1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * This file contains work-arounds for many known PCI hardware bugs. 4 * Devices present only on certain architectures (host bridges et cetera) 5 * should be handled in arch-specific code. 6 * 7 * Note: any quirks for hotpluggable devices must _NOT_ be declared __init. 8 * 9 * Copyright (c) 1999 Martin Mares <mj@ucw.cz> 10 * 11 * Init/reset quirks for USB host controllers should be in the USB quirks 12 * file, where their drivers can use them. 13 */ 14 15 #include <linux/bitfield.h> 16 #include <linux/types.h> 17 #include <linux/kernel.h> 18 #include <linux/export.h> 19 #include <linux/pci.h> 20 #include <linux/isa-dma.h> /* isa_dma_bridge_buggy */ 21 #include <linux/init.h> 22 #include <linux/delay.h> 23 #include <linux/acpi.h> 24 #include <linux/dmi.h> 25 #include <linux/ioport.h> 26 #include <linux/sched.h> 27 #include <linux/ktime.h> 28 #include <linux/mm.h> 29 #include <linux/nvme.h> 30 #include <linux/platform_data/x86/apple.h> 31 #include <linux/pm_runtime.h> 32 #include <linux/suspend.h> 33 #include <linux/switchtec.h> 34 #include "pci.h" 35 36 /* 37 * Retrain the link of a downstream PCIe port by hand if necessary. 38 * 39 * This is needed at least where a downstream port of the ASMedia ASM2824 40 * Gen 3 switch is wired to the upstream port of the Pericom PI7C9X2G304 41 * Gen 2 switch, and observed with the Delock Riser Card PCI Express x1 > 42 * 2 x PCIe x1 device, P/N 41433, plugged into the SiFive HiFive Unmatched 43 * board. 44 * 45 * In such a configuration the switches are supposed to negotiate the link 46 * speed of preferably 5.0GT/s, falling back to 2.5GT/s. However the link 47 * continues switching between the two speeds indefinitely and the data 48 * link layer never reaches the active state, with link training reported 49 * repeatedly active ~84% of the time. Forcing the target link speed to 50 * 2.5GT/s with the upstream ASM2824 device makes the two switches talk to 51 * each other correctly however. And more interestingly retraining with a 52 * higher target link speed afterwards lets the two successfully negotiate 53 * 5.0GT/s. 54 * 55 * With the ASM2824 we can rely on the otherwise optional Data Link Layer 56 * Link Active status bit and in the failed link training scenario it will 57 * be off along with the Link Bandwidth Management Status indicating that 58 * hardware has changed the link speed or width in an attempt to correct 59 * unreliable link operation. For a port that has been left unconnected 60 * both bits will be clear. So use this information to detect the problem 61 * rather than polling the Link Training bit and watching out for flips or 62 * at least the active status. 63 * 64 * Since the exact nature of the problem isn't known and in principle this 65 * could trigger where an ASM2824 device is downstream rather upstream, 66 * apply this erratum workaround to any downstream ports as long as they 67 * support Link Active reporting and have the Link Control 2 register. 68 * Restrict the speed to 2.5GT/s then with the Target Link Speed field, 69 * request a retrain and check the result. 70 * 71 * If this turns out successful and we know by the Vendor:Device ID it is 72 * safe to do so, then lift the restriction, letting the devices negotiate 73 * a higher speed. Also check for a similar 2.5GT/s speed restriction the 74 * firmware may have already arranged and lift it with ports that already 75 * report their data link being up. 76 * 77 * Otherwise revert the speed to the original setting and request a retrain 78 * again to remove any residual state, ignoring the result as it's supposed 79 * to fail anyway. 80 * 81 * Return 0 if the link has been successfully retrained. Return an error 82 * if retraining was not needed or we attempted a retrain and it failed. 83 */ 84 int pcie_failed_link_retrain(struct pci_dev *dev) 85 { 86 static const struct pci_device_id ids[] = { 87 { PCI_VDEVICE(ASMEDIA, 0x2824) }, /* ASMedia ASM2824 */ 88 {} 89 }; 90 u16 lnksta, lnkctl2; 91 int ret = -ENOTTY; 92 93 if (!pci_is_pcie(dev) || !pcie_downstream_port(dev) || 94 !pcie_cap_has_lnkctl2(dev) || !dev->link_active_reporting) 95 return ret; 96 97 pcie_capability_read_word(dev, PCI_EXP_LNKCTL2, &lnkctl2); 98 pcie_capability_read_word(dev, PCI_EXP_LNKSTA, &lnksta); 99 if ((lnksta & (PCI_EXP_LNKSTA_LBMS | PCI_EXP_LNKSTA_DLLLA)) == 100 PCI_EXP_LNKSTA_LBMS) { 101 u16 oldlnkctl2 = lnkctl2; 102 103 pci_info(dev, "broken device, retraining non-functional downstream link at 2.5GT/s\n"); 104 105 lnkctl2 &= ~PCI_EXP_LNKCTL2_TLS; 106 lnkctl2 |= PCI_EXP_LNKCTL2_TLS_2_5GT; 107 pcie_capability_write_word(dev, PCI_EXP_LNKCTL2, lnkctl2); 108 109 ret = pcie_retrain_link(dev, false); 110 if (ret) { 111 pci_info(dev, "retraining failed\n"); 112 pcie_capability_write_word(dev, PCI_EXP_LNKCTL2, 113 oldlnkctl2); 114 pcie_retrain_link(dev, true); 115 return ret; 116 } 117 118 pcie_capability_read_word(dev, PCI_EXP_LNKSTA, &lnksta); 119 } 120 121 if ((lnksta & PCI_EXP_LNKSTA_DLLLA) && 122 (lnkctl2 & PCI_EXP_LNKCTL2_TLS) == PCI_EXP_LNKCTL2_TLS_2_5GT && 123 pci_match_id(ids, dev)) { 124 u32 lnkcap; 125 126 pci_info(dev, "removing 2.5GT/s downstream link speed restriction\n"); 127 pcie_capability_read_dword(dev, PCI_EXP_LNKCAP, &lnkcap); 128 lnkctl2 &= ~PCI_EXP_LNKCTL2_TLS; 129 lnkctl2 |= lnkcap & PCI_EXP_LNKCAP_SLS; 130 pcie_capability_write_word(dev, PCI_EXP_LNKCTL2, lnkctl2); 131 132 ret = pcie_retrain_link(dev, false); 133 if (ret) { 134 pci_info(dev, "retraining failed\n"); 135 return ret; 136 } 137 } 138 139 return ret; 140 } 141 142 static ktime_t fixup_debug_start(struct pci_dev *dev, 143 void (*fn)(struct pci_dev *dev)) 144 { 145 if (initcall_debug) 146 pci_info(dev, "calling %pS @ %i\n", fn, task_pid_nr(current)); 147 148 return ktime_get(); 149 } 150 151 static void fixup_debug_report(struct pci_dev *dev, ktime_t calltime, 152 void (*fn)(struct pci_dev *dev)) 153 { 154 ktime_t delta, rettime; 155 unsigned long long duration; 156 157 rettime = ktime_get(); 158 delta = ktime_sub(rettime, calltime); 159 duration = (unsigned long long) ktime_to_ns(delta) >> 10; 160 if (initcall_debug || duration > 10000) 161 pci_info(dev, "%pS took %lld usecs\n", fn, duration); 162 } 163 164 static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, 165 struct pci_fixup *end) 166 { 167 ktime_t calltime; 168 169 for (; f < end; f++) 170 if ((f->class == (u32) (dev->class >> f->class_shift) || 171 f->class == (u32) PCI_ANY_ID) && 172 (f->vendor == dev->vendor || 173 f->vendor == (u16) PCI_ANY_ID) && 174 (f->device == dev->device || 175 f->device == (u16) PCI_ANY_ID)) { 176 void (*hook)(struct pci_dev *dev); 177 #ifdef CONFIG_HAVE_ARCH_PREL32_RELOCATIONS 178 hook = offset_to_ptr(&f->hook_offset); 179 #else 180 hook = f->hook; 181 #endif 182 calltime = fixup_debug_start(dev, hook); 183 hook(dev); 184 fixup_debug_report(dev, calltime, hook); 185 } 186 } 187 188 extern struct pci_fixup __start_pci_fixups_early[]; 189 extern struct pci_fixup __end_pci_fixups_early[]; 190 extern struct pci_fixup __start_pci_fixups_header[]; 191 extern struct pci_fixup __end_pci_fixups_header[]; 192 extern struct pci_fixup __start_pci_fixups_final[]; 193 extern struct pci_fixup __end_pci_fixups_final[]; 194 extern struct pci_fixup __start_pci_fixups_enable[]; 195 extern struct pci_fixup __end_pci_fixups_enable[]; 196 extern struct pci_fixup __start_pci_fixups_resume[]; 197 extern struct pci_fixup __end_pci_fixups_resume[]; 198 extern struct pci_fixup __start_pci_fixups_resume_early[]; 199 extern struct pci_fixup __end_pci_fixups_resume_early[]; 200 extern struct pci_fixup __start_pci_fixups_suspend[]; 201 extern struct pci_fixup __end_pci_fixups_suspend[]; 202 extern struct pci_fixup __start_pci_fixups_suspend_late[]; 203 extern struct pci_fixup __end_pci_fixups_suspend_late[]; 204 205 static bool pci_apply_fixup_final_quirks; 206 207 void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev) 208 { 209 struct pci_fixup *start, *end; 210 211 switch (pass) { 212 case pci_fixup_early: 213 start = __start_pci_fixups_early; 214 end = __end_pci_fixups_early; 215 break; 216 217 case pci_fixup_header: 218 start = __start_pci_fixups_header; 219 end = __end_pci_fixups_header; 220 break; 221 222 case pci_fixup_final: 223 if (!pci_apply_fixup_final_quirks) 224 return; 225 start = __start_pci_fixups_final; 226 end = __end_pci_fixups_final; 227 break; 228 229 case pci_fixup_enable: 230 start = __start_pci_fixups_enable; 231 end = __end_pci_fixups_enable; 232 break; 233 234 case pci_fixup_resume: 235 start = __start_pci_fixups_resume; 236 end = __end_pci_fixups_resume; 237 break; 238 239 case pci_fixup_resume_early: 240 start = __start_pci_fixups_resume_early; 241 end = __end_pci_fixups_resume_early; 242 break; 243 244 case pci_fixup_suspend: 245 start = __start_pci_fixups_suspend; 246 end = __end_pci_fixups_suspend; 247 break; 248 249 case pci_fixup_suspend_late: 250 start = __start_pci_fixups_suspend_late; 251 end = __end_pci_fixups_suspend_late; 252 break; 253 254 default: 255 /* stupid compiler warning, you would think with an enum... */ 256 return; 257 } 258 pci_do_fixups(dev, start, end); 259 } 260 EXPORT_SYMBOL(pci_fixup_device); 261 262 static int __init pci_apply_final_quirks(void) 263 { 264 struct pci_dev *dev = NULL; 265 u8 cls = 0; 266 u8 tmp; 267 268 if (pci_cache_line_size) 269 pr_info("PCI: CLS %u bytes\n", pci_cache_line_size << 2); 270 271 pci_apply_fixup_final_quirks = true; 272 for_each_pci_dev(dev) { 273 pci_fixup_device(pci_fixup_final, dev); 274 /* 275 * If arch hasn't set it explicitly yet, use the CLS 276 * value shared by all PCI devices. If there's a 277 * mismatch, fall back to the default value. 278 */ 279 if (!pci_cache_line_size) { 280 pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, &tmp); 281 if (!cls) 282 cls = tmp; 283 if (!tmp || cls == tmp) 284 continue; 285 286 pci_info(dev, "CLS mismatch (%u != %u), using %u bytes\n", 287 cls << 2, tmp << 2, 288 pci_dfl_cache_line_size << 2); 289 pci_cache_line_size = pci_dfl_cache_line_size; 290 } 291 } 292 293 if (!pci_cache_line_size) { 294 pr_info("PCI: CLS %u bytes, default %u\n", cls << 2, 295 pci_dfl_cache_line_size << 2); 296 pci_cache_line_size = cls ? cls : pci_dfl_cache_line_size; 297 } 298 299 return 0; 300 } 301 fs_initcall_sync(pci_apply_final_quirks); 302 303 /* 304 * Decoding should be disabled for a PCI device during BAR sizing to avoid 305 * conflict. But doing so may cause problems on host bridge and perhaps other 306 * key system devices. For devices that need to have mmio decoding always-on, 307 * we need to set the dev->mmio_always_on bit. 308 */ 309 static void quirk_mmio_always_on(struct pci_dev *dev) 310 { 311 dev->mmio_always_on = 1; 312 } 313 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_ANY_ID, PCI_ANY_ID, 314 PCI_CLASS_BRIDGE_HOST, 8, quirk_mmio_always_on); 315 316 /* 317 * The Mellanox Tavor device gives false positive parity errors. Disable 318 * parity error reporting. 319 */ 320 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_MELLANOX, PCI_DEVICE_ID_MELLANOX_TAVOR, pci_disable_parity); 321 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_MELLANOX, PCI_DEVICE_ID_MELLANOX_TAVOR_BRIDGE, pci_disable_parity); 322 323 /* 324 * Deal with broken BIOSes that neglect to enable passive release, 325 * which can cause problems in combination with the 82441FX/PPro MTRRs 326 */ 327 static void quirk_passive_release(struct pci_dev *dev) 328 { 329 struct pci_dev *d = NULL; 330 unsigned char dlc; 331 332 /* 333 * We have to make sure a particular bit is set in the PIIX3 334 * ISA bridge, so we have to go out and find it. 335 */ 336 while ((d = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, d))) { 337 pci_read_config_byte(d, 0x82, &dlc); 338 if (!(dlc & 1<<1)) { 339 pci_info(d, "PIIX3: Enabling Passive Release\n"); 340 dlc |= 1<<1; 341 pci_write_config_byte(d, 0x82, dlc); 342 } 343 } 344 } 345 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release); 346 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release); 347 348 #ifdef CONFIG_X86_32 349 /* 350 * The VIA VP2/VP3/MVP3 seem to have some 'features'. There may be a 351 * workaround but VIA don't answer queries. If you happen to have good 352 * contacts at VIA ask them for me please -- Alan 353 * 354 * This appears to be BIOS not version dependent. So presumably there is a 355 * chipset level fix. 356 */ 357 static void quirk_isa_dma_hangs(struct pci_dev *dev) 358 { 359 if (!isa_dma_bridge_buggy) { 360 isa_dma_bridge_buggy = 1; 361 pci_info(dev, "Activating ISA DMA hang workarounds\n"); 362 } 363 } 364 /* 365 * It's not totally clear which chipsets are the problematic ones. We know 366 * 82C586 and 82C596 variants are affected. 367 */ 368 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_isa_dma_hangs); 369 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C596, quirk_isa_dma_hangs); 370 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, quirk_isa_dma_hangs); 371 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, quirk_isa_dma_hangs); 372 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_1, quirk_isa_dma_hangs); 373 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_2, quirk_isa_dma_hangs); 374 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_3, quirk_isa_dma_hangs); 375 #endif 376 377 #ifdef CONFIG_HAS_IOPORT 378 /* 379 * Intel NM10 "Tiger Point" LPC PM1a_STS.BM_STS must be clear 380 * for some HT machines to use C4 w/o hanging. 381 */ 382 static void quirk_tigerpoint_bm_sts(struct pci_dev *dev) 383 { 384 u32 pmbase; 385 u16 pm1a; 386 387 pci_read_config_dword(dev, 0x40, &pmbase); 388 pmbase = pmbase & 0xff80; 389 pm1a = inw(pmbase); 390 391 if (pm1a & 0x10) { 392 pci_info(dev, FW_BUG "Tiger Point LPC.BM_STS cleared\n"); 393 outw(0x10, pmbase); 394 } 395 } 396 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_TGP_LPC, quirk_tigerpoint_bm_sts); 397 #endif 398 399 /* Chipsets where PCI->PCI transfers vanish or hang */ 400 static void quirk_nopcipci(struct pci_dev *dev) 401 { 402 if ((pci_pci_problems & PCIPCI_FAIL) == 0) { 403 pci_info(dev, "Disabling direct PCI/PCI transfers\n"); 404 pci_pci_problems |= PCIPCI_FAIL; 405 } 406 } 407 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5597, quirk_nopcipci); 408 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_496, quirk_nopcipci); 409 410 static void quirk_nopciamd(struct pci_dev *dev) 411 { 412 u8 rev; 413 pci_read_config_byte(dev, 0x08, &rev); 414 if (rev == 0x13) { 415 /* Erratum 24 */ 416 pci_info(dev, "Chipset erratum: Disabling direct PCI/AGP transfers\n"); 417 pci_pci_problems |= PCIAGP_FAIL; 418 } 419 } 420 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8151_0, quirk_nopciamd); 421 422 /* Triton requires workarounds to be used by the drivers */ 423 static void quirk_triton(struct pci_dev *dev) 424 { 425 if ((pci_pci_problems&PCIPCI_TRITON) == 0) { 426 pci_info(dev, "Limiting direct PCI/PCI transfers\n"); 427 pci_pci_problems |= PCIPCI_TRITON; 428 } 429 } 430 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437, quirk_triton); 431 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437VX, quirk_triton); 432 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439, quirk_triton); 433 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439TX, quirk_triton); 434 435 /* 436 * VIA Apollo KT133 needs PCI latency patch 437 * Made according to a Windows driver-based patch by George E. Breese; 438 * see PCI Latency Adjust on http://www.viahardware.com/download/viatweak.shtm 439 * Also see http://www.au-ja.org/review-kt133a-1-en.phtml for the info on 440 * which Mr Breese based his work. 441 * 442 * Updated based on further information from the site and also on 443 * information provided by VIA 444 */ 445 static void quirk_vialatency(struct pci_dev *dev) 446 { 447 struct pci_dev *p; 448 u8 busarb; 449 450 /* 451 * Ok, we have a potential problem chipset here. Now see if we have 452 * a buggy southbridge. 453 */ 454 p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, NULL); 455 if (p != NULL) { 456 457 /* 458 * 0x40 - 0x4f == 686B, 0x10 - 0x2f == 686A; 459 * thanks Dan Hollis. 460 * Check for buggy part revisions 461 */ 462 if (p->revision < 0x40 || p->revision > 0x42) 463 goto exit; 464 } else { 465 p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, NULL); 466 if (p == NULL) /* No problem parts */ 467 goto exit; 468 469 /* Check for buggy part revisions */ 470 if (p->revision < 0x10 || p->revision > 0x12) 471 goto exit; 472 } 473 474 /* 475 * Ok we have the problem. Now set the PCI master grant to occur 476 * every master grant. The apparent bug is that under high PCI load 477 * (quite common in Linux of course) you can get data loss when the 478 * CPU is held off the bus for 3 bus master requests. This happens 479 * to include the IDE controllers.... 480 * 481 * VIA only apply this fix when an SB Live! is present but under 482 * both Linux and Windows this isn't enough, and we have seen 483 * corruption without SB Live! but with things like 3 UDMA IDE 484 * controllers. So we ignore that bit of the VIA recommendation.. 485 */ 486 pci_read_config_byte(dev, 0x76, &busarb); 487 488 /* 489 * Set bit 4 and bit 5 of byte 76 to 0x01 490 * "Master priority rotation on every PCI master grant" 491 */ 492 busarb &= ~(1<<5); 493 busarb |= (1<<4); 494 pci_write_config_byte(dev, 0x76, busarb); 495 pci_info(dev, "Applying VIA southbridge workaround\n"); 496 exit: 497 pci_dev_put(p); 498 } 499 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency); 500 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency); 501 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency); 502 /* Must restore this on a resume from RAM */ 503 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency); 504 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency); 505 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency); 506 507 /* VIA Apollo VP3 needs ETBF on BT848/878 */ 508 static void quirk_viaetbf(struct pci_dev *dev) 509 { 510 if ((pci_pci_problems&PCIPCI_VIAETBF) == 0) { 511 pci_info(dev, "Limiting direct PCI/PCI transfers\n"); 512 pci_pci_problems |= PCIPCI_VIAETBF; 513 } 514 } 515 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_viaetbf); 516 517 static void quirk_vsfx(struct pci_dev *dev) 518 { 519 if ((pci_pci_problems&PCIPCI_VSFX) == 0) { 520 pci_info(dev, "Limiting direct PCI/PCI transfers\n"); 521 pci_pci_problems |= PCIPCI_VSFX; 522 } 523 } 524 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C576, quirk_vsfx); 525 526 /* 527 * ALi Magik requires workarounds to be used by the drivers that DMA to AGP 528 * space. Latency must be set to 0xA and Triton workaround applied too. 529 * [Info kindly provided by ALi] 530 */ 531 static void quirk_alimagik(struct pci_dev *dev) 532 { 533 if ((pci_pci_problems&PCIPCI_ALIMAGIK) == 0) { 534 pci_info(dev, "Limiting direct PCI/PCI transfers\n"); 535 pci_pci_problems |= PCIPCI_ALIMAGIK|PCIPCI_TRITON; 536 } 537 } 538 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1647, quirk_alimagik); 539 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1651, quirk_alimagik); 540 541 /* Natoma has some interesting boundary conditions with Zoran stuff at least */ 542 static void quirk_natoma(struct pci_dev *dev) 543 { 544 if ((pci_pci_problems&PCIPCI_NATOMA) == 0) { 545 pci_info(dev, "Limiting direct PCI/PCI transfers\n"); 546 pci_pci_problems |= PCIPCI_NATOMA; 547 } 548 } 549 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_natoma); 550 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_0, quirk_natoma); 551 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_1, quirk_natoma); 552 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_0, quirk_natoma); 553 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_1, quirk_natoma); 554 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_2, quirk_natoma); 555 556 /* 557 * This chip can cause PCI parity errors if config register 0xA0 is read 558 * while DMAs are occurring. 559 */ 560 static void quirk_citrine(struct pci_dev *dev) 561 { 562 dev->cfg_size = 0xA0; 563 } 564 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, PCI_DEVICE_ID_IBM_CITRINE, quirk_citrine); 565 566 /* 567 * This chip can cause bus lockups if config addresses above 0x600 568 * are read or written. 569 */ 570 static void quirk_nfp6000(struct pci_dev *dev) 571 { 572 dev->cfg_size = 0x600; 573 } 574 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETRONOME, PCI_DEVICE_ID_NETRONOME_NFP4000, quirk_nfp6000); 575 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETRONOME, PCI_DEVICE_ID_NETRONOME_NFP6000, quirk_nfp6000); 576 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETRONOME, PCI_DEVICE_ID_NETRONOME_NFP5000, quirk_nfp6000); 577 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETRONOME, PCI_DEVICE_ID_NETRONOME_NFP6000_VF, quirk_nfp6000); 578 579 /* On IBM Crocodile ipr SAS adapters, expand BAR to system page size */ 580 static void quirk_extend_bar_to_page(struct pci_dev *dev) 581 { 582 int i; 583 584 for (i = 0; i < PCI_STD_NUM_BARS; i++) { 585 struct resource *r = &dev->resource[i]; 586 const char *r_name = pci_resource_name(dev, i); 587 588 if (r->flags & IORESOURCE_MEM && resource_size(r) < PAGE_SIZE) { 589 r->end = PAGE_SIZE - 1; 590 r->start = 0; 591 r->flags |= IORESOURCE_UNSET; 592 pci_info(dev, "%s %pR: expanded to page size\n", 593 r_name, r); 594 } 595 } 596 } 597 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, 0x034a, quirk_extend_bar_to_page); 598 599 /* 600 * S3 868 and 968 chips report region size equal to 32M, but they decode 64M. 601 * If it's needed, re-allocate the region. 602 */ 603 static void quirk_s3_64M(struct pci_dev *dev) 604 { 605 struct resource *r = &dev->resource[0]; 606 607 if ((r->start & 0x3ffffff) || r->end != r->start + 0x3ffffff) { 608 r->flags |= IORESOURCE_UNSET; 609 r->start = 0; 610 r->end = 0x3ffffff; 611 } 612 } 613 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_868, quirk_s3_64M); 614 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_968, quirk_s3_64M); 615 616 static void quirk_io(struct pci_dev *dev, int pos, unsigned int size, 617 const char *name) 618 { 619 u32 region; 620 struct pci_bus_region bus_region; 621 struct resource *res = dev->resource + pos; 622 const char *res_name = pci_resource_name(dev, pos); 623 624 pci_read_config_dword(dev, PCI_BASE_ADDRESS_0 + (pos << 2), ®ion); 625 626 if (!region) 627 return; 628 629 res->name = pci_name(dev); 630 res->flags = region & ~PCI_BASE_ADDRESS_IO_MASK; 631 res->flags |= 632 (IORESOURCE_IO | IORESOURCE_PCI_FIXED | IORESOURCE_SIZEALIGN); 633 region &= ~(size - 1); 634 635 /* Convert from PCI bus to resource space */ 636 bus_region.start = region; 637 bus_region.end = region + size - 1; 638 pcibios_bus_to_resource(dev->bus, res, &bus_region); 639 640 pci_info(dev, FW_BUG "%s %pR: %s quirk\n", res_name, res, name); 641 } 642 643 /* 644 * Some CS5536 BIOSes (for example, the Soekris NET5501 board w/ comBIOS 645 * ver. 1.33 20070103) don't set the correct ISA PCI region header info. 646 * BAR0 should be 8 bytes; instead, it may be set to something like 8k 647 * (which conflicts w/ BAR1's memory range). 648 * 649 * CS553x's ISA PCI BARs may also be read-only (ref: 650 * https://bugzilla.kernel.org/show_bug.cgi?id=85991 - Comment #4 forward). 651 */ 652 static void quirk_cs5536_vsa(struct pci_dev *dev) 653 { 654 static char *name = "CS5536 ISA bridge"; 655 656 if (pci_resource_len(dev, 0) != 8) { 657 quirk_io(dev, 0, 8, name); /* SMB */ 658 quirk_io(dev, 1, 256, name); /* GPIO */ 659 quirk_io(dev, 2, 64, name); /* MFGPT */ 660 pci_info(dev, "%s bug detected (incorrect header); workaround applied\n", 661 name); 662 } 663 } 664 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, quirk_cs5536_vsa); 665 666 static void quirk_io_region(struct pci_dev *dev, int port, 667 unsigned int size, int nr, const char *name) 668 { 669 u16 region; 670 struct pci_bus_region bus_region; 671 struct resource *res = dev->resource + nr; 672 673 pci_read_config_word(dev, port, ®ion); 674 region &= ~(size - 1); 675 676 if (!region) 677 return; 678 679 res->name = pci_name(dev); 680 res->flags = IORESOURCE_IO; 681 682 /* Convert from PCI bus to resource space */ 683 bus_region.start = region; 684 bus_region.end = region + size - 1; 685 pcibios_bus_to_resource(dev->bus, res, &bus_region); 686 687 /* 688 * "res" is typically a bridge window resource that's not being 689 * used for a bridge window, so it's just a place to stash this 690 * non-standard resource. Printing "nr" or pci_resource_name() of 691 * it doesn't really make sense. 692 */ 693 if (!pci_claim_resource(dev, nr)) 694 pci_info(dev, "quirk: %pR claimed by %s\n", res, name); 695 } 696 697 /* 698 * ATI Northbridge setups MCE the processor if you even read somewhere 699 * between 0x3b0->0x3bb or read 0x3d3 700 */ 701 static void quirk_ati_exploding_mce(struct pci_dev *dev) 702 { 703 pci_info(dev, "ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb\n"); 704 /* Mae rhaid i ni beidio ag edrych ar y lleoliadiau I/O hyn */ 705 request_region(0x3b0, 0x0C, "RadeonIGP"); 706 request_region(0x3d3, 0x01, "RadeonIGP"); 707 } 708 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS100, quirk_ati_exploding_mce); 709 710 /* 711 * In the AMD NL platform, this device ([1022:7912]) has a class code of 712 * PCI_CLASS_SERIAL_USB_XHCI (0x0c0330), which means the xhci driver will 713 * claim it. The same applies on the VanGogh platform device ([1022:163a]). 714 * 715 * But the dwc3 driver is a more specific driver for this device, and we'd 716 * prefer to use it instead of xhci. To prevent xhci from claiming the 717 * device, change the class code to 0x0c03fe, which the PCI r3.0 spec 718 * defines as "USB device (not host controller)". The dwc3 driver can then 719 * claim it based on its Vendor and Device ID. 720 */ 721 static void quirk_amd_dwc_class(struct pci_dev *pdev) 722 { 723 u32 class = pdev->class; 724 725 if (class != PCI_CLASS_SERIAL_USB_DEVICE) { 726 /* Use "USB Device (not host controller)" class */ 727 pdev->class = PCI_CLASS_SERIAL_USB_DEVICE; 728 pci_info(pdev, 729 "PCI class overridden (%#08x -> %#08x) so dwc3 driver can claim this instead of xhci\n", 730 class, pdev->class); 731 } 732 } 733 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_NL_USB, 734 quirk_amd_dwc_class); 735 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VANGOGH_USB, 736 quirk_amd_dwc_class); 737 738 /* 739 * Synopsys USB 3.x host HAPS platform has a class code of 740 * PCI_CLASS_SERIAL_USB_XHCI, and xhci driver can claim it. However, these 741 * devices should use dwc3-haps driver. Change these devices' class code to 742 * PCI_CLASS_SERIAL_USB_DEVICE to prevent the xhci-pci driver from claiming 743 * them. 744 */ 745 static void quirk_synopsys_haps(struct pci_dev *pdev) 746 { 747 u32 class = pdev->class; 748 749 switch (pdev->device) { 750 case PCI_DEVICE_ID_SYNOPSYS_HAPSUSB3: 751 case PCI_DEVICE_ID_SYNOPSYS_HAPSUSB3_AXI: 752 case PCI_DEVICE_ID_SYNOPSYS_HAPSUSB31: 753 pdev->class = PCI_CLASS_SERIAL_USB_DEVICE; 754 pci_info(pdev, "PCI class overridden (%#08x -> %#08x) so dwc3 driver can claim this instead of xhci\n", 755 class, pdev->class); 756 break; 757 } 758 } 759 DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_SYNOPSYS, PCI_ANY_ID, 760 PCI_CLASS_SERIAL_USB_XHCI, 0, 761 quirk_synopsys_haps); 762 763 /* 764 * Let's make the southbridge information explicit instead of having to 765 * worry about people probing the ACPI areas, for example.. (Yes, it 766 * happens, and if you read the wrong ACPI register it will put the machine 767 * to sleep with no way of waking it up again. Bummer). 768 * 769 * ALI M7101: Two IO regions pointed to by words at 770 * 0xE0 (64 bytes of ACPI registers) 771 * 0xE2 (32 bytes of SMB registers) 772 */ 773 static void quirk_ali7101_acpi(struct pci_dev *dev) 774 { 775 quirk_io_region(dev, 0xE0, 64, PCI_BRIDGE_RESOURCES, "ali7101 ACPI"); 776 quirk_io_region(dev, 0xE2, 32, PCI_BRIDGE_RESOURCES+1, "ali7101 SMB"); 777 } 778 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101, quirk_ali7101_acpi); 779 780 static void piix4_io_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable) 781 { 782 u32 devres; 783 u32 mask, size, base; 784 785 pci_read_config_dword(dev, port, &devres); 786 if ((devres & enable) != enable) 787 return; 788 mask = (devres >> 16) & 15; 789 base = devres & 0xffff; 790 size = 16; 791 for (;;) { 792 unsigned int bit = size >> 1; 793 if ((bit & mask) == bit) 794 break; 795 size = bit; 796 } 797 /* 798 * For now we only print it out. Eventually we'll want to 799 * reserve it (at least if it's in the 0x1000+ range), but 800 * let's get enough confirmation reports first. 801 */ 802 base &= -size; 803 pci_info(dev, "%s PIO at %04x-%04x\n", name, base, base + size - 1); 804 } 805 806 static void piix4_mem_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable) 807 { 808 u32 devres; 809 u32 mask, size, base; 810 811 pci_read_config_dword(dev, port, &devres); 812 if ((devres & enable) != enable) 813 return; 814 base = devres & 0xffff0000; 815 mask = (devres & 0x3f) << 16; 816 size = 128 << 16; 817 for (;;) { 818 unsigned int bit = size >> 1; 819 if ((bit & mask) == bit) 820 break; 821 size = bit; 822 } 823 824 /* 825 * For now we only print it out. Eventually we'll want to 826 * reserve it, but let's get enough confirmation reports first. 827 */ 828 base &= -size; 829 pci_info(dev, "%s MMIO at %04x-%04x\n", name, base, base + size - 1); 830 } 831 832 /* 833 * PIIX4 ACPI: Two IO regions pointed to by longwords at 834 * 0x40 (64 bytes of ACPI registers) 835 * 0x90 (16 bytes of SMB registers) 836 * and a few strange programmable PIIX4 device resources. 837 */ 838 static void quirk_piix4_acpi(struct pci_dev *dev) 839 { 840 u32 res_a; 841 842 quirk_io_region(dev, 0x40, 64, PCI_BRIDGE_RESOURCES, "PIIX4 ACPI"); 843 quirk_io_region(dev, 0x90, 16, PCI_BRIDGE_RESOURCES+1, "PIIX4 SMB"); 844 845 /* Device resource A has enables for some of the other ones */ 846 pci_read_config_dword(dev, 0x5c, &res_a); 847 848 piix4_io_quirk(dev, "PIIX4 devres B", 0x60, 3 << 21); 849 piix4_io_quirk(dev, "PIIX4 devres C", 0x64, 3 << 21); 850 851 /* Device resource D is just bitfields for static resources */ 852 853 /* Device 12 enabled? */ 854 if (res_a & (1 << 29)) { 855 piix4_io_quirk(dev, "PIIX4 devres E", 0x68, 1 << 20); 856 piix4_mem_quirk(dev, "PIIX4 devres F", 0x6c, 1 << 7); 857 } 858 /* Device 13 enabled? */ 859 if (res_a & (1 << 30)) { 860 piix4_io_quirk(dev, "PIIX4 devres G", 0x70, 1 << 20); 861 piix4_mem_quirk(dev, "PIIX4 devres H", 0x74, 1 << 7); 862 } 863 piix4_io_quirk(dev, "PIIX4 devres I", 0x78, 1 << 20); 864 piix4_io_quirk(dev, "PIIX4 devres J", 0x7c, 1 << 20); 865 } 866 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, quirk_piix4_acpi); 867 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443MX_3, quirk_piix4_acpi); 868 869 #define ICH_PMBASE 0x40 870 #define ICH_ACPI_CNTL 0x44 871 #define ICH4_ACPI_EN 0x10 872 #define ICH6_ACPI_EN 0x80 873 #define ICH4_GPIOBASE 0x58 874 #define ICH4_GPIO_CNTL 0x5c 875 #define ICH4_GPIO_EN 0x10 876 #define ICH6_GPIOBASE 0x48 877 #define ICH6_GPIO_CNTL 0x4c 878 #define ICH6_GPIO_EN 0x10 879 880 /* 881 * ICH4, ICH4-M, ICH5, ICH5-M ACPI: Three IO regions pointed to by longwords at 882 * 0x40 (128 bytes of ACPI, GPIO & TCO registers) 883 * 0x58 (64 bytes of GPIO I/O space) 884 */ 885 static void quirk_ich4_lpc_acpi(struct pci_dev *dev) 886 { 887 u8 enable; 888 889 /* 890 * The check for PCIBIOS_MIN_IO is to ensure we won't create a conflict 891 * with low legacy (and fixed) ports. We don't know the decoding 892 * priority and can't tell whether the legacy device or the one created 893 * here is really at that address. This happens on boards with broken 894 * BIOSes. 895 */ 896 pci_read_config_byte(dev, ICH_ACPI_CNTL, &enable); 897 if (enable & ICH4_ACPI_EN) 898 quirk_io_region(dev, ICH_PMBASE, 128, PCI_BRIDGE_RESOURCES, 899 "ICH4 ACPI/GPIO/TCO"); 900 901 pci_read_config_byte(dev, ICH4_GPIO_CNTL, &enable); 902 if (enable & ICH4_GPIO_EN) 903 quirk_io_region(dev, ICH4_GPIOBASE, 64, PCI_BRIDGE_RESOURCES+1, 904 "ICH4 GPIO"); 905 } 906 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, quirk_ich4_lpc_acpi); 907 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_0, quirk_ich4_lpc_acpi); 908 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, quirk_ich4_lpc_acpi); 909 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_10, quirk_ich4_lpc_acpi); 910 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, quirk_ich4_lpc_acpi); 911 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, quirk_ich4_lpc_acpi); 912 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, quirk_ich4_lpc_acpi); 913 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, quirk_ich4_lpc_acpi); 914 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, quirk_ich4_lpc_acpi); 915 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_1, quirk_ich4_lpc_acpi); 916 917 static void ich6_lpc_acpi_gpio(struct pci_dev *dev) 918 { 919 u8 enable; 920 921 pci_read_config_byte(dev, ICH_ACPI_CNTL, &enable); 922 if (enable & ICH6_ACPI_EN) 923 quirk_io_region(dev, ICH_PMBASE, 128, PCI_BRIDGE_RESOURCES, 924 "ICH6 ACPI/GPIO/TCO"); 925 926 pci_read_config_byte(dev, ICH6_GPIO_CNTL, &enable); 927 if (enable & ICH6_GPIO_EN) 928 quirk_io_region(dev, ICH6_GPIOBASE, 64, PCI_BRIDGE_RESOURCES+1, 929 "ICH6 GPIO"); 930 } 931 932 static void ich6_lpc_generic_decode(struct pci_dev *dev, unsigned int reg, 933 const char *name, int dynsize) 934 { 935 u32 val; 936 u32 size, base; 937 938 pci_read_config_dword(dev, reg, &val); 939 940 /* Enabled? */ 941 if (!(val & 1)) 942 return; 943 base = val & 0xfffc; 944 if (dynsize) { 945 /* 946 * This is not correct. It is 16, 32 or 64 bytes depending on 947 * register D31:F0:ADh bits 5:4. 948 * 949 * But this gets us at least _part_ of it. 950 */ 951 size = 16; 952 } else { 953 size = 128; 954 } 955 base &= ~(size-1); 956 957 /* 958 * Just print it out for now. We should reserve it after more 959 * debugging. 960 */ 961 pci_info(dev, "%s PIO at %04x-%04x\n", name, base, base+size-1); 962 } 963 964 static void quirk_ich6_lpc(struct pci_dev *dev) 965 { 966 /* Shared ACPI/GPIO decode with all ICH6+ */ 967 ich6_lpc_acpi_gpio(dev); 968 969 /* ICH6-specific generic IO decode */ 970 ich6_lpc_generic_decode(dev, 0x84, "LPC Generic IO decode 1", 0); 971 ich6_lpc_generic_decode(dev, 0x88, "LPC Generic IO decode 2", 1); 972 } 973 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_0, quirk_ich6_lpc); 974 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, quirk_ich6_lpc); 975 976 static void ich7_lpc_generic_decode(struct pci_dev *dev, unsigned int reg, 977 const char *name) 978 { 979 u32 val; 980 u32 mask, base; 981 982 pci_read_config_dword(dev, reg, &val); 983 984 /* Enabled? */ 985 if (!(val & 1)) 986 return; 987 988 /* IO base in bits 15:2, mask in bits 23:18, both are dword-based */ 989 base = val & 0xfffc; 990 mask = (val >> 16) & 0xfc; 991 mask |= 3; 992 993 /* 994 * Just print it out for now. We should reserve it after more 995 * debugging. 996 */ 997 pci_info(dev, "%s PIO at %04x (mask %04x)\n", name, base, mask); 998 } 999 1000 /* ICH7-10 has the same common LPC generic IO decode registers */ 1001 static void quirk_ich7_lpc(struct pci_dev *dev) 1002 { 1003 /* We share the common ACPI/GPIO decode with ICH6 */ 1004 ich6_lpc_acpi_gpio(dev); 1005 1006 /* And have 4 ICH7+ generic decodes */ 1007 ich7_lpc_generic_decode(dev, 0x84, "ICH7 LPC Generic IO decode 1"); 1008 ich7_lpc_generic_decode(dev, 0x88, "ICH7 LPC Generic IO decode 2"); 1009 ich7_lpc_generic_decode(dev, 0x8c, "ICH7 LPC Generic IO decode 3"); 1010 ich7_lpc_generic_decode(dev, 0x90, "ICH7 LPC Generic IO decode 4"); 1011 } 1012 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_0, quirk_ich7_lpc); 1013 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_1, quirk_ich7_lpc); 1014 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_31, quirk_ich7_lpc); 1015 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_0, quirk_ich7_lpc); 1016 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_2, quirk_ich7_lpc); 1017 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_3, quirk_ich7_lpc); 1018 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_1, quirk_ich7_lpc); 1019 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_4, quirk_ich7_lpc); 1020 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_2, quirk_ich7_lpc); 1021 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_4, quirk_ich7_lpc); 1022 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_7, quirk_ich7_lpc); 1023 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_8, quirk_ich7_lpc); 1024 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH10_1, quirk_ich7_lpc); 1025 1026 /* 1027 * VIA ACPI: One IO region pointed to by longword at 1028 * 0x48 or 0x20 (256 bytes of ACPI registers) 1029 */ 1030 static void quirk_vt82c586_acpi(struct pci_dev *dev) 1031 { 1032 if (dev->revision & 0x10) 1033 quirk_io_region(dev, 0x48, 256, PCI_BRIDGE_RESOURCES, 1034 "vt82c586 ACPI"); 1035 } 1036 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_vt82c586_acpi); 1037 1038 /* 1039 * VIA VT82C686 ACPI: Three IO region pointed to by (long)words at 1040 * 0x48 (256 bytes of ACPI registers) 1041 * 0x70 (128 bytes of hardware monitoring register) 1042 * 0x90 (16 bytes of SMB registers) 1043 */ 1044 static void quirk_vt82c686_acpi(struct pci_dev *dev) 1045 { 1046 quirk_vt82c586_acpi(dev); 1047 1048 quirk_io_region(dev, 0x70, 128, PCI_BRIDGE_RESOURCES+1, 1049 "vt82c686 HW-mon"); 1050 1051 quirk_io_region(dev, 0x90, 16, PCI_BRIDGE_RESOURCES+2, "vt82c686 SMB"); 1052 } 1053 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_vt82c686_acpi); 1054 1055 /* 1056 * VIA VT8235 ISA Bridge: Two IO regions pointed to by words at 1057 * 0x88 (128 bytes of power management registers) 1058 * 0xd0 (16 bytes of SMB registers) 1059 */ 1060 static void quirk_vt8235_acpi(struct pci_dev *dev) 1061 { 1062 quirk_io_region(dev, 0x88, 128, PCI_BRIDGE_RESOURCES, "vt8235 PM"); 1063 quirk_io_region(dev, 0xd0, 16, PCI_BRIDGE_RESOURCES+1, "vt8235 SMB"); 1064 } 1065 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_vt8235_acpi); 1066 1067 /* 1068 * TI XIO2000a PCIe-PCI Bridge erroneously reports it supports fast 1069 * back-to-back: Disable fast back-to-back on the secondary bus segment 1070 */ 1071 static void quirk_xio2000a(struct pci_dev *dev) 1072 { 1073 struct pci_dev *pdev; 1074 u16 command; 1075 1076 pci_warn(dev, "TI XIO2000a quirk detected; secondary bus fast back-to-back transfers disabled\n"); 1077 list_for_each_entry(pdev, &dev->subordinate->devices, bus_list) { 1078 pci_read_config_word(pdev, PCI_COMMAND, &command); 1079 if (command & PCI_COMMAND_FAST_BACK) 1080 pci_write_config_word(pdev, PCI_COMMAND, command & ~PCI_COMMAND_FAST_BACK); 1081 } 1082 } 1083 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_XIO2000A, 1084 quirk_xio2000a); 1085 1086 #ifdef CONFIG_X86_IO_APIC 1087 1088 #include <asm/io_apic.h> 1089 1090 /* 1091 * VIA 686A/B: If an IO-APIC is active, we need to route all on-chip 1092 * devices to the external APIC. 1093 * 1094 * TODO: When we have device-specific interrupt routers, this code will go 1095 * away from quirks. 1096 */ 1097 static void quirk_via_ioapic(struct pci_dev *dev) 1098 { 1099 u8 tmp; 1100 1101 if (nr_ioapics < 1) 1102 tmp = 0; /* nothing routed to external APIC */ 1103 else 1104 tmp = 0x1f; /* all known bits (4-0) routed to external APIC */ 1105 1106 pci_info(dev, "%s VIA external APIC routing\n", 1107 tmp ? "Enabling" : "Disabling"); 1108 1109 /* Offset 0x58: External APIC IRQ output control */ 1110 pci_write_config_byte(dev, 0x58, tmp); 1111 } 1112 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic); 1113 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic); 1114 1115 /* 1116 * VIA 8237: Some BIOSes don't set the 'Bypass APIC De-Assert Message' Bit. 1117 * This leads to doubled level interrupt rates. 1118 * Set this bit to get rid of cycle wastage. 1119 * Otherwise uncritical. 1120 */ 1121 static void quirk_via_vt8237_bypass_apic_deassert(struct pci_dev *dev) 1122 { 1123 u8 misc_control2; 1124 #define BYPASS_APIC_DEASSERT 8 1125 1126 pci_read_config_byte(dev, 0x5B, &misc_control2); 1127 if (!(misc_control2 & BYPASS_APIC_DEASSERT)) { 1128 pci_info(dev, "Bypassing VIA 8237 APIC De-Assert Message\n"); 1129 pci_write_config_byte(dev, 0x5B, misc_control2|BYPASS_APIC_DEASSERT); 1130 } 1131 } 1132 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_vt8237_bypass_apic_deassert); 1133 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_vt8237_bypass_apic_deassert); 1134 1135 /* 1136 * The AMD IO-APIC can hang the box when an APIC IRQ is masked. 1137 * We check all revs >= B0 (yet not in the pre production!) as the bug 1138 * is currently marked NoFix 1139 * 1140 * We have multiple reports of hangs with this chipset that went away with 1141 * noapic specified. For the moment we assume it's the erratum. We may be wrong 1142 * of course. However the advice is demonstrably good even if so. 1143 */ 1144 static void quirk_amd_ioapic(struct pci_dev *dev) 1145 { 1146 if (dev->revision >= 0x02) { 1147 pci_warn(dev, "I/O APIC: AMD Erratum #22 may be present. In the event of instability try\n"); 1148 pci_warn(dev, " : booting with the \"noapic\" option\n"); 1149 } 1150 } 1151 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7410, quirk_amd_ioapic); 1152 #endif /* CONFIG_X86_IO_APIC */ 1153 1154 #if defined(CONFIG_ARM64) && defined(CONFIG_PCI_ATS) 1155 1156 static void quirk_cavium_sriov_rnm_link(struct pci_dev *dev) 1157 { 1158 /* Fix for improper SR-IOV configuration on Cavium cn88xx RNM device */ 1159 if (dev->subsystem_device == 0xa118) 1160 dev->sriov->link = dev->devfn; 1161 } 1162 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CAVIUM, 0xa018, quirk_cavium_sriov_rnm_link); 1163 #endif 1164 1165 /* 1166 * Some settings of MMRBC can lead to data corruption so block changes. 1167 * See AMD 8131 HyperTransport PCI-X Tunnel Revision Guide 1168 */ 1169 static void quirk_amd_8131_mmrbc(struct pci_dev *dev) 1170 { 1171 if (dev->subordinate && dev->revision <= 0x12) { 1172 pci_info(dev, "AMD8131 rev %x detected; disabling PCI-X MMRBC\n", 1173 dev->revision); 1174 dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MMRBC; 1175 } 1176 } 1177 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_amd_8131_mmrbc); 1178 1179 /* 1180 * FIXME: it is questionable that quirk_via_acpi() is needed. It shows up 1181 * as an ISA bridge, and does not support the PCI_INTERRUPT_LINE register 1182 * at all. Therefore it seems like setting the pci_dev's IRQ to the value 1183 * of the ACPI SCI interrupt is only done for convenience. 1184 * -jgarzik 1185 */ 1186 static void quirk_via_acpi(struct pci_dev *d) 1187 { 1188 u8 irq; 1189 1190 /* VIA ACPI device: SCI IRQ line in PCI config byte 0x42 */ 1191 pci_read_config_byte(d, 0x42, &irq); 1192 irq &= 0xf; 1193 if (irq && (irq != 2)) 1194 d->irq = irq; 1195 } 1196 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_acpi); 1197 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_acpi); 1198 1199 /* VIA bridges which have VLink */ 1200 static int via_vlink_dev_lo = -1, via_vlink_dev_hi = 18; 1201 1202 static void quirk_via_bridge(struct pci_dev *dev) 1203 { 1204 /* See what bridge we have and find the device ranges */ 1205 switch (dev->device) { 1206 case PCI_DEVICE_ID_VIA_82C686: 1207 /* 1208 * The VT82C686 is special; it attaches to PCI and can have 1209 * any device number. All its subdevices are functions of 1210 * that single device. 1211 */ 1212 via_vlink_dev_lo = PCI_SLOT(dev->devfn); 1213 via_vlink_dev_hi = PCI_SLOT(dev->devfn); 1214 break; 1215 case PCI_DEVICE_ID_VIA_8237: 1216 case PCI_DEVICE_ID_VIA_8237A: 1217 via_vlink_dev_lo = 15; 1218 break; 1219 case PCI_DEVICE_ID_VIA_8235: 1220 via_vlink_dev_lo = 16; 1221 break; 1222 case PCI_DEVICE_ID_VIA_8231: 1223 case PCI_DEVICE_ID_VIA_8233_0: 1224 case PCI_DEVICE_ID_VIA_8233A: 1225 case PCI_DEVICE_ID_VIA_8233C_0: 1226 via_vlink_dev_lo = 17; 1227 break; 1228 } 1229 } 1230 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_bridge); 1231 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, quirk_via_bridge); 1232 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233_0, quirk_via_bridge); 1233 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233A, quirk_via_bridge); 1234 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233C_0, quirk_via_bridge); 1235 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_via_bridge); 1236 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_bridge); 1237 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237A, quirk_via_bridge); 1238 1239 /* 1240 * quirk_via_vlink - VIA VLink IRQ number update 1241 * @dev: PCI device 1242 * 1243 * If the device we are dealing with is on a PIC IRQ we need to ensure that 1244 * the IRQ line register which usually is not relevant for PCI cards, is 1245 * actually written so that interrupts get sent to the right place. 1246 * 1247 * We only do this on systems where a VIA south bridge was detected, and 1248 * only for VIA devices on the motherboard (see quirk_via_bridge above). 1249 */ 1250 static void quirk_via_vlink(struct pci_dev *dev) 1251 { 1252 u8 irq, new_irq; 1253 1254 /* Check if we have VLink at all */ 1255 if (via_vlink_dev_lo == -1) 1256 return; 1257 1258 new_irq = dev->irq; 1259 1260 /* Don't quirk interrupts outside the legacy IRQ range */ 1261 if (!new_irq || new_irq > 15) 1262 return; 1263 1264 /* Internal device ? */ 1265 if (dev->bus->number != 0 || PCI_SLOT(dev->devfn) > via_vlink_dev_hi || 1266 PCI_SLOT(dev->devfn) < via_vlink_dev_lo) 1267 return; 1268 1269 /* 1270 * This is an internal VLink device on a PIC interrupt. The BIOS 1271 * ought to have set this but may not have, so we redo it. 1272 */ 1273 pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq); 1274 if (new_irq != irq) { 1275 pci_info(dev, "VIA VLink IRQ fixup, from %d to %d\n", 1276 irq, new_irq); 1277 udelay(15); /* unknown if delay really needed */ 1278 pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq); 1279 } 1280 } 1281 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_vlink); 1282 1283 /* 1284 * VIA VT82C598 has its device ID settable and many BIOSes set it to the ID 1285 * of VT82C597 for backward compatibility. We need to switch it off to be 1286 * able to recognize the real type of the chip. 1287 */ 1288 static void quirk_vt82c598_id(struct pci_dev *dev) 1289 { 1290 pci_write_config_byte(dev, 0xfc, 0); 1291 pci_read_config_word(dev, PCI_DEVICE_ID, &dev->device); 1292 } 1293 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_vt82c598_id); 1294 1295 /* 1296 * CardBus controllers have a legacy base address that enables them to 1297 * respond as i82365 pcmcia controllers. We don't want them to do this 1298 * even if the Linux CardBus driver is not loaded, because the Linux i82365 1299 * driver does not (and should not) handle CardBus. 1300 */ 1301 static void quirk_cardbus_legacy(struct pci_dev *dev) 1302 { 1303 pci_write_config_dword(dev, PCI_CB_LEGACY_MODE_BASE, 0); 1304 } 1305 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID, 1306 PCI_CLASS_BRIDGE_CARDBUS, 8, quirk_cardbus_legacy); 1307 DECLARE_PCI_FIXUP_CLASS_RESUME_EARLY(PCI_ANY_ID, PCI_ANY_ID, 1308 PCI_CLASS_BRIDGE_CARDBUS, 8, quirk_cardbus_legacy); 1309 1310 /* 1311 * Following the PCI ordering rules is optional on the AMD762. I'm not sure 1312 * what the designers were smoking but let's not inhale... 1313 * 1314 * To be fair to AMD, it follows the spec by default, it's BIOS people who 1315 * turn it off! 1316 */ 1317 static void quirk_amd_ordering(struct pci_dev *dev) 1318 { 1319 u32 pcic; 1320 pci_read_config_dword(dev, 0x4C, &pcic); 1321 if ((pcic & 6) != 6) { 1322 pcic |= 6; 1323 pci_warn(dev, "BIOS failed to enable PCI standards compliance; fixing this error\n"); 1324 pci_write_config_dword(dev, 0x4C, pcic); 1325 pci_read_config_dword(dev, 0x84, &pcic); 1326 pcic |= (1 << 23); /* Required in this mode */ 1327 pci_write_config_dword(dev, 0x84, pcic); 1328 } 1329 } 1330 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering); 1331 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering); 1332 1333 /* 1334 * DreamWorks-provided workaround for Dunord I-3000 problem 1335 * 1336 * This card decodes and responds to addresses not apparently assigned to 1337 * it. We force a larger allocation to ensure that nothing gets put too 1338 * close to it. 1339 */ 1340 static void quirk_dunord(struct pci_dev *dev) 1341 { 1342 struct resource *r = &dev->resource[1]; 1343 1344 r->flags |= IORESOURCE_UNSET; 1345 r->start = 0; 1346 r->end = 0xffffff; 1347 } 1348 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_DUNORD, PCI_DEVICE_ID_DUNORD_I3000, quirk_dunord); 1349 1350 /* 1351 * i82380FB mobile docking controller: its PCI-to-PCI bridge is subtractive 1352 * decoding (transparent), and does indicate this in the ProgIf. 1353 * Unfortunately, the ProgIf value is wrong - 0x80 instead of 0x01. 1354 */ 1355 static void quirk_transparent_bridge(struct pci_dev *dev) 1356 { 1357 dev->transparent = 1; 1358 } 1359 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82380FB, quirk_transparent_bridge); 1360 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA, 0x605, quirk_transparent_bridge); 1361 1362 /* 1363 * Common misconfiguration of the MediaGX/Geode PCI master that will reduce 1364 * PCI bandwidth from 70MB/s to 25MB/s. See the GXM/GXLV/GX1 datasheets 1365 * found at http://www.national.com/analog for info on what these bits do. 1366 * <christer@weinigel.se> 1367 */ 1368 static void quirk_mediagx_master(struct pci_dev *dev) 1369 { 1370 u8 reg; 1371 1372 pci_read_config_byte(dev, 0x41, ®); 1373 if (reg & 2) { 1374 reg &= ~2; 1375 pci_info(dev, "Fixup for MediaGX/Geode Slave Disconnect Boundary (0x41=0x%02x)\n", 1376 reg); 1377 pci_write_config_byte(dev, 0x41, reg); 1378 } 1379 } 1380 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master); 1381 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master); 1382 1383 /* 1384 * Ensure C0 rev restreaming is off. This is normally done by the BIOS but 1385 * in the odd case it is not the results are corruption hence the presence 1386 * of a Linux check. 1387 */ 1388 static void quirk_disable_pxb(struct pci_dev *pdev) 1389 { 1390 u16 config; 1391 1392 if (pdev->revision != 0x04) /* Only C0 requires this */ 1393 return; 1394 pci_read_config_word(pdev, 0x40, &config); 1395 if (config & (1<<6)) { 1396 config &= ~(1<<6); 1397 pci_write_config_word(pdev, 0x40, config); 1398 pci_info(pdev, "C0 revision 450NX. Disabling PCI restreaming\n"); 1399 } 1400 } 1401 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb); 1402 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb); 1403 1404 static void quirk_amd_ide_mode(struct pci_dev *pdev) 1405 { 1406 /* set SBX00/Hudson-2 SATA in IDE mode to AHCI mode */ 1407 u8 tmp; 1408 1409 pci_read_config_byte(pdev, PCI_CLASS_DEVICE, &tmp); 1410 if (tmp == 0x01) { 1411 pci_read_config_byte(pdev, 0x40, &tmp); 1412 pci_write_config_byte(pdev, 0x40, tmp|1); 1413 pci_write_config_byte(pdev, 0x9, 1); 1414 pci_write_config_byte(pdev, 0xa, 6); 1415 pci_write_config_byte(pdev, 0x40, tmp); 1416 1417 pdev->class = PCI_CLASS_STORAGE_SATA_AHCI; 1418 pci_info(pdev, "set SATA to AHCI mode\n"); 1419 } 1420 } 1421 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_amd_ide_mode); 1422 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_amd_ide_mode); 1423 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_amd_ide_mode); 1424 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_amd_ide_mode); 1425 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA_IDE, quirk_amd_ide_mode); 1426 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA_IDE, quirk_amd_ide_mode); 1427 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x7900, quirk_amd_ide_mode); 1428 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, 0x7900, quirk_amd_ide_mode); 1429 1430 /* Serverworks CSB5 IDE does not fully support native mode */ 1431 static void quirk_svwks_csb5ide(struct pci_dev *pdev) 1432 { 1433 u8 prog; 1434 pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); 1435 if (prog & 5) { 1436 prog &= ~5; 1437 pdev->class &= ~5; 1438 pci_write_config_byte(pdev, PCI_CLASS_PROG, prog); 1439 /* PCI layer will sort out resources */ 1440 } 1441 } 1442 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, quirk_svwks_csb5ide); 1443 1444 /* Intel 82801CAM ICH3-M datasheet says IDE modes must be the same */ 1445 static void quirk_ide_samemode(struct pci_dev *pdev) 1446 { 1447 u8 prog; 1448 1449 pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); 1450 1451 if (((prog & 1) && !(prog & 4)) || ((prog & 4) && !(prog & 1))) { 1452 pci_info(pdev, "IDE mode mismatch; forcing legacy mode\n"); 1453 prog &= ~5; 1454 pdev->class &= ~5; 1455 pci_write_config_byte(pdev, PCI_CLASS_PROG, prog); 1456 } 1457 } 1458 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, quirk_ide_samemode); 1459 1460 /* Some ATA devices break if put into D3 */ 1461 static void quirk_no_ata_d3(struct pci_dev *pdev) 1462 { 1463 pdev->dev_flags |= PCI_DEV_FLAGS_NO_D3; 1464 } 1465 /* Quirk the legacy ATA devices only. The AHCI ones are ok */ 1466 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_ANY_ID, 1467 PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3); 1468 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_ATI, PCI_ANY_ID, 1469 PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3); 1470 /* ALi loses some register settings that we cannot then restore */ 1471 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID, 1472 PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3); 1473 /* VIA comes back fine but we need to keep it alive or ACPI GTM failures 1474 occur when mode detecting */ 1475 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_VIA, PCI_ANY_ID, 1476 PCI_CLASS_STORAGE_IDE, 8, quirk_no_ata_d3); 1477 1478 /* 1479 * This was originally an Alpha-specific thing, but it really fits here. 1480 * The i82375 PCI/EISA bridge appears as non-classified. Fix that. 1481 */ 1482 static void quirk_eisa_bridge(struct pci_dev *dev) 1483 { 1484 dev->class = PCI_CLASS_BRIDGE_EISA << 8; 1485 } 1486 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82375, quirk_eisa_bridge); 1487 1488 /* 1489 * On ASUS P4B boards, the SMBus PCI Device within the ICH2/4 southbridge 1490 * is not activated. The myth is that Asus said that they do not want the 1491 * users to be irritated by just another PCI Device in the Win98 device 1492 * manager. (see the file prog/hotplug/README.p4b in the lm_sensors 1493 * package 2.7.0 for details) 1494 * 1495 * The SMBus PCI Device can be activated by setting a bit in the ICH LPC 1496 * bridge. Unfortunately, this device has no subvendor/subdevice ID. So it 1497 * becomes necessary to do this tweak in two steps -- the chosen trigger 1498 * is either the Host bridge (preferred) or on-board VGA controller. 1499 * 1500 * Note that we used to unhide the SMBus that way on Toshiba laptops 1501 * (Satellite A40 and Tecra M2) but then found that the thermal management 1502 * was done by SMM code, which could cause unsynchronized concurrent 1503 * accesses to the SMBus registers, with potentially bad effects. Thus you 1504 * should be very careful when adding new entries: if SMM is accessing the 1505 * Intel SMBus, this is a very good reason to leave it hidden. 1506 * 1507 * Likewise, many recent laptops use ACPI for thermal management. If the 1508 * ACPI DSDT code accesses the SMBus, then Linux should not access it 1509 * natively, and keeping the SMBus hidden is the right thing to do. If you 1510 * are about to add an entry in the table below, please first disassemble 1511 * the DSDT and double-check that there is no code accessing the SMBus. 1512 */ 1513 static int asus_hides_smbus; 1514 1515 static void asus_hides_smbus_hostbridge(struct pci_dev *dev) 1516 { 1517 if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) { 1518 if (dev->device == PCI_DEVICE_ID_INTEL_82845_HB) 1519 switch (dev->subsystem_device) { 1520 case 0x8025: /* P4B-LX */ 1521 case 0x8070: /* P4B */ 1522 case 0x8088: /* P4B533 */ 1523 case 0x1626: /* L3C notebook */ 1524 asus_hides_smbus = 1; 1525 } 1526 else if (dev->device == PCI_DEVICE_ID_INTEL_82845G_HB) 1527 switch (dev->subsystem_device) { 1528 case 0x80b1: /* P4GE-V */ 1529 case 0x80b2: /* P4PE */ 1530 case 0x8093: /* P4B533-V */ 1531 asus_hides_smbus = 1; 1532 } 1533 else if (dev->device == PCI_DEVICE_ID_INTEL_82850_HB) 1534 switch (dev->subsystem_device) { 1535 case 0x8030: /* P4T533 */ 1536 asus_hides_smbus = 1; 1537 } 1538 else if (dev->device == PCI_DEVICE_ID_INTEL_7205_0) 1539 switch (dev->subsystem_device) { 1540 case 0x8070: /* P4G8X Deluxe */ 1541 asus_hides_smbus = 1; 1542 } 1543 else if (dev->device == PCI_DEVICE_ID_INTEL_E7501_MCH) 1544 switch (dev->subsystem_device) { 1545 case 0x80c9: /* PU-DLS */ 1546 asus_hides_smbus = 1; 1547 } 1548 else if (dev->device == PCI_DEVICE_ID_INTEL_82855GM_HB) 1549 switch (dev->subsystem_device) { 1550 case 0x1751: /* M2N notebook */ 1551 case 0x1821: /* M5N notebook */ 1552 case 0x1897: /* A6L notebook */ 1553 asus_hides_smbus = 1; 1554 } 1555 else if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 1556 switch (dev->subsystem_device) { 1557 case 0x184b: /* W1N notebook */ 1558 case 0x186a: /* M6Ne notebook */ 1559 asus_hides_smbus = 1; 1560 } 1561 else if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB) 1562 switch (dev->subsystem_device) { 1563 case 0x80f2: /* P4P800-X */ 1564 asus_hides_smbus = 1; 1565 } 1566 else if (dev->device == PCI_DEVICE_ID_INTEL_82915GM_HB) 1567 switch (dev->subsystem_device) { 1568 case 0x1882: /* M6V notebook */ 1569 case 0x1977: /* A6VA notebook */ 1570 asus_hides_smbus = 1; 1571 } 1572 } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_HP)) { 1573 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 1574 switch (dev->subsystem_device) { 1575 case 0x088C: /* HP Compaq nc8000 */ 1576 case 0x0890: /* HP Compaq nc6000 */ 1577 asus_hides_smbus = 1; 1578 } 1579 else if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB) 1580 switch (dev->subsystem_device) { 1581 case 0x12bc: /* HP D330L */ 1582 case 0x12bd: /* HP D530 */ 1583 case 0x006a: /* HP Compaq nx9500 */ 1584 asus_hides_smbus = 1; 1585 } 1586 else if (dev->device == PCI_DEVICE_ID_INTEL_82875_HB) 1587 switch (dev->subsystem_device) { 1588 case 0x12bf: /* HP xw4100 */ 1589 asus_hides_smbus = 1; 1590 } 1591 } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG)) { 1592 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 1593 switch (dev->subsystem_device) { 1594 case 0xC00C: /* Samsung P35 notebook */ 1595 asus_hides_smbus = 1; 1596 } 1597 } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_COMPAQ)) { 1598 if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) 1599 switch (dev->subsystem_device) { 1600 case 0x0058: /* Compaq Evo N620c */ 1601 asus_hides_smbus = 1; 1602 } 1603 else if (dev->device == PCI_DEVICE_ID_INTEL_82810_IG3) 1604 switch (dev->subsystem_device) { 1605 case 0xB16C: /* Compaq Deskpro EP 401963-001 (PCA# 010174) */ 1606 /* Motherboard doesn't have Host bridge 1607 * subvendor/subdevice IDs, therefore checking 1608 * its on-board VGA controller */ 1609 asus_hides_smbus = 1; 1610 } 1611 else if (dev->device == PCI_DEVICE_ID_INTEL_82801DB_2) 1612 switch (dev->subsystem_device) { 1613 case 0x00b8: /* Compaq Evo D510 CMT */ 1614 case 0x00b9: /* Compaq Evo D510 SFF */ 1615 case 0x00ba: /* Compaq Evo D510 USDT */ 1616 /* Motherboard doesn't have Host bridge 1617 * subvendor/subdevice IDs and on-board VGA 1618 * controller is disabled if an AGP card is 1619 * inserted, therefore checking USB UHCI 1620 * Controller #1 */ 1621 asus_hides_smbus = 1; 1622 } 1623 else if (dev->device == PCI_DEVICE_ID_INTEL_82815_CGC) 1624 switch (dev->subsystem_device) { 1625 case 0x001A: /* Compaq Deskpro EN SSF P667 815E */ 1626 /* Motherboard doesn't have host bridge 1627 * subvendor/subdevice IDs, therefore checking 1628 * its on-board VGA controller */ 1629 asus_hides_smbus = 1; 1630 } 1631 } 1632 } 1633 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845_HB, asus_hides_smbus_hostbridge); 1634 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845G_HB, asus_hides_smbus_hostbridge); 1635 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82850_HB, asus_hides_smbus_hostbridge); 1636 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB, asus_hides_smbus_hostbridge); 1637 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82875_HB, asus_hides_smbus_hostbridge); 1638 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_7205_0, asus_hides_smbus_hostbridge); 1639 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7501_MCH, asus_hides_smbus_hostbridge); 1640 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855PM_HB, asus_hides_smbus_hostbridge); 1641 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855GM_HB, asus_hides_smbus_hostbridge); 1642 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82915GM_HB, asus_hides_smbus_hostbridge); 1643 1644 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82810_IG3, asus_hides_smbus_hostbridge); 1645 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_2, asus_hides_smbus_hostbridge); 1646 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82815_CGC, asus_hides_smbus_hostbridge); 1647 1648 static void asus_hides_smbus_lpc(struct pci_dev *dev) 1649 { 1650 u16 val; 1651 1652 if (likely(!asus_hides_smbus)) 1653 return; 1654 1655 pci_read_config_word(dev, 0xF2, &val); 1656 if (val & 0x8) { 1657 pci_write_config_word(dev, 0xF2, val & (~0x8)); 1658 pci_read_config_word(dev, 0xF2, &val); 1659 if (val & 0x8) 1660 pci_info(dev, "i801 SMBus device continues to play 'hide and seek'! 0x%x\n", 1661 val); 1662 else 1663 pci_info(dev, "Enabled i801 SMBus device\n"); 1664 } 1665 } 1666 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, asus_hides_smbus_lpc); 1667 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc); 1668 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc); 1669 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, asus_hides_smbus_lpc); 1670 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc); 1671 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc); 1672 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc); 1673 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, asus_hides_smbus_lpc); 1674 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc); 1675 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc); 1676 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, asus_hides_smbus_lpc); 1677 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc); 1678 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc); 1679 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc); 1680 1681 /* It appears we just have one such device. If not, we have a warning */ 1682 static void __iomem *asus_rcba_base; 1683 static void asus_hides_smbus_lpc_ich6_suspend(struct pci_dev *dev) 1684 { 1685 u32 rcba; 1686 1687 if (likely(!asus_hides_smbus)) 1688 return; 1689 WARN_ON(asus_rcba_base); 1690 1691 pci_read_config_dword(dev, 0xF0, &rcba); 1692 /* use bits 31:14, 16 kB aligned */ 1693 asus_rcba_base = ioremap(rcba & 0xFFFFC000, 0x4000); 1694 if (asus_rcba_base == NULL) 1695 return; 1696 } 1697 1698 static void asus_hides_smbus_lpc_ich6_resume_early(struct pci_dev *dev) 1699 { 1700 u32 val; 1701 1702 if (likely(!asus_hides_smbus || !asus_rcba_base)) 1703 return; 1704 1705 /* read the Function Disable register, dword mode only */ 1706 val = readl(asus_rcba_base + 0x3418); 1707 1708 /* enable the SMBus device */ 1709 writel(val & 0xFFFFFFF7, asus_rcba_base + 0x3418); 1710 } 1711 1712 static void asus_hides_smbus_lpc_ich6_resume(struct pci_dev *dev) 1713 { 1714 if (likely(!asus_hides_smbus || !asus_rcba_base)) 1715 return; 1716 1717 iounmap(asus_rcba_base); 1718 asus_rcba_base = NULL; 1719 pci_info(dev, "Enabled ICH6/i801 SMBus device\n"); 1720 } 1721 1722 static void asus_hides_smbus_lpc_ich6(struct pci_dev *dev) 1723 { 1724 asus_hides_smbus_lpc_ich6_suspend(dev); 1725 asus_hides_smbus_lpc_ich6_resume_early(dev); 1726 asus_hides_smbus_lpc_ich6_resume(dev); 1727 } 1728 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6); 1729 DECLARE_PCI_FIXUP_SUSPEND(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_suspend); 1730 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_resume); 1731 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_resume_early); 1732 1733 /* SiS 96x south bridge: BIOS typically hides SMBus device... */ 1734 static void quirk_sis_96x_smbus(struct pci_dev *dev) 1735 { 1736 u8 val = 0; 1737 pci_read_config_byte(dev, 0x77, &val); 1738 if (val & 0x10) { 1739 pci_info(dev, "Enabling SiS 96x SMBus\n"); 1740 pci_write_config_byte(dev, 0x77, val & ~0x10); 1741 } 1742 } 1743 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus); 1744 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus); 1745 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus); 1746 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus); 1747 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus); 1748 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus); 1749 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus); 1750 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus); 1751 1752 /* 1753 * ... This is further complicated by the fact that some SiS96x south 1754 * bridges pretend to be 85C503/5513 instead. In that case see if we 1755 * spotted a compatible north bridge to make sure. 1756 * (pci_find_device() doesn't work yet) 1757 * 1758 * We can also enable the sis96x bit in the discovery register.. 1759 */ 1760 #define SIS_DETECT_REGISTER 0x40 1761 1762 static void quirk_sis_503(struct pci_dev *dev) 1763 { 1764 u8 reg; 1765 u16 devid; 1766 1767 pci_read_config_byte(dev, SIS_DETECT_REGISTER, ®); 1768 pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg | (1 << 6)); 1769 pci_read_config_word(dev, PCI_DEVICE_ID, &devid); 1770 if (((devid & 0xfff0) != 0x0960) && (devid != 0x0018)) { 1771 pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg); 1772 return; 1773 } 1774 1775 /* 1776 * Ok, it now shows up as a 96x. Run the 96x quirk by hand in case 1777 * it has already been processed. (Depends on link order, which is 1778 * apparently not guaranteed) 1779 */ 1780 dev->device = devid; 1781 quirk_sis_96x_smbus(dev); 1782 } 1783 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503); 1784 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503); 1785 1786 /* 1787 * On ASUS A8V and A8V Deluxe boards, the onboard AC97 audio controller 1788 * and MC97 modem controller are disabled when a second PCI soundcard is 1789 * present. This patch, tweaking the VT8237 ISA bridge, enables them. 1790 * -- bjd 1791 */ 1792 static void asus_hides_ac97_lpc(struct pci_dev *dev) 1793 { 1794 u8 val; 1795 int asus_hides_ac97 = 0; 1796 1797 if (likely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) { 1798 if (dev->device == PCI_DEVICE_ID_VIA_8237) 1799 asus_hides_ac97 = 1; 1800 } 1801 1802 if (!asus_hides_ac97) 1803 return; 1804 1805 pci_read_config_byte(dev, 0x50, &val); 1806 if (val & 0xc0) { 1807 pci_write_config_byte(dev, 0x50, val & (~0xc0)); 1808 pci_read_config_byte(dev, 0x50, &val); 1809 if (val & 0xc0) 1810 pci_info(dev, "Onboard AC97/MC97 devices continue to play 'hide and seek'! 0x%x\n", 1811 val); 1812 else 1813 pci_info(dev, "Enabled onboard AC97/MC97 devices\n"); 1814 } 1815 } 1816 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, asus_hides_ac97_lpc); 1817 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, asus_hides_ac97_lpc); 1818 1819 #if defined(CONFIG_ATA) || defined(CONFIG_ATA_MODULE) 1820 1821 /* 1822 * If we are using libata we can drive this chip properly but must do this 1823 * early on to make the additional device appear during the PCI scanning. 1824 */ 1825 static void quirk_jmicron_ata(struct pci_dev *pdev) 1826 { 1827 u32 conf1, conf5, class; 1828 u8 hdr; 1829 1830 /* Only poke fn 0 */ 1831 if (PCI_FUNC(pdev->devfn)) 1832 return; 1833 1834 pci_read_config_dword(pdev, 0x40, &conf1); 1835 pci_read_config_dword(pdev, 0x80, &conf5); 1836 1837 conf1 &= ~0x00CFF302; /* Clear bit 1, 8, 9, 12-19, 22, 23 */ 1838 conf5 &= ~(1 << 24); /* Clear bit 24 */ 1839 1840 switch (pdev->device) { 1841 case PCI_DEVICE_ID_JMICRON_JMB360: /* SATA single port */ 1842 case PCI_DEVICE_ID_JMICRON_JMB362: /* SATA dual ports */ 1843 case PCI_DEVICE_ID_JMICRON_JMB364: /* SATA dual ports */ 1844 /* The controller should be in single function ahci mode */ 1845 conf1 |= 0x0002A100; /* Set 8, 13, 15, 17 */ 1846 break; 1847 1848 case PCI_DEVICE_ID_JMICRON_JMB365: 1849 case PCI_DEVICE_ID_JMICRON_JMB366: 1850 /* Redirect IDE second PATA port to the right spot */ 1851 conf5 |= (1 << 24); 1852 fallthrough; 1853 case PCI_DEVICE_ID_JMICRON_JMB361: 1854 case PCI_DEVICE_ID_JMICRON_JMB363: 1855 case PCI_DEVICE_ID_JMICRON_JMB369: 1856 /* Enable dual function mode, AHCI on fn 0, IDE fn1 */ 1857 /* Set the class codes correctly and then direct IDE 0 */ 1858 conf1 |= 0x00C2A1B3; /* Set 0, 1, 4, 5, 7, 8, 13, 15, 17, 22, 23 */ 1859 break; 1860 1861 case PCI_DEVICE_ID_JMICRON_JMB368: 1862 /* The controller should be in single function IDE mode */ 1863 conf1 |= 0x00C00000; /* Set 22, 23 */ 1864 break; 1865 } 1866 1867 pci_write_config_dword(pdev, 0x40, conf1); 1868 pci_write_config_dword(pdev, 0x80, conf5); 1869 1870 /* Update pdev accordingly */ 1871 pci_read_config_byte(pdev, PCI_HEADER_TYPE, &hdr); 1872 pdev->hdr_type = hdr & PCI_HEADER_TYPE_MASK; 1873 pdev->multifunction = FIELD_GET(PCI_HEADER_TYPE_MFD, hdr); 1874 1875 pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class); 1876 pdev->class = class >> 8; 1877 } 1878 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata); 1879 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata); 1880 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata); 1881 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata); 1882 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB364, quirk_jmicron_ata); 1883 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata); 1884 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata); 1885 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata); 1886 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB369, quirk_jmicron_ata); 1887 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata); 1888 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata); 1889 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata); 1890 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata); 1891 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB364, quirk_jmicron_ata); 1892 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata); 1893 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata); 1894 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata); 1895 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB369, quirk_jmicron_ata); 1896 1897 #endif 1898 1899 static void quirk_jmicron_async_suspend(struct pci_dev *dev) 1900 { 1901 if (dev->multifunction) { 1902 device_disable_async_suspend(&dev->dev); 1903 pci_info(dev, "async suspend disabled to avoid multi-function power-on ordering issue\n"); 1904 } 1905 } 1906 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE, 8, quirk_jmicron_async_suspend); 1907 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_CLASS_STORAGE_SATA_AHCI, 0, quirk_jmicron_async_suspend); 1908 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_JMICRON, 0x2362, quirk_jmicron_async_suspend); 1909 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_JMICRON, 0x236f, quirk_jmicron_async_suspend); 1910 1911 #ifdef CONFIG_X86_IO_APIC 1912 static void quirk_alder_ioapic(struct pci_dev *pdev) 1913 { 1914 int i; 1915 1916 if ((pdev->class >> 8) != 0xff00) 1917 return; 1918 1919 /* 1920 * The first BAR is the location of the IO-APIC... we must 1921 * not touch this (and it's already covered by the fixmap), so 1922 * forcibly insert it into the resource tree. 1923 */ 1924 if (pci_resource_start(pdev, 0) && pci_resource_len(pdev, 0)) 1925 insert_resource(&iomem_resource, &pdev->resource[0]); 1926 1927 /* 1928 * The next five BARs all seem to be rubbish, so just clean 1929 * them out. 1930 */ 1931 for (i = 1; i < PCI_STD_NUM_BARS; i++) 1932 memset(&pdev->resource[i], 0, sizeof(pdev->resource[i])); 1933 } 1934 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EESSC, quirk_alder_ioapic); 1935 #endif 1936 1937 static void quirk_no_msi(struct pci_dev *dev) 1938 { 1939 pci_info(dev, "avoiding MSI to work around a hardware defect\n"); 1940 dev->no_msi = 1; 1941 } 1942 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4386, quirk_no_msi); 1943 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4387, quirk_no_msi); 1944 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4388, quirk_no_msi); 1945 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4389, quirk_no_msi); 1946 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x438a, quirk_no_msi); 1947 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x438b, quirk_no_msi); 1948 1949 static void quirk_pcie_mch(struct pci_dev *pdev) 1950 { 1951 pdev->no_msi = 1; 1952 } 1953 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, quirk_pcie_mch); 1954 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7320_MCH, quirk_pcie_mch); 1955 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7525_MCH, quirk_pcie_mch); 1956 1957 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_HUAWEI, 0x1610, PCI_CLASS_BRIDGE_PCI, 8, quirk_pcie_mch); 1958 1959 /* 1960 * HiSilicon KunPeng920 and KunPeng930 have devices appear as PCI but are 1961 * actually on the AMBA bus. These fake PCI devices can support SVA via 1962 * SMMU stall feature, by setting dma-can-stall for ACPI platforms. 1963 * 1964 * Normally stalling must not be enabled for PCI devices, since it would 1965 * break the PCI requirement for free-flowing writes and may lead to 1966 * deadlock. We expect PCI devices to support ATS and PRI if they want to 1967 * be fault-tolerant, so there's no ACPI binding to describe anything else, 1968 * even when a "PCI" device turns out to be a regular old SoC device 1969 * dressed up as a RCiEP and normal rules don't apply. 1970 */ 1971 static void quirk_huawei_pcie_sva(struct pci_dev *pdev) 1972 { 1973 struct property_entry properties[] = { 1974 PROPERTY_ENTRY_BOOL("dma-can-stall"), 1975 {}, 1976 }; 1977 1978 if (pdev->revision != 0x21 && pdev->revision != 0x30) 1979 return; 1980 1981 pdev->pasid_no_tlp = 1; 1982 1983 /* 1984 * Set the dma-can-stall property on ACPI platforms. Device tree 1985 * can set it directly. 1986 */ 1987 if (!pdev->dev.of_node && 1988 device_create_managed_software_node(&pdev->dev, properties, NULL)) 1989 pci_warn(pdev, "could not add stall property"); 1990 } 1991 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_HUAWEI, 0xa250, quirk_huawei_pcie_sva); 1992 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_HUAWEI, 0xa251, quirk_huawei_pcie_sva); 1993 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_HUAWEI, 0xa255, quirk_huawei_pcie_sva); 1994 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_HUAWEI, 0xa256, quirk_huawei_pcie_sva); 1995 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_HUAWEI, 0xa258, quirk_huawei_pcie_sva); 1996 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_HUAWEI, 0xa259, quirk_huawei_pcie_sva); 1997 1998 /* 1999 * It's possible for the MSI to get corrupted if SHPC and ACPI are used 2000 * together on certain PXH-based systems. 2001 */ 2002 static void quirk_pcie_pxh(struct pci_dev *dev) 2003 { 2004 dev->no_msi = 1; 2005 pci_warn(dev, "PXH quirk detected; SHPC device MSI disabled\n"); 2006 } 2007 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_0, quirk_pcie_pxh); 2008 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_1, quirk_pcie_pxh); 2009 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_pcie_pxh); 2010 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_pcie_pxh); 2011 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_pcie_pxh); 2012 2013 /* 2014 * Some Intel PCI Express chipsets have trouble with downstream device 2015 * power management. 2016 */ 2017 static void quirk_intel_pcie_pm(struct pci_dev *dev) 2018 { 2019 pci_pm_d3hot_delay = 120; 2020 dev->no_d1d2 = 1; 2021 } 2022 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e2, quirk_intel_pcie_pm); 2023 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e3, quirk_intel_pcie_pm); 2024 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e4, quirk_intel_pcie_pm); 2025 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e5, quirk_intel_pcie_pm); 2026 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e6, quirk_intel_pcie_pm); 2027 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e7, quirk_intel_pcie_pm); 2028 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f7, quirk_intel_pcie_pm); 2029 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f8, quirk_intel_pcie_pm); 2030 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f9, quirk_intel_pcie_pm); 2031 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25fa, quirk_intel_pcie_pm); 2032 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2601, quirk_intel_pcie_pm); 2033 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2602, quirk_intel_pcie_pm); 2034 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2603, quirk_intel_pcie_pm); 2035 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2604, quirk_intel_pcie_pm); 2036 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2605, quirk_intel_pcie_pm); 2037 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2606, quirk_intel_pcie_pm); 2038 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2607, quirk_intel_pcie_pm); 2039 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2608, quirk_intel_pcie_pm); 2040 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2609, quirk_intel_pcie_pm); 2041 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260a, quirk_intel_pcie_pm); 2042 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260b, quirk_intel_pcie_pm); 2043 2044 static void quirk_d3hot_delay(struct pci_dev *dev, unsigned int delay) 2045 { 2046 if (dev->d3hot_delay >= delay) 2047 return; 2048 2049 dev->d3hot_delay = delay; 2050 pci_info(dev, "extending delay after power-on from D3hot to %d msec\n", 2051 dev->d3hot_delay); 2052 } 2053 2054 static void quirk_radeon_pm(struct pci_dev *dev) 2055 { 2056 if (dev->subsystem_vendor == PCI_VENDOR_ID_APPLE && 2057 dev->subsystem_device == 0x00e2) 2058 quirk_d3hot_delay(dev, 20); 2059 } 2060 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x6741, quirk_radeon_pm); 2061 2062 /* 2063 * NVIDIA Ampere-based HDA controllers can wedge the whole device if a bus 2064 * reset is performed too soon after transition to D0, extend d3hot_delay 2065 * to previous effective default for all NVIDIA HDA controllers. 2066 */ 2067 static void quirk_nvidia_hda_pm(struct pci_dev *dev) 2068 { 2069 quirk_d3hot_delay(dev, 20); 2070 } 2071 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, 2072 PCI_CLASS_MULTIMEDIA_HD_AUDIO, 8, 2073 quirk_nvidia_hda_pm); 2074 2075 /* 2076 * Ryzen5/7 XHCI controllers fail upon resume from runtime suspend or s2idle. 2077 * https://bugzilla.kernel.org/show_bug.cgi?id=205587 2078 * 2079 * The kernel attempts to transition these devices to D3cold, but that seems 2080 * to be ineffective on the platforms in question; the PCI device appears to 2081 * remain on in D3hot state. The D3hot-to-D0 transition then requires an 2082 * extended delay in order to succeed. 2083 */ 2084 static void quirk_ryzen_xhci_d3hot(struct pci_dev *dev) 2085 { 2086 quirk_d3hot_delay(dev, 20); 2087 } 2088 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x15e0, quirk_ryzen_xhci_d3hot); 2089 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x15e1, quirk_ryzen_xhci_d3hot); 2090 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x1639, quirk_ryzen_xhci_d3hot); 2091 2092 #ifdef CONFIG_X86_IO_APIC 2093 static int dmi_disable_ioapicreroute(const struct dmi_system_id *d) 2094 { 2095 noioapicreroute = 1; 2096 pr_info("%s detected: disable boot interrupt reroute\n", d->ident); 2097 2098 return 0; 2099 } 2100 2101 static const struct dmi_system_id boot_interrupt_dmi_table[] = { 2102 /* 2103 * Systems to exclude from boot interrupt reroute quirks 2104 */ 2105 { 2106 .callback = dmi_disable_ioapicreroute, 2107 .ident = "ASUSTek Computer INC. M2N-LR", 2108 .matches = { 2109 DMI_MATCH(DMI_SYS_VENDOR, "ASUSTek Computer INC."), 2110 DMI_MATCH(DMI_PRODUCT_NAME, "M2N-LR"), 2111 }, 2112 }, 2113 {} 2114 }; 2115 2116 /* 2117 * Boot interrupts on some chipsets cannot be turned off. For these chipsets, 2118 * remap the original interrupt in the Linux kernel to the boot interrupt, so 2119 * that a PCI device's interrupt handler is installed on the boot interrupt 2120 * line instead. 2121 */ 2122 static void quirk_reroute_to_boot_interrupts_intel(struct pci_dev *dev) 2123 { 2124 dmi_check_system(boot_interrupt_dmi_table); 2125 if (noioapicquirk || noioapicreroute) 2126 return; 2127 2128 dev->irq_reroute_variant = INTEL_IRQ_REROUTE_VARIANT; 2129 pci_info(dev, "rerouting interrupts for [%04x:%04x]\n", 2130 dev->vendor, dev->device); 2131 } 2132 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_0, quirk_reroute_to_boot_interrupts_intel); 2133 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_1, quirk_reroute_to_boot_interrupts_intel); 2134 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, quirk_reroute_to_boot_interrupts_intel); 2135 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_reroute_to_boot_interrupts_intel); 2136 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_reroute_to_boot_interrupts_intel); 2137 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_reroute_to_boot_interrupts_intel); 2138 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_0, quirk_reroute_to_boot_interrupts_intel); 2139 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_1, quirk_reroute_to_boot_interrupts_intel); 2140 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_0, quirk_reroute_to_boot_interrupts_intel); 2141 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_1, quirk_reroute_to_boot_interrupts_intel); 2142 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, quirk_reroute_to_boot_interrupts_intel); 2143 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_reroute_to_boot_interrupts_intel); 2144 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_reroute_to_boot_interrupts_intel); 2145 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_reroute_to_boot_interrupts_intel); 2146 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_0, quirk_reroute_to_boot_interrupts_intel); 2147 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_1, quirk_reroute_to_boot_interrupts_intel); 2148 2149 /* 2150 * On some chipsets we can disable the generation of legacy INTx boot 2151 * interrupts. 2152 */ 2153 2154 /* 2155 * IO-APIC1 on 6300ESB generates boot interrupts, see Intel order no 2156 * 300641-004US, section 5.7.3. 2157 * 2158 * Core IO on Xeon E5 1600/2600/4600, see Intel order no 326509-003. 2159 * Core IO on Xeon E5 v2, see Intel order no 329188-003. 2160 * Core IO on Xeon E7 v2, see Intel order no 329595-002. 2161 * Core IO on Xeon E5 v3, see Intel order no 330784-003. 2162 * Core IO on Xeon E7 v3, see Intel order no 332315-001US. 2163 * Core IO on Xeon E5 v4, see Intel order no 333810-002US. 2164 * Core IO on Xeon E7 v4, see Intel order no 332315-001US. 2165 * Core IO on Xeon D-1500, see Intel order no 332051-001. 2166 * Core IO on Xeon Scalable, see Intel order no 610950. 2167 */ 2168 #define INTEL_6300_IOAPIC_ABAR 0x40 /* Bus 0, Dev 29, Func 5 */ 2169 #define INTEL_6300_DISABLE_BOOT_IRQ (1<<14) 2170 2171 #define INTEL_CIPINTRC_CFG_OFFSET 0x14C /* Bus 0, Dev 5, Func 0 */ 2172 #define INTEL_CIPINTRC_DIS_INTX_ICH (1<<25) 2173 2174 static void quirk_disable_intel_boot_interrupt(struct pci_dev *dev) 2175 { 2176 u16 pci_config_word; 2177 u32 pci_config_dword; 2178 2179 if (noioapicquirk) 2180 return; 2181 2182 switch (dev->device) { 2183 case PCI_DEVICE_ID_INTEL_ESB_10: 2184 pci_read_config_word(dev, INTEL_6300_IOAPIC_ABAR, 2185 &pci_config_word); 2186 pci_config_word |= INTEL_6300_DISABLE_BOOT_IRQ; 2187 pci_write_config_word(dev, INTEL_6300_IOAPIC_ABAR, 2188 pci_config_word); 2189 break; 2190 case 0x3c28: /* Xeon E5 1600/2600/4600 */ 2191 case 0x0e28: /* Xeon E5/E7 V2 */ 2192 case 0x2f28: /* Xeon E5/E7 V3,V4 */ 2193 case 0x6f28: /* Xeon D-1500 */ 2194 case 0x2034: /* Xeon Scalable Family */ 2195 pci_read_config_dword(dev, INTEL_CIPINTRC_CFG_OFFSET, 2196 &pci_config_dword); 2197 pci_config_dword |= INTEL_CIPINTRC_DIS_INTX_ICH; 2198 pci_write_config_dword(dev, INTEL_CIPINTRC_CFG_OFFSET, 2199 pci_config_dword); 2200 break; 2201 default: 2202 return; 2203 } 2204 pci_info(dev, "disabled boot interrupts on device [%04x:%04x]\n", 2205 dev->vendor, dev->device); 2206 } 2207 /* 2208 * Device 29 Func 5 Device IDs of IO-APIC 2209 * containing ABAR—APIC1 Alternate Base Address Register 2210 */ 2211 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_10, 2212 quirk_disable_intel_boot_interrupt); 2213 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_10, 2214 quirk_disable_intel_boot_interrupt); 2215 2216 /* 2217 * Device 5 Func 0 Device IDs of Core IO modules/hubs 2218 * containing Coherent Interface Protocol Interrupt Control 2219 * 2220 * Device IDs obtained from volume 2 datasheets of commented 2221 * families above. 2222 */ 2223 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x3c28, 2224 quirk_disable_intel_boot_interrupt); 2225 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0e28, 2226 quirk_disable_intel_boot_interrupt); 2227 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2f28, 2228 quirk_disable_intel_boot_interrupt); 2229 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x6f28, 2230 quirk_disable_intel_boot_interrupt); 2231 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2034, 2232 quirk_disable_intel_boot_interrupt); 2233 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, 0x3c28, 2234 quirk_disable_intel_boot_interrupt); 2235 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, 0x0e28, 2236 quirk_disable_intel_boot_interrupt); 2237 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, 0x2f28, 2238 quirk_disable_intel_boot_interrupt); 2239 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, 0x6f28, 2240 quirk_disable_intel_boot_interrupt); 2241 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, 0x2034, 2242 quirk_disable_intel_boot_interrupt); 2243 2244 /* Disable boot interrupts on HT-1000 */ 2245 #define BC_HT1000_FEATURE_REG 0x64 2246 #define BC_HT1000_PIC_REGS_ENABLE (1<<0) 2247 #define BC_HT1000_MAP_IDX 0xC00 2248 #define BC_HT1000_MAP_DATA 0xC01 2249 2250 static void quirk_disable_broadcom_boot_interrupt(struct pci_dev *dev) 2251 { 2252 u32 pci_config_dword; 2253 u8 irq; 2254 2255 if (noioapicquirk) 2256 return; 2257 2258 pci_read_config_dword(dev, BC_HT1000_FEATURE_REG, &pci_config_dword); 2259 pci_write_config_dword(dev, BC_HT1000_FEATURE_REG, pci_config_dword | 2260 BC_HT1000_PIC_REGS_ENABLE); 2261 2262 for (irq = 0x10; irq < 0x10 + 32; irq++) { 2263 outb(irq, BC_HT1000_MAP_IDX); 2264 outb(0x00, BC_HT1000_MAP_DATA); 2265 } 2266 2267 pci_write_config_dword(dev, BC_HT1000_FEATURE_REG, pci_config_dword); 2268 2269 pci_info(dev, "disabled boot interrupts on device [%04x:%04x]\n", 2270 dev->vendor, dev->device); 2271 } 2272 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000SB, quirk_disable_broadcom_boot_interrupt); 2273 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000SB, quirk_disable_broadcom_boot_interrupt); 2274 2275 /* Disable boot interrupts on AMD and ATI chipsets */ 2276 2277 /* 2278 * NOIOAMODE needs to be disabled to disable "boot interrupts". For AMD 8131 2279 * rev. A0 and B0, NOIOAMODE needs to be disabled anyway to fix IO-APIC mode 2280 * (due to an erratum). 2281 */ 2282 #define AMD_813X_MISC 0x40 2283 #define AMD_813X_NOIOAMODE (1<<0) 2284 #define AMD_813X_REV_B1 0x12 2285 #define AMD_813X_REV_B2 0x13 2286 2287 static void quirk_disable_amd_813x_boot_interrupt(struct pci_dev *dev) 2288 { 2289 u32 pci_config_dword; 2290 2291 if (noioapicquirk) 2292 return; 2293 if ((dev->revision == AMD_813X_REV_B1) || 2294 (dev->revision == AMD_813X_REV_B2)) 2295 return; 2296 2297 pci_read_config_dword(dev, AMD_813X_MISC, &pci_config_dword); 2298 pci_config_dword &= ~AMD_813X_NOIOAMODE; 2299 pci_write_config_dword(dev, AMD_813X_MISC, pci_config_dword); 2300 2301 pci_info(dev, "disabled boot interrupts on device [%04x:%04x]\n", 2302 dev->vendor, dev->device); 2303 } 2304 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_amd_813x_boot_interrupt); 2305 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_amd_813x_boot_interrupt); 2306 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, quirk_disable_amd_813x_boot_interrupt); 2307 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, quirk_disable_amd_813x_boot_interrupt); 2308 2309 #define AMD_8111_PCI_IRQ_ROUTING 0x56 2310 2311 static void quirk_disable_amd_8111_boot_interrupt(struct pci_dev *dev) 2312 { 2313 u16 pci_config_word; 2314 2315 if (noioapicquirk) 2316 return; 2317 2318 pci_read_config_word(dev, AMD_8111_PCI_IRQ_ROUTING, &pci_config_word); 2319 if (!pci_config_word) { 2320 pci_info(dev, "boot interrupts on device [%04x:%04x] already disabled\n", 2321 dev->vendor, dev->device); 2322 return; 2323 } 2324 pci_write_config_word(dev, AMD_8111_PCI_IRQ_ROUTING, 0); 2325 pci_info(dev, "disabled boot interrupts on device [%04x:%04x]\n", 2326 dev->vendor, dev->device); 2327 } 2328 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS, quirk_disable_amd_8111_boot_interrupt); 2329 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS, quirk_disable_amd_8111_boot_interrupt); 2330 #endif /* CONFIG_X86_IO_APIC */ 2331 2332 /* 2333 * Toshiba TC86C001 IDE controller reports the standard 8-byte BAR0 size 2334 * but the PIO transfers won't work if BAR0 falls at the odd 8 bytes. 2335 * Re-allocate the region if needed... 2336 */ 2337 static void quirk_tc86c001_ide(struct pci_dev *dev) 2338 { 2339 struct resource *r = &dev->resource[0]; 2340 2341 if (r->start & 0x8) { 2342 r->flags |= IORESOURCE_UNSET; 2343 r->start = 0; 2344 r->end = 0xf; 2345 } 2346 } 2347 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA_2, 2348 PCI_DEVICE_ID_TOSHIBA_TC86C001_IDE, 2349 quirk_tc86c001_ide); 2350 2351 /* 2352 * PLX PCI 9050 PCI Target bridge controller has an erratum that prevents the 2353 * local configuration registers accessible via BAR0 (memory) or BAR1 (i/o) 2354 * being read correctly if bit 7 of the base address is set. 2355 * The BAR0 or BAR1 region may be disabled (size 0) or enabled (size 128). 2356 * Re-allocate the regions to a 256-byte boundary if necessary. 2357 */ 2358 static void quirk_plx_pci9050(struct pci_dev *dev) 2359 { 2360 unsigned int bar; 2361 2362 /* Fixed in revision 2 (PCI 9052). */ 2363 if (dev->revision >= 2) 2364 return; 2365 for (bar = 0; bar <= 1; bar++) 2366 if (pci_resource_len(dev, bar) == 0x80 && 2367 (pci_resource_start(dev, bar) & 0x80)) { 2368 struct resource *r = &dev->resource[bar]; 2369 pci_info(dev, "Re-allocating PLX PCI 9050 BAR %u to length 256 to avoid bit 7 bug\n", 2370 bar); 2371 r->flags |= IORESOURCE_UNSET; 2372 r->start = 0; 2373 r->end = 0xff; 2374 } 2375 } 2376 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050, 2377 quirk_plx_pci9050); 2378 /* 2379 * The following Meilhaus (vendor ID 0x1402) device IDs (amongst others) 2380 * may be using the PLX PCI 9050: 0x0630, 0x0940, 0x0950, 0x0960, 0x100b, 2381 * 0x1400, 0x140a, 0x140b, 0x14e0, 0x14ea, 0x14eb, 0x1604, 0x1608, 0x160c, 2382 * 0x168f, 0x2000, 0x2600, 0x3000, 0x810a, 0x810b. 2383 * 2384 * Currently, device IDs 0x2000 and 0x2600 are used by the Comedi "me_daq" 2385 * driver. 2386 */ 2387 DECLARE_PCI_FIXUP_HEADER(0x1402, 0x2000, quirk_plx_pci9050); 2388 DECLARE_PCI_FIXUP_HEADER(0x1402, 0x2600, quirk_plx_pci9050); 2389 2390 static void quirk_netmos(struct pci_dev *dev) 2391 { 2392 unsigned int num_parallel = (dev->subsystem_device & 0xf0) >> 4; 2393 unsigned int num_serial = dev->subsystem_device & 0xf; 2394 2395 /* 2396 * These Netmos parts are multiport serial devices with optional 2397 * parallel ports. Even when parallel ports are present, they 2398 * are identified as class SERIAL, which means the serial driver 2399 * will claim them. To prevent this, mark them as class OTHER. 2400 * These combo devices should be claimed by parport_serial. 2401 * 2402 * The subdevice ID is of the form 0x00PS, where <P> is the number 2403 * of parallel ports and <S> is the number of serial ports. 2404 */ 2405 switch (dev->device) { 2406 case PCI_DEVICE_ID_NETMOS_9835: 2407 /* Well, this rule doesn't hold for the following 9835 device */ 2408 if (dev->subsystem_vendor == PCI_VENDOR_ID_IBM && 2409 dev->subsystem_device == 0x0299) 2410 return; 2411 fallthrough; 2412 case PCI_DEVICE_ID_NETMOS_9735: 2413 case PCI_DEVICE_ID_NETMOS_9745: 2414 case PCI_DEVICE_ID_NETMOS_9845: 2415 case PCI_DEVICE_ID_NETMOS_9855: 2416 if (num_parallel) { 2417 pci_info(dev, "Netmos %04x (%u parallel, %u serial); changing class SERIAL to OTHER (use parport_serial)\n", 2418 dev->device, num_parallel, num_serial); 2419 dev->class = (PCI_CLASS_COMMUNICATION_OTHER << 8) | 2420 (dev->class & 0xff); 2421 } 2422 } 2423 } 2424 DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_NETMOS, PCI_ANY_ID, 2425 PCI_CLASS_COMMUNICATION_SERIAL, 8, quirk_netmos); 2426 2427 static void quirk_e100_interrupt(struct pci_dev *dev) 2428 { 2429 u16 command, pmcsr; 2430 u8 __iomem *csr; 2431 u8 cmd_hi; 2432 2433 switch (dev->device) { 2434 /* PCI IDs taken from drivers/net/e100.c */ 2435 case 0x1029: 2436 case 0x1030 ... 0x1034: 2437 case 0x1038 ... 0x103E: 2438 case 0x1050 ... 0x1057: 2439 case 0x1059: 2440 case 0x1064 ... 0x106B: 2441 case 0x1091 ... 0x1095: 2442 case 0x1209: 2443 case 0x1229: 2444 case 0x2449: 2445 case 0x2459: 2446 case 0x245D: 2447 case 0x27DC: 2448 break; 2449 default: 2450 return; 2451 } 2452 2453 /* 2454 * Some firmware hands off the e100 with interrupts enabled, 2455 * which can cause a flood of interrupts if packets are 2456 * received before the driver attaches to the device. So 2457 * disable all e100 interrupts here. The driver will 2458 * re-enable them when it's ready. 2459 */ 2460 pci_read_config_word(dev, PCI_COMMAND, &command); 2461 2462 if (!(command & PCI_COMMAND_MEMORY) || !pci_resource_start(dev, 0)) 2463 return; 2464 2465 /* 2466 * Check that the device is in the D0 power state. If it's not, 2467 * there is no point to look any further. 2468 */ 2469 if (dev->pm_cap) { 2470 pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pmcsr); 2471 if ((pmcsr & PCI_PM_CTRL_STATE_MASK) != PCI_D0) 2472 return; 2473 } 2474 2475 /* Convert from PCI bus to resource space. */ 2476 csr = ioremap(pci_resource_start(dev, 0), 8); 2477 if (!csr) { 2478 pci_warn(dev, "Can't map e100 registers\n"); 2479 return; 2480 } 2481 2482 cmd_hi = readb(csr + 3); 2483 if (cmd_hi == 0) { 2484 pci_warn(dev, "Firmware left e100 interrupts enabled; disabling\n"); 2485 writeb(1, csr + 3); 2486 } 2487 2488 iounmap(csr); 2489 } 2490 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, 2491 PCI_CLASS_NETWORK_ETHERNET, 8, quirk_e100_interrupt); 2492 2493 /* 2494 * The 82575 and 82598 may experience data corruption issues when transitioning 2495 * out of L0S. To prevent this we need to disable L0S on the PCIe link. 2496 */ 2497 static void quirk_disable_aspm_l0s(struct pci_dev *dev) 2498 { 2499 pci_info(dev, "Disabling L0s\n"); 2500 pci_disable_link_state(dev, PCIE_LINK_STATE_L0S); 2501 } 2502 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10a7, quirk_disable_aspm_l0s); 2503 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10a9, quirk_disable_aspm_l0s); 2504 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10b6, quirk_disable_aspm_l0s); 2505 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c6, quirk_disable_aspm_l0s); 2506 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c7, quirk_disable_aspm_l0s); 2507 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c8, quirk_disable_aspm_l0s); 2508 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10d6, quirk_disable_aspm_l0s); 2509 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10db, quirk_disable_aspm_l0s); 2510 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10dd, quirk_disable_aspm_l0s); 2511 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10e1, quirk_disable_aspm_l0s); 2512 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10ec, quirk_disable_aspm_l0s); 2513 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f1, quirk_disable_aspm_l0s); 2514 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f4, quirk_disable_aspm_l0s); 2515 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1508, quirk_disable_aspm_l0s); 2516 2517 static void quirk_disable_aspm_l0s_l1(struct pci_dev *dev) 2518 { 2519 pci_info(dev, "Disabling ASPM L0s/L1\n"); 2520 pci_disable_link_state(dev, PCIE_LINK_STATE_L0S | PCIE_LINK_STATE_L1); 2521 } 2522 2523 /* 2524 * ASM1083/1085 PCIe-PCI bridge devices cause AER timeout errors on the 2525 * upstream PCIe root port when ASPM is enabled. At least L0s mode is affected; 2526 * disable both L0s and L1 for now to be safe. 2527 */ 2528 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ASMEDIA, 0x1080, quirk_disable_aspm_l0s_l1); 2529 2530 /* 2531 * Some Pericom PCIe-to-PCI bridges in reverse mode need the PCIe Retrain 2532 * Link bit cleared after starting the link retrain process to allow this 2533 * process to finish. 2534 * 2535 * Affected devices: PI7C9X110, PI7C9X111SL, PI7C9X130. See also the 2536 * Pericom Errata Sheet PI7C9X111SLB_errata_rev1.2_102711.pdf. 2537 */ 2538 static void quirk_enable_clear_retrain_link(struct pci_dev *dev) 2539 { 2540 dev->clear_retrain_link = 1; 2541 pci_info(dev, "Enable PCIe Retrain Link quirk\n"); 2542 } 2543 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PERICOM, 0xe110, quirk_enable_clear_retrain_link); 2544 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PERICOM, 0xe111, quirk_enable_clear_retrain_link); 2545 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PERICOM, 0xe130, quirk_enable_clear_retrain_link); 2546 2547 static void fixup_rev1_53c810(struct pci_dev *dev) 2548 { 2549 u32 class = dev->class; 2550 2551 /* 2552 * rev 1 ncr53c810 chips don't set the class at all which means 2553 * they don't get their resources remapped. Fix that here. 2554 */ 2555 if (class) 2556 return; 2557 2558 dev->class = PCI_CLASS_STORAGE_SCSI << 8; 2559 pci_info(dev, "NCR 53c810 rev 1 PCI class overridden (%#08x -> %#08x)\n", 2560 class, dev->class); 2561 } 2562 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810); 2563 2564 /* Enable 1k I/O space granularity on the Intel P64H2 */ 2565 static void quirk_p64h2_1k_io(struct pci_dev *dev) 2566 { 2567 u16 en1k; 2568 2569 pci_read_config_word(dev, 0x40, &en1k); 2570 2571 if (en1k & 0x200) { 2572 pci_info(dev, "Enable I/O Space to 1KB granularity\n"); 2573 dev->io_window_1k = 1; 2574 } 2575 } 2576 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x1460, quirk_p64h2_1k_io); 2577 2578 /* 2579 * Under some circumstances, AER is not linked with extended capabilities. 2580 * Force it to be linked by setting the corresponding control bit in the 2581 * config space. 2582 */ 2583 static void quirk_nvidia_ck804_pcie_aer_ext_cap(struct pci_dev *dev) 2584 { 2585 uint8_t b; 2586 2587 if (pci_read_config_byte(dev, 0xf41, &b) == 0) { 2588 if (!(b & 0x20)) { 2589 pci_write_config_byte(dev, 0xf41, b | 0x20); 2590 pci_info(dev, "Linking AER extended capability\n"); 2591 } 2592 } 2593 } 2594 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE, 2595 quirk_nvidia_ck804_pcie_aer_ext_cap); 2596 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE, 2597 quirk_nvidia_ck804_pcie_aer_ext_cap); 2598 2599 static void quirk_via_cx700_pci_parking_caching(struct pci_dev *dev) 2600 { 2601 /* 2602 * Disable PCI Bus Parking and PCI Master read caching on CX700 2603 * which causes unspecified timing errors with a VT6212L on the PCI 2604 * bus leading to USB2.0 packet loss. 2605 * 2606 * This quirk is only enabled if a second (on the external PCI bus) 2607 * VT6212L is found -- the CX700 core itself also contains a USB 2608 * host controller with the same PCI ID as the VT6212L. 2609 */ 2610 2611 /* Count VT6212L instances */ 2612 struct pci_dev *p = pci_get_device(PCI_VENDOR_ID_VIA, 2613 PCI_DEVICE_ID_VIA_8235_USB_2, NULL); 2614 uint8_t b; 2615 2616 /* 2617 * p should contain the first (internal) VT6212L -- see if we have 2618 * an external one by searching again. 2619 */ 2620 p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235_USB_2, p); 2621 if (!p) 2622 return; 2623 pci_dev_put(p); 2624 2625 if (pci_read_config_byte(dev, 0x76, &b) == 0) { 2626 if (b & 0x40) { 2627 /* Turn off PCI Bus Parking */ 2628 pci_write_config_byte(dev, 0x76, b ^ 0x40); 2629 2630 pci_info(dev, "Disabling VIA CX700 PCI parking\n"); 2631 } 2632 } 2633 2634 if (pci_read_config_byte(dev, 0x72, &b) == 0) { 2635 if (b != 0) { 2636 /* Turn off PCI Master read caching */ 2637 pci_write_config_byte(dev, 0x72, 0x0); 2638 2639 /* Set PCI Master Bus time-out to "1x16 PCLK" */ 2640 pci_write_config_byte(dev, 0x75, 0x1); 2641 2642 /* Disable "Read FIFO Timer" */ 2643 pci_write_config_byte(dev, 0x77, 0x0); 2644 2645 pci_info(dev, "Disabling VIA CX700 PCI caching\n"); 2646 } 2647 } 2648 } 2649 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0x324e, quirk_via_cx700_pci_parking_caching); 2650 2651 static void quirk_brcm_5719_limit_mrrs(struct pci_dev *dev) 2652 { 2653 u32 rev; 2654 2655 pci_read_config_dword(dev, 0xf4, &rev); 2656 2657 /* Only CAP the MRRS if the device is a 5719 A0 */ 2658 if (rev == 0x05719000) { 2659 int readrq = pcie_get_readrq(dev); 2660 if (readrq > 2048) 2661 pcie_set_readrq(dev, 2048); 2662 } 2663 } 2664 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_BROADCOM, 2665 PCI_DEVICE_ID_TIGON3_5719, 2666 quirk_brcm_5719_limit_mrrs); 2667 2668 /* 2669 * Originally in EDAC sources for i82875P: Intel tells BIOS developers to 2670 * hide device 6 which configures the overflow device access containing the 2671 * DRBs - this is where we expose device 6. 2672 * http://www.x86-secret.com/articles/tweak/pat/patsecrets-2.htm 2673 */ 2674 static void quirk_unhide_mch_dev6(struct pci_dev *dev) 2675 { 2676 u8 reg; 2677 2678 if (pci_read_config_byte(dev, 0xF4, ®) == 0 && !(reg & 0x02)) { 2679 pci_info(dev, "Enabling MCH 'Overflow' Device\n"); 2680 pci_write_config_byte(dev, 0xF4, reg | 0x02); 2681 } 2682 } 2683 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB, 2684 quirk_unhide_mch_dev6); 2685 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82875_HB, 2686 quirk_unhide_mch_dev6); 2687 2688 #ifdef CONFIG_PCI_MSI 2689 /* 2690 * Some chipsets do not support MSI. We cannot easily rely on setting 2691 * PCI_BUS_FLAGS_NO_MSI in its bus flags because there are actually some 2692 * other buses controlled by the chipset even if Linux is not aware of it. 2693 * Instead of setting the flag on all buses in the machine, simply disable 2694 * MSI globally. 2695 */ 2696 static void quirk_disable_all_msi(struct pci_dev *dev) 2697 { 2698 pci_no_msi(); 2699 pci_warn(dev, "MSI quirk detected; MSI disabled\n"); 2700 } 2701 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_GCNB_LE, quirk_disable_all_msi); 2702 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS400_200, quirk_disable_all_msi); 2703 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS480, quirk_disable_all_msi); 2704 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3336, quirk_disable_all_msi); 2705 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3351, quirk_disable_all_msi); 2706 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3364, quirk_disable_all_msi); 2707 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8380_0, quirk_disable_all_msi); 2708 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, 0x0761, quirk_disable_all_msi); 2709 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SAMSUNG, 0xa5e3, quirk_disable_all_msi); 2710 2711 /* Disable MSI on chipsets that are known to not support it */ 2712 static void quirk_disable_msi(struct pci_dev *dev) 2713 { 2714 if (dev->subordinate) { 2715 pci_warn(dev, "MSI quirk detected; subordinate MSI disabled\n"); 2716 dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI; 2717 } 2718 } 2719 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_msi); 2720 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0xa238, quirk_disable_msi); 2721 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x5a3f, quirk_disable_msi); 2722 2723 /* 2724 * The APC bridge device in AMD 780 family northbridges has some random 2725 * OEM subsystem ID in its vendor ID register (erratum 18), so instead 2726 * we use the possible vendor/device IDs of the host bridge for the 2727 * declared quirk, and search for the APC bridge by slot number. 2728 */ 2729 static void quirk_amd_780_apc_msi(struct pci_dev *host_bridge) 2730 { 2731 struct pci_dev *apc_bridge; 2732 2733 apc_bridge = pci_get_slot(host_bridge->bus, PCI_DEVFN(1, 0)); 2734 if (apc_bridge) { 2735 if (apc_bridge->device == 0x9602) 2736 quirk_disable_msi(apc_bridge); 2737 pci_dev_put(apc_bridge); 2738 } 2739 } 2740 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x9600, quirk_amd_780_apc_msi); 2741 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x9601, quirk_amd_780_apc_msi); 2742 2743 /* 2744 * Go through the list of HyperTransport capabilities and return 1 if a HT 2745 * MSI capability is found and enabled. 2746 */ 2747 static int msi_ht_cap_enabled(struct pci_dev *dev) 2748 { 2749 int pos, ttl = PCI_FIND_CAP_TTL; 2750 2751 pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); 2752 while (pos && ttl--) { 2753 u8 flags; 2754 2755 if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, 2756 &flags) == 0) { 2757 pci_info(dev, "Found %s HT MSI Mapping\n", 2758 flags & HT_MSI_FLAGS_ENABLE ? 2759 "enabled" : "disabled"); 2760 return (flags & HT_MSI_FLAGS_ENABLE) != 0; 2761 } 2762 2763 pos = pci_find_next_ht_capability(dev, pos, 2764 HT_CAPTYPE_MSI_MAPPING); 2765 } 2766 return 0; 2767 } 2768 2769 /* Check the HyperTransport MSI mapping to know whether MSI is enabled or not */ 2770 static void quirk_msi_ht_cap(struct pci_dev *dev) 2771 { 2772 if (!msi_ht_cap_enabled(dev)) 2773 quirk_disable_msi(dev); 2774 } 2775 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT2000_PCIE, 2776 quirk_msi_ht_cap); 2777 2778 /* 2779 * The nVidia CK804 chipset may have 2 HT MSI mappings. MSI is supported 2780 * if the MSI capability is set in any of these mappings. 2781 */ 2782 static void quirk_nvidia_ck804_msi_ht_cap(struct pci_dev *dev) 2783 { 2784 struct pci_dev *pdev; 2785 2786 /* 2787 * Check HT MSI cap on this chipset and the root one. A single one 2788 * having MSI is enough to be sure that MSI is supported. 2789 */ 2790 pdev = pci_get_slot(dev->bus, 0); 2791 if (!pdev) 2792 return; 2793 if (!msi_ht_cap_enabled(pdev)) 2794 quirk_msi_ht_cap(dev); 2795 pci_dev_put(pdev); 2796 } 2797 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE, 2798 quirk_nvidia_ck804_msi_ht_cap); 2799 2800 /* Force enable MSI mapping capability on HT bridges */ 2801 static void ht_enable_msi_mapping(struct pci_dev *dev) 2802 { 2803 int pos, ttl = PCI_FIND_CAP_TTL; 2804 2805 pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); 2806 while (pos && ttl--) { 2807 u8 flags; 2808 2809 if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, 2810 &flags) == 0) { 2811 pci_info(dev, "Enabling HT MSI Mapping\n"); 2812 2813 pci_write_config_byte(dev, pos + HT_MSI_FLAGS, 2814 flags | HT_MSI_FLAGS_ENABLE); 2815 } 2816 pos = pci_find_next_ht_capability(dev, pos, 2817 HT_CAPTYPE_MSI_MAPPING); 2818 } 2819 } 2820 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SERVERWORKS, 2821 PCI_DEVICE_ID_SERVERWORKS_HT1000_PXB, 2822 ht_enable_msi_mapping); 2823 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, 2824 ht_enable_msi_mapping); 2825 2826 /* 2827 * The P5N32-SLI motherboards from Asus have a problem with MSI 2828 * for the MCP55 NIC. It is not yet determined whether the MSI problem 2829 * also affects other devices. As for now, turn off MSI for this device. 2830 */ 2831 static void nvenet_msi_disable(struct pci_dev *dev) 2832 { 2833 const char *board_name = dmi_get_system_info(DMI_BOARD_NAME); 2834 2835 if (board_name && 2836 (strstr(board_name, "P5N32-SLI PREMIUM") || 2837 strstr(board_name, "P5N32-E SLI"))) { 2838 pci_info(dev, "Disabling MSI for MCP55 NIC on P5N32-SLI\n"); 2839 dev->no_msi = 1; 2840 } 2841 } 2842 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA, 2843 PCI_DEVICE_ID_NVIDIA_NVENET_15, 2844 nvenet_msi_disable); 2845 2846 /* 2847 * PCIe spec r6.0 sec 6.1.4.3 says that if MSI/MSI-X is enabled, the device 2848 * can't use INTx interrupts. Tegra's PCIe Root Ports don't generate MSI 2849 * interrupts for PME and AER events; instead only INTx interrupts are 2850 * generated. Though Tegra's PCIe Root Ports can generate MSI interrupts 2851 * for other events, since PCIe specification doesn't support using a mix of 2852 * INTx and MSI/MSI-X, it is required to disable MSI interrupts to avoid port 2853 * service drivers registering their respective ISRs for MSIs. 2854 */ 2855 static void pci_quirk_nvidia_tegra_disable_rp_msi(struct pci_dev *dev) 2856 { 2857 dev->no_msi = 1; 2858 } 2859 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x1ad0, 2860 PCI_CLASS_BRIDGE_PCI, 8, 2861 pci_quirk_nvidia_tegra_disable_rp_msi); 2862 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x1ad1, 2863 PCI_CLASS_BRIDGE_PCI, 8, 2864 pci_quirk_nvidia_tegra_disable_rp_msi); 2865 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x1ad2, 2866 PCI_CLASS_BRIDGE_PCI, 8, 2867 pci_quirk_nvidia_tegra_disable_rp_msi); 2868 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0bf0, 2869 PCI_CLASS_BRIDGE_PCI, 8, 2870 pci_quirk_nvidia_tegra_disable_rp_msi); 2871 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0bf1, 2872 PCI_CLASS_BRIDGE_PCI, 8, 2873 pci_quirk_nvidia_tegra_disable_rp_msi); 2874 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e1c, 2875 PCI_CLASS_BRIDGE_PCI, 8, 2876 pci_quirk_nvidia_tegra_disable_rp_msi); 2877 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e1d, 2878 PCI_CLASS_BRIDGE_PCI, 8, 2879 pci_quirk_nvidia_tegra_disable_rp_msi); 2880 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e12, 2881 PCI_CLASS_BRIDGE_PCI, 8, 2882 pci_quirk_nvidia_tegra_disable_rp_msi); 2883 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e13, 2884 PCI_CLASS_BRIDGE_PCI, 8, 2885 pci_quirk_nvidia_tegra_disable_rp_msi); 2886 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0fae, 2887 PCI_CLASS_BRIDGE_PCI, 8, 2888 pci_quirk_nvidia_tegra_disable_rp_msi); 2889 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0faf, 2890 PCI_CLASS_BRIDGE_PCI, 8, 2891 pci_quirk_nvidia_tegra_disable_rp_msi); 2892 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x10e5, 2893 PCI_CLASS_BRIDGE_PCI, 8, 2894 pci_quirk_nvidia_tegra_disable_rp_msi); 2895 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x10e6, 2896 PCI_CLASS_BRIDGE_PCI, 8, 2897 pci_quirk_nvidia_tegra_disable_rp_msi); 2898 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x229a, 2899 PCI_CLASS_BRIDGE_PCI, 8, 2900 pci_quirk_nvidia_tegra_disable_rp_msi); 2901 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x229c, 2902 PCI_CLASS_BRIDGE_PCI, 8, 2903 pci_quirk_nvidia_tegra_disable_rp_msi); 2904 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x229e, 2905 PCI_CLASS_BRIDGE_PCI, 8, 2906 pci_quirk_nvidia_tegra_disable_rp_msi); 2907 2908 /* 2909 * Some versions of the MCP55 bridge from Nvidia have a legacy IRQ routing 2910 * config register. This register controls the routing of legacy 2911 * interrupts from devices that route through the MCP55. If this register 2912 * is misprogrammed, interrupts are only sent to the BSP, unlike 2913 * conventional systems where the IRQ is broadcast to all online CPUs. Not 2914 * having this register set properly prevents kdump from booting up 2915 * properly, so let's make sure that we have it set correctly. 2916 * Note that this is an undocumented register. 2917 */ 2918 static void nvbridge_check_legacy_irq_routing(struct pci_dev *dev) 2919 { 2920 u32 cfg; 2921 2922 if (!pci_find_capability(dev, PCI_CAP_ID_HT)) 2923 return; 2924 2925 pci_read_config_dword(dev, 0x74, &cfg); 2926 2927 if (cfg & ((1 << 2) | (1 << 15))) { 2928 pr_info("Rewriting IRQ routing register on MCP55\n"); 2929 cfg &= ~((1 << 2) | (1 << 15)); 2930 pci_write_config_dword(dev, 0x74, cfg); 2931 } 2932 } 2933 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA, 2934 PCI_DEVICE_ID_NVIDIA_MCP55_BRIDGE_V0, 2935 nvbridge_check_legacy_irq_routing); 2936 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA, 2937 PCI_DEVICE_ID_NVIDIA_MCP55_BRIDGE_V4, 2938 nvbridge_check_legacy_irq_routing); 2939 2940 static int ht_check_msi_mapping(struct pci_dev *dev) 2941 { 2942 int pos, ttl = PCI_FIND_CAP_TTL; 2943 int found = 0; 2944 2945 /* Check if there is HT MSI cap or enabled on this device */ 2946 pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); 2947 while (pos && ttl--) { 2948 u8 flags; 2949 2950 if (found < 1) 2951 found = 1; 2952 if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, 2953 &flags) == 0) { 2954 if (flags & HT_MSI_FLAGS_ENABLE) { 2955 if (found < 2) { 2956 found = 2; 2957 break; 2958 } 2959 } 2960 } 2961 pos = pci_find_next_ht_capability(dev, pos, 2962 HT_CAPTYPE_MSI_MAPPING); 2963 } 2964 2965 return found; 2966 } 2967 2968 static int host_bridge_with_leaf(struct pci_dev *host_bridge) 2969 { 2970 struct pci_dev *dev; 2971 int pos; 2972 int i, dev_no; 2973 int found = 0; 2974 2975 dev_no = host_bridge->devfn >> 3; 2976 for (i = dev_no + 1; i < 0x20; i++) { 2977 dev = pci_get_slot(host_bridge->bus, PCI_DEVFN(i, 0)); 2978 if (!dev) 2979 continue; 2980 2981 /* found next host bridge? */ 2982 pos = pci_find_ht_capability(dev, HT_CAPTYPE_SLAVE); 2983 if (pos != 0) { 2984 pci_dev_put(dev); 2985 break; 2986 } 2987 2988 if (ht_check_msi_mapping(dev)) { 2989 found = 1; 2990 pci_dev_put(dev); 2991 break; 2992 } 2993 pci_dev_put(dev); 2994 } 2995 2996 return found; 2997 } 2998 2999 #define PCI_HT_CAP_SLAVE_CTRL0 4 /* link control */ 3000 #define PCI_HT_CAP_SLAVE_CTRL1 8 /* link control to */ 3001 3002 static int is_end_of_ht_chain(struct pci_dev *dev) 3003 { 3004 int pos, ctrl_off; 3005 int end = 0; 3006 u16 flags, ctrl; 3007 3008 pos = pci_find_ht_capability(dev, HT_CAPTYPE_SLAVE); 3009 3010 if (!pos) 3011 goto out; 3012 3013 pci_read_config_word(dev, pos + PCI_CAP_FLAGS, &flags); 3014 3015 ctrl_off = ((flags >> 10) & 1) ? 3016 PCI_HT_CAP_SLAVE_CTRL0 : PCI_HT_CAP_SLAVE_CTRL1; 3017 pci_read_config_word(dev, pos + ctrl_off, &ctrl); 3018 3019 if (ctrl & (1 << 6)) 3020 end = 1; 3021 3022 out: 3023 return end; 3024 } 3025 3026 static void nv_ht_enable_msi_mapping(struct pci_dev *dev) 3027 { 3028 struct pci_dev *host_bridge; 3029 int pos; 3030 int i, dev_no; 3031 int found = 0; 3032 3033 dev_no = dev->devfn >> 3; 3034 for (i = dev_no; i >= 0; i--) { 3035 host_bridge = pci_get_slot(dev->bus, PCI_DEVFN(i, 0)); 3036 if (!host_bridge) 3037 continue; 3038 3039 pos = pci_find_ht_capability(host_bridge, HT_CAPTYPE_SLAVE); 3040 if (pos != 0) { 3041 found = 1; 3042 break; 3043 } 3044 pci_dev_put(host_bridge); 3045 } 3046 3047 if (!found) 3048 return; 3049 3050 /* don't enable end_device/host_bridge with leaf directly here */ 3051 if (host_bridge == dev && is_end_of_ht_chain(host_bridge) && 3052 host_bridge_with_leaf(host_bridge)) 3053 goto out; 3054 3055 /* root did that ! */ 3056 if (msi_ht_cap_enabled(host_bridge)) 3057 goto out; 3058 3059 ht_enable_msi_mapping(dev); 3060 3061 out: 3062 pci_dev_put(host_bridge); 3063 } 3064 3065 static void ht_disable_msi_mapping(struct pci_dev *dev) 3066 { 3067 int pos, ttl = PCI_FIND_CAP_TTL; 3068 3069 pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); 3070 while (pos && ttl--) { 3071 u8 flags; 3072 3073 if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, 3074 &flags) == 0) { 3075 pci_info(dev, "Disabling HT MSI Mapping\n"); 3076 3077 pci_write_config_byte(dev, pos + HT_MSI_FLAGS, 3078 flags & ~HT_MSI_FLAGS_ENABLE); 3079 } 3080 pos = pci_find_next_ht_capability(dev, pos, 3081 HT_CAPTYPE_MSI_MAPPING); 3082 } 3083 } 3084 3085 static void __nv_msi_ht_cap_quirk(struct pci_dev *dev, int all) 3086 { 3087 struct pci_dev *host_bridge; 3088 int pos; 3089 int found; 3090 3091 if (!pci_msi_enabled()) 3092 return; 3093 3094 /* check if there is HT MSI cap or enabled on this device */ 3095 found = ht_check_msi_mapping(dev); 3096 3097 /* no HT MSI CAP */ 3098 if (found == 0) 3099 return; 3100 3101 /* 3102 * HT MSI mapping should be disabled on devices that are below 3103 * a non-HyperTransport host bridge. Locate the host bridge. 3104 */ 3105 host_bridge = pci_get_domain_bus_and_slot(pci_domain_nr(dev->bus), 0, 3106 PCI_DEVFN(0, 0)); 3107 if (host_bridge == NULL) { 3108 pci_warn(dev, "nv_msi_ht_cap_quirk didn't locate host bridge\n"); 3109 return; 3110 } 3111 3112 pos = pci_find_ht_capability(host_bridge, HT_CAPTYPE_SLAVE); 3113 if (pos != 0) { 3114 /* Host bridge is to HT */ 3115 if (found == 1) { 3116 /* it is not enabled, try to enable it */ 3117 if (all) 3118 ht_enable_msi_mapping(dev); 3119 else 3120 nv_ht_enable_msi_mapping(dev); 3121 } 3122 goto out; 3123 } 3124 3125 /* HT MSI is not enabled */ 3126 if (found == 1) 3127 goto out; 3128 3129 /* Host bridge is not to HT, disable HT MSI mapping on this device */ 3130 ht_disable_msi_mapping(dev); 3131 3132 out: 3133 pci_dev_put(host_bridge); 3134 } 3135 3136 static void nv_msi_ht_cap_quirk_all(struct pci_dev *dev) 3137 { 3138 return __nv_msi_ht_cap_quirk(dev, 1); 3139 } 3140 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all); 3141 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all); 3142 3143 static void nv_msi_ht_cap_quirk_leaf(struct pci_dev *dev) 3144 { 3145 return __nv_msi_ht_cap_quirk(dev, 0); 3146 } 3147 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk_leaf); 3148 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk_leaf); 3149 3150 static void quirk_msi_intx_disable_bug(struct pci_dev *dev) 3151 { 3152 dev->dev_flags |= PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG; 3153 } 3154 3155 static void quirk_msi_intx_disable_ati_bug(struct pci_dev *dev) 3156 { 3157 struct pci_dev *p; 3158 3159 /* 3160 * SB700 MSI issue will be fixed at HW level from revision A21; 3161 * we need check PCI REVISION ID of SMBus controller to get SB700 3162 * revision. 3163 */ 3164 p = pci_get_device(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SBX00_SMBUS, 3165 NULL); 3166 if (!p) 3167 return; 3168 3169 if ((p->revision < 0x3B) && (p->revision >= 0x30)) 3170 dev->dev_flags |= PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG; 3171 pci_dev_put(p); 3172 } 3173 3174 static void quirk_msi_intx_disable_qca_bug(struct pci_dev *dev) 3175 { 3176 /* AR816X/AR817X/E210X MSI is fixed at HW level from revision 0x18 */ 3177 if (dev->revision < 0x18) { 3178 pci_info(dev, "set MSI_INTX_DISABLE_BUG flag\n"); 3179 dev->dev_flags |= PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG; 3180 } 3181 } 3182 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 3183 PCI_DEVICE_ID_TIGON3_5780, 3184 quirk_msi_intx_disable_bug); 3185 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 3186 PCI_DEVICE_ID_TIGON3_5780S, 3187 quirk_msi_intx_disable_bug); 3188 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 3189 PCI_DEVICE_ID_TIGON3_5714, 3190 quirk_msi_intx_disable_bug); 3191 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 3192 PCI_DEVICE_ID_TIGON3_5714S, 3193 quirk_msi_intx_disable_bug); 3194 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 3195 PCI_DEVICE_ID_TIGON3_5715, 3196 quirk_msi_intx_disable_bug); 3197 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, 3198 PCI_DEVICE_ID_TIGON3_5715S, 3199 quirk_msi_intx_disable_bug); 3200 3201 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4390, 3202 quirk_msi_intx_disable_ati_bug); 3203 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4391, 3204 quirk_msi_intx_disable_ati_bug); 3205 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4392, 3206 quirk_msi_intx_disable_ati_bug); 3207 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4393, 3208 quirk_msi_intx_disable_ati_bug); 3209 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4394, 3210 quirk_msi_intx_disable_ati_bug); 3211 3212 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4373, 3213 quirk_msi_intx_disable_bug); 3214 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4374, 3215 quirk_msi_intx_disable_bug); 3216 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4375, 3217 quirk_msi_intx_disable_bug); 3218 3219 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1062, 3220 quirk_msi_intx_disable_bug); 3221 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1063, 3222 quirk_msi_intx_disable_bug); 3223 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x2060, 3224 quirk_msi_intx_disable_bug); 3225 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x2062, 3226 quirk_msi_intx_disable_bug); 3227 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1073, 3228 quirk_msi_intx_disable_bug); 3229 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1083, 3230 quirk_msi_intx_disable_bug); 3231 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1090, 3232 quirk_msi_intx_disable_qca_bug); 3233 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x1091, 3234 quirk_msi_intx_disable_qca_bug); 3235 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x10a0, 3236 quirk_msi_intx_disable_qca_bug); 3237 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x10a1, 3238 quirk_msi_intx_disable_qca_bug); 3239 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0xe091, 3240 quirk_msi_intx_disable_qca_bug); 3241 3242 /* 3243 * Amazon's Annapurna Labs 1c36:0031 Root Ports don't support MSI-X, so it 3244 * should be disabled on platforms where the device (mistakenly) advertises it. 3245 * 3246 * Notice that this quirk also disables MSI (which may work, but hasn't been 3247 * tested), since currently there is no standard way to disable only MSI-X. 3248 * 3249 * The 0031 device id is reused for other non Root Port device types, 3250 * therefore the quirk is registered for the PCI_CLASS_BRIDGE_PCI class. 3251 */ 3252 static void quirk_al_msi_disable(struct pci_dev *dev) 3253 { 3254 dev->no_msi = 1; 3255 pci_warn(dev, "Disabling MSI/MSI-X\n"); 3256 } 3257 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_AMAZON_ANNAPURNA_LABS, 0x0031, 3258 PCI_CLASS_BRIDGE_PCI, 8, quirk_al_msi_disable); 3259 #endif /* CONFIG_PCI_MSI */ 3260 3261 /* 3262 * Allow manual resource allocation for PCI hotplug bridges via 3263 * pci=hpmemsize=nnM and pci=hpiosize=nnM parameters. For some PCI-PCI 3264 * hotplug bridges, like PLX 6254 (former HINT HB6), kernel fails to 3265 * allocate resources when hotplug device is inserted and PCI bus is 3266 * rescanned. 3267 */ 3268 static void quirk_hotplug_bridge(struct pci_dev *dev) 3269 { 3270 dev->is_hotplug_bridge = 1; 3271 } 3272 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_HINT, 0x0020, quirk_hotplug_bridge); 3273 3274 /* 3275 * This is a quirk for the Ricoh MMC controller found as a part of some 3276 * multifunction chips. 3277 * 3278 * This is very similar and based on the ricoh_mmc driver written by 3279 * Philip Langdale. Thank you for these magic sequences. 3280 * 3281 * These chips implement the four main memory card controllers (SD, MMC, 3282 * MS, xD) and one or both of CardBus or FireWire. 3283 * 3284 * It happens that they implement SD and MMC support as separate 3285 * controllers (and PCI functions). The Linux SDHCI driver supports MMC 3286 * cards but the chip detects MMC cards in hardware and directs them to the 3287 * MMC controller - so the SDHCI driver never sees them. 3288 * 3289 * To get around this, we must disable the useless MMC controller. At that 3290 * point, the SDHCI controller will start seeing them. It seems to be the 3291 * case that the relevant PCI registers to deactivate the MMC controller 3292 * live on PCI function 0, which might be the CardBus controller or the 3293 * FireWire controller, depending on the particular chip in question 3294 * 3295 * This has to be done early, because as soon as we disable the MMC controller 3296 * other PCI functions shift up one level, e.g. function #2 becomes function 3297 * #1, and this will confuse the PCI core. 3298 */ 3299 #ifdef CONFIG_MMC_RICOH_MMC 3300 static void ricoh_mmc_fixup_rl5c476(struct pci_dev *dev) 3301 { 3302 u8 write_enable; 3303 u8 write_target; 3304 u8 disable; 3305 3306 /* 3307 * Disable via CardBus interface 3308 * 3309 * This must be done via function #0 3310 */ 3311 if (PCI_FUNC(dev->devfn)) 3312 return; 3313 3314 pci_read_config_byte(dev, 0xB7, &disable); 3315 if (disable & 0x02) 3316 return; 3317 3318 pci_read_config_byte(dev, 0x8E, &write_enable); 3319 pci_write_config_byte(dev, 0x8E, 0xAA); 3320 pci_read_config_byte(dev, 0x8D, &write_target); 3321 pci_write_config_byte(dev, 0x8D, 0xB7); 3322 pci_write_config_byte(dev, 0xB7, disable | 0x02); 3323 pci_write_config_byte(dev, 0x8E, write_enable); 3324 pci_write_config_byte(dev, 0x8D, write_target); 3325 3326 pci_notice(dev, "proprietary Ricoh MMC controller disabled (via CardBus function)\n"); 3327 pci_notice(dev, "MMC cards are now supported by standard SDHCI controller\n"); 3328 } 3329 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, ricoh_mmc_fixup_rl5c476); 3330 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, ricoh_mmc_fixup_rl5c476); 3331 3332 static void ricoh_mmc_fixup_r5c832(struct pci_dev *dev) 3333 { 3334 u8 write_enable; 3335 u8 disable; 3336 3337 /* 3338 * Disable via FireWire interface 3339 * 3340 * This must be done via function #0 3341 */ 3342 if (PCI_FUNC(dev->devfn)) 3343 return; 3344 /* 3345 * RICOH 0xe822 and 0xe823 SD/MMC card readers fail to recognize 3346 * certain types of SD/MMC cards. Lowering the SD base clock 3347 * frequency from 200Mhz to 50Mhz fixes this issue. 3348 * 3349 * 0x150 - SD2.0 mode enable for changing base clock 3350 * frequency to 50Mhz 3351 * 0xe1 - Base clock frequency 3352 * 0x32 - 50Mhz new clock frequency 3353 * 0xf9 - Key register for 0x150 3354 * 0xfc - key register for 0xe1 3355 */ 3356 if (dev->device == PCI_DEVICE_ID_RICOH_R5CE822 || 3357 dev->device == PCI_DEVICE_ID_RICOH_R5CE823) { 3358 pci_write_config_byte(dev, 0xf9, 0xfc); 3359 pci_write_config_byte(dev, 0x150, 0x10); 3360 pci_write_config_byte(dev, 0xf9, 0x00); 3361 pci_write_config_byte(dev, 0xfc, 0x01); 3362 pci_write_config_byte(dev, 0xe1, 0x32); 3363 pci_write_config_byte(dev, 0xfc, 0x00); 3364 3365 pci_notice(dev, "MMC controller base frequency changed to 50Mhz.\n"); 3366 } 3367 3368 pci_read_config_byte(dev, 0xCB, &disable); 3369 3370 if (disable & 0x02) 3371 return; 3372 3373 pci_read_config_byte(dev, 0xCA, &write_enable); 3374 pci_write_config_byte(dev, 0xCA, 0x57); 3375 pci_write_config_byte(dev, 0xCB, disable | 0x02); 3376 pci_write_config_byte(dev, 0xCA, write_enable); 3377 3378 pci_notice(dev, "proprietary Ricoh MMC controller disabled (via FireWire function)\n"); 3379 pci_notice(dev, "MMC cards are now supported by standard SDHCI controller\n"); 3380 3381 } 3382 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832); 3383 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832); 3384 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE822, ricoh_mmc_fixup_r5c832); 3385 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE822, ricoh_mmc_fixup_r5c832); 3386 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE823, ricoh_mmc_fixup_r5c832); 3387 DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE823, ricoh_mmc_fixup_r5c832); 3388 #endif /*CONFIG_MMC_RICOH_MMC*/ 3389 3390 #ifdef CONFIG_DMAR_TABLE 3391 #define VTUNCERRMSK_REG 0x1ac 3392 #define VTD_MSK_SPEC_ERRORS (1 << 31) 3393 /* 3394 * This is a quirk for masking VT-d spec-defined errors to platform error 3395 * handling logic. Without this, platforms using Intel 7500, 5500 chipsets 3396 * (and the derivative chipsets like X58 etc) seem to generate NMI/SMI (based 3397 * on the RAS config settings of the platform) when a VT-d fault happens. 3398 * The resulting SMI caused the system to hang. 3399 * 3400 * VT-d spec-related errors are already handled by the VT-d OS code, so no 3401 * need to report the same error through other channels. 3402 */ 3403 static void vtd_mask_spec_errors(struct pci_dev *dev) 3404 { 3405 u32 word; 3406 3407 pci_read_config_dword(dev, VTUNCERRMSK_REG, &word); 3408 pci_write_config_dword(dev, VTUNCERRMSK_REG, word | VTD_MSK_SPEC_ERRORS); 3409 } 3410 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x342e, vtd_mask_spec_errors); 3411 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x3c28, vtd_mask_spec_errors); 3412 #endif 3413 3414 static void fixup_ti816x_class(struct pci_dev *dev) 3415 { 3416 u32 class = dev->class; 3417 3418 /* TI 816x devices do not have class code set when in PCIe boot mode */ 3419 dev->class = PCI_CLASS_MULTIMEDIA_VIDEO << 8; 3420 pci_info(dev, "PCI class overridden (%#08x -> %#08x)\n", 3421 class, dev->class); 3422 } 3423 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_TI, 0xb800, 3424 PCI_CLASS_NOT_DEFINED, 8, fixup_ti816x_class); 3425 3426 /* 3427 * Some PCIe devices do not work reliably with the claimed maximum 3428 * payload size supported. 3429 */ 3430 static void fixup_mpss_256(struct pci_dev *dev) 3431 { 3432 dev->pcie_mpss = 1; /* 256 bytes */ 3433 } 3434 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SOLARFLARE, 3435 PCI_DEVICE_ID_SOLARFLARE_SFC4000A_0, fixup_mpss_256); 3436 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SOLARFLARE, 3437 PCI_DEVICE_ID_SOLARFLARE_SFC4000A_1, fixup_mpss_256); 3438 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SOLARFLARE, 3439 PCI_DEVICE_ID_SOLARFLARE_SFC4000B, fixup_mpss_256); 3440 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_ASMEDIA, 0x0612, fixup_mpss_256); 3441 3442 /* 3443 * Intel 5000 and 5100 Memory controllers have an erratum with read completion 3444 * coalescing (which is enabled by default on some BIOSes) and MPS of 256B. 3445 * Since there is no way of knowing what the PCIe MPS on each fabric will be 3446 * until all of the devices are discovered and buses walked, read completion 3447 * coalescing must be disabled. Unfortunately, it cannot be re-enabled because 3448 * it is possible to hotplug a device with MPS of 256B. 3449 */ 3450 static void quirk_intel_mc_errata(struct pci_dev *dev) 3451 { 3452 int err; 3453 u16 rcc; 3454 3455 if (pcie_bus_config == PCIE_BUS_TUNE_OFF || 3456 pcie_bus_config == PCIE_BUS_DEFAULT) 3457 return; 3458 3459 /* 3460 * Intel erratum specifies bits to change but does not say what 3461 * they are. Keeping them magical until such time as the registers 3462 * and values can be explained. 3463 */ 3464 err = pci_read_config_word(dev, 0x48, &rcc); 3465 if (err) { 3466 pci_err(dev, "Error attempting to read the read completion coalescing register\n"); 3467 return; 3468 } 3469 3470 if (!(rcc & (1 << 10))) 3471 return; 3472 3473 rcc &= ~(1 << 10); 3474 3475 err = pci_write_config_word(dev, 0x48, rcc); 3476 if (err) { 3477 pci_err(dev, "Error attempting to write the read completion coalescing register\n"); 3478 return; 3479 } 3480 3481 pr_info_once("Read completion coalescing disabled due to hardware erratum relating to 256B MPS\n"); 3482 } 3483 /* Intel 5000 series memory controllers and ports 2-7 */ 3484 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25c0, quirk_intel_mc_errata); 3485 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d0, quirk_intel_mc_errata); 3486 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d4, quirk_intel_mc_errata); 3487 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d8, quirk_intel_mc_errata); 3488 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e2, quirk_intel_mc_errata); 3489 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e3, quirk_intel_mc_errata); 3490 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e4, quirk_intel_mc_errata); 3491 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e5, quirk_intel_mc_errata); 3492 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e6, quirk_intel_mc_errata); 3493 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e7, quirk_intel_mc_errata); 3494 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f7, quirk_intel_mc_errata); 3495 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f8, quirk_intel_mc_errata); 3496 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f9, quirk_intel_mc_errata); 3497 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25fa, quirk_intel_mc_errata); 3498 /* Intel 5100 series memory controllers and ports 2-7 */ 3499 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65c0, quirk_intel_mc_errata); 3500 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e2, quirk_intel_mc_errata); 3501 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e3, quirk_intel_mc_errata); 3502 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e4, quirk_intel_mc_errata); 3503 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e5, quirk_intel_mc_errata); 3504 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e6, quirk_intel_mc_errata); 3505 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e7, quirk_intel_mc_errata); 3506 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f7, quirk_intel_mc_errata); 3507 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f8, quirk_intel_mc_errata); 3508 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f9, quirk_intel_mc_errata); 3509 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65fa, quirk_intel_mc_errata); 3510 3511 /* 3512 * Ivytown NTB BAR sizes are misreported by the hardware due to an erratum. 3513 * To work around this, query the size it should be configured to by the 3514 * device and modify the resource end to correspond to this new size. 3515 */ 3516 static void quirk_intel_ntb(struct pci_dev *dev) 3517 { 3518 int rc; 3519 u8 val; 3520 3521 rc = pci_read_config_byte(dev, 0x00D0, &val); 3522 if (rc) 3523 return; 3524 3525 dev->resource[2].end = dev->resource[2].start + ((u64) 1 << val) - 1; 3526 3527 rc = pci_read_config_byte(dev, 0x00D1, &val); 3528 if (rc) 3529 return; 3530 3531 dev->resource[4].end = dev->resource[4].start + ((u64) 1 << val) - 1; 3532 } 3533 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x0e08, quirk_intel_ntb); 3534 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x0e0d, quirk_intel_ntb); 3535 3536 /* 3537 * Some BIOS implementations leave the Intel GPU interrupts enabled, even 3538 * though no one is handling them (e.g., if the i915 driver is never 3539 * loaded). Additionally the interrupt destination is not set up properly 3540 * and the interrupt ends up -somewhere-. 3541 * 3542 * These spurious interrupts are "sticky" and the kernel disables the 3543 * (shared) interrupt line after 100,000+ generated interrupts. 3544 * 3545 * Fix it by disabling the still enabled interrupts. This resolves crashes 3546 * often seen on monitor unplug. 3547 */ 3548 #define I915_DEIER_REG 0x4400c 3549 static void disable_igfx_irq(struct pci_dev *dev) 3550 { 3551 void __iomem *regs = pci_iomap(dev, 0, 0); 3552 if (regs == NULL) { 3553 pci_warn(dev, "igfx quirk: Can't iomap PCI device\n"); 3554 return; 3555 } 3556 3557 /* Check if any interrupt line is still enabled */ 3558 if (readl(regs + I915_DEIER_REG) != 0) { 3559 pci_warn(dev, "BIOS left Intel GPU interrupts enabled; disabling\n"); 3560 3561 writel(0, regs + I915_DEIER_REG); 3562 } 3563 3564 pci_iounmap(dev, regs); 3565 } 3566 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0042, disable_igfx_irq); 3567 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0046, disable_igfx_irq); 3568 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x004a, disable_igfx_irq); 3569 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0102, disable_igfx_irq); 3570 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0106, disable_igfx_irq); 3571 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x010a, disable_igfx_irq); 3572 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0152, disable_igfx_irq); 3573 3574 /* 3575 * PCI devices which are on Intel chips can skip the 10ms delay 3576 * before entering D3 mode. 3577 */ 3578 static void quirk_remove_d3hot_delay(struct pci_dev *dev) 3579 { 3580 dev->d3hot_delay = 0; 3581 } 3582 /* C600 Series devices do not need 10ms d3hot_delay */ 3583 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0412, quirk_remove_d3hot_delay); 3584 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0c00, quirk_remove_d3hot_delay); 3585 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0c0c, quirk_remove_d3hot_delay); 3586 /* Lynxpoint-H PCH devices do not need 10ms d3hot_delay */ 3587 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c02, quirk_remove_d3hot_delay); 3588 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c18, quirk_remove_d3hot_delay); 3589 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c1c, quirk_remove_d3hot_delay); 3590 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c20, quirk_remove_d3hot_delay); 3591 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c22, quirk_remove_d3hot_delay); 3592 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c26, quirk_remove_d3hot_delay); 3593 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c2d, quirk_remove_d3hot_delay); 3594 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c31, quirk_remove_d3hot_delay); 3595 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c3a, quirk_remove_d3hot_delay); 3596 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c3d, quirk_remove_d3hot_delay); 3597 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x8c4e, quirk_remove_d3hot_delay); 3598 /* Intel Cherrytrail devices do not need 10ms d3hot_delay */ 3599 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2280, quirk_remove_d3hot_delay); 3600 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2298, quirk_remove_d3hot_delay); 3601 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x229c, quirk_remove_d3hot_delay); 3602 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b0, quirk_remove_d3hot_delay); 3603 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b5, quirk_remove_d3hot_delay); 3604 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b7, quirk_remove_d3hot_delay); 3605 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22b8, quirk_remove_d3hot_delay); 3606 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22d8, quirk_remove_d3hot_delay); 3607 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x22dc, quirk_remove_d3hot_delay); 3608 3609 /* 3610 * Some devices may pass our check in pci_intx_mask_supported() if 3611 * PCI_COMMAND_INTX_DISABLE works though they actually do not properly 3612 * support this feature. 3613 */ 3614 static void quirk_broken_intx_masking(struct pci_dev *dev) 3615 { 3616 dev->broken_intx_masking = 1; 3617 } 3618 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CHELSIO, 0x0030, 3619 quirk_broken_intx_masking); 3620 DECLARE_PCI_FIXUP_FINAL(0x1814, 0x0601, /* Ralink RT2800 802.11n PCI */ 3621 quirk_broken_intx_masking); 3622 DECLARE_PCI_FIXUP_FINAL(0x1b7c, 0x0004, /* Ceton InfiniTV4 */ 3623 quirk_broken_intx_masking); 3624 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CREATIVE, PCI_DEVICE_ID_CREATIVE_20K2, 3625 quirk_broken_intx_masking); 3626 3627 /* 3628 * Realtek RTL8169 PCI Gigabit Ethernet Controller (rev 10) 3629 * Subsystem: Realtek RTL8169/8110 Family PCI Gigabit Ethernet NIC 3630 * 3631 * RTL8110SC - Fails under PCI device assignment using DisINTx masking. 3632 */ 3633 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_REALTEK, 0x8169, 3634 quirk_broken_intx_masking); 3635 3636 /* 3637 * Intel i40e (XL710/X710) 10/20/40GbE NICs all have broken INTx masking, 3638 * DisINTx can be set but the interrupt status bit is non-functional. 3639 */ 3640 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1572, quirk_broken_intx_masking); 3641 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1574, quirk_broken_intx_masking); 3642 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1580, quirk_broken_intx_masking); 3643 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1581, quirk_broken_intx_masking); 3644 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1583, quirk_broken_intx_masking); 3645 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1584, quirk_broken_intx_masking); 3646 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1585, quirk_broken_intx_masking); 3647 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1586, quirk_broken_intx_masking); 3648 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1587, quirk_broken_intx_masking); 3649 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1588, quirk_broken_intx_masking); 3650 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1589, quirk_broken_intx_masking); 3651 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x158a, quirk_broken_intx_masking); 3652 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x158b, quirk_broken_intx_masking); 3653 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x37d0, quirk_broken_intx_masking); 3654 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x37d1, quirk_broken_intx_masking); 3655 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x37d2, quirk_broken_intx_masking); 3656 3657 static u16 mellanox_broken_intx_devs[] = { 3658 PCI_DEVICE_ID_MELLANOX_HERMON_SDR, 3659 PCI_DEVICE_ID_MELLANOX_HERMON_DDR, 3660 PCI_DEVICE_ID_MELLANOX_HERMON_QDR, 3661 PCI_DEVICE_ID_MELLANOX_HERMON_DDR_GEN2, 3662 PCI_DEVICE_ID_MELLANOX_HERMON_QDR_GEN2, 3663 PCI_DEVICE_ID_MELLANOX_HERMON_EN, 3664 PCI_DEVICE_ID_MELLANOX_HERMON_EN_GEN2, 3665 PCI_DEVICE_ID_MELLANOX_CONNECTX_EN, 3666 PCI_DEVICE_ID_MELLANOX_CONNECTX_EN_T_GEN2, 3667 PCI_DEVICE_ID_MELLANOX_CONNECTX_EN_GEN2, 3668 PCI_DEVICE_ID_MELLANOX_CONNECTX_EN_5_GEN2, 3669 PCI_DEVICE_ID_MELLANOX_CONNECTX2, 3670 PCI_DEVICE_ID_MELLANOX_CONNECTX3, 3671 PCI_DEVICE_ID_MELLANOX_CONNECTX3_PRO, 3672 }; 3673 3674 #define CONNECTX_4_CURR_MAX_MINOR 99 3675 #define CONNECTX_4_INTX_SUPPORT_MINOR 14 3676 3677 /* 3678 * Check ConnectX-4/LX FW version to see if it supports legacy interrupts. 3679 * If so, don't mark it as broken. 3680 * FW minor > 99 means older FW version format and no INTx masking support. 3681 * FW minor < 14 means new FW version format and no INTx masking support. 3682 */ 3683 static void mellanox_check_broken_intx_masking(struct pci_dev *pdev) 3684 { 3685 __be32 __iomem *fw_ver; 3686 u16 fw_major; 3687 u16 fw_minor; 3688 u16 fw_subminor; 3689 u32 fw_maj_min; 3690 u32 fw_sub_min; 3691 int i; 3692 3693 for (i = 0; i < ARRAY_SIZE(mellanox_broken_intx_devs); i++) { 3694 if (pdev->device == mellanox_broken_intx_devs[i]) { 3695 pdev->broken_intx_masking = 1; 3696 return; 3697 } 3698 } 3699 3700 /* 3701 * Getting here means Connect-IB cards and up. Connect-IB has no INTx 3702 * support so shouldn't be checked further 3703 */ 3704 if (pdev->device == PCI_DEVICE_ID_MELLANOX_CONNECTIB) 3705 return; 3706 3707 if (pdev->device != PCI_DEVICE_ID_MELLANOX_CONNECTX4 && 3708 pdev->device != PCI_DEVICE_ID_MELLANOX_CONNECTX4_LX) 3709 return; 3710 3711 /* For ConnectX-4 and ConnectX-4LX, need to check FW support */ 3712 if (pci_enable_device_mem(pdev)) { 3713 pci_warn(pdev, "Can't enable device memory\n"); 3714 return; 3715 } 3716 3717 fw_ver = ioremap(pci_resource_start(pdev, 0), 4); 3718 if (!fw_ver) { 3719 pci_warn(pdev, "Can't map ConnectX-4 initialization segment\n"); 3720 goto out; 3721 } 3722 3723 /* Reading from resource space should be 32b aligned */ 3724 fw_maj_min = ioread32be(fw_ver); 3725 fw_sub_min = ioread32be(fw_ver + 1); 3726 fw_major = fw_maj_min & 0xffff; 3727 fw_minor = fw_maj_min >> 16; 3728 fw_subminor = fw_sub_min & 0xffff; 3729 if (fw_minor > CONNECTX_4_CURR_MAX_MINOR || 3730 fw_minor < CONNECTX_4_INTX_SUPPORT_MINOR) { 3731 pci_warn(pdev, "ConnectX-4: FW %u.%u.%u doesn't support INTx masking, disabling. Please upgrade FW to %d.14.1100 and up for INTx support\n", 3732 fw_major, fw_minor, fw_subminor, pdev->device == 3733 PCI_DEVICE_ID_MELLANOX_CONNECTX4 ? 12 : 14); 3734 pdev->broken_intx_masking = 1; 3735 } 3736 3737 iounmap(fw_ver); 3738 3739 out: 3740 pci_disable_device(pdev); 3741 } 3742 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_MELLANOX, PCI_ANY_ID, 3743 mellanox_check_broken_intx_masking); 3744 3745 static void quirk_no_bus_reset(struct pci_dev *dev) 3746 { 3747 dev->dev_flags |= PCI_DEV_FLAGS_NO_BUS_RESET; 3748 } 3749 3750 /* 3751 * Some NVIDIA GPU devices do not work with bus reset, SBR needs to be 3752 * prevented for those affected devices. 3753 */ 3754 static void quirk_nvidia_no_bus_reset(struct pci_dev *dev) 3755 { 3756 if ((dev->device & 0xffc0) == 0x2340) 3757 quirk_no_bus_reset(dev); 3758 } 3759 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, 3760 quirk_nvidia_no_bus_reset); 3761 3762 /* 3763 * Some Atheros AR9xxx and QCA988x chips do not behave after a bus reset. 3764 * The device will throw a Link Down error on AER-capable systems and 3765 * regardless of AER, config space of the device is never accessible again 3766 * and typically causes the system to hang or reset when access is attempted. 3767 * https://lore.kernel.org/r/20140923210318.498dacbd@dualc.maya.org/ 3768 */ 3769 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x0030, quirk_no_bus_reset); 3770 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x0032, quirk_no_bus_reset); 3771 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x003c, quirk_no_bus_reset); 3772 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x0033, quirk_no_bus_reset); 3773 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x0034, quirk_no_bus_reset); 3774 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATHEROS, 0x003e, quirk_no_bus_reset); 3775 3776 /* 3777 * Root port on some Cavium CN8xxx chips do not successfully complete a bus 3778 * reset when used with certain child devices. After the reset, config 3779 * accesses to the child may fail. 3780 */ 3781 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_CAVIUM, 0xa100, quirk_no_bus_reset); 3782 3783 /* 3784 * Some TI KeyStone C667X devices do not support bus/hot reset. The PCIESS 3785 * automatically disables LTSSM when Secondary Bus Reset is received and 3786 * the device stops working. Prevent bus reset for these devices. With 3787 * this change, the device can be assigned to VMs with VFIO, but it will 3788 * leak state between VMs. Reference 3789 * https://e2e.ti.com/support/processors/f/791/t/954382 3790 */ 3791 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TI, 0xb005, quirk_no_bus_reset); 3792 3793 static void quirk_no_pm_reset(struct pci_dev *dev) 3794 { 3795 /* 3796 * We can't do a bus reset on root bus devices, but an ineffective 3797 * PM reset may be better than nothing. 3798 */ 3799 if (!pci_is_root_bus(dev->bus)) 3800 dev->dev_flags |= PCI_DEV_FLAGS_NO_PM_RESET; 3801 } 3802 3803 /* 3804 * Some AMD/ATI GPUS (HD8570 - Oland) report that a D3hot->D0 transition 3805 * causes a reset (i.e., they advertise NoSoftRst-). This transition seems 3806 * to have no effect on the device: it retains the framebuffer contents and 3807 * monitor sync. Advertising this support makes other layers, like VFIO, 3808 * assume pci_reset_function() is viable for this device. Mark it as 3809 * unavailable to skip it when testing reset methods. 3810 */ 3811 DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_ATI, PCI_ANY_ID, 3812 PCI_CLASS_DISPLAY_VGA, 8, quirk_no_pm_reset); 3813 3814 /* 3815 * Spectrum-{1,2,3,4} devices report that a D3hot->D0 transition causes a reset 3816 * (i.e., they advertise NoSoftRst-). However, this transition does not have 3817 * any effect on the device: It continues to be operational and network ports 3818 * remain up. Advertising this support makes it seem as if a PM reset is viable 3819 * for these devices. Mark it as unavailable to skip it when testing reset 3820 * methods. 3821 */ 3822 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MELLANOX, 0xcb84, quirk_no_pm_reset); 3823 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MELLANOX, 0xcf6c, quirk_no_pm_reset); 3824 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MELLANOX, 0xcf70, quirk_no_pm_reset); 3825 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MELLANOX, 0xcf80, quirk_no_pm_reset); 3826 3827 /* 3828 * Thunderbolt controllers with broken MSI hotplug signaling: 3829 * Entire 1st generation (Light Ridge, Eagle Ridge, Light Peak) and part 3830 * of the 2nd generation (Cactus Ridge 4C up to revision 1, Port Ridge). 3831 */ 3832 static void quirk_thunderbolt_hotplug_msi(struct pci_dev *pdev) 3833 { 3834 if (pdev->is_hotplug_bridge && 3835 (pdev->device != PCI_DEVICE_ID_INTEL_CACTUS_RIDGE_4C || 3836 pdev->revision <= 1)) 3837 pdev->no_msi = 1; 3838 } 3839 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_LIGHT_RIDGE, 3840 quirk_thunderbolt_hotplug_msi); 3841 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EAGLE_RIDGE, 3842 quirk_thunderbolt_hotplug_msi); 3843 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_LIGHT_PEAK, 3844 quirk_thunderbolt_hotplug_msi); 3845 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_CACTUS_RIDGE_4C, 3846 quirk_thunderbolt_hotplug_msi); 3847 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PORT_RIDGE, 3848 quirk_thunderbolt_hotplug_msi); 3849 3850 #ifdef CONFIG_ACPI 3851 /* 3852 * Apple: Shutdown Cactus Ridge Thunderbolt controller. 3853 * 3854 * On Apple hardware the Cactus Ridge Thunderbolt controller needs to be 3855 * shutdown before suspend. Otherwise the native host interface (NHI) will not 3856 * be present after resume if a device was plugged in before suspend. 3857 * 3858 * The Thunderbolt controller consists of a PCIe switch with downstream 3859 * bridges leading to the NHI and to the tunnel PCI bridges. 3860 * 3861 * This quirk cuts power to the whole chip. Therefore we have to apply it 3862 * during suspend_noirq of the upstream bridge. 3863 * 3864 * Power is automagically restored before resume. No action is needed. 3865 */ 3866 static void quirk_apple_poweroff_thunderbolt(struct pci_dev *dev) 3867 { 3868 acpi_handle bridge, SXIO, SXFP, SXLV; 3869 3870 if (!x86_apple_machine) 3871 return; 3872 if (pci_pcie_type(dev) != PCI_EXP_TYPE_UPSTREAM) 3873 return; 3874 3875 /* 3876 * SXIO/SXFP/SXLF turns off power to the Thunderbolt controller. 3877 * We don't know how to turn it back on again, but firmware does, 3878 * so we can only use SXIO/SXFP/SXLF if we're suspending via 3879 * firmware. 3880 */ 3881 if (!pm_suspend_via_firmware()) 3882 return; 3883 3884 bridge = ACPI_HANDLE(&dev->dev); 3885 if (!bridge) 3886 return; 3887 3888 /* 3889 * SXIO and SXLV are present only on machines requiring this quirk. 3890 * Thunderbolt bridges in external devices might have the same 3891 * device ID as those on the host, but they will not have the 3892 * associated ACPI methods. This implicitly checks that we are at 3893 * the right bridge. 3894 */ 3895 if (ACPI_FAILURE(acpi_get_handle(bridge, "DSB0.NHI0.SXIO", &SXIO)) 3896 || ACPI_FAILURE(acpi_get_handle(bridge, "DSB0.NHI0.SXFP", &SXFP)) 3897 || ACPI_FAILURE(acpi_get_handle(bridge, "DSB0.NHI0.SXLV", &SXLV))) 3898 return; 3899 pci_info(dev, "quirk: cutting power to Thunderbolt controller...\n"); 3900 3901 /* magic sequence */ 3902 acpi_execute_simple_method(SXIO, NULL, 1); 3903 acpi_execute_simple_method(SXFP, NULL, 0); 3904 msleep(300); 3905 acpi_execute_simple_method(SXLV, NULL, 0); 3906 acpi_execute_simple_method(SXIO, NULL, 0); 3907 acpi_execute_simple_method(SXLV, NULL, 0); 3908 } 3909 DECLARE_PCI_FIXUP_SUSPEND_LATE(PCI_VENDOR_ID_INTEL, 3910 PCI_DEVICE_ID_INTEL_CACTUS_RIDGE_4C, 3911 quirk_apple_poweroff_thunderbolt); 3912 #endif 3913 3914 /* 3915 * Following are device-specific reset methods which can be used to 3916 * reset a single function if other methods (e.g. FLR, PM D0->D3) are 3917 * not available. 3918 */ 3919 static int reset_intel_82599_sfp_virtfn(struct pci_dev *dev, bool probe) 3920 { 3921 /* 3922 * http://www.intel.com/content/dam/doc/datasheet/82599-10-gbe-controller-datasheet.pdf 3923 * 3924 * The 82599 supports FLR on VFs, but FLR support is reported only 3925 * in the PF DEVCAP (sec 9.3.10.4), not in the VF DEVCAP (sec 9.5). 3926 * Thus we must call pcie_flr() directly without first checking if it is 3927 * supported. 3928 */ 3929 if (!probe) 3930 pcie_flr(dev); 3931 return 0; 3932 } 3933 3934 #define SOUTH_CHICKEN2 0xc2004 3935 #define PCH_PP_STATUS 0xc7200 3936 #define PCH_PP_CONTROL 0xc7204 3937 #define MSG_CTL 0x45010 3938 #define NSDE_PWR_STATE 0xd0100 3939 #define IGD_OPERATION_TIMEOUT 10000 /* set timeout 10 seconds */ 3940 3941 static int reset_ivb_igd(struct pci_dev *dev, bool probe) 3942 { 3943 void __iomem *mmio_base; 3944 unsigned long timeout; 3945 u32 val; 3946 3947 if (probe) 3948 return 0; 3949 3950 mmio_base = pci_iomap(dev, 0, 0); 3951 if (!mmio_base) 3952 return -ENOMEM; 3953 3954 iowrite32(0x00000002, mmio_base + MSG_CTL); 3955 3956 /* 3957 * Clobbering SOUTH_CHICKEN2 register is fine only if the next 3958 * driver loaded sets the right bits. However, this's a reset and 3959 * the bits have been set by i915 previously, so we clobber 3960 * SOUTH_CHICKEN2 register directly here. 3961 */ 3962 iowrite32(0x00000005, mmio_base + SOUTH_CHICKEN2); 3963 3964 val = ioread32(mmio_base + PCH_PP_CONTROL) & 0xfffffffe; 3965 iowrite32(val, mmio_base + PCH_PP_CONTROL); 3966 3967 timeout = jiffies + msecs_to_jiffies(IGD_OPERATION_TIMEOUT); 3968 do { 3969 val = ioread32(mmio_base + PCH_PP_STATUS); 3970 if ((val & 0xb0000000) == 0) 3971 goto reset_complete; 3972 msleep(10); 3973 } while (time_before(jiffies, timeout)); 3974 pci_warn(dev, "timeout during reset\n"); 3975 3976 reset_complete: 3977 iowrite32(0x00000002, mmio_base + NSDE_PWR_STATE); 3978 3979 pci_iounmap(dev, mmio_base); 3980 return 0; 3981 } 3982 3983 /* Device-specific reset method for Chelsio T4-based adapters */ 3984 static int reset_chelsio_generic_dev(struct pci_dev *dev, bool probe) 3985 { 3986 u16 old_command; 3987 u16 msix_flags; 3988 3989 /* 3990 * If this isn't a Chelsio T4-based device, return -ENOTTY indicating 3991 * that we have no device-specific reset method. 3992 */ 3993 if ((dev->device & 0xf000) != 0x4000) 3994 return -ENOTTY; 3995 3996 /* 3997 * If this is the "probe" phase, return 0 indicating that we can 3998 * reset this device. 3999 */ 4000 if (probe) 4001 return 0; 4002 4003 /* 4004 * T4 can wedge if there are DMAs in flight within the chip and Bus 4005 * Master has been disabled. We need to have it on till the Function 4006 * Level Reset completes. (BUS_MASTER is disabled in 4007 * pci_reset_function()). 4008 */ 4009 pci_read_config_word(dev, PCI_COMMAND, &old_command); 4010 pci_write_config_word(dev, PCI_COMMAND, 4011 old_command | PCI_COMMAND_MASTER); 4012 4013 /* 4014 * Perform the actual device function reset, saving and restoring 4015 * configuration information around the reset. 4016 */ 4017 pci_save_state(dev); 4018 4019 /* 4020 * T4 also suffers a Head-Of-Line blocking problem if MSI-X interrupts 4021 * are disabled when an MSI-X interrupt message needs to be delivered. 4022 * So we briefly re-enable MSI-X interrupts for the duration of the 4023 * FLR. The pci_restore_state() below will restore the original 4024 * MSI-X state. 4025 */ 4026 pci_read_config_word(dev, dev->msix_cap+PCI_MSIX_FLAGS, &msix_flags); 4027 if ((msix_flags & PCI_MSIX_FLAGS_ENABLE) == 0) 4028 pci_write_config_word(dev, dev->msix_cap+PCI_MSIX_FLAGS, 4029 msix_flags | 4030 PCI_MSIX_FLAGS_ENABLE | 4031 PCI_MSIX_FLAGS_MASKALL); 4032 4033 pcie_flr(dev); 4034 4035 /* 4036 * Restore the configuration information (BAR values, etc.) including 4037 * the original PCI Configuration Space Command word, and return 4038 * success. 4039 */ 4040 pci_restore_state(dev); 4041 pci_write_config_word(dev, PCI_COMMAND, old_command); 4042 return 0; 4043 } 4044 4045 #define PCI_DEVICE_ID_INTEL_82599_SFP_VF 0x10ed 4046 #define PCI_DEVICE_ID_INTEL_IVB_M_VGA 0x0156 4047 #define PCI_DEVICE_ID_INTEL_IVB_M2_VGA 0x0166 4048 4049 /* 4050 * The Samsung SM961/PM961 controller can sometimes enter a fatal state after 4051 * FLR where config space reads from the device return -1. We seem to be 4052 * able to avoid this condition if we disable the NVMe controller prior to 4053 * FLR. This quirk is generic for any NVMe class device requiring similar 4054 * assistance to quiesce the device prior to FLR. 4055 * 4056 * NVMe specification: https://nvmexpress.org/resources/specifications/ 4057 * Revision 1.0e: 4058 * Chapter 2: Required and optional PCI config registers 4059 * Chapter 3: NVMe control registers 4060 * Chapter 7.3: Reset behavior 4061 */ 4062 static int nvme_disable_and_flr(struct pci_dev *dev, bool probe) 4063 { 4064 void __iomem *bar; 4065 u16 cmd; 4066 u32 cfg; 4067 4068 if (dev->class != PCI_CLASS_STORAGE_EXPRESS || 4069 pcie_reset_flr(dev, PCI_RESET_PROBE) || !pci_resource_start(dev, 0)) 4070 return -ENOTTY; 4071 4072 if (probe) 4073 return 0; 4074 4075 bar = pci_iomap(dev, 0, NVME_REG_CC + sizeof(cfg)); 4076 if (!bar) 4077 return -ENOTTY; 4078 4079 pci_read_config_word(dev, PCI_COMMAND, &cmd); 4080 pci_write_config_word(dev, PCI_COMMAND, cmd | PCI_COMMAND_MEMORY); 4081 4082 cfg = readl(bar + NVME_REG_CC); 4083 4084 /* Disable controller if enabled */ 4085 if (cfg & NVME_CC_ENABLE) { 4086 u32 cap = readl(bar + NVME_REG_CAP); 4087 unsigned long timeout; 4088 4089 /* 4090 * Per nvme_disable_ctrl() skip shutdown notification as it 4091 * could complete commands to the admin queue. We only intend 4092 * to quiesce the device before reset. 4093 */ 4094 cfg &= ~(NVME_CC_SHN_MASK | NVME_CC_ENABLE); 4095 4096 writel(cfg, bar + NVME_REG_CC); 4097 4098 /* 4099 * Some controllers require an additional delay here, see 4100 * NVME_QUIRK_DELAY_BEFORE_CHK_RDY. None of those are yet 4101 * supported by this quirk. 4102 */ 4103 4104 /* Cap register provides max timeout in 500ms increments */ 4105 timeout = ((NVME_CAP_TIMEOUT(cap) + 1) * HZ / 2) + jiffies; 4106 4107 for (;;) { 4108 u32 status = readl(bar + NVME_REG_CSTS); 4109 4110 /* Ready status becomes zero on disable complete */ 4111 if (!(status & NVME_CSTS_RDY)) 4112 break; 4113 4114 msleep(100); 4115 4116 if (time_after(jiffies, timeout)) { 4117 pci_warn(dev, "Timeout waiting for NVMe ready status to clear after disable\n"); 4118 break; 4119 } 4120 } 4121 } 4122 4123 pci_iounmap(dev, bar); 4124 4125 pcie_flr(dev); 4126 4127 return 0; 4128 } 4129 4130 /* 4131 * Some NVMe controllers such as Intel DC P3700 and Solidigm P44 Pro will 4132 * timeout waiting for ready status to change after NVMe enable if the driver 4133 * starts interacting with the device too soon after FLR. A 250ms delay after 4134 * FLR has heuristically proven to produce reliably working results for device 4135 * assignment cases. 4136 */ 4137 static int delay_250ms_after_flr(struct pci_dev *dev, bool probe) 4138 { 4139 if (probe) 4140 return pcie_reset_flr(dev, PCI_RESET_PROBE); 4141 4142 pcie_reset_flr(dev, PCI_RESET_DO_RESET); 4143 4144 msleep(250); 4145 4146 return 0; 4147 } 4148 4149 #define PCI_DEVICE_ID_HINIC_VF 0x375E 4150 #define HINIC_VF_FLR_TYPE 0x1000 4151 #define HINIC_VF_FLR_CAP_BIT (1UL << 30) 4152 #define HINIC_VF_OP 0xE80 4153 #define HINIC_VF_FLR_PROC_BIT (1UL << 18) 4154 #define HINIC_OPERATION_TIMEOUT 15000 /* 15 seconds */ 4155 4156 /* Device-specific reset method for Huawei Intelligent NIC virtual functions */ 4157 static int reset_hinic_vf_dev(struct pci_dev *pdev, bool probe) 4158 { 4159 unsigned long timeout; 4160 void __iomem *bar; 4161 u32 val; 4162 4163 if (probe) 4164 return 0; 4165 4166 bar = pci_iomap(pdev, 0, 0); 4167 if (!bar) 4168 return -ENOTTY; 4169 4170 /* Get and check firmware capabilities */ 4171 val = ioread32be(bar + HINIC_VF_FLR_TYPE); 4172 if (!(val & HINIC_VF_FLR_CAP_BIT)) { 4173 pci_iounmap(pdev, bar); 4174 return -ENOTTY; 4175 } 4176 4177 /* Set HINIC_VF_FLR_PROC_BIT for the start of FLR */ 4178 val = ioread32be(bar + HINIC_VF_OP); 4179 val = val | HINIC_VF_FLR_PROC_BIT; 4180 iowrite32be(val, bar + HINIC_VF_OP); 4181 4182 pcie_flr(pdev); 4183 4184 /* 4185 * The device must recapture its Bus and Device Numbers after FLR 4186 * in order generate Completions. Issue a config write to let the 4187 * device capture this information. 4188 */ 4189 pci_write_config_word(pdev, PCI_VENDOR_ID, 0); 4190 4191 /* Firmware clears HINIC_VF_FLR_PROC_BIT when reset is complete */ 4192 timeout = jiffies + msecs_to_jiffies(HINIC_OPERATION_TIMEOUT); 4193 do { 4194 val = ioread32be(bar + HINIC_VF_OP); 4195 if (!(val & HINIC_VF_FLR_PROC_BIT)) 4196 goto reset_complete; 4197 msleep(20); 4198 } while (time_before(jiffies, timeout)); 4199 4200 val = ioread32be(bar + HINIC_VF_OP); 4201 if (!(val & HINIC_VF_FLR_PROC_BIT)) 4202 goto reset_complete; 4203 4204 pci_warn(pdev, "Reset dev timeout, FLR ack reg: %#010x\n", val); 4205 4206 reset_complete: 4207 pci_iounmap(pdev, bar); 4208 4209 return 0; 4210 } 4211 4212 static const struct pci_dev_reset_methods pci_dev_reset_methods[] = { 4213 { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82599_SFP_VF, 4214 reset_intel_82599_sfp_virtfn }, 4215 { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IVB_M_VGA, 4216 reset_ivb_igd }, 4217 { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IVB_M2_VGA, 4218 reset_ivb_igd }, 4219 { PCI_VENDOR_ID_SAMSUNG, 0xa804, nvme_disable_and_flr }, 4220 { PCI_VENDOR_ID_INTEL, 0x0953, delay_250ms_after_flr }, 4221 { PCI_VENDOR_ID_INTEL, 0x0a54, delay_250ms_after_flr }, 4222 { PCI_VENDOR_ID_SOLIDIGM, 0xf1ac, delay_250ms_after_flr }, 4223 { PCI_VENDOR_ID_CHELSIO, PCI_ANY_ID, 4224 reset_chelsio_generic_dev }, 4225 { PCI_VENDOR_ID_HUAWEI, PCI_DEVICE_ID_HINIC_VF, 4226 reset_hinic_vf_dev }, 4227 { 0 } 4228 }; 4229 4230 /* 4231 * These device-specific reset methods are here rather than in a driver 4232 * because when a host assigns a device to a guest VM, the host may need 4233 * to reset the device but probably doesn't have a driver for it. 4234 */ 4235 int pci_dev_specific_reset(struct pci_dev *dev, bool probe) 4236 { 4237 const struct pci_dev_reset_methods *i; 4238 4239 for (i = pci_dev_reset_methods; i->reset; i++) { 4240 if ((i->vendor == dev->vendor || 4241 i->vendor == (u16)PCI_ANY_ID) && 4242 (i->device == dev->device || 4243 i->device == (u16)PCI_ANY_ID)) 4244 return i->reset(dev, probe); 4245 } 4246 4247 return -ENOTTY; 4248 } 4249 4250 static void quirk_dma_func0_alias(struct pci_dev *dev) 4251 { 4252 if (PCI_FUNC(dev->devfn) != 0) 4253 pci_add_dma_alias(dev, PCI_DEVFN(PCI_SLOT(dev->devfn), 0), 1); 4254 } 4255 4256 /* 4257 * https://bugzilla.redhat.com/show_bug.cgi?id=605888 4258 * 4259 * Some Ricoh devices use function 0 as the PCIe requester ID for DMA. 4260 */ 4261 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_RICOH, 0xe832, quirk_dma_func0_alias); 4262 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_RICOH, 0xe476, quirk_dma_func0_alias); 4263 4264 /* Some Glenfly chips use function 0 as the PCIe Requester ID for DMA */ 4265 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_GLENFLY, 0x3d40, quirk_dma_func0_alias); 4266 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_GLENFLY, 0x3d41, quirk_dma_func0_alias); 4267 4268 static void quirk_dma_func1_alias(struct pci_dev *dev) 4269 { 4270 if (PCI_FUNC(dev->devfn) != 1) 4271 pci_add_dma_alias(dev, PCI_DEVFN(PCI_SLOT(dev->devfn), 1), 1); 4272 } 4273 4274 /* 4275 * Marvell 88SE9123 uses function 1 as the requester ID for DMA. In some 4276 * SKUs function 1 is present and is a legacy IDE controller, in other 4277 * SKUs this function is not present, making this a ghost requester. 4278 * https://bugzilla.kernel.org/show_bug.cgi?id=42679 4279 */ 4280 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9120, 4281 quirk_dma_func1_alias); 4282 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9123, 4283 quirk_dma_func1_alias); 4284 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c136 */ 4285 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9125, 4286 quirk_dma_func1_alias); 4287 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9128, 4288 quirk_dma_func1_alias); 4289 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c14 */ 4290 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9130, 4291 quirk_dma_func1_alias); 4292 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9170, 4293 quirk_dma_func1_alias); 4294 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c47 + c57 */ 4295 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9172, 4296 quirk_dma_func1_alias); 4297 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c59 */ 4298 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x917a, 4299 quirk_dma_func1_alias); 4300 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c78 */ 4301 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9182, 4302 quirk_dma_func1_alias); 4303 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c134 */ 4304 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9183, 4305 quirk_dma_func1_alias); 4306 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c46 */ 4307 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x91a0, 4308 quirk_dma_func1_alias); 4309 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c135 */ 4310 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9215, 4311 quirk_dma_func1_alias); 4312 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c127 */ 4313 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9220, 4314 quirk_dma_func1_alias); 4315 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c49 */ 4316 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9230, 4317 quirk_dma_func1_alias); 4318 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9235, 4319 quirk_dma_func1_alias); 4320 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TTI, 0x0642, 4321 quirk_dma_func1_alias); 4322 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TTI, 0x0645, 4323 quirk_dma_func1_alias); 4324 /* https://bugs.gentoo.org/show_bug.cgi?id=497630 */ 4325 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_JMICRON, 4326 PCI_DEVICE_ID_JMICRON_JMB388_ESD, 4327 quirk_dma_func1_alias); 4328 /* https://bugzilla.kernel.org/show_bug.cgi?id=42679#c117 */ 4329 DECLARE_PCI_FIXUP_HEADER(0x1c28, /* Lite-On */ 4330 0x0122, /* Plextor M6E (Marvell 88SS9183)*/ 4331 quirk_dma_func1_alias); 4332 4333 /* 4334 * Some devices DMA with the wrong devfn, not just the wrong function. 4335 * quirk_fixed_dma_alias() uses this table to create fixed aliases, where 4336 * the alias is "fixed" and independent of the device devfn. 4337 * 4338 * For example, the Adaptec 3405 is a PCIe card with an Intel 80333 I/O 4339 * processor. To software, this appears as a PCIe-to-PCI/X bridge with a 4340 * single device on the secondary bus. In reality, the single exposed 4341 * device at 0e.0 is the Address Translation Unit (ATU) of the controller 4342 * that provides a bridge to the internal bus of the I/O processor. The 4343 * controller supports private devices, which can be hidden from PCI config 4344 * space. In the case of the Adaptec 3405, a private device at 01.0 4345 * appears to be the DMA engine, which therefore needs to become a DMA 4346 * alias for the device. 4347 */ 4348 static const struct pci_device_id fixed_dma_alias_tbl[] = { 4349 { PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x0285, 4350 PCI_VENDOR_ID_ADAPTEC2, 0x02bb), /* Adaptec 3405 */ 4351 .driver_data = PCI_DEVFN(1, 0) }, 4352 { PCI_DEVICE_SUB(PCI_VENDOR_ID_ADAPTEC2, 0x0285, 4353 PCI_VENDOR_ID_ADAPTEC2, 0x02bc), /* Adaptec 3805 */ 4354 .driver_data = PCI_DEVFN(1, 0) }, 4355 { 0 } 4356 }; 4357 4358 static void quirk_fixed_dma_alias(struct pci_dev *dev) 4359 { 4360 const struct pci_device_id *id; 4361 4362 id = pci_match_id(fixed_dma_alias_tbl, dev); 4363 if (id) 4364 pci_add_dma_alias(dev, id->driver_data, 1); 4365 } 4366 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ADAPTEC2, 0x0285, quirk_fixed_dma_alias); 4367 4368 /* 4369 * A few PCIe-to-PCI bridges fail to expose a PCIe capability, resulting in 4370 * using the wrong DMA alias for the device. Some of these devices can be 4371 * used as either forward or reverse bridges, so we need to test whether the 4372 * device is operating in the correct mode. We could probably apply this 4373 * quirk to PCI_ANY_ID, but for now we'll just use known offenders. The test 4374 * is for a non-root, non-PCIe bridge where the upstream device is PCIe and 4375 * is not a PCIe-to-PCI bridge, then @pdev is actually a PCIe-to-PCI bridge. 4376 */ 4377 static void quirk_use_pcie_bridge_dma_alias(struct pci_dev *pdev) 4378 { 4379 if (!pci_is_root_bus(pdev->bus) && 4380 pdev->hdr_type == PCI_HEADER_TYPE_BRIDGE && 4381 !pci_is_pcie(pdev) && pci_is_pcie(pdev->bus->self) && 4382 pci_pcie_type(pdev->bus->self) != PCI_EXP_TYPE_PCI_BRIDGE) 4383 pdev->dev_flags |= PCI_DEV_FLAG_PCIE_BRIDGE_ALIAS; 4384 } 4385 /* ASM1083/1085, https://bugzilla.kernel.org/show_bug.cgi?id=44881#c46 */ 4386 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ASMEDIA, 0x1080, 4387 quirk_use_pcie_bridge_dma_alias); 4388 /* Tundra 8113, https://bugzilla.kernel.org/show_bug.cgi?id=44881#c43 */ 4389 DECLARE_PCI_FIXUP_HEADER(0x10e3, 0x8113, quirk_use_pcie_bridge_dma_alias); 4390 /* ITE 8892, https://bugzilla.kernel.org/show_bug.cgi?id=73551 */ 4391 DECLARE_PCI_FIXUP_HEADER(0x1283, 0x8892, quirk_use_pcie_bridge_dma_alias); 4392 /* ITE 8893 has the same problem as the 8892 */ 4393 DECLARE_PCI_FIXUP_HEADER(0x1283, 0x8893, quirk_use_pcie_bridge_dma_alias); 4394 /* Intel 82801, https://bugzilla.kernel.org/show_bug.cgi?id=44881#c49 */ 4395 DECLARE_PCI_FIXUP_HEADER(0x8086, 0x244e, quirk_use_pcie_bridge_dma_alias); 4396 4397 /* 4398 * MIC x200 NTB forwards PCIe traffic using multiple alien RIDs. They have to 4399 * be added as aliases to the DMA device in order to allow buffer access 4400 * when IOMMU is enabled. Following devfns have to match RIT-LUT table 4401 * programmed in the EEPROM. 4402 */ 4403 static void quirk_mic_x200_dma_alias(struct pci_dev *pdev) 4404 { 4405 pci_add_dma_alias(pdev, PCI_DEVFN(0x10, 0x0), 1); 4406 pci_add_dma_alias(pdev, PCI_DEVFN(0x11, 0x0), 1); 4407 pci_add_dma_alias(pdev, PCI_DEVFN(0x12, 0x3), 1); 4408 } 4409 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2260, quirk_mic_x200_dma_alias); 4410 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2264, quirk_mic_x200_dma_alias); 4411 4412 /* 4413 * Intel Visual Compute Accelerator (VCA) is a family of PCIe add-in devices 4414 * exposing computational units via Non Transparent Bridges (NTB, PEX 87xx). 4415 * 4416 * Similarly to MIC x200, we need to add DMA aliases to allow buffer access 4417 * when IOMMU is enabled. These aliases allow computational unit access to 4418 * host memory. These aliases mark the whole VCA device as one IOMMU 4419 * group. 4420 * 4421 * All possible slot numbers (0x20) are used, since we are unable to tell 4422 * what slot is used on other side. This quirk is intended for both host 4423 * and computational unit sides. The VCA devices have up to five functions 4424 * (four for DMA channels and one additional). 4425 */ 4426 static void quirk_pex_vca_alias(struct pci_dev *pdev) 4427 { 4428 const unsigned int num_pci_slots = 0x20; 4429 unsigned int slot; 4430 4431 for (slot = 0; slot < num_pci_slots; slot++) 4432 pci_add_dma_alias(pdev, PCI_DEVFN(slot, 0x0), 5); 4433 } 4434 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2954, quirk_pex_vca_alias); 4435 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2955, quirk_pex_vca_alias); 4436 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2956, quirk_pex_vca_alias); 4437 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2958, quirk_pex_vca_alias); 4438 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x2959, quirk_pex_vca_alias); 4439 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x295A, quirk_pex_vca_alias); 4440 4441 /* 4442 * The IOMMU and interrupt controller on Broadcom Vulcan/Cavium ThunderX2 are 4443 * associated not at the root bus, but at a bridge below. This quirk avoids 4444 * generating invalid DMA aliases. 4445 */ 4446 static void quirk_bridge_cavm_thrx2_pcie_root(struct pci_dev *pdev) 4447 { 4448 pdev->dev_flags |= PCI_DEV_FLAGS_BRIDGE_XLATE_ROOT; 4449 } 4450 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_BROADCOM, 0x9000, 4451 quirk_bridge_cavm_thrx2_pcie_root); 4452 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_BROADCOM, 0x9084, 4453 quirk_bridge_cavm_thrx2_pcie_root); 4454 4455 /* 4456 * Intersil/Techwell TW686[4589]-based video capture cards have an empty (zero) 4457 * class code. Fix it. 4458 */ 4459 static void quirk_tw686x_class(struct pci_dev *pdev) 4460 { 4461 u32 class = pdev->class; 4462 4463 /* Use "Multimedia controller" class */ 4464 pdev->class = (PCI_CLASS_MULTIMEDIA_OTHER << 8) | 0x01; 4465 pci_info(pdev, "TW686x PCI class overridden (%#08x -> %#08x)\n", 4466 class, pdev->class); 4467 } 4468 DECLARE_PCI_FIXUP_CLASS_EARLY(0x1797, 0x6864, PCI_CLASS_NOT_DEFINED, 8, 4469 quirk_tw686x_class); 4470 DECLARE_PCI_FIXUP_CLASS_EARLY(0x1797, 0x6865, PCI_CLASS_NOT_DEFINED, 8, 4471 quirk_tw686x_class); 4472 DECLARE_PCI_FIXUP_CLASS_EARLY(0x1797, 0x6868, PCI_CLASS_NOT_DEFINED, 8, 4473 quirk_tw686x_class); 4474 DECLARE_PCI_FIXUP_CLASS_EARLY(0x1797, 0x6869, PCI_CLASS_NOT_DEFINED, 8, 4475 quirk_tw686x_class); 4476 4477 /* 4478 * Some devices have problems with Transaction Layer Packets with the Relaxed 4479 * Ordering Attribute set. Such devices should mark themselves and other 4480 * device drivers should check before sending TLPs with RO set. 4481 */ 4482 static void quirk_relaxedordering_disable(struct pci_dev *dev) 4483 { 4484 dev->dev_flags |= PCI_DEV_FLAGS_NO_RELAXED_ORDERING; 4485 pci_info(dev, "Disable Relaxed Ordering Attributes to avoid PCIe Completion erratum\n"); 4486 } 4487 4488 /* 4489 * Intel Xeon processors based on Broadwell/Haswell microarchitecture Root 4490 * Complex have a Flow Control Credit issue which can cause performance 4491 * problems with Upstream Transaction Layer Packets with Relaxed Ordering set. 4492 */ 4493 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f01, PCI_CLASS_NOT_DEFINED, 8, 4494 quirk_relaxedordering_disable); 4495 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f02, PCI_CLASS_NOT_DEFINED, 8, 4496 quirk_relaxedordering_disable); 4497 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f03, PCI_CLASS_NOT_DEFINED, 8, 4498 quirk_relaxedordering_disable); 4499 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f04, PCI_CLASS_NOT_DEFINED, 8, 4500 quirk_relaxedordering_disable); 4501 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f05, PCI_CLASS_NOT_DEFINED, 8, 4502 quirk_relaxedordering_disable); 4503 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f06, PCI_CLASS_NOT_DEFINED, 8, 4504 quirk_relaxedordering_disable); 4505 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f07, PCI_CLASS_NOT_DEFINED, 8, 4506 quirk_relaxedordering_disable); 4507 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f08, PCI_CLASS_NOT_DEFINED, 8, 4508 quirk_relaxedordering_disable); 4509 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f09, PCI_CLASS_NOT_DEFINED, 8, 4510 quirk_relaxedordering_disable); 4511 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f0a, PCI_CLASS_NOT_DEFINED, 8, 4512 quirk_relaxedordering_disable); 4513 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f0b, PCI_CLASS_NOT_DEFINED, 8, 4514 quirk_relaxedordering_disable); 4515 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f0c, PCI_CLASS_NOT_DEFINED, 8, 4516 quirk_relaxedordering_disable); 4517 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f0d, PCI_CLASS_NOT_DEFINED, 8, 4518 quirk_relaxedordering_disable); 4519 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x6f0e, PCI_CLASS_NOT_DEFINED, 8, 4520 quirk_relaxedordering_disable); 4521 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f01, PCI_CLASS_NOT_DEFINED, 8, 4522 quirk_relaxedordering_disable); 4523 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f02, PCI_CLASS_NOT_DEFINED, 8, 4524 quirk_relaxedordering_disable); 4525 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f03, PCI_CLASS_NOT_DEFINED, 8, 4526 quirk_relaxedordering_disable); 4527 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f04, PCI_CLASS_NOT_DEFINED, 8, 4528 quirk_relaxedordering_disable); 4529 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f05, PCI_CLASS_NOT_DEFINED, 8, 4530 quirk_relaxedordering_disable); 4531 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f06, PCI_CLASS_NOT_DEFINED, 8, 4532 quirk_relaxedordering_disable); 4533 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f07, PCI_CLASS_NOT_DEFINED, 8, 4534 quirk_relaxedordering_disable); 4535 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f08, PCI_CLASS_NOT_DEFINED, 8, 4536 quirk_relaxedordering_disable); 4537 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f09, PCI_CLASS_NOT_DEFINED, 8, 4538 quirk_relaxedordering_disable); 4539 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f0a, PCI_CLASS_NOT_DEFINED, 8, 4540 quirk_relaxedordering_disable); 4541 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f0b, PCI_CLASS_NOT_DEFINED, 8, 4542 quirk_relaxedordering_disable); 4543 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f0c, PCI_CLASS_NOT_DEFINED, 8, 4544 quirk_relaxedordering_disable); 4545 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f0d, PCI_CLASS_NOT_DEFINED, 8, 4546 quirk_relaxedordering_disable); 4547 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, 0x2f0e, PCI_CLASS_NOT_DEFINED, 8, 4548 quirk_relaxedordering_disable); 4549 4550 /* 4551 * The AMD ARM A1100 (aka "SEATTLE") SoC has a bug in its PCIe Root Complex 4552 * where Upstream Transaction Layer Packets with the Relaxed Ordering 4553 * Attribute clear are allowed to bypass earlier TLPs with Relaxed Ordering 4554 * set. This is a violation of the PCIe 3.0 Transaction Ordering Rules 4555 * outlined in Section 2.4.1 (PCI Express(r) Base Specification Revision 3.0 4556 * November 10, 2010). As a result, on this platform we can't use Relaxed 4557 * Ordering for Upstream TLPs. 4558 */ 4559 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_AMD, 0x1a00, PCI_CLASS_NOT_DEFINED, 8, 4560 quirk_relaxedordering_disable); 4561 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_AMD, 0x1a01, PCI_CLASS_NOT_DEFINED, 8, 4562 quirk_relaxedordering_disable); 4563 DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_AMD, 0x1a02, PCI_CLASS_NOT_DEFINED, 8, 4564 quirk_relaxedordering_disable); 4565 4566 /* 4567 * Per PCIe r3.0, sec 2.2.9, "Completion headers must supply the same 4568 * values for the Attribute as were supplied in the header of the 4569 * corresponding Request, except as explicitly allowed when IDO is used." 4570 * 4571 * If a non-compliant device generates a completion with a different 4572 * attribute than the request, the receiver may accept it (which itself 4573 * seems non-compliant based on sec 2.3.2), or it may handle it as a 4574 * Malformed TLP or an Unexpected Completion, which will probably lead to a 4575 * device access timeout. 4576 * 4577 * If the non-compliant device generates completions with zero attributes 4578 * (instead of copying the attributes from the request), we can work around 4579 * this by disabling the "Relaxed Ordering" and "No Snoop" attributes in 4580 * upstream devices so they always generate requests with zero attributes. 4581 * 4582 * This affects other devices under the same Root Port, but since these 4583 * attributes are performance hints, there should be no functional problem. 4584 * 4585 * Note that Configuration Space accesses are never supposed to have TLP 4586 * Attributes, so we're safe waiting till after any Configuration Space 4587 * accesses to do the Root Port fixup. 4588 */ 4589 static void quirk_disable_root_port_attributes(struct pci_dev *pdev) 4590 { 4591 struct pci_dev *root_port = pcie_find_root_port(pdev); 4592 4593 if (!root_port) { 4594 pci_warn(pdev, "PCIe Completion erratum may cause device errors\n"); 4595 return; 4596 } 4597 4598 pci_info(root_port, "Disabling No Snoop/Relaxed Ordering Attributes to avoid PCIe Completion erratum in %s\n", 4599 dev_name(&pdev->dev)); 4600 pcie_capability_clear_word(root_port, PCI_EXP_DEVCTL, 4601 PCI_EXP_DEVCTL_RELAX_EN | 4602 PCI_EXP_DEVCTL_NOSNOOP_EN); 4603 } 4604 4605 /* 4606 * The Chelsio T5 chip fails to copy TLP Attributes from a Request to the 4607 * Completion it generates. 4608 */ 4609 static void quirk_chelsio_T5_disable_root_port_attributes(struct pci_dev *pdev) 4610 { 4611 /* 4612 * This mask/compare operation selects for Physical Function 4 on a 4613 * T5. We only need to fix up the Root Port once for any of the 4614 * PFs. PF[0..3] have PCI Device IDs of 0x50xx, but PF4 is uniquely 4615 * 0x54xx so we use that one. 4616 */ 4617 if ((pdev->device & 0xff00) == 0x5400) 4618 quirk_disable_root_port_attributes(pdev); 4619 } 4620 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_CHELSIO, PCI_ANY_ID, 4621 quirk_chelsio_T5_disable_root_port_attributes); 4622 4623 /* 4624 * pci_acs_ctrl_enabled - compare desired ACS controls with those provided 4625 * by a device 4626 * @acs_ctrl_req: Bitmask of desired ACS controls 4627 * @acs_ctrl_ena: Bitmask of ACS controls enabled or provided implicitly by 4628 * the hardware design 4629 * 4630 * Return 1 if all ACS controls in the @acs_ctrl_req bitmask are included 4631 * in @acs_ctrl_ena, i.e., the device provides all the access controls the 4632 * caller desires. Return 0 otherwise. 4633 */ 4634 static int pci_acs_ctrl_enabled(u16 acs_ctrl_req, u16 acs_ctrl_ena) 4635 { 4636 if ((acs_ctrl_req & acs_ctrl_ena) == acs_ctrl_req) 4637 return 1; 4638 return 0; 4639 } 4640 4641 /* 4642 * AMD has indicated that the devices below do not support peer-to-peer 4643 * in any system where they are found in the southbridge with an AMD 4644 * IOMMU in the system. Multifunction devices that do not support 4645 * peer-to-peer between functions can claim to support a subset of ACS. 4646 * Such devices effectively enable request redirect (RR) and completion 4647 * redirect (CR) since all transactions are redirected to the upstream 4648 * root complex. 4649 * 4650 * https://lore.kernel.org/r/201207111426.q6BEQTbh002928@mail.maya.org/ 4651 * https://lore.kernel.org/r/20120711165854.GM25282@amd.com/ 4652 * https://lore.kernel.org/r/20121005130857.GX4009@amd.com/ 4653 * 4654 * 1002:4385 SBx00 SMBus Controller 4655 * 1002:439c SB7x0/SB8x0/SB9x0 IDE Controller 4656 * 1002:4383 SBx00 Azalia (Intel HDA) 4657 * 1002:439d SB7x0/SB8x0/SB9x0 LPC host controller 4658 * 1002:4384 SBx00 PCI to PCI Bridge 4659 * 1002:4399 SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 4660 * 4661 * https://bugzilla.kernel.org/show_bug.cgi?id=81841#c15 4662 * 4663 * 1022:780f [AMD] FCH PCI Bridge 4664 * 1022:7809 [AMD] FCH USB OHCI Controller 4665 */ 4666 static int pci_quirk_amd_sb_acs(struct pci_dev *dev, u16 acs_flags) 4667 { 4668 #ifdef CONFIG_ACPI 4669 struct acpi_table_header *header = NULL; 4670 acpi_status status; 4671 4672 /* Targeting multifunction devices on the SB (appears on root bus) */ 4673 if (!dev->multifunction || !pci_is_root_bus(dev->bus)) 4674 return -ENODEV; 4675 4676 /* The IVRS table describes the AMD IOMMU */ 4677 status = acpi_get_table("IVRS", 0, &header); 4678 if (ACPI_FAILURE(status)) 4679 return -ENODEV; 4680 4681 acpi_put_table(header); 4682 4683 /* Filter out flags not applicable to multifunction */ 4684 acs_flags &= (PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_EC | PCI_ACS_DT); 4685 4686 return pci_acs_ctrl_enabled(acs_flags, PCI_ACS_RR | PCI_ACS_CR); 4687 #else 4688 return -ENODEV; 4689 #endif 4690 } 4691 4692 static bool pci_quirk_cavium_acs_match(struct pci_dev *dev) 4693 { 4694 if (!pci_is_pcie(dev) || pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT) 4695 return false; 4696 4697 switch (dev->device) { 4698 /* 4699 * Effectively selects all downstream ports for whole ThunderX1 4700 * (which represents 8 SoCs). 4701 */ 4702 case 0xa000 ... 0xa7ff: /* ThunderX1 */ 4703 case 0xaf84: /* ThunderX2 */ 4704 case 0xb884: /* ThunderX3 */ 4705 return true; 4706 default: 4707 return false; 4708 } 4709 } 4710 4711 static int pci_quirk_cavium_acs(struct pci_dev *dev, u16 acs_flags) 4712 { 4713 if (!pci_quirk_cavium_acs_match(dev)) 4714 return -ENOTTY; 4715 4716 /* 4717 * Cavium Root Ports don't advertise an ACS capability. However, 4718 * the RTL internally implements similar protection as if ACS had 4719 * Source Validation, Request Redirection, Completion Redirection, 4720 * and Upstream Forwarding features enabled. Assert that the 4721 * hardware implements and enables equivalent ACS functionality for 4722 * these flags. 4723 */ 4724 return pci_acs_ctrl_enabled(acs_flags, 4725 PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); 4726 } 4727 4728 static int pci_quirk_xgene_acs(struct pci_dev *dev, u16 acs_flags) 4729 { 4730 /* 4731 * X-Gene Root Ports matching this quirk do not allow peer-to-peer 4732 * transactions with others, allowing masking out these bits as if they 4733 * were unimplemented in the ACS capability. 4734 */ 4735 return pci_acs_ctrl_enabled(acs_flags, 4736 PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); 4737 } 4738 4739 /* 4740 * Many Zhaoxin Root Ports and Switch Downstream Ports have no ACS capability. 4741 * But the implementation could block peer-to-peer transactions between them 4742 * and provide ACS-like functionality. 4743 */ 4744 static int pci_quirk_zhaoxin_pcie_ports_acs(struct pci_dev *dev, u16 acs_flags) 4745 { 4746 if (!pci_is_pcie(dev) || 4747 ((pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT) && 4748 (pci_pcie_type(dev) != PCI_EXP_TYPE_DOWNSTREAM))) 4749 return -ENOTTY; 4750 4751 /* 4752 * Future Zhaoxin Root Ports and Switch Downstream Ports will 4753 * implement ACS capability in accordance with the PCIe Spec. 4754 */ 4755 switch (dev->device) { 4756 case 0x0710 ... 0x071e: 4757 case 0x0721: 4758 case 0x0723 ... 0x0752: 4759 return pci_acs_ctrl_enabled(acs_flags, 4760 PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); 4761 } 4762 4763 return false; 4764 } 4765 4766 /* 4767 * Many Intel PCH Root Ports do provide ACS-like features to disable peer 4768 * transactions and validate bus numbers in requests, but do not provide an 4769 * actual PCIe ACS capability. This is the list of device IDs known to fall 4770 * into that category as provided by Intel in Red Hat bugzilla 1037684. 4771 */ 4772 static const u16 pci_quirk_intel_pch_acs_ids[] = { 4773 /* Ibexpeak PCH */ 4774 0x3b42, 0x3b43, 0x3b44, 0x3b45, 0x3b46, 0x3b47, 0x3b48, 0x3b49, 4775 0x3b4a, 0x3b4b, 0x3b4c, 0x3b4d, 0x3b4e, 0x3b4f, 0x3b50, 0x3b51, 4776 /* Cougarpoint PCH */ 4777 0x1c10, 0x1c11, 0x1c12, 0x1c13, 0x1c14, 0x1c15, 0x1c16, 0x1c17, 4778 0x1c18, 0x1c19, 0x1c1a, 0x1c1b, 0x1c1c, 0x1c1d, 0x1c1e, 0x1c1f, 4779 /* Pantherpoint PCH */ 4780 0x1e10, 0x1e11, 0x1e12, 0x1e13, 0x1e14, 0x1e15, 0x1e16, 0x1e17, 4781 0x1e18, 0x1e19, 0x1e1a, 0x1e1b, 0x1e1c, 0x1e1d, 0x1e1e, 0x1e1f, 4782 /* Lynxpoint-H PCH */ 4783 0x8c10, 0x8c11, 0x8c12, 0x8c13, 0x8c14, 0x8c15, 0x8c16, 0x8c17, 4784 0x8c18, 0x8c19, 0x8c1a, 0x8c1b, 0x8c1c, 0x8c1d, 0x8c1e, 0x8c1f, 4785 /* Lynxpoint-LP PCH */ 4786 0x9c10, 0x9c11, 0x9c12, 0x9c13, 0x9c14, 0x9c15, 0x9c16, 0x9c17, 4787 0x9c18, 0x9c19, 0x9c1a, 0x9c1b, 4788 /* Wildcat PCH */ 4789 0x9c90, 0x9c91, 0x9c92, 0x9c93, 0x9c94, 0x9c95, 0x9c96, 0x9c97, 4790 0x9c98, 0x9c99, 0x9c9a, 0x9c9b, 4791 /* Patsburg (X79) PCH */ 4792 0x1d10, 0x1d12, 0x1d14, 0x1d16, 0x1d18, 0x1d1a, 0x1d1c, 0x1d1e, 4793 /* Wellsburg (X99) PCH */ 4794 0x8d10, 0x8d11, 0x8d12, 0x8d13, 0x8d14, 0x8d15, 0x8d16, 0x8d17, 4795 0x8d18, 0x8d19, 0x8d1a, 0x8d1b, 0x8d1c, 0x8d1d, 0x8d1e, 4796 /* Lynx Point (9 series) PCH */ 4797 0x8c90, 0x8c92, 0x8c94, 0x8c96, 0x8c98, 0x8c9a, 0x8c9c, 0x8c9e, 4798 }; 4799 4800 static bool pci_quirk_intel_pch_acs_match(struct pci_dev *dev) 4801 { 4802 int i; 4803 4804 /* Filter out a few obvious non-matches first */ 4805 if (!pci_is_pcie(dev) || pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT) 4806 return false; 4807 4808 for (i = 0; i < ARRAY_SIZE(pci_quirk_intel_pch_acs_ids); i++) 4809 if (pci_quirk_intel_pch_acs_ids[i] == dev->device) 4810 return true; 4811 4812 return false; 4813 } 4814 4815 static int pci_quirk_intel_pch_acs(struct pci_dev *dev, u16 acs_flags) 4816 { 4817 if (!pci_quirk_intel_pch_acs_match(dev)) 4818 return -ENOTTY; 4819 4820 if (dev->dev_flags & PCI_DEV_FLAGS_ACS_ENABLED_QUIRK) 4821 return pci_acs_ctrl_enabled(acs_flags, 4822 PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); 4823 4824 return pci_acs_ctrl_enabled(acs_flags, 0); 4825 } 4826 4827 /* 4828 * These QCOM Root Ports do provide ACS-like features to disable peer 4829 * transactions and validate bus numbers in requests, but do not provide an 4830 * actual PCIe ACS capability. Hardware supports source validation but it 4831 * will report the issue as Completer Abort instead of ACS Violation. 4832 * Hardware doesn't support peer-to-peer and each Root Port is a Root 4833 * Complex with unique segment numbers. It is not possible for one Root 4834 * Port to pass traffic to another Root Port. All PCIe transactions are 4835 * terminated inside the Root Port. 4836 */ 4837 static int pci_quirk_qcom_rp_acs(struct pci_dev *dev, u16 acs_flags) 4838 { 4839 return pci_acs_ctrl_enabled(acs_flags, 4840 PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); 4841 } 4842 4843 /* 4844 * Each of these NXP Root Ports is in a Root Complex with a unique segment 4845 * number and does provide isolation features to disable peer transactions 4846 * and validate bus numbers in requests, but does not provide an ACS 4847 * capability. 4848 */ 4849 static int pci_quirk_nxp_rp_acs(struct pci_dev *dev, u16 acs_flags) 4850 { 4851 return pci_acs_ctrl_enabled(acs_flags, 4852 PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); 4853 } 4854 4855 static int pci_quirk_al_acs(struct pci_dev *dev, u16 acs_flags) 4856 { 4857 if (pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT) 4858 return -ENOTTY; 4859 4860 /* 4861 * Amazon's Annapurna Labs root ports don't include an ACS capability, 4862 * but do include ACS-like functionality. The hardware doesn't support 4863 * peer-to-peer transactions via the root port and each has a unique 4864 * segment number. 4865 * 4866 * Additionally, the root ports cannot send traffic to each other. 4867 */ 4868 acs_flags &= ~(PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); 4869 4870 return acs_flags ? 0 : 1; 4871 } 4872 4873 /* 4874 * Sunrise Point PCH root ports implement ACS, but unfortunately as shown in 4875 * the datasheet (Intel 100 Series Chipset Family PCH Datasheet, Vol. 2, 4876 * 12.1.46, 12.1.47)[1] this chipset uses dwords for the ACS capability and 4877 * control registers whereas the PCIe spec packs them into words (Rev 3.0, 4878 * 7.16 ACS Extended Capability). The bit definitions are correct, but the 4879 * control register is at offset 8 instead of 6 and we should probably use 4880 * dword accesses to them. This applies to the following PCI Device IDs, as 4881 * found in volume 1 of the datasheet[2]: 4882 * 4883 * 0xa110-0xa11f Sunrise Point-H PCI Express Root Port #{0-16} 4884 * 0xa167-0xa16a Sunrise Point-H PCI Express Root Port #{17-20} 4885 * 4886 * N.B. This doesn't fix what lspci shows. 4887 * 4888 * The 100 series chipset specification update includes this as errata #23[3]. 4889 * 4890 * The 200 series chipset (Union Point) has the same bug according to the 4891 * specification update (Intel 200 Series Chipset Family Platform Controller 4892 * Hub, Specification Update, January 2017, Revision 001, Document# 335194-001, 4893 * Errata 22)[4]. Per the datasheet[5], root port PCI Device IDs for this 4894 * chipset include: 4895 * 4896 * 0xa290-0xa29f PCI Express Root port #{0-16} 4897 * 0xa2e7-0xa2ee PCI Express Root port #{17-24} 4898 * 4899 * Mobile chipsets are also affected, 7th & 8th Generation 4900 * Specification update confirms ACS errata 22, status no fix: (7th Generation 4901 * Intel Processor Family I/O for U/Y Platforms and 8th Generation Intel 4902 * Processor Family I/O for U Quad Core Platforms Specification Update, 4903 * August 2017, Revision 002, Document#: 334660-002)[6] 4904 * Device IDs from I/O datasheet: (7th Generation Intel Processor Family I/O 4905 * for U/Y Platforms and 8th Generation Intel ® Processor Family I/O for U 4906 * Quad Core Platforms, Vol 1 of 2, August 2017, Document#: 334658-003)[7] 4907 * 4908 * 0x9d10-0x9d1b PCI Express Root port #{1-12} 4909 * 4910 * [1] https://www.intel.com/content/www/us/en/chipsets/100-series-chipset-datasheet-vol-2.html 4911 * [2] https://www.intel.com/content/www/us/en/chipsets/100-series-chipset-datasheet-vol-1.html 4912 * [3] https://www.intel.com/content/www/us/en/chipsets/100-series-chipset-spec-update.html 4913 * [4] https://www.intel.com/content/www/us/en/chipsets/200-series-chipset-pch-spec-update.html 4914 * [5] https://www.intel.com/content/www/us/en/chipsets/200-series-chipset-pch-datasheet-vol-1.html 4915 * [6] https://www.intel.com/content/www/us/en/processors/core/7th-gen-core-family-mobile-u-y-processor-lines-i-o-spec-update.html 4916 * [7] https://www.intel.com/content/www/us/en/processors/core/7th-gen-core-family-mobile-u-y-processor-lines-i-o-datasheet-vol-1.html 4917 */ 4918 static bool pci_quirk_intel_spt_pch_acs_match(struct pci_dev *dev) 4919 { 4920 if (!pci_is_pcie(dev) || pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT) 4921 return false; 4922 4923 switch (dev->device) { 4924 case 0xa110 ... 0xa11f: case 0xa167 ... 0xa16a: /* Sunrise Point */ 4925 case 0xa290 ... 0xa29f: case 0xa2e7 ... 0xa2ee: /* Union Point */ 4926 case 0x9d10 ... 0x9d1b: /* 7th & 8th Gen Mobile */ 4927 return true; 4928 } 4929 4930 return false; 4931 } 4932 4933 #define INTEL_SPT_ACS_CTRL (PCI_ACS_CAP + 4) 4934 4935 static int pci_quirk_intel_spt_pch_acs(struct pci_dev *dev, u16 acs_flags) 4936 { 4937 int pos; 4938 u32 cap, ctrl; 4939 4940 if (!pci_quirk_intel_spt_pch_acs_match(dev)) 4941 return -ENOTTY; 4942 4943 pos = dev->acs_cap; 4944 if (!pos) 4945 return -ENOTTY; 4946 4947 /* see pci_acs_flags_enabled() */ 4948 pci_read_config_dword(dev, pos + PCI_ACS_CAP, &cap); 4949 acs_flags &= (cap | PCI_ACS_EC); 4950 4951 pci_read_config_dword(dev, pos + INTEL_SPT_ACS_CTRL, &ctrl); 4952 4953 return pci_acs_ctrl_enabled(acs_flags, ctrl); 4954 } 4955 4956 static int pci_quirk_mf_endpoint_acs(struct pci_dev *dev, u16 acs_flags) 4957 { 4958 /* 4959 * SV, TB, and UF are not relevant to multifunction endpoints. 4960 * 4961 * Multifunction devices are only required to implement RR, CR, and DT 4962 * in their ACS capability if they support peer-to-peer transactions. 4963 * Devices matching this quirk have been verified by the vendor to not 4964 * perform peer-to-peer with other functions, allowing us to mask out 4965 * these bits as if they were unimplemented in the ACS capability. 4966 */ 4967 return pci_acs_ctrl_enabled(acs_flags, 4968 PCI_ACS_SV | PCI_ACS_TB | PCI_ACS_RR | 4969 PCI_ACS_CR | PCI_ACS_UF | PCI_ACS_DT); 4970 } 4971 4972 static int pci_quirk_rciep_acs(struct pci_dev *dev, u16 acs_flags) 4973 { 4974 /* 4975 * Intel RCiEP's are required to allow p2p only on translated 4976 * addresses. Refer to Intel VT-d specification, r3.1, sec 3.16, 4977 * "Root-Complex Peer to Peer Considerations". 4978 */ 4979 if (pci_pcie_type(dev) != PCI_EXP_TYPE_RC_END) 4980 return -ENOTTY; 4981 4982 return pci_acs_ctrl_enabled(acs_flags, 4983 PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); 4984 } 4985 4986 static int pci_quirk_brcm_acs(struct pci_dev *dev, u16 acs_flags) 4987 { 4988 /* 4989 * iProc PAXB Root Ports don't advertise an ACS capability, but 4990 * they do not allow peer-to-peer transactions between Root Ports. 4991 * Allow each Root Port to be in a separate IOMMU group by masking 4992 * SV/RR/CR/UF bits. 4993 */ 4994 return pci_acs_ctrl_enabled(acs_flags, 4995 PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); 4996 } 4997 4998 /* 4999 * Wangxun 10G/1G NICs have no ACS capability, and on multi-function 5000 * devices, peer-to-peer transactions are not be used between the functions. 5001 * So add an ACS quirk for below devices to isolate functions. 5002 * SFxxx 1G NICs(em). 5003 * RP1000/RP2000 10G NICs(sp). 5004 */ 5005 static int pci_quirk_wangxun_nic_acs(struct pci_dev *dev, u16 acs_flags) 5006 { 5007 switch (dev->device) { 5008 case 0x0100 ... 0x010F: 5009 case 0x1001: 5010 case 0x2001: 5011 return pci_acs_ctrl_enabled(acs_flags, 5012 PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF); 5013 } 5014 5015 return false; 5016 } 5017 5018 static const struct pci_dev_acs_enabled { 5019 u16 vendor; 5020 u16 device; 5021 int (*acs_enabled)(struct pci_dev *dev, u16 acs_flags); 5022 } pci_dev_acs_enabled[] = { 5023 { PCI_VENDOR_ID_ATI, 0x4385, pci_quirk_amd_sb_acs }, 5024 { PCI_VENDOR_ID_ATI, 0x439c, pci_quirk_amd_sb_acs }, 5025 { PCI_VENDOR_ID_ATI, 0x4383, pci_quirk_amd_sb_acs }, 5026 { PCI_VENDOR_ID_ATI, 0x439d, pci_quirk_amd_sb_acs }, 5027 { PCI_VENDOR_ID_ATI, 0x4384, pci_quirk_amd_sb_acs }, 5028 { PCI_VENDOR_ID_ATI, 0x4399, pci_quirk_amd_sb_acs }, 5029 { PCI_VENDOR_ID_AMD, 0x780f, pci_quirk_amd_sb_acs }, 5030 { PCI_VENDOR_ID_AMD, 0x7809, pci_quirk_amd_sb_acs }, 5031 { PCI_VENDOR_ID_SOLARFLARE, 0x0903, pci_quirk_mf_endpoint_acs }, 5032 { PCI_VENDOR_ID_SOLARFLARE, 0x0923, pci_quirk_mf_endpoint_acs }, 5033 { PCI_VENDOR_ID_SOLARFLARE, 0x0A03, pci_quirk_mf_endpoint_acs }, 5034 { PCI_VENDOR_ID_INTEL, 0x10C6, pci_quirk_mf_endpoint_acs }, 5035 { PCI_VENDOR_ID_INTEL, 0x10DB, pci_quirk_mf_endpoint_acs }, 5036 { PCI_VENDOR_ID_INTEL, 0x10DD, pci_quirk_mf_endpoint_acs }, 5037 { PCI_VENDOR_ID_INTEL, 0x10E1, pci_quirk_mf_endpoint_acs }, 5038 { PCI_VENDOR_ID_INTEL, 0x10F1, pci_quirk_mf_endpoint_acs }, 5039 { PCI_VENDOR_ID_INTEL, 0x10F7, pci_quirk_mf_endpoint_acs }, 5040 { PCI_VENDOR_ID_INTEL, 0x10F8, pci_quirk_mf_endpoint_acs }, 5041 { PCI_VENDOR_ID_INTEL, 0x10F9, pci_quirk_mf_endpoint_acs }, 5042 { PCI_VENDOR_ID_INTEL, 0x10FA, pci_quirk_mf_endpoint_acs }, 5043 { PCI_VENDOR_ID_INTEL, 0x10FB, pci_quirk_mf_endpoint_acs }, 5044 { PCI_VENDOR_ID_INTEL, 0x10FC, pci_quirk_mf_endpoint_acs }, 5045 { PCI_VENDOR_ID_INTEL, 0x1507, pci_quirk_mf_endpoint_acs }, 5046 { PCI_VENDOR_ID_INTEL, 0x1514, pci_quirk_mf_endpoint_acs }, 5047 { PCI_VENDOR_ID_INTEL, 0x151C, pci_quirk_mf_endpoint_acs }, 5048 { PCI_VENDOR_ID_INTEL, 0x1529, pci_quirk_mf_endpoint_acs }, 5049 { PCI_VENDOR_ID_INTEL, 0x152A, pci_quirk_mf_endpoint_acs }, 5050 { PCI_VENDOR_ID_INTEL, 0x154D, pci_quirk_mf_endpoint_acs }, 5051 { PCI_VENDOR_ID_INTEL, 0x154F, pci_quirk_mf_endpoint_acs }, 5052 { PCI_VENDOR_ID_INTEL, 0x1551, pci_quirk_mf_endpoint_acs }, 5053 { PCI_VENDOR_ID_INTEL, 0x1558, pci_quirk_mf_endpoint_acs }, 5054 /* 82580 */ 5055 { PCI_VENDOR_ID_INTEL, 0x1509, pci_quirk_mf_endpoint_acs }, 5056 { PCI_VENDOR_ID_INTEL, 0x150E, pci_quirk_mf_endpoint_acs }, 5057 { PCI_VENDOR_ID_INTEL, 0x150F, pci_quirk_mf_endpoint_acs }, 5058 { PCI_VENDOR_ID_INTEL, 0x1510, pci_quirk_mf_endpoint_acs }, 5059 { PCI_VENDOR_ID_INTEL, 0x1511, pci_quirk_mf_endpoint_acs }, 5060 { PCI_VENDOR_ID_INTEL, 0x1516, pci_quirk_mf_endpoint_acs }, 5061 { PCI_VENDOR_ID_INTEL, 0x1527, pci_quirk_mf_endpoint_acs }, 5062 /* 82576 */ 5063 { PCI_VENDOR_ID_INTEL, 0x10C9, pci_quirk_mf_endpoint_acs }, 5064 { PCI_VENDOR_ID_INTEL, 0x10E6, pci_quirk_mf_endpoint_acs }, 5065 { PCI_VENDOR_ID_INTEL, 0x10E7, pci_quirk_mf_endpoint_acs }, 5066 { PCI_VENDOR_ID_INTEL, 0x10E8, pci_quirk_mf_endpoint_acs }, 5067 { PCI_VENDOR_ID_INTEL, 0x150A, pci_quirk_mf_endpoint_acs }, 5068 { PCI_VENDOR_ID_INTEL, 0x150D, pci_quirk_mf_endpoint_acs }, 5069 { PCI_VENDOR_ID_INTEL, 0x1518, pci_quirk_mf_endpoint_acs }, 5070 { PCI_VENDOR_ID_INTEL, 0x1526, pci_quirk_mf_endpoint_acs }, 5071 /* 82575 */ 5072 { PCI_VENDOR_ID_INTEL, 0x10A7, pci_quirk_mf_endpoint_acs }, 5073 { PCI_VENDOR_ID_INTEL, 0x10A9, pci_quirk_mf_endpoint_acs }, 5074 { PCI_VENDOR_ID_INTEL, 0x10D6, pci_quirk_mf_endpoint_acs }, 5075 /* I350 */ 5076 { PCI_VENDOR_ID_INTEL, 0x1521, pci_quirk_mf_endpoint_acs }, 5077 { PCI_VENDOR_ID_INTEL, 0x1522, pci_quirk_mf_endpoint_acs }, 5078 { PCI_VENDOR_ID_INTEL, 0x1523, pci_quirk_mf_endpoint_acs }, 5079 { PCI_VENDOR_ID_INTEL, 0x1524, pci_quirk_mf_endpoint_acs }, 5080 /* 82571 (Quads omitted due to non-ACS switch) */ 5081 { PCI_VENDOR_ID_INTEL, 0x105E, pci_quirk_mf_endpoint_acs }, 5082 { PCI_VENDOR_ID_INTEL, 0x105F, pci_quirk_mf_endpoint_acs }, 5083 { PCI_VENDOR_ID_INTEL, 0x1060, pci_quirk_mf_endpoint_acs }, 5084 { PCI_VENDOR_ID_INTEL, 0x10D9, pci_quirk_mf_endpoint_acs }, 5085 /* I219 */ 5086 { PCI_VENDOR_ID_INTEL, 0x15b7, pci_quirk_mf_endpoint_acs }, 5087 { PCI_VENDOR_ID_INTEL, 0x15b8, pci_quirk_mf_endpoint_acs }, 5088 { PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_quirk_rciep_acs }, 5089 /* QCOM QDF2xxx root ports */ 5090 { PCI_VENDOR_ID_QCOM, 0x0400, pci_quirk_qcom_rp_acs }, 5091 { PCI_VENDOR_ID_QCOM, 0x0401, pci_quirk_qcom_rp_acs }, 5092 /* QCOM SA8775P root port */ 5093 { PCI_VENDOR_ID_QCOM, 0x0115, pci_quirk_qcom_rp_acs }, 5094 /* HXT SD4800 root ports. The ACS design is same as QCOM QDF2xxx */ 5095 { PCI_VENDOR_ID_HXT, 0x0401, pci_quirk_qcom_rp_acs }, 5096 /* Intel PCH root ports */ 5097 { PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_quirk_intel_pch_acs }, 5098 { PCI_VENDOR_ID_INTEL, PCI_ANY_ID, pci_quirk_intel_spt_pch_acs }, 5099 { 0x19a2, 0x710, pci_quirk_mf_endpoint_acs }, /* Emulex BE3-R */ 5100 { 0x10df, 0x720, pci_quirk_mf_endpoint_acs }, /* Emulex Skyhawk-R */ 5101 /* Cavium ThunderX */ 5102 { PCI_VENDOR_ID_CAVIUM, PCI_ANY_ID, pci_quirk_cavium_acs }, 5103 /* Cavium multi-function devices */ 5104 { PCI_VENDOR_ID_CAVIUM, 0xA026, pci_quirk_mf_endpoint_acs }, 5105 { PCI_VENDOR_ID_CAVIUM, 0xA059, pci_quirk_mf_endpoint_acs }, 5106 { PCI_VENDOR_ID_CAVIUM, 0xA060, pci_quirk_mf_endpoint_acs }, 5107 /* APM X-Gene */ 5108 { PCI_VENDOR_ID_AMCC, 0xE004, pci_quirk_xgene_acs }, 5109 /* Ampere Computing */ 5110 { PCI_VENDOR_ID_AMPERE, 0xE005, pci_quirk_xgene_acs }, 5111 { PCI_VENDOR_ID_AMPERE, 0xE006, pci_quirk_xgene_acs }, 5112 { PCI_VENDOR_ID_AMPERE, 0xE007, pci_quirk_xgene_acs }, 5113 { PCI_VENDOR_ID_AMPERE, 0xE008, pci_quirk_xgene_acs }, 5114 { PCI_VENDOR_ID_AMPERE, 0xE009, pci_quirk_xgene_acs }, 5115 { PCI_VENDOR_ID_AMPERE, 0xE00A, pci_quirk_xgene_acs }, 5116 { PCI_VENDOR_ID_AMPERE, 0xE00B, pci_quirk_xgene_acs }, 5117 { PCI_VENDOR_ID_AMPERE, 0xE00C, pci_quirk_xgene_acs }, 5118 /* Broadcom multi-function device */ 5119 { PCI_VENDOR_ID_BROADCOM, 0x16D7, pci_quirk_mf_endpoint_acs }, 5120 { PCI_VENDOR_ID_BROADCOM, 0x1750, pci_quirk_mf_endpoint_acs }, 5121 { PCI_VENDOR_ID_BROADCOM, 0x1751, pci_quirk_mf_endpoint_acs }, 5122 { PCI_VENDOR_ID_BROADCOM, 0x1752, pci_quirk_mf_endpoint_acs }, 5123 { PCI_VENDOR_ID_BROADCOM, 0x1760, pci_quirk_mf_endpoint_acs }, 5124 { PCI_VENDOR_ID_BROADCOM, 0x1761, pci_quirk_mf_endpoint_acs }, 5125 { PCI_VENDOR_ID_BROADCOM, 0x1762, pci_quirk_mf_endpoint_acs }, 5126 { PCI_VENDOR_ID_BROADCOM, 0x1763, pci_quirk_mf_endpoint_acs }, 5127 { PCI_VENDOR_ID_BROADCOM, 0xD714, pci_quirk_brcm_acs }, 5128 /* Amazon Annapurna Labs */ 5129 { PCI_VENDOR_ID_AMAZON_ANNAPURNA_LABS, 0x0031, pci_quirk_al_acs }, 5130 /* Zhaoxin multi-function devices */ 5131 { PCI_VENDOR_ID_ZHAOXIN, 0x3038, pci_quirk_mf_endpoint_acs }, 5132 { PCI_VENDOR_ID_ZHAOXIN, 0x3104, pci_quirk_mf_endpoint_acs }, 5133 { PCI_VENDOR_ID_ZHAOXIN, 0x9083, pci_quirk_mf_endpoint_acs }, 5134 /* NXP root ports, xx=16, 12, or 08 cores */ 5135 /* LX2xx0A : without security features + CAN-FD */ 5136 { PCI_VENDOR_ID_NXP, 0x8d81, pci_quirk_nxp_rp_acs }, 5137 { PCI_VENDOR_ID_NXP, 0x8da1, pci_quirk_nxp_rp_acs }, 5138 { PCI_VENDOR_ID_NXP, 0x8d83, pci_quirk_nxp_rp_acs }, 5139 /* LX2xx0C : security features + CAN-FD */ 5140 { PCI_VENDOR_ID_NXP, 0x8d80, pci_quirk_nxp_rp_acs }, 5141 { PCI_VENDOR_ID_NXP, 0x8da0, pci_quirk_nxp_rp_acs }, 5142 { PCI_VENDOR_ID_NXP, 0x8d82, pci_quirk_nxp_rp_acs }, 5143 /* LX2xx0E : security features + CAN */ 5144 { PCI_VENDOR_ID_NXP, 0x8d90, pci_quirk_nxp_rp_acs }, 5145 { PCI_VENDOR_ID_NXP, 0x8db0, pci_quirk_nxp_rp_acs }, 5146 { PCI_VENDOR_ID_NXP, 0x8d92, pci_quirk_nxp_rp_acs }, 5147 /* LX2xx0N : without security features + CAN */ 5148 { PCI_VENDOR_ID_NXP, 0x8d91, pci_quirk_nxp_rp_acs }, 5149 { PCI_VENDOR_ID_NXP, 0x8db1, pci_quirk_nxp_rp_acs }, 5150 { PCI_VENDOR_ID_NXP, 0x8d93, pci_quirk_nxp_rp_acs }, 5151 /* LX2xx2A : without security features + CAN-FD */ 5152 { PCI_VENDOR_ID_NXP, 0x8d89, pci_quirk_nxp_rp_acs }, 5153 { PCI_VENDOR_ID_NXP, 0x8da9, pci_quirk_nxp_rp_acs }, 5154 { PCI_VENDOR_ID_NXP, 0x8d8b, pci_quirk_nxp_rp_acs }, 5155 /* LX2xx2C : security features + CAN-FD */ 5156 { PCI_VENDOR_ID_NXP, 0x8d88, pci_quirk_nxp_rp_acs }, 5157 { PCI_VENDOR_ID_NXP, 0x8da8, pci_quirk_nxp_rp_acs }, 5158 { PCI_VENDOR_ID_NXP, 0x8d8a, pci_quirk_nxp_rp_acs }, 5159 /* LX2xx2E : security features + CAN */ 5160 { PCI_VENDOR_ID_NXP, 0x8d98, pci_quirk_nxp_rp_acs }, 5161 { PCI_VENDOR_ID_NXP, 0x8db8, pci_quirk_nxp_rp_acs }, 5162 { PCI_VENDOR_ID_NXP, 0x8d9a, pci_quirk_nxp_rp_acs }, 5163 /* LX2xx2N : without security features + CAN */ 5164 { PCI_VENDOR_ID_NXP, 0x8d99, pci_quirk_nxp_rp_acs }, 5165 { PCI_VENDOR_ID_NXP, 0x8db9, pci_quirk_nxp_rp_acs }, 5166 { PCI_VENDOR_ID_NXP, 0x8d9b, pci_quirk_nxp_rp_acs }, 5167 /* Zhaoxin Root/Downstream Ports */ 5168 { PCI_VENDOR_ID_ZHAOXIN, PCI_ANY_ID, pci_quirk_zhaoxin_pcie_ports_acs }, 5169 /* Wangxun nics */ 5170 { PCI_VENDOR_ID_WANGXUN, PCI_ANY_ID, pci_quirk_wangxun_nic_acs }, 5171 { 0 } 5172 }; 5173 5174 /* 5175 * pci_dev_specific_acs_enabled - check whether device provides ACS controls 5176 * @dev: PCI device 5177 * @acs_flags: Bitmask of desired ACS controls 5178 * 5179 * Returns: 5180 * -ENOTTY: No quirk applies to this device; we can't tell whether the 5181 * device provides the desired controls 5182 * 0: Device does not provide all the desired controls 5183 * >0: Device provides all the controls in @acs_flags 5184 */ 5185 int pci_dev_specific_acs_enabled(struct pci_dev *dev, u16 acs_flags) 5186 { 5187 const struct pci_dev_acs_enabled *i; 5188 int ret; 5189 5190 /* 5191 * Allow devices that do not expose standard PCIe ACS capabilities 5192 * or control to indicate their support here. Multi-function express 5193 * devices which do not allow internal peer-to-peer between functions, 5194 * but do not implement PCIe ACS may wish to return true here. 5195 */ 5196 for (i = pci_dev_acs_enabled; i->acs_enabled; i++) { 5197 if ((i->vendor == dev->vendor || 5198 i->vendor == (u16)PCI_ANY_ID) && 5199 (i->device == dev->device || 5200 i->device == (u16)PCI_ANY_ID)) { 5201 ret = i->acs_enabled(dev, acs_flags); 5202 if (ret >= 0) 5203 return ret; 5204 } 5205 } 5206 5207 return -ENOTTY; 5208 } 5209 5210 /* Config space offset of Root Complex Base Address register */ 5211 #define INTEL_LPC_RCBA_REG 0xf0 5212 /* 31:14 RCBA address */ 5213 #define INTEL_LPC_RCBA_MASK 0xffffc000 5214 /* RCBA Enable */ 5215 #define INTEL_LPC_RCBA_ENABLE (1 << 0) 5216 5217 /* Backbone Scratch Pad Register */ 5218 #define INTEL_BSPR_REG 0x1104 5219 /* Backbone Peer Non-Posted Disable */ 5220 #define INTEL_BSPR_REG_BPNPD (1 << 8) 5221 /* Backbone Peer Posted Disable */ 5222 #define INTEL_BSPR_REG_BPPD (1 << 9) 5223 5224 /* Upstream Peer Decode Configuration Register */ 5225 #define INTEL_UPDCR_REG 0x1014 5226 /* 5:0 Peer Decode Enable bits */ 5227 #define INTEL_UPDCR_REG_MASK 0x3f 5228 5229 static int pci_quirk_enable_intel_lpc_acs(struct pci_dev *dev) 5230 { 5231 u32 rcba, bspr, updcr; 5232 void __iomem *rcba_mem; 5233 5234 /* 5235 * Read the RCBA register from the LPC (D31:F0). PCH root ports 5236 * are D28:F* and therefore get probed before LPC, thus we can't 5237 * use pci_get_slot()/pci_read_config_dword() here. 5238 */ 5239 pci_bus_read_config_dword(dev->bus, PCI_DEVFN(31, 0), 5240 INTEL_LPC_RCBA_REG, &rcba); 5241 if (!(rcba & INTEL_LPC_RCBA_ENABLE)) 5242 return -EINVAL; 5243 5244 rcba_mem = ioremap(rcba & INTEL_LPC_RCBA_MASK, 5245 PAGE_ALIGN(INTEL_UPDCR_REG)); 5246 if (!rcba_mem) 5247 return -ENOMEM; 5248 5249 /* 5250 * The BSPR can disallow peer cycles, but it's set by soft strap and 5251 * therefore read-only. If both posted and non-posted peer cycles are 5252 * disallowed, we're ok. If either are allowed, then we need to use 5253 * the UPDCR to disable peer decodes for each port. This provides the 5254 * PCIe ACS equivalent of PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF 5255 */ 5256 bspr = readl(rcba_mem + INTEL_BSPR_REG); 5257 bspr &= INTEL_BSPR_REG_BPNPD | INTEL_BSPR_REG_BPPD; 5258 if (bspr != (INTEL_BSPR_REG_BPNPD | INTEL_BSPR_REG_BPPD)) { 5259 updcr = readl(rcba_mem + INTEL_UPDCR_REG); 5260 if (updcr & INTEL_UPDCR_REG_MASK) { 5261 pci_info(dev, "Disabling UPDCR peer decodes\n"); 5262 updcr &= ~INTEL_UPDCR_REG_MASK; 5263 writel(updcr, rcba_mem + INTEL_UPDCR_REG); 5264 } 5265 } 5266 5267 iounmap(rcba_mem); 5268 return 0; 5269 } 5270 5271 /* Miscellaneous Port Configuration register */ 5272 #define INTEL_MPC_REG 0xd8 5273 /* MPC: Invalid Receive Bus Number Check Enable */ 5274 #define INTEL_MPC_REG_IRBNCE (1 << 26) 5275 5276 static void pci_quirk_enable_intel_rp_mpc_acs(struct pci_dev *dev) 5277 { 5278 u32 mpc; 5279 5280 /* 5281 * When enabled, the IRBNCE bit of the MPC register enables the 5282 * equivalent of PCI ACS Source Validation (PCI_ACS_SV), which 5283 * ensures that requester IDs fall within the bus number range 5284 * of the bridge. Enable if not already. 5285 */ 5286 pci_read_config_dword(dev, INTEL_MPC_REG, &mpc); 5287 if (!(mpc & INTEL_MPC_REG_IRBNCE)) { 5288 pci_info(dev, "Enabling MPC IRBNCE\n"); 5289 mpc |= INTEL_MPC_REG_IRBNCE; 5290 pci_write_config_word(dev, INTEL_MPC_REG, mpc); 5291 } 5292 } 5293 5294 /* 5295 * Currently this quirk does the equivalent of 5296 * PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF 5297 * 5298 * TODO: This quirk also needs to do equivalent of PCI_ACS_TB, 5299 * if dev->external_facing || dev->untrusted 5300 */ 5301 static int pci_quirk_enable_intel_pch_acs(struct pci_dev *dev) 5302 { 5303 if (!pci_quirk_intel_pch_acs_match(dev)) 5304 return -ENOTTY; 5305 5306 if (pci_quirk_enable_intel_lpc_acs(dev)) { 5307 pci_warn(dev, "Failed to enable Intel PCH ACS quirk\n"); 5308 return 0; 5309 } 5310 5311 pci_quirk_enable_intel_rp_mpc_acs(dev); 5312 5313 dev->dev_flags |= PCI_DEV_FLAGS_ACS_ENABLED_QUIRK; 5314 5315 pci_info(dev, "Intel PCH root port ACS workaround enabled\n"); 5316 5317 return 0; 5318 } 5319 5320 static int pci_quirk_enable_intel_spt_pch_acs(struct pci_dev *dev) 5321 { 5322 int pos; 5323 u32 cap, ctrl; 5324 5325 if (!pci_quirk_intel_spt_pch_acs_match(dev)) 5326 return -ENOTTY; 5327 5328 pos = dev->acs_cap; 5329 if (!pos) 5330 return -ENOTTY; 5331 5332 pci_read_config_dword(dev, pos + PCI_ACS_CAP, &cap); 5333 pci_read_config_dword(dev, pos + INTEL_SPT_ACS_CTRL, &ctrl); 5334 5335 ctrl |= (cap & PCI_ACS_SV); 5336 ctrl |= (cap & PCI_ACS_RR); 5337 ctrl |= (cap & PCI_ACS_CR); 5338 ctrl |= (cap & PCI_ACS_UF); 5339 5340 if (pci_ats_disabled() || dev->external_facing || dev->untrusted) 5341 ctrl |= (cap & PCI_ACS_TB); 5342 5343 pci_write_config_dword(dev, pos + INTEL_SPT_ACS_CTRL, ctrl); 5344 5345 pci_info(dev, "Intel SPT PCH root port ACS workaround enabled\n"); 5346 5347 return 0; 5348 } 5349 5350 static int pci_quirk_disable_intel_spt_pch_acs_redir(struct pci_dev *dev) 5351 { 5352 int pos; 5353 u32 cap, ctrl; 5354 5355 if (!pci_quirk_intel_spt_pch_acs_match(dev)) 5356 return -ENOTTY; 5357 5358 pos = dev->acs_cap; 5359 if (!pos) 5360 return -ENOTTY; 5361 5362 pci_read_config_dword(dev, pos + PCI_ACS_CAP, &cap); 5363 pci_read_config_dword(dev, pos + INTEL_SPT_ACS_CTRL, &ctrl); 5364 5365 ctrl &= ~(PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_EC); 5366 5367 pci_write_config_dword(dev, pos + INTEL_SPT_ACS_CTRL, ctrl); 5368 5369 pci_info(dev, "Intel SPT PCH root port workaround: disabled ACS redirect\n"); 5370 5371 return 0; 5372 } 5373 5374 static const struct pci_dev_acs_ops { 5375 u16 vendor; 5376 u16 device; 5377 int (*enable_acs)(struct pci_dev *dev); 5378 int (*disable_acs_redir)(struct pci_dev *dev); 5379 } pci_dev_acs_ops[] = { 5380 { PCI_VENDOR_ID_INTEL, PCI_ANY_ID, 5381 .enable_acs = pci_quirk_enable_intel_pch_acs, 5382 }, 5383 { PCI_VENDOR_ID_INTEL, PCI_ANY_ID, 5384 .enable_acs = pci_quirk_enable_intel_spt_pch_acs, 5385 .disable_acs_redir = pci_quirk_disable_intel_spt_pch_acs_redir, 5386 }, 5387 }; 5388 5389 int pci_dev_specific_enable_acs(struct pci_dev *dev) 5390 { 5391 const struct pci_dev_acs_ops *p; 5392 int i, ret; 5393 5394 for (i = 0; i < ARRAY_SIZE(pci_dev_acs_ops); i++) { 5395 p = &pci_dev_acs_ops[i]; 5396 if ((p->vendor == dev->vendor || 5397 p->vendor == (u16)PCI_ANY_ID) && 5398 (p->device == dev->device || 5399 p->device == (u16)PCI_ANY_ID) && 5400 p->enable_acs) { 5401 ret = p->enable_acs(dev); 5402 if (ret >= 0) 5403 return ret; 5404 } 5405 } 5406 5407 return -ENOTTY; 5408 } 5409 5410 int pci_dev_specific_disable_acs_redir(struct pci_dev *dev) 5411 { 5412 const struct pci_dev_acs_ops *p; 5413 int i, ret; 5414 5415 for (i = 0; i < ARRAY_SIZE(pci_dev_acs_ops); i++) { 5416 p = &pci_dev_acs_ops[i]; 5417 if ((p->vendor == dev->vendor || 5418 p->vendor == (u16)PCI_ANY_ID) && 5419 (p->device == dev->device || 5420 p->device == (u16)PCI_ANY_ID) && 5421 p->disable_acs_redir) { 5422 ret = p->disable_acs_redir(dev); 5423 if (ret >= 0) 5424 return ret; 5425 } 5426 } 5427 5428 return -ENOTTY; 5429 } 5430 5431 /* 5432 * The PCI capabilities list for Intel DH895xCC VFs (device ID 0x0443) with 5433 * QuickAssist Technology (QAT) is prematurely terminated in hardware. The 5434 * Next Capability pointer in the MSI Capability Structure should point to 5435 * the PCIe Capability Structure but is incorrectly hardwired as 0 terminating 5436 * the list. 5437 */ 5438 static void quirk_intel_qat_vf_cap(struct pci_dev *pdev) 5439 { 5440 int pos, i = 0, ret; 5441 u8 next_cap; 5442 u16 reg16, *cap; 5443 struct pci_cap_saved_state *state; 5444 5445 /* Bail if the hardware bug is fixed */ 5446 if (pdev->pcie_cap || pci_find_capability(pdev, PCI_CAP_ID_EXP)) 5447 return; 5448 5449 /* Bail if MSI Capability Structure is not found for some reason */ 5450 pos = pci_find_capability(pdev, PCI_CAP_ID_MSI); 5451 if (!pos) 5452 return; 5453 5454 /* 5455 * Bail if Next Capability pointer in the MSI Capability Structure 5456 * is not the expected incorrect 0x00. 5457 */ 5458 pci_read_config_byte(pdev, pos + 1, &next_cap); 5459 if (next_cap) 5460 return; 5461 5462 /* 5463 * PCIe Capability Structure is expected to be at 0x50 and should 5464 * terminate the list (Next Capability pointer is 0x00). Verify 5465 * Capability Id and Next Capability pointer is as expected. 5466 * Open-code some of set_pcie_port_type() and pci_cfg_space_size_ext() 5467 * to correctly set kernel data structures which have already been 5468 * set incorrectly due to the hardware bug. 5469 */ 5470 pos = 0x50; 5471 pci_read_config_word(pdev, pos, ®16); 5472 if (reg16 == (0x0000 | PCI_CAP_ID_EXP)) { 5473 u32 status; 5474 #ifndef PCI_EXP_SAVE_REGS 5475 #define PCI_EXP_SAVE_REGS 7 5476 #endif 5477 int size = PCI_EXP_SAVE_REGS * sizeof(u16); 5478 5479 pdev->pcie_cap = pos; 5480 pci_read_config_word(pdev, pos + PCI_EXP_FLAGS, ®16); 5481 pdev->pcie_flags_reg = reg16; 5482 pci_read_config_word(pdev, pos + PCI_EXP_DEVCAP, ®16); 5483 pdev->pcie_mpss = reg16 & PCI_EXP_DEVCAP_PAYLOAD; 5484 5485 pdev->cfg_size = PCI_CFG_SPACE_EXP_SIZE; 5486 ret = pci_read_config_dword(pdev, PCI_CFG_SPACE_SIZE, &status); 5487 if ((ret != PCIBIOS_SUCCESSFUL) || (PCI_POSSIBLE_ERROR(status))) 5488 pdev->cfg_size = PCI_CFG_SPACE_SIZE; 5489 5490 if (pci_find_saved_cap(pdev, PCI_CAP_ID_EXP)) 5491 return; 5492 5493 /* Save PCIe cap */ 5494 state = kzalloc(sizeof(*state) + size, GFP_KERNEL); 5495 if (!state) 5496 return; 5497 5498 state->cap.cap_nr = PCI_CAP_ID_EXP; 5499 state->cap.cap_extended = 0; 5500 state->cap.size = size; 5501 cap = (u16 *)&state->cap.data[0]; 5502 pcie_capability_read_word(pdev, PCI_EXP_DEVCTL, &cap[i++]); 5503 pcie_capability_read_word(pdev, PCI_EXP_LNKCTL, &cap[i++]); 5504 pcie_capability_read_word(pdev, PCI_EXP_SLTCTL, &cap[i++]); 5505 pcie_capability_read_word(pdev, PCI_EXP_RTCTL, &cap[i++]); 5506 pcie_capability_read_word(pdev, PCI_EXP_DEVCTL2, &cap[i++]); 5507 pcie_capability_read_word(pdev, PCI_EXP_LNKCTL2, &cap[i++]); 5508 pcie_capability_read_word(pdev, PCI_EXP_SLTCTL2, &cap[i++]); 5509 hlist_add_head(&state->next, &pdev->saved_cap_space); 5510 } 5511 } 5512 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x443, quirk_intel_qat_vf_cap); 5513 5514 /* 5515 * FLR may cause the following to devices to hang: 5516 * 5517 * AMD Starship/Matisse HD Audio Controller 0x1487 5518 * AMD Starship USB 3.0 Host Controller 0x148c 5519 * AMD Matisse USB 3.0 Host Controller 0x149c 5520 * Intel 82579LM Gigabit Ethernet Controller 0x1502 5521 * Intel 82579V Gigabit Ethernet Controller 0x1503 5522 * 5523 */ 5524 static void quirk_no_flr(struct pci_dev *dev) 5525 { 5526 dev->dev_flags |= PCI_DEV_FLAGS_NO_FLR_RESET; 5527 } 5528 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x1487, quirk_no_flr); 5529 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x148c, quirk_no_flr); 5530 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x149c, quirk_no_flr); 5531 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x7901, quirk_no_flr); 5532 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1502, quirk_no_flr); 5533 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1503, quirk_no_flr); 5534 5535 /* FLR may cause the SolidRun SNET DPU (rev 0x1) to hang */ 5536 static void quirk_no_flr_snet(struct pci_dev *dev) 5537 { 5538 if (dev->revision == 0x1) 5539 quirk_no_flr(dev); 5540 } 5541 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SOLIDRUN, 0x1000, quirk_no_flr_snet); 5542 5543 static void quirk_no_ext_tags(struct pci_dev *pdev) 5544 { 5545 struct pci_host_bridge *bridge = pci_find_host_bridge(pdev->bus); 5546 5547 if (!bridge) 5548 return; 5549 5550 bridge->no_ext_tags = 1; 5551 pci_info(pdev, "disabling Extended Tags (this device can't handle them)\n"); 5552 5553 pci_walk_bus(bridge->bus, pci_configure_extended_tags, NULL); 5554 } 5555 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_3WARE, 0x1004, quirk_no_ext_tags); 5556 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0132, quirk_no_ext_tags); 5557 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0140, quirk_no_ext_tags); 5558 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0141, quirk_no_ext_tags); 5559 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0142, quirk_no_ext_tags); 5560 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0144, quirk_no_ext_tags); 5561 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0420, quirk_no_ext_tags); 5562 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, 0x0422, quirk_no_ext_tags); 5563 5564 #ifdef CONFIG_PCI_ATS 5565 static void quirk_no_ats(struct pci_dev *pdev) 5566 { 5567 pci_info(pdev, "disabling ATS\n"); 5568 pdev->ats_cap = 0; 5569 } 5570 5571 /* 5572 * Some devices require additional driver setup to enable ATS. Don't use 5573 * ATS for those devices as ATS will be enabled before the driver has had a 5574 * chance to load and configure the device. 5575 */ 5576 static void quirk_amd_harvest_no_ats(struct pci_dev *pdev) 5577 { 5578 if (pdev->device == 0x15d8) { 5579 if (pdev->revision == 0xcf && 5580 pdev->subsystem_vendor == 0xea50 && 5581 (pdev->subsystem_device == 0xce19 || 5582 pdev->subsystem_device == 0xcc10 || 5583 pdev->subsystem_device == 0xcc08)) 5584 quirk_no_ats(pdev); 5585 } else { 5586 quirk_no_ats(pdev); 5587 } 5588 } 5589 5590 /* AMD Stoney platform GPU */ 5591 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x98e4, quirk_amd_harvest_no_ats); 5592 /* AMD Iceland dGPU */ 5593 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x6900, quirk_amd_harvest_no_ats); 5594 /* AMD Navi10 dGPU */ 5595 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7310, quirk_amd_harvest_no_ats); 5596 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7312, quirk_amd_harvest_no_ats); 5597 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7318, quirk_amd_harvest_no_ats); 5598 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7319, quirk_amd_harvest_no_ats); 5599 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x731a, quirk_amd_harvest_no_ats); 5600 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x731b, quirk_amd_harvest_no_ats); 5601 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x731e, quirk_amd_harvest_no_ats); 5602 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x731f, quirk_amd_harvest_no_ats); 5603 /* AMD Navi14 dGPU */ 5604 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7340, quirk_amd_harvest_no_ats); 5605 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7341, quirk_amd_harvest_no_ats); 5606 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7347, quirk_amd_harvest_no_ats); 5607 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x734f, quirk_amd_harvest_no_ats); 5608 /* AMD Raven platform iGPU */ 5609 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x15d8, quirk_amd_harvest_no_ats); 5610 5611 /* 5612 * Intel IPU E2000 revisions before C0 implement incorrect endianness 5613 * in ATS Invalidate Request message body. Disable ATS for those devices. 5614 */ 5615 static void quirk_intel_e2000_no_ats(struct pci_dev *pdev) 5616 { 5617 if (pdev->revision < 0x20) 5618 quirk_no_ats(pdev); 5619 } 5620 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1451, quirk_intel_e2000_no_ats); 5621 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1452, quirk_intel_e2000_no_ats); 5622 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1453, quirk_intel_e2000_no_ats); 5623 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1454, quirk_intel_e2000_no_ats); 5624 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1455, quirk_intel_e2000_no_ats); 5625 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1457, quirk_intel_e2000_no_ats); 5626 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1459, quirk_intel_e2000_no_ats); 5627 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x145a, quirk_intel_e2000_no_ats); 5628 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x145c, quirk_intel_e2000_no_ats); 5629 #endif /* CONFIG_PCI_ATS */ 5630 5631 /* Freescale PCIe doesn't support MSI in RC mode */ 5632 static void quirk_fsl_no_msi(struct pci_dev *pdev) 5633 { 5634 if (pci_pcie_type(pdev) == PCI_EXP_TYPE_ROOT_PORT) 5635 pdev->no_msi = 1; 5636 } 5637 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_FREESCALE, PCI_ANY_ID, quirk_fsl_no_msi); 5638 5639 /* 5640 * Although not allowed by the spec, some multi-function devices have 5641 * dependencies of one function (consumer) on another (supplier). For the 5642 * consumer to work in D0, the supplier must also be in D0. Create a 5643 * device link from the consumer to the supplier to enforce this 5644 * dependency. Runtime PM is allowed by default on the consumer to prevent 5645 * it from permanently keeping the supplier awake. 5646 */ 5647 static void pci_create_device_link(struct pci_dev *pdev, unsigned int consumer, 5648 unsigned int supplier, unsigned int class, 5649 unsigned int class_shift) 5650 { 5651 struct pci_dev *supplier_pdev; 5652 5653 if (PCI_FUNC(pdev->devfn) != consumer) 5654 return; 5655 5656 supplier_pdev = pci_get_domain_bus_and_slot(pci_domain_nr(pdev->bus), 5657 pdev->bus->number, 5658 PCI_DEVFN(PCI_SLOT(pdev->devfn), supplier)); 5659 if (!supplier_pdev || (supplier_pdev->class >> class_shift) != class) { 5660 pci_dev_put(supplier_pdev); 5661 return; 5662 } 5663 5664 if (device_link_add(&pdev->dev, &supplier_pdev->dev, 5665 DL_FLAG_STATELESS | DL_FLAG_PM_RUNTIME)) 5666 pci_info(pdev, "D0 power state depends on %s\n", 5667 pci_name(supplier_pdev)); 5668 else 5669 pci_err(pdev, "Cannot enforce power dependency on %s\n", 5670 pci_name(supplier_pdev)); 5671 5672 pm_runtime_allow(&pdev->dev); 5673 pci_dev_put(supplier_pdev); 5674 } 5675 5676 /* 5677 * Create device link for GPUs with integrated HDA controller for streaming 5678 * audio to attached displays. 5679 */ 5680 static void quirk_gpu_hda(struct pci_dev *hda) 5681 { 5682 pci_create_device_link(hda, 1, 0, PCI_BASE_CLASS_DISPLAY, 16); 5683 } 5684 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_ATI, PCI_ANY_ID, 5685 PCI_CLASS_MULTIMEDIA_HD_AUDIO, 8, quirk_gpu_hda); 5686 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_AMD, PCI_ANY_ID, 5687 PCI_CLASS_MULTIMEDIA_HD_AUDIO, 8, quirk_gpu_hda); 5688 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, 5689 PCI_CLASS_MULTIMEDIA_HD_AUDIO, 8, quirk_gpu_hda); 5690 5691 /* 5692 * Create device link for GPUs with integrated USB xHCI Host 5693 * controller to VGA. 5694 */ 5695 static void quirk_gpu_usb(struct pci_dev *usb) 5696 { 5697 pci_create_device_link(usb, 2, 0, PCI_BASE_CLASS_DISPLAY, 16); 5698 } 5699 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, 5700 PCI_CLASS_SERIAL_USB, 8, quirk_gpu_usb); 5701 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_ATI, PCI_ANY_ID, 5702 PCI_CLASS_SERIAL_USB, 8, quirk_gpu_usb); 5703 5704 /* 5705 * Create device link for GPUs with integrated Type-C UCSI controller 5706 * to VGA. Currently there is no class code defined for UCSI device over PCI 5707 * so using UNKNOWN class for now and it will be updated when UCSI 5708 * over PCI gets a class code. 5709 */ 5710 #define PCI_CLASS_SERIAL_UNKNOWN 0x0c80 5711 static void quirk_gpu_usb_typec_ucsi(struct pci_dev *ucsi) 5712 { 5713 pci_create_device_link(ucsi, 3, 0, PCI_BASE_CLASS_DISPLAY, 16); 5714 } 5715 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, 5716 PCI_CLASS_SERIAL_UNKNOWN, 8, 5717 quirk_gpu_usb_typec_ucsi); 5718 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_ATI, PCI_ANY_ID, 5719 PCI_CLASS_SERIAL_UNKNOWN, 8, 5720 quirk_gpu_usb_typec_ucsi); 5721 5722 /* 5723 * Enable the NVIDIA GPU integrated HDA controller if the BIOS left it 5724 * disabled. https://devtalk.nvidia.com/default/topic/1024022 5725 */ 5726 static void quirk_nvidia_hda(struct pci_dev *gpu) 5727 { 5728 u8 hdr_type; 5729 u32 val; 5730 5731 /* There was no integrated HDA controller before MCP89 */ 5732 if (gpu->device < PCI_DEVICE_ID_NVIDIA_GEFORCE_320M) 5733 return; 5734 5735 /* Bit 25 at offset 0x488 enables the HDA controller */ 5736 pci_read_config_dword(gpu, 0x488, &val); 5737 if (val & BIT(25)) 5738 return; 5739 5740 pci_info(gpu, "Enabling HDA controller\n"); 5741 pci_write_config_dword(gpu, 0x488, val | BIT(25)); 5742 5743 /* The GPU becomes a multi-function device when the HDA is enabled */ 5744 pci_read_config_byte(gpu, PCI_HEADER_TYPE, &hdr_type); 5745 gpu->multifunction = FIELD_GET(PCI_HEADER_TYPE_MFD, hdr_type); 5746 } 5747 DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, 5748 PCI_BASE_CLASS_DISPLAY, 16, quirk_nvidia_hda); 5749 DECLARE_PCI_FIXUP_CLASS_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, 5750 PCI_BASE_CLASS_DISPLAY, 16, quirk_nvidia_hda); 5751 5752 /* 5753 * Some IDT switches incorrectly flag an ACS Source Validation error on 5754 * completions for config read requests even though PCIe r4.0, sec 5755 * 6.12.1.1, says that completions are never affected by ACS Source 5756 * Validation. Here's the text of IDT 89H32H8G3-YC, erratum #36: 5757 * 5758 * Item #36 - Downstream port applies ACS Source Validation to Completions 5759 * Section 6.12.1.1 of the PCI Express Base Specification 3.1 states that 5760 * completions are never affected by ACS Source Validation. However, 5761 * completions received by a downstream port of the PCIe switch from a 5762 * device that has not yet captured a PCIe bus number are incorrectly 5763 * dropped by ACS Source Validation by the switch downstream port. 5764 * 5765 * The workaround suggested by IDT is to issue a config write to the 5766 * downstream device before issuing the first config read. This allows the 5767 * downstream device to capture its bus and device numbers (see PCIe r4.0, 5768 * sec 2.2.9), thus avoiding the ACS error on the completion. 5769 * 5770 * However, we don't know when the device is ready to accept the config 5771 * write, so we do config reads until we receive a non-Config Request Retry 5772 * Status, then do the config write. 5773 * 5774 * To avoid hitting the erratum when doing the config reads, we disable ACS 5775 * SV around this process. 5776 */ 5777 int pci_idt_bus_quirk(struct pci_bus *bus, int devfn, u32 *l, int timeout) 5778 { 5779 int pos; 5780 u16 ctrl = 0; 5781 bool found; 5782 struct pci_dev *bridge = bus->self; 5783 5784 pos = bridge->acs_cap; 5785 5786 /* Disable ACS SV before initial config reads */ 5787 if (pos) { 5788 pci_read_config_word(bridge, pos + PCI_ACS_CTRL, &ctrl); 5789 if (ctrl & PCI_ACS_SV) 5790 pci_write_config_word(bridge, pos + PCI_ACS_CTRL, 5791 ctrl & ~PCI_ACS_SV); 5792 } 5793 5794 found = pci_bus_generic_read_dev_vendor_id(bus, devfn, l, timeout); 5795 5796 /* Write Vendor ID (read-only) so the endpoint latches its bus/dev */ 5797 if (found) 5798 pci_bus_write_config_word(bus, devfn, PCI_VENDOR_ID, 0); 5799 5800 /* Re-enable ACS_SV if it was previously enabled */ 5801 if (ctrl & PCI_ACS_SV) 5802 pci_write_config_word(bridge, pos + PCI_ACS_CTRL, ctrl); 5803 5804 return found; 5805 } 5806 5807 /* 5808 * Microsemi Switchtec NTB uses devfn proxy IDs to move TLPs between 5809 * NT endpoints via the internal switch fabric. These IDs replace the 5810 * originating Requester ID TLPs which access host memory on peer NTB 5811 * ports. Therefore, all proxy IDs must be aliased to the NTB device 5812 * to permit access when the IOMMU is turned on. 5813 */ 5814 static void quirk_switchtec_ntb_dma_alias(struct pci_dev *pdev) 5815 { 5816 void __iomem *mmio; 5817 struct ntb_info_regs __iomem *mmio_ntb; 5818 struct ntb_ctrl_regs __iomem *mmio_ctrl; 5819 u64 partition_map; 5820 u8 partition; 5821 int pp; 5822 5823 if (pci_enable_device(pdev)) { 5824 pci_err(pdev, "Cannot enable Switchtec device\n"); 5825 return; 5826 } 5827 5828 mmio = pci_iomap(pdev, 0, 0); 5829 if (mmio == NULL) { 5830 pci_disable_device(pdev); 5831 pci_err(pdev, "Cannot iomap Switchtec device\n"); 5832 return; 5833 } 5834 5835 pci_info(pdev, "Setting Switchtec proxy ID aliases\n"); 5836 5837 mmio_ntb = mmio + SWITCHTEC_GAS_NTB_OFFSET; 5838 mmio_ctrl = (void __iomem *) mmio_ntb + SWITCHTEC_NTB_REG_CTRL_OFFSET; 5839 5840 partition = ioread8(&mmio_ntb->partition_id); 5841 5842 partition_map = ioread32(&mmio_ntb->ep_map); 5843 partition_map |= ((u64) ioread32(&mmio_ntb->ep_map + 4)) << 32; 5844 partition_map &= ~(1ULL << partition); 5845 5846 for (pp = 0; pp < (sizeof(partition_map) * 8); pp++) { 5847 struct ntb_ctrl_regs __iomem *mmio_peer_ctrl; 5848 u32 table_sz = 0; 5849 int te; 5850 5851 if (!(partition_map & (1ULL << pp))) 5852 continue; 5853 5854 pci_dbg(pdev, "Processing partition %d\n", pp); 5855 5856 mmio_peer_ctrl = &mmio_ctrl[pp]; 5857 5858 table_sz = ioread16(&mmio_peer_ctrl->req_id_table_size); 5859 if (!table_sz) { 5860 pci_warn(pdev, "Partition %d table_sz 0\n", pp); 5861 continue; 5862 } 5863 5864 if (table_sz > 512) { 5865 pci_warn(pdev, 5866 "Invalid Switchtec partition %d table_sz %d\n", 5867 pp, table_sz); 5868 continue; 5869 } 5870 5871 for (te = 0; te < table_sz; te++) { 5872 u32 rid_entry; 5873 u8 devfn; 5874 5875 rid_entry = ioread32(&mmio_peer_ctrl->req_id_table[te]); 5876 devfn = (rid_entry >> 1) & 0xFF; 5877 pci_dbg(pdev, 5878 "Aliasing Partition %d Proxy ID %02x.%d\n", 5879 pp, PCI_SLOT(devfn), PCI_FUNC(devfn)); 5880 pci_add_dma_alias(pdev, devfn, 1); 5881 } 5882 } 5883 5884 pci_iounmap(pdev, mmio); 5885 pci_disable_device(pdev); 5886 } 5887 #define SWITCHTEC_QUIRK(vid) \ 5888 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_MICROSEMI, vid, \ 5889 PCI_CLASS_BRIDGE_OTHER, 8, quirk_switchtec_ntb_dma_alias) 5890 5891 SWITCHTEC_QUIRK(0x8531); /* PFX 24xG3 */ 5892 SWITCHTEC_QUIRK(0x8532); /* PFX 32xG3 */ 5893 SWITCHTEC_QUIRK(0x8533); /* PFX 48xG3 */ 5894 SWITCHTEC_QUIRK(0x8534); /* PFX 64xG3 */ 5895 SWITCHTEC_QUIRK(0x8535); /* PFX 80xG3 */ 5896 SWITCHTEC_QUIRK(0x8536); /* PFX 96xG3 */ 5897 SWITCHTEC_QUIRK(0x8541); /* PSX 24xG3 */ 5898 SWITCHTEC_QUIRK(0x8542); /* PSX 32xG3 */ 5899 SWITCHTEC_QUIRK(0x8543); /* PSX 48xG3 */ 5900 SWITCHTEC_QUIRK(0x8544); /* PSX 64xG3 */ 5901 SWITCHTEC_QUIRK(0x8545); /* PSX 80xG3 */ 5902 SWITCHTEC_QUIRK(0x8546); /* PSX 96xG3 */ 5903 SWITCHTEC_QUIRK(0x8551); /* PAX 24XG3 */ 5904 SWITCHTEC_QUIRK(0x8552); /* PAX 32XG3 */ 5905 SWITCHTEC_QUIRK(0x8553); /* PAX 48XG3 */ 5906 SWITCHTEC_QUIRK(0x8554); /* PAX 64XG3 */ 5907 SWITCHTEC_QUIRK(0x8555); /* PAX 80XG3 */ 5908 SWITCHTEC_QUIRK(0x8556); /* PAX 96XG3 */ 5909 SWITCHTEC_QUIRK(0x8561); /* PFXL 24XG3 */ 5910 SWITCHTEC_QUIRK(0x8562); /* PFXL 32XG3 */ 5911 SWITCHTEC_QUIRK(0x8563); /* PFXL 48XG3 */ 5912 SWITCHTEC_QUIRK(0x8564); /* PFXL 64XG3 */ 5913 SWITCHTEC_QUIRK(0x8565); /* PFXL 80XG3 */ 5914 SWITCHTEC_QUIRK(0x8566); /* PFXL 96XG3 */ 5915 SWITCHTEC_QUIRK(0x8571); /* PFXI 24XG3 */ 5916 SWITCHTEC_QUIRK(0x8572); /* PFXI 32XG3 */ 5917 SWITCHTEC_QUIRK(0x8573); /* PFXI 48XG3 */ 5918 SWITCHTEC_QUIRK(0x8574); /* PFXI 64XG3 */ 5919 SWITCHTEC_QUIRK(0x8575); /* PFXI 80XG3 */ 5920 SWITCHTEC_QUIRK(0x8576); /* PFXI 96XG3 */ 5921 SWITCHTEC_QUIRK(0x4000); /* PFX 100XG4 */ 5922 SWITCHTEC_QUIRK(0x4084); /* PFX 84XG4 */ 5923 SWITCHTEC_QUIRK(0x4068); /* PFX 68XG4 */ 5924 SWITCHTEC_QUIRK(0x4052); /* PFX 52XG4 */ 5925 SWITCHTEC_QUIRK(0x4036); /* PFX 36XG4 */ 5926 SWITCHTEC_QUIRK(0x4028); /* PFX 28XG4 */ 5927 SWITCHTEC_QUIRK(0x4100); /* PSX 100XG4 */ 5928 SWITCHTEC_QUIRK(0x4184); /* PSX 84XG4 */ 5929 SWITCHTEC_QUIRK(0x4168); /* PSX 68XG4 */ 5930 SWITCHTEC_QUIRK(0x4152); /* PSX 52XG4 */ 5931 SWITCHTEC_QUIRK(0x4136); /* PSX 36XG4 */ 5932 SWITCHTEC_QUIRK(0x4128); /* PSX 28XG4 */ 5933 SWITCHTEC_QUIRK(0x4200); /* PAX 100XG4 */ 5934 SWITCHTEC_QUIRK(0x4284); /* PAX 84XG4 */ 5935 SWITCHTEC_QUIRK(0x4268); /* PAX 68XG4 */ 5936 SWITCHTEC_QUIRK(0x4252); /* PAX 52XG4 */ 5937 SWITCHTEC_QUIRK(0x4236); /* PAX 36XG4 */ 5938 SWITCHTEC_QUIRK(0x4228); /* PAX 28XG4 */ 5939 SWITCHTEC_QUIRK(0x4352); /* PFXA 52XG4 */ 5940 SWITCHTEC_QUIRK(0x4336); /* PFXA 36XG4 */ 5941 SWITCHTEC_QUIRK(0x4328); /* PFXA 28XG4 */ 5942 SWITCHTEC_QUIRK(0x4452); /* PSXA 52XG4 */ 5943 SWITCHTEC_QUIRK(0x4436); /* PSXA 36XG4 */ 5944 SWITCHTEC_QUIRK(0x4428); /* PSXA 28XG4 */ 5945 SWITCHTEC_QUIRK(0x4552); /* PAXA 52XG4 */ 5946 SWITCHTEC_QUIRK(0x4536); /* PAXA 36XG4 */ 5947 SWITCHTEC_QUIRK(0x4528); /* PAXA 28XG4 */ 5948 SWITCHTEC_QUIRK(0x5000); /* PFX 100XG5 */ 5949 SWITCHTEC_QUIRK(0x5084); /* PFX 84XG5 */ 5950 SWITCHTEC_QUIRK(0x5068); /* PFX 68XG5 */ 5951 SWITCHTEC_QUIRK(0x5052); /* PFX 52XG5 */ 5952 SWITCHTEC_QUIRK(0x5036); /* PFX 36XG5 */ 5953 SWITCHTEC_QUIRK(0x5028); /* PFX 28XG5 */ 5954 SWITCHTEC_QUIRK(0x5100); /* PSX 100XG5 */ 5955 SWITCHTEC_QUIRK(0x5184); /* PSX 84XG5 */ 5956 SWITCHTEC_QUIRK(0x5168); /* PSX 68XG5 */ 5957 SWITCHTEC_QUIRK(0x5152); /* PSX 52XG5 */ 5958 SWITCHTEC_QUIRK(0x5136); /* PSX 36XG5 */ 5959 SWITCHTEC_QUIRK(0x5128); /* PSX 28XG5 */ 5960 SWITCHTEC_QUIRK(0x5200); /* PAX 100XG5 */ 5961 SWITCHTEC_QUIRK(0x5284); /* PAX 84XG5 */ 5962 SWITCHTEC_QUIRK(0x5268); /* PAX 68XG5 */ 5963 SWITCHTEC_QUIRK(0x5252); /* PAX 52XG5 */ 5964 SWITCHTEC_QUIRK(0x5236); /* PAX 36XG5 */ 5965 SWITCHTEC_QUIRK(0x5228); /* PAX 28XG5 */ 5966 SWITCHTEC_QUIRK(0x5300); /* PFXA 100XG5 */ 5967 SWITCHTEC_QUIRK(0x5384); /* PFXA 84XG5 */ 5968 SWITCHTEC_QUIRK(0x5368); /* PFXA 68XG5 */ 5969 SWITCHTEC_QUIRK(0x5352); /* PFXA 52XG5 */ 5970 SWITCHTEC_QUIRK(0x5336); /* PFXA 36XG5 */ 5971 SWITCHTEC_QUIRK(0x5328); /* PFXA 28XG5 */ 5972 SWITCHTEC_QUIRK(0x5400); /* PSXA 100XG5 */ 5973 SWITCHTEC_QUIRK(0x5484); /* PSXA 84XG5 */ 5974 SWITCHTEC_QUIRK(0x5468); /* PSXA 68XG5 */ 5975 SWITCHTEC_QUIRK(0x5452); /* PSXA 52XG5 */ 5976 SWITCHTEC_QUIRK(0x5436); /* PSXA 36XG5 */ 5977 SWITCHTEC_QUIRK(0x5428); /* PSXA 28XG5 */ 5978 SWITCHTEC_QUIRK(0x5500); /* PAXA 100XG5 */ 5979 SWITCHTEC_QUIRK(0x5584); /* PAXA 84XG5 */ 5980 SWITCHTEC_QUIRK(0x5568); /* PAXA 68XG5 */ 5981 SWITCHTEC_QUIRK(0x5552); /* PAXA 52XG5 */ 5982 SWITCHTEC_QUIRK(0x5536); /* PAXA 36XG5 */ 5983 SWITCHTEC_QUIRK(0x5528); /* PAXA 28XG5 */ 5984 5985 /* 5986 * The PLX NTB uses devfn proxy IDs to move TLPs between NT endpoints. 5987 * These IDs are used to forward responses to the originator on the other 5988 * side of the NTB. Alias all possible IDs to the NTB to permit access when 5989 * the IOMMU is turned on. 5990 */ 5991 static void quirk_plx_ntb_dma_alias(struct pci_dev *pdev) 5992 { 5993 pci_info(pdev, "Setting PLX NTB proxy ID aliases\n"); 5994 /* PLX NTB may use all 256 devfns */ 5995 pci_add_dma_alias(pdev, 0, 256); 5996 } 5997 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_PLX, 0x87b0, quirk_plx_ntb_dma_alias); 5998 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_PLX, 0x87b1, quirk_plx_ntb_dma_alias); 5999 6000 /* 6001 * On Lenovo Thinkpad P50 SKUs with a Nvidia Quadro M1000M, the BIOS does 6002 * not always reset the secondary Nvidia GPU between reboots if the system 6003 * is configured to use Hybrid Graphics mode. This results in the GPU 6004 * being left in whatever state it was in during the *previous* boot, which 6005 * causes spurious interrupts from the GPU, which in turn causes us to 6006 * disable the wrong IRQ and end up breaking the touchpad. Unsurprisingly, 6007 * this also completely breaks nouveau. 6008 * 6009 * Luckily, it seems a simple reset of the Nvidia GPU brings it back to a 6010 * clean state and fixes all these issues. 6011 * 6012 * When the machine is configured in Dedicated display mode, the issue 6013 * doesn't occur. Fortunately the GPU advertises NoReset+ when in this 6014 * mode, so we can detect that and avoid resetting it. 6015 */ 6016 static void quirk_reset_lenovo_thinkpad_p50_nvgpu(struct pci_dev *pdev) 6017 { 6018 void __iomem *map; 6019 int ret; 6020 6021 if (pdev->subsystem_vendor != PCI_VENDOR_ID_LENOVO || 6022 pdev->subsystem_device != 0x222e || 6023 !pci_reset_supported(pdev)) 6024 return; 6025 6026 if (pci_enable_device_mem(pdev)) 6027 return; 6028 6029 /* 6030 * Based on nvkm_device_ctor() in 6031 * drivers/gpu/drm/nouveau/nvkm/engine/device/base.c 6032 */ 6033 map = pci_iomap(pdev, 0, 0x23000); 6034 if (!map) { 6035 pci_err(pdev, "Can't map MMIO space\n"); 6036 goto out_disable; 6037 } 6038 6039 /* 6040 * Make sure the GPU looks like it's been POSTed before resetting 6041 * it. 6042 */ 6043 if (ioread32(map + 0x2240c) & 0x2) { 6044 pci_info(pdev, FW_BUG "GPU left initialized by EFI, resetting\n"); 6045 ret = pci_reset_bus(pdev); 6046 if (ret < 0) 6047 pci_err(pdev, "Failed to reset GPU: %d\n", ret); 6048 } 6049 6050 iounmap(map); 6051 out_disable: 6052 pci_disable_device(pdev); 6053 } 6054 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_NVIDIA, 0x13b1, 6055 PCI_CLASS_DISPLAY_VGA, 8, 6056 quirk_reset_lenovo_thinkpad_p50_nvgpu); 6057 6058 /* 6059 * Device [1b21:2142] 6060 * When in D0, PME# doesn't get asserted when plugging USB 3.0 device. 6061 */ 6062 static void pci_fixup_no_d0_pme(struct pci_dev *dev) 6063 { 6064 pci_info(dev, "PME# does not work under D0, disabling it\n"); 6065 dev->pme_support &= ~(PCI_PM_CAP_PME_D0 >> PCI_PM_CAP_PME_SHIFT); 6066 } 6067 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ASMEDIA, 0x2142, pci_fixup_no_d0_pme); 6068 6069 /* 6070 * Device 12d8:0x400e [OHCI] and 12d8:0x400f [EHCI] 6071 * 6072 * These devices advertise PME# support in all power states but don't 6073 * reliably assert it. 6074 * 6075 * These devices also advertise MSI, but documentation (PI7C9X440SL.pdf) 6076 * says "The MSI Function is not implemented on this device" in chapters 6077 * 7.3.27, 7.3.29-7.3.31. 6078 */ 6079 static void pci_fixup_no_msi_no_pme(struct pci_dev *dev) 6080 { 6081 #ifdef CONFIG_PCI_MSI 6082 pci_info(dev, "MSI is not implemented on this device, disabling it\n"); 6083 dev->no_msi = 1; 6084 #endif 6085 pci_info(dev, "PME# is unreliable, disabling it\n"); 6086 dev->pme_support = 0; 6087 } 6088 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_PERICOM, 0x400e, pci_fixup_no_msi_no_pme); 6089 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_PERICOM, 0x400f, pci_fixup_no_msi_no_pme); 6090 6091 static void apex_pci_fixup_class(struct pci_dev *pdev) 6092 { 6093 pdev->class = (PCI_CLASS_SYSTEM_OTHER << 8) | pdev->class; 6094 } 6095 DECLARE_PCI_FIXUP_CLASS_HEADER(0x1ac1, 0x089a, 6096 PCI_CLASS_NOT_DEFINED, 8, apex_pci_fixup_class); 6097 6098 /* 6099 * Pericom PI7C9X2G404/PI7C9X2G304/PI7C9X2G303 switch erratum E5 - 6100 * ACS P2P Request Redirect is not functional 6101 * 6102 * When ACS P2P Request Redirect is enabled and bandwidth is not balanced 6103 * between upstream and downstream ports, packets are queued in an internal 6104 * buffer until CPLD packet. The workaround is to use the switch in store and 6105 * forward mode. 6106 */ 6107 #define PI7C9X2Gxxx_MODE_REG 0x74 6108 #define PI7C9X2Gxxx_STORE_FORWARD_MODE BIT(0) 6109 static void pci_fixup_pericom_acs_store_forward(struct pci_dev *pdev) 6110 { 6111 struct pci_dev *upstream; 6112 u16 val; 6113 6114 /* Downstream ports only */ 6115 if (pci_pcie_type(pdev) != PCI_EXP_TYPE_DOWNSTREAM) 6116 return; 6117 6118 /* Check for ACS P2P Request Redirect use */ 6119 if (!pdev->acs_cap) 6120 return; 6121 pci_read_config_word(pdev, pdev->acs_cap + PCI_ACS_CTRL, &val); 6122 if (!(val & PCI_ACS_RR)) 6123 return; 6124 6125 upstream = pci_upstream_bridge(pdev); 6126 if (!upstream) 6127 return; 6128 6129 pci_read_config_word(upstream, PI7C9X2Gxxx_MODE_REG, &val); 6130 if (!(val & PI7C9X2Gxxx_STORE_FORWARD_MODE)) { 6131 pci_info(upstream, "Setting PI7C9X2Gxxx store-forward mode to avoid ACS erratum\n"); 6132 pci_write_config_word(upstream, PI7C9X2Gxxx_MODE_REG, val | 6133 PI7C9X2Gxxx_STORE_FORWARD_MODE); 6134 } 6135 } 6136 /* 6137 * Apply fixup on enable and on resume, in order to apply the fix up whenever 6138 * ACS configuration changes or switch mode is reset 6139 */ 6140 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_PERICOM, 0x2404, 6141 pci_fixup_pericom_acs_store_forward); 6142 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_PERICOM, 0x2404, 6143 pci_fixup_pericom_acs_store_forward); 6144 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_PERICOM, 0x2304, 6145 pci_fixup_pericom_acs_store_forward); 6146 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_PERICOM, 0x2304, 6147 pci_fixup_pericom_acs_store_forward); 6148 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_PERICOM, 0x2303, 6149 pci_fixup_pericom_acs_store_forward); 6150 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_PERICOM, 0x2303, 6151 pci_fixup_pericom_acs_store_forward); 6152 6153 static void nvidia_ion_ahci_fixup(struct pci_dev *pdev) 6154 { 6155 pdev->dev_flags |= PCI_DEV_FLAGS_HAS_MSI_MASKING; 6156 } 6157 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, 0x0ab8, nvidia_ion_ahci_fixup); 6158 6159 static void rom_bar_overlap_defect(struct pci_dev *dev) 6160 { 6161 pci_info(dev, "working around ROM BAR overlap defect\n"); 6162 dev->rom_bar_overlap = 1; 6163 } 6164 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1533, rom_bar_overlap_defect); 6165 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1536, rom_bar_overlap_defect); 6166 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1537, rom_bar_overlap_defect); 6167 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1538, rom_bar_overlap_defect); 6168 6169 #ifdef CONFIG_PCIEASPM 6170 /* 6171 * Several Intel DG2 graphics devices advertise that they can only tolerate 6172 * 1us latency when transitioning from L1 to L0, which may prevent ASPM L1 6173 * from being enabled. But in fact these devices can tolerate unlimited 6174 * latency. Override their Device Capabilities value to allow ASPM L1 to 6175 * be enabled. 6176 */ 6177 static void aspm_l1_acceptable_latency(struct pci_dev *dev) 6178 { 6179 u32 l1_lat = FIELD_GET(PCI_EXP_DEVCAP_L1, dev->devcap); 6180 6181 if (l1_lat < 7) { 6182 dev->devcap |= FIELD_PREP(PCI_EXP_DEVCAP_L1, 7); 6183 pci_info(dev, "ASPM: overriding L1 acceptable latency from %#x to 0x7\n", 6184 l1_lat); 6185 } 6186 } 6187 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f80, aspm_l1_acceptable_latency); 6188 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f81, aspm_l1_acceptable_latency); 6189 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f82, aspm_l1_acceptable_latency); 6190 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f83, aspm_l1_acceptable_latency); 6191 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f84, aspm_l1_acceptable_latency); 6192 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f85, aspm_l1_acceptable_latency); 6193 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f86, aspm_l1_acceptable_latency); 6194 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f87, aspm_l1_acceptable_latency); 6195 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x4f88, aspm_l1_acceptable_latency); 6196 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5690, aspm_l1_acceptable_latency); 6197 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5691, aspm_l1_acceptable_latency); 6198 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5692, aspm_l1_acceptable_latency); 6199 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5693, aspm_l1_acceptable_latency); 6200 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5694, aspm_l1_acceptable_latency); 6201 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x5695, aspm_l1_acceptable_latency); 6202 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a0, aspm_l1_acceptable_latency); 6203 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a1, aspm_l1_acceptable_latency); 6204 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a2, aspm_l1_acceptable_latency); 6205 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a3, aspm_l1_acceptable_latency); 6206 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a4, aspm_l1_acceptable_latency); 6207 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a5, aspm_l1_acceptable_latency); 6208 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56a6, aspm_l1_acceptable_latency); 6209 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56b0, aspm_l1_acceptable_latency); 6210 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56b1, aspm_l1_acceptable_latency); 6211 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56c0, aspm_l1_acceptable_latency); 6212 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x56c1, aspm_l1_acceptable_latency); 6213 #endif 6214 6215 #ifdef CONFIG_PCIE_DPC 6216 /* 6217 * Intel Ice Lake, Tiger Lake and Alder Lake BIOS has a bug that clears 6218 * the DPC RP PIO Log Size of the integrated Thunderbolt PCIe Root 6219 * Ports. 6220 */ 6221 static void dpc_log_size(struct pci_dev *dev) 6222 { 6223 u16 dpc, val; 6224 6225 dpc = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_DPC); 6226 if (!dpc) 6227 return; 6228 6229 pci_read_config_word(dev, dpc + PCI_EXP_DPC_CAP, &val); 6230 if (!(val & PCI_EXP_DPC_CAP_RP_EXT)) 6231 return; 6232 6233 if (FIELD_GET(PCI_EXP_DPC_RP_PIO_LOG_SIZE, val) == 0) { 6234 pci_info(dev, "Overriding RP PIO Log Size to 4\n"); 6235 dev->dpc_rp_log_size = 4; 6236 } 6237 } 6238 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x461f, dpc_log_size); 6239 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x462f, dpc_log_size); 6240 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x463f, dpc_log_size); 6241 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x466e, dpc_log_size); 6242 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x8a1d, dpc_log_size); 6243 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x8a1f, dpc_log_size); 6244 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x8a21, dpc_log_size); 6245 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x8a23, dpc_log_size); 6246 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a23, dpc_log_size); 6247 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a25, dpc_log_size); 6248 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a27, dpc_log_size); 6249 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a29, dpc_log_size); 6250 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a2b, dpc_log_size); 6251 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a2d, dpc_log_size); 6252 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a2f, dpc_log_size); 6253 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x9a31, dpc_log_size); 6254 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0xa73f, dpc_log_size); 6255 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0xa76e, dpc_log_size); 6256 #endif 6257 6258 /* 6259 * For a PCI device with multiple downstream devices, its driver may use 6260 * a flattened device tree to describe the downstream devices. 6261 * To overlay the flattened device tree, the PCI device and all its ancestor 6262 * devices need to have device tree nodes on system base device tree. Thus, 6263 * before driver probing, it might need to add a device tree node as the final 6264 * fixup. 6265 */ 6266 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_XILINX, 0x5020, of_pci_make_dev_node); 6267 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_XILINX, 0x5021, of_pci_make_dev_node); 6268 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_REDHAT, 0x0005, of_pci_make_dev_node); 6269 6270 /* 6271 * Devices known to require a longer delay before first config space access 6272 * after reset recovery or resume from D3cold: 6273 * 6274 * VideoPropulsion (aka Genroco) Torrent QN16e MPEG QAM Modulator 6275 */ 6276 static void pci_fixup_d3cold_delay_1sec(struct pci_dev *pdev) 6277 { 6278 pdev->d3cold_delay = 1000; 6279 } 6280 DECLARE_PCI_FIXUP_FINAL(0x5555, 0x0004, pci_fixup_d3cold_delay_1sec); 6281 6282 #ifdef CONFIG_PCIEAER 6283 static void pci_mask_replay_timer_timeout(struct pci_dev *pdev) 6284 { 6285 struct pci_dev *parent = pci_upstream_bridge(pdev); 6286 u32 val; 6287 6288 if (!parent || !parent->aer_cap) 6289 return; 6290 6291 pci_info(parent, "mask Replay Timer Timeout Correctable Errors due to %s hardware defect", 6292 pci_name(pdev)); 6293 6294 pci_read_config_dword(parent, parent->aer_cap + PCI_ERR_COR_MASK, &val); 6295 val |= PCI_ERR_COR_REP_TIMER; 6296 pci_write_config_dword(parent, parent->aer_cap + PCI_ERR_COR_MASK, val); 6297 } 6298 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_GLI, 0x9750, pci_mask_replay_timer_timeout); 6299 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_GLI, 0x9755, pci_mask_replay_timer_timeout); 6300 #endif 6301