1 /* 2 * This file contains work-arounds for many known PCI hardware 3 * bugs. Devices present only on certain architectures (host 4 * bridges et cetera) should be handled in arch-specific code. 5 * 6 * Note: any quirks for hotpluggable devices must _NOT_ be declared __init. 7 * 8 * Copyright (c) 1999 Martin Mares <mj@ucw.cz> 9 * 10 * Init/reset quirks for USB host controllers should be in the 11 * USB quirks file, where their drivers can access reuse it. 12 */ 13 14 #include <linux/types.h> 15 #include <linux/kernel.h> 16 #include <linux/export.h> 17 #include <linux/pci.h> 18 #include <linux/init.h> 19 #include <linux/delay.h> 20 #include <linux/acpi.h> 21 #include <linux/kallsyms.h> 22 #include <linux/dmi.h> 23 #include <linux/pci-aspm.h> 24 #include <linux/ioport.h> 25 #include <linux/sched.h> 26 #include <linux/ktime.h> 27 #include <linux/mm.h> 28 #include <asm/dma.h> /* isa_dma_bridge_buggy */ 29 #include "pci.h" 30 31 /* 32 * Decoding should be disabled for a PCI device during BAR sizing to avoid 33 * conflict. But doing so may cause problems on host bridge and perhaps other 34 * key system devices. For devices that need to have mmio decoding always-on, 35 * we need to set the dev->mmio_always_on bit. 36 */ 37 static void quirk_mmio_always_on(struct pci_dev *dev) 38 { 39 dev->mmio_always_on = 1; 40 } 41 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_ANY_ID, PCI_ANY_ID, 42 PCI_CLASS_BRIDGE_HOST, 8, quirk_mmio_always_on); 43 44 /* The Mellanox Tavor device gives false positive parity errors 45 * Mark this device with a broken_parity_status, to allow 46 * PCI scanning code to "skip" this now blacklisted device. 47 */ 48 static void quirk_mellanox_tavor(struct pci_dev *dev) 49 { 50 dev->broken_parity_status = 1; /* This device gives false positives */ 51 } 52 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_MELLANOX, PCI_DEVICE_ID_MELLANOX_TAVOR, quirk_mellanox_tavor); 53 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_MELLANOX, PCI_DEVICE_ID_MELLANOX_TAVOR_BRIDGE, quirk_mellanox_tavor); 54 55 /* Deal with broken BIOSes that neglect to enable passive release, 56 which can cause problems in combination with the 82441FX/PPro MTRRs */ 57 static void quirk_passive_release(struct pci_dev *dev) 58 { 59 struct pci_dev *d = NULL; 60 unsigned char dlc; 61 62 /* We have to make sure a particular bit is set in the PIIX3 63 ISA bridge, so we have to go out and find it. */ 64 while ((d = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, d))) { 65 pci_read_config_byte(d, 0x82, &dlc); 66 if (!(dlc & 1<<1)) { 67 dev_info(&d->dev, "PIIX3: Enabling Passive Release\n"); 68 dlc |= 1<<1; 69 pci_write_config_byte(d, 0x82, dlc); 70 } 71 } 72 } 73 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release); 74 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release); 75 76 /* The VIA VP2/VP3/MVP3 seem to have some 'features'. There may be a workaround 77 but VIA don't answer queries. If you happen to have good contacts at VIA 78 ask them for me please -- Alan 79 80 This appears to be BIOS not version dependent. So presumably there is a 81 chipset level fix */ 82 83 static void quirk_isa_dma_hangs(struct pci_dev *dev) 84 { 85 if (!isa_dma_bridge_buggy) { 86 isa_dma_bridge_buggy = 1; 87 dev_info(&dev->dev, "Activating ISA DMA hang workarounds\n"); 88 } 89 } 90 /* 91 * Its not totally clear which chipsets are the problematic ones 92 * We know 82C586 and 82C596 variants are affected. 93 */ 94 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_isa_dma_hangs); 95 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C596, quirk_isa_dma_hangs); 96 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, quirk_isa_dma_hangs); 97 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, quirk_isa_dma_hangs); 98 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_1, quirk_isa_dma_hangs); 99 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_2, quirk_isa_dma_hangs); 100 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_3, quirk_isa_dma_hangs); 101 102 /* 103 * Intel NM10 "TigerPoint" LPC PM1a_STS.BM_STS must be clear 104 * for some HT machines to use C4 w/o hanging. 105 */ 106 static void quirk_tigerpoint_bm_sts(struct pci_dev *dev) 107 { 108 u32 pmbase; 109 u16 pm1a; 110 111 pci_read_config_dword(dev, 0x40, &pmbase); 112 pmbase = pmbase & 0xff80; 113 pm1a = inw(pmbase); 114 115 if (pm1a & 0x10) { 116 dev_info(&dev->dev, FW_BUG "TigerPoint LPC.BM_STS cleared\n"); 117 outw(0x10, pmbase); 118 } 119 } 120 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_TGP_LPC, quirk_tigerpoint_bm_sts); 121 122 /* 123 * Chipsets where PCI->PCI transfers vanish or hang 124 */ 125 static void quirk_nopcipci(struct pci_dev *dev) 126 { 127 if ((pci_pci_problems & PCIPCI_FAIL) == 0) { 128 dev_info(&dev->dev, "Disabling direct PCI/PCI transfers\n"); 129 pci_pci_problems |= PCIPCI_FAIL; 130 } 131 } 132 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5597, quirk_nopcipci); 133 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_496, quirk_nopcipci); 134 135 static void quirk_nopciamd(struct pci_dev *dev) 136 { 137 u8 rev; 138 pci_read_config_byte(dev, 0x08, &rev); 139 if (rev == 0x13) { 140 /* Erratum 24 */ 141 dev_info(&dev->dev, "Chipset erratum: Disabling direct PCI/AGP transfers\n"); 142 pci_pci_problems |= PCIAGP_FAIL; 143 } 144 } 145 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8151_0, quirk_nopciamd); 146 147 /* 148 * Triton requires workarounds to be used by the drivers 149 */ 150 static void quirk_triton(struct pci_dev *dev) 151 { 152 if ((pci_pci_problems&PCIPCI_TRITON) == 0) { 153 dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n"); 154 pci_pci_problems |= PCIPCI_TRITON; 155 } 156 } 157 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437, quirk_triton); 158 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437VX, quirk_triton); 159 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439, quirk_triton); 160 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439TX, quirk_triton); 161 162 /* 163 * VIA Apollo KT133 needs PCI latency patch 164 * Made according to a windows driver based patch by George E. Breese 165 * see PCI Latency Adjust on http://www.viahardware.com/download/viatweak.shtm 166 * Also see http://www.au-ja.org/review-kt133a-1-en.phtml for 167 * the info on which Mr Breese based his work. 168 * 169 * Updated based on further information from the site and also on 170 * information provided by VIA 171 */ 172 static void quirk_vialatency(struct pci_dev *dev) 173 { 174 struct pci_dev *p; 175 u8 busarb; 176 /* Ok we have a potential problem chipset here. Now see if we have 177 a buggy southbridge */ 178 179 p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, NULL); 180 if (p != NULL) { 181 /* 0x40 - 0x4f == 686B, 0x10 - 0x2f == 686A; thanks Dan Hollis */ 182 /* Check for buggy part revisions */ 183 if (p->revision < 0x40 || p->revision > 0x42) 184 goto exit; 185 } else { 186 p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, NULL); 187 if (p == NULL) /* No problem parts */ 188 goto exit; 189 /* Check for buggy part revisions */ 190 if (p->revision < 0x10 || p->revision > 0x12) 191 goto exit; 192 } 193 194 /* 195 * Ok we have the problem. Now set the PCI master grant to 196 * occur every master grant. The apparent bug is that under high 197 * PCI load (quite common in Linux of course) you can get data 198 * loss when the CPU is held off the bus for 3 bus master requests 199 * This happens to include the IDE controllers.... 200 * 201 * VIA only apply this fix when an SB Live! is present but under 202 * both Linux and Windows this isn't enough, and we have seen 203 * corruption without SB Live! but with things like 3 UDMA IDE 204 * controllers. So we ignore that bit of the VIA recommendation.. 205 */ 206 207 pci_read_config_byte(dev, 0x76, &busarb); 208 /* Set bit 4 and bi 5 of byte 76 to 0x01 209 "Master priority rotation on every PCI master grant */ 210 busarb &= ~(1<<5); 211 busarb |= (1<<4); 212 pci_write_config_byte(dev, 0x76, busarb); 213 dev_info(&dev->dev, "Applying VIA southbridge workaround\n"); 214 exit: 215 pci_dev_put(p); 216 } 217 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency); 218 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency); 219 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency); 220 /* Must restore this on a resume from RAM */ 221 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency); 222 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency); 223 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency); 224 225 /* 226 * VIA Apollo VP3 needs ETBF on BT848/878 227 */ 228 static void quirk_viaetbf(struct pci_dev *dev) 229 { 230 if ((pci_pci_problems&PCIPCI_VIAETBF) == 0) { 231 dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n"); 232 pci_pci_problems |= PCIPCI_VIAETBF; 233 } 234 } 235 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_viaetbf); 236 237 static void quirk_vsfx(struct pci_dev *dev) 238 { 239 if ((pci_pci_problems&PCIPCI_VSFX) == 0) { 240 dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n"); 241 pci_pci_problems |= PCIPCI_VSFX; 242 } 243 } 244 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C576, quirk_vsfx); 245 246 /* 247 * Ali Magik requires workarounds to be used by the drivers 248 * that DMA to AGP space. Latency must be set to 0xA and triton 249 * workaround applied too 250 * [Info kindly provided by ALi] 251 */ 252 static void quirk_alimagik(struct pci_dev *dev) 253 { 254 if ((pci_pci_problems&PCIPCI_ALIMAGIK) == 0) { 255 dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n"); 256 pci_pci_problems |= PCIPCI_ALIMAGIK|PCIPCI_TRITON; 257 } 258 } 259 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1647, quirk_alimagik); 260 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1651, quirk_alimagik); 261 262 /* 263 * Natoma has some interesting boundary conditions with Zoran stuff 264 * at least 265 */ 266 static void quirk_natoma(struct pci_dev *dev) 267 { 268 if ((pci_pci_problems&PCIPCI_NATOMA) == 0) { 269 dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n"); 270 pci_pci_problems |= PCIPCI_NATOMA; 271 } 272 } 273 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_natoma); 274 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_0, quirk_natoma); 275 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_1, quirk_natoma); 276 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_0, quirk_natoma); 277 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_1, quirk_natoma); 278 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_2, quirk_natoma); 279 280 /* 281 * This chip can cause PCI parity errors if config register 0xA0 is read 282 * while DMAs are occurring. 283 */ 284 static void quirk_citrine(struct pci_dev *dev) 285 { 286 dev->cfg_size = 0xA0; 287 } 288 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, PCI_DEVICE_ID_IBM_CITRINE, quirk_citrine); 289 290 /* 291 * This chip can cause bus lockups if config addresses above 0x600 292 * are read or written. 293 */ 294 static void quirk_nfp6000(struct pci_dev *dev) 295 { 296 dev->cfg_size = 0x600; 297 } 298 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETRONOME, PCI_DEVICE_ID_NETRONOME_NFP4000, quirk_nfp6000); 299 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETRONOME, PCI_DEVICE_ID_NETRONOME_NFP6000, quirk_nfp6000); 300 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETRONOME, PCI_DEVICE_ID_NETRONOME_NFP6000_VF, quirk_nfp6000); 301 302 /* On IBM Crocodile ipr SAS adapters, expand BAR to system page size */ 303 static void quirk_extend_bar_to_page(struct pci_dev *dev) 304 { 305 int i; 306 307 for (i = 0; i < PCI_STD_RESOURCE_END; i++) { 308 struct resource *r = &dev->resource[i]; 309 310 if (r->flags & IORESOURCE_MEM && resource_size(r) < PAGE_SIZE) { 311 r->end = PAGE_SIZE - 1; 312 r->start = 0; 313 r->flags |= IORESOURCE_UNSET; 314 dev_info(&dev->dev, "expanded BAR %d to page size: %pR\n", 315 i, r); 316 } 317 } 318 } 319 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, 0x034a, quirk_extend_bar_to_page); 320 321 /* 322 * S3 868 and 968 chips report region size equal to 32M, but they decode 64M. 323 * If it's needed, re-allocate the region. 324 */ 325 static void quirk_s3_64M(struct pci_dev *dev) 326 { 327 struct resource *r = &dev->resource[0]; 328 329 if ((r->start & 0x3ffffff) || r->end != r->start + 0x3ffffff) { 330 r->flags |= IORESOURCE_UNSET; 331 r->start = 0; 332 r->end = 0x3ffffff; 333 } 334 } 335 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_868, quirk_s3_64M); 336 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_968, quirk_s3_64M); 337 338 static void quirk_io(struct pci_dev *dev, int pos, unsigned size, 339 const char *name) 340 { 341 u32 region; 342 struct pci_bus_region bus_region; 343 struct resource *res = dev->resource + pos; 344 345 pci_read_config_dword(dev, PCI_BASE_ADDRESS_0 + (pos << 2), ®ion); 346 347 if (!region) 348 return; 349 350 res->name = pci_name(dev); 351 res->flags = region & ~PCI_BASE_ADDRESS_IO_MASK; 352 res->flags |= 353 (IORESOURCE_IO | IORESOURCE_PCI_FIXED | IORESOURCE_SIZEALIGN); 354 region &= ~(size - 1); 355 356 /* Convert from PCI bus to resource space */ 357 bus_region.start = region; 358 bus_region.end = region + size - 1; 359 pcibios_bus_to_resource(dev->bus, res, &bus_region); 360 361 dev_info(&dev->dev, FW_BUG "%s quirk: reg 0x%x: %pR\n", 362 name, PCI_BASE_ADDRESS_0 + (pos << 2), res); 363 } 364 365 /* 366 * Some CS5536 BIOSes (for example, the Soekris NET5501 board w/ comBIOS 367 * ver. 1.33 20070103) don't set the correct ISA PCI region header info. 368 * BAR0 should be 8 bytes; instead, it may be set to something like 8k 369 * (which conflicts w/ BAR1's memory range). 370 * 371 * CS553x's ISA PCI BARs may also be read-only (ref: 372 * https://bugzilla.kernel.org/show_bug.cgi?id=85991 - Comment #4 forward). 373 */ 374 static void quirk_cs5536_vsa(struct pci_dev *dev) 375 { 376 static char *name = "CS5536 ISA bridge"; 377 378 if (pci_resource_len(dev, 0) != 8) { 379 quirk_io(dev, 0, 8, name); /* SMB */ 380 quirk_io(dev, 1, 256, name); /* GPIO */ 381 quirk_io(dev, 2, 64, name); /* MFGPT */ 382 dev_info(&dev->dev, "%s bug detected (incorrect header); workaround applied\n", 383 name); 384 } 385 } 386 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, quirk_cs5536_vsa); 387 388 static void quirk_io_region(struct pci_dev *dev, int port, 389 unsigned size, int nr, const char *name) 390 { 391 u16 region; 392 struct pci_bus_region bus_region; 393 struct resource *res = dev->resource + nr; 394 395 pci_read_config_word(dev, port, ®ion); 396 region &= ~(size - 1); 397 398 if (!region) 399 return; 400 401 res->name = pci_name(dev); 402 res->flags = IORESOURCE_IO; 403 404 /* Convert from PCI bus to resource space */ 405 bus_region.start = region; 406 bus_region.end = region + size - 1; 407 pcibios_bus_to_resource(dev->bus, res, &bus_region); 408 409 if (!pci_claim_resource(dev, nr)) 410 dev_info(&dev->dev, "quirk: %pR claimed by %s\n", res, name); 411 } 412 413 /* 414 * ATI Northbridge setups MCE the processor if you even 415 * read somewhere between 0x3b0->0x3bb or read 0x3d3 416 */ 417 static void quirk_ati_exploding_mce(struct pci_dev *dev) 418 { 419 dev_info(&dev->dev, "ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb\n"); 420 /* Mae rhaid i ni beidio ag edrych ar y lleoliadiau I/O hyn */ 421 request_region(0x3b0, 0x0C, "RadeonIGP"); 422 request_region(0x3d3, 0x01, "RadeonIGP"); 423 } 424 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS100, quirk_ati_exploding_mce); 425 426 /* 427 * In the AMD NL platform, this device ([1022:7912]) has a class code of 428 * PCI_CLASS_SERIAL_USB_XHCI (0x0c0330), which means the xhci driver will 429 * claim it. 430 * But the dwc3 driver is a more specific driver for this device, and we'd 431 * prefer to use it instead of xhci. To prevent xhci from claiming the 432 * device, change the class code to 0x0c03fe, which the PCI r3.0 spec 433 * defines as "USB device (not host controller)". The dwc3 driver can then 434 * claim it based on its Vendor and Device ID. 435 */ 436 static void quirk_amd_nl_class(struct pci_dev *pdev) 437 { 438 u32 class = pdev->class; 439 440 /* Use "USB Device (not host controller)" class */ 441 pdev->class = PCI_CLASS_SERIAL_USB_DEVICE; 442 dev_info(&pdev->dev, "PCI class overridden (%#08x -> %#08x) so dwc3 driver can claim this instead of xhci\n", 443 class, pdev->class); 444 } 445 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_NL_USB, 446 quirk_amd_nl_class); 447 448 /* 449 * Let's make the southbridge information explicit instead 450 * of having to worry about people probing the ACPI areas, 451 * for example.. (Yes, it happens, and if you read the wrong 452 * ACPI register it will put the machine to sleep with no 453 * way of waking it up again. Bummer). 454 * 455 * ALI M7101: Two IO regions pointed to by words at 456 * 0xE0 (64 bytes of ACPI registers) 457 * 0xE2 (32 bytes of SMB registers) 458 */ 459 static void quirk_ali7101_acpi(struct pci_dev *dev) 460 { 461 quirk_io_region(dev, 0xE0, 64, PCI_BRIDGE_RESOURCES, "ali7101 ACPI"); 462 quirk_io_region(dev, 0xE2, 32, PCI_BRIDGE_RESOURCES+1, "ali7101 SMB"); 463 } 464 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101, quirk_ali7101_acpi); 465 466 static void piix4_io_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable) 467 { 468 u32 devres; 469 u32 mask, size, base; 470 471 pci_read_config_dword(dev, port, &devres); 472 if ((devres & enable) != enable) 473 return; 474 mask = (devres >> 16) & 15; 475 base = devres & 0xffff; 476 size = 16; 477 for (;;) { 478 unsigned bit = size >> 1; 479 if ((bit & mask) == bit) 480 break; 481 size = bit; 482 } 483 /* 484 * For now we only print it out. Eventually we'll want to 485 * reserve it (at least if it's in the 0x1000+ range), but 486 * let's get enough confirmation reports first. 487 */ 488 base &= -size; 489 dev_info(&dev->dev, "%s PIO at %04x-%04x\n", name, base, 490 base + size - 1); 491 } 492 493 static void piix4_mem_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable) 494 { 495 u32 devres; 496 u32 mask, size, base; 497 498 pci_read_config_dword(dev, port, &devres); 499 if ((devres & enable) != enable) 500 return; 501 base = devres & 0xffff0000; 502 mask = (devres & 0x3f) << 16; 503 size = 128 << 16; 504 for (;;) { 505 unsigned bit = size >> 1; 506 if ((bit & mask) == bit) 507 break; 508 size = bit; 509 } 510 /* 511 * For now we only print it out. Eventually we'll want to 512 * reserve it, but let's get enough confirmation reports first. 513 */ 514 base &= -size; 515 dev_info(&dev->dev, "%s MMIO at %04x-%04x\n", name, base, 516 base + size - 1); 517 } 518 519 /* 520 * PIIX4 ACPI: Two IO regions pointed to by longwords at 521 * 0x40 (64 bytes of ACPI registers) 522 * 0x90 (16 bytes of SMB registers) 523 * and a few strange programmable PIIX4 device resources. 524 */ 525 static void quirk_piix4_acpi(struct pci_dev *dev) 526 { 527 u32 res_a; 528 529 quirk_io_region(dev, 0x40, 64, PCI_BRIDGE_RESOURCES, "PIIX4 ACPI"); 530 quirk_io_region(dev, 0x90, 16, PCI_BRIDGE_RESOURCES+1, "PIIX4 SMB"); 531 532 /* Device resource A has enables for some of the other ones */ 533 pci_read_config_dword(dev, 0x5c, &res_a); 534 535 piix4_io_quirk(dev, "PIIX4 devres B", 0x60, 3 << 21); 536 piix4_io_quirk(dev, "PIIX4 devres C", 0x64, 3 << 21); 537 538 /* Device resource D is just bitfields for static resources */ 539 540 /* Device 12 enabled? */ 541 if (res_a & (1 << 29)) { 542 piix4_io_quirk(dev, "PIIX4 devres E", 0x68, 1 << 20); 543 piix4_mem_quirk(dev, "PIIX4 devres F", 0x6c, 1 << 7); 544 } 545 /* Device 13 enabled? */ 546 if (res_a & (1 << 30)) { 547 piix4_io_quirk(dev, "PIIX4 devres G", 0x70, 1 << 20); 548 piix4_mem_quirk(dev, "PIIX4 devres H", 0x74, 1 << 7); 549 } 550 piix4_io_quirk(dev, "PIIX4 devres I", 0x78, 1 << 20); 551 piix4_io_quirk(dev, "PIIX4 devres J", 0x7c, 1 << 20); 552 } 553 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, quirk_piix4_acpi); 554 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443MX_3, quirk_piix4_acpi); 555 556 #define ICH_PMBASE 0x40 557 #define ICH_ACPI_CNTL 0x44 558 #define ICH4_ACPI_EN 0x10 559 #define ICH6_ACPI_EN 0x80 560 #define ICH4_GPIOBASE 0x58 561 #define ICH4_GPIO_CNTL 0x5c 562 #define ICH4_GPIO_EN 0x10 563 #define ICH6_GPIOBASE 0x48 564 #define ICH6_GPIO_CNTL 0x4c 565 #define ICH6_GPIO_EN 0x10 566 567 /* 568 * ICH4, ICH4-M, ICH5, ICH5-M ACPI: Three IO regions pointed to by longwords at 569 * 0x40 (128 bytes of ACPI, GPIO & TCO registers) 570 * 0x58 (64 bytes of GPIO I/O space) 571 */ 572 static void quirk_ich4_lpc_acpi(struct pci_dev *dev) 573 { 574 u8 enable; 575 576 /* 577 * The check for PCIBIOS_MIN_IO is to ensure we won't create a conflict 578 * with low legacy (and fixed) ports. We don't know the decoding 579 * priority and can't tell whether the legacy device or the one created 580 * here is really at that address. This happens on boards with broken 581 * BIOSes. 582 */ 583 584 pci_read_config_byte(dev, ICH_ACPI_CNTL, &enable); 585 if (enable & ICH4_ACPI_EN) 586 quirk_io_region(dev, ICH_PMBASE, 128, PCI_BRIDGE_RESOURCES, 587 "ICH4 ACPI/GPIO/TCO"); 588 589 pci_read_config_byte(dev, ICH4_GPIO_CNTL, &enable); 590 if (enable & ICH4_GPIO_EN) 591 quirk_io_region(dev, ICH4_GPIOBASE, 64, PCI_BRIDGE_RESOURCES+1, 592 "ICH4 GPIO"); 593 } 594 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, quirk_ich4_lpc_acpi); 595 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_0, quirk_ich4_lpc_acpi); 596 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, quirk_ich4_lpc_acpi); 597 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_10, quirk_ich4_lpc_acpi); 598 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, quirk_ich4_lpc_acpi); 599 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, quirk_ich4_lpc_acpi); 600 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, quirk_ich4_lpc_acpi); 601 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, quirk_ich4_lpc_acpi); 602 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, quirk_ich4_lpc_acpi); 603 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_1, quirk_ich4_lpc_acpi); 604 605 static void ich6_lpc_acpi_gpio(struct pci_dev *dev) 606 { 607 u8 enable; 608 609 pci_read_config_byte(dev, ICH_ACPI_CNTL, &enable); 610 if (enable & ICH6_ACPI_EN) 611 quirk_io_region(dev, ICH_PMBASE, 128, PCI_BRIDGE_RESOURCES, 612 "ICH6 ACPI/GPIO/TCO"); 613 614 pci_read_config_byte(dev, ICH6_GPIO_CNTL, &enable); 615 if (enable & ICH6_GPIO_EN) 616 quirk_io_region(dev, ICH6_GPIOBASE, 64, PCI_BRIDGE_RESOURCES+1, 617 "ICH6 GPIO"); 618 } 619 620 static void ich6_lpc_generic_decode(struct pci_dev *dev, unsigned reg, const char *name, int dynsize) 621 { 622 u32 val; 623 u32 size, base; 624 625 pci_read_config_dword(dev, reg, &val); 626 627 /* Enabled? */ 628 if (!(val & 1)) 629 return; 630 base = val & 0xfffc; 631 if (dynsize) { 632 /* 633 * This is not correct. It is 16, 32 or 64 bytes depending on 634 * register D31:F0:ADh bits 5:4. 635 * 636 * But this gets us at least _part_ of it. 637 */ 638 size = 16; 639 } else { 640 size = 128; 641 } 642 base &= ~(size-1); 643 644 /* Just print it out for now. We should reserve it after more debugging */ 645 dev_info(&dev->dev, "%s PIO at %04x-%04x\n", name, base, base+size-1); 646 } 647 648 static void quirk_ich6_lpc(struct pci_dev *dev) 649 { 650 /* Shared ACPI/GPIO decode with all ICH6+ */ 651 ich6_lpc_acpi_gpio(dev); 652 653 /* ICH6-specific generic IO decode */ 654 ich6_lpc_generic_decode(dev, 0x84, "LPC Generic IO decode 1", 0); 655 ich6_lpc_generic_decode(dev, 0x88, "LPC Generic IO decode 2", 1); 656 } 657 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_0, quirk_ich6_lpc); 658 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, quirk_ich6_lpc); 659 660 static void ich7_lpc_generic_decode(struct pci_dev *dev, unsigned reg, const char *name) 661 { 662 u32 val; 663 u32 mask, base; 664 665 pci_read_config_dword(dev, reg, &val); 666 667 /* Enabled? */ 668 if (!(val & 1)) 669 return; 670 671 /* 672 * IO base in bits 15:2, mask in bits 23:18, both 673 * are dword-based 674 */ 675 base = val & 0xfffc; 676 mask = (val >> 16) & 0xfc; 677 mask |= 3; 678 679 /* Just print it out for now. We should reserve it after more debugging */ 680 dev_info(&dev->dev, "%s PIO at %04x (mask %04x)\n", name, base, mask); 681 } 682 683 /* ICH7-10 has the same common LPC generic IO decode registers */ 684 static void quirk_ich7_lpc(struct pci_dev *dev) 685 { 686 /* We share the common ACPI/GPIO decode with ICH6 */ 687 ich6_lpc_acpi_gpio(dev); 688 689 /* And have 4 ICH7+ generic decodes */ 690 ich7_lpc_generic_decode(dev, 0x84, "ICH7 LPC Generic IO decode 1"); 691 ich7_lpc_generic_decode(dev, 0x88, "ICH7 LPC Generic IO decode 2"); 692 ich7_lpc_generic_decode(dev, 0x8c, "ICH7 LPC Generic IO decode 3"); 693 ich7_lpc_generic_decode(dev, 0x90, "ICH7 LPC Generic IO decode 4"); 694 } 695 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_0, quirk_ich7_lpc); 696 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_1, quirk_ich7_lpc); 697 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_31, quirk_ich7_lpc); 698 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_0, quirk_ich7_lpc); 699 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_2, quirk_ich7_lpc); 700 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_3, quirk_ich7_lpc); 701 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_1, quirk_ich7_lpc); 702 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_4, quirk_ich7_lpc); 703 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_2, quirk_ich7_lpc); 704 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_4, quirk_ich7_lpc); 705 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_7, quirk_ich7_lpc); 706 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_8, quirk_ich7_lpc); 707 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH10_1, quirk_ich7_lpc); 708 709 /* 710 * VIA ACPI: One IO region pointed to by longword at 711 * 0x48 or 0x20 (256 bytes of ACPI registers) 712 */ 713 static void quirk_vt82c586_acpi(struct pci_dev *dev) 714 { 715 if (dev->revision & 0x10) 716 quirk_io_region(dev, 0x48, 256, PCI_BRIDGE_RESOURCES, 717 "vt82c586 ACPI"); 718 } 719 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_vt82c586_acpi); 720 721 /* 722 * VIA VT82C686 ACPI: Three IO region pointed to by (long)words at 723 * 0x48 (256 bytes of ACPI registers) 724 * 0x70 (128 bytes of hardware monitoring register) 725 * 0x90 (16 bytes of SMB registers) 726 */ 727 static void quirk_vt82c686_acpi(struct pci_dev *dev) 728 { 729 quirk_vt82c586_acpi(dev); 730 731 quirk_io_region(dev, 0x70, 128, PCI_BRIDGE_RESOURCES+1, 732 "vt82c686 HW-mon"); 733 734 quirk_io_region(dev, 0x90, 16, PCI_BRIDGE_RESOURCES+2, "vt82c686 SMB"); 735 } 736 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_vt82c686_acpi); 737 738 /* 739 * VIA VT8235 ISA Bridge: Two IO regions pointed to by words at 740 * 0x88 (128 bytes of power management registers) 741 * 0xd0 (16 bytes of SMB registers) 742 */ 743 static void quirk_vt8235_acpi(struct pci_dev *dev) 744 { 745 quirk_io_region(dev, 0x88, 128, PCI_BRIDGE_RESOURCES, "vt8235 PM"); 746 quirk_io_region(dev, 0xd0, 16, PCI_BRIDGE_RESOURCES+1, "vt8235 SMB"); 747 } 748 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_vt8235_acpi); 749 750 /* 751 * TI XIO2000a PCIe-PCI Bridge erroneously reports it supports fast back-to-back: 752 * Disable fast back-to-back on the secondary bus segment 753 */ 754 static void quirk_xio2000a(struct pci_dev *dev) 755 { 756 struct pci_dev *pdev; 757 u16 command; 758 759 dev_warn(&dev->dev, "TI XIO2000a quirk detected; secondary bus fast back-to-back transfers disabled\n"); 760 list_for_each_entry(pdev, &dev->subordinate->devices, bus_list) { 761 pci_read_config_word(pdev, PCI_COMMAND, &command); 762 if (command & PCI_COMMAND_FAST_BACK) 763 pci_write_config_word(pdev, PCI_COMMAND, command & ~PCI_COMMAND_FAST_BACK); 764 } 765 } 766 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_XIO2000A, 767 quirk_xio2000a); 768 769 #ifdef CONFIG_X86_IO_APIC 770 771 #include <asm/io_apic.h> 772 773 /* 774 * VIA 686A/B: If an IO-APIC is active, we need to route all on-chip 775 * devices to the external APIC. 776 * 777 * TODO: When we have device-specific interrupt routers, 778 * this code will go away from quirks. 779 */ 780 static void quirk_via_ioapic(struct pci_dev *dev) 781 { 782 u8 tmp; 783 784 if (nr_ioapics < 1) 785 tmp = 0; /* nothing routed to external APIC */ 786 else 787 tmp = 0x1f; /* all known bits (4-0) routed to external APIC */ 788 789 dev_info(&dev->dev, "%sbling VIA external APIC routing\n", 790 tmp == 0 ? "Disa" : "Ena"); 791 792 /* Offset 0x58: External APIC IRQ output control */ 793 pci_write_config_byte(dev, 0x58, tmp); 794 } 795 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic); 796 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic); 797 798 /* 799 * VIA 8237: Some BIOSes don't set the 'Bypass APIC De-Assert Message' Bit. 800 * This leads to doubled level interrupt rates. 801 * Set this bit to get rid of cycle wastage. 802 * Otherwise uncritical. 803 */ 804 static void quirk_via_vt8237_bypass_apic_deassert(struct pci_dev *dev) 805 { 806 u8 misc_control2; 807 #define BYPASS_APIC_DEASSERT 8 808 809 pci_read_config_byte(dev, 0x5B, &misc_control2); 810 if (!(misc_control2 & BYPASS_APIC_DEASSERT)) { 811 dev_info(&dev->dev, "Bypassing VIA 8237 APIC De-Assert Message\n"); 812 pci_write_config_byte(dev, 0x5B, misc_control2|BYPASS_APIC_DEASSERT); 813 } 814 } 815 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_vt8237_bypass_apic_deassert); 816 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_vt8237_bypass_apic_deassert); 817 818 /* 819 * The AMD io apic can hang the box when an apic irq is masked. 820 * We check all revs >= B0 (yet not in the pre production!) as the bug 821 * is currently marked NoFix 822 * 823 * We have multiple reports of hangs with this chipset that went away with 824 * noapic specified. For the moment we assume it's the erratum. We may be wrong 825 * of course. However the advice is demonstrably good even if so.. 826 */ 827 static void quirk_amd_ioapic(struct pci_dev *dev) 828 { 829 if (dev->revision >= 0x02) { 830 dev_warn(&dev->dev, "I/O APIC: AMD Erratum #22 may be present. In the event of instability try\n"); 831 dev_warn(&dev->dev, " : booting with the \"noapic\" option\n"); 832 } 833 } 834 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7410, quirk_amd_ioapic); 835 #endif /* CONFIG_X86_IO_APIC */ 836 837 /* 838 * Some settings of MMRBC can lead to data corruption so block changes. 839 * See AMD 8131 HyperTransport PCI-X Tunnel Revision Guide 840 */ 841 static void quirk_amd_8131_mmrbc(struct pci_dev *dev) 842 { 843 if (dev->subordinate && dev->revision <= 0x12) { 844 dev_info(&dev->dev, "AMD8131 rev %x detected; disabling PCI-X MMRBC\n", 845 dev->revision); 846 dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MMRBC; 847 } 848 } 849 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_amd_8131_mmrbc); 850 851 /* 852 * FIXME: it is questionable that quirk_via_acpi 853 * is needed. It shows up as an ISA bridge, and does not 854 * support the PCI_INTERRUPT_LINE register at all. Therefore 855 * it seems like setting the pci_dev's 'irq' to the 856 * value of the ACPI SCI interrupt is only done for convenience. 857 * -jgarzik 858 */ 859 static void quirk_via_acpi(struct pci_dev *d) 860 { 861 /* 862 * VIA ACPI device: SCI IRQ line in PCI config byte 0x42 863 */ 864 u8 irq; 865 pci_read_config_byte(d, 0x42, &irq); 866 irq &= 0xf; 867 if (irq && (irq != 2)) 868 d->irq = irq; 869 } 870 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_acpi); 871 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_acpi); 872 873 874 /* 875 * VIA bridges which have VLink 876 */ 877 878 static int via_vlink_dev_lo = -1, via_vlink_dev_hi = 18; 879 880 static void quirk_via_bridge(struct pci_dev *dev) 881 { 882 /* See what bridge we have and find the device ranges */ 883 switch (dev->device) { 884 case PCI_DEVICE_ID_VIA_82C686: 885 /* The VT82C686 is special, it attaches to PCI and can have 886 any device number. All its subdevices are functions of 887 that single device. */ 888 via_vlink_dev_lo = PCI_SLOT(dev->devfn); 889 via_vlink_dev_hi = PCI_SLOT(dev->devfn); 890 break; 891 case PCI_DEVICE_ID_VIA_8237: 892 case PCI_DEVICE_ID_VIA_8237A: 893 via_vlink_dev_lo = 15; 894 break; 895 case PCI_DEVICE_ID_VIA_8235: 896 via_vlink_dev_lo = 16; 897 break; 898 case PCI_DEVICE_ID_VIA_8231: 899 case PCI_DEVICE_ID_VIA_8233_0: 900 case PCI_DEVICE_ID_VIA_8233A: 901 case PCI_DEVICE_ID_VIA_8233C_0: 902 via_vlink_dev_lo = 17; 903 break; 904 } 905 } 906 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_bridge); 907 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, quirk_via_bridge); 908 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233_0, quirk_via_bridge); 909 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233A, quirk_via_bridge); 910 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233C_0, quirk_via_bridge); 911 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_via_bridge); 912 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_bridge); 913 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237A, quirk_via_bridge); 914 915 /** 916 * quirk_via_vlink - VIA VLink IRQ number update 917 * @dev: PCI device 918 * 919 * If the device we are dealing with is on a PIC IRQ we need to 920 * ensure that the IRQ line register which usually is not relevant 921 * for PCI cards, is actually written so that interrupts get sent 922 * to the right place. 923 * We only do this on systems where a VIA south bridge was detected, 924 * and only for VIA devices on the motherboard (see quirk_via_bridge 925 * above). 926 */ 927 928 static void quirk_via_vlink(struct pci_dev *dev) 929 { 930 u8 irq, new_irq; 931 932 /* Check if we have VLink at all */ 933 if (via_vlink_dev_lo == -1) 934 return; 935 936 new_irq = dev->irq; 937 938 /* Don't quirk interrupts outside the legacy IRQ range */ 939 if (!new_irq || new_irq > 15) 940 return; 941 942 /* Internal device ? */ 943 if (dev->bus->number != 0 || PCI_SLOT(dev->devfn) > via_vlink_dev_hi || 944 PCI_SLOT(dev->devfn) < via_vlink_dev_lo) 945 return; 946 947 /* This is an internal VLink device on a PIC interrupt. The BIOS 948 ought to have set this but may not have, so we redo it */ 949 950 pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq); 951 if (new_irq != irq) { 952 dev_info(&dev->dev, "VIA VLink IRQ fixup, from %d to %d\n", 953 irq, new_irq); 954 udelay(15); /* unknown if delay really needed */ 955 pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq); 956 } 957 } 958 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_vlink); 959 960 /* 961 * VIA VT82C598 has its device ID settable and many BIOSes 962 * set it to the ID of VT82C597 for backward compatibility. 963 * We need to switch it off to be able to recognize the real 964 * type of the chip. 965 */ 966 static void quirk_vt82c598_id(struct pci_dev *dev) 967 { 968 pci_write_config_byte(dev, 0xfc, 0); 969 pci_read_config_word(dev, PCI_DEVICE_ID, &dev->device); 970 } 971 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_vt82c598_id); 972 973 /* 974 * CardBus controllers have a legacy base address that enables them 975 * to respond as i82365 pcmcia controllers. We don't want them to 976 * do this even if the Linux CardBus driver is not loaded, because 977 * the Linux i82365 driver does not (and should not) handle CardBus. 978 */ 979 static void quirk_cardbus_legacy(struct pci_dev *dev) 980 { 981 pci_write_config_dword(dev, PCI_CB_LEGACY_MODE_BASE, 0); 982 } 983 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID, 984 PCI_CLASS_BRIDGE_CARDBUS, 8, quirk_cardbus_legacy); 985 DECLARE_PCI_FIXUP_CLASS_RESUME_EARLY(PCI_ANY_ID, PCI_ANY_ID, 986 PCI_CLASS_BRIDGE_CARDBUS, 8, quirk_cardbus_legacy); 987 988 /* 989 * Following the PCI ordering rules is optional on the AMD762. I'm not 990 * sure what the designers were smoking but let's not inhale... 991 * 992 * To be fair to AMD, it follows the spec by default, its BIOS people 993 * who turn it off! 994 */ 995 static void quirk_amd_ordering(struct pci_dev *dev) 996 { 997 u32 pcic; 998 pci_read_config_dword(dev, 0x4C, &pcic); 999 if ((pcic & 6) != 6) { 1000 pcic |= 6; 1001 dev_warn(&dev->dev, "BIOS failed to enable PCI standards compliance; fixing this error\n"); 1002 pci_write_config_dword(dev, 0x4C, pcic); 1003 pci_read_config_dword(dev, 0x84, &pcic); 1004 pcic |= (1 << 23); /* Required in this mode */ 1005 pci_write_config_dword(dev, 0x84, pcic); 1006 } 1007 } 1008 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering); 1009 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering); 1010 1011 /* 1012 * DreamWorks provided workaround for Dunord I-3000 problem 1013 * 1014 * This card decodes and responds to addresses not apparently 1015 * assigned to it. We force a larger allocation to ensure that 1016 * nothing gets put too close to it. 1017 */ 1018 static void quirk_dunord(struct pci_dev *dev) 1019 { 1020 struct resource *r = &dev->resource[1]; 1021 1022 r->flags |= IORESOURCE_UNSET; 1023 r->start = 0; 1024 r->end = 0xffffff; 1025 } 1026 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_DUNORD, PCI_DEVICE_ID_DUNORD_I3000, quirk_dunord); 1027 1028 /* 1029 * i82380FB mobile docking controller: its PCI-to-PCI bridge 1030 * is subtractive decoding (transparent), and does indicate this 1031 * in the ProgIf. Unfortunately, the ProgIf value is wrong - 0x80 1032 * instead of 0x01. 1033 */ 1034 static void quirk_transparent_bridge(struct pci_dev *dev) 1035 { 1036 dev->transparent = 1; 1037 } 1038 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82380FB, quirk_transparent_bridge); 1039 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA, 0x605, quirk_transparent_bridge); 1040 1041 /* 1042 * Common misconfiguration of the MediaGX/Geode PCI master that will 1043 * reduce PCI bandwidth from 70MB/s to 25MB/s. See the GXM/GXLV/GX1 1044 * datasheets found at http://www.national.com/analog for info on what 1045 * these bits do. <christer@weinigel.se> 1046 */ 1047 static void quirk_mediagx_master(struct pci_dev *dev) 1048 { 1049 u8 reg; 1050 1051 pci_read_config_byte(dev, 0x41, ®); 1052 if (reg & 2) { 1053 reg &= ~2; 1054 dev_info(&dev->dev, "Fixup for MediaGX/Geode Slave Disconnect Boundary (0x41=0x%02x)\n", 1055 reg); 1056 pci_write_config_byte(dev, 0x41, reg); 1057 } 1058 } 1059 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master); 1060 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master); 1061 1062 /* 1063 * Ensure C0 rev restreaming is off. This is normally done by 1064 * the BIOS but in the odd case it is not the results are corruption 1065 * hence the presence of a Linux check 1066 */ 1067 static void quirk_disable_pxb(struct pci_dev *pdev) 1068 { 1069 u16 config; 1070 1071 if (pdev->revision != 0x04) /* Only C0 requires this */ 1072 return; 1073 pci_read_config_word(pdev, 0x40, &config); 1074 if (config & (1<<6)) { 1075 config &= ~(1<<6); 1076 pci_write_config_word(pdev, 0x40, config); 1077 dev_info(&pdev->dev, "C0 revision 450NX. Disabling PCI restreaming\n"); 1078 } 1079 } 1080 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb); 1081 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb); 1082 1083 static void quirk_amd_ide_mode(struct pci_dev *pdev) 1084 { 1085 /* set SBX00/Hudson-2 SATA in IDE mode to AHCI mode */ 1086 u8 tmp; 1087 1088 pci_read_config_byte(pdev, PCI_CLASS_DEVICE, &tmp); 1089 if (tmp == 0x01) { 1090 pci_read_config_byte(pdev, 0x40, &tmp); 1091 pci_write_config_byte(pdev, 0x40, tmp|1); 1092 pci_write_config_byte(pdev, 0x9, 1); 1093 pci_write_config_byte(pdev, 0xa, 6); 1094 pci_write_config_byte(pdev, 0x40, tmp); 1095 1096 pdev->class = PCI_CLASS_STORAGE_SATA_AHCI; 1097 dev_info(&pdev->dev, "set SATA to AHCI mode\n"); 1098 } 1099 } 1100 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_amd_ide_mode); 1101 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_amd_ide_mode); 1102 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_amd_ide_mode); 1103 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_amd_ide_mode); 1104 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA_IDE, quirk_amd_ide_mode); 1105 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA_IDE, quirk_amd_ide_mode); 1106 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x7900, quirk_amd_ide_mode); 1107 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, 0x7900, quirk_amd_ide_mode); 1108 1109 /* 1110 * Serverworks CSB5 IDE does not fully support native mode 1111 */ 1112 static void quirk_svwks_csb5ide(struct pci_dev *pdev) 1113 { 1114 u8 prog; 1115 pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); 1116 if (prog & 5) { 1117 prog &= ~5; 1118 pdev->class &= ~5; 1119 pci_write_config_byte(pdev, PCI_CLASS_PROG, prog); 1120 /* PCI layer will sort out resources */ 1121 } 1122 } 1123 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, quirk_svwks_csb5ide); 1124 1125 /* 1126 * Intel 82801CAM ICH3-M datasheet says IDE modes must be the same 1127 */ 1128 static void quirk_ide_samemode(struct pci_dev *pdev) 1129 { 1130 u8 prog; 1131 1132 pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); 1133 1134 if (((prog & 1) && !(prog & 4)) || ((prog & 4) && !(prog & 1))) { 1135 dev_info(&pdev->dev, "IDE mode mismatch; forcing legacy mode\n"); 1136 prog &= ~5; 1137 pdev->class &= ~5; 1138 pci_write_config_byte(pdev, PCI_CLASS_PROG, prog); 1139 } 1140 } 1141 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, quirk_ide_samemode); 1142 1143 /* 1144 * Some ATA devices break if put into D3 1145 */ 1146 1147 static void quirk_no_ata_d3(struct pci_dev *pdev) 1148 { 1149 pdev->dev_flags |= PCI_DEV_FLAGS_NO_D3; 1150 } 1151 /* Quirk the legacy ATA devices only. The AHCI ones are ok */ 1152 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_ANY_ID, 1153 PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3); 1154 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_ATI, PCI_ANY_ID, 1155 PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3); 1156 /* ALi loses some register settings that we cannot then restore */ 1157 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID, 1158 PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3); 1159 /* VIA comes back fine but we need to keep it alive or ACPI GTM failures 1160 occur when mode detecting */ 1161 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_VIA, PCI_ANY_ID, 1162 PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3); 1163 1164 /* This was originally an Alpha specific thing, but it really fits here. 1165 * The i82375 PCI/EISA bridge appears as non-classified. Fix that. 1166 */ 1167 static void quirk_eisa_bridge(struct pci_dev *dev) 1168 { 1169 dev->class = PCI_CLASS_BRIDGE_EISA << 8; 1170 } 1171 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82375, quirk_eisa_bridge); 1172 1173 1174 /* 1175 * On ASUS P4B boards, the SMBus PCI Device within the ICH2/4 southbridge 1176 * is not activated. The myth is that Asus said that they do not want the 1177 * users to be irritated by just another PCI Device in the Win98 device 1178 * manager. (see the file prog/hotplug/README.p4b in the lm_sensors 1179 * package 2.7.0 for details) 1180 * 1181 * The SMBus PCI Device can be activated by setting a bit in the ICH LPC 1182 * bridge. Unfortunately, this device has no subvendor/subdevice ID. So it 1183 * becomes necessary to do this tweak in two steps -- the chosen trigger 1184 * is either the Host bridge (preferred) or on-board VGA controller. 1185 * 1186 * Note that we used to unhide the SMBus that way on Toshiba laptops 1187 * (Satellite A40 and Tecra M2) but then found that the thermal management 1188 * was done by SMM code, which could cause unsynchronized concurrent 1189 * accesses to the SMBus registers, with potentially bad effects. Thus you 1190 * should be very careful when adding new entries: if SMM is accessing the 1191 * Intel SMBus, this is a very good reason to leave it hidden. 1192 * 1193 * Likewise, many recent laptops use ACPI for thermal management. If the 1194 * ACPI DSDT code accesses the SMBus, then Linux should not access it 1195 * natively, and keeping the SMBus hidden is the right thing to do. If you 1196 * are about to add an entry in the table below, please first disassemble 1197 * the DSDT and double-check that there is no code accessing the SMBus. 1198 */ 1199 static int asus_hides_smbus; 1200 1201 static void asus_hides_smbus_hostbridge(struct pci_dev *dev) 1202 { 1203 if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) { 1204 if (dev->device == PCI_DEVICE_ID_INTEL_82845_HB) 1205 switch (dev->subsystem_device) { 1206 case 0x8025: /* P4B-LX */ 1207 case 0x8070: /* P4B */ 1208 case 0x8088: /* P4B533 */ 1209 case 0x1626: /* L3C notebook */ 1210 asus_hides_smbus = 1; 1211 } 1212 else if (dev->device == PCI_DEVICE_ID_INTEL_82845G_HB) 1213 switch (dev->subsystem_device) { 1214 case 0x80b1: /* P4GE-V */ 1215 case 0x80b2: /* P4PE */ 1216 case 0x8093: /* P4B533-V */ 1217 asus_hides_smbus = 1; 1218 } 1219 else if (dev->device == PCI_DEVICE_ID_INTEL_82850_HB) 1220 switch (dev->subsystem_device) { 1221 case 0x8030: /* P4T533 */ 1222 asus_hides_smbus = 1; 1223 } 1224 else if (dev->device == PCI_DEVICE_ID_INTEL_7205_0) 1225 switch (dev->subsystem_device) { 1226 case 0x8070: /* P4G8X Deluxe */ 1227 asus_hides_smbus = 1; 1228 } 1229 else if (dev->device == PCI_DEVICE_ID_INTEL_E7501_MCH) 1230 switch (dev->subsystem_device) { 1231 case 0x80c9: /* PU-DLS */ 1232 asus_hides_smbus = 1; 1233 } 1234 else if (dev->device == PCI_DEVICE_ID_INTEL_82855GM_HB) 1235 switch (dev->subsystem_device) { 1236 case 0x1751: /* M2N notebook */ 1237 case 0x1821: /* M5N notebook */ 1238 case 0x1897: /* A6L notebook */ 1239 asus_hides_smbus = 1; 1240 } 1241 else if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 1242 switch (dev->subsystem_device) { 1243 case 0x184b: /* W1N notebook */ 1244 case 0x186a: /* M6Ne notebook */ 1245 asus_hides_smbus = 1; 1246 } 1247 else if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB) 1248 switch (dev->subsystem_device) { 1249 case 0x80f2: /* P4P800-X */ 1250 asus_hides_smbus = 1; 1251 } 1252 else if (dev->device == PCI_DEVICE_ID_INTEL_82915GM_HB) 1253 switch (dev->subsystem_device) { 1254 case 0x1882: /* M6V notebook */ 1255 case 0x1977: /* A6VA notebook */ 1256 asus_hides_smbus = 1; 1257 } 1258 } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_HP)) { 1259 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 1260 switch (dev->subsystem_device) { 1261 case 0x088C: /* HP Compaq nc8000 */ 1262 case 0x0890: /* HP Compaq nc6000 */ 1263 asus_hides_smbus = 1; 1264 } 1265 else if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB) 1266 switch (dev->subsystem_device) { 1267 case 0x12bc: /* HP D330L */ 1268 case 0x12bd: /* HP D530 */ 1269 case 0x006a: /* HP Compaq nx9500 */ 1270 asus_hides_smbus = 1; 1271 } 1272 else if (dev->device == PCI_DEVICE_ID_INTEL_82875_HB) 1273 switch (dev->subsystem_device) { 1274 case 0x12bf: /* HP xw4100 */ 1275 asus_hides_smbus = 1; 1276 } 1277 } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG)) { 1278 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 1279 switch (dev->subsystem_device) { 1280 case 0xC00C: /* Samsung P35 notebook */ 1281 asus_hides_smbus = 1; 1282 } 1283 } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_COMPAQ)) { 1284 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 1285 switch (dev->subsystem_device) { 1286 case 0x0058: /* Compaq Evo N620c */ 1287 asus_hides_smbus = 1; 1288 } 1289 else if (dev->device == PCI_DEVICE_ID_INTEL_82810_IG3) 1290 switch (dev->subsystem_device) { 1291 case 0xB16C: /* Compaq Deskpro EP 401963-001 (PCA# 010174) */ 1292 /* Motherboard doesn't have Host bridge 1293 * subvendor/subdevice IDs, therefore checking 1294 * its on-board VGA controller */ 1295 asus_hides_smbus = 1; 1296 } 1297 else if (dev->device == PCI_DEVICE_ID_INTEL_82801DB_2) 1298 switch (dev->subsystem_device) { 1299 case 0x00b8: /* Compaq Evo D510 CMT */ 1300 case 0x00b9: /* Compaq Evo D510 SFF */ 1301 case 0x00ba: /* Compaq Evo D510 USDT */ 1302 /* Motherboard doesn't have Host bridge 1303 * subvendor/subdevice IDs and on-board VGA 1304 * controller is disabled if an AGP card is 1305 * inserted, therefore checking USB UHCI 1306 * Controller #1 */ 1307 asus_hides_smbus = 1; 1308 } 1309 else if (dev->device == PCI_DEVICE_ID_INTEL_82815_CGC) 1310 switch (dev->subsystem_device) { 1311 case 0x001A: /* Compaq Deskpro EN SSF P667 815E */ 1312 /* Motherboard doesn't have host bridge 1313 * subvendor/subdevice IDs, therefore checking 1314 * its on-board VGA controller */ 1315 asus_hides_smbus = 1; 1316 } 1317 } 1318 } 1319 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845_HB, asus_hides_smbus_hostbridge); 1320 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845G_HB, asus_hides_smbus_hostbridge); 1321 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82850_HB, asus_hides_smbus_hostbridge); 1322 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB, asus_hides_smbus_hostbridge); 1323 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82875_HB, asus_hides_smbus_hostbridge); 1324 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_7205_0, asus_hides_smbus_hostbridge); 1325 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7501_MCH, asus_hides_smbus_hostbridge); 1326 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855PM_HB, asus_hides_smbus_hostbridge); 1327 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855GM_HB, asus_hides_smbus_hostbridge); 1328 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82915GM_HB, asus_hides_smbus_hostbridge); 1329 1330 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82810_IG3, asus_hides_smbus_hostbridge); 1331 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_2, asus_hides_smbus_hostbridge); 1332 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82815_CGC, asus_hides_smbus_hostbridge); 1333 1334 static void asus_hides_smbus_lpc(struct pci_dev *dev) 1335 { 1336 u16 val; 1337 1338 if (likely(!asus_hides_smbus)) 1339 return; 1340 1341 pci_read_config_word(dev, 0xF2, &val); 1342 if (val & 0x8) { 1343 pci_write_config_word(dev, 0xF2, val & (~0x8)); 1344 pci_read_config_word(dev, 0xF2, &val); 1345 if (val & 0x8) 1346 dev_info(&dev->dev, "i801 SMBus device continues to play 'hide and seek'! 0x%x\n", 1347 val); 1348 else 1349 dev_info(&dev->dev, "Enabled i801 SMBus device\n"); 1350 } 1351 } 1352 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, asus_hides_smbus_lpc); 1353 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc); 1354 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc); 1355 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, asus_hides_smbus_lpc); 1356 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc); 1357 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc); 1358 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc); 1359 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, asus_hides_smbus_lpc); 1360 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc); 1361 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc); 1362 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, asus_hides_smbus_lpc); 1363 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc); 1364 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc); 1365 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc); 1366 1367 /* It appears we just have one such device. If not, we have a warning */ 1368 static void __iomem *asus_rcba_base; 1369 static void asus_hides_smbus_lpc_ich6_suspend(struct pci_dev *dev) 1370 { 1371 u32 rcba; 1372 1373 if (likely(!asus_hides_smbus)) 1374 return; 1375 WARN_ON(asus_rcba_base); 1376 1377 pci_read_config_dword(dev, 0xF0, &rcba); 1378 /* use bits 31:14, 16 kB aligned */ 1379 asus_rcba_base = ioremap_nocache(rcba & 0xFFFFC000, 0x4000); 1380 if (asus_rcba_base == NULL) 1381 return; 1382 } 1383 1384 static void asus_hides_smbus_lpc_ich6_resume_early(struct pci_dev *dev) 1385 { 1386 u32 val; 1387 1388 if (likely(!asus_hides_smbus || !asus_rcba_base)) 1389 return; 1390 /* read the Function Disable register, dword mode only */ 1391 val = readl(asus_rcba_base + 0x3418); 1392 writel(val & 0xFFFFFFF7, asus_rcba_base + 0x3418); /* enable the SMBus device */ 1393 } 1394 1395 static void asus_hides_smbus_lpc_ich6_resume(struct pci_dev *dev) 1396 { 1397 if (likely(!asus_hides_smbus || !asus_rcba_base)) 1398 return; 1399 iounmap(asus_rcba_base); 1400 asus_rcba_base = NULL; 1401 dev_info(&dev->dev, "Enabled ICH6/i801 SMBus device\n"); 1402 } 1403 1404 static void asus_hides_smbus_lpc_ich6(struct pci_dev *dev) 1405 { 1406 asus_hides_smbus_lpc_ich6_suspend(dev); 1407 asus_hides_smbus_lpc_ich6_resume_early(dev); 1408 asus_hides_smbus_lpc_ich6_resume(dev); 1409 } 1410 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6); 1411 DECLARE_PCI_FIXUP_SUSPEND(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_suspend); 1412 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_resume); 1413 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_resume_early); 1414 1415 /* 1416 * SiS 96x south bridge: BIOS typically hides SMBus device... 1417 */ 1418 static void quirk_sis_96x_smbus(struct pci_dev *dev) 1419 { 1420 u8 val = 0; 1421 pci_read_config_byte(dev, 0x77, &val); 1422 if (val & 0x10) { 1423 dev_info(&dev->dev, "Enabling SiS 96x SMBus\n"); 1424 pci_write_config_byte(dev, 0x77, val & ~0x10); 1425 } 1426 } 1427 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus); 1428 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus); 1429 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus); 1430 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus); 1431 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus); 1432 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus); 1433 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus); 1434 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus); 1435 1436 /* 1437 * ... This is further complicated by the fact that some SiS96x south 1438 * bridges pretend to be 85C503/5513 instead. In that case see if we 1439 * spotted a compatible north bridge to make sure. 1440 * (pci_find_device doesn't work yet) 1441 * 1442 * We can also enable the sis96x bit in the discovery register.. 1443 */ 1444 #define SIS_DETECT_REGISTER 0x40 1445 1446 static void quirk_sis_503(struct pci_dev *dev) 1447 { 1448 u8 reg; 1449 u16 devid; 1450 1451 pci_read_config_byte(dev, SIS_DETECT_REGISTER, ®); 1452 pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg | (1 << 6)); 1453 pci_read_config_word(dev, PCI_DEVICE_ID, &devid); 1454 if (((devid & 0xfff0) != 0x0960) && (devid != 0x0018)) { 1455 pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg); 1456 return; 1457 } 1458 1459 /* 1460 * Ok, it now shows up as a 96x.. run the 96x quirk by 1461 * hand in case it has already been processed. 1462 * (depends on link order, which is apparently not guaranteed) 1463 */ 1464 dev->device = devid; 1465 quirk_sis_96x_smbus(dev); 1466 } 1467 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503); 1468 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503); 1469 1470 1471 /* 1472 * On ASUS A8V and A8V Deluxe boards, the onboard AC97 audio controller 1473 * and MC97 modem controller are disabled when a second PCI soundcard is 1474 * present. This patch, tweaking the VT8237 ISA bridge, enables them. 1475 * -- bjd 1476 */ 1477 static void asus_hides_ac97_lpc(struct pci_dev *dev) 1478 { 1479 u8 val; 1480 int asus_hides_ac97 = 0; 1481 1482 if (likely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) { 1483 if (dev->device == PCI_DEVICE_ID_VIA_8237) 1484 asus_hides_ac97 = 1; 1485 } 1486 1487 if (!asus_hides_ac97) 1488 return; 1489 1490 pci_read_config_byte(dev, 0x50, &val); 1491 if (val & 0xc0) { 1492 pci_write_config_byte(dev, 0x50, val & (~0xc0)); 1493 pci_read_config_byte(dev, 0x50, &val); 1494 if (val & 0xc0) 1495 dev_info(&dev->dev, "Onboard AC97/MC97 devices continue to play 'hide and seek'! 0x%x\n", 1496 val); 1497 else 1498 dev_info(&dev->dev, "Enabled onboard AC97/MC97 devices\n"); 1499 } 1500 } 1501 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, asus_hides_ac97_lpc); 1502 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, asus_hides_ac97_lpc); 1503 1504 #if defined(CONFIG_ATA) || defined(CONFIG_ATA_MODULE) 1505 1506 /* 1507 * If we are using libata we can drive this chip properly but must 1508 * do this early on to make the additional device appear during 1509 * the PCI scanning. 1510 */ 1511 static void quirk_jmicron_ata(struct pci_dev *pdev) 1512 { 1513 u32 conf1, conf5, class; 1514 u8 hdr; 1515 1516 /* Only poke fn 0 */ 1517 if (PCI_FUNC(pdev->devfn)) 1518 return; 1519 1520 pci_read_config_dword(pdev, 0x40, &conf1); 1521 pci_read_config_dword(pdev, 0x80, &conf5); 1522 1523 conf1 &= ~0x00CFF302; /* Clear bit 1, 8, 9, 12-19, 22, 23 */ 1524 conf5 &= ~(1 << 24); /* Clear bit 24 */ 1525 1526 switch (pdev->device) { 1527 case PCI_DEVICE_ID_JMICRON_JMB360: /* SATA single port */ 1528 case PCI_DEVICE_ID_JMICRON_JMB362: /* SATA dual ports */ 1529 case PCI_DEVICE_ID_JMICRON_JMB364: /* SATA dual ports */ 1530 /* The controller should be in single function ahci mode */ 1531 conf1 |= 0x0002A100; /* Set 8, 13, 15, 17 */ 1532 break; 1533 1534 case PCI_DEVICE_ID_JMICRON_JMB365: 1535 case PCI_DEVICE_ID_JMICRON_JMB366: 1536 /* Redirect IDE second PATA port to the right spot */ 1537 conf5 |= (1 << 24); 1538 /* Fall through */ 1539 case PCI_DEVICE_ID_JMICRON_JMB361: 1540 case PCI_DEVICE_ID_JMICRON_JMB363: 1541 case PCI_DEVICE_ID_JMICRON_JMB369: 1542 /* Enable dual function mode, AHCI on fn 0, IDE fn1 */ 1543 /* Set the class codes correctly and then direct IDE 0 */ 1544 conf1 |= 0x00C2A1B3; /* Set 0, 1, 4, 5, 7, 8, 13, 15, 17, 22, 23 */ 1545 break; 1546 1547 case PCI_DEVICE_ID_JMICRON_JMB368: 1548 /* The controller should be in single function IDE mode */ 1549 conf1 |= 0x00C00000; /* Set 22, 23 */ 1550 break; 1551 } 1552 1553 pci_write_config_dword(pdev, 0x40, conf1); 1554 pci_write_config_dword(pdev, 0x80, conf5); 1555 1556 /* Update pdev accordingly */ 1557 pci_read_config_byte(pdev, PCI_HEADER_TYPE, &hdr); 1558 pdev->hdr_type = hdr & 0x7f; 1559 pdev->multifunction = !!(hdr & 0x80); 1560 1561 pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class); 1562 pdev->class = class >> 8; 1563 } 1564 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata); 1565 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata); 1566 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata); 1567 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata); 1568 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB364, quirk_jmicron_ata); 1569 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata); 1570 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata); 1571 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata); 1572 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB369, quirk_jmicron_ata); 1573 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata); 1574 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata); 1575 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata); 1576 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata); 1577 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB364, quirk_jmicron_ata); 1578 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata); 1579 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata); 1580 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata); 1581 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB369, quirk_jmicron_ata); 1582 1583 #endif 1584 1585 static void quirk_jmicron_async_suspend(struct pci_dev *dev) 1586 { 1587 if (dev->multifunction) { 1588 device_disable_async_suspend(&dev->dev); 1589 dev_info(&dev->dev, "async suspend disabled to avoid multi-function power-on ordering issue\n"); 1590 } 1591 } 1592 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE, 8, quirk_jmicron_async_suspend); 1593 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_CLASS_STORAGE_SATA_AHCI, 0, quirk_jmicron_async_suspend); 1594 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_JMICRON, 0x2362, quirk_jmicron_async_suspend); 1595 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_JMICRON, 0x236f, quirk_jmicron_async_suspend); 1596 1597 #ifdef CONFIG_X86_IO_APIC 1598 static void quirk_alder_ioapic(struct pci_dev *pdev) 1599 { 1600 int i; 1601 1602 if ((pdev->class >> 8) != 0xff00) 1603 return; 1604 1605 /* the first BAR is the location of the IO APIC...we must 1606 * not touch this (and it's already covered by the fixmap), so 1607 * forcibly insert it into the resource tree */ 1608 if (pci_resource_start(pdev, 0) && pci_resource_len(pdev, 0)) 1609 insert_resource(&iomem_resource, &pdev->resource[0]); 1610 1611 /* The next five BARs all seem to be rubbish, so just clean 1612 * them out */ 1613 for (i = 1; i < 6; i++) 1614 memset(&pdev->resource[i], 0, sizeof(pdev->resource[i])); 1615 } 1616 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EESSC, quirk_alder_ioapic); 1617 #endif 1618 1619 static void quirk_pcie_mch(struct pci_dev *pdev) 1620 { 1621 pdev->no_msi = 1; 1622 } 1623 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, quirk_pcie_mch); 1624 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7320_MCH, quirk_pcie_mch); 1625 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7525_MCH, quirk_pcie_mch); 1626 1627 1628 /* 1629 * It's possible for the MSI to get corrupted if shpc and acpi 1630 * are used together on certain PXH-based systems. 1631 */ 1632 static void quirk_pcie_pxh(struct pci_dev *dev) 1633 { 1634 dev->no_msi = 1; 1635 dev_warn(&dev->dev, "PXH quirk detected; SHPC device MSI disabled\n"); 1636 } 1637 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_0, quirk_pcie_pxh); 1638 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_1, quirk_pcie_pxh); 1639 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_pcie_pxh); 1640 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_pcie_pxh); 1641 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_pcie_pxh); 1642 1643 /* 1644 * Some Intel PCI Express chipsets have trouble with downstream 1645 * device power management. 1646 */ 1647 static void quirk_intel_pcie_pm(struct pci_dev *dev) 1648 { 1649 pci_pm_d3_delay = 120; 1650 dev->no_d1d2 = 1; 1651 } 1652 1653 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e2, quirk_intel_pcie_pm); 1654 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e3, quirk_intel_pcie_pm); 1655 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e4, quirk_intel_pcie_pm); 1656 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e5, quirk_intel_pcie_pm); 1657 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e6, quirk_intel_pcie_pm); 1658 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e7, quirk_intel_pcie_pm); 1659 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f7, quirk_intel_pcie_pm); 1660 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f8, quirk_intel_pcie_pm); 1661 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f9, quirk_intel_pcie_pm); 1662 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25fa, quirk_intel_pcie_pm); 1663 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2601, quirk_intel_pcie_pm); 1664 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2602, quirk_intel_pcie_pm); 1665 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2603, quirk_intel_pcie_pm); 1666 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2604, quirk_intel_pcie_pm); 1667 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2605, quirk_intel_pcie_pm); 1668 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2606, quirk_intel_pcie_pm); 1669 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2607, quirk_intel_pcie_pm); 1670 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2608, quirk_intel_pcie_pm); 1671 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2609, quirk_intel_pcie_pm); 1672 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260a, quirk_intel_pcie_pm); 1673 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260b, quirk_intel_pcie_pm); 1674 1675 #ifdef CONFIG_X86_IO_APIC 1676 /* 1677 * Boot interrupts on some chipsets cannot be turned off. For these chipsets, 1678 * remap the original interrupt in the linux kernel to the boot interrupt, so 1679 * that a PCI device's interrupt handler is installed on the boot interrupt 1680 * line instead. 1681 */ 1682 static void quirk_reroute_to_boot_interrupts_intel(struct pci_dev *dev) 1683 { 1684 if (noioapicquirk || noioapicreroute) 1685 return; 1686 1687 dev->irq_reroute_variant = INTEL_IRQ_REROUTE_VARIANT; 1688 dev_info(&dev->dev, "rerouting interrupts for [%04x:%04x]\n", 1689 dev->vendor, dev->device); 1690 } 1691 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_0, quirk_reroute_to_boot_interrupts_intel); 1692 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_1, quirk_reroute_to_boot_interrupts_intel); 1693 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, quirk_reroute_to_boot_interrupts_intel); 1694 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_reroute_to_boot_interrupts_intel); 1695 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_reroute_to_boot_interrupts_intel); 1696 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_reroute_to_boot_interrupts_intel); 1697 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_0, quirk_reroute_to_boot_interrupts_intel); 1698 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_1, quirk_reroute_to_boot_interrupts_intel); 1699 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_0, quirk_reroute_to_boot_interrupts_intel); 1700 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_1, quirk_reroute_to_boot_interrupts_intel); 1701 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, quirk_reroute_to_boot_interrupts_intel); 1702 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_reroute_to_boot_interrupts_intel); 1703 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_reroute_to_boot_interrupts_intel); 1704 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_reroute_to_boot_interrupts_intel); 1705 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_0, quirk_reroute_to_boot_interrupts_intel); 1706 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_1, quirk_reroute_to_boot_interrupts_intel); 1707 1708 /* 1709 * On some chipsets we can disable the generation of legacy INTx boot 1710 * interrupts. 1711 */ 1712 1713 /* 1714 * IO-APIC1 on 6300ESB generates boot interrupts, see intel order no 1715 * 300641-004US, section 5.7.3. 1716 */ 1717 #define INTEL_6300_IOAPIC_ABAR 0x40 1718 #define INTEL_6300_DISABLE_BOOT_IRQ (1<<14) 1719 1720 static void quirk_disable_intel_boot_interrupt(struct pci_dev *dev) 1721 { 1722 u16 pci_config_word; 1723 1724 if (noioapicquirk) 1725 return; 1726 1727 pci_read_config_word(dev, INTEL_6300_IOAPIC_ABAR, &pci_config_word); 1728 pci_config_word |= INTEL_6300_DISABLE_BOOT_IRQ; 1729 pci_write_config_word(dev, INTEL_6300_IOAPIC_ABAR, pci_config_word); 1730 1731 dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n", 1732 dev->vendor, dev->device); 1733 } 1734 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_10, quirk_disable_intel_boot_interrupt); 1735 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_10, quirk_disable_intel_boot_interrupt); 1736 1737 /* 1738 * disable boot interrupts on HT-1000 1739 */ 1740 #define BC_HT1000_FEATURE_REG 0x64 1741 #define BC_HT1000_PIC_REGS_ENABLE (1<<0) 1742 #define BC_HT1000_MAP_IDX 0xC00 1743 #define BC_HT1000_MAP_DATA 0xC01 1744 1745 static void quirk_disable_broadcom_boot_interrupt(struct pci_dev *dev) 1746 { 1747 u32 pci_config_dword; 1748 u8 irq; 1749 1750 if (noioapicquirk) 1751 return; 1752 1753 pci_read_config_dword(dev, BC_HT1000_FEATURE_REG, &pci_config_dword); 1754 pci_write_config_dword(dev, BC_HT1000_FEATURE_REG, pci_config_dword | 1755 BC_HT1000_PIC_REGS_ENABLE); 1756 1757 for (irq = 0x10; irq < 0x10 + 32; irq++) { 1758 outb(irq, BC_HT1000_MAP_IDX); 1759 outb(0x00, BC_HT1000_MAP_DATA); 1760 } 1761 1762 pci_write_config_dword(dev, BC_HT1000_FEATURE_REG, pci_config_dword); 1763 1764 dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n", 1765 dev->vendor, dev->device); 1766 } 1767 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000SB, quirk_disable_broadcom_boot_interrupt); 1768 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000SB, quirk_disable_broadcom_boot_interrupt); 1769 1770 /* 1771 * disable boot interrupts on AMD and ATI chipsets 1772 */ 1773 /* 1774 * NOIOAMODE needs to be disabled to disable "boot interrupts". For AMD 8131 1775 * rev. A0 and B0, NOIOAMODE needs to be disabled anyway to fix IO-APIC mode 1776 * (due to an erratum). 1777 */ 1778 #define AMD_813X_MISC 0x40 1779 #define AMD_813X_NOIOAMODE (1<<0) 1780 #define AMD_813X_REV_B1 0x12 1781 #define AMD_813X_REV_B2 0x13 1782 1783 static void quirk_disable_amd_813x_boot_interrupt(struct pci_dev *dev) 1784 { 1785 u32 pci_config_dword; 1786 1787 if (noioapicquirk) 1788 return; 1789 if ((dev->revision == AMD_813X_REV_B1) || 1790 (dev->revision == AMD_813X_REV_B2)) 1791 return; 1792 1793 pci_read_config_dword(dev, AMD_813X_MISC, &pci_config_dword); 1794 pci_config_dword &= ~AMD_813X_NOIOAMODE; 1795 pci_write_config_dword(dev, AMD_813X_MISC, pci_config_dword); 1796 1797 dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n", 1798 dev->vendor, dev->device); 1799 } 1800 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_amd_813x_boot_interrupt); 1801 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_amd_813x_boot_interrupt); 1802 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, quirk_disable_amd_813x_boot_interrupt); 1803 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, quirk_disable_amd_813x_boot_interrupt); 1804 1805 #define AMD_8111_PCI_IRQ_ROUTING 0x56 1806 1807 static void quirk_disable_amd_8111_boot_interrupt(struct pci_dev *dev) 1808 { 1809 u16 pci_config_word; 1810 1811 if (noioapicquirk) 1812 return; 1813 1814 pci_read_config_word(dev, AMD_8111_PCI_IRQ_ROUTING, &pci_config_word); 1815 if (!pci_config_word) { 1816 dev_info(&dev->dev, "boot interrupts on device [%04x:%04x] already disabled\n", 1817 dev->vendor, dev->device); 1818 return; 1819 } 1820 pci_write_config_word(dev, AMD_8111_PCI_IRQ_ROUTING, 0); 1821 dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n", 1822 dev->vendor, dev->device); 1823 } 1824 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS, quirk_disable_amd_8111_boot_interrupt); 1825 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS, quirk_disable_amd_8111_boot_interrupt); 1826 #endif /* CONFIG_X86_IO_APIC */ 1827 1828 /* 1829 * Toshiba TC86C001 IDE controller reports the standard 8-byte BAR0 size 1830 * but the PIO transfers won't work if BAR0 falls at the odd 8 bytes. 1831 * Re-allocate the region if needed... 1832 */ 1833 static void quirk_tc86c001_ide(struct pci_dev *dev) 1834 { 1835 struct resource *r = &dev->resource[0]; 1836 1837 if (r->start & 0x8) { 1838 r->flags |= IORESOURCE_UNSET; 1839 r->start = 0; 1840 r->end = 0xf; 1841 } 1842 } 1843 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA_2, 1844 PCI_DEVICE_ID_TOSHIBA_TC86C001_IDE, 1845 quirk_tc86c001_ide); 1846 1847 /* 1848 * PLX PCI 9050 PCI Target bridge controller has an errata that prevents the 1849 * local configuration registers accessible via BAR0 (memory) or BAR1 (i/o) 1850 * being read correctly if bit 7 of the base address is set. 1851 * The BAR0 or BAR1 region may be disabled (size 0) or enabled (size 128). 1852 * Re-allocate the regions to a 256-byte boundary if necessary. 1853 */ 1854 static void quirk_plx_pci9050(struct pci_dev *dev) 1855 { 1856 unsigned int bar; 1857 1858 /* Fixed in revision 2 (PCI 9052). */ 1859 if (dev->revision >= 2) 1860 return; 1861 for (bar = 0; bar <= 1; bar++) 1862 if (pci_resource_len(dev, bar) == 0x80 && 1863 (pci_resource_start(dev, bar) & 0x80)) { 1864 struct resource *r = &dev->resource[bar]; 1865 dev_info(&dev->dev, "Re-allocating PLX PCI 9050 BAR %u to length 256 to avoid bit 7 bug\n", 1866 bar); 1867 r->flags |= IORESOURCE_UNSET; 1868 r->start = 0; 1869 r->end = 0xff; 1870 } 1871 } 1872 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050, 1873 quirk_plx_pci9050); 1874 /* 1875 * The following Meilhaus (vendor ID 0x1402) device IDs (amongst others) 1876 * may be using the PLX PCI 9050: 0x0630, 0x0940, 0x0950, 0x0960, 0x100b, 1877 * 0x1400, 0x140a, 0x140b, 0x14e0, 0x14ea, 0x14eb, 0x1604, 0x1608, 0x160c, 1878 * 0x168f, 0x2000, 0x2600, 0x3000, 0x810a, 0x810b. 1879 * 1880 * Currently, device IDs 0x2000 and 0x2600 are used by the Comedi "me_daq" 1881 * driver. 1882 */ 1883 DECLARE_PCI_FIXUP_HEADER(0x1402, 0x2000, quirk_plx_pci9050); 1884 DECLARE_PCI_FIXUP_HEADER(0x1402, 0x2600, quirk_plx_pci9050); 1885 1886 static void quirk_netmos(struct pci_dev *dev) 1887 { 1888 unsigned int num_parallel = (dev->subsystem_device & 0xf0) >> 4; 1889 unsigned int num_serial = dev->subsystem_device & 0xf; 1890 1891 /* 1892 * These Netmos parts are multiport serial devices with optional 1893 * parallel ports. Even when parallel ports are present, they 1894 * are identified as class SERIAL, which means the serial driver 1895 * will claim them. To prevent this, mark them as class OTHER. 1896 * These combo devices should be claimed by parport_serial. 1897 * 1898 * The subdevice ID is of the form 0x00PS, where <P> is the number 1899 * of parallel ports and <S> is the number of serial ports. 1900 */ 1901 switch (dev->device) { 1902 case PCI_DEVICE_ID_NETMOS_9835: 1903 /* Well, this rule doesn't hold for the following 9835 device */ 1904 if (dev->subsystem_vendor == PCI_VENDOR_ID_IBM && 1905 dev->subsystem_device == 0x0299) 1906 return; 1907 case PCI_DEVICE_ID_NETMOS_9735: 1908 case PCI_DEVICE_ID_NETMOS_9745: 1909 case PCI_DEVICE_ID_NETMOS_9845: 1910 case PCI_DEVICE_ID_NETMOS_9855: 1911 if (num_parallel) { 1912 dev_info(&dev->dev, "Netmos %04x (%u parallel, %u serial); changing class SERIAL to OTHER (use parport_serial)\n", 1913 dev->device, num_parallel, num_serial); 1914 dev->class = (PCI_CLASS_COMMUNICATION_OTHER << 8) | 1915 (dev->class & 0xff); 1916 } 1917 } 1918 } 1919 DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_NETMOS, PCI_ANY_ID, 1920 PCI_CLASS_COMMUNICATION_SERIAL, 8, quirk_netmos); 1921 1922 /* 1923 * Quirk non-zero PCI functions to route VPD access through function 0 for 1924 * devices that share VPD resources between functions. The functions are 1925 * expected to be identical devices. 1926 */ 1927 static void quirk_f0_vpd_link(struct pci_dev *dev) 1928 { 1929 struct pci_dev *f0; 1930 1931 if (!PCI_FUNC(dev->devfn)) 1932 return; 1933 1934 f0 = pci_get_slot(dev->bus, PCI_DEVFN(PCI_SLOT(dev->devfn), 0)); 1935 if (!f0) 1936 return; 1937 1938 if (f0->vpd && dev->class == f0->class && 1939 dev->vendor == f0->vendor && dev->device == f0->device) 1940 dev->dev_flags |= PCI_DEV_FLAGS_VPD_REF_F0; 1941 1942 pci_dev_put(f0); 1943 } 1944 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, 1945 PCI_CLASS_NETWORK_ETHERNET, 8, quirk_f0_vpd_link); 1946 1947 static void quirk_e100_interrupt(struct pci_dev *dev) 1948 { 1949 u16 command, pmcsr; 1950 u8 __iomem *csr; 1951 u8 cmd_hi; 1952 1953 switch (dev->device) { 1954 /* PCI IDs taken from drivers/net/e100.c */ 1955 case 0x1029: 1956 case 0x1030 ... 0x1034: 1957 case 0x1038 ... 0x103E: 1958 case 0x1050 ... 0x1057: 1959 case 0x1059: 1960 case 0x1064 ... 0x106B: 1961 case 0x1091 ... 0x1095: 1962 case 0x1209: 1963 case 0x1229: 1964 case 0x2449: 1965 case 0x2459: 1966 case 0x245D: 1967 case 0x27DC: 1968 break; 1969 default: 1970 return; 1971 } 1972 1973 /* 1974 * Some firmware hands off the e100 with interrupts enabled, 1975 * which can cause a flood of interrupts if packets are 1976 * received before the driver attaches to the device. So 1977 * disable all e100 interrupts here. The driver will 1978 * re-enable them when it's ready. 1979 */ 1980 pci_read_config_word(dev, PCI_COMMAND, &command); 1981 1982 if (!(command & PCI_COMMAND_MEMORY) || !pci_resource_start(dev, 0)) 1983 return; 1984 1985 /* 1986 * Check that the device is in the D0 power state. If it's not, 1987 * there is no point to look any further. 1988 */ 1989 if (dev->pm_cap) { 1990 pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pmcsr); 1991 if ((pmcsr & PCI_PM_CTRL_STATE_MASK) != PCI_D0) 1992 return; 1993 } 1994 1995 /* Convert from PCI bus to resource space. */ 1996 csr = ioremap(pci_resource_start(dev, 0), 8); 1997 if (!csr) { 1998 dev_warn(&dev->dev, "Can't map e100 registers\n"); 1999 return; 2000 } 2001 2002 cmd_hi = readb(csr + 3); 2003 if (cmd_hi == 0) { 2004 dev_warn(&dev->dev, "Firmware left e100 interrupts enabled; disabling\n"); 2005 writeb(1, csr + 3); 2006 } 2007 2008 iounmap(csr); 2009 } 2010 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, 2011 PCI_CLASS_NETWORK_ETHERNET, 8, quirk_e100_interrupt); 2012 2013 /* 2014 * The 82575 and 82598 may experience data corruption issues when transitioning 2015 * out of L0S. To prevent this we need to disable L0S on the pci-e link 2016 */ 2017 static void quirk_disable_aspm_l0s(struct pci_dev *dev) 2018 { 2019 dev_info(&dev->dev, "Disabling L0s\n"); 2020 pci_disable_link_state(dev, PCIE_LINK_STATE_L0S); 2021 } 2022 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10a7, quirk_disable_aspm_l0s); 2023 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10a9, quirk_disable_aspm_l0s); 2024 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10b6, quirk_disable_aspm_l0s); 2025 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c6, quirk_disable_aspm_l0s); 2026 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c7, quirk_disable_aspm_l0s); 2027 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c8, quirk_disable_aspm_l0s); 2028 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10d6, quirk_disable_aspm_l0s); 2029 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10db, quirk_disable_aspm_l0s); 2030 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10dd, quirk_disable_aspm_l0s); 2031 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10e1, quirk_disable_aspm_l0s); 2032 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10ec, quirk_disable_aspm_l0s); 2033 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f1, quirk_disable_aspm_l0s); 2034 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f4, quirk_disable_aspm_l0s); 2035 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1508, quirk_disable_aspm_l0s); 2036 2037 static void fixup_rev1_53c810(struct pci_dev *dev) 2038 { 2039 u32 class = dev->class; 2040 2041 /* 2042 * rev 1 ncr53c810 chips don't set the class at all which means 2043 * they don't get their resources remapped. Fix that here. 2044 */ 2045 if (class) 2046 return; 2047 2048 dev->class = PCI_CLASS_STORAGE_SCSI << 8; 2049 dev_info(&dev->dev, "NCR 53c810 rev 1 PCI class overridden (%#08x -> %#08x)\n", 2050 class, dev->class); 2051 } 2052 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810); 2053 2054 /* Enable 1k I/O space granularity on the Intel P64H2 */ 2055 static void quirk_p64h2_1k_io(struct pci_dev *dev) 2056 { 2057 u16 en1k; 2058 2059 pci_read_config_word(dev, 0x40, &en1k); 2060 2061 if (en1k & 0x200) { 2062 dev_info(&dev->dev, "Enable I/O Space to 1KB granularity\n"); 2063 dev->io_window_1k = 1; 2064 } 2065 } 2066 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x1460, quirk_p64h2_1k_io); 2067 2068 /* Under some circumstances, AER is not linked with extended capabilities. 2069 * Force it to be linked by setting the corresponding control bit in the 2070 * config space. 2071 */ 2072 static void quirk_nvidia_ck804_pcie_aer_ext_cap(struct pci_dev *dev) 2073 { 2074 uint8_t b; 2075 if (pci_read_config_byte(dev, 0xf41, &b) == 0) { 2076 if (!(b & 0x20)) { 2077 pci_write_config_byte(dev, 0xf41, b | 0x20); 2078 dev_info(&dev->dev, "Linking AER extended capability\n"); 2079 } 2080 } 2081 } 2082 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE, 2083 quirk_nvidia_ck804_pcie_aer_ext_cap); 2084 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE, 2085 quirk_nvidia_ck804_pcie_aer_ext_cap); 2086 2087 static void quirk_via_cx700_pci_parking_caching(struct pci_dev *dev) 2088 { 2089 /* 2090 * Disable PCI Bus Parking and PCI Master read caching on CX700 2091 * which causes unspecified timing errors with a VT6212L on the PCI 2092 * bus leading to USB2.0 packet loss. 2093 * 2094 * This quirk is only enabled if a second (on the external PCI bus) 2095 * VT6212L is found -- the CX700 core itself also contains a USB 2096 * host controller with the same PCI ID as the VT6212L. 2097 */ 2098 2099 /* Count VT6212L instances */ 2100 struct pci_dev *p = pci_get_device(PCI_VENDOR_ID_VIA, 2101 PCI_DEVICE_ID_VIA_8235_USB_2, NULL); 2102 uint8_t b; 2103 2104 /* p should contain the first (internal) VT6212L -- see if we have 2105 an external one by searching again */ 2106 p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235_USB_2, p); 2107 if (!p) 2108 return; 2109 pci_dev_put(p); 2110 2111 if (pci_read_config_byte(dev, 0x76, &b) == 0) { 2112 if (b & 0x40) { 2113 /* Turn off PCI Bus Parking */ 2114 pci_write_config_byte(dev, 0x76, b ^ 0x40); 2115 2116 dev_info(&dev->dev, "Disabling VIA CX700 PCI parking\n"); 2117 } 2118 } 2119 2120 if (pci_read_config_byte(dev, 0x72, &b) == 0) { 2121 if (b != 0) { 2122 /* Turn off PCI Master read caching */ 2123 pci_write_config_byte(dev, 0x72, 0x0); 2124 2125 /* Set PCI Master Bus time-out to "1x16 PCLK" */ 2126 pci_write_config_byte(dev, 0x75, 0x1); 2127 2128 /* Disable "Read FIFO Timer" */ 2129 pci_write_config_byte(dev, 0x77, 0x0); 2130 2131 dev_info(&dev->dev, "Disabling VIA CX700 PCI caching\n"); 2132 } 2133 } 2134 } 2135 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0x324e, quirk_via_cx700_pci_parking_caching); 2136 2137 /* 2138 * If a device follows the VPD format spec, the PCI core will not read or 2139 * write past the VPD End Tag. But some vendors do not follow the VPD 2140 * format spec, so we can't tell how much data is safe to access. Devices 2141 * may behave unpredictably if we access too much. Blacklist these devices 2142 * so we don't touch VPD at all. 2143 */ 2144 static void quirk_blacklist_vpd(struct pci_dev *dev) 2145 { 2146 if (dev->vpd) { 2147 dev->vpd->len = 0; 2148 dev_warn(&dev->dev, FW_BUG "VPD access disabled\n"); 2149 } 2150 } 2151 2152 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_LSI_LOGIC, 0x0060, quirk_blacklist_vpd); 2153 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_LSI_LOGIC, 0x007c, quirk_blacklist_vpd); 2154 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_LSI_LOGIC, 0x0413, quirk_blacklist_vpd); 2155 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_LSI_LOGIC, 0x0078, quirk_blacklist_vpd); 2156 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_LSI_LOGIC, 0x0079, quirk_blacklist_vpd); 2157 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_LSI_LOGIC, 0x0073, quirk_blacklist_vpd); 2158 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_LSI_LOGIC, 0x0071, quirk_blacklist_vpd); 2159 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_LSI_LOGIC, 0x005b, quirk_blacklist_vpd); 2160 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_LSI_LOGIC, 0x002f, quirk_blacklist_vpd); 2161 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_LSI_LOGIC, 0x005d, quirk_blacklist_vpd); 2162 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_LSI_LOGIC, 0x005f, quirk_blacklist_vpd); 2163 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, PCI_ANY_ID, 2164 quirk_blacklist_vpd); 2165 2166 /* 2167 * For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the 2168 * VPD end tag will hang the device. This problem was initially 2169 * observed when a vpd entry was created in sysfs 2170 * ('/sys/bus/pci/devices/<id>/vpd'). A read to this sysfs entry 2171 * will dump 32k of data. Reading a full 32k will cause an access 2172 * beyond the VPD end tag causing the device to hang. Once the device 2173 * is hung, the bnx2 driver will not be able to reset the device. 2174 * We believe that it is legal to read beyond the end tag and 2175 * therefore the solution is to limit the read/write length. 2176 */ 2177 static void quirk_brcm_570x_limit_vpd(struct pci_dev *dev) 2178 { 2179 /* 2180 * Only disable the VPD capability for 5706, 5706S, 5708, 2181 * 5708S and 5709 rev. A 2182 */ 2183 if ((dev->device == PCI_DEVICE_ID_NX2_5706) || 2184 (dev->device == PCI_DEVICE_ID_NX2_5706S) || 2185 (dev->device == PCI_DEVICE_ID_NX2_5708) || 2186 (dev->device == PCI_DEVICE_ID_NX2_5708S) || 2187 ((dev->device == PCI_DEVICE_ID_NX2_5709) && 2188 (dev->revision & 0xf0) == 0x0)) { 2189 if (dev->vpd) 2190 dev->vpd->len = 0x80; 2191 } 2192 } 2193 2194 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 2195 PCI_DEVICE_ID_NX2_5706, 2196 quirk_brcm_570x_limit_vpd); 2197 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 2198 PCI_DEVICE_ID_NX2_5706S, 2199 quirk_brcm_570x_limit_vpd); 2200 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 2201 PCI_DEVICE_ID_NX2_5708, 2202 quirk_brcm_570x_limit_vpd); 2203 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 2204 PCI_DEVICE_ID_NX2_5708S, 2205 quirk_brcm_570x_limit_vpd); 2206 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 2207 PCI_DEVICE_ID_NX2_5709, 2208 quirk_brcm_570x_limit_vpd); 2209 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 2210 PCI_DEVICE_ID_NX2_5709S, 2211 quirk_brcm_570x_limit_vpd); 2212 2213 static void quirk_brcm_5719_limit_mrrs(struct pci_dev *dev) 2214 { 2215 u32 rev; 2216 2217 pci_read_config_dword(dev, 0xf4, &rev); 2218 2219 /* Only CAP the MRRS if the device is a 5719 A0 */ 2220 if (rev == 0x05719000) { 2221 int readrq = pcie_get_readrq(dev); 2222 if (readrq > 2048) 2223 pcie_set_readrq(dev, 2048); 2224 } 2225 } 2226 2227 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_BROADCOM, 2228 PCI_DEVICE_ID_TIGON3_5719, 2229 quirk_brcm_5719_limit_mrrs); 2230 2231 /* Originally in EDAC sources for i82875P: 2232 * Intel tells BIOS developers to hide device 6 which 2233 * configures the overflow device access containing 2234 * the DRBs - this is where we expose device 6. 2235 * http://www.x86-secret.com/articles/tweak/pat/patsecrets-2.htm 2236 */ 2237 static void quirk_unhide_mch_dev6(struct pci_dev *dev) 2238 { 2239 u8 reg; 2240 2241 if (pci_read_config_byte(dev, 0xF4, ®) == 0 && !(reg & 0x02)) { 2242 dev_info(&dev->dev, "Enabling MCH 'Overflow' Device\n"); 2243 pci_write_config_byte(dev, 0xF4, reg | 0x02); 2244 } 2245 } 2246 2247 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB, 2248 quirk_unhide_mch_dev6); 2249 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82875_HB, 2250 quirk_unhide_mch_dev6); 2251 2252 #ifdef CONFIG_TILEPRO 2253 /* 2254 * The Tilera TILEmpower tilepro platform needs to set the link speed 2255 * to 2.5GT(Giga-Transfers)/s (Gen 1). The default link speed 2256 * setting is 5GT/s (Gen 2). 0x98 is the Link Control2 PCIe 2257 * capability register of the PEX8624 PCIe switch. The switch 2258 * supports link speed auto negotiation, but falsely sets 2259 * the link speed to 5GT/s. 2260 */ 2261 static void quirk_tile_plx_gen1(struct pci_dev *dev) 2262 { 2263 if (tile_plx_gen1) { 2264 pci_write_config_dword(dev, 0x98, 0x1); 2265 mdelay(50); 2266 } 2267 } 2268 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PLX, 0x8624, quirk_tile_plx_gen1); 2269 #endif /* CONFIG_TILEPRO */ 2270 2271 #ifdef CONFIG_PCI_MSI 2272 /* Some chipsets do not support MSI. We cannot easily rely on setting 2273 * PCI_BUS_FLAGS_NO_MSI in its bus flags because there are actually 2274 * some other buses controlled by the chipset even if Linux is not 2275 * aware of it. Instead of setting the flag on all buses in the 2276 * machine, simply disable MSI globally. 2277 */ 2278 static void quirk_disable_all_msi(struct pci_dev *dev) 2279 { 2280 pci_no_msi(); 2281 dev_warn(&dev->dev, "MSI quirk detected; MSI disabled\n"); 2282 } 2283 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_GCNB_LE, quirk_disable_all_msi); 2284 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS400_200, quirk_disable_all_msi); 2285 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS480, quirk_disable_all_msi); 2286 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3336, quirk_disable_all_msi); 2287 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3351, quirk_disable_all_msi); 2288 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3364, quirk_disable_all_msi); 2289 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8380_0, quirk_disable_all_msi); 2290 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, 0x0761, quirk_disable_all_msi); 2291 2292 /* Disable MSI on chipsets that are known to not support it */ 2293 static void quirk_disable_msi(struct pci_dev *dev) 2294 { 2295 if (dev->subordinate) { 2296 dev_warn(&dev->dev, "MSI quirk detected; subordinate MSI disabled\n"); 2297 dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI; 2298 } 2299 } 2300 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_msi); 2301 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0xa238, quirk_disable_msi); 2302 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x5a3f, quirk_disable_msi); 2303 2304 /* 2305 * The APC bridge device in AMD 780 family northbridges has some random 2306 * OEM subsystem ID in its vendor ID register (erratum 18), so instead 2307 * we use the possible vendor/device IDs of the host bridge for the 2308 * declared quirk, and search for the APC bridge by slot number. 2309 */ 2310 static void quirk_amd_780_apc_msi(struct pci_dev *host_bridge) 2311 { 2312 struct pci_dev *apc_bridge; 2313 2314 apc_bridge = pci_get_slot(host_bridge->bus, PCI_DEVFN(1, 0)); 2315 if (apc_bridge) { 2316 if (apc_bridge->device == 0x9602) 2317 quirk_disable_msi(apc_bridge); 2318 pci_dev_put(apc_bridge); 2319 } 2320 } 2321 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x9600, quirk_amd_780_apc_msi); 2322 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x9601, quirk_amd_780_apc_msi); 2323 2324 /* Go through the list of Hypertransport capabilities and 2325 * return 1 if a HT MSI capability is found and enabled */ 2326 static int msi_ht_cap_enabled(struct pci_dev *dev) 2327 { 2328 int pos, ttl = PCI_FIND_CAP_TTL; 2329 2330 pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); 2331 while (pos && ttl--) { 2332 u8 flags; 2333 2334 if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, 2335 &flags) == 0) { 2336 dev_info(&dev->dev, "Found %s HT MSI Mapping\n", 2337 flags & HT_MSI_FLAGS_ENABLE ? 2338 "enabled" : "disabled"); 2339 return (flags & HT_MSI_FLAGS_ENABLE) != 0; 2340 } 2341 2342 pos = pci_find_next_ht_capability(dev, pos, 2343 HT_CAPTYPE_MSI_MAPPING); 2344 } 2345 return 0; 2346 } 2347 2348 /* Check the hypertransport MSI mapping to know whether MSI is enabled or not */ 2349 static void quirk_msi_ht_cap(struct pci_dev *dev) 2350 { 2351 if (dev->subordinate && !msi_ht_cap_enabled(dev)) { 2352 dev_warn(&dev->dev, "MSI quirk detected; subordinate MSI disabled\n"); 2353 dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI; 2354 } 2355 } 2356 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT2000_PCIE, 2357 quirk_msi_ht_cap); 2358 2359 /* The nVidia CK804 chipset may have 2 HT MSI mappings. 2360 * MSI are supported if the MSI capability set in any of these mappings. 2361 */ 2362 static void quirk_nvidia_ck804_msi_ht_cap(struct pci_dev *dev) 2363 { 2364 struct pci_dev *pdev; 2365 2366 if (!dev->subordinate) 2367 return; 2368 2369 /* check HT MSI cap on this chipset and the root one. 2370 * a single one having MSI is enough to be sure that MSI are supported. 2371 */ 2372 pdev = pci_get_slot(dev->bus, 0); 2373 if (!pdev) 2374 return; 2375 if (!msi_ht_cap_enabled(dev) && !msi_ht_cap_enabled(pdev)) { 2376 dev_warn(&dev->dev, "MSI quirk detected; subordinate MSI disabled\n"); 2377 dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI; 2378 } 2379 pci_dev_put(pdev); 2380 } 2381 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE, 2382 quirk_nvidia_ck804_msi_ht_cap); 2383 2384 /* Force enable MSI mapping capability on HT bridges */ 2385 static void ht_enable_msi_mapping(struct pci_dev *dev) 2386 { 2387 int pos, ttl = PCI_FIND_CAP_TTL; 2388 2389 pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); 2390 while (pos && ttl--) { 2391 u8 flags; 2392 2393 if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, 2394 &flags) == 0) { 2395 dev_info(&dev->dev, "Enabling HT MSI Mapping\n"); 2396 2397 pci_write_config_byte(dev, pos + HT_MSI_FLAGS, 2398 flags | HT_MSI_FLAGS_ENABLE); 2399 } 2400 pos = pci_find_next_ht_capability(dev, pos, 2401 HT_CAPTYPE_MSI_MAPPING); 2402 } 2403 } 2404 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SERVERWORKS, 2405 PCI_DEVICE_ID_SERVERWORKS_HT1000_PXB, 2406 ht_enable_msi_mapping); 2407 2408 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, 2409 ht_enable_msi_mapping); 2410 2411 /* The P5N32-SLI motherboards from Asus have a problem with msi 2412 * for the MCP55 NIC. It is not yet determined whether the msi problem 2413 * also affects other devices. As for now, turn off msi for this device. 2414 */ 2415 static void nvenet_msi_disable(struct pci_dev *dev) 2416 { 2417 const char *board_name = dmi_get_system_info(DMI_BOARD_NAME); 2418 2419 if (board_name && 2420 (strstr(board_name, "P5N32-SLI PREMIUM") || 2421 strstr(board_name, "P5N32-E SLI"))) { 2422 dev_info(&dev->dev, "Disabling msi for MCP55 NIC on P5N32-SLI\n"); 2423 dev->no_msi = 1; 2424 } 2425 } 2426 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA, 2427 PCI_DEVICE_ID_NVIDIA_NVENET_15, 2428 nvenet_msi_disable); 2429 2430 /* 2431 * Some versions of the MCP55 bridge from Nvidia have a legacy IRQ routing 2432 * config register. This register controls the routing of legacy 2433 * interrupts from devices that route through the MCP55. If this register 2434 * is misprogrammed, interrupts are only sent to the BSP, unlike 2435 * conventional systems where the IRQ is broadcast to all online CPUs. Not 2436 * having this register set properly prevents kdump from booting up 2437 * properly, so let's make sure that we have it set correctly. 2438 * Note that this is an undocumented register. 2439 */ 2440 static void nvbridge_check_legacy_irq_routing(struct pci_dev *dev) 2441 { 2442 u32 cfg; 2443 2444 if (!pci_find_capability(dev, PCI_CAP_ID_HT)) 2445 return; 2446 2447 pci_read_config_dword(dev, 0x74, &cfg); 2448 2449 if (cfg & ((1 << 2) | (1 << 15))) { 2450 printk(KERN_INFO "Rewriting irq routing register on MCP55\n"); 2451 cfg &= ~((1 << 2) | (1 << 15)); 2452 pci_write_config_dword(dev, 0x74, cfg); 2453 } 2454 } 2455 2456 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA, 2457 PCI_DEVICE_ID_NVIDIA_MCP55_BRIDGE_V0, 2458 nvbridge_check_legacy_irq_routing); 2459 2460 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA, 2461 PCI_DEVICE_ID_NVIDIA_MCP55_BRIDGE_V4, 2462 nvbridge_check_legacy_irq_routing); 2463 2464 static int ht_check_msi_mapping(struct pci_dev *dev) 2465 { 2466 int pos, ttl = PCI_FIND_CAP_TTL; 2467 int found = 0; 2468 2469 /* check if there is HT MSI cap or enabled on this device */ 2470 pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); 2471 while (pos && ttl--) { 2472 u8 flags; 2473 2474 if (found < 1) 2475 found = 1; 2476 if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, 2477 &flags) == 0) { 2478 if (flags & HT_MSI_FLAGS_ENABLE) { 2479 if (found < 2) { 2480 found = 2; 2481 break; 2482 } 2483 } 2484 } 2485 pos = pci_find_next_ht_capability(dev, pos, 2486 HT_CAPTYPE_MSI_MAPPING); 2487 } 2488 2489 return found; 2490 } 2491 2492 static int host_bridge_with_leaf(struct pci_dev *host_bridge) 2493 { 2494 struct pci_dev *dev; 2495 int pos; 2496 int i, dev_no; 2497 int found = 0; 2498 2499 dev_no = host_bridge->devfn >> 3; 2500 for (i = dev_no + 1; i < 0x20; i++) { 2501 dev = pci_get_slot(host_bridge->bus, PCI_DEVFN(i, 0)); 2502 if (!dev) 2503 continue; 2504 2505 /* found next host bridge ?*/ 2506 pos = pci_find_ht_capability(dev, HT_CAPTYPE_SLAVE); 2507 if (pos != 0) { 2508 pci_dev_put(dev); 2509 break; 2510 } 2511 2512 if (ht_check_msi_mapping(dev)) { 2513 found = 1; 2514 pci_dev_put(dev); 2515 break; 2516 } 2517 pci_dev_put(dev); 2518 } 2519 2520 return found; 2521 } 2522 2523 #define PCI_HT_CAP_SLAVE_CTRL0 4 /* link control */ 2524 #define PCI_HT_CAP_SLAVE_CTRL1 8 /* link control to */ 2525 2526 static int is_end_of_ht_chain(struct pci_dev *dev) 2527 { 2528 int pos, ctrl_off; 2529 int end = 0; 2530 u16 flags, ctrl; 2531 2532 pos = pci_find_ht_capability(dev, HT_CAPTYPE_SLAVE); 2533 2534 if (!pos) 2535 goto out; 2536 2537 pci_read_config_word(dev, pos + PCI_CAP_FLAGS, &flags); 2538 2539 ctrl_off = ((flags >> 10) & 1) ? 2540 PCI_HT_CAP_SLAVE_CTRL0 : PCI_HT_CAP_SLAVE_CTRL1; 2541 pci_read_config_word(dev, pos + ctrl_off, &ctrl); 2542 2543 if (ctrl & (1 << 6)) 2544 end = 1; 2545 2546 out: 2547 return end; 2548 } 2549 2550 static void nv_ht_enable_msi_mapping(struct pci_dev *dev) 2551 { 2552 struct pci_dev *host_bridge; 2553 int pos; 2554 int i, dev_no; 2555 int found = 0; 2556 2557 dev_no = dev->devfn >> 3; 2558 for (i = dev_no; i >= 0; i--) { 2559 host_bridge = pci_get_slot(dev->bus, PCI_DEVFN(i, 0)); 2560 if (!host_bridge) 2561 continue; 2562 2563 pos = pci_find_ht_capability(host_bridge, HT_CAPTYPE_SLAVE); 2564 if (pos != 0) { 2565 found = 1; 2566 break; 2567 } 2568 pci_dev_put(host_bridge); 2569 } 2570 2571 if (!found) 2572 return; 2573 2574 /* don't enable end_device/host_bridge with leaf directly here */ 2575 if (host_bridge == dev && is_end_of_ht_chain(host_bridge) && 2576 host_bridge_with_leaf(host_bridge)) 2577 goto out; 2578 2579 /* root did that ! */ 2580 if (msi_ht_cap_enabled(host_bridge)) 2581 goto out; 2582 2583 ht_enable_msi_mapping(dev); 2584 2585 out: 2586 pci_dev_put(host_bridge); 2587 } 2588 2589 static void ht_disable_msi_mapping(struct pci_dev *dev) 2590 { 2591 int pos, ttl = PCI_FIND_CAP_TTL; 2592 2593 pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); 2594 while (pos && ttl--) { 2595 u8 flags; 2596 2597 if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, 2598 &flags) == 0) { 2599 dev_info(&dev->dev, "Disabling HT MSI Mapping\n"); 2600 2601 pci_write_config_byte(dev, pos + HT_MSI_FLAGS, 2602 flags & ~HT_MSI_FLAGS_ENABLE); 2603 } 2604 pos = pci_find_next_ht_capability(dev, pos, 2605 HT_CAPTYPE_MSI_MAPPING); 2606 } 2607 } 2608 2609 static void __nv_msi_ht_cap_quirk(struct pci_dev *dev, int all) 2610 { 2611 struct pci_dev *host_bridge; 2612 int pos; 2613 int found; 2614 2615 if (!pci_msi_enabled()) 2616 return; 2617 2618 /* check if there is HT MSI cap or enabled on this device */ 2619 found = ht_check_msi_mapping(dev); 2620 2621 /* no HT MSI CAP */ 2622 if (found == 0) 2623 return; 2624 2625 /* 2626 * HT MSI mapping should be disabled on devices that are below 2627 * a non-Hypertransport host bridge. Locate the host bridge... 2628 */ 2629 host_bridge = pci_get_bus_and_slot(0, PCI_DEVFN(0, 0)); 2630 if (host_bridge == NULL) { 2631 dev_warn(&dev->dev, "nv_msi_ht_cap_quirk didn't locate host bridge\n"); 2632 return; 2633 } 2634 2635 pos = pci_find_ht_capability(host_bridge, HT_CAPTYPE_SLAVE); 2636 if (pos != 0) { 2637 /* Host bridge is to HT */ 2638 if (found == 1) { 2639 /* it is not enabled, try to enable it */ 2640 if (all) 2641 ht_enable_msi_mapping(dev); 2642 else 2643 nv_ht_enable_msi_mapping(dev); 2644 } 2645 goto out; 2646 } 2647 2648 /* HT MSI is not enabled */ 2649 if (found == 1) 2650 goto out; 2651 2652 /* Host bridge is not to HT, disable HT MSI mapping on this device */ 2653 ht_disable_msi_mapping(dev); 2654 2655 out: 2656 pci_dev_put(host_bridge); 2657 } 2658 2659 static void nv_msi_ht_cap_quirk_all(struct pci_dev *dev) 2660 { 2661 return __nv_msi_ht_cap_quirk(dev, 1); 2662 } 2663 2664 static void nv_msi_ht_cap_quirk_leaf(struct pci_dev *dev) 2665 { 2666 return __nv_msi_ht_cap_quirk(dev, 0); 2667 } 2668 2669 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk_leaf); 2670 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk_leaf); 2671 2672 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all); 2673 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all); 2674 2675 static void quirk_msi_intx_disable_bug(struct pci_dev *dev) 2676 { 2677 dev->dev_flags |= PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG; 2678 } 2679 static void quirk_msi_intx_disable_ati_bug(struct pci_dev *dev) 2680 { 2681 struct pci_dev *p; 2682 2683 /* SB700 MSI issue will be fixed at HW level from revision A21, 2684 * we need check PCI REVISION ID of SMBus controller to get SB700 2685 * revision. 2686 */ 2687 p = pci_get_device(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SBX00_SMBUS, 2688 NULL); 2689 if (!p) 2690 return; 2691 2692 if ((p->revision < 0x3B) && (p->revision >= 0x30)) 2693 dev->dev_flags |= PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG; 2694 pci_dev_put(p); 2695 } 2696 static void quirk_msi_intx_disable_qca_bug(struct pci_dev *dev) 2697 { 2698 /* AR816X/AR817X/E210X MSI is fixed at HW level from revision 0x18 */ 2699 if (dev->revision < 0x18) { 2700 dev_info(&dev->dev, "set MSI_INTX_DISABLE_BUG flag\n"); 2701 dev->dev_flags |= PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG; 2702 } 2703 } 2704 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 2705 PCI_DEVICE_ID_TIGON3_5780, 2706 quirk_msi_intx_disable_bug); 2707 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 2708 PCI_DEVICE_ID_TIGON3_5780S, 2709 quirk_msi_intx_disable_bug); 2710 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 2711 PCI_DEVICE_ID_TIGON3_5714, 2712 quirk_msi_intx_disable_bug); 2713 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 2714 PCI_DEVICE_ID_TIGON3_5714S, 2715 quirk_msi_intx_disable_bug); 2716 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 2717 PCI_DEVICE_ID_TIGON3_5715, 2718 quirk_msi_intx_disable_bug); 2719 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 2720 PCI_DEVICE_ID_TIGON3_5715S, 2721 quirk_msi_intx_disable_bug); 2722 2723 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4390, 2724 quirk_msi_intx_disable_ati_bug); 2725 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4391, 2726 quirk_msi_intx_disable_ati_bug); 2727 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4392, 2728 quirk_msi_intx_disable_ati_bug); 2729 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4393, 2730 quirk_msi_intx_disable_ati_bug); 2731 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4394, 2732 quirk_msi_intx_disable_ati_bug); 2733 2734 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4373, 2735 quirk_msi_intx_disable_bug); 2736 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4374, 2737 quirk_msi_intx_disable_bug); 2738 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4375, 2739 quirk_msi_intx_disable_bug); 2740 2741 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1062, 2742 quirk_msi_intx_disable_bug); 2743 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1063, 2744 quirk_msi_intx_disable_bug); 2745 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x2060, 2746 quirk_msi_intx_disable_bug); 2747 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x2062, 2748 quirk_msi_intx_disable_bug); 2749 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1073, 2750 quirk_msi_intx_disable_bug); 2751 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1083, 2752 quirk_msi_intx_disable_bug); 2753 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1090, 2754 quirk_msi_intx_disable_qca_bug); 2755 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1091, 2756 quirk_msi_intx_disable_qca_bug); 2757 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x10a0, 2758 quirk_msi_intx_disable_qca_bug); 2759 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x10a1, 2760 quirk_msi_intx_disable_qca_bug); 2761 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0xe091, 2762 quirk_msi_intx_disable_qca_bug); 2763 #endif /* CONFIG_PCI_MSI */ 2764 2765 /* Allow manual resource allocation for PCI hotplug bridges 2766 * via pci=hpmemsize=nnM and pci=hpiosize=nnM parameters. For 2767 * some PCI-PCI hotplug bridges, like PLX 6254 (former HINT HB6), 2768 * kernel fails to allocate resources when hotplug device is 2769 * inserted and PCI bus is rescanned. 2770 */ 2771 static void quirk_hotplug_bridge(struct pci_dev *dev) 2772 { 2773 dev->is_hotplug_bridge = 1; 2774 } 2775 2776 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_HINT, 0x0020, quirk_hotplug_bridge); 2777 2778 /* 2779 * This is a quirk for the Ricoh MMC controller found as a part of 2780 * some mulifunction chips. 2781 2782 * This is very similar and based on the ricoh_mmc driver written by 2783 * Philip Langdale. Thank you for these magic sequences. 2784 * 2785 * These chips implement the four main memory card controllers (SD, MMC, MS, xD) 2786 * and one or both of cardbus or firewire. 2787 * 2788 * It happens that they implement SD and MMC 2789 * support as separate controllers (and PCI functions). The linux SDHCI 2790 * driver supports MMC cards but the chip detects MMC cards in hardware 2791 * and directs them to the MMC controller - so the SDHCI driver never sees 2792 * them. 2793 * 2794 * To get around this, we must disable the useless MMC controller. 2795 * At that point, the SDHCI controller will start seeing them 2796 * It seems to be the case that the relevant PCI registers to deactivate the 2797 * MMC controller live on PCI function 0, which might be the cardbus controller 2798 * or the firewire controller, depending on the particular chip in question 2799 * 2800 * This has to be done early, because as soon as we disable the MMC controller 2801 * other pci functions shift up one level, e.g. function #2 becomes function 2802 * #1, and this will confuse the pci core. 2803 */ 2804 2805 #ifdef CONFIG_MMC_RICOH_MMC 2806 static void ricoh_mmc_fixup_rl5c476(struct pci_dev *dev) 2807 { 2808 /* disable via cardbus interface */ 2809 u8 write_enable; 2810 u8 write_target; 2811 u8 disable; 2812 2813 /* disable must be done via function #0 */ 2814 if (PCI_FUNC(dev->devfn)) 2815 return; 2816 2817 pci_read_config_byte(dev, 0xB7, &disable); 2818 if (disable & 0x02) 2819 return; 2820 2821 pci_read_config_byte(dev, 0x8E, &write_enable); 2822 pci_write_config_byte(dev, 0x8E, 0xAA); 2823 pci_read_config_byte(dev, 0x8D, &write_target); 2824 pci_write_config_byte(dev, 0x8D, 0xB7); 2825 pci_write_config_byte(dev, 0xB7, disable | 0x02); 2826 pci_write_config_byte(dev, 0x8E, write_enable); 2827 pci_write_config_byte(dev, 0x8D, write_target); 2828 2829 dev_notice(&dev->dev, "proprietary Ricoh MMC controller disabled (via cardbus function)\n"); 2830 dev_notice(&dev->dev, "MMC cards are now supported by standard SDHCI controller\n"); 2831 } 2832 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, ricoh_mmc_fixup_rl5c476); 2833 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, ricoh_mmc_fixup_rl5c476); 2834 2835 static void ricoh_mmc_fixup_r5c832(struct pci_dev *dev) 2836 { 2837 /* disable via firewire interface */ 2838 u8 write_enable; 2839 u8 disable; 2840 2841 /* disable must be done via function #0 */ 2842 if (PCI_FUNC(dev->devfn)) 2843 return; 2844 /* 2845 * RICOH 0xe822 and 0xe823 SD/MMC card readers fail to recognize 2846 * certain types of SD/MMC cards. Lowering the SD base 2847 * clock frequency from 200Mhz to 50Mhz fixes this issue. 2848 * 2849 * 0x150 - SD2.0 mode enable for changing base clock 2850 * frequency to 50Mhz 2851 * 0xe1 - Base clock frequency 2852 * 0x32 - 50Mhz new clock frequency 2853 * 0xf9 - Key register for 0x150 2854 * 0xfc - key register for 0xe1 2855 */ 2856 if (dev->device == PCI_DEVICE_ID_RICOH_R5CE822 || 2857 dev->device == PCI_DEVICE_ID_RICOH_R5CE823) { 2858 pci_write_config_byte(dev, 0xf9, 0xfc); 2859 pci_write_config_byte(dev, 0x150, 0x10); 2860 pci_write_config_byte(dev, 0xf9, 0x00); 2861 pci_write_config_byte(dev, 0xfc, 0x01); 2862 pci_write_config_byte(dev, 0xe1, 0x32); 2863 pci_write_config_byte(dev, 0xfc, 0x00); 2864 2865 dev_notice(&dev->dev, "MMC controller base frequency changed to 50Mhz.\n"); 2866 } 2867 2868 pci_read_config_byte(dev, 0xCB, &disable); 2869 2870 if (disable & 0x02) 2871 return; 2872 2873 pci_read_config_byte(dev, 0xCA, &write_enable); 2874 pci_write_config_byte(dev, 0xCA, 0x57); 2875 pci_write_config_byte(dev, 0xCB, disable | 0x02); 2876 pci_write_config_byte(dev, 0xCA, write_enable); 2877 2878 dev_notice(&dev->dev, "proprietary Ricoh MMC controller disabled (via firewire function)\n"); 2879 dev_notice(&dev->dev, "MMC cards are now supported by standard SDHCI controller\n"); 2880 2881 } 2882 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832); 2883 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832); 2884 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE822, ricoh_mmc_fixup_r5c832); 2885 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE822, ricoh_mmc_fixup_r5c832); 2886 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE823, ricoh_mmc_fixup_r5c832); 2887 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE823, ricoh_mmc_fixup_r5c832); 2888 #endif /*CONFIG_MMC_RICOH_MMC*/ 2889 2890 #ifdef CONFIG_DMAR_TABLE 2891 #define VTUNCERRMSK_REG 0x1ac 2892 #define VTD_MSK_SPEC_ERRORS (1 << 31) 2893 /* 2894 * This is a quirk for masking vt-d spec defined errors to platform error 2895 * handling logic. With out this, platforms using Intel 7500, 5500 chipsets 2896 * (and the derivative chipsets like X58 etc) seem to generate NMI/SMI (based 2897 * on the RAS config settings of the platform) when a vt-d fault happens. 2898 * The resulting SMI caused the system to hang. 2899 * 2900 * VT-d spec related errors are already handled by the VT-d OS code, so no 2901 * need to report the same error through other channels. 2902 */ 2903 static void vtd_mask_spec_errors(struct pci_dev *dev) 2904 { 2905 u32 word; 2906 2907 pci_read_config_dword(dev, VTUNCERRMSK_REG, &word); 2908 pci_write_config_dword(dev, VTUNCERRMSK_REG, word | VTD_MSK_SPEC_ERRORS); 2909 } 2910 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x342e, vtd_mask_spec_errors); 2911 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x3c28, vtd_mask_spec_errors); 2912 #endif 2913 2914 static void fixup_ti816x_class(struct pci_dev *dev) 2915 { 2916 u32 class = dev->class; 2917 2918 /* TI 816x devices do not have class code set when in PCIe boot mode */ 2919 dev->class = PCI_CLASS_MULTIMEDIA_VIDEO << 8; 2920 dev_info(&dev->dev, "PCI class overridden (%#08x -> %#08x)\n", 2921 class, dev->class); 2922 } 2923 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_TI, 0xb800, 2924 PCI_CLASS_NOT_DEFINED, 8, fixup_ti816x_class); 2925 2926 /* Some PCIe devices do not work reliably with the claimed maximum 2927 * payload size supported. 2928 */ 2929 static void fixup_mpss_256(struct pci_dev *dev) 2930 { 2931 dev->pcie_mpss = 1; /* 256 bytes */ 2932 } 2933 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SOLARFLARE, 2934 PCI_DEVICE_ID_SOLARFLARE_SFC4000A_0, fixup_mpss_256); 2935 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SOLARFLARE, 2936 PCI_DEVICE_ID_SOLARFLARE_SFC4000A_1, fixup_mpss_256); 2937 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SOLARFLARE, 2938 PCI_DEVICE_ID_SOLARFLARE_SFC4000B, fixup_mpss_256); 2939 2940 /* Intel 5000 and 5100 Memory controllers have an errata with read completion 2941 * coalescing (which is enabled by default on some BIOSes) and MPS of 256B. 2942 * Since there is no way of knowing what the PCIE MPS on each fabric will be 2943 * until all of the devices are discovered and buses walked, read completion 2944 * coalescing must be disabled. Unfortunately, it cannot be re-enabled because 2945 * it is possible to hotplug a device with MPS of 256B. 2946 */ 2947 static void quirk_intel_mc_errata(struct pci_dev *dev) 2948 { 2949 int err; 2950 u16 rcc; 2951 2952 if (pcie_bus_config == PCIE_BUS_TUNE_OFF || 2953 pcie_bus_config == PCIE_BUS_DEFAULT) 2954 return; 2955 2956 /* Intel errata specifies bits to change but does not say what they are. 2957 * Keeping them magical until such time as the registers and values can 2958 * be explained. 2959 */ 2960 err = pci_read_config_word(dev, 0x48, &rcc); 2961 if (err) { 2962 dev_err(&dev->dev, "Error attempting to read the read completion coalescing register\n"); 2963 return; 2964 } 2965 2966 if (!(rcc & (1 << 10))) 2967 return; 2968 2969 rcc &= ~(1 << 10); 2970 2971 err = pci_write_config_word(dev, 0x48, rcc); 2972 if (err) { 2973 dev_err(&dev->dev, "Error attempting to write the read completion coalescing register\n"); 2974 return; 2975 } 2976 2977 pr_info_once("Read completion coalescing disabled due to hardware errata relating to 256B MPS\n"); 2978 } 2979 /* Intel 5000 series memory controllers and ports 2-7 */ 2980 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25c0, quirk_intel_mc_errata); 2981 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d0, quirk_intel_mc_errata); 2982 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d4, quirk_intel_mc_errata); 2983 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d8, quirk_intel_mc_errata); 2984 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e2, quirk_intel_mc_errata); 2985 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e3, quirk_intel_mc_errata); 2986 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e4, quirk_intel_mc_errata); 2987 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e5, quirk_intel_mc_errata); 2988 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e6, quirk_intel_mc_errata); 2989 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e7, quirk_intel_mc_errata); 2990 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f7, quirk_intel_mc_errata); 2991 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f8, quirk_intel_mc_errata); 2992 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f9, quirk_intel_mc_errata); 2993 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25fa, quirk_intel_mc_errata); 2994 /* Intel 5100 series memory controllers and ports 2-7 */ 2995 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65c0, quirk_intel_mc_errata); 2996 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e2, quirk_intel_mc_errata); 2997 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e3, quirk_intel_mc_errata); 2998 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e4, quirk_intel_mc_errata); 2999 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e5, quirk_intel_mc_errata); 3000 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e6, quirk_intel_mc_errata); 3001 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e7, quirk_intel_mc_errata); 3002 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f7, quirk_intel_mc_errata); 3003 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f8, quirk_intel_mc_errata); 3004 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f9, quirk_intel_mc_errata); 3005 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65fa, quirk_intel_mc_errata); 3006 3007 3008 /* 3009 * Ivytown NTB BAR sizes are misreported by the hardware due to an erratum. To 3010 * work around this, query the size it should be configured to by the device and 3011 * modify the resource end to correspond to this new size. 3012 */ 3013 static void quirk_intel_ntb(struct pci_dev *dev) 3014 { 3015 int rc; 3016 u8 val; 3017 3018 rc = pci_read_config_byte(dev, 0x00D0, &val); 3019 if (rc) 3020 return; 3021 3022 dev->resource[2].end = dev->resource[2].start + ((u64) 1 << val) - 1; 3023 3024 rc = pci_read_config_byte(dev, 0x00D1, &val); 3025 if (rc) 3026 return; 3027 3028 dev->resource[4].end = dev->resource[4].start + ((u64) 1 << val) - 1; 3029 } 3030 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x0e08, quirk_intel_ntb); 3031 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x0e0d, quirk_intel_ntb); 3032 3033 static ktime_t fixup_debug_start(struct pci_dev *dev, 3034 void (*fn)(struct pci_dev *dev)) 3035 { 3036 ktime_t calltime = ktime_set(0, 0); 3037 3038 dev_dbg(&dev->dev, "calling %pF\n", fn); 3039 if (initcall_debug) { 3040 pr_debug("calling %pF @ %i for %s\n", 3041 fn, task_pid_nr(current), dev_name(&dev->dev)); 3042 calltime = ktime_get(); 3043 } 3044 3045 return calltime; 3046 } 3047 3048 static void fixup_debug_report(struct pci_dev *dev, ktime_t calltime, 3049 void (*fn)(struct pci_dev *dev)) 3050 { 3051 ktime_t delta, rettime; 3052 unsigned long long duration; 3053 3054 if (initcall_debug) { 3055 rettime = ktime_get(); 3056 delta = ktime_sub(rettime, calltime); 3057 duration = (unsigned long long) ktime_to_ns(delta) >> 10; 3058 pr_debug("pci fixup %pF returned after %lld usecs for %s\n", 3059 fn, duration, dev_name(&dev->dev)); 3060 } 3061 } 3062 3063 /* 3064 * Some BIOS implementations leave the Intel GPU interrupts enabled, 3065 * even though no one is handling them (f.e. i915 driver is never loaded). 3066 * Additionally the interrupt destination is not set up properly 3067 * and the interrupt ends up -somewhere-. 3068 * 3069 * These spurious interrupts are "sticky" and the kernel disables 3070 * the (shared) interrupt line after 100.000+ generated interrupts. 3071 * 3072 * Fix it by disabling the still enabled interrupts. 3073 * This resolves crashes often seen on monitor unplug. 3074 */ 3075 #define I915_DEIER_REG 0x4400c 3076 static void disable_igfx_irq(struct pci_dev *dev) 3077 { 3078 void __iomem *regs = pci_iomap(dev, 0, 0); 3079 if (regs == NULL) { 3080 dev_warn(&dev->dev, "igfx quirk: Can't iomap PCI device\n"); 3081 return; 3082 } 3083 3084 /* Check if any interrupt line is still enabled */ 3085 if (readl(regs + I915_DEIER_REG) != 0) { 3086 dev_warn(&dev->dev, "BIOS left Intel GPU interrupts enabled; disabling\n"); 3087 3088 writel(0, regs + I915_DEIER_REG); 3089 } 3090 3091 pci_iounmap(dev, regs); 3092 } 3093 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0102, disable_igfx_irq); 3094 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x010a, disable_igfx_irq); 3095 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0152, disable_igfx_irq); 3096 3097 /* 3098 * PCI devices which are on Intel chips can skip the 10ms delay 3099 * before entering D3 mode. 3100 */ 3101 static void quirk_remove_d3_delay(struct pci_dev *dev) 3102 { 3103 dev->d3_delay = 0; 3104 } 3105 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0c00, quirk_remove_d3_delay); 3106 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0412, quirk_remove_d3_delay); 3107 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0c0c, quirk_remove_d3_delay); 3108 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c31, quirk_remove_d3_delay); 3109 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c3a, quirk_remove_d3_delay); 3110 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c3d, quirk_remove_d3_delay); 3111 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c2d, quirk_remove_d3_delay); 3112 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c20, quirk_remove_d3_delay); 3113 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c18, quirk_remove_d3_delay); 3114 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c1c, quirk_remove_d3_delay); 3115 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c26, quirk_remove_d3_delay); 3116 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c4e, quirk_remove_d3_delay); 3117 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c02, quirk_remove_d3_delay); 3118 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c22, quirk_remove_d3_delay); 3119 /* Intel Cherrytrail devices do not need 10ms d3_delay */ 3120 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2280, quirk_remove_d3_delay); 3121 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b0, quirk_remove_d3_delay); 3122 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b8, quirk_remove_d3_delay); 3123 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22d8, quirk_remove_d3_delay); 3124 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22dc, quirk_remove_d3_delay); 3125 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b5, quirk_remove_d3_delay); 3126 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b7, quirk_remove_d3_delay); 3127 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2298, quirk_remove_d3_delay); 3128 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x229c, quirk_remove_d3_delay); 3129 /* 3130 * Some devices may pass our check in pci_intx_mask_supported if 3131 * PCI_COMMAND_INTX_DISABLE works though they actually do not properly 3132 * support this feature. 3133 */ 3134 static void quirk_broken_intx_masking(struct pci_dev *dev) 3135 { 3136 dev->broken_intx_masking = 1; 3137 } 3138 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_CHELSIO, 0x0030, 3139 quirk_broken_intx_masking); 3140 DECLARE_PCI_FIXUP_HEADER(0x1814, 0x0601, /* Ralink RT2800 802.11n PCI */ 3141 quirk_broken_intx_masking); 3142 /* 3143 * Realtek RTL8169 PCI Gigabit Ethernet Controller (rev 10) 3144 * Subsystem: Realtek RTL8169/8110 Family PCI Gigabit Ethernet NIC 3145 * 3146 * RTL8110SC - Fails under PCI device assignment using DisINTx masking. 3147 */ 3148 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_REALTEK, 0x8169, 3149 quirk_broken_intx_masking); 3150 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MELLANOX, PCI_ANY_ID, 3151 quirk_broken_intx_masking); 3152 3153 static void quirk_no_bus_reset(struct pci_dev *dev) 3154 { 3155 dev->dev_flags |= PCI_DEV_FLAGS_NO_BUS_RESET; 3156 } 3157 3158 /* 3159 * Atheros AR93xx chips do not behave after a bus reset. The device will 3160 * throw a Link Down error on AER-capable systems and regardless of AER, 3161 * config space of the device is never accessible again and typically 3162 * causes the system to hang or reset when access is attempted. 3163 * http://www.spinics.net/lists/linux-pci/msg34797.html 3164 */ 3165 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x0030, quirk_no_bus_reset); 3166 3167 static void quirk_no_pm_reset(struct pci_dev *dev) 3168 { 3169 /* 3170 * We can't do a bus reset on root bus devices, but an ineffective 3171 * PM reset may be better than nothing. 3172 */ 3173 if (!pci_is_root_bus(dev->bus)) 3174 dev->dev_flags |= PCI_DEV_FLAGS_NO_PM_RESET; 3175 } 3176 3177 /* 3178 * Some AMD/ATI GPUS (HD8570 - Oland) report that a D3hot->D0 transition 3179 * causes a reset (i.e., they advertise NoSoftRst-). This transition seems 3180 * to have no effect on the device: it retains the framebuffer contents and 3181 * monitor sync. Advertising this support makes other layers, like VFIO, 3182 * assume pci_reset_function() is viable for this device. Mark it as 3183 * unavailable to skip it when testing reset methods. 3184 */ 3185 DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_ATI, PCI_ANY_ID, 3186 PCI_CLASS_DISPLAY_VGA, 8, quirk_no_pm_reset); 3187 3188 #ifdef CONFIG_ACPI 3189 /* 3190 * Apple: Shutdown Cactus Ridge Thunderbolt controller. 3191 * 3192 * On Apple hardware the Cactus Ridge Thunderbolt controller needs to be 3193 * shutdown before suspend. Otherwise the native host interface (NHI) will not 3194 * be present after resume if a device was plugged in before suspend. 3195 * 3196 * The thunderbolt controller consists of a pcie switch with downstream 3197 * bridges leading to the NHI and to the tunnel pci bridges. 3198 * 3199 * This quirk cuts power to the whole chip. Therefore we have to apply it 3200 * during suspend_noirq of the upstream bridge. 3201 * 3202 * Power is automagically restored before resume. No action is needed. 3203 */ 3204 static void quirk_apple_poweroff_thunderbolt(struct pci_dev *dev) 3205 { 3206 acpi_handle bridge, SXIO, SXFP, SXLV; 3207 3208 if (!dmi_match(DMI_BOARD_VENDOR, "Apple Inc.")) 3209 return; 3210 if (pci_pcie_type(dev) != PCI_EXP_TYPE_UPSTREAM) 3211 return; 3212 bridge = ACPI_HANDLE(&dev->dev); 3213 if (!bridge) 3214 return; 3215 /* 3216 * SXIO and SXLV are present only on machines requiring this quirk. 3217 * TB bridges in external devices might have the same device id as those 3218 * on the host, but they will not have the associated ACPI methods. This 3219 * implicitly checks that we are at the right bridge. 3220 */ 3221 if (ACPI_FAILURE(acpi_get_handle(bridge, "DSB0.NHI0.SXIO", &SXIO)) 3222 || ACPI_FAILURE(acpi_get_handle(bridge, "DSB0.NHI0.SXFP", &SXFP)) 3223 || ACPI_FAILURE(acpi_get_handle(bridge, "DSB0.NHI0.SXLV", &SXLV))) 3224 return; 3225 dev_info(&dev->dev, "quirk: cutting power to thunderbolt controller...\n"); 3226 3227 /* magic sequence */ 3228 acpi_execute_simple_method(SXIO, NULL, 1); 3229 acpi_execute_simple_method(SXFP, NULL, 0); 3230 msleep(300); 3231 acpi_execute_simple_method(SXLV, NULL, 0); 3232 acpi_execute_simple_method(SXIO, NULL, 0); 3233 acpi_execute_simple_method(SXLV, NULL, 0); 3234 } 3235 DECLARE_PCI_FIXUP_SUSPEND_LATE(PCI_VENDOR_ID_INTEL, 0x1547, 3236 quirk_apple_poweroff_thunderbolt); 3237 3238 /* 3239 * Apple: Wait for the thunderbolt controller to reestablish pci tunnels. 3240 * 3241 * During suspend the thunderbolt controller is reset and all pci 3242 * tunnels are lost. The NHI driver will try to reestablish all tunnels 3243 * during resume. We have to manually wait for the NHI since there is 3244 * no parent child relationship between the NHI and the tunneled 3245 * bridges. 3246 */ 3247 static void quirk_apple_wait_for_thunderbolt(struct pci_dev *dev) 3248 { 3249 struct pci_dev *sibling = NULL; 3250 struct pci_dev *nhi = NULL; 3251 3252 if (!dmi_match(DMI_BOARD_VENDOR, "Apple Inc.")) 3253 return; 3254 if (pci_pcie_type(dev) != PCI_EXP_TYPE_DOWNSTREAM) 3255 return; 3256 /* 3257 * Find the NHI and confirm that we are a bridge on the tb host 3258 * controller and not on a tb endpoint. 3259 */ 3260 sibling = pci_get_slot(dev->bus, 0x0); 3261 if (sibling == dev) 3262 goto out; /* we are the downstream bridge to the NHI */ 3263 if (!sibling || !sibling->subordinate) 3264 goto out; 3265 nhi = pci_get_slot(sibling->subordinate, 0x0); 3266 if (!nhi) 3267 goto out; 3268 if (nhi->vendor != PCI_VENDOR_ID_INTEL 3269 || (nhi->device != 0x1547 && nhi->device != 0x156c) 3270 || nhi->subsystem_vendor != 0x2222 3271 || nhi->subsystem_device != 0x1111) 3272 goto out; 3273 dev_info(&dev->dev, "quirk: waiting for thunderbolt to reestablish PCI tunnels...\n"); 3274 device_pm_wait_for_dev(&dev->dev, &nhi->dev); 3275 out: 3276 pci_dev_put(nhi); 3277 pci_dev_put(sibling); 3278 } 3279 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, 0x1547, 3280 quirk_apple_wait_for_thunderbolt); 3281 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, 0x156d, 3282 quirk_apple_wait_for_thunderbolt); 3283 #endif 3284 3285 static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, 3286 struct pci_fixup *end) 3287 { 3288 ktime_t calltime; 3289 3290 for (; f < end; f++) 3291 if ((f->class == (u32) (dev->class >> f->class_shift) || 3292 f->class == (u32) PCI_ANY_ID) && 3293 (f->vendor == dev->vendor || 3294 f->vendor == (u16) PCI_ANY_ID) && 3295 (f->device == dev->device || 3296 f->device == (u16) PCI_ANY_ID)) { 3297 calltime = fixup_debug_start(dev, f->hook); 3298 f->hook(dev); 3299 fixup_debug_report(dev, calltime, f->hook); 3300 } 3301 } 3302 3303 extern struct pci_fixup __start_pci_fixups_early[]; 3304 extern struct pci_fixup __end_pci_fixups_early[]; 3305 extern struct pci_fixup __start_pci_fixups_header[]; 3306 extern struct pci_fixup __end_pci_fixups_header[]; 3307 extern struct pci_fixup __start_pci_fixups_final[]; 3308 extern struct pci_fixup __end_pci_fixups_final[]; 3309 extern struct pci_fixup __start_pci_fixups_enable[]; 3310 extern struct pci_fixup __end_pci_fixups_enable[]; 3311 extern struct pci_fixup __start_pci_fixups_resume[]; 3312 extern struct pci_fixup __end_pci_fixups_resume[]; 3313 extern struct pci_fixup __start_pci_fixups_resume_early[]; 3314 extern struct pci_fixup __end_pci_fixups_resume_early[]; 3315 extern struct pci_fixup __start_pci_fixups_suspend[]; 3316 extern struct pci_fixup __end_pci_fixups_suspend[]; 3317 extern struct pci_fixup __start_pci_fixups_suspend_late[]; 3318 extern struct pci_fixup __end_pci_fixups_suspend_late[]; 3319 3320 static bool pci_apply_fixup_final_quirks; 3321 3322 void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev) 3323 { 3324 struct pci_fixup *start, *end; 3325 3326 switch (pass) { 3327 case pci_fixup_early: 3328 start = __start_pci_fixups_early; 3329 end = __end_pci_fixups_early; 3330 break; 3331 3332 case pci_fixup_header: 3333 start = __start_pci_fixups_header; 3334 end = __end_pci_fixups_header; 3335 break; 3336 3337 case pci_fixup_final: 3338 if (!pci_apply_fixup_final_quirks) 3339 return; 3340 start = __start_pci_fixups_final; 3341 end = __end_pci_fixups_final; 3342 break; 3343 3344 case pci_fixup_enable: 3345 start = __start_pci_fixups_enable; 3346 end = __end_pci_fixups_enable; 3347 break; 3348 3349 case pci_fixup_resume: 3350 start = __start_pci_fixups_resume; 3351 end = __end_pci_fixups_resume; 3352 break; 3353 3354 case pci_fixup_resume_early: 3355 start = __start_pci_fixups_resume_early; 3356 end = __end_pci_fixups_resume_early; 3357 break; 3358 3359 case pci_fixup_suspend: 3360 start = __start_pci_fixups_suspend; 3361 end = __end_pci_fixups_suspend; 3362 break; 3363 3364 case pci_fixup_suspend_late: 3365 start = __start_pci_fixups_suspend_late; 3366 end = __end_pci_fixups_suspend_late; 3367 break; 3368 3369 default: 3370 /* stupid compiler warning, you would think with an enum... */ 3371 return; 3372 } 3373 pci_do_fixups(dev, start, end); 3374 } 3375 EXPORT_SYMBOL(pci_fixup_device); 3376 3377 3378 static int __init pci_apply_final_quirks(void) 3379 { 3380 struct pci_dev *dev = NULL; 3381 u8 cls = 0; 3382 u8 tmp; 3383 3384 if (pci_cache_line_size) 3385 printk(KERN_DEBUG "PCI: CLS %u bytes\n", 3386 pci_cache_line_size << 2); 3387 3388 pci_apply_fixup_final_quirks = true; 3389 for_each_pci_dev(dev) { 3390 pci_fixup_device(pci_fixup_final, dev); 3391 /* 3392 * If arch hasn't set it explicitly yet, use the CLS 3393 * value shared by all PCI devices. If there's a 3394 * mismatch, fall back to the default value. 3395 */ 3396 if (!pci_cache_line_size) { 3397 pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, &tmp); 3398 if (!cls) 3399 cls = tmp; 3400 if (!tmp || cls == tmp) 3401 continue; 3402 3403 printk(KERN_DEBUG "PCI: CLS mismatch (%u != %u), using %u bytes\n", 3404 cls << 2, tmp << 2, 3405 pci_dfl_cache_line_size << 2); 3406 pci_cache_line_size = pci_dfl_cache_line_size; 3407 } 3408 } 3409 3410 if (!pci_cache_line_size) { 3411 printk(KERN_DEBUG "PCI: CLS %u bytes, default %u\n", 3412 cls << 2, pci_dfl_cache_line_size << 2); 3413 pci_cache_line_size = cls ? cls : pci_dfl_cache_line_size; 3414 } 3415 3416 return 0; 3417 } 3418 3419 fs_initcall_sync(pci_apply_final_quirks); 3420 3421 /* 3422 * Followings are device-specific reset methods which can be used to 3423 * reset a single function if other methods (e.g. FLR, PM D0->D3) are 3424 * not available. 3425 */ 3426 static int reset_intel_82599_sfp_virtfn(struct pci_dev *dev, int probe) 3427 { 3428 /* 3429 * http://www.intel.com/content/dam/doc/datasheet/82599-10-gbe-controller-datasheet.pdf 3430 * 3431 * The 82599 supports FLR on VFs, but FLR support is reported only 3432 * in the PF DEVCAP (sec 9.3.10.4), not in the VF DEVCAP (sec 9.5). 3433 * Therefore, we can't use pcie_flr(), which checks the VF DEVCAP. 3434 */ 3435 3436 if (probe) 3437 return 0; 3438 3439 if (!pci_wait_for_pending_transaction(dev)) 3440 dev_err(&dev->dev, "transaction is not cleared; proceeding with reset anyway\n"); 3441 3442 pcie_capability_set_word(dev, PCI_EXP_DEVCTL, PCI_EXP_DEVCTL_BCR_FLR); 3443 3444 msleep(100); 3445 3446 return 0; 3447 } 3448 3449 #define SOUTH_CHICKEN2 0xc2004 3450 #define PCH_PP_STATUS 0xc7200 3451 #define PCH_PP_CONTROL 0xc7204 3452 #define MSG_CTL 0x45010 3453 #define NSDE_PWR_STATE 0xd0100 3454 #define IGD_OPERATION_TIMEOUT 10000 /* set timeout 10 seconds */ 3455 3456 static int reset_ivb_igd(struct pci_dev *dev, int probe) 3457 { 3458 void __iomem *mmio_base; 3459 unsigned long timeout; 3460 u32 val; 3461 3462 if (probe) 3463 return 0; 3464 3465 mmio_base = pci_iomap(dev, 0, 0); 3466 if (!mmio_base) 3467 return -ENOMEM; 3468 3469 iowrite32(0x00000002, mmio_base + MSG_CTL); 3470 3471 /* 3472 * Clobbering SOUTH_CHICKEN2 register is fine only if the next 3473 * driver loaded sets the right bits. However, this's a reset and 3474 * the bits have been set by i915 previously, so we clobber 3475 * SOUTH_CHICKEN2 register directly here. 3476 */ 3477 iowrite32(0x00000005, mmio_base + SOUTH_CHICKEN2); 3478 3479 val = ioread32(mmio_base + PCH_PP_CONTROL) & 0xfffffffe; 3480 iowrite32(val, mmio_base + PCH_PP_CONTROL); 3481 3482 timeout = jiffies + msecs_to_jiffies(IGD_OPERATION_TIMEOUT); 3483 do { 3484 val = ioread32(mmio_base + PCH_PP_STATUS); 3485 if ((val & 0xb0000000) == 0) 3486 goto reset_complete; 3487 msleep(10); 3488 } while (time_before(jiffies, timeout)); 3489 dev_warn(&dev->dev, "timeout during reset\n"); 3490 3491 reset_complete: 3492 iowrite32(0x00000002, mmio_base + NSDE_PWR_STATE); 3493 3494 pci_iounmap(dev, mmio_base); 3495 return 0; 3496 } 3497 3498 /* 3499 * Device-specific reset method for Chelsio T4-based adapters. 3500 */ 3501 static int reset_chelsio_generic_dev(struct pci_dev *dev, int probe) 3502 { 3503 u16 old_command; 3504 u16 msix_flags; 3505 3506 /* 3507 * If this isn't a Chelsio T4-based device, return -ENOTTY indicating 3508 * that we have no device-specific reset method. 3509 */ 3510 if ((dev->device & 0xf000) != 0x4000) 3511 return -ENOTTY; 3512 3513 /* 3514 * If this is the "probe" phase, return 0 indicating that we can 3515 * reset this device. 3516 */ 3517 if (probe) 3518 return 0; 3519 3520 /* 3521 * T4 can wedge if there are DMAs in flight within the chip and Bus 3522 * Master has been disabled. We need to have it on till the Function 3523 * Level Reset completes. (BUS_MASTER is disabled in 3524 * pci_reset_function()). 3525 */ 3526 pci_read_config_word(dev, PCI_COMMAND, &old_command); 3527 pci_write_config_word(dev, PCI_COMMAND, 3528 old_command | PCI_COMMAND_MASTER); 3529 3530 /* 3531 * Perform the actual device function reset, saving and restoring 3532 * configuration information around the reset. 3533 */ 3534 pci_save_state(dev); 3535 3536 /* 3537 * T4 also suffers a Head-Of-Line blocking problem if MSI-X interrupts 3538 * are disabled when an MSI-X interrupt message needs to be delivered. 3539 * So we briefly re-enable MSI-X interrupts for the duration of the 3540 * FLR. The pci_restore_state() below will restore the original 3541 * MSI-X state. 3542 */ 3543 pci_read_config_word(dev, dev->msix_cap+PCI_MSIX_FLAGS, &msix_flags); 3544 if ((msix_flags & PCI_MSIX_FLAGS_ENABLE) == 0) 3545 pci_write_config_word(dev, dev->msix_cap+PCI_MSIX_FLAGS, 3546 msix_flags | 3547 PCI_MSIX_FLAGS_ENABLE | 3548 PCI_MSIX_FLAGS_MASKALL); 3549 3550 /* 3551 * Start of pcie_flr() code sequence. This reset code is a copy of 3552 * the guts of pcie_flr() because that's not an exported function. 3553 */ 3554 3555 if (!pci_wait_for_pending_transaction(dev)) 3556 dev_err(&dev->dev, "transaction is not cleared; proceeding with reset anyway\n"); 3557 3558 pcie_capability_set_word(dev, PCI_EXP_DEVCTL, PCI_EXP_DEVCTL_BCR_FLR); 3559 msleep(100); 3560 3561 /* 3562 * End of pcie_flr() code sequence. 3563 */ 3564 3565 /* 3566 * Restore the configuration information (BAR values, etc.) including 3567 * the original PCI Configuration Space Command word, and return 3568 * success. 3569 */ 3570 pci_restore_state(dev); 3571 pci_write_config_word(dev, PCI_COMMAND, old_command); 3572 return 0; 3573 } 3574 3575 #define PCI_DEVICE_ID_INTEL_82599_SFP_VF 0x10ed 3576 #define PCI_DEVICE_ID_INTEL_IVB_M_VGA 0x0156 3577 #define PCI_DEVICE_ID_INTEL_IVB_M2_VGA 0x0166 3578 3579 static const struct pci_dev_reset_methods pci_dev_reset_methods[] = { 3580 { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82599_SFP_VF, 3581 reset_intel_82599_sfp_virtfn }, 3582 { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IVB_M_VGA, 3583 reset_ivb_igd }, 3584 { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IVB_M2_VGA, 3585 reset_ivb_igd }, 3586 { PCI_VENDOR_ID_CHELSIO, PCI_ANY_ID, 3587 reset_chelsio_generic_dev }, 3588 { 0 } 3589 }; 3590 3591 /* 3592 * These device-specific reset methods are here rather than in a driver 3593 * because when a host assigns a device to a guest VM, the host may need 3594 * to reset the device but probably doesn't have a driver for it. 3595 */ 3596 int pci_dev_specific_reset(struct pci_dev *dev, int probe) 3597 { 3598 const struct pci_dev_reset_methods *i; 3599 3600 for (i = pci_dev_reset_methods; i->reset; i++) { 3601 if ((i->vendor == dev->vendor || 3602 i->vendor == (u16)PCI_ANY_ID) && 3603 (i->device == dev->device || 3604 i->device == (u16)PCI_ANY_ID)) 3605 return i->reset(dev, probe); 3606 } 3607 3608 return -ENOTTY; 3609 } 3610 3611 static void quirk_dma_func0_alias(struct pci_dev *dev) 3612 { 3613 if (PCI_FUNC(dev->devfn) != 0) { 3614 dev->dma_alias_devfn = PCI_DEVFN(PCI_SLOT(dev->devfn), 0); 3615 dev->dev_flags |= PCI_DEV_FLAGS_DMA_ALIAS_DEVFN; 3616 } 3617 } 3618 3619 /* 3620 * https://bugzilla.redhat.com/show_bug.cgi?id=605888 3621 * 3622 * Some Ricoh devices use function 0 as the PCIe requester ID for DMA. 3623 */ 3624 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_RICOH, 0xe832, quirk_dma_func0_alias); 3625 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_RICOH, 0xe476, quirk_dma_func0_alias); 3626 3627 static void quirk_dma_func1_alias(struct pci_dev *dev) 3628 { 3629 if (PCI_FUNC(dev->devfn) != 1) { 3630 dev->dma_alias_devfn = PCI_DEVFN(PCI_SLOT(dev->devfn), 1); 3631 dev->dev_flags |= PCI_DEV_FLAGS_DMA_ALIAS_DEVFN; 3632 } 3633 } 3634 3635 /* 3636 * Marvell 88SE9123 uses function 1 as the requester ID for DMA. In some 3637 * SKUs function 1 is present and is a legacy IDE controller, in other 3638 * SKUs this function is not present, making this a ghost requester. 3639 * https://bugzilla.kernel.org/show_bug.cgi?id=42679 3640 */ 3641 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9120, 3642 quirk_dma_func1_alias); 3643 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9123, 3644 quirk_dma_func1_alias); 3645 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c14 */ 3646 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9130, 3647 quirk_dma_func1_alias); 3648 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c47 + c57 */ 3649 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9172, 3650 quirk_dma_func1_alias); 3651 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c59 */ 3652 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x917a, 3653 quirk_dma_func1_alias); 3654 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c46 */ 3655 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x91a0, 3656 quirk_dma_func1_alias); 3657 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c49 */ 3658 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9230, 3659 quirk_dma_func1_alias); 3660 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TTI, 0x0642, 3661 quirk_dma_func1_alias); 3662 /* https://bugs.gentoo.org/show_bug.cgi?id=497630 */ 3663 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_JMICRON, 3664 PCI_DEVICE_ID_JMICRON_JMB388_ESD, 3665 quirk_dma_func1_alias); 3666 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c117 */ 3667 DECLARE_PCI_FIXUP_HEADER(0x1c28, /* Lite-On */ 3668 0x0122, /* Plextor M6E (Marvell 88SS9183)*/ 3669 quirk_dma_func1_alias); 3670 3671 /* 3672 * Some devices DMA with the wrong devfn, not just the wrong function. 3673 * quirk_fixed_dma_alias() uses this table to create fixed aliases, where 3674 * the alias is "fixed" and independent of the device devfn. 3675 * 3676 * For example, the Adaptec 3405 is a PCIe card with an Intel 80333 I/O 3677 * processor. To software, this appears as a PCIe-to-PCI/X bridge with a 3678 * single device on the secondary bus. In reality, the single exposed 3679 * device at 0e.0 is the Address Translation Unit (ATU) of the controller 3680 * that provides a bridge to the internal bus of the I/O processor. The 3681 * controller supports private devices, which can be hidden from PCI config 3682 * space. In the case of the Adaptec 3405, a private device at 01.0 3683 * appears to be the DMA engine, which therefore needs to become a DMA 3684 * alias for the device. 3685 */ 3686 static const struct pci_device_id fixed_dma_alias_tbl[] = { 3687 { PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x0285, 3688 PCI_VENDOR_ID_ADAPTEC2, 0x02bb), /* Adaptec 3405 */ 3689 .driver_data = PCI_DEVFN(1, 0) }, 3690 { 0 } 3691 }; 3692 3693 static void quirk_fixed_dma_alias(struct pci_dev *dev) 3694 { 3695 const struct pci_device_id *id; 3696 3697 id = pci_match_id(fixed_dma_alias_tbl, dev); 3698 if (id) { 3699 dev->dma_alias_devfn = id->driver_data; 3700 dev->dev_flags |= PCI_DEV_FLAGS_DMA_ALIAS_DEVFN; 3701 dev_info(&dev->dev, "Enabling fixed DMA alias to %02x.%d\n", 3702 PCI_SLOT(dev->dma_alias_devfn), 3703 PCI_FUNC(dev->dma_alias_devfn)); 3704 } 3705 } 3706 3707 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ADAPTEC2, 0x0285, quirk_fixed_dma_alias); 3708 3709 /* 3710 * A few PCIe-to-PCI bridges fail to expose a PCIe capability, resulting in 3711 * using the wrong DMA alias for the device. Some of these devices can be 3712 * used as either forward or reverse bridges, so we need to test whether the 3713 * device is operating in the correct mode. We could probably apply this 3714 * quirk to PCI_ANY_ID, but for now we'll just use known offenders. The test 3715 * is for a non-root, non-PCIe bridge where the upstream device is PCIe and 3716 * is not a PCIe-to-PCI bridge, then @pdev is actually a PCIe-to-PCI bridge. 3717 */ 3718 static void quirk_use_pcie_bridge_dma_alias(struct pci_dev *pdev) 3719 { 3720 if (!pci_is_root_bus(pdev->bus) && 3721 pdev->hdr_type == PCI_HEADER_TYPE_BRIDGE && 3722 !pci_is_pcie(pdev) && pci_is_pcie(pdev->bus->self) && 3723 pci_pcie_type(pdev->bus->self) != PCI_EXP_TYPE_PCI_BRIDGE) 3724 pdev->dev_flags |= PCI_DEV_FLAG_PCIE_BRIDGE_ALIAS; 3725 } 3726 /* ASM1083/1085, https://bugzilla.kernel.org/show_bug.cgi?id=44881#c46 */ 3727 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ASMEDIA, 0x1080, 3728 quirk_use_pcie_bridge_dma_alias); 3729 /* Tundra 8113, https://bugzilla.kernel.org/show_bug.cgi?id=44881#c43 */ 3730 DECLARE_PCI_FIXUP_HEADER(0x10e3, 0x8113, quirk_use_pcie_bridge_dma_alias); 3731 /* ITE 8892, https://bugzilla.kernel.org/show_bug.cgi?id=73551 */ 3732 DECLARE_PCI_FIXUP_HEADER(0x1283, 0x8892, quirk_use_pcie_bridge_dma_alias); 3733 /* Intel 82801, https://bugzilla.kernel.org/show_bug.cgi?id=44881#c49 */ 3734 DECLARE_PCI_FIXUP_HEADER(0x8086, 0x244e, quirk_use_pcie_bridge_dma_alias); 3735 3736 /* 3737 * Intersil/Techwell TW686[4589]-based video capture cards have an empty (zero) 3738 * class code. Fix it. 3739 */ 3740 static void quirk_tw686x_class(struct pci_dev *pdev) 3741 { 3742 u32 class = pdev->class; 3743 3744 /* Use "Multimedia controller" class */ 3745 pdev->class = (PCI_CLASS_MULTIMEDIA_OTHER << 8) | 0x01; 3746 dev_info(&pdev->dev, "TW686x PCI class overridden (%#08x -> %#08x)\n", 3747 class, pdev->class); 3748 } 3749 DECLARE_PCI_FIXUP_CLASS_EARLY(0x1797, 0x6864, PCI_CLASS_NOT_DEFINED, 8, 3750 quirk_tw686x_class); 3751 DECLARE_PCI_FIXUP_CLASS_EARLY(0x1797, 0x6865, PCI_CLASS_NOT_DEFINED, 8, 3752 quirk_tw686x_class); 3753 DECLARE_PCI_FIXUP_CLASS_EARLY(0x1797, 0x6868, PCI_CLASS_NOT_DEFINED, 8, 3754 quirk_tw686x_class); 3755 DECLARE_PCI_FIXUP_CLASS_EARLY(0x1797, 0x6869, PCI_CLASS_NOT_DEFINED, 8, 3756 quirk_tw686x_class); 3757 3758 /* 3759 * Per PCIe r3.0, sec 2.2.9, "Completion headers must supply the same 3760 * values for the Attribute as were supplied in the header of the 3761 * corresponding Request, except as explicitly allowed when IDO is used." 3762 * 3763 * If a non-compliant device generates a completion with a different 3764 * attribute than the request, the receiver may accept it (which itself 3765 * seems non-compliant based on sec 2.3.2), or it may handle it as a 3766 * Malformed TLP or an Unexpected Completion, which will probably lead to a 3767 * device access timeout. 3768 * 3769 * If the non-compliant device generates completions with zero attributes 3770 * (instead of copying the attributes from the request), we can work around 3771 * this by disabling the "Relaxed Ordering" and "No Snoop" attributes in 3772 * upstream devices so they always generate requests with zero attributes. 3773 * 3774 * This affects other devices under the same Root Port, but since these 3775 * attributes are performance hints, there should be no functional problem. 3776 * 3777 * Note that Configuration Space accesses are never supposed to have TLP 3778 * Attributes, so we're safe waiting till after any Configuration Space 3779 * accesses to do the Root Port fixup. 3780 */ 3781 static void quirk_disable_root_port_attributes(struct pci_dev *pdev) 3782 { 3783 struct pci_dev *root_port = pci_find_pcie_root_port(pdev); 3784 3785 if (!root_port) { 3786 dev_warn(&pdev->dev, "PCIe Completion erratum may cause device errors\n"); 3787 return; 3788 } 3789 3790 dev_info(&root_port->dev, "Disabling No Snoop/Relaxed Ordering Attributes to avoid PCIe Completion erratum in %s\n", 3791 dev_name(&pdev->dev)); 3792 pcie_capability_clear_and_set_word(root_port, PCI_EXP_DEVCTL, 3793 PCI_EXP_DEVCTL_RELAX_EN | 3794 PCI_EXP_DEVCTL_NOSNOOP_EN, 0); 3795 } 3796 3797 /* 3798 * The Chelsio T5 chip fails to copy TLP Attributes from a Request to the 3799 * Completion it generates. 3800 */ 3801 static void quirk_chelsio_T5_disable_root_port_attributes(struct pci_dev *pdev) 3802 { 3803 /* 3804 * This mask/compare operation selects for Physical Function 4 on a 3805 * T5. We only need to fix up the Root Port once for any of the 3806 * PFs. PF[0..3] have PCI Device IDs of 0x50xx, but PF4 is uniquely 3807 * 0x54xx so we use that one, 3808 */ 3809 if ((pdev->device & 0xff00) == 0x5400) 3810 quirk_disable_root_port_attributes(pdev); 3811 } 3812 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_CHELSIO, PCI_ANY_ID, 3813 quirk_chelsio_T5_disable_root_port_attributes); 3814 3815 /* 3816 * AMD has indicated that the devices below do not support peer-to-peer 3817 * in any system where they are found in the southbridge with an AMD 3818 * IOMMU in the system. Multifunction devices that do not support 3819 * peer-to-peer between functions can claim to support a subset of ACS. 3820 * Such devices effectively enable request redirect (RR) and completion 3821 * redirect (CR) since all transactions are redirected to the upstream 3822 * root complex. 3823 * 3824 * http://permalink.gmane.org/gmane.comp.emulators.kvm.devel/94086 3825 * http://permalink.gmane.org/gmane.comp.emulators.kvm.devel/94102 3826 * http://permalink.gmane.org/gmane.comp.emulators.kvm.devel/99402 3827 * 3828 * 1002:4385 SBx00 SMBus Controller 3829 * 1002:439c SB7x0/SB8x0/SB9x0 IDE Controller 3830 * 1002:4383 SBx00 Azalia (Intel HDA) 3831 * 1002:439d SB7x0/SB8x0/SB9x0 LPC host controller 3832 * 1002:4384 SBx00 PCI to PCI Bridge 3833 * 1002:4399 SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 3834 * 3835 * https://bugzilla.kernel.org/show_bug.cgi?id=81841#c15 3836 * 3837 * 1022:780f [AMD] FCH PCI Bridge 3838 * 1022:7809 [AMD] FCH USB OHCI Controller 3839 */ 3840 static int pci_quirk_amd_sb_acs(struct pci_dev *dev, u16 acs_flags) 3841 { 3842 #ifdef CONFIG_ACPI 3843 struct acpi_table_header *header = NULL; 3844 acpi_status status; 3845 3846 /* Targeting multifunction devices on the SB (appears on root bus) */ 3847 if (!dev->multifunction || !pci_is_root_bus(dev->bus)) 3848 return -ENODEV; 3849 3850 /* The IVRS table describes the AMD IOMMU */ 3851 status = acpi_get_table("IVRS", 0, &header); 3852 if (ACPI_FAILURE(status)) 3853 return -ENODEV; 3854 3855 /* Filter out flags not applicable to multifunction */ 3856 acs_flags &= (PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_EC | PCI_ACS_DT); 3857 3858 return acs_flags & ~(PCI_ACS_RR | PCI_ACS_CR) ? 0 : 1; 3859 #else 3860 return -ENODEV; 3861 #endif 3862 } 3863 3864 static int pci_quirk_cavium_acs(struct pci_dev *dev, u16 acs_flags) 3865 { 3866 /* 3867 * Cavium devices matching this quirk do not perform peer-to-peer 3868 * with other functions, allowing masking out these bits as if they 3869 * were unimplemented in the ACS capability. 3870 */ 3871 acs_flags &= ~(PCI_ACS_SV | PCI_ACS_TB | PCI_ACS_RR | 3872 PCI_ACS_CR | PCI_ACS_UF | PCI_ACS_DT); 3873 3874 return acs_flags ? 0 : 1; 3875 } 3876 3877 /* 3878 * Many Intel PCH root ports do provide ACS-like features to disable peer 3879 * transactions and validate bus numbers in requests, but do not provide an 3880 * actual PCIe ACS capability. This is the list of device IDs known to fall 3881 * into that category as provided by Intel in Red Hat bugzilla 1037684. 3882 */ 3883 static const u16 pci_quirk_intel_pch_acs_ids[] = { 3884 /* Ibexpeak PCH */ 3885 0x3b42, 0x3b43, 0x3b44, 0x3b45, 0x3b46, 0x3b47, 0x3b48, 0x3b49, 3886 0x3b4a, 0x3b4b, 0x3b4c, 0x3b4d, 0x3b4e, 0x3b4f, 0x3b50, 0x3b51, 3887 /* Cougarpoint PCH */ 3888 0x1c10, 0x1c11, 0x1c12, 0x1c13, 0x1c14, 0x1c15, 0x1c16, 0x1c17, 3889 0x1c18, 0x1c19, 0x1c1a, 0x1c1b, 0x1c1c, 0x1c1d, 0x1c1e, 0x1c1f, 3890 /* Pantherpoint PCH */ 3891 0x1e10, 0x1e11, 0x1e12, 0x1e13, 0x1e14, 0x1e15, 0x1e16, 0x1e17, 3892 0x1e18, 0x1e19, 0x1e1a, 0x1e1b, 0x1e1c, 0x1e1d, 0x1e1e, 0x1e1f, 3893 /* Lynxpoint-H PCH */ 3894 0x8c10, 0x8c11, 0x8c12, 0x8c13, 0x8c14, 0x8c15, 0x8c16, 0x8c17, 3895 0x8c18, 0x8c19, 0x8c1a, 0x8c1b, 0x8c1c, 0x8c1d, 0x8c1e, 0x8c1f, 3896 /* Lynxpoint-LP PCH */ 3897 0x9c10, 0x9c11, 0x9c12, 0x9c13, 0x9c14, 0x9c15, 0x9c16, 0x9c17, 3898 0x9c18, 0x9c19, 0x9c1a, 0x9c1b, 3899 /* Wildcat PCH */ 3900 0x9c90, 0x9c91, 0x9c92, 0x9c93, 0x9c94, 0x9c95, 0x9c96, 0x9c97, 3901 0x9c98, 0x9c99, 0x9c9a, 0x9c9b, 3902 /* Patsburg (X79) PCH */ 3903 0x1d10, 0x1d12, 0x1d14, 0x1d16, 0x1d18, 0x1d1a, 0x1d1c, 0x1d1e, 3904 /* Wellsburg (X99) PCH */ 3905 0x8d10, 0x8d11, 0x8d12, 0x8d13, 0x8d14, 0x8d15, 0x8d16, 0x8d17, 3906 0x8d18, 0x8d19, 0x8d1a, 0x8d1b, 0x8d1c, 0x8d1d, 0x8d1e, 3907 /* Lynx Point (9 series) PCH */ 3908 0x8c90, 0x8c92, 0x8c94, 0x8c96, 0x8c98, 0x8c9a, 0x8c9c, 0x8c9e, 3909 }; 3910 3911 static bool pci_quirk_intel_pch_acs_match(struct pci_dev *dev) 3912 { 3913 int i; 3914 3915 /* Filter out a few obvious non-matches first */ 3916 if (!pci_is_pcie(dev) || pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT) 3917 return false; 3918 3919 for (i = 0; i < ARRAY_SIZE(pci_quirk_intel_pch_acs_ids); i++) 3920 if (pci_quirk_intel_pch_acs_ids[i] == dev->device) 3921 return true; 3922 3923 return false; 3924 } 3925 3926 #define INTEL_PCH_ACS_FLAGS (PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF | PCI_ACS_SV) 3927 3928 static int pci_quirk_intel_pch_acs(struct pci_dev *dev, u16 acs_flags) 3929 { 3930 u16 flags = dev->dev_flags & PCI_DEV_FLAGS_ACS_ENABLED_QUIRK ? 3931 INTEL_PCH_ACS_FLAGS : 0; 3932 3933 if (!pci_quirk_intel_pch_acs_match(dev)) 3934 return -ENOTTY; 3935 3936 return acs_flags & ~flags ? 0 : 1; 3937 } 3938 3939 static int pci_quirk_mf_endpoint_acs(struct pci_dev *dev, u16 acs_flags) 3940 { 3941 /* 3942 * SV, TB, and UF are not relevant to multifunction endpoints. 3943 * 3944 * Multifunction devices are only required to implement RR, CR, and DT 3945 * in their ACS capability if they support peer-to-peer transactions. 3946 * Devices matching this quirk have been verified by the vendor to not 3947 * perform peer-to-peer with other functions, allowing us to mask out 3948 * these bits as if they were unimplemented in the ACS capability. 3949 */ 3950 acs_flags &= ~(PCI_ACS_SV | PCI_ACS_TB | PCI_ACS_RR | 3951 PCI_ACS_CR | PCI_ACS_UF | PCI_ACS_DT); 3952 3953 return acs_flags ? 0 : 1; 3954 } 3955 3956 static const struct pci_dev_acs_enabled { 3957 u16 vendor; 3958 u16 device; 3959 int (*acs_enabled)(struct pci_dev *dev, u16 acs_flags); 3960 } pci_dev_acs_enabled[] = { 3961 { PCI_VENDOR_ID_ATI, 0x4385, pci_quirk_amd_sb_acs }, 3962 { PCI_VENDOR_ID_ATI, 0x439c, pci_quirk_amd_sb_acs }, 3963 { PCI_VENDOR_ID_ATI, 0x4383, pci_quirk_amd_sb_acs }, 3964 { PCI_VENDOR_ID_ATI, 0x439d, pci_quirk_amd_sb_acs }, 3965 { PCI_VENDOR_ID_ATI, 0x4384, pci_quirk_amd_sb_acs }, 3966 { PCI_VENDOR_ID_ATI, 0x4399, pci_quirk_amd_sb_acs }, 3967 { PCI_VENDOR_ID_AMD, 0x780f, pci_quirk_amd_sb_acs }, 3968 { PCI_VENDOR_ID_AMD, 0x7809, pci_quirk_amd_sb_acs }, 3969 { PCI_VENDOR_ID_SOLARFLARE, 0x0903, pci_quirk_mf_endpoint_acs }, 3970 { PCI_VENDOR_ID_SOLARFLARE, 0x0923, pci_quirk_mf_endpoint_acs }, 3971 { PCI_VENDOR_ID_INTEL, 0x10C6, pci_quirk_mf_endpoint_acs }, 3972 { PCI_VENDOR_ID_INTEL, 0x10DB, pci_quirk_mf_endpoint_acs }, 3973 { PCI_VENDOR_ID_INTEL, 0x10DD, pci_quirk_mf_endpoint_acs }, 3974 { PCI_VENDOR_ID_INTEL, 0x10E1, pci_quirk_mf_endpoint_acs }, 3975 { PCI_VENDOR_ID_INTEL, 0x10F1, pci_quirk_mf_endpoint_acs }, 3976 { PCI_VENDOR_ID_INTEL, 0x10F7, pci_quirk_mf_endpoint_acs }, 3977 { PCI_VENDOR_ID_INTEL, 0x10F8, pci_quirk_mf_endpoint_acs }, 3978 { PCI_VENDOR_ID_INTEL, 0x10F9, pci_quirk_mf_endpoint_acs }, 3979 { PCI_VENDOR_ID_INTEL, 0x10FA, pci_quirk_mf_endpoint_acs }, 3980 { PCI_VENDOR_ID_INTEL, 0x10FB, pci_quirk_mf_endpoint_acs }, 3981 { PCI_VENDOR_ID_INTEL, 0x10FC, pci_quirk_mf_endpoint_acs }, 3982 { PCI_VENDOR_ID_INTEL, 0x1507, pci_quirk_mf_endpoint_acs }, 3983 { PCI_VENDOR_ID_INTEL, 0x1514, pci_quirk_mf_endpoint_acs }, 3984 { PCI_VENDOR_ID_INTEL, 0x151C, pci_quirk_mf_endpoint_acs }, 3985 { PCI_VENDOR_ID_INTEL, 0x1529, pci_quirk_mf_endpoint_acs }, 3986 { PCI_VENDOR_ID_INTEL, 0x152A, pci_quirk_mf_endpoint_acs }, 3987 { PCI_VENDOR_ID_INTEL, 0x154D, pci_quirk_mf_endpoint_acs }, 3988 { PCI_VENDOR_ID_INTEL, 0x154F, pci_quirk_mf_endpoint_acs }, 3989 { PCI_VENDOR_ID_INTEL, 0x1551, pci_quirk_mf_endpoint_acs }, 3990 { PCI_VENDOR_ID_INTEL, 0x1558, pci_quirk_mf_endpoint_acs }, 3991 /* 82580 */ 3992 { PCI_VENDOR_ID_INTEL, 0x1509, pci_quirk_mf_endpoint_acs }, 3993 { PCI_VENDOR_ID_INTEL, 0x150E, pci_quirk_mf_endpoint_acs }, 3994 { PCI_VENDOR_ID_INTEL, 0x150F, pci_quirk_mf_endpoint_acs }, 3995 { PCI_VENDOR_ID_INTEL, 0x1510, pci_quirk_mf_endpoint_acs }, 3996 { PCI_VENDOR_ID_INTEL, 0x1511, pci_quirk_mf_endpoint_acs }, 3997 { PCI_VENDOR_ID_INTEL, 0x1516, pci_quirk_mf_endpoint_acs }, 3998 { PCI_VENDOR_ID_INTEL, 0x1527, pci_quirk_mf_endpoint_acs }, 3999 /* 82576 */ 4000 { PCI_VENDOR_ID_INTEL, 0x10C9, pci_quirk_mf_endpoint_acs }, 4001 { PCI_VENDOR_ID_INTEL, 0x10E6, pci_quirk_mf_endpoint_acs }, 4002 { PCI_VENDOR_ID_INTEL, 0x10E7, pci_quirk_mf_endpoint_acs }, 4003 { PCI_VENDOR_ID_INTEL, 0x10E8, pci_quirk_mf_endpoint_acs }, 4004 { PCI_VENDOR_ID_INTEL, 0x150A, pci_quirk_mf_endpoint_acs }, 4005 { PCI_VENDOR_ID_INTEL, 0x150D, pci_quirk_mf_endpoint_acs }, 4006 { PCI_VENDOR_ID_INTEL, 0x1518, pci_quirk_mf_endpoint_acs }, 4007 { PCI_VENDOR_ID_INTEL, 0x1526, pci_quirk_mf_endpoint_acs }, 4008 /* 82575 */ 4009 { PCI_VENDOR_ID_INTEL, 0x10A7, pci_quirk_mf_endpoint_acs }, 4010 { PCI_VENDOR_ID_INTEL, 0x10A9, pci_quirk_mf_endpoint_acs }, 4011 { PCI_VENDOR_ID_INTEL, 0x10D6, pci_quirk_mf_endpoint_acs }, 4012 /* I350 */ 4013 { PCI_VENDOR_ID_INTEL, 0x1521, pci_quirk_mf_endpoint_acs }, 4014 { PCI_VENDOR_ID_INTEL, 0x1522, pci_quirk_mf_endpoint_acs }, 4015 { PCI_VENDOR_ID_INTEL, 0x1523, pci_quirk_mf_endpoint_acs }, 4016 { PCI_VENDOR_ID_INTEL, 0x1524, pci_quirk_mf_endpoint_acs }, 4017 /* 82571 (Quads omitted due to non-ACS switch) */ 4018 { PCI_VENDOR_ID_INTEL, 0x105E, pci_quirk_mf_endpoint_acs }, 4019 { PCI_VENDOR_ID_INTEL, 0x105F, pci_quirk_mf_endpoint_acs }, 4020 { PCI_VENDOR_ID_INTEL, 0x1060, pci_quirk_mf_endpoint_acs }, 4021 { PCI_VENDOR_ID_INTEL, 0x10D9, pci_quirk_mf_endpoint_acs }, 4022 /* I219 */ 4023 { PCI_VENDOR_ID_INTEL, 0x15b7, pci_quirk_mf_endpoint_acs }, 4024 { PCI_VENDOR_ID_INTEL, 0x15b8, pci_quirk_mf_endpoint_acs }, 4025 /* Intel PCH root ports */ 4026 { PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_quirk_intel_pch_acs }, 4027 { 0x19a2, 0x710, pci_quirk_mf_endpoint_acs }, /* Emulex BE3-R */ 4028 { 0x10df, 0x720, pci_quirk_mf_endpoint_acs }, /* Emulex Skyhawk-R */ 4029 /* Cavium ThunderX */ 4030 { PCI_VENDOR_ID_CAVIUM, PCI_ANY_ID, pci_quirk_cavium_acs }, 4031 { 0 } 4032 }; 4033 4034 int pci_dev_specific_acs_enabled(struct pci_dev *dev, u16 acs_flags) 4035 { 4036 const struct pci_dev_acs_enabled *i; 4037 int ret; 4038 4039 /* 4040 * Allow devices that do not expose standard PCIe ACS capabilities 4041 * or control to indicate their support here. Multi-function express 4042 * devices which do not allow internal peer-to-peer between functions, 4043 * but do not implement PCIe ACS may wish to return true here. 4044 */ 4045 for (i = pci_dev_acs_enabled; i->acs_enabled; i++) { 4046 if ((i->vendor == dev->vendor || 4047 i->vendor == (u16)PCI_ANY_ID) && 4048 (i->device == dev->device || 4049 i->device == (u16)PCI_ANY_ID)) { 4050 ret = i->acs_enabled(dev, acs_flags); 4051 if (ret >= 0) 4052 return ret; 4053 } 4054 } 4055 4056 return -ENOTTY; 4057 } 4058 4059 /* Config space offset of Root Complex Base Address register */ 4060 #define INTEL_LPC_RCBA_REG 0xf0 4061 /* 31:14 RCBA address */ 4062 #define INTEL_LPC_RCBA_MASK 0xffffc000 4063 /* RCBA Enable */ 4064 #define INTEL_LPC_RCBA_ENABLE (1 << 0) 4065 4066 /* Backbone Scratch Pad Register */ 4067 #define INTEL_BSPR_REG 0x1104 4068 /* Backbone Peer Non-Posted Disable */ 4069 #define INTEL_BSPR_REG_BPNPD (1 << 8) 4070 /* Backbone Peer Posted Disable */ 4071 #define INTEL_BSPR_REG_BPPD (1 << 9) 4072 4073 /* Upstream Peer Decode Configuration Register */ 4074 #define INTEL_UPDCR_REG 0x1114 4075 /* 5:0 Peer Decode Enable bits */ 4076 #define INTEL_UPDCR_REG_MASK 0x3f 4077 4078 static int pci_quirk_enable_intel_lpc_acs(struct pci_dev *dev) 4079 { 4080 u32 rcba, bspr, updcr; 4081 void __iomem *rcba_mem; 4082 4083 /* 4084 * Read the RCBA register from the LPC (D31:F0). PCH root ports 4085 * are D28:F* and therefore get probed before LPC, thus we can't 4086 * use pci_get_slot/pci_read_config_dword here. 4087 */ 4088 pci_bus_read_config_dword(dev->bus, PCI_DEVFN(31, 0), 4089 INTEL_LPC_RCBA_REG, &rcba); 4090 if (!(rcba & INTEL_LPC_RCBA_ENABLE)) 4091 return -EINVAL; 4092 4093 rcba_mem = ioremap_nocache(rcba & INTEL_LPC_RCBA_MASK, 4094 PAGE_ALIGN(INTEL_UPDCR_REG)); 4095 if (!rcba_mem) 4096 return -ENOMEM; 4097 4098 /* 4099 * The BSPR can disallow peer cycles, but it's set by soft strap and 4100 * therefore read-only. If both posted and non-posted peer cycles are 4101 * disallowed, we're ok. If either are allowed, then we need to use 4102 * the UPDCR to disable peer decodes for each port. This provides the 4103 * PCIe ACS equivalent of PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF 4104 */ 4105 bspr = readl(rcba_mem + INTEL_BSPR_REG); 4106 bspr &= INTEL_BSPR_REG_BPNPD | INTEL_BSPR_REG_BPPD; 4107 if (bspr != (INTEL_BSPR_REG_BPNPD | INTEL_BSPR_REG_BPPD)) { 4108 updcr = readl(rcba_mem + INTEL_UPDCR_REG); 4109 if (updcr & INTEL_UPDCR_REG_MASK) { 4110 dev_info(&dev->dev, "Disabling UPDCR peer decodes\n"); 4111 updcr &= ~INTEL_UPDCR_REG_MASK; 4112 writel(updcr, rcba_mem + INTEL_UPDCR_REG); 4113 } 4114 } 4115 4116 iounmap(rcba_mem); 4117 return 0; 4118 } 4119 4120 /* Miscellaneous Port Configuration register */ 4121 #define INTEL_MPC_REG 0xd8 4122 /* MPC: Invalid Receive Bus Number Check Enable */ 4123 #define INTEL_MPC_REG_IRBNCE (1 << 26) 4124 4125 static void pci_quirk_enable_intel_rp_mpc_acs(struct pci_dev *dev) 4126 { 4127 u32 mpc; 4128 4129 /* 4130 * When enabled, the IRBNCE bit of the MPC register enables the 4131 * equivalent of PCI ACS Source Validation (PCI_ACS_SV), which 4132 * ensures that requester IDs fall within the bus number range 4133 * of the bridge. Enable if not already. 4134 */ 4135 pci_read_config_dword(dev, INTEL_MPC_REG, &mpc); 4136 if (!(mpc & INTEL_MPC_REG_IRBNCE)) { 4137 dev_info(&dev->dev, "Enabling MPC IRBNCE\n"); 4138 mpc |= INTEL_MPC_REG_IRBNCE; 4139 pci_write_config_word(dev, INTEL_MPC_REG, mpc); 4140 } 4141 } 4142 4143 static int pci_quirk_enable_intel_pch_acs(struct pci_dev *dev) 4144 { 4145 if (!pci_quirk_intel_pch_acs_match(dev)) 4146 return -ENOTTY; 4147 4148 if (pci_quirk_enable_intel_lpc_acs(dev)) { 4149 dev_warn(&dev->dev, "Failed to enable Intel PCH ACS quirk\n"); 4150 return 0; 4151 } 4152 4153 pci_quirk_enable_intel_rp_mpc_acs(dev); 4154 4155 dev->dev_flags |= PCI_DEV_FLAGS_ACS_ENABLED_QUIRK; 4156 4157 dev_info(&dev->dev, "Intel PCH root port ACS workaround enabled\n"); 4158 4159 return 0; 4160 } 4161 4162 static const struct pci_dev_enable_acs { 4163 u16 vendor; 4164 u16 device; 4165 int (*enable_acs)(struct pci_dev *dev); 4166 } pci_dev_enable_acs[] = { 4167 { PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_quirk_enable_intel_pch_acs }, 4168 { 0 } 4169 }; 4170 4171 void pci_dev_specific_enable_acs(struct pci_dev *dev) 4172 { 4173 const struct pci_dev_enable_acs *i; 4174 int ret; 4175 4176 for (i = pci_dev_enable_acs; i->enable_acs; i++) { 4177 if ((i->vendor == dev->vendor || 4178 i->vendor == (u16)PCI_ANY_ID) && 4179 (i->device == dev->device || 4180 i->device == (u16)PCI_ANY_ID)) { 4181 ret = i->enable_acs(dev); 4182 if (ret >= 0) 4183 return; 4184 } 4185 } 4186 } 4187 4188 /* 4189 * The PCI capabilities list for Intel DH895xCC VFs (device id 0x0443) with 4190 * QuickAssist Technology (QAT) is prematurely terminated in hardware. The 4191 * Next Capability pointer in the MSI Capability Structure should point to 4192 * the PCIe Capability Structure but is incorrectly hardwired as 0 terminating 4193 * the list. 4194 */ 4195 static void quirk_intel_qat_vf_cap(struct pci_dev *pdev) 4196 { 4197 int pos, i = 0; 4198 u8 next_cap; 4199 u16 reg16, *cap; 4200 struct pci_cap_saved_state *state; 4201 4202 /* Bail if the hardware bug is fixed */ 4203 if (pdev->pcie_cap || pci_find_capability(pdev, PCI_CAP_ID_EXP)) 4204 return; 4205 4206 /* Bail if MSI Capability Structure is not found for some reason */ 4207 pos = pci_find_capability(pdev, PCI_CAP_ID_MSI); 4208 if (!pos) 4209 return; 4210 4211 /* 4212 * Bail if Next Capability pointer in the MSI Capability Structure 4213 * is not the expected incorrect 0x00. 4214 */ 4215 pci_read_config_byte(pdev, pos + 1, &next_cap); 4216 if (next_cap) 4217 return; 4218 4219 /* 4220 * PCIe Capability Structure is expected to be at 0x50 and should 4221 * terminate the list (Next Capability pointer is 0x00). Verify 4222 * Capability Id and Next Capability pointer is as expected. 4223 * Open-code some of set_pcie_port_type() and pci_cfg_space_size_ext() 4224 * to correctly set kernel data structures which have already been 4225 * set incorrectly due to the hardware bug. 4226 */ 4227 pos = 0x50; 4228 pci_read_config_word(pdev, pos, ®16); 4229 if (reg16 == (0x0000 | PCI_CAP_ID_EXP)) { 4230 u32 status; 4231 #ifndef PCI_EXP_SAVE_REGS 4232 #define PCI_EXP_SAVE_REGS 7 4233 #endif 4234 int size = PCI_EXP_SAVE_REGS * sizeof(u16); 4235 4236 pdev->pcie_cap = pos; 4237 pci_read_config_word(pdev, pos + PCI_EXP_FLAGS, ®16); 4238 pdev->pcie_flags_reg = reg16; 4239 pci_read_config_word(pdev, pos + PCI_EXP_DEVCAP, ®16); 4240 pdev->pcie_mpss = reg16 & PCI_EXP_DEVCAP_PAYLOAD; 4241 4242 pdev->cfg_size = PCI_CFG_SPACE_EXP_SIZE; 4243 if (pci_read_config_dword(pdev, PCI_CFG_SPACE_SIZE, &status) != 4244 PCIBIOS_SUCCESSFUL || (status == 0xffffffff)) 4245 pdev->cfg_size = PCI_CFG_SPACE_SIZE; 4246 4247 if (pci_find_saved_cap(pdev, PCI_CAP_ID_EXP)) 4248 return; 4249 4250 /* 4251 * Save PCIE cap 4252 */ 4253 state = kzalloc(sizeof(*state) + size, GFP_KERNEL); 4254 if (!state) 4255 return; 4256 4257 state->cap.cap_nr = PCI_CAP_ID_EXP; 4258 state->cap.cap_extended = 0; 4259 state->cap.size = size; 4260 cap = (u16 *)&state->cap.data[0]; 4261 pcie_capability_read_word(pdev, PCI_EXP_DEVCTL, &cap[i++]); 4262 pcie_capability_read_word(pdev, PCI_EXP_LNKCTL, &cap[i++]); 4263 pcie_capability_read_word(pdev, PCI_EXP_SLTCTL, &cap[i++]); 4264 pcie_capability_read_word(pdev, PCI_EXP_RTCTL, &cap[i++]); 4265 pcie_capability_read_word(pdev, PCI_EXP_DEVCTL2, &cap[i++]); 4266 pcie_capability_read_word(pdev, PCI_EXP_LNKCTL2, &cap[i++]); 4267 pcie_capability_read_word(pdev, PCI_EXP_SLTCTL2, &cap[i++]); 4268 hlist_add_head(&state->next, &pdev->saved_cap_space); 4269 } 4270 } 4271 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x443, quirk_intel_qat_vf_cap); 4272