1 /* 2 * Tehuti Networks(R) Network Driver 3 * ethtool interface implementation 4 * Copyright (C) 2007 Tehuti Networks Ltd. All rights reserved 5 * 6 * This program is free software; you can redistribute it and/or modify 7 * it under the terms of the GNU General Public License as published by 8 * the Free Software Foundation; either version 2 of the License, or 9 * (at your option) any later version. 10 */ 11 12 /* 13 * RX HW/SW interaction overview 14 * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 15 * There are 2 types of RX communication channels between driver and NIC. 16 * 1) RX Free Fifo - RXF - holds descriptors of empty buffers to accept incoming 17 * traffic. This Fifo is filled by SW and is readen by HW. Each descriptor holds 18 * info about buffer's location, size and ID. An ID field is used to identify a 19 * buffer when it's returned with data via RXD Fifo (see below) 20 * 2) RX Data Fifo - RXD - holds descriptors of full buffers. This Fifo is 21 * filled by HW and is readen by SW. Each descriptor holds status and ID. 22 * HW pops descriptor from RXF Fifo, stores ID, fills buffer with incoming data, 23 * via dma moves it into host memory, builds new RXD descriptor with same ID, 24 * pushes it into RXD Fifo and raises interrupt to indicate new RX data. 25 * 26 * Current NIC configuration (registers + firmware) makes NIC use 2 RXF Fifos. 27 * One holds 1.5K packets and another - 26K packets. Depending on incoming 28 * packet size, HW desides on a RXF Fifo to pop buffer from. When packet is 29 * filled with data, HW builds new RXD descriptor for it and push it into single 30 * RXD Fifo. 31 * 32 * RX SW Data Structures 33 * ~~~~~~~~~~~~~~~~~~~~~ 34 * skb db - used to keep track of all skbs owned by SW and their dma addresses. 35 * For RX case, ownership lasts from allocating new empty skb for RXF until 36 * accepting full skb from RXD and passing it to OS. Each RXF Fifo has its own 37 * skb db. Implemented as array with bitmask. 38 * fifo - keeps info about fifo's size and location, relevant HW registers, 39 * usage and skb db. Each RXD and RXF Fifo has its own fifo structure. 40 * Implemented as simple struct. 41 * 42 * RX SW Execution Flow 43 * ~~~~~~~~~~~~~~~~~~~~ 44 * Upon initialization (ifconfig up) driver creates RX fifos and initializes 45 * relevant registers. At the end of init phase, driver enables interrupts. 46 * NIC sees that there is no RXF buffers and raises 47 * RD_INTR interrupt, isr fills skbs and Rx begins. 48 * Driver has two receive operation modes: 49 * NAPI - interrupt-driven mixed with polling 50 * interrupt-driven only 51 * 52 * Interrupt-driven only flow is following. When buffer is ready, HW raises 53 * interrupt and isr is called. isr collects all available packets 54 * (bdx_rx_receive), refills skbs (bdx_rx_alloc_skbs) and exit. 55 56 * Rx buffer allocation note 57 * ~~~~~~~~~~~~~~~~~~~~~~~~~ 58 * Driver cares to feed such amount of RxF descriptors that respective amount of 59 * RxD descriptors can not fill entire RxD fifo. The main reason is lack of 60 * overflow check in Bordeaux for RxD fifo free/used size. 61 * FIXME: this is NOT fully implemented, more work should be done 62 * 63 */ 64 65 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 66 67 #include "tehuti.h" 68 69 static const struct pci_device_id bdx_pci_tbl[] = { 70 { PCI_VDEVICE(TEHUTI, 0x3009), }, 71 { PCI_VDEVICE(TEHUTI, 0x3010), }, 72 { PCI_VDEVICE(TEHUTI, 0x3014), }, 73 { 0 } 74 }; 75 76 MODULE_DEVICE_TABLE(pci, bdx_pci_tbl); 77 78 /* Definitions needed by ISR or NAPI functions */ 79 static void bdx_rx_alloc_skbs(struct bdx_priv *priv, struct rxf_fifo *f); 80 static void bdx_tx_cleanup(struct bdx_priv *priv); 81 static int bdx_rx_receive(struct bdx_priv *priv, struct rxd_fifo *f, int budget); 82 83 /* Definitions needed by FW loading */ 84 static void bdx_tx_push_desc_safe(struct bdx_priv *priv, void *data, int size); 85 86 /* Definitions needed by hw_start */ 87 static int bdx_tx_init(struct bdx_priv *priv); 88 static int bdx_rx_init(struct bdx_priv *priv); 89 90 /* Definitions needed by bdx_close */ 91 static void bdx_rx_free(struct bdx_priv *priv); 92 static void bdx_tx_free(struct bdx_priv *priv); 93 94 /* Definitions needed by bdx_probe */ 95 static void bdx_set_ethtool_ops(struct net_device *netdev); 96 97 /************************************************************************* 98 * Print Info * 99 *************************************************************************/ 100 101 static void print_hw_id(struct pci_dev *pdev) 102 { 103 struct pci_nic *nic = pci_get_drvdata(pdev); 104 u16 pci_link_status = 0; 105 u16 pci_ctrl = 0; 106 107 pci_read_config_word(pdev, PCI_LINK_STATUS_REG, &pci_link_status); 108 pci_read_config_word(pdev, PCI_DEV_CTRL_REG, &pci_ctrl); 109 110 pr_info("%s%s\n", BDX_NIC_NAME, 111 nic->port_num == 1 ? "" : ", 2-Port"); 112 pr_info("srom 0x%x fpga %d build %u lane# %d max_pl 0x%x mrrs 0x%x\n", 113 readl(nic->regs + SROM_VER), readl(nic->regs + FPGA_VER) & 0xFFF, 114 readl(nic->regs + FPGA_SEED), 115 GET_LINK_STATUS_LANES(pci_link_status), 116 GET_DEV_CTRL_MAXPL(pci_ctrl), GET_DEV_CTRL_MRRS(pci_ctrl)); 117 } 118 119 static void print_fw_id(struct pci_nic *nic) 120 { 121 pr_info("fw 0x%x\n", readl(nic->regs + FW_VER)); 122 } 123 124 static void print_eth_id(struct net_device *ndev) 125 { 126 netdev_info(ndev, "%s, Port %c\n", 127 BDX_NIC_NAME, (ndev->if_port == 0) ? 'A' : 'B'); 128 129 } 130 131 /************************************************************************* 132 * Code * 133 *************************************************************************/ 134 135 #define bdx_enable_interrupts(priv) \ 136 do { WRITE_REG(priv, regIMR, IR_RUN); } while (0) 137 #define bdx_disable_interrupts(priv) \ 138 do { WRITE_REG(priv, regIMR, 0); } while (0) 139 140 /** 141 * bdx_fifo_init - create TX/RX descriptor fifo for host-NIC communication. 142 * @priv: NIC private structure 143 * @f: fifo to initialize 144 * @fsz_type: fifo size type: 0-4KB, 1-8KB, 2-16KB, 3-32KB 145 * @reg_XXX: offsets of registers relative to base address 146 * 147 * 1K extra space is allocated at the end of the fifo to simplify 148 * processing of descriptors that wraps around fifo's end 149 * 150 * Returns 0 on success, negative value on failure 151 * 152 */ 153 static int 154 bdx_fifo_init(struct bdx_priv *priv, struct fifo *f, int fsz_type, 155 u16 reg_CFG0, u16 reg_CFG1, u16 reg_RPTR, u16 reg_WPTR) 156 { 157 u16 memsz = FIFO_SIZE * (1 << fsz_type); 158 159 memset(f, 0, sizeof(struct fifo)); 160 /* pci_alloc_consistent gives us 4k-aligned memory */ 161 f->va = pci_alloc_consistent(priv->pdev, 162 memsz + FIFO_EXTRA_SPACE, &f->da); 163 if (!f->va) { 164 pr_err("pci_alloc_consistent failed\n"); 165 RET(-ENOMEM); 166 } 167 f->reg_CFG0 = reg_CFG0; 168 f->reg_CFG1 = reg_CFG1; 169 f->reg_RPTR = reg_RPTR; 170 f->reg_WPTR = reg_WPTR; 171 f->rptr = 0; 172 f->wptr = 0; 173 f->memsz = memsz; 174 f->size_mask = memsz - 1; 175 WRITE_REG(priv, reg_CFG0, (u32) ((f->da & TX_RX_CFG0_BASE) | fsz_type)); 176 WRITE_REG(priv, reg_CFG1, H32_64(f->da)); 177 178 RET(0); 179 } 180 181 /** 182 * bdx_fifo_free - free all resources used by fifo 183 * @priv: NIC private structure 184 * @f: fifo to release 185 */ 186 static void bdx_fifo_free(struct bdx_priv *priv, struct fifo *f) 187 { 188 ENTER; 189 if (f->va) { 190 pci_free_consistent(priv->pdev, 191 f->memsz + FIFO_EXTRA_SPACE, f->va, f->da); 192 f->va = NULL; 193 } 194 RET(); 195 } 196 197 /** 198 * bdx_link_changed - notifies OS about hw link state. 199 * @priv: hw adapter structure 200 */ 201 static void bdx_link_changed(struct bdx_priv *priv) 202 { 203 u32 link = READ_REG(priv, regMAC_LNK_STAT) & MAC_LINK_STAT; 204 205 if (!link) { 206 if (netif_carrier_ok(priv->ndev)) { 207 netif_stop_queue(priv->ndev); 208 netif_carrier_off(priv->ndev); 209 netdev_err(priv->ndev, "Link Down\n"); 210 } 211 } else { 212 if (!netif_carrier_ok(priv->ndev)) { 213 netif_wake_queue(priv->ndev); 214 netif_carrier_on(priv->ndev); 215 netdev_err(priv->ndev, "Link Up\n"); 216 } 217 } 218 } 219 220 static void bdx_isr_extra(struct bdx_priv *priv, u32 isr) 221 { 222 if (isr & IR_RX_FREE_0) { 223 bdx_rx_alloc_skbs(priv, &priv->rxf_fifo0); 224 DBG("RX_FREE_0\n"); 225 } 226 227 if (isr & IR_LNKCHG0) 228 bdx_link_changed(priv); 229 230 if (isr & IR_PCIE_LINK) 231 netdev_err(priv->ndev, "PCI-E Link Fault\n"); 232 233 if (isr & IR_PCIE_TOUT) 234 netdev_err(priv->ndev, "PCI-E Time Out\n"); 235 236 } 237 238 /** 239 * bdx_isr_napi - Interrupt Service Routine for Bordeaux NIC 240 * @irq: interrupt number 241 * @dev: network device 242 * 243 * Return IRQ_NONE if it was not our interrupt, IRQ_HANDLED - otherwise 244 * 245 * It reads ISR register to know interrupt reasons, and proceed them one by one. 246 * Reasons of interest are: 247 * RX_DESC - new packet has arrived and RXD fifo holds its descriptor 248 * RX_FREE - number of free Rx buffers in RXF fifo gets low 249 * TX_FREE - packet was transmited and RXF fifo holds its descriptor 250 */ 251 252 static irqreturn_t bdx_isr_napi(int irq, void *dev) 253 { 254 struct net_device *ndev = dev; 255 struct bdx_priv *priv = netdev_priv(ndev); 256 u32 isr; 257 258 ENTER; 259 isr = (READ_REG(priv, regISR) & IR_RUN); 260 if (unlikely(!isr)) { 261 bdx_enable_interrupts(priv); 262 return IRQ_NONE; /* Not our interrupt */ 263 } 264 265 if (isr & IR_EXTRA) 266 bdx_isr_extra(priv, isr); 267 268 if (isr & (IR_RX_DESC_0 | IR_TX_FREE_0)) { 269 if (likely(napi_schedule_prep(&priv->napi))) { 270 __napi_schedule(&priv->napi); 271 RET(IRQ_HANDLED); 272 } else { 273 /* NOTE: we get here if intr has slipped into window 274 * between these lines in bdx_poll: 275 * bdx_enable_interrupts(priv); 276 * return 0; 277 * currently intrs are disabled (since we read ISR), 278 * and we have failed to register next poll. 279 * so we read the regs to trigger chip 280 * and allow further interupts. */ 281 READ_REG(priv, regTXF_WPTR_0); 282 READ_REG(priv, regRXD_WPTR_0); 283 } 284 } 285 286 bdx_enable_interrupts(priv); 287 RET(IRQ_HANDLED); 288 } 289 290 static int bdx_poll(struct napi_struct *napi, int budget) 291 { 292 struct bdx_priv *priv = container_of(napi, struct bdx_priv, napi); 293 int work_done; 294 295 ENTER; 296 bdx_tx_cleanup(priv); 297 work_done = bdx_rx_receive(priv, &priv->rxd_fifo0, budget); 298 if ((work_done < budget) || 299 (priv->napi_stop++ >= 30)) { 300 DBG("rx poll is done. backing to isr-driven\n"); 301 302 /* from time to time we exit to let NAPI layer release 303 * device lock and allow waiting tasks (eg rmmod) to advance) */ 304 priv->napi_stop = 0; 305 306 napi_complete_done(napi, work_done); 307 bdx_enable_interrupts(priv); 308 } 309 return work_done; 310 } 311 312 /** 313 * bdx_fw_load - loads firmware to NIC 314 * @priv: NIC private structure 315 * 316 * Firmware is loaded via TXD fifo, so it must be initialized first. 317 * Firware must be loaded once per NIC not per PCI device provided by NIC (NIC 318 * can have few of them). So all drivers use semaphore register to choose one 319 * that will actually load FW to NIC. 320 */ 321 322 static int bdx_fw_load(struct bdx_priv *priv) 323 { 324 const struct firmware *fw = NULL; 325 int master, i; 326 int rc; 327 328 ENTER; 329 master = READ_REG(priv, regINIT_SEMAPHORE); 330 if (!READ_REG(priv, regINIT_STATUS) && master) { 331 rc = request_firmware(&fw, "tehuti/bdx.bin", &priv->pdev->dev); 332 if (rc) 333 goto out; 334 bdx_tx_push_desc_safe(priv, (char *)fw->data, fw->size); 335 mdelay(100); 336 } 337 for (i = 0; i < 200; i++) { 338 if (READ_REG(priv, regINIT_STATUS)) { 339 rc = 0; 340 goto out; 341 } 342 mdelay(2); 343 } 344 rc = -EIO; 345 out: 346 if (master) 347 WRITE_REG(priv, regINIT_SEMAPHORE, 1); 348 349 release_firmware(fw); 350 351 if (rc) { 352 netdev_err(priv->ndev, "firmware loading failed\n"); 353 if (rc == -EIO) 354 DBG("VPC = 0x%x VIC = 0x%x INIT_STATUS = 0x%x i=%d\n", 355 READ_REG(priv, regVPC), 356 READ_REG(priv, regVIC), 357 READ_REG(priv, regINIT_STATUS), i); 358 RET(rc); 359 } else { 360 DBG("%s: firmware loading success\n", priv->ndev->name); 361 RET(0); 362 } 363 } 364 365 static void bdx_restore_mac(struct net_device *ndev, struct bdx_priv *priv) 366 { 367 u32 val; 368 369 ENTER; 370 DBG("mac0=%x mac1=%x mac2=%x\n", 371 READ_REG(priv, regUNC_MAC0_A), 372 READ_REG(priv, regUNC_MAC1_A), READ_REG(priv, regUNC_MAC2_A)); 373 374 val = (ndev->dev_addr[0] << 8) | (ndev->dev_addr[1]); 375 WRITE_REG(priv, regUNC_MAC2_A, val); 376 val = (ndev->dev_addr[2] << 8) | (ndev->dev_addr[3]); 377 WRITE_REG(priv, regUNC_MAC1_A, val); 378 val = (ndev->dev_addr[4] << 8) | (ndev->dev_addr[5]); 379 WRITE_REG(priv, regUNC_MAC0_A, val); 380 381 DBG("mac0=%x mac1=%x mac2=%x\n", 382 READ_REG(priv, regUNC_MAC0_A), 383 READ_REG(priv, regUNC_MAC1_A), READ_REG(priv, regUNC_MAC2_A)); 384 RET(); 385 } 386 387 /** 388 * bdx_hw_start - inits registers and starts HW's Rx and Tx engines 389 * @priv: NIC private structure 390 */ 391 static int bdx_hw_start(struct bdx_priv *priv) 392 { 393 int rc = -EIO; 394 struct net_device *ndev = priv->ndev; 395 396 ENTER; 397 bdx_link_changed(priv); 398 399 /* 10G overall max length (vlan, eth&ip header, ip payload, crc) */ 400 WRITE_REG(priv, regFRM_LENGTH, 0X3FE0); 401 WRITE_REG(priv, regPAUSE_QUANT, 0x96); 402 WRITE_REG(priv, regRX_FIFO_SECTION, 0x800010); 403 WRITE_REG(priv, regTX_FIFO_SECTION, 0xE00010); 404 WRITE_REG(priv, regRX_FULLNESS, 0); 405 WRITE_REG(priv, regTX_FULLNESS, 0); 406 WRITE_REG(priv, regCTRLST, 407 regCTRLST_BASE | regCTRLST_RX_ENA | regCTRLST_TX_ENA); 408 409 WRITE_REG(priv, regVGLB, 0); 410 WRITE_REG(priv, regMAX_FRAME_A, 411 priv->rxf_fifo0.m.pktsz & MAX_FRAME_AB_VAL); 412 413 DBG("RDINTCM=%08x\n", priv->rdintcm); /*NOTE: test script uses this */ 414 WRITE_REG(priv, regRDINTCM0, priv->rdintcm); 415 WRITE_REG(priv, regRDINTCM2, 0); /*cpu_to_le32(rcm.val)); */ 416 417 DBG("TDINTCM=%08x\n", priv->tdintcm); /*NOTE: test script uses this */ 418 WRITE_REG(priv, regTDINTCM0, priv->tdintcm); /* old val = 0x300064 */ 419 420 /* Enable timer interrupt once in 2 secs. */ 421 /*WRITE_REG(priv, regGTMR0, ((GTMR_SEC * 2) & GTMR_DATA)); */ 422 bdx_restore_mac(priv->ndev, priv); 423 424 WRITE_REG(priv, regGMAC_RXF_A, GMAC_RX_FILTER_OSEN | 425 GMAC_RX_FILTER_AM | GMAC_RX_FILTER_AB); 426 427 #define BDX_IRQ_TYPE ((priv->nic->irq_type == IRQ_MSI) ? 0 : IRQF_SHARED) 428 429 rc = request_irq(priv->pdev->irq, bdx_isr_napi, BDX_IRQ_TYPE, 430 ndev->name, ndev); 431 if (rc) 432 goto err_irq; 433 bdx_enable_interrupts(priv); 434 435 RET(0); 436 437 err_irq: 438 RET(rc); 439 } 440 441 static void bdx_hw_stop(struct bdx_priv *priv) 442 { 443 ENTER; 444 bdx_disable_interrupts(priv); 445 free_irq(priv->pdev->irq, priv->ndev); 446 447 netif_carrier_off(priv->ndev); 448 netif_stop_queue(priv->ndev); 449 450 RET(); 451 } 452 453 static int bdx_hw_reset_direct(void __iomem *regs) 454 { 455 u32 val, i; 456 ENTER; 457 458 /* reset sequences: read, write 1, read, write 0 */ 459 val = readl(regs + regCLKPLL); 460 writel((val | CLKPLL_SFTRST) + 0x8, regs + regCLKPLL); 461 udelay(50); 462 val = readl(regs + regCLKPLL); 463 writel(val & ~CLKPLL_SFTRST, regs + regCLKPLL); 464 465 /* check that the PLLs are locked and reset ended */ 466 for (i = 0; i < 70; i++, mdelay(10)) 467 if ((readl(regs + regCLKPLL) & CLKPLL_LKD) == CLKPLL_LKD) { 468 /* do any PCI-E read transaction */ 469 readl(regs + regRXD_CFG0_0); 470 return 0; 471 } 472 pr_err("HW reset failed\n"); 473 return 1; /* failure */ 474 } 475 476 static int bdx_hw_reset(struct bdx_priv *priv) 477 { 478 u32 val, i; 479 ENTER; 480 481 if (priv->port == 0) { 482 /* reset sequences: read, write 1, read, write 0 */ 483 val = READ_REG(priv, regCLKPLL); 484 WRITE_REG(priv, regCLKPLL, (val | CLKPLL_SFTRST) + 0x8); 485 udelay(50); 486 val = READ_REG(priv, regCLKPLL); 487 WRITE_REG(priv, regCLKPLL, val & ~CLKPLL_SFTRST); 488 } 489 /* check that the PLLs are locked and reset ended */ 490 for (i = 0; i < 70; i++, mdelay(10)) 491 if ((READ_REG(priv, regCLKPLL) & CLKPLL_LKD) == CLKPLL_LKD) { 492 /* do any PCI-E read transaction */ 493 READ_REG(priv, regRXD_CFG0_0); 494 return 0; 495 } 496 pr_err("HW reset failed\n"); 497 return 1; /* failure */ 498 } 499 500 static int bdx_sw_reset(struct bdx_priv *priv) 501 { 502 int i; 503 504 ENTER; 505 /* 1. load MAC (obsolete) */ 506 /* 2. disable Rx (and Tx) */ 507 WRITE_REG(priv, regGMAC_RXF_A, 0); 508 mdelay(100); 509 /* 3. disable port */ 510 WRITE_REG(priv, regDIS_PORT, 1); 511 /* 4. disable queue */ 512 WRITE_REG(priv, regDIS_QU, 1); 513 /* 5. wait until hw is disabled */ 514 for (i = 0; i < 50; i++) { 515 if (READ_REG(priv, regRST_PORT) & 1) 516 break; 517 mdelay(10); 518 } 519 if (i == 50) 520 netdev_err(priv->ndev, "SW reset timeout. continuing anyway\n"); 521 522 /* 6. disable intrs */ 523 WRITE_REG(priv, regRDINTCM0, 0); 524 WRITE_REG(priv, regTDINTCM0, 0); 525 WRITE_REG(priv, regIMR, 0); 526 READ_REG(priv, regISR); 527 528 /* 7. reset queue */ 529 WRITE_REG(priv, regRST_QU, 1); 530 /* 8. reset port */ 531 WRITE_REG(priv, regRST_PORT, 1); 532 /* 9. zero all read and write pointers */ 533 for (i = regTXD_WPTR_0; i <= regTXF_RPTR_3; i += 0x10) 534 DBG("%x = %x\n", i, READ_REG(priv, i) & TXF_WPTR_WR_PTR); 535 for (i = regTXD_WPTR_0; i <= regTXF_RPTR_3; i += 0x10) 536 WRITE_REG(priv, i, 0); 537 /* 10. unseet port disable */ 538 WRITE_REG(priv, regDIS_PORT, 0); 539 /* 11. unset queue disable */ 540 WRITE_REG(priv, regDIS_QU, 0); 541 /* 12. unset queue reset */ 542 WRITE_REG(priv, regRST_QU, 0); 543 /* 13. unset port reset */ 544 WRITE_REG(priv, regRST_PORT, 0); 545 /* 14. enable Rx */ 546 /* skiped. will be done later */ 547 /* 15. save MAC (obsolete) */ 548 for (i = regTXD_WPTR_0; i <= regTXF_RPTR_3; i += 0x10) 549 DBG("%x = %x\n", i, READ_REG(priv, i) & TXF_WPTR_WR_PTR); 550 551 RET(0); 552 } 553 554 /* bdx_reset - performs right type of reset depending on hw type */ 555 static int bdx_reset(struct bdx_priv *priv) 556 { 557 ENTER; 558 RET((priv->pdev->device == 0x3009) 559 ? bdx_hw_reset(priv) 560 : bdx_sw_reset(priv)); 561 } 562 563 /** 564 * bdx_close - Disables a network interface 565 * @netdev: network interface device structure 566 * 567 * Returns 0, this is not allowed to fail 568 * 569 * The close entry point is called when an interface is de-activated 570 * by the OS. The hardware is still under the drivers control, but 571 * needs to be disabled. A global MAC reset is issued to stop the 572 * hardware, and all transmit and receive resources are freed. 573 **/ 574 static int bdx_close(struct net_device *ndev) 575 { 576 struct bdx_priv *priv = NULL; 577 578 ENTER; 579 priv = netdev_priv(ndev); 580 581 napi_disable(&priv->napi); 582 583 bdx_reset(priv); 584 bdx_hw_stop(priv); 585 bdx_rx_free(priv); 586 bdx_tx_free(priv); 587 RET(0); 588 } 589 590 /** 591 * bdx_open - Called when a network interface is made active 592 * @netdev: network interface device structure 593 * 594 * Returns 0 on success, negative value on failure 595 * 596 * The open entry point is called when a network interface is made 597 * active by the system (IFF_UP). At this point all resources needed 598 * for transmit and receive operations are allocated, the interrupt 599 * handler is registered with the OS, the watchdog timer is started, 600 * and the stack is notified that the interface is ready. 601 **/ 602 static int bdx_open(struct net_device *ndev) 603 { 604 struct bdx_priv *priv; 605 int rc; 606 607 ENTER; 608 priv = netdev_priv(ndev); 609 bdx_reset(priv); 610 if (netif_running(ndev)) 611 netif_stop_queue(priv->ndev); 612 613 if ((rc = bdx_tx_init(priv)) || 614 (rc = bdx_rx_init(priv)) || 615 (rc = bdx_fw_load(priv))) 616 goto err; 617 618 bdx_rx_alloc_skbs(priv, &priv->rxf_fifo0); 619 620 rc = bdx_hw_start(priv); 621 if (rc) 622 goto err; 623 624 napi_enable(&priv->napi); 625 626 print_fw_id(priv->nic); 627 628 RET(0); 629 630 err: 631 bdx_close(ndev); 632 RET(rc); 633 } 634 635 static int bdx_range_check(struct bdx_priv *priv, u32 offset) 636 { 637 return (offset > (u32) (BDX_REGS_SIZE / priv->nic->port_num)) ? 638 -EINVAL : 0; 639 } 640 641 static int bdx_ioctl_priv(struct net_device *ndev, struct ifreq *ifr, int cmd) 642 { 643 struct bdx_priv *priv = netdev_priv(ndev); 644 u32 data[3]; 645 int error; 646 647 ENTER; 648 649 DBG("jiffies=%ld cmd=%d\n", jiffies, cmd); 650 if (cmd != SIOCDEVPRIVATE) { 651 error = copy_from_user(data, ifr->ifr_data, sizeof(data)); 652 if (error) { 653 pr_err("can't copy from user\n"); 654 RET(-EFAULT); 655 } 656 DBG("%d 0x%x 0x%x\n", data[0], data[1], data[2]); 657 } else { 658 return -EOPNOTSUPP; 659 } 660 661 if (!capable(CAP_SYS_RAWIO)) 662 return -EPERM; 663 664 switch (data[0]) { 665 666 case BDX_OP_READ: 667 error = bdx_range_check(priv, data[1]); 668 if (error < 0) 669 return error; 670 data[2] = READ_REG(priv, data[1]); 671 DBG("read_reg(0x%x)=0x%x (dec %d)\n", data[1], data[2], 672 data[2]); 673 error = copy_to_user(ifr->ifr_data, data, sizeof(data)); 674 if (error) 675 RET(-EFAULT); 676 break; 677 678 case BDX_OP_WRITE: 679 error = bdx_range_check(priv, data[1]); 680 if (error < 0) 681 return error; 682 WRITE_REG(priv, data[1], data[2]); 683 DBG("write_reg(0x%x, 0x%x)\n", data[1], data[2]); 684 break; 685 686 default: 687 RET(-EOPNOTSUPP); 688 } 689 return 0; 690 } 691 692 static int bdx_ioctl(struct net_device *ndev, struct ifreq *ifr, int cmd) 693 { 694 ENTER; 695 if (cmd >= SIOCDEVPRIVATE && cmd <= (SIOCDEVPRIVATE + 15)) 696 RET(bdx_ioctl_priv(ndev, ifr, cmd)); 697 else 698 RET(-EOPNOTSUPP); 699 } 700 701 /** 702 * __bdx_vlan_rx_vid - private helper for adding/killing VLAN vid 703 * @ndev: network device 704 * @vid: VLAN vid 705 * @op: add or kill operation 706 * 707 * Passes VLAN filter table to hardware 708 */ 709 static void __bdx_vlan_rx_vid(struct net_device *ndev, uint16_t vid, int enable) 710 { 711 struct bdx_priv *priv = netdev_priv(ndev); 712 u32 reg, bit, val; 713 714 ENTER; 715 DBG2("vid=%d value=%d\n", (int)vid, enable); 716 if (unlikely(vid >= 4096)) { 717 pr_err("invalid VID: %u (> 4096)\n", vid); 718 RET(); 719 } 720 reg = regVLAN_0 + (vid / 32) * 4; 721 bit = 1 << vid % 32; 722 val = READ_REG(priv, reg); 723 DBG2("reg=%x, val=%x, bit=%d\n", reg, val, bit); 724 if (enable) 725 val |= bit; 726 else 727 val &= ~bit; 728 DBG2("new val %x\n", val); 729 WRITE_REG(priv, reg, val); 730 RET(); 731 } 732 733 /** 734 * bdx_vlan_rx_add_vid - kernel hook for adding VLAN vid to hw filtering table 735 * @ndev: network device 736 * @vid: VLAN vid to add 737 */ 738 static int bdx_vlan_rx_add_vid(struct net_device *ndev, __be16 proto, u16 vid) 739 { 740 __bdx_vlan_rx_vid(ndev, vid, 1); 741 return 0; 742 } 743 744 /** 745 * bdx_vlan_rx_kill_vid - kernel hook for killing VLAN vid in hw filtering table 746 * @ndev: network device 747 * @vid: VLAN vid to kill 748 */ 749 static int bdx_vlan_rx_kill_vid(struct net_device *ndev, __be16 proto, u16 vid) 750 { 751 __bdx_vlan_rx_vid(ndev, vid, 0); 752 return 0; 753 } 754 755 /** 756 * bdx_change_mtu - Change the Maximum Transfer Unit 757 * @netdev: network interface device structure 758 * @new_mtu: new value for maximum frame size 759 * 760 * Returns 0 on success, negative on failure 761 */ 762 static int bdx_change_mtu(struct net_device *ndev, int new_mtu) 763 { 764 ENTER; 765 766 ndev->mtu = new_mtu; 767 if (netif_running(ndev)) { 768 bdx_close(ndev); 769 bdx_open(ndev); 770 } 771 RET(0); 772 } 773 774 static void bdx_setmulti(struct net_device *ndev) 775 { 776 struct bdx_priv *priv = netdev_priv(ndev); 777 778 u32 rxf_val = 779 GMAC_RX_FILTER_AM | GMAC_RX_FILTER_AB | GMAC_RX_FILTER_OSEN; 780 int i; 781 782 ENTER; 783 /* IMF - imperfect (hash) rx multicat filter */ 784 /* PMF - perfect rx multicat filter */ 785 786 /* FIXME: RXE(OFF) */ 787 if (ndev->flags & IFF_PROMISC) { 788 rxf_val |= GMAC_RX_FILTER_PRM; 789 } else if (ndev->flags & IFF_ALLMULTI) { 790 /* set IMF to accept all multicast frmaes */ 791 for (i = 0; i < MAC_MCST_HASH_NUM; i++) 792 WRITE_REG(priv, regRX_MCST_HASH0 + i * 4, ~0); 793 } else if (!netdev_mc_empty(ndev)) { 794 u8 hash; 795 struct netdev_hw_addr *ha; 796 u32 reg, val; 797 798 /* set IMF to deny all multicast frames */ 799 for (i = 0; i < MAC_MCST_HASH_NUM; i++) 800 WRITE_REG(priv, regRX_MCST_HASH0 + i * 4, 0); 801 /* set PMF to deny all multicast frames */ 802 for (i = 0; i < MAC_MCST_NUM; i++) { 803 WRITE_REG(priv, regRX_MAC_MCST0 + i * 8, 0); 804 WRITE_REG(priv, regRX_MAC_MCST1 + i * 8, 0); 805 } 806 807 /* use PMF to accept first MAC_MCST_NUM (15) addresses */ 808 /* TBD: sort addresses and write them in ascending order 809 * into RX_MAC_MCST regs. we skip this phase now and accept ALL 810 * multicast frames throu IMF */ 811 /* accept the rest of addresses throu IMF */ 812 netdev_for_each_mc_addr(ha, ndev) { 813 hash = 0; 814 for (i = 0; i < ETH_ALEN; i++) 815 hash ^= ha->addr[i]; 816 reg = regRX_MCST_HASH0 + ((hash >> 5) << 2); 817 val = READ_REG(priv, reg); 818 val |= (1 << (hash % 32)); 819 WRITE_REG(priv, reg, val); 820 } 821 822 } else { 823 DBG("only own mac %d\n", netdev_mc_count(ndev)); 824 rxf_val |= GMAC_RX_FILTER_AB; 825 } 826 WRITE_REG(priv, regGMAC_RXF_A, rxf_val); 827 /* enable RX */ 828 /* FIXME: RXE(ON) */ 829 RET(); 830 } 831 832 static int bdx_set_mac(struct net_device *ndev, void *p) 833 { 834 struct bdx_priv *priv = netdev_priv(ndev); 835 struct sockaddr *addr = p; 836 837 ENTER; 838 /* 839 if (netif_running(dev)) 840 return -EBUSY 841 */ 842 memcpy(ndev->dev_addr, addr->sa_data, ndev->addr_len); 843 bdx_restore_mac(ndev, priv); 844 RET(0); 845 } 846 847 static int bdx_read_mac(struct bdx_priv *priv) 848 { 849 u16 macAddress[3], i; 850 ENTER; 851 852 macAddress[2] = READ_REG(priv, regUNC_MAC0_A); 853 macAddress[2] = READ_REG(priv, regUNC_MAC0_A); 854 macAddress[1] = READ_REG(priv, regUNC_MAC1_A); 855 macAddress[1] = READ_REG(priv, regUNC_MAC1_A); 856 macAddress[0] = READ_REG(priv, regUNC_MAC2_A); 857 macAddress[0] = READ_REG(priv, regUNC_MAC2_A); 858 for (i = 0; i < 3; i++) { 859 priv->ndev->dev_addr[i * 2 + 1] = macAddress[i]; 860 priv->ndev->dev_addr[i * 2] = macAddress[i] >> 8; 861 } 862 RET(0); 863 } 864 865 static u64 bdx_read_l2stat(struct bdx_priv *priv, int reg) 866 { 867 u64 val; 868 869 val = READ_REG(priv, reg); 870 val |= ((u64) READ_REG(priv, reg + 8)) << 32; 871 return val; 872 } 873 874 /*Do the statistics-update work*/ 875 static void bdx_update_stats(struct bdx_priv *priv) 876 { 877 struct bdx_stats *stats = &priv->hw_stats; 878 u64 *stats_vector = (u64 *) stats; 879 int i; 880 int addr; 881 882 /*Fill HW structure */ 883 addr = 0x7200; 884 /*First 12 statistics - 0x7200 - 0x72B0 */ 885 for (i = 0; i < 12; i++) { 886 stats_vector[i] = bdx_read_l2stat(priv, addr); 887 addr += 0x10; 888 } 889 BDX_ASSERT(addr != 0x72C0); 890 /* 0x72C0-0x72E0 RSRV */ 891 addr = 0x72F0; 892 for (; i < 16; i++) { 893 stats_vector[i] = bdx_read_l2stat(priv, addr); 894 addr += 0x10; 895 } 896 BDX_ASSERT(addr != 0x7330); 897 /* 0x7330-0x7360 RSRV */ 898 addr = 0x7370; 899 for (; i < 19; i++) { 900 stats_vector[i] = bdx_read_l2stat(priv, addr); 901 addr += 0x10; 902 } 903 BDX_ASSERT(addr != 0x73A0); 904 /* 0x73A0-0x73B0 RSRV */ 905 addr = 0x73C0; 906 for (; i < 23; i++) { 907 stats_vector[i] = bdx_read_l2stat(priv, addr); 908 addr += 0x10; 909 } 910 BDX_ASSERT(addr != 0x7400); 911 BDX_ASSERT((sizeof(struct bdx_stats) / sizeof(u64)) != i); 912 } 913 914 static void print_rxdd(struct rxd_desc *rxdd, u32 rxd_val1, u16 len, 915 u16 rxd_vlan); 916 static void print_rxfd(struct rxf_desc *rxfd); 917 918 /************************************************************************* 919 * Rx DB * 920 *************************************************************************/ 921 922 static void bdx_rxdb_destroy(struct rxdb *db) 923 { 924 vfree(db); 925 } 926 927 static struct rxdb *bdx_rxdb_create(int nelem) 928 { 929 struct rxdb *db; 930 int i; 931 932 db = vmalloc(sizeof(struct rxdb) 933 + (nelem * sizeof(int)) 934 + (nelem * sizeof(struct rx_map))); 935 if (likely(db != NULL)) { 936 db->stack = (int *)(db + 1); 937 db->elems = (void *)(db->stack + nelem); 938 db->nelem = nelem; 939 db->top = nelem; 940 for (i = 0; i < nelem; i++) 941 db->stack[i] = nelem - i - 1; /* to make first allocs 942 close to db struct*/ 943 } 944 945 return db; 946 } 947 948 static inline int bdx_rxdb_alloc_elem(struct rxdb *db) 949 { 950 BDX_ASSERT(db->top <= 0); 951 return db->stack[--(db->top)]; 952 } 953 954 static inline void *bdx_rxdb_addr_elem(struct rxdb *db, int n) 955 { 956 BDX_ASSERT((n < 0) || (n >= db->nelem)); 957 return db->elems + n; 958 } 959 960 static inline int bdx_rxdb_available(struct rxdb *db) 961 { 962 return db->top; 963 } 964 965 static inline void bdx_rxdb_free_elem(struct rxdb *db, int n) 966 { 967 BDX_ASSERT((n >= db->nelem) || (n < 0)); 968 db->stack[(db->top)++] = n; 969 } 970 971 /************************************************************************* 972 * Rx Init * 973 *************************************************************************/ 974 975 /** 976 * bdx_rx_init - initialize RX all related HW and SW resources 977 * @priv: NIC private structure 978 * 979 * Returns 0 on success, negative value on failure 980 * 981 * It creates rxf and rxd fifos, update relevant HW registers, preallocate 982 * skb for rx. It assumes that Rx is desabled in HW 983 * funcs are grouped for better cache usage 984 * 985 * RxD fifo is smaller than RxF fifo by design. Upon high load, RxD will be 986 * filled and packets will be dropped by nic without getting into host or 987 * cousing interrupt. Anyway, in that condition, host has no chance to process 988 * all packets, but dropping in nic is cheaper, since it takes 0 cpu cycles 989 */ 990 991 /* TBD: ensure proper packet size */ 992 993 static int bdx_rx_init(struct bdx_priv *priv) 994 { 995 ENTER; 996 997 if (bdx_fifo_init(priv, &priv->rxd_fifo0.m, priv->rxd_size, 998 regRXD_CFG0_0, regRXD_CFG1_0, 999 regRXD_RPTR_0, regRXD_WPTR_0)) 1000 goto err_mem; 1001 if (bdx_fifo_init(priv, &priv->rxf_fifo0.m, priv->rxf_size, 1002 regRXF_CFG0_0, regRXF_CFG1_0, 1003 regRXF_RPTR_0, regRXF_WPTR_0)) 1004 goto err_mem; 1005 priv->rxdb = bdx_rxdb_create(priv->rxf_fifo0.m.memsz / 1006 sizeof(struct rxf_desc)); 1007 if (!priv->rxdb) 1008 goto err_mem; 1009 1010 priv->rxf_fifo0.m.pktsz = priv->ndev->mtu + VLAN_ETH_HLEN; 1011 return 0; 1012 1013 err_mem: 1014 netdev_err(priv->ndev, "Rx init failed\n"); 1015 return -ENOMEM; 1016 } 1017 1018 /** 1019 * bdx_rx_free_skbs - frees and unmaps all skbs allocated for the fifo 1020 * @priv: NIC private structure 1021 * @f: RXF fifo 1022 */ 1023 static void bdx_rx_free_skbs(struct bdx_priv *priv, struct rxf_fifo *f) 1024 { 1025 struct rx_map *dm; 1026 struct rxdb *db = priv->rxdb; 1027 u16 i; 1028 1029 ENTER; 1030 DBG("total=%d free=%d busy=%d\n", db->nelem, bdx_rxdb_available(db), 1031 db->nelem - bdx_rxdb_available(db)); 1032 while (bdx_rxdb_available(db) > 0) { 1033 i = bdx_rxdb_alloc_elem(db); 1034 dm = bdx_rxdb_addr_elem(db, i); 1035 dm->dma = 0; 1036 } 1037 for (i = 0; i < db->nelem; i++) { 1038 dm = bdx_rxdb_addr_elem(db, i); 1039 if (dm->dma) { 1040 pci_unmap_single(priv->pdev, 1041 dm->dma, f->m.pktsz, 1042 PCI_DMA_FROMDEVICE); 1043 dev_kfree_skb(dm->skb); 1044 } 1045 } 1046 } 1047 1048 /** 1049 * bdx_rx_free - release all Rx resources 1050 * @priv: NIC private structure 1051 * 1052 * It assumes that Rx is desabled in HW 1053 */ 1054 static void bdx_rx_free(struct bdx_priv *priv) 1055 { 1056 ENTER; 1057 if (priv->rxdb) { 1058 bdx_rx_free_skbs(priv, &priv->rxf_fifo0); 1059 bdx_rxdb_destroy(priv->rxdb); 1060 priv->rxdb = NULL; 1061 } 1062 bdx_fifo_free(priv, &priv->rxf_fifo0.m); 1063 bdx_fifo_free(priv, &priv->rxd_fifo0.m); 1064 1065 RET(); 1066 } 1067 1068 /************************************************************************* 1069 * Rx Engine * 1070 *************************************************************************/ 1071 1072 /** 1073 * bdx_rx_alloc_skbs - fill rxf fifo with new skbs 1074 * @priv: nic's private structure 1075 * @f: RXF fifo that needs skbs 1076 * 1077 * It allocates skbs, build rxf descs and push it (rxf descr) into rxf fifo. 1078 * skb's virtual and physical addresses are stored in skb db. 1079 * To calculate free space, func uses cached values of RPTR and WPTR 1080 * When needed, it also updates RPTR and WPTR. 1081 */ 1082 1083 /* TBD: do not update WPTR if no desc were written */ 1084 1085 static void bdx_rx_alloc_skbs(struct bdx_priv *priv, struct rxf_fifo *f) 1086 { 1087 struct sk_buff *skb; 1088 struct rxf_desc *rxfd; 1089 struct rx_map *dm; 1090 int dno, delta, idx; 1091 struct rxdb *db = priv->rxdb; 1092 1093 ENTER; 1094 dno = bdx_rxdb_available(db) - 1; 1095 while (dno > 0) { 1096 skb = netdev_alloc_skb(priv->ndev, f->m.pktsz + NET_IP_ALIGN); 1097 if (!skb) 1098 break; 1099 1100 skb_reserve(skb, NET_IP_ALIGN); 1101 1102 idx = bdx_rxdb_alloc_elem(db); 1103 dm = bdx_rxdb_addr_elem(db, idx); 1104 dm->dma = pci_map_single(priv->pdev, 1105 skb->data, f->m.pktsz, 1106 PCI_DMA_FROMDEVICE); 1107 dm->skb = skb; 1108 rxfd = (struct rxf_desc *)(f->m.va + f->m.wptr); 1109 rxfd->info = CPU_CHIP_SWAP32(0x10003); /* INFO=1 BC=3 */ 1110 rxfd->va_lo = idx; 1111 rxfd->pa_lo = CPU_CHIP_SWAP32(L32_64(dm->dma)); 1112 rxfd->pa_hi = CPU_CHIP_SWAP32(H32_64(dm->dma)); 1113 rxfd->len = CPU_CHIP_SWAP32(f->m.pktsz); 1114 print_rxfd(rxfd); 1115 1116 f->m.wptr += sizeof(struct rxf_desc); 1117 delta = f->m.wptr - f->m.memsz; 1118 if (unlikely(delta >= 0)) { 1119 f->m.wptr = delta; 1120 if (delta > 0) { 1121 memcpy(f->m.va, f->m.va + f->m.memsz, delta); 1122 DBG("wrapped descriptor\n"); 1123 } 1124 } 1125 dno--; 1126 } 1127 /*TBD: to do - delayed rxf wptr like in txd */ 1128 WRITE_REG(priv, f->m.reg_WPTR, f->m.wptr & TXF_WPTR_WR_PTR); 1129 RET(); 1130 } 1131 1132 static inline void 1133 NETIF_RX_MUX(struct bdx_priv *priv, u32 rxd_val1, u16 rxd_vlan, 1134 struct sk_buff *skb) 1135 { 1136 ENTER; 1137 DBG("rxdd->flags.bits.vtag=%d\n", GET_RXD_VTAG(rxd_val1)); 1138 if (GET_RXD_VTAG(rxd_val1)) { 1139 DBG("%s: vlan rcv vlan '%x' vtag '%x'\n", 1140 priv->ndev->name, 1141 GET_RXD_VLAN_ID(rxd_vlan), 1142 GET_RXD_VTAG(rxd_val1)); 1143 __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), GET_RXD_VLAN_TCI(rxd_vlan)); 1144 } 1145 netif_receive_skb(skb); 1146 } 1147 1148 static void bdx_recycle_skb(struct bdx_priv *priv, struct rxd_desc *rxdd) 1149 { 1150 struct rxf_desc *rxfd; 1151 struct rx_map *dm; 1152 struct rxf_fifo *f; 1153 struct rxdb *db; 1154 int delta; 1155 1156 ENTER; 1157 DBG("priv=%p rxdd=%p\n", priv, rxdd); 1158 f = &priv->rxf_fifo0; 1159 db = priv->rxdb; 1160 DBG("db=%p f=%p\n", db, f); 1161 dm = bdx_rxdb_addr_elem(db, rxdd->va_lo); 1162 DBG("dm=%p\n", dm); 1163 rxfd = (struct rxf_desc *)(f->m.va + f->m.wptr); 1164 rxfd->info = CPU_CHIP_SWAP32(0x10003); /* INFO=1 BC=3 */ 1165 rxfd->va_lo = rxdd->va_lo; 1166 rxfd->pa_lo = CPU_CHIP_SWAP32(L32_64(dm->dma)); 1167 rxfd->pa_hi = CPU_CHIP_SWAP32(H32_64(dm->dma)); 1168 rxfd->len = CPU_CHIP_SWAP32(f->m.pktsz); 1169 print_rxfd(rxfd); 1170 1171 f->m.wptr += sizeof(struct rxf_desc); 1172 delta = f->m.wptr - f->m.memsz; 1173 if (unlikely(delta >= 0)) { 1174 f->m.wptr = delta; 1175 if (delta > 0) { 1176 memcpy(f->m.va, f->m.va + f->m.memsz, delta); 1177 DBG("wrapped descriptor\n"); 1178 } 1179 } 1180 RET(); 1181 } 1182 1183 /** 1184 * bdx_rx_receive - receives full packets from RXD fifo and pass them to OS 1185 * NOTE: a special treatment is given to non-continuous descriptors 1186 * that start near the end, wraps around and continue at the beginning. a second 1187 * part is copied right after the first, and then descriptor is interpreted as 1188 * normal. fifo has an extra space to allow such operations 1189 * @priv: nic's private structure 1190 * @f: RXF fifo that needs skbs 1191 * @budget: maximum number of packets to receive 1192 */ 1193 1194 /* TBD: replace memcpy func call by explicite inline asm */ 1195 1196 static int bdx_rx_receive(struct bdx_priv *priv, struct rxd_fifo *f, int budget) 1197 { 1198 struct net_device *ndev = priv->ndev; 1199 struct sk_buff *skb, *skb2; 1200 struct rxd_desc *rxdd; 1201 struct rx_map *dm; 1202 struct rxf_fifo *rxf_fifo; 1203 int tmp_len, size; 1204 int done = 0; 1205 int max_done = BDX_MAX_RX_DONE; 1206 struct rxdb *db = NULL; 1207 /* Unmarshalled descriptor - copy of descriptor in host order */ 1208 u32 rxd_val1; 1209 u16 len; 1210 u16 rxd_vlan; 1211 1212 ENTER; 1213 max_done = budget; 1214 1215 f->m.wptr = READ_REG(priv, f->m.reg_WPTR) & TXF_WPTR_WR_PTR; 1216 1217 size = f->m.wptr - f->m.rptr; 1218 if (size < 0) 1219 size = f->m.memsz + size; /* size is negative :-) */ 1220 1221 while (size > 0) { 1222 1223 rxdd = (struct rxd_desc *)(f->m.va + f->m.rptr); 1224 rxd_val1 = CPU_CHIP_SWAP32(rxdd->rxd_val1); 1225 1226 len = CPU_CHIP_SWAP16(rxdd->len); 1227 1228 rxd_vlan = CPU_CHIP_SWAP16(rxdd->rxd_vlan); 1229 1230 print_rxdd(rxdd, rxd_val1, len, rxd_vlan); 1231 1232 tmp_len = GET_RXD_BC(rxd_val1) << 3; 1233 BDX_ASSERT(tmp_len <= 0); 1234 size -= tmp_len; 1235 if (size < 0) /* test for partially arrived descriptor */ 1236 break; 1237 1238 f->m.rptr += tmp_len; 1239 1240 tmp_len = f->m.rptr - f->m.memsz; 1241 if (unlikely(tmp_len >= 0)) { 1242 f->m.rptr = tmp_len; 1243 if (tmp_len > 0) { 1244 DBG("wrapped desc rptr=%d tmp_len=%d\n", 1245 f->m.rptr, tmp_len); 1246 memcpy(f->m.va + f->m.memsz, f->m.va, tmp_len); 1247 } 1248 } 1249 1250 if (unlikely(GET_RXD_ERR(rxd_val1))) { 1251 DBG("rxd_err = 0x%x\n", GET_RXD_ERR(rxd_val1)); 1252 ndev->stats.rx_errors++; 1253 bdx_recycle_skb(priv, rxdd); 1254 continue; 1255 } 1256 1257 rxf_fifo = &priv->rxf_fifo0; 1258 db = priv->rxdb; 1259 dm = bdx_rxdb_addr_elem(db, rxdd->va_lo); 1260 skb = dm->skb; 1261 1262 if (len < BDX_COPYBREAK && 1263 (skb2 = netdev_alloc_skb(priv->ndev, len + NET_IP_ALIGN))) { 1264 skb_reserve(skb2, NET_IP_ALIGN); 1265 /*skb_put(skb2, len); */ 1266 pci_dma_sync_single_for_cpu(priv->pdev, 1267 dm->dma, rxf_fifo->m.pktsz, 1268 PCI_DMA_FROMDEVICE); 1269 memcpy(skb2->data, skb->data, len); 1270 bdx_recycle_skb(priv, rxdd); 1271 skb = skb2; 1272 } else { 1273 pci_unmap_single(priv->pdev, 1274 dm->dma, rxf_fifo->m.pktsz, 1275 PCI_DMA_FROMDEVICE); 1276 bdx_rxdb_free_elem(db, rxdd->va_lo); 1277 } 1278 1279 ndev->stats.rx_bytes += len; 1280 1281 skb_put(skb, len); 1282 skb->protocol = eth_type_trans(skb, ndev); 1283 1284 /* Non-IP packets aren't checksum-offloaded */ 1285 if (GET_RXD_PKT_ID(rxd_val1) == 0) 1286 skb_checksum_none_assert(skb); 1287 else 1288 skb->ip_summed = CHECKSUM_UNNECESSARY; 1289 1290 NETIF_RX_MUX(priv, rxd_val1, rxd_vlan, skb); 1291 1292 if (++done >= max_done) 1293 break; 1294 } 1295 1296 ndev->stats.rx_packets += done; 1297 1298 /* FIXME: do smth to minimize pci accesses */ 1299 WRITE_REG(priv, f->m.reg_RPTR, f->m.rptr & TXF_WPTR_WR_PTR); 1300 1301 bdx_rx_alloc_skbs(priv, &priv->rxf_fifo0); 1302 1303 RET(done); 1304 } 1305 1306 /************************************************************************* 1307 * Debug / Temprorary Code * 1308 *************************************************************************/ 1309 static void print_rxdd(struct rxd_desc *rxdd, u32 rxd_val1, u16 len, 1310 u16 rxd_vlan) 1311 { 1312 DBG("ERROR: rxdd bc %d rxfq %d to %d type %d err %d rxp %d pkt_id %d vtag %d len %d vlan_id %d cfi %d prio %d va_lo %d va_hi %d\n", 1313 GET_RXD_BC(rxd_val1), GET_RXD_RXFQ(rxd_val1), GET_RXD_TO(rxd_val1), 1314 GET_RXD_TYPE(rxd_val1), GET_RXD_ERR(rxd_val1), 1315 GET_RXD_RXP(rxd_val1), GET_RXD_PKT_ID(rxd_val1), 1316 GET_RXD_VTAG(rxd_val1), len, GET_RXD_VLAN_ID(rxd_vlan), 1317 GET_RXD_CFI(rxd_vlan), GET_RXD_PRIO(rxd_vlan), rxdd->va_lo, 1318 rxdd->va_hi); 1319 } 1320 1321 static void print_rxfd(struct rxf_desc *rxfd) 1322 { 1323 DBG("=== RxF desc CHIP ORDER/ENDIANNESS =============\n" 1324 "info 0x%x va_lo %u pa_lo 0x%x pa_hi 0x%x len 0x%x\n", 1325 rxfd->info, rxfd->va_lo, rxfd->pa_lo, rxfd->pa_hi, rxfd->len); 1326 } 1327 1328 /* 1329 * TX HW/SW interaction overview 1330 * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1331 * There are 2 types of TX communication channels between driver and NIC. 1332 * 1) TX Free Fifo - TXF - holds ack descriptors for sent packets 1333 * 2) TX Data Fifo - TXD - holds descriptors of full buffers. 1334 * 1335 * Currently NIC supports TSO, checksuming and gather DMA 1336 * UFO and IP fragmentation is on the way 1337 * 1338 * RX SW Data Structures 1339 * ~~~~~~~~~~~~~~~~~~~~~ 1340 * txdb - used to keep track of all skbs owned by SW and their dma addresses. 1341 * For TX case, ownership lasts from geting packet via hard_xmit and until HW 1342 * acknowledges sent by TXF descriptors. 1343 * Implemented as cyclic buffer. 1344 * fifo - keeps info about fifo's size and location, relevant HW registers, 1345 * usage and skb db. Each RXD and RXF Fifo has its own fifo structure. 1346 * Implemented as simple struct. 1347 * 1348 * TX SW Execution Flow 1349 * ~~~~~~~~~~~~~~~~~~~~ 1350 * OS calls driver's hard_xmit method with packet to sent. 1351 * Driver creates DMA mappings, builds TXD descriptors and kicks HW 1352 * by updating TXD WPTR. 1353 * When packet is sent, HW write us TXF descriptor and SW frees original skb. 1354 * To prevent TXD fifo overflow without reading HW registers every time, 1355 * SW deploys "tx level" technique. 1356 * Upon strart up, tx level is initialized to TXD fifo length. 1357 * For every sent packet, SW gets its TXD descriptor sizei 1358 * (from precalculated array) and substructs it from tx level. 1359 * The size is also stored in txdb. When TXF ack arrives, SW fetch size of 1360 * original TXD descriptor from txdb and adds it to tx level. 1361 * When Tx level drops under some predefined treshhold, the driver 1362 * stops the TX queue. When TX level rises above that level, 1363 * the tx queue is enabled again. 1364 * 1365 * This technique avoids eccessive reading of RPTR and WPTR registers. 1366 * As our benchmarks shows, it adds 1.5 Gbit/sec to NIS's throuput. 1367 */ 1368 1369 /************************************************************************* 1370 * Tx DB * 1371 *************************************************************************/ 1372 static inline int bdx_tx_db_size(struct txdb *db) 1373 { 1374 int taken = db->wptr - db->rptr; 1375 if (taken < 0) 1376 taken = db->size + 1 + taken; /* (size + 1) equals memsz */ 1377 1378 return db->size - taken; 1379 } 1380 1381 /** 1382 * __bdx_tx_db_ptr_next - helper function, increment read/write pointer + wrap 1383 * @db: tx data base 1384 * @pptr: read or write pointer 1385 */ 1386 static inline void __bdx_tx_db_ptr_next(struct txdb *db, struct tx_map **pptr) 1387 { 1388 BDX_ASSERT(db == NULL || pptr == NULL); /* sanity */ 1389 1390 BDX_ASSERT(*pptr != db->rptr && /* expect either read */ 1391 *pptr != db->wptr); /* or write pointer */ 1392 1393 BDX_ASSERT(*pptr < db->start || /* pointer has to be */ 1394 *pptr >= db->end); /* in range */ 1395 1396 ++*pptr; 1397 if (unlikely(*pptr == db->end)) 1398 *pptr = db->start; 1399 } 1400 1401 /** 1402 * bdx_tx_db_inc_rptr - increment read pointer 1403 * @db: tx data base 1404 */ 1405 static inline void bdx_tx_db_inc_rptr(struct txdb *db) 1406 { 1407 BDX_ASSERT(db->rptr == db->wptr); /* can't read from empty db */ 1408 __bdx_tx_db_ptr_next(db, &db->rptr); 1409 } 1410 1411 /** 1412 * bdx_tx_db_inc_wptr - increment write pointer 1413 * @db: tx data base 1414 */ 1415 static inline void bdx_tx_db_inc_wptr(struct txdb *db) 1416 { 1417 __bdx_tx_db_ptr_next(db, &db->wptr); 1418 BDX_ASSERT(db->rptr == db->wptr); /* we can not get empty db as 1419 a result of write */ 1420 } 1421 1422 /** 1423 * bdx_tx_db_init - creates and initializes tx db 1424 * @d: tx data base 1425 * @sz_type: size of tx fifo 1426 * 1427 * Returns 0 on success, error code otherwise 1428 */ 1429 static int bdx_tx_db_init(struct txdb *d, int sz_type) 1430 { 1431 int memsz = FIFO_SIZE * (1 << (sz_type + 1)); 1432 1433 d->start = vmalloc(memsz); 1434 if (!d->start) 1435 return -ENOMEM; 1436 1437 /* 1438 * In order to differentiate between db is empty and db is full 1439 * states at least one element should always be empty in order to 1440 * avoid rptr == wptr which means db is empty 1441 */ 1442 d->size = memsz / sizeof(struct tx_map) - 1; 1443 d->end = d->start + d->size + 1; /* just after last element */ 1444 1445 /* all dbs are created equally empty */ 1446 d->rptr = d->start; 1447 d->wptr = d->start; 1448 1449 return 0; 1450 } 1451 1452 /** 1453 * bdx_tx_db_close - closes tx db and frees all memory 1454 * @d: tx data base 1455 */ 1456 static void bdx_tx_db_close(struct txdb *d) 1457 { 1458 BDX_ASSERT(d == NULL); 1459 1460 vfree(d->start); 1461 d->start = NULL; 1462 } 1463 1464 /************************************************************************* 1465 * Tx Engine * 1466 *************************************************************************/ 1467 1468 /* sizes of tx desc (including padding if needed) as function 1469 * of skb's frag number */ 1470 static struct { 1471 u16 bytes; 1472 u16 qwords; /* qword = 64 bit */ 1473 } txd_sizes[MAX_SKB_FRAGS + 1]; 1474 1475 /** 1476 * bdx_tx_map_skb - creates and stores dma mappings for skb's data blocks 1477 * @priv: NIC private structure 1478 * @skb: socket buffer to map 1479 * @txdd: TX descriptor to use 1480 * 1481 * It makes dma mappings for skb's data blocks and writes them to PBL of 1482 * new tx descriptor. It also stores them in the tx db, so they could be 1483 * unmaped after data was sent. It is reponsibility of a caller to make 1484 * sure that there is enough space in the tx db. Last element holds pointer 1485 * to skb itself and marked with zero length 1486 */ 1487 static inline void 1488 bdx_tx_map_skb(struct bdx_priv *priv, struct sk_buff *skb, 1489 struct txd_desc *txdd) 1490 { 1491 struct txdb *db = &priv->txdb; 1492 struct pbl *pbl = &txdd->pbl[0]; 1493 int nr_frags = skb_shinfo(skb)->nr_frags; 1494 int i; 1495 1496 db->wptr->len = skb_headlen(skb); 1497 db->wptr->addr.dma = pci_map_single(priv->pdev, skb->data, 1498 db->wptr->len, PCI_DMA_TODEVICE); 1499 pbl->len = CPU_CHIP_SWAP32(db->wptr->len); 1500 pbl->pa_lo = CPU_CHIP_SWAP32(L32_64(db->wptr->addr.dma)); 1501 pbl->pa_hi = CPU_CHIP_SWAP32(H32_64(db->wptr->addr.dma)); 1502 DBG("=== pbl len: 0x%x ================\n", pbl->len); 1503 DBG("=== pbl pa_lo: 0x%x ================\n", pbl->pa_lo); 1504 DBG("=== pbl pa_hi: 0x%x ================\n", pbl->pa_hi); 1505 bdx_tx_db_inc_wptr(db); 1506 1507 for (i = 0; i < nr_frags; i++) { 1508 const struct skb_frag_struct *frag; 1509 1510 frag = &skb_shinfo(skb)->frags[i]; 1511 db->wptr->len = skb_frag_size(frag); 1512 db->wptr->addr.dma = skb_frag_dma_map(&priv->pdev->dev, frag, 1513 0, skb_frag_size(frag), 1514 DMA_TO_DEVICE); 1515 1516 pbl++; 1517 pbl->len = CPU_CHIP_SWAP32(db->wptr->len); 1518 pbl->pa_lo = CPU_CHIP_SWAP32(L32_64(db->wptr->addr.dma)); 1519 pbl->pa_hi = CPU_CHIP_SWAP32(H32_64(db->wptr->addr.dma)); 1520 bdx_tx_db_inc_wptr(db); 1521 } 1522 1523 /* add skb clean up info. */ 1524 db->wptr->len = -txd_sizes[nr_frags].bytes; 1525 db->wptr->addr.skb = skb; 1526 bdx_tx_db_inc_wptr(db); 1527 } 1528 1529 /* init_txd_sizes - precalculate sizes of descriptors for skbs up to 16 frags 1530 * number of frags is used as index to fetch correct descriptors size, 1531 * instead of calculating it each time */ 1532 static void __init init_txd_sizes(void) 1533 { 1534 int i, lwords; 1535 1536 /* 7 - is number of lwords in txd with one phys buffer 1537 * 3 - is number of lwords used for every additional phys buffer */ 1538 for (i = 0; i < MAX_SKB_FRAGS + 1; i++) { 1539 lwords = 7 + (i * 3); 1540 if (lwords & 1) 1541 lwords++; /* pad it with 1 lword */ 1542 txd_sizes[i].qwords = lwords >> 1; 1543 txd_sizes[i].bytes = lwords << 2; 1544 } 1545 } 1546 1547 /* bdx_tx_init - initialize all Tx related stuff. 1548 * Namely, TXD and TXF fifos, database etc */ 1549 static int bdx_tx_init(struct bdx_priv *priv) 1550 { 1551 if (bdx_fifo_init(priv, &priv->txd_fifo0.m, priv->txd_size, 1552 regTXD_CFG0_0, 1553 regTXD_CFG1_0, regTXD_RPTR_0, regTXD_WPTR_0)) 1554 goto err_mem; 1555 if (bdx_fifo_init(priv, &priv->txf_fifo0.m, priv->txf_size, 1556 regTXF_CFG0_0, 1557 regTXF_CFG1_0, regTXF_RPTR_0, regTXF_WPTR_0)) 1558 goto err_mem; 1559 1560 /* The TX db has to keep mappings for all packets sent (on TxD) 1561 * and not yet reclaimed (on TxF) */ 1562 if (bdx_tx_db_init(&priv->txdb, max(priv->txd_size, priv->txf_size))) 1563 goto err_mem; 1564 1565 priv->tx_level = BDX_MAX_TX_LEVEL; 1566 #ifdef BDX_DELAY_WPTR 1567 priv->tx_update_mark = priv->tx_level - 1024; 1568 #endif 1569 return 0; 1570 1571 err_mem: 1572 netdev_err(priv->ndev, "Tx init failed\n"); 1573 return -ENOMEM; 1574 } 1575 1576 /** 1577 * bdx_tx_space - calculates available space in TX fifo 1578 * @priv: NIC private structure 1579 * 1580 * Returns available space in TX fifo in bytes 1581 */ 1582 static inline int bdx_tx_space(struct bdx_priv *priv) 1583 { 1584 struct txd_fifo *f = &priv->txd_fifo0; 1585 int fsize; 1586 1587 f->m.rptr = READ_REG(priv, f->m.reg_RPTR) & TXF_WPTR_WR_PTR; 1588 fsize = f->m.rptr - f->m.wptr; 1589 if (fsize <= 0) 1590 fsize = f->m.memsz + fsize; 1591 return fsize; 1592 } 1593 1594 /** 1595 * bdx_tx_transmit - send packet to NIC 1596 * @skb: packet to send 1597 * @ndev: network device assigned to NIC 1598 * Return codes: 1599 * o NETDEV_TX_OK everything ok. 1600 * o NETDEV_TX_BUSY Cannot transmit packet, try later 1601 * Usually a bug, means queue start/stop flow control is broken in 1602 * the driver. Note: the driver must NOT put the skb in its DMA ring. 1603 */ 1604 static netdev_tx_t bdx_tx_transmit(struct sk_buff *skb, 1605 struct net_device *ndev) 1606 { 1607 struct bdx_priv *priv = netdev_priv(ndev); 1608 struct txd_fifo *f = &priv->txd_fifo0; 1609 int txd_checksum = 7; /* full checksum */ 1610 int txd_lgsnd = 0; 1611 int txd_vlan_id = 0; 1612 int txd_vtag = 0; 1613 int txd_mss = 0; 1614 1615 int nr_frags = skb_shinfo(skb)->nr_frags; 1616 struct txd_desc *txdd; 1617 int len; 1618 unsigned long flags; 1619 1620 ENTER; 1621 local_irq_save(flags); 1622 spin_lock(&priv->tx_lock); 1623 1624 /* build tx descriptor */ 1625 BDX_ASSERT(f->m.wptr >= f->m.memsz); /* started with valid wptr */ 1626 txdd = (struct txd_desc *)(f->m.va + f->m.wptr); 1627 if (unlikely(skb->ip_summed != CHECKSUM_PARTIAL)) 1628 txd_checksum = 0; 1629 1630 if (skb_shinfo(skb)->gso_size) { 1631 txd_mss = skb_shinfo(skb)->gso_size; 1632 txd_lgsnd = 1; 1633 DBG("skb %p skb len %d gso size = %d\n", skb, skb->len, 1634 txd_mss); 1635 } 1636 1637 if (skb_vlan_tag_present(skb)) { 1638 /*Cut VLAN ID to 12 bits */ 1639 txd_vlan_id = skb_vlan_tag_get(skb) & BITS_MASK(12); 1640 txd_vtag = 1; 1641 } 1642 1643 txdd->length = CPU_CHIP_SWAP16(skb->len); 1644 txdd->mss = CPU_CHIP_SWAP16(txd_mss); 1645 txdd->txd_val1 = 1646 CPU_CHIP_SWAP32(TXD_W1_VAL 1647 (txd_sizes[nr_frags].qwords, txd_checksum, txd_vtag, 1648 txd_lgsnd, txd_vlan_id)); 1649 DBG("=== TxD desc =====================\n"); 1650 DBG("=== w1: 0x%x ================\n", txdd->txd_val1); 1651 DBG("=== w2: mss 0x%x len 0x%x\n", txdd->mss, txdd->length); 1652 1653 bdx_tx_map_skb(priv, skb, txdd); 1654 1655 /* increment TXD write pointer. In case of 1656 fifo wrapping copy reminder of the descriptor 1657 to the beginning */ 1658 f->m.wptr += txd_sizes[nr_frags].bytes; 1659 len = f->m.wptr - f->m.memsz; 1660 if (unlikely(len >= 0)) { 1661 f->m.wptr = len; 1662 if (len > 0) { 1663 BDX_ASSERT(len > f->m.memsz); 1664 memcpy(f->m.va, f->m.va + f->m.memsz, len); 1665 } 1666 } 1667 BDX_ASSERT(f->m.wptr >= f->m.memsz); /* finished with valid wptr */ 1668 1669 priv->tx_level -= txd_sizes[nr_frags].bytes; 1670 BDX_ASSERT(priv->tx_level <= 0 || priv->tx_level > BDX_MAX_TX_LEVEL); 1671 #ifdef BDX_DELAY_WPTR 1672 if (priv->tx_level > priv->tx_update_mark) { 1673 /* Force memory writes to complete before letting h/w 1674 know there are new descriptors to fetch. 1675 (might be needed on platforms like IA64) 1676 wmb(); */ 1677 WRITE_REG(priv, f->m.reg_WPTR, f->m.wptr & TXF_WPTR_WR_PTR); 1678 } else { 1679 if (priv->tx_noupd++ > BDX_NO_UPD_PACKETS) { 1680 priv->tx_noupd = 0; 1681 WRITE_REG(priv, f->m.reg_WPTR, 1682 f->m.wptr & TXF_WPTR_WR_PTR); 1683 } 1684 } 1685 #else 1686 /* Force memory writes to complete before letting h/w 1687 know there are new descriptors to fetch. 1688 (might be needed on platforms like IA64) 1689 wmb(); */ 1690 WRITE_REG(priv, f->m.reg_WPTR, f->m.wptr & TXF_WPTR_WR_PTR); 1691 1692 #endif 1693 #ifdef BDX_LLTX 1694 netif_trans_update(ndev); /* NETIF_F_LLTX driver :( */ 1695 #endif 1696 ndev->stats.tx_packets++; 1697 ndev->stats.tx_bytes += skb->len; 1698 1699 if (priv->tx_level < BDX_MIN_TX_LEVEL) { 1700 DBG("%s: %s: TX Q STOP level %d\n", 1701 BDX_DRV_NAME, ndev->name, priv->tx_level); 1702 netif_stop_queue(ndev); 1703 } 1704 1705 spin_unlock_irqrestore(&priv->tx_lock, flags); 1706 return NETDEV_TX_OK; 1707 } 1708 1709 /** 1710 * bdx_tx_cleanup - clean TXF fifo, run in the context of IRQ. 1711 * @priv: bdx adapter 1712 * 1713 * It scans TXF fifo for descriptors, frees DMA mappings and reports to OS 1714 * that those packets were sent 1715 */ 1716 static void bdx_tx_cleanup(struct bdx_priv *priv) 1717 { 1718 struct txf_fifo *f = &priv->txf_fifo0; 1719 struct txdb *db = &priv->txdb; 1720 int tx_level = 0; 1721 1722 ENTER; 1723 f->m.wptr = READ_REG(priv, f->m.reg_WPTR) & TXF_WPTR_MASK; 1724 BDX_ASSERT(f->m.rptr >= f->m.memsz); /* started with valid rptr */ 1725 1726 while (f->m.wptr != f->m.rptr) { 1727 f->m.rptr += BDX_TXF_DESC_SZ; 1728 f->m.rptr &= f->m.size_mask; 1729 1730 /* unmap all the fragments */ 1731 /* first has to come tx_maps containing dma */ 1732 BDX_ASSERT(db->rptr->len == 0); 1733 do { 1734 BDX_ASSERT(db->rptr->addr.dma == 0); 1735 pci_unmap_page(priv->pdev, db->rptr->addr.dma, 1736 db->rptr->len, PCI_DMA_TODEVICE); 1737 bdx_tx_db_inc_rptr(db); 1738 } while (db->rptr->len > 0); 1739 tx_level -= db->rptr->len; /* '-' koz len is negative */ 1740 1741 /* now should come skb pointer - free it */ 1742 dev_kfree_skb_irq(db->rptr->addr.skb); 1743 bdx_tx_db_inc_rptr(db); 1744 } 1745 1746 /* let h/w know which TXF descriptors were cleaned */ 1747 BDX_ASSERT((f->m.wptr & TXF_WPTR_WR_PTR) >= f->m.memsz); 1748 WRITE_REG(priv, f->m.reg_RPTR, f->m.rptr & TXF_WPTR_WR_PTR); 1749 1750 /* We reclaimed resources, so in case the Q is stopped by xmit callback, 1751 * we resume the transmission and use tx_lock to synchronize with xmit.*/ 1752 spin_lock(&priv->tx_lock); 1753 priv->tx_level += tx_level; 1754 BDX_ASSERT(priv->tx_level <= 0 || priv->tx_level > BDX_MAX_TX_LEVEL); 1755 #ifdef BDX_DELAY_WPTR 1756 if (priv->tx_noupd) { 1757 priv->tx_noupd = 0; 1758 WRITE_REG(priv, priv->txd_fifo0.m.reg_WPTR, 1759 priv->txd_fifo0.m.wptr & TXF_WPTR_WR_PTR); 1760 } 1761 #endif 1762 1763 if (unlikely(netif_queue_stopped(priv->ndev) && 1764 netif_carrier_ok(priv->ndev) && 1765 (priv->tx_level >= BDX_MIN_TX_LEVEL))) { 1766 DBG("%s: %s: TX Q WAKE level %d\n", 1767 BDX_DRV_NAME, priv->ndev->name, priv->tx_level); 1768 netif_wake_queue(priv->ndev); 1769 } 1770 spin_unlock(&priv->tx_lock); 1771 } 1772 1773 /** 1774 * bdx_tx_free_skbs - frees all skbs from TXD fifo. 1775 * It gets called when OS stops this dev, eg upon "ifconfig down" or rmmod 1776 */ 1777 static void bdx_tx_free_skbs(struct bdx_priv *priv) 1778 { 1779 struct txdb *db = &priv->txdb; 1780 1781 ENTER; 1782 while (db->rptr != db->wptr) { 1783 if (likely(db->rptr->len)) 1784 pci_unmap_page(priv->pdev, db->rptr->addr.dma, 1785 db->rptr->len, PCI_DMA_TODEVICE); 1786 else 1787 dev_kfree_skb(db->rptr->addr.skb); 1788 bdx_tx_db_inc_rptr(db); 1789 } 1790 RET(); 1791 } 1792 1793 /* bdx_tx_free - frees all Tx resources */ 1794 static void bdx_tx_free(struct bdx_priv *priv) 1795 { 1796 ENTER; 1797 bdx_tx_free_skbs(priv); 1798 bdx_fifo_free(priv, &priv->txd_fifo0.m); 1799 bdx_fifo_free(priv, &priv->txf_fifo0.m); 1800 bdx_tx_db_close(&priv->txdb); 1801 } 1802 1803 /** 1804 * bdx_tx_push_desc - push descriptor to TxD fifo 1805 * @priv: NIC private structure 1806 * @data: desc's data 1807 * @size: desc's size 1808 * 1809 * Pushes desc to TxD fifo and overlaps it if needed. 1810 * NOTE: this func does not check for available space. this is responsibility 1811 * of the caller. Neither does it check that data size is smaller than 1812 * fifo size. 1813 */ 1814 static void bdx_tx_push_desc(struct bdx_priv *priv, void *data, int size) 1815 { 1816 struct txd_fifo *f = &priv->txd_fifo0; 1817 int i = f->m.memsz - f->m.wptr; 1818 1819 if (size == 0) 1820 return; 1821 1822 if (i > size) { 1823 memcpy(f->m.va + f->m.wptr, data, size); 1824 f->m.wptr += size; 1825 } else { 1826 memcpy(f->m.va + f->m.wptr, data, i); 1827 f->m.wptr = size - i; 1828 memcpy(f->m.va, data + i, f->m.wptr); 1829 } 1830 WRITE_REG(priv, f->m.reg_WPTR, f->m.wptr & TXF_WPTR_WR_PTR); 1831 } 1832 1833 /** 1834 * bdx_tx_push_desc_safe - push descriptor to TxD fifo in a safe way 1835 * @priv: NIC private structure 1836 * @data: desc's data 1837 * @size: desc's size 1838 * 1839 * NOTE: this func does check for available space and, if necessary, waits for 1840 * NIC to read existing data before writing new one. 1841 */ 1842 static void bdx_tx_push_desc_safe(struct bdx_priv *priv, void *data, int size) 1843 { 1844 int timer = 0; 1845 ENTER; 1846 1847 while (size > 0) { 1848 /* we substruct 8 because when fifo is full rptr == wptr 1849 which also means that fifo is empty, we can understand 1850 the difference, but could hw do the same ??? :) */ 1851 int avail = bdx_tx_space(priv) - 8; 1852 if (avail <= 0) { 1853 if (timer++ > 300) { /* prevent endless loop */ 1854 DBG("timeout while writing desc to TxD fifo\n"); 1855 break; 1856 } 1857 udelay(50); /* give hw a chance to clean fifo */ 1858 continue; 1859 } 1860 avail = min(avail, size); 1861 DBG("about to push %d bytes starting %p size %d\n", avail, 1862 data, size); 1863 bdx_tx_push_desc(priv, data, avail); 1864 size -= avail; 1865 data += avail; 1866 } 1867 RET(); 1868 } 1869 1870 static const struct net_device_ops bdx_netdev_ops = { 1871 .ndo_open = bdx_open, 1872 .ndo_stop = bdx_close, 1873 .ndo_start_xmit = bdx_tx_transmit, 1874 .ndo_validate_addr = eth_validate_addr, 1875 .ndo_do_ioctl = bdx_ioctl, 1876 .ndo_set_rx_mode = bdx_setmulti, 1877 .ndo_change_mtu = bdx_change_mtu, 1878 .ndo_set_mac_address = bdx_set_mac, 1879 .ndo_vlan_rx_add_vid = bdx_vlan_rx_add_vid, 1880 .ndo_vlan_rx_kill_vid = bdx_vlan_rx_kill_vid, 1881 }; 1882 1883 /** 1884 * bdx_probe - Device Initialization Routine 1885 * @pdev: PCI device information struct 1886 * @ent: entry in bdx_pci_tbl 1887 * 1888 * Returns 0 on success, negative on failure 1889 * 1890 * bdx_probe initializes an adapter identified by a pci_dev structure. 1891 * The OS initialization, configuring of the adapter private structure, 1892 * and a hardware reset occur. 1893 * 1894 * functions and their order used as explained in 1895 * /usr/src/linux/Documentation/DMA-{API,mapping}.txt 1896 * 1897 */ 1898 1899 /* TBD: netif_msg should be checked and implemented. I disable it for now */ 1900 static int 1901 bdx_probe(struct pci_dev *pdev, const struct pci_device_id *ent) 1902 { 1903 struct net_device *ndev; 1904 struct bdx_priv *priv; 1905 int err, pci_using_dac, port; 1906 unsigned long pciaddr; 1907 u32 regionSize; 1908 struct pci_nic *nic; 1909 1910 ENTER; 1911 1912 nic = vmalloc(sizeof(*nic)); 1913 if (!nic) 1914 RET(-ENOMEM); 1915 1916 /************** pci *****************/ 1917 err = pci_enable_device(pdev); 1918 if (err) /* it triggers interrupt, dunno why. */ 1919 goto err_pci; /* it's not a problem though */ 1920 1921 if (!(err = pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) && 1922 !(err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64)))) { 1923 pci_using_dac = 1; 1924 } else { 1925 if ((err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) || 1926 (err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32)))) { 1927 pr_err("No usable DMA configuration, aborting\n"); 1928 goto err_dma; 1929 } 1930 pci_using_dac = 0; 1931 } 1932 1933 err = pci_request_regions(pdev, BDX_DRV_NAME); 1934 if (err) 1935 goto err_dma; 1936 1937 pci_set_master(pdev); 1938 1939 pciaddr = pci_resource_start(pdev, 0); 1940 if (!pciaddr) { 1941 err = -EIO; 1942 pr_err("no MMIO resource\n"); 1943 goto err_out_res; 1944 } 1945 regionSize = pci_resource_len(pdev, 0); 1946 if (regionSize < BDX_REGS_SIZE) { 1947 err = -EIO; 1948 pr_err("MMIO resource (%x) too small\n", regionSize); 1949 goto err_out_res; 1950 } 1951 1952 nic->regs = ioremap(pciaddr, regionSize); 1953 if (!nic->regs) { 1954 err = -EIO; 1955 pr_err("ioremap failed\n"); 1956 goto err_out_res; 1957 } 1958 1959 if (pdev->irq < 2) { 1960 err = -EIO; 1961 pr_err("invalid irq (%d)\n", pdev->irq); 1962 goto err_out_iomap; 1963 } 1964 pci_set_drvdata(pdev, nic); 1965 1966 if (pdev->device == 0x3014) 1967 nic->port_num = 2; 1968 else 1969 nic->port_num = 1; 1970 1971 print_hw_id(pdev); 1972 1973 bdx_hw_reset_direct(nic->regs); 1974 1975 nic->irq_type = IRQ_INTX; 1976 #ifdef BDX_MSI 1977 if ((readl(nic->regs + FPGA_VER) & 0xFFF) >= 378) { 1978 err = pci_enable_msi(pdev); 1979 if (err) 1980 pr_err("Can't enable msi. error is %d\n", err); 1981 else 1982 nic->irq_type = IRQ_MSI; 1983 } else 1984 DBG("HW does not support MSI\n"); 1985 #endif 1986 1987 /************** netdev **************/ 1988 for (port = 0; port < nic->port_num; port++) { 1989 ndev = alloc_etherdev(sizeof(struct bdx_priv)); 1990 if (!ndev) { 1991 err = -ENOMEM; 1992 goto err_out_iomap; 1993 } 1994 1995 ndev->netdev_ops = &bdx_netdev_ops; 1996 ndev->tx_queue_len = BDX_NDEV_TXQ_LEN; 1997 1998 bdx_set_ethtool_ops(ndev); /* ethtool interface */ 1999 2000 /* these fields are used for info purposes only 2001 * so we can have them same for all ports of the board */ 2002 ndev->if_port = port; 2003 ndev->features = NETIF_F_IP_CSUM | NETIF_F_SG | NETIF_F_TSO 2004 | NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX | 2005 NETIF_F_HW_VLAN_CTAG_FILTER | NETIF_F_RXCSUM 2006 ; 2007 ndev->hw_features = NETIF_F_IP_CSUM | NETIF_F_SG | 2008 NETIF_F_TSO | NETIF_F_HW_VLAN_CTAG_TX; 2009 2010 if (pci_using_dac) 2011 ndev->features |= NETIF_F_HIGHDMA; 2012 2013 /************** priv ****************/ 2014 priv = nic->priv[port] = netdev_priv(ndev); 2015 2016 priv->pBdxRegs = nic->regs + port * 0x8000; 2017 priv->port = port; 2018 priv->pdev = pdev; 2019 priv->ndev = ndev; 2020 priv->nic = nic; 2021 priv->msg_enable = BDX_DEF_MSG_ENABLE; 2022 2023 netif_napi_add(ndev, &priv->napi, bdx_poll, 64); 2024 2025 if ((readl(nic->regs + FPGA_VER) & 0xFFF) == 308) { 2026 DBG("HW statistics not supported\n"); 2027 priv->stats_flag = 0; 2028 } else { 2029 priv->stats_flag = 1; 2030 } 2031 2032 /* Initialize fifo sizes. */ 2033 priv->txd_size = 2; 2034 priv->txf_size = 2; 2035 priv->rxd_size = 2; 2036 priv->rxf_size = 3; 2037 2038 /* Initialize the initial coalescing registers. */ 2039 priv->rdintcm = INT_REG_VAL(0x20, 1, 4, 12); 2040 priv->tdintcm = INT_REG_VAL(0x20, 1, 0, 12); 2041 2042 /* ndev->xmit_lock spinlock is not used. 2043 * Private priv->tx_lock is used for synchronization 2044 * between transmit and TX irq cleanup. In addition 2045 * set multicast list callback has to use priv->tx_lock. 2046 */ 2047 #ifdef BDX_LLTX 2048 ndev->features |= NETIF_F_LLTX; 2049 #endif 2050 /* MTU range: 60 - 16384 */ 2051 ndev->min_mtu = ETH_ZLEN; 2052 ndev->max_mtu = BDX_MAX_MTU; 2053 2054 spin_lock_init(&priv->tx_lock); 2055 2056 /*bdx_hw_reset(priv); */ 2057 if (bdx_read_mac(priv)) { 2058 pr_err("load MAC address failed\n"); 2059 goto err_out_iomap; 2060 } 2061 SET_NETDEV_DEV(ndev, &pdev->dev); 2062 err = register_netdev(ndev); 2063 if (err) { 2064 pr_err("register_netdev failed\n"); 2065 goto err_out_free; 2066 } 2067 netif_carrier_off(ndev); 2068 netif_stop_queue(ndev); 2069 2070 print_eth_id(ndev); 2071 } 2072 RET(0); 2073 2074 err_out_free: 2075 free_netdev(ndev); 2076 err_out_iomap: 2077 iounmap(nic->regs); 2078 err_out_res: 2079 pci_release_regions(pdev); 2080 err_dma: 2081 pci_disable_device(pdev); 2082 err_pci: 2083 vfree(nic); 2084 2085 RET(err); 2086 } 2087 2088 /****************** Ethtool interface *********************/ 2089 /* get strings for statistics counters */ 2090 static const char 2091 bdx_stat_names[][ETH_GSTRING_LEN] = { 2092 "InUCast", /* 0x7200 */ 2093 "InMCast", /* 0x7210 */ 2094 "InBCast", /* 0x7220 */ 2095 "InPkts", /* 0x7230 */ 2096 "InErrors", /* 0x7240 */ 2097 "InDropped", /* 0x7250 */ 2098 "FrameTooLong", /* 0x7260 */ 2099 "FrameSequenceErrors", /* 0x7270 */ 2100 "InVLAN", /* 0x7280 */ 2101 "InDroppedDFE", /* 0x7290 */ 2102 "InDroppedIntFull", /* 0x72A0 */ 2103 "InFrameAlignErrors", /* 0x72B0 */ 2104 2105 /* 0x72C0-0x72E0 RSRV */ 2106 2107 "OutUCast", /* 0x72F0 */ 2108 "OutMCast", /* 0x7300 */ 2109 "OutBCast", /* 0x7310 */ 2110 "OutPkts", /* 0x7320 */ 2111 2112 /* 0x7330-0x7360 RSRV */ 2113 2114 "OutVLAN", /* 0x7370 */ 2115 "InUCastOctects", /* 0x7380 */ 2116 "OutUCastOctects", /* 0x7390 */ 2117 2118 /* 0x73A0-0x73B0 RSRV */ 2119 2120 "InBCastOctects", /* 0x73C0 */ 2121 "OutBCastOctects", /* 0x73D0 */ 2122 "InOctects", /* 0x73E0 */ 2123 "OutOctects", /* 0x73F0 */ 2124 }; 2125 2126 /* 2127 * bdx_get_link_ksettings - get device-specific settings 2128 * @netdev 2129 * @ecmd 2130 */ 2131 static int bdx_get_link_ksettings(struct net_device *netdev, 2132 struct ethtool_link_ksettings *ecmd) 2133 { 2134 ethtool_link_ksettings_zero_link_mode(ecmd, supported); 2135 ethtool_link_ksettings_add_link_mode(ecmd, supported, 2136 10000baseT_Full); 2137 ethtool_link_ksettings_add_link_mode(ecmd, supported, FIBRE); 2138 ethtool_link_ksettings_zero_link_mode(ecmd, advertising); 2139 ethtool_link_ksettings_add_link_mode(ecmd, advertising, 2140 10000baseT_Full); 2141 ethtool_link_ksettings_add_link_mode(ecmd, advertising, FIBRE); 2142 2143 ecmd->base.speed = SPEED_10000; 2144 ecmd->base.duplex = DUPLEX_FULL; 2145 ecmd->base.port = PORT_FIBRE; 2146 ecmd->base.autoneg = AUTONEG_DISABLE; 2147 2148 return 0; 2149 } 2150 2151 /* 2152 * bdx_get_drvinfo - report driver information 2153 * @netdev 2154 * @drvinfo 2155 */ 2156 static void 2157 bdx_get_drvinfo(struct net_device *netdev, struct ethtool_drvinfo *drvinfo) 2158 { 2159 struct bdx_priv *priv = netdev_priv(netdev); 2160 2161 strlcpy(drvinfo->driver, BDX_DRV_NAME, sizeof(drvinfo->driver)); 2162 strlcpy(drvinfo->version, BDX_DRV_VERSION, sizeof(drvinfo->version)); 2163 strlcpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version)); 2164 strlcpy(drvinfo->bus_info, pci_name(priv->pdev), 2165 sizeof(drvinfo->bus_info)); 2166 } 2167 2168 /* 2169 * bdx_get_coalesce - get interrupt coalescing parameters 2170 * @netdev 2171 * @ecoal 2172 */ 2173 static int 2174 bdx_get_coalesce(struct net_device *netdev, struct ethtool_coalesce *ecoal) 2175 { 2176 u32 rdintcm; 2177 u32 tdintcm; 2178 struct bdx_priv *priv = netdev_priv(netdev); 2179 2180 rdintcm = priv->rdintcm; 2181 tdintcm = priv->tdintcm; 2182 2183 /* PCK_TH measures in multiples of FIFO bytes 2184 We translate to packets */ 2185 ecoal->rx_coalesce_usecs = GET_INT_COAL(rdintcm) * INT_COAL_MULT; 2186 ecoal->rx_max_coalesced_frames = 2187 ((GET_PCK_TH(rdintcm) * PCK_TH_MULT) / sizeof(struct rxf_desc)); 2188 2189 ecoal->tx_coalesce_usecs = GET_INT_COAL(tdintcm) * INT_COAL_MULT; 2190 ecoal->tx_max_coalesced_frames = 2191 ((GET_PCK_TH(tdintcm) * PCK_TH_MULT) / BDX_TXF_DESC_SZ); 2192 2193 /* adaptive parameters ignored */ 2194 return 0; 2195 } 2196 2197 /* 2198 * bdx_set_coalesce - set interrupt coalescing parameters 2199 * @netdev 2200 * @ecoal 2201 */ 2202 static int 2203 bdx_set_coalesce(struct net_device *netdev, struct ethtool_coalesce *ecoal) 2204 { 2205 u32 rdintcm; 2206 u32 tdintcm; 2207 struct bdx_priv *priv = netdev_priv(netdev); 2208 int rx_coal; 2209 int tx_coal; 2210 int rx_max_coal; 2211 int tx_max_coal; 2212 2213 /* Check for valid input */ 2214 rx_coal = ecoal->rx_coalesce_usecs / INT_COAL_MULT; 2215 tx_coal = ecoal->tx_coalesce_usecs / INT_COAL_MULT; 2216 rx_max_coal = ecoal->rx_max_coalesced_frames; 2217 tx_max_coal = ecoal->tx_max_coalesced_frames; 2218 2219 /* Translate from packets to multiples of FIFO bytes */ 2220 rx_max_coal = 2221 (((rx_max_coal * sizeof(struct rxf_desc)) + PCK_TH_MULT - 1) 2222 / PCK_TH_MULT); 2223 tx_max_coal = 2224 (((tx_max_coal * BDX_TXF_DESC_SZ) + PCK_TH_MULT - 1) 2225 / PCK_TH_MULT); 2226 2227 if ((rx_coal > 0x7FFF) || (tx_coal > 0x7FFF) || 2228 (rx_max_coal > 0xF) || (tx_max_coal > 0xF)) 2229 return -EINVAL; 2230 2231 rdintcm = INT_REG_VAL(rx_coal, GET_INT_COAL_RC(priv->rdintcm), 2232 GET_RXF_TH(priv->rdintcm), rx_max_coal); 2233 tdintcm = INT_REG_VAL(tx_coal, GET_INT_COAL_RC(priv->tdintcm), 0, 2234 tx_max_coal); 2235 2236 priv->rdintcm = rdintcm; 2237 priv->tdintcm = tdintcm; 2238 2239 WRITE_REG(priv, regRDINTCM0, rdintcm); 2240 WRITE_REG(priv, regTDINTCM0, tdintcm); 2241 2242 return 0; 2243 } 2244 2245 /* Convert RX fifo size to number of pending packets */ 2246 static inline int bdx_rx_fifo_size_to_packets(int rx_size) 2247 { 2248 return (FIFO_SIZE * (1 << rx_size)) / sizeof(struct rxf_desc); 2249 } 2250 2251 /* Convert TX fifo size to number of pending packets */ 2252 static inline int bdx_tx_fifo_size_to_packets(int tx_size) 2253 { 2254 return (FIFO_SIZE * (1 << tx_size)) / BDX_TXF_DESC_SZ; 2255 } 2256 2257 /* 2258 * bdx_get_ringparam - report ring sizes 2259 * @netdev 2260 * @ring 2261 */ 2262 static void 2263 bdx_get_ringparam(struct net_device *netdev, struct ethtool_ringparam *ring) 2264 { 2265 struct bdx_priv *priv = netdev_priv(netdev); 2266 2267 /*max_pending - the maximum-sized FIFO we allow */ 2268 ring->rx_max_pending = bdx_rx_fifo_size_to_packets(3); 2269 ring->tx_max_pending = bdx_tx_fifo_size_to_packets(3); 2270 ring->rx_pending = bdx_rx_fifo_size_to_packets(priv->rxf_size); 2271 ring->tx_pending = bdx_tx_fifo_size_to_packets(priv->txd_size); 2272 } 2273 2274 /* 2275 * bdx_set_ringparam - set ring sizes 2276 * @netdev 2277 * @ring 2278 */ 2279 static int 2280 bdx_set_ringparam(struct net_device *netdev, struct ethtool_ringparam *ring) 2281 { 2282 struct bdx_priv *priv = netdev_priv(netdev); 2283 int rx_size = 0; 2284 int tx_size = 0; 2285 2286 for (; rx_size < 4; rx_size++) { 2287 if (bdx_rx_fifo_size_to_packets(rx_size) >= ring->rx_pending) 2288 break; 2289 } 2290 if (rx_size == 4) 2291 rx_size = 3; 2292 2293 for (; tx_size < 4; tx_size++) { 2294 if (bdx_tx_fifo_size_to_packets(tx_size) >= ring->tx_pending) 2295 break; 2296 } 2297 if (tx_size == 4) 2298 tx_size = 3; 2299 2300 /*Is there anything to do? */ 2301 if ((rx_size == priv->rxf_size) && 2302 (tx_size == priv->txd_size)) 2303 return 0; 2304 2305 priv->rxf_size = rx_size; 2306 if (rx_size > 1) 2307 priv->rxd_size = rx_size - 1; 2308 else 2309 priv->rxd_size = rx_size; 2310 2311 priv->txf_size = priv->txd_size = tx_size; 2312 2313 if (netif_running(netdev)) { 2314 bdx_close(netdev); 2315 bdx_open(netdev); 2316 } 2317 return 0; 2318 } 2319 2320 /* 2321 * bdx_get_strings - return a set of strings that describe the requested objects 2322 * @netdev 2323 * @data 2324 */ 2325 static void bdx_get_strings(struct net_device *netdev, u32 stringset, u8 *data) 2326 { 2327 switch (stringset) { 2328 case ETH_SS_STATS: 2329 memcpy(data, *bdx_stat_names, sizeof(bdx_stat_names)); 2330 break; 2331 } 2332 } 2333 2334 /* 2335 * bdx_get_sset_count - return number of statistics or tests 2336 * @netdev 2337 */ 2338 static int bdx_get_sset_count(struct net_device *netdev, int stringset) 2339 { 2340 struct bdx_priv *priv = netdev_priv(netdev); 2341 2342 switch (stringset) { 2343 case ETH_SS_STATS: 2344 BDX_ASSERT(ARRAY_SIZE(bdx_stat_names) 2345 != sizeof(struct bdx_stats) / sizeof(u64)); 2346 return (priv->stats_flag) ? ARRAY_SIZE(bdx_stat_names) : 0; 2347 } 2348 2349 return -EINVAL; 2350 } 2351 2352 /* 2353 * bdx_get_ethtool_stats - return device's hardware L2 statistics 2354 * @netdev 2355 * @stats 2356 * @data 2357 */ 2358 static void bdx_get_ethtool_stats(struct net_device *netdev, 2359 struct ethtool_stats *stats, u64 *data) 2360 { 2361 struct bdx_priv *priv = netdev_priv(netdev); 2362 2363 if (priv->stats_flag) { 2364 2365 /* Update stats from HW */ 2366 bdx_update_stats(priv); 2367 2368 /* Copy data to user buffer */ 2369 memcpy(data, &priv->hw_stats, sizeof(priv->hw_stats)); 2370 } 2371 } 2372 2373 /* 2374 * bdx_set_ethtool_ops - ethtool interface implementation 2375 * @netdev 2376 */ 2377 static void bdx_set_ethtool_ops(struct net_device *netdev) 2378 { 2379 static const struct ethtool_ops bdx_ethtool_ops = { 2380 .get_drvinfo = bdx_get_drvinfo, 2381 .get_link = ethtool_op_get_link, 2382 .get_coalesce = bdx_get_coalesce, 2383 .set_coalesce = bdx_set_coalesce, 2384 .get_ringparam = bdx_get_ringparam, 2385 .set_ringparam = bdx_set_ringparam, 2386 .get_strings = bdx_get_strings, 2387 .get_sset_count = bdx_get_sset_count, 2388 .get_ethtool_stats = bdx_get_ethtool_stats, 2389 .get_link_ksettings = bdx_get_link_ksettings, 2390 }; 2391 2392 netdev->ethtool_ops = &bdx_ethtool_ops; 2393 } 2394 2395 /** 2396 * bdx_remove - Device Removal Routine 2397 * @pdev: PCI device information struct 2398 * 2399 * bdx_remove is called by the PCI subsystem to alert the driver 2400 * that it should release a PCI device. The could be caused by a 2401 * Hot-Plug event, or because the driver is going to be removed from 2402 * memory. 2403 **/ 2404 static void bdx_remove(struct pci_dev *pdev) 2405 { 2406 struct pci_nic *nic = pci_get_drvdata(pdev); 2407 struct net_device *ndev; 2408 int port; 2409 2410 for (port = 0; port < nic->port_num; port++) { 2411 ndev = nic->priv[port]->ndev; 2412 unregister_netdev(ndev); 2413 free_netdev(ndev); 2414 } 2415 2416 /*bdx_hw_reset_direct(nic->regs); */ 2417 #ifdef BDX_MSI 2418 if (nic->irq_type == IRQ_MSI) 2419 pci_disable_msi(pdev); 2420 #endif 2421 2422 iounmap(nic->regs); 2423 pci_release_regions(pdev); 2424 pci_disable_device(pdev); 2425 vfree(nic); 2426 2427 RET(); 2428 } 2429 2430 static struct pci_driver bdx_pci_driver = { 2431 .name = BDX_DRV_NAME, 2432 .id_table = bdx_pci_tbl, 2433 .probe = bdx_probe, 2434 .remove = bdx_remove, 2435 }; 2436 2437 /* 2438 * print_driver_id - print parameters of the driver build 2439 */ 2440 static void __init print_driver_id(void) 2441 { 2442 pr_info("%s, %s\n", BDX_DRV_DESC, BDX_DRV_VERSION); 2443 pr_info("Options: hw_csum %s\n", BDX_MSI_STRING); 2444 } 2445 2446 static int __init bdx_module_init(void) 2447 { 2448 ENTER; 2449 init_txd_sizes(); 2450 print_driver_id(); 2451 RET(pci_register_driver(&bdx_pci_driver)); 2452 } 2453 2454 module_init(bdx_module_init); 2455 2456 static void __exit bdx_module_exit(void) 2457 { 2458 ENTER; 2459 pci_unregister_driver(&bdx_pci_driver); 2460 RET(); 2461 } 2462 2463 module_exit(bdx_module_exit); 2464 2465 MODULE_LICENSE("GPL"); 2466 MODULE_AUTHOR(DRIVER_AUTHOR); 2467 MODULE_DESCRIPTION(BDX_DRV_DESC); 2468 MODULE_FIRMWARE("tehuti/bdx.bin"); 2469