1 /* 2 * This file contains work-arounds for many known PCI hardware 3 * bugs. Devices present only on certain architectures (host 4 * bridges et cetera) should be handled in arch-specific code. 5 * 6 * Note: any quirks for hotpluggable devices must _NOT_ be declared __init. 7 * 8 * Copyright (c) 1999 Martin Mares <mj@ucw.cz> 9 * 10 * Init/reset quirks for USB host controllers should be in the 11 * USB quirks file, where their drivers can access reuse it. 12 * 13 * The bridge optimization stuff has been removed. If you really 14 * have a silly BIOS which is unable to set your host bridge right, 15 * use the PowerTweak utility (see http://powertweak.sourceforge.net). 16 */ 17 18 #include <linux/config.h> 19 #include <linux/types.h> 20 #include <linux/kernel.h> 21 #include <linux/pci.h> 22 #include <linux/init.h> 23 #include <linux/delay.h> 24 #include <linux/acpi.h> 25 #include "pci.h" 26 27 /* Deal with broken BIOS'es that neglect to enable passive release, 28 which can cause problems in combination with the 82441FX/PPro MTRRs */ 29 static void __devinit quirk_passive_release(struct pci_dev *dev) 30 { 31 struct pci_dev *d = NULL; 32 unsigned char dlc; 33 34 /* We have to make sure a particular bit is set in the PIIX3 35 ISA bridge, so we have to go out and find it. */ 36 while ((d = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, d))) { 37 pci_read_config_byte(d, 0x82, &dlc); 38 if (!(dlc & 1<<1)) { 39 printk(KERN_ERR "PCI: PIIX3: Enabling Passive Release on %s\n", pci_name(d)); 40 dlc |= 1<<1; 41 pci_write_config_byte(d, 0x82, dlc); 42 } 43 } 44 } 45 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release ); 46 47 /* The VIA VP2/VP3/MVP3 seem to have some 'features'. There may be a workaround 48 but VIA don't answer queries. If you happen to have good contacts at VIA 49 ask them for me please -- Alan 50 51 This appears to be BIOS not version dependent. So presumably there is a 52 chipset level fix */ 53 int isa_dma_bridge_buggy; /* Exported */ 54 55 static void __devinit quirk_isa_dma_hangs(struct pci_dev *dev) 56 { 57 if (!isa_dma_bridge_buggy) { 58 isa_dma_bridge_buggy=1; 59 printk(KERN_INFO "Activating ISA DMA hang workarounds.\n"); 60 } 61 } 62 /* 63 * Its not totally clear which chipsets are the problematic ones 64 * We know 82C586 and 82C596 variants are affected. 65 */ 66 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_isa_dma_hangs ); 67 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C596, quirk_isa_dma_hangs ); 68 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, quirk_isa_dma_hangs ); 69 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, quirk_isa_dma_hangs ); 70 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_1, quirk_isa_dma_hangs ); 71 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_2, quirk_isa_dma_hangs ); 72 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_3, quirk_isa_dma_hangs ); 73 74 int pci_pci_problems; 75 76 /* 77 * Chipsets where PCI->PCI transfers vanish or hang 78 */ 79 static void __devinit quirk_nopcipci(struct pci_dev *dev) 80 { 81 if ((pci_pci_problems & PCIPCI_FAIL)==0) { 82 printk(KERN_INFO "Disabling direct PCI/PCI transfers.\n"); 83 pci_pci_problems |= PCIPCI_FAIL; 84 } 85 } 86 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5597, quirk_nopcipci ); 87 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_496, quirk_nopcipci ); 88 89 /* 90 * Triton requires workarounds to be used by the drivers 91 */ 92 static void __devinit quirk_triton(struct pci_dev *dev) 93 { 94 if ((pci_pci_problems&PCIPCI_TRITON)==0) { 95 printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n"); 96 pci_pci_problems |= PCIPCI_TRITON; 97 } 98 } 99 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437, quirk_triton ); 100 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437VX, quirk_triton ); 101 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439, quirk_triton ); 102 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439TX, quirk_triton ); 103 104 /* 105 * VIA Apollo KT133 needs PCI latency patch 106 * Made according to a windows driver based patch by George E. Breese 107 * see PCI Latency Adjust on http://www.viahardware.com/download/viatweak.shtm 108 * Also see http://www.au-ja.org/review-kt133a-1-en.phtml for 109 * the info on which Mr Breese based his work. 110 * 111 * Updated based on further information from the site and also on 112 * information provided by VIA 113 */ 114 static void __devinit quirk_vialatency(struct pci_dev *dev) 115 { 116 struct pci_dev *p; 117 u8 rev; 118 u8 busarb; 119 /* Ok we have a potential problem chipset here. Now see if we have 120 a buggy southbridge */ 121 122 p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, NULL); 123 if (p!=NULL) { 124 pci_read_config_byte(p, PCI_CLASS_REVISION, &rev); 125 /* 0x40 - 0x4f == 686B, 0x10 - 0x2f == 686A; thanks Dan Hollis */ 126 /* Check for buggy part revisions */ 127 if (rev < 0x40 || rev > 0x42) 128 goto exit; 129 } else { 130 p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, NULL); 131 if (p==NULL) /* No problem parts */ 132 goto exit; 133 pci_read_config_byte(p, PCI_CLASS_REVISION, &rev); 134 /* Check for buggy part revisions */ 135 if (rev < 0x10 || rev > 0x12) 136 goto exit; 137 } 138 139 /* 140 * Ok we have the problem. Now set the PCI master grant to 141 * occur every master grant. The apparent bug is that under high 142 * PCI load (quite common in Linux of course) you can get data 143 * loss when the CPU is held off the bus for 3 bus master requests 144 * This happens to include the IDE controllers.... 145 * 146 * VIA only apply this fix when an SB Live! is present but under 147 * both Linux and Windows this isnt enough, and we have seen 148 * corruption without SB Live! but with things like 3 UDMA IDE 149 * controllers. So we ignore that bit of the VIA recommendation.. 150 */ 151 152 pci_read_config_byte(dev, 0x76, &busarb); 153 /* Set bit 4 and bi 5 of byte 76 to 0x01 154 "Master priority rotation on every PCI master grant */ 155 busarb &= ~(1<<5); 156 busarb |= (1<<4); 157 pci_write_config_byte(dev, 0x76, busarb); 158 printk(KERN_INFO "Applying VIA southbridge workaround.\n"); 159 exit: 160 pci_dev_put(p); 161 } 162 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency ); 163 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency ); 164 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency ); 165 166 /* 167 * VIA Apollo VP3 needs ETBF on BT848/878 168 */ 169 static void __devinit quirk_viaetbf(struct pci_dev *dev) 170 { 171 if ((pci_pci_problems&PCIPCI_VIAETBF)==0) { 172 printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n"); 173 pci_pci_problems |= PCIPCI_VIAETBF; 174 } 175 } 176 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_viaetbf ); 177 178 static void __devinit quirk_vsfx(struct pci_dev *dev) 179 { 180 if ((pci_pci_problems&PCIPCI_VSFX)==0) { 181 printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n"); 182 pci_pci_problems |= PCIPCI_VSFX; 183 } 184 } 185 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C576, quirk_vsfx ); 186 187 /* 188 * Ali Magik requires workarounds to be used by the drivers 189 * that DMA to AGP space. Latency must be set to 0xA and triton 190 * workaround applied too 191 * [Info kindly provided by ALi] 192 */ 193 static void __init quirk_alimagik(struct pci_dev *dev) 194 { 195 if ((pci_pci_problems&PCIPCI_ALIMAGIK)==0) { 196 printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n"); 197 pci_pci_problems |= PCIPCI_ALIMAGIK|PCIPCI_TRITON; 198 } 199 } 200 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1647, quirk_alimagik ); 201 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1651, quirk_alimagik ); 202 203 /* 204 * Natoma has some interesting boundary conditions with Zoran stuff 205 * at least 206 */ 207 static void __devinit quirk_natoma(struct pci_dev *dev) 208 { 209 if ((pci_pci_problems&PCIPCI_NATOMA)==0) { 210 printk(KERN_INFO "Limiting direct PCI/PCI transfers.\n"); 211 pci_pci_problems |= PCIPCI_NATOMA; 212 } 213 } 214 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_natoma ); 215 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_0, quirk_natoma ); 216 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_1, quirk_natoma ); 217 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_0, quirk_natoma ); 218 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_1, quirk_natoma ); 219 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_2, quirk_natoma ); 220 221 /* 222 * This chip can cause PCI parity errors if config register 0xA0 is read 223 * while DMAs are occurring. 224 */ 225 static void __devinit quirk_citrine(struct pci_dev *dev) 226 { 227 dev->cfg_size = 0xA0; 228 } 229 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, PCI_DEVICE_ID_IBM_CITRINE, quirk_citrine ); 230 231 /* 232 * S3 868 and 968 chips report region size equal to 32M, but they decode 64M. 233 * If it's needed, re-allocate the region. 234 */ 235 static void __devinit quirk_s3_64M(struct pci_dev *dev) 236 { 237 struct resource *r = &dev->resource[0]; 238 239 if ((r->start & 0x3ffffff) || r->end != r->start + 0x3ffffff) { 240 r->start = 0; 241 r->end = 0x3ffffff; 242 } 243 } 244 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_868, quirk_s3_64M ); 245 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_968, quirk_s3_64M ); 246 247 static void __devinit quirk_io_region(struct pci_dev *dev, unsigned region, 248 unsigned size, int nr, const char *name) 249 { 250 region &= ~(size-1); 251 if (region) { 252 struct pci_bus_region bus_region; 253 struct resource *res = dev->resource + nr; 254 255 res->name = pci_name(dev); 256 res->start = region; 257 res->end = region + size - 1; 258 res->flags = IORESOURCE_IO; 259 260 /* Convert from PCI bus to resource space. */ 261 bus_region.start = res->start; 262 bus_region.end = res->end; 263 pcibios_bus_to_resource(dev, res, &bus_region); 264 265 pci_claim_resource(dev, nr); 266 printk("PCI quirk: region %04x-%04x claimed by %s\n", region, region + size - 1, name); 267 } 268 } 269 270 /* 271 * ATI Northbridge setups MCE the processor if you even 272 * read somewhere between 0x3b0->0x3bb or read 0x3d3 273 */ 274 static void __devinit quirk_ati_exploding_mce(struct pci_dev *dev) 275 { 276 printk(KERN_INFO "ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb.\n"); 277 /* Mae rhaid i ni beidio ag edrych ar y lleoliadiau I/O hyn */ 278 request_region(0x3b0, 0x0C, "RadeonIGP"); 279 request_region(0x3d3, 0x01, "RadeonIGP"); 280 } 281 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS100, quirk_ati_exploding_mce ); 282 283 /* 284 * Let's make the southbridge information explicit instead 285 * of having to worry about people probing the ACPI areas, 286 * for example.. (Yes, it happens, and if you read the wrong 287 * ACPI register it will put the machine to sleep with no 288 * way of waking it up again. Bummer). 289 * 290 * ALI M7101: Two IO regions pointed to by words at 291 * 0xE0 (64 bytes of ACPI registers) 292 * 0xE2 (32 bytes of SMB registers) 293 */ 294 static void __devinit quirk_ali7101_acpi(struct pci_dev *dev) 295 { 296 u16 region; 297 298 pci_read_config_word(dev, 0xE0, ®ion); 299 quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES, "ali7101 ACPI"); 300 pci_read_config_word(dev, 0xE2, ®ion); 301 quirk_io_region(dev, region, 32, PCI_BRIDGE_RESOURCES+1, "ali7101 SMB"); 302 } 303 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101, quirk_ali7101_acpi ); 304 305 static void piix4_io_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable) 306 { 307 u32 devres; 308 u32 mask, size, base; 309 310 pci_read_config_dword(dev, port, &devres); 311 if ((devres & enable) != enable) 312 return; 313 mask = (devres >> 16) & 15; 314 base = devres & 0xffff; 315 size = 16; 316 for (;;) { 317 unsigned bit = size >> 1; 318 if ((bit & mask) == bit) 319 break; 320 size = bit; 321 } 322 /* 323 * For now we only print it out. Eventually we'll want to 324 * reserve it (at least if it's in the 0x1000+ range), but 325 * let's get enough confirmation reports first. 326 */ 327 base &= -size; 328 printk("%s PIO at %04x-%04x\n", name, base, base + size - 1); 329 } 330 331 static void piix4_mem_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable) 332 { 333 u32 devres; 334 u32 mask, size, base; 335 336 pci_read_config_dword(dev, port, &devres); 337 if ((devres & enable) != enable) 338 return; 339 base = devres & 0xffff0000; 340 mask = (devres & 0x3f) << 16; 341 size = 128 << 16; 342 for (;;) { 343 unsigned bit = size >> 1; 344 if ((bit & mask) == bit) 345 break; 346 size = bit; 347 } 348 /* 349 * For now we only print it out. Eventually we'll want to 350 * reserve it, but let's get enough confirmation reports first. 351 */ 352 base &= -size; 353 printk("%s MMIO at %04x-%04x\n", name, base, base + size - 1); 354 } 355 356 /* 357 * PIIX4 ACPI: Two IO regions pointed to by longwords at 358 * 0x40 (64 bytes of ACPI registers) 359 * 0x90 (16 bytes of SMB registers) 360 * and a few strange programmable PIIX4 device resources. 361 */ 362 static void __devinit quirk_piix4_acpi(struct pci_dev *dev) 363 { 364 u32 region, res_a; 365 366 pci_read_config_dword(dev, 0x40, ®ion); 367 quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES, "PIIX4 ACPI"); 368 pci_read_config_dword(dev, 0x90, ®ion); 369 quirk_io_region(dev, region, 16, PCI_BRIDGE_RESOURCES+1, "PIIX4 SMB"); 370 371 /* Device resource A has enables for some of the other ones */ 372 pci_read_config_dword(dev, 0x5c, &res_a); 373 374 piix4_io_quirk(dev, "PIIX4 devres B", 0x60, 3 << 21); 375 piix4_io_quirk(dev, "PIIX4 devres C", 0x64, 3 << 21); 376 377 /* Device resource D is just bitfields for static resources */ 378 379 /* Device 12 enabled? */ 380 if (res_a & (1 << 29)) { 381 piix4_io_quirk(dev, "PIIX4 devres E", 0x68, 1 << 20); 382 piix4_mem_quirk(dev, "PIIX4 devres F", 0x6c, 1 << 7); 383 } 384 /* Device 13 enabled? */ 385 if (res_a & (1 << 30)) { 386 piix4_io_quirk(dev, "PIIX4 devres G", 0x70, 1 << 20); 387 piix4_mem_quirk(dev, "PIIX4 devres H", 0x74, 1 << 7); 388 } 389 piix4_io_quirk(dev, "PIIX4 devres I", 0x78, 1 << 20); 390 piix4_io_quirk(dev, "PIIX4 devres J", 0x7c, 1 << 20); 391 } 392 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, quirk_piix4_acpi ); 393 394 /* 395 * ICH4, ICH4-M, ICH5, ICH5-M ACPI: Three IO regions pointed to by longwords at 396 * 0x40 (128 bytes of ACPI, GPIO & TCO registers) 397 * 0x58 (64 bytes of GPIO I/O space) 398 */ 399 static void __devinit quirk_ich4_lpc_acpi(struct pci_dev *dev) 400 { 401 u32 region; 402 403 pci_read_config_dword(dev, 0x40, ®ion); 404 quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES, "ICH4 ACPI/GPIO/TCO"); 405 406 pci_read_config_dword(dev, 0x58, ®ion); 407 quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES+1, "ICH4 GPIO"); 408 } 409 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, quirk_ich4_lpc_acpi ); 410 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_0, quirk_ich4_lpc_acpi ); 411 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, quirk_ich4_lpc_acpi ); 412 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_10, quirk_ich4_lpc_acpi ); 413 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, quirk_ich4_lpc_acpi ); 414 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, quirk_ich4_lpc_acpi ); 415 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, quirk_ich4_lpc_acpi ); 416 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, quirk_ich4_lpc_acpi ); 417 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, quirk_ich4_lpc_acpi ); 418 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_1, quirk_ich4_lpc_acpi ); 419 420 static void __devinit quirk_ich6_lpc_acpi(struct pci_dev *dev) 421 { 422 u32 region; 423 424 pci_read_config_dword(dev, 0x40, ®ion); 425 quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES, "ICH6 ACPI/GPIO/TCO"); 426 427 pci_read_config_dword(dev, 0x48, ®ion); 428 quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES+1, "ICH6 GPIO"); 429 } 430 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, quirk_ich6_lpc_acpi ); 431 432 /* 433 * VIA ACPI: One IO region pointed to by longword at 434 * 0x48 or 0x20 (256 bytes of ACPI registers) 435 */ 436 static void __devinit quirk_vt82c586_acpi(struct pci_dev *dev) 437 { 438 u8 rev; 439 u32 region; 440 441 pci_read_config_byte(dev, PCI_CLASS_REVISION, &rev); 442 if (rev & 0x10) { 443 pci_read_config_dword(dev, 0x48, ®ion); 444 region &= PCI_BASE_ADDRESS_IO_MASK; 445 quirk_io_region(dev, region, 256, PCI_BRIDGE_RESOURCES, "vt82c586 ACPI"); 446 } 447 } 448 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_vt82c586_acpi ); 449 450 /* 451 * VIA VT82C686 ACPI: Three IO region pointed to by (long)words at 452 * 0x48 (256 bytes of ACPI registers) 453 * 0x70 (128 bytes of hardware monitoring register) 454 * 0x90 (16 bytes of SMB registers) 455 */ 456 static void __devinit quirk_vt82c686_acpi(struct pci_dev *dev) 457 { 458 u16 hm; 459 u32 smb; 460 461 quirk_vt82c586_acpi(dev); 462 463 pci_read_config_word(dev, 0x70, &hm); 464 hm &= PCI_BASE_ADDRESS_IO_MASK; 465 quirk_io_region(dev, hm, 128, PCI_BRIDGE_RESOURCES + 1, "vt82c686 HW-mon"); 466 467 pci_read_config_dword(dev, 0x90, &smb); 468 smb &= PCI_BASE_ADDRESS_IO_MASK; 469 quirk_io_region(dev, smb, 16, PCI_BRIDGE_RESOURCES + 2, "vt82c686 SMB"); 470 } 471 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_vt82c686_acpi ); 472 473 /* 474 * VIA VT8235 ISA Bridge: Two IO regions pointed to by words at 475 * 0x88 (128 bytes of power management registers) 476 * 0xd0 (16 bytes of SMB registers) 477 */ 478 static void __devinit quirk_vt8235_acpi(struct pci_dev *dev) 479 { 480 u16 pm, smb; 481 482 pci_read_config_word(dev, 0x88, &pm); 483 pm &= PCI_BASE_ADDRESS_IO_MASK; 484 quirk_io_region(dev, pm, 128, PCI_BRIDGE_RESOURCES, "vt8235 PM"); 485 486 pci_read_config_word(dev, 0xd0, &smb); 487 smb &= PCI_BASE_ADDRESS_IO_MASK; 488 quirk_io_region(dev, smb, 16, PCI_BRIDGE_RESOURCES + 1, "vt8235 SMB"); 489 } 490 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_vt8235_acpi); 491 492 493 #ifdef CONFIG_X86_IO_APIC 494 495 #include <asm/io_apic.h> 496 497 /* 498 * VIA 686A/B: If an IO-APIC is active, we need to route all on-chip 499 * devices to the external APIC. 500 * 501 * TODO: When we have device-specific interrupt routers, 502 * this code will go away from quirks. 503 */ 504 static void __devinit quirk_via_ioapic(struct pci_dev *dev) 505 { 506 u8 tmp; 507 508 if (nr_ioapics < 1) 509 tmp = 0; /* nothing routed to external APIC */ 510 else 511 tmp = 0x1f; /* all known bits (4-0) routed to external APIC */ 512 513 printk(KERN_INFO "PCI: %sbling Via external APIC routing\n", 514 tmp == 0 ? "Disa" : "Ena"); 515 516 /* Offset 0x58: External APIC IRQ output control */ 517 pci_write_config_byte (dev, 0x58, tmp); 518 } 519 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic ); 520 521 /* 522 * VIA 8237: Some BIOSs don't set the 'Bypass APIC De-Assert Message' Bit. 523 * This leads to doubled level interrupt rates. 524 * Set this bit to get rid of cycle wastage. 525 * Otherwise uncritical. 526 */ 527 static void __devinit quirk_via_vt8237_bypass_apic_deassert(struct pci_dev *dev) 528 { 529 u8 misc_control2; 530 #define BYPASS_APIC_DEASSERT 8 531 532 pci_read_config_byte(dev, 0x5B, &misc_control2); 533 if (!(misc_control2 & BYPASS_APIC_DEASSERT)) { 534 printk(KERN_INFO "PCI: Bypassing VIA 8237 APIC De-Assert Message\n"); 535 pci_write_config_byte(dev, 0x5B, misc_control2|BYPASS_APIC_DEASSERT); 536 } 537 } 538 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_vt8237_bypass_apic_deassert); 539 540 /* 541 * The AMD io apic can hang the box when an apic irq is masked. 542 * We check all revs >= B0 (yet not in the pre production!) as the bug 543 * is currently marked NoFix 544 * 545 * We have multiple reports of hangs with this chipset that went away with 546 * noapic specified. For the moment we assume its the errata. We may be wrong 547 * of course. However the advice is demonstrably good even if so.. 548 */ 549 static void __devinit quirk_amd_ioapic(struct pci_dev *dev) 550 { 551 u8 rev; 552 553 pci_read_config_byte(dev, PCI_REVISION_ID, &rev); 554 if (rev >= 0x02) { 555 printk(KERN_WARNING "I/O APIC: AMD Errata #22 may be present. In the event of instability try\n"); 556 printk(KERN_WARNING " : booting with the \"noapic\" option.\n"); 557 } 558 } 559 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7410, quirk_amd_ioapic ); 560 561 static void __init quirk_ioapic_rmw(struct pci_dev *dev) 562 { 563 if (dev->devfn == 0 && dev->bus->number == 0) 564 sis_apic_bug = 1; 565 } 566 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_ANY_ID, quirk_ioapic_rmw ); 567 568 int pci_msi_quirk; 569 570 #define AMD8131_revA0 0x01 571 #define AMD8131_revB0 0x11 572 #define AMD8131_MISC 0x40 573 #define AMD8131_NIOAMODE_BIT 0 574 static void __init quirk_amd_8131_ioapic(struct pci_dev *dev) 575 { 576 unsigned char revid, tmp; 577 578 if (dev->subordinate) { 579 printk(KERN_WARNING "PCI: MSI quirk detected. " 580 "PCI_BUS_FLAGS_NO_MSI set for subordinate bus.\n"); 581 dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI; 582 } 583 584 if (nr_ioapics == 0) 585 return; 586 587 pci_read_config_byte(dev, PCI_REVISION_ID, &revid); 588 if (revid == AMD8131_revA0 || revid == AMD8131_revB0) { 589 printk(KERN_INFO "Fixing up AMD8131 IOAPIC mode\n"); 590 pci_read_config_byte( dev, AMD8131_MISC, &tmp); 591 tmp &= ~(1 << AMD8131_NIOAMODE_BIT); 592 pci_write_config_byte( dev, AMD8131_MISC, tmp); 593 } 594 } 595 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_amd_8131_ioapic); 596 597 static void __init quirk_svw_msi(struct pci_dev *dev) 598 { 599 pci_msi_quirk = 1; 600 printk(KERN_WARNING "PCI: MSI quirk detected. pci_msi_quirk set.\n"); 601 } 602 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_GCNB_LE, quirk_svw_msi ); 603 #endif /* CONFIG_X86_IO_APIC */ 604 605 606 /* 607 * FIXME: it is questionable that quirk_via_acpi 608 * is needed. It shows up as an ISA bridge, and does not 609 * support the PCI_INTERRUPT_LINE register at all. Therefore 610 * it seems like setting the pci_dev's 'irq' to the 611 * value of the ACPI SCI interrupt is only done for convenience. 612 * -jgarzik 613 */ 614 static void __devinit quirk_via_acpi(struct pci_dev *d) 615 { 616 /* 617 * VIA ACPI device: SCI IRQ line in PCI config byte 0x42 618 */ 619 u8 irq; 620 pci_read_config_byte(d, 0x42, &irq); 621 irq &= 0xf; 622 if (irq && (irq != 2)) 623 d->irq = irq; 624 } 625 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_acpi ); 626 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_acpi ); 627 628 /* 629 * Via 686A/B: The PCI_INTERRUPT_LINE register for the on-chip 630 * devices, USB0/1, AC97, MC97, and ACPI, has an unusual feature: 631 * when written, it makes an internal connection to the PIC. 632 * For these devices, this register is defined to be 4 bits wide. 633 * Normally this is fine. However for IO-APIC motherboards, or 634 * non-x86 architectures (yes Via exists on PPC among other places), 635 * we must mask the PCI_INTERRUPT_LINE value versus 0xf to get 636 * interrupts delivered properly. 637 * 638 * Some of the on-chip devices are actually '586 devices' so they are 639 * listed here. 640 */ 641 static void quirk_via_irq(struct pci_dev *dev) 642 { 643 u8 irq, new_irq; 644 645 new_irq = dev->irq & 0xf; 646 pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq); 647 if (new_irq != irq) { 648 printk(KERN_INFO "PCI: VIA IRQ fixup for %s, from %d to %d\n", 649 pci_name(dev), irq, new_irq); 650 udelay(15); /* unknown if delay really needed */ 651 pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq); 652 } 653 } 654 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_via_irq); 655 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1, quirk_via_irq); 656 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_2, quirk_via_irq); 657 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_irq); 658 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_irq); 659 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_irq); 660 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_5, quirk_via_irq); 661 662 /* 663 * VIA VT82C598 has its device ID settable and many BIOSes 664 * set it to the ID of VT82C597 for backward compatibility. 665 * We need to switch it off to be able to recognize the real 666 * type of the chip. 667 */ 668 static void __devinit quirk_vt82c598_id(struct pci_dev *dev) 669 { 670 pci_write_config_byte(dev, 0xfc, 0); 671 pci_read_config_word(dev, PCI_DEVICE_ID, &dev->device); 672 } 673 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_vt82c598_id ); 674 675 /* 676 * CardBus controllers have a legacy base address that enables them 677 * to respond as i82365 pcmcia controllers. We don't want them to 678 * do this even if the Linux CardBus driver is not loaded, because 679 * the Linux i82365 driver does not (and should not) handle CardBus. 680 */ 681 static void __devinit quirk_cardbus_legacy(struct pci_dev *dev) 682 { 683 if ((PCI_CLASS_BRIDGE_CARDBUS << 8) ^ dev->class) 684 return; 685 pci_write_config_dword(dev, PCI_CB_LEGACY_MODE_BASE, 0); 686 } 687 DECLARE_PCI_FIXUP_FINAL(PCI_ANY_ID, PCI_ANY_ID, quirk_cardbus_legacy); 688 689 /* 690 * Following the PCI ordering rules is optional on the AMD762. I'm not 691 * sure what the designers were smoking but let's not inhale... 692 * 693 * To be fair to AMD, it follows the spec by default, its BIOS people 694 * who turn it off! 695 */ 696 static void __devinit quirk_amd_ordering(struct pci_dev *dev) 697 { 698 u32 pcic; 699 pci_read_config_dword(dev, 0x4C, &pcic); 700 if ((pcic&6)!=6) { 701 pcic |= 6; 702 printk(KERN_WARNING "BIOS failed to enable PCI standards compliance, fixing this error.\n"); 703 pci_write_config_dword(dev, 0x4C, pcic); 704 pci_read_config_dword(dev, 0x84, &pcic); 705 pcic |= (1<<23); /* Required in this mode */ 706 pci_write_config_dword(dev, 0x84, pcic); 707 } 708 } 709 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering ); 710 711 /* 712 * DreamWorks provided workaround for Dunord I-3000 problem 713 * 714 * This card decodes and responds to addresses not apparently 715 * assigned to it. We force a larger allocation to ensure that 716 * nothing gets put too close to it. 717 */ 718 static void __devinit quirk_dunord ( struct pci_dev * dev ) 719 { 720 struct resource *r = &dev->resource [1]; 721 r->start = 0; 722 r->end = 0xffffff; 723 } 724 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_DUNORD, PCI_DEVICE_ID_DUNORD_I3000, quirk_dunord ); 725 726 /* 727 * i82380FB mobile docking controller: its PCI-to-PCI bridge 728 * is subtractive decoding (transparent), and does indicate this 729 * in the ProgIf. Unfortunately, the ProgIf value is wrong - 0x80 730 * instead of 0x01. 731 */ 732 static void __devinit quirk_transparent_bridge(struct pci_dev *dev) 733 { 734 dev->transparent = 1; 735 } 736 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82380FB, quirk_transparent_bridge ); 737 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA, 0x605, quirk_transparent_bridge ); 738 739 /* 740 * Common misconfiguration of the MediaGX/Geode PCI master that will 741 * reduce PCI bandwidth from 70MB/s to 25MB/s. See the GXM/GXLV/GX1 742 * datasheets found at http://www.national.com/ds/GX for info on what 743 * these bits do. <christer@weinigel.se> 744 */ 745 static void __init quirk_mediagx_master(struct pci_dev *dev) 746 { 747 u8 reg; 748 pci_read_config_byte(dev, 0x41, ®); 749 if (reg & 2) { 750 reg &= ~2; 751 printk(KERN_INFO "PCI: Fixup for MediaGX/Geode Slave Disconnect Boundary (0x41=0x%02x)\n", reg); 752 pci_write_config_byte(dev, 0x41, reg); 753 } 754 } 755 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master ); 756 757 /* 758 * As per PCI spec, ignore base address registers 0-3 of the IDE controllers 759 * running in Compatible mode (bits 0 and 2 in the ProgIf for primary and 760 * secondary channels respectively). If the device reports Compatible mode 761 * but does use BAR0-3 for address decoding, we assume that firmware has 762 * programmed these BARs with standard values (0x1f0,0x3f4 and 0x170,0x374). 763 * Exceptions (if they exist) must be handled in chip/architecture specific 764 * fixups. 765 * 766 * Note: for non x86 people. You may need an arch specific quirk to handle 767 * moving IDE devices to native mode as well. Some plug in card devices power 768 * up in compatible mode and assume the BIOS will adjust them. 769 * 770 * Q: should we load the 0x1f0,0x3f4 into the registers or zap them as 771 * we do now ? We don't want is pci_enable_device to come along 772 * and assign new resources. Both approaches work for that. 773 */ 774 static void __devinit quirk_ide_bases(struct pci_dev *dev) 775 { 776 struct resource *res; 777 int first_bar = 2, last_bar = 0; 778 779 if ((dev->class >> 8) != PCI_CLASS_STORAGE_IDE) 780 return; 781 782 res = &dev->resource[0]; 783 784 /* primary channel: ProgIf bit 0, BAR0, BAR1 */ 785 if (!(dev->class & 1) && (res[0].flags || res[1].flags)) { 786 res[0].start = res[0].end = res[0].flags = 0; 787 res[1].start = res[1].end = res[1].flags = 0; 788 first_bar = 0; 789 last_bar = 1; 790 } 791 792 /* secondary channel: ProgIf bit 2, BAR2, BAR3 */ 793 if (!(dev->class & 4) && (res[2].flags || res[3].flags)) { 794 res[2].start = res[2].end = res[2].flags = 0; 795 res[3].start = res[3].end = res[3].flags = 0; 796 last_bar = 3; 797 } 798 799 if (!last_bar) 800 return; 801 802 printk(KERN_INFO "PCI: Ignoring BAR%d-%d of IDE controller %s\n", 803 first_bar, last_bar, pci_name(dev)); 804 } 805 DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_ide_bases); 806 807 /* 808 * Ensure C0 rev restreaming is off. This is normally done by 809 * the BIOS but in the odd case it is not the results are corruption 810 * hence the presence of a Linux check 811 */ 812 static void __init quirk_disable_pxb(struct pci_dev *pdev) 813 { 814 u16 config; 815 u8 rev; 816 817 pci_read_config_byte(pdev, PCI_REVISION_ID, &rev); 818 if (rev != 0x04) /* Only C0 requires this */ 819 return; 820 pci_read_config_word(pdev, 0x40, &config); 821 if (config & (1<<6)) { 822 config &= ~(1<<6); 823 pci_write_config_word(pdev, 0x40, config); 824 printk(KERN_INFO "PCI: C0 revision 450NX. Disabling PCI restreaming.\n"); 825 } 826 } 827 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb ); 828 829 830 /* 831 * Serverworks CSB5 IDE does not fully support native mode 832 */ 833 static void __devinit quirk_svwks_csb5ide(struct pci_dev *pdev) 834 { 835 u8 prog; 836 pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); 837 if (prog & 5) { 838 prog &= ~5; 839 pdev->class &= ~5; 840 pci_write_config_byte(pdev, PCI_CLASS_PROG, prog); 841 /* need to re-assign BARs for compat mode */ 842 quirk_ide_bases(pdev); 843 } 844 } 845 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, quirk_svwks_csb5ide ); 846 847 /* 848 * Intel 82801CAM ICH3-M datasheet says IDE modes must be the same 849 */ 850 static void __init quirk_ide_samemode(struct pci_dev *pdev) 851 { 852 u8 prog; 853 854 pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); 855 856 if (((prog & 1) && !(prog & 4)) || ((prog & 4) && !(prog & 1))) { 857 printk(KERN_INFO "PCI: IDE mode mismatch; forcing legacy mode\n"); 858 prog &= ~5; 859 pdev->class &= ~5; 860 pci_write_config_byte(pdev, PCI_CLASS_PROG, prog); 861 /* need to re-assign BARs for compat mode */ 862 quirk_ide_bases(pdev); 863 } 864 } 865 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, quirk_ide_samemode); 866 867 /* This was originally an Alpha specific thing, but it really fits here. 868 * The i82375 PCI/EISA bridge appears as non-classified. Fix that. 869 */ 870 static void __init quirk_eisa_bridge(struct pci_dev *dev) 871 { 872 dev->class = PCI_CLASS_BRIDGE_EISA << 8; 873 } 874 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82375, quirk_eisa_bridge ); 875 876 /* 877 * On the MSI-K8T-Neo2Fir Board, the internal Soundcard is disabled 878 * when a PCI-Soundcard is added. The BIOS only gives Options 879 * "Disabled" and "AUTO". This Quirk Sets the corresponding 880 * Register-Value to enable the Soundcard. 881 */ 882 static void __init k8t_sound_hostbridge(struct pci_dev *dev) 883 { 884 unsigned char val; 885 886 printk(KERN_INFO "PCI: Quirk-MSI-K8T Soundcard On\n"); 887 pci_read_config_byte(dev, 0x50, &val); 888 if (val == 0x88 || val == 0xc8) { 889 pci_write_config_byte(dev, 0x50, val & (~0x40)); 890 891 /* Verify the Change for Status output */ 892 pci_read_config_byte(dev, 0x50, &val); 893 if (val & 0x40) 894 printk(KERN_INFO "PCI: MSI-K8T soundcard still off\n"); 895 else 896 printk(KERN_INFO "PCI: MSI-K8T soundcard on\n"); 897 } else { 898 printk(KERN_INFO "PCI: Unexpected Value in PCI-Register: " 899 "no Change!\n"); 900 } 901 902 } 903 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, k8t_sound_hostbridge); 904 905 #ifndef CONFIG_ACPI_SLEEP 906 /* 907 * On ASUS P4B boards, the SMBus PCI Device within the ICH2/4 southbridge 908 * is not activated. The myth is that Asus said that they do not want the 909 * users to be irritated by just another PCI Device in the Win98 device 910 * manager. (see the file prog/hotplug/README.p4b in the lm_sensors 911 * package 2.7.0 for details) 912 * 913 * The SMBus PCI Device can be activated by setting a bit in the ICH LPC 914 * bridge. Unfortunately, this device has no subvendor/subdevice ID. So it 915 * becomes necessary to do this tweak in two steps -- I've chosen the Host 916 * bridge as trigger. 917 * 918 * Actually, leaving it unhidden and not redoing the quirk over suspend2ram 919 * will cause thermal management to break down, and causing machine to 920 * overheat. 921 */ 922 static int __initdata asus_hides_smbus; 923 924 static void __init asus_hides_smbus_hostbridge(struct pci_dev *dev) 925 { 926 if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) { 927 if (dev->device == PCI_DEVICE_ID_INTEL_82845_HB) 928 switch(dev->subsystem_device) { 929 case 0x8025: /* P4B-LX */ 930 case 0x8070: /* P4B */ 931 case 0x8088: /* P4B533 */ 932 case 0x1626: /* L3C notebook */ 933 asus_hides_smbus = 1; 934 } 935 if (dev->device == PCI_DEVICE_ID_INTEL_82845G_HB) 936 switch(dev->subsystem_device) { 937 case 0x80b1: /* P4GE-V */ 938 case 0x80b2: /* P4PE */ 939 case 0x8093: /* P4B533-V */ 940 asus_hides_smbus = 1; 941 } 942 if (dev->device == PCI_DEVICE_ID_INTEL_82850_HB) 943 switch(dev->subsystem_device) { 944 case 0x8030: /* P4T533 */ 945 asus_hides_smbus = 1; 946 } 947 if (dev->device == PCI_DEVICE_ID_INTEL_7205_0) 948 switch (dev->subsystem_device) { 949 case 0x8070: /* P4G8X Deluxe */ 950 asus_hides_smbus = 1; 951 } 952 if (dev->device == PCI_DEVICE_ID_INTEL_82855GM_HB) 953 switch (dev->subsystem_device) { 954 case 0x1751: /* M2N notebook */ 955 case 0x1821: /* M5N notebook */ 956 asus_hides_smbus = 1; 957 } 958 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 959 switch (dev->subsystem_device) { 960 case 0x184b: /* W1N notebook */ 961 case 0x186a: /* M6Ne notebook */ 962 asus_hides_smbus = 1; 963 } 964 if (dev->device == PCI_DEVICE_ID_INTEL_82915GM_HB) { 965 switch (dev->subsystem_device) { 966 case 0x1882: /* M6V notebook */ 967 case 0x1977: /* A6VA notebook */ 968 asus_hides_smbus = 1; 969 } 970 } 971 } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_HP)) { 972 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 973 switch(dev->subsystem_device) { 974 case 0x088C: /* HP Compaq nc8000 */ 975 case 0x0890: /* HP Compaq nc6000 */ 976 asus_hides_smbus = 1; 977 } 978 if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB) 979 switch (dev->subsystem_device) { 980 case 0x12bc: /* HP D330L */ 981 case 0x12bd: /* HP D530 */ 982 asus_hides_smbus = 1; 983 } 984 if (dev->device == PCI_DEVICE_ID_INTEL_82915GM_HB) { 985 switch (dev->subsystem_device) { 986 case 0x099c: /* HP Compaq nx6110 */ 987 asus_hides_smbus = 1; 988 } 989 } 990 } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_TOSHIBA)) { 991 if (dev->device == PCI_DEVICE_ID_INTEL_82855GM_HB) 992 switch(dev->subsystem_device) { 993 case 0x0001: /* Toshiba Satellite A40 */ 994 asus_hides_smbus = 1; 995 } 996 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 997 switch(dev->subsystem_device) { 998 case 0x0001: /* Toshiba Tecra M2 */ 999 asus_hides_smbus = 1; 1000 } 1001 } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG)) { 1002 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 1003 switch(dev->subsystem_device) { 1004 case 0xC00C: /* Samsung P35 notebook */ 1005 asus_hides_smbus = 1; 1006 } 1007 } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_COMPAQ)) { 1008 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 1009 switch(dev->subsystem_device) { 1010 case 0x0058: /* Compaq Evo N620c */ 1011 asus_hides_smbus = 1; 1012 } 1013 } 1014 } 1015 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845_HB, asus_hides_smbus_hostbridge ); 1016 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845G_HB, asus_hides_smbus_hostbridge ); 1017 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82850_HB, asus_hides_smbus_hostbridge ); 1018 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB, asus_hides_smbus_hostbridge ); 1019 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_7205_0, asus_hides_smbus_hostbridge ); 1020 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855PM_HB, asus_hides_smbus_hostbridge ); 1021 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855GM_HB, asus_hides_smbus_hostbridge ); 1022 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82915GM_HB, asus_hides_smbus_hostbridge ); 1023 1024 static void __init asus_hides_smbus_lpc(struct pci_dev *dev) 1025 { 1026 u16 val; 1027 1028 if (likely(!asus_hides_smbus)) 1029 return; 1030 1031 pci_read_config_word(dev, 0xF2, &val); 1032 if (val & 0x8) { 1033 pci_write_config_word(dev, 0xF2, val & (~0x8)); 1034 pci_read_config_word(dev, 0xF2, &val); 1035 if (val & 0x8) 1036 printk(KERN_INFO "PCI: i801 SMBus device continues to play 'hide and seek'! 0x%x\n", val); 1037 else 1038 printk(KERN_INFO "PCI: Enabled i801 SMBus device\n"); 1039 } 1040 } 1041 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc ); 1042 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc ); 1043 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc ); 1044 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc ); 1045 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc ); 1046 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc ); 1047 1048 static void __init asus_hides_smbus_lpc_ich6(struct pci_dev *dev) 1049 { 1050 u32 val, rcba; 1051 void __iomem *base; 1052 1053 if (likely(!asus_hides_smbus)) 1054 return; 1055 pci_read_config_dword(dev, 0xF0, &rcba); 1056 base = ioremap_nocache(rcba & 0xFFFFC000, 0x4000); /* use bits 31:14, 16 kB aligned */ 1057 if (base == NULL) return; 1058 val=readl(base + 0x3418); /* read the Function Disable register, dword mode only */ 1059 writel(val & 0xFFFFFFF7, base + 0x3418); /* enable the SMBus device */ 1060 iounmap(base); 1061 printk(KERN_INFO "PCI: Enabled ICH6/i801 SMBus device\n"); 1062 } 1063 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6 ); 1064 1065 #endif 1066 1067 /* 1068 * SiS 96x south bridge: BIOS typically hides SMBus device... 1069 */ 1070 static void __init quirk_sis_96x_smbus(struct pci_dev *dev) 1071 { 1072 u8 val = 0; 1073 printk(KERN_INFO "Enabling SiS 96x SMBus.\n"); 1074 pci_read_config_byte(dev, 0x77, &val); 1075 pci_write_config_byte(dev, 0x77, val & ~0x10); 1076 pci_read_config_byte(dev, 0x77, &val); 1077 } 1078 1079 /* 1080 * ... This is further complicated by the fact that some SiS96x south 1081 * bridges pretend to be 85C503/5513 instead. In that case see if we 1082 * spotted a compatible north bridge to make sure. 1083 * (pci_find_device doesn't work yet) 1084 * 1085 * We can also enable the sis96x bit in the discovery register.. 1086 */ 1087 static int __devinitdata sis_96x_compatible = 0; 1088 1089 #define SIS_DETECT_REGISTER 0x40 1090 1091 static void __init quirk_sis_503(struct pci_dev *dev) 1092 { 1093 u8 reg; 1094 u16 devid; 1095 1096 pci_read_config_byte(dev, SIS_DETECT_REGISTER, ®); 1097 pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg | (1 << 6)); 1098 pci_read_config_word(dev, PCI_DEVICE_ID, &devid); 1099 if (((devid & 0xfff0) != 0x0960) && (devid != 0x0018)) { 1100 pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg); 1101 return; 1102 } 1103 1104 /* Make people aware that we changed the config.. */ 1105 printk(KERN_WARNING "Uncovering SIS%x that hid as a SIS503 (compatible=%d)\n", devid, sis_96x_compatible); 1106 1107 /* 1108 * Ok, it now shows up as a 96x.. The 96x quirks are after 1109 * the 503 quirk in the quirk table, so they'll automatically 1110 * run and enable things like the SMBus device 1111 */ 1112 dev->device = devid; 1113 } 1114 1115 static void __init quirk_sis_96x_compatible(struct pci_dev *dev) 1116 { 1117 sis_96x_compatible = 1; 1118 } 1119 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_645, quirk_sis_96x_compatible ); 1120 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_646, quirk_sis_96x_compatible ); 1121 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_648, quirk_sis_96x_compatible ); 1122 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_650, quirk_sis_96x_compatible ); 1123 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_651, quirk_sis_96x_compatible ); 1124 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_735, quirk_sis_96x_compatible ); 1125 1126 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503 ); 1127 /* 1128 * On ASUS A8V and A8V Deluxe boards, the onboard AC97 audio controller 1129 * and MC97 modem controller are disabled when a second PCI soundcard is 1130 * present. This patch, tweaking the VT8237 ISA bridge, enables them. 1131 * -- bjd 1132 */ 1133 static void __init asus_hides_ac97_lpc(struct pci_dev *dev) 1134 { 1135 u8 val; 1136 int asus_hides_ac97 = 0; 1137 1138 if (likely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) { 1139 if (dev->device == PCI_DEVICE_ID_VIA_8237) 1140 asus_hides_ac97 = 1; 1141 } 1142 1143 if (!asus_hides_ac97) 1144 return; 1145 1146 pci_read_config_byte(dev, 0x50, &val); 1147 if (val & 0xc0) { 1148 pci_write_config_byte(dev, 0x50, val & (~0xc0)); 1149 pci_read_config_byte(dev, 0x50, &val); 1150 if (val & 0xc0) 1151 printk(KERN_INFO "PCI: onboard AC97/MC97 devices continue to play 'hide and seek'! 0x%x\n", val); 1152 else 1153 printk(KERN_INFO "PCI: enabled onboard AC97/MC97 devices\n"); 1154 } 1155 } 1156 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, asus_hides_ac97_lpc ); 1157 1158 1159 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus ); 1160 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus ); 1161 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus ); 1162 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus ); 1163 1164 #ifdef CONFIG_X86_IO_APIC 1165 static void __init quirk_alder_ioapic(struct pci_dev *pdev) 1166 { 1167 int i; 1168 1169 if ((pdev->class >> 8) != 0xff00) 1170 return; 1171 1172 /* the first BAR is the location of the IO APIC...we must 1173 * not touch this (and it's already covered by the fixmap), so 1174 * forcibly insert it into the resource tree */ 1175 if (pci_resource_start(pdev, 0) && pci_resource_len(pdev, 0)) 1176 insert_resource(&iomem_resource, &pdev->resource[0]); 1177 1178 /* The next five BARs all seem to be rubbish, so just clean 1179 * them out */ 1180 for (i=1; i < 6; i++) { 1181 memset(&pdev->resource[i], 0, sizeof(pdev->resource[i])); 1182 } 1183 1184 } 1185 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EESSC, quirk_alder_ioapic ); 1186 #endif 1187 1188 enum ide_combined_type { COMBINED = 0, IDE = 1, LIBATA = 2 }; 1189 /* Defaults to combined */ 1190 static enum ide_combined_type combined_mode; 1191 1192 static int __init combined_setup(char *str) 1193 { 1194 if (!strncmp(str, "ide", 3)) 1195 combined_mode = IDE; 1196 else if (!strncmp(str, "libata", 6)) 1197 combined_mode = LIBATA; 1198 else /* "combined" or anything else defaults to old behavior */ 1199 combined_mode = COMBINED; 1200 1201 return 1; 1202 } 1203 __setup("combined_mode=", combined_setup); 1204 1205 #ifdef CONFIG_SCSI_SATA_INTEL_COMBINED 1206 static void __devinit quirk_intel_ide_combined(struct pci_dev *pdev) 1207 { 1208 u8 prog, comb, tmp; 1209 int ich = 0; 1210 1211 /* 1212 * Narrow down to Intel SATA PCI devices. 1213 */ 1214 switch (pdev->device) { 1215 /* PCI ids taken from drivers/scsi/ata_piix.c */ 1216 case 0x24d1: 1217 case 0x24df: 1218 case 0x25a3: 1219 case 0x25b0: 1220 ich = 5; 1221 break; 1222 case 0x2651: 1223 case 0x2652: 1224 case 0x2653: 1225 case 0x2680: /* ESB2 */ 1226 ich = 6; 1227 break; 1228 case 0x27c0: 1229 case 0x27c4: 1230 ich = 7; 1231 break; 1232 case 0x2828: /* ICH8M */ 1233 ich = 8; 1234 break; 1235 default: 1236 /* we do not handle this PCI device */ 1237 return; 1238 } 1239 1240 /* 1241 * Read combined mode register. 1242 */ 1243 pci_read_config_byte(pdev, 0x90, &tmp); /* combined mode reg */ 1244 1245 if (ich == 5) { 1246 tmp &= 0x6; /* interesting bits 2:1, PATA primary/secondary */ 1247 if (tmp == 0x4) /* bits 10x */ 1248 comb = (1 << 0); /* SATA port 0, PATA port 1 */ 1249 else if (tmp == 0x6) /* bits 11x */ 1250 comb = (1 << 2); /* PATA port 0, SATA port 1 */ 1251 else 1252 return; /* not in combined mode */ 1253 } else { 1254 WARN_ON((ich != 6) && (ich != 7) && (ich != 8)); 1255 tmp &= 0x3; /* interesting bits 1:0 */ 1256 if (tmp & (1 << 0)) 1257 comb = (1 << 2); /* PATA port 0, SATA port 1 */ 1258 else if (tmp & (1 << 1)) 1259 comb = (1 << 0); /* SATA port 0, PATA port 1 */ 1260 else 1261 return; /* not in combined mode */ 1262 } 1263 1264 /* 1265 * Read programming interface register. 1266 * (Tells us if it's legacy or native mode) 1267 */ 1268 pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); 1269 1270 /* if SATA port is in native mode, we're ok. */ 1271 if (prog & comb) 1272 return; 1273 1274 /* Don't reserve any so the IDE driver can get them (but only if 1275 * combined_mode=ide). 1276 */ 1277 if (combined_mode == IDE) 1278 return; 1279 1280 /* Grab them both for libata if combined_mode=libata. */ 1281 if (combined_mode == LIBATA) { 1282 request_region(0x1f0, 8, "libata"); /* port 0 */ 1283 request_region(0x170, 8, "libata"); /* port 1 */ 1284 return; 1285 } 1286 1287 /* SATA port is in legacy mode. Reserve port so that 1288 * IDE driver does not attempt to use it. If request_region 1289 * fails, it will be obvious at boot time, so we don't bother 1290 * checking return values. 1291 */ 1292 if (comb == (1 << 0)) 1293 request_region(0x1f0, 8, "libata"); /* port 0 */ 1294 else 1295 request_region(0x170, 8, "libata"); /* port 1 */ 1296 } 1297 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, quirk_intel_ide_combined ); 1298 #endif /* CONFIG_SCSI_SATA_INTEL_COMBINED */ 1299 1300 1301 int pcie_mch_quirk; 1302 1303 static void __devinit quirk_pcie_mch(struct pci_dev *pdev) 1304 { 1305 pcie_mch_quirk = 1; 1306 } 1307 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, quirk_pcie_mch ); 1308 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7320_MCH, quirk_pcie_mch ); 1309 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7525_MCH, quirk_pcie_mch ); 1310 1311 1312 /* 1313 * It's possible for the MSI to get corrupted if shpc and acpi 1314 * are used together on certain PXH-based systems. 1315 */ 1316 static void __devinit quirk_pcie_pxh(struct pci_dev *dev) 1317 { 1318 disable_msi_mode(dev, pci_find_capability(dev, PCI_CAP_ID_MSI), 1319 PCI_CAP_ID_MSI); 1320 dev->no_msi = 1; 1321 1322 printk(KERN_WARNING "PCI: PXH quirk detected, " 1323 "disabling MSI for SHPC device\n"); 1324 } 1325 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_0, quirk_pcie_pxh); 1326 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_1, quirk_pcie_pxh); 1327 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_pcie_pxh); 1328 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_pcie_pxh); 1329 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_pcie_pxh); 1330 1331 1332 /* 1333 * Fixup the cardbus bridges on the IBM Dock II docking station 1334 */ 1335 static void __devinit quirk_ibm_dock2_cardbus(struct pci_dev *dev) 1336 { 1337 u32 val; 1338 1339 /* 1340 * tie the 2 interrupt pins to INTA, and configure the 1341 * multifunction routing register to handle this. 1342 */ 1343 if ((dev->subsystem_vendor == PCI_VENDOR_ID_IBM) && 1344 (dev->subsystem_device == 0x0148)) { 1345 printk(KERN_INFO "PCI: Found IBM Dock II Cardbus Bridge " 1346 "applying quirk\n"); 1347 pci_read_config_dword(dev, 0x8c, &val); 1348 val = ((val & 0xffffff00) | 0x1002); 1349 pci_write_config_dword(dev, 0x8c, val); 1350 pci_read_config_dword(dev, 0x80, &val); 1351 val = ((val & 0x00ffff00) | 0x2864c077); 1352 pci_write_config_dword(dev, 0x80, val); 1353 } 1354 } 1355 1356 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_1420, 1357 quirk_ibm_dock2_cardbus); 1358 1359 static void __devinit quirk_netmos(struct pci_dev *dev) 1360 { 1361 unsigned int num_parallel = (dev->subsystem_device & 0xf0) >> 4; 1362 unsigned int num_serial = dev->subsystem_device & 0xf; 1363 1364 /* 1365 * These Netmos parts are multiport serial devices with optional 1366 * parallel ports. Even when parallel ports are present, they 1367 * are identified as class SERIAL, which means the serial driver 1368 * will claim them. To prevent this, mark them as class OTHER. 1369 * These combo devices should be claimed by parport_serial. 1370 * 1371 * The subdevice ID is of the form 0x00PS, where <P> is the number 1372 * of parallel ports and <S> is the number of serial ports. 1373 */ 1374 switch (dev->device) { 1375 case PCI_DEVICE_ID_NETMOS_9735: 1376 case PCI_DEVICE_ID_NETMOS_9745: 1377 case PCI_DEVICE_ID_NETMOS_9835: 1378 case PCI_DEVICE_ID_NETMOS_9845: 1379 case PCI_DEVICE_ID_NETMOS_9855: 1380 if ((dev->class >> 8) == PCI_CLASS_COMMUNICATION_SERIAL && 1381 num_parallel) { 1382 printk(KERN_INFO "PCI: Netmos %04x (%u parallel, " 1383 "%u serial); changing class SERIAL to OTHER " 1384 "(use parport_serial)\n", 1385 dev->device, num_parallel, num_serial); 1386 dev->class = (PCI_CLASS_COMMUNICATION_OTHER << 8) | 1387 (dev->class & 0xff); 1388 } 1389 } 1390 } 1391 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETMOS, PCI_ANY_ID, quirk_netmos); 1392 1393 1394 static void __devinit fixup_rev1_53c810(struct pci_dev* dev) 1395 { 1396 /* rev 1 ncr53c810 chips don't set the class at all which means 1397 * they don't get their resources remapped. Fix that here. 1398 */ 1399 1400 if (dev->class == PCI_CLASS_NOT_DEFINED) { 1401 printk(KERN_INFO "NCR 53c810 rev 1 detected, setting PCI class.\n"); 1402 dev->class = PCI_CLASS_STORAGE_SCSI; 1403 } 1404 } 1405 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810); 1406 1407 1408 static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, struct pci_fixup *end) 1409 { 1410 while (f < end) { 1411 if ((f->vendor == dev->vendor || f->vendor == (u16) PCI_ANY_ID) && 1412 (f->device == dev->device || f->device == (u16) PCI_ANY_ID)) { 1413 pr_debug("PCI: Calling quirk %p for %s\n", f->hook, pci_name(dev)); 1414 f->hook(dev); 1415 } 1416 f++; 1417 } 1418 } 1419 1420 extern struct pci_fixup __start_pci_fixups_early[]; 1421 extern struct pci_fixup __end_pci_fixups_early[]; 1422 extern struct pci_fixup __start_pci_fixups_header[]; 1423 extern struct pci_fixup __end_pci_fixups_header[]; 1424 extern struct pci_fixup __start_pci_fixups_final[]; 1425 extern struct pci_fixup __end_pci_fixups_final[]; 1426 extern struct pci_fixup __start_pci_fixups_enable[]; 1427 extern struct pci_fixup __end_pci_fixups_enable[]; 1428 1429 1430 void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev) 1431 { 1432 struct pci_fixup *start, *end; 1433 1434 switch(pass) { 1435 case pci_fixup_early: 1436 start = __start_pci_fixups_early; 1437 end = __end_pci_fixups_early; 1438 break; 1439 1440 case pci_fixup_header: 1441 start = __start_pci_fixups_header; 1442 end = __end_pci_fixups_header; 1443 break; 1444 1445 case pci_fixup_final: 1446 start = __start_pci_fixups_final; 1447 end = __end_pci_fixups_final; 1448 break; 1449 1450 case pci_fixup_enable: 1451 start = __start_pci_fixups_enable; 1452 end = __end_pci_fixups_enable; 1453 break; 1454 1455 default: 1456 /* stupid compiler warning, you would think with an enum... */ 1457 return; 1458 } 1459 pci_do_fixups(dev, start, end); 1460 } 1461 1462 /* Enable 1k I/O space granularity on the Intel P64H2 */ 1463 static void __devinit quirk_p64h2_1k_io(struct pci_dev *dev) 1464 { 1465 u16 en1k; 1466 u8 io_base_lo, io_limit_lo; 1467 unsigned long base, limit; 1468 struct resource *res = dev->resource + PCI_BRIDGE_RESOURCES; 1469 1470 pci_read_config_word(dev, 0x40, &en1k); 1471 1472 if (en1k & 0x200) { 1473 printk(KERN_INFO "PCI: Enable I/O Space to 1 KB Granularity\n"); 1474 1475 pci_read_config_byte(dev, PCI_IO_BASE, &io_base_lo); 1476 pci_read_config_byte(dev, PCI_IO_LIMIT, &io_limit_lo); 1477 base = (io_base_lo & (PCI_IO_RANGE_MASK | 0x0c)) << 8; 1478 limit = (io_limit_lo & (PCI_IO_RANGE_MASK | 0x0c)) << 8; 1479 1480 if (base <= limit) { 1481 res->start = base; 1482 res->end = limit + 0x3ff; 1483 } 1484 } 1485 } 1486 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x1460, quirk_p64h2_1k_io); 1487 1488 EXPORT_SYMBOL(pcie_mch_quirk); 1489 #ifdef CONFIG_HOTPLUG 1490 EXPORT_SYMBOL(pci_fixup_device); 1491 #endif 1492