1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * PWM device driver for ST SoCs 4 * 5 * Copyright (C) 2013-2016 STMicroelectronics (R&D) Limited 6 * 7 * Author: Ajit Pal Singh <ajitpal.singh@st.com> 8 * Lee Jones <lee.jones@linaro.org> 9 */ 10 11 #include <linux/clk.h> 12 #include <linux/interrupt.h> 13 #include <linux/math64.h> 14 #include <linux/mfd/syscon.h> 15 #include <linux/module.h> 16 #include <linux/of.h> 17 #include <linux/platform_device.h> 18 #include <linux/pwm.h> 19 #include <linux/regmap.h> 20 #include <linux/sched.h> 21 #include <linux/slab.h> 22 #include <linux/time.h> 23 #include <linux/wait.h> 24 25 #define PWM_OUT_VAL(x) (0x00 + (4 * (x))) /* Device's Duty Cycle register */ 26 #define PWM_CPT_VAL(x) (0x10 + (4 * (x))) /* Capture value */ 27 #define PWM_CPT_EDGE(x) (0x30 + (4 * (x))) /* Edge to capture on */ 28 29 #define STI_PWM_CTRL 0x50 /* Control/Config register */ 30 #define STI_INT_EN 0x54 /* Interrupt Enable/Disable register */ 31 #define STI_INT_STA 0x58 /* Interrupt Status register */ 32 #define PWM_INT_ACK 0x5c 33 #define PWM_PRESCALE_LOW_MASK 0x0f 34 #define PWM_PRESCALE_HIGH_MASK 0xf0 35 #define PWM_CPT_EDGE_MASK 0x03 36 #define PWM_INT_ACK_MASK 0x1ff 37 38 #define STI_MAX_CPT_DEVS 4 39 #define CPT_DC_MAX 0xff 40 41 /* Regfield IDs */ 42 enum { 43 /* Bits in PWM_CTRL*/ 44 PWMCLK_PRESCALE_LOW, 45 PWMCLK_PRESCALE_HIGH, 46 CPTCLK_PRESCALE, 47 48 PWM_OUT_EN, 49 PWM_CPT_EN, 50 51 PWM_CPT_INT_EN, 52 PWM_CPT_INT_STAT, 53 54 /* Keep last */ 55 MAX_REGFIELDS 56 }; 57 58 /* 59 * Each capture input can be programmed to detect rising-edge, falling-edge, 60 * either edge or neither egde. 61 */ 62 enum sti_cpt_edge { 63 CPT_EDGE_DISABLED, 64 CPT_EDGE_RISING, 65 CPT_EDGE_FALLING, 66 CPT_EDGE_BOTH, 67 }; 68 69 struct sti_cpt_ddata { 70 u32 snapshot[3]; 71 unsigned int index; 72 struct mutex lock; 73 wait_queue_head_t wait; 74 }; 75 76 struct sti_pwm_compat_data { 77 const struct reg_field *reg_fields; 78 unsigned int pwm_num_devs; 79 unsigned int cpt_num_devs; 80 unsigned int max_pwm_cnt; 81 unsigned int max_prescale; 82 struct sti_cpt_ddata *ddata; 83 }; 84 85 struct sti_pwm_chip { 86 struct device *dev; 87 struct clk *pwm_clk; 88 struct clk *cpt_clk; 89 struct regmap *regmap; 90 struct sti_pwm_compat_data *cdata; 91 struct regmap_field *prescale_low; 92 struct regmap_field *prescale_high; 93 struct regmap_field *pwm_out_en; 94 struct regmap_field *pwm_cpt_en; 95 struct regmap_field *pwm_cpt_int_en; 96 struct regmap_field *pwm_cpt_int_stat; 97 struct pwm_chip chip; 98 struct pwm_device *cur; 99 unsigned long configured; 100 unsigned int en_count; 101 struct mutex sti_pwm_lock; /* To sync between enable/disable calls */ 102 void __iomem *mmio; 103 }; 104 105 static const struct reg_field sti_pwm_regfields[MAX_REGFIELDS] = { 106 [PWMCLK_PRESCALE_LOW] = REG_FIELD(STI_PWM_CTRL, 0, 3), 107 [PWMCLK_PRESCALE_HIGH] = REG_FIELD(STI_PWM_CTRL, 11, 14), 108 [CPTCLK_PRESCALE] = REG_FIELD(STI_PWM_CTRL, 4, 8), 109 [PWM_OUT_EN] = REG_FIELD(STI_PWM_CTRL, 9, 9), 110 [PWM_CPT_EN] = REG_FIELD(STI_PWM_CTRL, 10, 10), 111 [PWM_CPT_INT_EN] = REG_FIELD(STI_INT_EN, 1, 4), 112 [PWM_CPT_INT_STAT] = REG_FIELD(STI_INT_STA, 1, 4), 113 }; 114 115 static inline struct sti_pwm_chip *to_sti_pwmchip(struct pwm_chip *chip) 116 { 117 return container_of(chip, struct sti_pwm_chip, chip); 118 } 119 120 /* 121 * Calculate the prescaler value corresponding to the period. 122 */ 123 static int sti_pwm_get_prescale(struct sti_pwm_chip *pc, unsigned long period, 124 unsigned int *prescale) 125 { 126 struct sti_pwm_compat_data *cdata = pc->cdata; 127 unsigned long clk_rate; 128 unsigned long value; 129 unsigned int ps; 130 131 clk_rate = clk_get_rate(pc->pwm_clk); 132 if (!clk_rate) { 133 dev_err(pc->dev, "failed to get clock rate\n"); 134 return -EINVAL; 135 } 136 137 /* 138 * prescale = ((period_ns * clk_rate) / (10^9 * (max_pwm_cnt + 1)) - 1 139 */ 140 value = NSEC_PER_SEC / clk_rate; 141 value *= cdata->max_pwm_cnt + 1; 142 143 if (period % value) 144 return -EINVAL; 145 146 ps = period / value - 1; 147 if (ps > cdata->max_prescale) 148 return -EINVAL; 149 150 *prescale = ps; 151 152 return 0; 153 } 154 155 /* 156 * For STiH4xx PWM IP, the PWM period is fixed to 256 local clock cycles. The 157 * only way to change the period (apart from changing the PWM input clock) is 158 * to change the PWM clock prescaler. 159 * 160 * The prescaler is of 8 bits, so 256 prescaler values and hence 256 possible 161 * period values are supported (for a particular clock rate). The requested 162 * period will be applied only if it matches one of these 256 values. 163 */ 164 static int sti_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm, 165 int duty_ns, int period_ns) 166 { 167 struct sti_pwm_chip *pc = to_sti_pwmchip(chip); 168 struct sti_pwm_compat_data *cdata = pc->cdata; 169 unsigned int ncfg, value, prescale = 0; 170 struct pwm_device *cur = pc->cur; 171 struct device *dev = pc->dev; 172 bool period_same = false; 173 int ret; 174 175 ncfg = hweight_long(pc->configured); 176 if (ncfg) 177 period_same = (period_ns == pwm_get_period(cur)); 178 179 /* 180 * Allow configuration changes if one of the following conditions 181 * satisfy. 182 * 1. No devices have been configured. 183 * 2. Only one device has been configured and the new request is for 184 * the same device. 185 * 3. Only one device has been configured and the new request is for 186 * a new device and period of the new device is same as the current 187 * configured period. 188 * 4. More than one devices are configured and period of the new 189 * requestis the same as the current period. 190 */ 191 if (!ncfg || 192 ((ncfg == 1) && (pwm->hwpwm == cur->hwpwm)) || 193 ((ncfg == 1) && (pwm->hwpwm != cur->hwpwm) && period_same) || 194 ((ncfg > 1) && period_same)) { 195 /* Enable clock before writing to PWM registers. */ 196 ret = clk_enable(pc->pwm_clk); 197 if (ret) 198 return ret; 199 200 ret = clk_enable(pc->cpt_clk); 201 if (ret) 202 return ret; 203 204 if (!period_same) { 205 ret = sti_pwm_get_prescale(pc, period_ns, &prescale); 206 if (ret) 207 goto clk_dis; 208 209 value = prescale & PWM_PRESCALE_LOW_MASK; 210 211 ret = regmap_field_write(pc->prescale_low, value); 212 if (ret) 213 goto clk_dis; 214 215 value = (prescale & PWM_PRESCALE_HIGH_MASK) >> 4; 216 217 ret = regmap_field_write(pc->prescale_high, value); 218 if (ret) 219 goto clk_dis; 220 } 221 222 /* 223 * When PWMVal == 0, PWM pulse = 1 local clock cycle. 224 * When PWMVal == max_pwm_count, 225 * PWM pulse = (max_pwm_count + 1) local cycles, 226 * that is continuous pulse: signal never goes low. 227 */ 228 value = cdata->max_pwm_cnt * duty_ns / period_ns; 229 230 ret = regmap_write(pc->regmap, PWM_OUT_VAL(pwm->hwpwm), value); 231 if (ret) 232 goto clk_dis; 233 234 ret = regmap_field_write(pc->pwm_cpt_int_en, 0); 235 236 set_bit(pwm->hwpwm, &pc->configured); 237 pc->cur = pwm; 238 239 dev_dbg(dev, "prescale:%u, period:%i, duty:%i, value:%u\n", 240 prescale, period_ns, duty_ns, value); 241 } else { 242 return -EINVAL; 243 } 244 245 clk_dis: 246 clk_disable(pc->pwm_clk); 247 clk_disable(pc->cpt_clk); 248 return ret; 249 } 250 251 static int sti_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm) 252 { 253 struct sti_pwm_chip *pc = to_sti_pwmchip(chip); 254 struct device *dev = pc->dev; 255 int ret = 0; 256 257 /* 258 * Since we have a common enable for all PWM devices, do not enable if 259 * already enabled. 260 */ 261 mutex_lock(&pc->sti_pwm_lock); 262 263 if (!pc->en_count) { 264 ret = clk_enable(pc->pwm_clk); 265 if (ret) 266 goto out; 267 268 ret = clk_enable(pc->cpt_clk); 269 if (ret) 270 goto out; 271 272 ret = regmap_field_write(pc->pwm_out_en, 1); 273 if (ret) { 274 dev_err(dev, "failed to enable PWM device %u: %d\n", 275 pwm->hwpwm, ret); 276 goto out; 277 } 278 } 279 280 pc->en_count++; 281 282 out: 283 mutex_unlock(&pc->sti_pwm_lock); 284 return ret; 285 } 286 287 static void sti_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm) 288 { 289 struct sti_pwm_chip *pc = to_sti_pwmchip(chip); 290 291 mutex_lock(&pc->sti_pwm_lock); 292 293 if (--pc->en_count) { 294 mutex_unlock(&pc->sti_pwm_lock); 295 return; 296 } 297 298 regmap_field_write(pc->pwm_out_en, 0); 299 300 clk_disable(pc->pwm_clk); 301 clk_disable(pc->cpt_clk); 302 303 mutex_unlock(&pc->sti_pwm_lock); 304 } 305 306 static void sti_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm) 307 { 308 struct sti_pwm_chip *pc = to_sti_pwmchip(chip); 309 310 clear_bit(pwm->hwpwm, &pc->configured); 311 } 312 313 static int sti_pwm_capture(struct pwm_chip *chip, struct pwm_device *pwm, 314 struct pwm_capture *result, unsigned long timeout) 315 { 316 struct sti_pwm_chip *pc = to_sti_pwmchip(chip); 317 struct sti_pwm_compat_data *cdata = pc->cdata; 318 struct sti_cpt_ddata *ddata = &cdata->ddata[pwm->hwpwm]; 319 struct device *dev = pc->dev; 320 unsigned int effective_ticks; 321 unsigned long long high, low; 322 int ret; 323 324 if (pwm->hwpwm >= cdata->cpt_num_devs) { 325 dev_err(dev, "device %u is not valid\n", pwm->hwpwm); 326 return -EINVAL; 327 } 328 329 mutex_lock(&ddata->lock); 330 ddata->index = 0; 331 332 /* Prepare capture measurement */ 333 regmap_write(pc->regmap, PWM_CPT_EDGE(pwm->hwpwm), CPT_EDGE_RISING); 334 regmap_field_write(pc->pwm_cpt_int_en, BIT(pwm->hwpwm)); 335 336 /* Enable capture */ 337 ret = regmap_field_write(pc->pwm_cpt_en, 1); 338 if (ret) { 339 dev_err(dev, "failed to enable PWM capture %u: %d\n", 340 pwm->hwpwm, ret); 341 goto out; 342 } 343 344 ret = wait_event_interruptible_timeout(ddata->wait, ddata->index > 1, 345 msecs_to_jiffies(timeout)); 346 347 regmap_write(pc->regmap, PWM_CPT_EDGE(pwm->hwpwm), CPT_EDGE_DISABLED); 348 349 if (ret == -ERESTARTSYS) 350 goto out; 351 352 switch (ddata->index) { 353 case 0: 354 case 1: 355 /* 356 * Getting here could mean: 357 * - input signal is constant of less than 1 Hz 358 * - there is no input signal at all 359 * 360 * In such case the frequency is rounded down to 0 361 */ 362 result->period = 0; 363 result->duty_cycle = 0; 364 365 break; 366 367 case 2: 368 /* We have everying we need */ 369 high = ddata->snapshot[1] - ddata->snapshot[0]; 370 low = ddata->snapshot[2] - ddata->snapshot[1]; 371 372 effective_ticks = clk_get_rate(pc->cpt_clk); 373 374 result->period = (high + low) * NSEC_PER_SEC; 375 result->period /= effective_ticks; 376 377 result->duty_cycle = high * NSEC_PER_SEC; 378 result->duty_cycle /= effective_ticks; 379 380 break; 381 382 default: 383 dev_err(dev, "internal error\n"); 384 break; 385 } 386 387 out: 388 /* Disable capture */ 389 regmap_field_write(pc->pwm_cpt_en, 0); 390 391 mutex_unlock(&ddata->lock); 392 return ret; 393 } 394 395 static int sti_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, 396 const struct pwm_state *state) 397 { 398 int err; 399 400 if (state->polarity != PWM_POLARITY_NORMAL) 401 return -EINVAL; 402 403 if (!state->enabled) { 404 if (pwm->state.enabled) 405 sti_pwm_disable(chip, pwm); 406 407 return 0; 408 } 409 410 err = sti_pwm_config(chip, pwm, state->duty_cycle, state->period); 411 if (err) 412 return err; 413 414 if (!pwm->state.enabled) 415 err = sti_pwm_enable(chip, pwm); 416 417 return err; 418 } 419 420 static const struct pwm_ops sti_pwm_ops = { 421 .capture = sti_pwm_capture, 422 .apply = sti_pwm_apply, 423 .free = sti_pwm_free, 424 }; 425 426 static irqreturn_t sti_pwm_interrupt(int irq, void *data) 427 { 428 struct sti_pwm_chip *pc = data; 429 struct device *dev = pc->dev; 430 struct sti_cpt_ddata *ddata; 431 int devicenum; 432 unsigned int cpt_int_stat; 433 unsigned int reg; 434 int ret = IRQ_NONE; 435 436 ret = regmap_field_read(pc->pwm_cpt_int_stat, &cpt_int_stat); 437 if (ret) 438 return ret; 439 440 while (cpt_int_stat) { 441 devicenum = ffs(cpt_int_stat) - 1; 442 443 ddata = &pc->cdata->ddata[devicenum]; 444 445 /* 446 * Capture input: 447 * _______ _______ 448 * | | | | 449 * __| |_________________| |________ 450 * ^0 ^1 ^2 451 * 452 * Capture start by the first available rising edge. When a 453 * capture event occurs, capture value (CPT_VALx) is stored, 454 * index incremented, capture edge changed. 455 * 456 * After the capture, if the index > 1, we have collected the 457 * necessary data so we signal the thread waiting for it and 458 * disable the capture by setting capture edge to none 459 */ 460 461 regmap_read(pc->regmap, 462 PWM_CPT_VAL(devicenum), 463 &ddata->snapshot[ddata->index]); 464 465 switch (ddata->index) { 466 case 0: 467 case 1: 468 regmap_read(pc->regmap, PWM_CPT_EDGE(devicenum), ®); 469 reg ^= PWM_CPT_EDGE_MASK; 470 regmap_write(pc->regmap, PWM_CPT_EDGE(devicenum), reg); 471 472 ddata->index++; 473 break; 474 475 case 2: 476 regmap_write(pc->regmap, 477 PWM_CPT_EDGE(devicenum), 478 CPT_EDGE_DISABLED); 479 wake_up(&ddata->wait); 480 break; 481 482 default: 483 dev_err(dev, "Internal error\n"); 484 } 485 486 cpt_int_stat &= ~BIT_MASK(devicenum); 487 488 ret = IRQ_HANDLED; 489 } 490 491 /* Just ACK everything */ 492 regmap_write(pc->regmap, PWM_INT_ACK, PWM_INT_ACK_MASK); 493 494 return ret; 495 } 496 497 static int sti_pwm_probe_dt(struct sti_pwm_chip *pc) 498 { 499 struct device *dev = pc->dev; 500 const struct reg_field *reg_fields; 501 struct device_node *np = dev->of_node; 502 struct sti_pwm_compat_data *cdata = pc->cdata; 503 u32 num_devs; 504 int ret; 505 506 ret = of_property_read_u32(np, "st,pwm-num-chan", &num_devs); 507 if (!ret) 508 cdata->pwm_num_devs = num_devs; 509 510 ret = of_property_read_u32(np, "st,capture-num-chan", &num_devs); 511 if (!ret) 512 cdata->cpt_num_devs = num_devs; 513 514 if (!cdata->pwm_num_devs && !cdata->cpt_num_devs) { 515 dev_err(dev, "No channels configured\n"); 516 return -EINVAL; 517 } 518 519 reg_fields = cdata->reg_fields; 520 521 pc->prescale_low = devm_regmap_field_alloc(dev, pc->regmap, 522 reg_fields[PWMCLK_PRESCALE_LOW]); 523 if (IS_ERR(pc->prescale_low)) 524 return PTR_ERR(pc->prescale_low); 525 526 pc->prescale_high = devm_regmap_field_alloc(dev, pc->regmap, 527 reg_fields[PWMCLK_PRESCALE_HIGH]); 528 if (IS_ERR(pc->prescale_high)) 529 return PTR_ERR(pc->prescale_high); 530 531 pc->pwm_out_en = devm_regmap_field_alloc(dev, pc->regmap, 532 reg_fields[PWM_OUT_EN]); 533 if (IS_ERR(pc->pwm_out_en)) 534 return PTR_ERR(pc->pwm_out_en); 535 536 pc->pwm_cpt_en = devm_regmap_field_alloc(dev, pc->regmap, 537 reg_fields[PWM_CPT_EN]); 538 if (IS_ERR(pc->pwm_cpt_en)) 539 return PTR_ERR(pc->pwm_cpt_en); 540 541 pc->pwm_cpt_int_en = devm_regmap_field_alloc(dev, pc->regmap, 542 reg_fields[PWM_CPT_INT_EN]); 543 if (IS_ERR(pc->pwm_cpt_int_en)) 544 return PTR_ERR(pc->pwm_cpt_int_en); 545 546 pc->pwm_cpt_int_stat = devm_regmap_field_alloc(dev, pc->regmap, 547 reg_fields[PWM_CPT_INT_STAT]); 548 if (PTR_ERR_OR_ZERO(pc->pwm_cpt_int_stat)) 549 return PTR_ERR(pc->pwm_cpt_int_stat); 550 551 return 0; 552 } 553 554 static const struct regmap_config sti_pwm_regmap_config = { 555 .reg_bits = 32, 556 .val_bits = 32, 557 .reg_stride = 4, 558 }; 559 560 static int sti_pwm_probe(struct platform_device *pdev) 561 { 562 struct device *dev = &pdev->dev; 563 struct sti_pwm_compat_data *cdata; 564 struct sti_pwm_chip *pc; 565 unsigned int i; 566 int irq, ret; 567 568 pc = devm_kzalloc(dev, sizeof(*pc), GFP_KERNEL); 569 if (!pc) 570 return -ENOMEM; 571 572 cdata = devm_kzalloc(dev, sizeof(*cdata), GFP_KERNEL); 573 if (!cdata) 574 return -ENOMEM; 575 576 pc->mmio = devm_platform_ioremap_resource(pdev, 0); 577 if (IS_ERR(pc->mmio)) 578 return PTR_ERR(pc->mmio); 579 580 pc->regmap = devm_regmap_init_mmio(dev, pc->mmio, 581 &sti_pwm_regmap_config); 582 if (IS_ERR(pc->regmap)) 583 return PTR_ERR(pc->regmap); 584 585 irq = platform_get_irq(pdev, 0); 586 if (irq < 0) 587 return irq; 588 589 ret = devm_request_irq(&pdev->dev, irq, sti_pwm_interrupt, 0, 590 pdev->name, pc); 591 if (ret < 0) { 592 dev_err(&pdev->dev, "Failed to request IRQ\n"); 593 return ret; 594 } 595 596 /* 597 * Setup PWM data with default values: some values could be replaced 598 * with specific ones provided from Device Tree. 599 */ 600 cdata->reg_fields = sti_pwm_regfields; 601 cdata->max_prescale = 0xff; 602 cdata->max_pwm_cnt = 255; 603 cdata->pwm_num_devs = 0; 604 cdata->cpt_num_devs = 0; 605 606 pc->cdata = cdata; 607 pc->dev = dev; 608 pc->en_count = 0; 609 mutex_init(&pc->sti_pwm_lock); 610 611 ret = sti_pwm_probe_dt(pc); 612 if (ret) 613 return ret; 614 615 if (cdata->pwm_num_devs) { 616 pc->pwm_clk = of_clk_get_by_name(dev->of_node, "pwm"); 617 if (IS_ERR(pc->pwm_clk)) { 618 dev_err(dev, "failed to get PWM clock\n"); 619 return PTR_ERR(pc->pwm_clk); 620 } 621 622 ret = clk_prepare(pc->pwm_clk); 623 if (ret) { 624 dev_err(dev, "failed to prepare clock\n"); 625 return ret; 626 } 627 } 628 629 if (cdata->cpt_num_devs) { 630 pc->cpt_clk = of_clk_get_by_name(dev->of_node, "capture"); 631 if (IS_ERR(pc->cpt_clk)) { 632 dev_err(dev, "failed to get PWM capture clock\n"); 633 return PTR_ERR(pc->cpt_clk); 634 } 635 636 ret = clk_prepare(pc->cpt_clk); 637 if (ret) { 638 dev_err(dev, "failed to prepare clock\n"); 639 return ret; 640 } 641 642 cdata->ddata = devm_kzalloc(dev, cdata->cpt_num_devs * sizeof(*cdata->ddata), GFP_KERNEL); 643 if (!cdata->ddata) 644 return -ENOMEM; 645 } 646 647 pc->chip.dev = dev; 648 pc->chip.ops = &sti_pwm_ops; 649 pc->chip.npwm = pc->cdata->pwm_num_devs; 650 651 for (i = 0; i < cdata->cpt_num_devs; i++) { 652 struct sti_cpt_ddata *ddata = &cdata->ddata[i]; 653 654 init_waitqueue_head(&ddata->wait); 655 mutex_init(&ddata->lock); 656 } 657 658 ret = pwmchip_add(&pc->chip); 659 if (ret < 0) { 660 clk_unprepare(pc->pwm_clk); 661 clk_unprepare(pc->cpt_clk); 662 return ret; 663 } 664 665 platform_set_drvdata(pdev, pc); 666 667 return 0; 668 } 669 670 static void sti_pwm_remove(struct platform_device *pdev) 671 { 672 struct sti_pwm_chip *pc = platform_get_drvdata(pdev); 673 674 pwmchip_remove(&pc->chip); 675 676 clk_unprepare(pc->pwm_clk); 677 clk_unprepare(pc->cpt_clk); 678 } 679 680 static const struct of_device_id sti_pwm_of_match[] = { 681 { .compatible = "st,sti-pwm", }, 682 { /* sentinel */ } 683 }; 684 MODULE_DEVICE_TABLE(of, sti_pwm_of_match); 685 686 static struct platform_driver sti_pwm_driver = { 687 .driver = { 688 .name = "sti-pwm", 689 .of_match_table = sti_pwm_of_match, 690 }, 691 .probe = sti_pwm_probe, 692 .remove_new = sti_pwm_remove, 693 }; 694 module_platform_driver(sti_pwm_driver); 695 696 MODULE_AUTHOR("Ajit Pal Singh <ajitpal.singh@st.com>"); 697 MODULE_DESCRIPTION("STMicroelectronics ST PWM driver"); 698 MODULE_LICENSE("GPL"); 699