1 // SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause 2 /* 3 * Copyright (C) 2017 Intel Deutschland GmbH 4 * Copyright (C) 2018-2021 Intel Corporation 5 */ 6 #include "iwl-trans.h" 7 #include "iwl-prph.h" 8 #include "iwl-context-info.h" 9 #include "iwl-context-info-gen3.h" 10 #include "internal.h" 11 #include "fw/dbg.h" 12 13 #define FW_RESET_TIMEOUT (HZ / 5) 14 15 /* 16 * Start up NIC's basic functionality after it has been reset 17 * (e.g. after platform boot, or shutdown via iwl_pcie_apm_stop()) 18 * NOTE: This does not load uCode nor start the embedded processor 19 */ 20 int iwl_pcie_gen2_apm_init(struct iwl_trans *trans) 21 { 22 int ret = 0; 23 24 IWL_DEBUG_INFO(trans, "Init card's basic functions\n"); 25 26 /* 27 * Use "set_bit" below rather than "write", to preserve any hardware 28 * bits already set by default after reset. 29 */ 30 31 /* 32 * Disable L0s without affecting L1; 33 * don't wait for ICH L0s (ICH bug W/A) 34 */ 35 iwl_set_bit(trans, CSR_GIO_CHICKEN_BITS, 36 CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX); 37 38 /* Set FH wait threshold to maximum (HW error during stress W/A) */ 39 iwl_set_bit(trans, CSR_DBG_HPET_MEM_REG, CSR_DBG_HPET_MEM_REG_VAL); 40 41 /* 42 * Enable HAP INTA (interrupt from management bus) to 43 * wake device's PCI Express link L1a -> L0s 44 */ 45 iwl_set_bit(trans, CSR_HW_IF_CONFIG_REG, 46 CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A); 47 48 iwl_pcie_apm_config(trans); 49 50 ret = iwl_finish_nic_init(trans); 51 if (ret) 52 return ret; 53 54 set_bit(STATUS_DEVICE_ENABLED, &trans->status); 55 56 return 0; 57 } 58 59 static void iwl_pcie_gen2_apm_stop(struct iwl_trans *trans, bool op_mode_leave) 60 { 61 IWL_DEBUG_INFO(trans, "Stop card, put in low power state\n"); 62 63 if (op_mode_leave) { 64 if (!test_bit(STATUS_DEVICE_ENABLED, &trans->status)) 65 iwl_pcie_gen2_apm_init(trans); 66 67 /* inform ME that we are leaving */ 68 iwl_set_bit(trans, CSR_DBG_LINK_PWR_MGMT_REG, 69 CSR_RESET_LINK_PWR_MGMT_DISABLED); 70 iwl_set_bit(trans, CSR_HW_IF_CONFIG_REG, 71 CSR_HW_IF_CONFIG_REG_PREPARE | 72 CSR_HW_IF_CONFIG_REG_ENABLE_PME); 73 mdelay(1); 74 iwl_clear_bit(trans, CSR_DBG_LINK_PWR_MGMT_REG, 75 CSR_RESET_LINK_PWR_MGMT_DISABLED); 76 mdelay(5); 77 } 78 79 clear_bit(STATUS_DEVICE_ENABLED, &trans->status); 80 81 /* Stop device's DMA activity */ 82 iwl_pcie_apm_stop_master(trans); 83 84 iwl_trans_sw_reset(trans, false); 85 86 /* 87 * Clear "initialization complete" bit to move adapter from 88 * D0A* (powered-up Active) --> D0U* (Uninitialized) state. 89 */ 90 if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_BZ) 91 iwl_clear_bit(trans, CSR_GP_CNTRL, 92 CSR_GP_CNTRL_REG_FLAG_MAC_INIT); 93 else 94 iwl_clear_bit(trans, CSR_GP_CNTRL, 95 CSR_GP_CNTRL_REG_FLAG_INIT_DONE); 96 } 97 98 static void iwl_trans_pcie_fw_reset_handshake(struct iwl_trans *trans) 99 { 100 struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); 101 int ret; 102 103 trans_pcie->fw_reset_state = FW_RESET_REQUESTED; 104 105 if (trans->trans_cfg->device_family < IWL_DEVICE_FAMILY_AX210) 106 iwl_write_umac_prph(trans, UREG_NIC_SET_NMI_DRIVER, 107 UREG_NIC_SET_NMI_DRIVER_RESET_HANDSHAKE); 108 else if (trans->trans_cfg->device_family == IWL_DEVICE_FAMILY_AX210) 109 iwl_write_umac_prph(trans, UREG_DOORBELL_TO_ISR6, 110 UREG_DOORBELL_TO_ISR6_RESET_HANDSHAKE); 111 else 112 iwl_write32(trans, CSR_DOORBELL_VECTOR, 113 UREG_DOORBELL_TO_ISR6_RESET_HANDSHAKE); 114 115 /* wait 200ms */ 116 ret = wait_event_timeout(trans_pcie->fw_reset_waitq, 117 trans_pcie->fw_reset_state != FW_RESET_REQUESTED, 118 FW_RESET_TIMEOUT); 119 if (!ret || trans_pcie->fw_reset_state == FW_RESET_ERROR) { 120 IWL_INFO(trans, 121 "firmware didn't ACK the reset - continue anyway\n"); 122 iwl_trans_fw_error(trans, true); 123 } 124 125 trans_pcie->fw_reset_state = FW_RESET_IDLE; 126 } 127 128 void _iwl_trans_pcie_gen2_stop_device(struct iwl_trans *trans) 129 { 130 struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); 131 132 lockdep_assert_held(&trans_pcie->mutex); 133 134 if (trans_pcie->is_down) 135 return; 136 137 if (trans->state >= IWL_TRANS_FW_STARTED) 138 if (trans_pcie->fw_reset_handshake) 139 iwl_trans_pcie_fw_reset_handshake(trans); 140 141 trans_pcie->is_down = true; 142 143 /* tell the device to stop sending interrupts */ 144 iwl_disable_interrupts(trans); 145 146 /* device going down, Stop using ICT table */ 147 iwl_pcie_disable_ict(trans); 148 149 /* 150 * If a HW restart happens during firmware loading, 151 * then the firmware loading might call this function 152 * and later it might be called again due to the 153 * restart. So don't process again if the device is 154 * already dead. 155 */ 156 if (test_and_clear_bit(STATUS_DEVICE_ENABLED, &trans->status)) { 157 IWL_DEBUG_INFO(trans, 158 "DEVICE_ENABLED bit was set and is now cleared\n"); 159 iwl_txq_gen2_tx_free(trans); 160 iwl_pcie_rx_stop(trans); 161 } 162 163 iwl_pcie_ctxt_info_free_paging(trans); 164 if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_AX210) 165 iwl_pcie_ctxt_info_gen3_free(trans, false); 166 else 167 iwl_pcie_ctxt_info_free(trans); 168 169 /* Stop the device, and put it in low power state */ 170 iwl_pcie_gen2_apm_stop(trans, false); 171 172 /* re-take ownership to prevent other users from stealing the device */ 173 iwl_trans_sw_reset(trans, true); 174 175 /* 176 * Upon stop, the IVAR table gets erased, so msi-x won't 177 * work. This causes a bug in RF-KILL flows, since the interrupt 178 * that enables radio won't fire on the correct irq, and the 179 * driver won't be able to handle the interrupt. 180 * Configure the IVAR table again after reset. 181 */ 182 iwl_pcie_conf_msix_hw(trans_pcie); 183 184 /* 185 * Upon stop, the APM issues an interrupt if HW RF kill is set. 186 * This is a bug in certain verions of the hardware. 187 * Certain devices also keep sending HW RF kill interrupt all 188 * the time, unless the interrupt is ACKed even if the interrupt 189 * should be masked. Re-ACK all the interrupts here. 190 */ 191 iwl_disable_interrupts(trans); 192 193 /* clear all status bits */ 194 clear_bit(STATUS_SYNC_HCMD_ACTIVE, &trans->status); 195 clear_bit(STATUS_INT_ENABLED, &trans->status); 196 clear_bit(STATUS_TPOWER_PMI, &trans->status); 197 198 /* 199 * Even if we stop the HW, we still want the RF kill 200 * interrupt 201 */ 202 iwl_enable_rfkill_int(trans); 203 } 204 205 void iwl_trans_pcie_gen2_stop_device(struct iwl_trans *trans) 206 { 207 struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); 208 bool was_in_rfkill; 209 210 iwl_op_mode_time_point(trans->op_mode, 211 IWL_FW_INI_TIME_POINT_HOST_DEVICE_DISABLE, 212 NULL); 213 214 mutex_lock(&trans_pcie->mutex); 215 trans_pcie->opmode_down = true; 216 was_in_rfkill = test_bit(STATUS_RFKILL_OPMODE, &trans->status); 217 _iwl_trans_pcie_gen2_stop_device(trans); 218 iwl_trans_pcie_handle_stop_rfkill(trans, was_in_rfkill); 219 mutex_unlock(&trans_pcie->mutex); 220 } 221 222 static int iwl_pcie_gen2_nic_init(struct iwl_trans *trans) 223 { 224 struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); 225 int queue_size = max_t(u32, IWL_CMD_QUEUE_SIZE, 226 trans->cfg->min_txq_size); 227 228 /* TODO: most of the logic can be removed in A0 - but not in Z0 */ 229 spin_lock_bh(&trans_pcie->irq_lock); 230 iwl_pcie_gen2_apm_init(trans); 231 spin_unlock_bh(&trans_pcie->irq_lock); 232 233 iwl_op_mode_nic_config(trans->op_mode); 234 235 /* Allocate the RX queue, or reset if it is already allocated */ 236 if (iwl_pcie_gen2_rx_init(trans)) 237 return -ENOMEM; 238 239 /* Allocate or reset and init all Tx and Command queues */ 240 if (iwl_txq_gen2_init(trans, trans->txqs.cmd.q_id, queue_size)) 241 return -ENOMEM; 242 243 /* enable shadow regs in HW */ 244 iwl_set_bit(trans, CSR_MAC_SHADOW_REG_CTRL, 0x800FFFFF); 245 IWL_DEBUG_INFO(trans, "Enabling shadow registers in device\n"); 246 247 return 0; 248 } 249 250 static void iwl_pcie_get_rf_name(struct iwl_trans *trans) 251 { 252 struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); 253 char *buf = trans_pcie->rf_name; 254 size_t buflen = sizeof(trans_pcie->rf_name); 255 size_t pos; 256 u32 version; 257 258 if (buf[0]) 259 return; 260 261 switch (CSR_HW_RFID_TYPE(trans->hw_rf_id)) { 262 case CSR_HW_RFID_TYPE(CSR_HW_RF_ID_TYPE_JF): 263 pos = scnprintf(buf, buflen, "JF"); 264 break; 265 case CSR_HW_RFID_TYPE(CSR_HW_RF_ID_TYPE_GF): 266 pos = scnprintf(buf, buflen, "GF"); 267 break; 268 case CSR_HW_RFID_TYPE(CSR_HW_RF_ID_TYPE_GF4): 269 pos = scnprintf(buf, buflen, "GF4"); 270 break; 271 case CSR_HW_RFID_TYPE(CSR_HW_RF_ID_TYPE_HR): 272 pos = scnprintf(buf, buflen, "HR"); 273 break; 274 case CSR_HW_RFID_TYPE(CSR_HW_RF_ID_TYPE_HR1): 275 pos = scnprintf(buf, buflen, "HR1"); 276 break; 277 case CSR_HW_RFID_TYPE(CSR_HW_RF_ID_TYPE_HRCDB): 278 pos = scnprintf(buf, buflen, "HRCDB"); 279 break; 280 default: 281 return; 282 } 283 284 switch (CSR_HW_RFID_TYPE(trans->hw_rf_id)) { 285 case CSR_HW_RFID_TYPE(CSR_HW_RF_ID_TYPE_HR): 286 case CSR_HW_RFID_TYPE(CSR_HW_RF_ID_TYPE_HR1): 287 case CSR_HW_RFID_TYPE(CSR_HW_RF_ID_TYPE_HRCDB): 288 version = iwl_read_prph(trans, CNVI_MBOX_C); 289 switch (version) { 290 case 0x20000: 291 pos += scnprintf(buf + pos, buflen - pos, " B3"); 292 break; 293 case 0x120000: 294 pos += scnprintf(buf + pos, buflen - pos, " B5"); 295 break; 296 default: 297 pos += scnprintf(buf + pos, buflen - pos, 298 " (0x%x)", version); 299 break; 300 } 301 break; 302 default: 303 break; 304 } 305 306 pos += scnprintf(buf + pos, buflen - pos, ", rfid=0x%x", 307 trans->hw_rf_id); 308 309 IWL_INFO(trans, "Detected RF %s\n", buf); 310 311 /* 312 * also add a \n for debugfs - need to do it after printing 313 * since our IWL_INFO machinery wants to see a static \n at 314 * the end of the string 315 */ 316 pos += scnprintf(buf + pos, buflen - pos, "\n"); 317 } 318 319 void iwl_trans_pcie_gen2_fw_alive(struct iwl_trans *trans, u32 scd_addr) 320 { 321 struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); 322 323 iwl_pcie_reset_ict(trans); 324 325 /* make sure all queue are not stopped/used */ 326 memset(trans->txqs.queue_stopped, 0, 327 sizeof(trans->txqs.queue_stopped)); 328 memset(trans->txqs.queue_used, 0, sizeof(trans->txqs.queue_used)); 329 330 /* now that we got alive we can free the fw image & the context info. 331 * paging memory cannot be freed included since FW will still use it 332 */ 333 if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_AX210) 334 iwl_pcie_ctxt_info_gen3_free(trans, true); 335 else 336 iwl_pcie_ctxt_info_free(trans); 337 338 /* 339 * Re-enable all the interrupts, including the RF-Kill one, now that 340 * the firmware is alive. 341 */ 342 iwl_enable_interrupts(trans); 343 mutex_lock(&trans_pcie->mutex); 344 iwl_pcie_check_hw_rf_kill(trans); 345 346 iwl_pcie_get_rf_name(trans); 347 mutex_unlock(&trans_pcie->mutex); 348 } 349 350 static void iwl_pcie_set_ltr(struct iwl_trans *trans) 351 { 352 u32 ltr_val = CSR_LTR_LONG_VAL_AD_NO_SNOOP_REQ | 353 u32_encode_bits(CSR_LTR_LONG_VAL_AD_SCALE_USEC, 354 CSR_LTR_LONG_VAL_AD_NO_SNOOP_SCALE) | 355 u32_encode_bits(250, 356 CSR_LTR_LONG_VAL_AD_NO_SNOOP_VAL) | 357 CSR_LTR_LONG_VAL_AD_SNOOP_REQ | 358 u32_encode_bits(CSR_LTR_LONG_VAL_AD_SCALE_USEC, 359 CSR_LTR_LONG_VAL_AD_SNOOP_SCALE) | 360 u32_encode_bits(250, CSR_LTR_LONG_VAL_AD_SNOOP_VAL); 361 362 /* 363 * To workaround hardware latency issues during the boot process, 364 * initialize the LTR to ~250 usec (see ltr_val above). 365 * The firmware initializes this again later (to a smaller value). 366 */ 367 if ((trans->trans_cfg->device_family == IWL_DEVICE_FAMILY_AX210 || 368 trans->trans_cfg->device_family == IWL_DEVICE_FAMILY_22000) && 369 !trans->trans_cfg->integrated) { 370 iwl_write32(trans, CSR_LTR_LONG_VAL_AD, ltr_val); 371 } else if (trans->trans_cfg->integrated && 372 trans->trans_cfg->device_family == IWL_DEVICE_FAMILY_22000) { 373 iwl_write_prph(trans, HPM_MAC_LTR_CSR, HPM_MAC_LRT_ENABLE_ALL); 374 iwl_write_prph(trans, HPM_UMAC_LTR, ltr_val); 375 } 376 } 377 378 int iwl_trans_pcie_gen2_start_fw(struct iwl_trans *trans, 379 const struct fw_img *fw, bool run_in_rfkill) 380 { 381 struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); 382 bool hw_rfkill; 383 int ret; 384 385 /* This may fail if AMT took ownership of the device */ 386 if (iwl_pcie_prepare_card_hw(trans)) { 387 IWL_WARN(trans, "Exit HW not ready\n"); 388 return -EIO; 389 } 390 391 iwl_enable_rfkill_int(trans); 392 393 iwl_write32(trans, CSR_INT, 0xFFFFFFFF); 394 395 /* 396 * We enabled the RF-Kill interrupt and the handler may very 397 * well be running. Disable the interrupts to make sure no other 398 * interrupt can be fired. 399 */ 400 iwl_disable_interrupts(trans); 401 402 /* Make sure it finished running */ 403 iwl_pcie_synchronize_irqs(trans); 404 405 mutex_lock(&trans_pcie->mutex); 406 407 /* If platform's RF_KILL switch is NOT set to KILL */ 408 hw_rfkill = iwl_pcie_check_hw_rf_kill(trans); 409 if (hw_rfkill && !run_in_rfkill) { 410 ret = -ERFKILL; 411 goto out; 412 } 413 414 /* Someone called stop_device, don't try to start_fw */ 415 if (trans_pcie->is_down) { 416 IWL_WARN(trans, 417 "Can't start_fw since the HW hasn't been started\n"); 418 ret = -EIO; 419 goto out; 420 } 421 422 /* make sure rfkill handshake bits are cleared */ 423 iwl_write32(trans, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL); 424 iwl_write32(trans, CSR_UCODE_DRV_GP1_CLR, 425 CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED); 426 427 /* clear (again), then enable host interrupts */ 428 iwl_write32(trans, CSR_INT, 0xFFFFFFFF); 429 430 ret = iwl_pcie_gen2_nic_init(trans); 431 if (ret) { 432 IWL_ERR(trans, "Unable to init nic\n"); 433 goto out; 434 } 435 436 if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_AX210) 437 ret = iwl_pcie_ctxt_info_gen3_init(trans, fw); 438 else 439 ret = iwl_pcie_ctxt_info_init(trans, fw); 440 if (ret) 441 goto out; 442 443 iwl_pcie_set_ltr(trans); 444 445 if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_BZ) { 446 iwl_write32(trans, CSR_FUNC_SCRATCH, CSR_FUNC_SCRATCH_INIT_VALUE); 447 iwl_set_bit(trans, CSR_GP_CNTRL, 448 CSR_GP_CNTRL_REG_FLAG_ROM_START); 449 } else if (trans->trans_cfg->device_family >= IWL_DEVICE_FAMILY_AX210) { 450 iwl_write_umac_prph(trans, UREG_CPU_INIT_RUN, 1); 451 } else { 452 iwl_write_prph(trans, UREG_CPU_INIT_RUN, 1); 453 } 454 455 /* re-check RF-Kill state since we may have missed the interrupt */ 456 hw_rfkill = iwl_pcie_check_hw_rf_kill(trans); 457 if (hw_rfkill && !run_in_rfkill) 458 ret = -ERFKILL; 459 460 out: 461 mutex_unlock(&trans_pcie->mutex); 462 return ret; 463 } 464