1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Amlogic G12A USB3 + PCIE Combo PHY driver 4 * 5 * Copyright (C) 2017 Amlogic, Inc. All rights reserved 6 * Copyright (C) 2019 BayLibre, SAS 7 * Author: Neil Armstrong <narmstrong@baylibre.com> 8 */ 9 10 #include <linux/bitfield.h> 11 #include <linux/bitops.h> 12 #include <linux/clk.h> 13 #include <linux/module.h> 14 #include <linux/of.h> 15 #include <linux/phy/phy.h> 16 #include <linux/regmap.h> 17 #include <linux/reset.h> 18 #include <linux/platform_device.h> 19 #include <dt-bindings/phy/phy.h> 20 21 #define PHY_R0 0x00 22 #define PHY_R0_PCIE_POWER_STATE GENMASK(4, 0) 23 #define PHY_R0_PCIE_USB3_SWITCH GENMASK(6, 5) 24 25 #define PHY_R1 0x04 26 #define PHY_R1_PHY_TX1_TERM_OFFSET GENMASK(4, 0) 27 #define PHY_R1_PHY_TX0_TERM_OFFSET GENMASK(9, 5) 28 #define PHY_R1_PHY_RX1_EQ GENMASK(12, 10) 29 #define PHY_R1_PHY_RX0_EQ GENMASK(15, 13) 30 #define PHY_R1_PHY_LOS_LEVEL GENMASK(20, 16) 31 #define PHY_R1_PHY_LOS_BIAS GENMASK(23, 21) 32 #define PHY_R1_PHY_REF_CLKDIV2 BIT(24) 33 #define PHY_R1_PHY_MPLL_MULTIPLIER GENMASK(31, 25) 34 35 #define PHY_R2 0x08 36 #define PHY_R2_PCS_TX_DEEMPH_GEN2_6DB GENMASK(5, 0) 37 #define PHY_R2_PCS_TX_DEEMPH_GEN2_3P5DB GENMASK(11, 6) 38 #define PHY_R2_PCS_TX_DEEMPH_GEN1 GENMASK(17, 12) 39 #define PHY_R2_PHY_TX_VBOOST_LVL GENMASK(20, 18) 40 41 #define PHY_R4 0x10 42 #define PHY_R4_PHY_CR_WRITE BIT(0) 43 #define PHY_R4_PHY_CR_READ BIT(1) 44 #define PHY_R4_PHY_CR_DATA_IN GENMASK(17, 2) 45 #define PHY_R4_PHY_CR_CAP_DATA BIT(18) 46 #define PHY_R4_PHY_CR_CAP_ADDR BIT(19) 47 48 #define PHY_R5 0x14 49 #define PHY_R5_PHY_CR_DATA_OUT GENMASK(15, 0) 50 #define PHY_R5_PHY_CR_ACK BIT(16) 51 #define PHY_R5_PHY_BS_OUT BIT(17) 52 53 #define PCIE_RESET_DELAY 500 54 55 struct phy_g12a_usb3_pcie_priv { 56 struct regmap *regmap; 57 struct regmap *regmap_cr; 58 struct clk *clk_ref; 59 struct reset_control *reset; 60 struct phy *phy; 61 unsigned int mode; 62 }; 63 64 static const struct regmap_config phy_g12a_usb3_pcie_regmap_conf = { 65 .reg_bits = 8, 66 .val_bits = 32, 67 .reg_stride = 4, 68 .max_register = PHY_R5, 69 }; 70 71 static int phy_g12a_usb3_pcie_cr_bus_addr(struct phy_g12a_usb3_pcie_priv *priv, 72 unsigned int addr) 73 { 74 unsigned int val, reg; 75 int ret; 76 77 reg = FIELD_PREP(PHY_R4_PHY_CR_DATA_IN, addr); 78 79 regmap_write(priv->regmap, PHY_R4, reg); 80 regmap_write(priv->regmap, PHY_R4, reg); 81 82 regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_CAP_ADDR); 83 84 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, 85 (val & PHY_R5_PHY_CR_ACK), 86 5, 1000); 87 if (ret) 88 return ret; 89 90 regmap_write(priv->regmap, PHY_R4, reg); 91 92 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, 93 !(val & PHY_R5_PHY_CR_ACK), 94 5, 1000); 95 if (ret) 96 return ret; 97 98 return 0; 99 } 100 101 static int phy_g12a_usb3_pcie_cr_bus_read(void *context, unsigned int addr, 102 unsigned int *data) 103 { 104 struct phy_g12a_usb3_pcie_priv *priv = context; 105 unsigned int val; 106 int ret; 107 108 ret = phy_g12a_usb3_pcie_cr_bus_addr(priv, addr); 109 if (ret) 110 return ret; 111 112 regmap_write(priv->regmap, PHY_R4, 0); 113 regmap_write(priv->regmap, PHY_R4, PHY_R4_PHY_CR_READ); 114 115 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, 116 (val & PHY_R5_PHY_CR_ACK), 117 5, 1000); 118 if (ret) 119 return ret; 120 121 *data = FIELD_GET(PHY_R5_PHY_CR_DATA_OUT, val); 122 123 regmap_write(priv->regmap, PHY_R4, 0); 124 125 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, 126 !(val & PHY_R5_PHY_CR_ACK), 127 5, 1000); 128 if (ret) 129 return ret; 130 131 return 0; 132 } 133 134 static int phy_g12a_usb3_pcie_cr_bus_write(void *context, unsigned int addr, 135 unsigned int data) 136 { 137 struct phy_g12a_usb3_pcie_priv *priv = context; 138 unsigned int val, reg; 139 int ret; 140 141 ret = phy_g12a_usb3_pcie_cr_bus_addr(priv, addr); 142 if (ret) 143 return ret; 144 145 reg = FIELD_PREP(PHY_R4_PHY_CR_DATA_IN, data); 146 147 regmap_write(priv->regmap, PHY_R4, reg); 148 regmap_write(priv->regmap, PHY_R4, reg); 149 150 regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_CAP_DATA); 151 152 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, 153 (val & PHY_R5_PHY_CR_ACK), 154 5, 1000); 155 if (ret) 156 return ret; 157 158 regmap_write(priv->regmap, PHY_R4, reg); 159 160 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, 161 (val & PHY_R5_PHY_CR_ACK) == 0, 162 5, 1000); 163 if (ret) 164 return ret; 165 166 regmap_write(priv->regmap, PHY_R4, reg); 167 168 regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_WRITE); 169 170 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, 171 (val & PHY_R5_PHY_CR_ACK), 172 5, 1000); 173 if (ret) 174 return ret; 175 176 regmap_write(priv->regmap, PHY_R4, reg); 177 178 ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, 179 (val & PHY_R5_PHY_CR_ACK) == 0, 180 5, 1000); 181 if (ret) 182 return ret; 183 184 return 0; 185 } 186 187 static const struct regmap_config phy_g12a_usb3_pcie_cr_regmap_conf = { 188 .reg_bits = 16, 189 .val_bits = 16, 190 .reg_read = phy_g12a_usb3_pcie_cr_bus_read, 191 .reg_write = phy_g12a_usb3_pcie_cr_bus_write, 192 .max_register = 0xffff, 193 .disable_locking = true, 194 }; 195 196 static int phy_g12a_usb3_init(struct phy *phy) 197 { 198 struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); 199 int data, ret; 200 201 ret = reset_control_reset(priv->reset); 202 if (ret) 203 return ret; 204 205 /* Switch PHY to USB3 */ 206 /* TODO figure out how to handle when PCIe was set in the bootloader */ 207 regmap_update_bits(priv->regmap, PHY_R0, 208 PHY_R0_PCIE_USB3_SWITCH, 209 PHY_R0_PCIE_USB3_SWITCH); 210 211 /* 212 * WORKAROUND: There is SSPHY suspend bug due to 213 * which USB enumerates 214 * in HS mode instead of SS mode. Workaround it by asserting 215 * LANE0.TX_ALT_BLOCK.EN_ALT_BUS to enable TX to use alt bus 216 * mode 217 */ 218 ret = regmap_update_bits(priv->regmap_cr, 0x102d, BIT(7), BIT(7)); 219 if (ret) 220 return ret; 221 222 ret = regmap_update_bits(priv->regmap_cr, 0x1010, 0xff0, 20); 223 if (ret) 224 return ret; 225 226 /* 227 * Fix RX Equalization setting as follows 228 * LANE0.RX_OVRD_IN_HI. RX_EQ_EN set to 0 229 * LANE0.RX_OVRD_IN_HI.RX_EQ_EN_OVRD set to 1 230 * LANE0.RX_OVRD_IN_HI.RX_EQ set to 3 231 * LANE0.RX_OVRD_IN_HI.RX_EQ_OVRD set to 1 232 */ 233 ret = regmap_read(priv->regmap_cr, 0x1006, &data); 234 if (ret) 235 return ret; 236 237 data &= ~BIT(6); 238 data |= BIT(7); 239 data &= ~(0x7 << 8); 240 data |= (0x3 << 8); 241 data |= (1 << 11); 242 ret = regmap_write(priv->regmap_cr, 0x1006, data); 243 if (ret) 244 return ret; 245 246 /* 247 * Set EQ and TX launch amplitudes as follows 248 * LANE0.TX_OVRD_DRV_LO.PREEMPH set to 22 249 * LANE0.TX_OVRD_DRV_LO.AMPLITUDE set to 127 250 * LANE0.TX_OVRD_DRV_LO.EN set to 1. 251 */ 252 ret = regmap_read(priv->regmap_cr, 0x1002, &data); 253 if (ret) 254 return ret; 255 256 data &= ~0x3f80; 257 data |= (0x16 << 7); 258 data &= ~0x7f; 259 data |= (0x7f | BIT(14)); 260 ret = regmap_write(priv->regmap_cr, 0x1002, data); 261 if (ret) 262 return ret; 263 264 /* MPLL_LOOP_CTL.PROP_CNTRL = 8 */ 265 ret = regmap_update_bits(priv->regmap_cr, 0x30, 0xf << 4, 8 << 4); 266 if (ret) 267 return ret; 268 269 regmap_update_bits(priv->regmap, PHY_R2, 270 PHY_R2_PHY_TX_VBOOST_LVL, 271 FIELD_PREP(PHY_R2_PHY_TX_VBOOST_LVL, 0x4)); 272 273 regmap_update_bits(priv->regmap, PHY_R1, 274 PHY_R1_PHY_LOS_BIAS | PHY_R1_PHY_LOS_LEVEL, 275 FIELD_PREP(PHY_R1_PHY_LOS_BIAS, 4) | 276 FIELD_PREP(PHY_R1_PHY_LOS_LEVEL, 9)); 277 278 return 0; 279 } 280 281 static int phy_g12a_usb3_pcie_power_on(struct phy *phy) 282 { 283 struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); 284 285 if (priv->mode == PHY_TYPE_USB3) 286 return 0; 287 288 regmap_update_bits(priv->regmap, PHY_R0, 289 PHY_R0_PCIE_POWER_STATE, 290 FIELD_PREP(PHY_R0_PCIE_POWER_STATE, 0x1c)); 291 292 return 0; 293 } 294 295 static int phy_g12a_usb3_pcie_power_off(struct phy *phy) 296 { 297 struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); 298 299 if (priv->mode == PHY_TYPE_USB3) 300 return 0; 301 302 regmap_update_bits(priv->regmap, PHY_R0, 303 PHY_R0_PCIE_POWER_STATE, 304 FIELD_PREP(PHY_R0_PCIE_POWER_STATE, 0x1d)); 305 306 return 0; 307 } 308 309 static int phy_g12a_usb3_pcie_reset(struct phy *phy) 310 { 311 struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); 312 int ret; 313 314 if (priv->mode == PHY_TYPE_USB3) 315 return 0; 316 317 ret = reset_control_assert(priv->reset); 318 if (ret) 319 return ret; 320 321 udelay(PCIE_RESET_DELAY); 322 323 ret = reset_control_deassert(priv->reset); 324 if (ret) 325 return ret; 326 327 udelay(PCIE_RESET_DELAY); 328 329 return 0; 330 } 331 332 static int phy_g12a_usb3_pcie_init(struct phy *phy) 333 { 334 struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); 335 336 if (priv->mode == PHY_TYPE_USB3) 337 return phy_g12a_usb3_init(phy); 338 339 return 0; 340 } 341 342 static int phy_g12a_usb3_pcie_exit(struct phy *phy) 343 { 344 struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); 345 346 if (priv->mode == PHY_TYPE_USB3) 347 return reset_control_reset(priv->reset); 348 349 return 0; 350 } 351 352 static struct phy *phy_g12a_usb3_pcie_xlate(struct device *dev, 353 struct of_phandle_args *args) 354 { 355 struct phy_g12a_usb3_pcie_priv *priv = dev_get_drvdata(dev); 356 unsigned int mode; 357 358 if (args->args_count < 1) { 359 dev_err(dev, "invalid number of arguments\n"); 360 return ERR_PTR(-EINVAL); 361 } 362 363 mode = args->args[0]; 364 365 if (mode != PHY_TYPE_USB3 && mode != PHY_TYPE_PCIE) { 366 dev_err(dev, "invalid phy mode select argument\n"); 367 return ERR_PTR(-EINVAL); 368 } 369 370 priv->mode = mode; 371 372 return priv->phy; 373 } 374 375 static const struct phy_ops phy_g12a_usb3_pcie_ops = { 376 .init = phy_g12a_usb3_pcie_init, 377 .exit = phy_g12a_usb3_pcie_exit, 378 .power_on = phy_g12a_usb3_pcie_power_on, 379 .power_off = phy_g12a_usb3_pcie_power_off, 380 .reset = phy_g12a_usb3_pcie_reset, 381 .owner = THIS_MODULE, 382 }; 383 384 static int phy_g12a_usb3_pcie_probe(struct platform_device *pdev) 385 { 386 struct device *dev = &pdev->dev; 387 struct device_node *np = dev->of_node; 388 struct phy_g12a_usb3_pcie_priv *priv; 389 struct phy_provider *phy_provider; 390 void __iomem *base; 391 392 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); 393 if (!priv) 394 return -ENOMEM; 395 396 base = devm_platform_ioremap_resource(pdev, 0); 397 if (IS_ERR(base)) 398 return PTR_ERR(base); 399 400 priv->regmap = devm_regmap_init_mmio(dev, base, 401 &phy_g12a_usb3_pcie_regmap_conf); 402 if (IS_ERR(priv->regmap)) 403 return PTR_ERR(priv->regmap); 404 405 priv->regmap_cr = devm_regmap_init(dev, NULL, priv, 406 &phy_g12a_usb3_pcie_cr_regmap_conf); 407 if (IS_ERR(priv->regmap_cr)) 408 return PTR_ERR(priv->regmap_cr); 409 410 priv->clk_ref = devm_clk_get_enabled(dev, "ref_clk"); 411 if (IS_ERR(priv->clk_ref)) 412 return PTR_ERR(priv->clk_ref); 413 414 priv->reset = devm_reset_control_array_get_exclusive(dev); 415 if (IS_ERR(priv->reset)) 416 return PTR_ERR(priv->reset); 417 418 priv->phy = devm_phy_create(dev, np, &phy_g12a_usb3_pcie_ops); 419 if (IS_ERR(priv->phy)) 420 return dev_err_probe(dev, PTR_ERR(priv->phy), "failed to create PHY\n"); 421 422 phy_set_drvdata(priv->phy, priv); 423 dev_set_drvdata(dev, priv); 424 425 phy_provider = devm_of_phy_provider_register(dev, 426 phy_g12a_usb3_pcie_xlate); 427 return PTR_ERR_OR_ZERO(phy_provider); 428 } 429 430 static const struct of_device_id phy_g12a_usb3_pcie_of_match[] = { 431 { .compatible = "amlogic,g12a-usb3-pcie-phy", }, 432 { }, 433 }; 434 MODULE_DEVICE_TABLE(of, phy_g12a_usb3_pcie_of_match); 435 436 static struct platform_driver phy_g12a_usb3_pcie_driver = { 437 .probe = phy_g12a_usb3_pcie_probe, 438 .driver = { 439 .name = "phy-g12a-usb3-pcie", 440 .of_match_table = phy_g12a_usb3_pcie_of_match, 441 }, 442 }; 443 module_platform_driver(phy_g12a_usb3_pcie_driver); 444 445 MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); 446 MODULE_DESCRIPTION("Amlogic G12A USB3 + PCIE Combo PHY driver"); 447 MODULE_LICENSE("GPL v2"); 448