1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * i.MX6 OCOTP fusebox driver 4 * 5 * Copyright (c) 2015 Pengutronix, Philipp Zabel <p.zabel@pengutronix.de> 6 * 7 * Copyright 2019 NXP 8 * 9 * Based on the barebox ocotp driver, 10 * Copyright (c) 2010 Baruch Siach <baruch@tkos.co.il>, 11 * Orex Computed Radiography 12 * 13 * Write support based on the fsl_otp driver, 14 * Copyright (C) 2010-2013 Freescale Semiconductor, Inc 15 */ 16 17 #include <linux/clk.h> 18 #include <linux/device.h> 19 #include <linux/io.h> 20 #include <linux/module.h> 21 #include <linux/nvmem-provider.h> 22 #include <linux/of.h> 23 #include <linux/of_device.h> 24 #include <linux/platform_device.h> 25 #include <linux/slab.h> 26 #include <linux/delay.h> 27 28 #define IMX_OCOTP_OFFSET_B0W0 0x400 /* Offset from base address of the 29 * OTP Bank0 Word0 30 */ 31 #define IMX_OCOTP_OFFSET_PER_WORD 0x10 /* Offset between the start addr 32 * of two consecutive OTP words. 33 */ 34 35 #define IMX_OCOTP_ADDR_CTRL 0x0000 36 #define IMX_OCOTP_ADDR_CTRL_SET 0x0004 37 #define IMX_OCOTP_ADDR_CTRL_CLR 0x0008 38 #define IMX_OCOTP_ADDR_TIMING 0x0010 39 #define IMX_OCOTP_ADDR_DATA0 0x0020 40 #define IMX_OCOTP_ADDR_DATA1 0x0030 41 #define IMX_OCOTP_ADDR_DATA2 0x0040 42 #define IMX_OCOTP_ADDR_DATA3 0x0050 43 44 #define IMX_OCOTP_BM_CTRL_ADDR 0x000000FF 45 #define IMX_OCOTP_BM_CTRL_BUSY 0x00000100 46 #define IMX_OCOTP_BM_CTRL_ERROR 0x00000200 47 #define IMX_OCOTP_BM_CTRL_REL_SHADOWS 0x00000400 48 49 #define IMX_OCOTP_BM_CTRL_ADDR_8MP 0x000001FF 50 #define IMX_OCOTP_BM_CTRL_BUSY_8MP 0x00000200 51 #define IMX_OCOTP_BM_CTRL_ERROR_8MP 0x00000400 52 #define IMX_OCOTP_BM_CTRL_REL_SHADOWS_8MP 0x00000800 53 54 #define IMX_OCOTP_BM_CTRL_DEFAULT \ 55 { \ 56 .bm_addr = IMX_OCOTP_BM_CTRL_ADDR, \ 57 .bm_busy = IMX_OCOTP_BM_CTRL_BUSY, \ 58 .bm_error = IMX_OCOTP_BM_CTRL_ERROR, \ 59 .bm_rel_shadows = IMX_OCOTP_BM_CTRL_REL_SHADOWS,\ 60 } 61 62 #define IMX_OCOTP_BM_CTRL_8MP \ 63 { \ 64 .bm_addr = IMX_OCOTP_BM_CTRL_ADDR_8MP, \ 65 .bm_busy = IMX_OCOTP_BM_CTRL_BUSY_8MP, \ 66 .bm_error = IMX_OCOTP_BM_CTRL_ERROR_8MP, \ 67 .bm_rel_shadows = IMX_OCOTP_BM_CTRL_REL_SHADOWS_8MP,\ 68 } 69 70 #define TIMING_STROBE_PROG_US 10 /* Min time to blow a fuse */ 71 #define TIMING_STROBE_READ_NS 37 /* Min time before read */ 72 #define TIMING_RELAX_NS 17 73 #define DEF_FSOURCE 1001 /* > 1000 ns */ 74 #define DEF_STROBE_PROG 10000 /* IPG clocks */ 75 #define IMX_OCOTP_WR_UNLOCK 0x3E770000 76 #define IMX_OCOTP_READ_LOCKED_VAL 0xBADABADA 77 78 static DEFINE_MUTEX(ocotp_mutex); 79 80 struct ocotp_priv { 81 struct device *dev; 82 struct clk *clk; 83 void __iomem *base; 84 const struct ocotp_params *params; 85 struct nvmem_config *config; 86 }; 87 88 struct ocotp_ctrl_reg { 89 u32 bm_addr; 90 u32 bm_busy; 91 u32 bm_error; 92 u32 bm_rel_shadows; 93 }; 94 95 struct ocotp_params { 96 unsigned int nregs; 97 unsigned int bank_address_words; 98 void (*set_timing)(struct ocotp_priv *priv); 99 struct ocotp_ctrl_reg ctrl; 100 bool reverse_mac_address; 101 }; 102 103 static int imx_ocotp_wait_for_busy(struct ocotp_priv *priv, u32 flags) 104 { 105 int count; 106 u32 c, mask; 107 u32 bm_ctrl_busy, bm_ctrl_error; 108 void __iomem *base = priv->base; 109 110 bm_ctrl_busy = priv->params->ctrl.bm_busy; 111 bm_ctrl_error = priv->params->ctrl.bm_error; 112 113 mask = bm_ctrl_busy | bm_ctrl_error | flags; 114 115 for (count = 10000; count >= 0; count--) { 116 c = readl(base + IMX_OCOTP_ADDR_CTRL); 117 if (!(c & mask)) 118 break; 119 cpu_relax(); 120 } 121 122 if (count < 0) { 123 /* HW_OCOTP_CTRL[ERROR] will be set under the following 124 * conditions: 125 * - A write is performed to a shadow register during a shadow 126 * reload (essentially, while HW_OCOTP_CTRL[RELOAD_SHADOWS] is 127 * set. In addition, the contents of the shadow register shall 128 * not be updated. 129 * - A write is performed to a shadow register which has been 130 * locked. 131 * - A read is performed to from a shadow register which has 132 * been read locked. 133 * - A program is performed to a fuse word which has been locked 134 * - A read is performed to from a fuse word which has been read 135 * locked. 136 */ 137 if (c & bm_ctrl_error) 138 return -EPERM; 139 return -ETIMEDOUT; 140 } 141 142 return 0; 143 } 144 145 static void imx_ocotp_clr_err_if_set(struct ocotp_priv *priv) 146 { 147 u32 c, bm_ctrl_error; 148 void __iomem *base = priv->base; 149 150 bm_ctrl_error = priv->params->ctrl.bm_error; 151 152 c = readl(base + IMX_OCOTP_ADDR_CTRL); 153 if (!(c & bm_ctrl_error)) 154 return; 155 156 writel(bm_ctrl_error, base + IMX_OCOTP_ADDR_CTRL_CLR); 157 } 158 159 static int imx_ocotp_read(void *context, unsigned int offset, 160 void *val, size_t bytes) 161 { 162 struct ocotp_priv *priv = context; 163 unsigned int count; 164 u8 *buf, *p; 165 int i, ret; 166 u32 index, num_bytes; 167 168 index = offset >> 2; 169 num_bytes = round_up((offset % 4) + bytes, 4); 170 count = num_bytes >> 2; 171 172 if (count > (priv->params->nregs - index)) 173 count = priv->params->nregs - index; 174 175 p = kzalloc(num_bytes, GFP_KERNEL); 176 if (!p) 177 return -ENOMEM; 178 179 mutex_lock(&ocotp_mutex); 180 181 buf = p; 182 183 ret = clk_prepare_enable(priv->clk); 184 if (ret < 0) { 185 mutex_unlock(&ocotp_mutex); 186 dev_err(priv->dev, "failed to prepare/enable ocotp clk\n"); 187 kfree(p); 188 return ret; 189 } 190 191 ret = imx_ocotp_wait_for_busy(priv, 0); 192 if (ret < 0) { 193 dev_err(priv->dev, "timeout during read setup\n"); 194 goto read_end; 195 } 196 197 for (i = index; i < (index + count); i++) { 198 *(u32 *)buf = readl(priv->base + IMX_OCOTP_OFFSET_B0W0 + 199 i * IMX_OCOTP_OFFSET_PER_WORD); 200 201 /* 47.3.1.2 202 * For "read locked" registers 0xBADABADA will be returned and 203 * HW_OCOTP_CTRL[ERROR] will be set. It must be cleared by 204 * software before any new write, read or reload access can be 205 * issued 206 */ 207 if (*((u32 *)buf) == IMX_OCOTP_READ_LOCKED_VAL) 208 imx_ocotp_clr_err_if_set(priv); 209 210 buf += 4; 211 } 212 213 index = offset % 4; 214 memcpy(val, &p[index], bytes); 215 216 read_end: 217 clk_disable_unprepare(priv->clk); 218 mutex_unlock(&ocotp_mutex); 219 220 kfree(p); 221 222 return ret; 223 } 224 225 static int imx_ocotp_cell_pp(void *context, const char *id, int index, 226 unsigned int offset, void *data, size_t bytes) 227 { 228 struct ocotp_priv *priv = context; 229 230 /* Deal with some post processing of nvmem cell data */ 231 if (id && !strcmp(id, "mac-address")) { 232 if (priv->params->reverse_mac_address) { 233 u8 *buf = data; 234 int i; 235 236 for (i = 0; i < bytes/2; i++) 237 swap(buf[i], buf[bytes - i - 1]); 238 } 239 } 240 241 return 0; 242 } 243 244 static void imx_ocotp_set_imx6_timing(struct ocotp_priv *priv) 245 { 246 unsigned long clk_rate; 247 unsigned long strobe_read, relax, strobe_prog; 248 u32 timing; 249 250 /* 47.3.1.3.1 251 * Program HW_OCOTP_TIMING[STROBE_PROG] and HW_OCOTP_TIMING[RELAX] 252 * fields with timing values to match the current frequency of the 253 * ipg_clk. OTP writes will work at maximum bus frequencies as long 254 * as the HW_OCOTP_TIMING parameters are set correctly. 255 * 256 * Note: there are minimum timings required to ensure an OTP fuse burns 257 * correctly that are independent of the ipg_clk. Those values are not 258 * formally documented anywhere however, working from the minimum 259 * timings given in u-boot we can say: 260 * 261 * - Minimum STROBE_PROG time is 10 microseconds. Intuitively 10 262 * microseconds feels about right as representative of a minimum time 263 * to physically burn out a fuse. 264 * 265 * - Minimum STROBE_READ i.e. the time to wait post OTP fuse burn before 266 * performing another read is 37 nanoseconds 267 * 268 * - Minimum RELAX timing is 17 nanoseconds. This final RELAX minimum 269 * timing is not entirely clear the documentation says "This 270 * count value specifies the time to add to all default timing 271 * parameters other than the Tpgm and Trd. It is given in number 272 * of ipg_clk periods." where Tpgm and Trd refer to STROBE_PROG 273 * and STROBE_READ respectively. What the other timing parameters 274 * are though, is not specified. Experience shows a zero RELAX 275 * value will mess up a re-load of the shadow registers post OTP 276 * burn. 277 */ 278 clk_rate = clk_get_rate(priv->clk); 279 280 relax = DIV_ROUND_UP(clk_rate * TIMING_RELAX_NS, 1000000000) - 1; 281 strobe_read = DIV_ROUND_UP(clk_rate * TIMING_STROBE_READ_NS, 282 1000000000); 283 strobe_read += 2 * (relax + 1) - 1; 284 strobe_prog = DIV_ROUND_CLOSEST(clk_rate * TIMING_STROBE_PROG_US, 285 1000000); 286 strobe_prog += 2 * (relax + 1) - 1; 287 288 timing = readl(priv->base + IMX_OCOTP_ADDR_TIMING) & 0x0FC00000; 289 timing |= strobe_prog & 0x00000FFF; 290 timing |= (relax << 12) & 0x0000F000; 291 timing |= (strobe_read << 16) & 0x003F0000; 292 293 writel(timing, priv->base + IMX_OCOTP_ADDR_TIMING); 294 } 295 296 static void imx_ocotp_set_imx7_timing(struct ocotp_priv *priv) 297 { 298 unsigned long clk_rate; 299 u64 fsource, strobe_prog; 300 u32 timing; 301 302 /* i.MX 7Solo Applications Processor Reference Manual, Rev. 0.1 303 * 6.4.3.3 304 */ 305 clk_rate = clk_get_rate(priv->clk); 306 fsource = DIV_ROUND_UP_ULL((u64)clk_rate * DEF_FSOURCE, 307 NSEC_PER_SEC) + 1; 308 strobe_prog = DIV_ROUND_CLOSEST_ULL((u64)clk_rate * DEF_STROBE_PROG, 309 NSEC_PER_SEC) + 1; 310 311 timing = strobe_prog & 0x00000FFF; 312 timing |= (fsource << 12) & 0x000FF000; 313 314 writel(timing, priv->base + IMX_OCOTP_ADDR_TIMING); 315 } 316 317 static int imx_ocotp_write(void *context, unsigned int offset, void *val, 318 size_t bytes) 319 { 320 struct ocotp_priv *priv = context; 321 u32 *buf = val; 322 int ret; 323 324 u32 ctrl; 325 u8 waddr; 326 u8 word = 0; 327 328 /* allow only writing one complete OTP word at a time */ 329 if ((bytes != priv->config->word_size) || 330 (offset % priv->config->word_size)) 331 return -EINVAL; 332 333 mutex_lock(&ocotp_mutex); 334 335 ret = clk_prepare_enable(priv->clk); 336 if (ret < 0) { 337 mutex_unlock(&ocotp_mutex); 338 dev_err(priv->dev, "failed to prepare/enable ocotp clk\n"); 339 return ret; 340 } 341 342 /* Setup the write timing values */ 343 priv->params->set_timing(priv); 344 345 /* 47.3.1.3.2 346 * Check that HW_OCOTP_CTRL[BUSY] and HW_OCOTP_CTRL[ERROR] are clear. 347 * Overlapped accesses are not supported by the controller. Any pending 348 * write or reload must be completed before a write access can be 349 * requested. 350 */ 351 ret = imx_ocotp_wait_for_busy(priv, 0); 352 if (ret < 0) { 353 dev_err(priv->dev, "timeout during timing setup\n"); 354 goto write_end; 355 } 356 357 /* 47.3.1.3.3 358 * Write the requested address to HW_OCOTP_CTRL[ADDR] and program the 359 * unlock code into HW_OCOTP_CTRL[WR_UNLOCK]. This must be programmed 360 * for each write access. The lock code is documented in the register 361 * description. Both the unlock code and address can be written in the 362 * same operation. 363 */ 364 if (priv->params->bank_address_words != 0) { 365 /* 366 * In banked/i.MX7 mode the OTP register bank goes into waddr 367 * see i.MX 7Solo Applications Processor Reference Manual, Rev. 368 * 0.1 section 6.4.3.1 369 */ 370 offset = offset / priv->config->word_size; 371 waddr = offset / priv->params->bank_address_words; 372 word = offset & (priv->params->bank_address_words - 1); 373 } else { 374 /* 375 * Non-banked i.MX6 mode. 376 * OTP write/read address specifies one of 128 word address 377 * locations 378 */ 379 waddr = offset / 4; 380 } 381 382 ctrl = readl(priv->base + IMX_OCOTP_ADDR_CTRL); 383 ctrl &= ~priv->params->ctrl.bm_addr; 384 ctrl |= waddr & priv->params->ctrl.bm_addr; 385 ctrl |= IMX_OCOTP_WR_UNLOCK; 386 387 writel(ctrl, priv->base + IMX_OCOTP_ADDR_CTRL); 388 389 /* 47.3.1.3.4 390 * Write the data to the HW_OCOTP_DATA register. This will automatically 391 * set HW_OCOTP_CTRL[BUSY] and clear HW_OCOTP_CTRL[WR_UNLOCK]. To 392 * protect programming same OTP bit twice, before program OCOTP will 393 * automatically read fuse value in OTP and use read value to mask 394 * program data. The controller will use masked program data to program 395 * a 32-bit word in the OTP per the address in HW_OCOTP_CTRL[ADDR]. Bit 396 * fields with 1's will result in that OTP bit being programmed. Bit 397 * fields with 0's will be ignored. At the same time that the write is 398 * accepted, the controller makes an internal copy of 399 * HW_OCOTP_CTRL[ADDR] which cannot be updated until the next write 400 * sequence is initiated. This copy guarantees that erroneous writes to 401 * HW_OCOTP_CTRL[ADDR] will not affect an active write operation. It 402 * should also be noted that during the programming HW_OCOTP_DATA will 403 * shift right (with zero fill). This shifting is required to program 404 * the OTP serially. During the write operation, HW_OCOTP_DATA cannot be 405 * modified. 406 * Note: on i.MX7 there are four data fields to write for banked write 407 * with the fuse blowing operation only taking place after data0 408 * has been written. This is why data0 must always be the last 409 * register written. 410 */ 411 if (priv->params->bank_address_words != 0) { 412 /* Banked/i.MX7 mode */ 413 switch (word) { 414 case 0: 415 writel(0, priv->base + IMX_OCOTP_ADDR_DATA1); 416 writel(0, priv->base + IMX_OCOTP_ADDR_DATA2); 417 writel(0, priv->base + IMX_OCOTP_ADDR_DATA3); 418 writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA0); 419 break; 420 case 1: 421 writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA1); 422 writel(0, priv->base + IMX_OCOTP_ADDR_DATA2); 423 writel(0, priv->base + IMX_OCOTP_ADDR_DATA3); 424 writel(0, priv->base + IMX_OCOTP_ADDR_DATA0); 425 break; 426 case 2: 427 writel(0, priv->base + IMX_OCOTP_ADDR_DATA1); 428 writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA2); 429 writel(0, priv->base + IMX_OCOTP_ADDR_DATA3); 430 writel(0, priv->base + IMX_OCOTP_ADDR_DATA0); 431 break; 432 case 3: 433 writel(0, priv->base + IMX_OCOTP_ADDR_DATA1); 434 writel(0, priv->base + IMX_OCOTP_ADDR_DATA2); 435 writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA3); 436 writel(0, priv->base + IMX_OCOTP_ADDR_DATA0); 437 break; 438 } 439 } else { 440 /* Non-banked i.MX6 mode */ 441 writel(*buf, priv->base + IMX_OCOTP_ADDR_DATA0); 442 } 443 444 /* 47.4.1.4.5 445 * Once complete, the controller will clear BUSY. A write request to a 446 * protected or locked region will result in no OTP access and no 447 * setting of HW_OCOTP_CTRL[BUSY]. In addition HW_OCOTP_CTRL[ERROR] will 448 * be set. It must be cleared by software before any new write access 449 * can be issued. 450 */ 451 ret = imx_ocotp_wait_for_busy(priv, 0); 452 if (ret < 0) { 453 if (ret == -EPERM) { 454 dev_err(priv->dev, "failed write to locked region"); 455 imx_ocotp_clr_err_if_set(priv); 456 } else { 457 dev_err(priv->dev, "timeout during data write\n"); 458 } 459 goto write_end; 460 } 461 462 /* 47.3.1.4 463 * Write Postamble: Due to internal electrical characteristics of the 464 * OTP during writes, all OTP operations following a write must be 465 * separated by 2 us after the clearing of HW_OCOTP_CTRL_BUSY following 466 * the write. 467 */ 468 udelay(2); 469 470 /* reload all shadow registers */ 471 writel(priv->params->ctrl.bm_rel_shadows, 472 priv->base + IMX_OCOTP_ADDR_CTRL_SET); 473 ret = imx_ocotp_wait_for_busy(priv, 474 priv->params->ctrl.bm_rel_shadows); 475 if (ret < 0) 476 dev_err(priv->dev, "timeout during shadow register reload\n"); 477 478 write_end: 479 clk_disable_unprepare(priv->clk); 480 mutex_unlock(&ocotp_mutex); 481 return ret < 0 ? ret : bytes; 482 } 483 484 static struct nvmem_config imx_ocotp_nvmem_config = { 485 .name = "imx-ocotp", 486 .read_only = false, 487 .word_size = 4, 488 .stride = 1, 489 .reg_read = imx_ocotp_read, 490 .reg_write = imx_ocotp_write, 491 .cell_post_process = imx_ocotp_cell_pp, 492 }; 493 494 static const struct ocotp_params imx6q_params = { 495 .nregs = 128, 496 .bank_address_words = 0, 497 .set_timing = imx_ocotp_set_imx6_timing, 498 .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT, 499 }; 500 501 static const struct ocotp_params imx6sl_params = { 502 .nregs = 64, 503 .bank_address_words = 0, 504 .set_timing = imx_ocotp_set_imx6_timing, 505 .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT, 506 }; 507 508 static const struct ocotp_params imx6sll_params = { 509 .nregs = 128, 510 .bank_address_words = 0, 511 .set_timing = imx_ocotp_set_imx6_timing, 512 .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT, 513 }; 514 515 static const struct ocotp_params imx6sx_params = { 516 .nregs = 128, 517 .bank_address_words = 0, 518 .set_timing = imx_ocotp_set_imx6_timing, 519 .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT, 520 }; 521 522 static const struct ocotp_params imx6ul_params = { 523 .nregs = 128, 524 .bank_address_words = 0, 525 .set_timing = imx_ocotp_set_imx6_timing, 526 .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT, 527 }; 528 529 static const struct ocotp_params imx6ull_params = { 530 .nregs = 64, 531 .bank_address_words = 0, 532 .set_timing = imx_ocotp_set_imx6_timing, 533 .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT, 534 }; 535 536 static const struct ocotp_params imx7d_params = { 537 .nregs = 64, 538 .bank_address_words = 4, 539 .set_timing = imx_ocotp_set_imx7_timing, 540 .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT, 541 }; 542 543 static const struct ocotp_params imx7ulp_params = { 544 .nregs = 256, 545 .bank_address_words = 0, 546 .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT, 547 }; 548 549 static const struct ocotp_params imx8mq_params = { 550 .nregs = 256, 551 .bank_address_words = 0, 552 .set_timing = imx_ocotp_set_imx6_timing, 553 .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT, 554 .reverse_mac_address = true, 555 }; 556 557 static const struct ocotp_params imx8mm_params = { 558 .nregs = 256, 559 .bank_address_words = 0, 560 .set_timing = imx_ocotp_set_imx6_timing, 561 .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT, 562 .reverse_mac_address = true, 563 }; 564 565 static const struct ocotp_params imx8mn_params = { 566 .nregs = 256, 567 .bank_address_words = 0, 568 .set_timing = imx_ocotp_set_imx6_timing, 569 .ctrl = IMX_OCOTP_BM_CTRL_DEFAULT, 570 .reverse_mac_address = true, 571 }; 572 573 static const struct ocotp_params imx8mp_params = { 574 .nregs = 384, 575 .bank_address_words = 0, 576 .set_timing = imx_ocotp_set_imx6_timing, 577 .ctrl = IMX_OCOTP_BM_CTRL_8MP, 578 .reverse_mac_address = true, 579 }; 580 581 static const struct of_device_id imx_ocotp_dt_ids[] = { 582 { .compatible = "fsl,imx6q-ocotp", .data = &imx6q_params }, 583 { .compatible = "fsl,imx6sl-ocotp", .data = &imx6sl_params }, 584 { .compatible = "fsl,imx6sx-ocotp", .data = &imx6sx_params }, 585 { .compatible = "fsl,imx6ul-ocotp", .data = &imx6ul_params }, 586 { .compatible = "fsl,imx6ull-ocotp", .data = &imx6ull_params }, 587 { .compatible = "fsl,imx7d-ocotp", .data = &imx7d_params }, 588 { .compatible = "fsl,imx6sll-ocotp", .data = &imx6sll_params }, 589 { .compatible = "fsl,imx7ulp-ocotp", .data = &imx7ulp_params }, 590 { .compatible = "fsl,imx8mq-ocotp", .data = &imx8mq_params }, 591 { .compatible = "fsl,imx8mm-ocotp", .data = &imx8mm_params }, 592 { .compatible = "fsl,imx8mn-ocotp", .data = &imx8mn_params }, 593 { .compatible = "fsl,imx8mp-ocotp", .data = &imx8mp_params }, 594 { }, 595 }; 596 MODULE_DEVICE_TABLE(of, imx_ocotp_dt_ids); 597 598 static int imx_ocotp_probe(struct platform_device *pdev) 599 { 600 struct device *dev = &pdev->dev; 601 struct ocotp_priv *priv; 602 struct nvmem_device *nvmem; 603 604 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); 605 if (!priv) 606 return -ENOMEM; 607 608 priv->dev = dev; 609 610 priv->base = devm_platform_ioremap_resource(pdev, 0); 611 if (IS_ERR(priv->base)) 612 return PTR_ERR(priv->base); 613 614 priv->clk = devm_clk_get(dev, NULL); 615 if (IS_ERR(priv->clk)) 616 return PTR_ERR(priv->clk); 617 618 priv->params = of_device_get_match_data(&pdev->dev); 619 imx_ocotp_nvmem_config.size = 4 * priv->params->nregs; 620 imx_ocotp_nvmem_config.dev = dev; 621 imx_ocotp_nvmem_config.priv = priv; 622 priv->config = &imx_ocotp_nvmem_config; 623 624 clk_prepare_enable(priv->clk); 625 imx_ocotp_clr_err_if_set(priv); 626 clk_disable_unprepare(priv->clk); 627 628 nvmem = devm_nvmem_register(dev, &imx_ocotp_nvmem_config); 629 630 return PTR_ERR_OR_ZERO(nvmem); 631 } 632 633 static struct platform_driver imx_ocotp_driver = { 634 .probe = imx_ocotp_probe, 635 .driver = { 636 .name = "imx_ocotp", 637 .of_match_table = imx_ocotp_dt_ids, 638 }, 639 }; 640 module_platform_driver(imx_ocotp_driver); 641 642 MODULE_AUTHOR("Philipp Zabel <p.zabel@pengutronix.de>"); 643 MODULE_DESCRIPTION("i.MX6/i.MX7 OCOTP fuse box driver"); 644 MODULE_LICENSE("GPL v2"); 645