1 // SPDX-License-Identifier: GPL-2.0-only 2 // 3 // Copyright 2014 Embest Technology Co. Ltd. Inc. 4 // bd71815-regulator.c ROHM BD71815 regulator driver 5 // 6 // Author: Tony Luo <luofc@embedinfo.com> 7 // 8 // Partially rewritten at 2021 by 9 // Matti Vaittinen <matti.vaitinen@fi.rohmeurope.com> 10 11 #include <linux/kernel.h> 12 #include <linux/module.h> 13 #include <linux/init.h> 14 #include <linux/err.h> 15 #include <linux/platform_device.h> 16 #include <linux/of.h> 17 #include <linux/gpio/consumer.h> 18 #include <linux/regulator/driver.h> 19 #include <linux/delay.h> 20 #include <linux/slab.h> 21 #include <linux/mfd/rohm-generic.h> 22 #include <linux/mfd/rohm-bd71815.h> 23 #include <linux/regulator/of_regulator.h> 24 25 struct bd71815_regulator { 26 struct regulator_desc desc; 27 const struct rohm_dvs_config *dvs; 28 }; 29 30 static const int bd7181x_wled_currents[] = { 31 10, 20, 30, 50, 70, 100, 200, 300, 500, 700, 1000, 2000, 3000, 4000, 32 5000, 6000, 7000, 8000, 9000, 10000, 11000, 12000, 13000, 14000, 15000, 33 16000, 17000, 18000, 19000, 20000, 21000, 22000, 23000, 24000, 25000, 34 }; 35 36 static const struct rohm_dvs_config buck1_dvs = { 37 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS | 38 ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR, 39 .run_reg = BD71815_REG_BUCK1_VOLT_H, 40 .run_mask = BD71815_VOLT_MASK, 41 .run_on_mask = BD71815_BUCK_RUN_ON, 42 .snvs_on_mask = BD71815_BUCK_SNVS_ON, 43 .suspend_reg = BD71815_REG_BUCK1_VOLT_L, 44 .suspend_mask = BD71815_VOLT_MASK, 45 .suspend_on_mask = BD71815_BUCK_SUSP_ON, 46 .lpsr_reg = BD71815_REG_BUCK1_VOLT_L, 47 .lpsr_mask = BD71815_VOLT_MASK, 48 .lpsr_on_mask = BD71815_BUCK_LPSR_ON, 49 }; 50 51 static const struct rohm_dvs_config buck2_dvs = { 52 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS | 53 ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR, 54 .run_reg = BD71815_REG_BUCK2_VOLT_H, 55 .run_mask = BD71815_VOLT_MASK, 56 .run_on_mask = BD71815_BUCK_RUN_ON, 57 .snvs_on_mask = BD71815_BUCK_SNVS_ON, 58 .suspend_reg = BD71815_REG_BUCK2_VOLT_L, 59 .suspend_mask = BD71815_VOLT_MASK, 60 .suspend_on_mask = BD71815_BUCK_SUSP_ON, 61 .lpsr_reg = BD71815_REG_BUCK2_VOLT_L, 62 .lpsr_mask = BD71815_VOLT_MASK, 63 .lpsr_on_mask = BD71815_BUCK_LPSR_ON, 64 }; 65 66 static const struct rohm_dvs_config buck3_dvs = { 67 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS | 68 ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR, 69 .run_reg = BD71815_REG_BUCK3_VOLT, 70 .run_mask = BD71815_VOLT_MASK, 71 .run_on_mask = BD71815_BUCK_RUN_ON, 72 .snvs_on_mask = BD71815_BUCK_SNVS_ON, 73 .suspend_on_mask = BD71815_BUCK_SUSP_ON, 74 .lpsr_on_mask = BD71815_BUCK_LPSR_ON, 75 }; 76 77 static const struct rohm_dvs_config buck4_dvs = { 78 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS | 79 ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR, 80 .run_reg = BD71815_REG_BUCK4_VOLT, 81 .run_mask = BD71815_VOLT_MASK, 82 .run_on_mask = BD71815_BUCK_RUN_ON, 83 .snvs_on_mask = BD71815_BUCK_SNVS_ON, 84 .suspend_on_mask = BD71815_BUCK_SUSP_ON, 85 .lpsr_on_mask = BD71815_BUCK_LPSR_ON, 86 }; 87 88 static const struct rohm_dvs_config ldo1_dvs = { 89 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS | 90 ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR, 91 .run_reg = BD71815_REG_LDO_MODE1, 92 .run_mask = BD71815_VOLT_MASK, 93 .run_on_mask = LDO1_RUN_ON, 94 .snvs_on_mask = LDO1_SNVS_ON, 95 .suspend_on_mask = LDO1_SUSP_ON, 96 .lpsr_on_mask = LDO1_LPSR_ON, 97 }; 98 99 static const struct rohm_dvs_config ldo2_dvs = { 100 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS | 101 ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR, 102 .run_reg = BD71815_REG_LDO_MODE2, 103 .run_mask = BD71815_VOLT_MASK, 104 .run_on_mask = LDO2_RUN_ON, 105 .snvs_on_mask = LDO2_SNVS_ON, 106 .suspend_on_mask = LDO2_SUSP_ON, 107 .lpsr_on_mask = LDO2_LPSR_ON, 108 }; 109 110 static const struct rohm_dvs_config ldo3_dvs = { 111 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS | 112 ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR, 113 .run_reg = BD71815_REG_LDO_MODE2, 114 .run_mask = BD71815_VOLT_MASK, 115 .run_on_mask = LDO3_RUN_ON, 116 .snvs_on_mask = LDO3_SNVS_ON, 117 .suspend_on_mask = LDO3_SUSP_ON, 118 .lpsr_on_mask = LDO3_LPSR_ON, 119 }; 120 121 static const struct rohm_dvs_config ldo4_dvs = { 122 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS | 123 ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR, 124 .run_reg = BD71815_REG_LDO_MODE3, 125 .run_mask = BD71815_VOLT_MASK, 126 .run_on_mask = LDO4_RUN_ON, 127 .snvs_on_mask = LDO4_SNVS_ON, 128 .suspend_on_mask = LDO4_SUSP_ON, 129 .lpsr_on_mask = LDO4_LPSR_ON, 130 }; 131 132 static const struct rohm_dvs_config ldo5_dvs = { 133 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS | 134 ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR, 135 .run_reg = BD71815_REG_LDO_MODE3, 136 .run_mask = BD71815_VOLT_MASK, 137 .run_on_mask = LDO5_RUN_ON, 138 .snvs_on_mask = LDO5_SNVS_ON, 139 .suspend_on_mask = LDO5_SUSP_ON, 140 .lpsr_on_mask = LDO5_LPSR_ON, 141 }; 142 143 static const struct rohm_dvs_config dvref_dvs = { 144 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS | 145 ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR, 146 .run_on_mask = DVREF_RUN_ON, 147 .snvs_on_mask = DVREF_SNVS_ON, 148 .suspend_on_mask = DVREF_SUSP_ON, 149 .lpsr_on_mask = DVREF_LPSR_ON, 150 }; 151 152 static const struct rohm_dvs_config ldolpsr_dvs = { 153 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS | 154 ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR, 155 .run_on_mask = DVREF_RUN_ON, 156 .snvs_on_mask = DVREF_SNVS_ON, 157 .suspend_on_mask = DVREF_SUSP_ON, 158 .lpsr_on_mask = DVREF_LPSR_ON, 159 }; 160 161 static const struct rohm_dvs_config buck5_dvs = { 162 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_SNVS | 163 ROHM_DVS_LEVEL_SUSPEND | ROHM_DVS_LEVEL_LPSR, 164 .run_reg = BD71815_REG_BUCK5_VOLT, 165 .run_mask = BD71815_VOLT_MASK, 166 .run_on_mask = BD71815_BUCK_RUN_ON, 167 .snvs_on_mask = BD71815_BUCK_SNVS_ON, 168 .suspend_on_mask = BD71815_BUCK_SUSP_ON, 169 .lpsr_on_mask = BD71815_BUCK_LPSR_ON, 170 }; 171 172 static int set_hw_dvs_levels(struct device_node *np, 173 const struct regulator_desc *desc, 174 struct regulator_config *cfg) 175 { 176 struct bd71815_regulator *data; 177 178 data = container_of(desc, struct bd71815_regulator, desc); 179 return rohm_regulator_set_dvs_levels(data->dvs, np, desc, cfg->regmap); 180 } 181 182 /* 183 * Bucks 1 and 2 have two voltage selection registers where selected 184 * voltage can be set. Which of the registers is used can be either controlled 185 * by a control bit in register - or by HW state. If HW state specific voltages 186 * are given - then we assume HW state based control should be used. 187 * 188 * If volatge value is updated to currently selected register - then output 189 * voltage is immediately changed no matter what is set as ramp rate. Thus we 190 * default changing voltage by writing new value to inactive register and 191 * then updating the 'register selection' bit. This naturally only works when 192 * HW state machine is not used to select the voltage. 193 */ 194 static int buck12_set_hw_dvs_levels(struct device_node *np, 195 const struct regulator_desc *desc, 196 struct regulator_config *cfg) 197 { 198 struct bd71815_regulator *data; 199 int ret = 0, val; 200 201 data = container_of(desc, struct bd71815_regulator, desc); 202 203 if (of_property_present(np, "rohm,dvs-run-voltage") || 204 of_property_present(np, "rohm,dvs-suspend-voltage") || 205 of_property_present(np, "rohm,dvs-lpsr-voltage") || 206 of_property_present(np, "rohm,dvs-snvs-voltage")) { 207 ret = regmap_read(cfg->regmap, desc->vsel_reg, &val); 208 if (ret) 209 return ret; 210 211 if (!(BD71815_BUCK_STBY_DVS & val) && 212 !(BD71815_BUCK_DVSSEL & val)) { 213 int val2; 214 215 /* 216 * We are currently using voltage from _L. 217 * We'd better copy it to _H and switch to it to 218 * avoid shutting us down if LPSR or SUSPEND is set to 219 * disabled. _L value is at reg _H + 1 220 */ 221 ret = regmap_read(cfg->regmap, desc->vsel_reg + 1, 222 &val2); 223 if (ret) 224 return ret; 225 226 ret = regmap_update_bits(cfg->regmap, desc->vsel_reg, 227 BD71815_VOLT_MASK | 228 BD71815_BUCK_DVSSEL, 229 val2 | BD71815_BUCK_DVSSEL); 230 if (ret) 231 return ret; 232 } 233 ret = rohm_regulator_set_dvs_levels(data->dvs, np, desc, 234 cfg->regmap); 235 if (ret) 236 return ret; 237 /* 238 * DVS levels were given => use HW-state machine for voltage 239 * controls. NOTE: AFAIK, This means that if voltage is changed 240 * by SW the ramp-rate is not respected. Should we disable 241 * SW voltage control when the HW state machine is used? 242 */ 243 ret = regmap_update_bits(cfg->regmap, desc->vsel_reg, 244 BD71815_BUCK_STBY_DVS, 245 BD71815_BUCK_STBY_DVS); 246 } 247 248 return ret; 249 } 250 251 /* 252 * BUCK1/2 253 * BUCK1RAMPRATE[1:0] BUCK1 DVS ramp rate setting 254 * 00: 10.00mV/usec 10mV 1uS 255 * 01: 5.00mV/usec 10mV 2uS 256 * 10: 2.50mV/usec 10mV 4uS 257 * 11: 1.25mV/usec 10mV 8uS 258 */ 259 static const unsigned int bd7181x_ramp_table[] = { 10000, 5000, 2500, 1250 }; 260 261 static int bd7181x_led_set_current_limit(struct regulator_dev *rdev, 262 int min_uA, int max_uA) 263 { 264 int ret; 265 int onstatus; 266 267 onstatus = regulator_is_enabled_regmap(rdev); 268 269 ret = regulator_set_current_limit_regmap(rdev, min_uA, max_uA); 270 if (!ret) { 271 int newstatus; 272 273 newstatus = regulator_is_enabled_regmap(rdev); 274 if (onstatus != newstatus) { 275 /* 276 * HW FIX: spurious led status change detected. Toggle 277 * state as a workaround 278 */ 279 if (onstatus) 280 ret = regulator_enable_regmap(rdev); 281 else 282 ret = regulator_disable_regmap(rdev); 283 284 if (ret) 285 dev_err(rdev_get_dev(rdev), 286 "failed to revert the LED state (%d)\n", 287 ret); 288 } 289 } 290 291 return ret; 292 } 293 294 static int bd7181x_buck12_get_voltage_sel(struct regulator_dev *rdev) 295 { 296 int rid = rdev_get_id(rdev); 297 int ret, regh, regl, val; 298 299 regh = BD71815_REG_BUCK1_VOLT_H + rid * 0x2; 300 regl = BD71815_REG_BUCK1_VOLT_L + rid * 0x2; 301 302 ret = regmap_read(rdev->regmap, regh, &val); 303 if (ret) 304 return ret; 305 306 /* 307 * If we use HW state machine based voltage reg selection - then we 308 * return BD71815_REG_BUCK1_VOLT_H which is used at RUN. 309 * Else we do return the BD71815_REG_BUCK1_VOLT_H or 310 * BD71815_REG_BUCK1_VOLT_L depending on which is selected to be used 311 * by BD71815_BUCK_DVSSEL bit 312 */ 313 if ((!(val & BD71815_BUCK_STBY_DVS)) && (!(val & BD71815_BUCK_DVSSEL))) 314 ret = regmap_read(rdev->regmap, regl, &val); 315 316 if (ret) 317 return ret; 318 319 return val & BD71815_VOLT_MASK; 320 } 321 322 /* 323 * For Buck 1/2. 324 */ 325 static int bd7181x_buck12_set_voltage_sel(struct regulator_dev *rdev, 326 unsigned int sel) 327 { 328 int rid = rdev_get_id(rdev); 329 int ret, val, reg, regh, regl; 330 331 regh = BD71815_REG_BUCK1_VOLT_H + rid*0x2; 332 regl = BD71815_REG_BUCK1_VOLT_L + rid*0x2; 333 334 ret = regmap_read(rdev->regmap, regh, &val); 335 if (ret) 336 return ret; 337 338 /* 339 * If bucks 1 & 2 are controlled by state machine - then the RUN state 340 * voltage is set to BD71815_REG_BUCK1_VOLT_H. Changing SUSPEND/LPSR 341 * voltages at runtime is not supported by this driver. 342 */ 343 if (((val & BD71815_BUCK_STBY_DVS))) { 344 return regmap_update_bits(rdev->regmap, regh, BD71815_VOLT_MASK, 345 sel); 346 } 347 /* Update new voltage to the register which is not selected now */ 348 if (val & BD71815_BUCK_DVSSEL) 349 reg = regl; 350 else 351 reg = regh; 352 353 ret = regmap_update_bits(rdev->regmap, reg, BD71815_VOLT_MASK, sel); 354 if (ret) 355 return ret; 356 357 /* Select the other DVS register to be used */ 358 return regmap_update_bits(rdev->regmap, regh, BD71815_BUCK_DVSSEL, 359 ~val); 360 } 361 362 static const struct regulator_ops bd7181x_ldo_regulator_ops = { 363 .enable = regulator_enable_regmap, 364 .disable = regulator_disable_regmap, 365 .is_enabled = regulator_is_enabled_regmap, 366 .list_voltage = regulator_list_voltage_linear, 367 .set_voltage_sel = regulator_set_voltage_sel_regmap, 368 .get_voltage_sel = regulator_get_voltage_sel_regmap, 369 }; 370 371 static const struct regulator_ops bd7181x_fixed_regulator_ops = { 372 .enable = regulator_enable_regmap, 373 .disable = regulator_disable_regmap, 374 .is_enabled = regulator_is_enabled_regmap, 375 .list_voltage = regulator_list_voltage_linear, 376 }; 377 378 static const struct regulator_ops bd7181x_buck_regulator_ops = { 379 .enable = regulator_enable_regmap, 380 .disable = regulator_disable_regmap, 381 .is_enabled = regulator_is_enabled_regmap, 382 .list_voltage = regulator_list_voltage_linear, 383 .set_voltage_sel = regulator_set_voltage_sel_regmap, 384 .get_voltage_sel = regulator_get_voltage_sel_regmap, 385 .set_voltage_time_sel = regulator_set_voltage_time_sel, 386 }; 387 388 static const struct regulator_ops bd7181x_buck12_regulator_ops = { 389 .enable = regulator_enable_regmap, 390 .disable = regulator_disable_regmap, 391 .is_enabled = regulator_is_enabled_regmap, 392 .list_voltage = regulator_list_voltage_linear, 393 .set_voltage_sel = bd7181x_buck12_set_voltage_sel, 394 .get_voltage_sel = bd7181x_buck12_get_voltage_sel, 395 .set_voltage_time_sel = regulator_set_voltage_time_sel, 396 .set_ramp_delay = regulator_set_ramp_delay_regmap, 397 }; 398 399 static const struct regulator_ops bd7181x_led_regulator_ops = { 400 .enable = regulator_enable_regmap, 401 .disable = regulator_disable_regmap, 402 .is_enabled = regulator_is_enabled_regmap, 403 .set_current_limit = bd7181x_led_set_current_limit, 404 .get_current_limit = regulator_get_current_limit_regmap, 405 }; 406 407 #define BD71815_FIXED_REG(_name, _id, ereg, emsk, voltage, _dvs) \ 408 [(_id)] = { \ 409 .desc = { \ 410 .name = #_name, \ 411 .of_match = of_match_ptr(#_name), \ 412 .regulators_node = of_match_ptr("regulators"), \ 413 .n_voltages = 1, \ 414 .ops = &bd7181x_fixed_regulator_ops, \ 415 .type = REGULATOR_VOLTAGE, \ 416 .id = (_id), \ 417 .owner = THIS_MODULE, \ 418 .min_uV = (voltage), \ 419 .enable_reg = (ereg), \ 420 .enable_mask = (emsk), \ 421 .of_parse_cb = set_hw_dvs_levels, \ 422 }, \ 423 .dvs = (_dvs), \ 424 } 425 426 #define BD71815_BUCK_REG(_name, _id, vsel, ereg, min, max, step, _dvs) \ 427 [(_id)] = { \ 428 .desc = { \ 429 .name = #_name, \ 430 .of_match = of_match_ptr(#_name), \ 431 .regulators_node = of_match_ptr("regulators"), \ 432 .n_voltages = ((max) - (min)) / (step) + 1, \ 433 .ops = &bd7181x_buck_regulator_ops, \ 434 .type = REGULATOR_VOLTAGE, \ 435 .id = (_id), \ 436 .owner = THIS_MODULE, \ 437 .min_uV = (min), \ 438 .uV_step = (step), \ 439 .vsel_reg = (vsel), \ 440 .vsel_mask = BD71815_VOLT_MASK, \ 441 .enable_reg = (ereg), \ 442 .enable_mask = BD71815_BUCK_RUN_ON, \ 443 .of_parse_cb = set_hw_dvs_levels, \ 444 }, \ 445 .dvs = (_dvs), \ 446 } 447 448 #define BD71815_BUCK12_REG(_name, _id, vsel, ereg, min, max, step, \ 449 _dvs) \ 450 [(_id)] = { \ 451 .desc = { \ 452 .name = #_name, \ 453 .of_match = of_match_ptr(#_name), \ 454 .regulators_node = of_match_ptr("regulators"), \ 455 .n_voltages = ((max) - (min)) / (step) + 1, \ 456 .ops = &bd7181x_buck12_regulator_ops, \ 457 .type = REGULATOR_VOLTAGE, \ 458 .id = (_id), \ 459 .owner = THIS_MODULE, \ 460 .min_uV = (min), \ 461 .uV_step = (step), \ 462 .vsel_reg = (vsel), \ 463 .vsel_mask = BD71815_VOLT_MASK, \ 464 .enable_reg = (ereg), \ 465 .enable_mask = BD71815_BUCK_RUN_ON, \ 466 .ramp_reg = (ereg), \ 467 .ramp_mask = BD71815_BUCK_RAMPRATE_MASK, \ 468 .ramp_delay_table = bd7181x_ramp_table, \ 469 .n_ramp_values = ARRAY_SIZE(bd7181x_ramp_table),\ 470 .of_parse_cb = buck12_set_hw_dvs_levels, \ 471 }, \ 472 .dvs = (_dvs), \ 473 } 474 475 #define BD71815_LED_REG(_name, _id, csel, mask, ereg, emsk, currents) \ 476 [(_id)] = { \ 477 .desc = { \ 478 .name = #_name, \ 479 .of_match = of_match_ptr(#_name), \ 480 .regulators_node = of_match_ptr("regulators"), \ 481 .n_current_limits = ARRAY_SIZE(currents), \ 482 .ops = &bd7181x_led_regulator_ops, \ 483 .type = REGULATOR_CURRENT, \ 484 .id = (_id), \ 485 .owner = THIS_MODULE, \ 486 .curr_table = currents, \ 487 .csel_reg = (csel), \ 488 .csel_mask = (mask), \ 489 .enable_reg = (ereg), \ 490 .enable_mask = (emsk), \ 491 }, \ 492 } 493 494 #define BD71815_LDO_REG(_name, _id, vsel, ereg, emsk, min, max, step, \ 495 _dvs) \ 496 [(_id)] = { \ 497 .desc = { \ 498 .name = #_name, \ 499 .of_match = of_match_ptr(#_name), \ 500 .regulators_node = of_match_ptr("regulators"), \ 501 .n_voltages = ((max) - (min)) / (step) + 1, \ 502 .ops = &bd7181x_ldo_regulator_ops, \ 503 .type = REGULATOR_VOLTAGE, \ 504 .id = (_id), \ 505 .owner = THIS_MODULE, \ 506 .min_uV = (min), \ 507 .uV_step = (step), \ 508 .vsel_reg = (vsel), \ 509 .vsel_mask = BD71815_VOLT_MASK, \ 510 .enable_reg = (ereg), \ 511 .enable_mask = (emsk), \ 512 .of_parse_cb = set_hw_dvs_levels, \ 513 }, \ 514 .dvs = (_dvs), \ 515 } 516 517 static const struct bd71815_regulator bd71815_regulators[] = { 518 BD71815_BUCK12_REG(buck1, BD71815_BUCK1, BD71815_REG_BUCK1_VOLT_H, 519 BD71815_REG_BUCK1_MODE, 800000, 2000000, 25000, 520 &buck1_dvs), 521 BD71815_BUCK12_REG(buck2, BD71815_BUCK2, BD71815_REG_BUCK2_VOLT_H, 522 BD71815_REG_BUCK2_MODE, 800000, 2000000, 25000, 523 &buck2_dvs), 524 BD71815_BUCK_REG(buck3, BD71815_BUCK3, BD71815_REG_BUCK3_VOLT, 525 BD71815_REG_BUCK3_MODE, 1200000, 2700000, 50000, 526 &buck3_dvs), 527 BD71815_BUCK_REG(buck4, BD71815_BUCK4, BD71815_REG_BUCK4_VOLT, 528 BD71815_REG_BUCK4_MODE, 1100000, 1850000, 25000, 529 &buck4_dvs), 530 BD71815_BUCK_REG(buck5, BD71815_BUCK5, BD71815_REG_BUCK5_VOLT, 531 BD71815_REG_BUCK5_MODE, 1800000, 3300000, 50000, 532 &buck5_dvs), 533 BD71815_LDO_REG(ldo1, BD71815_LDO1, BD71815_REG_LDO1_VOLT, 534 BD71815_REG_LDO_MODE1, LDO1_RUN_ON, 800000, 3300000, 535 50000, &ldo1_dvs), 536 BD71815_LDO_REG(ldo2, BD71815_LDO2, BD71815_REG_LDO2_VOLT, 537 BD71815_REG_LDO_MODE2, LDO2_RUN_ON, 800000, 3300000, 538 50000, &ldo2_dvs), 539 /* 540 * Let's default LDO3 to be enabled by SW. We can override ops if DT 541 * says LDO3 should be enabled by HW when DCIN is connected. 542 */ 543 BD71815_LDO_REG(ldo3, BD71815_LDO3, BD71815_REG_LDO3_VOLT, 544 BD71815_REG_LDO_MODE2, LDO3_RUN_ON, 800000, 3300000, 545 50000, &ldo3_dvs), 546 BD71815_LDO_REG(ldo4, BD71815_LDO4, BD71815_REG_LDO4_VOLT, 547 BD71815_REG_LDO_MODE3, LDO4_RUN_ON, 800000, 3300000, 548 50000, &ldo4_dvs), 549 BD71815_LDO_REG(ldo5, BD71815_LDO5, BD71815_REG_LDO5_VOLT_H, 550 BD71815_REG_LDO_MODE3, LDO5_RUN_ON, 800000, 3300000, 551 50000, &ldo5_dvs), 552 BD71815_FIXED_REG(ldodvref, BD71815_LDODVREF, BD71815_REG_LDO_MODE4, 553 DVREF_RUN_ON, 3000000, &dvref_dvs), 554 BD71815_FIXED_REG(ldolpsr, BD71815_LDOLPSR, BD71815_REG_LDO_MODE4, 555 LDO_LPSR_RUN_ON, 1800000, &ldolpsr_dvs), 556 BD71815_LED_REG(wled, BD71815_WLED, BD71815_REG_LED_DIMM, LED_DIMM_MASK, 557 BD71815_REG_LED_CTRL, LED_RUN_ON, 558 bd7181x_wled_currents), 559 }; 560 561 static int bd7181x_probe(struct platform_device *pdev) 562 { 563 struct regulator_config config = {}; 564 int i, ret; 565 struct gpio_desc *ldo4_en; 566 struct regmap *regmap; 567 568 regmap = dev_get_regmap(pdev->dev.parent, NULL); 569 if (!regmap) { 570 dev_err(&pdev->dev, "No parent regmap\n"); 571 return -ENODEV; 572 } 573 574 ldo4_en = devm_fwnode_gpiod_get(&pdev->dev, 575 dev_fwnode(pdev->dev.parent), 576 "rohm,vsel", GPIOD_ASIS, "ldo4-en"); 577 if (IS_ERR(ldo4_en)) { 578 ret = PTR_ERR(ldo4_en); 579 if (ret != -ENOENT) 580 return ret; 581 ldo4_en = NULL; 582 } 583 584 /* Disable to go to ship-mode */ 585 ret = regmap_update_bits(regmap, BD71815_REG_PWRCTRL, RESTARTEN, 0); 586 if (ret) 587 return ret; 588 589 config.dev = pdev->dev.parent; 590 config.regmap = regmap; 591 592 for (i = 0; i < BD71815_REGULATOR_CNT; i++) { 593 const struct regulator_desc *desc; 594 struct regulator_dev *rdev; 595 596 desc = &bd71815_regulators[i].desc; 597 598 if (i == BD71815_LDO4) 599 config.ena_gpiod = ldo4_en; 600 else 601 config.ena_gpiod = NULL; 602 603 rdev = devm_regulator_register(&pdev->dev, desc, &config); 604 if (IS_ERR(rdev)) 605 return dev_err_probe(&pdev->dev, PTR_ERR(rdev), 606 "failed to register %s regulator\n", 607 desc->name); 608 } 609 return 0; 610 } 611 612 static const struct platform_device_id bd7181x_pmic_id[] = { 613 { "bd71815-pmic", ROHM_CHIP_TYPE_BD71815 }, 614 { }, 615 }; 616 MODULE_DEVICE_TABLE(platform, bd7181x_pmic_id); 617 618 static struct platform_driver bd7181x_regulator = { 619 .driver = { 620 .name = "bd7181x-pmic", 621 .probe_type = PROBE_PREFER_ASYNCHRONOUS, 622 }, 623 .probe = bd7181x_probe, 624 .id_table = bd7181x_pmic_id, 625 }; 626 module_platform_driver(bd7181x_regulator); 627 628 MODULE_AUTHOR("Tony Luo <luofc@embedinfo.com>"); 629 MODULE_DESCRIPTION("BD71815 voltage regulator driver"); 630 MODULE_LICENSE("GPL v2"); 631 MODULE_ALIAS("platform:bd7181x-pmic"); 632