1 /* 2 * ASIX AX8817X based USB 2.0 Ethernet Devices 3 * Copyright (C) 2003-2006 David Hollis <dhollis@davehollis.com> 4 * Copyright (C) 2005 Phil Chang <pchang23@sbcglobal.net> 5 * Copyright (C) 2006 James Painter <jamie.painter@iname.com> 6 * Copyright (c) 2002-2003 TiVo Inc. 7 * 8 * This program is free software; you can redistribute it and/or modify 9 * it under the terms of the GNU General Public License as published by 10 * the Free Software Foundation; either version 2 of the License, or 11 * (at your option) any later version. 12 * 13 * This program is distributed in the hope that it will be useful, 14 * but WITHOUT ANY WARRANTY; without even the implied warranty of 15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 16 * GNU General Public License for more details. 17 * 18 * You should have received a copy of the GNU General Public License 19 * along with this program; if not, see <http://www.gnu.org/licenses/>. 20 */ 21 22 #include "asix.h" 23 24 #define PHY_MODE_MARVELL 0x0000 25 #define MII_MARVELL_LED_CTRL 0x0018 26 #define MII_MARVELL_STATUS 0x001b 27 #define MII_MARVELL_CTRL 0x0014 28 29 #define MARVELL_LED_MANUAL 0x0019 30 31 #define MARVELL_STATUS_HWCFG 0x0004 32 33 #define MARVELL_CTRL_TXDELAY 0x0002 34 #define MARVELL_CTRL_RXDELAY 0x0080 35 36 #define PHY_MODE_RTL8211CL 0x000C 37 38 #define AX88772A_PHY14H 0x14 39 #define AX88772A_PHY14H_DEFAULT 0x442C 40 41 #define AX88772A_PHY15H 0x15 42 #define AX88772A_PHY15H_DEFAULT 0x03C8 43 44 #define AX88772A_PHY16H 0x16 45 #define AX88772A_PHY16H_DEFAULT 0x4044 46 47 struct ax88172_int_data { 48 __le16 res1; 49 u8 link; 50 __le16 res2; 51 u8 status; 52 __le16 res3; 53 } __packed; 54 55 static void asix_status(struct usbnet *dev, struct urb *urb) 56 { 57 struct ax88172_int_data *event; 58 int link; 59 60 if (urb->actual_length < 8) 61 return; 62 63 event = urb->transfer_buffer; 64 link = event->link & 0x01; 65 if (netif_carrier_ok(dev->net) != link) { 66 usbnet_link_change(dev, link, 1); 67 netdev_dbg(dev->net, "Link Status is: %d\n", link); 68 } 69 } 70 71 static void asix_set_netdev_dev_addr(struct usbnet *dev, u8 *addr) 72 { 73 if (is_valid_ether_addr(addr)) { 74 memcpy(dev->net->dev_addr, addr, ETH_ALEN); 75 } else { 76 netdev_info(dev->net, "invalid hw address, using random\n"); 77 eth_hw_addr_random(dev->net); 78 } 79 } 80 81 /* Get the PHY Identifier from the PHYSID1 & PHYSID2 MII registers */ 82 static u32 asix_get_phyid(struct usbnet *dev) 83 { 84 int phy_reg; 85 u32 phy_id; 86 int i; 87 88 /* Poll for the rare case the FW or phy isn't ready yet. */ 89 for (i = 0; i < 100; i++) { 90 phy_reg = asix_mdio_read(dev->net, dev->mii.phy_id, MII_PHYSID1); 91 if (phy_reg < 0) 92 return 0; 93 if (phy_reg != 0 && phy_reg != 0xFFFF) 94 break; 95 mdelay(1); 96 } 97 98 if (phy_reg <= 0 || phy_reg == 0xFFFF) 99 return 0; 100 101 phy_id = (phy_reg & 0xffff) << 16; 102 103 phy_reg = asix_mdio_read(dev->net, dev->mii.phy_id, MII_PHYSID2); 104 if (phy_reg < 0) 105 return 0; 106 107 phy_id |= (phy_reg & 0xffff); 108 109 return phy_id; 110 } 111 112 static u32 asix_get_link(struct net_device *net) 113 { 114 struct usbnet *dev = netdev_priv(net); 115 116 return mii_link_ok(&dev->mii); 117 } 118 119 static int asix_ioctl (struct net_device *net, struct ifreq *rq, int cmd) 120 { 121 struct usbnet *dev = netdev_priv(net); 122 123 return generic_mii_ioctl(&dev->mii, if_mii(rq), cmd, NULL); 124 } 125 126 /* We need to override some ethtool_ops so we require our 127 own structure so we don't interfere with other usbnet 128 devices that may be connected at the same time. */ 129 static const struct ethtool_ops ax88172_ethtool_ops = { 130 .get_drvinfo = asix_get_drvinfo, 131 .get_link = asix_get_link, 132 .get_msglevel = usbnet_get_msglevel, 133 .set_msglevel = usbnet_set_msglevel, 134 .get_wol = asix_get_wol, 135 .set_wol = asix_set_wol, 136 .get_eeprom_len = asix_get_eeprom_len, 137 .get_eeprom = asix_get_eeprom, 138 .set_eeprom = asix_set_eeprom, 139 .get_settings = usbnet_get_settings, 140 .set_settings = usbnet_set_settings, 141 .nway_reset = usbnet_nway_reset, 142 }; 143 144 static void ax88172_set_multicast(struct net_device *net) 145 { 146 struct usbnet *dev = netdev_priv(net); 147 struct asix_data *data = (struct asix_data *)&dev->data; 148 u8 rx_ctl = 0x8c; 149 150 if (net->flags & IFF_PROMISC) { 151 rx_ctl |= 0x01; 152 } else if (net->flags & IFF_ALLMULTI || 153 netdev_mc_count(net) > AX_MAX_MCAST) { 154 rx_ctl |= 0x02; 155 } else if (netdev_mc_empty(net)) { 156 /* just broadcast and directed */ 157 } else { 158 /* We use the 20 byte dev->data 159 * for our 8 byte filter buffer 160 * to avoid allocating memory that 161 * is tricky to free later */ 162 struct netdev_hw_addr *ha; 163 u32 crc_bits; 164 165 memset(data->multi_filter, 0, AX_MCAST_FILTER_SIZE); 166 167 /* Build the multicast hash filter. */ 168 netdev_for_each_mc_addr(ha, net) { 169 crc_bits = ether_crc(ETH_ALEN, ha->addr) >> 26; 170 data->multi_filter[crc_bits >> 3] |= 171 1 << (crc_bits & 7); 172 } 173 174 asix_write_cmd_async(dev, AX_CMD_WRITE_MULTI_FILTER, 0, 0, 175 AX_MCAST_FILTER_SIZE, data->multi_filter); 176 177 rx_ctl |= 0x10; 178 } 179 180 asix_write_cmd_async(dev, AX_CMD_WRITE_RX_CTL, rx_ctl, 0, 0, NULL); 181 } 182 183 static int ax88172_link_reset(struct usbnet *dev) 184 { 185 u8 mode; 186 struct ethtool_cmd ecmd = { .cmd = ETHTOOL_GSET }; 187 188 mii_check_media(&dev->mii, 1, 1); 189 mii_ethtool_gset(&dev->mii, &ecmd); 190 mode = AX88172_MEDIUM_DEFAULT; 191 192 if (ecmd.duplex != DUPLEX_FULL) 193 mode |= ~AX88172_MEDIUM_FD; 194 195 netdev_dbg(dev->net, "ax88172_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n", 196 ethtool_cmd_speed(&ecmd), ecmd.duplex, mode); 197 198 asix_write_medium_mode(dev, mode, 0); 199 200 return 0; 201 } 202 203 static const struct net_device_ops ax88172_netdev_ops = { 204 .ndo_open = usbnet_open, 205 .ndo_stop = usbnet_stop, 206 .ndo_start_xmit = usbnet_start_xmit, 207 .ndo_tx_timeout = usbnet_tx_timeout, 208 .ndo_change_mtu = usbnet_change_mtu, 209 .ndo_set_mac_address = eth_mac_addr, 210 .ndo_validate_addr = eth_validate_addr, 211 .ndo_do_ioctl = asix_ioctl, 212 .ndo_set_rx_mode = ax88172_set_multicast, 213 }; 214 215 static void asix_phy_reset(struct usbnet *dev, unsigned int reset_bits) 216 { 217 unsigned int timeout = 5000; 218 219 asix_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, reset_bits); 220 221 /* give phy_id a chance to process reset */ 222 udelay(500); 223 224 /* See IEEE 802.3 "22.2.4.1.1 Reset": 500ms max */ 225 while (timeout--) { 226 if (asix_mdio_read(dev->net, dev->mii.phy_id, MII_BMCR) 227 & BMCR_RESET) 228 udelay(100); 229 else 230 return; 231 } 232 233 netdev_err(dev->net, "BMCR_RESET timeout on phy_id %d\n", 234 dev->mii.phy_id); 235 } 236 237 static int ax88172_bind(struct usbnet *dev, struct usb_interface *intf) 238 { 239 int ret = 0; 240 u8 buf[ETH_ALEN]; 241 int i; 242 unsigned long gpio_bits = dev->driver_info->data; 243 244 usbnet_get_endpoints(dev,intf); 245 246 /* Toggle the GPIOs in a manufacturer/model specific way */ 247 for (i = 2; i >= 0; i--) { 248 ret = asix_write_cmd(dev, AX_CMD_WRITE_GPIOS, 249 (gpio_bits >> (i * 8)) & 0xff, 0, 0, NULL, 0); 250 if (ret < 0) 251 goto out; 252 msleep(5); 253 } 254 255 ret = asix_write_rx_ctl(dev, 0x80, 0); 256 if (ret < 0) 257 goto out; 258 259 /* Get the MAC address */ 260 ret = asix_read_cmd(dev, AX88172_CMD_READ_NODE_ID, 261 0, 0, ETH_ALEN, buf, 0); 262 if (ret < 0) { 263 netdev_dbg(dev->net, "read AX_CMD_READ_NODE_ID failed: %d\n", 264 ret); 265 goto out; 266 } 267 268 asix_set_netdev_dev_addr(dev, buf); 269 270 /* Initialize MII structure */ 271 dev->mii.dev = dev->net; 272 dev->mii.mdio_read = asix_mdio_read; 273 dev->mii.mdio_write = asix_mdio_write; 274 dev->mii.phy_id_mask = 0x3f; 275 dev->mii.reg_num_mask = 0x1f; 276 dev->mii.phy_id = asix_get_phy_addr(dev); 277 278 dev->net->netdev_ops = &ax88172_netdev_ops; 279 dev->net->ethtool_ops = &ax88172_ethtool_ops; 280 dev->net->needed_headroom = 4; /* cf asix_tx_fixup() */ 281 dev->net->needed_tailroom = 4; /* cf asix_tx_fixup() */ 282 283 asix_phy_reset(dev, BMCR_RESET); 284 asix_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE, 285 ADVERTISE_ALL | ADVERTISE_CSMA | ADVERTISE_PAUSE_CAP); 286 mii_nway_restart(&dev->mii); 287 288 return 0; 289 290 out: 291 return ret; 292 } 293 294 static const struct ethtool_ops ax88772_ethtool_ops = { 295 .get_drvinfo = asix_get_drvinfo, 296 .get_link = asix_get_link, 297 .get_msglevel = usbnet_get_msglevel, 298 .set_msglevel = usbnet_set_msglevel, 299 .get_wol = asix_get_wol, 300 .set_wol = asix_set_wol, 301 .get_eeprom_len = asix_get_eeprom_len, 302 .get_eeprom = asix_get_eeprom, 303 .set_eeprom = asix_set_eeprom, 304 .get_settings = usbnet_get_settings, 305 .set_settings = usbnet_set_settings, 306 .nway_reset = usbnet_nway_reset, 307 }; 308 309 static int ax88772_link_reset(struct usbnet *dev) 310 { 311 u16 mode; 312 struct ethtool_cmd ecmd = { .cmd = ETHTOOL_GSET }; 313 314 mii_check_media(&dev->mii, 1, 1); 315 mii_ethtool_gset(&dev->mii, &ecmd); 316 mode = AX88772_MEDIUM_DEFAULT; 317 318 if (ethtool_cmd_speed(&ecmd) != SPEED_100) 319 mode &= ~AX_MEDIUM_PS; 320 321 if (ecmd.duplex != DUPLEX_FULL) 322 mode &= ~AX_MEDIUM_FD; 323 324 netdev_dbg(dev->net, "ax88772_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n", 325 ethtool_cmd_speed(&ecmd), ecmd.duplex, mode); 326 327 asix_write_medium_mode(dev, mode, 0); 328 329 return 0; 330 } 331 332 static int ax88772_reset(struct usbnet *dev) 333 { 334 struct asix_data *data = (struct asix_data *)&dev->data; 335 int ret; 336 337 /* Rewrite MAC address */ 338 ether_addr_copy(data->mac_addr, dev->net->dev_addr); 339 ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, 340 ETH_ALEN, data->mac_addr, 0); 341 if (ret < 0) 342 goto out; 343 344 /* Set RX_CTL to default values with 2k buffer, and enable cactus */ 345 ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, 0); 346 if (ret < 0) 347 goto out; 348 349 asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, 0); 350 if (ret < 0) 351 goto out; 352 353 return 0; 354 355 out: 356 return ret; 357 } 358 359 static int ax88772_hw_reset(struct usbnet *dev, int in_pm) 360 { 361 struct asix_data *data = (struct asix_data *)&dev->data; 362 int ret, embd_phy; 363 u16 rx_ctl; 364 365 ret = asix_write_gpio(dev, AX_GPIO_RSE | AX_GPIO_GPO_2 | 366 AX_GPIO_GPO2EN, 5, in_pm); 367 if (ret < 0) 368 goto out; 369 370 embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0); 371 372 ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy, 373 0, 0, NULL, in_pm); 374 if (ret < 0) { 375 netdev_dbg(dev->net, "Select PHY #1 failed: %d\n", ret); 376 goto out; 377 } 378 379 if (embd_phy) { 380 ret = asix_sw_reset(dev, AX_SWRESET_IPPD, in_pm); 381 if (ret < 0) 382 goto out; 383 384 usleep_range(10000, 11000); 385 386 ret = asix_sw_reset(dev, AX_SWRESET_CLEAR, in_pm); 387 if (ret < 0) 388 goto out; 389 390 msleep(60); 391 392 ret = asix_sw_reset(dev, AX_SWRESET_IPRL | AX_SWRESET_PRL, 393 in_pm); 394 if (ret < 0) 395 goto out; 396 } else { 397 ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_PRL, 398 in_pm); 399 if (ret < 0) 400 goto out; 401 } 402 403 msleep(150); 404 405 if (in_pm && (!asix_mdio_read_nopm(dev->net, dev->mii.phy_id, 406 MII_PHYSID1))){ 407 ret = -EIO; 408 goto out; 409 } 410 411 ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm); 412 if (ret < 0) 413 goto out; 414 415 ret = asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, in_pm); 416 if (ret < 0) 417 goto out; 418 419 ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0, 420 AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT, 421 AX88772_IPG2_DEFAULT, 0, NULL, in_pm); 422 if (ret < 0) { 423 netdev_dbg(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret); 424 goto out; 425 } 426 427 /* Rewrite MAC address */ 428 ether_addr_copy(data->mac_addr, dev->net->dev_addr); 429 ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, 430 ETH_ALEN, data->mac_addr, in_pm); 431 if (ret < 0) 432 goto out; 433 434 /* Set RX_CTL to default values with 2k buffer, and enable cactus */ 435 ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm); 436 if (ret < 0) 437 goto out; 438 439 rx_ctl = asix_read_rx_ctl(dev, in_pm); 440 netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n", 441 rx_ctl); 442 443 rx_ctl = asix_read_medium_status(dev, in_pm); 444 netdev_dbg(dev->net, 445 "Medium Status is 0x%04x after all initializations\n", 446 rx_ctl); 447 448 return 0; 449 450 out: 451 return ret; 452 } 453 454 static int ax88772a_hw_reset(struct usbnet *dev, int in_pm) 455 { 456 struct asix_data *data = (struct asix_data *)&dev->data; 457 int ret, embd_phy; 458 u16 rx_ctl, phy14h, phy15h, phy16h; 459 u8 chipcode = 0; 460 461 ret = asix_write_gpio(dev, AX_GPIO_RSE, 5, in_pm); 462 if (ret < 0) 463 goto out; 464 465 embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0); 466 467 ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy | 468 AX_PHYSEL_SSEN, 0, 0, NULL, in_pm); 469 if (ret < 0) { 470 netdev_dbg(dev->net, "Select PHY #1 failed: %d\n", ret); 471 goto out; 472 } 473 usleep_range(10000, 11000); 474 475 ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_IPRL, in_pm); 476 if (ret < 0) 477 goto out; 478 479 usleep_range(10000, 11000); 480 481 ret = asix_sw_reset(dev, AX_SWRESET_IPRL, in_pm); 482 if (ret < 0) 483 goto out; 484 485 msleep(160); 486 487 ret = asix_sw_reset(dev, AX_SWRESET_CLEAR, in_pm); 488 if (ret < 0) 489 goto out; 490 491 ret = asix_sw_reset(dev, AX_SWRESET_IPRL, in_pm); 492 if (ret < 0) 493 goto out; 494 495 msleep(200); 496 497 if (in_pm && (!asix_mdio_read_nopm(dev->net, dev->mii.phy_id, 498 MII_PHYSID1))) { 499 ret = -1; 500 goto out; 501 } 502 503 ret = asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 504 0, 1, &chipcode, in_pm); 505 if (ret < 0) 506 goto out; 507 508 if ((chipcode & AX_CHIPCODE_MASK) == AX_AX88772B_CHIPCODE) { 509 ret = asix_write_cmd(dev, AX_QCTCTRL, 0x8000, 0x8001, 510 0, NULL, in_pm); 511 if (ret < 0) { 512 netdev_dbg(dev->net, "Write BQ setting failed: %d\n", 513 ret); 514 goto out; 515 } 516 } else if ((chipcode & AX_CHIPCODE_MASK) == AX_AX88772A_CHIPCODE) { 517 /* Check if the PHY registers have default settings */ 518 phy14h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id, 519 AX88772A_PHY14H); 520 phy15h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id, 521 AX88772A_PHY15H); 522 phy16h = asix_mdio_read_nopm(dev->net, dev->mii.phy_id, 523 AX88772A_PHY16H); 524 525 netdev_dbg(dev->net, 526 "772a_hw_reset: MR20=0x%x MR21=0x%x MR22=0x%x\n", 527 phy14h, phy15h, phy16h); 528 529 /* Restore PHY registers default setting if not */ 530 if (phy14h != AX88772A_PHY14H_DEFAULT) 531 asix_mdio_write_nopm(dev->net, dev->mii.phy_id, 532 AX88772A_PHY14H, 533 AX88772A_PHY14H_DEFAULT); 534 if (phy15h != AX88772A_PHY15H_DEFAULT) 535 asix_mdio_write_nopm(dev->net, dev->mii.phy_id, 536 AX88772A_PHY15H, 537 AX88772A_PHY15H_DEFAULT); 538 if (phy16h != AX88772A_PHY16H_DEFAULT) 539 asix_mdio_write_nopm(dev->net, dev->mii.phy_id, 540 AX88772A_PHY16H, 541 AX88772A_PHY16H_DEFAULT); 542 } 543 544 ret = asix_write_cmd(dev, AX_CMD_WRITE_IPG0, 545 AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT, 546 AX88772_IPG2_DEFAULT, 0, NULL, in_pm); 547 if (ret < 0) { 548 netdev_dbg(dev->net, "Write IPG,IPG1,IPG2 failed: %d\n", ret); 549 goto out; 550 } 551 552 /* Rewrite MAC address */ 553 memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN); 554 ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN, 555 data->mac_addr, in_pm); 556 if (ret < 0) 557 goto out; 558 559 /* Set RX_CTL to default values with 2k buffer, and enable cactus */ 560 ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm); 561 if (ret < 0) 562 goto out; 563 564 ret = asix_write_medium_mode(dev, AX88772_MEDIUM_DEFAULT, in_pm); 565 if (ret < 0) 566 return ret; 567 568 /* Set RX_CTL to default values with 2k buffer, and enable cactus */ 569 ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, in_pm); 570 if (ret < 0) 571 goto out; 572 573 rx_ctl = asix_read_rx_ctl(dev, in_pm); 574 netdev_dbg(dev->net, "RX_CTL is 0x%04x after all initializations\n", 575 rx_ctl); 576 577 rx_ctl = asix_read_medium_status(dev, in_pm); 578 netdev_dbg(dev->net, 579 "Medium Status is 0x%04x after all initializations\n", 580 rx_ctl); 581 582 return 0; 583 584 out: 585 return ret; 586 } 587 588 static const struct net_device_ops ax88772_netdev_ops = { 589 .ndo_open = usbnet_open, 590 .ndo_stop = usbnet_stop, 591 .ndo_start_xmit = usbnet_start_xmit, 592 .ndo_tx_timeout = usbnet_tx_timeout, 593 .ndo_change_mtu = usbnet_change_mtu, 594 .ndo_set_mac_address = asix_set_mac_address, 595 .ndo_validate_addr = eth_validate_addr, 596 .ndo_do_ioctl = asix_ioctl, 597 .ndo_set_rx_mode = asix_set_multicast, 598 }; 599 600 static void ax88772_suspend(struct usbnet *dev) 601 { 602 struct asix_common_private *priv = dev->driver_priv; 603 u16 medium; 604 605 /* Stop MAC operation */ 606 medium = asix_read_medium_status(dev, 0); 607 medium &= ~AX_MEDIUM_RE; 608 asix_write_medium_mode(dev, medium, 0); 609 610 netdev_dbg(dev->net, "ax88772_suspend: medium=0x%04x\n", 611 asix_read_medium_status(dev, 0)); 612 613 /* Preserve BMCR for restoring */ 614 priv->presvd_phy_bmcr = 615 asix_mdio_read_nopm(dev->net, dev->mii.phy_id, MII_BMCR); 616 617 /* Preserve ANAR for restoring */ 618 priv->presvd_phy_advertise = 619 asix_mdio_read_nopm(dev->net, dev->mii.phy_id, MII_ADVERTISE); 620 } 621 622 static int asix_suspend(struct usb_interface *intf, pm_message_t message) 623 { 624 struct usbnet *dev = usb_get_intfdata(intf); 625 struct asix_common_private *priv = dev->driver_priv; 626 627 if (priv->suspend) 628 priv->suspend(dev); 629 630 return usbnet_suspend(intf, message); 631 } 632 633 static void ax88772_restore_phy(struct usbnet *dev) 634 { 635 struct asix_common_private *priv = dev->driver_priv; 636 637 if (priv->presvd_phy_advertise) { 638 /* Restore Advertisement control reg */ 639 asix_mdio_write_nopm(dev->net, dev->mii.phy_id, MII_ADVERTISE, 640 priv->presvd_phy_advertise); 641 642 /* Restore BMCR */ 643 asix_mdio_write_nopm(dev->net, dev->mii.phy_id, MII_BMCR, 644 priv->presvd_phy_bmcr); 645 646 mii_nway_restart(&dev->mii); 647 priv->presvd_phy_advertise = 0; 648 priv->presvd_phy_bmcr = 0; 649 } 650 } 651 652 static void ax88772_resume(struct usbnet *dev) 653 { 654 int i; 655 656 for (i = 0; i < 3; i++) 657 if (!ax88772_hw_reset(dev, 1)) 658 break; 659 ax88772_restore_phy(dev); 660 } 661 662 static void ax88772a_resume(struct usbnet *dev) 663 { 664 int i; 665 666 for (i = 0; i < 3; i++) { 667 if (!ax88772a_hw_reset(dev, 1)) 668 break; 669 } 670 671 ax88772_restore_phy(dev); 672 } 673 674 static int asix_resume(struct usb_interface *intf) 675 { 676 struct usbnet *dev = usb_get_intfdata(intf); 677 struct asix_common_private *priv = dev->driver_priv; 678 679 if (priv->resume) 680 priv->resume(dev); 681 682 return usbnet_resume(intf); 683 } 684 685 static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf) 686 { 687 int ret, i; 688 u8 buf[ETH_ALEN], chipcode = 0; 689 u32 phyid; 690 struct asix_common_private *priv; 691 692 usbnet_get_endpoints(dev,intf); 693 694 /* Get the MAC address */ 695 if (dev->driver_info->data & FLAG_EEPROM_MAC) { 696 for (i = 0; i < (ETH_ALEN >> 1); i++) { 697 ret = asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x04 + i, 698 0, 2, buf + i * 2, 0); 699 if (ret < 0) 700 break; 701 } 702 } else { 703 ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 704 0, 0, ETH_ALEN, buf, 0); 705 } 706 707 if (ret < 0) { 708 netdev_dbg(dev->net, "Failed to read MAC address: %d\n", ret); 709 return ret; 710 } 711 712 asix_set_netdev_dev_addr(dev, buf); 713 714 /* Initialize MII structure */ 715 dev->mii.dev = dev->net; 716 dev->mii.mdio_read = asix_mdio_read; 717 dev->mii.mdio_write = asix_mdio_write; 718 dev->mii.phy_id_mask = 0x1f; 719 dev->mii.reg_num_mask = 0x1f; 720 dev->mii.phy_id = asix_get_phy_addr(dev); 721 722 dev->net->netdev_ops = &ax88772_netdev_ops; 723 dev->net->ethtool_ops = &ax88772_ethtool_ops; 724 dev->net->needed_headroom = 4; /* cf asix_tx_fixup() */ 725 dev->net->needed_tailroom = 4; /* cf asix_tx_fixup() */ 726 727 asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &chipcode, 0); 728 chipcode &= AX_CHIPCODE_MASK; 729 730 (chipcode == AX_AX88772_CHIPCODE) ? ax88772_hw_reset(dev, 0) : 731 ax88772a_hw_reset(dev, 0); 732 733 /* Read PHYID register *AFTER* the PHY was reset properly */ 734 phyid = asix_get_phyid(dev); 735 netdev_dbg(dev->net, "PHYID=0x%08x\n", phyid); 736 737 /* Asix framing packs multiple eth frames into a 2K usb bulk transfer */ 738 if (dev->driver_info->flags & FLAG_FRAMING_AX) { 739 /* hard_mtu is still the default - the device does not support 740 jumbo eth frames */ 741 dev->rx_urb_size = 2048; 742 } 743 744 dev->driver_priv = kzalloc(sizeof(struct asix_common_private), GFP_KERNEL); 745 if (!dev->driver_priv) 746 return -ENOMEM; 747 748 priv = dev->driver_priv; 749 750 priv->presvd_phy_bmcr = 0; 751 priv->presvd_phy_advertise = 0; 752 if (chipcode == AX_AX88772_CHIPCODE) { 753 priv->resume = ax88772_resume; 754 priv->suspend = ax88772_suspend; 755 } else { 756 priv->resume = ax88772a_resume; 757 priv->suspend = ax88772_suspend; 758 } 759 760 return 0; 761 } 762 763 static void ax88772_unbind(struct usbnet *dev, struct usb_interface *intf) 764 { 765 kfree(dev->driver_priv); 766 } 767 768 static const struct ethtool_ops ax88178_ethtool_ops = { 769 .get_drvinfo = asix_get_drvinfo, 770 .get_link = asix_get_link, 771 .get_msglevel = usbnet_get_msglevel, 772 .set_msglevel = usbnet_set_msglevel, 773 .get_wol = asix_get_wol, 774 .set_wol = asix_set_wol, 775 .get_eeprom_len = asix_get_eeprom_len, 776 .get_eeprom = asix_get_eeprom, 777 .set_eeprom = asix_set_eeprom, 778 .get_settings = usbnet_get_settings, 779 .set_settings = usbnet_set_settings, 780 .nway_reset = usbnet_nway_reset, 781 }; 782 783 static int marvell_phy_init(struct usbnet *dev) 784 { 785 struct asix_data *data = (struct asix_data *)&dev->data; 786 u16 reg; 787 788 netdev_dbg(dev->net, "marvell_phy_init()\n"); 789 790 reg = asix_mdio_read(dev->net, dev->mii.phy_id, MII_MARVELL_STATUS); 791 netdev_dbg(dev->net, "MII_MARVELL_STATUS = 0x%04x\n", reg); 792 793 asix_mdio_write(dev->net, dev->mii.phy_id, MII_MARVELL_CTRL, 794 MARVELL_CTRL_RXDELAY | MARVELL_CTRL_TXDELAY); 795 796 if (data->ledmode) { 797 reg = asix_mdio_read(dev->net, dev->mii.phy_id, 798 MII_MARVELL_LED_CTRL); 799 netdev_dbg(dev->net, "MII_MARVELL_LED_CTRL (1) = 0x%04x\n", reg); 800 801 reg &= 0xf8ff; 802 reg |= (1 + 0x0100); 803 asix_mdio_write(dev->net, dev->mii.phy_id, 804 MII_MARVELL_LED_CTRL, reg); 805 806 reg = asix_mdio_read(dev->net, dev->mii.phy_id, 807 MII_MARVELL_LED_CTRL); 808 netdev_dbg(dev->net, "MII_MARVELL_LED_CTRL (2) = 0x%04x\n", reg); 809 reg &= 0xfc0f; 810 } 811 812 return 0; 813 } 814 815 static int rtl8211cl_phy_init(struct usbnet *dev) 816 { 817 struct asix_data *data = (struct asix_data *)&dev->data; 818 819 netdev_dbg(dev->net, "rtl8211cl_phy_init()\n"); 820 821 asix_mdio_write (dev->net, dev->mii.phy_id, 0x1f, 0x0005); 822 asix_mdio_write (dev->net, dev->mii.phy_id, 0x0c, 0); 823 asix_mdio_write (dev->net, dev->mii.phy_id, 0x01, 824 asix_mdio_read (dev->net, dev->mii.phy_id, 0x01) | 0x0080); 825 asix_mdio_write (dev->net, dev->mii.phy_id, 0x1f, 0); 826 827 if (data->ledmode == 12) { 828 asix_mdio_write (dev->net, dev->mii.phy_id, 0x1f, 0x0002); 829 asix_mdio_write (dev->net, dev->mii.phy_id, 0x1a, 0x00cb); 830 asix_mdio_write (dev->net, dev->mii.phy_id, 0x1f, 0); 831 } 832 833 return 0; 834 } 835 836 static int marvell_led_status(struct usbnet *dev, u16 speed) 837 { 838 u16 reg = asix_mdio_read(dev->net, dev->mii.phy_id, MARVELL_LED_MANUAL); 839 840 netdev_dbg(dev->net, "marvell_led_status() read 0x%04x\n", reg); 841 842 /* Clear out the center LED bits - 0x03F0 */ 843 reg &= 0xfc0f; 844 845 switch (speed) { 846 case SPEED_1000: 847 reg |= 0x03e0; 848 break; 849 case SPEED_100: 850 reg |= 0x03b0; 851 break; 852 default: 853 reg |= 0x02f0; 854 } 855 856 netdev_dbg(dev->net, "marvell_led_status() writing 0x%04x\n", reg); 857 asix_mdio_write(dev->net, dev->mii.phy_id, MARVELL_LED_MANUAL, reg); 858 859 return 0; 860 } 861 862 static int ax88178_reset(struct usbnet *dev) 863 { 864 struct asix_data *data = (struct asix_data *)&dev->data; 865 int ret; 866 __le16 eeprom; 867 u8 status; 868 int gpio0 = 0; 869 u32 phyid; 870 871 asix_read_cmd(dev, AX_CMD_READ_GPIOS, 0, 0, 1, &status, 0); 872 netdev_dbg(dev->net, "GPIO Status: 0x%04x\n", status); 873 874 asix_write_cmd(dev, AX_CMD_WRITE_ENABLE, 0, 0, 0, NULL, 0); 875 asix_read_cmd(dev, AX_CMD_READ_EEPROM, 0x0017, 0, 2, &eeprom, 0); 876 asix_write_cmd(dev, AX_CMD_WRITE_DISABLE, 0, 0, 0, NULL, 0); 877 878 netdev_dbg(dev->net, "EEPROM index 0x17 is 0x%04x\n", eeprom); 879 880 if (eeprom == cpu_to_le16(0xffff)) { 881 data->phymode = PHY_MODE_MARVELL; 882 data->ledmode = 0; 883 gpio0 = 1; 884 } else { 885 data->phymode = le16_to_cpu(eeprom) & 0x7F; 886 data->ledmode = le16_to_cpu(eeprom) >> 8; 887 gpio0 = (le16_to_cpu(eeprom) & 0x80) ? 0 : 1; 888 } 889 netdev_dbg(dev->net, "GPIO0: %d, PhyMode: %d\n", gpio0, data->phymode); 890 891 /* Power up external GigaPHY through AX88178 GPIO pin */ 892 asix_write_gpio(dev, AX_GPIO_RSE | AX_GPIO_GPO_1 | 893 AX_GPIO_GPO1EN, 40, 0); 894 if ((le16_to_cpu(eeprom) >> 8) != 1) { 895 asix_write_gpio(dev, 0x003c, 30, 0); 896 asix_write_gpio(dev, 0x001c, 300, 0); 897 asix_write_gpio(dev, 0x003c, 30, 0); 898 } else { 899 netdev_dbg(dev->net, "gpio phymode == 1 path\n"); 900 asix_write_gpio(dev, AX_GPIO_GPO1EN, 30, 0); 901 asix_write_gpio(dev, AX_GPIO_GPO1EN | AX_GPIO_GPO_1, 30, 0); 902 } 903 904 /* Read PHYID register *AFTER* powering up PHY */ 905 phyid = asix_get_phyid(dev); 906 netdev_dbg(dev->net, "PHYID=0x%08x\n", phyid); 907 908 /* Set AX88178 to enable MII/GMII/RGMII interface for external PHY */ 909 asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, 0, 0, 0, NULL, 0); 910 911 asix_sw_reset(dev, 0, 0); 912 msleep(150); 913 914 asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD, 0); 915 msleep(150); 916 917 asix_write_rx_ctl(dev, 0, 0); 918 919 if (data->phymode == PHY_MODE_MARVELL) { 920 marvell_phy_init(dev); 921 msleep(60); 922 } else if (data->phymode == PHY_MODE_RTL8211CL) 923 rtl8211cl_phy_init(dev); 924 925 asix_phy_reset(dev, BMCR_RESET | BMCR_ANENABLE); 926 asix_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE, 927 ADVERTISE_ALL | ADVERTISE_CSMA | ADVERTISE_PAUSE_CAP); 928 asix_mdio_write(dev->net, dev->mii.phy_id, MII_CTRL1000, 929 ADVERTISE_1000FULL); 930 931 asix_write_medium_mode(dev, AX88178_MEDIUM_DEFAULT, 0); 932 mii_nway_restart(&dev->mii); 933 934 /* Rewrite MAC address */ 935 memcpy(data->mac_addr, dev->net->dev_addr, ETH_ALEN); 936 ret = asix_write_cmd(dev, AX_CMD_WRITE_NODE_ID, 0, 0, ETH_ALEN, 937 data->mac_addr, 0); 938 if (ret < 0) 939 return ret; 940 941 ret = asix_write_rx_ctl(dev, AX_DEFAULT_RX_CTL, 0); 942 if (ret < 0) 943 return ret; 944 945 return 0; 946 } 947 948 static int ax88178_link_reset(struct usbnet *dev) 949 { 950 u16 mode; 951 struct ethtool_cmd ecmd = { .cmd = ETHTOOL_GSET }; 952 struct asix_data *data = (struct asix_data *)&dev->data; 953 u32 speed; 954 955 netdev_dbg(dev->net, "ax88178_link_reset()\n"); 956 957 mii_check_media(&dev->mii, 1, 1); 958 mii_ethtool_gset(&dev->mii, &ecmd); 959 mode = AX88178_MEDIUM_DEFAULT; 960 speed = ethtool_cmd_speed(&ecmd); 961 962 if (speed == SPEED_1000) 963 mode |= AX_MEDIUM_GM; 964 else if (speed == SPEED_100) 965 mode |= AX_MEDIUM_PS; 966 else 967 mode &= ~(AX_MEDIUM_PS | AX_MEDIUM_GM); 968 969 mode |= AX_MEDIUM_ENCK; 970 971 if (ecmd.duplex == DUPLEX_FULL) 972 mode |= AX_MEDIUM_FD; 973 else 974 mode &= ~AX_MEDIUM_FD; 975 976 netdev_dbg(dev->net, "ax88178_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n", 977 speed, ecmd.duplex, mode); 978 979 asix_write_medium_mode(dev, mode, 0); 980 981 if (data->phymode == PHY_MODE_MARVELL && data->ledmode) 982 marvell_led_status(dev, speed); 983 984 return 0; 985 } 986 987 static void ax88178_set_mfb(struct usbnet *dev) 988 { 989 u16 mfb = AX_RX_CTL_MFB_16384; 990 u16 rxctl; 991 u16 medium; 992 int old_rx_urb_size = dev->rx_urb_size; 993 994 if (dev->hard_mtu < 2048) { 995 dev->rx_urb_size = 2048; 996 mfb = AX_RX_CTL_MFB_2048; 997 } else if (dev->hard_mtu < 4096) { 998 dev->rx_urb_size = 4096; 999 mfb = AX_RX_CTL_MFB_4096; 1000 } else if (dev->hard_mtu < 8192) { 1001 dev->rx_urb_size = 8192; 1002 mfb = AX_RX_CTL_MFB_8192; 1003 } else if (dev->hard_mtu < 16384) { 1004 dev->rx_urb_size = 16384; 1005 mfb = AX_RX_CTL_MFB_16384; 1006 } 1007 1008 rxctl = asix_read_rx_ctl(dev, 0); 1009 asix_write_rx_ctl(dev, (rxctl & ~AX_RX_CTL_MFB_16384) | mfb, 0); 1010 1011 medium = asix_read_medium_status(dev, 0); 1012 if (dev->net->mtu > 1500) 1013 medium |= AX_MEDIUM_JFE; 1014 else 1015 medium &= ~AX_MEDIUM_JFE; 1016 asix_write_medium_mode(dev, medium, 0); 1017 1018 if (dev->rx_urb_size > old_rx_urb_size) 1019 usbnet_unlink_rx_urbs(dev); 1020 } 1021 1022 static int ax88178_change_mtu(struct net_device *net, int new_mtu) 1023 { 1024 struct usbnet *dev = netdev_priv(net); 1025 int ll_mtu = new_mtu + net->hard_header_len + 4; 1026 1027 netdev_dbg(dev->net, "ax88178_change_mtu() new_mtu=%d\n", new_mtu); 1028 1029 if (new_mtu <= 0 || ll_mtu > 16384) 1030 return -EINVAL; 1031 1032 if ((ll_mtu % dev->maxpacket) == 0) 1033 return -EDOM; 1034 1035 net->mtu = new_mtu; 1036 dev->hard_mtu = net->mtu + net->hard_header_len; 1037 ax88178_set_mfb(dev); 1038 1039 /* max qlen depend on hard_mtu and rx_urb_size */ 1040 usbnet_update_max_qlen(dev); 1041 1042 return 0; 1043 } 1044 1045 static const struct net_device_ops ax88178_netdev_ops = { 1046 .ndo_open = usbnet_open, 1047 .ndo_stop = usbnet_stop, 1048 .ndo_start_xmit = usbnet_start_xmit, 1049 .ndo_tx_timeout = usbnet_tx_timeout, 1050 .ndo_set_mac_address = asix_set_mac_address, 1051 .ndo_validate_addr = eth_validate_addr, 1052 .ndo_set_rx_mode = asix_set_multicast, 1053 .ndo_do_ioctl = asix_ioctl, 1054 .ndo_change_mtu = ax88178_change_mtu, 1055 }; 1056 1057 static int ax88178_bind(struct usbnet *dev, struct usb_interface *intf) 1058 { 1059 int ret; 1060 u8 buf[ETH_ALEN]; 1061 1062 usbnet_get_endpoints(dev,intf); 1063 1064 /* Get the MAC address */ 1065 ret = asix_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf, 0); 1066 if (ret < 0) { 1067 netdev_dbg(dev->net, "Failed to read MAC address: %d\n", ret); 1068 return ret; 1069 } 1070 1071 asix_set_netdev_dev_addr(dev, buf); 1072 1073 /* Initialize MII structure */ 1074 dev->mii.dev = dev->net; 1075 dev->mii.mdio_read = asix_mdio_read; 1076 dev->mii.mdio_write = asix_mdio_write; 1077 dev->mii.phy_id_mask = 0x1f; 1078 dev->mii.reg_num_mask = 0xff; 1079 dev->mii.supports_gmii = 1; 1080 dev->mii.phy_id = asix_get_phy_addr(dev); 1081 1082 dev->net->netdev_ops = &ax88178_netdev_ops; 1083 dev->net->ethtool_ops = &ax88178_ethtool_ops; 1084 1085 /* Blink LEDS so users know driver saw dongle */ 1086 asix_sw_reset(dev, 0, 0); 1087 msleep(150); 1088 1089 asix_sw_reset(dev, AX_SWRESET_PRL | AX_SWRESET_IPPD, 0); 1090 msleep(150); 1091 1092 /* Asix framing packs multiple eth frames into a 2K usb bulk transfer */ 1093 if (dev->driver_info->flags & FLAG_FRAMING_AX) { 1094 /* hard_mtu is still the default - the device does not support 1095 jumbo eth frames */ 1096 dev->rx_urb_size = 2048; 1097 } 1098 1099 dev->driver_priv = kzalloc(sizeof(struct asix_common_private), GFP_KERNEL); 1100 if (!dev->driver_priv) 1101 return -ENOMEM; 1102 1103 return 0; 1104 } 1105 1106 static const struct driver_info ax8817x_info = { 1107 .description = "ASIX AX8817x USB 2.0 Ethernet", 1108 .bind = ax88172_bind, 1109 .status = asix_status, 1110 .link_reset = ax88172_link_reset, 1111 .reset = ax88172_link_reset, 1112 .flags = FLAG_ETHER | FLAG_LINK_INTR, 1113 .data = 0x00130103, 1114 }; 1115 1116 static const struct driver_info dlink_dub_e100_info = { 1117 .description = "DLink DUB-E100 USB Ethernet", 1118 .bind = ax88172_bind, 1119 .status = asix_status, 1120 .link_reset = ax88172_link_reset, 1121 .reset = ax88172_link_reset, 1122 .flags = FLAG_ETHER | FLAG_LINK_INTR, 1123 .data = 0x009f9d9f, 1124 }; 1125 1126 static const struct driver_info netgear_fa120_info = { 1127 .description = "Netgear FA-120 USB Ethernet", 1128 .bind = ax88172_bind, 1129 .status = asix_status, 1130 .link_reset = ax88172_link_reset, 1131 .reset = ax88172_link_reset, 1132 .flags = FLAG_ETHER | FLAG_LINK_INTR, 1133 .data = 0x00130103, 1134 }; 1135 1136 static const struct driver_info hawking_uf200_info = { 1137 .description = "Hawking UF200 USB Ethernet", 1138 .bind = ax88172_bind, 1139 .status = asix_status, 1140 .link_reset = ax88172_link_reset, 1141 .reset = ax88172_link_reset, 1142 .flags = FLAG_ETHER | FLAG_LINK_INTR, 1143 .data = 0x001f1d1f, 1144 }; 1145 1146 static const struct driver_info ax88772_info = { 1147 .description = "ASIX AX88772 USB 2.0 Ethernet", 1148 .bind = ax88772_bind, 1149 .unbind = ax88772_unbind, 1150 .status = asix_status, 1151 .link_reset = ax88772_link_reset, 1152 .reset = ax88772_reset, 1153 .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR | FLAG_MULTI_PACKET, 1154 .rx_fixup = asix_rx_fixup_common, 1155 .tx_fixup = asix_tx_fixup, 1156 }; 1157 1158 static const struct driver_info ax88772b_info = { 1159 .description = "ASIX AX88772B USB 2.0 Ethernet", 1160 .bind = ax88772_bind, 1161 .unbind = ax88772_unbind, 1162 .status = asix_status, 1163 .link_reset = ax88772_link_reset, 1164 .reset = ax88772_reset, 1165 .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR | 1166 FLAG_MULTI_PACKET, 1167 .rx_fixup = asix_rx_fixup_common, 1168 .tx_fixup = asix_tx_fixup, 1169 .data = FLAG_EEPROM_MAC, 1170 }; 1171 1172 static const struct driver_info ax88178_info = { 1173 .description = "ASIX AX88178 USB 2.0 Ethernet", 1174 .bind = ax88178_bind, 1175 .unbind = ax88772_unbind, 1176 .status = asix_status, 1177 .link_reset = ax88178_link_reset, 1178 .reset = ax88178_reset, 1179 .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR | 1180 FLAG_MULTI_PACKET, 1181 .rx_fixup = asix_rx_fixup_common, 1182 .tx_fixup = asix_tx_fixup, 1183 }; 1184 1185 /* 1186 * USBLINK 20F9 "USB 2.0 LAN" USB ethernet adapter, typically found in 1187 * no-name packaging. 1188 * USB device strings are: 1189 * 1: Manufacturer: USBLINK 1190 * 2: Product: HG20F9 USB2.0 1191 * 3: Serial: 000003 1192 * Appears to be compatible with Asix 88772B. 1193 */ 1194 static const struct driver_info hg20f9_info = { 1195 .description = "HG20F9 USB 2.0 Ethernet", 1196 .bind = ax88772_bind, 1197 .unbind = ax88772_unbind, 1198 .status = asix_status, 1199 .link_reset = ax88772_link_reset, 1200 .reset = ax88772_reset, 1201 .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR | 1202 FLAG_MULTI_PACKET, 1203 .rx_fixup = asix_rx_fixup_common, 1204 .tx_fixup = asix_tx_fixup, 1205 .data = FLAG_EEPROM_MAC, 1206 }; 1207 1208 static const struct usb_device_id products [] = { 1209 { 1210 // Linksys USB200M 1211 USB_DEVICE (0x077b, 0x2226), 1212 .driver_info = (unsigned long) &ax8817x_info, 1213 }, { 1214 // Netgear FA120 1215 USB_DEVICE (0x0846, 0x1040), 1216 .driver_info = (unsigned long) &netgear_fa120_info, 1217 }, { 1218 // DLink DUB-E100 1219 USB_DEVICE (0x2001, 0x1a00), 1220 .driver_info = (unsigned long) &dlink_dub_e100_info, 1221 }, { 1222 // Intellinet, ST Lab USB Ethernet 1223 USB_DEVICE (0x0b95, 0x1720), 1224 .driver_info = (unsigned long) &ax8817x_info, 1225 }, { 1226 // Hawking UF200, TrendNet TU2-ET100 1227 USB_DEVICE (0x07b8, 0x420a), 1228 .driver_info = (unsigned long) &hawking_uf200_info, 1229 }, { 1230 // Billionton Systems, USB2AR 1231 USB_DEVICE (0x08dd, 0x90ff), 1232 .driver_info = (unsigned long) &ax8817x_info, 1233 }, { 1234 // Billionton Systems, GUSB2AM-1G-B 1235 USB_DEVICE(0x08dd, 0x0114), 1236 .driver_info = (unsigned long) &ax88178_info, 1237 }, { 1238 // ATEN UC210T 1239 USB_DEVICE (0x0557, 0x2009), 1240 .driver_info = (unsigned long) &ax8817x_info, 1241 }, { 1242 // Buffalo LUA-U2-KTX 1243 USB_DEVICE (0x0411, 0x003d), 1244 .driver_info = (unsigned long) &ax8817x_info, 1245 }, { 1246 // Buffalo LUA-U2-GT 10/100/1000 1247 USB_DEVICE (0x0411, 0x006e), 1248 .driver_info = (unsigned long) &ax88178_info, 1249 }, { 1250 // Sitecom LN-029 "USB 2.0 10/100 Ethernet adapter" 1251 USB_DEVICE (0x6189, 0x182d), 1252 .driver_info = (unsigned long) &ax8817x_info, 1253 }, { 1254 // Sitecom LN-031 "USB 2.0 10/100/1000 Ethernet adapter" 1255 USB_DEVICE (0x0df6, 0x0056), 1256 .driver_info = (unsigned long) &ax88178_info, 1257 }, { 1258 // Sitecom LN-028 "USB 2.0 10/100/1000 Ethernet adapter" 1259 USB_DEVICE (0x0df6, 0x061c), 1260 .driver_info = (unsigned long) &ax88178_info, 1261 }, { 1262 // corega FEther USB2-TX 1263 USB_DEVICE (0x07aa, 0x0017), 1264 .driver_info = (unsigned long) &ax8817x_info, 1265 }, { 1266 // Surecom EP-1427X-2 1267 USB_DEVICE (0x1189, 0x0893), 1268 .driver_info = (unsigned long) &ax8817x_info, 1269 }, { 1270 // goodway corp usb gwusb2e 1271 USB_DEVICE (0x1631, 0x6200), 1272 .driver_info = (unsigned long) &ax8817x_info, 1273 }, { 1274 // JVC MP-PRX1 Port Replicator 1275 USB_DEVICE (0x04f1, 0x3008), 1276 .driver_info = (unsigned long) &ax8817x_info, 1277 }, { 1278 // Lenovo U2L100P 10/100 1279 USB_DEVICE (0x17ef, 0x7203), 1280 .driver_info = (unsigned long)&ax88772b_info, 1281 }, { 1282 // ASIX AX88772B 10/100 1283 USB_DEVICE (0x0b95, 0x772b), 1284 .driver_info = (unsigned long) &ax88772b_info, 1285 }, { 1286 // ASIX AX88772 10/100 1287 USB_DEVICE (0x0b95, 0x7720), 1288 .driver_info = (unsigned long) &ax88772_info, 1289 }, { 1290 // ASIX AX88178 10/100/1000 1291 USB_DEVICE (0x0b95, 0x1780), 1292 .driver_info = (unsigned long) &ax88178_info, 1293 }, { 1294 // Logitec LAN-GTJ/U2A 1295 USB_DEVICE (0x0789, 0x0160), 1296 .driver_info = (unsigned long) &ax88178_info, 1297 }, { 1298 // Linksys USB200M Rev 2 1299 USB_DEVICE (0x13b1, 0x0018), 1300 .driver_info = (unsigned long) &ax88772_info, 1301 }, { 1302 // 0Q0 cable ethernet 1303 USB_DEVICE (0x1557, 0x7720), 1304 .driver_info = (unsigned long) &ax88772_info, 1305 }, { 1306 // DLink DUB-E100 H/W Ver B1 1307 USB_DEVICE (0x07d1, 0x3c05), 1308 .driver_info = (unsigned long) &ax88772_info, 1309 }, { 1310 // DLink DUB-E100 H/W Ver B1 Alternate 1311 USB_DEVICE (0x2001, 0x3c05), 1312 .driver_info = (unsigned long) &ax88772_info, 1313 }, { 1314 // DLink DUB-E100 H/W Ver C1 1315 USB_DEVICE (0x2001, 0x1a02), 1316 .driver_info = (unsigned long) &ax88772_info, 1317 }, { 1318 // Linksys USB1000 1319 USB_DEVICE (0x1737, 0x0039), 1320 .driver_info = (unsigned long) &ax88178_info, 1321 }, { 1322 // IO-DATA ETG-US2 1323 USB_DEVICE (0x04bb, 0x0930), 1324 .driver_info = (unsigned long) &ax88178_info, 1325 }, { 1326 // Belkin F5D5055 1327 USB_DEVICE(0x050d, 0x5055), 1328 .driver_info = (unsigned long) &ax88178_info, 1329 }, { 1330 // Apple USB Ethernet Adapter 1331 USB_DEVICE(0x05ac, 0x1402), 1332 .driver_info = (unsigned long) &ax88772_info, 1333 }, { 1334 // Cables-to-Go USB Ethernet Adapter 1335 USB_DEVICE(0x0b95, 0x772a), 1336 .driver_info = (unsigned long) &ax88772_info, 1337 }, { 1338 // ABOCOM for pci 1339 USB_DEVICE(0x14ea, 0xab11), 1340 .driver_info = (unsigned long) &ax88178_info, 1341 }, { 1342 // ASIX 88772a 1343 USB_DEVICE(0x0db0, 0xa877), 1344 .driver_info = (unsigned long) &ax88772_info, 1345 }, { 1346 // Asus USB Ethernet Adapter 1347 USB_DEVICE (0x0b95, 0x7e2b), 1348 .driver_info = (unsigned long)&ax88772b_info, 1349 }, { 1350 /* ASIX 88172a demo board */ 1351 USB_DEVICE(0x0b95, 0x172a), 1352 .driver_info = (unsigned long) &ax88172a_info, 1353 }, { 1354 /* 1355 * USBLINK HG20F9 "USB 2.0 LAN" 1356 * Appears to have gazumped Linksys's manufacturer ID but 1357 * doesn't (yet) conflict with any known Linksys product. 1358 */ 1359 USB_DEVICE(0x066b, 0x20f9), 1360 .driver_info = (unsigned long) &hg20f9_info, 1361 }, 1362 { }, // END 1363 }; 1364 MODULE_DEVICE_TABLE(usb, products); 1365 1366 static struct usb_driver asix_driver = { 1367 .name = DRIVER_NAME, 1368 .id_table = products, 1369 .probe = usbnet_probe, 1370 .suspend = asix_suspend, 1371 .resume = asix_resume, 1372 .disconnect = usbnet_disconnect, 1373 .supports_autosuspend = 1, 1374 .disable_hub_initiated_lpm = 1, 1375 }; 1376 1377 module_usb_driver(asix_driver); 1378 1379 MODULE_AUTHOR("David Hollis"); 1380 MODULE_VERSION(DRIVER_VERSION); 1381 MODULE_DESCRIPTION("ASIX AX8817X based USB 2.0 Ethernet Devices"); 1382 MODULE_LICENSE("GPL"); 1383 1384