt); 3446 if (tempcnt > 1) 3447 tempcnt--; 3448 dcb->max_command = tempcnt; 3449 free_tag(dcb, srb); 3450 srb_going_to_waiting_move(dcb, srb); 3451 waiting_set_timer(acb, HZ / 20); 3452 srb->adapter_status = 0; 3453 srb->target_status = 0; 3454 return; 3455 } else if (status == SCSI_STAT_SEL_TIMEOUT) { 3456 srb->adapter_status = H_SEL_TIMEOUT; 3457 srb->target_status = 0; 3458 cmd->result = DID_NO_CONNECT << 16; 3459 } else { 3460 srb->adapter_status = 0; 3461 SET_RES_DID(cmd->result, DID_ERROR); 3462 SET_RES_MSG(cmd->result, srb->end_message); 3463 SET_RES_TARGET(cmd->result, status); 3464 3465 } 3466 } else { 3467 /* 3468 ** process initiator status.......................... 3469 */ 3470 status = srb->adapter_status; 3471 if (status & H_OVER_UNDER_RUN) { 3472 srb->target_status = 0; 3473 SET_RES_DID(cmd->result, DID_OK); 3474 SET_RES_MSG(cmd->result, srb->end_message); 3475 } else if (srb->status & PARITY_ERROR) { 3476 SET_RES_DID(cmd->result, DID_PARITY); 3477 SET_RES_MSG(cmd->result, srb->end_message); 3478 } else { /* No error */ 3479 3480 srb->adapter_status = 0; 3481 srb->target_status = 0; 3482 SET_RES_DID(cmd->result, DID_OK); 3483 } 3484 } 3485 3486 if (dir != PCI_DMA_NONE) { 3487 if (cmd->use_sg) 3488 pci_dma_sync_sg_for_cpu(acb->dev, 3489 (struct scatterlist *)cmd-> 3490 request_buffer, cmd->use_sg, dir); 3491 else if (cmd->request_buffer) 3492 pci_dma_sync_single_for_cpu(acb->dev, 3493 srb->segment_x[0].address, 3494 cmd->request_bufflen, dir); 3495 } 3496 ckc_only = 0; 3497 /* Check Error Conditions */ 3498 ckc_e: 3499 3500 if (cmd->cmnd[0] == INQUIRY) { 3501 unsigned char *base = NULL; 3502 struct ScsiInqData *ptr; 3503 unsigned long flags = 0; 3504 3505 if (cmd->use_sg) { 3506 struct scatterlist* sg = (struct scatterlist *)cmd->request_buffer; 3507 size_t offset = 0, len = sizeof(struct ScsiInqData); 3508 3509 local_irq_save(flags); 3510 base = scsi_kmap_atomic_sg(sg, cmd->use_sg, &offset, &len); 3511 ptr = (struct ScsiInqData *)(base + offset); 3512 } else 3513 ptr = (struct ScsiInqData *)(cmd->request_buffer); 3514 3515 if (!ckc_only && (cmd->result & RES_DID) == 0 3516 && cmd->cmnd[2] == 0 && cmd->request_bufflen >= 8 3517 && dir != PCI_DMA_NONE && ptr && (ptr->Vers & 0x07) >= 2) 3518 dcb->inquiry7 = ptr->Flags; 3519 3520 /*if( srb->cmd->cmnd[0] == INQUIRY && */ 3521 /* (host_byte(cmd->result) == DID_OK || status_byte(cmd->result) & CHECK_CONDITION) ) */ 3522 if ((cmd->result == (DID_OK << 16) 3523 || status_byte(cmd->result) & 3524 CHECK_CONDITION)) { 3525 if (!dcb->init_tcq_flag) { 3526 add_dev(acb, dcb, ptr); 3527 dcb->init_tcq_flag = 1; 3528 } 3529 } 3530 3531 if (cmd->use_sg) { 3532 scsi_kunmap_atomic_sg(base); 3533 local_irq_restore(flags); 3534 } 3535 } 3536 3537 /* Here is the info for Doug Gilbert's sg3 ... */ 3538 cmd->resid = srb->total_xfer_length; 3539 /* This may be interpreted by sb. or not ... */ 3540 cmd->SCp.this_residual = srb->total_xfer_length; 3541 cmd->SCp.buffers_residual = 0; 3542 if (debug_enabled(DBG_KG)) { 3543 if (srb->total_xfer_length) 3544 dprintkdbg(DBG_KG, "srb_done: (pid#%li) <%02i-%i> " 3545 "cmnd=0x%02x Missed %i bytes\n", 3546 cmd->pid, cmd->device->id, cmd->device->lun, 3547 cmd->cmnd[0], srb->total_xfer_length); 3548 } 3549 3550 srb_going_remove(dcb, srb); 3551 /* Add to free list */ 3552 if (srb == acb->tmp_srb) 3553 dprintkl(KERN_ERR, "srb_done: ERROR! Completed cmd with tmp_srb\n"); 3554 else { 3555 dprintkdbg(DBG_0, "srb_done: (pid#%li) done result=0x%08x\n", 3556 cmd->pid, cmd->result); 3557 srb_free_insert(acb, srb); 3558 } 3559 pci_unmap_srb(acb, srb); 3560 3561 cmd->scsi_done(cmd); 3562 waiting_process_next(acb); 3563 } 3564 3565 3566 /* abort all cmds in our queues */ 3567 static void doing_srb_done(struct AdapterCtlBlk *acb, u8 did_flag, 3568 struct scsi_cmnd *cmd, u8 force) 3569 { 3570 struct DeviceCtlBlk *dcb; 3571 dprintkl(KERN_INFO, "doing_srb_done: pids "); 3572 3573 list_for_each_entry(dcb, &acb->dcb_list, list) { 3574 struct ScsiReqBlk *srb; 3575 struct ScsiReqBlk *tmp; 3576 struct scsi_cmnd *p; 3577 3578 list_for_each_entry_safe(srb, tmp, &dcb->srb_going_list, list) { 3579 enum dma_data_direction dir; 3580 int result; 3581 3582 p = srb->cmd; 3583 dir = p->sc_data_direction; 3584 result = MK_RES(0, did_flag, 0, 0); 3585 printk("G:%li(%02i-%i) ", p->pid, 3586 p->device->id, p->device->lun); 3587 srb_going_remove(dcb, srb); 3588 free_tag(dcb, srb); 3589 srb_free_insert(acb, srb); 3590 p->result = result; 3591 pci_unmap_srb_sense(acb, srb); 3592 pci_unmap_srb(acb, srb); 3593 if (force) { 3594 /* For new EH, we normally don't need to give commands back, 3595 * as they all complete or all time out */ 3596 p->scsi_done(p); 3597 } 3598 } 3599 if (!list_empty(&dcb->srb_going_list)) 3600 dprintkl(KERN_DEBUG, 3601 "How could the ML send cmnds to the Going queue? <%02i-%i>\n", 3602 dcb->target_id, dcb->target_lun); 3603 if (dcb->tag_mask) 3604 dprintkl(KERN_DEBUG, 3605 "tag_mask for <%02i-%i> should be empty, is %08x!\n", 3606 dcb->target_id, dcb->target_lun, 3607 dcb->tag_mask); 3608 3609 /* Waiting queue */ 3610 list_for_each_entry_safe(srb, tmp, &dcb->srb_waiting_list, list) { 3611 int result; 3612 p = srb->cmd; 3613 3614 result = MK_RES(0, did_flag, 0, 0); 3615 printk("W:%li<%02i-%i>", p->pid, p->device->id, 3616 p->device->lun); 3617 srb_waiting_remove(dcb, srb); 3618 srb_free_insert(acb, srb); 3619 p->result = result; 3620 pci_unmap_srb_sense(acb, srb); 3621 pci_unmap_srb(acb, srb); 3622 if (force) { 3623 /* For new EH, we normally don't need to give commands back, 3624 * as they all complete or all time out */ 3625 cmd->scsi_done(cmd); 3626 } 3627 } 3628 if (!list_empty(&dcb->srb_waiting_list)) 3629 dprintkl(KERN_DEBUG, "ML queued %i cmnds again to <%02i-%i>\n", 3630 list_size(&dcb->srb_waiting_list), dcb->target_id, 3631 dcb->target_lun); 3632 dcb->flag &= ~ABORT_DEV_; 3633 } 3634 printk("\n"); 3635 } 3636 3637 3638 static void reset_scsi_bus(struct AdapterCtlBlk *acb) 3639 { 3640 dprintkdbg(DBG_0, "reset_scsi_bus: acb=%p\n", acb); 3641 acb->acb_flag |= RESET_DEV; /* RESET_DETECT, RESET_DONE, RESET_DEV */ 3642 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_RSTSCSI); 3643 3644 while (!(DC395x_read8(acb, TRM_S1040_SCSI_INTSTATUS) & INT_SCSIRESET)) 3645 /* nothing */; 3646 } 3647 3648 3649 static void set_basic_config(struct AdapterCtlBlk *acb) 3650 { 3651 u8 bval; 3652 u16 wval; 3653 DC395x_write8(acb, TRM_S1040_SCSI_TIMEOUT, acb->sel_timeout); 3654 if (acb->config & HCC_PARITY) 3655 bval = PHASELATCH | INITIATOR | BLOCKRST | PARITYCHECK; 3656 else 3657 bval = PHASELATCH | INITIATOR | BLOCKRST; 3658 3659 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG0, bval); 3660 3661 /* program configuration 1: Act_Neg (+ Act_Neg_Enh? + Fast_Filter? + DataDis?) */ 3662 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG1, 0x03); /* was 0x13: default */ 3663 /* program Host ID */ 3664 DC395x_write8(acb, TRM_S1040_SCSI_HOSTID, acb->scsi_host->this_id); 3665 /* set ansynchronous transfer */ 3666 DC395x_write8(acb, TRM_S1040_SCSI_OFFSET, 0x00); 3667 /* Turn LED control off */ 3668 wval = DC395x_read16(acb, TRM_S1040_GEN_CONTROL) & 0x7F; 3669 DC395x_write16(acb, TRM_S1040_GEN_CONTROL, wval); 3670 /* DMA config */ 3671 wval = DC395x_read16(acb, TRM_S1040_DMA_CONFIG) & ~DMA_FIFO_CTRL; 3672 wval |= 3673 DMA_FIFO_HALF_HALF | DMA_ENHANCE /*| DMA_MEM_MULTI_READ */ ; 3674 DC395x_write16(acb, TRM_S1040_DMA_CONFIG, wval); 3675 /* Clear pending interrupt status */ 3676 DC395x_read8(acb, TRM_S1040_SCSI_INTSTATUS); 3677 /* Enable SCSI interrupt */ 3678 DC395x_write8(acb, TRM_S1040_SCSI_INTEN, 0x7F); 3679 DC395x_write8(acb, TRM_S1040_DMA_INTEN, EN_SCSIINTR | EN_DMAXFERERROR 3680 /*| EN_DMAXFERABORT | EN_DMAXFERCOMP | EN_FORCEDMACOMP */ 3681 ); 3682 } 3683 3684 3685 static void scsi_reset_detect(struct AdapterCtlBlk *acb) 3686 { 3687 dprintkl(KERN_INFO, "scsi_reset_detect: acb=%p\n", acb); 3688 /* delay half a second */ 3689 if (timer_pending(&acb->waiting_timer)) 3690 del_timer(&acb->waiting_timer); 3691 3692 DC395x_write8(acb, TRM_S1040_SCSI_CONTROL, DO_RSTMODULE); 3693 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, DMARESETMODULE); 3694 /*DC395x_write8(acb, TRM_S1040_DMA_CONTROL,STOPDMAXFER); */ 3695 udelay(500); 3696 /* Maybe we locked up the bus? Then lets wait even longer ... */ 3697 acb->scsi_host->last_reset = 3698 jiffies + 5 * HZ / 2 + 3699 HZ * acb->eeprom.delay_time; 3700 3701 clear_fifo(acb, "scsi_reset_detect"); 3702 set_basic_config(acb); 3703 /*1.25 */ 3704 /*DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_HWRESELECT); */ 3705 3706 if (acb->acb_flag & RESET_DEV) { /* RESET_DETECT, RESET_DONE, RESET_DEV */ 3707 acb->acb_flag |= RESET_DONE; 3708 } else { 3709 acb->acb_flag |= RESET_DETECT; 3710 reset_dev_param(acb); 3711 doing_srb_done(acb, DID_RESET, NULL, 1); 3712 /*DC395x_RecoverSRB( acb ); */ 3713 acb->active_dcb = NULL; 3714 acb->acb_flag = 0; 3715 waiting_process_next(acb); 3716 } 3717 } 3718 3719 3720 static void request_sense(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 3721 struct ScsiReqBlk *srb) 3722 { 3723 struct scsi_cmnd *cmd = srb->cmd; 3724 dprintkdbg(DBG_1, "request_sense: (pid#%li) <%02i-%i>\n", 3725 cmd->pid, cmd->device->id, cmd->device->lun); 3726 3727 srb->flag |= AUTO_REQSENSE; 3728 srb->adapter_status = 0; 3729 srb->target_status = 0; 3730 3731 /* KG: Can this prevent crap sense data ? */ 3732 memset(cmd->sense_buffer, 0, sizeof(cmd->sense_buffer)); 3733 3734 /* Save some data */ 3735 srb->segment_x[DC395x_MAX_SG_LISTENTRY - 1].address = 3736 srb->segment_x[0].address; 3737 srb->segment_x[DC395x_MAX_SG_LISTENTRY - 1].length = 3738 srb->segment_x[0].length; 3739 srb->xferred = srb->total_xfer_length; 3740 /* srb->segment_x : a one entry of S/G list table */ 3741 srb->total_xfer_length = sizeof(cmd->sense_buffer); 3742 srb->segment_x[0].length = sizeof(cmd->sense_buffer); 3743 /* Map sense buffer */ 3744 srb->segment_x[0].address = 3745 pci_map_single(acb->dev, cmd->sense_buffer, 3746 sizeof(cmd->sense_buffer), PCI_DMA_FROMDEVICE); 3747 dprintkdbg(DBG_SG, "request_sense: map buffer %p->%08x(%05x)\n", 3748 cmd->sense_buffer, srb->segment_x[0].address, 3749 sizeof(cmd->sense_buffer)); 3750 srb->sg_count = 1; 3751 srb->sg_index = 0; 3752 3753 if (start_scsi(acb, dcb, srb)) { /* Should only happen, if sb. else grabs the bus */ 3754 dprintkl(KERN_DEBUG, 3755 "request_sense: (pid#%li) failed <%02i-%i>\n", 3756 srb->cmd->pid, dcb->target_id, dcb->target_lun); 3757 srb_going_to_waiting_move(dcb, srb); 3758 waiting_set_timer(acb, HZ / 100); 3759 } 3760 } 3761 3762 3763 /** 3764 * device_alloc - Allocate a new device instance. This create the 3765 * devices instance and sets up all the data items. The adapter 3766 * instance is required to obtain confiuration information for this 3767 * device. This does *not* add this device to the adapters device 3768 * list. 3769 * 3770 * @acb: The adapter to obtain configuration information from. 3771 * @target: The target for the new device. 3772 * @lun: The lun for the new device. 3773 * 3774 * Return the new device if successful or NULL on failure. 3775 **/ 3776 static struct DeviceCtlBlk *device_alloc(struct AdapterCtlBlk *acb, 3777 u8 target, u8 lun) 3778 { 3779 struct NvRamType *eeprom = &acb->eeprom; 3780 u8 period_index = eeprom->target[target].period & 0x07; 3781 struct DeviceCtlBlk *dcb; 3782 3783 dcb = kmalloc(sizeof(struct DeviceCtlBlk), GFP_ATOMIC); 3784 dprintkdbg(DBG_0, "device_alloc: <%02i-%i>\n", target, lun); 3785 if (!dcb) 3786 return NULL; 3787 dcb->acb = NULL; 3788 INIT_LIST_HEAD(&dcb->srb_going_list); 3789 INIT_LIST_HEAD(&dcb->srb_waiting_list); 3790 dcb->active_srb = NULL; 3791 dcb->tag_mask = 0; 3792 dcb->max_command = 1; 3793 dcb->target_id = target; 3794 dcb->target_lun = lun; 3795 #ifndef DC395x_NO_DISCONNECT 3796 dcb->identify_msg = 3797 IDENTIFY(dcb->dev_mode & NTC_DO_DISCONNECT, lun); 3798 #else 3799 dcb->identify_msg = IDENTIFY(0, lun); 3800 #endif 3801 dcb->dev_mode = eeprom->target[target].cfg0; 3802 dcb->inquiry7 = 0; 3803 dcb->sync_mode = 0; 3804 dcb->min_nego_period = clock_period[period_index]; 3805 dcb->sync_period = 0; 3806 dcb->sync_offset = 0; 3807 dcb->flag = 0; 3808 3809 #ifndef DC395x_NO_WIDE 3810 if ((dcb->dev_mode & NTC_DO_WIDE_NEGO) 3811 && (acb->config & HCC_WIDE_CARD)) 3812 dcb->sync_mode |= WIDE_NEGO_ENABLE; 3813 #endif 3814 #ifndef DC395x_NO_SYNC 3815 if (dcb->dev_mode & NTC_DO_SYNC_NEGO) 3816 if (!(lun) || current_sync_offset) 3817 dcb->sync_mode |= SYNC_NEGO_ENABLE; 3818 #endif 3819 if (dcb->target_lun != 0) { 3820 /* Copy settings */ 3821 struct DeviceCtlBlk *p; 3822 list_for_each_entry(p, &acb->dcb_list, list) 3823 if (p->target_id == dcb->target_id) 3824 break; 3825 dprintkdbg(DBG_1, 3826 "device_alloc: <%02i-%i> copy from <%02i-%i>\n", 3827 dcb->target_id, dcb->target_lun, 3828 p->target_id, p->target_lun); 3829 dcb->sync_mode = p->sync_mode; 3830 dcb->sync_period = p->sync_period; 3831 dcb->min_nego_period = p->min_nego_period; 3832 dcb->sync_offset = p->sync_offset; 3833 dcb->inquiry7 = p->inquiry7; 3834 } 3835 return dcb; 3836 } 3837 3838 3839 /** 3840 * adapter_add_device - Adds the device instance to the adaptor instance. 3841 * 3842 * @acb: The adapter device to be updated 3843 * @dcb: A newly created and intialised device instance to add. 3844 **/ 3845 static void adapter_add_device(struct AdapterCtlBlk *acb, 3846 struct DeviceCtlBlk *dcb) 3847 { 3848 /* backpointer to adapter */ 3849 dcb->acb = acb; 3850 3851 /* set run_robin to this device if it is currently empty */ 3852 if (list_empty(&acb->dcb_list)) 3853 acb->dcb_run_robin = dcb; 3854 3855 /* add device to list */ 3856 list_add_tail(&dcb->list, &acb->dcb_list); 3857 3858 /* update device maps */ 3859 acb->dcb_map[dcb->target_id] |= (1 << dcb->target_lun); 3860 acb->children[dcb->target_id][dcb->target_lun] = dcb; 3861 } 3862 3863 3864 /** 3865 * adapter_remove_device - Removes the device instance from the adaptor 3866 * instance. The device instance is not check in any way or freed by this. 3867 * The caller is expected to take care of that. This will simply remove the 3868 * device from the adapters data strcutures. 3869 * 3870 * @acb: The adapter device to be updated 3871 * @dcb: A device that has previously been added to the adapter. 3872 **/ 3873 static void adapter_remove_device(struct AdapterCtlBlk *acb, 3874 struct DeviceCtlBlk *dcb) 3875 { 3876 struct DeviceCtlBlk *i; 3877 struct DeviceCtlBlk *tmp; 3878 dprintkdbg(DBG_0, "adapter_remove_device: <%02i-%i>\n", 3879 dcb->target_id, dcb->target_lun); 3880 3881 /* fix up any pointers to this device that we have in the adapter */ 3882 if (acb->active_dcb == dcb) 3883 acb->active_dcb = NULL; 3884 if (acb->dcb_run_robin == dcb) 3885 acb->dcb_run_robin = dcb_get_next(&acb->dcb_list, dcb); 3886 3887 /* unlink from list */ 3888 list_for_each_entry_safe(i, tmp, &acb->dcb_list, list) 3889 if (dcb == i) { 3890 list_del(&i->list); 3891 break; 3892 } 3893 3894 /* clear map and children */ 3895 acb->dcb_map[dcb->target_id] &= ~(1 << dcb->target_lun); 3896 acb->children[dcb->target_id][dcb->target_lun] = NULL; 3897 dcb->acb = NULL; 3898 } 3899 3900 3901 /** 3902 * adapter_remove_and_free_device - Removes a single device from the adapter 3903 * and then frees the device information. 3904 * 3905 * @acb: The adapter device to be updated 3906 * @dcb: A device that has previously been added to the adapter. 3907 */ 3908 static void adapter_remove_and_free_device(struct AdapterCtlBlk *acb, 3909 struct DeviceCtlBlk *dcb) 3910 { 3911 if (list_size(&dcb->srb_going_list) > 1) { 3912 dprintkdbg(DBG_1, "adapter_remove_and_free_device: <%02i-%i> " 3913 "Won't remove because of %i active requests.\n", 3914 dcb->target_id, dcb->target_lun, 3915 list_size(&dcb->srb_going_list)); 3916 return; 3917 } 3918 adapter_remove_device(acb, dcb); 3919 kfree(dcb); 3920 } 3921 3922 3923 /** 3924 * adapter_remove_and_free_all_devices - Removes and frees all of the 3925 * devices associated with the specified adapter. 3926 * 3927 * @acb: The adapter from which all devices should be removed. 3928 **/ 3929 static void adapter_remove_and_free_all_devices(struct AdapterCtlBlk* acb) 3930 { 3931 struct DeviceCtlBlk *dcb; 3932 struct DeviceCtlBlk *tmp; 3933 dprintkdbg(DBG_1, "adapter_remove_and_free_all_devices: num=%i\n", 3934 list_size(&acb->dcb_list)); 3935 3936 list_for_each_entry_safe(dcb, tmp, &acb->dcb_list, list) 3937 adapter_remove_and_free_device(acb, dcb); 3938 } 3939 3940 3941 /** 3942 * dc395x_slave_alloc - Called by the scsi mid layer to tell us about a new 3943 * scsi device that we need to deal with. We allocate a new device and then 3944 * insert that device into the adapters device list. 3945 * 3946 * @scsi_device: The new scsi device that we need to handle. 3947 **/ 3948 static int dc395x_slave_alloc(struct scsi_device *scsi_device) 3949 { 3950 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)scsi_device->host->hostdata; 3951 struct DeviceCtlBlk *dcb; 3952 3953 dcb = device_alloc(acb, scsi_device->id, scsi_device->lun); 3954 if (!dcb) 3955 return -ENOMEM; 3956 adapter_add_device(acb, dcb); 3957 3958 return 0; 3959 } 3960 3961 3962 /** 3963 * dc395x_slave_destroy - Called by the scsi mid layer to tell us about a 3964 * device that is going away. 3965 * 3966 * @scsi_device: The new scsi device that we need to handle. 3967 **/ 3968 static void dc395x_slave_destroy(struct scsi_device *scsi_device) 3969 { 3970 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)scsi_device->host->hostdata; 3971 struct DeviceCtlBlk *dcb = find_dcb(acb, scsi_device->id, scsi_device->lun); 3972 if (dcb) 3973 adapter_remove_and_free_device(acb, dcb); 3974 } 3975 3976 3977 3978 3979 /** 3980 * trms1040_wait_30us: wait for 30 us 3981 * 3982 * Waits for 30us (using the chip by the looks of it..) 3983 * 3984 * @io_port: base I/O address 3985 **/ 3986 static void __devinit trms1040_wait_30us(unsigned long io_port) 3987 { 3988 /* ScsiPortStallExecution(30); wait 30 us */ 3989 outb(5, io_port + TRM_S1040_GEN_TIMER); 3990 while (!(inb(io_port + TRM_S1040_GEN_STATUS) & GTIMEOUT)) 3991 /* nothing */ ; 3992 } 3993 3994 3995 /** 3996 * trms1040_write_cmd - write the secified command and address to 3997 * chip 3998 * 3999 * @io_port: base I/O address 4000 * @cmd: SB + op code (command) to send 4001 * @addr: address to send 4002 **/ 4003 static void __devinit trms1040_write_cmd(unsigned long io_port, u8 cmd, u8 addr) 4004 { 4005 int i; 4006 u8 send_data; 4007 4008 /* program SB + OP code */ 4009 for (i = 0; i < 3; i++, cmd <<= 1) { 4010 send_data = NVR_SELECT; 4011 if (cmd & 0x04) /* Start from bit 2 */ 4012 send_data |= NVR_BITOUT; 4013 4014 outb(send_data, io_port + TRM_S1040_GEN_NVRAM); 4015 trms1040_wait_30us(io_port); 4016 outb((send_data | NVR_CLOCK), 4017 io_port + TRM_S1040_GEN_NVRAM); 4018 trms1040_wait_30us(io_port); 4019 } 4020 4021 /* send address */ 4022 for (i = 0; i < 7; i++, addr <<= 1) { 4023 send_data = NVR_SELECT; 4024 if (addr & 0x40) /* Start from bit 6 */ 4025 send_data |= NVR_BITOUT; 4026 4027 outb(send_data, io_port + TRM_S1040_GEN_NVRAM); 4028 trms1040_wait_30us(io_port); 4029 outb((send_data | NVR_CLOCK), 4030 io_port + TRM_S1040_GEN_NVRAM); 4031 trms1040_wait_30us(io_port); 4032 } 4033 outb(NVR_SELECT, io_port + TRM_S1040_GEN_NVRAM); 4034 trms1040_wait_30us(io_port); 4035 } 4036 4037 4038 /** 4039 * trms1040_set_data - store a single byte in the eeprom 4040 * 4041 * Called from write all to write a single byte into the SSEEPROM 4042 * Which is done one bit at a time. 4043 * 4044 * @io_port: base I/O address 4045 * @addr: offset into EEPROM 4046 * @byte: bytes to write 4047 **/ 4048 static void __devinit trms1040_set_data(unsigned long io_port, u8 addr, u8 byte) 4049 { 4050 int i; 4051 u8 send_data; 4052 4053 /* Send write command & address */ 4054 trms1040_write_cmd(io_port, 0x05, addr); 4055 4056 /* Write data */ 4057 for (i = 0; i < 8; i++, byte <<= 1) { 4058 send_data = NVR_SELECT; 4059 if (byte & 0x80) /* Start from bit 7 */ 4060 send_data |= NVR_BITOUT; 4061 4062 outb(send_data, io_port + TRM_S1040_GEN_NVRAM); 4063 trms1040_wait_30us(io_port); 4064 outb((send_data | NVR_CLOCK), io_port + TRM_S1040_GEN_NVRAM); 4065 trms1040_wait_30us(io_port); 4066 } 4067 outb(NVR_SELECT, io_port + TRM_S1040_GEN_NVRAM); 4068 trms1040_wait_30us(io_port); 4069 4070 /* Disable chip select */ 4071 outb(0, io_port + TRM_S1040_GEN_NVRAM); 4072 trms1040_wait_30us(io_port); 4073 4074 outb(NVR_SELECT, io_port + TRM_S1040_GEN_NVRAM); 4075 trms1040_wait_30us(io_port); 4076 4077 /* Wait for write ready */ 4078 while (1) { 4079 outb((NVR_SELECT | NVR_CLOCK), io_port + TRM_S1040_GEN_NVRAM); 4080 trms1040_wait_30us(io_port); 4081 4082 outb(NVR_SELECT, io_port + TRM_S1040_GEN_NVRAM); 4083 trms1040_wait_30us(io_port); 4084 4085 if (inb(io_port + TRM_S1040_GEN_NVRAM) & NVR_BITIN) 4086 break; 4087 } 4088 4089 /* Disable chip select */ 4090 outb(0, io_port + TRM_S1040_GEN_NVRAM); 4091 } 4092 4093 4094 /** 4095 * trms1040_write_all - write 128 bytes to the eeprom 4096 * 4097 * Write the supplied 128 bytes to the chips SEEPROM 4098 * 4099 * @eeprom: the data to write 4100 * @io_port: the base io port 4101 **/ 4102 static void __devinit trms1040_write_all(struct NvRamType *eeprom, unsigned long io_port) 4103 { 4104 u8 *b_eeprom = (u8 *)eeprom; 4105 u8 addr; 4106 4107 /* Enable SEEPROM */ 4108 outb((inb(io_port + TRM_S1040_GEN_CONTROL) | EN_EEPROM), 4109 io_port + TRM_S1040_GEN_CONTROL); 4110 4111 /* write enable */ 4112 trms1040_write_cmd(io_port, 0x04, 0xFF); 4113 outb(0, io_port + TRM_S1040_GEN_NVRAM); 4114 trms1040_wait_30us(io_port); 4115 4116 /* write */ 4117 for (addr = 0; addr < 128; addr++, b_eeprom++) 4118 trms1040_set_data(io_port, addr, *b_eeprom); 4119 4120 /* write disable */ 4121 trms1040_write_cmd(io_port, 0x04, 0x00); 4122 outb(0, io_port + TRM_S1040_GEN_NVRAM); 4123 trms1040_wait_30us(io_port); 4124 4125 /* Disable SEEPROM */ 4126 outb((inb(io_port + TRM_S1040_GEN_CONTROL) & ~EN_EEPROM), 4127 io_port + TRM_S1040_GEN_CONTROL); 4128 } 4129 4130 4131 /** 4132 * trms1040_get_data - get a single byte from the eeprom 4133 * 4134 * Called from read all to read a single byte into the SSEEPROM 4135 * Which is done one bit at a time. 4136 * 4137 * @io_port: base I/O address 4138 * @addr: offset into SEEPROM 4139 * 4140 * Returns the the byte read. 4141 **/ 4142 static u8 __devinit trms1040_get_data(unsigned long io_port, u8 addr) 4143 { 4144 int i; 4145 u8 read_byte; 4146 u8 result = 0; 4147 4148 /* Send read command & address */ 4149 trms1040_write_cmd(io_port, 0x06, addr); 4150 4151 /* read data */ 4152 for (i = 0; i < 8; i++) { 4153 outb((NVR_SELECT | NVR_CLOCK), io_port + TRM_S1040_GEN_NVRAM); 4154 trms1040_wait_30us(io_port); 4155 outb(NVR_SELECT, io_port + TRM_S1040_GEN_NVRAM); 4156 4157 /* Get data bit while falling edge */ 4158 read_byte = inb(io_port + TRM_S1040_GEN_NVRAM); 4159 result <<= 1; 4160 if (read_byte & NVR_BITIN) 4161 result |= 1; 4162 4163 trms1040_wait_30us(io_port); 4164 } 4165 4166 /* Disable chip select */ 4167 outb(0, io_port + TRM_S1040_GEN_NVRAM); 4168 return result; 4169 } 4170 4171 4172 /** 4173 * trms1040_read_all - read all bytes from the eeprom 4174 * 4175 * Read the 128 bytes from the SEEPROM. 4176 * 4177 * @eeprom: where to store the data 4178 * @io_port: the base io port 4179 **/ 4180 static void __devinit trms1040_read_all(struct NvRamType *eeprom, unsigned long io_port) 4181 { 4182 u8 *b_eeprom = (u8 *)eeprom; 4183 u8 addr; 4184 4185 /* Enable SEEPROM */ 4186 outb((inb(io_port + TRM_S1040_GEN_CONTROL) | EN_EEPROM), 4187 io_port + TRM_S1040_GEN_CONTROL); 4188 4189 /* read details */ 4190 for (addr = 0; addr < 128; addr++, b_eeprom++) 4191 *b_eeprom = trms1040_get_data(io_port, addr); 4192 4193 /* Disable SEEPROM */ 4194 outb((inb(io_port + TRM_S1040_GEN_CONTROL) & ~EN_EEPROM), 4195 io_port + TRM_S1040_GEN_CONTROL); 4196 } 4197 4198 4199 4200 /** 4201 * check_eeprom - get and check contents of the eeprom 4202 * 4203 * Read seeprom 128 bytes into the memory provider in eeprom. 4204 * Checks the checksum and if it's not correct it uses a set of default 4205 * values. 4206 * 4207 * @eeprom: caller allocated strcuture to read the eeprom data into 4208 * @io_port: io port to read from 4209 **/ 4210 static void __devinit check_eeprom(struct NvRamType *eeprom, unsigned long io_port) 4211 { 4212 u16 *w_eeprom = (u16 *)eeprom; 4213 u16 w_addr; 4214 u16 cksum; 4215 u32 d_addr; 4216 u32 *d_eeprom; 4217 4218 trms1040_read_all(eeprom, io_port); /* read eeprom */ 4219 4220 cksum = 0; 4221 for (w_addr = 0, w_eeprom = (u16 *)eeprom; w_addr < 64; 4222 w_addr++, w_eeprom++) 4223 cksum += *w_eeprom; 4224 if (cksum != 0x1234) { 4225 /* 4226 * Checksum is wrong. 4227 * Load a set of defaults into the eeprom buffer 4228 */ 4229 dprintkl(KERN_WARNING, 4230 "EEProm checksum error: using default values and options.\n"); 4231 eeprom->sub_vendor_id[0] = (u8)PCI_VENDOR_ID_TEKRAM; 4232 eeprom->sub_vendor_id[1] = (u8)(PCI_VENDOR_ID_TEKRAM >> 8); 4233 eeprom->sub_sys_id[0] = (u8)PCI_DEVICE_ID_TEKRAM_TRMS1040; 4234 eeprom->sub_sys_id[1] = 4235 (u8)(PCI_DEVICE_ID_TEKRAM_TRMS1040 >> 8); 4236 eeprom->sub_class = 0x00; 4237 eeprom->vendor_id[0] = (u8)PCI_VENDOR_ID_TEKRAM; 4238 eeprom->vendor_id[1] = (u8)(PCI_VENDOR_ID_TEKRAM >> 8); 4239 eeprom->device_id[0] = (u8)PCI_DEVICE_ID_TEKRAM_TRMS1040; 4240 eeprom->device_id[1] = 4241 (u8)(PCI_DEVICE_ID_TEKRAM_TRMS1040 >> 8); 4242 eeprom->reserved = 0x00; 4243 4244 for (d_addr = 0, d_eeprom = (u32 *)eeprom->target; 4245 d_addr < 16; d_addr++, d_eeprom++) 4246 *d_eeprom = 0x00000077; /* cfg3,cfg2,period,cfg0 */ 4247 4248 *d_eeprom++ = 0x04000F07; /* max_tag,delay_time,channel_cfg,scsi_id */ 4249 *d_eeprom++ = 0x00000015; /* reserved1,boot_lun,boot_target,reserved0 */ 4250 for (d_addr = 0; d_addr < 12; d_addr++, d_eeprom++) 4251 *d_eeprom = 0x00; 4252 4253 /* Now load defaults (maybe set by boot/module params) */ 4254 set_safe_settings(); 4255 fix_settings(); 4256 eeprom_override(eeprom); 4257 4258 eeprom->cksum = 0x00; 4259 for (w_addr = 0, cksum = 0, w_eeprom = (u16 *)eeprom; 4260 w_addr < 63; w_addr++, w_eeprom++) 4261 cksum += *w_eeprom; 4262 4263 *w_eeprom = 0x1234 - cksum; 4264 trms1040_write_all(eeprom, io_port); 4265 eeprom->delay_time = cfg_data[CFG_RESET_DELAY].value; 4266 } else { 4267 set_safe_settings(); 4268 eeprom_index_to_delay(eeprom); 4269 eeprom_override(eeprom); 4270 } 4271 } 4272 4273 4274 /** 4275 * print_eeprom_settings - output the eeprom settings 4276 * to the kernel log so people can see what they were. 4277 * 4278 * @eeprom: The eeprom data strucutre to show details for. 4279 **/ 4280 static void __devinit print_eeprom_settings(struct NvRamType *eeprom) 4281 { 4282 dprintkl(KERN_INFO, "Used settings: AdapterID=%02i, Speed=%i(%02i.%01iMHz), dev_mode=0x%02x\n", 4283 eeprom->scsi_id, 4284 eeprom->target[0].period, 4285 clock_speed[eeprom->target[0].period] / 10, 4286 clock_speed[eeprom->target[0].period] % 10, 4287 eeprom->target[0].cfg0); 4288 dprintkl(KERN_INFO, " AdaptMode=0x%02x, Tags=%i(%02i), DelayReset=%is\n", 4289 eeprom->channel_cfg, eeprom->max_tag, 4290 1 << eeprom->max_tag, eeprom->delay_time); 4291 } 4292 4293 4294 /* Free SG tables */ 4295 static void adapter_sg_tables_free(struct AdapterCtlBlk *acb) 4296 { 4297 int i; 4298 const unsigned srbs_per_page = PAGE_SIZE/SEGMENTX_LEN; 4299 4300 for (i = 0; i < DC395x_MAX_SRB_CNT; i += srbs_per_page) 4301 kfree(acb->srb_array[i].segment_x); 4302 } 4303 4304 4305 /* 4306 * Allocate SG tables; as we have to pci_map them, an SG list (struct SGentry*) 4307 * should never cross a page boundary */ 4308 static int __devinit adapter_sg_tables_alloc(struct AdapterCtlBlk *acb) 4309 { 4310 const unsigned mem_needed = (DC395x_MAX_SRB_CNT+1) 4311 *SEGMENTX_LEN; 4312 int pages = (mem_needed+(PAGE_SIZE-1))/PAGE_SIZE; 4313 const unsigned srbs_per_page = PAGE_SIZE/SEGMENTX_LEN; 4314 int srb_idx = 0; 4315 unsigned i = 0; 4316 struct SGentry *ptr; 4317 4318 for (i = 0; i < DC395x_MAX_SRB_CNT; i++) 4319 acb->srb_array[i].segment_x = NULL; 4320 4321 dprintkdbg(DBG_1, "Allocate %i pages for SG tables\n", pages); 4322 while (pages--) { 4323 ptr = (struct SGentry *)kmalloc(PAGE_SIZE, GFP_KERNEL); 4324 if (!ptr) { 4325 adapter_sg_tables_free(acb); 4326 return 1; 4327 } 4328 dprintkdbg(DBG_1, "Allocate %li bytes at %p for SG segments %i\n", 4329 PAGE_SIZE, ptr, srb_idx); 4330 i = 0; 4331 while (i < srbs_per_page && srb_idx < DC395x_MAX_SRB_CNT) 4332 acb->srb_array[srb_idx++].segment_x = 4333 ptr + (i++ * DC395x_MAX_SG_LISTENTRY); 4334 } 4335 if (i < srbs_per_page) 4336 acb->srb.segment_x = 4337 ptr + (i * DC395x_MAX_SG_LISTENTRY); 4338 else 4339 dprintkl(KERN_DEBUG, "No space for tmsrb SG table reserved?!\n"); 4340 return 0; 4341 } 4342 4343 4344 4345 /** 4346 * adapter_print_config - print adapter connection and termination 4347 * config 4348 * 4349 * The io port in the adapter needs to have been set before calling 4350 * this function. 4351 * 4352 * @acb: The adapter to print the information for. 4353 **/ 4354 static void __devinit adapter_print_config(struct AdapterCtlBlk *acb) 4355 { 4356 u8 bval; 4357 4358 bval = DC395x_read8(acb, TRM_S1040_GEN_STATUS); 4359 dprintkl(KERN_INFO, "%sConnectors: ", 4360 ((bval & WIDESCSI) ? "(Wide) " : "")); 4361 if (!(bval & CON5068)) 4362 printk("ext%s ", !(bval & EXT68HIGH) ? "68" : "50"); 4363 if (!(bval & CON68)) 4364 printk("int68%s ", !(bval & INT68HIGH) ? "" : "(50)"); 4365 if (!(bval & CON50)) 4366 printk("int50 "); 4367 if ((bval & (CON5068 | CON50 | CON68)) == 4368 0 /*(CON5068 | CON50 | CON68) */ ) 4369 printk(" Oops! (All 3?) "); 4370 bval = DC395x_read8(acb, TRM_S1040_GEN_CONTROL); 4371 printk(" Termination: "); 4372 if (bval & DIS_TERM) 4373 printk("Disabled\n"); 4374 else { 4375 if (bval & AUTOTERM) 4376 printk("Auto "); 4377 if (bval & LOW8TERM) 4378 printk("Low "); 4379 if (bval & UP8TERM) 4380 printk("High "); 4381 printk("\n"); 4382 } 4383 } 4384 4385 4386 /** 4387 * adapter_init_params - Initialize the various parameters in the 4388 * adapter structure. Note that the pointer to the scsi_host is set 4389 * early (when this instance is created) and the io_port and irq 4390 * values are set later after they have been reserved. This just gets 4391 * everything set to a good starting position. 4392 * 4393 * The eeprom structure in the adapter needs to have been set before 4394 * calling this function. 4395 * 4396 * @acb: The adapter to initialize. 4397 **/ 4398 static void __devinit adapter_init_params(struct AdapterCtlBlk *acb) 4399 { 4400 struct NvRamType *eeprom = &acb->eeprom; 4401 int i; 4402 4403 /* NOTE: acb->scsi_host is set at scsi_host/acb creation time */ 4404 /* NOTE: acb->io_port_base is set at port registration time */ 4405 /* NOTE: acb->io_port_len is set at port registration time */ 4406 4407 INIT_LIST_HEAD(&acb->dcb_list); 4408 acb->dcb_run_robin = NULL; 4409 acb->active_dcb = NULL; 4410 4411 INIT_LIST_HEAD(&acb->srb_free_list); 4412 /* temp SRB for Q tag used or abort command used */ 4413 acb->tmp_srb = &acb->srb; 4414 init_timer(&acb->waiting_timer); 4415 init_timer(&acb->selto_timer); 4416 4417 acb->srb_count = DC395x_MAX_SRB_CNT; 4418 4419 acb->sel_timeout = DC395x_SEL_TIMEOUT; /* timeout=250ms */ 4420 /* NOTE: acb->irq_level is set at IRQ registration time */ 4421 4422 acb->tag_max_num = 1 << eeprom->max_tag; 4423 if (acb->tag_max_num > 30) 4424 acb->tag_max_num = 30; 4425 4426 acb->acb_flag = 0; /* RESET_DETECT, RESET_DONE, RESET_DEV */ 4427 acb->gmode2 = eeprom->channel_cfg; 4428 acb->config = 0; /* NOTE: actually set in adapter_init_chip */ 4429 4430 if (eeprom->channel_cfg & NAC_SCANLUN) 4431 acb->lun_chk = 1; 4432 acb->scan_devices = 1; 4433 4434 acb->scsi_host->this_id = eeprom->scsi_id; 4435 acb->hostid_bit = (1 << acb->scsi_host->this_id); 4436 4437 for (i = 0; i < DC395x_MAX_SCSI_ID; i++) 4438 acb->dcb_map[i] = 0; 4439 4440 acb->msg_len = 0; 4441 4442 /* link static array of srbs into the srb free list */ 4443 for (i = 0; i < acb->srb_count - 1; i++) 4444 srb_free_insert(acb, &acb->srb_array[i]); 4445 } 4446 4447 4448 /** 4449 * adapter_init_host - Initialize the scsi host instance based on 4450 * values that we have already stored in the adapter instance. There's 4451 * some mention that a lot of these are deprecated, so we won't use 4452 * them (we'll use the ones in the adapter instance) but we'll fill 4453 * them in in case something else needs them. 4454 * 4455 * The eeprom structure, irq and io ports in the adapter need to have 4456 * been set before calling this function. 4457 * 4458 * @host: The scsi host instance to fill in the values for. 4459 **/ 4460 static void __devinit adapter_init_scsi_host(struct Scsi_Host *host) 4461 { 4462 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)host->hostdata; 4463 struct NvRamType *eeprom = &acb->eeprom; 4464 4465 host->max_cmd_len = 24; 4466 host->can_queue = DC395x_MAX_CMD_QUEUE; 4467 host->cmd_per_lun = DC395x_MAX_CMD_PER_LUN; 4468 host->this_id = (int)eeprom->scsi_id; 4469 host->io_port = acb->io_port_base; 4470 host->n_io_port = acb->io_port_len; 4471 host->dma_channel = -1; 4472 host->unique_id = acb->io_port_base; 4473 host->irq = acb->irq_level; 4474 host->last_reset = jiffies; 4475 4476 host->max_id = 16; 4477 if (host->max_id - 1 == eeprom->scsi_id) 4478 host->max_id--; 4479 4480 #ifdef CONFIG_SCSI_MULTI_LUN 4481 if (eeprom->channel_cfg & NAC_SCANLUN) 4482 host->max_lun = 8; 4483 else 4484 host->max_lun = 1; 4485 #else 4486 host->max_lun = 1; 4487 #endif 4488 4489 } 4490 4491 4492 /** 4493 * adapter_init_chip - Get the chip into a know state and figure out 4494 * some of the settings that apply to this adapter. 4495 * 4496 * The io port in the adapter needs to have been set before calling 4497 * this function. The config will be configured correctly on return. 4498 * 4499 * @acb: The adapter which we are to init. 4500 **/ 4501 static void __devinit adapter_init_chip(struct AdapterCtlBlk *acb) 4502 { 4503 struct NvRamType *eeprom = &acb->eeprom; 4504 4505 /* Mask all the interrupt */ 4506 DC395x_write8(acb, TRM_S1040_DMA_INTEN, 0x00); 4507 DC395x_write8(acb, TRM_S1040_SCSI_INTEN, 0x00); 4508 4509 /* Reset SCSI module */ 4510 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_RSTMODULE); 4511 4512 /* Reset PCI/DMA module */ 4513 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, DMARESETMODULE); 4514 udelay(20); 4515 4516 /* program configuration 0 */ 4517 acb->config = HCC_AUTOTERM | HCC_PARITY; 4518 if (DC395x_read8(acb, TRM_S1040_GEN_STATUS) & WIDESCSI) 4519 acb->config |= HCC_WIDE_CARD; 4520 4521 if (eeprom->channel_cfg & NAC_POWERON_SCSI_RESET) 4522 acb->config |= HCC_SCSI_RESET; 4523 4524 if (acb->config & HCC_SCSI_RESET) { 4525 dprintkl(KERN_INFO, "Performing initial SCSI bus reset\n"); 4526 DC395x_write8(acb, TRM_S1040_SCSI_CONTROL, DO_RSTSCSI); 4527 4528 /*while (!( DC395x_read8(acb, TRM_S1040_SCSI_INTSTATUS) & INT_SCSIRESET )); */ 4529 /*spin_unlock_irq (&io_request_lock); */ 4530 udelay(500); 4531 4532 acb->scsi_host->last_reset = 4533 jiffies + HZ / 2 + 4534 HZ * acb->eeprom.delay_time; 4535 4536 /*spin_lock_irq (&io_request_lock); */ 4537 } 4538 } 4539 4540 4541 /** 4542 * init_adapter - Grab the resource for the card, setup the adapter 4543 * information, set the card into a known state, create the various 4544 * tables etc etc. This basically gets all adapter information all up 4545 * to date, intialised and gets the chip in sync with it. 4546 * 4547 * @host: This hosts adapter structure 4548 * @io_port: The base I/O port 4549 * @irq: IRQ 4550 * 4551 * Returns 0 if the initialization succeeds, any other value on 4552 * failure. 4553 **/ 4554 static int __devinit adapter_init(struct AdapterCtlBlk *acb, 4555 unsigned long io_port, u32 io_port_len, unsigned int irq) 4556 { 4557 if (!request_region(io_port, io_port_len, DC395X_NAME)) { 4558 dprintkl(KERN_ERR, "Failed to reserve IO region 0x%lx\n", io_port); 4559 goto failed; 4560 } 4561 /* store port base to indicate we have registered it */ 4562 acb->io_port_base = io_port; 4563 acb->io_port_len = io_port_len; 4564 4565 if (request_irq(irq, dc395x_interrupt, IRQF_SHARED, DC395X_NAME, acb)) { 4566 /* release the region we just claimed */ 4567 dprintkl(KERN_INFO, "Failed to register IRQ\n"); 4568 goto failed; 4569 } 4570 /* store irq to indicate we have registered it */ 4571 acb->irq_level = irq; 4572 4573 /* get eeprom configuration information and command line settings etc */ 4574 check_eeprom(&acb->eeprom, io_port); 4575 print_eeprom_settings(&acb->eeprom); 4576 4577 /* setup adapter control block */ 4578 adapter_init_params(acb); 4579 4580 /* display card connectors/termination settings */ 4581 adapter_print_config(acb); 4582 4583 if (adapter_sg_tables_alloc(acb)) { 4584 dprintkl(KERN_DEBUG, "Memory allocation for SG tables failed\n"); 4585 goto failed; 4586 } 4587 adapter_init_scsi_host(acb->scsi_host); 4588 adapter_init_chip(acb); 4589 set_basic_config(acb); 4590 4591 dprintkdbg(DBG_0, 4592 "adapter_init: acb=%p, pdcb_map=%p psrb_array=%p " 4593 "size{acb=0x%04x dcb=0x%04x srb=0x%04x}\n", 4594 acb, acb->dcb_map, acb->srb_array, sizeof(struct AdapterCtlBlk), 4595 sizeof(struct DeviceCtlBlk), sizeof(struct ScsiReqBlk)); 4596 return 0; 4597 4598 failed: 4599 if (acb->irq_level) 4600 free_irq(acb->irq_level, acb); 4601 if (acb->io_port_base) 4602 release_region(acb->io_port_base, acb->io_port_len); 4603 adapter_sg_tables_free(acb); 4604 4605 return 1; 4606 } 4607 4608 4609 /** 4610 * adapter_uninit_chip - cleanly shut down the scsi controller chip, 4611 * stopping all operations and disabling interrupt generation on the 4612 * card. 4613 * 4614 * @acb: The adapter which we are to shutdown. 4615 **/ 4616 static void adapter_uninit_chip(struct AdapterCtlBlk *acb) 4617 { 4618 /* disable interrupts */ 4619 DC395x_write8(acb, TRM_S1040_DMA_INTEN, 0); 4620 DC395x_write8(acb, TRM_S1040_SCSI_INTEN, 0); 4621 4622 /* reset the scsi bus */ 4623 if (acb->config & HCC_SCSI_RESET) 4624 reset_scsi_bus(acb); 4625 4626 /* clear any pending interupt state */ 4627 DC395x_read8(acb, TRM_S1040_SCSI_INTSTATUS); 4628 } 4629 4630 4631 4632 /** 4633 * adapter_uninit - Shut down the chip and release any resources that 4634 * we had allocated. Once this returns the adapter should not be used 4635 * anymore. 4636 * 4637 * @acb: The adapter which we are to un-initialize. 4638 **/ 4639 static void adapter_uninit(struct AdapterCtlBlk *acb) 4640 { 4641 unsigned long flags; 4642 DC395x_LOCK_IO(acb->scsi_host, flags); 4643 4644 /* remove timers */ 4645 if (timer_pending(&acb->waiting_timer)) 4646 del_timer(&acb->waiting_timer); 4647 if (timer_pending(&acb->selto_timer)) 4648 del_timer(&acb->selto_timer); 4649 4650 adapter_uninit_chip(acb); 4651 adapter_remove_and_free_all_devices(acb); 4652 DC395x_UNLOCK_IO(acb->scsi_host, flags); 4653 4654 if (acb->irq_level) 4655 free_irq(acb->irq_level, acb); 4656 if (acb->io_port_base) 4657 release_region(acb->io_port_base, acb->io_port_len); 4658 4659 adapter_sg_tables_free(acb); 4660 } 4661 4662 4663 #undef SPRINTF 4664 #define SPRINTF(args...) pos += sprintf(pos, args) 4665 4666 #undef YESNO 4667 #define YESNO(YN) \ 4668 if (YN) SPRINTF(" Yes ");\ 4669 else SPRINTF(" No ") 4670 4671 static int dc395x_proc_info(struct Scsi_Host *host, char *buffer, 4672 char **start, off_t offset, int length, int inout) 4673 { 4674 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)host->hostdata; 4675 int spd, spd1; 4676 char *pos = buffer; 4677 struct DeviceCtlBlk *dcb; 4678 unsigned long flags; 4679 int dev; 4680 4681 if (inout) /* Has data been written to the file ? */ 4682 return -EPERM; 4683 4684 SPRINTF(DC395X_BANNER " PCI SCSI Host Adapter\n"); 4685 SPRINTF(" Driver Version " DC395X_VERSION "\n"); 4686 4687 DC395x_LOCK_IO(acb->scsi_host, flags); 4688 4689 SPRINTF("SCSI Host Nr %i, ", host->host_no); 4690 SPRINTF("DC395U/UW/F DC315/U %s\n", 4691 (acb->config & HCC_WIDE_CARD) ? "Wide" : ""); 4692 SPRINTF("io_port_base 0x%04lx, ", acb->io_port_base); 4693 SPRINTF("irq_level 0x%04x, ", acb->irq_level); 4694 SPRINTF(" SelTimeout %ims\n", (1638 * acb->sel_timeout) / 1000); 4695 4696 SPRINTF("MaxID %i, MaxLUN %i, ", host->max_id, host->max_lun); 4697 SPRINTF("AdapterID %i\n", host->this_id); 4698 4699 SPRINTF("tag_max_num %i", acb->tag_max_num); 4700 /*SPRINTF(", DMA_Status %i\n", DC395x_read8(acb, TRM_S1040_DMA_STATUS)); */ 4701 SPRINTF(", FilterCfg 0x%02x", 4702 DC395x_read8(acb, TRM_S1040_SCSI_CONFIG1)); 4703 SPRINTF(", DelayReset %is\n", acb->eeprom.delay_time); 4704 /*SPRINTF("\n"); */ 4705 4706 SPRINTF("Nr of DCBs: %i\n", list_size(&acb->dcb_list)); 4707 SPRINTF 4708 ("Map of attached LUNs: %02x %02x %02x %02x %02x %02x %02x %02x\n", 4709 acb->dcb_map[0], acb->dcb_map[1], acb->dcb_map[2], 4710 acb->dcb_map[3], acb->dcb_map[4], acb->dcb_map[5], 4711 acb->dcb_map[6], acb->dcb_map[7]); 4712 SPRINTF 4713 (" %02x %02x %02x %02x %02x %02x %02x %02x\n", 4714 acb->dcb_map[8], acb->dcb_map[9], acb->dcb_map[10], 4715 acb->dcb_map[11], acb->dcb_map[12], acb->dcb_map[13], 4716 acb->dcb_map[14], acb->dcb_map[15]); 4717 4718 SPRINTF 4719 ("Un ID LUN Prty Sync Wide DsCn SndS TagQ nego_period SyncFreq SyncOffs MaxCmd\n"); 4720 4721 dev = 0; 4722 list_for_each_entry(dcb, &acb->dcb_list, list) { 4723 int nego_period; 4724 SPRINTF("%02i %02i %02i ", dev, dcb->target_id, 4725 dcb->target_lun); 4726 YESNO(dcb->dev_mode & NTC_DO_PARITY_CHK); 4727 YESNO(dcb->sync_offset); 4728 YESNO(dcb->sync_period & WIDE_SYNC); 4729 YESNO(dcb->dev_mode & NTC_DO_DISCONNECT); 4730 YESNO(dcb->dev_mode & NTC_DO_SEND_START); 4731 YESNO(dcb->sync_mode & EN_TAG_QUEUEING); 4732 nego_period = clock_period[dcb->sync_period & 0x07] << 2; 4733 if (dcb->sync_offset) 4734 SPRINTF(" %03i ns ", nego_period); 4735 else 4736 SPRINTF(" (%03i ns)", (dcb->min_nego_period << 2)); 4737 4738 if (dcb->sync_offset & 0x0f) { 4739 spd = 1000 / (nego_period); 4740 spd1 = 1000 % (nego_period); 4741 spd1 = (spd1 * 10 + nego_period / 2) / (nego_period); 4742 SPRINTF(" %2i.%1i M %02i ", spd, spd1, 4743 (dcb->sync_offset & 0x0f)); 4744 } else 4745 SPRINTF(" "); 4746 4747 /* Add more info ... */ 4748 SPRINTF(" %02i\n", dcb->max_command); 4749 dev++; 4750 } 4751 4752 if (timer_pending(&acb->waiting_timer)) 4753 SPRINTF("Waiting queue timer running\n"); 4754 else 4755 SPRINTF("\n"); 4756 4757 list_for_each_entry(dcb, &acb->dcb_list, list) { 4758 struct ScsiReqBlk *srb; 4759 if (!list_empty(&dcb->srb_waiting_list)) 4760 SPRINTF("DCB (%02i-%i): Waiting: %i:", 4761 dcb->target_id, dcb->target_lun, 4762 list_size(&dcb->srb_waiting_list)); 4763 list_for_each_entry(srb, &dcb->srb_waiting_list, list) 4764 SPRINTF(" %li", srb->cmd->pid); 4765 if (!list_empty(&dcb->srb_going_list)) 4766 SPRINTF("\nDCB (%02i-%i): Going : %i:", 4767 dcb->target_id, dcb->target_lun, 4768 list_size(&dcb->srb_going_list)); 4769 list_for_each_entry(srb, &dcb->srb_going_list, list) 4770 SPRINTF(" %li", srb->cmd->pid); 4771 if (!list_empty(&dcb->srb_waiting_list) || !list_empty(&dcb->srb_going_list)) 4772 SPRINTF("\n"); 4773 } 4774 4775 if (debug_enabled(DBG_1)) { 4776 SPRINTF("DCB list for ACB %p:\n", acb); 4777 list_for_each_entry(dcb, &acb->dcb_list, list) { 4778 SPRINTF("%p -> ", dcb); 4779 } 4780 SPRINTF("END\n"); 4781 } 4782 4783 *start = buffer + offset; 4784 DC395x_UNLOCK_IO(acb->scsi_host, flags); 4785 4786 if (pos - buffer < offset) 4787 return 0; 4788 else if (pos - buffer - offset < length) 4789 return pos - buffer - offset; 4790 else 4791 return length; 4792 } 4793 4794 4795 static struct scsi_host_template dc395x_driver_template = { 4796 .module = THIS_MODULE, 4797 .proc_name = DC395X_NAME, 4798 .proc_info = dc395x_proc_info, 4799 .name = DC395X_BANNER " " DC395X_VERSION, 4800 .queuecommand = dc395x_queue_command, 4801 .bios_param = dc395x_bios_param, 4802 .slave_alloc = dc395x_slave_alloc, 4803 .slave_destroy = dc395x_slave_destroy, 4804 .can_queue = DC395x_MAX_CAN_QUEUE, 4805 .this_id = 7, 4806 .sg_tablesize = DC395x_MAX_SG_TABLESIZE, 4807 .cmd_per_lun = DC395x_MAX_CMD_PER_LUN, 4808 .eh_abort_handler = dc395x_eh_abort, 4809 .eh_bus_reset_handler = dc395x_eh_bus_reset, 4810 .unchecked_isa_dma = 0, 4811 .use_clustering = DISABLE_CLUSTERING, 4812 }; 4813 4814 4815 /** 4816 * banner_display - Display banner on first instance of driver 4817 * initialized. 4818 **/ 4819 static void banner_display(void) 4820 { 4821 static int banner_done = 0; 4822 if (!banner_done) 4823 { 4824 dprintkl(KERN_INFO, "%s %s\n", DC395X_BANNER, DC395X_VERSION); 4825 banner_done = 1; 4826 } 4827 } 4828 4829 4830 /** 4831 * dc395x_init_one - Initialise a single instance of the adapter. 4832 * 4833 * The PCI layer will call this once for each instance of the adapter 4834 * that it finds in the system. The pci_dev strcuture indicates which 4835 * instance we are being called from. 4836 * 4837 * @dev: The PCI device to intialize. 4838 * @id: Looks like a pointer to the entry in our pci device table 4839 * that was actually matched by the PCI subsystem. 4840 * 4841 * Returns 0 on success, or an error code (-ve) on failure. 4842 **/ 4843 static int __devinit dc395x_init_one(struct pci_dev *dev, 4844 const struct pci_device_id *id) 4845 { 4846 struct Scsi_Host *scsi_host = NULL; 4847 struct AdapterCtlBlk *acb = NULL; 4848 unsigned long io_port_base; 4849 unsigned int io_port_len; 4850 unsigned int irq; 4851 4852 dprintkdbg(DBG_0, "Init one instance (%s)\n", pci_name(dev)); 4853 banner_display(); 4854 4855 if (pci_enable_device(dev)) 4856 { 4857 dprintkl(KERN_INFO, "PCI Enable device failed.\n"); 4858 return -ENODEV; 4859 } 4860 io_port_base = pci_resource_start(dev, 0) & PCI_BASE_ADDRESS_IO_MASK; 4861 io_port_len = pci_resource_len(dev, 0); 4862 irq = dev->irq; 4863 dprintkdbg(DBG_0, "IO_PORT=0x%04lx, IRQ=0x%x\n", io_port_base, dev->irq); 4864 4865 /* allocate scsi host information (includes out adapter) */ 4866 scsi_host = scsi_host_alloc(&dc395x_driver_template, 4867 sizeof(struct AdapterCtlBlk)); 4868 if (!scsi_host) { 4869 dprintkl(KERN_INFO, "scsi_host_alloc failed\n"); 4870 goto fail; 4871 } 4872 acb = (struct AdapterCtlBlk*)scsi_host->hostdata; 4873 acb->scsi_host = scsi_host; 4874 acb->dev = dev; 4875 4876 /* initialise the adapter and everything we need */ 4877 if (adapter_init(acb, io_port_base, io_port_len, irq)) { 4878 dprintkl(KERN_INFO, "adapter init failed\n"); 4879 goto fail; 4880 } 4881 4882 pci_set_master(dev); 4883 4884 /* get the scsi mid level to scan for new devices on the bus */ 4885 if (scsi_add_host(scsi_host, &dev->dev)) { 4886 dprintkl(KERN_ERR, "scsi_add_host failed\n"); 4887 goto fail; 4888 } 4889 pci_set_drvdata(dev, scsi_host); 4890 scsi_scan_host(scsi_host); 4891 4892 return 0; 4893 4894 fail: 4895 if (acb != NULL) 4896 adapter_uninit(acb); 4897 if (scsi_host != NULL) 4898 scsi_host_put(scsi_host); 4899 pci_disable_device(dev); 4900 return -ENODEV; 4901 } 4902 4903 4904 /** 4905 * dc395x_remove_one - Called to remove a single instance of the 4906 * adapter. 4907 * 4908 * @dev: The PCI device to intialize. 4909 **/ 4910 static void __devexit dc395x_remove_one(struct pci_dev *dev) 4911 { 4912 struct Scsi_Host *scsi_host = pci_get_drvdata(dev); 4913 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)(scsi_host->hostdata); 4914 4915 dprintkdbg(DBG_0, "dc395x_remove_one: acb=%p\n", acb); 4916 4917 scsi_remove_host(scsi_host); 4918 adapter_uninit(acb); 4919 pci_disable_device(dev); 4920 scsi_host_put(scsi_host); 4921 pci_set_drvdata(dev, NULL); 4922 } 4923 4924 4925 static struct pci_device_id dc395x_pci_table[] = { 4926 { 4927 .vendor = PCI_VENDOR_ID_TEKRAM, 4928 .device = PCI_DEVICE_ID_TEKRAM_TRMS1040, 4929 .subvendor = PCI_ANY_ID, 4930 .subdevice = PCI_ANY_ID, 4931 }, 4932 {} /* Terminating entry */ 4933 }; 4934 MODULE_DEVICE_TABLE(pci, dc395x_pci_table); 4935 4936 4937 static struct pci_driver dc395x_driver = { 4938 .name = DC395X_NAME, 4939 .id_table = dc395x_pci_table, 4940 .probe = dc395x_init_one, 4941 .remove = __devexit_p(dc395x_remove_one), 4942 }; 4943 4944 4945 /** 4946 * dc395x_module_init - Module initialization function 4947 * 4948 * Used by both module and built-in driver to initialise this driver. 4949 **/ 4950 static int __init dc395x_module_init(void) 4951 { 4952 return pci_module_init(&dc395x_driver); 4953 } 4954 4955 4956 /** 4957 * dc395x_module_exit - Module cleanup function. 4958 **/ 4959 static void __exit dc395x_module_exit(void) 4960 { 4961 pci_unregister_driver(&dc395x_driver); 4962 } 4963 4964 4965 module_init(dc395x_module_init); 4966 module_exit(dc395x_module_exit); 4967 4968 MODULE_AUTHOR("C.L. Huang / Erich Chen / Kurt Garloff"); 4969 MODULE_DESCRIPTION("SCSI host adapter driver for Tekram TRM-S1040 based adapters: Tekram DC395 and DC315 series"); 4970 MODULE_LICENSE("GPL"); 4971