1 // SPDX-License-Identifier: GPL-2.0+ 2 /* Copyright (C) 2021 Maxlinear Corporation 3 * Copyright (C) 2020 Intel Corporation 4 * 5 * Drivers for Maxlinear Ethernet GPY 6 * 7 */ 8 9 #include <linux/module.h> 10 #include <linux/bitfield.h> 11 #include <linux/phy.h> 12 #include <linux/netdevice.h> 13 14 /* PHY ID */ 15 #define PHY_ID_GPYx15B_MASK 0xFFFFFFFC 16 #define PHY_ID_GPY21xB_MASK 0xFFFFFFF9 17 #define PHY_ID_GPY2xx 0x67C9DC00 18 #define PHY_ID_GPY115B 0x67C9DF00 19 #define PHY_ID_GPY115C 0x67C9DF10 20 #define PHY_ID_GPY211B 0x67C9DE08 21 #define PHY_ID_GPY211C 0x67C9DE10 22 #define PHY_ID_GPY212B 0x67C9DE09 23 #define PHY_ID_GPY212C 0x67C9DE20 24 #define PHY_ID_GPY215B 0x67C9DF04 25 #define PHY_ID_GPY215C 0x67C9DF20 26 #define PHY_ID_GPY241B 0x67C9DE40 27 #define PHY_ID_GPY241BM 0x67C9DE80 28 #define PHY_ID_GPY245B 0x67C9DEC0 29 30 #define PHY_MIISTAT 0x18 /* MII state */ 31 #define PHY_IMASK 0x19 /* interrupt mask */ 32 #define PHY_ISTAT 0x1A /* interrupt status */ 33 #define PHY_FWV 0x1E /* firmware version */ 34 35 #define PHY_MIISTAT_SPD_MASK GENMASK(2, 0) 36 #define PHY_MIISTAT_DPX BIT(3) 37 #define PHY_MIISTAT_LS BIT(10) 38 39 #define PHY_MIISTAT_SPD_10 0 40 #define PHY_MIISTAT_SPD_100 1 41 #define PHY_MIISTAT_SPD_1000 2 42 #define PHY_MIISTAT_SPD_2500 4 43 44 #define PHY_IMASK_WOL BIT(15) /* Wake-on-LAN */ 45 #define PHY_IMASK_ANC BIT(10) /* Auto-Neg complete */ 46 #define PHY_IMASK_ADSC BIT(5) /* Link auto-downspeed detect */ 47 #define PHY_IMASK_DXMC BIT(2) /* Duplex mode change */ 48 #define PHY_IMASK_LSPC BIT(1) /* Link speed change */ 49 #define PHY_IMASK_LSTC BIT(0) /* Link state change */ 50 #define PHY_IMASK_MASK (PHY_IMASK_LSTC | \ 51 PHY_IMASK_LSPC | \ 52 PHY_IMASK_DXMC | \ 53 PHY_IMASK_ADSC | \ 54 PHY_IMASK_ANC) 55 56 #define PHY_FWV_REL_MASK BIT(15) 57 #define PHY_FWV_TYPE_MASK GENMASK(11, 8) 58 #define PHY_FWV_MINOR_MASK GENMASK(7, 0) 59 60 /* SGMII */ 61 #define VSPEC1_SGMII_CTRL 0x08 62 #define VSPEC1_SGMII_CTRL_ANEN BIT(12) /* Aneg enable */ 63 #define VSPEC1_SGMII_CTRL_ANRS BIT(9) /* Restart Aneg */ 64 #define VSPEC1_SGMII_ANEN_ANRS (VSPEC1_SGMII_CTRL_ANEN | \ 65 VSPEC1_SGMII_CTRL_ANRS) 66 67 /* WoL */ 68 #define VPSPEC2_WOL_CTL 0x0E06 69 #define VPSPEC2_WOL_AD01 0x0E08 70 #define VPSPEC2_WOL_AD23 0x0E09 71 #define VPSPEC2_WOL_AD45 0x0E0A 72 #define WOL_EN BIT(0) 73 74 static const struct { 75 int type; 76 int minor; 77 } ver_need_sgmii_reaneg[] = { 78 {7, 0x6D}, 79 {8, 0x6D}, 80 {9, 0x73}, 81 }; 82 83 static int gpy_config_init(struct phy_device *phydev) 84 { 85 int ret; 86 87 /* Mask all interrupts */ 88 ret = phy_write(phydev, PHY_IMASK, 0); 89 if (ret) 90 return ret; 91 92 /* Clear all pending interrupts */ 93 ret = phy_read(phydev, PHY_ISTAT); 94 return ret < 0 ? ret : 0; 95 } 96 97 static int gpy_probe(struct phy_device *phydev) 98 { 99 int ret; 100 101 if (!phydev->is_c45) { 102 ret = phy_get_c45_ids(phydev); 103 if (ret < 0) 104 return ret; 105 } 106 107 /* Show GPY PHY FW version in dmesg */ 108 ret = phy_read(phydev, PHY_FWV); 109 if (ret < 0) 110 return ret; 111 112 phydev_info(phydev, "Firmware Version: 0x%04X (%s)\n", ret, 113 (ret & PHY_FWV_REL_MASK) ? "release" : "test"); 114 115 return 0; 116 } 117 118 static bool gpy_sgmii_need_reaneg(struct phy_device *phydev) 119 { 120 int fw_ver, fw_type, fw_minor; 121 size_t i; 122 123 fw_ver = phy_read(phydev, PHY_FWV); 124 if (fw_ver < 0) 125 return true; 126 127 fw_type = FIELD_GET(PHY_FWV_TYPE_MASK, fw_ver); 128 fw_minor = FIELD_GET(PHY_FWV_MINOR_MASK, fw_ver); 129 130 for (i = 0; i < ARRAY_SIZE(ver_need_sgmii_reaneg); i++) { 131 if (fw_type != ver_need_sgmii_reaneg[i].type) 132 continue; 133 if (fw_minor < ver_need_sgmii_reaneg[i].minor) 134 return true; 135 break; 136 } 137 138 return false; 139 } 140 141 static bool gpy_2500basex_chk(struct phy_device *phydev) 142 { 143 int ret; 144 145 ret = phy_read(phydev, PHY_MIISTAT); 146 if (ret < 0) { 147 phydev_err(phydev, "Error: MDIO register access failed: %d\n", 148 ret); 149 return false; 150 } 151 152 if (!(ret & PHY_MIISTAT_LS) || 153 FIELD_GET(PHY_MIISTAT_SPD_MASK, ret) != PHY_MIISTAT_SPD_2500) 154 return false; 155 156 phydev->speed = SPEED_2500; 157 phydev->interface = PHY_INTERFACE_MODE_2500BASEX; 158 phy_modify_mmd(phydev, MDIO_MMD_VEND1, VSPEC1_SGMII_CTRL, 159 VSPEC1_SGMII_CTRL_ANEN, 0); 160 return true; 161 } 162 163 static bool gpy_sgmii_aneg_en(struct phy_device *phydev) 164 { 165 int ret; 166 167 ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, VSPEC1_SGMII_CTRL); 168 if (ret < 0) { 169 phydev_err(phydev, "Error: MMD register access failed: %d\n", 170 ret); 171 return true; 172 } 173 174 return (ret & VSPEC1_SGMII_CTRL_ANEN) ? true : false; 175 } 176 177 static int gpy_config_aneg(struct phy_device *phydev) 178 { 179 bool changed = false; 180 u32 adv; 181 int ret; 182 183 if (phydev->autoneg == AUTONEG_DISABLE) { 184 /* Configure half duplex with genphy_setup_forced, 185 * because genphy_c45_pma_setup_forced does not support. 186 */ 187 return phydev->duplex != DUPLEX_FULL 188 ? genphy_setup_forced(phydev) 189 : genphy_c45_pma_setup_forced(phydev); 190 } 191 192 ret = genphy_c45_an_config_aneg(phydev); 193 if (ret < 0) 194 return ret; 195 if (ret > 0) 196 changed = true; 197 198 adv = linkmode_adv_to_mii_ctrl1000_t(phydev->advertising); 199 ret = phy_modify_changed(phydev, MII_CTRL1000, 200 ADVERTISE_1000FULL | ADVERTISE_1000HALF, 201 adv); 202 if (ret < 0) 203 return ret; 204 if (ret > 0) 205 changed = true; 206 207 ret = genphy_c45_check_and_restart_aneg(phydev, changed); 208 if (ret < 0) 209 return ret; 210 211 if (phydev->interface == PHY_INTERFACE_MODE_USXGMII || 212 phydev->interface == PHY_INTERFACE_MODE_INTERNAL) 213 return 0; 214 215 /* No need to trigger re-ANEG if link speed is 2.5G or SGMII ANEG is 216 * disabled. 217 */ 218 if (!gpy_sgmii_need_reaneg(phydev) || gpy_2500basex_chk(phydev) || 219 !gpy_sgmii_aneg_en(phydev)) 220 return 0; 221 222 /* There is a design constraint in GPY2xx device where SGMII AN is 223 * only triggered when there is change of speed. If, PHY link 224 * partner`s speed is still same even after PHY TPI is down and up 225 * again, SGMII AN is not triggered and hence no new in-band message 226 * from GPY to MAC side SGMII. 227 * This could cause an issue during power up, when PHY is up prior to 228 * MAC. At this condition, once MAC side SGMII is up, MAC side SGMII 229 * wouldn`t receive new in-band message from GPY with correct link 230 * status, speed and duplex info. 231 * 232 * 1) If PHY is already up and TPI link status is still down (such as 233 * hard reboot), TPI link status is polled for 4 seconds before 234 * retriggerring SGMII AN. 235 * 2) If PHY is already up and TPI link status is also up (such as soft 236 * reboot), polling of TPI link status is not needed and SGMII AN is 237 * immediately retriggered. 238 * 3) Other conditions such as PHY is down, speed change etc, skip 239 * retriggering SGMII AN. Note: in case of speed change, GPY FW will 240 * initiate SGMII AN. 241 */ 242 243 if (phydev->state != PHY_UP) 244 return 0; 245 246 ret = phy_read_poll_timeout(phydev, MII_BMSR, ret, ret & BMSR_LSTATUS, 247 20000, 4000000, false); 248 if (ret == -ETIMEDOUT) 249 return 0; 250 else if (ret < 0) 251 return ret; 252 253 /* Trigger SGMII AN. */ 254 return phy_modify_mmd(phydev, MDIO_MMD_VEND1, VSPEC1_SGMII_CTRL, 255 VSPEC1_SGMII_CTRL_ANRS, VSPEC1_SGMII_CTRL_ANRS); 256 } 257 258 static void gpy_update_interface(struct phy_device *phydev) 259 { 260 int ret; 261 262 /* Interface mode is fixed for USXGMII and integrated PHY */ 263 if (phydev->interface == PHY_INTERFACE_MODE_USXGMII || 264 phydev->interface == PHY_INTERFACE_MODE_INTERNAL) 265 return; 266 267 /* Automatically switch SERDES interface between SGMII and 2500-BaseX 268 * according to speed. Disable ANEG in 2500-BaseX mode. 269 */ 270 switch (phydev->speed) { 271 case SPEED_2500: 272 phydev->interface = PHY_INTERFACE_MODE_2500BASEX; 273 ret = phy_modify_mmd(phydev, MDIO_MMD_VEND1, VSPEC1_SGMII_CTRL, 274 VSPEC1_SGMII_CTRL_ANEN, 0); 275 if (ret < 0) 276 phydev_err(phydev, 277 "Error: Disable of SGMII ANEG failed: %d\n", 278 ret); 279 break; 280 case SPEED_1000: 281 case SPEED_100: 282 case SPEED_10: 283 phydev->interface = PHY_INTERFACE_MODE_SGMII; 284 if (gpy_sgmii_aneg_en(phydev)) 285 break; 286 /* Enable and restart SGMII ANEG for 10/100/1000Mbps link speed 287 * if ANEG is disabled (in 2500-BaseX mode). 288 */ 289 ret = phy_modify_mmd(phydev, MDIO_MMD_VEND1, VSPEC1_SGMII_CTRL, 290 VSPEC1_SGMII_ANEN_ANRS, 291 VSPEC1_SGMII_ANEN_ANRS); 292 if (ret < 0) 293 phydev_err(phydev, 294 "Error: Enable of SGMII ANEG failed: %d\n", 295 ret); 296 break; 297 } 298 } 299 300 static int gpy_read_status(struct phy_device *phydev) 301 { 302 int ret; 303 304 ret = genphy_update_link(phydev); 305 if (ret) 306 return ret; 307 308 phydev->speed = SPEED_UNKNOWN; 309 phydev->duplex = DUPLEX_UNKNOWN; 310 phydev->pause = 0; 311 phydev->asym_pause = 0; 312 313 if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete) { 314 ret = genphy_c45_read_lpa(phydev); 315 if (ret < 0) 316 return ret; 317 318 /* Read the link partner's 1G advertisement */ 319 ret = phy_read(phydev, MII_STAT1000); 320 if (ret < 0) 321 return ret; 322 mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising, ret); 323 } else if (phydev->autoneg == AUTONEG_DISABLE) { 324 linkmode_zero(phydev->lp_advertising); 325 } 326 327 ret = phy_read(phydev, PHY_MIISTAT); 328 if (ret < 0) 329 return ret; 330 331 phydev->link = (ret & PHY_MIISTAT_LS) ? 1 : 0; 332 phydev->duplex = (ret & PHY_MIISTAT_DPX) ? DUPLEX_FULL : DUPLEX_HALF; 333 switch (FIELD_GET(PHY_MIISTAT_SPD_MASK, ret)) { 334 case PHY_MIISTAT_SPD_10: 335 phydev->speed = SPEED_10; 336 break; 337 case PHY_MIISTAT_SPD_100: 338 phydev->speed = SPEED_100; 339 break; 340 case PHY_MIISTAT_SPD_1000: 341 phydev->speed = SPEED_1000; 342 break; 343 case PHY_MIISTAT_SPD_2500: 344 phydev->speed = SPEED_2500; 345 break; 346 } 347 348 if (phydev->link) 349 gpy_update_interface(phydev); 350 351 return 0; 352 } 353 354 static int gpy_config_intr(struct phy_device *phydev) 355 { 356 u16 mask = 0; 357 358 if (phydev->interrupts == PHY_INTERRUPT_ENABLED) 359 mask = PHY_IMASK_MASK; 360 361 return phy_write(phydev, PHY_IMASK, mask); 362 } 363 364 static irqreturn_t gpy_handle_interrupt(struct phy_device *phydev) 365 { 366 int reg; 367 368 reg = phy_read(phydev, PHY_ISTAT); 369 if (reg < 0) { 370 phy_error(phydev); 371 return IRQ_NONE; 372 } 373 374 if (!(reg & PHY_IMASK_MASK)) 375 return IRQ_NONE; 376 377 phy_trigger_machine(phydev); 378 379 return IRQ_HANDLED; 380 } 381 382 static int gpy_set_wol(struct phy_device *phydev, 383 struct ethtool_wolinfo *wol) 384 { 385 struct net_device *attach_dev = phydev->attached_dev; 386 int ret; 387 388 if (wol->wolopts & WAKE_MAGIC) { 389 /* MAC address - Byte0:Byte1:Byte2:Byte3:Byte4:Byte5 390 * VPSPEC2_WOL_AD45 = Byte0:Byte1 391 * VPSPEC2_WOL_AD23 = Byte2:Byte3 392 * VPSPEC2_WOL_AD01 = Byte4:Byte5 393 */ 394 ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, 395 VPSPEC2_WOL_AD45, 396 ((attach_dev->dev_addr[0] << 8) | 397 attach_dev->dev_addr[1])); 398 if (ret < 0) 399 return ret; 400 401 ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, 402 VPSPEC2_WOL_AD23, 403 ((attach_dev->dev_addr[2] << 8) | 404 attach_dev->dev_addr[3])); 405 if (ret < 0) 406 return ret; 407 408 ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, 409 VPSPEC2_WOL_AD01, 410 ((attach_dev->dev_addr[4] << 8) | 411 attach_dev->dev_addr[5])); 412 if (ret < 0) 413 return ret; 414 415 /* Enable the WOL interrupt */ 416 ret = phy_write(phydev, PHY_IMASK, PHY_IMASK_WOL); 417 if (ret < 0) 418 return ret; 419 420 /* Enable magic packet matching */ 421 ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, 422 VPSPEC2_WOL_CTL, 423 WOL_EN); 424 if (ret < 0) 425 return ret; 426 427 /* Clear the interrupt status register. 428 * Only WoL is enabled so clear all. 429 */ 430 ret = phy_read(phydev, PHY_ISTAT); 431 if (ret < 0) 432 return ret; 433 } else { 434 /* Disable magic packet matching */ 435 ret = phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2, 436 VPSPEC2_WOL_CTL, 437 WOL_EN); 438 if (ret < 0) 439 return ret; 440 } 441 442 if (wol->wolopts & WAKE_PHY) { 443 /* Enable the link state change interrupt */ 444 ret = phy_set_bits(phydev, PHY_IMASK, PHY_IMASK_LSTC); 445 if (ret < 0) 446 return ret; 447 448 /* Clear the interrupt status register */ 449 ret = phy_read(phydev, PHY_ISTAT); 450 if (ret < 0) 451 return ret; 452 453 if (ret & (PHY_IMASK_MASK & ~PHY_IMASK_LSTC)) 454 phy_trigger_machine(phydev); 455 456 return 0; 457 } 458 459 /* Disable the link state change interrupt */ 460 return phy_clear_bits(phydev, PHY_IMASK, PHY_IMASK_LSTC); 461 } 462 463 static void gpy_get_wol(struct phy_device *phydev, 464 struct ethtool_wolinfo *wol) 465 { 466 int ret; 467 468 wol->supported = WAKE_MAGIC | WAKE_PHY; 469 wol->wolopts = 0; 470 471 ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, VPSPEC2_WOL_CTL); 472 if (ret & WOL_EN) 473 wol->wolopts |= WAKE_MAGIC; 474 475 ret = phy_read(phydev, PHY_IMASK); 476 if (ret & PHY_IMASK_LSTC) 477 wol->wolopts |= WAKE_PHY; 478 } 479 480 static int gpy_loopback(struct phy_device *phydev, bool enable) 481 { 482 int ret; 483 484 ret = phy_modify(phydev, MII_BMCR, BMCR_LOOPBACK, 485 enable ? BMCR_LOOPBACK : 0); 486 if (!ret) { 487 /* It takes some time for PHY device to switch 488 * into/out-of loopback mode. 489 */ 490 msleep(100); 491 } 492 493 return ret; 494 } 495 496 static struct phy_driver gpy_drivers[] = { 497 { 498 PHY_ID_MATCH_MODEL(PHY_ID_GPY2xx), 499 .name = "Maxlinear Ethernet GPY2xx", 500 .get_features = genphy_c45_pma_read_abilities, 501 .config_init = gpy_config_init, 502 .probe = gpy_probe, 503 .suspend = genphy_suspend, 504 .resume = genphy_resume, 505 .config_aneg = gpy_config_aneg, 506 .aneg_done = genphy_c45_aneg_done, 507 .read_status = gpy_read_status, 508 .config_intr = gpy_config_intr, 509 .handle_interrupt = gpy_handle_interrupt, 510 .set_wol = gpy_set_wol, 511 .get_wol = gpy_get_wol, 512 .set_loopback = gpy_loopback, 513 }, 514 { 515 .phy_id = PHY_ID_GPY115B, 516 .phy_id_mask = PHY_ID_GPYx15B_MASK, 517 .name = "Maxlinear Ethernet GPY115B", 518 .get_features = genphy_c45_pma_read_abilities, 519 .config_init = gpy_config_init, 520 .probe = gpy_probe, 521 .suspend = genphy_suspend, 522 .resume = genphy_resume, 523 .config_aneg = gpy_config_aneg, 524 .aneg_done = genphy_c45_aneg_done, 525 .read_status = gpy_read_status, 526 .config_intr = gpy_config_intr, 527 .handle_interrupt = gpy_handle_interrupt, 528 .set_wol = gpy_set_wol, 529 .get_wol = gpy_get_wol, 530 .set_loopback = gpy_loopback, 531 }, 532 { 533 PHY_ID_MATCH_MODEL(PHY_ID_GPY115C), 534 .name = "Maxlinear Ethernet GPY115C", 535 .get_features = genphy_c45_pma_read_abilities, 536 .config_init = gpy_config_init, 537 .probe = gpy_probe, 538 .suspend = genphy_suspend, 539 .resume = genphy_resume, 540 .config_aneg = gpy_config_aneg, 541 .aneg_done = genphy_c45_aneg_done, 542 .read_status = gpy_read_status, 543 .config_intr = gpy_config_intr, 544 .handle_interrupt = gpy_handle_interrupt, 545 .set_wol = gpy_set_wol, 546 .get_wol = gpy_get_wol, 547 .set_loopback = gpy_loopback, 548 }, 549 { 550 .phy_id = PHY_ID_GPY211B, 551 .phy_id_mask = PHY_ID_GPY21xB_MASK, 552 .name = "Maxlinear Ethernet GPY211B", 553 .get_features = genphy_c45_pma_read_abilities, 554 .config_init = gpy_config_init, 555 .probe = gpy_probe, 556 .suspend = genphy_suspend, 557 .resume = genphy_resume, 558 .config_aneg = gpy_config_aneg, 559 .aneg_done = genphy_c45_aneg_done, 560 .read_status = gpy_read_status, 561 .config_intr = gpy_config_intr, 562 .handle_interrupt = gpy_handle_interrupt, 563 .set_wol = gpy_set_wol, 564 .get_wol = gpy_get_wol, 565 .set_loopback = gpy_loopback, 566 }, 567 { 568 PHY_ID_MATCH_MODEL(PHY_ID_GPY211C), 569 .name = "Maxlinear Ethernet GPY211C", 570 .get_features = genphy_c45_pma_read_abilities, 571 .config_init = gpy_config_init, 572 .probe = gpy_probe, 573 .suspend = genphy_suspend, 574 .resume = genphy_resume, 575 .config_aneg = gpy_config_aneg, 576 .aneg_done = genphy_c45_aneg_done, 577 .read_status = gpy_read_status, 578 .config_intr = gpy_config_intr, 579 .handle_interrupt = gpy_handle_interrupt, 580 .set_wol = gpy_set_wol, 581 .get_wol = gpy_get_wol, 582 .set_loopback = gpy_loopback, 583 }, 584 { 585 .phy_id = PHY_ID_GPY212B, 586 .phy_id_mask = PHY_ID_GPY21xB_MASK, 587 .name = "Maxlinear Ethernet GPY212B", 588 .get_features = genphy_c45_pma_read_abilities, 589 .config_init = gpy_config_init, 590 .probe = gpy_probe, 591 .suspend = genphy_suspend, 592 .resume = genphy_resume, 593 .config_aneg = gpy_config_aneg, 594 .aneg_done = genphy_c45_aneg_done, 595 .read_status = gpy_read_status, 596 .config_intr = gpy_config_intr, 597 .handle_interrupt = gpy_handle_interrupt, 598 .set_wol = gpy_set_wol, 599 .get_wol = gpy_get_wol, 600 .set_loopback = gpy_loopback, 601 }, 602 { 603 PHY_ID_MATCH_MODEL(PHY_ID_GPY212C), 604 .name = "Maxlinear Ethernet GPY212C", 605 .get_features = genphy_c45_pma_read_abilities, 606 .config_init = gpy_config_init, 607 .probe = gpy_probe, 608 .suspend = genphy_suspend, 609 .resume = genphy_resume, 610 .config_aneg = gpy_config_aneg, 611 .aneg_done = genphy_c45_aneg_done, 612 .read_status = gpy_read_status, 613 .config_intr = gpy_config_intr, 614 .handle_interrupt = gpy_handle_interrupt, 615 .set_wol = gpy_set_wol, 616 .get_wol = gpy_get_wol, 617 .set_loopback = gpy_loopback, 618 }, 619 { 620 .phy_id = PHY_ID_GPY215B, 621 .phy_id_mask = PHY_ID_GPYx15B_MASK, 622 .name = "Maxlinear Ethernet GPY215B", 623 .get_features = genphy_c45_pma_read_abilities, 624 .config_init = gpy_config_init, 625 .probe = gpy_probe, 626 .suspend = genphy_suspend, 627 .resume = genphy_resume, 628 .config_aneg = gpy_config_aneg, 629 .aneg_done = genphy_c45_aneg_done, 630 .read_status = gpy_read_status, 631 .config_intr = gpy_config_intr, 632 .handle_interrupt = gpy_handle_interrupt, 633 .set_wol = gpy_set_wol, 634 .get_wol = gpy_get_wol, 635 .set_loopback = gpy_loopback, 636 }, 637 { 638 PHY_ID_MATCH_MODEL(PHY_ID_GPY215C), 639 .name = "Maxlinear Ethernet GPY215C", 640 .get_features = genphy_c45_pma_read_abilities, 641 .config_init = gpy_config_init, 642 .probe = gpy_probe, 643 .suspend = genphy_suspend, 644 .resume = genphy_resume, 645 .config_aneg = gpy_config_aneg, 646 .aneg_done = genphy_c45_aneg_done, 647 .read_status = gpy_read_status, 648 .config_intr = gpy_config_intr, 649 .handle_interrupt = gpy_handle_interrupt, 650 .set_wol = gpy_set_wol, 651 .get_wol = gpy_get_wol, 652 .set_loopback = gpy_loopback, 653 }, 654 { 655 PHY_ID_MATCH_MODEL(PHY_ID_GPY241B), 656 .name = "Maxlinear Ethernet GPY241B", 657 .get_features = genphy_c45_pma_read_abilities, 658 .config_init = gpy_config_init, 659 .probe = gpy_probe, 660 .suspend = genphy_suspend, 661 .resume = genphy_resume, 662 .config_aneg = gpy_config_aneg, 663 .aneg_done = genphy_c45_aneg_done, 664 .read_status = gpy_read_status, 665 .config_intr = gpy_config_intr, 666 .handle_interrupt = gpy_handle_interrupt, 667 .set_wol = gpy_set_wol, 668 .get_wol = gpy_get_wol, 669 .set_loopback = gpy_loopback, 670 }, 671 { 672 PHY_ID_MATCH_MODEL(PHY_ID_GPY241BM), 673 .name = "Maxlinear Ethernet GPY241BM", 674 .get_features = genphy_c45_pma_read_abilities, 675 .config_init = gpy_config_init, 676 .probe = gpy_probe, 677 .suspend = genphy_suspend, 678 .resume = genphy_resume, 679 .config_aneg = gpy_config_aneg, 680 .aneg_done = genphy_c45_aneg_done, 681 .read_status = gpy_read_status, 682 .config_intr = gpy_config_intr, 683 .handle_interrupt = gpy_handle_interrupt, 684 .set_wol = gpy_set_wol, 685 .get_wol = gpy_get_wol, 686 .set_loopback = gpy_loopback, 687 }, 688 { 689 PHY_ID_MATCH_MODEL(PHY_ID_GPY245B), 690 .name = "Maxlinear Ethernet GPY245B", 691 .get_features = genphy_c45_pma_read_abilities, 692 .config_init = gpy_config_init, 693 .probe = gpy_probe, 694 .suspend = genphy_suspend, 695 .resume = genphy_resume, 696 .config_aneg = gpy_config_aneg, 697 .aneg_done = genphy_c45_aneg_done, 698 .read_status = gpy_read_status, 699 .config_intr = gpy_config_intr, 700 .handle_interrupt = gpy_handle_interrupt, 701 .set_wol = gpy_set_wol, 702 .get_wol = gpy_get_wol, 703 .set_loopback = gpy_loopback, 704 }, 705 }; 706 module_phy_driver(gpy_drivers); 707 708 static struct mdio_device_id __maybe_unused gpy_tbl[] = { 709 {PHY_ID_MATCH_MODEL(PHY_ID_GPY2xx)}, 710 {PHY_ID_GPY115B, PHY_ID_GPYx15B_MASK}, 711 {PHY_ID_MATCH_MODEL(PHY_ID_GPY115C)}, 712 {PHY_ID_GPY211B, PHY_ID_GPY21xB_MASK}, 713 {PHY_ID_MATCH_MODEL(PHY_ID_GPY211C)}, 714 {PHY_ID_GPY212B, PHY_ID_GPY21xB_MASK}, 715 {PHY_ID_MATCH_MODEL(PHY_ID_GPY212C)}, 716 {PHY_ID_GPY215B, PHY_ID_GPYx15B_MASK}, 717 {PHY_ID_MATCH_MODEL(PHY_ID_GPY215C)}, 718 {PHY_ID_MATCH_MODEL(PHY_ID_GPY241B)}, 719 {PHY_ID_MATCH_MODEL(PHY_ID_GPY241BM)}, 720 {PHY_ID_MATCH_MODEL(PHY_ID_GPY245B)}, 721 { } 722 }; 723 MODULE_DEVICE_TABLE(mdio, gpy_tbl); 724 725 MODULE_DESCRIPTION("Maxlinear Ethernet GPY Driver"); 726 MODULE_AUTHOR("Xu Liang"); 727 MODULE_LICENSE("GPL"); 728