1 /* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */ 2 /* 3 * Copyright (C) 2005-2014, 2018-2025 Intel Corporation 4 * Copyright (C) 2013-2014 Intel Mobile Communications GmbH 5 * Copyright (C) 2016 Intel Deutschland GmbH 6 */ 7 #ifndef __iwl_csr_h__ 8 #define __iwl_csr_h__ 9 /* 10 * CSR (control and status registers) 11 * 12 * CSR registers are mapped directly into PCI bus space, and are accessible 13 * whenever platform supplies power to device, even when device is in 14 * low power states due to driver-invoked device resets 15 * (e.g. CSR_RESET_REG_FLAG_SW_RESET) or uCode-driven power-saving modes. 16 * 17 * Use iwl_write32() and iwl_read32() family to access these registers; 18 * these provide simple PCI bus access, without waking up the MAC. 19 * Do not use iwl_write_direct32() family for these registers; 20 * no need to "grab nic access" via CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ. 21 * The MAC (uCode processor, etc.) does not need to be powered up for accessing 22 * the CSR registers. 23 * 24 * NOTE: Device does need to be awake in order to read this memory 25 * via CSR_EEPROM and CSR_OTP registers 26 */ 27 #define CSR_BASE (0x000) 28 29 #define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */ 30 #define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */ 31 #define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */ 32 #define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */ 33 #define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/ 34 #define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */ 35 #define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/ 36 #define CSR_GP_CNTRL (CSR_BASE+0x024) 37 #define CSR_FUNC_SCRATCH (CSR_BASE+0x02c) /* Scratch register - used for FW dbg */ 38 39 /* 2nd byte of CSR_INT_COALESCING, not accessible via iwl_write32()! */ 40 #define CSR_INT_PERIODIC_REG (CSR_BASE+0x005) 41 42 /* 43 * Hardware revision info 44 * Bit fields: 45 * 31-16: Reserved 46 * 15-4: Type of device: see CSR_HW_REV_TYPE_xxx definitions 47 * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D 48 * 1-0: "Dash" (-) value, as in A-1, etc. 49 */ 50 #define CSR_HW_REV (CSR_BASE+0x028) 51 52 /* 53 * RF ID revision info 54 * Bit fields: 55 * 31:24: Reserved (set to 0x0) 56 * 23:12: Type 57 * 11:8: Step (A - 0x0, B - 0x1, etc) 58 * 7:4: Dash 59 * 3:0: Flavor 60 */ 61 #define CSR_HW_RF_ID (CSR_BASE+0x09c) 62 63 /* 64 * EEPROM and OTP (one-time-programmable) memory reads 65 * 66 * NOTE: Device must be awake, initialized via apm_ops.init(), 67 * in order to read. 68 */ 69 #define CSR_EEPROM_REG (CSR_BASE+0x02c) 70 #define CSR_EEPROM_GP (CSR_BASE+0x030) 71 #define CSR_OTP_GP_REG (CSR_BASE+0x034) 72 73 #define CSR_GIO_REG (CSR_BASE+0x03C) 74 #define CSR_GP_UCODE_REG (CSR_BASE+0x048) 75 #define CSR_GP_DRIVER_REG (CSR_BASE+0x050) 76 77 /* 78 * UCODE-DRIVER GP (general purpose) mailbox registers. 79 * SET/CLR registers set/clear bit(s) if "1" is written. 80 */ 81 #define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054) 82 #define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058) 83 #define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c) 84 #define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060) 85 86 #define CSR_MBOX_SET_REG (CSR_BASE + 0x88) 87 88 #define CSR_LED_REG (CSR_BASE+0x094) 89 #define CSR_DRAM_INT_TBL_REG (CSR_BASE+0x0A0) 90 #define CSR_MAC_SHADOW_REG_CTRL (CSR_BASE + 0x0A8) /* 6000 and up */ 91 #define CSR_MAC_SHADOW_REG_CTRL_RX_WAKE BIT(20) 92 #define CSR_MAC_SHADOW_REG_CTL2 (CSR_BASE + 0x0AC) 93 #define CSR_MAC_SHADOW_REG_CTL2_RX_WAKE 0xFFFF 94 95 /* LTR control (since IWL_DEVICE_FAMILY_22000) */ 96 #define CSR_LTR_LONG_VAL_AD (CSR_BASE + 0x0D4) 97 #define CSR_LTR_LONG_VAL_AD_NO_SNOOP_REQ 0x80000000 98 #define CSR_LTR_LONG_VAL_AD_NO_SNOOP_SCALE 0x1c000000 99 #define CSR_LTR_LONG_VAL_AD_NO_SNOOP_VAL 0x03ff0000 100 #define CSR_LTR_LONG_VAL_AD_SNOOP_REQ 0x00008000 101 #define CSR_LTR_LONG_VAL_AD_SNOOP_SCALE 0x00001c00 102 #define CSR_LTR_LONG_VAL_AD_SNOOP_VAL 0x000003ff 103 #define CSR_LTR_LONG_VAL_AD_SCALE_USEC 2 104 105 #define CSR_LTR_LAST_MSG (CSR_BASE + 0x0DC) 106 107 /* GIO Chicken Bits (PCI Express bus link power management) */ 108 #define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100) 109 110 #define CSR_IPC_STATE (CSR_BASE + 0x110) 111 #define CSR_IPC_STATE_RESET 0x00000030 112 #define CSR_IPC_STATE_RESET_NONE 0 113 #define CSR_IPC_STATE_RESET_SW_READY 1 114 #define CSR_IPC_STATE_RESET_TOP_READY 2 115 #define CSR_IPC_STATE_RESET_TOP_FOLLOWER 3 116 117 #define CSR_IPC_SLEEP_CONTROL (CSR_BASE + 0x114) 118 #define CSR_IPC_SLEEP_CONTROL_SUSPEND 0x3 119 #define CSR_IPC_SLEEP_CONTROL_RESUME 0 120 121 /* Doorbell - since Bz 122 * connected to UREG_DOORBELL_TO_ISR6 (lower 16 bits only) 123 */ 124 #define CSR_DOORBELL_VECTOR (CSR_BASE + 0x130) 125 126 /* host chicken bits */ 127 #define CSR_HOST_CHICKEN (CSR_BASE + 0x204) 128 #define CSR_HOST_CHICKEN_PM_IDLE_SRC_DIS_SB_PME BIT(19) 129 130 /* Analog phase-lock-loop configuration */ 131 #define CSR_ANA_PLL_CFG (CSR_BASE+0x20c) 132 133 /* 134 * CSR HW resources monitor registers 135 */ 136 #define CSR_MONITOR_CFG_REG (CSR_BASE+0x214) 137 #define CSR_MONITOR_STATUS_REG (CSR_BASE+0x228) 138 #define CSR_MONITOR_XTAL_RESOURCES (0x00000010) 139 140 /* 141 * CSR Hardware Revision Workaround Register. Indicates hardware rev; 142 * "step" determines CCK backoff for txpower calculation. 143 * See also CSR_HW_REV register. 144 * Bit fields: 145 * 3-2: 0 = A, 1 = B, 2 = C, 3 = D step 146 * 1-0: "Dash" (-) value, as in C-1, etc. 147 */ 148 #define CSR_HW_REV_WA_REG (CSR_BASE+0x22C) 149 150 #define CSR_DBG_HPET_MEM_REG (CSR_BASE+0x240) 151 #define CSR_DBG_LINK_PWR_MGMT_REG (CSR_BASE+0x250) 152 153 /* 154 * Scratch register initial configuration - this is set on init, and read 155 * during a error FW error. 156 */ 157 #define CSR_FUNC_SCRATCH_INIT_VALUE (0x01010101) 158 159 /* Bits for CSR_HW_IF_CONFIG_REG */ 160 #define CSR_HW_IF_CONFIG_REG_MSK_MAC_STEP_DASH (0x0000000F) 161 #define CSR_HW_IF_CONFIG_REG_BIT_MONITOR_SRAM (0x00000080) 162 #define CSR_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x000000C0) 163 #define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100) 164 #define CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200) 165 #define CSR_HW_IF_CONFIG_REG_D3_DEBUG (0x00000200) 166 #define CSR_HW_IF_CONFIG_REG_MSK_PHY_TYPE (0x00000C00) 167 #define CSR_HW_IF_CONFIG_REG_MSK_PHY_DASH (0x00003000) 168 #define CSR_HW_IF_CONFIG_REG_MSK_PHY_STEP (0x0000C000) 169 170 #define CSR_HW_IF_CONFIG_REG_POS_MAC_DASH (0) 171 #define CSR_HW_IF_CONFIG_REG_POS_MAC_STEP (2) 172 #define CSR_HW_IF_CONFIG_REG_POS_BOARD_VER (6) 173 #define CSR_HW_IF_CONFIG_REG_POS_PHY_TYPE (10) 174 #define CSR_HW_IF_CONFIG_REG_POS_PHY_DASH (12) 175 #define CSR_HW_IF_CONFIG_REG_POS_PHY_STEP (14) 176 177 #define CSR_HW_IF_CONFIG_REG_HAP_WAKE 0x00080000 178 /* NOTE: EEPROM_OWN_SEM is no longer defined for new HW */ 179 #define CSR_HW_IF_CONFIG_REG_EEPROM_OWN_SEM 0x00200000 180 #define CSR_HW_IF_CONFIG_REG_PCI_OWN_SET 0x00400000 181 #define CSR_HW_IF_CONFIG_REG_IAMT_UP 0x01000000 182 #define CSR_HW_IF_CONFIG_REG_ME_OWN 0x02000000 183 #define CSR_HW_IF_CONFIG_REG_WAKE_ME 0x08000000 184 #define CSR_HW_IF_CONFIG_REG_WAKE_ME_PCIE_OWNER_EN 0x10000000 185 #define CSR_HW_IF_CONFIG_REG_PERSISTENCE 0x40000000 186 187 #define CSR_MBOX_SET_REG_OS_ALIVE BIT(5) 188 189 #define CSR_INT_PERIODIC_DIS (0x00) /* disable periodic int*/ 190 #define CSR_INT_PERIODIC_ENA (0xFF) /* 255*32 usec ~ 8 msec*/ 191 192 /* interrupt flags in INTA, set by uCode or hardware (e.g. dma), 193 * acknowledged (reset) by host writing "1" to flagged bits. */ 194 #define CSR_INT_BIT_FH_RX (1 << 31) /* Rx DMA, cmd responses, FH_INT[17:16] */ 195 #define CSR_INT_BIT_HW_ERR (1 << 29) /* DMA hardware error FH_INT[31] */ 196 #define CSR_INT_BIT_RX_PERIODIC (1 << 28) /* Rx periodic */ 197 #define CSR_INT_BIT_FH_TX (1 << 27) /* Tx DMA FH_INT[1:0] */ 198 #define CSR_INT_BIT_SCD (1 << 26) /* TXQ pointer advanced */ 199 #define CSR_INT_BIT_SW_ERR (1 << 25) /* uCode error */ 200 #define CSR_INT_BIT_RF_KILL (1 << 7) /* HW RFKILL switch GP_CNTRL[27] toggled */ 201 #define CSR_INT_BIT_CT_KILL (1 << 6) /* Critical temp (chip too hot) rfkill */ 202 #define CSR_INT_BIT_SW_RX (1 << 3) /* Rx, command responses */ 203 #define CSR_INT_BIT_RESET_DONE (1 << 2) /* reset handshake with firmware is done */ 204 #define CSR_INT_BIT_WAKEUP (1 << 1) /* NIC controller waking up (pwr mgmt) */ 205 #define CSR_INT_BIT_ALIVE (1 << 0) /* uCode interrupts once it initializes */ 206 207 #define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \ 208 CSR_INT_BIT_HW_ERR | \ 209 CSR_INT_BIT_FH_TX | \ 210 CSR_INT_BIT_SW_ERR | \ 211 CSR_INT_BIT_RF_KILL | \ 212 CSR_INT_BIT_SW_RX | \ 213 CSR_INT_BIT_WAKEUP | \ 214 CSR_INT_BIT_RESET_DONE | \ 215 CSR_INT_BIT_ALIVE | \ 216 CSR_INT_BIT_RX_PERIODIC) 217 218 /* interrupt flags in FH (flow handler) (PCI busmaster DMA) */ 219 #define CSR_FH_INT_BIT_ERR (1 << 31) /* Error */ 220 #define CSR_FH_INT_BIT_HI_PRIOR (1 << 30) /* High priority Rx, bypass coalescing */ 221 #define CSR_FH_INT_BIT_RX_CHNL1 (1 << 17) /* Rx channel 1 */ 222 #define CSR_FH_INT_BIT_RX_CHNL0 (1 << 16) /* Rx channel 0 */ 223 #define CSR_FH_INT_BIT_TX_CHNL1 (1 << 1) /* Tx channel 1 */ 224 #define CSR_FH_INT_BIT_TX_CHNL0 (1 << 0) /* Tx channel 0 */ 225 226 #define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \ 227 CSR_FH_INT_BIT_RX_CHNL1 | \ 228 CSR_FH_INT_BIT_RX_CHNL0) 229 230 #define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \ 231 CSR_FH_INT_BIT_TX_CHNL0) 232 233 /* GPIO */ 234 #define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200) 235 #define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000) 236 #define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC (0x00000200) 237 238 /* RESET */ 239 #define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001) 240 #define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002) 241 #define CSR_RESET_REG_FLAG_SW_RESET (0x00000080) 242 #define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100) 243 #define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200) 244 #define CSR_RESET_LINK_PWR_MGMT_DISABLED (0x80000000) 245 246 /* 247 * GP (general purpose) CONTROL REGISTER 248 * Bit fields: 249 * 27: HW_RF_KILL_SW 250 * Indicates state of (platform's) hardware RF-Kill switch 251 * 26-24: POWER_SAVE_TYPE 252 * Indicates current power-saving mode: 253 * 000 -- No power saving 254 * 001 -- MAC power-down 255 * 010 -- PHY (radio) power-down 256 * 011 -- Error 257 * 10: XTAL ON request 258 * 9-6: SYS_CONFIG 259 * Indicates current system configuration, reflecting pins on chip 260 * as forced high/low by device circuit board. 261 * 4: GOING_TO_SLEEP 262 * Indicates MAC is entering a power-saving sleep power-down. 263 * Not a good time to access device-internal resources. 264 * 3: MAC_ACCESS_REQ 265 * Host sets this to request and maintain MAC wakeup, to allow host 266 * access to device-internal resources. Host must wait for 267 * MAC_CLOCK_READY (and !GOING_TO_SLEEP) before accessing non-CSR 268 * device registers. 269 * 2: INIT_DONE 270 * Host sets this to put device into fully operational D0 power mode. 271 * Host resets this after SW_RESET to put device into low power mode. 272 * 0: MAC_CLOCK_READY 273 * Indicates MAC (ucode processor, etc.) is powered up and can run. 274 * Internal resources are accessible. 275 * NOTE: This does not indicate that the processor is actually running. 276 * NOTE: This does not indicate that device has completed 277 * init or post-power-down restore of internal SRAM memory. 278 * Use CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP as indication that 279 * SRAM is restored and uCode is in normal operation mode. 280 * Later devices (5xxx/6xxx/1xxx) use non-volatile SRAM, and 281 * do not need to save/restore it. 282 * NOTE: After device reset, this bit remains "0" until host sets 283 * INIT_DONE 284 */ 285 #define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001) 286 #define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004) 287 #define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008) 288 #define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010) 289 #define CSR_GP_CNTRL_REG_FLAG_XTAL_ON (0x00000400) 290 291 #define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001) 292 293 #define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000) 294 #define CSR_GP_CNTRL_REG_FLAG_RFKILL_WAKE_L1A_EN (0x04000000) 295 #define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000) 296 297 /* From Bz we use these instead during init/reset flow */ 298 #define CSR_GP_CNTRL_REG_FLAG_MAC_INIT BIT(6) 299 #define CSR_GP_CNTRL_REG_FLAG_ROM_START BIT(7) 300 #define CSR_GP_CNTRL_REG_FLAG_MAC_STATUS BIT(20) 301 #define CSR_GP_CNTRL_REG_FLAG_BZ_MAC_ACCESS_REQ BIT(21) 302 #define CSR_GP_CNTRL_REG_FLAG_BUS_MASTER_DISABLE_STATUS BIT(28) 303 #define CSR_GP_CNTRL_REG_FLAG_BUS_MASTER_DISABLE_REQ BIT(29) 304 #define CSR_GP_CNTRL_REG_FLAG_SW_RESET BIT(31) 305 306 /* HW REV */ 307 #define CSR_HW_REV_STEP_DASH(_val) ((_val) & CSR_HW_IF_CONFIG_REG_MSK_MAC_STEP_DASH) 308 #define CSR_HW_REV_TYPE(_val) (((_val) & 0x000FFF0) >> 4) 309 310 /* HW RFID */ 311 #define CSR_HW_RFID_FLAVOR(_val) (((_val) & 0x000000F) >> 0) 312 #define CSR_HW_RFID_DASH(_val) (((_val) & 0x00000F0) >> 4) 313 #define CSR_HW_RFID_STEP(_val) (((_val) & 0x0000F00) >> 8) 314 #define CSR_HW_RFID_TYPE(_val) (((_val) & 0x0FFF000) >> 12) 315 #define CSR_HW_RFID_IS_CDB(_val) (((_val) & 0x10000000) >> 28) 316 #define CSR_HW_RFID_IS_JACKET(_val) (((_val) & 0x20000000) >> 29) 317 318 /* hw_rev values */ 319 enum { 320 SILICON_A_STEP = 0, 321 SILICON_B_STEP, 322 SILICON_C_STEP, 323 SILICON_D_STEP, 324 SILICON_E_STEP, 325 SILICON_TC_STEP = 0xe, 326 SILICON_Z_STEP = 0xf, 327 }; 328 329 330 #define CSR_HW_REV_TYPE_MSK (0x000FFF0) 331 #define CSR_HW_REV_TYPE_5300 (0x0000020) 332 #define CSR_HW_REV_TYPE_5350 (0x0000030) 333 #define CSR_HW_REV_TYPE_5100 (0x0000050) 334 #define CSR_HW_REV_TYPE_5150 (0x0000040) 335 #define CSR_HW_REV_TYPE_1000 (0x0000060) 336 #define CSR_HW_REV_TYPE_6x00 (0x0000070) 337 #define CSR_HW_REV_TYPE_6x50 (0x0000080) 338 #define CSR_HW_REV_TYPE_6150 (0x0000084) 339 #define CSR_HW_REV_TYPE_6x05 (0x00000B0) 340 #define CSR_HW_REV_TYPE_6x30 CSR_HW_REV_TYPE_6x05 341 #define CSR_HW_REV_TYPE_6x35 CSR_HW_REV_TYPE_6x05 342 #define CSR_HW_REV_TYPE_2x30 (0x00000C0) 343 #define CSR_HW_REV_TYPE_2x00 (0x0000100) 344 #define CSR_HW_REV_TYPE_105 (0x0000110) 345 #define CSR_HW_REV_TYPE_135 (0x0000120) 346 #define CSR_HW_REV_TYPE_3160 (0x0000164) 347 #define CSR_HW_REV_TYPE_7265D (0x0000210) 348 #define CSR_HW_REV_TYPE_NONE (0x00001F0) 349 #define CSR_HW_REV_TYPE_QNJ (0x0000360) 350 #define CSR_HW_REV_TYPE_QNJ_B0 (0x0000361) 351 #define CSR_HW_REV_TYPE_QU_B0 (0x0000331) 352 #define CSR_HW_REV_TYPE_QU_C0 (0x0000332) 353 #define CSR_HW_REV_TYPE_QUZ (0x0000351) 354 #define CSR_HW_REV_TYPE_HR_CDB (0x0000340) 355 #define CSR_HW_REV_TYPE_SO (0x0000370) 356 #define CSR_HW_REV_TYPE_TY (0x0000420) 357 358 /* RF_ID value */ 359 #define CSR_HW_RF_ID_TYPE_JF (0x00105100) 360 #define CSR_HW_RF_ID_TYPE_HR (0x0010A000) 361 #define CSR_HW_RF_ID_TYPE_HR1 (0x0010c100) 362 #define CSR_HW_RF_ID_TYPE_HRCDB (0x00109F00) 363 #define CSR_HW_RF_ID_TYPE_GF (0x0010D000) 364 #define CSR_HW_RF_ID_TYPE_GF4 (0x0010E000) 365 #define CSR_HW_RF_ID_TYPE_FM (0x00112000) 366 #define CSR_HW_RF_ID_TYPE_WP (0x00113000) 367 368 /* HW_RF CHIP STEP */ 369 #define CSR_HW_RF_STEP(_val) (((_val) >> 8) & 0xF) 370 371 /* EEPROM REG */ 372 #define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001) 373 #define CSR_EEPROM_REG_BIT_CMD (0x00000002) 374 #define CSR_EEPROM_REG_MSK_ADDR (0x0000FFFC) 375 #define CSR_EEPROM_REG_MSK_DATA (0xFFFF0000) 376 377 /* EEPROM GP */ 378 #define CSR_EEPROM_GP_VALID_MSK (0x00000007) /* signature */ 379 #define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180) 380 #define CSR_EEPROM_GP_BAD_SIGNATURE_BOTH_EEP_AND_OTP (0x00000000) 381 #define CSR_EEPROM_GP_BAD_SIG_EEP_GOOD_SIG_OTP (0x00000001) 382 #define CSR_EEPROM_GP_GOOD_SIG_EEP_LESS_THAN_4K (0x00000002) 383 #define CSR_EEPROM_GP_GOOD_SIG_EEP_MORE_THAN_4K (0x00000004) 384 385 /* One-time-programmable memory general purpose reg */ 386 #define CSR_OTP_GP_REG_DEVICE_SELECT (0x00010000) /* 0 - EEPROM, 1 - OTP */ 387 #define CSR_OTP_GP_REG_OTP_ACCESS_MODE (0x00020000) /* 0 - absolute, 1 - relative */ 388 #define CSR_OTP_GP_REG_ECC_CORR_STATUS_MSK (0x00100000) /* bit 20 */ 389 #define CSR_OTP_GP_REG_ECC_UNCORR_STATUS_MSK (0x00200000) /* bit 21 */ 390 391 /* GP REG */ 392 #define CSR_GP_REG_POWER_SAVE_STATUS_MSK (0x03000000) /* bit 24/25 */ 393 #define CSR_GP_REG_NO_POWER_SAVE (0x00000000) 394 #define CSR_GP_REG_MAC_POWER_SAVE (0x01000000) 395 #define CSR_GP_REG_PHY_POWER_SAVE (0x02000000) 396 #define CSR_GP_REG_POWER_SAVE_ERROR (0x03000000) 397 398 399 /* CSR GIO */ 400 #define CSR_GIO_REG_VAL_L0S_DISABLED (0x00000002) 401 402 /* 403 * UCODE-DRIVER GP (general purpose) mailbox register 1 404 * Host driver and uCode write and/or read this register to communicate with 405 * each other. 406 * Bit fields: 407 * 4: UCODE_DISABLE 408 * Host sets this to request permanent halt of uCode, same as 409 * sending CARD_STATE command with "halt" bit set. 410 * 3: CT_KILL_EXIT 411 * Host sets this to request exit from CT_KILL state, i.e. host thinks 412 * device temperature is low enough to continue normal operation. 413 * 2: CMD_BLOCKED 414 * Host sets this during RF KILL power-down sequence (HW, SW, CT KILL) 415 * to release uCode to clear all Tx and command queues, enter 416 * unassociated mode, and power down. 417 * NOTE: Some devices also use HBUS_TARG_MBX_C register for this bit. 418 * 1: SW_BIT_RFKILL 419 * Host sets this when issuing CARD_STATE command to request 420 * device sleep. 421 * 0: MAC_SLEEP 422 * uCode sets this when preparing a power-saving power-down. 423 * uCode resets this when power-up is complete and SRAM is sane. 424 * NOTE: device saves internal SRAM data to host when powering down, 425 * and must restore this data after powering back up. 426 * MAC_SLEEP is the best indication that restore is complete. 427 * Later devices (5xxx/6xxx/1xxx) use non-volatile SRAM, and 428 * do not need to save/restore it. 429 */ 430 #define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001) 431 #define CSR_UCODE_SW_BIT_RFKILL (0x00000002) 432 #define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004) 433 #define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008) 434 #define CSR_UCODE_DRV_GP1_BIT_D3_CFG_COMPLETE (0x00000020) 435 436 /* GP Driver */ 437 #define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_MSK (0x00000003) 438 #define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_3x3_HYB (0x00000000) 439 #define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_2x2_HYB (0x00000001) 440 #define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_2x2_IPA (0x00000002) 441 #define CSR_GP_DRIVER_REG_BIT_CALIB_VERSION6 (0x00000004) 442 #define CSR_GP_DRIVER_REG_BIT_6050_1x2 (0x00000008) 443 444 #define CSR_GP_DRIVER_REG_BIT_RADIO_IQ_INVER (0x00000080) 445 446 /* GIO Chicken Bits (PCI Express bus link power management) */ 447 #define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000) 448 #define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000) 449 450 /* LED */ 451 #define CSR_LED_BSM_CTRL_MSK (0xFFFFFFDF) 452 #define CSR_LED_REG_TURN_ON (0x60) 453 #define CSR_LED_REG_TURN_OFF (0x20) 454 455 /* ANA_PLL */ 456 #define CSR50_ANA_PLL_CFG_VAL (0x00880300) 457 458 /* HPET MEM debug */ 459 #define CSR_DBG_HPET_MEM_REG_VAL (0xFFFF0000) 460 461 /* DRAM INT TABLE */ 462 #define CSR_DRAM_INT_TBL_ENABLE (1 << 31) 463 #define CSR_DRAM_INIT_TBL_WRITE_POINTER (1 << 28) 464 #define CSR_DRAM_INIT_TBL_WRAP_CHECK (1 << 27) 465 466 /* 467 * SHR target access (Shared block memory space) 468 * 469 * Shared internal registers can be accessed directly from PCI bus through SHR 470 * arbiter without need for the MAC HW to be powered up. This is possible due to 471 * indirect read/write via HEEP_CTRL_WRD_PCIEX_CTRL (0xEC) and 472 * HEEP_CTRL_WRD_PCIEX_DATA (0xF4) registers. 473 * 474 * Use iwl_write32()/iwl_read32() family to access these registers. The MAC HW 475 * need not be powered up so no "grab inc access" is required. 476 */ 477 478 /* 479 * Registers for accessing shared registers (e.g. SHR_APMG_GP1, 480 * SHR_APMG_XTAL_CFG). For example, to read from SHR_APMG_GP1 register (0x1DC), 481 * first, write to the control register: 482 * HEEP_CTRL_WRD_PCIEX_CTRL[15:0] = 0x1DC (offset of the SHR_APMG_GP1 register) 483 * HEEP_CTRL_WRD_PCIEX_CTRL[29:28] = 2 (read access) 484 * second, read from the data register HEEP_CTRL_WRD_PCIEX_DATA[31:0]. 485 * 486 * To write the register, first, write to the data register 487 * HEEP_CTRL_WRD_PCIEX_DATA[31:0] and then: 488 * HEEP_CTRL_WRD_PCIEX_CTRL[15:0] = 0x1DC (offset of the SHR_APMG_GP1 register) 489 * HEEP_CTRL_WRD_PCIEX_CTRL[29:28] = 3 (write access) 490 */ 491 #define HEEP_CTRL_WRD_PCIEX_CTRL_REG (CSR_BASE+0x0ec) 492 #define HEEP_CTRL_WRD_PCIEX_DATA_REG (CSR_BASE+0x0f4) 493 494 /* 495 * HBUS (Host-side Bus) 496 * 497 * HBUS registers are mapped directly into PCI bus space, but are used 498 * to indirectly access device's internal memory or registers that 499 * may be powered-down. 500 * 501 * Use iwl_write_direct32()/iwl_read_direct32() family for these registers; 502 * host must "grab nic access" via CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ 503 * to make sure the MAC (uCode processor, etc.) is powered up for accessing 504 * internal resources. 505 * 506 * Do not use iwl_write32()/iwl_read32() family to access these registers; 507 * these provide only simple PCI bus access, without waking up the MAC. 508 */ 509 #define HBUS_BASE (0x400) 510 511 /* 512 * Registers for accessing device's internal SRAM memory (e.g. SCD SRAM 513 * structures, error log, event log, verifying uCode load). 514 * First write to address register, then read from or write to data register 515 * to complete the job. Once the address register is set up, accesses to 516 * data registers auto-increment the address by one dword. 517 * Bit usage for address registers (read or write): 518 * 0-31: memory address within device 519 */ 520 #define HBUS_TARG_MEM_RADDR (HBUS_BASE+0x00c) 521 #define HBUS_TARG_MEM_WADDR (HBUS_BASE+0x010) 522 #define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018) 523 #define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c) 524 525 /* Mailbox C, used as workaround alternative to CSR_UCODE_DRV_GP1 mailbox */ 526 #define HBUS_TARG_MBX_C (HBUS_BASE+0x030) 527 #define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004) 528 529 /* 530 * Registers for accessing device's internal peripheral registers 531 * (e.g. SCD, BSM, etc.). First write to address register, 532 * then read from or write to data register to complete the job. 533 * Bit usage for address registers (read or write): 534 * 0-15: register address (offset) within device 535 * 24-25: (# bytes - 1) to read or write (e.g. 3 for dword) 536 */ 537 #define HBUS_TARG_PRPH_WADDR (HBUS_BASE+0x044) 538 #define HBUS_TARG_PRPH_RADDR (HBUS_BASE+0x048) 539 #define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c) 540 #define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050) 541 542 /* Used to enable DBGM */ 543 #define HBUS_TARG_TEST_REG (HBUS_BASE+0x05c) 544 545 /* 546 * Per-Tx-queue write pointer (index, really!) 547 * Indicates index to next TFD that driver will fill (1 past latest filled). 548 * Bit usage: 549 * 0-7: queue write index 550 * 11-8: queue selector 551 */ 552 #define HBUS_TARG_WRPTR (HBUS_BASE+0x060) 553 /* This register is common for Tx and Rx, Rx queues start from 512 */ 554 #define HBUS_TARG_WRPTR_Q_SHIFT (16) 555 #define HBUS_TARG_WRPTR_RX_Q(q) (((q) + 512) << HBUS_TARG_WRPTR_Q_SHIFT) 556 557 /********************************************************** 558 * CSR values 559 **********************************************************/ 560 /* 561 * host interrupt timeout value 562 * used with setting interrupt coalescing timer 563 * the CSR_INT_COALESCING is an 8 bit register in 32-usec unit 564 * 565 * default interrupt coalescing timer is 64 x 32 = 2048 usecs 566 */ 567 #define IWL_HOST_INT_TIMEOUT_MAX (0xFF) 568 #define IWL_HOST_INT_TIMEOUT_DEF (0x40) 569 #define IWL_HOST_INT_TIMEOUT_MIN (0x0) 570 #define IWL_HOST_INT_OPER_MODE BIT(31) 571 572 /***************************************************************************** 573 * 7000/3000 series SHR DTS addresses * 574 *****************************************************************************/ 575 576 /* Diode Results Register Structure: */ 577 enum dtd_diode_reg { 578 DTS_DIODE_REG_DIG_VAL = 0x000000FF, /* bits [7:0] */ 579 DTS_DIODE_REG_VREF_LOW = 0x0000FF00, /* bits [15:8] */ 580 DTS_DIODE_REG_VREF_HIGH = 0x00FF0000, /* bits [23:16] */ 581 DTS_DIODE_REG_VREF_ID = 0x03000000, /* bits [25:24] */ 582 DTS_DIODE_REG_PASS_ONCE = 0x80000000, /* bits [31:31] */ 583 DTS_DIODE_REG_FLAGS_MSK = 0xFF000000, /* bits [31:24] */ 584 /* Those are the masks INSIDE the flags bit-field: */ 585 DTS_DIODE_REG_FLAGS_VREFS_ID_POS = 0, 586 DTS_DIODE_REG_FLAGS_VREFS_ID = 0x00000003, /* bits [1:0] */ 587 DTS_DIODE_REG_FLAGS_PASS_ONCE_POS = 7, 588 DTS_DIODE_REG_FLAGS_PASS_ONCE = 0x00000080, /* bits [7:7] */ 589 }; 590 591 /***************************************************************************** 592 * MSIX related registers * 593 *****************************************************************************/ 594 595 #define CSR_MSIX_BASE (0x2000) 596 #define CSR_MSIX_FH_INT_CAUSES_AD (CSR_MSIX_BASE + 0x800) 597 #define CSR_MSIX_FH_INT_MASK_AD (CSR_MSIX_BASE + 0x804) 598 #define CSR_MSIX_HW_INT_CAUSES_AD (CSR_MSIX_BASE + 0x808) 599 #define CSR_MSIX_HW_INT_MASK_AD (CSR_MSIX_BASE + 0x80C) 600 #define CSR_MSIX_AUTOMASK_ST_AD (CSR_MSIX_BASE + 0x810) 601 #define CSR_MSIX_RX_IVAR_AD_REG (CSR_MSIX_BASE + 0x880) 602 #define CSR_MSIX_IVAR_AD_REG (CSR_MSIX_BASE + 0x890) 603 #define CSR_MSIX_PENDING_PBA_AD (CSR_MSIX_BASE + 0x1000) 604 #define CSR_MSIX_RX_IVAR(cause) (CSR_MSIX_RX_IVAR_AD_REG + (cause)) 605 #define CSR_MSIX_IVAR(cause) (CSR_MSIX_IVAR_AD_REG + (cause)) 606 607 #define MSIX_FH_INT_CAUSES_Q(q) (q) 608 609 /* 610 * Causes for the FH register interrupts 611 */ 612 enum msix_fh_int_causes { 613 MSIX_FH_INT_CAUSES_Q0 = BIT(0), 614 MSIX_FH_INT_CAUSES_Q1 = BIT(1), 615 MSIX_FH_INT_CAUSES_D2S_CH0_NUM = BIT(16), 616 MSIX_FH_INT_CAUSES_D2S_CH1_NUM = BIT(17), 617 MSIX_FH_INT_CAUSES_S2D = BIT(19), 618 MSIX_FH_INT_CAUSES_FH_ERR = BIT(21), 619 }; 620 621 /* The low 16 bits are for rx data queue indication */ 622 #define MSIX_FH_INT_CAUSES_DATA_QUEUE 0xffff 623 624 /* 625 * Causes for the HW register interrupts 626 */ 627 enum msix_hw_int_causes { 628 MSIX_HW_INT_CAUSES_REG_ALIVE = BIT(0), 629 MSIX_HW_INT_CAUSES_REG_WAKEUP = BIT(1), 630 MSIX_HW_INT_CAUSES_REG_IML = BIT(1), 631 MSIX_HW_INT_CAUSES_REG_RESET_DONE = BIT(2), 632 MSIX_HW_INT_CAUSES_REG_TOP_FATAL_ERR = BIT(3), 633 MSIX_HW_INT_CAUSES_REG_SW_ERR_BZ = BIT(5), 634 MSIX_HW_INT_CAUSES_REG_CT_KILL = BIT(6), 635 MSIX_HW_INT_CAUSES_REG_RF_KILL = BIT(7), 636 MSIX_HW_INT_CAUSES_REG_PERIODIC = BIT(8), 637 MSIX_HW_INT_CAUSES_REG_SW_ERR = BIT(25), 638 MSIX_HW_INT_CAUSES_REG_SCD = BIT(26), 639 MSIX_HW_INT_CAUSES_REG_FH_TX = BIT(27), 640 MSIX_HW_INT_CAUSES_REG_HW_ERR = BIT(29), 641 MSIX_HW_INT_CAUSES_REG_HAP = BIT(30), 642 }; 643 644 #define MSIX_MIN_INTERRUPT_VECTORS 2 645 #define MSIX_AUTO_CLEAR_CAUSE 0 646 #define MSIX_NON_AUTO_CLEAR_CAUSE BIT(7) 647 648 /***************************************************************************** 649 * HW address related registers * 650 *****************************************************************************/ 651 652 #define CSR_ADDR_BASE(trans) ((trans)->cfg->mac_addr_from_csr) 653 #define CSR_MAC_ADDR0_OTP(trans) (CSR_ADDR_BASE(trans) + 0x00) 654 #define CSR_MAC_ADDR1_OTP(trans) (CSR_ADDR_BASE(trans) + 0x04) 655 #define CSR_MAC_ADDR0_STRAP(trans) (CSR_ADDR_BASE(trans) + 0x08) 656 #define CSR_MAC_ADDR1_STRAP(trans) (CSR_ADDR_BASE(trans) + 0x0c) 657 658 #endif /* !__iwl_csr_h__ */ 659